Table Of Contents
Guide to Supported Hardware for Cisco 7600 Series Routers with Cisco IOS Release 12.2SR
Contents
Document Revision History
Supported Hardware
Supervisor Engines
Supervisor Engine 720
Supervisor Engine 32
Route Switching Processor 720
Policy Feature Cards
Policy Feature Card Guidelines and Restrictions
Policy Feature Card 3BXL
Policy Feature Card 3B
Policy Feature Card 3C
Policy Feature Card 3CXL
Distributed and Centralized Forwarding Cards
Centralized Forwarding Card (WS-X6700-CFC)
Distributed Forwarding Card 3BXL
Distributed Forwarding Card 3B
Distributed Forwarding Card 3CXL
Distributed Forwarding Card 3C
10-Gigabit Ethernet Switching Modules
XENPAKs
X2 Modules
Gigabit Ethernet Switching Modules
Small Form-Factor Pluggable Modules (SFPs)
Gigabit Ethernet SFPs
Fast Ethernet SFPs
10-Gigabit Ethernet Transceiver Modules
DWDM-XFP Modules
Gigabit Interface Converters (GBICs)
Power over Ethernet Daughtercards
10/100/1000 Ethernet Switching Modules
Fast Ethernet Switching Modules
Ethernet/Fast Ethernet (10/100) Switching Modules
Ethernet Switching Modules
Optical Services Modules (OSMs)
OSM Guidelines and Restrictions
Gigabit Ethernet WAN
OC-48 Packet over SONET
OC-48 DPT/Packet over SONET
OC-12 Packet over SONET
OC-3 Packet over SONET
OC-12 Channelized
CT3/T1 Channelized/Unchannelized
OC-12 ATM
SPA Interface Processors (SIPs)
SIP-400 Combinations
Shared Port Adapters (SPAs)
Ethernet SPAs
Fast Ethernet SPAs
POS SPAs
ATM SPAs
Serial SPAs
Circuit Emulation over Packet (CEoP) SPAs
Services SPA Carrier (SSC)
Services SPAs
Enhanced FlexWAN Module
Enhanced FlexWAN Module Port Adapters
Ethernet Services 20G Line Cards
Ethernet Services 40G Line Cards
ES+ Transport line cards start here
ES+ Transport line cards end here
NEW EAGLE ES+ line cards start here
NEW EAGLE ES+ line cards end here
Service Modules
Anomaly Guard Module
Traffic Anomaly Detector Module
Persistent Storage Device (PSD) Module
Multi-Processor WAN Application Module (MWAM)
Content Services Gateway (CSG) Module
Firewall Services Module
Intrusion Detection System Modules (IDSMs)
Network Analysis Modules (NAMs)
Application Control Engine (ACE) Module
Service Application Module for IP
Wireless Services Module (WiSM)
Fan Trays
High-Capacity Fan Trays
Power Supplies
CISCO7606 Power Supplies
CISCO7606-S Power Supplies
WS-C6504-E and CISCO7604 Power Supplies
WS-C6503, WS-C6503-E, and CISCO7603 Power Supplies
CISCO7603-S Power Supplies
All Other Power Supplies
Chassis
13-Slot Chassis
9-Slot Chassis
6-Slot Chassis
4-Slot Chassis
3-Slot Chassis
Unsupported Hardware
Unsupported Service Modules
Unsupported Port Adapters
Unsupported Supervisor Engines
Unsupported Policy Feature Cards and Distributed Forwarding Cards
Unsupported Line Cards
Unsupported Service Modules
Unsupported Chassis
Unsupported Power Supplies
Related Documentation
Obtaining Documentation, Obtaining Support, and Security Guidelines
Guide to Supported Hardware for Cisco 7600 Series Routers with Cisco IOS Release 12.2SR
This publication lists the supported hardware for Cisco 7600 series routers with Cisco IOS Release 12.2SR.
Use this publication with the Cross-Platform Release Notes for Cisco IOS Release 12.2SR.
Contents
This publication contains these sections:
•
Document Revision History
•Supported Hardware
•Unsupported Hardware
•Related Documentation
•Obtaining Documentation, Obtaining Support, and Security Guidelines
Document Revision History
Revision
|
Date
|
Change Summary
|
OL-10362-11
|
November, 2009
|
Added the following for Cisco IOS release 12.2(33)SRE:
•Added support for the following ES+ Combo cards:
–76-ES+XC-40G3CXL
–76-ES+XC-40G3C
–76-ES+XC-20G3CXL
–76-ES+XC-20G3C
–SFP-GE-T/S/L/Z support on X6724/X6748
–DWDM-X2-xx.xx and X2-10GB-LRM, X2 10GB-ZR support on 7600 cards (RSP720-10GE and WS-X6708-10GE)
–DWDM-X2-xx.xx and X2-10GB-LRM, X2 10GB-ZR support on 7600 cards (RSP720-10GE and WS-X6708-10GE)
–Enable support for additional DWDM SFPs (DWDM-SFP-3346, DWDM-SFP-3739, DWDM-SFP-4134, DWDM-SFP-4532, DWDM-SFP-4931, DWDM-SFP-5332, DWDM-SFP-5736, DWDM-SFP-6141) in ES+ and ES+Combo
–Enabled support for additional DWDM SFPs (DWDM-SFP-3346, DWDM-SFP-3739, DWDM-SFP-4134, DWDM-SFP-4532, DWDM-SFP-4931, DWDM-SFP-5332, DWDM-SFP-5736, DWDM-SFP-6141) in ES20/SIP400/SIP600 (HW)
–PWR-4500-DC Power Supply
•Support for ES+ transport card is extended to12.2(33) SRE.
|
OL-10362-10
|
May, 2009
|
Added the following for Cisco IOS release 12.2(33)SRD3:
•Added support for the following ES+ transport cards:
–76-ES+T-20G
–76-ES+T-40G
–76-ES+T-2TG
–76-ES+T-4TG
|
OL-10362-9
|
May, 2009
|
Added the following for Cisco IOS release 12.2(33)SRD2:
•Added support for SFP-GE-T, SFP-GE-S, SFP-GE-L, and SFP-GE-Z to WS-X6724-SFP and WS-X6748-SFP line cards.
•Added support for ONS-SC-155-EL to the SPA-1ChOC3-CE-ATM on the SIP-400 and to the SPA-1XCHSTM1/OC3 on the SIP-400.
|
OL-10362-8
|
February, 2009
|
Added the following for Cisco IOS release 12.2(33)SRD1:
•76-ES+XT-2TG3CXL
•76-ES+XT-4TG3CXL
|
OL-10362-7
|
October, 2008
|
Added the following for Cisco IOS release 12.2(33)SRD:
•7600-ES+2TGCXL
•7600-ES+2TG3C
•7600-ES+4TGCXL
•7600-ES+4TG3C
•7600-ES+40G3C
•7600-ES+20G3CXL
•7600-ES+20G3C
•7600-ES+40G3CXL
•CWDM SFP Support
•DWDM SFP Support
•XFP-10GER-OC192IR= Version 2 XFP support
•SFP-GE-T= with ES40 Line Card Support
•XFP-10GZR-OC192LR+= XFP Support
•support BX optics (GLC-BX-U=, GLC-BX-D=) with GE SPA (SIP line cards), ES20 & ES40 line cards
•DWDM XFP support
•SPA-8X1FE-TX-V2 and SPA-4X1FE-TX-V2 Support on SIP-400
•Network Analysis Modules (NAMs) Support for RSP720-10GE
|
OL-10362-6
|
May, 2008
|
Added the following for Cisco IOS release 12.2(33)SRC1:
•SPA-4XT-Serial SPA support on SIP-200
•Additional DWDM XFP support for ES20 line card, SIP-400, and SIP-600
|
OL-10362-5
|
April, 2008
|
Added the following for Cisco IOS release 12.2(33)SRB3:
•DWDM XFP support on Cisco 7600 ES20 line card and SIP-600
•SFP-GE-T support on Cisco 7600 ES20 line card, SIP-400, and SIP-600
•CWDM SFP support on Cisco 7600 ES20 line card
|
OL-10362-4
|
January, 2008
|
Added the following for Cisco IOS release 12.2(33)SRC:
•SPA-2CHT3-CE-ATM on SIP-400
•WS-X6708-10G-3C, WS-X6708-10G-3CXL
•RSP720-3C-10GE, RSP720-3CXL-10GE
•SPA-1X10GE-L-V2 on the SIP-400
•SPA-1xCHSTM1/OC3 on the SIP-400
•SFP-GE-T Support on the SIP-400, SIP-600, and Ethernet Services 20G line cards
•SPA-2XCT3/DS0, SPA-4XCT3/DS0 support on SIP-400
•SPA-8XCHT1/E1 on the SIP-400
•SPA-2XT3/E3, SPA-4XT3/E3 support on SIP-400
•Wireless Services Module (WiSM)
|
OL-10362-3
|
June, 2007
|
Added the following for Cisco IOS release 12.2(33)SRB1:
•Cisco 7606-S router chassis
•Cisco 7603-S router chassis
•1500 W DC input (PWR-1500-DC) power supply
•XFP-10GZR-OC192LR Gigabit Ethernet Transceiver Module
•Cisco 7600 Series ACE 20 HW for Session Border Controller
|
OL-10362-2
|
February, 2007
|
Added the following for Cisco IOS release 12.2SRB:
•RSP 720
•Policy Feature Card 3C
•Policy Feature Card 3CXL
•Distributed Forwarding Card 3CXL
•SFP-GE-S, SFP-GE-L, SFP-GE-Z
•1-Port and 24-Port Channelized CEoP SPAs
•Ethernet Services 20G line cards
•Application Control Engine (ACE) Module
•Service Application Module for IP
•6000 W DC power supply
•Cisco 7609-S router chassis
|
OL-10362-1
|
May, 2006
|
Initial version
|
Supported Hardware
These sections describe the hardware supported in Cisco IOS Release 12.2SR:
•Supervisor Engines
•Policy Feature Cards
•Distributed and Centralized Forwarding Cards
•XENPAKs
•X2 Modules
•Small Form-Factor Pluggable Modules (SFPs)
•10-Gigabit Ethernet Transceiver Modules
•DWDM-XFP Modules
•Power over Ethernet Daughtercards
•10/100/1000 Ethernet Switching Modules
•Fast Ethernet Switching Modules
•Ethernet/Fast Ethernet (10/100) Switching Modules
•Ethernet Switching Modules
•Optical Services Modules (OSMs)
•SPA Interface Processors (SIPs)
•SIP-400 Combinations
•Services SPA Carrier (SSC)
•Services SPAs
•Enhanced FlexWAN Module
•Enhanced FlexWAN Module Port Adapters
•Ethernet Services 20G Line Cards
•Ethernet Services 40G Line Cards
•ES+ Transport line cards start here
•Fan Trays
•Power Supplies
•Chassis
Note•Use the values in the "Power Required" column to determine the exact power requirements for your configuration to ensure that you are within the power budget.
•Daughtercard power is shown separately.
•Enter the show power command to display current system power usage.
Supervisor Engines
•Supervisor Engine 720
•Supervisor Engine 32
•Route Switching Processor 720
Supervisor Engine 720
•Supervisor Engine 720 Common Features
•Supervisor Engine 720 with PFC3BXL
•Supervisor Engine 720 with PFC3B
Supervisor Engine 720 Common Features
•Integrated 720-Gbps Switch Fabric
•64-MB bootflash device
•2 CompactFlash Type II slots (disk0 and disk1)
Note Some Supervisor Engine 720 Release 12.2SR images are larger than the bootflash device and must be stored on a CompactFlash card.
•Two Ethernet uplink ports:
–1-MB packet buffer per port
–Port 1—Gigabit Ethernet SFP
–Port 2—Configurable as Gigabit Ethernet SFP or 10/100/1000 Mbps RJ-45
•QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t
•Port grouping:
–Number of ports: 2
–Number of port groups: 1
–Port ranges per port group: 1-2
•Supervisor Engine 720 requires a high-capacity fan tray (see the "Fan Trays" section)
Supervisor Engine 720 with PFC3BXL
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-SUP720-3BXL
|
7.82 A@42 V
|
Supervisor Engine 720 with PFC3BXL:
•1-GB DRAM
•Policy Feature Card 3BXL (PFC3BXL); see the "RSP720-3C-10GE" section
•Multilayer Switch Feature Card 3 (MSFC3):
–1-GB DRAM
–64-MB bootflash
|
12.2(33)SRA
|
| |
Note There are no memory upgrade options for WS-SUP720-3BXL.
Supervisor Engine 720 with PFC3B
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-SUP720-3B
|
7.50 A@42 V
|
Supervisor Engine 720 with PFC3B:
•512-MB DRAM
•Policy Feature Card 3B (PFC3B); see the "RSP720-3C-10GE" section
•Multilayer Switch Feature Card 3 (MSFC3):
–512-MB DRAM
–64-MB bootflash
|
12.2(33)SRA
|
| |
Note
•There are no memory-only upgrade options for WS-SUP720-3B.
