Table Of Contents
dbgcon
Debug Connection—PXM45, PXM1E
The node-level dbgcon command enables or disables the SPVC (or SPVP) error log. You can enable the error log for a specific connection by specifying a port ID, VPI, and VCI. To see whether the connection error log is enabled, use the dspcons-dbg command.
This command can substantially increase CPU usage, so you should seriously consider whether its usage is safe in your circumstances. This potential is greater when all connections are included.
Syntax
dbgcon <enable | disable> [-port <portid> -vpi <vpi> -vci <vci>]
Syntax Description
enable | disable
Enter enable or disable to start or stop the SPVC log.
Default: disabled.
-port
Enter -port followed by the value of the portid for the specific SPVC. The format of the PNNI physical port identifier can vary, as follows:
•
On a PXM45: slot:subslot.port:subport
•
–
–
•
For more details, see the section, "PNNI Format," in "Introduction."
-vpi
Enter -vpi followed by the value of the vpi for the specific SPVC.
The range is 0-4095.-vci
Enter -vci followed by the value of the vpi for the specific SPVC.
The range is 1-65535.
Related Commands
dspcons-dbg
Attributes
Example
Enable the SPVC log for the connection with port ID 9:1.8:8 and VPI/VCI100/100.
MGX8850.8.PXM.a > dbgcon enable -port 9:1.8:8 -vpi 100 -vci 100dbgilmi
Debug ILMI—PXM45, PXM1E
Use dbgilmi to debug ILMI functionality (such as address registration or auto configuration).
Note
Syntax
dbgilmi {enable | disable} [<portid>] [-log <vsi | func | minor | major | warning | error | dump | fatal | all>] [-dbg <vsi | func | minor | major | warning | error | dump | fatal | all>]
Syntax Description
enable | disable
Activate or de-activate ILMI debugging.
portid
The format of the PNNI physical port identifier can vary, as follows:
•
•
–
–
•
For more details, see the section, "PNNI Format," in "Introduction."
-log
If you type the optional keyword log, follow it with at least one of the following:
vsi
func
minor
major
warning
error
dump
fatal
all: log all-dbg
If you type the optional keyword dbg, follow it with at least one of the following:
vsi
func
minor
major
warning
error
dump
fatal
all: dbg all
Attributes
dbgpnni
Debug PNNI Messages—PXM45, PXM1E
The dbgpnni command lets you specify the types of debug messages that appear in the display of the dsppnni-dbg command.
Note
Syntax
dbgpnni [-all {on | off}] [-hello {on | off}] [-election {on | off}] [-nbr {on | off}] [-itf {on | off}] [-timer {on | off}] [-lgn {on | off}] [-spt {on | off}] [-nodereachability {on | off}] [-address {on | off}] [-itdb {on | off}] [-ra {on | off}] [-cp {on | off}] [-linkselection {on | off}]
Syntax Description
Related Commands
dsppnni-dbg
Attributes
Example
Specify the following PNNI debug message-options:
•
•
Use dsppnni-dbg to check which debug messages types appear on the terminal.
SanJose.7.PXM.a > dsppnni-dbgpnni debugging option:hello election nbr itf timer lgn spt node reachability----- -------- --- --- ----- --- --- -----------------off off off off off off off offaddress itdb ra cp link selection------- ---- --- --- --------------off off off off offSanJose.7.PXM.a > dbgpnni -itf on -address onSanJose.7.PXM.a > dsppnni-dbgpnni debugging option:hello election nbr itf timer lgn spt node reachability----- -------- --- --- ----- --- --- -----------------off off off on off off off offaddress itdb ra cp link selection------- ---- --- --- --------------on off off off offIn the second example, the parameters are changed as follows:
•
•
SanJose.7.PXM.a > dbgpnni -itf off -address offSanJose.7.PXM.a > dsppnni-dbgpnni debugging option:hello election nbr itf timer lgn spt node reachability----- -------- --- --- ----- --- --- -----------------off off off off off off off offaddress itdb ra cp link selection------- ---- --- --- --------------off off off off offdbgsntp
Debug Simple Network Time Protocol—PXM45, PXM1E
The dbgsntp command lets you enable SNTP debugging and specify the level of debugging. Use the dspsntp-dbg command to see the debugging configuration created with the dbgsntp command.
