Document ID: 5111
Contents
Introduction
Prerequisites
Requirements
Components Used
Conventions
Voice Hardware Compatibility Overview
Cisco 17xx, VG200, 26xx, and 2800 Platforms Matrix
Cisco ICS 7750, 36xx, 37xx, and 38xx Platforms Matrix
DSP Module Support Matrix
Catalyst Support Matrix
NetPro Discussion Forums - Featured Conversations
Related Information
Introduction
This document describes the relationship between routers, gateways, Cisco Catalyst switches, and voice network modules and cards.
Prerequisites
Requirements
There are no specific requirements for this document.
Components Used
-
To compare many of the network modules and interface cards, refer to the document Release Notes for the Cisco 3700 Series Modular Access Routers for Cisco IOS Release 12.3(4)XD.
-
Make certain that the version of Cisco IOS® System Software that you run supports the network module and interface card combination that you want to use. You can check Cisco IOS Software compatibility with the Software Advisor ( registered customers only) tool.
Conventions
Refer to Cisco Technical Tips Conventions for more information on document conventions.
Voice Hardware Compatibility Overview
The three tables in this section show the relationship between routers, gateways, Catalyst switches, and voice network modules and cards:
|
Router Model (right) |
|||
|---|---|---|---|
|
Voice Interface Card (VIC) (below) |
|||
|
No |
No |
No |
|
|
No |
No |
No |
|
|
No |
No |
No |
|
|
No |
No |
No |
|
|
NM-HDV-FARM |
No |
No |
No |
|
NM-HDV2 |
No |
No |
No |
|
No |
No |
No |
|
|
EVM-HD-8FXS/DID, EM-4BRI-NT/TE, EM-HDA-8FXS, EM-HDA-6FXO, EM-HDA-3FXS/4FXO |
No |
No |
No |
|
Voice Advanced Integration Module (AIM-VOICE) |
No |
No |
No |
|
Voice WAN Interface Cards (VWICs) without Network Modules |
Yes |
No |
Yes |
|
VICs without Network Modules |
No |
Yes |
Yes |
|
Switch Model |
Support Features |
||
|
Catalyst 4500/4000 Access Gateway Module |
WAN Interface Cards (WICs), VICs, Digital Signal Processors (DSPs), and IP phone inline power cards |
||
|
Catalyst 6500/6000 |
T1/E1 trunk modules, Foreign Exchange Station (FXS) modules, IP phone inline power cards, and the Communications Media Module |
||
-
1The NM-HD-1V and NM-HD-2V have feature parity with the NM-1V and NM-2V. However, there is currently no support on NM-1V and NM-2V for:
-
Trunked ATM Adaptation Layer 2 (AAL2) on analog ports
-
Universal Foreign Exchange Office (FXO) (VIC2-xFXO) voice cards with software-selectable Centralized Automated Message Accounting (CAMA)
-
Any VIC2 cards, such as VIC2-2BRI-NT/TE, VIC2-2FXS, VIC2-2E/M, and VIC-4FXS/Direct Inward Dial (DID) cards
-
The drop of DSPs on a Plain Old Telephone Service (POTS)-to-POTS call that stays within the network module
-
-
2The NM-HD-2VE interfaces have feature parity with the NM-HDV. However, there is currently no support on the NM-HD-xx for:
-
Modem relay
There is support for the G.168 echo cancellation (ECAN) in Cisco IOS Software Release 12.3(4)XD, Cisco IOS Software Release 12.3(7)T, and later. There is support for transcoding and conferencing services in Cisco IOS Software Release 12.3(8)T and later.
