Release Notes for Cisco Catalyst Center, Release 3.1.3
Available Languages
Bias-Free Language
The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
- US/Canada 800-553-2447
- Worldwide Support Phone Numbers
- All Tools
Feedback
Feedback
Catalyst Center, Release 3.1.3
Catalyst Center, Release 3.1.3
Cisco Catalyst Center is a powerful and comprehensive network management solution with functionality that spans all aspects of modern network management, including design, discovery, policy, provisioning, predictive analytics, intelligent monitoring, visibility, and compliance. Catalyst Center includes built-in automation and simplified workflows to help ensure efficiency and consistency in operations.
This document describes the features, limitations, and bugs for Catalyst Center, Release 3.1.3.
Note: Catalyst Center 3.1.3 is available in a phased rollout. Contact your Cisco sales representative to request access to this release.
Table 1. Change history to this document since its initial release
| Date |
Change |
Location |
| 2025-09-15 |
Added information about new features for Stealthwatch Security Analytics service on Cisco Catalyst. |
|
| 2025-09-11 |
Noted that Disaster Recovery is supported for only on-premises hardware appliances. |
|
| 2025-08-28 |
Noted that for virtual appliance deployments, neither Catalyst Center nor Cisco TAC can provide support for any issues, bugs, or unexpected behavior that occur in environments that use unsupported hypervisors. |
|
| 2025-08-21 |
Noted that when SFTP mode is disabled, Catalyst Center still returns ssh-rsa over port 22. However, there is no risk to Catalyst Center, as it does not support key-based client authentication. |
|
| 2025-08-13 |
Noted that Cisco User-Defined Network (UDN) workflows are no longer supported. |
|
| 2025-08-11 |
Added information about API rate limit limitations for Catalyst Center on ESXi. |
|
| 2025-08-08 |
Added guidelines about permission requirements for provisioning Stealthwatch Security Analytics on a device after an upgrade. |
|
| 2025-07-18 |
Added information about Catalyst Center on ESXi limitations. |
|
| 2025-06-30 |
Added information about the enhancements to the synchronization process for wireless controller configuration changes |
|
| 2025-06-16 |
Initial release |
_ |
Package versions in Catalyst Center 3.1.3
Table 2. Package versions in Catalyst Center 3.1.3
| Package name |
Release 3.1.3 |
| Release build version |
|
| Release version |
3.1.3-75710 |
| System updates |
|
| System |
3.1.59 |
| System Commons |
2.730.65945 |
| System Addons |
0.10.35 |
| Package updates |
|
| Access Control Application |
2.730.65945 |
| AI Endpoint Analytics |
1.11.1529 |
| AI Network Analytics |
4.0.30 |
| Application and Service Remediation |
3.0.20 |
| Application Hosting |
2.3.125041411 |
| Application Visibility and Policy |
2.730.117956 |
| Assurance |
3.130.480 |
| Assurance – Sensor |
3.130.416 |
| Automation - Intelligent Capture |
2.730.65945 |
| Automation – Sensor |
2.730.65945 |
| Catalyst Center API Catalog |
6.8.80-3 |
| Catalyst Center Gateway Service |
0.10.8 |
| Cisco Catalyst Center Global Search |
6.9.3 |
| Cisco Catalyst Center Platform |
6.9.39-3 |
| Cisco Catalyst Center UI |
3.5.138-3 |
| Cisco Identity Services Engine Bridge |
3.130.14 |
| Cloud Connectivity |
6.10.8 |
| Cloud Connectivity - Contextual Content |
7.0.7 |
| Cloud Connectivity – Digestor |
7.0.4 |
| Core Platform |
0.10.162-3 |
| Disaster Recovery |
2.730.365227 Note: This package is available only for the on-premises hardware appliance, not for the virtual appliance. |
| DxHub Cloud Connectivity |
6.10.21 |
| Group Based Policy Analytics |
3.130.15 |
| Identity and Access Management |
5.4.36-3 |
| Identity and Access Management - UI |
5.4.23-1 |
| Multiple Cisco Catalyst Center |
2.730.65945 |
| Network Controller Platform |
2.730.65945 |
| Network Data Platform - Base Analytics |
3.130.150390 |
| Network Data Platform - Caching Infra |
6.6.9 |
| Network Data Platform – Core |
6.6.118 |
| Network Data Platform - Ingestion Infra |
6.6.10 |
| Network Data Platform - Manager |
6.6.100 |
| Network Data Platform - Pipeline Infra |
6.6.119 |
| Network Data Platform - Storage Management |
6.6.38 |
| Platform Refresh |
1.2.90 |
| RCA-Scripts Package |
0.5.6 |
| Rogue and aWIPS |
3.1.57 |
| SD Access |
2.730.65945 |
| SEA App |
2.730.685124 |
| Shared Managed Services |
0.10.14 |
| Stealthwatch Security Analytics |
2.730.1095371 |
| Support Services |
2.730.885298 |
| System Management Operations |
1.6.38 |
| Telemetry |
4.7.15-2 |
| Wide Area Bonjour |
2.730.755051 |
The Disaster Recovery witness is available as a separate OVA file for Catalyst Center. Its version number is 2.1.730.370045.
