-
Cisco 7600 Series Router Cisco IOS Command Reference, 12.1E
-
Index
-
Preface
-
Command-Line Interface
-
action to cd
-
Cisco 7600 Series Router Cisco IOS Commands
-
BRC
-
channel-group to clear catalyst6000
-
clear counters to debug callback
-
debug cca to duplex
-
erase to mls aging
-
mls exclude to pagp port-priority
-
policy-map to protocol filtering
-
rcv-queue to show bootflash
-
shutdown vlan to time-range
-
show bootvar to show ip cache
-
show ip cef to show mls asic
-
show mls cef to show qm-sp
-
show queueing to show vtp
-
title
-
udld to username
-
verify to wrr-queue bandwidth
-
wrr-queue cos-map to wrr-queue threshold
-
Acronyms
-
Acknowledgments for Open-Source Software
-
Table Of Contents
clear interface gigabitethernet
clear ip auth-proxy watch-list
clear mac-address-table dynamic
clear mls ip multicast statistics
clear spanning-tree detected-protocol
22clear counters
To clear the interface counters, use the clear counters command.
clear counters [{interface interface-number} | {null interface-number} | {port-channel number} | {vlan vlan-id}]
Syntax Description
Defaults
This command has no default settings.
Command Modes
Privileged EXEC
Command History
Usage Guidelines
This command clears all the current interface counters from the interface unless you specify the interface.
Note
This command does not clear counters retrieved using SNMP, but only those seen when you enter the show queueing interface command.
The interface-number argument designates the module and port number. Valid values for interface-number depend on the specified interface type and the chassis and module used. For example, if you specify a Gigabit Ethernet interface and have a 48-port 10/100BASE-T Ethernet module installed in a 13-slot chassis, valid values for the module number are from 2 to 13 and valid values for the port number are from 1 to 48.
The number of valid values for port-channel number depends on the software release. For releases prior to Release 12.1(3a)E3, valid values are from 1 to 256; for Releases 12.1(3a)E3, 12.1(3a)E4, and 12.1(4)E1, valid values are from 1 to 64. Release 12.1(5c)EX and later support a maximum of 64 values ranging from 1 to 256. Release 12.1(13)E and later support a maximum of 64 values ranging from 1 to 282; values 257 to 282 are supported on the CSM and FWSM only.
If your system is configured with a Supervisor Engine 1, valid values for vlan-id are from 1 to 1005. If your system is configured with a Supervisor Engine 2, valid values for vlan-id are from 1 to 4094. Extended-range VLANs are not supported on systems configured with a Supervisor Engine 1.
Examples
This example shows how to clear all interface counters:
Router# clear countersClear "show interface" counters on all interfaces [confirm]yRouter#This example shows how to clear counters on a specific interface:
Router# clear counters vlan 200Clear "show interface" counters on this interface [confirm]yRouter#Related Commands
show queueing interface (refer to the Cisco IOS Release 12.1 Command Reference)
clear interface gigabitethernet
To clear the hardware logic on a Gigabit Ethernet IEEE 802.3z interface, use the clear interface gigabitethernet command.
clear interface gigabitethernet number
Syntax Description
Defaults
This command has no default settings.
Command Modes
Privileged EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Usage Guidelines
The number argument designates the module and port number. Valid values for number depend on the specified interface type and the chassis and module used. For example, if you specify a Gigabit Ethernet interface and have a 48-port 10/100BASE-T Ethernet module installed in a 13-slot chassis, valid values for the module number are from 2 to 13 and valid values for the port number are from 1 to 48.
Examples
This example shows how to clear the hardware logic on a Gigabit Ethernet IEEE 802.3z interface:
Router# clear interface gigabitethernet 5Router#Related Commands
clear interface vlan
To clear the hardware logic on a VLAN, use the clear interface vlan command.
clear interface vlan vlan-id
Syntax Description
Defaults
This command has no default settings.
Command Modes
Privileged EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
12.1(11b)EX
This command was changed to support extended-range VLANs.
Usage Guidelines
If your system is configured with a Supervisor Engine 1, valid values for vlan-id are from 1 to 1005. If your system is configured with a Supervisor Engine 2, valid values for vlan-id are from 1 to 4094. Extended-range VLANs are not supported on systems configured with a Supervisor Engine 1.