-
|
Router Model (right) |
VG200 3 |
2801 4 |
||||
|---|---|---|---|---|---|---|
|
VIC (below) |
||||||
|
Yes |
Yes |
Yes |
Yes |
No |
No |
|
|
Yes |
Yes |
Yes |
Yes |
No |
Yes |
|
|
No |
Yes |
Yes |
Yes |
No |
Yes |
|
|
No |
No |
No |
No |
No |
No |
|
|
NM-HDV-FARM |
Yes |
Yes5 |
Yes |
Yes |
No |
Yes |
|
NM-HDV2 |
No |
No |
Yes |
Yes |
No |
Yes |
|
No |
No |
Yes |
Yes |
No |
Yes |
|
|
EVM-HD-8FXS/DID, EM-4BRI-NT/TE, EM-HDA-8FXS, EM-HDA-6FXO, EM-HDA-3FXS/4FXO |
No |
No |
No |
No |
No |
Yes6 |
|
Voice Advanced Integration Module (AIM-VOICE) |
No |
Yes |
Yes |
Yes |
No |
No |
|
VWICs without Network Modules |
No |
Yes7 |
Yes7 |
Yes7 |
Yes |
Yes |
|
VICs without Network Modules |
No |
No |
No |
No |
Yes |
Yes |
|
Switch Model |
Support Features |
|||||
|
Catalyst 4500/4000 Access Gateway Module |
WICs, VICs, DSPs, and IP phone inline power cards |
|||||
|
Catalyst 6500/6000 |
T1/E1 trunk modules, FXS modules, IP phone inline power cards, and the Communications Media Module |
|||||
-
1The NM-HD-1V and NM-HD-2V have feature parity with the NM-1V and NM-2V. However, there is currently no support on NM-1V and NM-2V for:
-
Trunked ATM Adaptation Layer 2 (AAL2) on analog ports
-
Universal Foreign Exchange Office (FXO) (VIC2-xFXO) voice cards with software-selectable Centralized Automated Message Accounting (CAMA)
-
Any VIC2 cards, such as VIC2-2BRI-NT/TE, VIC2-2FXS, VIC2-2E/M, and VIC-4FXS/Direct Inward Dial (DID) cards
-
The drop of DSPs on a Plain Old Telephone Service (POTS)-to-POTS call that stays within the network module
-
-
2The NM-HD-2VE interfaces have feature parity with the NM-HDV. However, there is currently no support on the NM-HD-xx for:
-
Modem relay
There is support for the G.168 echo cancellation (ECAN) in Cisco IOS Software Release 12.3(4)XD, Cisco IOS Software Release 12.3(7)T, and later. There is support for transcoding and conferencing services in Cisco IOS Software Release 12.3(8)T and later.
-
-
3These products have reached end of sale. Refer to the End-of-Sale Announcement for the Cisco VG200 Access Gateway.
-
4 Slot 0 in 2801 can only be configured for voice, which means that PRI configurations with VWIC are not possible. However, configuration for channel associated signaling (CAS) is possible.
-
5There is support on the Cisco 2650 and 2651, but not on the 261x and 262x.
-
6Only the Cisco 2821 and 2851 models support the EVM-HD-8FXS/DID.
-
7VWICs without network modules have support on these platforms only if you have installed AIM-VOICE-30 or AIM-ATM-VOICE-30.
|
Router Model (right) |
||||||
|---|---|---|---|---|---|---|
|
VIC (below) |
||||||
|
No |
Yes |
Yes |
Yes |
Yes |
No |
|
|
No |
Yes |
Yes |
Yes |
Yes |
Yes |
|
|
No |
No |
Yes |
Yes |
Yes |
Yes |
|
|
Yes |
No |
No |
No |
No |
No |
|
|
NM-HDV-FARM |
No |
No |
Yes |
Yes |
Yes |
Yes |
|
NM-HDV2 |
No |
No |
No |
No |
Yes |
Yes |
|
No |
No |
Yes |
Yes |
Yes |
Yes |
|
|
EVM-HD-8FXS/DID, EM-4BRI-NT/TE, EM-HDA-8FXS, EM-HDA-6FXO, EM-HDA-3FXS/4FXO |
No |
No |
No |
No |
No |
Yes |
|
Voice Advanced Integration Module (AIM-VOICE) |
No |
No |
No |
Yes3 |
Yes |
No |
|
VWICs without Network Modules |
Yes |
No |
No |
No |
Yes4 |
Yes |
|
VICs without Network Modules |
Yes |
No |
No |
No |
No |
Yes |
|
Switch Model |
Support Features |
|||||
|
Catalyst 4500/4000 Access Gateway Module |
WICs, VICs, DSPs, and IP phone inline power cards |
|||||
|
Catalyst 6500/6000 |
T1/E1 trunk modules, FXS modules, IP phone inline power cards, and the Communications Media Module |
|||||
-
1The NM-HD-1V and NM-HD-2V have feature parity with the NM-1V and NM-2V. However, there is currently no support on NM-1V and NM-2V for:
-
Trunked ATM Adaptation Layer 2 (AAL2) on analog ports
-
Universal Foreign Exchange Office (FXO) (VIC2-xFXO) voice cards with software-selectable Centralized Automated Message Accounting (CAMA)
-
Any VIC2 cards, such as VIC2-2BRI-NT/TE, VIC2-2FXS, VIC2-2E/M, and VIC-4FXS/Direct Inward Dial (DID) cards
-
The drop of DSPs on a Plain Old Telephone Service (POTS)-to-POTS call that stays within the network module
-
-
2The NM-HD-2VE interfaces have feature parity with the NM-HDV. However, there is currently no support on the NM-HD-xx for:
-
Modem relay
There is support for the G.168 echo cancellation (ECAN) in Cisco IOS Software Release 12.3(4)XD, Cisco IOS Software Release 12.3(7)T, and later. There is support for transcoding and conferencing services in Cisco IOS Software Release 12.3(8)T and later.