•Use WS-F6K-PFC3BXL= to upgrade a WS-SUP720-3B with a PFC3BXL. WS-F6K-PFC3BXL= includes 1 GB memory upgrades for the Supervisor Engine 720 and the MSFC3. Refer to this publication for more information:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/cfgnotes/78_16220.htm
Supervisor Engine 32
Note Supervisor Engine 32 does not support this hardware:
•WS-SUP720-3B
•WS-F6K-PFC3BXL—Policy Feature Card 3BXL (PFC3BXL)
•Distributed Forwarding Cards (DFCs) (installed DFCs do not power up with a Supervisor Engine 32)
•Switch Fabric Modules
•These switching modules:
–WS-X6704-10GE—4-port 10-Gigabit Ethernet XENPAK
–WS-X6748-SFP—48-port Gigabit Ethernet SFP
–WS-X6724-SFP—24-port Gigabit Ethernet SFP
–WS-X6816-GBIC—16-port Gigabit Ethernet GBIC
–WS-X6748-GE-TX—48-port 10/100/1000 RJ-45
•7600-SIP-600—SPA Interface Processor-600
•Optical Services Modules (OSMs)
•CISCO7603—3-slot chassis
•These service modules:
–WS-SVC-AON-1-K9—Application-Oriented Networking Module
–WS-SVC-AGM-1-K9—Anomaly Guard Module
–WS-SVC-ADM-1-K9—Traffic Anomaly Detector Module
–WS-SVC-MWAM-1—Multi-Processor WAN Application Module
•Supervisor Engine 32 does not support these software features and commands:
–Protocol independent multicast (PIM) snooping designated-router flooding configurability
–NetFlow version 9
–Egress multicast replication
–Multicast replication mode detection
–All fabric configuration commands
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-SUP32-10GE-3B
|
2.39 A@42 V
|
Supervisor Engine 32:
•One 10/100/1000 Mbps RJ-45 port
•WS-SUP32-10GE—two Gigabit Ethernet ports (requires XENPAKs)
•WS-SUP32-GE—eight Gigabit Ethernet SFP ports (requires Gigabit Ethernet SFPs)
•512-MB DRAM
•256-MB bootflash
•Policy Feature Card 3B (PFC3B); see the "RSP720-3C-10GE" section
•Multilayer Switch Feature Card 2A (MSFC2A):
–512-MB DRAM
–64-MB bootflash
|
12.2(33)SRA
|
WS-SUP32-GE-3B
|
1.89 A@42 V
|
| |
Note See this publication for Supervisor Engine 32 hardware information: http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/6000hw/supe_gd/index.htm
Route Switching Processor 720
RSP 720 Common Features
•Two Gigabit Ethernet uplink ports: port 1 supports a 1-Gbps small form pluggable (SFP) module; port 2 is configurable with either a 1-Gbps SFP module or a 10/100/1000-Mbps RJ-45
•Integrated 720-Gbps switch fabric
•Two CompactFlash Type II slots (on front panel) and 2-GB internal CompactFlash (1 GB each for RP and SP)
•Requires larger power supplies and a high-speed fan tray
•QoS port architecture (Rx/Tx) is 1p1q4t/1p2q2t
RSP720-3C-GE
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
RSP720-3C-GE
|
6.66 A@42 V
|
Route Switch Processor 720 with PFC3C:
•Two Gigabit Ethernet uplink ports: port 1 supports a 1-Gbps small form pluggable (SFP) module; port 2 is configurable with either a 1-Gbps SFP module or a 10/100/1000-Mbps RJ-45
•Integrated 720-Gbps switch fabric
•PFC3C and MSFC4 with 512-MB bootflash, 4-MB NVRAM, 4-MB ROMMON, and several DRAM options:
–Route processor (RP): 1- to 4-GB DRAM (default 1 GB)
–Switch processor (SP): 1- to 2-GB DRAM (default 1 GB)
•2 CompactFlash Type II slots (on front panel) and 2-GB internal CompactFlash (1 GB each for RP and SP)
•Requires larger power supplies and a high-speed fan tray
•QoS port architecture (Rx/Tx) is 1p1q4t/1p2q2t
|
12.2(33)SRB
|
| |
Note
•There are no memory-only upgrade options for RSP720-3C-GE.
•The following hardware and features are not supported by the RSP720-3C-GE:
–CISCO7603 router, OSR-7609 router.
–Optical Service Modules (OSMs), FlexWAN module (Enhanced FlexWAN module is supported).
–In-service software upgrade (ISSU) is not supported in Cisco IOS Release 12.2SRB.
–Server load balancing (SLB) is not supported.
•The RSP720-3C-GE supports the IPSEC-SPA-2G beginning with Cisco IOS Release 12.2(33)SRC.
RSP720-3CXL-GE
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
RSP720-3CXL-GE
|
7.33 A@42 V
|
Route Switch Processor 720 with PFC3CXL:
•Two Gigabit Ethernet uplink ports: port 1 supports a 1-Gbps small form pluggable (SFP) module; port 2 is configurable with either a 1-Gbps SFP module or a 10/100/1000-Mbps RJ-45
•Integrated 720-Gbps switch fabric
•PFC3CXL (high-capacity) and MSFC4 with 512-MB bootflash, 4-MB NVRAM, 4-MB ROMMON, and several DRAM options:
–Route processor (RP): 1- to 4-GB DRAM (default 2 GB)
–Switch processor (SP): 1- to 2-GB DRAM (default 1 GB)
•2 CompactFlash Type II slots (on front panel) and 2-GB internal CompactFlash (1 GB each for RP and SP)
•Requires larger power supplies and a high-speed fan tray
•QoS port architecture (Rx/Tx) is 1p1q4t/1p2q2t
|
12.2(33)SRB
|
| |
Note
•There are no memory-only upgrade options for RSP720-3CXL-GE.
•The RSP720-3CXL SP has one miniDIMM socket that accepts any vendor's 2GB DIMM. However, the RSP720-3CXL RP has two miniDIMM sockets. You must use the DIMMs from the same vendor for these sockets.
•The following hardware and features are not supported by the RSP720-3CXL-GE :
–Unsupported chassis: CISCO7603, OSR-7609.
–Unsupported modules: Optical Service Modules (OSMs), FlexWAN module (Enhanced FlexWAN module is supported).
–In-service software upgrade (ISSU) is not supported in Cisco IOS Release 12.2SRB.
–Server load balancing (SLB) is not supported.
•The RSP720-3CXL-GE supports the IPSEC-SPA-2G beginning with Cisco IOS Release 12.2(33)SRC.
RSP720-3C-10GE
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
RSP720-3C-10GE
|
7.33 A@42 V
|
Route Switch Processor 720 with uplink ports:
•Two 10 Gigabit Ethernet (10-GE) uplink ports support 10-Gbps X2 modules
•Three Gigabit Ethernet (1-GE) uplink ports: two ports support 1-Gbps small form-factor pluggable (SFP) module; one port supports 10/100/1000-Mbps RJ-45 connector
•Integrated 720-Gbps switch fabric
•PFC3C and MSFC4 with 512-MB bootflash, 4-MB NVRAM, 4-MB ROMmon, and several DRAM options:
–Route processor (RP): 1- to 2-GB DRAM (default 1 GB)
–Switch processor (SP): 1- to 2-GB DRAM (default 1 GB)
•One CompactFlash Type II slot (on front panel) and one 2-GB internal CompactFlash (1 GB each for RP and SP)
•Requires larger power supplies and a high-speed fan tray
•QoS port architecture, 10-GE ports (Rx/Tx): 8q8t/1p7q8t (CoS)
•QoS port architecture, 1-GE ports (Rx/Tx): 2q8t/1p3q8t
|
12.2(33)SRC
|
| |
Note
•Cisco IOS Release 12.2(33)SRE adds X2-DWDM and X2-10GB-LRM, X2 10GB-ZR support.
•There are no memory-only upgrade options for the RSP720-3C-10GE.
•The RSP720-3C-10GE does not support the following chassis and modules:
–Unsupported chassis: Cisco 7603 and 7606.
Note Cisco 7613 rev 05 backplane support RSP720-3C-10GE and RSP720-3CXL-10GE from 12.2(33)SRE onwards.
–Unsupported modules: Services modules (excluding the Network Analysis Module) , Optical Service Modules (OSMs), FlexWAN module.
•The RSP720-3C-10GE supports the following 10-Gigabit Ethernet optics: X2-10GB-LR, X2-10GB-ER, X2-10GB-SR, X2-10GB-CX4, and X2-10GB-LX4.
•The RSP720-3C-10GE supports the following Gigabit Ethernet optics: GLC-SX-MM, GLC-LH-SM, GLC-ZX-SM, GLC-T, SFP-GE-S, SFP-GE-L, SFP-GE-T, GLC-BX-D, and GLC-BX-U.
In Cisco IOS Release 12.2(33)SRE, the RSP720-10GE adds support for the following features:
•High-availability features such as NonStop Forwarding with Stateful Switchover (NSF/SSO) and In-Service Software Upgrade (ISSU) are not supported.
•The uplinks on the standby RSP720-10GE are active.
•Broadband Aggregation features are supported.
In Cisco IOS Release 12.2SRC, the RSP720-10GE does not support the following features, which are supported on the RSP720:
•High-availability features such as NonStop Forwarding with Stateful Switchover (NSF/SSO) and In-Service Software Upgrade (ISSU) are not supported. Only Route Processor Redundancy (RPR) mode is supported.
•The uplinks on the standby RSP720-10GE are not active. This restriction exists because the uplink ports must perform lookups on the active RSP, which is not possible in RPR mode.
•Broadband aggregation features are not supported.
•The RSP720-10GE is on limited orderability. General orderability is expected with the 12.2(33)SRE release.
RSP720-3CXL-10GE
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
RSP720-3CXL-10GE
|
7.33 A@42 V
|
Route Switch Processor 720 with PFC3CXL:
•Two 10 Gigabit Ethernet (10-GE) uplink ports support 10-Gbps X2 modules
•Three Gigabit Ethernet (1-GE) uplink ports: two ports support 1-Gbps small form-factor pluggable (SFP) module; one port supports 10/100/1000-Mbps RJ-45 connector
•Integrated 720-Gbps switch fabric
•PFC3CXL (high-capacity) and MSFC4 with 512-MB bootflash, 4-MB NVRAM, 4-MB ROMmon, and several DRAM options:
–Route processor (RP): 1- to 2-GB DRAM (default 2 GB)
–Switch processor (SP): 1- to 2-GB DRAM (default 1 GB)
•One CompactFlash Type II slot (on front panel) and one 2-GB internal CompactFlash (1 GB each for RP and SP)
•Requires larger power supplies and a high-speed fan tray
•QoS port architecture, 10-GE ports (Rx/Tx): 8q8t/1p7q8t (CoS)
•QoS port architecture, 1-GE ports (Rx/Tx): 2q8t/1p3q8t
|
12.2(33)SRC
|
| |
Note
•Cisco IOS Release 12.2(33)SRE adds X2-DWDM and X2-10GB-LRM, X2 10GB-ZR support.
•There are no memory-only upgrade options for the RSP720-3CXL-10GE.
•The RSP720-3CXL-10GE does not support the following chassis and modules:
–Unsupported chassis: Cisco 7603 and 7606.
Note Cisco 7613 rev 05 backplane support RSP720-3C-10GE and RSP720-3CXL-10GE from 12.2(33)SRE onwards.
–Unsupported modules: Services modules (excluding the Network Analysis Module) , Optical Service Modules (OSMs), FlexWAN module.
•The RSP720-3CXL-10GE supports the following 10-Gigabit Ethernet optics: X2-10GB-LR, X2-10GB-ER, X2-10GB-SR, X2-10GB-CX4, and X2-10GB-LX4.
•The RSP720-3CXL-10GE supports the following Gigabit Ethernet optics: GLC-SX-MM, GLC-LH-SM, GLC-ZX-SM, GLC-T, SFP-GE-S, SFP-GE-L, SSFP-GE-T, GLC-BX-D, and GLC-BX-U.
In Cisco IOS Release 12.2(33)SRE, the RSP720-10GE adds support for the following features:
•High-availability features such as NonStop Forwarding with Stateful Switchover (NSF/SSO) and In-Service Software Upgrade (ISSU) are not supported.
•The uplinks on the standby RSP720-10GE are active.
•Broadband Aggregation features are supported.
In Cisco IOS Release 12.2SRC, the RSP720-3CXL-10GE does not support the following features, which are supported on the RSP720:
•High-availability features such as NonStop Forwarding with Stateful Switchover (NSF/SSO) and In-Service Software Upgrade (ISSU) are not supported. Only Route Processor Redundancy (RPR) mode is supported.
•The uplinks on the standby RSP720-10GE are not active. This restriction exists because the uplink ports must perform lookups on the active RSP, which is not possible in RPR mode.
•Broadband aggregation features are not supported.
•The RSP720-1GE is on limited orderability. General orderability is expected with the 12.2(33)SRE release.
Policy Feature Cards
•Policy Feature Card Guidelines and Restrictions
•Policy Feature Card 3BXL
•Policy Feature Card 3B
•Distributed and Centralized Forwarding Cards
Policy Feature Card Guidelines and Restrictions
•The PFC3 supports a theoretical maximum of 64,000 MAC addresses (32,000 MAC addresses recommended maximum).
•You cannot use one type of PFC3 (PFC3BXL or PFC3B) on one supervisor engine and a different type on the other supervisor engine for redundancy. You must use identical policy feature cards for redundancy.
•Enter the show platform hardware pfc mode command to display the PFC3 mode.
•Enter the show platform earl-mode command to display the PFC3 mode.
•PFC3B—These restrictions apply to a configuration with a PFC3B and these DFCs:
–PFC3B and DFC3B—No restrictions.
–PFC3B and DFC3BXL—The PFC3B restricts DFC3BXL functionality: after a reload with a DFC3BXL-equipped module installed, the DFC3BXL functions as a DFC3B.
•PFC3BXL—These restrictions apply to a configuration with a PFC3BXL and these DFCs:
–PFC3BXL and DFC3B—PFC3BXL functionality is restricted by the DFC3B: after a reload with a DFC3B-equipped module installed (whether powered up or down), the PFC3BXL functions as a PFC3B.
–PFC3BXL and DFC3BXL—No restrictions.
•The features that require the PFC3BXL or PFC3B are not supported in PFC3A mode (see the Release Notes for Cisco IOS Release 12.2SR on the Cisco 7600 Series Routers).
•To use DFC3B-equipped switching modules with a PFC3BXL, the DFC3B-equipped switching modules must be installed at bootup.
Policy Feature Card 3BXL
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-F6K-PFC3BXL
|
2.57 A@42 V
|
Policy Feature Card 3BXL (PFC3BXL)
|
| |
Supported only with Supervisor Engine 720
|
12.2(33)SRA
|
Note
•There are no memory upgrade options for WS-F6K-PFC3BXL.
•Use WS-F6K-PFC3BXL= to upgrade a WS-SUP720 or WS-SUP720-3B with a PFC3BXL. WS-F6K-PFC3BXL= includes 1 GB memory upgrades for the Supervisor Engine 720 and the MSFC3. Refer to this publication for more information:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/cfgnotes/78_16220.htm
|
Policy Feature Card 3B
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-F6K-PFC3B
|
2.25 A@42 V
|
Policy Feature Card 3B (PFC3B)
|
With Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
Note
•There are no memory upgrade options for WS-F6K-PFC3B.
