IPSec between PIX Firewall and Cisco VPN 3000 Concentrator with Overlapping Private Networks Configuration Example

Document ID: 23193

Introduction
Prerequisites
      Requirements
      Components Used
      Conventions
Configure
      Network Diagram
      Configurations
Verify
      PIX
      VPN Concentrator
Troubleshoot
      Troubleshooting Commands
NetPro Discussion Forums - Featured Conversations
Related Information

Introduction

This document describes how to configure the Cisco Secure PIX Firewall in a site-to-site IPSec VPN with overlapping private network addresses behind VPN gateways. The enhanced Network Address Translation (NAT) feature introduced in PIX 6.2 is used in this example to translate the overlapping networks on each side of the IPSec VPN tunnel to non-overlapping address spaces.

Prerequisites

Requirements

There are no specific requirements for this document.

Components Used

The information in this document is based on these software and hardware versions:

Cisco Secure PIX Firewall 506 with software version 6.3(3)
VPN 3030 Concentrator with software version 4.1(5)

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.

Conventions

For more information on document conventions, refer to Cisco Technical Tips Conventions.

Configure

In this section, you are presented with the information to configure the features described in this document.

Note: To find additional information on the commands used in this document, use the Command Lookup Tool ( registered customers only) .

Network Diagram

This document uses the network setup shown in this diagram.

Both Private_LAN1 and Private_LAN2 have an IP subnet of 192.168.4.0/24. This simulates the overlapping address space behind each side of the IPSec tunnel. The VPN 3000 Concentrator is used here as one example of a concentrator which does not have the functionality of NAT over VPN traffic.

In this example, the PIX performs a bi-directional translation so that the two private LANs can communicate over the IPSec tunnel. The translation means that Private_LAN1 "sees" Private_LAN2 as 10.1.1.0/24 through the IPSec tunnel, and Private_LAN2 "sees" Private_LAN1 as 20.1.1.0/24 through the IPSec tunnel.

Configurations

PIX

P520-1(config)#show run
: Saved
:
PIX Version 6.3(3)
interface ethernet0 auto
interface ethernet1 auto
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
hostname P520-1
domain-name bru-ch.com
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names   

!--- Defines IPSec interesting traffic.
!--- Note that the host behind PIX communicates
!--- to Private_LAN1 using 10.1.1.0/24.
!--- When the packets arrive at the PIX, they are first  
!--- translated to 192.168.4.0/24 and then encrypted by IPSec.

access-list 101 permit ip 20.1.1.0 255.255.255.0 192.168.4.0 255.255.255.0 
pager lines 24
mtu outside 1500
mtu inside 1500
ip address outside 172.16.172.34 255.255.255.0
ip address inside 192.168.4.4 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
pdm history enable
arp timeout 14400

!--- Static translation defined to translate Private_LAN2
!--- from 192.168.4.0/24 to 10.1.1.0/24.

static (outside,inside) 10.1.1.0 192.168.4.0 netmask 255.255.255.0 0 0

!--- Static translation defined to translate Private_LAN1 
!--- from 192.168.4.0/24 to 20.1.1.0/24.
!--- Note that this translation is used for both 
!--- VPN and Internet traffic from Private_LAN1.
!--- A routable global IP address range, or an extra NAT 
!--- at the ISP router (in front of PIX), is 
!--- required if Private_LAN1 also needs internal access.

static (inside,outside) 20.1.1.0 192.168.4.0 netmask 255.255.255.0 0 0
route outside 0.0.0.0 0.0.0.0 172.16.172.55 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+ 
aaa-server RADIUS protocol radius 
aaa-server LOCAL protocol local 
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec

!--- Defines IPSec encryption and authentication algorithms.

crypto ipsec transform-set myset esp-des esp-md5-hmac 

!--- Defines crypto map.

crypto map vpn 10 ipsec-isakmp
crypto map vpn 10 match address 101
crypto map vpn 10 set peer 172.16.172.55
crypto map vpn 10 set transform-set myset

!--- Apply crypto map on the outside interface.

crypto map vpn interface outside
isakmp enable outside

!--- Defines pre-shared secret (cisco123) used for IKE authentication.

isakmp key ******** address 172.16.172.55 netmask 255.255.255.255 
isakmp identity address

!--- Defines ISAKMP policy.

isakmp policy 1 authentication pre-share
isakmp policy 1 encryption des
isakmp policy 1 hash md5
isakmp policy 1 group 1
isakmp policy 1 lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
terminal width 80
Cryptochecksum:6cc25fc2fea20958dfe74c1fca45ada2
: end

VPN 3000 Concentrator LAN-to-LAN Tunnel Configuration

For the destination address 20.1.1.0 /24 (Private_LAN1) you need to have a static route on the VPN 3000. To do, select Configuration > System > IP Routing > Static Routes and choose Add. Once you are done filling out the fields, click Add.

