-
Cisco 7600 Series Ethernet Services 40G Line Card Hardware Installation Guide
-
Preface
-
Cisco 7600 Series Ethernet Services 40G Line Card Product Overview
-
Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
-
Preparing to Install a Cisco 7600 Series Ethernet Services 40G Line Card
-
Installing and Removing a Cisco 7600 Series Ethernet Services 40G Line Card
-
Installing and Removing SFP and XFP Modules
-
Troubleshooting the Installation
-
Table Of Contents
Cisco 7600 Ethernet Services Plus Line Card Product Overview
Introduction to the Cisco 7600 Ethernet Services Plus Line Card
Cisco 7600 Series Ethernet Services Plus Line Card Product Numbers
Cisco IOS Software Release and Hardware Revision Requirements
Cisco 7600 Ethernet Services Plus Line Card Product Overview
This chapter provides an introduction to the Cisco 7600 Series ES+ line cards. It includes the following sections:
•
Introduction to the Cisco 7600 Ethernet Services Plus Line Card
•
Introduction to the Cisco 7600 Ethernet Services Plus Line Card
The Cisco 7600 Series ES+ line cards are a multiple-fabric, fixed-port Ethernet line card for the Cisco 7600 series routers that are capable of 40 Gbps full-duplextraffic forwarding using a fixed port interface design. The Cisco 7600 Series ES+ line card versions are:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
The difference between the versions are the link interface daughter cards that accept small form-factor pluggable (SFP or XFP1 ) optical transceivers. Additionally, each of the versions has a common baseboard card and a control processor daughter card.
The SFP and XFP modules allow the line cards to be configured for different media types (copper or fiber) and different optical requirements (single mode fiber or multimode fiber) as available.
See Table 1-4 for information about which SFPs or XFPs are accepted on the different Cisco 7600 Series ES+ line cards.
Product Overview
The Cisco 7600 Series ES+ line cards have the following features:
The system features listed here specify some of the key performance metrics and capabilities of the line cards. The information below applies to all four line cards unless stated otherwise.
•
•
•
•
•
•
•
Cisco 7600 Series Ethernet Services Plus Line Card Product Numbers
Table 1-1 lists the Cisco product numbers for the line cards.
Note
Supported Platforms
Table 1-2 lists the supported router platforms for Cisco 7600 ES+ line cards:
Cisco IOS Software Release and Hardware Revision Requirements
The Cisco 7600 ES+ line cards have certain Cisco IOS software requirements. Also, to ensure compatibility with the software, your Cisco 7600 ES+ line card should have a specific hardware revision number. The number is printed on a label affixed to the component side of the card and is displayed by the show diag command.
Table 1-3 lists the hardware and software requirements for Cisco 7600 ES+ line cards.
The show diag slot_number, show version, and show hardware commands display the current hardware configuration of the router, including the system software version that is currently loaded and running, and the hardware revision number. For complete descriptions of show commands, refer to the Cisco IOS Configuration Fundamentals Configuration Guide and the Cisco IOS Configuration Fundamentals Command Reference for the installed Cisco IOS release.
If the command displays indicate that the Cisco IOS software is a version earlier than you need, check the contents of flash memory to determine if the required images are available on your system. The dir devicename command displays a list of all files stored in flash memory. If you do not have the correct software version, contact Cisco customer service.
For software configuration information, refer to the Cisco IOS software configuration and command reference publications for the installed Cisco IOS release. Also refer to the Cisco IOS software release notes for additional information.
Modular Optics Compatibility
The Cisco 7600 Series ES+ line cards use small form-factor pluggable (SFP or XFP) optical transceivers to provide network connectivity. Table 1-4 provides links to tables showing the supported modules for the different Cisco 7600 Series ES+ line cards.
Table 1-4 Supported Optical Transceiver Modules
7600-ES+20G3C
Cisco 7600 ES+ 20G3C, -20G3CXL Supported SFP Modules; see Table 2-16 on page 2-15.
7600-ES+20G3CXL
7600-ES+2TG3C
Cisco 7600 ES+ 2TG3C, -3CXL Supported XFP Modules; see Table 2-5 on page 2-7.
7600-ES+2TG3CXL
7600-ES+40G3C
Cisco 7600 ES+ 40G3C, -40G3CXL Supported SFP Modules; see Table 2-21 on page 2-20.
7600-ES+40G3CXL
7600-ES+4TG3C
Cisco 7600 ES+ 4TG3C, -4TG3CXL Supported XFP Modules; see Table 2-10 on page 2-11.
7600-ES+4TG3CXL
76-ES+XT-2TG3CXL
Supported XFP Modules; see Table 2-26 on page 2-25.
76-ES+XT-4TG3CXL
Supported XFP Modules; see Table 2-31 on page 2-29.
76-ES+T-20G
Supported SFP Modules; see TBD
76-ES+T-2TG
Supported XFP Modules; see TBD
76-ES+T-40G
Supported SFP Modules; see TBD
76-ES+T-4TG
Supported XFP Modules; see TBD
Power Management
The Cisco ES+ line cards consume chassis power; you must make sure the chassis is within the power budget on Cisco 7600 series routers. See Table 1-5.
Table 1-5 Cisco 7600 ES+ Line Card Power Consumption
If the power limit is exceeded, the Cisco ES+ line card is not powered up and an error message is displayed.
Router#%C7KPWR-SP-4-POWERDENIED:insufficient power, module in slot 3 power denied.On a Cisco 7600 series router, use the show power command on the Route Processor to determine how much power you have available in the chassis and how much is being used or reserved by line cards, supervisor engines, and fan trays.
The following example shows the sample output for the show power command on a Cisco 7600 series router:
Router# show powersystem power redundancy mode = redundantsystem power redundancy operationally = non-redundantsystem power total = 3795.12 Watts (90.36 Amps @ 42V)system power used = 3320.94 Watts (79.07 Amps @ 42V)system power available = 474.18 Watts (11.29 Amps @ 42V)Power-Capacity PS-Fan Output OperPS Type Watts A @42V Status Status State---- ------------------ ------- ------ ------ ------ -----1 WS-CAC-4000W-INT 3795.12 90.36 OK OK on2 nonePwr-Allocated OperFan Type Watts A @42V State---- ------------------ ------- ------ -----1 WS-C6K-13SLT-FAN2 298.20 7.10 OKPwr-Requested Pwr-Allocated Admin OperSlot Card-Type Watts A @42V Watts A @42V State State---- ------------------ ------- ------ ------- ------ ----- -----2 7600-SIP-200 240.24 5.72 240.24 5.72 on on3 WS-X6724-SFP 125.16 2.98 125.16 2.98 on on4 7600-SIP-400 265.02 6.31 265.02 6.31 on on7 RSP720-3CXL-GE 354.06 8.43 354.06 8.43 on on8 RSP720-3C-GE 354.06 8.43 354.06 8.43 on on9 7600-ESM-BASE 304.92 7.26 304.92 7.26 on on10 7600-ES+20G3CXL 297.36 7.08 297.36 7.08 on on11 7600-SIP-600 341.88 8.14 341.88 8.14 on on12 7600-SIP-600 341.88 8.14 341.88 8.14 on on13 WS-X6704-10GE 398.16 9.48 398.16 9.48 on onRouter#1 SFP modules are optics modules with speeds lower than 10 Gbps; XFP modules are optics modules with speeds equal to or greater than 10 Gbps.