Catalyst Center
Table 3. New and changed features in Catalyst Center 3.1.3
| Product impact |
Feature |
Description |
| Base functionality |
Configure Parallel Redundancy Protocol |
This workflow helps you set up and manage Parallel Redundancy Protocol (PRP) channels, which are used to ensure high availability and zero packet loss in critical network systems. |
| Energy Management |
Catalyst Center’s Energy Management offers insights into energy consumption patterns. This enables more strategic energy usage, significantly reduces operational costs, and reduces carbon footprint, that contributes to environmental sustainability. |
|
| Role-based access control enhancements for wireless devices |
Catalyst Center supports site-based, role-based access control (SRBAC), which limits a user's scope of access to certain network sites. You must ensure you have access to the sites and devices while using the wireless provisioning workflows. |
|
| Security and industrial configurations |
You can view and edit these device configurations in Catalyst Center inventory: ● Security:SupportedforCiscoCatalyst9000SeriesSwitchesandCisco Catalyst IE switches. ● Industrialconfigurations:SupportedforCiscoCatalystIEswitches only. |
|
| Support for site-based, role-based access control |
You can create access groups that limits access to certain network sites. Access group is a combination of the role and site. The behavior of Catalyst Center features depends on the user role and site specified in the access group. |
|
| Validation enhancements for assigning sites between different parent sites |
In network hierarchy, you can move a site under a different parent site only when the new parent site shares the same network settings as the current parent site. The new parent site must have the same network profile as the site. |
|
| VLAN support for trunk ports |
Catalyst Center supports the configuration of the allowed and native VLAN values for each trunk port. |
|
| Ease of use |
Enhancements to discovery dashboard |
The discovery dashboard now has the option to monitor and manage all the scheduled network operations. |
| Enhancements to software image repository |
The software image repository is now enhanced with more options to check the status of the image updates, schedule the image update at a specific date and time, and download readiness report for the updates. |
Cisco Catalyst Assurance
Table 4. New and changed features in Cisco Catalyst Assurance 3.1.3
| Product impact |
Feature |
Description |
| Base functionality |
AFC support for 6-GHz radio frequency in AP 360 |
In the AP 360 window, under the Detail Information > RF tab, Radio 2 (6-GHz band) includes support for Automated Frequency Coordination (AFC). This feature helps to reduce interference between APs and other devices operating on 6-GHz radio frequency, and enables the use of Standard Power AP operations. |
| Site-based, role-based access control for Assurance dashboards |
Assurance supports site-based, role-based access control (SRBAC), which limits a user's scope of access to certain network sites. Based on the scope or site-based assignment, the user can access and view the Network dashboard, Client dashboard, Issues dashboard, Application health dashboard, Network services dashboard, AI-enhanced RRM dashboard, devices, and clients. Only new users assigned with site- and role-based access control have restricted access to their respective scope-based dashboards and widgets and can view only the limited number of devices, clients, network topology, global issues, and health score settings. |
|
| Ease of use |
Enhanced visibility into Cisco ISE authentication failures for wired and wireless clients |
Instead of logging in to the Cisco ISE GUI to view Cisco ISE authentication failure details for wired and wireless clients, you can now view the Cisco ISE authentication failure details in Assurance on the
●
Assurance > Health dashboard under the
Client tab,
●
Client 360 window,
●
Assurance > Issues and Events dashboard under the Events tab, and
●
Assurance > Health dashboard under the
Network Services > AAA tab.