Use the settings in these images to configure your VPN 3000 Concentrator.

Verify

This section provides information you can use to confirm your configuration is working properly.

Certain show commands are supported by the Output Interpreter Tool ( registered customers only) , which allows you to view an analysis of show command output.

show crypto isakmp sa - Display all current Internet Key Exchange (IKE) security associations (SAs) at a peer.
show crypto isakmp sa detail - Display the details of all current IKE SAs at a peer.
show crypto ipsec sa - Displays the settings used by current SAs.
show xlate detail - Displays translation slot information.

PIX

P520-1(config)# 
P520-1(config)#show crypto isakmp sa
Total     : 1
Embryonic : 0
        dst               src        state     pending     created
   172.16.172.55    172.16.172.34    QM_IDLE         0           1

P520-1(config)#show crypto isakmp sa detail
Total     : 1
Embryonic : 0
         Local            Remote          Encr Hash    Auth  State      Lifetime
   172.16.172.34:500    172.16.172.55:500  des  md5     psk QM_IDLE       86211
P520-1(config)# 

P520-1(config)#show crypto ipsec sa


interface: outside
    Crypto map tag: vpn, local addr. 172.16.172.34

   local  ident (addr/mask/prot/port): (20.1.1.0/255.255.255.0/0/0)
   remote ident (addr/mask/prot/port): (192.168.4.0/255.255.255.0/0/0)
   current_peer: 172.16.172.55:500
     PERMIT, flags={origin_is_acl,}
    #pkts encaps: 4, #pkts encrypt: 4, #pkts digest 4
    #pkts decaps: 4, #pkts decrypt: 4, #pkts verify 4
    #pkts compressed: 0, #pkts decompressed: 0
    #pkts not compressed: 0, #pkts compr. failed: 0, #pkts decompress failed: 0
    #send errors 1, #recv errors 0

     local crypto endpt.: 172.16.172.34, remote crypto endpt.: 172.16.172.55
     path mtu 1500, ipsec overhead 56, media mtu 1500
     current outbound spi: 734575cb

     inbound esp sas:
      spi: 0xe028850d(3760751885)
        transform: esp-des esp-md5-hmac ,
        in use settings ={Tunnel, }
        slot: 0, conn id: 1, crypto map: vpn
        sa timing: remaining key lifetime (k/sec): (4607999/28751)
        IV size: 8 bytes
        replay detection support: Y


    inbound ah sas:


     inbound pcp sas:


     outbound esp sas:
      spi: 0x734575cb(1933931979)
        transform: esp-des esp-md5-hmac ,
        in use settings ={Tunnel, }
        slot: 0, conn id: 2, crypto map: vpn
        sa timing: remaining key lifetime (k/sec): (4607999/28751)
        IV size: 8 bytes
        replay detection support: Y


     outbound ah sas:

P520-1(config)#show xlate detail
2 in use, 2 most used
Flags: D - DNS, d - dump, I - identity, i - inside, n - no random,
       o - outside, r - portmap, s - static
NAT from inside:192.168.4.1 to outside:20.1.1.1 flags s
NAT from outside:192.168.4.1 to inside:10.1.1.1 flags s

Use ping traffic to verify the tunnel. This debug icmp trace output collected on the PIX illustrates how the packets are translated by NAT.