Syntax
dbgsntp <enable | disable> [ipaddr] [-level <info | trace | debug>]
Syntax Description
Related Commands
cnfsntp, cnfsntprmtsvr, dspsntp, dspsntprmtsvr, addsntprmtsvr, delsntprmtsvr, dspsntpstats
Attributes
Example
dclk
Display Clock Measured by System Clock Test—PXM45, PXM1E
Display the Digital to Analog Converter (DAC) value and the deviation, in parts-per-million, of the output frequency of the current clock source. This is the nominal frequency value for the local oscillator on the PXM45 UIS3 card.
The local oscillator of the UIS3 is an Over-Controlled Crystal Oscillator (OCXO) with a nominal frequency of 19.44Mhz. The control voltage applied to the OCXO by the hardware circuitry on the board adjusts the output frequency range of the clock between +/- 7 PPM (136Hz) to +/- 14PPM (272Hz).
The DAC value is used to convert the digital voltage value, from the DSP FPGA, to the analog voltage, which controls the OCXO. The range of the input DAC value is from 0x0000 to 0xffff with a nominal value of 0x8000.
The dclk output displays the DAC value field, which is the difference between the current measured DAC value and the nominal DAC value of 0x8000, and the PPM values for the last 100 current clock samples that have been taken at the rate of one every second.
Syntax
dclk
Syntax Description
This command takes no parameters.
Related Commands
None
Attributes
Example
M8850_NY.7.PXM.a > dclkSample DAC Dev ppm.1 -900 -0.192 -915 -0.193 -915 -0.194 -915 -0.195 -900 -0.196 -900 -0.197 -916 -0.198 -916 -0.199 -916 -0.1910 -916 -0.1911 -916 -0.1912 -916 -0.1913 -900 -0.1914 -900 -0.1915 -899 -0.1916 -899 -0.1917 -899 -0.1918 -900 -0.1919 -900 -0.1920 -900 -0.1921 -899 -0.1922 -899 -0.1923 -900 -0.1924 -916 -0.1925 -899 -0.1926 -915 -0.1927 -915 -0.1928 -916 -0.1929 -900 -0.1930 -916 -0.1931 -916 -0.1932 -915 -0.1933 -915 -0.1934 -916 -0.1935 -916 -0.1936 -916 -0.1937 -900 -0.1938 -899 -0.1939 -900 -0.1940 -900 -0.1941 -900 -0.1942 -900 -0.1943 -915 -0.1944 -915 -0.1945 -916 -0.1946 -916 -0.1947 -915 -0.1948 -916 -0.19deladdr
Delete Address—PXM45, PXM1E
Removes an ATM address for a UNI or IISP.
Syntax
deladdr <portid> <atm-address> <length> [-plan {e164 | nsap}]
Syntax Description
portid
The format of the PNNI physical port identifier can vary, as follows:
•
•
–
–
•
For more details, see the section, "PNNI Format," in "Introduction."
atm-address
The ATM address: its format depends on whether the address type is NSAP or E.164. The address plan specifies the address type and so determines the maximum number of bytes or bits in the address. You can specify the address plan with the forthcoming -plan option. The default plan is NSAP.
•
•
The number of bits or bytes in the ATM address effects the uniqueness of the address. The longest address ensures total uniqueness of the address. With a one-byte address, any caller that sends an address whose first address byte matches that one-byte ATM address goes to that port.
length
Address length. The units of measure differ for each address plan. The -plan option lets you specify E.164 or NSAP.
•
•
-plan
Address plan: E.164 or NSAP.
Default: nsap
Related Commands
addaddr, dspaddr, deladdrs
Attributes
Example
On port 11:2.8:22, delete 47.0091.8100.0000.0000.0ca7.9e01.4000.0c81.8000.00. Note that the command entry includes the address length of 160 after the address.
Geneva.7.PXM.a > deladdr 11:2.8:28 47.0091.8100.0000.0000.0ca7.9e01.4000.0c81.8000.00 160deladdrs
Delete Addresses—PXM45, PXM1E
Removes all ATM addresses on a UNI, AINI, or IISP. The optional plan parameter lets you differentiate by address plan:
•
•
•
Syntax
deladdrs <portid> [-plan {e164 | nsap | all}]
Syntax Description
portid
The format of the PNNI physical port identifier can vary, as follows:
•
•
–
–
•
For more details, see the section, "PNNI Format," in "Introduction."