•Use WS-F6K-PFC3BXL= to upgrade a WS-SUP720-3B with a PFC3BXL. WS-F6K-PFC3BXL= includes 1 GB memory upgrades for the Supervisor Engine 720 and the MSFC3. Refer to this publication for more information:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/cfgnotes/78_16220.htm
|
Policy Feature Card 3C
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-F6K-PFC3C
|
2.25 A@42 V
|
Policy Feature Card 3C (PFC3C)
|
| |
|
Supported only with RSP 720
|
12.2(33)SRB
|
Note
•There are no memory upgrade options for WS-F6K-PFC3C.
|
Policy Feature Card 3CXL
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-F6K-PFC3CXL
|
2.57 A@42 V
|
Policy Feature Card 3CXL (PFC3CXL)
|
| |
Supported only with RSP 720
|
12.2(33)SRB
|
Note
•There are no memory upgrade options for WS-F6K-PFC3BXL.
|
Distributed and Centralized Forwarding Cards
•Centralized Forwarding Card (WS-X6700-CFC)
•Distributed Forwarding Card 3BXL
•Distributed Forwarding Card 3B
•Distributed Forwarding Card 3CXL
•Distributed Forwarding Card 3C
Note See the "Route Switching Processor 720" section for Policy Feature Cards (PFC) and Distributed Forwarding Card (DFC) restrictions.
Centralized Forwarding Card (WS-X6700-CFC)
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-X6700-CFC
|
0.75 A@42 V
|
Centralized Forwarding Card (CFC) for use on CEF720 modules
|
| |
Supported only with Supervisor Engine 720
|
12.2(33)SRA
|
Note There are no memory upgrade options for WS-X6700-CFC.
|
Distributed Forwarding Card 3BXL
•WS-F6700-DFC3BXL
•WS-F6K-DFC3BXL
WS-F6700-DFC3BXL
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-F6700-DFC3BXL
|
3.30 A@42 V
|
Distributed Forwarding Card 3BXL (DFC3BXL) for use on CEF720 modules
|
| |
Supported only with Supervisor Engine 720
|
12.2(33)SRA
|
Note
•WS-F6700-DFC3BXL uses memory that is installed on the switching module.
•Refer to this publication for information about WS-F6700-DFC3BXL upgrades:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/cfgnotes/78_15893.htm
|
WS-F6K-DFC3BXL
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-F6K-DFC3BXL
|
1.47 A@42 V
|
Distributed Forwarding Card 3BXL (DFC3BXL) for use on dCEF256 and CEF256 modules
|
| |
Supported only with Supervisor Engine 720
|
12.2(33)SRA
|
Note
•Refer to this publication for information about WS-F6K-DFC3BXL memory upgrades:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/cfgnotes/78_12409.htm
•Supervisor Engine 720 supports a WS-F6K-DFC3BXL on these WS-X6516-GBIC switching module hardware revisions:
–Lower than 5.0
–5.5 and higher
•Supervisor Engine 720 does not support a DFC3 on WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4. With a Supervisor Engine 720 and with a DFC3 installed, WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4 do not power up.
•With a Supervisor Engine 720 but without a DFC3, WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4 operate in bus mode.
•Refer to external field notice 24494 for more information about Supervisor Engine 720 and a DFC3 on WS-X6516-GBIC switching modules:
http://www.cisco.com/warp/public/770/fn24494.shtml
|
Distributed Forwarding Card 3B
•WS-F6700-DFC3B
•WS-F6K-DFC3B
WS-F6700-DFC3B
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-F6700-DFC3B
|
3.00 A@42 V
|
Distributed Forwarding Card 3B (DFC3B) for use on CEF720 modules
|
| |
Supported only with Supervisor Engine 720
|
12.2(33)SRA
|
Note
•WS-F6700-DFC3B uses memory that is installed on the switching module.
•Refer to this publication for information about WS-F6700-DFC3B upgrades:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/cfgnotes/78_15893.htm
|
WS-F6K-DFC3B
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-F6K-DFC3B
|
1.67 A@42 V
|
Distributed Forwarding Card 3B (DFC3B) for use on dCEF256 and CEF256 modules
|
| |
Supported only with Supervisor Engine 720
|
12.2(33)SRA
|
Note
•Refer to this publication for information about WS-F6K-DFC3B memory upgrades:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/cfgnotes/78_12409.htm
•Supervisor Engine 720 supports a WS-F6K-DFC3B on these WS-X6516-GBIC switching module hardware revisions:
–Lower than 5.0
–5.5 and higher
•Supervisor Engine 720 does not support a DFC3 on WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4. With a Supervisor Engine 720 and with a DFC3 installed, WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4 do not power up.
•With a Supervisor Engine 720 but without a DFC3, WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4 operate in bus mode.
•Refer to external field notice 24494 for more information about Supervisor Engine 720 and a DFC3 on WS-X6516-GBIC switching modules:
http://www.cisco.com/warp/public/770/fn24494.shtml
|
Distributed Forwarding Card 3CXL
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-F6700-DFC3CXL
|
2.35 A@42 V
|
Distributed Forwarding Card 3CXL (DFC3CXL) for use on CEF720 modules
|
| |
Supported with Supervisor Engine 720 and Route Switch Processor 720
|
12.2(33)SRB
|
Distributed Forwarding Card 3C
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-F6700-DFC3C
|
1.65 A@42 V
|
Distributed Forwarding Card 3C (DFC3C) for use on CEF720 modules
|
| |
Supported with Supervisor Engine 720 and Route Switch Processor 720
|
12.2(33)SRB
|
10-Gigabit Ethernet Switching Modules
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-X6704-10GE
|
6.28 A@42 V
|
4-port 10-Gigabit Ethernet XENPAK
•CEF720 with WS-X6700-CFC (adds 0.75 A@42 V)
•dCEF720 with WS-F6700-DFC3BXL (adds 3.30 A@42 V)
•dCEF720 with WS-F6700-DFC3B (adds 3.00 A@42 V)
•Supports egress multicast replication
•QoS port architecture (Rx/Tx):
–With DFC3: 8q8t/1p7q8t
–With CFC: 1q8t/1p7q8t
•Number of ports: 4
Number of port groups: 4
Port ranges per port group: 1 port in each group
|
| |
Supported only with Supervisor Engine 720
|
12.2(33)SRA
|
Note
•WS-X6704-10GE requires one of the following:
–WS-F6700-DFC3BXL (3.30 A@42 V)
–WS-F6700-DFC3B (3.00 A@42 V)
–WS-X6700-CFC (0.75 A@42 V)
•WS-X6704-10GE ships with WS-X6700-CFC installed unless ordered with WS-F6700-DFC3BXL or WS-F6700-DFC3B.
•WS-X6704-10GE is supported in the WS-C6503-E chassis.
•WS-X6704-10GE is not supported in the WS-C6503 and CISCO7603 chassis.
•In a 13-slot chassis, WS-X6704-10GE is supported only in slots 9 through 13 and does not power up in other slots.
•On WS-X6704-10GE ports, Spanning Tree Protocol (STP) bridge protocol data units (BPDUs) are not exempt from Traffic Storm Control suppression. Do not configure Traffic Storm Control on STP-protected WS-X6704-10GE ports that interconnect network devices.
|
WS-X6502-10GE
|
3.30 A@42 V
|
1-port 10-Gigabit Ethernet
•With Supervisor Engine 720:
–dCEF256 with WS-F6K-DFC3BXL (adds 1.47 A@42 V)
–dCEF256 with WS-F6K-DFC3B (adds 1.67 A@42 V)
•QoS port architecture (Rx/Tx): 1p1q8t/1p2q1t
•Number of ports: 1
Number of port groups: 1
Port ranges per port group: 1 port in 1 group
|
|
With Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
Note WS-X6502-10GE does not support Inter-Switch Link (ISL) encapsulation.
|
Optical Interface Module (OIM) for WS-X6502-10GE
|
WS-G6488
|
10GBASE-LR serial 1310 nm long-reach OIM
|
12.2(33)SRA
|
WS-G6483
|
10GBASE-ER serial 1550 nm extended-reach OIM
|
12.2(33)SRA
|
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
|
|
10.58A @42 V
|
8-port 10-Gigabit Ethernet X2module
•dCEF720
•Supports egress multicast replication
•QoS port architecture (Rx/Tx): 8q4t/1p7q4t
•Dual switch-fabric connections
Fabric Channel #1: Ports 2, 3, 6, 8
Fabric Channel #2: Ports 1, 4, 5, 7
•Number of ports: 8
Number of port groups: 8
Port ranges per port group: 1 port in each group
|
|
|
11.28A @ 42V
|
| |
Supported only with Supervisor Engine 720, Route Switch Processor 720, and RSP720-10GE.
|
12.2(33)SRC
|
| |
|
X2 Modules Supported in Gigabit Ethernet SPAs
|
|
| |
|
X2-10GB-SR
|
12.2(33)SRC
|
| |
|
X2-10GB-CX4
|
12.2(33)SRC
|
| |
|
X2-10GB-LX4
|
12.2(33)SRC
|
| |
|
X2-10GB-ER
|
12.2(33)SRC
|
| |
|
X2-10GB-LR
|
12.2(33)SRC
|
| |
|
X2-10GB-LRM
|
12.2(33)SRE
|
| |
|
X2 10GB-ZR
|
12.2(33)SRE
|
| |
|
X2-DWDMs
|
12.2(33)SRE
|
Note
•To configure WS-X6708-10GE port oversubscription, refer to the hw-module oversubscription command in the command reference at this URL:
http://www.cisco.com/en/US/products/ps6922/prod_command_reference_list.html
•Installation of a WS-X6708-10GE switching module in a chassis other than the following prevents operation at levels that are fully NEBS-compliant:
–WS-C6503-E
–WS-C6504-E
–WS-C6506-E
–WS-C6509-E
–WS-C6509-NEB-A with dual fan tray
–CISCO7604
–CISCO7609 with dual fan tray
•WS-X6708-10G-3C and WS-X6708-10G-3CXL are the orderable product IDs.
•The front panel is labeled WS-X6708-10GE.
•Cisco IOS software commands display WS-X6708-10GE with either WS-F6700-DFC3C or WS-F6700-DFC3CXL.
•WS-X6708-10GE ports do not support VACL capture. (CSCsb59015)
•WS-X6708-10GE is not supported in the WS-C6503 and CISCO7603 chassis.
•In a 13-slot chassis, WS-X6708-10GE is supported only in slots 9 through 13 and does not power up in other slots.
•On WS-X6708-10GE ports, STP BPDUs are not exempt from Traffic Storm Control suppression. Do not configure Traffic Storm Control on STP-protected WS-X6708-10GE ports that interconnect network devices.
|
XENPAKs
Product ID
(append "=" for spares)
|
Product Description
|
Minimum Software Version
|
DWDM-XENPAK
|
10GBASE dense wavelength division multiplexing (DWDM) 100-GHz ITU grid
|
12.2(33)SRA
|
WDM-XENPAK-REC
|
10GBASE receive-only wavelength division multiplexing (WDM)
|
12.2(33)SRA
|
XENPAK-10GB-CX4
|
10GBASE for CX4 cable
|
12.2(33)SRA
|
XENPAK-10GB-SR
|
10GBASE-SR Serial 850-nm short-reach multimode fiber (MMF)
|
12.2(33)SRA
|
XENPAK-10GB-LX4
|
10GBASE-LX4 Serial 1310-nm multimode fiber (MMF)
|
12.2(33)SRA
|
XENPAK-10GB-ER
|
10GBASE-ER Serial 1550-nm extended-reach, single-mode fiber (SMF), dispersion-shifted fiber (DSF)
|
12.2(33)SRA
|
Note XENPAK-10GB-ER units is not supported with Part Number 800-24557-01, as described in this external field notice (CSCee47030):
http://www.cisco.com/warp/public/770/fn29736.shtml
|
XENPAK-10GB-LR
|
10GBASE-LR Serial 1310-nm long-reach, single-mode fiber (SMF), dispersion-shifted fiber (DSF)
|
12.2(33)SRA
|
X2 Modules
Product ID
(append "=" for spares)
|
Product Description
|
Minimum Software Version
|
X2-10GB-SR
|
10GBASE-SR Serial 850-nm short-reach multimode (MMF)
|
12.2(33)SRC
|
X2-10GB-CX4
|
10GBASE for CX4 (copper) cable
|
12.2(33)SRC
|
X2-10GB-LX4
|
10GBASE-LX4 Serial 1310-nm multimode (MMF)
|
12.2(33)SRC
|
X2-10GB-LR
|
10GBASE-LR Serial 1310-nm long-reach, single-mode fiber (SMF), dispersion-shifted fiber (DSF)
|
12.2(33)SRC
|
X2-10GB-ER
|
10GBASE-ER Serial 1550-nm extended-reach, single-mode fiber (SMF), dispersion-shifted fiber (DSF)
|
12.2(33)SRC
|
Gigabit Ethernet Switching Modules
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-X6748-SFP
|
5.32 A@42 V
|
48-port Gigabit Ethernet SFP
•CEF720 with WS-X6700-CFC (adds 0.75 A@42 V)
•dCEF720 with WS-F6700-DFC3BXL (adds 3.30 A@42 V)
•dCEF720 with WS-F6700-DFC3B (adds 3.00 A@42 V)
•Supports egress multicast replication
•QoS architecture:
–With DFC3: 2q8t/1p3q8t
–With CFC: 1q8t/1p3q8t
•Number of ports: 48
Number of port groups: 4
Port ranges per port group:
1, 3, 5, 7, 9, 11, 13, 15, 17, 19, 21, 23
2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24
25, 27, 29, 31, 33, 35, 37, 39, 41, 43, 45, 47
26, 28, 30, 32, 34, 36, 38, 40, 42, 44, 46, 48
|
| |
Supported only with Supervisor Engine 720
|
12.2(33)SRA
|
| |
SFPs Supported
|
| |
|
GLC-T=
|
12.2(33)SRA
|
| |
|
GLC-SX-MM=
|
12.2(33)SRA
|
| |
|
GLC-LH-SM=
|
12.2(33)SRA
|
| |
|
GLC-ZX-SM=
|
12.2(33)SRA
|
| |
|
GLC-BX-D=
|
12.2(33)SRA
|
| |
|
GLC-BX-U=
|
12.2(33)SRA
|
| |
|
CWDM-SFP-xxxx=
|
12.2(33)SRA
|
| |
|
SFP-GE-S
|
12.2(33)SRB
|
| |
|
SFP-GE-L
|
12.2(33)SRB
|
| |
|
SFP-GE-Z
|
12.2(33)SRB
|
| |
|
SFP-GE-T
|
12.2(33)SRB
|
| |
|
SFP-GE-T
|
12.2(33)SRD2
|
Note
•WS-X6748-SFP requires one of the following:
–WS-F6700-DFC3BXL (3.30 A@42 V)
–WS-F6700-DFC3B (3.00 A@42 V)
–WS-X6700-CFC (0.75 A@42 V)
•WS-X6748-SFP ships with WS-X6700-CFC installed unless ordered with WS-F6700-DFC3BXL or WS-F6700-DFC3B.