Examples
This example shows how to clear the hardware logic on a specific VLAN:
Router# clear interface vlan 5Router#Related Commands
clear ip access-template
To clear statistical information on the access list, use the clear ip access-template command.
clear ip access-template access-list
Syntax Description
access-list
Access list number; valid values are from 100 to 199 for an IP extended-access list and from 2000 to 2699 for an expanded-range IP extended-access list.
Defaults
This command has no default settings.
Command Modes
Privileged EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Examples
This example shows how to clear statistical information on the access list:
Router# clear ip access-template 201Router#Related Commands
clear ip auth-proxy watch-list
To delete a single watch-list entry or all watch-list entries, use the clear ip auth-proxy watch-list command.
clear ip auth-proxy watch-list {ip-addr | *}
Syntax Description
ip-addr
Specifies the IP address to be deleted from the watch list.
*
Removes all watch-list entries from the watch list.
Defaults
This command has no default settings.
Command Modes
Privilieged EXEC
Command History
12.1(13)E
Support for this command was introduced on the Cisco 7600 series routers.
Usage Guidelines
If there are entries in the watch list that you suspect are not valid, you can enter the clear ip auth-proxy watch-list command to clear them manually instead of waiting for the watch list expiry-time to expire.
Examples
This example shows how to delete a single watch-list entry:
Router# clear ip auth-proxy watch-list 12.0.0.2Router#This example shows how to delete all watch-list entries:
Router# clear ip auth-proxy watch-list *Router#Related Commands
ip auth-proxy max-login-attempts
ip auth-proxy watch-list
show ip auth-proxy watch-listclear ip cef epoch full
To begin a new epoch and increment the epoch number for all tables (including the adjacency table), use the clear ip cef epoch full command.
clear ip cef epoch full
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Privileged EXEC
Command History
12.1(8a)EX
Support for this command was introduced on the Cisco 7600 series routers.
Usage Guidelines
Use the clear ip cef epoch full command when you want to rebuild a table. This command allows old and new table entries to be distinguished within the same data structure and allows you to retain the old CEF database table while constructing the new table.
These show commands display epoch information:
•
•
•
•
Examples
This example shows the output before and after you clear the epoch table and increment the epoch number:
Router# show ip cef epochCEF epoch information:Table:Default-tableTable epoch:2 (164 entries at this epoch)Adjacency tableTable epoch:1 (33 entries at this epoch)Router# clear ip cef epoch fullRouter# show ip cef epochCEF epoch information:Table:Default-tableTable epoch:3 (164 entries at this epoch)Adjacency tableTable epoch:2 (33 entries at this epoch)Router#Related Commands
show adjacency detail (refer to the Cisco IOS Release 12.1 Command Reference)
show adjacency summary (refer to the Cisco IOS Release 12.1 Command Reference)
show ip cef detail (refer to the Cisco IOS Release 12.1 Command Reference)
show ip cef epoch
show ip cef summary (refer to the Cisco IOS Release 12.1 Command Reference)clear ip cef inconsistency
To clear the CEF inconsistency checker statistics and records, use the clear ip cef inconsistency command.
clear ip cef inconsistency
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Privileged EXEC
Command History
12.1(8a)EX
Support for this command was introduced on the Cisco 7600 series routers.
Usage Guidelines
This command clears the CEF inconsistency checker statistics and records that accumulate when the ip cef table consistency-check command is enabled.
Examples
This example shows how to clear all CEF inconsistency checker statistics and records:
Router# clear ip cef inconsistencyRouter#Related Commands
ip cef table consistency-check
show ip cef inconsistencyclear ip flow stats
To clear the NetFlow switching statistics, use the clear ip flow stats command.
clear ip flow stats
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Privileged EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Usage Guidelines
The show ip cache flow command displays the NetFlow switching statistics.
Examples
This example shows how to clear the NetFlow switching statistics:
Router# clear ip flow statsRouter#Related Commands
clear ip igmp group
To delete IGMP group cache entries, use the clear ip igmp group command.
clear ip igmp group [{interface interface-number} | {host-name | group-address} {loopback interface-number} | {null interface-number} | {port-channel number} | {vlan vlan-id}]
Syntax Description
Defaults
This command has no default settings.