-plan
Address plan: E.164, NSAP, or all.
Default: all
Related Commands
addaddr, dspaddr, deladdr
Attributes
Example
On port 11:2.8:22, delete all the addresses (regardless of address plan).
Geneva.7.PXM.a > deladdrs 11:2.8:28delallusers
Delete All Users—PXM45, PXM1E
Use the delallusers command to delete every user account except the default user.
Syntax
delallusers
Syntax Description
This command takes no parameters, but the system prompts for confirmation (see Example).
Related Commands
adduser, dspusers, deluser, users
Attributes
Example
Before you use the delallusers command, check the existing user accounts by using the dspusers command to be sure that deleting all users except the defaults is appropriate. Check the list of users after you run the delallusers command.
Delete all users except the default user.
Unknown.7.PXM.a > dspusersUserId AccessLevel-------------------------cisco CISCO_GPservice SERVICE_GPsuperuser SUPER_GPdavid GROUP1Unknown.7.PXM.a > delallusersThis command deletes all users except the default usersdelallusers:Do you want to proceed (Yes/No)? yUnknown.7.PXM.a > dspusersUserId AccessLevel-------------------------cisco CISCO_GPservice SERVICE_GPsuperuser SUPER_GPdelapsln
Delete APS Line—PXM1E
Removes the specified APS line from the switch.
See the description for the addapsln command for a detailed explanation of Automatic Protection Switching (APS).
Syntax
delapsln <workingline>
Syntax Description
Related Commands
addapsln, cnfapsln, dspapsln, switchapsln, dspapsbkplane, clrbecnt, dspbecnt
Attributes
Example
delapsln 1.1.1delbert
Delete Bit Error Rate Test—PXM1E
The delbert command lets you terminate a BERT session. This command applies to service modules that do not have native BERT capability and so require a Service Resource Module (SRM-3T3/C or SRME). An alternative to this command is the cnfbert command but with the enable parameter set to "destroy BERT." See cnfbert syntax description.
Note
Syntax
delbert <LSMSlot.Line.Port>
Syntax Description
Related Commands
cnfbert, dspbert, dspbertcap
Attributes
delclksrc
Delete Clock Source—PXM45, PXM1E
Deletes a user-specified primary or secondary clock source. This command applies on switches that have a manual clock configuration. (See also cnfclksrc and cnfncdp descriptions.) Changing a clock source or changing the priority of the source (primary or secondary) are the most frequent uses of delclksrc. See the description of cnfclksrc for these common uses of delclksrc.
Note
Syntax
delclksrc <priority>
Related Commands
cnfclksrc, dspclksrcs, dspclkalms
Attributes
Example
Delete the primary clock source.
pinnacle.7.PXM.a> delclksrc primarydelcon
Delete Connection—PXM1E
Use the delcon command to delete an SPVC or SPVP. For dual-ended connections, delete the connection at both ends—first at the master end, then at the slave. To delete a single-ended connection, use this command at the master end only.
Syntax
delcon <ifnum> <vpi> <vci>
Syntax Description
Related Commands
dspcon, addcon, cnfcon
Attributes
Example
MGX8850.7.pxm1e.a > delcon 1 10 40Deletion successfuldelcons
Delete Connections—PXM1E
Delete a range of connections.
Caution
Syntax
delcons <ifNum> <vpi> <vci> [-num <num. conns to del>] [-verbose < 1 | 0 >]
Syntax Description
Related Commands
None
Attributes
delconsegep
Delete Connection Segment Endpoint—PXM45, PXM1E
Deletes a segment endpoint on a connection. When both VPI and VCI are present, the segment endpoint is an F5 flow endpoint (for VCCs). When the optional VCI is not present, the segment endpoint is an F4 flow endpoint (for VPCs).
Note
Syntax
delconsegep <portid> <vpi> [vci]
Syntax Description
portid
The format of the PNNI physical port identifier can vary, as follows:
•
•
–
–
•
For more details, see the section, "PNNI Format," in "Introduction."
vpi
VPI of the connection.
vci
VCI of the connection.
Related Commands
cnfoamsegep, dspoamsegep, cnfconsegep, dspconsegep
Attributes
delcontroller
Delete Controller—PXM45, PXM1E
Delete a controller. The delcontroller command does not erase the controller software but directs the switch not to use it.