•WS-X6748-SFP is supported in the WS-C6503-E chassis.
•WS-X6748-SFP is not supported in the WS-C6503 and CISCO7603 chassis.
•In a 13-slot chassis, WS-X6748-SFP is supported only in slots 9 through 13 and does not power up in other slots.
•On WS-X6748-SFP ports, STP BPDUs are not exempt from Traffic Storm Control suppression. Do not configure Traffic Storm Control on STP-protected WS-X6748-SFP ports that interconnect network devices.
•See the "Small Form-Factor Pluggable Modules (SFPs)" section.
|
WS-X6724-SFP
|
2.23 A@42 V
|
24-port Gigabit Ethernet SFP
•CEF720 with WS-X6700-CFC (adds 0.75 A@42 V)
•dCEF720 with WS-F6700-DFC3BXL (adds 3.30 A@42 V)
•dCEF720 with WS-F6700-DFC3B (adds 3.00 A@42 V)
•Supports egress multicast replication
•QoS architecture:
–With DFC3: 2q8t/1p3q8t
–With CFC: 1q8t/1p3q8t
•Number of ports: 24
Number of port groups: 2
Port ranges per port group: 1-12, 13-24
|
| |
Supported only with Supervisor Engine 720
|
12.2(33)SRA
|
| |
SFPs Supported
|
| |
|
GLC-T=
|
12.2(33)SRA
|
| |
|
GLC-SX-MM=
|
12.2(33)SRA
|
| |
|
GLC-LH-SM=
|
12.2(33)SRA
|
| |
|
GLC-ZX-SM=
|
12.2(33)SRA
|
| |
|
GLC-BX-D=
|
12.2(33)SRA
|
| |
|
GLC-BX-U=
|
12.2(33)SRA
|
| |
|
CWDM-SFP-xxxx=
|
12.2(33)SRA
|
| |
|
SFP-GE-S
|
12.2(33)SRB
|
| |
|
SFP-GE-L
|
12.2(33)SRB
|
| |
|
SFP-GE-Z
|
12.2(33)SRB
|
| |
|
SFP-GE-T
|
12.2(33)SRB
|
Note
•WS-X6724-SFP requires one of the following:
–WS-F6700-DFC3BXL (3.30 A@42 V)
–WS-F6700-DFC3B (3.00 A@42 V)
–WS-X6700-CFC (0.75 A@42 V)
•WS-X6724-SFP ships with WS-X6700-CFC installed unless ordered with WS-F6700-DFC3BXL or WS-F6700-DFC3B.
•WS-X6724-SFP is supported in the WS-C6503-E chassis.
•WS-X6724-SFP is not supported in the WS-C6503 and CISCO7603 chassis.
•On WS-X6724-SFP ports, STP BPDUs are not exempt from Traffic Storm Control suppression. Do not configure Traffic Storm Control on STP-protected WS-X6724-SFP ports that interconnect network devices.
•See the "Small Form-Factor Pluggable Modules (SFPs)" section.
|
WS-X6816-GBIC
|
3.84 A@42 V
|
16-port Gigabit Ethernet GBIC
|
|
| |
|
•dCEF256
•QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t
Number of ports: 16
Number of port groups: 2
Port ranges per port group: 1-8, 9-16
|
|
With Supervisor Engine 720
|
12.2(33)SRA
|
Note
•WS-X6816-GBIC requires one of these for use with Supervisor Engine 720:
–WS-F6K-DFC3BXL (adds 1.47 A@42 V)
–WS-F6K-DFC3B (adds 1.67 A@42 V)
•In a 13-slot chassis, WS-X6816-GBIC is supported only in slots 9 through 13 and does not power up in other slots.
|
WS-X6516A-GBIC
|
3.62 A@42 V
|
16-port Gigabit Ethernet GBIC
•CEF256
•With Supervisor Engine 720:
–dCEF256 with WS-F6K-DFC3BXL (adds 1.47 A@42 V)
–dCEF256 with WS-F6K-DFC3B (adds 1.67 A@42 V)
•1-MB per-port packet buffers
•Supports egress multicast replication
•QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t
•Number of ports: 16
Number of port groups: 2
Port ranges per port group: 1-8, 9-16
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
WS-X6516-GBIC
|
3.40 A@42 V
|
16-port Gigabit Ethernet GBIC
•CEF256
•With Supervisor Engine 720:
–dCEF256 with WS-F6K-DFC3BXL (adds 1.47 A@42 V)
–dCEF256 with WS-F6K-DFC3B (adds 1.67 A@42 V)
•512-KB per-port packet buffers
•QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t
•Number of ports: 16
Number of port groups: 2
Port ranges per port group: 1-8, 9-16
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
Note
•Supervisor Engine 720 supports a DFC3 on these WS-X6516-GBIC hardware revisions:
–Lower than 5.0
–5.5 and higher
•Supervisor Engine 720 does not support a DFC3 on WS-X6516-GBIC hardware revisions 5.0 through 5.4. With a Supervisor Engine 720 and with a DFC3 installed, WS-X6516-GBIC hardware revisions 5.0 through 5.4 do not power up.
•With a Supervisor Engine 720 but without a DFC3, WS-X6516-GBIC hardware revisions 5.0 through 5.4 operate in bus mode.
•Refer to external field notice 24494 for more information:
http://www.cisco.com/warp/public/770/fn24494.shtml
|
WS-X6416-GBIC
|
2.81 A@42 V
|
16-port Gigabit Ethernet GBIC
•QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t
•Number of ports: 16
Number of port groups: 2
Port ranges per port group: 1-8, 9-16
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
WS-X6416-GE-MT
|
2.50 A@42 V
|
16-Port Gigabit Ethernet MT-RJ
•QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t
•Number of ports: 16
Number of port groups: 2
Port ranges per port group: 1-8, 9-16
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
WS-X6316-GE-TX
|
5.15 A@42 V
|
16-port Gigabit Ethernet RJ-45
•QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t
•Number of ports: 16
Number of port groups: 2
Port ranges per port group: 1-8, 9-16
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
Note Supervisor Engine 32 does not support WS-X6316-GE-TX.
|
WS-X6408A-GBIC
|
2.00 A@42 V
|
8-port Gigabit Ethernet GBIC
•QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t
•Number of ports: 8
Number of port groups: 1
Port ranges per port group: 1-8
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
WS-X6408-GBIC
|
2.00 A@42 V
|
8-port Gigabit Ethernet GBIC
•QoS port architecture (Rx/Tx): 1q4t/2q2t
•Number of ports: 8
Number of port groups: 1
Port ranges per port group: 1-8
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
Small Form-Factor Pluggable Modules (SFPs)
These sections describe SFPs:
•Gigabit Ethernet SFPs
•Fast Ethernet SFPs
Gigabit Ethernet SFPs
See the Unsupported Hardware section for information about unsupported DWDM-SFPs.
Note Because there are no configurable PIDs, all CWDM and DWDM optics must be ordered as spares.
Product ID
(append "=" for spares)
|
Product Description
|
Minimum Software Version
|
GLC-ZX-SM
|
1000BASE-ZX SFP
|
12.2(33)SRA
|
CWDM-SFP
|
1000BASE-CWDM SFP
|
12.2(33)SRA
|
GLC-T
|
1000BASE-T SFP
|
12.2(33)SRA
|
GLC-LH-SM
|
1000BASE-LX/LH SFP
|
12.2(33)SRA
|
GLC-SX-MM
|
1000BASE-SX SFP
|
12.2(33)SRA
|
SFP-GE-S
|
1000BASE-SX SFP
|
12.2(33)SRA
|
SFP-GE-L
|
1000BASE-LX/LH SFP
|
12.2(33)SRA
|
SFP-GE-Z
|
1000BASE-ZX SFP
|
12.2(33)SRA
|
SFP-GE-T
|
1000BASE-T SFP
|
12.2(33)SRB3
|
CWDM-SFP-1470
|
1000BASE-CWDM SFP 1470 nm
|
12.2(33)SRB3
|
CWDM-SFP-1490
|
1000BASE-CWDM SFP 1490 nm
|
12.2(33)SRB3
|
CWDM-SFP-1510
|
1000BASE-CWDM SFP 1510 nm
|
12.2(33)SRB3
|
CWDM-SFP-1530
|
1000BASE-CWDM SFP 1530 nm
|
12.2(33)SRB3
|
CWDM-SFP-1550
|
1000BASE-CWDM SFP 1550 nm
|
12.2(33)SRB3
|
CWDM-SFP-1570
|
1000BASE-CWDM SFP 1570 nm
|
12.2(33)SRB3
|
CWDM-SFP-1590
|
1000BASE-CWDM SFP 1590 nm
|
12.2(33)SRB3
|
CWDM-SFP-1610
|
1000BASE-CWDM SFP 1610 nm
|
12.2(33)SRB3
|
Fast Ethernet SFPs
Note Only WS-X6148-FE-SFP supports these Fast Ethernet SFPs.
Product ID
(append "=" for spares)
|
Product Description
|
Minimum Software Version
|
GLC-FE-100FX
|
100BASEFX SFP
|
12.2(33)SRA
|
GLC-FE-100LX
|
100BASELX SFP
|
12.2(33)SRA
|
10-Gigabit Ethernet Transceiver Modules
Product ID
(append "=" for spares)
|
Product Description
|
Minimum Software Version
|
XFP-10GLR-OC192SR
|
Cisco multirate XFP transceiver module for 10GBASE-LR Ethernet and OC-192/STM-64 short-reach (SR-1) Packet-over-SONET/SDH (POS) applications, SMF, dual LC connector
|
12.2(33)SRA
|
XFP-10GER-OC192IR
|
Cisco multirate XFP transceiver module for 10GBASE-ER Ethernet and OC-192/STM-64 intermediate-reach (IR-2) Packet-over-SONET/SDH (POS) applications, SMF, dual LC connector
|
12.2(33)SRA
|
XFP-10GZR-OC192LR
|
Cisco multirate XFP transceiver module for 10GBASE-LR Ethernet and OC-192/STM-64 long-reach Packet-over-SONET/SDH (POS) applications, SMF, dual LC connector
|
12.2(33)SRB1
|
DWDM-XFP Modules
Note Because there are no configurable PIDs, all CWDM and DWDM optics must be ordered as spares.
Product ID
(append "=" for spares)
|
Product Description
|
Minimum Software Version
|
DWDM-XFP-30.33=
|
DWDM XFP 1530.33 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM-XFP-31.12=
|
DWDM XFP 1531.12 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM-XFP-31.90=
|
DWDM XFP 1531.90 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM- XFP-32.68=
|
DWDM XFP 1532.68 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM-XFP-34.25=
|
DWDM XFP 1535.25 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM-XFP-35.04=
|
DWDM XFP 1535.04 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM-XFP-35.82=
|
DWDM XFP 1535.82 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM- XFP-36.61=
|
DWDM XFP 1536.61 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM-XFP-38.19=
|
DWDM XFP 1538.19 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM-XFP-38.98v
|
DWDM XFP 1538.98 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM-XFP-39.77=
|
DWDM XFP 1539.77 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM- XFP-40.56=
|
DWDM XFP 1540.56 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM-XFP-42.14=
|
DWDM XFP 1542.14 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM-XFP-42.94=
|
DWDM XFP 1542.94 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM-XFP-43.73=
|
DWDM XFP 1543.73 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM- XFP-44.53=
|
DWDM XFP 1544.53 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM-XFP-46.12=
|
DWDM XFP 1546.12 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM-XFP-46.92=
|
DWDM XFP 1546.92 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM-XFP-47.72=
|
DWDM XFP 1547.72 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM-XFP-48.51=
|
DWDM XFP 1548.51 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM-XFP-50.12=
|
DWDM XFP 1550.12 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM-XFP-50.92=
|
DWDM XFP 1550.92 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM-XFP-51.72v
|
DWDM XFP 1551.72 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM-XFP-52.52=
|
DWDM XFP 1552.52 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM- XFP-54.13=
|
DWDM XFP 1554.13 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM-XFP-54.94=
|
DWDM XFP 1554.94 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM-XFP-55.75=
|
DWDM XFP 1555.75 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM-XFP-56.55=
|
DWDM XFP 1556.55 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM- XFP-58.17=
|
DWDM XFP 1558.17 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM-XFP-58.98=
|
DWDM XFP 1558.98 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM-XFP-59.79=
|
DWDM XFP 1559.79 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
DWDM- XFP-60.61=
|
DWDM XFP 1560.61 nm XFP (100 GHz ITU grid)
|
12.2(33)SRB3
|
Gigabit Interface Converters (GBICs)
Note The support listed in this section applies to all modules that use GBICs, including OSM LAN ports and OSM Gigabit Ethernet WAN ports.