P520-1(config)# debug icmp trace
ICMP trace on
Warning: this may cause problems on busy networks
P520-1(config)# 
1: ICMP echo-request from inside:192.168.4.1 to 10.1.1.1 ID=3060 seq=4391 length=80
2: ICMP echo-request: translating inside:192.168.4.1 to outside:20.1.1.1
3: ICMP echo-request: untranslating inside:10.1.1.1 to outside:192.168.4.1
4: ICMP echo-reply from outside:192.168.4.1 to 20.1.1.1 ID=3060 seq=4391 length=80
5: ICMP echo-reply: translating outside:192.168.4.1 to inside:10.1.1.1
6: ICMP echo-reply: untranslating outside:20.1.1.1 to inside:192.168.4.1
7: ICMP echo-request from inside:192.168.4.1 to 10.1.1.1 ID=3061 seq=4391 length=80
8: ICMP echo-request: translating inside:192.168.4.1 to outside:20.1.1.1
9: ICMP echo-request: untranslating inside:10.1.1.1 to outside:192.168.4.1
10: ICMP echo-reply from outside:192.168.4.1 to 20.1.1.1 ID=3061 seq=4391 length=80
11: ICMP echo-reply: translating outside:192.168.4.1 to inside:10.1.1.1
12: ICMP echo-reply: untranslating outside:20.1.1.1 to inside:192.168.4.1
13: ICMP echo-request from inside:192.168.4.1 to 10.1.1.1 ID=3062 seq=4391 length=80
14: ICMP echo-request: translating inside:192.168.4.1 to outside:20.1.1.1
15: ICMP echo-request: untranslating inside:10.1.1.1 to outside:192.168.4.1
16: ICMP echo-reply from outside:192.168.4.1 to 20.1.1.1 ID=3062 seq=4391 length=80
17: ICMP echo-reply: translating outside:192.168.4.1 to inside:10.1.1.1
18: ICMP echo-reply: untranslating outside:20.1.1.1 to inside:192.168.4.1
19: ICMP echo-request from inside:192.168.4.1 to 10.1.1.1 ID=3063 seq=4391 length=80
20: ICMP echo-request: translating inside:192.168.4.1 to outside:20.1.1.1
21: ICMP echo-request: untranslating inside:10.1.1.1 to outside:192.168.4.1
22: ICMP echo-reply from outside:192.168.4.1 to 20.1.1.1 ID=3063 seq=4391 length=80
23: ICMP echo-reply: translating outside:192.168.4.1 to inside:10.1.1.1
24: ICMP echo-reply: untranslating outside:20.1.1.1 to inside:192.168.4.1
25: ICMP echo-request from inside:192.168.4.1 to 10.1.1.1 ID=3064 seq=4391 length=80
26: ICMP echo-request: translating inside:192.168.4.1 to outside:20.1.1.1
27: ICMP echo-request: untranslating inside:10.1.1.1 to outside:192.168.4.1
28: ICMP echo-reply from outside:192.168.4.1 to 20.1.1.1 ID=3064 seq=4391 length=80
29: ICMP echo-reply: translating outside:192.168.4.1 to inside:10.1.1.1
30: ICMP echo-reply: untranslating outside:20.1.1.1 to inside:192.168.4.1
P520-1(config)#

VPN Concentrator

Select Monitoring > Sessions > Detail to verify your VPN 3000 Concentrator configuration.

Troubleshoot

This section provides information you can use to troubleshoot your configuration. Additional information on troubleshooting can be found in the following documents:

Troubleshooting Commands

Certain show commands are supported by the Output Interpreter Tool ( registered customers only) , which allows you to view an analysis of show command output.

Note: Before issuing debug commands, please see Important Information on Debug Commands.

This output demonstrates a working debug of the IKE negotiation. Shown here are the outputs of the debug crypto isakmp and debug crypto ipsec commands.

P520-1(config)#show debug
debug crypto ipsec 1
debug crypto isakmp 1
P520-1(config)# 
ISAKMP (0): beginning Main Mode exchange

crypto_isakmp_process_block:src:172.16.172.55, dest:172.16.172.34 spt:500 dpt:500
OAK_MM exchange
ISAKMP (0): processing SA payload. message ID = 0

ISAKMP (0): Checking ISAKMP transform 1 against priority 1 policy
ISAKMP:      encryption DES-CBC
ISAKMP:      hash MD5
ISAKMP:      default group 1
ISAKMP:      auth pre-share
ISAKMP:      life type in seconds
ISAKMP:      life duration (VPI) of  0x0 0x1 0x51 0x80 
ISAKMP (0): atts are acceptable. Next payload is 0
ISAKMP (0): processing vendor id payload

ISAKMP (0): SA is doing pre-shared key authentication using id type ID_IPV4_ADDR
return status is IKMP_NO_ERROR
crypto_isakmp_process_block:src:172.16.172.55, dest:172.16.172.34 spt:500 dpt:500
OAK_MM exchange
ISAKMP (0): processing KE payload. message ID = 0
ISAKMP (0): processing NONCE payload. message ID = 0
ISAKMP (0): processing vendor id payload
ISAKMP (0): processing vendor id payload
ISAKMP (0): received xauth v6 vendor id
ISAKMP (0): processing vendor id payload
ISAKMP (0): speaking to another IOS box!
ISAKMP (0): processing vendor id payload
ISAKMP (0): speaking to a VPN3000 concentrator
ISAKMP (0): ID payload
        next-payload : 8
        type         : 1
        protocol     : 17
        port         : 500
        length       : 8
ISAKMP (0): Total payload length: 12
return status is IKMP_NO_ERROR
crypto_isakmp_process_block:src:172.16.172.55, dest:172.16.172.34 spt:500 dpt:500
OAK_MM exchange
ISAKMP (0): processing ID payload. message ID = 0
ISAKMP (0): processing HASH payload. message ID = 0
ISAKMP (0): processing vendor id payload
ISAKMP (0): remote peer supports dead peer detection
ISAKMP (0): SA has been authenticated