Syntax
delcontroller <cntrlrId>
Syntax Description
cntrlrId
The controller ID (cntrlrId) has a range of 1-20 and is assigned using addcontroller. To see all controllers on the switch, use dspcontrollers.
Related Commands
addcontroller, dspcontrollers
Attributes
Example
Delete controller 3. In this example, the 3 is the reserved controller ID for LSC.
MGX8850.8.PXM.a > delcontroller 3delfltset
Delete Filter Set—PXM45, PXM1E
Removes an ATM address filter set.
Syntax
delfltset <name> [index]
Syntax Description
Related Commands
addfltset, cnffltset, dspfltset
Attributes
Example
Remove the "connect" filter set from the port.
Geneva.7.PXM.a > delfltset connectdelimagrp
Delete IMA Group—PXM1E
This command deletes an IMA group.
Syntax
delimagrp <group>
Syntax Description
group
The group identifier consists of a bay number as well as a group number in the format bay.group, as follows:
•
•
Related Commands
addimagrp, dspimagrp, dspimagrps, cnfimagrp, rstimagrp
Attributes
Example
Delete IMA group 6.
MGX8850.7.PXM1E.a > delimagrp 2.6delimalnk
Delete IMA Link—PXM1E
This command deletes a link from an IMA group.
Syntax
delimalnk <link>
Syntax Description
Related Commands
dspimagrp, cnfimagrp, rstimagrp, dspimalnk, addimalnk
Attributes
Example
Delete link 16.
MGX8850.7.PXM1E.a > delimalnk 2.16dellink
Delete Link—PXM45, PXM1E
The dellink command lets you remove a link. A link is part of the bulk distribution feature on the SRM-3T3 and SRM-E. See the addlink description for information on bulk mode distribution.
Syntax
dellink <SrmStartLinkIf>
Syntax Description
Related Commands
addlink, cnflink, dsplink
Attributes
dellnloop
Delete Line Loop—PXM1E
Remove the line loopback state from a line.
Syntax
dellnloop < -ds3 | -e3 | -sonet | -ds1 | -e1 > <bay.line>
Syntax Description
-ds3
-e3
-sonet
-ds1
-e1Specifies a DS3, E3, T3, SONET (OC-3c), DS1, or E1 line.
bay.line
The bay is always 2. The line number can be 1 to the highest line on the back card.
Related Commands
addlnloop
Attributes
Example
Deleting a DS3 loopback line.
MGX8850.1.7.PXM1E.a > dellnloop -ds3 2.6 -lpb 3Line loop-back status will be changed.Do you want to proceed (Yes/No) ?dellpback
Delete Loopback—PXM1E
The addlpback command lets you delete a specific loopback that is running on a service module.
Note
Syntax
dellpback <LSMSlot.Line.Port> <loopbackType> <loopbackCode>
Syntax Description
Related Commands
addlpback, dspbertcap
Attributes
delncdpclksrc
Delete NCDP Clock Source—PXM45, PXM1E
The delncdpclksrc command lets you delete an NCDP clock source. See the cnfncdp description for details on the Network Clock Distribution Protocol (NCDP).
Syntax
delncdpclksrc <portID> [clocktype <e1 | t1>]
Syntax Description
portid
The format of the PNNI physical port identifier can vary, as follows:
•
•
–
–
•
For BITS clocks only, portid can be 7.35 or 7.36 in an MGX 8850. In an MGX 8830 chassis, the portid for BITS is either 1.35 or 1.36.
For more details, see the section, "PNNI Format," in "Introduction."
clocktype
Enter e1 or t1 as needed when the port ID is one of the following:
•
•
If the clock type is the default E1, this parameter is not necessary for port IDs 7.35 or 7.36 (or 1.35.or 1.36).
Default: e1
Related Commands
cnfncdp, cnfncdpclksrc, cnfncdpport, dspncdp, dspncdpclksrc, dspncdpclksrcs, dspncdpport, dspncdpports
Attributes
delpart
Delete Resource Partition—PXM1E
Note
Syntax
delpart <if_num> <part_id>
Syntax Description
Related Commands
addpart, cnfpart, dsppart
Attributes
Example
MGX8850.7.PXM1E.a > delpart 1 1delpnni-node
Delete PNNI Node—PXM45, PXM1E
The delpnni-node command removes a PNNI node from the PNNI network topology. A node that this command deletes can be restored with the related command addpnni-node. Confirm the deletion of nodes with the dsppnni-node command.
