-
Cisco IOS XR System Error Message Reference Guide, Release 3.8
-
Preface
-
Overview
-
Access Control List (ACL) Messages
-
Application Infrastructure Messages
-
Diagnostic Messages
-
Fabric Messages
-
Forwarding Messages
-
High Availability (HA) Messages
-
Installation Messages
-
Internet Protocol (IP) Messages
-
Layer 1 Messages
-
Layer 2 Messages
-
Layer 3 Messages
-
License Messages
-
Media Messages
-
Manageability (MGBL) Messages
-
Operating System (OS) Messages
-
Platform Messages
-
Quality of Service (QoS) Messages
-
Routing Messages
-
Security Messages
-
Services Messages
-
Simple Network Management Protocol (SNMP) Messages
-
System Database Messages
-
Index
-
FeedbackTable Of Contents
IP_STATIC_BFD_SESSMGR Messages
IPV4_MCAST_NETIO_DEBUG Messages
POLICY_REPOSITORY_DYNREG Messages
POLICY_REPOSITORY_EDM Messages
Routing Messages
This section contains all routing related System Error Messages, such as MPLS, OSPF, BGP, Multicast, MRIB, RIB, and so forth. The following facility codes are represented in this module:
•
IP_STATIC_BFD_SESSMGR Messages
•
•
•
AIB Messages
Error Message%ROUTING-AIB-1-EVENTBLOCK event_block returned early : [chars] (errno equals [dec])
Explanation An unexpected or erroneous return while waiting for events.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AIB-4-INDEX_REG_FAIL AIB process cannot register with the platform specific DLL (return equals [dec])
Explanation The AIB process cannot register with the platform specific adjacency index DLL. The adjacency database will not be created.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AIB-4-INDEX_VERSION_FAIL AIB process has detected a version mismatch between itself and the platform DLL (DLL version is [dec], AIB expected [dec])
Explanation The AIB process has detected that the platform specific adjacency indexing DLL has reported a version number that does not match the AIB process version number. Due to this inconsistency, the AIB cannot continue and the system will not be able to process any adjacency information.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AIB-4-LTRACE_ERROR Failed to open trace file: [chars]
Explanation The AIB process was unable to open the trace buffer for automatic tracing (show trace adjacency may not work).
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AIB-4-RADIXINIT_FAIL AIB failed to initialize the interface db radix tree ([chars])
Explanation Initialization of the radix tree could not be accomplished because of a low memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-AIB-4-SHM_FAIL AIB Shared memory error: [chars] [chars]
Explanation The AIB process received an error while trying to initialize the shared memory.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AIB-4-SYSTEM_FAIL [chars] [chars] (errno equals [dec])
Explanation There was a system call failure resulting in a failure to provide a system service as indicated in the message text.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
AUTORP_CRP Messages
Error Message%ROUTING-AUTORP_CRP-3-BAG_RELATED_ERROR Bag related error: [chars]
Explanation The Candidate RP had trouble wth Bags.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-EDM_ACCESS_ERROR Sysdb EDM related error: [chars], [chars]
Explanation The Candidate RP had trouble accessing SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-EVENT_CONN_MGR_ERROR Event connection manager error : [chars], [chars]
Explanation Failed to open connection to Connection Manager.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-EVENT_MGR_CREATE_FAILED Failed to create an event manager
Explanation A problem occurred when a call to event_manager_create() was made.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-GEN_ERROR Error : [chars] failed - [chars]
Explanation General Error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-IM_RELATED_ERROR A call to [chars] returned [chars]
Explanation A problem occurred when a call to IM was made.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-INIT_FAILED Initialization failed : [chars]
Explanation autorp_candidate_rp failed to initialize successfully.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-IPARM_RELATED_FAILURE A call to [chars] returned [chars]
Explanation A problem occurred when a call to one of the IPARM APIs was made.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-MALLOC_FAILED malloc() failed : failed to allocate memory to receive messages
Explanation A call to malloc() failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-SOCKET_ERROR Socket Error : [chars] : [chars]
Explanation Socket Error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-SYSDB_ACCESS_ERROR Sysdb related error: [chars], [chars]
Explanation The Candidate RP had trouble accessing SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-SYSDB_REGISTRATION_FAILED Sysdb registration error: [chars]
Explanation The Candidate RP had trouble registering as a notifier with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-TIMER_ERROR Timer Error : [chars]
Explanation Timer Error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-TUPLE_ERROR Tuple operation error : [chars]
Explanation Tuple operation failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
AUTORP_MAP Messages
Error Message%ROUTING-AUTORP_MAP-3-BAG_RELATED_ERROR Bag related error: [chars]
Explanation The Mapping Agent had trouble wth Bags.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-DEBUG_ERROR Debug error : [chars]
Explanation Debug Error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-EDM_ACCESS_ERROR Sysdb EDM related error: [chars], [chars]
Explanation The Mapping Agent had trouble accessing SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-EVENT_CONN_MGR_ERROR Event connection manager error: [chars], [chars]
Explanation Failed to open connection to Connection Manager.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-EVENT_MGR_CREATE_FAILED A call to event_manager_create() failed
Explanation A problem occurred while calling the event_manager_create() API.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-IM_RELATED_ERROR The function [chars] returned error : [chars]
Explanation Failed some IM related operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-INIT_FAILED Initialization failed : [chars]
Explanation autorp_mapping_agent failed to initialize successfully.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-INIT_FAILED_ERR '[chars]' initialization failed : [chars]
Explanation autorp_mapping_agent failed to initialize successfully
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-IPARM_RELATED_FAILURE A call to [chars] returned [chars]
Explanation A problem occurred when a call to one of the IPARM APIs was made.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-MALLOC_FAILED malloc() failed : failed to allocate memory to receive messages
Explanation A call to malloc() failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-OOR_LIMIT Cache maximum reached: [dec], new group range not added
Explanation OOR Error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-RTREE_ERROR RTree error : [chars]
Explanation Timer Error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-SOCKET_ERROR Socket Error : [chars] : [chars]
Explanation Socket Error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-SYSDB_ACCESS_ERROR Sysdb related error: [chars], [chars]
Explanation The Mapping Agent had trouble accessing SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-SYSDB_REGISTRATION_FAILED Sysdb registration error: [chars]
Explanation The Mapping Agent had trouble registering as a notifier/edm with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-TIMER_ERROR Timer Error : [chars]
Explanation Timer Error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-TUPLE_ERROR Tuple operation error : [chars]
Explanation Tuple operation failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
BGP_VRF Messages
Error Message%ROUTING-BGP_VRF-3-DUPLICATE_ID Failed to store [chars] ID [hex] for VRF [chars].
Explanation A ID has been received from RSI that duplicates an existing VRF or table ID. As a result, the new ID has been ignored, and subsequent operation for that VRF will be incorrect.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP_VRF-3-INIT Initialization failed ([chars]%s)
Explanation An error occurred while initializing the BGP VRF module. The BPM process will be restarted.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP_VRF-3-NOTIFY Failed to apply configuration change for: [chars] ([chars]).
Explanation A notification of a configuration change could not be applied, leaving the internal data structures inconsistent with the configuration.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP_VRF-3-RD_APPLY Failed to apply RD configuration change for [chars]. System may now be in an inconsistent state.
Explanation The RD value for the VRF failed to be set, leaving the internal data structures inconsistent with the configuration.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP_VRF-3-RD_PUBLISH Failed to publish RD configuration: [chars]. System may now be in an inconsistent state.
Explanation The RD value for a VRF or set of VRFs failed to be published.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
BGP Messages
Error Message%ROUTING-BGP-2-ADDROUTE Failed to add net [chars] to the BGP table
Explanation An error occurred whilst trying to insert a net to the BGP table database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-2-BRIB_API_SYNC bRIB API detected loss of sync: invalid [chars] [hex] at [hex]
Explanation The data stream between the bRIB and a speaker was corrupted and the receiving process could not interpret the received message.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-2-ERR_EVM_EVENT_BLOCK Error in event loop for [chars] thread: [chars]
Explanation An error occurred in the event loop.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-2-ERR_FILE_ATTACH Failed to do [chars] event file attach - [chars]
Explanation An error occurred when bgp try to do event file attach.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-2-ERR_MEM_ALLOC Failed to allocate memory for [chars]
Explanation The requested operation could not be accomplished because of a low memory condition. BGP may not operate correctly until the process is restarted.
Recommended Action Reduce other system activity to ease memory demands, then restart the process. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-BGP-2-ERR_THREAD_DEADLOCK Deadlock detected (thread [unsigned int]): holding: [chars]
Explanation BGP detected a lock being held when all locks should have been released.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-2-FATAL_WRAPPER Fatal error: A call to [chars] failed unexpectedly: [chars]
Explanation A function call failed unexpectedly - this is probably a system problem
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-AF_LIB_FILE_ERROR Failed to read Address Family data file: [chars] [chars]
Explanation 'File/Directory open operation failed, or the data in the file was corrupt'
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-AF_LIB_FILE_WRONG_INFO Failed to read Address Family data file [chars]: [chars] on line [unsigned int]
Explanation 'The data in the Address Family data file was corrupt'
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ALREADY_DONE Cannot [chars]%s: already done
Explanation An operation could not be performed because it had already been completed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ATTRKEY_BAD Failed to [chars] RIB due to an invalid attribute key number ([hex])
Explanation There is a problem with the attribute key generation routine.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ATTRKEY_CHKPT Failed to checkpoint attribute key
Explanation The chkpt library failed to checkpoint the attribute key number. Normal operation of BGP (standalone) or bRIB (distributed) is not impacted unless the process is restarted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ATTRKEY_OVERFLOW Failed to generate a new attribute key for the incoming UPDATE
Explanation This is an extremely rare case where the attribute key overflow protection mechanism fails.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-BAD_REFCNT Bad reference count value ([unsigned int]) for [chars] ([pointer])
Explanation 'This indicates a internal data structure inconsistency'
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-BPM_AS_INIT As-num is not set yet in bpm and can not apply other config
Explanation Should not attempt to publish anything untill AS number is set.
Recommended Action This warnning will show up for possible out of order sysdb notification
Error Message%ROUTING-BGP-3-BPM_INIT Initialization failed ([chars]%s)
Explanation An error occurred while initializing the BGP process manager. If this occurred during process startup or RP Switchover, then the process may be restarted.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-BPM_PROCESS_START Failed to start [chars] process (ID: [unsigned int]): [chars]
Explanation The BPM failed to start the process in the error message. As a result, the process will not be running.
Recommended Action Check that the process is not already running using the 'show process bgp location all' or 'show process brib location all' command as appropriate. If the process is not running, attempt to start it using the 'process restart' command. If other error messages are seen along with this one, or when attempting to manually start the process, please consult the documentation for those errors and attempt to rectify them. If problems persist, copy this error message and any others exactly as they appear on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-BPM_PROCESS_STOP Failed to stop [chars] process (ID: [unsigned int]): [chars]
Explanation An error occurred when trying to stop the process specified in the error message. As a result, the process may still be running, which could adversely affect the operation of other processes.
Recommended Action Check whether the process is still running using the 'show process bgp location all' or 'show process brib location all' command as appropriate. If the process is running, kill it using the 'process kill' command. If problems persist, copy this error message and any subsequent ones exactly as they appear on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-BPM_SWITCH_MODE Failed to switch to [chars] mode: [chars] ([chars])
Explanation An error occurred when switching between standalone and distributed mode.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-BRIB_INIT Initialization failed ([chars]%s)
Explanation An error occurred while initializing the BGP RIB. If this occured during process startup or RP Switchover, then the process may be restarted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-BUF_TOO_SHORT A string buffer was too short during a string print operation (string [chars] truncated)
Explanation Whilst trying to format a string, the buffer passed in was too short and the string was truncated.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-COMM_DECODE_RDINFO [chars] [unsigned int] [unsigned int]
Explanation Standby BGP received invalid Route Distinguisher information from Active BGP. *SUPPORT*
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-CONFIG_DEL Notify delete of [chars] failed with warning: [chars], no further action necessary.
Explanation A speaker or the bRIB failed to process the removal of some configuration.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-CONFIG_FALLOVER Apply for fast-external-fallover failed: [chars]
Explanation A speaker failed to process a configuration change for 'fast-external-fallover'
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-CONFIG_SET Notify for [chars] failed with error: [chars], system may now be in an inconsistent state.
Explanation A speaker or the bRIB failed to process a configuration change.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-CREATE_REGS Create Registration failed: intfhandle ([unsigned int]) for interface [chars]
Explanation 'Create and Delete Registration Failed for the named interface'
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-DEBUG_CONFIG Failed to apply debug configuration: [chars]
Explanation An error occurred whilst applying the debug configuration
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-DELPATH Attempted to delete path from empty net [chars]
Explanation An attempt was made to delete a path from a net with a path count of 0
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-DLL_ERROR Failed to [chars] [chars] DLL: [chars]
Explanation An error occurred whilst trying to open or initialize a DLL. The process will be restarted if this error occurs during process startup.
Recommended Action If the process has been restarted and the problem recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-EDM_INIT_FAILED EDM server initialization failed: [chars]: [chars]
Explanation Initialization of the EDM server failed. The process will be restarted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ERR_ALM_API ALM/LSD API: [chars] - [chars] failed
Explanation An ALM/LSD API returned an error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ERR_ALM_ONE_LABEL Unable to allocate label: [chars]
Explanation The ALM/LSD API was unable to allocate a requested label.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ERR_GENERAL [chars]
Explanation A non-fatal fault occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-EXTCOMM Failed to create extended community: [chars]
Explanation The import table list associated with an extended community set could not be created. This can occur if there is insufficient memory to allocate the import table list, or the number of importing tables exceeds the hard coded limit on the number of tables that a route may be imported into.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-EXTCOMM_ADD Failed to add one or more [chars] extended community for table [chars] prefix [chars]
Explanation While attaching extended communities to the path attribute we reached the maximum extended community limit and as a result we failed to add one or more extended community to the path attribute.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-GWCTX_CREATE Failed to [chars] for Gateway Context (VRF [chars], Gateway address-family [chars])
Explanation A software error has occurred whilst trying to initialize gateway context database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-HA_INIT Initialization failed ([chars]%s)
Explanation High Availabality initialization failed. If this occured during process startup or RP Switchover, then the process may be restarted.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-IFACE_LOOKUP Interface lookup for [chars] Failed: [chars]
Explanation Interface manager failed to lookup nexthop interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-IM_DMZLINK_BW Failed to register for DMZ link bandwidth change for neighbor [chars]: [chars]
Explanation BGP failed to register with interface manager for DMZ link bandwidth change notifiction for a given neighbor
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-IMPORT_INIT Initialization failed ([chars]%s)
Explanation An error occurred while initializing the import thread. If this occurred during process startup, then the process may be restarted.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-INIT_GET_VALUE Failed to obtain [chars] during initialization: [chars]
Explanation An error occurred when retrieving a required value during initialization. As a result the BGP process can not initialize.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-INSUFMEM Failed to allocate memory for [chars]
Explanation The requested operation could not be accomplished because of a low memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-BGP-3-INTERNAL_ERROR Internal error ([chars])
Explanation A non-fatal fault occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-INVAL_REDUNDANCY_ROLE Initialization failed ([chars]%s)
Explanation An invalid Redundancy Role was delivered to BGP. If this occured during process startup or RP Switchover, then the process may be restarted.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-IO_INIT Initialization failed: [chars] [chars] ([chars])
Explanation An error occurred while initializing the IO thread in speaker process. The process will be restarted.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-IO_INITSYNC_FAILED [chars] - set id [hex]
Explanation A problem occurred in TCP sync, retry TCP sync.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-IO_INITSYNC_SESSION_FAILED [chars] - for session, retry
Explanation A problem occurred in TCP init sync.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-LABEL_INIT Initialization of BGP/LABEL failed ([chars]:[chars])
Explanation An error occurred whilst initialising the LABEL thread. This could be caused by failure to allocate resources or by errors when calling the MPLS label manager.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-LOCK_RECURSIVE Attempt to recursively lock net [pointer] (lock: [hex])
Explanation A software error has occurred whilst trying to lock a network entry in the BGP Table database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-MAX_IMPORT No. of importing VRFs exceeds max ([unsigned int]), limited to [unsigned int] tables: (Err: [chars])
Explanation There is a hard coded limit on the number of tables that a route may be imported into. This limit has been exceeded, so the route may not be present in some of the importing tables. The limit is such that this message should not be seen under normal operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-MAX_VALUE_EXCEEDED The value of [chars] ([unsigned int]) exceeds the maximum value: [unsigned int]
Explanation The value of an internally computed variable has exceeded the maximum value
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-MIB_INIT Initialization failed ([chars]%s)
Explanation An error occurred while initializing the BGP MIB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-NEGCOUNTER Negative path or bestpath counter for peer [chars]
Explanation The counter value for accepted prefixes is wrong and less than zero
Recommended Action The counter can be corrected by resetting the session. However, the only behavior affected by an incorrect counter is enforcement of the 'max-prefix' command.
Error Message%ROUTING-BGP-3-NH_LOCK_RECURSIVE Attempt to recursively lock nexthop [pointer] (lock: [hex], vrf: [chars], afi: [chars])
Explanation A software error has occurred whilst trying to lock a nexthop entry in the BGP nexthop Table database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-NH_UNLOCK_ERR Failed to unlock nexthop node [pointer] (nh '[chars]', lock [hex], vrf '[chars]', afi '[chars]', cnt [unsigned int], ln [unsigned int])
Explanation A software error has occurred whilst trying to unlock an entry in the BGP nexthop Table database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-NOMEM_RESET Failed to allocate memory for [chars], resetting neighbor
Explanation The requested operation could not be accomplished because of a low memory condition. One or more neighbor sessions have been reset to free some memory.
Recommended Action In the problem recurs, reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-BGP-3-NOMSGCHUNK Failed to allocate [unsigned int] bytes from the memory pool for message of type [unsigned int]
Explanation A request was made to allocate a message size for which there was no memory pool large enough. This may indicate a software error in the calculation of the requested size.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-NOPAK_CONN Failed to clean up packet manger connection [chars]
Explanation A connection to the packet manager could not be established.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ORA_INSTBUILD Failed to build [chars]: [chars] ([chars])
Explanation Internal error in the routing policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ORA_ORABUILD Failed to build ORA[chars]: [chars] ([chars])
Explanation There was an internal error in the routing policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ORA_RUN Could not apply policy operation [chars] to attribute [chars] because [chars]
Explanation Internal error in the routing policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-OVERCOUNTER [chars] counter overflow
Explanation A counter with maximum value was incremented.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-QAD_FAILURE QAD failure - [chars]
Explanation BGP detected an error condition in QAD. String should contain more info.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-QAD_SEND_ERR QAD send err [chars] - BGP will reintialize NSR
Explanation An error occured to send msg to the QAD queue - this trigger nsr resynchronization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-QAD_TIMEOUT QAD timeout - BGP will reintialize NSR
Explanation A message is dropped in the QAD queue - this trigger nsr resynchronization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-RD_CREATE Failed to [chars] for RD [chars], address-family [chars]
Explanation A software error has occurred whilst trying to initialize RD node inside BGP Table database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-RD_LOCK_RECURSIVE Attempt to recursively lock rdinfo [pointer] (lock: [hex])
Explanation A software error has occurred whilst trying to lock a network entry in the BGP Table database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-RD_UNLOCK_ERR Failed to unlock RD node [pointer] (lock: [hex])
Explanation A software error has occurred whilst trying to unlock an entry in the BGP RD Table database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-REDIST_FAIL Failed to register with the RIB for redistribution of [chars] [chars] [chars] routes: [chars]
Explanation A RIB client library call for redistribution of routes failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-RIB_CONN_FAIL Failed to open connection to the RIB for address family [unsigned int]: [chars]
Explanation The connection to the RIB could not be established and a retry timer could not be started
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-RIB_FAIL Failed to [chars] for [chars] while calling the RIB instance [unsigned int]: [chars]
Explanation A RIB library call failed unexpectedly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-RIB_INIT Initialization failed ([chars]%s)
Explanation An error occurred while initializing the BGP RIB thread. The process will be restarted if this error occurs during process startup.
Recommended Action If the process has been restarted and the problem recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-RIB_INIT_FAIL Initialization to RIB failed for [chars]: [chars]
Explanation An error occurred whilst initialising the RIB for a new address family. This could be caused by failure to allocate resources or by errors when calling the Table Resource Manager or the RIB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-RIB_RETRY_FAIL RIB route retry failure: [chars] for [chars]
Explanation Some routes were not successfully installed in the RIB. Consequently, an attempt was made to save these routes to retry later. However, an error was encountered during the save attempt.