Product ID
(append "=" for spares)
|
Product Description
|
Minimum Software Version
|
WDM-GBIC-REC
|
Receive-only wavelength division multiplexing (WDM) GBIC
|
12.2(33)SRA
|
DWDM-GBIC
|
Dense wavelength division multiplexing (DWDM) GBIC
|
12.2(33)SRA
|
CWDM-GBIC
|
Coarse wavelength division multiplexing (CWDM) GBIC
|
12.2(33)SRA
|
WS-G5483
|
1000BASET GBIC
|
12.2(33)SRA
|
WS-G5484
|
Short wavelength, 1000BASE-SX
|
12.2(33)SRA
|
WS-G5486
|
Long wavelength/long haul, 1000BASE-LX/LH
|
12.2(33)SRA
|
WS-G5487
|
Extended distance, 1000BASE-ZX
|
12.2(33)SRA
|
CWDM-GBIC-1470=
|
Cisco 1000BASE-CWDM GBIC 1470 nm
|
12.2(33)SRA
|
CWDM-GBIC-1490=
|
Cisco 1000BASE-CWDM GBIC 1490 nm
|
12.2(33)SRA
|
CWDM-GBIC-1510=
|
Cisco 1000BASE-CWDM GBIC 1510 nm
|
12.2(33)SRA
|
CWDM-GBIC-1530=
|
Cisco 1000BASE-CWDM GBIC 1530 nm
|
12.2(33)SRA
|
CWDM-GBIC-1550=
|
Cisco 1000BASE-CWDM GBIC 1550 nm
|
12.2(33)SRA
|
CWDM-GBIC-1570=
|
Cisco 1000BASE-CWDM GBIC 1570 nm
|
12.2(33)SRA
|
CWDM-GBIC-1590=
|
Cisco 1000BASE-CWDM GBIC 1590 nm
|
12.2(33)SRA
|
CWDM-GBIC-1610=
|
Cisco 1000BASE-CWDM GBIC 1610 nm
|
12.2(33)SRA
|
DWDM-GBIC-60.61=
|
1000BASE-DWDM GBIC 1560.61 nm
|
12.2(33)SRA
|
DWDM-GBIC-59.79=
|
1000BASE-DWDM GBIC 1559.79 nm
|
12.2(33)SRA
|
DWDM-GBIC-58.98=
|
1000BASE-DWDM GBIC 1558.98 nm
|
12.2(33)SRA
|
DWDM-GBIC-58.17=
|
1000BASE-DWDM GBIC 1558.17 nm
|
12.2(33)SRA
|
DWDM-GBIC-56.55=
|
1000BASE-DWDM GBIC 1556.55 nm
|
12.2(33)SRA
|
DWDM-GBIC-55.75=
|
1000BASE-DWDM GBIC 1555.75 nm
|
12.2(33)SRA
|
DWDM-GBIC-54.94=
|
1000BASE-DWDM GBIC 1554.94 nm
|
12.2(33)SRA
|
DWDM-GBIC-54.13=
|
1000BASE-DWDM GBIC 1554.13 nm
|
12.2(33)SRA
|
DWDM-GBIC-52.52=
|
1000BASE-DWDM GBIC 1552.52 nm
|
12.2(33)SRA
|
DWDM-GBIC-51.72=
|
1000BASE-DWDM GBIC 1551.72 nm
|
12.2(33)SRA
|
DWDM-GBIC-50.92=
|
1000BASE-DWDM GBIC 1550.92 nm
|
12.2(33)SRA
|
DWDM-GBIC-50.12=
|
1000BASE-DWDM GBIC 1550.12 nm
|
12.2(33)SRA
|
DWDM-GBIC-48.51=
|
1000BASE-DWDM GBIC 1548.51 nm
|
12.2(33)SRA
|
DWDM-GBIC-47.72=
|
1000BASE-DWDM GBIC 1547.72 nm
|
12.2(33)SRA
|
DWDM-GBIC-46.92=
|
1000BASE-DWDM GBIC 1546.92 nm
|
12.2(33)SRA
|
DWDM-GBIC-46.12=
|
1000BASE-DWDM GBIC 1546.12 nm
|
12.2(33)SRA
|
DWDM-GBIC-44.53=
|
1000BASE-DWDM GBIC 1544.53 nm
|
12.2(33)SRA
|
DWDM-GBIC-43.73=
|
1000BASE-DWDM GBIC 1543.73 nm
|
12.2(33)SRA
|
DWDM-GBIC-42.94=
|
1000BASE-DWDM GBIC 1542.94 nm
|
12.2(33)SRA
|
DWDM-GBIC-42.14=
|
1000BASE-DWDM GBIC 1542.14 nm
|
12.2(33)SRA
|
DWDM-GBIC-40.56=
|
1000BASE-DWDM GBIC 1540.56 nm
|
12.2(33)SRA
|
DWDM-GBIC-39.77=
|
1000BASE-DWDM GBIC 1539.77 nm
|
12.2(33)SRA
|
DWDM-GBIC-39.98=
|
1000BASE-DWDM GBIC 1539.98 nm
|
12.2(33)SRA
|
DWDM-GBIC-38.19=
|
1000BASE-DWDM GBIC 1538.19 nm
|
12.2(33)SRA
|
DWDM-GBIC-36.61=
|
1000BASE-DWDM GBIC 1536.61 nm
|
12.2(33)SRA
|
DWDM-GBIC-35.82=
|
1000BASE-DWDM GBIC 1535.82 nm
|
12.2(33)SRA
|
DWDM-GBIC-35.04=
|
1000BASE-DWDM GBIC 1535.04 nm
|
12.2(33)SRA
|
DWDM-GBIC-34.25=
|
1000BASE-DWDM GBIC 1534.25 nm
|
12.2(33)SRA
|
DWDM-GBIC-32.68=
|
1000BASE-DWDM GBIC 1532.68 nm
|
12.2(33)SRA
|
DWDM-GBIC-31.90=
|
1000BASE-DWDM GBIC 1531.90 nm
|
12.2(33)SRA
|
DWDM-GBIC-31.12=
|
1000BASE-DWDM GBIC 1531.12 nm
|
12.2(33)SRA
|
DWDM-GBIC-30.33=
|
1000BASE-DWDM GBIC 1530.33 nm
|
12.2(33)SRA
|
Power over Ethernet Daughtercards
Note•The Power over Ethernet (PoE) daughtercard "Power Required" values do not include the power drawn by phones.
•Refer to this publication for more information about POE:
http://www.cisco.com/en/US/products/hw/switches/ps708/products_white_paper0900aecd80233a77.shtml
10/100/1000 Ethernet Switching Modules
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-X6748-GE-TX
|
7.00 A@42 V
|
48-port 10/100/1000 RJ-45
•CEF720 with WS-X6700-CFC (adds 0.75 A@42 V)
•dCEF720 with WS-F6700-DFC3BXL (adds 3.30 A@42 V)
•dCEF720 with WS-F6700-DFC3B (adds 3.00 A@42 V)
•Supports egress multicast replication
•QoS architecture:
–With DFC3: 2q8t/1p3q8t
–With CFC: 1q8t/1p3q8t
•Number of ports: 48
Number of port groups: 4
Port ranges per port group: 1-12, 13-24, 25-36, 37-48
|
| |
Supported only with Supervisor Engine 720
|
12.2(33)SRA
|
Note
•WS-X6748-GE-TX requires one of the following:
–WS-F6700-DFC3BXL (3.30 A@42 V)
–WS-F6700-DFC3B (3.00 A@42 V)
–WS-X6700-CFC (0.75 A@42 V)
•WS-X6748-GE-TX ships with WS-X6700-CFC installed unless ordered with WS-F6700-DFC3BXL or WS-F6700-DFC3B.
•WS-X6748-GE-TX is supported in the WS-C6503-E chassis.
•WS-X6748-GE-TX is not supported in the WS-C6503 and CISCO7603 chassis.
•In a 13-slot chassis, WS-X6748-GE-TX is supported only in slots 9 through 13 and does not power up in other slots.
•On WS-X6748-GE-TX ports, STP BPDUs are not exempt from Traffic Storm Control suppression. Do not configure Traffic Storm Control on STP-protected WS-X6748-GE-TX ports that interconnect network devices.
|
WS-X6548-GE-TX
|
2.98 A@42 V
|
48-port 10/100/1000 Mbps
•RJ-45
•CEF256
•WS-X6548-GE-TX supports WS-F6K-VPWR-GE and WS-F6K-GE48-AF
•WS-X6548V-GE-TX supports WS-F6K-VPWR-GE
•WS-X6548-GE-45AF has WS-F6K-GE48-AF
•QoS port architecture (Rx/Tx): 1q2t/1p2q2t
Number of ports: 48
Number of port groups: 2
Port ranges per port group: 1-24, 25-48
|
WS-X6548V-GE-TX
|
3.40 A@42 V
|
WS-X6548-GE-45AF
|
3.16 A@42 V
|
| |
With Supervisor Engine 720
(except WS-F6K-GE48-AF)
|
12.2(33)SRA
|
WS-F6K-GE48-AF with Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
WS-F6K-GE48-AF with Supervisor Engine 32
|
12.2(33)SRA
|
Note
•More than 1 Gbps of traffic per EtherChannel is supported on the WS-X6548-GE-TX (and voice-power daughtercard-equipped) switching modules.
•WS-X6548-GE-TX and WS-X6548V-GE-TX do not support these features:
–ISL trunking
–Jumbo frames
–802.1Q tunneling
–Traffic storm control
|
WS-X6148A-GE-TX
|
2.50 A@42 V
|
48-port 10/100/1000 Mbps
•RJ-45
•WS-X6148A-GE-TX supports WS-F6K-GE48-AF
•WS-X6148A-GE-45AF has WS-F6K-GE48-AF
•QoS port architecture (Rx/Tx): 1q2t/1p2q2t
•Number of ports: 48
Number of port groups: 2
Port ranges per port group: 1-24, 25-48
|
|
WS-X6148-GE-45AF
|
2.68 A@42 V
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
| |
With Supervisor Engine 32
|
12.2(33)SRA
|
Note WS-X6148A-GE-TX and WS-X6148A-GE-45AF do not support these features:
•More than 1 Gbps of traffic per EtherChannel
•WS-F6K-DFC3B, or WS-F6K-DFC3BXL
•ISL trunking
•Traffic storm control
|
WS-X6148-GE-TX
|
2.47 A@42 V
|
48-port 10/100/1000 Mbps
|
WS-X6148V-GE-TX
|
2.89 A@42 V
|
•RJ-45
|
WS-X6148-GE-45AF
|
2.65 A@42 V
|
•WS-X6148-GE-TX supports WS-F6K-VPWR-GE and WS-F6K-GE48-AF
|
| |
•WS-X6148V-GE-TX has WS-F6K-VPWR-GE
•WS-X6148-GE-45AF has WS-F6K-GE48-AF
•QoS port architecture (Rx/Tx): 1q2t/1p2q2t
•Number of ports: 48
Number of port groups: 2
Port ranges per port group: 1-24, 25-48
|
|
With Supervisor Engine 720
(except WS-F6K-GE48-AF)
|
12.2(33)SRA
|
WS-F6K-GE48-AF with Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
WS-F6K-GE48-AF with Supervisor Engine 32
|
12.2(33)SRA
|
Note WS-X6148-GE-TX, WS-X6148V-GE-TX, and WS-X6148-GE-45AF do not support these features:
•More than 1 Gbps of traffic per EtherChannel
•WS-F6K-DFC3B, or WS-F6K-DFC3BXL
•ISL trunking
•Jumbo frames
•802.1Q tunneling
•Traffic storm control
|
WS-X6516-GE-TX
|
3.45 A@42 V
|
16-port 10/100/1000BASE-T
•CEF256
•With Supervisor Engine 720:
–dCEF256 with WS-F6K-DFC3BXL (adds 1.47 A@42 V)
–dCEF256 with WS-F6K-DFC3B (adds 1.67 A@42 V)
•QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t
•Number of ports: 16
Number of port groups: 2
Port ranges per port group: 1-8, 9-16
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
Fast Ethernet Switching Modules
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-X6148-FE-SFP
|
2.30 A@42 V
|
48-port 100BASE-FX
•Requires Fast Ethernet SFPs
•QoS port architecture (Rx/Tx): 1p1q4t/1p3q8t
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
WS-X6524-100FX-MM
|
1.90 A@42 V
|
24-port 100FX Ethernet multimode
•CEF256
•With Supervisor Engine 720:
–dCEF256 with WS-F6K-DFC3BXL (adds 1.47 A@42 V)
–dCEF256 with WS-F6K-DFC3B (adds 1.67 A@42 V)
•QoS port architecture (Rx/Tx): 1p1q0t/1p3q1t
•Number of ports: 24
Number of port groups: 1
Port ranges per port group: 1-24
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
WS-X6324-100FX-SM
|
1.52 A@42 V
|
24-port 100FX Ethernet
|
WS-X6324-100FX-MM
|
1.52 A@42 V
|
•Single-mode and multimode MT-RJ
•128-KB per-port packet buffers
•QoS port architecture (Rx/Tx): 1q4t/2q2t
•Number of ports: 24
Number of port groups: 2
Port ranges per port group: 1-12, 13-24
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
WS-X6224-100FX-MT
|
1.90 A@42 V
|
24-port 100FX Ethernet Multimode MT-RJ
•QoS port architecture (Rx/Tx): 1q4t/2q2t
•Number of ports: 24
Number of port groups: 2
Port ranges per port group: 1-12, 13-24
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
Ethernet/Fast Ethernet (10/100) Switching Modules
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-X6548-RJ-45
|
2.90 A@42 V
|
48-port 10/100TX RJ-45
•CEF256
•With Supervisor Engine 720:
–dCEF256 with WS-F6K-DFC3BXL (adds 1.47 A@42 V)
–dCEF256 with WS-F6K-DFC3B (adds 1.67 A@42 V)
•QoS port architecture (Rx/Tx): 1p1q0t/1p3q1t
•Number of ports: 48
Number of port groups: 1
Port ranges per port group: 1-48
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
WS-X6548-RJ-21
|
2.90 A@42 V
|
48-port 10/100TX RJ-21
•CEF256
•With Supervisor Engine 720:
–dCEF256 with WS-F6K-DFC3BXL (adds 1.47 A@42 V)
–dCEF256 with WS-F6K-DFC3B (adds 1.67 A@42 V)
•QoS port architecture (Rx/Tx): 1p1q0t/1p3q1t
•Number of ports: 48
Number of port groups: 1
Port ranges per port group: 1-48
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
WS-X6148X2-RJ-45
|
2.65 A@42 V
|
96-port 10/100TX RJ-45
|
|
WS-X6148X2-45AF
|
2.92 A@42 V
|
•QoS port architecture (Rx/Tx): 1p1q0t/1p3q1t
•WS-X6148X2-RJ-45 supports WS-F6K-FE48X2-AF
•WS-X6148X2-45AF has WS-F6K-FE48X2-AF
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
WS-X6196-RJ-21
|
2.74 A@42 V
|
96-port 10/100TX RJ-21
|
|
WS-X6196-21AF
|
3.16 A@42 V
|
•QoS port architecture (Rx/Tx): 1p1q0t/1p3q1t
|
|
| |
•WS-X6196-RJ-21 supports WS-F6K-FE48X2-AF
|
|
•WS-X6196-21AF has WS-F6K-FE48X2-AF
|
|
With Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
WS-X6348-RJ-45
|
2.39 A@42 V
|
48-port 10/100TX RJ-45
|
WS-X6348-RJ-45V
|
2.39 A@42 V
|
•128-KB per-port packet buffers
|
| |
•QoS port architecture (Rx/Tx): 1q4t/2q2t
|
•WS-X6348-RJ-45 supports WS-F6K-VPWR
|
•WS-X6348-RJ-45V has WS-F6K-VPWR
|
•Number of ports: 48
Number of port groups: 4
Port ranges per port group: 1-12, 13-24, 25-36, 37-48
|
With Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
WS-X6348-RJ-21V
|
2.39 A@42 V
|
48-port 10/100TX RJ-21
•128-KB per-port packet buffers
•QoS port architecture (Rx/Tx): 1q4t/2q2t
•Has WS-F6K-VPWR
•Number of ports: 48
Number of port groups: 4
Port ranges per port group: 1-12, 13-24, 25-36, 37-48
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
WS-X6248-RJ-45
|
2.69 A@42 V
|
48-port 10/100TX RJ-45
•QoS port architecture (Rx/Tx): 1q4t/2q2t
•Number of ports: 48
Number of port groups: 4
Port ranges per port group: 1-12, 13-24, 25-36, 37-48
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
WS-X6248A-TEL
|
2.69 A@42 V
|
48-port 10/100TX RJ-21
•128-KB per-port packet buffers
•QoS port architecture (Rx/Tx): 1q4t/2q2t
•Number of ports: 48
Number of port groups: 4
Port ranges per port group: 1-12, 13-24, 25-36, 37-48
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
| |
|
With Supervisor Engine 32
|
12.2(33)SRA
|
WS-X6248-TEL
|
2.69 A@42 V
|
48-port 10/100TX RJ-21
•QoS port architecture (Rx/Tx): 1q4t/2q2t
•Number of ports: 48
Number of port groups: 4
Port ranges per port group: 1-12, 13-24, 25-36, 37-48
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
