VPN zwischen Sonicwall-Produkten und Cisco Security Appliance - Konfigurationsbeispiel

pix515e-635#show running-config
: Saved
:
PIX Version 6.3(5)

!--- Sets the hardware speed to auto on both interfaces.

interface ethernet0 auto
interface ethernet1 auto


!--- Specifies the inside and outside interfaces.

nameif ethernet0 outside security0
nameif ethernet1 inside security100

enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
hostname pix515e-635
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names


!--- Specifies the traffic that can pass through the IPsec tunnel.

access-list pixtosw permit ip 192.168.1.0 255.255.255.0 172.22.1.0 255.255.255.0

pager lines 24
mtu outside 1500
mtu inside 1500


!--- Sets the inside and outside IP addresses and subnet masks.

ip address outside 10.20.20.1 255.255.255.0
ip address inside 192.168.1.1 255.255.255.0

ip audit info action alarm
ip audit attack action alarm
pdm history enable
arp timeout 14400


!--- Instructs PIX to perform PAT on the IP address on the outside interface.

global (outside) 1 interface


!--- Specifies addresses to be exempt from NAT (traffic to be tunneled).

nat (inside) 0 access-list pixtosw


!--- Specifies which addresses should use NAT (all except those exempted).

nat (inside) 1 0.0.0.0 0.0.0.0 0 0


!--- Specifies the default route on the outside interface.

route outside 0.0.0.0 0.0.0.0 10.20.20.2 1

timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout sip-disconnect 0:02:00 sip-invite 0:03:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server TACACS+ max-failed-attempts 3
aaa-server TACACS+ deadtime 10
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
aaa-server LOCAL protocol local
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable


!--- Implicit permit for all packets that come from IPsec tunnels.

sysopt connection permit-ipsec


!--- PHASE 2 CONFIGURATION: !--- Defines the transform set for Phase 2 encryption and authentication. !--- Austinlab is the name of the transform set that uses aes-256 encryption !--- as well as the SHA1 hash algorithm for authentication.

crypto ipsec transform-set austinlab esp-aes-256 esp-sha-hmac


!--- Specifies IKE is used to establish the IPsec SAs for the map "maptosw".

crypto map maptosw 67 ipsec-isakmp


!--- Specifies the ACL "pixtosw" to use with this map
. 
crypto map maptosw 67 match address pixtosw


!--- Specifies the IPsec peer for this map.

crypto map maptosw 67 set peer 10.10.10.1


!--- Specifies the transform set to use.

crypto map maptosw 67 set transform-set austinlab


!--- Specifies the interface to use with this map.

crypto map maptosw interface outside


 !--- PHASE 1 CONFIGURATION !--- Specifies the interface to use for the IPsec tunnel.

isakmp enable outside


!--- Specifies the preshared key and the addresses to use with that key. !--- In this case only one address is used with the preshared key cisco123.

isakmp key ******** address 10.10.10.1 netmask 255.255.255.255


!--- Defines how the PIX identifies itself in !--- IKE negotiations (IP address in this case).

isakmp identity address


!--- These five commands specify the Phase 1 configuration settings !--- specific to this sample configuration.

isakmp policy 13 authentication pre-share
isakmp policy 13 encryption aes-256
isakmp policy 13 hash sha
isakmp policy 13 group 2
isakmp policy 13 lifetime 28800

telnet timeout 5
ssh timeout 5
console timeout 0
terminal width 80
Cryptochecksum:07a3815d59db9965b72c7d8a7aaf7f5f
: end
pix515e-635#

pix515-702#show running-config
: Saved
:
PIX Version 7.0(2)
names
!


!--- PIX 7 uses an interface configuration mode similar to Cisco IOS®. !--- This output configures the IP address, interface name, !--- and security level for interfaces Ethernet0 and Ethernet1.

interface Ethernet0
  nameif outside
  security-level 0
  ip address 10.20.20.1 255.255.255.0
!
interface Ethernet1
  nameif inside
  security-level 100
  ip address 192.168.1.1 255.255.255.0
!
interface Ethernet2
  shutdown
  no nameif
  no security-level
  no ip address
!
interface Ethernet3
  shutdown
  no nameif
  no security-level
  no ip address
!
interface Ethernet4
  shutdown
  no nameif
  no security-level
  no ip address
!
interface Ethernet5
  shutdown
  no nameif
  no security-level
  no ip address
!
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
hostname pix515-702
domain-name cisco.com
ftp mode passive


