-
Cisco IOS XR System Monitoring Command Reference, Release 3.8
-
Preface
-
Alarm Management and Logging Correlation Commands on Cisco IOS XR Software
-
Embedded Event Manager Commands on Cisco IOS XR Software
-
IP Service Level Agreement Commands on Cisco IOS XR Software
-
Logging Services Commands on Cisco IOS XR Software
-
Onboard Failure Logging Commands on Cisco IOS XR Software
-
Performance Management Commands on Cisco IOS XR Software
-
Statistics Service Commands on Cisco IOS XR Software
-
Index
-
Feedback
Table Of Contents
Embedded Event Manager Commands on Cisco IOS XR Software
event manager scheduler suspend
show event manager directory user
show event manager environment
show event manager metric hardware
show event manager metric process
show event manager policy available
show event manager policy registered
show event manager refresh-time
show event manager statistics-table
Embedded Event Manager Commands on Cisco IOS XR Software
This chapter describes the commands used to set Embedded Event Manager (EEM) operational attributes and monitor EEM operations.
The Cisco IOS XR EEM is the central clearinghouse for events detected by any portion of Cisco IOS XR High Availability Services. The EEM is responsible for fault detection, fault recovery, and process reliability statistics in the system. The EEM is policy driven and lets you configure the high-availability features of the system to fit your needs.
The EEM monitors the reliability rates achieved by each process in the system. You can use these metrics during testing to identify components that do not meet their reliability or availability goals, allowing you to take corrective action.
For detailed information about EEM concepts, configuration tasks, and examples, see the Configuring and Managing Embedded Event Manager Policies on Cisco IOS XR Software module in Cisco IOS XR System Monitoring Configuration Guide.
event manager directory user
To specify a directory to use for storing user library files or user-defined Embedded Event Manager (EEM) policies, use the event manager directory user command in global configuration mode. To disable use of a directory for storing user library files or user-defined EEM policies, use the no form of this command.
event manager directory user {library path | policy path}
no event manager directory user {library path | policy path}
Syntax Description
library
Specifies a directory for storing user library files.
path
Absolute pathname to the user directory on the flash device.
policy
Specifies a directory for storing user-defined EEM policies.
Defaults
No directory is specified for storing user library files or user-defined EEM policies.
Command Modes
Global configuration
Command History
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Cisco IOS XR software supports only policy files created by using the Tool Command Language (TCL) scripting language. TCL software is provided in the Cisco IOS XR software image when the EEM is installed on the network device. Files with the .tcl extension can be EEM policies, TCL library files, or a special TCL library index file named tclindex. The tclindex file contains a list of user function names and the library files that contain the user functions ("procedures"). The EEM searches the user library directory when TCL starts to process the tclindex file.
User Library
The user library directory is needed to store user library files associated with authoring EEM policies. If you have no plans to write EEM policies, you do not need to create a user library directory.
To create the user library directory before identifying it to the EEM, use the mkdir command in EXEC mode. After creating the user library directory, you can then use the copy command to copy .tcl library files into the user library directory.
User Policy
The user policy directory is needed to store user-defined policy files. If you have no plans to write EEM policies, you do not need to create a user policy directory. The EEM searches the user policy directory when you enter the event manager policy policy-name user command.
To create the user policy directory before identifying it to the EEM, use the mkdir command in EXEC mode. After creating the user policy directory, you can then use the copy command to copy policy files into the user policy directory.
Task ID
Examples
The following example shows how to set the pathname for the user library directory to /usr/lib/tcl on disk0:
RP/0/RP0/CPU0:router(config)# event manager directory user library disk0:/usr/lib/tclThe following example shows how to set the location of the EEM user policy directory to /usr/fm_policies on disk0:
RP/0/RP0/CPU0:router(config)# event manager directory user policy disk0:/usr/fm_policiesRelated Commands
event manager environment
To set an Embedded Event Manager (EEM) environment variable, use the event manager environment command in global configuration mode. To remove the configuration, use the no form of this command.
event manager environment var-name [var-value]
no event manager environment var-name
Syntax Description
var-name
Name assigned to the EEM environment configuration variable.
var-value
(Optional) Series of characters, including embedded spaces, to be placed in the environment variable var-name.