WS-X6148A-RJ-45
WS-X6148A-45AF
|
2.39 A@42 V
2.57 A@42 V
|
48-port 10/100TX RJ-45
•128-KB per-port packet buffers
•QoS port architecture (Rx/Tx): 1q4t/2q2t
•WS-X6148A-RJ-45 supports WS-F6K-GE48-AF
•WS-X6148A-45AF has WS-F6K-GE48-AF
•Number of ports: 48
Number of port groups: 4
Port ranges per port group: 1-12, 13-24, 25-36, 37-48
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
WS-X6148-RJ-45
|
2.39 A@42 V
|
48-port 10/100TX RJ-45
|
WS-X6148-RJ-45V
|
2.39 A@42 V
|
128-KB per-port packet buffers
|
WS-X6148-45AF
|
2.57 A@42 V
|
QoS port architecture (Rx/Tx): 1q4t/2q2t
•WS-X6148-RJ-45 supports WS-F6K-VPWR and WS-F6K-GE48-AF
•WS-X6148-RJ-45V has WS-F6K-VPWR
•WS-X6148-45AF has WS-F6K-GE48-AF
•Number of ports: 48
Number of port groups: 4
Port ranges per port group: 1-12, 13-24, 25-36, 37-48
|
| |
With Supervisor Engine 720
(except with WS-F6K-GE48-AF)
|
12.2(33)SRA
|
WS-F6K-GE48-AF with Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
WS-F6K-GE48-AF with Supervisor Engine 32
|
12.2(33)SRA
|
WS-X6148-RJ-21
|
2.39 A@42 V
|
48-port 10/100TX RJ-21
|
WS-X6148-RJ-21V
|
2.39 A@42 V
|
•128-KB per-port packet buffers
|
WS-X6148-21AF
|
2.57 A@42 V
|
•QoS port architecture (Rx/Tx): 1q4t/2q2t
•WS-X6148-RJ-21 supports WS-F6K-VPWR and WS-F6K-GE48-AF
•WS-X6148-RJ-21V has WS-F6K-VPWR
•WS-X6148-21AF has WS-F6K-GE48-AF
•Number of ports: 48
Number of port groups: 4
Port ranges per port group: 1-12, 13-24, 25-36, 37-48
|
| |
With Supervisor Engine 720
(except WS-F6K-GE48-AF)
|
12.2(33)SRA
|
WS-F6K-GE48-AF with Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
WS-F6K-GE48-AF with Supervisor Engine 32
|
12.2(33)SRA
|
Ethernet Switching Modules
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-X6024-10FL-MT
|
1.52 A@42 V
|
24-port 10BASE-FL MT-RJ
•QoS port architecture (Rx/Tx): 1q4t/2q2t
•Number of ports: 24
Number of port groups: 2
Port ranges per port group: 1-12, 13-24
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
Optical Services Modules (OSMs)
•OSM Guidelines and Restrictions
•Gigabit Ethernet WAN
•OC-48 Packet over SONET
•OC-48 DPT/Packet over SONET
•OC-12 Packet over SONET
•OC-3 Packet over SONET
•OC-12 Channelized
•CT3/T1 Channelized/Unchannelized
•OC-12 ATM
Note From 12.2(33) SRE onwards, OSMs are not supported on 7600 routers. For more information on EOS, refer http://www.cisco.com/en/US/products/hw/routers/ps368/prod_eol_notice0900aecd8073fdf9.html
OSM Guidelines and Restrictions
•Supervisor Engine 32 does not support OSMs.
•OSMs require a minimum of 256 MB of synchronous dynamic random-access memory (SDRAM) —Refer to this publication for memory upgrade procedures:
http://www.cisco.com/univercd/cc/td/doc/product/core/cis7600/hardware/osmodule/app_upgr.htm
•OSMs are CEF256 modules.
•OSM WAN port numbering starts with 1.
•On OSMs with Gigabit Ethernet GBIC Layer 2 LAN ports:
–OSM LAN port numbering starts with 1.
–The LAN ports are in a single port group.
•The OSM-2+4GE-WAN+ and the OC-12 Packet-over-SONET OSMs have been tested with the service modules and WS-SUP720.
•OSMs are not supported in the Cisco 7604 or in any S-series chassis.
Gigabit Ethernet WAN
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
OSM-2+4GE-WAN+
|
5.08 A@42 V
|
4-port Gigabit Ethernet WAN (GBIC) with two Layer 2 LAN ports; CEF256
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
OC-48 Packet over SONET
Note Also has four Layer 2 LAN ports.
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
OSM-1OC48-POS-SI+
OSM-1OC48-POS-SL+
OSM-1OC48-POS-SS+
|
3.90 A@42 V
|
Enhanced 1-port OC-48/STM-16 SONET/SDH OSM, SM-IR; CEF256
Enhanced 1-port OC-48/STM-16 SONET/SDH OSM, SM-LR; CEF256
Enhanced 1-port OC-48/STM-16 SONET/SDH OSM, SM-SR; CEF256
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
OC-48 DPT/Packet over SONET
Note Also has four Layer 2 LAN ports.
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
OSM-2OC48/1DPT-SS
OSM-2OC48/1DPT-SI
OSM-2OC48/1DPT-SL
|
5.75 A@42 V
|
2-port OC-48 DPT/POS, SM-SR; CEF256
2-port OC-48 DPT/POS, SM-IR; CEF256
2-port OC-48 DPT/POS, SM-LR; CEF256
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
OC-12 Packet over SONET
Note Also has four Layer 2 LAN ports.
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
OSM-4OC12-POS-SI+
|
4.55 A@42 V
|
Enhanced 4-port OC-12c/STM-4c POS, SM-IR; CEF256
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
OSM-2OC12-POS-SI+
|
3.36 A@42 V
|
Enhanced 2-port OC-12c/STM-4c POS, SM-IR; CEF256
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
OC-3 Packet over SONET
Note Also has four Layer 2 LAN ports.
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
OSM-16OC3-POS-SI+
|
4.80 A@42 V
|
Enhanced 16-port OC-3c/STM-1c POS, SM-IR; CEF256
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
OSM-8OC3-POS-SI+
OSM-8OC3-POS-SL+
|
3.57 A@42 V
|
Enhanced 8-port OC-3c/STM-1c POS, SM-IR; CEF256
Enhanced 8-port OC-3c/STM-1c POS, SM-LR; CEF256
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
OSM-4OC3-POS-SI+
|
2.44 A@42 V
|
Enhanced 4-port OC-3c/STM-1c POS, SM-IR; CEF256
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
OC-12 Channelized
Note Also has four Layer 2 LAN ports.
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
OSM-1CHOC12/T3-SI
OSM-1CHOC12/T1-SI
|
4.40 A@42 V
2.80 A@42 V
|
1-port channelized OC-12, SM-IR; CEF256
1-port channelized OC-12, SM-IR; CEF256
|
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
CT3/T1 Channelized/Unchannelized
Note OSM-12CT3/T1 has mini-SMB connectors for use with 75-ohm copper coaxial cable.
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
OSM-12CT3/T1
|
2.80 A@42 V
|
12-port channelized/unchannelized CT3/T1; CEF256
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
OC-12 ATM
Note Also has four Layer 2 LAN ports.
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
OSM-2OC12-ATM-MM+
OSM-2OC12-ATM-SI+
|
4.00 A@42 V
|
Enhanced 2-port OC-12/STM-4 ATM OSM, MM; CEF256
Enhanced 2-port OC-12/STM-4 ATM OSM, SM-IR; CEF256
|
| |
With Supervisor Engine 720
|
12.2(33)SRA
|
SPA Interface Processors (SIPs)
Note See the Release Notes for Cisco IOS Release 12.2SR on the Cisco 7600 Series Routers for information about additional procedures required to support SIPs with Cisco IOS Release 12.2(33)SRA and later releases.
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
7600-SIP-600
|
8.14 A@42 V
|
SPA Interface Processor-600
|
Supported only with Supervisor Engine 720
|
12.2(33)SRA
|
Note Supervisor Engine 32 does not support 7600-SIP-600.
|
7600-SIP-400
|
6.31 A@42 V
|
SPA Interface Processor-400
|
With Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
Note For release 12.2(33)SRB, oversubscription is supported.
|
7600-SIP-200
|
5.72 A@42 V
|
SPA Interface Processor-200
|
With Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
SIP-400 Combinations
The SIP-400 linecard supports an aggregate forwarding rate of approximately 6 Mpps. Packet forwarding is done by microcode on the network processors so enabling datapath features may reduce performance.
For release 12.2(33)SRA, the total supported bandwidth for the SIP-400 is 4 Gigabits line rate for Ethernet and 2.5 Gigabits line rate for SONET with selected services. There is no oversubscription support. The product ordering tools would prevent combination of SPAs that add up to more than this bandwidth and would reject such configurations.
For release 12.2(33)SRB and above, the following SPA combinations are supported on SIP-400:
•Any mix of POS, ATM, CEoP and serial SPAs up to an aggregate of OC-48
•One SPA-2X1GE SPA plus POS, ATM, CEoP, or Serial SPAs up to an aggregate of OC-24
•Two SPA-2X1GE SPAs
•Two SPA-5X1GE-V2 SPAs (oversubscribed)
•One SPA-1X10GE-L-V2 SPA (oversubscribed)
For release 12.2(33)SRD and above, the following SPA combinations are supported on SIP-400:
•Four SPA-4X1FE-TX-V2
•Two SPA-8X1FE-TX-V2
Refer to Shared Port Adapters (SPAs) for the minimum release required to support each SPA type.
Shared Port Adapters (SPAs)
These sections describe SPAs:
•Ethernet SPAs
•POS SPAs
•ATM SPAs
•Serial SPAs
•Circuit Emulation over Packet (CEoP) SPAs
Ethernet SPAs
These sections describe Ethernet SPAs:
•Ten Gigabit Ethernet SPAs
•Gigabit Ethernet SPAs
•Fast Ethernet SPAs
Ten Gigabit Ethernet SPAs
Product ID
(append "=" for spares)
|
SIP Support
|
Product Description
|
Minimum Software Version
|
SPA-1XTENGE-XFP
|
7600-SIP-600
|
1-port 10 Gigabit Ethernet SPA, LANPHY XFP Optics
|
12.2(33)SRA
|
SPA-1XTENGE-XFP-V2
|
7600-SIP-600
|
1-port 10 Gigabit Ethernet SPA, LANPHY XFP Optics
|
12.2(33)SRA
|
SPA-1X10GE-L-V2
|
7600-SIP-600
|
1-port 10 Gigabit Ethernet SPA, SFP Optics
|
12.2(33)SRA
|
SPA-1X10GE-L-V2
|
7600-SIP-400
|
1-port 10 Gigabit Ethernet SPA, SFP Optics
|
12.2(33)SRC
|
| |
XFP Modules Supported in SPA-1XTENGE-XFP
|
| |
XFP-10GLR-OC192SR
|
12.2(33)SRA
|
| |
|
XFP-10GER-OC192IR
|
12.2(33)SRA
|
| |
|
XFP-10GZR-OC192LR
|
12.2(33)SRA
|
| |
|
XFP modules supported in SPA-1X10GE-L-V2 on SIP-400.
|
| |
|
XFP-10GER-OC192IR+=
|
12.2(33)SRD
|
| |
|
DWDM-XFP modules supported in SPA-1X10GE-L-V2 on SIP-600.
|
| |
|
DWDM-XFP-30.33=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-31.12=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-31.90=
|
12.2(33)SRB3
|
| |
|
DWDM- XFP-32.68=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-34.25=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-35.04=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-35.82=
|
12.2(33)SRB3
|
| |
|
DWDM- XFP-36.61=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-38.19=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-38.98=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-39.77=
|
12.2(33)SRB3
|
| |
|
DWDM- XFP-40.56=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-42.14=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-42.94=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-43.73=
|
12.2(33)SRB3
|
| |
|
DWDM- XFP-44.53=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-46.12=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-46.92=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-47.72=
|
12.2(33)SRB3
|
| |
|
DWDM- XFP-48.51=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-50.12=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-50.92=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-51.72=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-52.52=
|
12.2(33)SRB3
|
| |
|
DWDM- XFP-54.13=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-54.94=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-55.75=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-56.55=
|
12.2(33)SRB3
|
| |
|
DWDM- XFP-58.17=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-58.98=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-59.79=
|
12.2(33)SRB3
|
| |
|
DWDM- XFP-60.61=
|
12.2(33)SRB3
|
Gigabit Ethernet SPAs
Product ID
(append "=" for spares)
|
SIP Support
|
Product Description
|
Minimum Software Version
|
SPA-10X1GE
|
7600-SIP-600
|
10-port Gigabit Ethernet SPA, SFP Optics
|
12.2(33)SRA
|
SPA-10X1GE-V2
|
7600-SIP-600
|
10-port Gigabit Ethernet SPA, SFP Optics
|
12.2(33)SRA
|
SPA-5X1GE
|
7600-SIP-600
|
5-port Gigabit Ethernet SPA, SFP Optics
|
12.2(33)SRA
|
SPA-5X1GE-V2
|
7600-SIP-600
|
5-port Gigabit Ethernet SPA, SFP Optics
|
12.2(33)SRA
|
SPA-5X1GE-V2
|
7600-SIP-400
|
5-port Gigabit Ethernet SPA, SFP Optics
|
12.2(33)SRB
|
SPA-2X1GE
|
7600-SIP-400
|
2-port Gigabit Ethernet SPA, SFP Optics
|
12.2(33)SRA
|
SPA-2X1GE-V2
|
7600-SIP-400
|
2-port Gigabit Ethernet SPA, SFP Optics
|
12.2(33)SRB
|
| |
SFPs Supported in Gigabit Ethernet SPAs, SIP 400, SIP 600, ES-20, ES+, ES+combo, SUP32, WS-6724, and WS-X6748.