|
| Contextual RCA for support bundle |
You can initiate a contextual root cause analysis (RCA) directly from the Activity Logs and also download the logs for provisioning failures. |
|
| Enhancement to ThousandEyes Enterprise Agent |
You can install and manage ThousandEyes Enterprise Agents from the Health > Application dashboard. |
Catalyst Center platform
Table 5. New and changed features in Catalyst Center platform 3.1.3
| Product impact |
Feature |
Description |
| Base functionality |
API Operations |
Catalyst Center platform supports new API operations. For more information, see “New and changed information” in the Cisco Catalyst Center Platform User Guide. For detailed information about the API operations, see the Cisco Catalyst Center APIs on Cisco DevNet. |
| Network Devices Report |
This Catalyst Center platform release supports a new Energy Management report template. Using this report template, you can retrieve a consolidated Energy Management report showing energy consumption, cost, carbon emission, and carbon intensity data of your network devices, providing complete visibility. For more information, see “Run a Network Devices Report” in the Cisco Catalyst Center Platform User Guide. |
Table 6. New and changed features in Catalyst Center Automation 3.1.3
| Product impact |
Feature |
Description |
| Base functionality |
Access point (AP) priming for Cisco Catalyst 9800 Series Wireless Controller |
AP priming for Cisco Catalyst 9800 Series Wireless Controller enables users to preconfigure an AP to join a specific wireless controller. This allows the AP to automatically join its preferred wireless controller upon bootup. |
| Cloning the profiles across multiple wireless controllers |
Catalyst Center supports cloning the existing profiles created for wireless controllers. This allows users to reuse the configurations across multiple controllers, reducing the time taken to manually recreate the settings. |
|
| Support for new APs for Wi-Fi 7 configuration |
Catalyst Center supports these APs for Cisco IOS XE Release 17.17.1 or later:
● Cisco Catalyst 9172H Series Access Points
● Cisco Catalyst 9172I Series Access Points
|
|
| Support for new country codes |
Catalyst Center supports new country codes for the Cisco Wireless Controllers and APs running Cisco IOS XE Release 17.17.1 or later. The radios within the APs are assigned to a specific regulatory domain at the factory. A country code enables you to specify a particular country of operation within that regulatory domain. For a complete list of country codes supported per product, see https://www.cisco.com/c/dam/assets/prod/wireless/wireless-compliance-tool/index.html. |
|
| Support for XOR on Cisco Catalyst 9176D1 Series APs and Cisco Catalyst 9176I Series APs |
Catalyst Center supports dual-band (XOR) between 2.4-GHz and 5-GHz radio modes on slot 0 for these APs when they're running Cisco IOS XE Release 17.17.1 or later:
● Cisco Catalyst 9176D1 Series Access Points
● Cisco Catalyst 9176I Series Access Points
Note: If the APs are running Cisco IOS XE Release 17.15.2, slot 0 supports only the 2.4 GHz band. |
|
| Ease of use
|
Enhancements to AFC integration with Standard Power Mode |
Catalyst Center supports configuring AP Geolocation Parameters through the AP configuration workflow. You can view and edit geo-location parameters for eligible access points, which are utilized for Automated Frequency Coordination (AFC). |
| Enhancements to Per-Device Configuration on Cisco Catalyst 9800 Series Wireless Controller |
The Per-Device Configuration feature on Catalyst Center is enhanced to customize more features and parameters for a Cisco Catalyst 9800 Series Wireless Controller running Cisco IOS XE Release 17.12 or later. |
|
| Enhancements to the AP configuration workflow |
The Configure Access Points workflow includes these AP configurations to support the Per-Device Configuration feature:
● VLAN tag
● DNS configuration
● LAN port parameters
● BSS color configuration
|
|
| Enhancements to the synchronization process for wireless controller configuration changes |
The synchronization process triggered by a wireless controller configuration change event is optimized to improve performance:
● In earlier releases, a wireless controller configuration change caused Catalyst Center to resynchronize the wireless controller and its associated APs. This synchronization included updating AP details such as their configuration, operational status, and other related data.
