-
Cisco 7600 Series Router Cisco IOS Command Reference, 12.1E
-
Index
-
Preface
-
Command-Line Interface
-
action to cd
-
Cisco 7600 Series Router Cisco IOS Commands
-
BRC
-
channel-group to clear catalyst6000
-
clear counters to debug callback
-
debug cca to duplex
-
erase to mls aging
-
mls exclude to pagp port-priority
-
policy-map to protocol filtering
-
rcv-queue to show bootflash
-
shutdown vlan to time-range
-
show bootvar to show ip cache
-
show ip cef to show mls asic
-
show mls cef to show qm-sp
-
show queueing to show vtp
-
title
-
udld to username
-
verify to wrr-queue bandwidth
-
wrr-queue cos-map to wrr-queue threshold
-
Acronyms
-
Acknowledgments for Open-Source Software
-
Table Of Contents
show interfaces private-vlan mapping
22show bootvar
To display information about the BOOT environment variable, use the show bootvar command.
show bootvar
Syntax Description
This command has no keywords or arguments.
Defaults
This command has no default settings.
Command Modes
User EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
12.1(13)E
The output display was changed to include the DRAM installed on standby MSFC2.
Examples
This example shows how to display information about the BOOT environment variable:
Router> show bootvarBOOT variable = sup-bootflash:c6sup12-js-mz.121-13.E,12CONFIG_FILE variable =BOOTLDR variable = bootflash:c6msfc2-boot-mz.121-13.E.binConfiguration register is 0x2102Standby is upStandby has 112640K/18432K bytes of memory.Standby BOOT variable = bootflash:c6sup12-js-mz.121-13.E,12Standby CONFIG_FILE variable =Standby BOOTLDR variable = bootflash:c6msfc2-boot-mz.121-13.E.binStandby Configuration register is 0x2102Router>Related Commands
show cable-diagnostics prbs
To display the PBRS cable diagnostics test results, use the show cable-diagnostics prbs command.
show cable-diagnostics prbs {interface {interface interface-number}}
Syntax Description
interface interface
Interface type; the valid value is tengigabitethernet.
interface-number
Module and port number.
Defaults
This command has no default settings.
Command Modes
Privileged EXEC
Command History
12.1(19)E
Support for this command was introduced on the Cisco 7600 series routers.
Usage Guidelines
The show cable-diagnostics prbs command is supported on the 1-port 10GBASE-E serial 10-Gigabit Ethernet module (WS-X6502-10GE) only.
You can view the PRBS error counters only while the PRBS test is in progress. If the PRBS test has stopped running, N/A is displayed in the Error Counter field.
The PRBS error counter measures the reliability of the cable. The error counter range is 0 to 255. A value of 0 signifies a perfect link connection. A value of 255 signifies that the port is faulty or not connected or that there is no communication through the link. If the counter does not remain at zero for a predetermined length of time, the link is faulty. For example, for a baud error rate (BER) of 10^-12, the counter should remain at zero for 100 seconds.
Each time you access the PRBS counter by entering the show cable-diagnostics prbs command, the PRBS error counter value is reset to 0, and the counter begins to accumulate errors again.
Note
The PRBS counter is a "read and clear" register. The first reading in a sequence is usually unreliable and serves primarily to purge the counter; successive readings are accurate.
You must start the PRBS test on both ends of the cable and then read the error counter. If you start one end and read the error counter, a nonzero value counter is displayed, and a false alarm is generated.
Table 2-22 describes the fields in the show cable-diagnostics prbs command output.
Examples
This example shows how to display the PRBS test information:
Router> show cable-diagnostics prbs interface tengigabitethernet2/1PRBS error counter last cleared on 2003 04 15 - 15:52:25Time elapsed since last clear 00:00:12PRBS Max error counters = 255Interface PRBS State PRBS Error Counter----------- ------------ -------------------Te9/1 Start 0Related Commands
show cable-diagnostics tdr
To display the TDR cable diagnostics test results, use the show cable-diagnostics tdr command.
show cable-diagnostics tdr {interface {interface interface-number}}
Syntax Description
interface interface
Interface type; valid values are fastethernet and gigabitethernet.
interface-number
Module and port number.
Defaults
This command has no default settings.
Command Modes
Privileged EXEC
Command History
Usage Guidelines
The show cable-diagnostics tdr command is supported on the following modules only:
•
•
Table 2-23 describes the fields in the show cable-diagnostics tdr command output.
In the event of an open or shorted cable, the accuracy where the cable is open or shorted is plus or minus 2 meters.
The pair length can be displayed in meters, centimeters, or kilometers.
If the TDR test has not been run on the port, the following message is displayed:
TDR test was never run on Gi2/12Examples
This example shows how to display the TDR test information:
Router> show cable-diagnostics tdr interface gigabitethernet2/1TDR test last run on: April 25 12:48:15Interface Speed Local pair Pair length Remote pair Pair status---------- -------- ----------- ------------------- ------------ ------------Gi2/1 1000 Pair A 3 +/- 10 meters Pair B TerminatedPair B 3 +/- 10 meters Pair A TerminatedPair C 1 +/- 10 meters Pair C TerminatedPair D 0 +/- 10 meters Pair D TerminatedRouter>Related Commands
show catalyst6000
To display information about the Cisco 7600 series router, use the show catalyst6000 command.
show catalyst6000 {all | chassis-mac-address | switching-clock | traffic-meter}
Syntax Description
Defaults
all
Command Modes
EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Usage Guidelines
If you enter the switching-clock keywords, the system displays whether switching of the redundant clock sources on the backplane is allowed if the active clock source fails.
The Cisco 7600 series router chassis has either 64 or 1024 MAC addresses available to support software features like STP. You can enter the show catalyst6000 chassis-mac-address command to view the MAC address range on your chassis.
Examples
This example shows how to display chassis MAC address ranges and the current and peak traffic meter readings:
Router> show catalyst6000 allchassis MAC addresses: 1024 addresses from 00d0.004c.1800 to 00d0.004c.1c00traffic meter = 0% peak = 0% at 09:57:58 UTC Mon Nov 6 2000switching-clock: clock switchover and system reset is allowedRouter>This example shows how to display the range of chassis MAC addresses:
Router> show catalyst6000 chassis-mac-addresschassis MAC addresses: 1024 addresses from 00d0.004c.1800 to 00d0.004c.1c00Router>This example shows how to display current and peak traffic meter readings:
Router> show catalyst6000 traffic-metertraffic meter = 0% peak = 0% at 09:57:58 UTC Mon Nov 6 2000Router>This example shows how to display the switching clock failure recovery mode:
Router> show catalyst6000 switching-clockswitching-clock: clock switchover and system reset is allowedRouter>show cdp neighbors
To display detailed information about neighboring devices discovered using CDP, use the show cdp neighbors command.
show cdp neighbors [type number] [detail]
Syntax Description
Defaults
This command has no default settings.
Command Modes
Privileged EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Usage Guidelines
The port-channel values are from 0 to 282; values from 257 to 282 are supported on the CSM and the FWSM only.
Examples
This example shows sample output from the show cdp neighbors command:
Router# show cdp neighborsCapability Codes: R - Router, T - Trans Bridge, B - Source Route BridgeS - Switch, H - Host, I - IGMP, r - Repeater, P - PhoneDevice ID Local Intrfce Holdtme Capability Platform Port IDlab-7206 Eth 0 157 R 7206VXR Fas 0/0/0lab-as5300-1 Eth 0 163 R AS5300 Fas 0lab-as5300-2 Eth 0 159 R AS5300 Eth 0lab-as5300-3 Eth 0 122 R AS5300 Eth 0lab-as5300-4 Eth 0 132 R AS5300 Fas 0/0lab-3621 Eth 0 140 R S 3631-telcoFas 0/0008024 2758E0 Eth 0 132 T CAT3000 1/2Table 2-24 describes the fields shown in this example.
This example shows a sample output for the show cdp neighbors detail command:
Router# show cdp neighbors detail-------------------------Device ID: lab-7206Entry address(es):IP address: 172.19.169.83Platform: cisco 7206VXR, Capabilities: RouterInterface: Ethernet0, Port ID (outgoing port): FastEthernet0/0/0Holdtime : 123 secVersion :Cisco Internetwork Operating System SoftwareIOS (tm) 5800 Software (C5800-P4-M), Version 12.1(2)Copyright (c) 1986-2002 by Cisco Systems, Inc.advertisement version: 2Duplex: half-------------------------Device ID: lab-as5300-1Entry address(es):IP address: 172.19.169.87...Table 2-25 describes the field descriptions shown in the example.
Related Commands
show cdp (refer to the Cisco IOS Release 12.1 Command Reference)
show cdp entry (refer to the Cisco IOS Release 12.1 Command Reference)
show cdp interface (refer to the Cisco IOS Release 12.1 Command Reference)
show cdp traffic (refer to the Cisco IOS Release 12.1 Command Reference)show class-map
To display class-map information, use the show class-map command.
show class-map [class-name]
Syntax Description
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Examples
This example shows how to display class-map information for all class maps:
Router> show class-mapClass Map match-any class-default (id 0)Match anyClass Map match-any class-simple (id 2)Match anyClass Map match-all ipp5 (id 1)Match ip precedence 5Class Map match-all agg-2 (id 3)Router>This example shows how to display class-map information for a specific class map:
Router> show class-map ipp5Class Map match-all ipp5 (id 1)Match ip precedence 5Router>Related Commands
class-map
show policy-map
show policy-map interfaceshow counters interface
To display the interface counter information, use the show counters interface command.
show counters interface {type mod/port}
Syntax Description
type
Interface type; possible valid values are ethernet, fastethernet, gigabitethernet, tengigabitethernet, port-channel, pos, atm, null, tunnel, and ge-wan.
mod/port
Module and port number.
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
12.1(13)E
Support for this command was introduced on the Cisco 7600 series routers.
Usage Guidelines
The show counters interface command is not supported on SVIs.