Syntax
delpnni-node <node-index>
Syntax Description
node-index
The node index indicates the relative level of the logical node within a multi-peer group on the switch. The range is 1-10, and the lowest level is 1.
Range: 1-10
Default: 1
Related Commands
addpnni-node, cnfpnni-node, delpnni-node
Attributes
Example
Delete the node with the node-index of 3. Execute dsppnni-node and specify a node index of 3. The last line of the d display shows the error "node does not exist," indicating you successfully deleted the node.
SanJose.7.PXM.a > delpnni-node 3SanJose.7.PXM.a > dsppnni-node 3Unknown Error CodeSyntax: dsppnni-node [node-index]nodeIndex -- node-index: 32 bit number starting from 1, Optional parameterpossible errors are:node does not existSanJose.7.PXM.a >delpnni-summary-addr
Delete PNNI Summary Address—PXM45, PXM1E
The delpnni-summary-addr command deletes a PNNI summary address for a PNNI node.
Syntax
delpnni-summary-addr <node-index> <address-prefix> <prefix-length>
Syntax Description
Related Commands
addpnni-summary-addr, dsppnni-summary-addr
Attributes
Example
Delete a summary address, as follows:
•
•
•
If necessary, use dsppnni-summary-addr to confirm the deletion.
SanJose.7.PXM.a > delpnni-summary-addr 1 47.0091.8100.0000.0030.9409.f1f1 104SanJose.7.PXM.a >delpnport
Delete PNNI Port—PXM45, PXM1E
The delpnport command lets you remove a UNI or NNI port from the controller. It is allowed only if the PNNI port does not exist on the switch i.e, the PNNI partition associated with the port is removed. If the controller does no provisioning on the port in the Plug and Play Scenario, then the PNNI port on the controller is removed if you remove the PNNI Partition on the switch.
Syntax
delpnport <portid>
Syntax Description
portid
The format of the PNNI physical port identifier can vary, as follows:
•
•
–
–
•
For more details, see the section, "PNNI Format," in "Introduction."
Related Commands
addpnport, uppnport, dnpnport, dsppnport
Attributes
Example
Delete port 11:2.8:28 from the switch.
Geneva.7.PXM.a > delpnport 11:2.8:28delpnportacc
Delete Port Access—PXM45, PXM1E
Removes an address access filter group from a port.
Syntax
delpnportacc <portid> {in | out}
Syntax Description
portid
The format of the PNNI physical port identifier can vary, as follows:
•
•
–
–
•
For more details, see the section, "PNNI Format," in "Introduction."
in
Delete incoming access group for the port.
out
Delete outgoing access group for the port.
Related Commands
cnfpnportacc
Attributes
Example
Delete the filter group for incoming calls from port 11:2.8:28.
Geneva.7.PXM.a > delpnportacc 11:2.8:28 indelport
Delete Port—PXM1E
Remove a logical port from a service module. You must delete all connections and resource partitions on the port before you can delete it.
Syntax
delport <ifNum>
Syntax Description
Related Commands
addport, cnfport, dspport, dspports
Attributes
delpref
Delete Preferred Route—PXM45, PXM1E
The delpref command lets you delete a preferred route description. For you to do so, no SPVCs can have the preffered route currently associated with them. For detailed information about preferred routes, see the addpref description.
Syntax
delpref <route-id>
Syntax Description
Related Commands
addpref, dsppref, dspprefs, modpref
Attributes
Example
delprfx
Delete Prefix—PXM45, PXM1E
The delprfx command lets you delete an ILMI address prefix associated with a UNI, IISP, or AINI.
Syntax
delprfx <portid> <atm-prefix>
Syntax Description
portid
The format of the PNNI physical port identifier can vary, as follows:
•
•
–
–
•
For more details, see the section, "PNNI Format," in "Introduction."
atm-prefix
A 13-byte ATM address prefix, specified as 26 hexadecimal characters.
Related Commands
addprfx, dspprfx
Attributes
Examples
Delete ATM prefix 47.0091.8100.0000.0000.0ca7.9e01 from PNNI physical port 3:1.1:1. Display prefixes for this port.