Recommended Action Issue a 'clear route address family sub-address family' to cause BGP routes to be reinstalled in the RIB. If this does not work, issue a soft or hard reset to all peers.
Error Message%ROUTING-BGP-3-RIB_TABLE_FAIL Failed to [chars] for [chars], RIB table [hex]
Explanation An error was encountered during some operation for the specified address family and RIB table. This could be due either to a lack of resources or a software problem.
Recommended Action Issue a 'clear route address family sub-address family' to cause BGP routes to be reinstalled in the RIB. If this does not work, issue a soft or hard reset to all peers.
Error Message%ROUTING-BGP-3-SCAN_INIT Scanner library initialization failed ([chars]%s)
Explanation An error occurred while initializing the scanner library. The process will be restarted.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-SPKR_INIT Initialization failed ([chars]%s)
Explanation An error occurred while initializing the BGP speaker process. If this occurred during process startup or RP Switchover, then the process may be restarted.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-TABLE_CREATE Failed to create table context for the vrf [chars] afi/safi [dec]/[dec]: [chars]
Explanation An error occurred when creating the table context for the shown vrf name, afi, safi. As a result table can't be activated.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-TBLATTR_VERSION Unable to propagate table attribute versions for [chars] : [chars]
Explanation An internal error was encountered.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-UNDERCOUNTER [chars] counter underflow
Explanation A counter with zero value was decremented.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-UNKNOWN_MEMSTATE BGP received a notification about an unknown memory state ([unsigned int])
Explanation BGP received a low memory notification from wdsysmon for an unknown memory state, ie not NORMAL, MINOR, SEVERE or CRITICAL. As a result, no action was taken.
Recommended Action Check the memory on the node, and if it is low, take manual action to release memory, eg by resetting some BGP neighbors (using the 'clear bgp' command).
Error Message%ROUTING-BGP-3-UNLOCK_ERR Failed to unlock net [pointer] (lock: [hex])
Explanation A software error has occurred whilst trying to unlock a network entry in the BGP Table database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-VRF_CREATE Failed to create VRF context for the vrf [chars] : [chars]
Explanation An error occurred when creating the vrf context for the shown vrf name. As a result VRF can't be enabled.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-VRF_DELETE VRF [chars] still has undeleted table afi/safi [dec]/[dec]. Table will be deleted.
Explanation An error occurred while deleting the VRF. An address-family table under the VRF is still not deleted. Ideally all the tables under the VRF should be deleted first before VRF is deleted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-4-ATTRKEY_INCONSISTENT BGP detected an inconsistency in attribute key generation. Will correct the problem by renumbering all attributes
Explanation The attribute key generation routine has gone beyond the checkpointed value. This is a rare condition to occur as the key generation algorithm is very simple.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-4-BFD_INVALID_NBR Attempt to register BFD session on invalid neighbor: [chars]
Explanation Internal error indicating that an attempt has been made to create a BFD session for a neighbor type that is not supported by BFD.
Recommended Action The BFD session for the neighbor in the log will not be created. If a BFD session for this neighbor is not required, no further action is needed. To re-attempt creation of a BFD session for this neighbor, remove and re-add the bfd fast-detect configuration for the neighbor.
Error Message%ROUTING-BGP-4-CAP_4BYTEAS Capability 4-byte-as suppress misconfigured for neighbor [chars]
Explanation Possible misconfiguration with 'capability 4-byte-as suppress'. This configuration can be inherited from either a neighbor-group or a session-group by a neighbor whose remote-as is a 4-byte as number. Suppress should be off for such neighbor.
Recommended Action Check the bgp configuration. Remove the 'capability 4-byte-as suppress' configuration or disable it to prevent getting inherited from the neighbor-group or a session-group
Error Message%ROUTING-BGP-4-DESTROY_CHUNK Chunk pool [chars] is no longer in use but cannot be destroyed
Explanation 'BGP has resized its bit fields, so the old bit field chunks should be ' 'destroyable. Nonetheless, BGP is unable to destroy the old chunk and, ' 'hence, cannot release unwanted memory.'
Recommended Action This error will not cause any erroneous behavior, hence no further action is needed to rectify the situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-4-ENCODE_NET_OVERRUN Encoding [chars] has overrun the msg buffer (writen size [unsigned int], max size [unsigned int])
Explanation Encodeing the net has overrun the msg buffer. It may corrupt some memory.
Recommended Action This warnning will showup for possible memory overrun.
Error Message%ROUTING-BGP-4-INCONSISTENT Detected inconsistent config state: [chars]
Explanation The internal state representing the configuration was invalid, but has now been fixed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-4-LOCK_ORDER Locking order violation (thread [unsigned int]): [chars] gained while holding: [chars]
Explanation BGP detected a violation of lock ordering requirements
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-4-LOCK_RELEASE Lock released without being held (thread [unsigned int]): [chars] gained [unsigned int], released [unsigned int]
Explanation BGP detected a lock being released when it was not held.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-4-MAXPFXEXCEED No. of [chars] prefixes received from [chars]: [unsigned int] exceed limit [unsigned int]
Explanation Number of prefixes received from a neighbor for a given address family has exceeded the limit configured with the 'max-prefix' command.
Recommended Action Check the prefixes received from the neighbor and verify whether the limit should be increased, or the neighbor is sending more prefixes than expected.
Error Message%ROUTING-BGP-4-POLICY_COMMUNITY_OVERFLOW Community overflow from policy application
Explanation Policy tried to add more communities than a BGP route can hold.
Recommended Action Find the affected neighbor with 'show bgp community truncated'. Modify policy on the affected neighbor to delete unnecessary communities.
Error Message%ROUTING-BGP-4-POLICY_EBGP [chars] operations in [chars] [chars] policy [chars] will be ignored for external neighbor/update-group [chars]
Explanation A policy attached to an eBGP neighbor performs operations that are illegal for eBGP routes, such as modifying the local-preference.
Recommended Action Modify the policy to avoid the prohibited operations.
Error Message%ROUTING-BGP-4-POLICY_IBGP [chars] operations in [chars] [chars] policy [chars] will be ignored for internal neighbor/update-group [chars]
Explanation A policy attached to an iBGP neighbor performs operations that are illegal for iBGP routes, such as modifying the AS-path or MED.
Recommended Action Modify the policy to avoid the prohibited operations.
Error Message%ROUTING-BGP-4-POLICY_NHOP_WRONGAFI The policy '[chars]' attempted to set a next-hop on [chars] with an unsuitable address type. The next-hop will not be modified.
Explanation The specified route-policy (or a policy applied by that policy) is configured - perhaps on a neighbor or for redistribution - and it is attempting to set the next-hop of the specified route to an address that doesn't match the address-family of the route. For example, it might be setting an IPv6 next-hop on an IPv4 route. Since this does not make any sense, the attempt will be ignored, and the next-hop will not be changed. (Note that this message is rate-limited, so it will not appear for every single route that is affected). Use the command 'show rpl policy name attachpoints' to determine where this policy is in use. Use the command 'show rpl policy name uses policies' to determine which other policies this policy applies (since the relevant 'set next-hop' may be in one of these policies).
Recommended Action Modify the policy so that it sets a next-hop that matches the type of route it is modifying.
Error Message%ROUTING-BGP-4-POTENTIAL_DEADLOCK Potential for deadlock detected: Locks: [chars]
Explanation BGP detected the potential for a deadlock to occur. The process will be restarted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-4-SAME_RD_SET Ignored import policy set operation for same RD import on [chars] path received from [chars]
Explanation The import policy must not perform set operations on paths, received from a PE neighbor, whose RD is the same as the RD for the importing VRF. The set operation has been ignored.
Recommended Action Modify the import policy so that it does not perform the set operation, or use globally unique RDs for VRFs.
Error Message%ROUTING-BGP-4-SPKR_RUNNING BGP AS number has changed from [chars] to [chars] - bgp (speaker) process will be restarted.
Explanation The bpm process was terminated improperly and the speaker process did not receive the notification to terminate. A new bpm process has started with a different AS number due to a new bgp configuration while the speaker process is still running with the previous AS number.
Recommended Action The speaker will be restarted to handle this error. No further corrective action is necessary. However, please contact your Cisco technical support representative to report this error.
Error Message%ROUTING-BGP-4-UNKNOWN_ACL Unknown ACL action: [unsigned int]
Explanation BGP received an unknown action (permit/deny/etc) from the ACL library
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-5-ADJCHANGE neighbor [chars] [chars]
Explanation A BGP neighbor has either come up or gone down. This message appears only if the bgp log neighbor changes command is configured for the BGP process.
Recommended Action This informational message normally appears as routers and BGP neighbors go up or down. However, unexpected neighbor loss might indicate high error rates or high packet loss in the network and should be investigated.
Error Message%ROUTING-BGP-5-BPM_ROUTER_ID No router ID available. Cannot connect to neighbors (retry in [unsigned int] seconds)
Explanation IPARM returned no valid router ID. This is due to lack of a global router ID or a loopback interface.
Recommended Action Try one of the following: 1) Set up a BGP router ID via the `bgp router-id' command in the `router bgp' configuration mode, or 2) Set up a global router ID via the `router-id' command in the global configuration mode, or 3) Set up a loopback interface with an IPv4 address.
Error Message%ROUTING-BGP-5-LOWMEM_RESET neighbor [chars] reset due to SEVERE low memory condition - use 'clear bgp [chars]' to re-enable
Explanation A SEVERE low memory condition has been encountered on the node where the BGP process is running, and so to free some memory, BGP has reset a neighbor. BGP will continue to reset neighbors periodically until the low memory condition abates. The neighbors which are reset will be shut down until a 'clear bgp' command is used to bring them back up. They will not come up automatically when the low memory condition abates - this is to prevent the node oscillating between memory states.
Recommended Action Free some memory on the system or correct the condition causing the low memory problem, and then use the 'clear bgp address' command to re-enable the neighbors that have been shut down. The 'show bgp all all summary' command can be used to easily see which neighbors are affected.
Error Message%ROUTING-BGP-5-LOWMEM_SHUTDOWN BGP is shutting down due to [chars] low memory condition - use 'process restart bgp location node' to restart
Explanation BGP received a notification that CRITICAL low memory state has been entered, or that SEVERE low memory state has been entered while BGP is in READ-ONLY mode, and consequently it has shut itself down in order to free memory.
Recommended Action Check the memory on the node, and take steps to free memory or to correct the condition which caused the low memory state. Then restart the process using the 'process restart bgp location node' command.
Error Message%ROUTING-BGP-5-MAXPFX No. of [chars] prefixes received from [chars] has reached [unsigned int], max [unsigned int]
Explanation Number of prefixes received from a neighbor for a given address family has reached the warning level configured with the 'max-prefix' command.
Recommended Action Check the prefixes received from the neighbor and verify whether the limit should be increased, or the neighbor is sending more prefixes than expected.
Error Message%ROUTING-BGP-5-NSR_STATE_CHANGE Changed state to [chars]
Explanation BGP changed its global NSR state.
Recommended Action This informational message appears when BGP changes its global NSR state.
Error Message%ROUTING-BGP-5-POLICY_RESET Policy configuration change on neighbor [chars] requires HARD reset (clear bgp [chars]) to take effect.
Explanation Automatic soft reset on policy change is not possible as the neighbor does not support ROUTE_REFRESH and 'soft-reconfiguration inbound' is not configured.
Recommended Action Manually clear affected peer at earliest convenience, in order for policy change to take effect.
Error Message%ROUTING-BGP-5-STANDBY neighbor [chars] [chars]
Explanation A BGP neighbor has gone down on standby This message appears only if the bgp log neighbor changes command is configured for the BGP process.
Recommended Action This informational message normally appears as routers and BGP neighbors go down on standby if nsr is enabled and neighbor goes down because of session flap or the replicated session on standby get torn down
Error Message%ROUTING-BGP-6-NBR_NOPOLICY No [chars] [chars] policy is configured for eBGP neighbor [chars]. No [chars] prefixes will be [chars] the neighbor until [chars] policy is configured.
Explanation No routing policy has been configured for the specified eBGP neighbor in the given direction (inbound or outbound) for the address family named. To avoid unintended routing effects, no prefixes will be accepted in that direction until some policy is configured. 'Policy' can be a route-policy, or (for inbound policy) it can be a prefix list.
Recommended Action Configure a route-policy for the neighbor in the given direction. If the desired behavior is to accept/send all routes, the route-policy should contain the single statement 'pass'. If the desired behavior is not to accept/send any routes, the route-policy should contain the single statement 'drop'.
Error Message%ROUTING-BGP-6-WARNING_WRAPPER Warning: A call to [chars] failed unexpectedly: [chars]
Explanation A function call failed unexpectedly - this is probably a system problem
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-7-BPM_CHKPT Failed to checkpoint allocation of [chars]([chars]) to speaker [unsigned int]
Explanation The BPM failed to record the allocation in the checkpoint table. This could cause operational problems if the BPM is later restarted.
Recommended Action No further action is necessary unless the BPM restarts. In that case, if problems are seen it may be necessary to deconfigure BGP completely and then reconfigure it.
C12000_IPV4_MRIB Messages
Error Message%ROUTING-C12000_IPV4_MRIB-3-INIT_ERROR Process initialization failed: ([chars]%s)
Explanation MRIB (multicast routing information base) failed to initialize. MRIB is the central routing information base for multicast components. It provides coordination among all multicast routing components and forwarding. The effect is that multicast forwarding will not function. %s - indicates the reason for the failure.
Recommended Action The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times when this error is encountered, to recover. Execute 'show process mrib' to verify that the process is up and running. If it is still non-operational, try doing 'process restart mrib' If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
C12K_MCAST Messages
Error Message%ROUTING-C12K_MCAST-3-CLEANUP_WARN [chars] - [chars] ([hex])
Explanation 'A software exception occurred during the cleanup of the c12000 ' 'multicast library.'
Recommended Action *SUPPORT*
Error Message%ROUTING-C12K_MCAST-3-ERROR [chars] - [chars]
Explanation 'A software exception occurred in c12000 multicast library'
Recommended Action *SUPPORT*
Error Message%ROUTING-C12K_MCAST-3-INIT_WARN [chars] - [chars] ([hex])
Explanation 'A software exception occurred during the initialization of the c12000 ' 'multicast library.'
Recommended Action *SUPPORT*
Error Message%ROUTING-C12K_MCAST-4-ANOMALY [chars]
Explanation 'A software exception occurred in c12000 multicast library'
Recommended Action *SUPPORT*
CLNS Messages
Error Message%ROUTING-CLNS-2-LC_INPUT Unexpected packet num [unsigned int] received on the LC
Explanation CLNS on the LC doesnot process any packet. It will ignore any packets it receives on the LC.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ASYNC_ATTACH Failed to setup ingress packet handler for NetIO: [chars]
Explanation CLNS encounted errors when initializing its connection with NetIO.
Recommended Action CLNS will restart and try to recover. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-BUNDLE_FSV_REGISTER_FAIL CLNS failed to register with packet process for bundle FSV area: [chars]
Explanation CLNS failed to register with packet manager for FSV area. It only affects the algorithm used to pick a bundle member. If no bundles are configured for ISIS - this error can be ignored.
Recommended Action If the error was seen when a packet process is restarting, then restarting NetIO will help recover from it {or} b If the error is seen in normal conditions it indicates that packet process for some reason is not able to handle the FSV registration request. Please collect the following information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. show tech-support pfi all show process packet location show process netio location show logging
Error Message%ROUTING-CLNS-3-CONFIG_INIT Cannot initialize CLNS configuration: [chars]
Explanation CLNS could not initialize its configuration mechanism, and all future CLNS configuration will fail.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-CONN_OPEN Failed to open connection for [chars]: [chars]
Explanation CLNS encounted errors when opening its connection with the process mentioned in the message. CLNS will reattempt the connection by restarting.
Recommended Action CLNS will restart and try to recover. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-DETACH Socket closing on interface [chars] failed: [chars]
Explanation The socket cannot remove an interface when closing.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-DLL_REGISTER Registration for '[chars]' failed: [chars]
Explanation Some internal initializations fail miserably!
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-EDM_CLIENT Error during operation '[chars]': [chars]
Explanation CLNS EDN client (usually a show command) failled to perform certain operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-EDM_ENCODE_FAILED Bad encoding failed for [chars]: [chars]
Explanation CLNS failed encode a bag for EDM.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-EDM_INIT Operation '[chars]' during EDM initialization failed: [chars]
Explanation CLNS show command failed to initialyze the EDM server. 'show' command will likely fail, although CLNS should be able to operate.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ERR_DEBUG_PACKET_INIT CLNS NetIO packet debugging failed to initialize.
Explanation CLNS failed to initialize packet debugging functions.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ERR_DEBUG_RETRIES_EXCEEDED Stopping CLNS debug initialization attempts after [unsigned int] tries
Explanation CLNS tried to initialize packet debugging functions but was unable to succeed even after a number of attempts. No more attempts will be made.
Recommended Action No action is required.
Error Message%ROUTING-CLNS-3-ERR_DROP_PKT [chars]. Dropping packet
Explanation CLNS encountered an internal error while trying to process a packet (usually for output). As a result CLNS dropped the packet.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ERR_INTERFACE_DATA CLNS was unable to resolve an interface while installing cap/decap chain.
Explanation CLNS was unable to look up local interface information. As a result the system may not be able to send/receive ISIS packets over this interface. This may be due to problems with either CLNS or the forwarding infrastructure.
Recommended Action Restarting the CLNS process may clear the error condition. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ERR_MEDIA_REGISTER CLNS failed to register media callback with netio: [chars]([dec])
Explanation CLNS failed to register for media callback with netio during initialization. As a result, CLNS will not be able to add its caps and wont receive or send packets. It's an internal error.
Recommended Action Restarting CLNS and/or Netio may clear the error condition. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ERR_NETIO_ENCAP_CALLBACK CLNS netio encap callback for media caps: [chars]([dec]) failed [chars]([dec])
Explanation CLNS failed to setup encap callback with this particular media or base capsulation. As a result CLNS will not be able to receive CLNS packets on this caps on any interface on this node.
Recommended Action Restarting CLNS and/or Netio may clear the error condition. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ERR_NETIO_SET_MAPPING CLNS netio set mapping for media caps: [chars]([dec]) failed [chars]([dec])
Explanation CLNS failed to setup mapping with this particular media or base capsulation. As a result CLNS will not be able to receive CLNS packets on this caps on any interface on this node.
Recommended Action Restarting CLNS and/or Netio may clear the error condition. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ERR_PARTNER_LOOKUP CLNS-NetIO partner lookup failed
Explanation NetIO was unable to initialize the CLNS partner process. As a result the system will not be able to send/receive ISIS packets over interfaces on this line card.
Recommended Action Restarting CLNS and/or NetIO may clear the error condition. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ERROR_INIT Cannot register CLNS error codes: [chars]
Explanation CLNS could not initialize its error code. CLNS will work, but error messages won't be user friendly!
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ETHERENCAP Incorrect MAC address length [dec]
Explanation The MAC address length provided for the ethernet encapsulation is wrong.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-EVENT_CONN_CREATE_FAIL Error creating '[chars]' connection: [chars]
Explanation CLNS failed to create a connection to an essential service during initialization. This is an internal error. It requires a restart of the process for recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-EVENT_CONN_NOTIFY_FAIL Error registering for critical events on '[chars]' connection: [chars]
Explanation During initialization, CLNS failed to register for essential notifications regarding the state of the connection for the specified service. This is an internal error. It requires a restart of the process for recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-EVM_INIT Error while initializing the [chars]: [chars]
Explanation An operation failed during the initialization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-GET_TRAFFIC Cannot get traffic information: [chars]
Explanation CLNS show command failed to get the required information.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-HSSD_REGISTER_FAIL CLNS failed to register for an HSSD area: [chars]
Explanation CLNS failed to register for an HSSD area. This is an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-INTERFACE Operation '[chars]' on CLNS interface [chars] failed: [chars]
Explanation CLNS could not initialize its interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-L2INFO_LEN [chars] length is [dec], should be [dec]
Explanation The length of the L2 data received is not what it should be.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-LPTS_ADD_BINDING Couldn't add clns binding to lpts port arbitrator, error equals [chars]
Explanation The clns process was unable to add a binding to LPTS. This is an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-LPTS_DELETE_BINDING Couldn't delete CLNS binding from Port Arbitrator, result equals [chars]
Explanation The clns process was unable to delete a binding from LPTS. This is an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-LPTS_SETOPT Cannot set the LPTS option '[chars]': [chars]
Explanation An operation failed during LPTS option setting.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-PAK Packet operation '[chars]' failed: [chars]
Explanation An operation failed during packet handling.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-PAK_READ Failed to read data from packet area: [chars]
Explanation The clns process was unable to read the input packet. This is an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-PFI_INIT_FAILED PFI Initialization failed: [chars]
Explanation An operation failed during the Packet Forwarder Interface initialization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-SEND_ASYNC CLNS was unable to wake itself up([dec]) for reading pending packets: [chars]
Explanation CLNS is unable to wake up itself to read the pending ingress packets from NetIO. ISIS will not be able to receive these pending packets from CLNS.
