The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
The Web Cache Communication Protocol (WCCP) is a Cisco-developed content-routing technology that intercepts IP packets and redirects those packets to a destination other than that specified in the IP packet. Typically the packets are redirected from their destination web server on the Internet to a content engine that is local to the client. In some WCCP deployment scenarios, redirection of traffic may also be required from the web server to the client. WCCP enables you to integrate content engines into your network infrastructure.
Cisco IOS Release 12.1 and later releases allow the use of either WCCP Version 1 (WCCPv1) or Version 2 (WCCPv2).
The tasks in this document assume that you have already configured content engines on your network. For specific information on hardware and network planning associated with Cisco Content Engines and WCCP, see the Cisco Content Engines documentation at the following URL:
http://www.cisco.com/univercd/cc/td/doc/product/webscale/content/index.htm
Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.
The following limitations apply to WCCPv2:
The following limitation apply to Cisco Catalyst 6500 series switches:
When WCCP is using mask assignment, any redirect list is merged with the mask information from the appliance and the resulting merged ACL is passed down to the Catalyst 6500 series switch or Cisco 7600 series router hardware. Only Permit or Deny ACL entries from the redirect list in which the protocol is IP or exactly matches the service group protocol are merged with the mask information from the appliance.
The following restrictions apply to the redirect-list ACL:
If the redirect ACL does not meet the restrictions shown, the system will log the following error message:
WCCP-3-BADACE: Service <service group>, invalid access-list entry (seq:<sequence>, reason:<reason>)
WCCP continues to redirect packets, but the redirection is carried out in software (NetFlow Switching) until the access list is adjusted.
WCCP uses Cisco Content Engines (or other content engines running WCCP) to localize web traffic patterns in the network, enabling content requests to be fulfilled locally. Traffic localization reduces transmission costs and download time.
WCCP enables routing platforms to transparently redirect content requests. The main benefit of transparent redirection is that users need not configure their browsers to use a web proxy. Instead, they can use the target URL to request content, and have their requests automatically redirected to a content engine. The word "transparent" in this case means that the end user does not know that a requested file (such as a web page) came from the content engine instead of from the originally specified server.
A content engine receiving a request attempts to service it from its own local cache. If the requested information is not present, the content engine issues its own request to the originally targeted server to get the required information. A content engine retrieving the requested information forwards it to the requesting client and caches it to fulfill future requests, thus maximizing download performance and substantially reducing transmission costs.
WCCP enables a series of content engines, called a content engine cluster, to provide content to a router or multiple routers. Network administrators can easily scale their content engines to manage heavy traffic loads through these clustering capabilities. Cisco clustering technology enables each cluster member to work in parallel, resulting in linear scalability. Clustering content engines greatly improves the scalability, redundancy, and availability of your caching solution. You can cluster up to 32 content engines to scale to your desired capacity.
The WCCP Version 2 feature provides several enhancements and features to the WCCP protocol, including:
Multiple routers can use WCCPv2 to service a content engine cluster. In WCCPv1, only one router could redirect content requests to a cluster. The figure below illustrates a sample configuration using multiple routers.
The subset of content engines within a cluster and routers connected to the cluster that are running the same service is known as a service group. Available services include TCP and UDP redirection.
In WCCPv1, the content engines were configured with the address of the single router. WCCPv2 requires that each content engine be aware of all the routers in the service group. To specify the addresses of all the routers in a service group, you must choose one of the following methods:
The multicast option is easier to configure because you need only specify a single address on each content engine. This option also allows you to add and remove routers from a service group dynamically, without needing to reconfigure the content engines with a different list of addresses each time.
The following sequence of events details how WCCPv2 configuration works:
WCCPv2 allows redirection of traffic other than HTTP (TCP port 80 traffic), including a variety of UDP and TCP traffic. WCCPv1 supported the redirection of HTTP (TCP port 80) traffic only. WCCPv2 supports the redirection of packets intended for other ports, including those used for proxy-web cache handling, File Transfer Protocol (FTP) caching, FTP proxy handling, web caching for ports other than 80, and Real Audio, video, and telephony applications.
To accommodate the various types of services available, WCCPv2 introduced the concept of multiple service groups. Service information is specified in the WCCP configuration commands using dynamic services identification numbers (such as 98) or a predefined service keyword (such as web-cache). This information is used to validate that service group members are all using or providing the same service.
The content engines in a service group specify traffic to be redirected by protocol (TCP or UDP) and up to eight source or destination ports. Each service group has a priority status assigned to it. The priority of a dynamic service is assigned by the content engine. The priority value is in the range of 0 to 255 where 0 is the lowest priority. The predefined web-cache service has an assigned priority of 240.
WCCPv2 allows multiple routers to be attached to a cluster of cache engines. The use of multiple routers in a service group allows for redundancy, interface aggregation, and distribution of the redirection load. WCCPv2 supports up to 32 routers per service group. Each service group is established and maintained independently.
WCCPv2 provides optional authentication that enables you to control which routers and content engines become part of the service group using passwords and the Hashed Message Authentication Code—Message Digest (HMAC MD5) standard. Shared-secret MD5 one-time authentication (set using the ip wccp [password [0 | 7] password] global configuration command) enables messages to be protected against interception, inspection, and replay.