Examples
This example shows how to display the traffic counter information:
Router# show counters interface fastethernet 5/264 bit counters:0. rxHCTotalPkts = 11. txHCTotalPkts = 12. rxHCUnicastPkts = 03. txHCUnicastPkts = 04. rxHCMulticastPkts = 05. txHCMulticastPkts = 06. rxHCBroadcastPkts = 17. txHCBroadcastPkts = 18. rxHCOctets = 789. txHCOctets = 7810. rxTxHCPkts64Octets = 011. rxTxHCPkts65to127Octets = 212. rxTxHCPkts128to255Octets = 013. rxTxHCPkts256to511Octets = 014. rxTxHCpkts512to1023Octets = 015. rxTxHCpkts1024to1518Octets = 016. txHCTrunkFrames = 017. rxHCTrunkFrames = 018. rxHCDropEvents = 032 bit counters:0. rxCRCAlignErrors = 01. rxUndersizedPkts = 02. rxOversizedPkts = 03. rxFragmentPkts = 04. rxJabbers = 05. txCollisions = 06. ifInErrors = 07. ifOutErrors = 08. ifInDiscards = 09. ifInUnknownProtos = 010. ifOutDiscards = 011. txDelayExceededDiscards = 012. txCRC = 013. linkChange = 114. wrongEncapFrames = 0All Port Counters1. InPackets = 12. InOctets = 783. InUcastPkts = 04. InMcastPkts = 05. InBcastPkts = 16. OutPackets = 17. OutOctets = 788. OutUcastPkts = 09. OutMcastPkts = 010. OutBcastPkts = 111. AlignErr = 012. FCSErr = 013. XmitErr = 014. RcvErr = 015. UnderSize = 016. SingleCol = 017. MultiCol = 018. LateCol = 019. ExcessiveCol = 020. CarrierSense = 021. Runts = 022. Giants = 023. InDiscards = 024. OutDiscards = 025. InErrors = 026. OutErrors = 027. TrunkFramesTx = 028. TrunkFramesRx = 029. WrongEncap = 030. Broadcast_suppression_discards = 031. Multicast_suppression_discards = 032. Unicast_suppression_discards = 033. rxTxHCPkts64Octets = 034. rxTxHCPkts65to127Octets = 235. rxTxHCPkts128to255Octets = 036. rxTxHCPkts256to511Octets = 037. rxTxHCpkts512to1023Octets = 038. rxTxHCpkts1024to1518Octets = 039. DropEvents = 040. CRCAlignErrors = 041. UndersizedPkts = 042. OversizedPkts = 043. FragmentPkts = 044. Jabbers = 045. Collisions = 046. DelayExceededDiscards = 047. bpduOutlost = 048. qos0Outlost = 049. qos1Outlost = 050. qos2Outlost = 051. qos3Outlost = 052. bpduCbicOutlost = 053. qos0CbicOutlost = 054. qos1CbicOutlost = 055. qos2CbicOutlost = 056. qos3CbicOutlost = 057. bpduInlost = 058. qos0Inlost = 059. qos1Inlost = 060. qos2Inlost = 061. qos3Inlost = 062. qos4Inlost = 063. qos5Inlost = 064. qos6Inlost = 065. qos7Inlost = 066. pqueInlost = 067. Overruns = 068. maxIndex = 0Router#show cwan
To display WAN statistics and information about the hidden VLAN-to-WAN interface, use the show cwan command.
show cwan {stats | vlans}
Syntax Description
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
Usage Guidelines
The show vlan internal command displays the internal VLANs allocated to OSM interfaces as L3-VLAN but does not display the associated subinterfaces.
Examples
This example shows how to display OSM statistical information:
Router> show cwan stats
0 unknown VLANs0 ATM packets with zero src_ltl or inactive VC0 unknown enctype0 output unknown enctype drops0 particle alloc failures0 pak alloc failuresRouter>This example shows how to display hidden VLAN-to-WAN interface mappings:
Router> show cwan vlans
Hidden VLAN swidb->if_number Interface-----------------------------------------------1017 75 ATM2/0/01018 90 ATM2/0/0.541019 92 ATM2/0/0.561020 93 ATM2/0/0.571021 94 ATM2/0/0.1001022 95 ATM2/0/0.1011023 96 ATM2/0/0.1021024 97 ATM2/0/0.1031025 98 ATM2/0/0.1101026 99 ATM2/0/0.1111027 100 ATM2/0/0.1121028 101 ATM2/0/0.1131029 102 ATM2/0/0.1201030 103 ATM2/0/0.2001031 104 ATM2/0/0.2011032 105 ATM2/0/0.2021033 106 ATM2/0/0.2031067 76 POS4/11068 77 POS4/21071 79 GE-WAN5/21072 80 GE-WAN5/31073 81 GE-WAN5/4Recycled VLAN Interface-----------------------------Pending recycle holdtime(ms) Interface-------------------------------------------Router>Related Commands
ip access-list hardware permit fragments
show diagnostic
To display information about the diagnostic test, use the show diagnostic command.
show diagnostic {{module {mod-num | all}} | level | {content module number}}
Syntax Description
Defaults
all
Command Modes
EXEC
Command History
12.1(11b)E
Support for this command was introduced on the Cisco 7600 series routers.
Usage Guidelines
If you do not enter a mod-num, the default is that information for all modules is displayed.
Examples
This example shows how to display the online diagnostic test results for a specific module:
Router> show diagnostic module 2Current Online Diagnostic Level = MinimalOnline Diagnostic Result for Module 2 : PASS Online Diagnostic Level when Line Card came up = MinimalTest Results: (. = Pass, F = Fail, U = Unknown)1 . TestLoopback :Port 1 2 ---------- . .2 . TestNewLearn : . 3 . TestIndexLearn : . 4 . TestDontLearn : . 5 . TestConditionalLearn : . 6 . TestBadBpdu : . 7 . TestTrap : . 8 . TestMatch : . 9 . TestCapture : . 10. TestProtocolMatch : . 11. TestChannel : . 12. TestIpFibShortcut : . 13. TestDontShortcut : . 14. TestL3Capture2 : . 15. TestL3VlanMet : . 16. TestTitanIngressSpan : . 17. TestTitanEgressSpan : . 18. TestAclPermit : . 19. TestAclDeny : . 20. TestNetflowInlineRewrite :Port 1 2 ---------- U URouter>This example shows how to display the current bootup diagnostic level:
Router> show diagnostic levelCurrent Online Diagnostic Level = CompleteRouter>This example shows how to display a list of online diagnostic tests for a specific module:
Router> show diagnostic content module 2Online Diagnostic Tests List for Module 2 :ID. Test Name Test Level --- ------------------------- ---------- 1 . TestLoopback Minimal 2 . TestNewLearn Minimal 3 . TestIndexLearn Minimal 4 . TestDontLearn Minimal 5 . TestConditionalLearn Minimal 6 . TestBadBpdu Minimal 7 . TestTrap Minimal 8 . TestMatch Minimal 9 . TestCapture Minimal 10. TestProtocolMatch Minimal 11. TestChannel Minimal 12. TestIpFibShortcut Minimal 13. TestDontShortcut Minimal 14. TestL3Capture2 Minimal 15. TestL3VlanMet Minimal 16. TestTitanIngressSpan Minimal 17. TestTitanEgressSpan Minimal 18. TestAclPermit Minimal 19. TestAclDeny Minimal 20. TestNetflowInlineRewrite Complete Router>Related Commands
show dot1q-tunnel
To display a list of dot1q tunnel-enabled ports, use the show dot1q-tunnel command.
show dot1q-tunnel [{interface interface interface-number}]
Syntax Description
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
Usage Guidelines
If you do not enter any keywords, the dot1q tunnel ports for all interfaces are displayed.
The interface-number argument designates the module and port number for the ethernet, fastethernet, gigabitethernet, tengigabitethernet, and ge-wan keywords. Valid values depend on the chassis and module used. For example, if you have a 48-port 10/100BASE-T Ethernet module installed in a 13-slot chassis, valid values for the slot number are from 2 to 13 and valid values for the port number are from 1 to 48.
The interface-number argument designates the port channel number for the port-channel keyword. For releases prior to Release 12.1(3a)E3, valid values are from 1 to 256; for Releases 12.1(3a)E3, 12.1(3a)E4, and 12.1(4)E1, valid values are from 1 to 64. Release 12.1(5c)EX and later support a maximum of 64 values ranging from 1 to 256. Release 12.1(13)E and later support a maximum of 64 values ranging from 1 to 282; values 257 to 282 are supported on the CSM and FWSM.
Examples
This example shows how to display dot1q tunneling status for a port channel:
Router> show dot1q-tunnel interface port-channel 10Interface---------Po10This display indicates that the port is up and has one dot1q tunnel configured on it.
Related Commands
switchport mode
vlan dot1q tag nativeshow dot1x
To display dot1x information, use the show dot1x command.
show dot1x {interface interface interface-number}
show dot1x {all | {statistics {interface interface interface-number}}}
Syntax Description
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
12.1(13)E
Support for this command was introduced on the Cisco 7600 series routers.
Usage Guidelines
When entering the show dot1x statistics command, you must enter interface interface interface-number for the command to perform correctly.
The interface-number argument designates the module and port number for the ethernet, fastethernet, gigabitethernet, tengigabitethernet, and ge-wan keywords. Valid values depend on the chassis and module used. For example, if you have a 48-port 10/100BASE-T Ethernet module installed in a 13-slot chassis, valid values for the slot number are from 2 to 13 and valid values for the port number are from 1 to 48.
Examples
This example shows how to display dot1x information for all interfaces:
Router> show dot1x interface fastethernet 5/1Default Dot1x Configuration Exists for this interface FastEthernet5/1AuthSM State = FORCE AUTHORIZEDBendSM State = IDLEPortStatus = AUTHORIZEDMaxReq = 2MultiHosts = DisabledPortControl = Force AuthorizedQuietPeriod = 60 SecondsRe-authentication = DisabledReAuthPeriod = 3600 SecondsServerTimeout = 30 SecondsSuppTimeout = 30 SecondsTxPeriod = 30 SecondsRouter>This example shows how to display dot1x information for all interfaces:
Router> show dot1x allDot1x Info for interface FastEthernet3/2 ---------------------------------------------------- AuthSM State = FORCE UNAUTHORIZED BendSM State = IDLE PortStatus = UNAUTHORIZED MaxReq = 2 MultiHosts = Disabled Port Control = Force UnAuthorized QuietPeriod = 60 Seconds Re-authentication = Disabled ReAuthPeriod = 3600 Seconds ServerTimeout = 30 Seconds SuppTimeout = 30 Seconds TxPeriod = 30 SecondsDot1x Info for interface FastEthernet3/12 ---------------------------------------------------- AuthSM State = Unknown State BendSM State = Unknown State PortStatus = UNKNOWN MaxReq = 2 MultiHosts = Disabled Port Control = Auto QuietPeriod = 60 Seconds Re-authentication = Disabled ReAuthPeriod = 3600 Seconds ServerTimeout = 30 Seconds SuppTimeout = 30 Seconds TxPeriod = 30 SecondsRouter>This example shows how to display dot1x statistical information for a port:
Router> show dot1x statistics interface fastethernet3/1 PortStatistics Parameters for Dot1x -------------------------------------------- TxReqId = 0 TxReq = 0 TxTotal = 0 RxStart = 0 RxLogoff = 0 RxRespId = 0 RxResp = 0 RxInvalid = 0 RxLenErr = 0 RxTotal= 0 RxVersion = 0 LastRxSrcMac 0000.0000.0000Router>show environment alarm
To display information about the environmental alarm, use the show environment alarm command.
show environment alarm [{status | threshold} [frutype]]
Syntax Description
Defaults
If you do not enter a frutype, all environmental alarm status information is displayed.