Recommended Action Restarting CLNS might help. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-SOCK_INIT Socket initialisation task '[chars]' failed: [chars]
Explanation An operation failed during socket initialisation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-SOCK_SET_NAME Internal socket error on packet reception: [chars]
Explanation An operation failed during packet reception.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-SOCKET_PARSE_PATH error encountered when parsing path: [chars]
Explanation CLNS was unable to extract the xipc & job id from the socket path. This might cause communication problems between ISIS and CLNS.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-SOCKET_RESMGR_ATTACH Failed to setup the clns socket as a resource manager: [chars]
Explanation The clns process failed to advertise itself to the system as a resource manager.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-STATSD_INIT Cannot connect to the stats server: [chars]
Explanation An operation failed during the Stats Server Connection opening.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-STATSD_REGISTER Cannot [chars] with the stats server for interface CH[hex] ([hex])
Explanation An operation failed during the Stats Server Interface registration.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-THREAD_CREATE Error starting thread for [chars] processing : [chars]
Explanation CLNS failed to create the thread for the operation mentioned in the message. CLNS will try to recover by restarting.
Recommended Action CLNS will try to recover by restarting. If it recovers no further action is needed. This error is not expected and very rare. It is usually seen when system resources like memory are very low. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-TIMESTAMP Operation '[chars]' failed during packet timestamping: [hex] ([chars])
Explanation An operation failed during timestamp processing.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-BASE_CAPS_LU_FAIL IM base capsulation lookup for interface CH[hex] ([hex]) failed: [hex], '[chars]'
Explanation The Interface Manager returned an unexpected error when CLNS attempted to lookup an interface's base capsulation type. This may be a resource problem but is probably an internal error.
Recommended Action Consider restarting the CLNS and/or Interface Manager processes. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-DEBUG_REGISTER_FAIL Failed to register with the debugging subsystem: [hex], '[chars]'
Explanation CLNS failed to register with the debugging subsystem. If this message has been generated then CLNS debugging may not be available. This may be a system resource problem.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-ERR_CONN_SETRETRY Error setting the linear retry period for '[chars]': '[chars]'
Explanation CLNS failed to set the linear retry period for connecting to sysdb. We set the retry period in order to avoid immediate reconnection attempt from clns to sysdb server when the latter restarts. This prevents clns from blocking on sysdb and cause any traffic drop.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-ERR_IDB_LOOKUP_DROP_PKT [chars]: Netio IDB not found for interface CH[hex] ([hex]), packet 0x[pointer] dropped
Explanation CLNS was unable to find the NetIO IDB for the interface handle in the message. If this is seen during NetIO restart, it could be transient condition that should recover once NetIO is back up with all the IDBs in steady state. If this is seen in steady state, the ISIS adjacency on this interface could be affected. *RECUR*
Recommended Action If this message is seen during NetIO restarts and the message is seen only at that time, no further action is needed. If this message is seen during steady state more than once with the ISIS adjancency on this interface being affected, restarting netio process or improxy process might help in redownloading the IDBs to netio.
Error Message%ROUTING-CLNS-4-GET_MCASTADDR_ERR Failed to get MAC address(im_attr_macaddr_get) for [chars]: [chars]
Explanation The process failed to get MAC address from the interface. This can be caused by a faulty hardware.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-IM_CRE_REG_FAIL CLNS interface registration failed for base cap type [chars]: [chars]
Explanation CLNS process failed to register an interface with the Interface Manager. This is an internal error. It requires a restart of process for recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-IM_SERV_BIND_FAIL Failed to bind to the Interface Manager: [dec]
Explanation CLNS failed to bind to the Interface Manager control plane. It's an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-IM_SIGEVENT_FAIL IM control handler setup failed: [chars]
Explanation CLNS failed to establish signal event in the Interface Manager control plane. It's an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-MAC_SIZE_ERR Incorrect MAC address size for [chars] (returned: [dec], expected: [dec])
Explanation MAC address size does not match IEEEBYTES (6 bytes). This can be caused by a faulty hardware.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-NETIO_OUTPUT_FAIL Failed to send packet 0x[pointer] to NetIO on interface CH[hex] ([hex]): [chars]
Explanation CLNS was not able to send a packet to NetIO. This could be because of communication problems between CLNS and NetIO.
Recommended Action If this message is seen during transient conditions, for example when NetIO is restarting either because of install operation OR because NetIO crashed then it is not harmful unless you see ISIS adjacencies dropping. If it is seen under steady state conditions OR If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-PAK_FROM_ISIS_FAIL Failed to process packet 0x[pointer] from ISIS: [chars] [chars]
Explanation CLNS was not able to process a packet from ISIS successfully and hence dropped the packet.
Recommended Action This message could be seen under low packet memory conditions and should recover once packet memory becomes available to CLNS. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-PAK_FROM_NETIO_FAIL Failed to process packet 0x[pointer] from NetIO: [chars]:[chars]
Explanation CLNS was not able to process a packet from NetIO successfully and hence dropped the packet.
Recommended Action This message could be seen under low packet memory conditions and should recover once packet memory becomes available to CLNS. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-SEND_HELLO_PDU_TO_ISIS_FAIL Failed to send Hello PDU(0x[pointer]) type [chars] ([hex]) from interface CH[hex]([hex]) to ISIS instance [chars]: [chars]
Explanation CLNS was not able to send a hello class PDU to ISIS. This could be because of communication problems between CLNS and ISIS.
Recommended Action If this message is seen during transient conditions, for example when ISIS is restarting either because of install operation OR because ISIS crashed then it is not harmful. If the error message says out of memory, it is because of the queue between CLNS and ISIS being FULL which could either be because traffic rate is very high or ISIS might not be reading the packets. If it is seen under steady state conditions OR adjacency flaps are seen on this interface OR If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-SEND_PDU_TO_ISIS_FAIL Failed to send PDU(0x[pointer]) type [chars] ([hex]) from interface CH[hex]([hex]) to ISIS instance [chars]: [chars]
Explanation CLNS was not able to send non-Hello class PDU to ISIS. This could be because of communication problems between CLNS and ISIS.
Recommended Action If this message is seen during transient conditions, for example when ISIS is restarting either because of install operation OR because ISIS crashed then it is not harmful. If the error message says out of memory, it is because of the queue between CLNS and ISIS being FULL which could either be because traffic rate is very high or ISIS might not be reading the packets. If it is seen under steady state conditions OR If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-TRACE_INIT_FAIL Failed to init debug tracing support : [chars]
Explanation CLNS failed to init with the ltrace subsystem. This affects the debuggability of the component. CLNS will attempt to restart to recover from the situtation.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-UNKNOWN_MEDIA Unknown media ([dec]) on interface CH[hex] ([hex])
Explanation The specified interface media is not supported by CLNS. This means that IS-IS and other CLNS protocols cannot run over the specified interface. This is an internal programming error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.. As a workaround consider using a different encapsulation for the interface.
Error Message%ROUTING-CLNS-7-CAPS_ADD_FAIL Failed to add CLNS encapsulation to interface CH[hex] ([hex]): [chars]
Explanation CLNS failed to add caps to its encapsulation chain. It's an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-7-CONN_PAK_AREA_FAIL CLNS failed to connect to packet area
Explanation CLNS failed to connect to packet subsystem during initialization. As a result, CLNS will not be able to receive or send packets. It's an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-7-DEBUG_THREAD_CREATE Error starting thread for debug registration: [dec]
Explanation CLNS failed to create the thread for debug registration and to handle debug events. Thus, causing unavailability of debugs. But CLNS should continue with the normal functionality, so the process should not exit even if this thread is not created.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-7-ERR_L2_HASH CLNS failed to initialize the L2 hash function: [chars]
Explanation CLNS failed to initialize the L2 hash function. It's an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-7-ERR_STACKMEM Could not alloca [dec] bytes
Explanation CLNS failed to allocate stack memory space.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-CLNS-7-IM_ATTR_REG_FAIL Failed to register for notification of MAC address: [chars]
Explanation An error was discovered during the Interface Manager MAC address registration. It requires a restart of process for recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
DAD Messages
Error Message%ROUTING-DAD-3-ERR_EVM_ASYNC_ATTACH Unable to listen for events because: [chars]
Explanation A failure occured while trying to setup the event listen structure for package un-installs.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-DAD-3-ERR_SYSDB_BIND Sysdb bind operation failed because: [chars]
Explanation The bind operation has failed for the above reason. This is something that should not occur under normal operations.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-DAD-3-ERR_SYSDB_DELETE Sysdb delete operation failed because: [chars]
Explanation The DAD library attempts to delete the old protocol information before writing out the new information. This delete operation failed for the above reason.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-DAD-3-ERR_SYSDB_SET The writing of sysdb information failed because: [chars]
Explanation The DAD library encountered an error while writing out the policy information for the above reason.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-DAD-3-ERR_SYSMGR_PROC_AVAILABLE Unable to declare proc available because: [chars]
Explanation A failure occured while trying to tell sysmgr that we are available for availability.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-DAD-3-ERR_SYSMGR_PROC_CLEANUP Unable to listen for cleanup notices because: [chars]
Explanation A failure occured while trying to ask sysmgr for cleanup events for package un-installs.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-DAD-3-ERR_SYSMGR_PROC_READY Unable to declare proc ready because: [chars]
Explanation A failure occured while trying to tell sysmgr that we are ready for processing.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-DAD-7-SETUP Invalid setup at [chars]@[dec]: [chars]
Explanation There was something illegal about the setup operations that where performed. This should be a straight coding error that will fail everytime and should be cleaned up before releasing the code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
EIGRP_POLICY Messages
Error Message%ROUTING-EIGRP_POLICY-3-ORA_INSTBUILD Failed to build [chars]: [chars] ([chars])
Explanation Internal error in the routing policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EIGRP_POLICY-3-ORA_ORABUILD Failed to build ORA[chars]: [chars] ([chars])
Explanation There was an internal error in the routing policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EIGRP_POLICY-3-ORA_RUN Could not apply policy operation [chars] to attribute [chars] because [chars]
Explanation Internal error in the routing policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
EIGRP Messages
Error Message%ROUTING-EIGRP-2-ERR_MEM_ALLOC [chars] [dec]: Could not allocate memory for [chars]
Explanation There is not enough memory available for the EIGRP process.
Recommended Action This indicates a low-memory condition. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-EIGRP-3-ANCHORCOUNT [chars] [dec]: Anchor count negative
Explanation Internal error in the flow control module in EIGRP.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EIGRP-3-BADCOUNT Invalid path count for route [chars], [dec] successors, [dec] paths
Explanation A bad reference count has been detected while adding a path for a prefix.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EIGRP-3-INTERNAL [chars] [dec]: [chars]
Explanation An internal error occured in EIGRP.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EIGRP-3-MULTIFLOW Flow control error, [chars], on [chars]
Explanation Error in the flow control algorithm in EIGRP.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EIGRP-3-NOBUFFER No buffers available for [unsigned int] byte packet
Explanation EIGRP could not allocate a packet buffer to transmitting a packet.
Recommended Action The number of packet buffers available for transmitting EIGRP packets is low. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*
Error Message%ROUTING-EIGRP-3-PAK_WRITE Failed to construct packet to send on [chars]. [chars]
Explanation Error in constructing a packet, to be transmitted by EIGRP.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EIGRP-3-PEERSEXIST [dec] peers exist on [chars]
Explanation One or more peers exist on an interface which is being deleted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EIGRP-3-PFXLIMIT [chars] [dec]: [chars] prefix limit reached
Explanation 'Number of prefixes for eigrp has reached the configured ' 'or default limit.'
Recommended Action 'Use 'show ip eigrp accounting' for details on the source ' 'of the prefixes and take corrective measures.'
Error Message%ROUTING-EIGRP-3-RDBLEFT Interface removed, but route [chars], nexthop [chars] ([chars]), origin [chars], has path
Explanation Routes exist over an interface being deactivated.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EIGRP-3-REFCOUNT Negative refcount in packet descriptor 0x[pointer]
Explanation Internal reference count error in EIGRP.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EIGRP-3-SIA Route [chars] stuck-in-active state in instance [dec]. Cleaning up
Explanation Neighborship was reset to the specified peer, due to a prefix being in stuck-in-active state.
Recommended Action Verify that there are no packet drops between the neighbors and the state of the EIGRP prefix in the neighbor. Clear the eigrp neighbor. If the CPU utilization by EIGRP remains high, restart the EIGRP process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EIGRP-3-UNKTIMER Unknown timer type [dec] expiration
Explanation Unknown timer encountered in EIGRP.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EIGRP-4-ERR_SOCKET Error [chars]setting [chars] option in [chars]
Explanation EIGRP was unable to set the specified socket option on the specified interface or VRF.
Recommended Action If the message persists, remove and readd the affected interface or VRF and if the problem still persists, restart EIGRP process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EIGRP-4-PFXLIMITTHR [chars] [dec]: [chars] threshold prefix level reached
Explanation 'Number of prefixes in the topology database has reached ' 'the configured or default threshold level.'
Recommended Action 'Take preventive action by identifying the source of ' 'the prefixes. Use 'show ip eigrp accounting' ' 'for details.'
Error Message%ROUTING-EIGRP-4-WARNING [chars]
Explanation There is a subnet mismatch between eigrp neighbors.
Recommended Action Verify the primary IPv4 address on both ends of the specified interface.
Error Message%ROUTING-EIGRP-5-NBRCHANGE [chars] [dec]: Neighbor [chars] ([chars]) is [chars]: [chars]
Explanation An EIGRP neighbor has gone UP or DOWN.
Recommended Action No action is required.
Error Message%ROUTING-EIGRP-6-EVENT [chars], [chars]
Explanation An EIGRP event logged into the trace buffer.
Recommended Action No action is required.
Error Message%ROUTING-EIGRP-6-PAK_SEND Failed to send packet on [chars]. [chars]
Explanation Failed to send a packet from EIGRP.
Recommended Action This can happen if other processes involved in packet forwarding are restarting. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
FIB Messages
Error Message%ROUTING-FIB-2-IFH_RECYCLE_CLEANUP_EXT_FAIL IFH-RECYCLE: Quarantined idb extension(0x[pointer])(proto [chars]) for interface [hex] not cleaned up - flags - [hex], ref-count - [dec], nh count - [dec], glean nhinfo 0x[pointer]. Detailed info dump at - [chars]
Explanation FIB tried to cleanup an idb on detecting ifhandle recycle to a new interface. However, that failed for some reason.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-INIT FIB initialization failure: [chars] [chars]
Explanation FIB initialization failed
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-INVALID_MSG FIB thread [chars] received an invalid message: [chars] [unsigned int]
Explanation FIB thread got an invalid message so it is exiting
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-OOR CEF has run out of [chars] resource memory. No more route updates will be handled by the CEF. Please delete routes, and then clear the cef on this node to resume normal operation
Explanation The fib_mgr process on the node has detected an out of resource condition for the indicated resource. Normal operation cannot resume until routes are deleted and customer does a clear cef on the node.
Recommended Action Run show cef resource command and check which resource(s) are running low on memory. Significant routes will have to be deleted followed by a clear cef on the affected node to resume normal cef operation.
Error Message%ROUTING-FIB-2-OOR_TBL CEF has run out of table resource memory. This table [hex] could not be created. Please check the memory on the card and then recreate/reconfigure the table when enough memory is available
Explanation The fib_mgr process on the node has detected an out of resource condition for the indicated resource. Normal operation cannot resume until routes/tables are deleted and customer does a recreate of the table.
Recommended Action Run show cef resource command and check which resource(s) are running low on memory. Significant routes/tables will have to be deleted followed by a reconfiguration of the table.
Error Message%ROUTING-FIB-2-PROTO_INIT FIB [chars] protocol initialization failure: [chars] [chars] ([unsigned int])
Explanation FIB initialization failed
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-SHMRESET resetting shared memory for [chars]
Explanation FIB Mgr has crashed repeatedly that exceeds threshold, resetting the shared memory.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-STATE FIB startup state [chars] failure: [chars] [unsigned int]
Explanation FIB initialization failed
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-THREAD_INIT FIB thread [chars] initialization failure: [chars] [chars] ([unsigned int])
Explanation FIB initialization failed
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-ADJ_INIT FIB initialization with the AIB failed [chars]: [chars]
Explanation An internal software error occurred that prevented the FIB from working with AIB.
Recommended Action Try restarting the fib process to see if the route gets programmed again. LC OIR can be tried as well.
Error Message%ROUTING-FIB-3-ATTRIBUTE Attribute operation failed during [chars]: for [chars] ([dec], [chars])
Explanation An internal software error occurred that prevented the FIB from working with attributes.
Recommended Action Try restarting the fib process to see if the problem goes away.
Error Message%ROUTING-FIB-3-BCDL BCDL failed during [chars] for group [chars]: [chars]
Explanation An internal software error occurred that prevented the FIB from working properly with BCDL.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-CLIENT_ERROR [chars] [chars]
Explanation A FIB client behaved erroneously or there was an unexpected state.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-DEFAULT_ROUTE_CREATE_FAIL Default rolute creation failed [chars]
Explanation A route update was skipped because of an internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-DUMMY_ZERO_ERR Error while attempting to restore dummy real zero: [hex] [chars]
Explanation Cannot restore the dummy real zero route to its original state
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-DUMMY_ZERO_REMOVE Removing ing dummy real zero because of error: [hex] [chars]
Explanation Forced to delete because cannot restore the dummy real zero because of error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-GEN_ERR FIB internal error: [chars]
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-GTRIE GTRIE failed during [chars]: [chars]
Explanation An internal software error occurred that prevented the FIB from working with the tries.
Recommended Action Try restarting the fib process to see if the problem goes away.
Error Message%ROUTING-FIB-3-IDB IDB operation for ifh:[hex] failed during [chars]: ([dec], [chars])
Explanation An internal software error occurred for an IDB action.
Recommended Action Try restarting the fib process to see if the problem goes away.
Error Message%ROUTING-FIB-3-INIT_GR_EXIT_TOUT Timed-out on graceful exit for init failure, exiting ungracefully
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-INTERNAL_ERR An internal processing error/illegal state detected
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-LCL_ATTRIB_MAX_REACHED Local attribute index database max([dec]) reached
Explanation The local attribute index database on the LC has reached its max.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-LEAF_DEPEND_CLEANUP_ERR LEAF-DEL-ERR: All dependents of leaf [pointer] did not unlink, leaf-ref-count:[dec] first-dep:[pointer]
Explanation This is an unexpecetd state where after leaf deletion, leaf still has some dependent paths pointing to it. This could prevent the leaf from getting freed
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-MALLOC_FAILED Heap memory allocation failed from - '[chars]'
Explanation FIB couldn't allocate memory for some internal processing. It might be in consistent state.
Recommended Action Check memory utilization on the card the error came for and take appropriate steps to reduce it.
Error Message%ROUTING-FIB-3-PD_FAIL [chars]
Explanation This is a catch all PD errors.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-PFI_FIB_IFTYPE_MISMATCH Mismatch in interface type [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-PLATF_UPD_FAIL Platform upd failed: Obj equals [chars][ptr equals [pointer],refc equals [hex],flags equals [hex]] Action equals [chars] Proto equals [chars]. Cerr equals [chars]
Explanation This is a catch all Platform update errors during development phase.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-RCC_NO_TABLE route check to the fib failed table [hex], protocol [chars]: [chars]
Explanation An internal software error occurred that prevented the FIB from completing the route check.
Recommended Action Try restarting the fib process to see if the route gets programmed again. LC OIR or clear route * can be tried as well.
Error Message%ROUTING-FIB-3-RECURSIVE_LOOP [chars]
Explanation This is to catch recursive loops.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-RETRY retry module failed [chars]: [chars]
Explanation An internal software error occurred that prevented the FIB from retrying a failed operation.
Recommended Action Try restarting the fib process to see if the route gets programmed again. LC OIR or clear route * can be tried as well.
Error Message%ROUTING-FIB-3-ROUTE route update for [chars] (table [hex]) to the fib failed [chars]: [chars]
Explanation An internal software error occurred that prevented the FIB from working with route updates.
Recommended Action Try restarting the fib process to see if the route gets programmed again. LC OIR or clear route * can be tried as well.