!--- Specifies the traffic that can pass through the IPsec tunnel.

access-list pixtosw extended permit ip 192.168.1.0 255.255.255.0 172.22.1.0 255.255.255.0
pager lines 24
mtu inside 1500
mtu outside 1500
no failover
monitor-interface inside
monitor-interface outside
no asdm history enable
arp timeout 14400


!--- Instructs PIX to perform PAT on the IP address on the outside interface.

global (outside) 1 interface


!--- Specifies addresses to be exempt from NAT (traffic to be tunneled).

nat (inside) 0 access-list pixtosw


!--- Specifies which addresses should use NAT (all except those exempted).

nat (inside) 1 0.0.0.0 0.0.0.0


!--- Specifies the default route on the outside interface.

route outside 0.0.0.0 0.0.0.0 10.20.20.2 1

timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00
timeout mgcp-pat 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp


!--- Implicit permit for all packets that come from IPsec tunnels.

sysopt connection permit-ipsec


 !--- PHASE 2 CONFIGURATION !--- Defines the transform set for Phase 2 encryption and authentication. !--- Austinlab is the name of the transform set that uses aes-256 encryption !--- as well as the SHA1 hash algorithm for authentication.

crypto ipsec transform-set austinlab esp-aes-256 esp-sha-hmac


!--- Specifies the ACL pixtosw to use with this map.

crypto map maptosw 67 match address pixtosw


!--- Specifies the IPsec peer for this map.

crypto map maptosw 67 set peer 10.10.10.1


!--- Specifies the transform set to use.

crypto map maptosw 67 set transform-set austinlab


!--- Specifies the interface to use with this map
.
crypto map maptosw interface outside


 !--- PHASE 1 CONFIGURATION !--- Defines how the PIX identifies itself in !--- IKE negotiations (IP address in this case).

isakmp identity address


!--- Specifies the interface to use for the IPsec tunnel.

isakmp enable outside


!--- These five commands specify the Phase 1 configuration !--- settings specific to this sample configuration.

isakmp policy 13 authentication pre-share
isakmp policy 13 encryption aes-256
isakmp policy 13 hash sha
isakmp policy 13 group 2
isakmp policy 13 lifetime 28800

telnet timeout 5
ssh timeout 5
console timeout 0


!--- These three lines set the IPsec attributes for the tunnel to the !--- remote peer. This is where the preshared key is defined for Phase 1 and the !--- IPsec tunnel type is set to site-to-site.

tunnel-group 10.10.10.1 type ipsec-l2l
tunnel-group 10.10.10.1 ipsec-attributes
pre-shared-key *

Cryptochecksum:092b6fc5370e2ef0cf07c2bc10f1d44a
: end
pix515-702#

pix515e-635#show running-config
: Saved
:
PIX Version 6.3(5)

!--- Sets the hardware speed to auto on both interfaces.

interface ethernet0 auto
interface ethernet1 auto


!--- Specifies the inside and outside interfaces.

nameif ethernet0 outside security0
nameif ethernet1 inside security100         

enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
hostname pix515e-635
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names


!--- Specifies the traffic that can pass through the IPsec tunnel.

access-list pixtosw permit ip 192.168.1.0 255.255.255.0 172.22.1.0 255.255.255.0

pager lines 24
mtu outside 1500
mtu inside 1500


!--- Sets the inside and outside IP addresses and subnet masks.

ip address outside 10.20.20.1 255.255.255.0
ip address inside 192.168.1.1 255.255.255.0

ip audit info action alarm
ip audit attack action alarm
pdm history enable
arp timeout 14400


!--- Instructs PIX to perform PAT on the IP address on the outside interface.

global (outside) 1 interface


!--- Specifies addresses to be exempt from NAT (traffic to be tunneled).

nat (inside) 0 access-list pixtosw


!--- Specifies which addresses should use NAT (all except those exempted).

nat (inside) 1 0.0.0.0 0.0.0.0 0 0


!--- Specifies the default route on the outside interface.

route outside 0.0.0.0 0.0.0.0 10.20.20.2 1

timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout sip-disconnect 0:02:00 sip-invite 0:03:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server TACACS+ max-failed-attempts 3
aaa-server TACACS+ deadtime 10
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
aaa-server LOCAL protocol local
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable


!--- Implicit permit for all packets that come from IPsec tunnels.