Note Sup32/6724/6748 cannot support DWDM-SFP-3346/3739/4134/4532/4931/5332/5736/6141 in SRE.
|
| |
|
GLC-BX-D
|
12.2(33)SRD
|
| |
|
GLC-BX-U
|
12.2(33)SRD
|
| |
SFP-GE-S
|
12.2(33)SRA
|
|
SFP-GE-L
|
12.2(33)SRA
|
|
SFP-GE-Z
|
12.2(33)SRA
|
| |
|
SFP-GE-T
|
12.2(33)SRB3
|
| |
|
CWDM-SFP-1470=
|
12.2(33)SRD
|
| |
|
CWDM-SFP-1490=
|
12.2(33)SRD
|
| |
|
CWDM-SFP-1510=
|
12.2(33)SRD
|
| |
|
CWDM-SFP-1530=
|
12.2(33)SRD
|
| |
|
CWDM-SFP-1550=
|
12.2(33)SRD
|
| |
|
CWDM-SFP-1570=
|
12.2(33)SRD
|
| |
|
CWDM-SFP-1590=
|
12.2(33)SRD
|
| |
|
CWDM-SFP-1610=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3033=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3112=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3190=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3268=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3425=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3504=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3582=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3661=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3819=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3898=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3977=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4056=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4214=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4294=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4373=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4453=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4612=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4692=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4772=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4851=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5012=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5092=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5172=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5252=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5413=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5494=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5575=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5655=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5817=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5898=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5979=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-6061=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3346=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-3739=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-4134=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-4532=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-4931=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-5332=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-5736=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-6141=
|
12.2(33)SRE
|
Fast Ethernet SPAs
Product ID
(append "=" for spares)
|
SIP Support
|
Product Description
|
Minimum Software Version
|
SPA-4X1FE-TX-V2
|
7600-SIP-400
|
4-port 10/100 Ethernet SPA TX
|
12.2(33)SRD
|
SPA-8X1FE-TX-V2
|
7600-SIP-400
|
8-port 10/100 Ethernet SPA TX
|
12.2(33)SRD
|
SPA-4X1FE-TX-V2
|
7600-SIP-200
|
4-port 10/100 Ethernet SPA TX
|
12.2(33)SRA
|
SPA-8X1FE-TX-V2
|
7600-SIP-200
|
8-port 10/100 Ethernet SPA TX
|
12.2(33)SRA
|
POS SPAs
Product ID
(append "=" for spares)
|
SIP Support
|
Product Description
|
Minimum Software Version
|
SPA-2XOC3-POS
|
7600-SIP-200
7600-SIP-400
|
2-port OC-3c/STM-1c POS SPA
|
12.2(33)SRA
|
| |
SFP Modules Supported in SPA-2XOC3-POS
|
| |
SFP-OC3-MM
|
12.2(33)SRA
|
| |
SFP-OC3-SR
|
12.2(33)SRA
|
| |
SFP-OC3-IR1
|
12.2(33)SRA
|
| |
SFP-OC3-LR1
|
12.2(33)SRA
|
| |
SFP-OC3-LR2
|
12.2(33)SRA
|
SPA-4XOC3-POS
|
7600-SIP-200
7600-SIP-400
|
4-port OC-3c/STM-1c POS SPA
|
12.2(33)SRA
|
| |
SFP Modules Supported in SPA-4XOC3-POS SPAs
|
| |
SFP-OC3-MM
|
12.2(33)SRA
|
| |
SFP-OC3-SR
|
12.2(33)SRA
|
| |
SFP-OC3-IR1
|
12.2(33)SRA
|
| |
SFP-OC3-LR1
|
12.2(33)SRA
|
| |
SFP-OC3-LR2
|
12.2(33)SRA
|
SPA-1XOC12-POS
|
7600-SIP-400
|
1-port OC-12c/STM-4c POS SPA
|
12.2(33)SRA
|
| |
SFP Modules Supported in SPA-1XOC12-POS SPA
|
| |
SFP-OC12-MM
|
12.2(33)SRA
|
| |
SFP-OC12-SR
|
12.2(33)SRA
|
| |
SFP-OC12-IR1
|
12.2(33)SRA
|
| |
SFP-OC12-LR1
|
12.2(33)SRA
|
| |
SFP-OC12-LR2
|
12.2(33)SRA
|
SPA-OC192POS-LR
|
7600-SIP-600
|
1-port OC-192c/STM-64 POS/RPR SPA, SM-LR
|
12.2(33)SRA
|
SPA-OC192POS-XFP
|
7600-SIP-600
|
1-port OC-192c/STM-64 POS/RPR SPA, XFP Optics
|
12.2(33)SRA
|
| |
XFP Modules Supported in SPA-OC192POS-XFP SPA
|
| |
XFP-10GLR-OC192SR
|
12.2(33)SRA
|
| |
XFP-10GER-OC192IR
|
12.2(33)SRA
|
| |
|
XFP-10GZR-OC192LR
|
12.2(33)SRB1
|
SPA-1XOC48POS/RPR
|
7600-SIP-400
|
1-port OC-48c/STM-16 SPA
|
12.2(33)SRA
|
| |
SFP Modules Supported in SPA-1XOC48POS/RPR SPA
|
| |
SFP-OC48-SR
|
12.2(33)SRA
|
| |
SFP-OC48-IR1
|
12.2(33)SRA
|
| |
SFP-OC48-LR2
|
12.2(33)SRA
|
SPA-2XOC48POS/RPR
|
7600-SIP-600
|
2 port OC-48 POS/RPR SPA with SFP Optics
|
12.2(33)SRA
|
| |
SFP Modules Supported in SPA-2XOC48POS/RPR SPA
|
| |
SFP-OC48-SR
|
12.2(33)SRA
|
| |
SFP-OC48-IR1
|
12.2(33)SRA
|
| |
SFP-OC48-LR2
|
12.2(33)SRA
|
SPA-4XOC48POS/RPR
|
7600-SIP-600
|
4-port OC-48c/STM-16 POS/DPT/RPR SPA
|
12.2(33)SRA
|
| |
SFP Modules Supported in SPA-4XOC48POS/RPR
|
| |
SFP-OC48-SR
|
12.2(33)SRA
|
| |
SFP-OC48-IR1
|
12.2(33)SRA
|
| |
SFP-OC48-LR2
|
12.2(33)SRA
|
ATM SPAs
Product ID
(append "=" for spares)
|
SIP Support
|
Product Description
|
Minimum Software Version
|
SPA-2XOC3-ATM
|
7600-SIP-200
7600-SIP-400
|
2-port OC-3c/STM-1c ATM SPA
|
12.2(33)SRA
|
| |
SFP Modules Supported in SPA-2XOC3-ATM
|
| |
SFP-OC3-MM
|
12.2(33)SRA
|
| |
SFP-OC3-IR1
|
12.2(33)SRA
|
| |
SFP-OC3-LR1
|
12.2(33)SRA
|
| |
SFP-OC3-LR2
|
12.2(33)SRA
|
SPA-4XOC3-ATM
|
7600-SIP-200
7600-SIP-400
|
4-port OC-3c/STM-1c ATM SPA
|
12.2(33)SRA
|
| |
SFP Modules Supported in SPA-4XOC3-ATM
|
| |
SFP-OC3-MM
|
12.2(33)SRA
|
| |
SFP-OC3-IR1
|
12.2(33)SRA
|
| |
SFP-OC3-LR1
|
12.2(33)SRA
|
| |
SFP-OC3-LR2
|
12.2(33)SRA
|
SPA-1XOC12-ATM
|
7600-SIP-400
|
1-Port OC-12c/STM-4c ATM SPA
|
12.2(33)SRA
|
| |
SFP Modules Supported in SPA-1XOC12-ATM SPA
|
|
| |
SFP-OC12-MM
|
12.2(33)SRA
|
| |
SFP-OC12-SR
|
12.2(33)SRA
|
| |
SFP-OC12-IR1
|
12.2(33)SRA
|
| |
SFP-OC12-LR1
|
12.2(33)SRA
|
| |
SFP-OC12-LR2
|
12.2(33)SRA
|
SPA-1XOC48-ATM
|
7600-SIP-400
|
1 port OC-48c/STM-16 ATM SPA
|
12.2(33)SRA
|
Serial SPAs
Product ID
(append "=" for spares)
|
SIP Support
|
Product Description
|
Minimum Software Version
|
SPA-8XCHT1/E1
|
7600-SIP-200
|
8-Port Channelized T1/E1 SPA
|
12.2(33)SRA
|
| |
7600-SIP-400
|
|
12.2(33)SRC
|
SPA-2XT3/E3
|
7600-SIP-200
|
2-port Clear Channel T3/E3 SPA
|
12.2(33)SRA
|
| |
7600-SIP-400
|
|
12.2(33)SRC
|
SPA-4XT3/E3
|
7600-SIP-200
|
4-port Clear Channel T3/E3 SPA
|
12.2(33)SRA
|
| |
7600-SIP-400
|
|
12.2(33)SRC
|
SPA-2XCT3/DS0
|
7600-SIP-200
|
2-port Channelized T3 to DS0 SPA
|
12.2(33)SRA
|
| |
7600-SIP-400
|
|
12.2(33)SRC
|
SPA-4XCT3/DS0
|
7600-SIP-200
|
4-port Channelized T3 to DS0 SPA
|
12.2(33)SRA
|
| |
7600-SIP-400
|
|
12.2(33)SRC
|
SPA-1XCHSTM1/OC3
|
7600-SIP-200
|
1-port Channelized STM1/OC3 to DS0 SPA
|
12.2(33)SRA
|
| |
7600-SIP-400
|
|
12.2(33)SRC
|
| |
|
SFP Modules Supported in SPA-1XCHSTM1/OC3 on 7600-SIP-400
|
|
| |
|
ONS-SC-155-EL
|
12.2(33)SRD2
|
SPA-4XT-Serial SPA
|
7600-SIP-200
|
4-Port Serial Interface SPA
|
12.2(33)SRC1
|
Circuit Emulation over Packet (CEoP) SPAs
Product ID
(append "=" for spares)
|
SIP Support
|
Product Description
|
Minimum Software Version
|
SPA-2CHT3-CE-ATM
|
7600-SIP-400
|
2-Port Channelized T3/E3 ATM CEoP SPA
|
12.2(33)SRC
|
Note The SPA-2CHT3-CE-ATM does not use SFPs, use a Telco connector with a Y cable to connect to a patch panel.
|
SPA-1CHOC3-CE-ATM
|
7600-SIP-400
|
1-Port Channelized OC-3 STM1 ATM CEoP SPA
|
12.2(33)SRB
|
| |
SFP Modules Supported in SPA-1XCHOC3-CE
|
| |
SFP-OC3-MM
|
12.2(33)SRB
|
| |
SFP-OC3-IR1
|
12.2(33)SRB
|
| |
SFP-OC3-LR1
|
12.2(33)SRB
|
| |
SFP-OC3-LR2
|
12.2(33)SRB
|
| |
|
SFP-OC3-SR
|
12.2(33)SRB
|
| |
|
ONS-SC-155-EL
|
12.2(33)SRD2
|
SPA-24CHT1-CE-ATM
|
7600-SIP-400
|
24-Port Channelized T1/E1/J1 ATM CEoP SPA
|
12.2(33)SRB
|
Note The SPA-24CHT1-CE-ATM does not use SFPs, use a Telco connector with a Y cable to connect to a patch panel.
|
Services SPA Carrier (SSC)
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
7600-SSC-400
|
5.43 A@42 V
|
Services SPA Carrier (SSC)
|
12.2(33)SRA
|
Note
•7600-SSC-400 does not maintain state when an NSF with SSO redundancy mode switchover occurs.
•Supervisor Engine 720 and Supervisor Engine 32 support the 7600-SSC-400 beginning with Cisco IOS Release 12.2(33)SRA .