Error Message%ROUTING-FIB-3-ROUTE_GEN [chars]: [chars]
Explanation An internal software error occurred during route handling.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-SHM shared memory failed during [chars]: [chars]
Explanation An internal software error occurred that prevented the FIB from working properly with shared memory.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-TABLE table operation failed during [chars]: [chars]
Explanation An internal software error occurred that prevented the FIB from working with multiple tables.
Recommended Action Try restarting the fib process to see if the problem goes away.
Error Message%ROUTING-FIB-3-TE_CREATE_ERR TE-CREATE-ERROR: [chars]
Explanation An error occurred during TE programming
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-TE_DESTROY_ERR TE-DESTROY-ERROR: [chars]
Explanation A te-tunnel created with DOWN backup was destroyed
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-TIMER Timer module failed [chars]: [chars]
Explanation An internal software error occurred that prevented the FIB handling timers.
Recommended Action Try restarting the fib process to see if the route gets programmed again. LC OIR or clear route * can be tried as well.
Error Message%ROUTING-FIB-4-PFI_IFH_CONN fail to connect to PFI_IFH [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-PULSE_HNDLR FIB received unidentifiable pulse: proto [unsigned int], opc [unsigned int], [chars]
Explanation FIB received a pulse that could not be identified.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-RSRC_LOW CEF running low on [chars] resource memory. CEF will now begin resource constrained forwarding. Only route deletes will be handled in this state, which may result in mismatch between RIB/CEF. Traffic loss on certain prefixes can be expected. The CEF will automatically resume normal operation, once the resource utilization returns to normal level
Explanation The fib_mgr process has detected that average utilization for specified resource has risen above a predefined high watermark value, and has enterred resource contrained forwarding mode. In this mode, the cef will only handle route deletes which may potentially freeup some memory. Due to this operational mode, the CEF/RIB will be out of sync. Once routes are deleted and resource utilization level drops to acceptable levels again, cef will come out of this operational mode and resume normal operation.
Recommended Action Run show cef resource command and check which resource(s) are running low on memory. Any action that reduces number of routes for this protocol (results in route delete events to free up resources below predefined level) will eventually result in the cef returning to normal operation after few seconds.
Error Message%ROUTING-FIB-5-ROUTE_UPDATE_DROP [chars]
Explanation An internal software error occurred and FIB had to throw away a route update
Recommended Action Try restarting the fib process to see if the problem goes away.
Error Message%ROUTING-FIB-6-DEPEND_UNBIND_FAILURE Unbind for object type [chars] failed from parent type [chars] - no unbind handler found
Explanation FIB internal APIs need/expect an unbind handler, which wasn't found. This can lead to FIB not cleaning up state on interface delete events.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-6-HARD_RESET [chars]
Explanation FIB is restarting with a reset of it's shared memory to possibly recover from an unrecoverable state
Recommended Action None
Error Message%ROUTING-FIB-6-RSRC_OK CEF resource state has returned to normal. CEF has exited resource constrained operation and normal forwarding has been restored
Explanation The fib_mgr process had previously detected that the hardware,software resources required for cef operation were running low, and had enterred resource constrained forwarding. Now resources have been restored and cef has resumed normal operation.
Recommended Action None.
FWD_HA Messages
Error Message%ROUTING-FWD_HA-4-PROCESS_RESTART [chars] restart_count equals [dec] mode equals [dec] ([chars])
Explanation The process is being restarted either because we failed to initialize or we finished resetting shared memory and we are starting fresh.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
HFR_IPV4_MRIB Messages
Error Message%ROUTING-HFR_IPV4_MRIB-3-CHKPT_ERR Failed to [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-CHKPT_ERR Failed to [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-FGID_ADD_ERR Failed to add LC [dec] into FGID [dec]: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-FGID_ADD_ERR Failed to add LC [dec] into FGID [dec]: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-FGID_BATCH_ADD_ERR Failed to add batch of LCs into FGIDs: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-FGID_BATCH_ADD_ERR Failed to add batch of LCs into FGIDs: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-FGID_BATCH_REMOVE_ERR Failed to remove batch of LCs from FGIDs: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-FGID_BATCH_REMOVE_ERR Failed to remove batch of LCs from FGIDs: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-FGID_ERR Failed to [chars]: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-FGID_ERR Failed to [chars]: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-FGID_REMOVE_ERR Failed to remove LC [dec] from FGID [dec]: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-FGID_REMOVE_ERR Failed to remove LC [dec] from FGID [dec]: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-IFH_ERR Failed to [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-IFH_ERR Failed to [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-IM_NAME_ERR im_interface_name error in function [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-IM_NAME_ERR im_interface_name error in function [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-INTERNAL_ERR Failed to [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-INTERNAL_ERR Failed to [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-INVALID_FGID_ERR Failed to [chars] : invalid fgid value [hex]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-INVALID_FGID_ERR Failed to [chars] : invalid fgid value [hex]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-MEM_ERR Failed to [chars] for [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-MEM_ERR Failed to [chars] for [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-PERF_ERR Failed to [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-PERF_ERR Failed to [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IGMP_MTRACE Messages
Error Message%ROUTING-IGMP_MTRACE-3-EVENT_ERROR Event error: [chars] in [chars]
Explanation Event error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IGMP_MTRACE-3-INIT_ERROR Init error: [chars]
Explanation Initialisation error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IGMP_MTRACE-3-MEMORY_ERROR Memory error: [chars] in [chars]
Explanation Memory error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IGMP_MTRACE-3-MSG_ERROR msg error: [chars] in [chars]
Explanation Messaging error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IGMP_MTRACE-3-SOCKET_ERROR Socket error: [chars] in [chars] : [chars]
Explanation Socket error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IGPTE_LIB Messages
Error Message%ROUTING-IGPTE_LIB-3-ERR_BAG_REGISTER Error registering igpte-lib [chars] bags: [hex], '[chars]'
Explanation IGP failed to register its bag files with the bag library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IGPTE_LIB-3-ERR_DBG_REGISTER Error registering for IGP debug events: [hex], '[chars]'
Explanation IGP failed to register with the debug module for printing messages.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IGPTE_LIB-3-ERR_SYSDB_BIND Failed to bind to SysDB: error [hex] ([chars])
Explanation An error occurrred when accessing the system database
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. The process must be restarted before it can function correctly.
Error Message%ROUTING-IGPTE_LIB-3-ERR_SYSDB_REG_NOTIFY Failed to register for [chars] notifications: error [hex] ([chars])
Explanation An error occurrred when accessing the system database
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. The process must be restarted before it can function correctly.
Error Message%ROUTING-IGPTE_LIB-3-ERR_SYSDB_UNREG_NOTIFY Failed to unregister for [chars] notifications: error [hex] ([chars])
Explanation An error occurrred when accessing the system database
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. The process must be restarted before it can function correctly.
Error Message%ROUTING-IGPTE_LIB-4-CLIENT_ERR_MEM_ALLOC Failed to allocate [unsigned int] bytes for '[chars]'
Explanation The process failed to allocate memory for the specified resource.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration..
Error Message%ROUTING-IGPTE_LIB-4-DATA_QUEUE_FULL message queue is full. Cannot accept more element.
Explanation Data queue is full and it cannot accept more element. It could be a result of memory limitation.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration..
Error Message%ROUTING-IGPTE_LIB-4-ERR_MEM_ALLOC Failed to allocate [unsigned int] bytes for '[chars]'
Explanation The process failed to allocate memory for the specified resource. This could be because the topology is too large for the memory installed in the router.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration..
Error Message%ROUTING-IGPTE_LIB-4-INVALID_TLV Data ([dec]) is too big or small([dec])
Explanation Failed to send data due to the limitation of the buffer size. This is an internal error. It requires to reduce the number of interfaces.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration..
Error Message%ROUTING-IGPTE_LIB-4-SERVER_ERR_CLINFO_HOLD Error in saving client's message channel information
Explanation IGP failed to save its client's message channel information. This could be a result of channel down or resource allocation failure.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration..
Error Message%ROUTING-IGPTE_LIB-4-SERVER_ERR_CLINFO_UNHOLD Error in releasing client's message channel information
Explanation IGP failed to release its client's message channel information. This could be a result of channel down already.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration..
IP_STATIC_BFD_SESSMGR Messages
Error Message%ROUTING-IP_STATIC_BFD_SESSMGR-4-UNSUPPORTED_INTERFACE : [chars]
Explanation The nexthop is resolved over an unsupported BFD interface.
Recommended Action Pick different nexthop to create the BFD session.
IP_STATIC Messages
Error Message%ROUTING-IP_STATIC-3-IDB_DELETE Failed to delete idb for interface [chars] from '[chars]' thread
Explanation The static routing process failed unexpectedly to delete an interface descriptor block from the idb WAVL tree.
Recommended Action *SUPPORT*
Error Message%ROUTING-IP_STATIC-3-INTERNAL [chars]: [chars]
Explanation The static routing process has either failed a function that expected to succeed, or has got into an inconsistent state.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-ITAL_EVENT Error processing [chars] event for [chars] from ITAL, table [hex] : [chars]
Explanation A static routing process failed unexpectedly when processing an IP address change event. This may lead to spurious or missing connected and local routes in the routing table.
Recommended Action *RECUR*
Error Message%ROUTING-IP_STATIC-3-ITAL_INTERFACE_CREATE Error handling create event for interface [chars]: [chars]
Explanation The static routing process failed to correctly handle a create event for an interface which it was tracking.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-ITAL_TDB_REGISTER_FAILED A static routing process failed function ip_static_ital_vrf_register for table [chars]: [chars]
Explanation A static routing process failed to register a table with ITAL. This may lead to routes associcated with a the failed to be added in the routing table.
Recommended Action *RECUR*
Error Message%ROUTING-IP_STATIC-3-NHDB_DELETE Failed to delete nhdb for next-hop [chars] for table [hex]
Explanation The static routing process failed unexpectedly to delete an next-hop descriptor block from the nhdb AVL tree.
Recommended Action *SUPPORT*
Error Message%ROUTING-IP_STATIC-3-PATH_BP_DELETE Failed to delete backpointer to path [chars]/[unsigned int] from [chars] [chars]
Explanation The static routing process failed unexpectedly to delete a path from an interface or next-hop descriptor block's path backpointer list.
Recommended Action *SUPPORT*
Error Message%ROUTING-IP_STATIC-3-RIB_BATCH [chars]: Failed to send RIB batch buffer re-populating RIB for table [hex]: [chars]
Explanation The static routing process failed unexpectedly to update RIB with a batch of updates.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-RIB_CLEAR_PREFIX Error re-installing route after a clear table event for prefix [chars]/[unsigned int] in table [hex]: [chars]
Explanation There was an error re-installing a route in the RIB after receiving a 'clear prefix' event.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-RIB_CLEAR_TABLE Error re-installing routes after a clear table event for table [hex]: [chars]
Explanation There was an error re-installing routes in the RIB after receiving a 'clear table' event.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-RIB_CLEAR_UNKNOWN_PREFIX Received a clear event for unknown prefix [chars]/[unsigned int] in table [hex]
Explanation The static routing process received a clear event from RIB for a prefix which it was not tracking.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-RIB_CLEAR_UNKNOWN_TABLE Received a clear event for unknown table [hex] (Prefix [chars])
Explanation The static routing process received a clear event from RIB for a table which it was not tracking.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-RIB_ECMP Failed to update RIB after ECMP recalculation for table [hex], prefix [chars]/[unsigned int]: [chars]
Explanation The static routing process failed unexpectedly to update RIB after an ECMP recalculation.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-RIB_FETCH Error fetching event from RIB: [chars]
Explanation The static routing process failed unexpectedly to fetch a notification event from RIB.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-RIB_FULL Failed to update RIB during full topology download for table [hex], prefix [chars]/[unsigned int]: [chars]
Explanation The static routing process failed unexpectedly to update RIB after RIB restarted.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-RIB_INTERFACE Failed to update RIB for table [hex], prefix [chars]/[unsigned int], after receiving interface state event for [chars]: [chars]
Explanation The static routing process failed unexpectedly to update RIB after an interface state change event.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-RIB_NEXTHOP Failed to update RIB for table [hex], prefix [chars]/[unsigned int] after receiving next-hop resolution event for [chars]: [chars]
Explanation The static routing process failed unexpectedly to update RIB after a next-hop resolution event.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-RIB_NEXTHOP_REGISTER Failed to register next-hop notification with RIB for table [hex], prefix [chars]: [chars]
Explanation The static routing process failed unexpectedly to register a next-hop resolution event. Future state change events on the next-hop may cause further messages to be generated by the static process.
Recommended Action *SUPPORT*
Error Message%ROUTING-IP_STATIC-3-RIB_NEXTHOP_UNREGISTER Failed to unregister next-hop notification with RIB for table [hex], prefix [chars]: [chars]
Explanation The static routing process failed unexpectedly to unregister a next-hop resolution event. Future state change events on the next-hop may cause further messages to be generated by the static process.
Recommended Action *SUPPORT*
Error Message%ROUTING-IP_STATIC-3-RIB_TOO_MANY_PATHS Prefix [chars]/[dec]: Maximum path count exceeded. Please remove (next-hop [chars], interface [chars]) from the running configuration.
Explanation The maximum allowed number of next-hop paths for a single destination prefix has been exceeded. One or more paths have not been installed in the RIB, and should be removed from the running configuration.
Recommended Action Excess next-hop paths should be removed from the running configuration.
Error Message%ROUTING-IP_STATIC-3-SHUTDOWN Process is shutting down: [chars]
Explanation The static routing process has performed a graceful shutdown and will be restarted.
Recommended Action Check to make sure the process has restarted. If not, restart manually Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-TDB_DELETE Failed to delete tdb for table [hex]'
Explanation The static routing process failed unexpectedly to delete a table descriptor block from the tdb AVL tree.
Recommended Action *SUPPORT*
Error Message%ROUTING-IP_STATIC-3-TDB_REGISTER_FAILED A static routing process failed function ip_rib_protocol_register for table [hex]: [chars]
Explanation A static routing process failed to register a table with RIB. This may lead to routes associcated with a the failed to be added in the routing table.
Recommended Action *RECUR*
Error Message%ROUTING-IP_STATIC-3-UPDATE_COMPLETE Failed to send 'update complete' notification to RIB for table [hex]: [chars]
Explanation The static routing process unexpectedly failed an attempt to signal to the RIB that the given table is now in sync
Recommended Action Check the routing table to see whether any static routes are missing, and whether the protocol is in sync. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-6-CONFIG_MAXIMUM_CHANGE The maximum number of configurations for static routes has been changed from [unsigned int] to [unsigned int]
Explanation The maximum number of static route configurations which may be entered has been changed.
Recommended Action Refer to the configuration guidelines for the maximum allowed limit for static routes
Error Message%ROUTING-IP_STATIC-6-NHDB_LOCAL The next-hop [chars] for table [hex] is a local route. The static route(s) that has the matching next-hop will not be installed.
Explanation The nexthop of a static route is a local route. This is an invalid configuration.