sysopt connection permit-ipsec


 !--- PHASE 2 CONFIGURATION !--- Defines the transform set for Phase 2 encryption and authentication. !--- Austinlab is the name of the transform set that uses aes-256 encryption !--- as well as the SHA1 hash algorithm for authentication.

crypto ipsec transform-set austinlab esp-aes-256 esp-sha-hmac


!--- Creates the dynamic map ciscopix for the transform set.

crypto dynamic-map ciscopix 1 set transform-set austinlab


!--- Specifies the IKE that should be used to establish SAs !--- for the dynamic map.

crypto map dynmaptosw 66 ipsec-isakmp dynamic ciscopix


!--- Applies the settings above to the outside interface.

crypto map dynmaptosw interface outside


 !--- PHASE 1 CONFIGURATION !--- Specifies the interface to use for the IPsec tunnel
.
isakmp enable outside


!--- Specifies the preshared key and the addresses to use with that key. !--- In this case only one address is used as the preshared key "cisco123".

isakmp key ******** address 10.10.10.1 netmask 255.255.255.255


!--- Defines how the PIX identifies itself in !--- IKE negotiations (IP address in this case).

isakmp identity address


!--- These five commands specify the Phase 1 configuration settings !--- specific to this sample configuration.

isakmp policy 13 authentication pre-share
isakmp policy 13 encryption aes-256
isakmp policy 13 hash sha
isakmp policy 13 group 2
isakmp policy 13 lifetime 28800

telnet timeout 5
ssh timeout 5
console timeout 0
terminal width 80
Cryptochecksum:07a3815d59db9965b72c7d8a7aaf7f5f
: end
pix515e-635#

pix515-702#show running-config
: Saved
:
PIX Version 7.0(2)
names
!


!--- PIX 7 uses an interface configuration mode similar to Cisco IOS. !--- This output configures the IP address, interface name, and security level for !--- interfaces Ethernet0 and Ethernet1.

interface Ethernet0
  nameif outside
  security-level 0
  ip address 10.20.20.1 255.255.255.0
!
interface Ethernet1
  nameif inside
  security-level 100
  ip address 192.168.1.1 255.255.255.0
!
interface Ethernet2
  shutdown
  no nameif
  no security-level
  no ip address
!
interface Ethernet3
  shutdown
  no nameif
  no security-level
  no ip address
!
interface Ethernet4
  shutdown
  no nameif
  no security-level
  no ip address
!
interface Ethernet5
  shutdown
  no nameif
  no security-level
  no ip address
!
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
hostname pix515-702
domain-name cisco.com
ftp mode passive


!--- Specifies the traffic that can pass through the IPsec tunnel.

access-list pixtosw extended permit ip 192.168.1.0 255.255.255.0 172.22.1.0 255.255.255.0
pager lines 24
mtu inside 1500
mtu outside 1500
no failover
monitor-interface inside
monitor-interface outside
no asdm history enable
arp timeout 14400


!--- Instructs PIX to perform PAT on the IP address on the outside interface.

global (outside) 1 interface


!--- Specifies addresses to be exempt from NAT (traffic to be tunneled).

nat (inside) 0 access-list pixtosw


!--- Specifies which addresses should use NAT (all except those exempted).

nat (inside) 1 0.0.0.0 0.0.0.0


!--- Specifies the default route on the outside interface.

route outside 0.0.0.0 0.0.0.0 10.20.20.2 1

timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00
timeout mgcp-pat 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp


!--- Implicit permit for all packets that come from IPsec tunnels.

sysopt connection permit-ipsec


 !--- PHASE 2 CONFIGURATION !--- Defines the transform set for Phase 2 encryption and authentication. !--- Austinlab is the name of the transform set that uses aes-256 encryption !--- as well as the SHA1 hash algorithm for authentication.

crypto ipsec transform-set austinlab esp-aes-256 esp-sha-hmac


!--- Creates the dynamic map "ciscopix" for the defined transform set.

crypto dynamic-map ciscopix 1 set transform-set austinlab


!--- Specifies that IKE should be used to establish SAs !--- for the defined dynamic map.

crypto map dynmaptosw 66 ipsec-isakmp dynamic ciscopix


!--- Applies the settings to the outside interface.

crypto map dynmaptosw interface outside


 !--- PHASE 1 CONFIGURATION !--- Defines how the PIX identifies itself in !--- IKE negotiations (IP address in this case).