Defaults
No default behavior or values
Command Modes
Global configuration
Command History
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Environment variables are available to EEM policies when you set them using the event manager environment command; they become unavailable when you remove them with the no form of this command.
By convention, the names of all environment variables defined by Cisco begin with an underscore character to set them apart (for example, _show_cmd).
Spaces may be used in the var-value argument. This command interprets everything after the var-name argument to the end of the line to be part of the var-value argument.
Use the show event manager environment command to display the name and value of all EEM environment variables before and after they have been set using the event manager environment command.
Task ID
Examples
The following example shows how to define a set of EEM environment variables:
RP/0/RP0/CPU0:router(config)# event manager environment _cron_entry 0-59/2 0-23/1 * * 0-7RP/0/RP0/CPU0:router(config)# event manager environment _show_cmd show eem manager policy registeredRP/0/RP0/CPU0:router(config)# event manager environment _email_server alpha@cisco.comRP/0/RP0/CPU0:router(config)# event manager environment _email_from beta@cisco.comRP/0/RP0/CPU0:router(config)# event manager environment _email_to beta@cisco.comRP/0/RP0/CPU0:router(config)# event manager environment _email_ccRelated Commands
event manager policy
To register an Embedded Event Manager (EEM) policy with the EEM, use the event manager policy command in global configuration mode. To unregister an EEM policy with the EEM, use the no form of this command.
event manager policy policy-name username username [persist-time [seconds | infinite] | type {system | user}]
no event manager policy policy-name [username username]
Syntax Description
Defaults
The default persist time is 1 hour (3600 seconds).
Command Modes
Global configuration
Command History
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
The EEM schedules and runs policies on the basis of an event specification that is contained within the policy itself. When the event manager policy command is invoked, the EEM examines the policy and registers it to be run when the specified event occurs. An EEM script is available to be scheduled by the EEM until the no form of this command is entered.
Note
AAA authorization (such as the aaa authorization command with the eventmanager and default keywords) must be configured before EEM policies can be registered. The eventmanager and default keywords must be configured for policy registration. See the "Configuring AAA Services on Cisco IOS XR Software" module of Cisco IOS XR Software System Security Configuration Guide for more information on AAA authorization configuration.
Username
Enter the username that will execute the script with the keyword and argument username username. This name can be different from the user who is currently logged in, but the registering user must have permissions that are a superset of the username that will run the script. Otherwise, the script will not be registered and the command will be rejected. In addition, the username that will run the script must have access privileges to the commands issued by the EEM policy being registered.
Persist-time
When a script is first registered, the configured username for the script is authenticated. If authentication fails, or if the AAA server is down, the script registration fails.
After the script is registered, the username is authenticated again each time a script is run.
If the AAA server is down, the username authentication can be read from memory. The persist-time determines the number of seconds this username authentication is held in memory.
•
•
Note
The following values can be used for persist-time.
•
•
•
Type
If you enter the event manager policy command without specifying the type keyword, the EEM first tries to locate the specified policy file in the system policy directory. If the EEM finds the file in the system policy directory, it registers the policy as a system policy. If the EEM does not find the specified policy file in the system policy directory, it looks in the user policy directory. If the EEM locates the specified file in the user policy directory, it registers the policy file as a user policy. If the EEM finds policy files with the same name in both the system policy directory and the user policy directory, the policy file in the system policy directory takes precedence and the policy file is registered as a system policy.
Task ID
Examples
The following example shows how to register a user-defined policy named "cron.tcl" located in the user policy directory:
RP/0/RP0/CPU0:router(config)# event manager policy username lab cron.tcl userRelated Commands
event manager refresh-time
To define the time between refreshes of user authentication for Embedded Event Manager (EEM), use the event manager refresh-time command in global configuration mode. To restore the system to its default condition, use the no form of this command.
event manager refresh-time seconds
no event manager refresh-time seconds
Syntax Description
Defaults
The default refresh time is 30 minutes (1800 seconds).