Recommended Action *SUPPORT*
Error Message%ROUTING-IP_STATIC-7-ITAL_INTERFACE_EVENT Received a [chars] event for unknown interface [chars]
Explanation The static routing process received a change notification event from ITAL for an interface which it was not tracking.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPMC_GTRIE_DEBUG Messages
Error Message%ROUTING-IPMC_GTRIE_DEBUG-3-ERR [chars]
Explanation This is a catch all error message. It usually means an uncorrectible problem
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPMC_GTRIE_DEBUG-3-INIT_ERR [chars] [dec] [chars] [dec] [chars]
Explanation Internal error. GTRIE debug library initilization failed
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPMC_GTRIE_DEBUG-6-TERM_ERR [chars] [dec] [chars] [dec] [chars]
Explanation Internal non-serious error. GTRIE debug library termination failed
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPMC_GTRIE_DEFAULT Messages
Error Message%ROUTING-IPMC_GTRIE_DEFAULT-2-FATAL [chars]
Explanation Internal error. Usually sever problems such as failing to free memory
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPMC_GTRIE_DEFAULT-3-INIT_ERR [chars]
Explanation Error while initializing Gtrie. Initialization failed and aborted
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPMC_GTRIE_DEFAULT-4-INIT_WARN [chars]
Explanation Error while initializing Gtrie. Initialization will continue
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPMC_GTRIE_DEFAULT-4-WARN [chars]
Explanation Internal error. A significant event but we can still continue
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV4_IGMP Messages
Error Message%ROUTING-IPV4_IGMP-3-ARM_UPDATE_ERR Interface [chars][[hex]] has vrf [chars] vrf_id [hex] set, New vrf [chars] vrf_id [hex]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-CHUNK_ERR Failed to create chunk for [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-CONTEXT_REG_ERR [chars] [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-EDM_INIT ERROR : [chars] - [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-GROUP_ADD_ERR [chars]Fail to add [chars] into group database
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-GROUP_ERR [chars]Group [chars] failed: [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-GROUP_FIND_ERR Fail to find [chars] in group database
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IDB_ADD_ERR [chars]Fail to add [chars] into database
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IDB_FREE_ERR [chars]Fail to free [chars] from database: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IDB_HANDLE_MISMATCH_ERR [chars]Interface [chars][[hex]][stale [chars]] handle mishmatch, handle in IM update [hex]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IDB_INIT_ERR [chars] - [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IDB_LOST_GROUPS_ERR [chars]Local joined groups on [chars] will be lost
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IDB_PRESENT_ERR [chars]Interface [chars][[hex]] is still present in vrf [chars]. check_idb [chars][[hex]] loc [dec]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IDB_STATE_MONITOR_ERR [chars]Fail to monitor interface state of [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IDB_VERIFY_ERR [chars]Interface [chars](context [chars]) doesn't belong to context [chars], please clear config error
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IDB_VERIFY1_ERR [chars]Interface [chars] has configured under context [chars] already
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IM_BATCH_STATE_ERR [chars]Invalid state for IM state registration batch on [chars] ([chars])
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IM_BULK_ERR Failed to [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-INIT_ERR [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-JOIN_IN_SSM_RANGE [chars]%s [chars] in SSM range. Join operation postponed
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-LTRACE_ERR Failed to [chars]: [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-MRIB_CONN_ERR MRIB connection error - [chars] in [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-NET_ERR [chars]%s : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-SOCK_ERR [chars]%s : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-SYSDB_BIND_ERR Sysdb Bind error for [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-SYSDB_BSCAN_ERR [chars]Sysdb backend scan failed for [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-SYSDB_INIT ERROR : [chars] - [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-SYSDB_REG_ERR Sysdb Registration error : [chars] for [chars] [[chars]]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-WDSYSMON_EVENT_ERROR Received an invalid event from WDSysmon
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-WDSYSMON_REGISTER_ERROR [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-4-OOM_STATE_THROTTLE Received [chars] memory depletion warning, stop creating new igmp state
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-4-OOM_STATE_UNTHROTTLE Node memory back to normal, new igmp states will be created
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-4-OOR_WARN [chars]%s: [dec]
Explanation Maximum number of group accepted, either per interface or globally.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-6-ACCESS_GROUP_INFO [chars]ACL applied, removed [chars] from [chars]
Explanation ACL applied to interface on which denied groups join previosly.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-6-IPARMS_UPDATE_ERR Dropping iparms update: type [chars] for [chars] [[hex]]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV4_MCAST_CHKPT Messages
Error Message%ROUTING-IPV4_MCAST_CHKPT-3-ERR Failed to [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV4_MCAST_NETIO_DEBUG Messages
Error Message%ROUTING-IPV4_MCAST_NETIO_DEBUG-3-INIT_ERR [chars] [dec] [chars] [dec] [chars]
Explanation Internal error. Multicast NetIO debug library initilization failed
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MCAST_NETIO_DEBUG-6-TERM_ERR [chars] [dec] [chars] [dec] [chars]
Explanation Internal non-serious error. Mcast netio debug library termination failed
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV4_MFWD_HFR Messages
Error Message%ROUTING-IPV4_MFWD_HFR-5-ERR_SYSDB_INIT [chars] : [chars]
Explanation The MFWD-HFR library encountered internal error during Sysdb init setup. The init setup will be retried for finite number of retries.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD_HFR-5-ERR_SYSDB_INIT [chars] : [chars]
Explanation The MFWD-HFR library encountered internal error during Sysdb init setup. The init setup will be retried for finite number of retries.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD_HFR-7-ERR_BAG_REGISTRY Couldn't register bags : [chars]
Explanation The MFWD-HFR library encountered internal error during sysdb/edm init setup. The init setup will be retried for finite number of retries.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD_HFR-7-ERR_BAG_REGISTRY Couldn't register bags : [chars]
Explanation The MFWD-HFR library encountered internal error during sysdb/edm init setup. The init setup will be retried for finite number of retries.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD_HFR-7-ERR_EDM_REGISTER Couldn't register edm : [chars]
Explanation The MFWD-HFR library encountered internal error during EDM init setup. The init setup will be retried for finite number of retries.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD_HFR-7-ERR_EDM_REGISTER Couldn't register edm : [chars]
Explanation The MFWD-HFR library encountered internal error during EDM init setup. The init setup will be retried for finite number of retries.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD_HFR-7-ERR_GEN [chars] failed : [chars]
Explanation MFWD-HFR library encountered error during setup. The init setup will be retried for finite number of retries.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD_HFR-7-ERR_GEN [chars] failed : [chars]
Explanation MFWD-HFR library encountered error during setup. The init setup will be retried for finite number of retries.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV4_MFWD Messages
Error Message%ROUTING-IPV4_MFWD-3-ADJ_CREATE [chars] [chars] : [chars]
Explanation Internal error: Cannot create the adjacency for a particular interface. Will retry for few times
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-BOUNDARY_FAIL [chars] [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR [chars]
Explanation These are unexpected errors
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_AIB_FINT [chars]: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_AIB_MAP Failed to map AIB table: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_AIB_ZERO_ALL [chars]: [chars]
Explanation We were not able to set all cached adjacencies to zero when we got ELIBBAD from AIB
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_DEBUG_INIT_EVENT Failed to initialize and chain together the debug event discriptors : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_DEBUG_REG Sysdb registration for debug config failed : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_EVM_ASYNC_ATTACH [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_EVM_CONN_CREATE Event connection create for [chars] failed: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_EVM_CONN_NOTIFY Event connection notify for [chars] failed: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_EVM_CONN_OPEN Event connection open for [chars] failed: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_EVM_CREATE Cannot create event manager : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_EVM_INIT_EVENT [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_EVM_TIMER_ATTACH [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_EVM_TIMER_LEAF_NEW [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_IDB_INIT Cannot intitialize IDB library : [chars]
Explanation Failed while initializing IDB library.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_IFH Failed to [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_IFH_BIND Failed to initialize pfi ifh connection: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_IFH_INIT Failed to initialize IFH server : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_IFH_UNBIND Failed to [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_IM_CNTL_SVR_BIND Failed to initialize im control server connection: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_IMC_CAPS_DATAPATH_CONTROL im_caps_datapath_control error for [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_MEM_ALLOC [chars]
Explanation These are unexpected errors
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_MLIB_INIT [chars] [chars]
Explanation Failed while initializing multicast library.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_MRIB_INIT Failed to initialize MRIB connection : [chars] failed : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_NSF_INIT Failed to initialize Multicast NSF : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_PAK_CLIENT_CONN Failed to initialize packet connection: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_SHMWIN [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_SYSDB_BAG_DECODE Error in bag decoding : [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_SYSDB_BAG_FREE_INDIRECTIONS Error in bag free : [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_SYSDB_BAG_REG Couldn't register bags : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_SYSDB_BSCAN SysDB operation [chars] failed: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_SYSDB_DATALIST_FREE Error in datalist free : [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_SYSDB_DATALIST_NEXT Error in datalist next : [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_SYSDB_EDM_FNS_INIT SysDB operation [chars] failed: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_SYSDB_EDM_REG SysDB operation [chars] failed: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_SYSDB_REG_NOTIFY SysDB operation [chars] failed: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_SYSDB_REG_VERIFY SysDB operation [chars] failed: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-EXIT Unexpected exit
Explanation Internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-GEN_ERR [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-GROUP_ERR [chars] [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-HA [chars]: [chars]
Explanation error while doing an HA operation (e.g. starting frequent restart monitor)
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-IARM_ERR [chars] [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-IDB_FAIL [chars] operation failed on [chars] [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-IM_LOOKUP_FAILED IM lookup failed for [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-INSTALL [chars] : [chars]
Explanation Error while performing upgrade/downgrade/install operation
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-LRD_ERR [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-MAX_CONN_RETRY Cannot connect to [chars] using event conn Mgr after [dec] retries: [chars]
Explanation Reached the maximum number of retries to connect to server using event conn
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-MAX_DISABLE_RETRY Failed to disable multicast after [dec] retries: [chars]
Explanation Reached the maximum number of retries to disable multicast
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-MAX_ENABLE_RETRY Failed to enable multicast [dec] retries: [chars]
Explanation Reached the maximum number of retries to enable multicast and
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-TABLE_OPERATION_FAIL [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-TABLE_OPERATION_FAIL_GLACIAL [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-TRANSACTION_PENDING_FLAG [chars] : [chars]
Explanation Failed to clear, set, or get transaction pending flag. That can only happen if the APIs to do that are called before shared mem window is opened, or if thereis a bug
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-TTL_CFG_FAIL [chars] [chars]: [chars]
Explanation Failed to apply a TTL threshold config. The operation will be retried.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-ADJ_CREATE_RETRY [chars] [chars] : [chars]. Retrying
Explanation Internal error: Cannot create the adjacency for a particular interface. Will retry for few times
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-CLEAN_ALL_FAIL [chars] [chars]
Explanation Failure while doing all reource cleanup
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-ERR_AIB_UPDATE Failed to [chars] AIB for interface [chars] : [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-ERR_LTRACE_INIT [chars] [chars]
Explanation Error ocured while enabling mcast
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-ERR_MRIB_INIT_RETRY Failed to initialize MRIB connection in [chars]. Retrying later: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-ERR_MRIB_SEND_RESPONSE_RETRY Failed to post signal to MRIB in [dec] retries. Reseting connection: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-ERR_RETRY_INIT [chars]: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-ERR_RETRY_TRANS_INIT [chars]: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-ERR_RETRY_TRANS_REG [chars]: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-ERR_RETRY_TRANS_SPEC_INIT [chars]: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-FROM_MRIB_UPDATE MFIB couldn't process update from MRIB : [chars] - [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-FROM_MRIB_UPDATE_GLACIAL MFIB couldn't process update from MRIB : [chars] - [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-SVD_ERR [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-TERMINATE [chars] [chars]
Explanation Error ocured while disabling mcast
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-TO_MRIB_MDT_UPDATE MFIB couldn't post MDT upd to MRIB: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-TO_MRIB_UPDATE MFIB couldn't post update to MRIB: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-CLEAN_ALL [chars] [chars]
Explanation Information regarding all resource cleanup
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-ERR_SHMWIN_MUTEX [chars] : [chars]
Explanation NetIO or Mfwd terminated while holding shared mem mutex. Recovery action will be taken
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-IP_ADDR_RETRY [chars] [chars]
Explanation APplying one or more IP address configs may have failed. We will retry them. This is a not a problem unless it keeps showing up continuously.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-MCAST_DISABLED [chars] [chars]
Explanation Most likely mfwd restarted and while it was down mcast was disabled. The other possibility is that mfwd retsarted while disabling mcast. In either case, when mfwd comes up, it will find that mcast is already disabled. Hence it will log this message and exit normally
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-MFIB_RESET [chars] : [chars]
Explanation Got notification that the the MFIB has been reset. Will clear MFIB and restart
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-MRIB_UPDATE_RETRY [chars] [chars]
Explanation Processing one or more updates may have failed. We will retry them. This is a not a problem.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-PER_PREFIX [chars] [chars]
Explanation Error while enabling/disabling per route accounting for a route
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-PER_PREFIX_GLACIAL [chars] [chars]
Explanation Error while enabling/disabling per route accounting for a route
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-ROUTE_UPDATE_FAIL [chars] Restarting to recover.
Explanation Was not able to commit at least one route after retrying for the maximum number of times. In this case, mfwd will restart in an attempt to recover. This is not an error. It just indicates that mfwd is restarting to recover from possible stale route problem.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-TABLE_PER_PREFIX Cannot [chars] per prefix accounting for table [chars]. [chars] [chars]
Explanation Error while enabling/disabling per route accounting in a table
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-TABLE_PER_PREFIX_GLACIAL Cannot [chars] per prefix accounting for table [chars]. [chars] [chars]
Explanation Error while enabling/disabling per route accounting in a table
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-TABLE_ROUTE_RATE Cannot [chars] rate for routes for table [chars]. [chars] [chars]
Explanation Error while enabling/disabling per route rate in a table
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-TABLE_ROUTE_RATE_GLACIAL Cannot [chars] rate for routes for table [chars]. [chars] [chars]
Explanation Error while enabling/disabling per route rate in a table
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-UPGRADE_AFFECT_TRAFFIC [chars] [chars]
Explanation Most likely some one tried to upgrade/downgrade mfwd while we're not connected to NetIO. In this case, teh upgrade will wipe out all MFIB and traffic will be disrupted
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV4_MLIB_DEBUG Messages
Error Message%ROUTING-IPV4_MLIB_DEBUG-3-ERR [chars]
Explanation This is a catch all error message. It usually means an uncorrectible problem
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB_DEBUG-3-INIT_ERR [chars] [dec] [chars] [dec] [chars]
Explanation Internal error. MLIB debug library initilization failed
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB_DEBUG-6-TERM_ERR [chars] [dec] [chars] [dec] [chars]
Explanation Internal non-serious error. MLIB debug library termination failed
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV4_MLIB Messages
Error Message%ROUTING-IPV4_MLIB-3-DATAPATH_CONTROL im_caps_datapath_control error in function [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-DELETE_FAIL Delete Failed for ([chars] [chars]/[dec]) from [chars] table [chars]
Explanation Internal error. Deleting an entry from ingress or egress failed
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-EVENT_CONN_MGR Cannot open event connection manager: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-EVENT_MGR Cannot create event manager: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-SHMWIN_ERR [chars] [chars]: [chars]
Explanation Error while doing shmwin operation
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-STATE_ERR [chars] [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-5-PER_PREFIX [chars] [chars]
Explanation Error while enabling/disabling per route accounting for a route
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-5-PER_PREFIX_GLACIAL [chars] [chars]
Explanation Error while enabling/disabling per route accounting for a route
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-5-SVD [chars]
Explanation Error while enabling/disabling per route accounting in a table
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-5-TABLE_PER_PREFIX Cannot [chars] per prefix accounting for table [chars]. [chars] [chars]
Explanation Error while enabling/disabling per route accounting in a table
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV4_PIM Messages
Error Message%ROUTING-IPV4_PIM-3-ACL_APPLY_ERR Failed to apply ACL for [chars] - [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ACL_GETLIST_ERR Cant get ACL for RP config [chars]: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ACTIVE_GRANGE_ERR [chars]Invalid state - active grange in mrib [chars]/[dec] RP - [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-BGP_ENS_ERROR PIM BGP communication [chars], [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-CONTEXT_CREATE Failed to create PIM context for vrf [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-CONTEXT_INIT [chars] [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-CONTEXT_REGISTRATION Ital init failed [dec]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_CHKPT_REGISTER [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_CHUNK_CREATE [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_DEBUG_REGISTER [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_EVM_ASYNC_ATTACH [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_EVM_ASYNC_SEND Error sending async message to [chars] thread during [chars] with pulse code [dec]: error equals [dec]([chars])
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_EVM_CONN_CREATE [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_EVM_CONN_EVM_HANDLER [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_EVM_CONN_NOTIFY [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_EVM_CONN_OPEN [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_EVM_CONN_SETRETRY [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_EVM_EVENT_INIT [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_EVM_MESSAGE_ATTACH [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_IM_BATCH_STATE [chars]Invalid state for IM state registration batch on [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_IM_BULK Failed to [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_IM_CAPS_ADD Interface Manager error - [chars] [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_IM_CAPS_DATAPATH_CONTROL Interface Manager error - [chars] [chars] : [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_IM_INTERFACE_CREATE [chars]Interface Manager error - [chars] [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_IM_INTERFACE_DELETE [chars]Interface Manager error - [chars] [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_INIT [chars]%s : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_LIST [chars]List error : [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_LTRACE_INIT ltrace_init failed for '[chars]': [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_MAX_PATH [chars]RIB max path exceeded for [chars], total paths: [dec], reset to maximum
Explanation A software error has occurred while trying to read out the checkpointed rpf data. PIM rpf info may be incorrect
Recommended Action Check show pim rpf output for correctness Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_MEM_ALLOC [chars]for [chars] [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_MGD_TIMER_GET_ROOT [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_MGD_TIMER_NEW [chars]%s : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_MRIB_BIND [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_MRIB_CONN MRIB connection error - [chars] : [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_MRIB_UNBIND [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_NSF_INIT [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_PAK_CLIENT_CONN [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_SYSDB_BAG_DECODE Error in bag decoding : [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_SYSDB_BAG_FREE_INDIRECTIONS Error in bag free : [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_SYSDB_DATALIST_FREE Error in datalist free : [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_SYSDB_DATALIST_NEXT Error in datalist next : [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_SYSMGR_READY [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_SYSMGR_REGISTER [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_WDSYSMON_EVENT Received an invalid event from WDSysmon
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_WDSYSMON_REGISTER [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-GEN_ERR [chars]Error - [chars] [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-IDB_HANDLE_MISMATCH_ERR Interface handle mismatch, handle in IM update [chars]:[hex], handle in PIM [chars]:[hex]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-IDB_INIT [chars]%s : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-IDB_VRF_BIND [chars]Interface [chars] belongs to context [chars]. Please clear the config error
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-INTF_FWD_REF_ERR [chars]Interface Forward Reference Store error - [chars]: [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-INVALID_MHOST_DEFAULT [chars]Interface [chars] should not be configured as mhost default
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-MDR_INIT [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-MULTICAST_IGP_MTR [chars] [chars] multicast topology incorrect sysdb deletes received, refcount [dec]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-MULTICAST_INTACT [chars]%s multicast intact incorrect sysdb deletes received, refcount [dec]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-NET_ERR [chars]%s : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-OOR_COUNTER_ERR [chars]OOR [chars] counter has turned negative: [dec]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-PROTOCOL_ERR [chars]%s - [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-RP_INIT [chars]%s : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-SRC_UPDATE_ERR Error in [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-CFG_WARNING [chars]%s
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-ITAL_CREATE_WARN ITAL create notification for table with pending cleanup old vrf_id [hex], table_id [hex] : route count [dec] : new vrf_id [hex] table_id [hex]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-MIB_GROUP_TREE_ERR [chars]Failed to [chars] [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-MYADDR_DB_ERR [chars]Failed operation: [chars] for [chars] - [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-OOM_STATE_THROTTLE Received [chars] memory depletion warning, stop creating new pim state
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-OOM_STATE_UNTHROTTLE Node memory back to normal, new pim states will be created
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-OOR_REGISTER_OK [chars]The number of PIM Register states ([unsigned int]) is now below the maximum. Normal PIM Register handling will resume.
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-OOR_REGISTER_WARN [chars]The maximum number of PIM Register states ([unsigned int]) has been reached. Register state creation will be throttled. Configure a higher maximum or take steps to reduce Register state.
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-OOR_ROUTES_OK [chars]The number of PIM routes ([unsigned int]) and route-interfaces ([unsigned int]) are now below the maximum. Normal PIM route handling will resume.
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-OOR_ROUTES_WARN [chars]The maximum number of PIM routes ([unsigned int]) or route-interfaces ([unsigned int]) has been reached. Route creation will be throttled. Configure a higher maximum or take steps to reduce multicast state.
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-RANGE_INIT [chars]%s in [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-5-INTCHG [chars]PIM interface [chars] [chars]
Explanation PIM interface state change message.
Recommended Action No action is required.
Error Message%ROUTING-IPV4_PIM-5-INVALID_JP [chars]PIM invalid (*, [chars]) J/P message from [chars] with RP address [chars]
Explanation PIM invalid J/P notification.
Recommended Action No action is required.
Error Message%ROUTING-IPV4_PIM-5-INVALID_REGISTER [chars]PIM invalid register message from [chars] for group [chars] RP address [chars], [chars]
Explanation PIM invalid register message notification.
Recommended Action No action is required.
Error Message%ROUTING-IPV4_PIM-5-NBRCHG [chars]PIM neighbor [chars] [chars] on [chars] [chars]
Explanation PIM neighbor state change message.
Recommended Action No action is required.
Error Message%ROUTING-IPV4_PIM-5-RP_MAPPING_CHG [chars]PIM [chars] for [chars]/[dec] RP [chars] proto [chars]
Explanation PIM RP mapping change notificaiton.
Recommended Action No action is required.
IPV6_FIB Messages
Error Message%ROUTING-IPV6_FIB-2-RIBREJECT Rejecting RIB Update for [chars]/[dec] status [dec]
Explanation Rejected a route update from the RIB.
Recommended Action Try repopulating the missing route. If not recovered, it will lead to forwarding inconsistencies. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. *SUPPORT*
Error Message%ROUTING-IPV6_FIB-7-PFIFAIL PFI-IFH Server Error for [hex] status equals ([dec])
Explanation Cannot talk to the PFI-IFH process
Recommended Action Informational message. PFI-IFH process does not have the information about the interface-handle at this very moment Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
ISIS_IP_ORA Messages
Error Message%ROUTING-ISIS_IP_ORA-3-INSTBUILD Failed to build policy operation '[chars]' for attribute '[chars]'.[chars]%s ([hex])
Explanation There was an internal error in the routing policy library and as a result routing policy may not be applied correctly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
ISIS Messages
Error Message%ROUTING-ISIS-3-INTF_SET_ADD_FAIL Failed to add [chars] to the set of [chars]: [hex], '[chars]'
Explanation An unexpected error occurred whilst trying to add an interface to the specified collection of interfaces. This is most likely to be due to a low memory condition, but may be an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Consider restarting the IS-IS process. *RECUR*
Error Message%ROUTING-ISIS-4-INTF_ADDR_CHG_REG Error during registration for interface IP address changes: [chars]
Explanation IS-IS failed to register for notification of interface IP address changes. This is may be due to lack of resources or an internal error (the error message will indicate which). It requires a restart of the process for recovery.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-INTF_ATTR_FAIL Failure while [chars] on [chars]: [hex] '[chars]''
Explanation A call to the IM attribute library failed. This can be caused by faulty hardware, or it may indicate an interface resource is currently unavailable. Recovery may require a restart of the IS-IS process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_CKTNUM_ALLOC_FAIL Failed to allocate circuit ID to interface [chars]: all [dec] IDs already in use
Explanation IS-IS failed to allocate a circuit ID to the specified LAN interface.
Recommended Action Reduce the number of LAN interfaces over which IS-IS is running.
Error Message%ROUTING-ISIS-4-INTF_CLNS_CLIENT_INIT Failed to initialize CLNS interface registery: [chars]
Explanation IS-IS failed to initialize its interface registration process wth CLNS It requires a restart of process for recovery.
Recommended Action Restart the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_CLNS_MAC_ADDR_NOTIFY Failed to notify CLNS of a MAC address change on interface [chars]: [chars]
Explanation IS-IS failed to notify the CLNS protocol stack of MAC address changes to the specified interface. It requires a restart of process for recovery.
Recommended Action Restart the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_CLNS_NOTIFY Failed to add the CLNS stack on interface [chars]: [chars]
Explanation IS-IS failed to add the CLNS protocol stack on the specified interface. It requires a restart of process for recovery.
Recommended Action Restart the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_CLNS_REMOVE_CAP Failed to remove the CLNS stack on interface [chars]: [chars]
Explanation IS-IS failed to remove the CLNS protocol stack on the specified interface.
Recommended Action None.
Error Message%ROUTING-ISIS-4-INTF_FIND_FAIL Failed to lookup Interface Handle for interface [chars]: [hex] '[chars]'
Explanation An unexpected error occurred looking up an interface handle from an interface name. This may be due to a low memory condition but is most likely to be an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. *RECUR*
Error Message%ROUTING-ISIS-4-INTF_FWS_INIT Error during initialization of forward-referenced interface store: [chars]
Explanation IS-IS failed to initialize its storage for forward-referenced interfaces. This is may be due to lack of resources or an internal error (the error message will indicate which). It requires a restart of the process for recovery.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-INTF_IM_REG_FAIL Error registering for [chars] [chars] changes on interface [chars]: [hex], '[chars]'
Explanation IS-IS failed to register for notification of the specified changes on the specified interface and protocol. This may be an internal programming error, but is most likely to be a resource starvation problem.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Consider disabling and reenabling the interface within IS-IS configuration, or restarting the IS-IS process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..
Error Message%ROUTING-ISIS-4-INTF_INACTIVE_AF Unexpected [chars] [chars] notification on [chars]
Explanation The specified event was unexpected because the address family is not active on that interface. The operation of IS-IS is not affected by this message and it may safely be ignored. The message is due to an internal programming error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..