-
-
3On the Cisco 3660, the AIM-VOICE-30 and AIM-ATM-VOICE-30 products only have support when there is also a multiservice interchange (MIX) daughter card installed.
-
4VWICs without network modules have support on these platforms only if you have installed AIM-VOICE-30 or AIM-ATM-VOICE-30.
Cisco 17xx, VG200, 26xx, and 2800 Platforms Matrix
The three tables in this section show the router or gateway models that support the voice network modules and the VICs. For more information on the modules and cards, which includes Cisco IOS Software support, click the link for the appropriate module or card.
|
Routers/Gateways |
|||||
|---|---|---|---|---|---|
|
Model |
VG200 1 |
||||
|
Voice Network Module (right) |
Not Used |
Not Used |
Not Used |
||
|
VIC (below) |
|||||
|
No |
Yes |
Yes |
Yes |
No |
|
|
No |
Yes |
Yes |
Yes |
No |
|
|
No |
Yes |
Yes |
Yes |
No |
|
|
No |
Yes |
Yes |
Yes |
No |
|
|
No |
No |
No |
Yes |
No |
|
|
No |
No |
Yes |
No |
No |
|
|
No |
No |
Yes |
Yes |
No |
|
|
No |
No |
No |
No |
No |
|
|
No |
No |
No |
No |
No |
|
|
No |
No |
No |
No |
No |
|
|
No |
No |
Yes |
No |
No |
|
|
VIC2-4FXO (FXO/CAMA) |
No |
No |
Yes |
No |
No |
|
VIC2-2FXO (FXO/CAMA) |
No |
No |
Yes |
No |
No |
|
VIC2-2FXS |
No |
No |
Yes |
No |
No |
|
VIC2-2E/M |
No |
No |
Yes |
No |
No |
|
VIC2-2BRI- NT/TE |
No |
No |
Yes |
No |
No |
|
VWIC-xMFT-E1 (with or without drop and insert [DI]) |
Yes3 |
No |
Yes |
No |
Yes |
|
VWIC-1MFT-G703 |
Yes3 |
No |
Yes |
No |
No |
|
Yes3 |
No |
Yes |
No |
Yes |
|
|
VWIC-xMFT-T1 (with or without DI) |
Yes3 |
No |
Yes |
No |
Yes |
Note:
-
1These products have reached end of sale. Refer to the End-of-Sale Announcement for the Cisco VG200 Access Gateway.
-
2The NM-HD-1V and NM-HD-2V have feature parity with the NM-1V and NM-2V. However, there is currently no support on NM-1V and NM-2V for:
-
Trunked AAL2 on analog ports
-
Universal FXO (VIC2-xFXO) voice cards with software-selectable CAMA
-
Any VIC2 cards, such as VIC2-2BRI-NT/TE, VIC2-2FXS, VIC2-2E/M, and VIC-4FXS/DID cards
-
The drop of DSPs on a POTS-to-POTS call that stays within the network module
-
-
3This configuration supports data applications only.
|
Routers/Gateways |
|||||||
|---|---|---|---|---|---|---|---|
|
Model |
|||||||
|
Voice Network Module (right) |
NM- HDV2 |
||||||
|
VIC (below) |
|||||||
|
Yes |
No |
Yes |
No |
No |
No |
No |
|
|
Yes |
No |
Yes |
No |
No |
No |
No |
|
|
Yes |
No |
Yes |
No |
No |
No |
No |
|
|
Yes |
No |
Yes |
No |
No |
No |
No |
|
|
Yes |
No |
Yes |
No |
No |
No |
No |
|
|
Yes |
No |
Yes |
No |
No |
No |
No |
|
|
Yes |
No |
Yes |
Yes |
Yes |
No |
Yes |
|
|
Yes |
No |
Yes |
No |
No |
No |
No |
|
|
No |
Yes |
No |
No |
No |
Yes |
Yes |
|
|
No |
No |
No |
No |
No |
No |
No |
|
|
No |
No |
No |
Yes3 |
Yes3 |
No |
Yes3 |
|
|
VIC2-4FXO (FXO/CAMA) |
No |
No |
No |
Yes |
Yes |
No |
Yes |
|
VIC2-2FXO (FXO/CAMA) |
No |
No |
No |
Yes |
Yes |
No |
Yes |
|
VIC2-2FXS |
No |
No |
No |
Yes |
Yes |
No |
Yes |
|
VIC2-2E/M |
No |
No |
No |
Yes |
Yes |
No |
Yes |
|
VIC2-2BRI- NT/TE |
No |
No |
No |
Yes |
Yes |
No |
Yes |
|
VWIC-xMFT-E1 (with or without DI) |
No |
Yes |
No |
No |
Yes |
Yes |
Yes |
|
VWIC-1MFT-G703 |
No |
No |
No |
No |
No |
No |
Yes |
|
No |
Yes |
No |
No |
No |
Yes |
Yes |
|
|
VWIC-xMFT-T1 (with or without DI) |
No |
Yes |
No |
No |
Yes |
Yes |
Yes |
Note:
-
1The NM-HD-1V and NM-HD-2V have feature parity with the NM-1V and NM-2V. However, there is currently no support on NM-1V and NM-2V for:
-
Trunked AAL2 on analog ports
-
Universal FXO (VIC2-xFXO) voice cards with software-selectable CAMA
-
Any VIC2 cards, such as VIC2-2BRI-NT/TE, VIC2-2FXS, VIC2-2E/M, and VIC-4FXS/DID cards
-
The drop of DSPs on a POTS-to-POTS call that stays within the network module
-
-
2The NM-HD-2VE interfaces have feature parity with the NM-HDV. However, there is currently no support on the NM-HD-xx for:
-
Modem relay
There is support for the G.168 ECAN in Cisco IOS Software Release 12.3(4)XD, Cisco IOS Software Release 12.3(7)T, and later. There is support for transcoding and conferencing services in Cisco IOS Software Release 12.3(8)T and later.