● Starting with this release, a wireless controller configuration change now triggers only the synchronization of the wireless controller. During this synchronization, the configuration and status of APs that are associated with the wireless controller are not updated.
|
Table 7. New and changed features in Cisco Software-Defined Access 3.1.3
| Product impact |
Feature |
Description |
| Base functionality |
Custom role for Cisco SD-Access fabric |
Catalyst Center supports the creation of custom roles with the SD-Access capability that allows users to create and manage Cisco SD-Access fabric. |
| Ease of use |
Enhancements to Layer 2 virtual network configurations in Cisco SD-Access fabric |
Layer 2 virtual network supports configuration of these attributes:
●
Resource Guard: Option to block or unblock the SSDP traffic in the Cisco SD-Access fabric.
●
Flood Access Tunnel: Enable or disable flood access tunnel for a Layer 2 virtual network.
●
Flooding Address Assignment: Option to choose between a shared or custom flooding address and configure the custom flooding address.
|
| Enhancements to site hierarchy changes in Cisco SD-Access fabric |
You can move a site under a new site if it is within the fabric. Movement of fabric sites to a new fabric or a site outside the fabric is not allowed. |
|
| Mapping transits to sites in Cisco SD-Access fabric network |
Associating a transit (SDA transit and IP transit) to a geographical site such as an area, building, or floor allows site users to efficiently manage the transits. |
Stealthwatch Security Analytics service
Table 8. New and changed features in Stealthwatch Security Analytics service on Catalyst Center 3.1.3
| Product impact |
Feature |
Description |
| Base functionality |
Custom role for Stealthwatch |
Catalyst Center allows you to create a custom role and choose the required permission for Stealthwatch to manage Stealthwatch Security Analytics. |
| Support for Visibility and Control of Configurations |
The Visibility and Control of Configurations feature is now supported for Stealthwatch Security Analytics. With enhanced visibility, you can enforce the previewing of device configurations before deploying them. With enhanced control, you can ensure only authentic and authorized configurations are provisioned onto your network devices through an IT Service Management (ITSM) check. |
Changes in behavior
Table 9. Deprecated features in Catalyst Center 3.1.3
| Feature |
Description |
| Cisco User-Defined Network |
Starting in August 2025, Cisco User Defined Network Plus replaces UDN for Catalyst Center as the supported UDN solution. As part of this change, these GUI workflows are no longer supported:
●
Provision > Service Catalog > Cisco User Defined Network
●
Provision > Cisco User Defined Network
●
Workflow > Configure Cisco UDN
|
| Learn Device Configuration workflow |
Starting in 3.1.3, Catalyst Center doesn't support the Learn Device Configuration workflow. To manage Cisco Catalyst 9800 Series Wireless Controllers with existing configurations, you can use the Per-Device Configuration feature. |
You can use the Cisco Bug Search Tool to search for a specific bug or to search for all resolved bugs in this release.
You can use the Cisco Bug Search Tool to search for a specific bug or to search for all open bugs in this release.
To search for a documented Cisco product issue, type in the browser: <bug_number> site:cisco.com
Table 10. Guidelines and limitations for Catalyst Center 3.1.3
| Feature |
|
Description |
| Guidelines |
||
| APs |
|
Starting with this release, a wireless controller configuration change triggers only a wireless controller synchronization. During this synchronization, Catalyst Center:
● collects the wireless controller-related configurations, but
● doesn't update the configuration and status of the APs associated with the wireless controller.
To view updated information for APs associated with the wireless controller (like AP status, new AP discovery, AP configuration, and so on), you must manually perform a full wireless controller synchronization. For a full synchronization, complete these steps: Step 1. On the Inventory window, select the wireless controller. Step 2. Choose Actions > Inventory > Resync Device. |
| Device onboarding |
|
For IE-3200-8P2S-E/A, IE-3200-8T2S-E/A, IE-3300-8P2S-E/A, and IE-3300-8T2S-E/A devices with Cisco IOS XE 17.8.1 or later, to avoid an increase in memory consumption:
● Ensure that the device is in install boot mode before upgrading it to Catalyst Center.