Error Message%ROUTING-ISIS-4-INTF_IP_ARM_BATCH_UPDATE_FAIL Error [chars] for [chars] address changes on interface [chars]: [hex], '[chars]'
Explanation IS-IS failed to register with IP-ARM for notification of the address changes on the specified interface and address family. This may be an internal commuincation error, but is most likely to be a resource starvation problem.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Consider disabling and reenabling the interface within IS-IS configuration, or restarting the IS-IS process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..
Error Message%ROUTING-ISIS-4-INTF_LAS_FAIL Failed [chars] [chars] link local addresses on [chars]: [hex], '[chars]'
Explanation An unexpected error occurred whilst accessing the link-local address details for the specified interface. As a result IS-IS will not be able to use the specified address-family on the specified interface. This could be due to a low memory condition or an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Consider restarting the IS-IS process. *RECUR*
Error Message%ROUTING-ISIS-4-INTF_MAC_SIZE_ERR Incorrect MAC address size for [chars] (returned: [dec], expected: [dec])
Explanation The MAC address size returned for the specified interface does not match the expected size (6 bytes). This can be caused by a faulty hardware.
Recommended Action Restart the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_MCAST_JOIN_FAIL Error joining [chars] multicast group on [chars]: [chars]
Explanation IS-IS was unable to join the specified multicast group on the specified interface.
Recommended Action Restart the affected interface and, if the problem recurs, the IS-IS process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_MCAST_SIZE_ERR The multicast address is too large for [chars] (supplied: [dec], maximum: [dec])
Explanation The multicast address requested for the specified interface is larger than the maximum permissible size. This requires restarting the IS-IS process.
Recommended Action Restart the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_MTU_REDUCED IS-IS MTU value of [unsigned int] on [chars] adjusted to [unsigned int] to accommodate fabric MTU
Explanation The IS-IS MTU was adjusted to accommodate the fabric MTU of the system. This new MTU may be smaller than the actual MTU allowable by the physical interface.
Recommended Action Check any MTU configuration for the interface to ensure that this is not a configuration error. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_MTU_TOO_SMALL CLNS MTU value of [unsigned int] on [chars] is too small. Minimum acceptable value is [unsigned int]
Explanation The MTU for CLNS on the specified interface is too small to allow IS-IS to send packets over that interface. This may be due to a configuration error or an internal error.
Recommended Action Check any MTU configuration for the interface to ensure that this is not a configuration error. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_NAME_FAIL Failed to lookup an interface name from its handle ([hex]): [hex], '[chars]'
Explanation An unexpected error occurred looking up an interface's name from it's handle. The error code should provide an indication of what the problem is. The most likely explanation is that the interface with the specified handle no longer exists although the message may be caused by low memory conditions or an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. *RECUR*
Error Message%ROUTING-ISIS-4-INTF_NSF_MEDIA_MISMATCH Media class mismatch between checkpoint table ([chars]) and reality ([chars]) on interface [chars]
Explanation IS-IS has detected a mismatch between the media class (i.e. Point to Point vs. LAN) of an interface as determined by IS-IS's checkpoint state and IM. As a result the interface will not participate in the NSF restart. This is an internal programming error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_STORE_FAIL Error [chars] [chars] [chars] internal [chars] store: [hex], [chars]
Explanation IS-IS was unable to perform the specified operation on the specified interface. This is most likely to be a resource starvation problem, but may be an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Consider restarting the IS-IS process. *RECUR*
Error Message%ROUTING-ISIS-4-INTF_UNKNOWN_MEDIA Unknown or unsupported interface media type ([chars]) on [chars]
Explanation This interface media is not supported by IS-IS. An IS-IS process restart is required for recovery.
Recommended Action Check the interface media name in the configuration and restart the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
LDP Messages
Error Message%ROUTING-LDP-3-ERR_BACKEND Backend scan failed for '[chars]': [chars]
Explanation LDP failed backend scan for some tuple path.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-3-ERR_GENERAL [chars]
Explanation A general error occurred within LDP. The details appear in the output.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-3-ERR_INIT_SYNC_MISSING_SOCK Init Sync Done: Missing Pending Socket([chars])
Explanation Received Init Sync Done notification but socket wasn't in pending database.
Recommended Action No action is required.
Error Message%ROUTING-LDP-3-ERR_LSD_INTF LSD Intf-[chars] failed for [chars] (ifh [hex]): [chars]
Explanation LDP encountered some problem while trying to enable/disable MPLS on an interface via LSD server.
Recommended Action Make sure that LSD is running and LDP is connected/registered with it.
Error Message%ROUTING-LDP-3-ERR_LSD_REG LSD application registration failed: [chars]
Explanation LDP encountered a problem while trying to register with LSD server.
Recommended Action Make sure that LSD is running and LDP is connected to it.
Error Message%ROUTING-LDP-3-ERR_TCP_ENQUEUE_MSG_INVALID_TX_CTX TCP: Msg Enqueue Failed: Invalid Tx Ctx.
Explanation Msg was enqueued with non-NULL tx ctx when NSR is disabled.
Recommended Action Remove source of transmit.
Error Message%ROUTING-LDP-3-ERR_TCP_ENQUEUE_MSG_NOT_ACTIVE TCP: Msg Enqueue Failed: Node isn't active.
Explanation Standby Node tried to transmit LDP message.
Recommended Action Remove source of transmit.
Error Message%ROUTING-LDP-3-INCONSISTENCY An internal inconsistency was detected:[chars]
Explanation LDP has detected an internal inconsistency. Please capture a core file for analysis.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-3-LOST_NSR_IPC_MSG An inter-card NSR msg was lost
Explanation A received sequence number did not match the expected one.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-3-NSR_ACK_CHK_FAILED NSR ACK CHK failed: [chars]; count [dec]
Explanation NSR ACK CHK failed. Please perform show mem heap for analysis.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-3-NSR_PEER_SYNC_RX_ERR Peer [chars]; op equals '[chars]'; [chars]
Explanation Standby LDP instance encountered an error during processing of NSR synchronization data sent by Active LDP instance.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-4-BAD_PDU_LENGTH A message with botched PDU length is received from peer [chars]
Explanation A message with botched PDU length is received from the network.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-4-BAD_TLV TLV Check failed for a message (type [hex]) received from peer [chars]
Explanation A message with a bad TLV is received from the network.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-4-DEPRECATED_RTRID 'router-id interface command is deprecated. Delete 'router-id [chars]' and reconfigure 'router-id ip_addr'.
Explanation MPLS LDP 'router-id interface' command is deprecated.
Recommended Action Use 'router-id ip_addr'.
Error Message%ROUTING-LDP-4-DISCOVERY_SLIP CPU load or blockage caused latent tx of UDP discovery to [chars]: interval equals [dec] sec, expected equals [dec] sec. Hold equals [dec] sec
Explanation Heavy CPU load or process blockage resulted in slip of discovery transmission. Possibly resulting in session/adjacency flap.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-4-DUP_ADDR_RCVD Duplicate Address [chars] advertised by peer [chars] is already bound to peer [chars]
Explanation LDP received an Address advertisement for an address from a peer, but the address is already bound to a different peer.
Recommended Action Fix the misconfiguration in the network and clear LDP sessions which have Address bindings which should not exist or are missing Address bindings which should exist.
Error Message%ROUTING-LDP-4-TX_KEEPALIVE_SLIP CPU load or blockage caused latent tx of LDP keepalive to [chars]: interval equals [dec] sec, expected equals [dec] sec. Hold equals [dec] sec
Explanation Heavy CPU load or process blockage resulted in slip of discovery transmission. Possibly resulting in session.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-5-GR GR session [chars] (instance [dec]) [chars]
Explanation An LDP GR session state change has occured - such as disconnected, reconnected, timed out, forced abort, and cleaned up. This message appears only if the log graceful-restart command is configured.
Recommended Action No action is required.
Error Message%ROUTING-LDP-5-GR_RESTART_COMPLETE GR forwarding state hold timer has expired
Explanation After LDP local restart, LDP GR forwarding state hold timer has expired, and MPLS forwarding is now being updated and reinstated by LDP application. This message appears only if the log graceful-restart command is configured.
Recommended Action No action is required.
Error Message%ROUTING-LDP-5-NBR_CHANGE Neighbor [chars], [chars] [chars]
Explanation A LDP neighbor has changed state (up/down). If neighbor has went down, then a reason for session going down is also displayed. This message appears only if the log neighbor command is configured for the LDP process.
Recommended Action No action is required.
Error Message%ROUTING-LDP-5-NSR_SYNC_DONE Initial synchronization successfully done for [dec] peers
Explanation LDP Non-stop routing initial-sync event has completed successfully for some or all peers. This message appears only if the mpls ldp log nsr command is configured.
Recommended Action If number of peers do not match the number of peer for SYNC_START, then Check LDP logs and traces to see why not all attempted peers were successfully synced.
Error Message%ROUTING-LDP-5-NSR_SYNC_LOST Global synchronization lost
Explanation LDP Non-stop routing synchronization lost with the standby node. This message appears only if the mpls ldp log nsr command is configured.
Recommended Action No action is required.
Error Message%ROUTING-LDP-5-NSR_SYNC_PEER_DONE Peer [chars] initial synchronization done
Explanation LDP Non-stop routing peer initial-sync event has completed successfully. This message appears only if the mpls ldp log nsr command is configured.
Recommended Action No action is required.
Error Message%ROUTING-LDP-5-NSR_SYNC_PEER_LOST Peer [chars] synchronization lost
Explanation LDP Non-stop routing synchronization lost for the peer. This message appears only if the mpls ldp log nsr command is configured.
Recommended Action No action is required.
Error Message%ROUTING-LDP-5-NSR_SYNC_START Initial synchronization started for [dec] peers
Explanation LDP Non-stop routing initial-sync event has been started for all eligible peers. This message appears only if the mpls ldp log nsr command is configured.
Recommended Action No action is required.
Error Message%ROUTING-LDP-5-SESSION_PROTECTION [chars] for peer [chars]
Explanation An informational LDP notice was generated for a Session Protection event.
Recommended Action No action is required.
Error Message%ROUTING-LDP-5-SHUTDOWN LDP process is shutting down due to '[chars]' memory state.
Explanation LDP process exiting due to unknown/critical node memory state.
Recommended Action Start 'mpls_ldp' process after memory state goes normal.
Error Message%ROUTING-LDP-6-ISYNC_CHKPT_LIMIT Limit reached for maximum ([dec]) number of neighbors per interface
Explanation LDP checkpointing has limit for maximum number of neighbors per interface due to LDP IGP Sync feature requirements. It is not recommended to cross the limit provided by Engineering. If crossed, undesired affects can be seen and LDP IGP Sync feature may not work.
Recommended Action Limit number of neighbors to the value as provided in Engineering guidelines
Error Message%ROUTING-LDP-7-ERR_INIT '[chars]' ([chars])
Explanation An internal system error occurred during initialization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-7-ERR_INIT_FATAL Failed to initialize '[chars]': [chars]: Process now terminating
Explanation A fatal error occurred during initialization of an LDP subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
LMRIB_API Messages
Error Message%ROUTING-LMRIB_API-3-ASYNC_ERR Asynchronous error: [chars]
Explanation 'An unhandled asynchromous error occurred in the LMRIB API'
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LMRIB_API-3-CORRPT Corrupted update: [chars]. (expected [dec] bytes, got [dec] bytes)
Explanation 'A corrupted update was received from the LMRIB by the LMRIB API'
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LMRIB_API-3-GEN_ERR [chars]
Explanation Error occurred in lmrib client lib.
Recommended Action No action is required.
Error Message%ROUTING-LMRIB_API-3-GENINITFAIL Initialization failed: [chars] [chars]
Explanation Error occurred at client initialization.
Recommended Action No action is required.
Error Message%ROUTING-LMRIB_API-3-RPC_FAIL RPC failure: [chars]
Explanation 'An RPC-related error occurred in an RPC call from the LMRIB API'
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LMRIB_API-7-ASYNC_WAR Warning: [chars]
Explanation 'A recoverable error condition occurred in the LMRIB API'
Recommended Action No action is required.
LSPV Messages
Error Message%ROUTING-LSPV-3-BAG_REG_ERR bag(s) registration failed: [chars]
Explanation Some error occured while trying to register edm bags. The text of the message displays the failed operation with error code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LSPV-3-SYSDB_BIND_ERR sysdb_bind failed for '[chars]': [chars]
Explanation Some error occured in sysdb bind operation bind. The text of the message displays the failed operation for the bindpoint with error code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LSPV-3-SYSDB_ERR [chars] failed: [chars]
Explanation Some error occured in sysdb operation. The text of the message displays the failed operation with error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LSPV-4-show_timeout [chars]
Explanation It was not possible to obtain the lock required to access the databases. This may be due to the main thread being very busy processing events.
Recommended Action Wait a few minutes, and re-attempt to issue the show command.
Error Message%ROUTING-LSPV-7-ERR_EVENT [chars] failed: error equals [hex] ([chars])
Explanation Some error occured in event/event manager/event connection operations. The text of the message displays the failed operation with error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LSPV-7-ERR_GENERAL [chars] failed: error equals [hex] ([chars])
Explanation Some requested operation failed. The text of the message displays the failed operation with error code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LSPV-7-ERR_INIT Failed to init '[chars]'. Process now terminating
Explanation Initialization of some subsystem failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LSPV-7-ERR_INIT_RC Failed to init '[chars]': error equals [hex] ([chars]). Process now terminating
Explanation Initialization of some subsystem failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LSPV-7-ERR_TIMER [chars] failed: error equals [hex] ([chars])
Explanation Some error occured in operations with mdg timers. The text of the message displays the failed operation with error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MFWD_MA Messages
Error Message%ROUTING-MFWD_MA-3-CFG_ERR [chars] cfg counter already 0. Can't decrement : Item is [chars].
Explanation A general error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_DEBUG_INIT_EVENT Failed to initialize and chain together the debug event discriptors : [chars]
Explanation An error related to the debugging subsystem occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_DEBUG_REG Sysdb registration for debug config failed : [chars]
Explanation An error related to the debugging subsystem occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_EVM_ASYNC_ATTACH [chars] : [chars]
Explanation A general error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_EVM_CONN_CREATE Event connection create for [chars] failed : [chars].
Explanation A general error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_EVM_CONN_NOTIFY Event connection notify for [chars] failed : [chars].
Explanation A general error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_EVM_CONN_OPEN Event connection open for [chars] failed : [chars].
Explanation A general error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_EVM_CREATE Cannot create event manager : [chars]
Explanation An unrecoverable error occurred at system initialization time.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_IMC_CONTROL_SERVER_BIND Error in imc control server bind : [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_LTRACE_INIT [chars] : [chars]
Explanation An unrecoverable error occurred at system initialization time.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_MEM_ALLOC [chars]
Explanation A general error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_MEM_FAIL [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_MEM_FAIL_1 [chars] : [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_SYSDB_BAG_DECODE Error in bag decoding : [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_SYSDB_BAG_FREE_INDIRECTIONS Error in bag free : [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_SYSDB_BAG_REG Cannot register bags : [chars].
Explanation A general error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_SYSDB_BIND Error in sysdb bind : [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_SYSDB_DATALIST_FREE Error in datalist free : [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_SYSDB_DATALIST_NEXT Error in datalist next : [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_SYSDB_EDM_FNS_INIT SysDB Oper - [chars] failed : [chars].
Explanation A general error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_SYSDB_EDM_REG SysDB Oper - [chars] failed : [chars].
Explanation A general error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_SYSDB_REG_VERIFY SysDB operation [chars] failed: [chars]
Explanation A general error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_SYSDB_VRFN_FNS_INIT SysDB operation [chars] failed: [chars]
Explanation A general error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-GEN_ERR [chars] failed : [chars].
Explanation A general error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-GENINITFAIL Initialization failed: [chars] [chars]
Explanation An unrecoverable error occurred at system initialization time.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-IDB_ERR [chars] failed for [chars] [[hex]] : [chars]
Explanation A general error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-IM_UPDATE_IDB_HANDLE_MISMATCH idb [chars] has handle [[hex]], IM update has [[hex]]
Explanation A general error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MPLS_ALM Messages
Error Message%ROUTING-MPLS_ALM-7-ERR_GENERAL [chars] : [chars]
Explanation An internal system error occured.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MPLS_HW Messages
Error Message%ROUTING-MPLS_HW-2-ERROR [chars]. Error equals [chars] (errno equals [dec]).
Explanation There was a critical system call failure resulting in a failure to provide some system service as indicated in the message text.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%ROUTING-MPLS_HW-2-ERROR [chars]. Error equals [chars] (errno equals [dec]).
Explanation There was a critical system call failure resulting in a failure to provide some system service as indicated in the message text.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%ROUTING-MPLS_HW-2-ERROR_TLU_ALLOC [chars]. Error equals [chars] (errno equals [dec]).
Explanation Hardware memory allocation for table lookup unit (TLU) failed. This can be because the system has more forwarding entries than supported limits or there is a software defect.
Recommended Action Please collect output of show tlu server summary [egress/ingress] loc to see why the line card is running out of forwarding entries. Then try to reduce the entries if possible. Copy the error message and report to your technical support representative.
Error Message%ROUTING-MPLS_HW-2-ERROR_TLU_ALLOC [chars]. Error equals [chars] (errno equals [dec]).
Explanation Hardware memory allocation for table lookup unit (TLU) failed. This can be because the system has more forwarding entries than supported limits or there is a software defect.
Recommended Action Please collect output of show tlu server summary [egress/ingress] loc to see why the line card is running out of forwarding entries. Then try to reduce the entries if possible. Copy the error message and report to your technical support representative.
Error Message%ROUTING-MPLS_HW-2-ERROR_TLU_WRITE [chars]. Error equals [chars] (errno equals [dec]).
Explanation Hardware memory write for table lookup unit (TLU) failed. This can because 1) connection to mipc lost. 2) mipc/metro problem.
Recommended Action Please collect output of show pse ipc clinet-connection all loc and show asic-errors pse [0|1] all loc . Copy the error message and report to technical support representative.
Error Message%ROUTING-MPLS_HW-2-ERROR_TLU_WRITE [chars]. Error equals [chars] (errno equals [dec]).
Explanation Hardware memory write for table lookup unit (TLU) failed. This can because 1) connection to mipc lost. 2) mipc/metro problem.
Recommended Action Please collect output of show pse ipc clinet-connection all loc and show asic-errors pse [0|1] all loc . Copy the error message and report to technical support representative.
Error Message%ROUTING-MPLS_HW-2-ERROR_WITH_LABEL [chars]. Error equals [chars] (errno equals [dec]). Out label equals [dec].
Explanation There was a critical system call failure resulting in a failure to provide some system service as indicated in the message text.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%ROUTING-MPLS_HW-2-ERROR_WITH_LABEL [chars]. Error equals [chars] (errno equals [dec]). Out label equals [dec].
Explanation There was a critical system call failure resulting in a failure to provide some system service as indicated in the message text.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%ROUTING-MPLS_HW-6-INFO [chars]. Error equals [chars] (errno [dec]).
Explanation There was an internal failure that may impact non-essential system function.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%ROUTING-MPLS_HW-6-INFO [chars]. Error equals [chars] (errno [dec]).
Explanation There was an internal failure that may impact non-essential system function.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%ROUTING-MPLS_HW-6-INFO_WITH_LABEL [chars]. Error equals [chars] (errno [dec]). Out label equals [dec].
Explanation There was an internal failure that may impact non-essential system function.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%ROUTING-MPLS_HW-6-INFO_WITH_LABEL [chars]. Error equals [chars] (errno [dec]). Out label equals [dec].
Explanation There was an internal failure that may impact non-essential system function.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
MPLS_IO Messages
Error Message%ROUTING-MPLS_IO-3-ERR_MEM_ALLOC [chars] failed :[chars]
Explanation Some error occurred in Alloc/Chunk related memory operations. The text of the message displays the failed operation and the related memory construct. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_IO-6-ERR_GENERAL [chars]: [chars]
Explanation Some informational message with cerrno.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_IO-7-ERR_IM [chars] failed: [chars]
Explanation Some error occurred in operations with IM. The text of the message displays the failed operation and the related error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_IO-7-ERR_PAK [chars] failed: [chars]
Explanation Some error occurred in Packet (IP/MPLS/ICMP) related operations. The text of the message displays the failed operation and the related error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_IO-7-ERR_TIMER [chars] failed for '[chars]': [chars]
Explanation Some error occurred in Managed Timer related operations. The text of the message displays the failed operation and the related timer construct with error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_IO-7-ERR_WAVL [chars] failed (tree equals [chars]): [chars]
Explanation Some error occurred in WAVL operations The text of the message displays the failed operation and the related wavl tree. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MPLS_LCAC Messages
Error Message%ROUTING-MPLS_LCAC-4-SHOW_WARNING The show thread waited [unsigned int] seconds and could not acquire the mutex.