Command Modes
EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Usage Guidelines
Valid values for the frutype are as follows:
•
•
•
•
•
•
•
The slot argument designates the module and port number. Valid values for slot depend on the chassis and module used. For example, if you have a 48-port 10/100BASE-T Ethernet module installed in a 13-slot chassis, valid values for the slot number are from 2 to 13 and valid values for the port number are from 1 to 48.
Examples
This example shows how to display all environmental alarm status information:
Router> show environment alarm thresholdenvironmental alarm thresholds:power-supply 1 fan-fail: OKthreshold #1 for power-supply 1 fan-fail:(sensor value != 0) is system minor alarmpower-supply 1 power-output-fail: OKthreshold #1 for power-supply 1 power-output-fail:(sensor value != 0) is system minor alarmfantray fan operation sensor: OKthreshold #1 for fantray fan operation sensor:(sensor value != 0) is system minor alarmoperating clock count: 2threshold #1 for operating clock count:(sensor value < 2) is system minor alarmthreshold #2 for operating clock count:(sensor value < 1) is system major alarmoperating VTT count: 3threshold #1 for operating VTT count:(sensor value < 3) is system minor alarmthreshold #2 for operating VTT count:(sensor value < 2) is system major alarmVTT 1 OK: OKthreshold #1 for VTT 1 OK:(sensor value != 0) is system minor alarmVTT 2 OK: OKthreshold #1 for VTT 2 OK:(sensor value != 0) is system minor alarmVTT 3 OK: OKthreshold #1 for VTT 3 OK:(sensor value != 0) is system minor alarmclock 1 OK: OKthreshold #1 for clock 1 OK:(sensor value != 0) is system minor alarmclock 2 OK: OKthreshold #1 for clock 2 OK:(sensor value != 0) is system minor alarmmodule 1 power-output-fail: OKthreshold #1 for module 1 power-output-fail:(sensor value != 0) is system major alarmmodule 1 outlet temperature: 21Cthreshold #1 for module 1 outlet temperature:(sensor value > 60) is system minor alarmthreshold #2 for module 1 outlet temperature:(sensor value > 70) is system major alarmmodule 1 inlet temperature: 25Cthreshold #1 for module 1 inlet temperature:(sensor value > 60) is system minor alarmthreshold #2 for module 1 inlet temperature:(sensor value > 70) is system major alarmmodule 1 device-1 temperature: 30Cthreshold #1 for module 1 device-1 temperature:(sensor value > 60) is system minor alarmthreshold #2 for module 1 device-1 temperature:(sensor value > 70) is system major alarmmodule 1 device-2 temperature: 29Cthreshold #1 for module 1 device-2 temperature:(sensor value > 60) is system minor alarmthreshold #2 for module 1 device-2 temperature:(sensor value > 70) is system major alarmmodule 5 power-output-fail: OKthreshold #1 for module 5 power-output-fail:(sensor value != 0) is system major alarmmodule 5 outlet temperature: 26Cthreshold #1 for module 5 outlet temperature:(sensor value > 60) is system minor alarmthreshold #2 for module 5 outlet temperature:(sensor value > 75) is system major alarmmodule 5 inlet temperature: 23Cthreshold #1 for module 5 inlet temperature:(sensor value > 50) is system minor alarmthreshold #2 for module 5 inlet temperature:(sensor value > 65) is system major alarmEARL 1 outlet temperature: N/Othreshold #1 for EARL 1 outlet temperature:(sensor value > 60) is system minor alarmthreshold #2 for EARL 1 outlet temperature:(sensor value > 75) is system major alarmEARL 1 inlet temperature: N/Othreshold #1 for EARL 1 inlet temperature:(sensor value > 50) is system minor alarmthreshold #2 for EARL 1 inlet temperature:(sensor value > 65) is system major alarmRouter>Related Commands
show environment status
show environment temperatureshow environment status
To display information about the operational FRU status, use the show environment status command.
show environment status [frutype]
Syntax Description
Defaults
If you do not enter a frutype, all FRU status information is displayed.
Command Modes
EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Usage Guidelines
Valid values for the frutype are as follows:
•
•
•
•
•
•
•
•
•
•
The slot argument designates the module and port number. Valid values for slot depend on the chassis and module used. For example, if you have a 48-port 10/100BASE-T Ethernet module installed in a 13-slot chassis, valid values for the slot number are from 2 to 13 and valid values for the port number are from 1 to 48.
Examples
This example shows how to display all environment status information:
Router> show environment statusbackplane:operating clock count: 2operating VTT count: 3fan-tray:fantray fan operation sensor: OKVTT 1:VTT 1 OK: OKVTT 2:VTT 2 OK: OKVTT 3:VTT 3 OK: OKclock 1:clock 1 OK: OK, clock 1 clock-inuse: not-in-useclock 2:clock 2 OK: OK, clock 2 clock-inuse: in-usepower-supply 1:power-supply 1 fan-fail: OKpower-supply 1 power-output-fail: OKmodule 1:module 1 power-output-fail: OKmodule 1 outlet temperature: 21Cmodule 1 inlet temperature: 25Cmodule 1 device-1 temperature: 30Cmodule 1 device-2 temperature: 29CEARL 1 outlet temperature: N/OEARL 1 inlet temperature: N/Omodule 5:module 5 power-output-fail: OKmodule 5 outlet temperature: 26Cmodule 5 inlet temperature: 23Cmodule 5 device-1 temperature: 26Cmodule 5 device-2 temperature: 27CRouter>Table 2-26 lists the output field definitions.
Related Commands
show environment alarm
show environment temperatureshow environment temperature
To display current temperature readings, use the show environment temperature command.
show environment temperature [frutype]
Syntax Description
Defaults
If you do not enter a frutype, the module and EARL temperature readings are displayed.
Command Modes
EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Usage Guidelines
Valid values for the frutype are as follows:
•
•
•
•
•
The slot argument designates the module and port number. Valid values for slot depend on the chassis and module used. For example, if you have a 48-port 10/100BASE-T Ethernet module installed in a 13-slot chassis, valid values for the slot number are from 2 to 13 and valid values for the port number are from 1 to 48.
In the output display, the following applies:
•
•
•
Examples
This example shows how to display temperature information for a specific module:
Router> show environment temperature module 5module 5 outlet temperature: 26Cmodule 5 inlet temperature: 23CRouter>This example shows how to display temperature readings for all modules:
Router> show environment temperatureVTT 1 outlet temperature: 25CVTT 2 outlet temperature: 24CVTT 3 outlet temperature: 28Cmodule 1 outlet temperature: 24Cmodule 1 device-2 temperature: 29CRP 1 outlet temperature: 25CRP 1 inlet temperature: 29CEARL 1 outlet temperature: 25CEARL 1 inlet temperature: 22Cmodule 5 outlet temperature: 27Cmodule 5 inlet temperature: 22CRouter>Table 2-27 lists the output field definitions.
Related Commands
show environment alarm
show environment statusshow eobc
To display information about the EOBC interface, use the show eobc command.
show eobc
Syntax Description
This command has no keywords or arguments.
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Examples
This example shows how to display information about the EOBC interface:
Router> show eobcEOBC0/0 is up, line protocol is upHardware is DEC21143, address is 0000.2100.0000 (bia 0000.2100.0000)MTU 0 bytes, BW 100000 Kbit, DLY 100 usec,reliability 255/255, txload 1/255, rxload 1/255Encapsulation ARPA, loopback not setKeepalive not setUnknown duplex, Unknown Speed, MIIARP type: ARPA, ARP Timeout 04:00:00Last input never, output 00:00:00, output hang neverLast clearing of "show interface" counters neverQueueing strategy: fifoOutput queue 0/40, 0 drops; input queue 25/2147483647, 0 drops5 minute input rate 0 bits/sec, 0 packets/sec5 minute output rate 0 bits/sec, 0 packets/sec172196 packets input, 11912131 bytesReceived 0 broadcasts, 0 runts, 0 giants, 0 throttles0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored0 watchdog, 0 multicast0 input packets with dribble condition detected172144 packets output, 11363476 bytes, 0 underruns0 output errors, 0 collisions, 1 interface resets0 babbles, 0 late collision, 0 deferred0 lost carrier, 0 no carrier0 output buffer failures, 0 output buffers swapped outInterface EOBC0/0Hardware is DEC21143dec21140_ds=0x618FB938, registers=0x3C018000, ib=0x38A9180rx ring entries=128, tx ring entries=256, af setup failed=0rxring=0x38A9280, rxr shadow=0x618FBB20, rx_head=28, rx_tail=0txring=0x38A9AC0, txr shadow=0x618FBD4C, tx_head=72, tx_tail=72, tx_count=0PHY link upCSR0=0xF8024882, CSR1=0xFFFFFFFF, CSR2=0xFFFFFFFF, CSR3=0x38A9280CSR4=0x38A9AC0, CSR5=0xF0660000, CSR6=0x320CA002, CSR7=0xF3FFA261CSR8=0xE0000000, CSR9=0xFFFDC3FF, CSR10=0xFFFFFFFF, CSR11=0x0CSR12=0xC6, CSR13=0xFFFF0000, CSR14=0xFFFFFFFF, CSR15=0x8FF80000DEC21143 PCI registers:bus_no=0, device_no=6CFID=0x00191011, CFCS=0x02800006, CFRV=0x02000041, CFLT=0x0000FF00CBIO=0x20000801, CBMA=0x48018000, CFIT=0x28140120, CFDD=0x00000400MII registers:Register 0x00: FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFFRegister 0x08: FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFFRegister 0x10: FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFFRegister 0x18: FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFFthrottled=0, enabled=0, disabled=0rx_fifo_overflow=0, rx_no_enp=0, rx_discard=0tx_underrun_err=0, tx_jabber_timeout=0, tx_carrier_loss=0tx_no_carrier=0, tx_late_collision=0, tx_excess_coll=0tx_collision_cnt=0, tx_deferred=0, fatal_tx_err=0, tbl_overflow=0HW addr filter: 0x38D2EE0, ISL DisabledEntry= 0: Addr=0000.0000.0000Entry= 1: Addr=0000.0000.0000Entry= 2: Addr=0000.0000.0000Entry= 3: Addr=0000.0000.0000Entry= 4: Addr=0000.0000.0000Entry= 5: Addr=0000.0000.0000Entry= 6: Addr=0000.0000.0000Entry= 7: Addr=0000.0000.0000Entry= 8: Addr=0000.0000.0000Entry= 9: Addr=0000.0000.0000Entry=10: Addr=0000.0000.0000Entry=11: Addr=0000.0000.0000Entry=12: Addr=0000.0000.0000Entry=13: Addr=0000.0000.0000Entry=14: Addr=0000.0000.0000Entry=15: Addr=0000.2100.0000Router>This example shows how to display information about the EOBC interface, except for lines that contain the word output:
Router> show eobc | exclude outputEOBC0/0 is up, line protocol is upHardware is DEC21143, address is 0000.2100.0000 (bia 0000.2100.0000)MTU 0 bytes, BW 100000 Kbit, DLY 100 usec,reliability 255/255, txload 1/255, rxload 1/255Encapsulation ARPA, loopback not setKeepalive not setUnknown duplex, Unknown Speed, MIIARP type: ARPA, ARP Timeout 04:00:00Last clearing of "show interface" counters neverQueueing strategy: fifoOutput queue 0/40, 0 drops; input queue 25/2147483647, 0 drops5 minute input rate 0 bits/sec, 0 packets/sec175919 packets input, 12196443 bytesReceived 0 broadcasts, 0 runts, 0 giants, 0 throttles0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored0 watchdog, 0 multicast0 input packets with dribble condition detected0 babbles, 0 late collision, 0 deferred0 lost carrier, 0 no carrierInterface EOBC0/0Hardware is DEC21143dec21140_ds=0x618FB938, registers=0x3C018000, ib=0x38A9180rx ring entries=128, tx ring entries=256, af setup failed=0rxring=0x38A9280, rxr shadow=0x618FBB20, rx_head=7, rx_tail=0txring=0x38A9AC0, txr shadow=0x618FBD4C, tx_head=209, tx_tail=209, tx_count=0PHY link upCSR0=0xF8024882, CSR1=0xFFFFFFFF, CSR2=0xFFFFFFFF, CSR3=0x38A9280CSR4=0x38A9AC0, CSR5=0xF0660000, CSR6=0x320CA002, CSR7=0xF3FFA261CSR8=0xE0000000, CSR9=0xFFFDC3FF, CSR10=0xFFFFFFFF, CSR11=0x0CSR12=0xC6, CSR13=0xFFFF0000, CSR14=0xFFFFFFFF, CSR15=0x8FF80000DEC21143 PCI registers:bus_no=0, device_no=6CFID=0x00191011, CFCS=0x02800006, CFRV=0x02000041, CFLT=0x0000FF00CBIO=0x20000801, CBMA=0x48018000, CFIT=0x28140120, CFDD=0x00000400MII registers:Register 0x00: FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFFRegister 0x08: FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFFRegister 0x10: FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFFRegister 0x18: FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFFthrottled=0, enabled=0, disabled=0rx_fifo_overflow=0, rx_no_enp=0, rx_discard=0tx_underrun_err=0, tx_jabber_timeout=0, tx_carrier_loss=0tx_no_carrier=0, tx_late_collision=0, tx_excess_coll=0tx_collision_cnt=0, tx_deferred=0, fatal_tx_err=0, tbl_overflow=0HW addr filter: 0x38D2EE0, ISL DisabledEntry= 0: Addr=0000.0000.0000Entry= 1: Addr=0000.0000.0000Entry= 2: Addr=0000.0000.0000Entry= 3: Addr=0000.0000.0000Entry= 4: Addr=0000.0000.0000Entry= 5: Addr=0000.0000.0000Entry= 6: Addr=0000.0000.0000Entry= 7: Addr=0000.0000.0000Entry= 8: Addr=0000.0000.0000Entry= 9: Addr=0000.0000.0000Entry=10: Addr=0000.0000.0000Entry=11: Addr=0000.0000.0000Entry=12: Addr=0000.0000.0000Entry=13: Addr=0000.0000.0000Entry=14: Addr=0000.0000.0000Entry=15: Addr=0000.2100.0000Router>show errdisable detect
To display errdisable detection status, use the show errdisable detect command.
show errdisable detect
Syntax Description
This command has no keywords or arguments.
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Examples
This example shows how to display error disable detection status:
Router> show errdisable detectErrDisable Reason Detection status----------------- ----------------udld Enabledbpduguard Enabledrootguard Enabledpagp-flap Enableddtp-flap Enabledlink-flap EnabledRouter>Related Commands
show errdisable recovery
To display information about the errdisable recovery timer, use the show errdisable recovery command.
show errdisable recovery
Syntax Description
This command has no keywords or arguments.
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Examples
This example shows how to display information about the error disable recovery timer:
Router> show errdisable recoveryErrDisable Reason Timer Status----------------- --------------udld Enabledbpduguard Enabledsecurity-violatio Enabledchannel-misconfig Enabledpagp-flap Disableddtp-flap Disabledlink-flap Disabledl2ptguard Enabledpsecure-violation Enabledgbic-invalid Enableddhcp-rate-limit Enabledunicast-flood EnabledTimer interval:300 secondsInterfaces that will be enabled at the next timeout:Interface Errdisable reason Time left(sec)--------- ----------------- --------------Fa9/4 link-flap 279Related Commands
errdisable recovery
show interfaces statusshow etherchannel
To display EtherChannel information for a channel, use the show etherchannel command.
show etherchannel [channel-group] {port-channel | brief | detail | summary | port | load-balance | protocol}
Syntax Description
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
12.1(11b)EX
This command was changed to display protocol information.
Usage Guidelines
The number of valid values for channel-group depends on the software release. For releases prior to Release 12.1(3a)E3, valid values are from 1 to 256; for Releases 12.1(3a)E3, 12.1(3a)E4, and 12.1(4)E1, valid values are from 1 to 64. Release 12.1(5c)EX and later support a maximum of 64 values ranging from 1 to 256. Release 12.1(13)E and later support a maximum of 64 values ranging from 1 to 282; values 257 to 282 are supported on the CSM and FWSM.
If you do not specify a channel-group, all channel groups are displayed.
In the output, the Passive port list field is displayed for Layer 3 port channels only. This field means that the physical interface, which is still not up, is configured to be in the channel group (and indirectly is in the only port channel in the channel group).
In the show etherchannel protocol output if the interface is configured as part of the channel in mode ON, the command displays Protocol: - (Mode ON).
In the output of the show etherchannel summary command, the following guidelines apply:
•
•
Examples
This example shows how to display port-channel information for a specific group:
Router> show etherchannel 12 port-channelGroup: 12----------Port-channels in the group:----------------------Port-channel: Po1------------Age of the Port-channel = 143h:01m:12sLogical slot/port = 14/1 Number of ports = 2GC = - HotStandBy port = nullPort state = Port-channel Ag-InuseProtocol = LACPPorts in the Port-channel:Index Load Port EC state------+------+------+------------0 55 Fa4/1 active1 AA Fa4/2 activeTime since last port bundled: 16h:28m:58s Fa4/1Time since last port Un-bundled: 16h:29m:00s Fa4/4Router>This example shows how to display load-balancing information:
Router> show etherchannel load-balanceSource XOR Destination mac addressRouter>This example shows how to display a summary of information for a specific group:
Router> show etherchannel 1 briefGroup: 1----------Group state = L2Ports: 4 Maxports = 8Port-channels: 1 Max Port-channels = 1Protocol: LACPRouter>This example shows how to display detailed information for a specific group:
Router> show etherchannel 12 detailGroup state = L2Ports: 1 Maxports = 8Port-channels: 1 Max Port-channels = 1Protocol: PAgPPorts in the group:-------------------Port: Fa5/2------------Port state = Down Not-in-BndlChannel group = 12 Mode = Desirable-Sl Gcchange = 0Port-channel = null GC = 0x00000000 Pseudo port-channel = Po12Port index = 0 Load = 0x00 Protocol = PAgPFlags: S - Device is sending Slow LACPDUs F - Device is sending fast LACPDUsA - Device is in active mode P - Device is in passive modeLocal information:LACP Port Admin Oper Port PortPort Flags State Priority Key Key Number StateFa4/1 SA bndl 32768 100 100 0xc1 0x75Partner's information:Partner Partner PartnerPort System ID Port Number Age FlagsFa4/1 8000,00b0.c23e.d861 0x81 14s SPLACP Partner Partner PartnerPort Priority Oper Key Port State32768 128 0x81Age of the port in the current state: 16h:27m:42sPort-channels in the group:----------------------Port-channel: Po12------------Age of the Port-channel = 04d:02h:52m:26sLogical slot/port = 14/1 Number of ports = 0GC = 0x00000000 HotStandBy port = nullPort state = Port-channel Ag-Not-InuseProtocol = PAgPRouter>This example shows how to display a one-line summary per channel group:
Router> show etherchannel summaryFlags: D - down P - in port-channelI - stand-alone s - suspendedH - Hot-standby (LACP only)R - Layer3 S - Layer2U - in use f - failed to allocate aggregatorNumber of channel-groups in use: 2Number of aggregators: 2Group Port-channel Protocol Ports------+-------------+-----------+-----------------------------------------------12 Po12(SD) PAgP Fa5/2(D)24 Po24(RD) -Router>This example shows how to display EtherChannel port information for a specific group:
Router> show etherchannel 1 portChannel-group listing:-----------------------Group: 1----------Ports in the group:-------------------Port: Fa5/4------------Port state = EC-Enbld Down Not-in-Bndl Usr-ConfigChannel group = 1 Mode = Desirable Gcchange = 0Port-channel = null GC = 0x00000000 Psudo-agport = Po1Port index = 0 Load = 0x00 Protocol = LACPFlags: S - Device is sending Slow LACPDUs F - Device is sending fast LACPDUsA - Device is in active mode P - Device is in passive modeLocal information:LACP Port Admin Oper Port PortPort Flags State Priority Key Key Number StateFa5/4 SA bndl 32768 100 100 0xc1 0x75Partner's information:Partner Partner PartnerPort System ID Port Number Age FlagsFa5/4 8000,00b0.c23e.d861 0x81 14s SPLACP Partner Partner PartnerPort Priority Oper Key Port State32768 128 0x81Age of the port in the current state: 04d:02h:57m:38sRouter>This example shows how to display the protocol enabled:
Router> show etherchannel protocolChannel-group listing:-----------------------Group: 12----------Protocol: PAgPGroup: 24----------Protocol: - (Mode ON)Router>Related Commands
channel-group
channel-protocol
interface port-channelshow fabric
To display information about the crossbar fabric, use the show fabric command.
show fabric [active]
show fabric {channel-counters | errors | status} [slot | all]
show fabric switching-mode [module {slot | all}]
show fabric utilization [slot | all]
Syntax Description
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Supervisor Engine 2.
12.1(11b)E
This command was changed to include switching mode information.
Usage Guidelines
The show fabric utilization command is supported on switches configured with a Supervisor Engine 2 only.
To display all related crossbar fabric information, enter the show fabric command without keywords.
If you specify slot, the information is displayed for the specified slot. If you specify all, the information for all slots using the crossbar fabric is displayed. If you do not specify slot or all, the display is the same as if you entered all.
A fabric channel is each connection between a module and the crossbar fabric module. Each module can have zero, one, or two fabric channels. The more fabric channels a module has, the more overall bandwidth is available to the module.
The following errors are associated with crossbar fabrics:
•
•
•
The three types of fabric switching modes are as follows:
•
•
•
Threshold information is shown only when you enter the no fabric switching-mode allow truncated command.