● Use the
no netconf-yang command to disable NETCONF.
|
| ssh-rsa as a host key algorithm |
|
Even when SFTP mode is disabled, Catalyst Center still returns ssh-rsa over port 22. However, there is no risk to Catalyst Center, as it does not support key-based client authentication. Any risk from ssh-rsa’s use of SHA-1 affects clients verifying the server, not the server itself. ssh-rsa is one of the public key algorithms specified in RFC 4253 for use in SSH for server host key authentication and user authentication. It indicates the use of the RSA algorithm for digital signatures. For ssh-rsa signatures, the RFC mandates the use of the SHA-1 hash algorithm for signing and verifying, as per the Digital Signature Standard (DSS) [FIPS-186-2]. With server authentication, the burden of risk associated with using the SHA-1 hashing employed by ssh-rsa falls on the client and not the server, because the client tries to establish the legitimacy of the server, which could be any host, not just Catalyst Center. With key-based client authentication, the burden of risk associated with using the SHA-1 hashing employed by ssh-rsa falls on the server and not the client, because the server tries to establish the identity of the client. Because Catalyst Center doesn't support key-based authentication, Catalyst Center is not subject to any risk with client authentication. |
| Stealthwatch Security Analytics |
|
If you are upgrading from an earlier release to 3.1.3, you must have Write permissions for Stealthwatch to provision Stealthwatch Security Analytics on a device. With only Read permissions, you can’t edit or provision the configurations. Update the permissions before or after the upgrade to enable editing and provisioning the configurations. |
| Limitations |
||
| APs |
|
In the Inventory window, if you add a wireless controller with associated Wi-Fi 7 APs that don't meet license requirements, Catalyst Center displays a dialog box with details of these APs. If these APs become unreachable later, Catalyst Center continues to list them in the dialog box. |
| Application telemetry |
|
With Catalyst Center, application telemetry is not supported for Cisco Catalyst 9500 Series switches. |
| Catalyst Center on ESXi |
|
● Catalyst Center 3.1.3 on ESXi supports all the features that Catalyst Center 2.3.7.x on ESXi supports except for these features:
◦ Wireless: Cisco Umbrella ◦ System Workflows: These backup and restore methods are not supported: ◦ Backup and restore using the VMware vSphere Client snapshot function. ◦ Backup and restore from the Catalyst Center hardware appliance to the Catalyst Center virtual appliance on ESXi. ◦ System Performance APIs: These APIs are not supported: ◦ /dna/intent/api/v1/diagnostics/system/performance ◦ /dna/intent/api/v1/diagnostics/system/performance/history
● The API rate limit policies that are documented in the official API documentation aren’t enforced. As a result, you might exceed the recommended API request limits without being automatically throttled or blocked by the system with an error response 429.
While exceeding the API rate limits is not recommended, it is unlikely to cause immediate service disruption or security vulnerabilities. However, excessive API usage could lead to:
◦ Performance degradation: High API request volumes could impact the overall performance of the Catalyst Center platform, potentially causing slower response times or temporary unavailability. ◦ Resource contention: Increased API activity could consume additional system resources, affecting other platform functions or user experiences. ◦ Unexpected behavior: In some cases, exceeding the API rate limits could trigger unexpected platform behavior or errors.
We recommend that you adhere to the documented API rate limit policies to ensure optimal platform performance and stability.
● For Group-Based Policy Analytics, the summary for the 24-hour and 12-hour Sankey charts isn't available in Catalyst Center on ESXi.
● The three-node HA is not supported for Catalyst Center running on ESXi. For information about the VMware vSphere implementation and requirements for creating and using a vSphere HA cluster, see the
VMware vSphere product documentation.
