Document ID: 69583 |
Introduction
This document describes the relationship between Cisco Catalyst switches, Supervisor Engine modules and line cards.
Before You Begin
Requirements
There are no specific requirements for this document.
Components Used
Make certain that the version of software that you run supports the supervisor module and line card combination that you want to use. You can check software compatibility with the Software Advisor (registered customers only) tool.
Conventions
Refer to Cisco Technical Tips Conventions for more information on document conventions..
Cisco Catalyst 6500 series Supervisor Engine 720
These are the Supervisor Engine 720 features:
-
the Integrated 720-Gbps Switch Fabric
-
64-MB bootflash device or CompactFlash adapter with 512 MB CompactFlash card (WS-CF-UPG=):
-
64-MB bootflash device (sup-bootflash:) supported in all releases
-
WS-CF-UPG= (sup-bootdisk:) supported in Cisco IOS Software Release 12.2(18)SXE5 and later and Cisco IOS Software Release 12.2(18)SXF and later.
Supported Cards and the Minimum Software Requirements
This table lists the supervisor module with the supported Policy feature cards, MSFC cards and the minimum software requirements.
| Product | Supported Cards | Minimum Software Version |
|---|---|---|
| WS-SUP 720 | PFC 3A with 512-MB DRAM MSFC3 with 512-MB DRAM and 64-MB bootflash | 12.2(14)SX |
| WS-SUP720-3B | PFC3B with 512MB DRAM MSFC3 WITH 512 MB DRAM and 64MB bootflash | 12.2(17d)SXB1 |
| WS-SUP720-3BXL | PFC 3BXL with 1-GB DRAM MSFC3 with 1GB DRAM and 64-MB bootflash | 12.2(17b)SXA |
| VS-S720-10G-3C | Supervisor Engine 720-10GE with PFC3C | 12.2(33)SXH |
| VS-S720-10G-3CXL | Supervisor Engine 720-10GE with PFC3CXL | 12.2(33)SXH |
It is possible to upgrade the WS-SUP720-3B memory to 1-GB DRAM on the Supervisor Engine 720 and 1-GB DRAM on the MSFC3. In order to upgrade the memory, upgrade the Supervisor Engine 720, the MSFC3, and any DFC3-equipped switching modules.
Refer to Supervisor Engine 720 Switch Processor and Route Processor Memory Installation Note for memory upgrades.
Cisco Catalyst 6500 Series Supervisor Engine 32
The Supervisor Engine does not support some of these features:
-
Supervisor Engine 32 does not support Cisco IOS SLB.
-
Egress multicast replication
-
Multicast replication mode detection
-
All fabric configuration commands
Supported Cards and the Minimum Software Requirements
This table lists the supervisor module with the supported policy feature cards, MSFC cards and the minimum software requirements.
| Product | Supported Cards | Minimum Software Version |
|---|---|---|
| WS-SUP32-10GE-3B | PFC 3B with 256 DRAM for IP BASE SSH LAN ONLY image,512 MB RAM for all other images,256 MB bootflash. 10 Gigabit Ethernet ports MSFC2A with 64MB bootflash | 12.2(18)SFX |
| WS-SUP32-GE-3B | PFC 3B with 256 DRAM for IP BASE SSH LAN ONLY image,512 MB RAM for all other images,256 MB bootflash. MSFC2A with 64MB bootflash | 12.2(18)SFX |
Refer to Catalyst 6500 Series Switch Supervisor Engine Guide for hardware.
Cisco Catalyst 6500 Supervisor Engine 32 PISA
The Supervisor Engine 32 PISA offers these features:
-
Deep Packet Inspection and Application Awareness
-
Programmable Architecture
-
Integrated security
-
High availability
-
Enhanced manageability
-
Slot efficiency
-
Superior traffic management
Supported Cards and the Minimum Software Requirements
| Product | Supported Cards | Minimum Software Version |
|---|---|---|
| WS-S32-GE-PISA | Supervisor Engine 32 PISA with 8-Port Gigabit Ethernet and PFC3B | Cisco IOS® Software Release 12.2(18)ZY |
| WS-S32-10GE-PISA | Supervisor Engine 32 PISA with 2-Port 10 Gigabit Ethernet and PFC3B | Cisco IOS® Software Release 12.2(18)ZY |
Cisco Catalyst 6500 Series Supervisor Engine 2
Supported Cards and the Minimum Software Requirements
This table lists the supervisor module with the supported policy feature cards, MSFC cards and the minimum software requirements
| Product | Supported Cards | Minimum Software Version |
|---|---|---|
| WS-X6K-S2U-MSFC2 | PFC2 with256 MB DRAM,32 MB bootflash MSFC2 with 256 MB DRAM | 12.2(17d)SXB |
| WS-X6K-S2-MSFC2 | PFC2 with256 MB DRAM,32 MB bootflash MSFC2 with 256 MB DRAM | 12.2(17d)SXB |
In order to use WS-X6K-S2-MSFC2 with Cisco IOS Software Releases 12.2SX, upgrade the memory.