If a content engine is unable to provide a requested object it has cached due to error or overload, the content engine will return the request to the router for onward transmission to the originally specified destination server. WCCPv2 provides a check on packets that determines which requests have been returned from the content engine unserviced. Using this information, the router can then forward the request to the originally targeted server (rather than attempting to resend the request to the content engine cluster). This process provides error handling transparency to clients.
Typical reasons why a content engine would reject packets and initiate the packet return feature include the following:
WCCPv2 can be used to adjust the load being offered to individual content engines to provide an effective use of the available resources while helping to ensure high quality of service (QoS) to the clients. WCCPv2 allows the designated content engine to adjust the load on a particular content engine and balance the load across the content engines in a cluster. WCCPv2 uses three techniques to perform load distribution:
The use of these hashing parameters prevents one content engine from being overloaded and reduces the potential for bottlenecking.
CPU usage may be very high when WCCP is enabled. The WCCP counters enable a determination of the bypass traffic directly on the router and can indicate whether the cause is high CPU usage due to enablement of WCCP. In some situations, 10 percent bypass traffic may be normal; in other situations, 10 percent may be high. However, any figure above 25 percent should prompt a closer investigation of what is occurring in the web cache.
If the counters suggest that the level of bypass traffic is high, the next step is to examine the bypass counters in the content engine and determine why the content engine is choosing to bypass the traffic. You can log in to the content engine console and use the CLI to investigate further. The counters allow you to determine the percent of traffic being bypassed.
You can use the clear ipv6 wccpservice-id command to remove the IPv6 WCCP statistics (counts) maintained on the router for a particular service.
You can use the clear wccp command to remove all (IPv4 and IPv6) WCCP statistics (counts) maintained on the router for a particular service.
You can use the show ipv6 wccp command to display the IPv6 WCCP global statistics (counts).
You can use the show wccp command to display all (IPv4 and IPv6) WCCP global statistics (counts).
Perform this task to configure WCCP.
Until you configure a WCCP service using the ip wccp{web-cache | service-number} global configuration command, WCCP is disabled on the router. The first use of a form of the ip wccp command enables WCCP. By default WCCPv2 is used for services, but you can use WCCPv1 functionality instead. To change the running version of WCCP from Version 2 to Version 1, or to return to WCCPv2 after an initial change, use the ip wccp version command in global configuration mode.
If a function is not allowed in WCCPv1, an error prompt will be printed to the screen. For example, if WCCPv1 is running on the router and you try to configure a dynamic service, the following message will be displayed: “WCCP V1 only supports the web-cache service.” The show ip wccp EXEC command will display the WCCP protocol version number that is running on your router.
Use the ip wccp web-cache password command to set a password for a router and the content engines in a service group. MD5 password security requires that each router and content engine that wants to join a service group be configured with the service group password. The password must be up to eight characters in length. Each content engine or router in the service group will authenticate the security component in a received WCCP packet immediately after validating the WCCP message header. Packets failing authentication will be discarded.
1. enable
2. configure terminal
3. ip wccp version {1 | 2}
4. ip wccp [vrf vrf-name] {web-cache | service-number} [group-address multicast-address] [redirect-list access-list] [group-list access-list] [password password [0 | 7] ]
5. interface type number
6. ip wccp [vrf vrf-name] {web-cache | service-number} redirect {in | out}
7. exit
8. interface type number
9. ip wccp redirect exclude in
1. enable
2. show ip wccp [vrf vrf-name] [web-cache |service-number] [detail view]
3. show ip interface
4. more system:running-config
The following example shows how to change the WCCP version from the default of WCCPv2 to WCCPv1, and enabling the web-cache service in WCCPv1:
Router# show ip wccp % WCCP version 2 is not enabled Router# configure terminal Router(config)# ip wccp version 1 Router(config)# end Router# show ip wccp % WCCP version 1 is not enabled Router# configure terminal Router(config)# ip wccp web-cache Router(config)# end Router# show ip wccp Global WCCP information: Router information: Router Identifier: 10.4.9.8 Protocol Version: 1.0 . . .
Router# configure terminal Router(config)# ip wccp web-cache group-address 224.1.1.100 password password1 Router(config)# ip wccp source-interface GigabitEthernet 0/1/0 Router(config)# ip wccp check services all Configures a check of all WCCP services. Router(config)# interface GigabitEthernet 0/1/0 Router(config-if)# ip wccp web-cache redirect in Router(config-if)# exit Router(config)# interface GigabitEthernet 0/2/0 Router(config-if)# ip wccp redirect exclude in Router(config-if)# exit
Related Topic |
Document Title |
---|---|
Cisco IOS commands |
|
QoS commands: complete command syntax, command modes, command history, defaults, usage guidelines, and examples |
Cisco IOS Quality of Service Solutions Command Reference |
MQC and information about attaching policy maps to interfaces |
"Applying QoS Features Using the MQC" module |
Additional match criteria that can be used for packet classification |
"Classifying Network Traffic" module |
Marking network traffic |
"Marking Network Traffic" module |
Standard |
Title |
---|---|
No new or modified standards are supported, and support for existing standards has not been modified. |
-- |
RFC |
Title |
---|---|
No new or modified RFCs are supported, and support for existing RFCs has not been modified. |
-- |
Description |
Link |
---|---|
The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password. |
The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.