Document ID: 12966
The Cisco 1700, 2600, and 3600 Series Routers support the Asymmetric Digital Subscriber Line (ADSL) WAN Interface Card (WIC). All three platforms are configured the same, but there are differences in hardware and in the Cisco IOS® Software release required for each one. Throughout this document the Cisco 1700/2600/3600 are called the "Cisco ADSL WIC."
This sample configuration shows a Cisco ADSL WIC configured with AAL5SNAP routing and terminating on a Cisco 6400 Universal Access Concentrator (UAC). Both the Cisco ADSL WIC and the Cisco 6400 use an ip unnumbered interface. This type of interface is well-suited for situations in which the number of available IP subnets is restricted.
The asynchronous transfer mode (ATM) main interface does not support the ip unnumbered command; use ATM point-to-point subinterfaces.
The RFC1483 routing service connects subscribers to a Cisco 6400 using AAL5SNAP encapsulation to carry IP traffic over ATM. The Node Route Processor (NRP) routes the IP traffic as required.
There are no specific prerequisites for this document.
The information in this document is based on these software and hardware versions.
Cisco 6400 UAC-NRP IOS Software Release 12.1(3)DC1
Cisco 6400 UAC-NSP IOS Software Release 12.1(3)DB
Cisco 6130 DSLAM-NI2 IOS Software Release 12.1(5)DA
The information presented in this document was created from devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If you are working in a live network, ensure that you understand the potential impact of any command before using it.
To support the ADSL WIC on the Cisco 2600/3600, this hardware is required:
Cisco 2600 series router:
Chassis WIC slots
Cisco 3600 series router:
Note: For the Cisco 3600, these do not support the ADSL WIC:
To support the ADSL WIC, these minimum Cisco IOS Software releases are required:
Cisco IOS Software Release 12.1(5)YB (Plus versions only) on the Cisco 2600/3600.
Cisco IOS Software Release IOS 12.1(3)XJ or later (Plus versions or ADSL feature set only) on the Cisco 1700. The ADSL feature set is identified by "y7" in the image name. For example, c1700-sy7-mz.121-3.XJ.bin.
Note: When you download the image for the Cisco 1700, make sure you select the image name of 1700. Do not download a 1720 or a 1750 image. The features do not support the ADSL WIC.
For more information on document conventions, refer to Cisco Technical Tips Conventions.
In this section, you are presented with the information to configure the features described in this document.
This document uses the network setup shown in this diagram.
This document uses the configurations shown here.
|Cisco ADSL WIC|
Current configuration: ! version 12.1 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R1 ip subnet-zero ! interface FastEthernet0 ip address 10.0.0.1 255.0.0.0 no ip directed-broadcast ! interface ATM0 no ip address no ip directed-broadcast no ip mroute-cache no atm ilmi-keepalive bundle-enable hold-queue 224 in ! interface ATM0.1 point-to-point ip unnumbered FastEthernet0 no ip directed-broadcast pvc 3/100 protocol ip 172.16.0.2 encapsulation aal5snap ! ip classless ip route 172.16.0.2 255.255.255.255 ATM0.1 no ip http server ! dialer-list 1 protocol ip permit ! line con 0 end
Current configuration: ! version 12.0 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname NRP ! redundancy main-cpu auto-sync standard no secondary console enable ip subnet-zero ! interface Loopback1 ip address 172.16.0.2 255.255.0.0 no ip directed-broadcast ! interface ATM0/0/0 no ip address no ip directed-broadcast no ip mroute-cache no atm ilmi-keepalive ! interface ATM0/0/0.3 point-to-point ip unnumbered Loopback1 no ip directed-broadcast no ip mroute-cache pvc 3/100 protocol ip 10.0.0.1 encapsulation aal5snap ! interface Ethernet0/0/1 no ip address no ip directed-broadcast ! interface Ethernet0/0/0 no ip address no ip directed-broadcast shutdown ! interface FastEthernet0/0/0 no ip address no ip directed-broadcast half-duplex ! ip classless ip route 10.0.0.1 255.255.255.255 ATM0/0/0.3 ip http server ! ! line con 0 transport input none line aux 0 line vty 0 4 login ! end
There is currently no verification procedure available for this configuration.
There is currently no specific troubleshooting information available for this configuration.
- Configuring the Cisco 6400
- Cisco ADSL Technical Tip
- DSL Technical Support
- RFC 1483
- Multiple Routed Protocols over ATM PVCs Using LLC Encapsulation
- Technical Support - Cisco Systems
|Updated: Feb 26, 2008||Document ID: 12966|