Class-Based Ethernet CoS Matching and Marking

The Class-Based Ethernet CoS Matching and Marking (801.1p and ISL CoS) feature allows you to mark and match packets using Class of Service (CoS) values.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.

Prerequisites for Class-Based Ethernet CoS Matching and Marking

When configuring this feature, you must first create a policy map (sometimes referred to as a service policy or a traffic policy) using the Modular QoS Command-Line Interface (CLI) (MQC). Therefore, you should be familiar with the procedure for creating a policy map using the MQC.

For more information about creating a policy map (traffic policy) using the MQC, see the “Applying QoS Features Using the MQC” module.

Information About Class-Based Ethernet CoS Matching and Marking

Layer 2 CoS Values

Layer 2 (L2) Class of Service (CoS) values are relevant for IEEE 802.1Q and Interswitch Link (ISL) types of frames. The Class-based Ethernet CoS Matching and Marking feature extends Cisco software capabilities to match packets by looking at the CoS value of the packet and marking packets with user-defined CoS values. This feature can be used for L2 CoS to L3 Terms of Service (TOS) mapping. CoS matching and marking can be configured via the Cisco Modular QoS CLI framework.

How to Configure Class-Based Ethernet CoS Matching and Marking

Configuring Class-Based Ethernet CoS Matching

In the following task, classes named voice and video-and-data are created to classify traffic based on the CoS values. The classes are configured in the CoS-based-treatment policy map, and the service policy is attached to all packets leaving Gigabit Ethernet interface 1/0/1.

SUMMARY STEPS

enable
configure terminal
class-map class-map-name
match cos cos-value
exit
class-map class-map-name
match cos cos-value
exit
policy-map policy-map-name
class {class-name | class-default }
priority level level
exit
class {class-name | class-default }
bandwidth remaining percent percentage
exit
exit
interface type number
service-policy {input | output } policy-map-name
end

DETAILED STEPS

Command or Action Purpose

Step 1

enable

Example:


Device> enable

Enables privileged EXEC mode.

Enter your password if prompted.

Step 2

configure terminal

Example:


Device# configure terminal

Enters global configuration mode.

Step 3

class-map class-map-name

Example:


Device(config)# class-map voice

Specifies the name of the class map to be created and enters class-map configuration mode.

Step 4

match cos cos-value

Example:


Device(config-cmap)# match cos 7

Configures the class map to match traffic on the basis of the CoS value.

Step 5

exit

Example:


Device(config-cmap)# exit

(Optional) Exits class-map configuration mode.

Step 6

class-map class-map-name

Example:


Device(config)# class-map video-and-data

Specifies the name of the class map to be created and enters class-map configuration mode.

Enter the class map name.

Step 7

match cos cos-value

Example:


Device(config-cmap)# match cos 5

Configures the class map to match traffic on the basis of the CoS value.

Step 8

exit

Example:


Device(config-cmap)# exit

(Optional) Exits class-map configuration mode.

Step 9

policy-map policy-map-name

Example:


Device(config)# policy-map cos-based-treatment

Specifies the name of the policy map created earlier and enters policy-map configuration mode.

Step 10

class {class-name | class-default }

Example:


Device(config-pmap)# class voice

Specifies the name of the class whose policy you want to create and enters policy-map class configuration mode. This class is associated with the class map created earlier.

Step 11

priority level level

Example:

Device(config-pmap-c)# priority level 1

Specifies the level of the priority service.

Step 12

exit

Example:


Device(config-pmap-c)# exit

(Optional) Exits policy-map class configuration mode.

Step 13

class {class-name | class-default }

Example:


Device(config-pmap)# class video-and-data

Specifies the name of the class whose policy you want to create and enters policy-map class configuration mode. This class is associated with the class map created earlier.

Step 14

bandwidth remaining percent percentage

Example:

Device(config-pmap-c)# bandwidth remaining percent 20

Specifies the amount of bandwidth assigned to the class.

Step 15

exit

Example:


Device(config-pmap-c)# exit

(Optional) Exits policy-map class configuration mode.

Step 16

exit

Example:


Device(config-pmap)# exit

(Optional) Exits policy-map configuration mode.

Step 17

interface type number

Example:


Device(config)# interface gigabitethernet 1/0/1

Configures an interface (or subinterface) type and enters interface configuration mode.

Step 18

service-policy {input | output } policy-map-name

Example:


Device(config-if)# service-policy output cos-based-treatment

Specifies the name of the policy map to be attached to either the input or output direction of the interface.

Note

Policy maps can be configured on ingress or egress devices. They can also be attached in the input or output direction of an interface. The direction (input or output) and the device (ingress or egress) to which the policy map should be attached vary according your network configuration. When using the service-policy command to attach the policy map to an interface, be sure to choose the device and the interface direction that are appropriate for your network configuration.

Step 19

end

Example:


Device(config-if)# end

(Optional) Exits interface configuration mode and returns to privileged EXEC mode.

Configuring Class-Based Ethernet CoS Marking

In the following task, the policy map called cos-set is created to assign different CoS values for different types of traffic.

Note

This task assumes that the class maps called voice and video-and-data have already been created.