-
Refer to Catalyst 6000 Family MSFC/MSFC2 DRAM Upgrade Installation Note in order to upgrade MSFC2 DRAM.
-
Refer to Catalyst 6000 Family Supervisor Engine 2 DRAM Upgrade Installation Note in order to upgrade Supervisor Engine 2 DRAM.
-
Refer to Catalyst 6500 Series Supervisor Engine 2 Boot ROM and Bootflash Device Upgrade Installation Note in order to upgrade Supervisor Engine 2 Bootflash.
Note: Supervisor Engine 2 supports all GBICs supported by Cisco IOS Software Release 12.2(17d)SXB and later.
Gigabit Interface Converters (GBICs)
Supported Modules and Minimum Software Requirements
| Product | Minimum Software Version |
|---|---|
| WDM-GBIC-REC | 12.2(18)SXE |
| DWDM-GBIC | 12.2(17a)SX |
| CWDM-GBIC | 12.2(14)SX |
| WS-G5483 | 12.2(14)SX |
| WS-5484 | 12.2(14)SX |
| WS-5486 | 12.2(14)SX |
| WS-5487 | 12.2(14)SX |
10 Gigabit Ethernet Switching Modules
Supported Supervisor Engine and Minimum Software Requirements
| Product | Supported Supervisor Engine | Minimum Software Version |
|---|---|---|
| WS-X6748-SFP | SUP720 | 12.2(17d)SXB |
| WS-X6724-SFP | SUP720 | 12.2(17a)SX |
| WS-X6816-GBIC | SUP 720 SUP 2 | 12.2(14)SX in SUP720 12.2(17d)SXB in SUP 2 |
| WS-X6516A-GBIC | SUP 720 SUP 32 SUP 2 | 12.2(14)SX 12.2(18)SXF 12.2(17d)SXB |
| WS-6516-GBIC | SUP 720 SUP 32 SUP 2 | 12.2(14)SX 12.2(18)SXF 12.2(17d)SXB |
| WS-X6416-GBIC | SUP 720 SUP 32 SUP 2 | 12.2(14)SX 12.2(18)SXF 12.2(17d)SXB |
| WS-X6416-GE-MT | SUP 720 SUP 32 SUP 2 | 12.2(14)SX 12.2(18)SXF 12.2(17d)SXB |
| WS-X6316-GE-TX | SUP 720 SUP 32 SUP 2 | 12.2(14)SX 12.2(18)SXF 12.2(17d)SXB |
| WS-6408A-GBIC | SUP 720 SUP 32 SUP 2 | 12.2(14)SX 12.2(18)SXF 12.2(17d)SXB |
| WS-6408-GBIC | SUP 720 SUP 32 SUP 2 | 12.2(14)SX 12.2(18)SXF 12.2(17d)SXB |
10/100/1000 Ethernet Switching Modules
Supported Supervisor Engine and Minimum Software Requirements
| Product | Supported Supervisor Engine | Minimum Software Version |
|---|---|---|
| WS-X6748-GE-TX | SUP 720 | 12.2(17a)SX |
| WS-X6548-GE-TX | SUP 720 SUP 32 | 12.2(17a)SX 12.2(17d)SXB 12.2(18)SX |
| WS-X6548V-TX | SUP 32 SUP 2 | 12.2(18)SXF 12.2(17d)SXB |
| WS-X6548-GE-45AF | SUP 2 | 12.2(17d)SXB |
| WS-X6148-GE-TX | SUP720 SUP32 SUP 2 | 12.2(18)SXF 12.2(18)SXF 12.2(18)SXF 2 |
| WS-X6148-GE-45AF | SUP720 SUP32 SUP 2 | 12.2(18)SXF 12.2(18)SXF 12.2(18)SXF 2 |
| WS-X6148V-GE-TX | SUP720 SUP32 | 12.2(17a)SX 12.2(17d)SXB 12.2(18)SX |
| WS-X6516-GE-TX | SUP720 SUP32 SUP 2 | 12.2(14)SX 12.2(18)SXF 12.2(17d)SXB |
Features of 10/100/1000 Ethernet Switching Modules
-
ISL trunking
-
Jumbo frames
-
802.1Q tunneling
-
Traffic storm control
Fast Ethernet Switching Modules
Supported Supervisor Engine and Minimum Software Requirements
| Product | Supported Supervisor Engine | Minimum Software Version |
|---|---|---|