Command Modes
Privileged EXEC
Command History
Usage Guidelines
The number of valid values for port-channel number depends on the software release. For releases prior to Release 12.1(3a)E3, valid values are from 1 to 256; for Releases 12.1(3a)E3, 12.1(3a)E4, and 12.1(4)E1, valid values are from 1 to 64. Release 12.1(5c)EX and later support a maximum of 64 values ranging from 1 to 256. Release 12.1(13)E and later support a maximum of 64 values ranging from 1 to 282; values 257 to 282 are supported on the CSM and FWSM only.
The interface-number argument designates the module and port number. Valid values for interface-number depend on the specified interface type and the chassis and module used. For example, if you specify a Gigabit Ethernet interface and have a 48-port 10/100BASE-T Ethernet module installed in a 13-slot chassis, valid values for the module number are from 2 to 13 and valid values for the port number are from 1 to 48.
If your system is configured with a Supervisor Engine 1, valid values for vlan-id are from 1 to 1005. If your system is configured with a Supervisor Engine 2, valid values for vlan-id are from 1 to 4094. Extended-range VLANs are not supported on systems configured with a Supervisor Engine 1.
The IGMP cache contains a list of hosts on the directly connected LAN.
To delete all entries from the IGMP cache, specify the clear ip igmp group command with no arguments.
Examples
This example shows how to clear entries for a specific group from the IGMP cache:
Router# clear ip igmp group 224.0.255.1Router#This example shows how to clear IGMP group cache entries from a specific interface:
Router# clear ip igmp group gigabitethernet 2/2Router#Related Commands
ip host (refer to the Cisco IOS Release 12.1 Command Reference)
show ip igmp groups (refer to the Cisco IOS Release 12.1 Command Reference)
show ip igmp interfaceclear lacp counters
To clear the statistics for all interfaces belonging to a specific channel group, use the clear lacp counters command.
clear lacp [channel-group] counters
Syntax Description
Defaults
This command has no default settings.
Command Modes
Privileged EXEC
Command History
Usage Guidelines
This command is not supported on systems configured with a Supervisor Engine 1.
If you do not specify a channel-group, all channel groups are cleared.
If you enter this command for a channel group that contains members in PAgP mode, the command is ignored.
Examples
This example shows how to clear the statistics for a specific group:
Router# clear lacp 1 countersRouter#Related Commands
clear mac-address-table dynamic
To clear dynamic address entries from the Layer 2 MAC address table, use the clear mac-address-table dynamic command.
clear mac-address-table dynamic [{address mac-addr} | {interface interface interface-number} | {protocol {assigned | ip | ipx | other}}] [vlan vlan-id]
Syntax Description
Defaults
This command has no default settings.
Command Modes
Privileged EXEC
Command History
Usage Guidelines
The protocol {assigned | ip | ipx | other} keywords are supported on systems configured with a Supervisor Engine 1 but not on systems configured with a Supervisor Engine 2.
Enter the clear mac-address-table dynamic command with no arguments to remove all dynamic entries from the table.
The interface-number argument designates the module and port number. Valid values for interface-number depend on the specified interface type and the chassis and module used. For example, if you specify a Gigabit Ethernet interface and have a 48-port 10/100BASE-T Ethernet module installed in a 13-slot chassis, valid values for the module number are from 2 to 13 and valid values for the port number are from 1 to 48.
If your system is configured with a Supervisor Engine 1, valid values for vlan-id are from 1 to 1005. If your system is configured with a Supervisor Engine 2, valid values for vlan-id are from 1 to 4094. Extended-range VLANs are not supported on systems configured with a Supervisor Engine 1.
Examples
This example shows how to clear all dynamic Layer 2 entries for a specific interface (e2/1) and protocol type (IPX):
Router# clear mac-address-table dynamic interface e2/1 protocol ipxRouter#Related Commands
mac-address-table aging-time
mac-address-table static
show mac-address-tableclear mls
To clear IP and IPX shortcut entries, use the clear mls command.
clear mls ip [[module mod] [destination ip-addr-spec] [source ip-addr-spec] [flow {tcp | udp} {src-port | any} {dst-port | any}] [macs mac-addr] [macd mac-addr] [interface interface-num]] | [all]
clear mls ipx [[module mod] [destination ipx-network [ipx-node]] [source ipx-network] [macs mac-addr] [macd mac-addr] [interface interface-num] | [all]
Syntax Description
Defaults
This command has no default settings.