SUMMARY STEPS

enable
configure terminal
policy-map policy-map-name
class {class-name | class-default }
set cos cos-value
exit
class {class-name | class-default }
set cos cos-value
end

DETAILED STEPS

	Command or Action	Purpose
Step 1	enable Example: `Device> enable`	Enables privileged EXEC mode. Enter your password if prompted.
Step 2	configure terminal Example: `Device# configure terminal`	Enters global configuration mode.
Step 3	policy-map `policy-map-name` Example: `Device(config)# policy-map cos-set`	Specifies the name of the policy map created earlier and enters policy-map configuration mode.
Step 4	class {`class-name` \| class-default } Example: `Device(config-pmap)# class voice`	Specifies the name of the class whose policy you want to create and enters policy-map class configuration mode. This class is associated with the class map created earlier.
Step 5	set cos `cos-value` Example: `Device(config-pmap-c)# set cos 1`	Sets the packet’s CoS value.
Step 6	exit Example: `Device(config-pmap-c)# exit`	Exits policy-map class configuration mode.
Step 7	class {`class-name` \| class-default } Example: `Device(config-pmap)# class video-and-data`	Specifies the name of the class whose policy you want to create and enters policy-map class configuration mode. This class is associated with the class map created earlier.
Step 8	set cos `cos-value` Example: `Device(config-pmap-c)# set cos 2`	Sets the packet’s CoS value.
Step 9	end Example: `Device(config-pmap-c)# end`	(Optional) Exits policy-map class configuration mode and returns to privileged EXEC mode.

Configuration Examples for Class-Based Ethernet CoS Matching and Marking

Example: Configuring Class-Based Ethernet CoS Matching

This example creates two classes, voice and video-and-data, to classify traffic based on the CoS values. The CoS-based-treatment policy map is used to set priority and bandwidth values for the classes. The service policy is attached to all packets leaving interface Gigabit Ethernet1/0/1.

Note

The service policy can be attached to any interface that supports service policies.


Device(config)# class-map voice
Device(config-cmap)# match cos 7
Device(config-cmap)# exit
Device(config)# class-map video-and-data
Device(config-cmap)# match cos 5
Device(config-cmap)# exit
Device(config)# policy-map cos-based-treatment
Device(config-pmap)# class voice
Device(config-pmap-c)# priority level 1
Device(config-pmap-c)# exit
Device(config-pmap)# class video-and-data
Device(config-pmap-c)# bandwidth remaining percent 20
Device(config-pmap-c)# exit
Device(config-pmap)# exit
Device(config)#  interface gigabitethernet1/0/1
Device(config-if)# service-policy output cos-based-treatment

Example: Class-Based Ethernet CoS Marking

Device(config)# policy-map cos-set
Device(config-pmap)# class voice
Device(config-pmap-c)# set cos 1
Device(config-pmap-c)# exit
Device(config-pmap)# class video-and-data
Device(config-pmap-c)# set cos 2
Device(config-pmap-c)# end

Additional References for Class-Based Ethernet CoS Matching and Marking

Related Topic	Document Title
Cisco commands	Cisco IOS Master Command List, All Releases
QoS commands: complete command syntax, command modes, command history, defaults, usage guidelines, and examples	Cisco IOS Quality of Service Solutions Command Reference
Classifying network traffic	“Classifying Network Traffic” module
MQC	“Applying QoS Features Using the MQC” module
Marking network traffic	“Marking Network Traffic” module

Technical Assistance


Description	Link
The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.	http://www.cisco.com/cisco/web/support/index.html

Feature Information for Class-Based Ethernet CoS Matching & Marking

The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

Table 1. Feature Information for Class-Based Ethernet CoS Matching and Marking
Feature Name	Releases	Feature Information
Class-Based Ethernet CoS Matching and Marking	12.2(5)T 15.0(1)S Cisco IOS XE Release 2.1 Cisco IOS XE Release 3.2SE	This feature allows you to mark and match packets using Class of Service (CoS) values. The following commands were introduced or modified: match cos , set cos .
User Priority Based QoS Marking for Wireless Deployments	Cisco IOS XE Release 3.2SE	This features allows you to mark and match packets on wireless deployments using the user-priority (CoS) vlaues.

QoS: Classification Configuration Guide, Cisco IOS XE 17

Bias-Free Language

Results

Chapter: Class-Based Ethernet CoS Matching and Marking

Class-Based Ethernet CoS Matching and Marking

Finding Feature Information

Prerequisites for Class-Based Ethernet CoS Matching and Marking

Layer 2 CoS Values

Configuring Class-Based Ethernet CoS Matching

SUMMARY STEPS

DETAILED STEPS

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Configuring Class-Based Ethernet CoS Marking

SUMMARY STEPS

DETAILED STEPS

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Example: Configuring Class-Based Ethernet CoS Matching

Example: Class-Based Ethernet CoS Marking

Additional References for Class-Based Ethernet CoS Matching and Marking

Related Documents

Technical Assistance

Feature Information for Class-Based Ethernet CoS Matching & Marking

Was this Document Helpful?

Contact Cisco