Command Modes
Global configuration
Command History
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
EEM attempts to contact the AAA server and refresh the username reauthenticate whenever the configured refresh-time expires.
Task ID
Examples
The following example shows how to set the refresh time:
RP/0/RP0/CPU0:router(config)# event manager refresh-time 1900event manager run
To manually run an Embedded Event Manager (EEM) policy, use the event manager run command in EXEC mode.
event manager run policy [argumen[...[argument15]]]
Syntax Description
policy
Name of the policy file.
[argumen[...[argument15]]]
Argument that you want to pass to the policy. The maximum number of arguments is 15.
Defaults
No registered EEM policies are run.
Command Modes
EXEC
Command History
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
EEM usually schedules and runs policies on the basis of an event specification that is contained within the policy itself. The event manager run command allows policies to be run manually.
You can query the arguments in the policy file by using the tcl command event_reqinfo, as shown in the following example:
array set arr_einfo [event_reqinfo]set argc $arr_einfo(argc)set arg1 $arr_einfo(arg1)Use the event manager policy command to register the policy before using the event manager run command to run the policy. The policy can be registered with none as the event type.
Task ID
Examples
The following example of the event manager run command shows how to manually run an EEM policy named policy-manual.tcl:
RP/0/RP0/CPU0:router# event manager run policy-manual.tcl parameter1 parameter2 parameter3RP/0/RP0/CPU0:Sep 20 10:26:31.169 : user-plocy.tcl[65724]: The reqinfo of arg2 is parameter2.RP/0/RP0/CPU0:Sep 20 10:26:31.170 : user-plocy.tcl[65724]: The reqinfo of argc is 3.RP/0/RP0/CPU0:Sep 20 10:26:31.171 : user-plocy.tcl[65724]: The reqinfo of arg3 is parameter3.RP/0/RP0/CPU0:Sep 20 10:26:31.172 : user-plocy.tcl[65724]: The reqinfo of event_type_string is none.RP/0/RP0/CPU0:Sep 20 10:26:31.172 : user-plocy.tcl[65724]: The reqinfo of event_pub_sec is 1190283990.RP/0/RP0/CPU0:Sep 20 10:26:31.173 : user-plocy.tcl[65724]: The reqinfo of event_pub_time is 1190283990.RP/0/RP0/CPU0:Sep 20 10:26:31.173 : user-plocy.tcl[65724]: The reqinfo of event_id is 3.RP/0/RP0/CPU0:Sep 20 10:26:31.174 : user-plocy.tcl[65724]: The reqinfo of arg1 is parameter1.RP/0/RP0/CPU0:Sep 20 10:26:31.175 : user-plocy.tcl[65724]: The reqinfo of event_type is 16.RP/0/RP0/CPU0:Sep 20 10:26:31.175 : user-plocy.tcl[65724]: The reqinfo of event_pub_msec is 830Related Commands
event manager scheduler suspend
To suspend Embedded Event Manager (EEM) policy scheduling execution immediately, use the event manager scheduler suspend command in global configuration mode. To restore the system to its default condition, use the no form of this command.
event manager scheduler suspend
no event manager scheduler suspend
Syntax Description
This command has no arguments or keywords.
Defaults
Policy scheduling is active by default.
Command Modes
Global configuration
Command History
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the event manager scheduler suspend command to suspend all policy scheduling requests and do no scheduling until you enter the no form of this command. The no form of this command resumes policy scheduling and runs any pending policies.
You might want to suspend policy execution immediately instead of unregistering policies one by one for the following reasons:
•
•
Task ID
Examples
The following example shows how to disable policy scheduling:
RP/0/RP0/CPU0:router(config)# event manager scheduler suspendThe following example shows how to enable policy scheduling:
RP/0/RP0/CPU0:router(config)# no event manager scheduler suspendRelated Commands
show event manager directory user
To display the directory to use for storing user library files or user-defined Embedded Event Manager (EEM) policies, use the show event manager directory user command in EXEC mode.
show event manager directory user {library | policy}
Syntax Description
Defaults
No default behavior or values
Command Modes
EXEC
Command History
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show event manager directory user command to get the current value of the EEM user library or policy directory.
