Cisco 12000 Series Routers

Table Of Contents

Technical Specifications

Router Specifications

Technical Specifications

---

This appendix lists the Cisco 12010, Cisco 12410 and Cisco 12810 router specifications.

Router Specifications

The Cisco 12010, Cisco 12410, and Cisco 12810 series routers specifications are presented in four tables:

•Table A-1, "Physical Specifications"

•Table A-2, "AC Electrical Specifications"

•Table A-3, "DC Electrical Specifications"

•Table A-4, "Environmental Specifications"

Table A-1 Physical Specifications

Description	Value
Chassis height	37.5 in. (95.2 cm)
Chassis width	17.25 in. (43.8 cm) 19.0 in. (48.3 cm) including chassis rack-mount flanges and front door width
Chassis depth	22.0 in. (55.9 cm) 26.5 in (67.3 cm) including cable management system and front cover
Weight •chassis only •chassis: fully configured using all card slots and 2 AC input power supplies	125 lb (56.7 kg) 287 lb (130.2 kg)

Table A-2 AC Electrical Specifications

Description	Value
Power	2791 VA (volt-amps) per AC power supply (2 AC power supplies per system)—original series 3000 VA (volt-amps) per AC power supply (2 AC power supplies per system)—original series
Rated input voltage1	200-240 VAC nominal (range: 180 to 264 VAC) 220-240 VAC (UK)
Rated input line frequency1	50/60 Hz nominal (range: 47 to 63 Hz) 50/60 Hz UK
Input current rating1	15 A maximum @ 200 VAC 13 A maximum @220 to 240 VRMS (UK)
Source AC service requirement1	20 A North America; 16 A international; 13 A UK
Heat dissipation (total maximum)	2800 W@9,544 BTU/hour
Redundancy	2 AC power supply modules required for 2N redundancy

1 For each AC power supply module.

---

Caution To ensure that the chassis configuration complies with the required power budgets, use the on-line power calculator. Failure to properly verify the configuration may result in an unpredictable state if one of the power units fails. Contact your local sales representative for assistance.

---

Table A-3 DC Electrical Specifications

Description	Value
Power	2400 W per DC power entry module (original series) 2800 W per DC power entry module (enhanced series)
Rated input voltage1	-48 VDC nominal in North America -60 VDC nominal in the European Community (range: -40.5 to -72 VDC (-75 VDC FOR 5mS)) -40 VDC to -72 VDC steady-state input voltage
Input current rating1	60 A maximum (1x)—Original series 40 A maximum (2x)—Enhanced series
Source DC service requirement1	Sufficient to supply the rated input current. Local codes apply.
Redundancy	2 DC power entry modules required for 2N redundancy

1 For each DC power entry module.

---

Caution To ensure that the chassis configuration complies with the required power budgets, use the on-line power calculator. Failure to properly verify the configuration may result in an unpredictable state if one of the power units fails. Contact your local sales representative for assistance.

---

Table A-4 Environmental Specifications

Description	Value
Temperature	Operating: 32° to 104°F (0° to 40°C) Nonoperating: -4° to 149°F (-20° to 65°C)
Humidity	Operating: 10 to 85% noncondensing Nonoperating: 5 to 95% noncondensing
Altitude	Operating: 0 to 10,000 ft (0 to 3,000 m) Nonoperating: 0 to 15,000 ft (0 to 4,570 m)
Heat dissipation	8,296 BTU/hr maximum (original series) 9,554 BTU/hr maximum (enhanced series)
Acoustic noise	70 dBa maximum
Shock	Operating (halfsine): 21 in/sec (0.53 m/sec) Nonoperating (trapezoidal pulse): 20 G1 , 52 in/sec (1.32 m/sec)
Vibration	Operating: 0.35 Grms2 from 3 to 500 Hz Nonoperating: 1.0 Grms from3 to 500 Hz

1 G is a value of acceleration, where 1G equals 32.17 ft/sec2 (9.81 m/sec2). 2 Grms is the root mean square value of acceleration.