•Route Switching Processor 720-1GE supports the 7600-SSC-400 beginning with Cisco IOS Release 12.2(33)SRC .
|
Services SPAs
Product ID
(append "=" for spares)
|
Carrier
|
Product Description
|
Minimum Software Version
|
IPSEC-SPA-2G
|
7600-SSC-400
|
IPSec SPA
|
12.2(33)SRA
|
Note The IPSEC-SPA-2G supports the Route Switching Processor 720 beginning with Cisco IOS Release 12.2(33)SRC.
|
Enhanced FlexWAN Module
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-X6582-2PA
|
2.50 A@42 V
|
Enhanced FlexWAN Module; CEF256
|
| |
|
With Supervisor Engine 720
|
12.2(33)SRA
|
| |
|
With Supervisor Engine 32
|
12.2(33)SRA
|
Note See the Release Notes for Cisco IOS Release 12.2SR on the Cisco 7600 Series Routers for information about additional procedures required to support WS-X6582-2PA with Cisco IOS Release 12.2(33)SRA and later releases.
|
Enhanced FlexWAN Module Port Adapters
Product ID
(append "=" for spares)
|
Product Description
|
Minimum Software Version
|
PA-2FE-TX, -FX
|
2-port Fast Ethernet port adapter (supported only in WS-X6582-2PA)
|
12.2(33)SRA
|
PA-1FE-TX, -FX
|
1-port Fast Ethernet port adapter (supported only in WS-X6582-2PA)
|
12.2(33)SRA
|
PA-POS-1OC3
|
1-port Packet over SONET OC3c/STM1 port adapter
|
12.2(33)SRA
|
PA-POS-2OC3
|
2-port POS OC3c/STM1 port adapter
|
12.2(33)SRA
|
SFPs for PA-POS-2OC3
|
SFP-OC3-MM
|
Short range, multimode fiber
|
12.2(33)SRA
|
SFP-OC3-IR1
|
Intermediate range, single-mode fiber
|
12.2(33)SRA
|
SFP-OC3-LR1
|
Long range, single-mode fiber
|
12.2(33)SRA
|
PA-A6-OC3MM
|
1-port ATM OC-3c/STM-1 multimode port adapter, enhanced
|
12.2(33)SRA
|
PA-A6-OC3SMI
|
1-port ATM OC-3c/STM-1 single-mode (IR) port adapter, enhanced
|
12.2(33)SRA
|
PA-A6-OC3SML
|
1-port ATM OC-3c/STM-1 single-mode (LR) port adapter, enhanced
|
12.2(33)SRA
|
PA-A6-T3
|
1-port ATM DS3 port adapter, enhanced
|
12.2(33)SRA
|
PA-A6-E3
|
1-port ATM E3 port adapter, enhanced
|
12.2(33)SRA
|
PA-POS-OC3MM
PA-POS-OC3SMI
PA-POS-OC3SML
|
Packet over SONET (OC-3) port adapters
|
12.2(33)SRA
|
PA-A3-OC3MM
PA-A3-OC3SMI
PA-A3-T3
PA-A3-OC3SML
PA-A3-E3
PA-A3-8T1IMA
PA-A3-8E1IMA
|
ATM with traffic shaping port adapters
|
12.2(33)SRA
|
PA-T3
PA-T3+
PA-2T3
PA-2T3+
PA-E3
PA-2E3
PA-MC-T3
PA-MC-E3
PA-MC-2T3+
|
T3/E3 (clear-channel and channelized) port adapters
|
12.2(33)SRA
|
PA-4T+
PA-8T-V35
PA-8T-X21
PA-8T-232
PA-MC-2E1/120
PA-MC-8T1
PA-MC-8E1/120
PA-MC-2T1
PA-MC-4T1
|
T1/E1 port adapters
|
12.2(33)SRA
|
PA-4E1G/75
PA-4E1G/120
|
T1/E1 port adapters
|
12.2(33)SRA
|
PA-MC-8TE1+
|
Multichannel T1/E1 8PRI port adapters
|
12.2(33)SRA
|
PA-H
PA-2H
|
HSSI port adapters
|
12.2(33)SRA
|
PA-MC-STM-1
|
Multichannel STM-1 port adapters
|
12.2(33)SRA
|
Ethernet Services 20G Line Cards
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
7600-ES20-GE3C
|
8.1 A@42 V
|
Cisco 7600 ES20 line card, 20xGE SFP with DFC 3C
|
|
| |
|
With Supervisor Engine 720
|
12.2(33)SRB
|
| |
|
With RSP 720
|
12.2(33)SRB
|
| |
|
SFPs Supported
|
|
| |
|
GLC-BX-D
|
12.2(33)SRD
|
| |
|
GLC-BX-U
|
12.2(33)SRD
|
| |
|
SFP-GE-S
|
12.2(33)SRB
|
| |
|
SFP-GE-L
|
12.2(33)SRB
|
| |
|
SFP-GE-Z
|
12.2(33)SRB
|
| |
|
SFP-GE-T
|
12.2(33)SRB3
|
| |
|
CWDM-SFP-1470=
|
12.2(33)SRB3
|
| |
|
CWDM-SFP-1490=
|
12.2(33)SRB3
|
| |
|
CWDM-SFP-1510=
|
12.2(33)SRB3
|
| |
|
CWDM-SFP-1530=
|
12.2(33)SRB3
|
| |
|
CWDM-SFP-1550=
|
12.2(33)SRB3
|
| |
|
CWDM-SFP-1570=
|
12.2(33)SRB3
|
| |
|
CWDM-SFP-1590=
|
12.2(33)SRB3
|
| |
|
CWDM-SFP-1610=
|
12.2(33)SRB3
|
| |
|
DWDM-SFP-3033=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3112=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3190=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3268=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3425=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3504=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3582=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3661=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3819=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3898=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3977=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4056=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4214=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4294=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4373=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4453=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4612=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4692=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4772=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4851=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5012=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5092=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5172=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5252=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5413=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5494=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5575=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5655=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5817=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5898=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5979=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-6061=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3346=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-3739=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-4134=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-4532=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-4931=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-5332=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-5736=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-6141=
|
12.2(33)SRE
|
7600-ES20-GE3CXL
|
8.1 A@42 V
|
Cisco 7600 ES20 line card, 20xGE SFP with DFC 3CXL
|
| |
With Supervisor Engine 720
|
12.2(33)SRB
|
| |
|
With RSP 720
|
12.2(33)SRB
|
| |
|
SFPs Supported
|
|
| |
|
GLC-BX-D
|
12.2(33)SRD
|
| |
|
GLC-BX-U
|
12.2(33)SRD
|
| |
|
SFP-GE-S
|
12.2(33)SRB
|
| |
|
SFP-GE-L
|
12.2(33)SRB
|
| |
|
SFP-GE-Z
|
12.2(33)SRB
|
| |
|
SFP-GE-T
|
12.2(33)SRB3
|
| |
|
CWDM-SFP-1470=
|
12.2(33)SRB3
|
| |
|
CWDM-SFP-1490=
|
12.2(33)SRB3
|
| |
|
CWDM-SFP-1510=
|
12.2(33)SRB3
|
| |
|
CWDM-SFP-1530=
|
12.2(33)SRB3
|
| |
|
CWDM-SFP-1550=
|
12.2(33)SRB3
|
| |
|
CWDM-SFP-1570=
|
12.2(33)SRB3
|
| |
|
CWDM-SFP-1590=
|
12.2(33)SRB3
|
| |
|
CWDM-SFP-1610=
|
12.2(33)SRB3
|
| |
|
DWDM-SFP-3033=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3112=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3190=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3268=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3425=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3504=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3582=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3661=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3819=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3898=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3977=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4056=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4214=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4294=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4373=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4453=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4612=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4692=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4772=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4851=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5012=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5092=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5172=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5252=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5413=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5494=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5575=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5655=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5817=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5898=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5979=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-6061
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3346=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-3739=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-4134=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-4532=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-4931=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-5332=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-5736=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-6141=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-3346=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-3739=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-4134=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-4532=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-4931=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-5332=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-5736=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-6141=
|
12.2(33)SRE
|
7600-ES20-10G3C
|
8.1 A@42 V
|
Cisco 7600 ES20 line card, 2x10GE XFP with DFC 3C
|
| |
With Supervisor Engine 720
|
12.2(33)SRB
|
| |
|
With RSP 720
|
12.2(33)SRB
|
| |
|
XFPs Supported
|
|
| |
|
XFP-10GER-192IR+=
|
12.2(33)SRD
|
| |
|
XFP-10GLR-OC192SR
|
12.2(33)SRB
|
| |
|
XFP-10GER-OC192IR
|
12.2(33)SRB
|
| |
|
XFP-10GZR-OC192LR
|
12.2(33)SRB1
|
| |
|
DWDM-XFP-30.33=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-31.12=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-31.90=
|
12.2(33)SRB3
|
| |
|
DWDM- XFP-32.68=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-34.25=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-35.04=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-35.82=
|
12.2(33)SRB3
|
| |
|
DWDM- XFP-36.61=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-38.19=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-38.98=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-39.77=
|
12.2(33)SRB3
|
| |
|
DWDM- XFP-40.56=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-42.14=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-42.94=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-43.73=
|
12.2(33)SRB3
|
| |
|
DWDM- XFP-44.53=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-46.12=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-46.92=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-47.72=
|
12.2(33)SRB3
|
| |
|
DWDM- XFP-48.51=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-50.12=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-50.92=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-51.72=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-52.52=
|
12.2(33)SRB3
|
| |
|
DWDM- XFP-54.13=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-54.94=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-55.75=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-56.55=
|
12.2(33)SRB3
|
| |
|
DWDM- XFP-58.17=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-58.98=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-59.79=
|
12.2(33)SRB3
|
| |
|
DWDM- XFP-60.61=
|
12.2(33)SRB3
|
7600-ES20-10G3CXL
|
8.1 A@42 V
|
Cisco 7600 ES20 line card, 2x10GE XFP with DFC 3CXL
|
|
| |
|
With Supervisor Engine 720
|
12.2(33)SRB
|
| |
|
With RSP 720
|
12.2(33)SRB
|
| |
|
XFPs Supported
|
|
| |
|
XFP-10GER-192IR+
|
12.2(33)SRD
|
| |
|
XFP-10GLR-OC192SR
|
12.2(33)SRB
|
| |
|
XFP-10GER-OC192IR+=
|
12.2(33)SRB
|
| |
|
XFP-10GZR-OC192LR
|
12.2(33)SRB1
|
| |
|
DWDM-XFP-30.33=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-31.12=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-31.90=
|
12.2(33)SRB3
|
| |
|
DWDM- XFP-32.68=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-34.25=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-35.04=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-35.82=
|
12.2(33)SRB3
|
| |
|
DWDM- XFP-36.61=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-38.19=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-38.98=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-39.77=
|
12.2(33)SRB3
|
| |
|
DWDM- XFP-40.56=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-42.14=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-42.94=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-43.73=
|
12.2(33)SRB3
|
| |
|
DWDM- XFP-44.53=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-46.12=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-46.92=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-47.72=
|
12.2(33)SRB3
|
| |
|
DWDM- XFP-48.51=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-50.12=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-50.92=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-51.72=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-52.52=
|
12.2(33)SRB3
|
| |
|
DWDM- XFP-54.13=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-54.94=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-55.75=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-56.55=
|
12.2(33)SRB3
|
| |
|
DWDM- XFP-58.17=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-58.98=
|
12.2(33)SRB3
|
| |
|
DWDM-XFP-59.79=
|
12.2(33)SRB3
|
| |
|
DWDM- XFP-60.61=
|
12.2(33)SRB3
|
Note The Ethernet Services 20G line cards support all Cisco 7600 series routers except for the Cisco 7603 router
|
Ethernet Services 40G Line Cards
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
7600-ES+20G3C
|
6.58 A @42 V
|
7600 ES+ Line Card, 20xGE SFP with DFC 3C
|
| |
|
| |
|
With Supervisor Engine 720
|
12.2(33)SRD
|
| |
|
With RSP 720
|
12.2(33)SRD
|
| |
|
SFPs Supported
|
|
| |
|
SFP-GE-S
|
12.2(33)SRD
|
| |
|
SFP-GE-L
|
12.2(33)SRD
|
| |
|
SFP-GE-Z
|
12.2(33)SRD
|
| |
|
SFP-GE-T
|
12.2(33)SRD
|
| |
|
GLC-BX-D
|
12.2(33)SRD
|
| |
|
GLC-BX-U
|
12.2(33)SRD
|
| |
|
CWDM-SFP-1470=
|
12.2(33)SRD
|
| |
|
CWDM-SFP-1490=
|
12.2(33)SRD
|
| |
|
CWDM-SFP-1510=
|
12.2(33)SRD
|
| |
|
CWDM-SFP-1530=
|
12.2(33)SRD
|
| |
|
CWDM-SFP-1550=
|
12.2(33)SRD
|
| |
|
CWDM-SFP-1570=
|
12.2(33)SRD
|
| |
|
CWDM-SFP-1590=
|
12.2(33)SRD
|
| |
|
CWDM-SFP-1610=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3033=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3112=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3190=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3268=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3425=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3504=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3582=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3661=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3819=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3898=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3977=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4056=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4214=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4294=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4373=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4453=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4612=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4692=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4772=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-4851=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5012=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5092=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5172=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5252=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5413=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5494=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5575=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5655=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5817=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5898=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-5979=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-6061=
|
12.2(33)SRD
|
| |
|
DWDM-SFP-3346=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-3739=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-4134=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-4532=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-4931=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-5332=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-5736=
|
12.2(33)SRE
|
| |
|
DWDM-SFP-6141=
|
12.2(33)SRE
|
7600-ES+20G3CXL
|
7.25A@42 V
|
7600 ES+ Line Card, 20xGE SFP with DFC 3CXL
|
| |
With Supervisor Engine 720
|
12.2(33)SRD
|
With RSP 720
|
12.2(33)SRD
|
| |
|
SFPs Supported
|
|
| |
|
SFP-GE-S
|
12.2(33)SRD
|
| |
|
SFP-GE-L
|
12.2(33)SRD
|
| |
|
SFP-GE-Z
|
12.2(33)SRD
|
| |
|
SFP-GE-T
|
12.2(33)SRD
|
| |
|
GLC-BX-D
|
12.2(33)SRD
|
| |
|
GLC-BX-U
|
12.2(33)SRD
|
| |
|
CWDM-SFP-1470=
|
12.2(33)SRD
|
| |
|
CWDM-SFP-1490=
|
12.2(33)SRD
|
| |
|
CWDM-SFP-1510=
|
12.2(33)SRD
|
| |
|
CWDM-SFP-1530=
|
12.2(33)SRD
|
| |
|
CWDM-SFP-1550=
|
12.2(33)SRD
|
| |