Task ID
Examples
The following is sample output from the show event manager directory user command:
RP/0/RP0/CPU0:router# show event manager directory user librarydisk0:/fm_user_lib_dirRP/0/RP0/CPU0:router# show event manager directory user policydisk0:/fm_user_pol_dirRelated Commands
show event manager environment
To display the names and values of Embedded Event Manager (EEM) environment variables, use the show event manager environment command in EXEC mode.
show event manager environment [all | environment-name]
Syntax Description
all
(Optional) Specifies all environment variables.
environment-name
(Optional) Environment variable for which data is displayed.
Defaults
All environment variables are displayed.
Command Modes
EXEC
Command History
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use show event manager environment command to display the name and value of EEM environment variables.
Task ID
Examples
The following is sample output from the show event manager environment command:
RP/0/RP0/CPU0:router# show event manager environmentNo. Name Value1 _email_cc2 _email_to mosnerd@cisco.com3 _show_cmd show event manager policy registered4 _cron_entry 0-59/2 0-23/1 * * 0-75 _email_from mosnerd@cisco.com6 _email_server zeta@cisco.comTable 7 describes the significant fields shown in the display.
Related Commands
show event manager metric hardware
To display Embedded Event Manager (EEM) reliability data for processes running on a particular node, use the show event manager metric hardware command in EXEC mode.
show event manager metric hardware location {node-id | all}
Syntax Description
location
Specifies the location of the node.
node-id
EEM reliability data for a specified node. The node-id argument is entered in the rack/slot/module notation.
all
Specifies all nodes.
Defaults
No default behavior or values
Command Modes
EXEC
Command History
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show event manager metric hardware command to display EEM reliability data for processes running on a particular node
Task ID
Examples
The following is sample output from the show event manager metric hardware command:
RP/0/RP0/CPU0:router# show event manager metric hardware location 0/RP1/CPU0=====================================node: 0/RP1/CPU0Most recent online: Mon Sep 10 21:45:02 2007Number of times online: 1Cumulative time online: 0 days, 09:01:07Most recent offline: n/aNumber of times offline: 0Cumulative time offline: 0 days, 00:00:00Table 8 describes the significant fields shown in the display.
Related Commands
show event manager metric process
To display Embedded Event Manager (EEM) reliability metric data for processes, use the show event manager metric process command in EXEC mode.
show event manager metric process {all | job-id | process-name} location {all | node-id}
Syntax Description
Defaults
No default behavior or values
Command Modes
EXEC
Command History
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
The system maintains a record of when processes start and end. This data is used as the basis for reliability analysis.
Use the show event manager metric process command to obtain availability information for a process or group of processes. A process is considered available when it is running.
Task ID
Examples
The following is sample output from the show event manager metric process command:
RP/0/RP0/CPU0:router# show event manager metric process all location all=====================================job id: 88, node name: 0/4/CPU0process name: wd-critical-mon, instance: 1--------------------------------last event type: process startrecent start time: Wed Sep 19 13:31:07 2007recent normal end time: n/arecent abnormal end time: n/anumber of times started: 1number of times ended normally: 0number of times ended abnormally: 0most recent 10 process start times:--------------------------Wed Sep 19 13:31:07 2007--------------------------most recent 10 process end times and types:cumulative process available time: 21 hours 1 minutes 31 seconds 46 millisecondscumulative process unavailable time: 0 hours 0 minutes 0 seconds 0 millisecondsprocess availability: 1.000000000number of abnormal ends within the past 60 minutes (since reload): 0number of abnormal ends within the past 24 hours (since reload): 0number of abnormal ends within the past 30 days (since reload): 0=====================================job id: 54, node name: 0/4/CPU0process name: dllmgr, instance: 1--------------------------------last event type: process startrecent start time: Wed Sep 19 13:31:07 2007recent normal end time: n/arecent abnormal end time: n/anumber of times started: 1number of times ended normally: 0number of times ended abnormally: 0most recent 10 process start times:--------------------------Wed Sep 19 13:31:07 2007--------------------------most recent 10 process end times and types:cumulative process available time: 21 hours 1 minutes 31 seconds 41 millisecondscumulative process unavailable time: 0 hours 0 minutes 0 seconds 0 millisecondsprocess availability: 1.000000000number of abnormal ends within the past 60 minutes (since reload): 0number of abnormal ends within the past 24 hours (since reload): 0number of abnormal ends within the past 30 days (since reload): 0Table 9 describes the significant fields shown in the display.