M8850_NY.7.PXM.a > delprfx 3:1.1:1 47.0091.8100.0000.0000.0ca7.9e01M8850_NY.7.PXM.a > dspprfx 3:1.1:1INFO: No Prefix registeredM8850_NY.7.PXM.a >delred
Delete Redundancy—PXM1E
The delred command lets you delete the redundancy between a pair of card slots. It applies to 1:1 and 1:N redundancy.
Note
In the current release, only the PXM1E supports SRMs.The higher speed cards support only 1:1 redundancy. The T1 and E1 service modules can have 1:N redundancy provided by an SRM. When you delete redundancy, the switch resets the primary card.
Syntax
delred <redPrimarySlotNumber>
Syntax Description
Related Commands
addred, dspred, switchredcd
delrscprtn
Delete Resource Partition—PXM1E
Delete a resource partition. Note that you must delete all connections in the resource partition before you delete it. For information on resource partitions, refer to the description of addrscprtn.
Syntax
delrscprtn <if_num> <part_id>
Syntax Description
if_num
The range for logical interface (port) numbers is 1-31.
part_id
The partition ID number in the range 1-20. Use dsprscprtns to see all resource partitions if necessary.
Related Commands
addrscprtn, dsprscprtns, delpart, addpart, dsppart
Attributes
Example
MGX8850.7.PXM1E.a > delrscprtn 1 1delsct
Delete Service Class Temple—PXM45, PXM1E
The delsct command completely removes a service class template (SCT) from the switch. For an SCT that already operates at the port or card level, this command has no immediate effect. The purpose of this command is to remove excess or unused SCTs.
Before the operation proceeds to completion, the system prompts you with a warning, as follows:
Note
Syntax
delsct <cardtype> <scttype> <sctid> <majorversion>
Syntax Description
Related Commands
addsct, cnfsct, dspscts, setsctver, addport, cnfport, dspport, cnfcdsct, dspportsct, dspcdsct, dspsct
Attributes
Example
Delete port-level SCT 1 for AXSM card types. When prompted with a warning, abort the operation.
D1.7.PXM.a > delsct 1 1 1 1Warning: this SCT may be in use on the service modules or the PXM1E. Please verify SCT usage on these cards by using the dspports command. After a reset, cards may revert to default SCT if the provisioned SCT is not found.Do you want to proceed (Yes/No)? n(command not executed)delsesn
Delete Session—PXM45, PXM1E
The delsesn command lets you terminate one or more user-sessions. To see the number of the each active session, use the dspsesn command. Termination takes place immediately upon command execution. Before it proceeds, the CLI warns you that the command is destructive. If you proceed with the deletion, the user whose session is being deleted receives the message, "Forced Logout By <userid> !!!!!!!!!!!," where userid is the user running the delsesn command. Note that you can delete any user-session with this command.
Syntax
delsesn {<sesn no> | <sesn no> <sesn no> .... | all }
Syntax Description
sesn no
The session number has a range of 1-15. You can specify one session, a series of user sessions, or all user sessions. The dspsesn command displays the user-session numbers.
Related Commands
dspsesn, who
Attributes
Example
Use the dspsesn command to determine the existing user-sessions. Delete session 2 (user "david9"), then repeat the dspsesn command. Note that the dspsesn output provides a form of the user-session number that delsesn requires: "Session 2."
M8850_NY.7.PXM.a > M8850_NY.7.PXM.a > dspsesnPort Slot Idle UserId From-------------------------------------------------------------telnet.01 * 7 0:00:00 david 10.19.238.35telnet.02 7 0:00:18 david9 10.19.238.35M8850_NY.7.PXM.a > M8850_NY.7.PXM.a > dspsesn-----------------------------------------> Session 0 (console):Waiting for login...-----------------------------------------*> Session 1 (telnet):Executing command: dspsesnuser name: davidaccess level: SERVICE_GPslot: 7slotFallback: 1From: 10.19.238.35-----------------------------------------> Session 2 (telnet):Waiting for user input...user name: david9access level: GROUP1slot: 7slotFallback: 7From: 10.19.238.35M8850_NY.7.PXM.a > delsesn 2WARNING! delsesn is a destructive command it willnon-gracefully delete sessions selected by youDo you wish to proceed ? [y/n] yM8850_NY.7.PXM.a > dspsesn-----------------------------------------> Session 0 (console):Waiting for login...-----------------------------------------*> Session 1 (telnet):Executing command: dspsesnuser name: davidaccess level: SERVICE_GPslot: 7slotFallback: 1From: 10.19.238.35delsigdiag
Delete Signaling Diagnostic—PXM45, PXM1E
Removes a signaling diagnostics filter table entry or removes some configuration values within a filter table entry.