Aborting show request. Please try again. If this problem persists,
please contact your technical service representative.Explanation The show thread could not acquire the mutex to service the show request. The main thread in te_control may be busy/blocked/hogging while holding That mutex.
Recommended Action Try to run the show command again. If the error reoccurs, then check the state of the te_control process (show process te_control). If thread number 1 is blocked for an extended period of time, contact your technical service representative.
Error Message%ROUTING-MPLS_LCAC-7-ERR_INTERNAL [chars]
Explanation An internal system error occured.
Recommended Action Copy the message exactly as it appears and report it to your technical service representative.
MPLS_LSD Messages
Error Message%ROUTING-MPLS_LSD-2-ERR_MEM_ALLOC Insufficient memory for '[chars]', [unsigned int] bytes, terminating
Explanation MPLS LSD terminated due to lack of memory for a critical operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LSD-3-ERR_INVALID_THREAD Callback from ENS on incorrect thread, actual/expected equals [dec]/[dec] (CSCsd51829)
Explanation Detected single-threaded mpls-lsd code running on an unknown thread. This concurrency can result in corruption.
Recommended Action Collect LSD traces
Error Message%ROUTING-MPLS_LSD-3-MULTI_IP_FPI_RW [chars]
Explanation Rewrite creation or modification failed due to presence of multiple IP route elements.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LSD-7-ERR_CLIENT_FAULT [chars]
Explanation Client error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LSD-7-ERR_GENERAL [chars]
Explanation Miscellaneous MPLS LSD error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LSD-7-ERR_INIT Initialization of MPLS LSD failed, op equals '[chars]' ([chars])
Explanation MPLS LSD failed to initialize for the reason displayed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MPLS_NETIO Messages
Error Message%ROUTING-MPLS_NETIO-5-CLEAR_MAPPING_FAILED control clear mapping for [chars] mpls proto [dec] failed [chars]
Explanation MPLS could not clear control mapping for underlying protocol.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_NETIO-5-SET_MAPPING_FAILED control set mapping for [chars] to [hex]/[hex] mpls proto [dec] failed [chars]
Explanation MPLS could not set control mapping for underlying protocol.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_NETIO-7-BAD_ARP_DROP Pkt([pointer]) with no nexthop in HSSD, output interface - CH[hex]. MPLS label stack:[chars]. IP info:[chars]. HSSD info:[chars].
Explanation MPLS slowpath got a packet for which ARP needs to be done, but, it doesn't have the nexthop needed. The pkt is dropped.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_NETIO-7-ERR_GENERAL [chars] FAILED: [chars]
Explanation Some miscellaneous error occured. The text of the message explains the err/warning and traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MPLS_STATIC Messages
Error Message%ROUTING-MPLS_STATIC-4-ERR_MEM_ALLOC Memory allocation failed for [chars]
Explanation Allocation of memory failed.
Recommended Action Add more memory.
Error Message%ROUTING-MPLS_STATIC-6-ERR_CONN Connection to the [chars] failed ([chars])
Explanation MPLS static process could not connect with a manager.
Recommended Action No action is required.
Error Message%ROUTING-MPLS_STATIC-7-ERR_INIT Initialization of MPLS Static failed - [chars] ([chars])
Explanation Initialization of the MPLS Static process failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MPLS_TE Messages
Error Message%ROUTING-MPLS_TE-3-CALLBACK_WRONG_THREAD A callback ([chars]) has been received in the wrong thread ([unsigned int], should be in [unsigned int]). The callback has not been handled.
Explanation A callback from the IOX-XR infrastructure was not handled by the MPLS-TE process because it was received in the wrong thread. The TE process may now be in an inconsistent state with the rest of the system.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. The te_control process may be restarted in order to recover from this situation.
Error Message%ROUTING-MPLS_TE-3-ERR_INTERNAL_CHECK [chars](): line [unsigned int]: [chars]
Explanation An inconsistency in internal state was detected.
Recommended Action Copy the message exactly as it appears and report it to your technical service representative.
Error Message%ROUTING-MPLS_TE-3-ERR_INTERNAL_CHECK_RC [chars](): line [unsigned int]: [chars]: error [chars] ([hex])
Explanation An inconsistency in internal state was detected.
Recommended Action Copy the message exactly as it appears and report it to your technical service representative.
Error Message%ROUTING-MPLS_TE-3-ERR_MEM_ALLOC Memory allocation failed for [chars]
Explanation Allocation of memory failed.
Recommended Action This indicates a low memory condition. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-MPLS_TE-3-ERR_SYSDB_BAG_DECODE [chars]: [chars]: [chars]
Explanation A Bag related error occurred.
Recommended Action Copy the message exactly as it appears and report it to your technical service representative.
Error Message%ROUTING-MPLS_TE-3-ERR_SYSDB_DELETE [chars]: [chars]: [chars]
Explanation A SysDB free related error occurred.
Recommended Action Copy the message exactly as it appears and report it to your technical service representative.
Error Message%ROUTING-MPLS_TE-3-ERR_SYSDB_GET [chars]: [chars] failed for path [chars] : [chars]
Explanation A sysdb error occurred.
Recommended Action Copy the message exactly as it appears and report it to your technical service representative.
Error Message%ROUTING-MPLS_TE-3-ERR_TRACE_INIT Traffic-eng event tracing subsytem initialization failed
Explanation Traffic-eng could not initialize the tracing module
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_TE-3-LSP_UPDOWN [chars] (LSP Id: [unsigned int]) state changed to [chars]
Explanation The specified interface has changed operational state.
Recommended Action None. This is a solicited message (by 'logging event lsp-status state' interface configuration) and is informative only.
Error Message%ROUTING-MPLS_TE-4-SHOW_WARNING The show thread waited [unsigned int] seconds and could not acquire the mutex. Aborting show request. Please try again. If this problem persists, please contact your technical service representative.
Explanation The show thread could not acquire the mutex to service the show request. The main thread in te_control may be busy/blocked/hogging while holding That mutex.
Recommended Action Try to run the show command again. If the error reoccurs, then check the state of the te_control process (show process te_control). If thread number 1 is blocked for an extended period of time, contact your technical service representative.
Error Message%ROUTING-MPLS_TE-4-SHUTDOWN Process is shutting down ([chars]): [chars]
Explanation TE process has encountered a problem which means it is no longer able to continue and is shutting down. The message includes a brief description of the problem. The message also describes whether or not TE process has automatically been restarted.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Follow the instructions associated with this message. If message states that an automatic restart has been scheduled, then TE process will recover automatically. If a manual restart is required, then 'process start te_control' is required to recover.
Error Message%ROUTING-MPLS_TE-4-WARN [chars]
Explanation An internal system warning occurred.
Recommended Action Copy the message exactly as it appears and report it to your technical service representative.
Error Message%ROUTING-MPLS_TE-4-WARNING_FSM_EVENT_DROP Traffic-eng FSM dropped an event ([chars]) for S2L (tid [unsigned int], etid [unsigned int], lspid [unsigned int], p2mpid [unsigned int], subgroupid [unsigned int])
Explanation Traffic-eng FSM dropped an event, because the S2L was created after the event was posted.
Recommended Action Copy the message exactly as it appears and report it to your technical service representative.
Error Message%ROUTING-MPLS_TE-5-FRR Backup Tunnel ([chars], LSP Id: [unsigned int]) state changed to [chars].
Explanation The specified backup tunnel interface has changed it's FRR status.
Recommended Action None. This is a solicited message (by 'logging events frr-protection' interface configuration) and is informative only.
Error Message%ROUTING-MPLS_TE-5-LSP_REOPT [chars] (LSP Id: [unsigned int]) has been reoptimized.
Explanation The specified interface has been reoptimized with the specified LSP.
Recommended Action None. This is a solicited message (by 'logging event lsp-status reopt' interface configuration) and is informative only.
Error Message%ROUTING-MPLS_TE-5-LSP_REROUTE [chars] (LSP Id: [unsigned int]) has been fast-rerouted.
Explanation The specified interface has been rerouted.
Recommended Action None. This is a solicited message (by 'logging event lsp-status reroute' interface configuration) and is informative only.
Error Message%ROUTING-MPLS_TE-7-ERR_IM [chars]: [chars] failed, some tunnel-te interfaces were not created properly
Explanation An Ifmgr error occurred.
Recommended Action Copy the message exactly as it appears and report it to your technical service representative.
Error Message%ROUTING-MPLS_TE-7-ERR_INTERNAL [chars] : [chars]
Explanation An internal system error occurred.
Recommended Action Copy the message exactly as it appears and report it to your technical service representative.
MRIB_API Messages
Error Message%ROUTING-MRIB_API-3-ASYNC_ERR Asynchronous error: [chars]
Explanation 'An unhandled asynchromous error occurred in the MRIB API'
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB_API-3-CORRPT Corrupted update: [chars]. (expected [dec] bytes, got [dec] bytes)
Explanation 'A corrupted update was received from the MRIB by the MRIB API'
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB_API-3-GEN_ERR [chars]%s
Explanation Error occurred in mrib client lib.
Recommended Action No action is required.
Error Message%ROUTING-MRIB_API-3-GENINITFAIL Initialization failed: [chars] [chars]
Explanation Error occurred at client initialization.
Recommended Action No action is required.
Error Message%ROUTING-MRIB_API-3-RPC_FAIL RPC failure: [chars]
Explanation 'An RPC-related error occurred in an RPC call from the MRIB API'
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB_API-7-ASYNC_WAR Warning: [chars]
Explanation 'A recoverable error condition occurred in the MRIB API'
Recommended Action No action is required.
MRIB Messages
Error Message%ROUTING-MRIB-2-NOMEMORY [chars]No memory for [chars] in [chars]
Explanation The requested operation could not be accomplished because of a low memory condition.
Recommended Action This indicates a low memory condition. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-MRIB-2-NORESOURCE Resource unavailable for [chars] in [chars]
Explanation The requested operation could not be accomplished because of a low memory condition.
Recommended Action This indicates a low memory condition. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-MRIB-2-RC_INIT_ERR Route collapse IPC Init failed at [chars]!
Explanation The route collapse IPC could not be initialized
Recommended Action This is a fatal error. Process does not recover currently. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-EDM_INIT Error in EDM activity : [chars] - [chars]
Explanation An error occurred when MRIB tried to initialize conn to Sysdb for show commands.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-EXTRANET_ERR [chars]
Explanation An error occurred in MRIB MVPN EXTRANET operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-GEN_ERR [chars]%s
Explanation A general error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-GENCOMMERR Communication error: [chars] [chars]
Explanation A Inter Process Communication error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-GENINITFAIL Initialization failed: [chars] [chars]
Explanation An unrecoverable error occurred at system initialization time.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-IFCACHE_ERR [chars]
Explanation An error occurred in MRIB interface cache operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-INTERNALERR Internal error: [chars] in [chars] line [dec] ([chars])
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-LRD_ERR LRD Error: [chars] - [chars]
Explanation A general error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-LWM_ERR MRIB LWM error: [chars] - [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-MOD_INTF_LIST Interface [chars] has no modified flags. Shouldn't be present in list.
Explanation An error occurred when MRIB tried to walk the modified interfaces list.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-NSF_ERR [chars]
Explanation An error occurred in MRIB NSF.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-NSFSTATE Error modifying MRIB Non-stop Forwarding state in [chars]: [chars]
Explanation An internal error occurred when MRIB attempted to transition to/from Non-stop Forwarding mode.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-RC_ERR [chars]
Explanation An error occurred in MRIB route collapse operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-REDUCEDFUNCT Initialization of [chars] functionality failed
Explanation The initialization of a functionality failed. This component migh still operate without the functionality.
Recommended Action This indicate a resource shortage. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-MRIB-3-TLC_ERR [chars]
Explanation An error occurred in MRIB TLC operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-TREE_OPER Failed to [chars] [chars] interface in interface tree of [chars].
Explanation An error occurred when MRIB tried to perform a tree operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-4-CLIENT_WRITE Client [CCB ID [dec]]. Update size equals [dec] bytes. [chars]
Explanation A client attempted to write an invalid update.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-4-DEBUGERR Debugging error: [chars] in [chars] line [dec] ([chars])
Explanation An error related to the debugging subsystem occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-4-FILTRVIOLERR Filter violation error: conn [dec] ([chars]:[chars]) in [chars]
Explanation A client tried to modify a route attribute not owned by it
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-4-GEN_WARN [chars]
Explanation A general warning.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-4-INCORRECTPARS Illegal parameter in function call ([chars]) in [chars]
Explanation An externally accessible function has been called with illegal parameter(s). the parameter(s) has been casted to an acceptable value.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-4-NOMEMORYW No memory for [chars] in [chars]. Handling: [chars]
Explanation The requested operation could not be accomplished because of a low memory condition but the problem has ben handled locally.
Recommended Action This indicates a low memory condition. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-MRIB-4-STALE_HANDLE_ERR [chars]%s
Explanation A pfi query was made for a stale interface handle, possibly transient error.
Recommended Action No action is required.
Error Message%ROUTING-MRIB-5-BCDL_ERR Failed to [chars]: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MSDP Messages
Error Message%ROUTING-MSDP-3-ACL_ERR acl error: [chars] [chars] [chars]
Explanation Check if access list is configured as intended
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-MSDP-3-BAD_STATE the peer [chars] has changed to an illegal state: [dec]
Explanation The state was not one of the valid states
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-CACHE_ERR cache error: [chars] [chars]
Explanation An error occured updating the SA cache.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-CONNECTION_ERR [chars] error: [chars]
Explanation A peer has incorrectly attempted to establish a connection with us. Possible causes may include a passive peer trying to make an active connection, in this case the connection will be rejected. Recieving a connection request from a peer that is in the Established state, in this case the current, if the peer is active, the existing connection will be terminated and the new connection will be acted upon. recommended_action: Gather as much relavent information from the respective peer. *SUPPORT*
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-EDM_ERR error: show server error: [chars] [chars]
Explanation An error occured with a show client communicating with the msdp. show server.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-EVENT_FAILED event [chars] failure: [chars]
Explanation An unrecoverable error occurred during the event loop.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-IARM_REG_ERR Failed to register on interface [chars]: [chars]
Explanation An error occured when registering to IARM.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-IARM_UPDATE_ERR Failed to update: [chars]
Explanation An error occured when registering to IARM.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-INIT_FAILED Initialization failed: [chars]
Explanation An unrecoverable error occurred at system initialization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-INIT_FAILED2 Initialization failed: [chars], [chars]
Explanation An unrecoverable error occurred at system initialization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-INTERNAL_STATE_ERR [chars]: [chars] [chars]/[chars]
Explanation An error occured due to inconsistent internal state.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-IO_FAILED I/O failure: [chars] [dec], [chars], [chars]
Explanation An error has occurred during a socket operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-LPTS_POLICY_ERR Failed to [chars] lpts policy for peer [chars] [[dec]]
Explanation Some socket/lpts error occured.
Recommended Action Consult the configuration documentation for appropriate commands.
Error Message%ROUTING-MSDP-3-LTRACE_INIT ltrace_init failed for '[chars]': [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-MRIB_ERR mrib error: [chars], [chars]
Explanation An error has occurred during communication with the MRIB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-NOTIFY [chars] notification [chars]: code: [dec], subcode [dec]
Explanation An error was encountered during communication with specified peer.
Recommended Action Observe error details to determine cause of problem. If that does not help turn on 'debug ip msdp tlv'.
Error Message%ROUTING-MSDP-3-OUT_OF_MEMORY out of memory: [chars] [chars]
Explanation Eliminate system processes or add memory
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-MSDP-3-OUT_OF_RESOURCE [chars] active SA limit [dec] exceeded SA count
Explanation Resource limit has been hit
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-MSDP-3-SOCKET_ERR socket([dec]) error: [chars] [chars]
Explanation An unrecoverable error occured during a socket operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-SYSDB_ERR sysdb error: [chars] [chars]
Explanation An error occured while communicating with sysdb.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-WDSYSMON_EVENT_ERROR Received an invalid event from WDSysmon
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-WDSYSMON_REGISTER_ERROR [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-4-BAD_MASKLEN invalid mask length, must be 32 ([chars]/[dec]): [chars]
Explanation A masklen other than 32 was attempted'
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-4-BGP bgp client: [chars] [chars]
Explanation Problem communicating with BGP
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-4-CONFIG_FAILED config failed: [chars] [chars], [chars]
Explanation 'reconfigure'
Recommended Action Consult the configuration documentation for appropriate commands.
Error Message%ROUTING-MSDP-4-MRIB_WARN warning mrib: [chars]: [chars]
Explanation An problem comminicating with the mrib.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-4-OOM_STATE_THROTTLE Received [chars] memory depletion warning, stop creating new msdp SA state
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-4-OOM_STATE_UNTHROTTLE Node memory back to normal, new msdp states will be created
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-4-PEER_ERR peer error: [chars] [chars]
Explanation Some peer error occured.
Recommended Action Consult the configuration documentation for appropriate commands.
Error Message%ROUTING-MSDP-4-RIB_ERR rib error: [chars] [chars]: [chars]
Explanation An error has occurred during communication with the RIB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-4-SA_MESSAGE [chars]: error in SA ([chars], [chars]): [chars]
Explanation Error in the SA message format or contents.
Recommended Action Turn on 'debug ip msdp tlv' for more information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-4-TIMER timer error has occured
Explanation A timer error has occur
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-5-INIT_PEER_UP_DOWN [chars] [chars] [chars]
Explanation MSDP Peer UP/DOWN.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-6-INIT_BASIC [chars]: pid [dec]
Explanation MSDP Initialized.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-6-INIT_INFO retried [chars] [chars] [dec]
Explanation An unrecoverable error occurred at system initialization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MULTIVER Messages
Error Message%ROUTING-MULTIVER-3-ERR_DLL_OPEN Could not load DLL [chars]: [chars]
Explanation There was a problem loading the DLL - perhaps the router has run out of memory, or there was a problem reading the file.
Recommended Action Check to make sure that one or more nodes is not having problems with memory.
Error Message%ROUTING-MULTIVER-4-DLL_SIGNATURE_MISMATCH Could not locate DLL [chars]([chars]), using [chars]([chars])
Explanation There was a problem locating the DLL with matching signature - the problem is resolved by using existing dll installed on this node.
Recommended Action Check to make sure that there is no disparity in software installation across multiple nodes.
NTPD Messages
Error Message%ROUTING-NTPD-5-ALL_CONN_LOST All NTP peer connections failed.
Explanation The ntp server lost all connections with the clock sources.
Recommended Action No action is required.
Error Message%ROUTING-NTPD-5-HP_CONN_LOST High priority NTP peer connection lost.
Explanation The ntp server lost the connection with the best clock source configured.
Recommended Action No action is required.
Error Message%ROUTING-NTPD-5-HP_CONN_RECOVERED High priority NTP peer connection recovered.
Explanation The ntp server recovered the connection with the best clock source configured.
Recommended Action No action is required.
Error Message%ROUTING-NTPD-5-LP_CONN_RECOVERED At least a low priority NTP peer connection was recovered.
Explanation The ntp server recovered a connection with one of the configured clock source.
Recommended Action No action is required.
Error Message%ROUTING-NTPD-5-PEER_CLEAR NTP Peer [[chars]] cleared : [chars]
Explanation The NTP peer was cleared due to: 1. Peer unreachable. 2. Received peer ntp packet possibly bogus 3. Peer clock stepped 4. Peer clock reset 5. EDM server got 'clear all peers'
Recommended Action No action is required.
Error Message%ROUTING-NTPD-5-SYNC_LOSS Synchronization lost : [chars] : [chars]
Explanation NTP lost synchronization due to the mentioned reason in the argument passed. The reasons include: 1. The clock was stepped and needs to be resynced 2. Local clock was reset by more than 10 mins 3. No surviving peer after examining all possible reference sources. 4. Configured system peer was removed 5. A peer candidate was cleared
Recommended Action No action is required.
Error Message%ROUTING-NTPD-5-UNUSUAL_OFFS detect an unusual offset time value.
Explanation The offset between the active clock source and the system clock exceeds 1000 seconds.
Recommended Action No action is required.