isakmp identity address


!--- Specifies the interface to use for the IPsec tunnel.

isakmp enable outside


!--- These five commands specify the Phase 1 configuration settings !--- specific to this sample configuration.

isakmp policy 13 authentication pre-share
isakmp policy 13 encryption aes-256
isakmp policy 13 hash sha
isakmp policy 13 group 2
isakmp policy 13 lifetime 28800

telnet timeout 5
ssh timeout 5
console timeout 0


!--- These three lines set the IPsec attributes for the tunnel to the !--- remote peer. This is where the preshared key is defined for Phase 1 and the !--- IPsec tunnel type is set to site-to-site.

tunnel-group 10.10.10.1 type ipsec-l2l
tunnel-group 10.10.10.1 ipsec-attributes
pre-shared-key *

Cryptochecksum:092b6fc5370e2ef0cf07c2bc10f1d44a
: end
pix515-702#

pix515e-635#show crypto isakmp sa
Total     : 1
Embryonic : 0
        dst               src        state     pending     created
      10.10.10.1       10.20.20.1    QM_IDLE         0           1
pix515e-635#



pix515e-635#show crypto ipsec sa


           interface: outside
           Crypto map tag: maptosw, local addr. 10.20.20.1

 local ident (addr/mask/prot/port): (192.168.1.0/255.255.255.0/0/0)
           remote ident (addr/mask/prot/port): (172.22.1.0/255.255.255.0/0/0)
           current_peer: 10.10.10.1:500
           PERMIT, flags={origin_is_acl,}
           #pkts encaps: 4, #pkts encrypt: 4, #pkts digest 4
           #pkts decaps: 4, #pkts decrypt: 4, #pkts verify 4
           #pkts compressed: 0, #pkts decompressed: 0
           #pkts not compressed: 0, #pkts compr. failed: 0, #pkts decompress failed: 0
           #send errors 1, #recv errors 0

 local crypto endpt.: 10.20.20.1, remote crypto endpt.: 10.10.10.1
           path mtu 1500, ipsec overhead 72, media mtu 1500
           current outbound spi: ed0afa33

 inbound esp sas:
           spi: 0xac624692(2892121746)
           transform: esp-aes-256 esp-sha-hmac ,
           in use settings ={Tunnel, }
           slot: 0, conn id: 1, crypto map: maptosw
           sa timing: remaining key lifetime (k/sec): (4607999/28718)
           IV size: 16 bytes
           replay detection support: Y


           inbound ah sas:


           inbound pcp sas:


           outbound esp sas:
           spi: 0xed0afa33(3976919603)
           transform: esp-aes-256 esp-sha-hmac ,
           in use settings ={Tunnel, }
           slot: 0, conn id: 2, crypto map: maptosw
           sa timing: remaining key lifetime (k/sec): (4607999/28718)
           IV size: 16 bytes
           replay detection support: Y


           outbound ah sas:


           outbound pcp sas:

pix515e-635#

pix515-702#show crypto isakmp sa

 Active SA: 1
           Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
           Total IKE SA: 1

1 IKE Peer: 10.10.10.1
           Type : L2L Role : initiator
           Rekey : no State : MM_ACTIVE
           pix515-702#

pix515-702#show crypto ipsec sa
interface: outside
    Crypto map tag: maptosw, local addr: 10.20.20.1

 local ident (addr/mask/prot/port): (192.168.1.0/255.255.255.0/0/0)
           remote ident (addr/mask/prot/port): (172.22.1.0/255.255.255.0/0/0)
           current_peer: 10.10.10.1

 #pkts encaps: 5, #pkts encrypt: 5, #pkts digest: 5
           #pkts decaps: 5, #pkts decrypt: 5, #pkts verify: 5
           #pkts compressed: 0, #pkts decompressed: 0
           #pkts not compressed: 5, #pkts comp failed: 0, #pkts decomp failed: 0
           #send errors: 0, #recv errors: 0

 local crypto endpt.: 10.20.20.1, remote crypto endpt.: 10.10.10.1

 path mtu 1500, ipsec overhead 76, media mtu 1500
           current outbound spi: 2D006547