Syntax
delsigdiag [index] [-cldaddr nsap-address] [-clgaddr nsap-address] [-cldaddrmask {yes | no}] [-clgaddrmask {yes | no}] [-casttype {yes | no}] [-clrcause {yes | no}] [-connctgy {yes | no}] [-inport {yes | no}] [-outport {yes | no}] [-maxrec {yes | no}] [-scope {yes | no}] [-servctgy {yes | no}]
Syntax Description
Related Commands
cnfsigdiag, delsigdiag, dspsigstats, clrsigstats
Attributes
delslotlink
Delete Slot Link—PXM1E
The delslotlink command lets you delete either one link or all links between an SRM and a service module. See the addlink description for details on bulk mode distribution.
Syntax
delslotlink <SM SlotNum> < SM LineNum>
Syntax Description
Related Commands
addlink, cnflink, dsplink, dspslotlink
Attributes
delsntprmtsvr
Delete SNTP Remote Server-—PXM45, PXM1E
The delsntprmtsvr command lets you delete the role of a remote switch as an SNTP server. Alternatively, you can delete all servers from the list of SNTP servers.
Syntax
delsntprmtsvr {server IP address} | all
Syntax Description
server IP address
all
Specify the IP address of one switch to remove it from the list of servers, or type "all" to clear the entire list of servers.
Related Commands
addsntprmtsvr, cnfsntprmtsvr, dspsntprmtsvr, dspsntp, cnfsntp
Attributes
deltopond
Delete Node From Persistent Topology Database—PXM45, PXM1E
The deltopond command deletes a single node from the persistent topology database.
Syntax
deltopond <nodeIndex>
Syntax Description
nodeIndex
Provide the current node's index to delete it from the persistent topology database. To see a list of all indexes and nodes, use the dsptopondlist command.
Related Command
cnftopogw, dsptopogw, dsptopogwndlist, dsptopondlist
Attributes
deltrapmgr
Delete Trap Manager—PXM45, PXM1E
Delete a trap manager. The deltrapmgr command requires an IP address for deletion. To see existing trap managers, use dsptrapmgr.
For more information about trap managers, see one of the following documentation sources:
•
•
•
Syntax
deltrapmgr <ip_addr>
Syntax Description
Related Commands
addtrapmgr, dsptrapmgr
Attributes
Example
Delete trap manager with IP address 161.10.144.56.
node501.7.PXM.a > deltrapmgr 161.10.144.56deluser
Delete User—PXM45, PXM1E
Removes a user from the list of users on a node. The system does not allow you to delete a user with a privilege level higher than the level at which you execute the command. For example, if the current user privilege is 2 (GROUP2), you cannot delete a user at level 1 (GROUP1). See the adduser description for the user-privilege hierarchy. No screen output appears unless an error occurs.
Syntax
deluser <user ID>
Syntax Description
Related Commands
dspusers, adduser
Attributes
disablesscop
Disable SSCOP—PXM45
The disablesscop command lets you disable SSCOP on a port. The port must be administratively down (by the dnpnport command). Be sure a valid and useful reason exists for disabling SSCOP.
Syntax
disablesscop <portid> {yes | no}
Syntax Description
portid
The format of the PNNI physical port identifier can vary, as follows:
•
•
–
–
•
For more details, see the section, "PNNI Format," in "Introduction."
yes or
noThe choice for disabling or enabling SSCOP on the port:
•
•
Default: no (enable SSCOP on the specified port)
Related Commands
cnfsscop, dspsscop, dspsscopstats
Attributes
Example
Disable SSCOP on port 11:2.8:28.
Geneva.7.PXM.a > disablesscop 11:2.8:28 yesGeneva.7.PXM.a >dncon
Down Connection—PXM1E
Administratively deactivates (or "downs") so you can modify or troubleshoot the network. This operation applies to only SPVCs. To reactivate the connection, use upcon.
Syntax
dncon <ifNum> <vpi> <vci>
Syntax Description
Related Commands
upcon
Attributes
dnimagrp
Down IMA Group—PXM1E
This command administratively disables an IMA group.
The order of commands for downing and upping an IMA group is as follows:
1.
2.