Related Commands
show event manager policy available
To display Embedded Event Manager (EEM) policies that are available to be registered, use the show event manager policy available command in EXEC mode.
show event manager policy available [system | user]
Syntax Description
system
(Optional) Displays all available system policies.
user
(Optional) Displays all available user policies.
Defaults
If this command is invoked with no optional keywords, it displays information for all available system and user policies.
Command Modes
EXEC
Command History
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show event manager policy available command to find out what policies are available to be registered just prior to using the event manager policy command to register policies.
This command also is useful if you forget the exact name of a policy required for the event manager policy command.
Task ID
Examples
The following is sample output from the show event manager policy available command:
RP/0/RP0/CPU0:router# show event manager policy availableNo. Type Time Created Name1 system Tue Jan 12 09:41:32 2004 pr_sample_cdp_abort.tcl2 system Tue Jan 12 09:41:32 2004 pr_sample_cdp_revert.tcl3 system Tue Jan 12 09:41:32 2004 sl_sample_intf_down.tcl4 system Tue Jan 12 09:41:32 2004 tm_sample_cli_cmd.tcl5 system Tue Jan 12 09:41:32 2004 tm_sample_crash_hist.tcl6 system Tue Jan 12 09:41:32 2004 wd_sample_proc_mem_used.tcl7 system Tue Jan 12 09:41:32 2004 wd_sample_sys_mem_used.tclTable 10 describes the significant fields shown in the display.
Table 10 show event manager policy available Field Descriptions
No.
Number of the policy.
Type
Type of policy.
Time Created
Time the policy was created.
Name
Name of the policy.
Related Commands
Registers an EEM policy with the EEM.
Displays EEM policies that are already registered.
show event manager policy registered
To display Embedded Event Manager (EEM) policies that are already registered, use the show event manager policy registered command in EXEC mode.
show event manager policy registered [event-type type] [system | user] [time-ordered | name-ordered]
Syntax Description
Defaults
If this command is invoked with no optional keywords or arguments, it displays the registered EEM policies for all event types. The policies are displayed according to registration time.
Command Modes
EXEC
Command History
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
The output of the show event manager policy registered command is most helpful if you are writing and monitoring EEM policies. The output displays registered policy information in two parts. The first line in each policy description lists the index number assigned to the policy, policy type (system or user), type of event registered, time when the policy was registered, and name of the policy file. The remaining lines of each policy description display information about the registered event and how the event is to be handled, and come directly from the Tool Command Language (TCL) command arguments that make up the policy file.
Registered policy information is documented in the Cisco publication Writing Embedded Event Manager Policies Using Tcl.