Examples
This example shows how to display the module switching mode:
Router> show fabric switching-modeFabric module is required for system to operateModules are allowed to operate in bus modeTruncated mode is not allowed unless threshold is metThreshold for truncated mode operation is 2 SFM-capable cardsModule Slot Switching Mode1 Bus2 Crossbar3 Crossbar4 Bus5 No Interfaces7 DCEF9 DCEFThis example shows the display if you previously entered the fabric switching-mode allow truncated command:
Router> show fabric switching-mode allow truncatedFabric module is required for system to operateModules are allowed to operate in bus modeTruncated mode is allowedModule Slot Switching Mode1 Bus2 Crossbar3 Crossbar4 Bus5 No Interfaces7 DCEF9 DCEFThis example shows how to display the fabric channel status for all fabric-enabled channels:
Router> show fabric status allslot channel module fabricstatus status1 0 OK OKThis example shows how to display the percentage utilizations for all fabric-enabled channels:
Router> show fabric utilization allslot channel Ingress % Egress %1 0 0 0crc hbeat sync sync1 0 0 0 0 0show fm features
To display information about the general feature manager, use the show fm features command.
show fm features
Syntax Description
This command has no keywords or arguments.
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Examples
This example shows how to display information about the general feature manager:
Router> show fm featuresDesignated MSFC:1 Non-designated MSFC:1Redundancy Status:designatedInterface:FastEthernet2/10 IP is enabledhw[EGRESS] = 1, hw[INGRESS] = 1hw_force_default[EGRESS] = 0, hw_force_default[INGRESS] = 0mcast = 0priority = 2reflexive = 0inbound label:1protocol:ipfeature #:1feature id:FM_IP_ACCESSACL:106outbound label:2protocol:ipfeature #:1feature id:FM_IP_ACCESSACL:106Interface:FastEthernet2/26 IP is enabledhw[EGRESS] = 1, hw[INGRESS] = 0hw_force_default[EGRESS] = 0, hw_force_default[INGRESS] = 1mcast = 0priority = 2reflexive = 0inbound label:24protocol:ipfeature #:1feature id:FM_IP_ACCESSACL:113outbound label:3protocol:ipfeature #:1 featureid:FM_IP_WCCPService ID:0Service Type:0Interface:Vlan55 IP is enabledhw[EGRESS] = 1, hw[INGRESS] = 1hw_force_default[EGRESS] = 0, hw_force_default[INGRESS] = 0mcast = 0priority = 2reflexive = 0inbound label:4protocol:ipfeature #:1feature id:FM_IP_ACCESSACL:111Interface:Vlan101 IP is enabledhw[EGRESS] = 1, hw[INGRESS] = 1hw_force_default[EGRESS] = 0, hw_force_default[INGRESS] = 0mcast = 0priority = 2reflexive = 0inbound label:5protocol:ipfeature #:1feature id:FM_IP_ACCESSACL:101outbound label:6protocol:ipfeature #:1feature id:FM_IP_ACCESSACL:101Router>This example shows how to display lines of general feature manager information beginning with the line that begins with Redundancy:
Router> show fm features | begin RedundancyRedundancy Status: designatedRouter>show fm inband-counters
To display the number of inband packets that are sent by the MSFC for SLB and WCCP, use the show fm inband-counters command.
show fm inband-counters
Syntax Description
This command has no keywords or arguments.
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Usage Guidelines
The show fm inband-counters command output display includes the number of SLB inband packets sent and the number of WCCP inband packets sent.
If CBAC is configured, the display includes the number of packets sent for CBAC.
Examples
This example shows how to display the number of SLB and WCCP inband packets sent:
Router> show fm inband-countersInband Packets SentSlot WCCP SLB1 0 02 0 03 0 04 0 05 0 06 0 07 0 08 0 09 0 010 0 011 0 012 0 013 0 0Router>show fm insp
To display the list and status of the ACLs and ports on which CBAC is configured, use the show fm insp command.
show fm insp [detail]
Syntax Description
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Usage Guidelines
If you can configure a VACL on the port before you configure CBAC, the status displayed is INACTIVE; otherwise, it is ACTIVE. If PFC resources are exhausted, the command displays BRIDGE followed by the number of failed currently active NetFlow requests that have been sent to the MSFC2 for processing.
The show fm insp command output includes this information:
•
•
•
•
The detail option also displays the ACEs that are part of the ACL used for IP inspect on the given interface direction.
Examples
This example shows how to display the list and status of CBAC-configured ACLs and ports:
Router> show fm inspinterface:Vlan305(in) status :ACTIVEacl name:denyinterfaces:Vlan305(out):status ACTIVEshow fm interface
To display detailed information about the feature manager on a per-interface basis, use the show fm interface command.
show fm interface {{interface interface-number} | {null interface-number} | {port-channel number} | {vlan vlan-id}}
Syntax Description
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
Usage Guidelines
The interface-number argument designates the module and port number. Valid values for interface-number depend on the specified interface type and the chassis and module used. For example, if you specify a Gigabit Ethernet interface and have a 48-port 10/100BASE-T Ethernet module installed in a 13-slot chassis, valid values for the module number are from 2 to 13 and valid values for the port number are from 1 to 48.
The number of valid values for port-channel number depends on the software release. For releases prior to Release 12.1(3a)E3, valid values are from 1 to 256; for Releases 12.1(3a)E3, 12.1(3a)E4, and 12.1(4)E1, valid values are from 1 to 64. Release 12.1(5c)EX and later support a maximum of 64 values ranging from 1 to 256. Release 12.1(13)E and later support a maximum of 64 values ranging from 1 to 282; values 257 to 282 are supported on the CSM and FWSM.
If your system is configured with a Supervisor Engine 1, valid values for vlan-id are from 1 to 1005. If your system is configured with a Supervisor Engine 2, valid values for vlan-id are from 1 to 4094. Extended-range VLANs are not supported on systems configured with a Supervisor Engine 1.
Examples
This example shows how to display detailed information about the feature manager on a specified interface:
Router> show fm interface fastethernet 2/26Interface:FastEthernet2/26 IP is enabledhw[EGRESS] = 1, hw[INGRESS] = 0hw_force_default[EGRESS] = 0, hw_force_default[INGRESS] = 1mcast = 0priority = 2reflexive = 0inbound label:24protocol:ipfeature #:1feature id:FM_IP_ACCESSACL:113vmr IP value #1:0, 0, 0, 0, 0, 0, 0, 6 - 1vmr IP mask #1:0, 0, FFFF, FFFF, 0, 0, 0, FFvmr IP value #2:642D4122, 0, 0, 0, 1, 0, 0, 6 - 1vmr IP mask #2:FFFFFFFF, 0, 0, 0, 1, 0, 0, FFvmr IP value #3:0, 64020302, 0, 0, 6, 0, 0, 6 - 1vmr IP mask #3:0, FFFFFFFF, 0, 0, 6, 0, 0, FFvmr IP value #4:0, 64020302, 0, 0, A, 0, 0, 6 - 1vmr IP mask #4:0, FFFFFFFF, 0, 0, A, 0, 0, FFvmr IP value #5:0, 64020302, 0, 0, 12, 0, 0, 6 - 1vmr IP mask #5:0, FFFFFFFF, 0, 0, 12, 0, 0, FFvmr IP value #6:0, 0, 0, 0, 0, 0, 0, 0 - 2vmr IP mask #6:0, 0, 0, 0, 0, 0, 0, 0outbound label:3protocol:ipfeature #:1feature id:FM_IP_WCCPService ID:0Service Type:0Router>show fm reflexive
To display information about the dynamic feature manager reflexive entry, use the show fm reflexive command.
show fm reflexive
Syntax Description
This command has no keywords or arguments.
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Examples
This example shows how to display information about the dynamic feature manager reflexive entry:
Router> show fm reflexiveReflexive hash table:Vlan613:refacl, OUT-REF, 64060E0A, 64060D0A, 0, 0, 7, 783, 6Router>show fm summary
To display a summary of feature manager information, use the show fm summary command.
show fm summary
Syntax Description
This command has no keywords or arguments.
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
12.1(8a)EX
The output display was changed to include ACL merge algorithm information.
Examples
This example shows how to display a summary of feature manager information:
Router> show fm summaryCurrent global ACL merge algorithm:BDDInterface:FastEthernet2/10ACL merge algorithm used:inbound direction: ODMoutbound direction:BDDTCAM screening for features is ACTIVE outboundTCAM screening for features is ACTIVE inboundInterface:FastEthernet2/26ACL merge algorithm used:inbound direction: ODMoutbound direction:BDDTCAM screening for features is ACTIVE outboundTCAM screening for features is INACTIVE inbound...Router>show fm vlan
To display information about the per-VLAN feature manager, use the show fm vlan command.
show fm vlan vlan-id
Syntax Description
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
Usage Guidelines
If your system is configured with a Supervisor Engine 1, valid values for vlan-id are from 1 to 1005. If your system is configured with a Supervisor Engine 2, valid values for vlan-id are from 1 to 4094. Extended-range VLANs are not supported on systems configured with a Supervisor Engine 1.
Examples
This example shows how to display information about the per-VLAN feature manager:
Router> show fm vlan 1hw[EGRESS] = 1, hw[INGRESS] = 1hw_force_default[EGRESS] = 0, hw_force_default[INGRESS] = 0mcast = 0priority = 2reflexive = 0vacc_map : map1inbound label: 5merge_err: 0protocol: ipfeature #: 1feature id: FM_VACLmap_name: map1seq #: 10(only for IP_PROT) DestAddr SrcAddr Dpt Spt L4OP TOS Est prot Rsltvmr IP value # 1: 0.0.0.0 0.0.0.0 0 0 0 0 0 6 permitvmr IP mask # 1: 0.0.0.0 0.0.0.0 0 0 0 0 0 FFvmr IP value # 2: 0.0.0.0 0.0.0.0 0 0 0 0 0 11 permitvmr IP mask # 2: 0.0.0.0 0.0.0.0 0 0 0 0 0 FFvmr IP value # 3: 0.0.0.0 0.0.0.0 0 0 0 0 0 0 denyvmr IP mask # 3: 0.0.0.0 0.0.0.0 0 0 0 0 0 0seq #: 65536(only for IP_PROT) DestAddr SrcAddr Dpt Spt L4OP TOS Est prot Rsltvmr IP value # 1: 0.0.0.0 0.0.0.0 0 0 0 0 0 0 permitvmr IP mask # 1: 0.0.0.0 0.0.0.0 0 0 0 0 0 0outbound label: 6merge_err: 0protocol: ipfeature #: 1feature id: FM_VACLmap_name: map1seq #: 10(only for IP_PROT) DestAddr SrcAddr Dpt Spt L4OP TOS Est prot Rsltvmr IP value # 1: 0.0.0.0 0.0.0.0 0 0 0 0 0 6 permitvmr IP mask # 1: 0.0.0.0 0.0.0.0 0 0 0 0 0 FFvmr IP value # 2: 0.0.0.0 0.0.0.0 0 0 0 0 0 11 permitvmr IP mask # 2: 0.0.0.0 0.0.0.0 0 0 0 0 0 FFvmr IP value # 3: 0.0.0.0 0.0.0.0 0 0 0 0 0 0 denyvmr IP mask # 3: 0.0.0.0 0.0.0.0 0 0 0 0 0 0seq #: 65536(only for IP_PROT) DestAddr SrcAddr Dpt Spt L4OP TOS Est prot Rsltvmr IP value # 1: 0.0.0.0 0.0.0.0 0 0 0 0 0 0 permitvmr IP mask # 1: 0.0.0.0 0.0.0.0 0 0 0 0 0 0show icc
To display information about the ICC counter and status, use the show icc command.