-
-
3On this platform series and network module type, the VIC-4FXS/DID card currently does not support the DID mode of operation. The voice ports only operate as FXS interfaces. Support for both modes of operation will be available in Cisco IOS Software Release 12.3(14)T. If analog DID is necessary at this time, use the VIC-2DID product instead.
|
Routers/Gateways |
||||||
|---|---|---|---|---|---|---|
|
Model |
||||||
|
Voice Network Module (right) |
Not Used |
NM- HDV2 |
Chassis slot |
|||
|
VIC (below) |
||||||
|
No |
No |
No |
No |
No |
No |
|
|
No |
No |
No |
No |
No |
No |
|
|
No |
No |
No |
No |
No |
No |
|
|
No |
No |
No |
No |
No |
No |
|
|
No |
No |
No |
No |
No |
No |
|
|
No |
No |
No |
No |
No |
No |
|
|
Yes |
Yes |
Yes |
No |
Yes |
Yes |
|
|
No |
No |
No |
No |
No |
No |
|
|
No |
No |
No |
Yes |
Yes |
No |
|
|
No |
No |
No |
No |
No |
No |
|
|
Yes |
Yes3 |
Yes3 |
No |
Yes3 |
Yes3 |
|
|
VIC2-4FXO (FXO/CAMA) |
Yes |
Yes |
Yes |
No |
Yes |
Yes |
|
VIC2-2FXO (FXO/CAMA) |
Yes |
Yes |
Yes |
No |
Yes |
Yes |
|
VIC2-2FXS |
Yes |
Yes |
Yes |
No |
Yes |
Yes |
|
VIC2-2E/M |
Yes |
Yes |
Yes |
No |
Yes |
Yes |
|
VIC2-2BRI- NT/TE |
Yes |
Yes |
Yes |
No |
Yes |
Yes |
|
VWIC-xMFT-E1 (with or without DI) |
Yes |
No |
Yes |
Yes |
Yes |
Yes |
|
VWIC-1MFT-G703 |
Yes |
No |
No |
No |
Yes |
Yes |
|
Yes |
No |
No |
Yes |
Yes |
Yes |
|
|
VWIC-xMFT-T1 (with or without DI) |
Yes |
No |
Yes |
Yes |
Yes |
Yes |
Note:
-
1The NM-HD-1V and NM-HD-2V have feature parity with the NM-1V and NM-2V. However, there is currently no support on NM-1V and NM-2V for:
-
Trunked AAL2 on analog ports
-
Universal FXO (VIC2-xFXO) voice cards with software-selectable CAMA
-
Any VIC2 cards, such as VIC2-2BRI-NT/TE, VIC2-2FXS, VIC2-2E/M, and VIC-4FXS/DID cards
-
The drop of DSPs on a POTS-to-POTS call that stays within the network module
-
-
2The NM-HD-2VE interfaces have feature parity with the NM-HDV. However, there is currently no support on the NM-HD-xx for:
-
Modem relay
There is support for the G.168 ECAN in Cisco IOS Software Release 12.3(4)XD, Cisco IOS Software Release 12.3(7)T, and later. There is support for transcoding and conferencing services in Cisco IOS Software Release 12.3(8)T and later.
-
-
3On this platform series and network module type, the VIC-4FXS/DID card currently does not support the DID mode of operation. The voice ports only operate as FXS interfaces. Support for both modes of operation will be available in Cisco IOS Software Release 12.3(14)T. If analog DID is necessary at this time, use the VIC-2DID product instead.