Command Modes
Privileged EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Usage Guidelines
The module mod option is supported only on systems configured with a Supervisor Engine 2.
Entering any combination of input parameters narrows down the search of entries to be cleared. A 0 value for src-port and dst-port clears all entries. Unspecified options are treated as wildcards, and all entries are cleared. The src-port and dst-port values should be specified as one of the following: telnet, FTP, WWW, SMTP, X, or DNS.
When entering the IPX address syntax, use the following format:
•
•
•
Up to 16 routers can be included explicitly as MLS-RPs.
To use a router as an MLS, you must meet these conditions:
•
•
•
Use the following syntax to specify an IP subnet address:
•
•
•
If you do not use the all keyword, you must specify at least one of the other four keywords (source, destination, flow, or interface) and its arguments.
Examples
This example shows how to clear all entries associated with a specific interface (e2/2) that have a specific destination IP address (173.11.50.89):
Router# clear mls ip destination 173.11.50.89 interface e2/2Router#Related Commands
clear mls exclude protocol
To remove an MLSE entry, use the clear mls exclude protocol command.
clear mls exclude protocol {tcp | udp | all} [port port-number]
Syntax Description
tcp
TCP port.
udp
UDP port.
all
Port that is applied to both TCP and UDP traffic.
port port-number
(Optional) Port number.
Defaults
This command has no default settings.
Command Modes
Privileged EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Examples
This example shows how to set TCP packets in a protocol port to be switched through hardware connections:
Router# clear mls exclude protocol tcp 25Router#Related Commands
clear mls ip multicast statistics
To reset the IP multicast statistics counters, use the clear mls ip multicast statistics command.
clear mls ip multicast statistics
Syntax Description
This command has no keywords or arguments.
Defaults
This command has no default settings.
Command Modes
Privileged EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Examples
This example shows how to reset the IP multicast statistics counters:
Router# clear mls ip multicast statisticsRouter#Related Commands
clear mls nde counters
To clear NDE counters, use the clear mls nde counters command.
clear mls nde counters
Syntax Description
This command has no keywords or arguments.
Defaults
This command has no default settings.
Command Modes
Privileged EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Examples
This example shows how to reset the NDE statistics counters:
Router# clear mls nde countersRouter#Related Commands
clear mls nde flow
To clear the NDE filter, use the clear mls nde flow command.
clear mls nde flow {exclude | include | all}
Syntax Description
exclude
Clears the exclusion filter.
include
Clears the inclusion filter.
all
Clears both the exclusion and inclusion filters.
Defaults
This command has no default settings.
Command Modes
Privileged EXEC
Command History
12.1(13)E
Support for this command was introduced on the Cisco 7600 series routers.
Usage Guidelines
If you clear both the exclusion and inclusion filters, all flows are exported.
Examples
This example shows how to clear the NDE exclude filter:
Router# clear mls nde flow excludeRouter#This example shows how to clear the NDE include filter:
Router# clear mls nde flow includeRouter#This example shows how to clear both NDE filters:
Router# clear mls nde flow allRouter#Related Commands
clear mls qos
To clear both statistics and token counts in high-rate and low-rate policer buckets, use the clear mls qos command.
clear mls qos [{ip | ipx | mac} [{interface interface-number} | {null interface-number} | {port-channel number} | {vlan vlan-id}]]
Syntax Description
Defaults
This command has no default settings.
Command Modes
Privileged EXEC
Command History
Usage Guidelines
Note
The number of valid values for port-channel number depends on the software release. For releases prior to Release 12.1(3a)E3, valid values are from 1 to 256; for Releases 12.1(3a)E3, 12.1(3a)E4, and 12.1(4)E1, valid values are from 1 to 64. Release 12.1(5c)EX and later support a maximum of 64 values ranging from 1 to 256. Release 12.1(13)E and later support a maximum of 64 values ranging from 1 to 282; values 257 to 282 are supported on the CSM and FWSM only.
The interface-number argument designates the module and port number. Valid values for interface-number depend on the specified interface type and the chassis and module used. For example, if you specify a Gigabit Ethernet interface and have a 48-port 10/100BASE-T Ethernet module installed in a 13-slot chassis, valid values for the module number are from 2 to 13 and valid values for the port number are from 1 to 48.