show icc {counters | status}
Syntax Description
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Examples
This example shows how to display information about the ICC counter:
Router> show icc counterstotal tx RPC packets to slot 1 LCP = 0detail by request id: (<request-id>=<number-of-packets>)2 =0 7 =0 8 =0 10=011=0 12=0 14=0 17=018=0 19=0 20=0total rx RPC packets from slot 1 LCP = 0detail by request id: (<request-id>=<number-of-packets>)2 =5 7 =7 8 =11 10=411=1 12=2 14=1 17=6718=7 19=159 20=29total tx MCAST-SP packets to slot 1 LCP = 0detail by request id: (<request-id>=<number-of-packets>)6 =0 7 =0 8 =0 9 =012=0 14=0total rx MCAST-SP packets from slot 1 LCP = 0detail by request id: (<request-id>=<number-of-packets>)6 =1 7 =1 8 =1 9 =112=41 14=67total tx L3-MGR packets to slot 1 LCP = 0detail by request id: (<request-id>=<number-of-packets>)1 =0 2 =0 3 =0total rx L3-MGR packets from slot 1 LCP = 0detail by request id: (<request-id>=<number-of-packets>)1 =1 2 =2 3 =1Router>This example shows how to display information about the ICC status:
Router> show icc statusClass Name Msgs Pending Max Pending Total Sent----- ---------------- ------------ ----------- ----------2 RPC 0 3 4033 MSC 0 1 15 L3-MGR 0 4 417313 TCAM-API 0 10 26Router>show idprom
To display IDPROMs for FRUs, use the show idprom command.
show idprom {all | frutype | {interface interface slot}} [detail]
Syntax Description
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
12.1(13.5)E1
This command was changed to include the interface interface slot option.
Usage Guidelines
Valid frutypes are as follows:
•
•
•
•
•
•
•
•
The slot argument designates the module and port number. Valid values for slot depend on the specified interface type and the chassis and module used. For example, if you specify a Gigabit Ethernet interface and have a 48-port 10/100BASE-T Ethernet module installed in a 13-slot chassis, valid values for the module number are from 2 to 13 and valid values for the port number are from 1 to 48.
Use the show idprom backplane command to display the chassis serial number.
The interface interface slot option is supported on GBIC security-enabled interfaces only.
Examples
This example shows how to display IDPROM information for clock 1:
Router> show idprom clock 1IDPROM for clock #1(FRU is 'Clock FRU')OEM String = 'Cisco Systems'Product Number = 'WS-C6000-CL'Serial Number = 'SMT03073115'Manufacturing Assembly Number = '73-3047-04'Manufacturing Assembly Revision = 'A0'Hardware Revision = 1.0Current supplied (+) or consumed (-) = 0.000ARouter>This example shows how to display IDPROM information for power supply 1:
Router> show idprom power-supply 1IDPROM for power-supply #1(FRU is '110/220v AC power supply, 1360 watt')OEM String = 'Cisco Systems, Inc.'Product Number = 'WS-CAC-1300W'Serial Number = 'ACP03020001'Manufacturing Assembly Number = '34-0918-01'Manufacturing Assembly Revision = 'A0'Hardware Revision = 1.0Current supplied (+) or consumed (-) = 27.460ARouter>This example shows how to display detailed IDPROM information for power supply 1:
Router> show idprom power-supply 1 detailIDPROM for power-supply #1IDPROM image:(FRU is '110/220v AC power supply, 1360 watt')IDPROM image block #0:hexadecimal contents of block:00: AB AB 01 90 11 BE 01 00 00 02 AB 01 00 01 43 69 ..............Ci10: 73 63 6F 20 53 79 73 74 65 6D 73 2C 20 49 6E 63 sco Systems, Inc20: 2E 00 57 53 2D 43 41 43 2D 31 33 30 30 57 00 00 ..WS-CAC-1300W..30: 00 00 00 00 00 00 41 43 50 30 33 30 32 30 30 30 ......ACP030200040: 31 00 00 00 00 00 00 00 00 00 33 34 2D 30 39 31 1.........34-09150: 38 2D 30 31 00 00 00 00 00 00 41 30 00 00 00 00 8-01......A0....60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................70: 00 00 00 01 00 00 00 00 00 00 00 09 00 0C 00 03 ................80: 00 01 00 06 00 01 00 00 00 00 0A BA 00 00 00 00 ................block-signature = 0xABAB, block-version = 1,block-length = 144, block-checksum = 4542*** common-block ***IDPROM capacity (bytes) = 256 IDPROM block-count = 2FRU type = (0xAB01,1)OEM String = 'Cisco Systems, Inc.'Product Number = 'WS-CAC-1300W'Serial Number = 'ACP03020001'Manufacturing Assembly Number = '34-0918-01'Manufacturing Assembly Revision = 'A0'Hardware Revision = 1.0Manufacturing bits = 0x0 Engineering bits = 0x0SNMP OID = 9.12.3.1.6.1.0Power Consumption = 2746 centiamperes RMA failure code = 0-0-0-0*** end of common block ***IDPROM image block #1:hexadecimal contents of block:00: AB 01 01 14 02 5F 00 00 00 00 00 00 00 00 0A BA ....._..........10: 0A BA 00 16 ....block-signature = 0xAB01, block-version = 1,block-length = 20, block-checksum = 607*** power supply block ***feature-bits: 00000000 00000000rated current at 110v: 2746 rated current at 220v: 2746 (centiamperes)CISCO-STACK-MIB SNMP OID = 22 *** end of power supply block ***End of IDPROM imageRouter>This example shows how to display IDPROM information for the backplane:
Router> show idprom backplaneIDPROM for backplane #0(FRU is 'Catalyst 6000 9-slot backplane')OEM String = 'Cisco Systems'Product Number = 'WS-C6009'Serial Number = 'SCA030900JA'Manufacturing Assembly Number = '73-3046-04'Manufacturing Assembly Revision = 'A0'Hardware Revision = 1.0Current supplied (+) or consumed (-) = 0.000ARouter>show interfaces
To display traffic that is seen by a specific interface, use the show interfaces command.
show interfaces [{interface interface-number} | {null interface-number} | {vlan vlan-id}]
Syntax Description
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
Usage Guidelines
The interface-number argument designates the module and port number. Valid values for interface-number depend on the specified interface type and the chassis and module used. For example, if you specify a Gigabit Ethernet interface and have a 48-port 10/100BASE-T Ethernet module installed in a 13-slot chassis, valid values for the module number are from 2 to 13 and valid values for the port number are from 1 to 48.
If your system is configured with a Supervisor Engine 1, valid values for vlan-id are from 1 to 1005. If your system is configured with a Supervisor Engine 2, valid values for vlan-id are from 1 to 4094. Extended-range VLANs are not supported on systems configured with a Supervisor Engine 1.
Statistics are collected on a per-VLAN basis for Layer 2-switched packets and Layer 3-switched packets. Statistics are available for both unicast and multicast. The Layer 3-switched packet counts are available for both ingress and egress directions. The per-VLAN statistics are updated every 5 seconds.
In some cases, you might see a difference in the duplex mode displayed between the show interfaces command and the show running-config commands. In this case, the duplex mode displayed in the show interfaces command is the actual duplex mode the interface is running. The show interfaces command shows the operating mode for an interface, while the show running-config command shows the configured mode for an interface.
If you do not enter any keywords, all counters for all modules are displayed.
Examples
This example shows how to display traffic for a specific interface:
Router> show interfaces GigabitEthernet9/5GigabitEthernet9/5 is up, line protocol is upHardware is C6k 1000Mb 802.3, address is 0001.64f8.3fa5 (bia 0001.64f8.3fa5)Internet address is 172.20.20.20/24MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,reliability 255/255, txload 1/255, rxload 1/255Encapsulation ARPA, loopback not setKeepalive set (10 sec)Full-duplex, 1000Mb/sARP type: ARPA, ARP Timeout 04:00:00Last input 00:00:00, output never, output hang neverLast clearing of "show interface" counters neverQueueing strategy: fifoOutput queue 0/40, 0 drops; input queue 0/75, 0 drops5 minute input rate 1000 bits/sec, 2 packets/sec5 minute output rate 0 bits/sec, 0 packets/secL2 Switched: ucast: 8199 pkt, 1362060 bytes - mcast: 6980 pkt, 371952 bytesL3 in Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes mcastL3 out Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes300114 packets input, 27301436 bytes, 0 no bufferReceived 43458 broadcasts, 0 runts, 0 giants, 0 throttles0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored0 input packets with dribble condition detected15181 packets output, 1955836 bytes, 0 underruns0 output errors, 0 collisions, 3 interface resets0 babbles, 0 late collision, 0 deferred0 lost carrier, 0 no carrier0 output buffer failures, 0 output buffers swapped outRouter>show interfaces capabilities
To display the interface capabilities for a module, an interface, or all interfaces, use the show interfaces capabilities command.
show interfaces [interface interface-number] capabilities [{module number}]
Syntax Description
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
Usage Guidelines
The show interfaces capabilities command is not available for WAN ports or VLAN interfaces.
The interface-number argument designates the module and port number. Valid values for interface-number depend on the chassis and module used. For example, if you have a 48-port 10/100BASE-T Ethernet module installed in a 13-slot chassis, valid values for the slot number are from 2 to 13 and valid values for the port number are from 1 to 48.