 inbound esp sas:
           spi: 0x309F7A33 (815757875)
           transform: esp-aes-256 esp-sha-hmac
           in use settings ={L2L, Tunnel, }
           slot: 0, conn_id: 1, crypto-map: maptosw
           sa timing: remaining key lifetime (kB/sec): (4274999/28739)
           IV size: 16 bytes
           replay detection support: Y
           outbound esp sas:
           spi: 0x2D006547 (755000647)
           transform: esp-aes-256 esp-sha-hmac
           in use settings ={L2L, Tunnel, }
           slot: 0, conn_id: 1, crypto-map: maptosw
           sa timing: remaining key lifetime (kB/sec): (4274999/28737)
           IV size: 16 bytes
           replay detection support: Y

pix515-702#

pix515e-635#show crypto isakmp sa
Total     : 1
Embryonic : 0
        dst               src        state     pending     created
      10.20.20.1       10.10.10.1    QM_IDLE         0           1

pix515e-635#show crypto ipsec sa


           interface: outside
           Crypto map tag: dynmaptosw, local addr. 10.20.20.1

 local ident (addr/mask/prot/port): (192.168.1.0/255.255.255.0/0/0)
           remote ident (addr/mask/prot/port): (172.22.1.0/255.255.255.0/0/0)
           current_peer: 10.10.10.1:500
           PERMIT, flags={}
           #pkts encaps: 0, #pkts encrypt: 0, #pkts digest 0
           #pkts decaps: 0, #pkts decrypt: 0, #pkts verify 0
           #pkts compressed: 0, #pkts decompressed: 0
           #pkts not compressed: 0, #pkts compr. failed: 0, #pkts decompress failed: 0
           #send errors 0, #recv errors 0

 local crypto endpt.: 10.20.20.1, remote crypto endpt.: 10.10.10.1
           path mtu 1500, ipsec overhead 72, media mtu 1500
           current outbound spi: efb1149d

 inbound esp sas:
           spi: 0x2ad2c13c(718455100)
           transform: esp-aes-256 esp-sha-hmac ,
           in use settings ={Tunnel, }
           slot: 0, conn id: 2, crypto map: dynmaptosw
           sa timing: remaining key lifetime (k/sec): (4608000/28736)
           IV size: 16 bytes
           replay detection support: Y


           inbound ah sas:


           inbound pcp sas:


           outbound esp sas:
           spi: 0xefb1149d(4021359773)
           transform: esp-aes-256 esp-sha-hmac ,
           in use settings ={Tunnel, }
           slot: 0, conn id: 1, crypto map: dynmaptosw
           sa timing: remaining key lifetime (k/sec): (4608000/28727)
           IV size: 16 bytes
           replay detection support: Y


           outbound ah sas:


           outbound pcp sas:

pix515e-635#

pix515-702#show crypto isakmp sa

 Active SA: 1
           Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
           Total IKE SA: 1

1 IKE Peer: 10.10.10.1
           Type : L2L Role : responder
           Rekey : no State : AM_ACTIVE
           pix515-702#

pix515-702#show crypto ipsec sa
           interface: outside
           Crypto map tag: ciscopix, local addr: 10.20.20.1

 local ident (addr/mask/prot/port): (192.168.1.0/255.255.255.0/0/0)
           remote ident (addr/mask/prot/port): (172.22.1.0/255.255.255.0/0/0)
           current_peer: 10.10.10.1

 #pkts encaps: 5, #pkts encrypt: 5, #pkts digest: 5
           #pkts decaps: 5, #pkts decrypt: 5, #pkts verify: 5
           #pkts compressed: 0, #pkts decompressed: 0
           #pkts not compressed: 5, #pkts comp failed: 0, #pkts decomp failed: 0
           #send errors: 0, #recv errors: 0

 local crypto endpt.: 10.20.20.1, remote crypto endpt.: 10.10.10.1

 path mtu 1500, ipsec overhead 76, media mtu 1500
           current outbound spi: D7E2F5FD

 inbound esp sas:
           spi: 0xDCBF6AD3 (3703532243)
           transform: esp-aes-256 esp-sha-hmac
           in use settings ={L2L, Tunnel, }
           slot: 0, conn_id: 1, crypto-map: ciscopix
           sa timing: remaining key lifetime (sec): 28703
           IV size: 16 bytes
           replay detection support: Y
           outbound esp sas:
           spi: 0xD7E2F5FD (3621975549)
           transform: esp-aes-256 esp-sha-hmac
           in use settings ={L2L, Tunnel, }
           slot: 0, conn_id: 1, crypto-map: ciscopix
           sa timing: remaining key lifetime (sec): 28701
           IV size: 16 bytes
           replay detection support: Y

pix515-702#