If your system is configured with a Supervisor Engine 1, valid values for vlan-id are from 1 to 1005. If your system is configured with a Supervisor Engine 2, valid values for vlan-id are from 1 to 4094. Extended-range VLANs are not supported on systems configured with a Supervisor Engine 1.
If you enter the clear mls qos command with no arguments, global and per-interface aggregate QoS counters for all protocols are cleared.
If you do not enter an interface type, protocol aggregate QoS counters for all interfaces are cleared.
Examples
This example shows how to clear global and per-interface aggregate QoS counters for all protocols:
Router# clear mls qosRouter#This example shows how to clear specific protocol aggregate QoS counters for all interfaces:
Router# clear mls qos ipRouter#Related Commands
clear pagp
To clear port-channel information, use the clear pagp command.
clear pagp {group-number | counters}
Syntax Description
group-number
Channel group number; see the "Usage Guidelines" section for valid values.
counters
Clears traffic filters.
Defaults
This command has no default settings.
Command Modes
Privileged EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Usage Guidelines
The number of valid values for group-number depends on the software release. For releases prior to Release 12.1(3a)E3, valid values are from 1 to 256; for Releases 12.1(3a)E3, 12.1(3a)E4, and 12.1(4)E1, valid values are from 1 to 64. Release 12.1(5c)EX and later support a maximum of 64 values ranging from 1 to 256. Release 12.1(13)E and later support a maximum of 64 values ranging from 1 to 282; values 257 to 282 are supported on the CSM and FWSM only.
Examples
This example shows how to clear port-channel information for a specific group:
Router# clear pagp 324Router#This example shows how to clear port-channel traffic filters:
Router# clear pagp countersRouter#Related Commands
clear spanning-tree detected-protocol
To restart protocol migration, use the clear spanning-tree detected-protocol command.
clear spanning-tree detected-protocol [interface interface interface-number]
Syntax Description
Defaults
This command has no default settings.
Command Modes
EXEC mode
Command History
Usage Guidelines
RSTP and MST have built-in compatibility mechanisms that allow them to interact properly with other versions of IEEE spanning tree or other regions. For example, a bridge running RSTP can send 802.1D BPDUs on one of its ports when it is connected to a legacy bridge. An MST bridge can detect that a port is at the boundary of a region when it receives a legacy BPDU or an MST BPDU associated with a different region. These mechanisms are not always able to revert to the most efficient mode. For example, an RSTP bridge designated for a legacy 802.1D stays in 802.1D mode even after the legacy bridge has been removed from the link. Similarly, an MST port assumes that it is a boundary port when the bridges to which it is connected have joined the same region. To force the MST port to renegotiate with the neighbors, enter the clear spanning-tree detected-protocol command.
The valid values for interface-number depend on the specified interface type and the chassis and module used. For example, if you specify a Gigabit Ethernet interface and have a 48-port 10/100BASE-T Ethernet module installed in a 13-slot chassis, valid values for the module number are from 2 to 13 and valid values for the port number are 1 to 48.
The number of valid values for port-channel number depends on the software release. For releases prior to Release 12.1(3a)E3, valid values are from 1 to 256; for Releases 12.1(3a)E3, 12.1(3a)E4, and 12.1(4)E1, valid values are from 1 to 64. Release 12.1(5c)EX and later support a maximum of 64 values ranging from 1 to 256. Release 12.1(13)E and later support a maximum of 64 values ranging from 1 to 282; values 257 to 282 are supported on the CSM and FWSM only.
If your system is configured with a Supervisor Engine 1, valid values for vlan are from 1 to 1005. If your system is configured with a Supervisor Engine 2, valid values for vlan are from 1 to 4094. Extended-range VLANs are not supported on systems configured with a Supervisor Engine 1.
If you specify an interface, the command is applied to this interface only. If you enter the clear spanning-tree detected-protocol command with no arguments, the command is applied to every port of the Cisco 7600 series router.
Examples
The example shows how to restart protocol migration on a specific interface:
Router# clear spanning-tree detected-protocol fa1/1Router#Related Commands
clear vlan counters
To clear the software-cached counter values to start from zero again for a specified VLAN or all existing VLANs, use the clear vlan counters command.
clear vlan [vlan-id] counters
Syntax Description
Defaults
This command has no default settings.
Command Modes
Privileged EXEC
Command History
Usage Guidelines
If you do not specify a vlan-id; the software-cached counter values for all existing VLANs are cleared.