Examples
This example shows how to display interface capabilities for a module:
Router> show interfaces capabilities module 1GigabitEthernet1/1Model: WS-X6K-SUP2-2GEType: No GBICSpeed: 1000Duplex: fullTrunk encap. type: 802.1Q,ISLTrunk mode: on,off,desirable,nonegotiateChannel: yesBroadcast suppression: percentage(0-100)Flowcontrol: rx-(off,on,desired),tx-(off,on,desired)Membership: staticFast Start: yesQOS scheduling: rx-(1p1q4t), tx-(1p2q2t)CoS rewrite: yesToS rewrite: yesInline power: noSPAN: source/destinationUDLD yesLink Debounce: yesLink Debounce Time: yesGigabitEthernet1/2Model: WS-X6K-SUP2-2GEType: No GBICSpeed: 1000Duplex: fullTrunk encap. type: 802.1Q,ISLTrunk mode: on,off,desirable,nonegotiateChannel: yesBroadcast suppression: percentage(0-100)Flowcontrol: rx-(off,on,desired),tx-(off,on,desired)Membership: staticFast Start: yesQOS scheduling: rx-(1p1q4t), tx-(1p2q2t)CoS rewrite: yesToS rewrite: yesInline power: noSPAN: source/destinationUDLD yesLink Debounce: yesLink Debounce Time: yesRouter>This example shows how to display interface capabilities for an interface:
Router> show interfaces fastethernet 4/1 capabilitiesFastEthernet4/1Model: WS-X6348-RJ-45Type: 10/100BaseTXSpeed: 10,100,autoDuplex: half,fullTrunk encap. type: 802.1Q,ISLTrunk mode: on,off,desirable,nonegotiateChannel: yesBroadcast suppression: percentage(0-100)Flowcontrol: rx-(off,on),tx-(none)Fast Start: yesQOS scheduling: rx-(1q4t), tx-(2q2t)CoS rewrite: yesToS rewrite: yesInline power: noSPAN: source/destinationUDLD yesLink Debounce: yesLink Debounce Time: noRouter>This example shows how to display port-channel interface capabilities:
Router> show interfaces port-channel 12 capabilitiesPort-channel12Model: NO IDPROMType: unknownSpeed: 10,100,1000,autoDuplex: half,fullTrunk encap. type: 802.1Q,ISLTrunk mode: on,off,desirable,nonegotiateChannel: yesBroadcast suppression: percentage(0-100)Flowcontrol: rx-(off,on),tx-(none)Fast Start: yesQOS scheduling: rx-(1q4t), tx-(1q4t)CoS rewrite: yesToS rewrite: yesInline power: noSPAN: source/destinationUDLD yesLink Debounce: yesLink Debounce Time: noRouter>
show interfaces counters
To display the traffic that the physical interface sees, use the show interfaces counters command.
show interfaces counters [errors | etherchannel | {module number} | {trunk [module number]}]
show interfaces [interface] counters {broadcast | etherchannel | multicast | unicast} [module number]
Syntax Description
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
Usage Guidelines
The show interfaces [interface] counters command displays the number of all of the packets arriving and includes the number of packets that may be dropped by the interface due to the storm-control settings.
If you do not enter any keywords, all counters for all modules are displayed.
When you enter the interface, these formats can be used:
•
•
You can define a single port range per command entry. If you specify a range of ports, the range must consist of the same slot and port type.
When you define a range, you must enter a white space between the first port and the hyphen (-) as follows:
show interfaces gigabitethernet7/1 -7 countersThe module number keyword and argument designate the module number and limits the display to interfaces on the module. Valid values depend on the chassis used. For example, if you have a 13-slot chassis, valid values for the module number are from 2 to 13.
Valid values for card-type are as follows:
•
•
•
•
•
The module number keyword and argument designate the module and port number. Valid values for number depend on the chassis and module used. For example, if you have a 48-port 10/100BASE-T Ethernet module installed in a 13-slot chassis, valid values for the module number are from 2 to 13 and valid values for the port number are from 1 to 48.
The outputs of the show interfaces {counters {broadcast | multicast | unicast} commands display the total discard count for all three suppression modes, not the discard count for each suppression mode.
If you enter the show interfaces [interface_id] counters command without entering the broadcast, multicast, or unicast option, the discard count is not displayed.
When you enter the show interface interface counters etherchannel command, follow these guidelines:
•
•
Examples
This example shows how to display error counters for a specific module:
Router> show interfaces counters errors module 1Port Align-Err FCS-Err Xmit-Err Rcv-Err UnderSizeGi1/1 0 0 0 0 0Gi1/2 0 0 0 0 0Port Single-Col Multi-Col Late-Col Excess-Col Carri-Sen Runts GiantsGi1/1 0 0 0 0 0 00Gi1/2 0 0 0 0 0 00Router>This example shows how to display traffic seen by a specific module:
Router> show interfaces counters module 1Port InOctets InUcastPkts InMcastPkts InBcastPktsGi1/1 0 0 0 0Gi1/2 0 0 0 0Port OutOctets OutUcastPkts OutMcastPkts OutBcastPktsGi1/1 0 0 0 0Gi1/2 0 0 0 0Router>This example shows how to display trunk counters for a specific module:
Router> show interfaces counters trunk module 1Port TrunkFramesTx TrunkFramesRx WrongEncapGi1/1 0 0 0Gi1/2 0 0 0Router>This example shows how to display the total discard count for all interfaces:
Router> show interfaces counters broadcastPort TotalSuppDiscardsGi1/1 32309122Gi1/2 0Fa3/1 7809Fa3/2 0Fa3/3 28773Fa3/4 995Fa3/5 0Fa3/6 0Fa3/7 0Fa3/8 0Fa3/9 0Fa3/10 72801Fa3/11 0Fa3/12 0Fa3/13 0Fa3/14 0Fa3/15 0Fa3/16 0Router>This example shows how to display the total discard count for a specific module:
Router> show interfaces counters multicast module 1Port TotalSuppDiscardsGi1/1 32309122Gi1/2 0Router>This example shows how to display the total discard count for a specific interface:
Router> show interfaces gigabitethernet1/1 counters unicastPort TotalSuppDiscardsGi1/1 32309122Router>show interfaces debounce
To display the debounce timer status and configuration, use the show interfaces debounce command.
show interfaces [{interface interface-number} | {null interface-number} | {vlan vlan-id}] debounce [module num]
Syntax Description
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
12.1(13)E
Support for this command was introduced on the Cisco 7600 series routers.
Usage Guidelines
The interface-number argument designates the module and port number. Valid values for interface-number depend on the specified interface type and the chassis and module used. For example, if you specify a Gigabit Ethernet interface and have a 48-port 10/100BASE-T Ethernet module installed in a 13-slot chassis, valid values for the module number are from 2 to 13 and valid values for the port number are from 1 to 48.
If your system is configured with a Supervisor Engine 1, valid values for vlan-id are from 1 to 1005. If your system is configured with a Supervisor Engine 2, valid values for vlan-id are from 1 to 4094. Extended-range VLANs are not supported on systems configured with a Supervisor Engine 1.
Examples
This example shows how to display the debounce configuration of an interface:
Router> show interfaces GigabitEthernet1/1 debouncePort Debounce time ValueGi1/1 enable 100Router>Related Commands
show interfaces description
To display a description and a status of an interface, use the show interfaces description command.
show interfaces [interface] description
Syntax Description
interface
(Optional) Interface type; for a list of valid values, see the "Usage Guidelines" section.
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Supervisor Engine 2.
12.1(11b)E
This command was changed to include the ge-wan, atm, and pos keywords.
Usage Guidelines
When you enter the interface value, these formats can be used:
•
•
You can define a single port range per command entry. If you specify a range of ports, the range must consist of the same slot and port type. When you define a range, you must enter a space before and after the hyphen (-) as follows:
show interfaces gigabitethernet7/1 - 7 counters broadcastPossible valid values for card-type are ethernet, fastethernet, gigabitethernet, tengigabitethernet, pos, atm, and ge-wan.
Examples
This example shows how to display information for all interfaces:
Router> show interfaces descriptionInterface Status Protocol DescriptionPO0/0 admin down down First POS interfacePO0/1 admin down downGi1/0 up up GigE to server farmRouter>Related Commands
description (refer to the Cisco IOS Release 12.1 Command Reference)
show interfaces flowcontrol
To display flow-control information, use the show interfaces flowcontrol command.
show interfaces [interface [mod]] flowcontrol [module number]
Syntax Description
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
Usage Guidelines
The mod argument designates the module and port number. Valid values for mod depend on the chassis and module used. For example, if you have a 48-port 10/100BASE-T Ethernet module installed in a 13-slot chassis, valid values for the slot number are from 2 to 13 and valid values for the port number are from 1 to 48.
The module number keyword and argument designate the module number and limits the display to interfaces on the module. Valid values depend on the chassis used. For example, if you have a 13-slot chassis, valid values for the module number are from 2 to 13.
Examples
This example shows how to display flow-control information for all interfaces:
Router> show interfaces flowcontrolPort Send FlowControl Receive FlowControl RxPause TxPauseadmin oper admin oper----- -------- -------- -------- -------- ------- -------Gi1/1 desired off off off 0 0Gi1/2 desired off off off 0 0Gi3/1 on on on on 0 0...Gi8/2 desired off off off 0 0Gi8/3 desired off off off 0 0Gi8/4 desired off off off 0 0Router>This example shows how to display flow-control information for a specific interface:
Router> show interfaces gigabitethernet 8/2 flowcontrolPort Send FlowControl Receive FlowControl RxPause TxPauseadmin oper admin oper----- -------- -------- -------- -------- ------- -------Gi8/2 desired off off off 0 0Router>Table 2-28 describes the fields in the show interfaces flowcontrol command output.
Related Commands
show interfaces private-vlan mapping
To display information about the PVLAN mapping for VLAN SVIs, use the show interfaces private-vlan mapping command.
show interfaces [interface interface-number] private-vlan mapping [active]
Syntax Description
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
12.1(8a)EX
Support for this command was introduced on the Cisco 7600 series routers.
Usage Guidelines
This command displays SVI information only.
The interface-number argument designates the module and port number. Valid values for interface-number depend on the chassis and module used. For example, if you have a 48-port 10/100BASE-T Ethernet module installed in a 13-slot chassis, valid values for the slot number are from 2 to 13 and valid values for the port number are from 1 to 48.
Examples
This example shows how to display information about the PVLAN mapping:
Router> show interfaces private-vlan mappingInterface Secondary VLAN Type--------- -------------- -----------------vlan2 301 communityvlan2 302 communityRouter>Related Commands
private-vlan
private-vlan mapping
show interfaces status
To display the interface status or a list of interfaces in an error-disabled state on LAN ports only, use the show interfaces status command.
show interfaces [interface interface-number] status [err-disabled | inactive | module number]
Syntax Description
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
12.1(19)E
This command was change to include the inactive option.
Usage Guidelines
The interface-number argument designates the module and port number. Valid values for interface-number depend on the chassis and module used. For example, if you have a 48-port 10/100BASE-T Ethernet module installed in a 13-slot chassis, valid values for the slot number are from 2 to 13 and valid values for the port number are from 1 to 48.
This command is supported on LAN ports only.
The module number keyword and argument designate the module number and limits the display to interfaces on the module. Valid values depend on the chassis used. For example, if you have a 13-slot chassis, valid values for the module number are from 2 to 13.
The show interfaces status inactive command displays the reason for the inactive status of an interface. If the port is not inactive, None is displayed in the Reason field.