Cisco ICS 7750, 36xx, 37xx, and 38xx Platforms Matrix
|
Routers/Gateways |
||||||||
|---|---|---|---|---|---|---|---|---|
|
Model |
||||||||
|
Voice Network Module (right) |
||||||||
|
VIC (below) |
||||||||
|
No |
Yes |
No |
Yes |
No |
No |
No |
||
|
Yes |
Yes |
No |
Yes |
No |
No |
No |
||
|
Yes |
Yes |
No |
Yes |
No |
No |
No |
||
|
Yes |
Yes |
No |
Yes |
No |
No |
No |
||
|
No |
Yes |
No |
Yes |
No |
No |
No |
||
|
Yes |
Yes |
No |
Yes |
No |
No |
No |
||
|
Yes |
Yes |
No |
Yes |
Yes |
Yes |
No |
||
|
No |
Yes |
No |
Yes |
No |
No |
No |
||
|
No |
No |
Yes |
No |
No |
No |
Yes |
||
|
Yes |
No |
No |
No |
No |
No |
No |
||
|
Yes |
No |
No |
No |
Yes3 |
Yes3 |
No |
||
|
VIC2-4FXO (FXO/CAMA) |
Yes |
No |
No |
No |
Yes |
Yes |
No |
|
|
VIC2-2FXO (FXO/CAMA) |
No |
No |
No |
No |
Yes |
Yes |
No |
|
|
VIC2-2FXS |
No |
No |
No |
No |
Yes |
Yes |
No |
|
|
VIC2-2E/M |
Yes |
No |
No |
No |
Yes |
Yes |
No |
|
|
VIC2-2BRI- NT/TE |
Yes |
No |
No |
No |
Yes |
Yes |
No |
|
|
VWIC-xMFT-E1 (with or without DI) |
Yes4 |
No |
Yes |
No |
No |
Yes |
Yes |
|
|
VWIC-1MFT-G703 |
No |
No |
No |
No |
No |
No |
No |
|
|
No |
No |
Yes |
No |
No |
No |
Yes |
||
|
VWIC-xMFT-T1 (with or without DI) |
Yes4 |
No |
Yes |
No |
No |
Yes |
Yes |
|
Note:
-
1The NM-HD-1V and NM-HD-2V have feature parity with the NM-1V and NM-2V. However, there is currently no support on NM-1V and NM-2V for:
-
Trunked AAL2 on analog ports
-
Universal FXO (VIC2-xFXO) voice cards with software-selectable CAMA
-
Any VIC2 cards, such as VIC2-2BRI-NT/TE, VIC2-2FXS, VIC2-2E/M, and VIC-4FXS/DID cards
-
The drop of DSPs on a POTS-to-POTS call that stays within the network module
-
-
2The NM-HD-2VE interfaces have feature parity with the NM-HDV. However, there is currently no support on the NM-HD-xx for:
-
Modem relay
There is support for the G.168 ECAN in Cisco IOS Software Release 12.3(4)XD, Cisco IOS Software Release 12.3(7)T, and later. There is support for transcoding and conferencing services in Cisco IOS Software Release 12.3(8)T and later.
-
-
3On this platform series and network module type, the VIC-4FXS/DID card currently does not support the DID mode of operation. The voice ports only operate as FXS interfaces. Support for both modes of operation will be available in Cisco IOS Software Release 12.3(14)T. If analog DID is necessary at this time, use the VIC-2DID product instead.
-
4The ICS 7750 does not support VWIC-2MFT-T1-DI and VWIC-2MFT-E1-DI cards with DI.
|
Routers/Gateways |
||||||
|---|---|---|---|---|---|---|
|
Model |
||||||
|
Voice Network Module (right) |
NM- HDV2 |
|||||
|
VIC (below) |
||||||
|
Yes |
No |
No |
No |
No |
||
|
Yes |
No |
No |
No |
No |
||
|
Yes |
No |
No |
No |
No |
||
|
Yes |
No |
No |
No |
No |
||
|
Yes |
No |
No |
No |
No |
||
|
Yes |
No |
No |
No |
No |
||
|
Yes |
Yes |
Yes |
No |
Yes |
||
|
Yes |
No |
No |
No |
No |
||
|
No |
No |
No |
Yes |
Yes |
||
|
No |
No |
No |
No |
No |
||
|
No |
Yes3 |
Yes3 |
No |
Yes3 |
||
|
VIC2-4FXO (FXO/CAMA) |
No |
Yes |
Yes |
No |
Yes |
|
|
VIC2-2FXO (FXO/CAMA) |
No |
Yes |
Yes |
No |
Yes |
|
|
VIC2-2FXS |
No |
Yes |
Yes |
No |
Yes |
|
|
VIC2-2E/M |
No |
Yes |
Yes |
No |
Yes |
|
|
VIC2-2BRI- NT/TE |
No |
Yes |
Yes |
No |
Yes |
|
|
VWIC-xMFT-E1 (with or without DI) |
No |
No |
Yes |
Yes |
Yes |
|
|
VWIC-1MFT-G703 |
No |
No |
No |
No |
Yes |
|
|
No |
No |
No |
Yes |
Yes |
||
|
VWIC-xMFT-T1 (with or without DI) |
No |
No |
Yes |
Yes |
Yes |
|
Note:
-
1The NM-HD-1V and NM-HD-2V have feature parity with the NM-1V and NM-2V. However, there is currently no support on NM-1V and NM-2V for:
-
Trunked AAL2 on analog ports
-
Universal FXO (VIC2-xFXO) voice cards with software-selectable CAMA
-
Any VIC2 cards, such as VIC2-2BRI-NT/TE, VIC2-2FXS, VIC2-2E/M, and VIC-4FXS/DID cards
-
The drop of DSPs on a POTS-to-POTS call that stays within the network module
-
-
2The NM-HD-2VE interfaces have feature parity with the NM-HDV. However, there is currently no support on the NM-HD-xx for:
-
Modem relay
There is support for the G.168 ECAN in Cisco IOS Software Release 12.3(4)XD, Cisco IOS Software Release 12.3(7)T, and later. There is support for transcoding and conferencing services in Cisco IOS Software Release 12.3(8)T and later.