If your system is configured with a Supervisor Engine 1, valid values for vlan-id are from 1 to 1005. If your system is configured with a Supervisor Engine 2, valid values for vlan-id are from 1 to 4094. Extended-range VLANs are not supported on systems configured with a Supervisor Engine 1.
Examples
Router# clear vlan 10 countersClear "show vlan" counters on this vlan [confirm]yRouter#Related Commands
copy /noverify
To disable the automatic image verification for the current copy operation, use the copy /noverify command.
copy /noverify source-url destination-url
Syntax Description
Defaults
Verification is done automatically after completion of a copy operation.
Command Modes
EXEC
Command History
12.1(19)E
Support for this command was introduced on the Cisco 7600 series routers.
Usage Guidelines
The exact format of the source and destination URLs varies according to the file or directory location. You may enter either an alias keyword for a particular file or an alias keyword for a file system type (not a file within a type).
Timesaver
Table 2-2 shows two keyword shortcuts to URLs.
Table 2-3 through Table 2-5 list aliases by file system type. If you do not specify an alias, the system looks for a file in the current directory.
Table 2-3 lists the URL prefix aliases for special (opaque) file systems, Table 2-4 lists the URL prefix aliases for network file systems, and Table 2-5 lists the URL prefix aliases for local writable storage file systems.
You can enter on the command line all necessary source- and destination-URL information and the username and password to use, or you can enter the copy command and have the switch prompt you for any missing information.
If you enter information, choose one of the following three options: running-config, startup-config, or a file system alias (see previous tables). The location of a file system dictates the format of the source or destination URL.
The colon is required after the alias. However, earlier commands not requiring a colon remain supported, but are unavailable in context-sensitive help.
The entire copying process may take several minutes and differs from protocol to protocol and from network to network.
In the alias syntax for ftp:, rcp:, and tftp:, the location is either an IP address or a host name. The filename is specified for the directory that is used for file transfers.
Enter the file verify auto command to set up verification globally.
Examples
This example shows how to disable the automatic image verification for the current copy operation:
Router# copy /noverify tftp: sup-bootflash:.................................................[OK - 24301348 bytes]24301348 bytes copied in 157.328 secs (154463 bytes/sec)Router#Related Commands
debug adjacency
To display information on the adjacency database, use the debug adjacency command. Use the no form of this command to disable debugging output.
debug adjacency [ipc]
no debug adjacency
Syntax Description
Defaults
This command has no default settings.
Command Modes
Privileged EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Examples
This example shows how to display information on the adjacency database:
Router# debug adjacency4d02h: ADJ: add 172.20.52.36 (GigabitEthernet1/1) via ARP will expire: 04:00:004d02h: ADJ: add 172.20.52.36 (GigabitEthernet1/1) via ARP will expire: 04:00:004d02h: ADJ: add 172.20.52.36 (GigabitEthernet1/1) via ARP will expire: 04:00:004d02h: ADJ: add 172.20.52.36 (GigabitEthernet1/1) via ARP will expire: 04:00:004d02h: ADJ: add 172.20.52.36 (GigabitEthernet1/1) via ARP will expire: 04:00:004d02h: ADJ: add 172.20.52.36 (GigabitEthernet1/1) via ARP will expire: 04:00:004d02h: ADJ: add 172.20.52.36 (GigabitEthernet1/1) via ARP will expire: 04:00:004d02h: ADJ: add 172.20.52.36 (GigabitEthernet1/1) via ARP will expire: 04:00:00<... output truncated ...>Router#Related Commands
undebug adjacency (same as no debug adjacency)
debug backup
To debug backup events, use the debug backup command. Use the no form of this command to disable debugging output.
debug backup
no debug backup
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Privileged EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Examples
This example shows how to debug backup events:
Router# debug backupBackup events debugging is onRouter#Related Commands
undebug backup (same as no debug backup)
debug callback
To debug PPP telephone callback activity, use the debug callback command. Use the no form of this command to disable debugging output.
debug callback
no debug callback
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Privileged EXEC
Command History
12.1(8a)E3
Support for this command was introduced on the Cisco 7600 series routers.
Examples
This example shows how to debug callback activity:
Router# debug callbackCallback activity debugging is onRouter#Related Commands
undebug callback (same as no debug callback)