3.
Syntax
dnimagrp <group>
Syntax Description
group
The group identifier consists of a bay number as well as a group number in the format bay.group, as follows:
•
•
Related Commands
upimagrp
Attributes
Example
Disable IMA group number 16.
MGX8850.7.PXM1E.a > dnimagrp 2.16dnilmi
Down ILMI—PXM1E
The dnilmi command lets you de-activate (down) ILMI on a logical port so you can modify a configuration, troubleshoot, or run certain commands that require ILMI to be inoperative.
Syntax
dnilmi <ifNum> <partId>
Syntax Description
ifNum
The range for logical interface (or port) numbers is are as follows 1-31.
partId
The range for partition ID is 1-20.
Related Commands
dspilmi, dspilmis, upilmi
Attributes
dnln
Down Line—PXM45, PXM1E
On a PXM1E, the dnln command de-activates a line on one of two different card types. The line can be on the PXM1E UNI/NNI back card or on a service resource module (SRME or SRM-3T3). A dnln command also runs on the AXSMs in a switch with a PXM45. See the other dnln description for details.
Note
Syntax
dnln <X>.<line>
Syntax Description
Related Commands
dspln, dsplns, cnfln, upln
Attributes
Example
Down line 1 on the back card of the PXM1E.
MGX8850.7.PXM1E.a > dnln 2.1dnpnport
Down PNNI Port—PXM45, PXM1E
The dnpnport command takes a UNI or NNI port out of service (administratively "downs" a port). For example, downing a port is necessary for certain provisioning activity or maintenance activity. Where appropriate, the applicable commands state that you must down a port by using dnpnport.
Note
Syntax
dnpnport <portid>
Syntax Description
portid
The format of the PNNI physical port identifier can vary, as follows:
•
•
–
–
•
For more details, see the section, "PNNI Format," in "Introduction."
Related Commands
addpnport, delpnport, uppnport, dsppnport
Attributes
Examples
Remove port 11:2.8:22 from service.
Geneva.7.PXM.a > dnpnport 11:2.8:28Geneva.7.PXM.a >dnport
Down Port—PXM1E
The dnport command disables (or downs) a logical port and thereby halts all traffic on the logical port. The usual purpose for using dnport is troubleshooting. The configuration for the port remains intact whether the logical port is a UNI or an NNI. The command for enabling a downed port is upport.
For an NNI, the PXM de-routes the failed connections then re-routes them through other trunks. After you re-enable an NNI port through upport, you cannot return the re-routed connections to the upped port. The PXM routes connections over the trunk as needed.
On a UNI, the connections continue to exist, but remain in the failed state until you enable the port by executing upport.
Caution
Syntax
dnport <ifNum>
Syntax Description
ifNum
The range for logical interface (or port) numbers is 1-31.
Use dspports or dspport as needed to determine the need to disable a port.
Related Commands
dspport, dspports, upport
Attributes
Example
Disable port 1 on the current card.
MGX8850.7.PXM1E.a > dnport 1downloadflash
Download Flash—PXM45, PXM1E
The downloadflash command does not execute at the runtime prompt. It operates in bootmode only.
A downloadflash session concludes the sequence of tasks for performing a PXM boot code load. Prior to executing this command, you must access the boot code and transfer the file to the PXM hard drive by using a "put" command). Arguments within the "put" command let you load boot code to any combination of standby or active PXMs. (See Example section for details.) Once firmware is installed in slot 7, the bootcode is mirrored to a new PXM in slot 8 if present. However, to ensure that the boot code is correct, use downloadflash as a manual way to download the boot code to the standby PXM.
Note
Syntax
downloadflash
Related Commands
None
Attributes
Example
Do a PXM45 boot code load. Start with a tftp to the boot code source. Conclude with the download to the standby and the active PXM45. Despite the ".fw" argument in the command string, this is NOT a firmware load. The first lines show an attempt to run downloadflash within the runtime image.
Unknown.7.PXM.a > downloadflashError: flash_file supported only at backup boot> ftp <switch_dest_addr> > bin > put <pxm_bkup_version>.fw PINNACLE@PXM45.BT > quitwilco.7.PXM.a > downloadflash•
>put pxm_bkup_version>.fw PINNACLE@PXM45_ACTIVE.BT•
>put pxm_bkup_version>.fw PINNACLE@PXM45_STANDBY.BT