-
-
3On this platform series and network module type, the VIC-4FXS/DID card currently does not support the DID mode of operation. The voice ports only operate as FXS interfaces. Support for both modes of operation will be available in Cisco IOS Software Release 12.3(14)T. If analog DID is necessary at this time, use the VIC-2DID product instead.
|
Routers/Gateways |
||||||
|---|---|---|---|---|---|---|
|
Model |
||||||
|
Voice Network Module (right) |
NM- HDV2 |
Chassis slot |
||||
|
VIC (below) |
||||||
|
No |
No |
No |
No |
No |
||
|
No |
No |
No |
No |
No |
||
|
No |
No |
No |
No |
No |
||
|
No |
No |
No |
No |
No |
||
|
No |
No |
No |
No |
No |
||
|
No |
No |
No |
No |
No |
||
|
Yes |
Yes |
No |
Yes |
Yes |
||
|
No |
No |
No |
No |
No |
||
|
No |
No |
Yes |
Yes |
No |
||
|
No |
No |
No |
No |
No |
||
|
Yes3 |
Yes3 |
No |
Yes3 |
Yes3 |
||
|
VIC2-4FXO (FXO/CAMA) |
Yes |
Yes |
No |
Yes |
Yes |
|
|
VIC2-2FXO (FXO/CAMA) |
Yes |
Yes |
No |
Yes |
Yes |
|
|
VIC2-2FXS |
Yes |
Yes |
No |
Yes |
Yes |
|
|
VIC2-2E/M |
Yes |
Yes |
No |
Yes |
Yes |
|
|
VIC2-2BRI- NT/TE |
Yes |
Yes |
No |
Yes |
Yes |
|
|
VWIC-xMFT-E1 (with or without DI) |
No |
Yes |
Yes |
Yes |
Yes |
|
|
VWIC-1MFT-G703 |
No |
No |
No |
Yes |
Yes |
|
|
No |
No |
Yes |
Yes |
Yes |
||
|
VWIC-xMFT-T1 (with or without DI) |
No |
Yes |
Yes |
Yes |
Yes |
|
Note:
-
1The NM-HD-1V and NM-HD-2V have feature parity with the NM-1V and NM-2V. However, there is currently no support on NM-1V and NM-2V for:
-
Trunked AAL2 on analog ports
-
Universal FXO (VIC2-xFXO) voice cards with software-selectable CAMA
-
Any VIC2 cards, such as VIC2-2BRI-NT/TE, VIC2-2FXS, VIC2-2E/M, and VIC-4FXS/DID cards
-
The drop of DSPs on a POTS-to-POTS call that stays within the network module
-
-
2The NM-HD-2VE interfaces have feature parity with the NM-HDV. However, there is currently no support on the NM-HD-xx for:
-
Modem relay
There is support for the G.168 ECAN in Cisco IOS Software Release 12.3(4)XD, Cisco IOS Software Release 12.3(7)T, and later. There is support for transcoding and conferencing services in Cisco IOS Software Release 12.3(8)T and later.
-
-
3On this platform series and network module type, the VIC-4FXS/DID card currently does not support the DID mode of operation. The voice ports only operate as FXS interfaces. Support for both modes of operation will be available in Cisco IOS Software Release 12.3(14)T. If analog DID is necessary at this time, use the VIC-2DID product instead.