Task ID
Examples
The following is sample output from the show event manager policy registered command:
RP/0/RP0/CPU0:router# show event manager policy registeredNo. Type Event Type Time Registered Name1 system proc abort Wed Jan 16 23:44:56 2004 test1.tclversion 00.00.0000 instance 1 path {cdp}priority normal maxrun_sec 20 maxrun_nsec 02 system timer cron Wed Jan 16 23:44:58 2004 test2.tclname {crontimer1}priority normal maxrun_sec 20 maxrun_nsec 03 system proc abort Wed Jan 16 23:45:02 2004 test3.tclpath {cdp}priority normal maxrun_sec 20 maxrun_nsec 04 system syslog Wed Jan 16 23:45:41 2004 test4.tcloccurs 1 pattern {test_pattern}priority normal maxrun_sec 90 maxrun_nsec 05 system timer cron Wed Jan 16 23:45:12 2004 test5.tclname {crontimer2}priority normal maxrun_sec 30 maxrun_nsec 06 system wdsysmon Wed Jan 16 23:45:15 2004 test6.tcltimewin_sec 120 timewin_nsec 0 sub1 mem_tot_used {node {localhost} op gtval 23000}priority normal maxrun_sec 40 maxrun_nsec 07 system wdsysmon Wed Jan 16 23:45:19 2004 test7.tcltimewin_sec 120 timewin_nsec 0 sub1 mem_proc {node {localhost} procname{wdsysmon} op gt val 80 is_percent FALSE}priority normal maxrun_sec 40 maxrun_nsec 0Table 11 describes the significant fields shown in the display.
Related Commands
show event manager refresh-time
To display the time between refresh of user authentication for Embedded Event Manager (EEM), use the show event manager refresh-time command in EXEC mode.
show event manager refresh-time
Syntax Description
This command has no arguments or keywords.
Defaults
No default behavior or values
Command Modes
EXEC
Command History
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Output from the show event manager refresh-time command is the refresh time in seconds.
Task ID
Examples
The following is sample output from the show event manager refresh-time command:
RP/0/RP0/CPU0:router# show event manager refresh-time1800 secondsRelated Commands
Specifies time between system attempts to contact the AAA server and refreshes the username reauthentication.
show event manager statistics-table
To display the currently supported statistic counters maintained by the Statistic Event Detector, use the show event manager statistics-table command in EXEC mode.
show event manager statistics-table {stats-name | all}
Syntax Description
Defaults
No default behavior or values
Command Modes
EXEC
Command History
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show event manager statistics-table all command to display output for all statistics types.
Task ID
Examples
The following is sample output from the show event manager statistics-table all command:
RP/0/RP0/CPU0:router# show event manager statistics-table allName Type Descriptionifstats-generic bag Interface generic statsifstats-iftable bag Interface iftable statsifstats-datarate bag Interface datarate statsThe following is sample output providing more detailed information on the "ifstats-iftable" interface statistics table:
RP/0/RP0/CPU0:router# show event manager statistics-table ifstats-iftableName Type DescriptionPacketsReceived uint64 Packets rcvdBytesReceived uint64 Bytes rcvdPacketsSent uint64 Packets sentBytesSent uint64 Bytes sentMulticastPacketsReceived uint64 Multicast pkts rcvdBroadcastPacketsReceived uint64 Broadcast pkts rcvdMulticastPacketsSent uint64 Multicast pkts sentBroadcastPacketsSent uint64 Broadcast pkts sentOutputDropsCount uint32 Total output dropsInputDropsCount uint32 Total input dropsInputQueueDrops uint32 Input queue dropsRuntPacketsReceived uint32 Received runt packetsGiantPacketsReceived uint32 Received giant packetsThrottledPacketsReceived uint32 Received throttled packetsParityPacketsReceived uint32 Received parity packetsUnknownProtocolPacketsReceiveduint32 Unknown protocol pkts rcvdInputErrorsCount uint32 Total input errorsCRCErrorCount uint32 Input crc errorsInputOverruns uint32 Input overrunsFramingErrorsReceived uint32 Framing-errors rcvdInputIgnoredPackets uint32 Input ignored packetsInputAborts uint32 Input abortsOutputErrorsCount uint32 Total output errorsOutputUnderruns uint32 Output underrunsOutputBufferFailures uint32 Output buffer failuresOutputBuffersSwappedOut uint32 Output buffers swapped outApplique uint32 AppliqueResetCount uint32 Number of board resetsCarrierTransitions uint32 Carrier transitionsAvailabilityFlag uint32 Availability bit maskNumberOfSecondsSinceLastClearCountersuint32 Seconds since last clear countersLastClearTime uint32 SysUpTime when counters were last cleared (in seconds)Table 12 describes the significant fields shown in the display.
Related Commands