| WS-X6148-FE-SFP | SUP 720 SUP 32 SUP 2 | 12.2(18)SXF 12.2(18)SXF 12.2(18)SXF2 |
| WS-6524-100FX-MM | SUP 720 SUP 32 SUP 2 | 12.2(14)SX 12.2(18)SXF 12.2(17d)SXB |
| WS-X6324-100FX-SM | SUP 720 SUP 32 SUP 2 | 12.2(14)SX 12.2(18)SXF 12.2(17d)SXB |
| WS-X6324-100FX-MM | SUP 720 SUP 32 SUP 2 | 12.2(14)SX 12.2(18)SXF 12.2(17d)SXB |
| WS-6224-100FX-MT | SUP 720 SUP 32 SUP 2 | 12.2(14)SX 12.2(18)SXF 12.2(17d)SXB |
Ethernet/Fast Ethernet (10/100) Switching Modules
Supported Supervisor Engine and Minimum Software Requirements
| Product | Supported Supervisor Engine | Minimum Software Version |
|---|---|---|
| WS-X6548-RJ-45 | SUP 720 SUP 32 SUP 2 | 12.2(14)SX 12.2(18)SXF 12.2(17d)SXB |
| WS-6148X2-RJ-21 | SUP 720 SUP 32 SUP 2 | 12.2(14)SX 12.2(18)SXF 12.2(17d)SXB |
| WS-X6148X2-RJ-45 | SUP 720 SUP 32 SUP 2 | 12.2(18)SXF3 12.2(18)SXF3 12.2(18)SXF3 |
| WS-X6148X2-45AF | SUP 720 SUP 32 SUP 2 | 12.2(18)SXF3 12.2(18)SXF3 12.2(18)SXF3 |
| WS-X6196-RJ-21 | SUP 720 SUP 32 SUP 2 | 12.2(18)SXF3 12.2(18)SXF3 12.2(18)SXF3 |
| WS-X6196-21AF | SUP 720 SUP 32 SUP 2 | 12.2(18)SXF3 12.2(18)SXF3 12.2(18)SXF3 |
| WS-X6348-RJ-45 | SUP 720 SUP 32 SUP 2 | 12.2(14)SX 12.2(18)SXF 12.2(17d)SXB |
| WS-X6348-RJ-45V | SUP 720 SUP 32 SUP 2 | 12.2(14)SX 12.2(18)SXF 12.2(17d)SXB |
| WS-X6348-RJ-21V | SUP 720 SUP 32 SUP 2 | 12.2(14)SX 12.2(18)SXF 12.2(17d)SXB |
| WS-X6248-RJ-45 | SUP 720 SUP 32 SUP 2 | 12.2(14)SX 12.2(18)SXF 12.2(17d)SXB |
| WS-X6248-TEL | SUP 720 SUP 32 SUP 2 | 12.2(14)SX 12.2(18)SXF 12.2(17d)SXB |
| WS-X6148A-RJ-45 | SUP 720 SUP 32 | 12.2(18)SXF |
| WS-X6148A-45AF | SUP 720 SUP 32 | 12.2(18)SXF |
| WS-X6148-RJ-45 | SUP 720 SUP 32 | 12.2(17d)SXB 12.2(18)SXF |
| WS-X6148-RJ-45V | SUP 32 SUP 2 | 12.2(18)SXF 12.2(17d)SXB |
| WS-X6148-45AF | SUP 2 | 12.2 (17d)SXB |
| WS-X6148-RJ-21 | SUP 720 SUP 32 | 12.2(17d)SXB 12.2(18)SXF |
| WS-X6148-RJ-21V | SUP 32 SUP 2 | 12.2(18)SXF 12.2(17d)SXB |
| WS-X6148-21AF | SUP 2 | 12.2(17d)SXB |
Ethernet Switching Module
Supported Supervisor Engine and Minimum Software Requirements
| Product | Supported Supervisor Engine | Minimum Software Version |
|---|---|---|
| WS-X6024-10FL-MT | SUP 720 SUP 32 SUP 2 | 12.2(14)SX 12.2(18)SXF 12.2(17d)SXB |
Related Information
- Troubleshooting Hardware and Common Issues on Catalyst 6500/6000 Series Switches Running Cisco IOS System Software
- Common Error Messages on Catalyst 6500/6000 Series Switches Running Cisco IOS Software
- Troubleshooting Catalyst 6500/6000 Series Switches Running CatOS on the Supervisor Engine and Cisco IOS on the MSFC
- How to Determine the Type of Supervisor Module That Is Installed in Catalyst 6500/6000 Series Switches
- Memory/Flash Size Supported in Catalyst Switch Platforms
- How to Upgrade Software Images on Catalyst Switch Layer 3 Modules
| Updated: Feb 09, 2009 | Document ID: 69583 |
Feedback