DSP Module Support Matrix
|
Routers/Gateways |
|||
|---|---|---|---|
|
Model (right) |
VG200 1 |
||
|
DSP Module (below) |
|||
|
AIM-VOICE-30 |
— |
— |
No |
|
AIM-ATM-VOICE-30 |
— |
— |
No |
|
NM-HDV-FARM |
— |
— |
Yes |
|
PVDM-12 |
No |
No |
Yes |
|
DSP-HDA-16 |
No |
No |
No |
|
PVDM-41 |
Yes |
No |
No |
|
PVDM-81 |
Yes |
No |
No |
|
PVDM-256K-4 |
No |
Yes |
No |
|
PVDM-256K-8 |
No |
Yes |
No |
|
PVDM-256K-16 |
No |
Yes |
No |
|
PVDM-256K-20 |
No |
Yes |
No |
|
PVDM-256K-16HD |
No |
Yes |
No |
|
PVDM-256K-20HD |
No |
Yes |
No |
|
PVDM2-8 |
No |
No |
No |
|
PVDM2-16 |
No |
No |
No |
|
PVDM2-32 |
No |
No |
No |
|
PVDM2-48 |
No |
No |
No |
|
PVDM2-64 |
No |
No |
No |
Note:
-
1These products have reached end of sale. Refer to the End-of-Sale Announcement for the Cisco VG200 Access Gateway.
|
Routers/Gateways |
|||||
|---|---|---|---|---|---|
|
Model (right) |
|||||
|
DSP Module (below) |
|||||
|
AIM-VOICE-30 |
Yes |
Yes |
No |
No |
— |
|
AIM-ATM-VOICE-30 |
Yes |
Yes |
No |
No |
— |
|
NM-HDV-FARM |
Yes2 |
Yes |
No |
Yes |
— |
|
PVDM-12 |
Yes |
Yes |
No |
Yes3 |
No |
|
DSP-HDA-16 |
Yes |
Yes |
No |
Yes4 |
No |
|
PVDM-41 |
No |
No |
No |
No |
Yes |
|
PVDM-81 |
No |
No |
No |
No |
Yes |
|
PVDM-256K-4 |
No |
No |
No |
No |
Yes |
|
PVDM-256K-8 |
No |
No |
No |
No |
Yes |
|
PVDM-256K-16 |
No |
No |
No |
No |
Yes |
|
PVDM-256K-20 |
No |
No |
No |
No |
Yes |
|
PVDM-256K-16HD |
No |
No |
No |
No |
No |
|
PVDM-256K-20HD |
No |
No |
No |
No |
No |
|
PVDM2-8 |
No |
Yes |
Yes |
Yes |
No |
|
PVDM2-16 |
No |
Yes |
Yes |
Yes |
No |
|
PVDM2-32 |
No |
Yes |
Yes |
Yes |
No |
|
PVDM2-48 |
No |
Yes |
Yes |
Yes |
No |
|
PVDM2-64 |
No |
Yes |
Yes |
Yes |
No |
Note:
-
1These products have reached end of sale. Refer to the End-of-Sale Announcement for the Cisco VG200 Access Gateway.
-
2There is support on the 2650 and 2651, but not on the 261x and 262x.
-
3The PVDM-12 only has support on the Cisco 2811, 2821, 2851, 3825, and 3845 when the PVDM-12 is installed on a NM-HDV-FARM or NM-HDV network module. The voice router itself only supports the PVDM2 series of DSP cards.
-
4The DSP-HDA-16 only has support on the Cisco 2811, 2821, 2851, 3825, and 3845 when DSP-HDA-16 is installed on a NM-HDA-4FXS network module. The voice router itself only supports the PVDM2 series of DSP cards.
|
Routers/Gateways |
|||||
|---|---|---|---|---|---|
|
Model (right) |
|||||
|
DSP Module (below) |
|||||
|
AIM-VOICE-30 |
No |
No |
Yes2 |
Yes |
No |
|
AIM-ATM-VOICE-30 |
No |
No |
Yes2 |
Yes |
No |
|
NM-HDV-FARM |
No |
Yes |
Yes |
Yes |
Yes |
|
PVDM-12 |
Yes |
Yes |
Yes |
Yes |
Yes3 |
|
DSP-HDA-16 |
No |
Yes |
Yes |
Yes |
Yes4 |
|
PVDM-41 |
No |
No |
No |
No |
No |
|
PVDM-81 |
No |
No |
No |
No |
No |
|
PVDM-256K-4 |
No |
No |
No |
No |
No |
|
PVDM-256K-8 |
No |
No |
No |
No |
No |
|
PVDM-256K-16 |
No |
No |
No |
No |
No |
|
PVDM-256K-20 |
No |
No |
No |
No |
No |
|
PVDM-256K-16HD |
No |
No |
No |
No |
No |
|
PVDM-256K-20HD |
No |
No |
No |
No |
No |
|
PVDM2-8 |
No |
No |
No |
Yes |
Yes |
|
PVDM2-16 |
No |
No |
No |
Yes |
Yes |
|
PVDM2-32 |
No |
No |
No |
Yes |
Yes |
|
PVDM2-48 |
No |
No |
No |
Yes |
Yes |
|
PVDM2-64 |
No |
No |
No |
Yes |
Yes |
Note:
-
1These products have reached end of sale. Refer to the End-of-Sale Announcement for the Cisco VG200 Access Gateway.
