The equipment failure Invalid MAC Address (INVMACADR) is a Major (MJ), Non-Service Affecting (NSA) alarm that occurs when the MAC address of a Cisco ONS 15454 is invalid. This document explains the causes of this problem and provides the appropriate solution.
There are no specific requirements for this document.
The information in this document is based on the Cisco ONS 15454.
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Refer to Cisco Technical Tips Conventions for more information on document conventions.
A MAC address is a 48-bit, Layer 2 (L2) address that is permanently assigned to all devices on a network. MAC address is the physical or hardware address (as opposed to the network address) of the device. Every Cisco ONS 15454 has a unique, factory-assigned MAC address that resides in the Alarm Interface Panel (AIP) card. The Timing Communications and Control (TCC), TCC+, and TCC2 cards (both active and standby) read the MAC address value from the AIP memory chip at boot-up, and keep this value in Synchronous Dynamic RAM (SDRAM). You can view the read-only MAC address in the Provisioning/Network tab in the Cisco Transport Controller (CTC).
The Cisco ONS 15454 uses both IP and MAC addresses for circuit routing. When an Invalid MAC Address alarm exists on a node, an incomplete circuit appears in CTC in the circuit status column. The circuit still works and carries traffic without any problem, but the CTC cannot logically display the end-to-end information for that circuit.
Here are the possible causes of an invalid MAC address:
The TCC cards read the chassis MAC address value from the AIP card at boot-up. If there is a read error, the default MAC address (00-10-cf-ff-ff-ff) is used.
The two TCC cards in the Cisco ONS 15454 read the MAC address independently, so a read error can cause each card to read a different value for the address.
The AIP card holds the chassis MAC address, so component failures in the AIP card can cause a read error.
Complete these steps in order to resolve this problem:
Resolve any outstanding alarms raised against the active or standby TCC+/TCC2.
Visually inspect the LCD display on the fan tray.
If the LCD is blank or the text is garbled, proceed to step 7.
At the earliest maintenance window, perform a software reset on the standby TCC+/TCC2.
Right-click the standby TCC+ when logged into CTC, and select Reset Card. You receive a prompt to indicate whether you are sure. Choose Yes. As the card resets, a loading (Ldg) indication appears on the card in CTC.
Note: The reset takes approximately five minutes. Do not perform any other steps until the reset is complete.
If this card fails to boot up in Stby and continuously reloads, the AIP is probably defective. The Stby TCC+/TCC2 attempts to read the erasable programmable read-only memory (EEPROM) on the AIP, and continues to reload until it is successful. Proceed to step 7.
Sideswitch the TCC+/TCC2s. To do so, follow the procedure in the Reset Active TCC+/TCC2 Card and Activate Standby Card section in chapter 2 of the Cisco ONS 15454 Troubleshooting Guide, Releases 4.1.x and 4.5.
Check whether the INVMACADR alarm is still present.
When you reset the active TCC+/TCC2, the standby TCC+/TCC2 becomes active. The standby TCC+/TCC2 keeps a copy of the chassis MAC address. If the stored MAC address is valid, the alarm must clear.
Sideswitch the TCC+/TCC2s once again to make the original TCC active. To do so, follow the procedure in the Reset Active TCC+/TCC2 Card and Activate Standby Card section in chapter 2 of the Cisco ONS 15454 Troubleshooting Guide, Releases 4.1.x and 4.5.
Check whether the INVMACADR alarm is still present.
If the INVMACADR was present for both step 4 and step 5, the AIP is probably defective. Proceed to step 7.
If the INVMACADR was present only in either step 4 or step 5, replace the TCC+/TCC2 that was active at that time. If the card is currently in standby, you can simply remove and replace the card. If the card is active, follow the procedure in Reset Active TCC+/TCC2 Card and Activate Standby Card in order to make the card standby, and then simply remove and replace the card.
Note: If the replacement TCC+/TCC2 is loaded with a software version other than that of the active TCC+/TCC2, the card can take up to 30 minutes to load. The LEDs flicker between Fail and Act/Stby while the software is copied from the active TCC+/TCC2.
Open a case with the Cisco Technical Assistance Center for assistance on how to determine the previous MAC address of the node. Replace the AIP. To do so, follow the procedure in the Replace the Alarm Interface Panel section in chapter 3 of the Cisco ONS 15454 Troubleshooting Guide, Releases 4.1.x and 4.5.
The Cisco Support Community is a forum for you to ask and answer questions, share suggestions, and collaborate with your peers.
Refer to Cisco Technical Tips Conventions for information on conventions used in this document.