Examples
This example shows how to display the status of all LAN ports:
Router> show interfaces statusPort Name Status Vlan Duplex Speed TypeGi1/1 disabled routed full 1000 missingGi1/2 notconnect 1 full 1000 unknown (4)Fa5/1 disabled routed auto auto 10/100BaseTXFa5/2 disabled routed auto auto 10/100BaseTXFa5/3 disabled routed auto auto 10/100BaseTXFa5/4 disabled routed auto auto 10/100BaseTXFa5/5 disabled routed auto auto 10/100BaseTXFa5/6 connected 10 a-full a-100 10/100BaseTXFa5/7 connected 10 a-full a-100 10/100BaseTXFa5/8 connected 200 a-half a-100 10/100BaseTXFa5/9 connected trunk a-full a-100 10/100BaseTXFa5/10 disabled routed auto auto 10/100BaseTXFa5/11 disabled routed auto auto 10/100BaseTXFa5/12 disabled routed auto auto 10/100BaseTXFa5/13 disabled routed auto auto 10/100BaseTXFa5/14 disabled routed auto auto 10/100BaseTXFa5/15 disabled routed auto auto 10/100BaseTXFa5/16 disabled routed auto auto 10/100BaseTXFa5/17 disabled routed auto auto 10/100BaseTXRouter>This example shows how to display the status of LAN ports in an error-disabled state:
Router> show interfaces status err-disabledPort Name Status ReasonFa9/4 notconnect link-flapinformational error message when the timer expires on a cause--------------------------------------------------------------5d04h:%PM-SP-4-ERR_RECOVER:Attempting to recover from link-flap err-disable state on Fa9/4Router>These examples show different displays for the show interfaces status inactive command:
Router> show interfaces f8/2 status inactivePort Name Status ReasonFa8/2 inactive remote-span-vlanRouter>Router> show interfaces f8/3 status inactivePort Name Status ReasonFa8/2 connected noneRouter>Related Commands
errdisable detect cause
show errdisable recoveryshow interfaces summary
To display a summary of statistics for all interfaces that are configured on a networking device, use the show interfaces summary command.
show interfaces summary [vlan]
Syntax Description
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Usage Guidelines
Separate counters for subinterfaces are not maintained and are not displayed in the show interfaces summary output.
Examples
This example shows how to display a summary of statistics for all interfaces that are configured on a networking device:
Router> show interfaces summary*: interface is upIHQ: pkts in input hold queue IQD: pkts dropped from input queueOHQ: pkts in output hold queue OQD: pkts dropped from output queueRXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)TRTL: throttle countInterface IHQ IQD OHQ OQD RXBS RXPS TXBS TXPS TRTL----------------------------------------------------------------------* FastEthernet0/0 0 0 0 0 0 0 0 0 0Serial0/0 0 0 0 0 0 0 0 0 0FastEthernet0/1 0 0 0 0 0 0 0 0 0Serial0/1 0 0 0 0 0 0 0 0 0Router>This example shows how to display the total number of VLAN interfaces:
Router> show interfaces summary vlanTotal number of Vlan interfaces: 7Vlan interfaces configured:1,5,20,2000,3000-3001,4000Router>show interfaces switchport
To display the administrative and operational status of a switching (nonrouting) port, use the show interfaces switchport command.
show interfaces [interface interface-number] switchport [module number]
Syntax Description
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
12.1(13)E
This command was changed to display multiple VLAN access port information.
Usage Guidelines
The interface-number designates the module and port number. Valid values depend on the chassis and module used. For example, if you have a 48-port 10/100BASE-T Ethernet module installed in a 13-slot chassis, valid values for the slot number are from 2 to 13 and valid values for the port number are from 1 to 48.
The module number keyword and argument designate the module number and limits the display to interfaces on the module. Valid values depend on the chassis used. For example, if you have a 13-slot chassis, valid values for the module number are from 2 to 13.
Examples
This example shows how to display switch-port information for module 1:
Router> show interfaces switchport module 1Name: Gi1/1Switchport: EnabledAdministrative Mode: private-vlan hostOperational Mode: downAdministrative Trunking Encapsulation: negotiateNegotiation of Trunking: OffAccess Mode VLAN: 2 ((Inactive))Trunking Native Mode VLAN: 1 (default)Private-vlan host-association: 18 20Private-vlan mapping: noneTrunking VLANs Enabled: ALLPruning VLANs Enabled: 2-1001Router>This example shows how to display switch-port information using the include output modifier:
Router> show interfaces switchport | include VLANName: Fa5/6Access Mode VLAN: 200 (VLAN0200)Trunking Native Mode VLAN: 1 (default)Trunking VLANs Enabled: ALLPruning VLANs Enabled: ALL...Router>This example shows how to display the configurations of two multiple VLAN access ports:
Router> show interfaces switchportName: Fa5/1Switchport: EnabledAdministrative Mode: accessOperational Mode: accessAdministrative Trunking Encapsulation: dot1qOperational Trunking Encapsulation: dot1qNegotiation of Trunking: offAccess Mode VLAN: 100Voice VLAN: 102Trunking Native Mode VLAN: 1 (default)Administrative private-vlan host-association: noneAdministrative private-vlan mapping: 900 ((Inactive)) 901 ((Inactive))Operational private-vlan: noneTrunking VLANs Enabled: ALLPruning VLANs Enabled: 2-1001Capture Mode DisabledCapture VLANs Allowed: ALLName: Fa5/2Switchport: EnabledAdministrative Mode: accessOperational Mode: downAdministrative Trunking Encapsulation: dot1qOperational Trunking Encapsulation: nativeNegotiation of Trunking: OffAccess Mode VLAN: 100Voice VLAN: 103 ((inactive))Trunking Native Mode VLAN: 1 (default)...Related Commands
show interfaces trunk
To display the interface-trunk information, use the show interfaces trunk command.
show interfaces [interface interface-number] trunk [module number]
Syntax Description
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Usage Guidelines
If you do not specify a keyword, only information for trunking ports is displayed.
The interface-number designates the module and port number. Valid values depend on the chassis and module used. For example, if you have a 48-port 10/100BASE-T Ethernet module installed in a 13-slot chassis, valid values for the slot number are from 2 to 13 and valid values for the port number are from 1 to 48.
The module number keyword and argument designate the module number and limits the display to interfaces on the module. Valid values depend on the chassis used. For example, if you have a 13-slot chassis, valid values for the module number are from 2 to 13.
Examples
This example shows how to display the interface-trunk information for module 5:
Router> show interfaces trunk module 5Port Mode Encapsulation Status Native vlanFa5/1 routed negotiate routed 1Fa5/2 routed negotiate routed 1Fa5/3 routed negotiate routed 1Fa5/4 routed negotiate routed 1Fa5/5 routed negotiate routed 1Fa5/6 off negotiate not-trunking 10Fa5/7 off negotiate not-trunking 10Fa5/8 off negotiate not-trunking 1Fa5/9 desirable n-isl trunking 1Fa5/10 desirable negotiate not-trunking 1Fa5/11 routed negotiate routed 1Fa5/12 routed negotiate routed 1...Fa5/48 routed negotiate routed 1Port Vlans allowed on trunkFa5/1 noneFa5/2 noneFa5/3 noneFa5/4 noneFa5/5 noneFa5/6 noneFa5/7 noneFa5/8 200Fa5/9 1-1005Fa5/10 noneFa5/11 noneFa5/12 none...Fa5/48 nonePort Vlans allowed and active in management domainFa5/1 noneFa5/2 noneFa5/3 noneFa5/4 noneFa5/5 noneFa5/6 noneFa5/7 noneFa5/8 200Fa5/9 1-6,10,20,50,100,152,200,300,303-305,349-351,400,500,521,524,570,801-802,850,917,999,1002-1005Fa5/10 noneFa5/11 noneFa5/12 none...Fa5/48 nonePort Vlans in spanning tree forwarding state and not prunedFa5/1 noneFa5/2 noneFa5/3 noneFa5/4 noneFa5/5 noneFa5/6 noneFa5/7 noneFa5/8 200Fa5/9 1-6,10,20,50,100,152,200,300,303-305,349-351,400,500,521,524,570,801-802,850,917,999,1002-1005Fa5/10 noneFa5/11 none...Fa5/48 noneRouter>This example shows how to display the trunking information for active trunking ports:
Router> show interfaces trunkPort Mode Encapsulation Status Native vlanFa5/9 desirable n-isl trunking 1Port Vlans allowed on trunkFa5/9 1-1005Port Vlans allowed and active in management domainFa5/9 1-6,10,20,50,100,152,200,300,303-305,349-351,400,500,521,524,570,801-802,850,917,999,1002-1005Port Vlans in spanning tree forwarding state and not prunedFa5/9 1-6,10,20,50,100,152,200,300,303-305,349-351,400,500,521,524,570,801-802,850,917,999,1002-1005Router>show ip auth-proxy watch-list
To display the authentication proxy watch list information, use the show ip auth-proxy watch-list command.
show ip auth-proxy watch-list
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
12.1(13)E
Support for this command was introduced on the Cisco 7600 series routers.
Examples
This example shows how to display the authentication proxy watch list information:
Router# show ip auth-proxy watch-listAuthentication Proxy Watch-list is enabledWatch-list expiry timeout is 2 minutesTotal number of watch-list entries: 3Source IP Type Violation-count12.0.0.2 MAX_RETRY MAX_LIMIT12.0.0.3 TCP_NO_DATA MAX_LIMIT1.2.3.4 CFGED N/ATotal number of watch-listed users: 3Router#Related Commands
clear ip auth-proxy watch-list
ip auth-proxy max-login-attempts
ip auth-proxy watch-listshow ip cache flow
To display a summary of the NetFlow cache flow entries, use the show ip cache flow command.
show ip cache flow [aggregation type]
Syntax Description
aggregation type
(Optional) Displays the configuration of a particular aggregation cache; see the "Usage Guidelines" section for valid values.
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Usage Guidelines
Valid values for aggregation type are as follows:
•
•
•
•
•
Examples
This example shows how to display a summary of the NetFlow switching statistics:
Router> show ip cache flowIP packet size distribution (0 total packets):1-32 64 96 128 160 192 224 256 288 320 352 384 416 448 480.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000512 544 576 1024 1536 2048 2560 3072 3584 4096 4608.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000IP Flow Switching Cache, 0 bytes0 active, 0 inactive, 0 added0 ager polls, 0 flow alloc failuresExporting flows to 200.0.0.2 (9996)Exporting using source interface Loopback0Version 5 flow records, peer-asActive flows timeout in 10 minutes0 flows exported in 0 udp datagrams, 0 failedlast clearing of statistics neverProtocol Total Flows Packets Bytes Packets Active(Sec) Idle(Sec)-------- Flows /Sec /Flow /Pkt /Sec /Flow /FlowSrcIf SrcIPaddress DstIf DstIPaddress Pr SrcP DstP Pkts B/Pk ActivTable 2-29 describes the fields in the packet size distribution lines of the output.
Table 2-30 describes the fields in the flow switching cache lines of the output.
Table 2-31 describes the fields in the activity-by-protocol lines of the output.
Table 2-32 describes the fields in the current flow lines of the output.
Related Commands