-
2On the Cisco 3660, the AIM-VOICE-30 and AIM-ATM-VOICE-30 products only have support when there is also a multiservice interchange (MIX) daughter card installed.
-
3The PVDM-12 only has support on the Cisco 2811, 2821, 2851, 3825, and 3845 when the PVDM-12 is installed on a NM-HDV-FARM or NM-HDV network module. The voice router itself only supports the PVDM2 series of DSP cards.
-
4The DSP-HDA-16 only has support on the Cisco 2811, 2821, 2851, 3825, and 3845 when DSP-HDA-16 is installed on a NM-HDA-4FXS network module. The voice router itself only supports the PVDM2 series of DSP cards.
Catalyst Support Matrix
This table shows the relationship between Catalyst switches, voice blades, and VICs:
Note: The VICs that are not listed in this matrix do not receive support from the Catalyst switches.
|
Product Name |
Catalyst Switches |
|
|---|---|---|
|
WS-X6608-T1/E1 Provides a high-end T1 gateway to the Public Switched Telephone Network (PSTN) or legacy Private Branch Exchanges (PBXs) and network-based voice services |
No |
CatOS 5.5(1) |
|
WS-X6624-FXS Connects legacy analog telephony equipment such as phones, speaker phones, and faxes |
No |
CatOS 5.5(3) |
|
WS-X6348-RJ45V Inline power 10/100BASE-T Ethernet switching modules. Equivalent to a WS-X6348-RJ45 10/100BASE-T Ethernet switching module with inline power daughter module WS-F6K-VPWR= |
No |
CatOS 5.5(1) |
|
WS-SVC-CMM Provides up to 18 T1/E1 gateways to the PSTN or legacy PBXs and network-based voice services |
No |
CatOS 7.3(1) |
|
WS-X4148-RJ45V Inline power 10/100BASE-T Ethernet switching modules |
CatOS 6.1(1) |
No |
|
VIC-2FXS Two-port FXS VIC |
Cisco IOS Software Release 12.1(3a)XI |
No |
|
VIC-2FXO Two-port FXO VIC |
Cisco IOS Software Release 12.1(3a)XI |
No |
|
VIC-2FXO-EU Two-port FXO for Europe |
Cisco IOS Software Release 12.1(3a)XI |
No |
|
VIC-2BRI-S/T-TE Two-port ISDN BRI VIC, S/T interface, terminal equipment |
Yes |
No |
|
VWIC-1MFT-T1 One-port RJ-48 multiflex trunk T1 |
Cisco IOS Software Release 12.1(3a)XI |
No |
|
VWIC-2MFT-T1 Two-port RJ-48 multiflex trunk T1 |
Cisco IOS Software Release 12.1(3a)XI |
No |
|
VWIC-2MFT-T1-DI Two-port RJ-48 multiflex trunk E1 with DI |
Cisco IOS Software Release 12.1(3a)XI |
No |
|
VWIC-1MFT-E1 One-port RJ-48 multiflex trunk E1 |
Cisco IOS Software Release 12.1(3a)XI |
No |
|
VWIC-2MFT-E1 Two-port RJ-48 multiflex trunk E1 |
Cisco IOS Software Release 12.1(3a)XI |
No |
|
VWIC-2MFT-E1-DI Two-port RJ-48 multiflex trunk E1 with DI |
Cisco IOS Software Release 12.1(3a)XI |
No |
Note: The Cisco IOS Software releases provided are typically the minimum version necessary to support the platform, module, or feature in question. For a complete list of Cisco IOS Software releases that support a feature, module, interface card, or chassis, use the Software Advisor ( registered customers only) tool.
NetPro Discussion Forums - Featured Conversations
| NetPro Discussion Forums - Featured Conversations for Voice |
| Service Providers: Voice over IP |
| Voice & Video: Voice over IP |
| Voice & Video: IP Telephony |
| Voice & Video: IP Phone Services for End Users |
| Voice & Video: Unified Communications |
| Voice & Video: IP Phone Services for Developers |
| Voice & Video: General |
Related Information
- White Paper: Cisco IOS Reference Guide
- Product Bulletin - No. 537, Types of Cisco IOS Software Releases
- Voice Features for Cisco 3600 Series Routers
- Voice Network Module and Voice Interface Card Configuration Note
- Voice/Fax NMs
- Voice Technology Support
- Voice and IP Communications Product Support
-
Recommended Reading:
Troubleshooting Cisco IP Telephony
- Technical Support & Documentation - Cisco Systems
| Updated: Jul 31, 2008 | Document ID: 5111 |