● Catalyst Center on ESXi does not support these VMware vSphere features:
◦ Fault tolerance ◦ Suspending and resuming VMs ◦ Cloning VMs ◦ Snapshot (as backup)
● To configure the Management interface and the Enterprise interface, manually create a virtual machine using the VMware vSphere UI and then configure both interfaces using either the Maglev Configuration wizard or the Install Configuration wizard. For more information, see "Deploy a Virtual Appliance" in the
Cisco Catalyst Center on ESXi Deployment Guide.
|
| Cisco AireOS Wireless Controller |
|
When you onboard a FIPS-enabled Cisco AireOS Wireless Controller to Catalyst Center, the device compliance checks may fail due to a mismatch in the NA server CA certificate. To resolve this issue, complete these steps: Step 1. From the Catalyst Center UI, download the NA server CA certificate. Use this URL to automatically download the certificate file: http://<Catalyst Center IP address>/ca/pem Note: Use the HTTP method to download the CA certificate file. Step 2. Download this certificate file to Cisco AireOS Wireless Controller.
● From the Cisco AireOS Wireless Controller main menu, choose
Commands > Download File.
● Choose the file type
NA-Serv-CA-Certificate.
● Choose the required transfer mode.
● Enter valid data for the required configurations and click
Download.
|
| In-product help |
|
● Online help and Interactive Help are available in light mode only and don't support dark mode.
|
Catalyst Center compatibility matrix
For information about devices—such as routers, switches, and wireless APs—and software releases supported by each application in Catalyst Center, see the Cisco Catalyst Center Compatibility Matrix.
Cisco SD-Access compatibility matrix
For information about Cisco SD-Access hardware and software support for Catalyst Center, see the Cisco Software-Defined Access Compatibility Matrix. This information is helpful for deploying Cisco SD-Access.
Compatible browsers
The Catalyst Center GUI is compatible with the following HTTPS-enabled browsers:
● Google Chrome: Version 93 or later.
● Mozilla Firefox: Version 92 or later.
Screen resolution:
● Minimum: 1368 x 768 pixels
● Recommended: 1920 x 1080 pixels
We recommend that the client systems you use to log in to Catalyst Center be equipped with 64-bit operating systems and browsers.
For information about upgrading your current release of Catalyst Center, see the Cisco Catalyst Center Upgrade Guide.
Before you upgrade, use the Validation Tool to perform an appliance health and upgrade readiness check for Catalyst Center. Choose the Appliance Infrastructure Status and Upgrade Readiness Status validation sets for running preupgrade checks. For more information, see "Use the Validation Tool" in the "Configure System Settings" chapter of the Cisco Catalyst Center Administrator Guide.
Catalyst Center scale
For Catalyst Center scale numbers, see the Cisco Catalyst Center Data Sheet.
Support for Cisco Connected Mobile Experiences
Catalyst Center supports Cisco Connected Mobile Experiences (CMX) Release 10.6.2 or later. Earlier versions of Cisco CMX are not supported.
Caution:
● While configuring the CMX settings, do not include the # symbol in the CMX admin password. The CMX integration fails if you include the # symbol in the CMX admin password.
● Catalyst Center validates the CMX TLS/SSL certificates. The Catalyst Center GUI provides an option to review and import CMX certificates to establish trust for new and existing CMX integrations. To avoid interruption of service between Catalyst Center and CMX, configure the CMX SSL/TLS certificates and import the CMX certificate to Catalyst Center Trusted Certificates before upgrading to Catalyst Center 3.1.3. After the upgrade, you can validate the CMX connection status under System > Settings > Cisco Spaces/CMX Servers. Self-signed server certificates that aren't signed by a certificate authority (CA) aren't trusted.