ISAKMP (0): beginning Quick Mode exchange, M-ID of -995061605:c4b0909bIPSEC
(key_engine): got a queue event...
IPSEC(spi_response): getting spi 0xe028850d(3760751885) for SA 
        from   172.16.172.55 to   172.16.172.34 for prot 3

return status is IKMP_NO_ERROR
ISAKMP (0): sending INITIAL_CONTACT notify
ISAKMP (0): sending NOTIFY message 24578 protocol 1
VPN Peer: ISAKMP: Added new peer: ip:172.16.172.55/500 Total VPN Peers:1
VPN Peer: ISAKMP: Peer ip:172.16.172.55/500 Ref cnt incremented to:1 Total 
VPN Peers:1
crypto_isakmp_process_block:src:172.16.172.55, dest:172.16.172.34 spt:500 dpt:500
OAK_QM exchange
oakley_process_quick_mode:
OAK_QM_IDLE
ISAKMP (0): processing SA payload. message ID = 3299905691
ISAKMP : Checking IPSec proposal 1
ISAKMP: transform 1, ESP_DES
ISAKMP:   attributes in transform:
ISAKMP:      SA life type in seconds
ISAKMP:      SA life duration (basic) of 28800
ISAKMP:      SA life type in kilobytes
ISAKMP:      SA life duration (VPI) of  0x0 0x46 0x50 0x0 
ISAKMP:      encaps is 1
ISAKMP:      authenticator is HMAC-MD5
ISAKMP (0): atts are acceptable.IPSEC(validate_proposal_request): proposal part #1,
  (key eng. msg.) dest= 172.16.172.55, src= 172.16.172.34, 
    dest_proxy= 192.168.4.0/255.255.255.0/0/0 (type=4), 
   src_proxy= 20.1.1.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac , 
    lifedur= 0s and 0kb, 
    spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x4

ISAKMP (0): processing NONCE payload. message ID = 3299905691
ISAKMP (0): processing ID payload. message ID = 3299905691
ISAKMP (0): processing ID payload. message ID = 3299905691
ISAKMP (0): Creating IPSec SAs
        inbound SA from   172.16.172.55 to   172.16.172.34 
        (proxy 192.168.4.0 to   20.1.1.0)
        has spi 3760751885 and conn_id 1 and flags 4
        lifetime of 28800 seconds
        lifetime of 4608000 kilobytes
        outbound SA from   172.16.172.34 to   172.16.172.55 
       (proxy        20.1.1.0 to     192.168.4.0)
        has spi 1933931979 and conn_id 2 and flags 4
        lifetime of 28800 seconds
        lifetime of 4608000 kilobytesIPSEC(key_engine): got a queue event...
IPSEC(initialize_sas): ,
  (key eng. msg.) dest= 172.16.172.34, src= 172.16.172.55, 
    dest_proxy= 20.1.1.0/255.255.255.0/0/0 (type=4), 
    src_proxy= 192.168.4.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac , 
    lifedur= 28800s and 4608000kb, 
    spi= 0xe028850d(3760751885), conn_id= 1, keysize= 0, flags= 0x4
IPSEC(initialize_sas): ,
  (key eng. msg.) src= 172.16.172.34, dest= 172.16.172.55, 
    src_proxy= 20.1.1.0/255.255.255.0/0/0 (type=4), 
    dest_proxy= 192.168.4.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-md5-hmac , 
    lifedur= 28800s and 4608000kb, 
    spi= 0x734575cb(1933931979), conn_id= 2, keysize= 0, flags= 0x4

VPN Peer: IPSEC: Peer ip:172.16.172.55/500 Ref cnt incremented to:2 Total VPN Peers:1
VPN Peer: IPSEC: Peer ip:172.16.172.55/500 Ref cnt incremented to:3 Total VPN Peers:1
return status is IKMP_NO_ERROR
P520-1(config)# 
P520-1(config)# 
crypto_isakmp_process_block:src:172.16.172.55, dest:172.16.172.34 spt:500 dpt:500
ISAKMP (0): processing NOTIFY payload 36136 protocol 1
        spi 0, message ID = 1690390088
ISAMKP (0): received DPD_R_U_THERE from peer 172.16.172.55
ISAKMP (0): sending NOTIFY message 36137 protocol 1
return status is IKMP_NO_ERR_NO_TRANS
P520-1(config)#

NetPro Discussion Forums - Featured Conversations

Networking Professionals Connection is a forum for networking professionals to share questions, suggestions, and information about networking solutions, products, and technologies. The featured links are some of the most recent conversations available in this technology.

NetPro Discussion Forums - Featured Conversations for VPN

Service Providers: VPN Service Architectures

Service Providers: Network Management

Virtual Private Networks: Security

Virtual Private Networks: General

Related Information

Updated: Jan 18, 2008

Document ID: 23193

Hierarchical Navigation

IPSec Negotiation/IKE Protocols