Cisco 819 Integrated Services Routers Software Configuration Guide

Step 1

vpdn enable

Example:

Enables VPDN on the router.

Step 2

vpdn-group name

Example:

Creates and associates a VPDN group with a customer or VPDN profile.

Step 3

request-dialin

Example:

Creates a request-dialin VPDN subgroup, indicating the dialing direction, and initiates the tunnel.

Step 4

protocol { l2tp | pppoe }

Example:

Specifies the type of sessions the VPDN subgroup can establish.

Step 5

exit

Example:

Exits request-dialin VPDN group configuration.

Step 6

exit

Example:

Exits VPDN configuration, returning to global configuration mode.

Step 1

interface type number

Example:

Enters interface configuration mode for a Fast Ethernet WAN interface.

Step 2

pppoe-client dial-pool-number number

Example:

Configures the PPPoE client and specifies the dialer interface to use for cloning.

Step 3

no shutdown

Example:

Enables the Fast Ethernet interface and the configuration changes just made to it.

Step 4

exit

Example:

Exits configuration mode for the Fast Ethernet interface and returns to global configuration mode.

Step 1

interface dialer dialer-rotary-group-number

Example:

Creates a dialer interface (numbered 0 to 255) and enters interface configuration mode.

Step 2

ip address negotiated

Example:

Specifies that the IP address for the interface is obtained through PPP/IPCP (IP Control Protocol) address negotiation.

Step 3

ip mtu bytes

Example:

Sets the size of the IP maximum transmission unit (MTU). The default minimum is 128 bytes. The maximum for Ethernet is 1492 bytes.

Step 4

encapsulation encapsulation-type

Example:

Sets the encapsulation type to PPP for the data packets being transmitted and received.

Step 5

ppp authentication {protocol1 [protocol2...]}

Example:

Sets the PPP authentication method to Challenge Handshake Authentication Protocol (CHAP).

For details about this command and additional parameters that can be set, see Cisco IOS Security Command Reference.

Step 6

dialer pool number

Example:

Specifies the dialer pool to use to connect to a specific destination subnetwork.

Step 7

dialer-group group-number

Example:

Assigns the dialer interface to a dialer group (1 to 10).

Step 8

exit

Example:

Exits the dialer 0 interface configuration.

Step 9

dialer-list dialer-group protocol protocol-name {permit | deny | list access-list-number | access-group}

Example:

Creates a dialer list and associates a dial group with it. Packets are then forwarded through the specified interface dialer group.

For details about this command and additional parameters that can be set, see Cisco IOS Dial Technologies Command Reference.

Step 10

ip route prefix mask {interface-type interface-number}

Example:

Sets the IP route for the default gateway for the dialer 0 interface.

For details about this command and additional parameters that can be set, see Cisco IOS IP Command Reference, Volume 2 of 3: Routing Protocols, Release 12.2 and Cisco IOS IP Command Reference, Volume 2 of 4: Routing Protocols, Release 12.3.

Step 1

ip nat pool name start-ip end-ip {netmask netmask | prefix-length prefix-length}

Example:

Creates pool of global IP addresses for NAT.

Step 2

ip nat inside source {list access-list-number} {interface type number | pool name} [overload]

Example:

or

Example:

Enables dynamic translation of addresses on the inside interface.

The first example shows the addresses permitted by the access list 1 to be translated to one of the addresses specified in the dialer interface 0.

The second example shows the addresses permitted by access list acl1 to be translated to one of the addresses specified in the NAT pool pool1.

For details about this command and additional parameters that can be set, as well as information about enabling static translation, see Cisco IOS IP Command Reference, Volume 1 of 4: Addressing and Services.

Step 3

interface type number

Example:

Enters configuration mode for the VLAN (on which the Fast Ethernet LAN interfaces [FE0–FE3] reside) to be the inside interface for NAT.

Step 4

ip nat { inside | outside }

Example:

Identifies the specified VLAN interface as the NAT inside interface.

For details about this command and additional parameters that can be set, as well as information about enabling static translation, see Cisco IOS IP Command Reference, Volume 1 of 4: Addressing and Services.

Step 5

no shutdown

Example:

Enables the configuration changes just made to the Ethernet interface.

Step 6

exit

Example:

Exits configuration mode for the Fast Ethernet interface.

Step 7

interface type number

Example:

Enters configuration mode for the Fast Ethernet WAN interface (FE4) to be the outside interface for NAT.

Step 8

ip nat { inside | outside }

Example:

Identifies the specified WAN interface as the NAT outside interface.

For details about this command and additional parameters that can be set, as well as information about enabling static translation, see Cisco IOS IP Command Reference, Volume 1 of 4: Addressing and Services.

Step 9

no shutdown

Example:

Enables the configuration changes just made to the Ethernet interface.

Step 10

exit

Example:

Exits configuration mode for the Fast Ethernet interface.

Step 11

access-list access-list-number {deny | permit} source [source-wildcard]

Example:

Defines a standard access list indicating which addresses need translation.

Note All other addresses are implicitly denied.