Support for the Web Content Accessibility Guidelines 2.1 standard
Catalyst Center supports the Web Content Accessibility Guidelines (WCAG) 2.1 standard for the AA conformance level, with these limitations:
Table 11. WCAG 2.1 standard for the AA conformance level and limitations
| WCAG success criterion |
Support |
Limitations |
| 1.2.4: Captions (Live) |
Not Supported |
— |
| 1.2.5: Audio Description (Prerecorded) |
Not Supported |
— |
| 1.3.4: Orientation |
Not Supported |
— |
| 1.3.5: Identify Input Purpose |
Supported |
— |
| 1.4.3: Contrast (Minimum) |
Supported |
— |
| 1.4.4: Resize Text |
Supported |
— |
| 1.4.5: Images of Text |
Supported |
— |
| 1.4.10: Reflow |
Supported |
— |
| 1.4.11: Non -Text Contrast |
Supported |
— |
| 1.4.12: Text Spacing |
Supported |
— |
| 1.4.13: Content on Hover or Focus |
Supported |
— |
| 2.4.5: Multiple Ways |
Supported |
— |
| 2.4.6: Headings and Labels |
Supported |
— |
| 2.4.11: Focus Appearance (Minimum) |
Supported |
— |
| 2.5.7: Dragging Movements |
Partially Supported |
Dashboard partially supports drag and drop due to third-party library limitations. |
| 2.5.8: Target Size (Minimum) |
Supported |
— |
| 3.1.2: Language of Parts |
Supported |
— |
| 3.2.3: Consistent Navigation |
Supported |
— |
| 3.2.4: Consistent Identification |
Supported |
— |
| 3.3.3: Error Suggestion |
Supported |
— |
| 3.3.4: Error Prevention (Legal, Financial, Data) |
Not Supported |
— |
| 3.1.2: Language of Parts |
Supported |
— |
| 3.2.3: Consistent Navigation |
Supported |
— |
| 3.2.4: Consistent Identification |
Supported |
— |
| 3.3.3: Error Suggestion |
Supported |
— |
| 3.3.4: Error Prevention (Legal, Financial, Data) |
Not Supported |
— |
Supported hardware appliances
Cisco delivers Catalyst Center in the form of a rack-mountable, physical appliance. These versions of the Catalyst Center appliance are available:
● Second generation
◦ 44-core appliance: DN2-HW-APL (Cisco UCS C220 M5)
◦ 44-core promotional appliance: DN2-HW-APL-U (Cisco UCS C220 M5)
◦ 56-core appliance: DN2-HW-APL-L (Cisco UCS C220 M5)
◦ 56-core promotional appliance: DN2-HW-APL-L-U (Cisco UCS C220 M5)
◦ 112-core appliance: DN2-HW-APL-XL (Cisco UCS C480 M5)
◦ 112-core promotional appliance: DN2-HW-APL-XL-U (Cisco UCS C480 M5)
● Third generation
◦ 32-core appliance: DN3-HW-APL (Cisco UCS C220 M6)
◦ 56-core appliance: DN3-HW-APL-L (Cisco UCS C220 M6)
◦ 80-core appliance: DN3-HW-APL-XL (Cisco UCS C240 M6)
Statement of volatility
For the statement of volatility for the physical appliances, see the Statement of Volatility for Cisco UCS Hardware.
Catalyst Center 3.1.3 is supported for deployment as a virtual appliance (VA) on VMware ESXi for on-premises environments. Neither Catalyst Center nor Cisco TAC can provide support for any issues, bugs, or unexpected behavior that occur in environments that use other hypervisors.
Supported firmware
Catalyst Center 3.1.3 has been validated only against these firmware:
● Cisco IMC Version 4.3(2.240077) for appliance model DN2-HW-APL, DN2-HW-APL-L, DN2-HW-APL-XL
● Cisco IMC Version 4.3(5.250030) for appliance model DN3-HW-APL, DN3-HW-APL-L, DN3-HW-APL-XL
Update the Cisco IMC firmware
To update your Cisco IMC firmware, first see the release notes for the corresponding release of Catalyst Center that you are installing. In the release notes, the “Supported Firmware” section shows the Cisco IMC firmware version for your Catalyst Center release.
Then, see the Cisco Host Upgrade Utility User Guide for instructions on updating the firmware.
In a three-node cluster configuration, we recommend that you shut down all three nodes in the cluster before updating the Cisco IMC firmware. However, you can upgrade the cluster nodes individually if that's what you prefer. See “Typical Cluster Node Operations” in the Cisco Catalyst Center High Availability Guide and follow the steps provided to shut down one or all of the nodes for maintenance.
Related resources
See Cisco Catalyst Center Documentation for additional documents relating to Catalyst Center.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.
© 2025 Cisco Systems, Inc. All rights reserved