ORA_SHARED Messages
Error Message%ROUTING-ORA_SHARED-4-ERR_DLL_REG Unable to register cerrno dll [chars] because [chars]
Explanation The given cerrno dll could not be marked for use. This does not change the functionality of the system but does obscure the meaning of error codes presented by this part of the system.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
ORA Messages
Error Message%ROUTING-ORA-2-ERR_MEM_ALLOC Cannot allocate entry
Explanation The requested operation could not be accomplished because of a low memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ORA-3-DUPLICATE_DOCKENTRY Dock entry add failure
Explanation I really do not know.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-3-INIT Failure in init function in DLL [chars]
Explanation The library is incorrectly installed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-3-MISSING_BASE_TYPE The base type '[chars]' v'[chars]' was used as a [chars] in a [chars]: '[chars]' type in area [chars]
Explanation One of the operations in one of the ORAs used a base type that was not defined in any of the ORA math sets.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-3-MISSING_FUNCTION Route access library [chars] has no [chars] function
Explanation The library is incorrectly installed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-3-MISSING_OPERATOR The operator '[chars]' was not located in any of the '[chars]'s ORAs.
Explanation There is a function declared within the various docked ORAs at this attach point that uses an operator that does not exist with the same set of docked ORAs. Please contact support.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-3-THREADING Threading operation '[chars]' for '[chars]' failed because: [chars]
Explanation The presented threading operation failed. It is likely that policy multi-version calls will stop working and thus policy may not be operational.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-4-ERR_DLL_REG Unable to register cerrno dll [chars] because [chars]
Explanation The given cerrno dll could not be marked for use. This does not change the functionality of the system but does obscure the meaning of error codes presented by this part of the system.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-4-MERGE_FAILED Some base type(s) was(were) unavailable during AP merging at: [chars]
Explanation One or more base types where not available when bringing together the parts of this attach point. This is an item that should be caught during testing. If it does show up, support should be contacted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-4-MISSING_DOCK_INFO The dock data for docking item [chars] was missing
Explanation This is most likely an internal logic error that resulted in a given ora dockling being released more than once.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-7-DBGINIT Unable to bring up debug event structures: [chars]
Explanation The debug event initialization failed. The ora docker will still run correctly, but debug commands may be unavailable.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-7-DBGSHUTDOWN Unable to shutdown debug event structures: [chars]
Explanation The debug event shutdown failed. The ora docker will still run correctly, but debug commands may be unavailable.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
OSPF_EDM Messages
Error Message%ROUTING-OSPF_EDM-3-DATALIST_ADD_FAILED Failed to add an external data manager datalist for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The attempt to add an item to an external data manager datalist has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_EDM-3-DATALIST_CREATE_FAILED Failed to create external data manager datalist for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The creation of the external data manager datalist has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_EDM-3-DATALIST_SET_MORE_FLAG Failed to set external data manager more flag for datalist [chars]
Explanation A client has requested information through SysDB from OSPF. During execution of the request an attempt to set a flag indicating there is more data for the client failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_EDM-3-ENCODE_FAILED Failed to encode [chars] data in external data manager
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The data requested could not be encoded.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_EDM-3-LIST_ADD_FAILED Failed to add to an external data manager list for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The attempt to add an item to an external data manager list has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_EDM-3-LIST_CREATE_FAILED Failed to create external data manager list for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The creation of the external data manager list has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_EDM-3-SYSDB_BIND_FAILED Failed to connect to SysDB ([chars])
Explanation The process failed to connect to SysDB while starting.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
OSPF_POLICY Messages
Error Message%ROUTING-OSPF_POLICY-3-ORA_INSTBUILD Failed to build [chars], reason [chars] cer [chars]
Explanation Internal error in policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_POLICY-3-ORA_RUN Could not apply policy operation [chars] to attribute [chars] because [chars]
Explanation Internal error in policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
OSPF_RIB Messages
Error Message%ROUTING-OSPF_RIB-3-ERR_PATH_ADD Error adding path to batching buffer
Explanation An error was encountered in the call to ipv4_rib_batch_add_path.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-3-ERR_PATH_DELETE Error deleting path from batching buffer
Explanation An error was encountered in the call to ipv4_rib_batch_delete_path.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-3-ERR_PROTO_MODIFY Error changing purgetime
Explanation An error was encountered in the call to ipv4_rib_protocol_modify.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-3-ERR_ROUTE_HDR Error adding route header to batching buffer for [chars]/[dec]
Explanation An error was encountered in the call to ipv4_rib_batch_add_route.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-3-ERR_UPDATE_DONE Error informing rib that batch is complete
Explanation An error was encountered in the call to ipv4_rib_batch_complete.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-4-BATCH_LOG_PATH RIB batch error, [chars] (result [dec]), prefix [hex]/[dec] next_hop [hex] intf [chars].
RetryingExplanation The specified error was encountered in the OSPF RIB batching code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-5-BATCH_ERROR RIB batch error, [chars]
Explanation The specified error was encountered in the OSPF RIB batching code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-5-BATCH_ERROR_CODE RIB batch error, [chars] ([hex])
Explanation The specified error was encountered in the OSPF RIB batching code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-6-INFO_RT_HDR_NOTUSED Believes [chars]/[dec] and [chars]/[dec] differ
Explanation The RIB batching API believes that it already has this router header in the batching buffer.
Recommended Action No action is required.
OSPF_UV Messages
Error Message%ROUTING-OSPF_UV-3-CERR_REG_FAIL Failed to register internal error codes: [chars]
Explanation An error occurred during the registration of OSPF error codes.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_DBG_REGISTER_FAILED Error initializing ospf_uv debugging: [chars]
Explanation An error occurred during initialization of the ospf_uv process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_MEM_ALLOC_FAIL Unable to allocate [unsigned int] bytes for '[chars]'
Explanation The ospf_uv process was unable to allocate memory for the specified resource.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_PROC_READY Error signaling process ready: [chars]
Explanation The ospf_uv process was unable to signal process ready to sysmgr.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_SYSDB_CONNECT Error binding to SysDB: [chars]
Explanation The ospf_uv process was unable to bind to SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_SYSDB_DISCONNECT Error unbinding from SysDB: [chars]
Explanation The ospf_uv process was unable to unbind from SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_SYSDB_REG_VERIFY Error registering with SysDB: [chars]
Explanation The ospf_uv process was unable to register with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_VRFN_FNS_INIT Error setting SysDB callback functions: [chars]
Explanation The ospf_uv process was unable to initialize SysDB callbacks.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-EVENT_ERR Error in event loop: [chars]
Explanation An error occurred in the main ospf_uv event loop.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-EVM_CRE_FAIL Error creating event connection manager: [chars]
Explanation The ospf_uv process was unable to create an event connection manager instance.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-INTF_FWS_INIT Error initializing forward-reference store: [chars]
Explanation The ospf_uv process was unable to initialize the forward-reference store library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-6-PROCESS_NAME Caution: The OSPF process name [chars] conflicts with a show or clear command name
Explanation The name chosen for the OSPF process matches an ospf show or clear command, or a command abbreviation. This can cause ambiguities with subsequent show or clear commands for this process.
Recommended Action Choose a different name for the OSPF process.
OSPF Messages
Error Message%ROUTING-OSPF-2-ERR_MEM_ALLOC No memory, [chars], process terminated
Explanation Memory allocation of a critical OSPF resource failed because of a low memory condition. The OSPF process was terminated.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-OSPF-3-ALLOC_ERR Allocation error, [unsigned int] bytes for [chars]
Explanation Allocation of the specified resource failed because of a low memory condition.
Recommended Action This indicates a low memory condition. Reduce other system activity to ease memory demands.
Error Message%ROUTING-OSPF-3-AREANULL [chars]: area pointer is NULL
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-BADMSG ospf router received bad message type [dec]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-BADSHARE Bad refcount at [hex] (refcount equals [hex]) in [chars]
Explanation An internal software error occurred. Resources may be in inconsistent state.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%ROUTING-OSPF-3-BADTIMER Managed Timer error, [chars]: Unrecognized timer type [dec]
Explanation A timer was found with an unrecognized type
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-DBGINIT Debug init error, [chars]: event [chars], error [dec]
Explanation Unable to initialize a debugging flag
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-DUP_RTRID OSPF detected duplicate router-id [chars] from [chars] on interface [chars]
Explanation OSPF received hello packet from a neighbor which has the same router-id as this routing process. A full adjacency cannot be established.
Recommended Action OSPF router-id should be unique. Change the neighbors router-id.
Error Message%ROUTING-OSPF-3-ERR_RESOURCE_ALLOC No memory could be allocated for the resource, [chars]
Explanation Allocation of the specified resource failed because of a low memory condition. This could affect the protocol functionality.
Recommended Action This indicates a low memory condition. Reduce other system activity to ease memory demands and preferably restart the OSPF process.
Error Message%ROUTING-OSPF-3-EVM External Event Manager error, [chars], error [chars] [[hex]]
Explanation A call to an external event manager function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-EVM_CODE External Event Manager error, [chars]: [chars] code [dec], error [chars] [[hex]]
Explanation A call to an external event manager function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-EVM_RL raw_conn momentarily not usable, [chars]
Explanation raw_conn not available to send the packet
Recommended Action If the condition persist, contact the technical support.
Error Message%ROUTING-OSPF-3-EXTERNALERR External error, [chars]
Explanation An external software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-EXTERNALERR_RC External error, [chars], error [hex]
Explanation An external software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-FRIS FRIS error, [chars], [chars] error [chars] [[hex]]
Explanation The FRIS request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-IDBERR IDB error, [chars]: [chars], intf [chars] cerr [chars]
Explanation Error encountered while attempting to activate an idb. Problem could be corrupt data from IM or IP/ARM or the FRIS.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-IFCHECK Interface [chars] is attached to more than one area
Explanation An internal consistency check has failed. An interface appears to be associated with more than one area.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-IFINIT Interface init error, interface [chars]
Explanation OSPF failed to initialize data structures for an interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-IFMGR External IFMGR error, [chars], intf [chars] error [chars] [[hex]]
Explanation The specified interface manager request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-IGPTE IGP/TE error, [chars]: [chars] error [dec]
Explanation Error encountered while attempting to use the IGP_TE Lib.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-INIT_ERR Init error, [chars], error [hex]
Explanation An error occurred during initialization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-INIT_ERR_STR Initialization failure, [chars], error [chars], process terminated
Explanation An error occurred during initialization, causing the process to terminate.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%ROUTING-OSPF-3-INTERNALERR Internal error, [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-INTERNALERR_RC Internal error, [chars], error [hex]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-IPARM External IP-ARM error, [chars], error [chars] [[hex]]
Explanation A call to an external IP-ARM function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-LWM External light-weight msg error, [chars], error [chars] [[hex]]
Explanation A call to an external light-weight messaging function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-MCAST Multicast error, [chars] [chars] on [chars], error [chars]
Explanation The above specified multicast operation failed
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-MEDIAERR Media error, [chars]: Interface [chars] unknown type: [chars]
Explanation Media table lookup failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-MUTEX Mutex error, [chars], [chars] mutex, error [chars] [[hex]]
Explanation An error occurred in the pthread functions used for thread synchronization. This is most likely a system error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-NOBACKBONE Flagged as being an ABR without a backbone area
Explanation The router was flagged as an Area Border Router (ABR) without backbone area in the router.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-NOIPADDR No IP Addr on interface [chars]. OSPF will not be run over it.
Explanation This message is displayed if ospf is configured on an unnumbered interface that is not of type point to point. In this case, ospf will not run on this interface.
Recommended Action No action is required.
Error Message%ROUTING-OSPF-3-NOSELF if [chars] if_state [dec]
Explanation An internal error occurred. An interface was not fully initialized when an OSPF related event occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-NOTNBRTYPE Cannot configure neighbor on [chars]. Interface must be NBMA or P2MP
Explanation Neighbor cannot be configured on interface if it is not type NBMA or point to multipoint.
Recommended Action No action is required.
Error Message%ROUTING-OSPF-3-PKTDROP Raw socket error, [chars]: packet dropped, [chars]
Explanation An input packet was dropped for the specified reason.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-RDB_NO_LSA lsid [chars] adv [chars] type [dec] gateway [chars] metric [dec] network [chars] mask [chars] attr [hex] net-metric [dec]
Explanation OSPF found inconsistency between its database and topology table.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-RECONF_VL OSPF process [chars] is changing router-id. Reconfigure virtual link neighbors with our new router-id
Explanation OSPF process is being reset, and it is going to select a new router-id. This will bring down all virtual links. To make them work again, virtual link configuration needs to be changed on all virtual link neighbors.
Recommended Action Change virtual link configuration on all the virtual link neighbors, to reflect our new router-id.
Error Message%ROUTING-OSPF-3-RIB External RIB error, [chars], error [chars] [hex]
Explanation A call to an external RIB function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-RIB_MSG External RIB error, [chars]
Explanation A call to an external RIB function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-RPC External RPC error, [chars], error [chars] [[hex]]
Explanation An RPC error occurred
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-SOCKET External socket error, [chars], error [chars] [[hex]]
Explanation The above specified socket operation failed
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-SYSDB External SysDB error, [chars], error [chars] [[hex]]
Explanation An external OSPF error occurred when accessing the system database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-THREAD_CREATE Thread create error, [chars], error [chars] [[hex]]
Explanation OSPF failed to create a thread essential to its operation. This is an internal error. An automatic restart of the OSPF process was necessary to attempt recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-UNKNOWNSTATE Reached unknown state in neighbor state machine
Explanation An internal software error occurred. When processing and DBD packet, the neighbor was found to be in an indeterminate state.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-BADLENGTH Invalid length [dec] in OSPF packet from [chars] (ID [chars]), [chars]
Explanation The system received an OSPF packet with a length field of less than normal header size or inconsistent with the size of the IP packet in which it arrived. This indicates an error in the sender of the packet.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-BADLSATYPE Invalid lsa: [chars] Type [dec], LSID [chars] from [chars], [chars], [chars]
Explanation The router received an LSA with invalid LSA Type. The cause is either memory corruption or unexpected behavior on a router.
Recommended Action Check both the sending and receiving routers for memory corruption. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-CONFLICTING_LSAID Found LSA with the same host bits but different mask.
LSA with shorter mask will be used.
LSA 1: [chars]/[dec]
LSA 2: [chars]/[dec]Explanation An LSA could not be generated because there is a supernet lsa with the host bit set LSA ID that conflicts with the major net LSA ID that also needs to have host bit set.
Recommended Action This is a limitation in OSPF's ability to handle conflicting LSA IDs. Attempt to avoid this limitation by modifying the generation of summary LSA's so that the LSA ID's do not conflict. Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-DEPRECATED_RTRID
outer-id [chars] command has been deprecated. Please delete
outer-id [chars] and reconfigure router-id.Explanation OSPF router-id interface has been deprecated.
Recommended Action Use router-id ipaddress.
Error Message%ROUTING-OSPF-4-DOMAIN_TAG_NEEDED Domain-tag must be configured with 4-byte AS number in vrf [chars]
Explanation At the time of the redistribution of BGP with 4 byte AS number, domain-tag wasn't confiured. User needs to be aware that in this case domain-tag must be configured.
Recommended Action If not already configured domain-tag should be configured for the vrf.
Error Message%ROUTING-OSPF-4-ERR_MSG_GET_SCOID Error retrieving client's connection ID to the [chars] channel: [chars] ([dec])
Explanation OSPF failed to retrieve its local connection ID for a client attached to the specified channel. This is an internal programming error.
Recommended Action Restart the OSPF process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-ERR_MSG_REPLY Error replying to the client [chars]: [chars] ([dec])
Explanation OSPF failed to reply to its client through message channel. This could be a result of channel down or resource allocation failure.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Restart the OSPF process. *RECUR*
Error Message%ROUTING-OSPF-4-ERRRCV Received invalid packet: [chars] from [chars], [chars]
Explanation An invalid OSPF packet was received. Details are included in the error message. The cause might be a misconfigured OSPF or an internal error in the sender.
Recommended Action Check the OSPF configuration of the receiver and the sender for inconsistency. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-IFINDEX_GET Unable to get interface index for [chars]: [chars]
Explanation An error occurred when trying to get a numeric interface index value for the specified interface. Ietf nsf restart might fail.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-KEYCFG Key [unsigned long int] [chars]
Explanation An error occurred when trying to configure an ospf authentication key.
Recommended Action No action is required.
Error Message%ROUTING-OSPF-4-MAX_INTF_APPLY Interface limit [dec] exceeded. Dropping interface [chars]
Explanation The number of interfaces configured exceeds the interface limit.
Recommended Action Either raise the maximum interface limit or unconfigure interfaces until the number is below the limit.
Error Message%ROUTING-OSPF-4-MAX_LSA Maximum number of non self-generated LSA has been exceeded [chars] - [dec] LSAs
Explanation Maximum number of non self-generated LSA has been exceeded
Recommended Action Check if some router in the network is generating large number of LSAs as a result of misconfiguration
Error Message%ROUTING-OSPF-4-MAX_LSA_THR Threshold for maximum number of non self-generated LSA has been reached [chars] - [dec] LSAs
Explanation Threshold for maximum number of non self-generated LSA has been reached
Recommended Action Check if some router in the network is generating large number of LSAs as a result of misconfiguration
Error Message%ROUTING-OSPF-4-MUTEX_ERR [chars] [chars] mutex ([hex]), tid [dec] owner [hex] count [dec], error [chars] [[hex]]
Explanation An error has been returned by the functions used for locking/unlocking an OSPF synchronization mutex.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-NBREXIST Neighbors were configured when NBMA or P2MP. Changing network type will abandon that configuration. Please remove configured neighbors.
Explanation Neighbors had been configured earlier when the network type was nonbroadcast. The current configuration request will cause these configured neighbors to be abandoned.
Recommended Action Remove the configured neighbors.
Error Message%ROUTING-OSPF-4-NETWORK_TYPE_MISMATCH Unexpected non-zero DR [chars] in hello packet from [chars]
Explanation OSPF has received a hello packet with non-zero Designated Router field on an interface that is not a multiaccess interface. Indicates a misconfiguration of network type among the OSPF routers in the given subnet.
Recommended Action Check the network type on all OSPF routers in the given subnet.
Error Message%ROUTING-OSPF-4-NONEIGHBOR Received [chars] from unknown neighbor [chars], vrf [chars] vrfid [hex]
Explanation OSPF hello, database description, or database request packet was received, but the router could not identify the sender. This is a normal occurrance if a link flap occurs on the router receiving the packet.
Recommended Action This situation should correct itself. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-NORTRID OSPF process [chars] cannot start without a router id. Configure router-id with the
outer-id command.Explanation OSPF failed while attempting to allocate a router ID from the IP address of one of its interfaces as no suitable IP address was available.
Recommended Action Make sure that there is at least one interface that is up and has a valid IP address. If there are multiple OSPF processes running on the router, each requires a unique router ID. You must have enough 'up' interfaces so that each of them can obtain a router ID. It is highly recommended that you configure loopback interfaces or use the router-id configuration command to better control the selection of OSPF router IDs.
Error Message%ROUTING-OSPF-4-OLD_CMD Command [chars] has been upgraded by [chars]. Use the new command.
Explanation The command has been replaced by a newer command.
Recommended Action Use the new command inidicated in the message.
Error Message%ROUTING-OSPF-4-PAKMAN_EVENT Pakman event [chars] received, code equals [dec], [chars]
Explanation An error has occured and pak manager sent use an event. If we can't recover from the error (ABORT event), OSPF will exit.
Recommended Action This is an indication that error(s) has occured in pakman No specific actions are required for OSPF.
Error Message%ROUTING-OSPF-4-POLICYCONFIG An error was encountered configuring policy, [chars]: [chars]
Explanation A problem was encountered while setting up route policy configuration. Some of the routing policy may not have been configured correctly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-RAW_OUTPUT_ERR Raw socket output err: [chars], src equals [chars], dest equals [chars], if equals [chars], msglen equals [dec]
Explanation An error has occured when OSPF is in process of sending a packet to the the raw socket.
Recommended Action This is an indication that error(s) has occured in other components and it is impacting OSPF's ability send data. No specific actions are required for OSPF.
Error Message%ROUTING-OSPF-4-REDIST_FAILED OSPF was unable to configure redistribution for protocol [chars]
Explanation An error occurred while OSPF was setting up redistribution for the named protocol. The redistribution will not take place.
Recommended Action This may be due to lack of memory, or due to a RIB failure, or to an internal OSPF problem. It may help to restart the OSPF process.
Error Message%ROUTING-OSPF-4-REDIST_MAX_PFX Redistribution prefix limit has been reached - [dec] prefixes
Explanation We have reached the maximum number of redistributed prefixes
Recommended Action Check if redistribution of large number of prefixes is desired and has not been wrongly configured.
Error Message%ROUTING-OSPF-4-REDIST_THR_PFX Redistribution prefix threshold has been reached - [dec] prefixes
Explanation We have reached the threshold level of number of redistributed prefixes.
Recommended Action Check if redistribution of large number of prefixes is desired and has not been wrongly configured.
Error Message%ROUTING-OSPF-4-STUB_ASBR Router is currently an ASBR while having only one area which is a stub area
Explanation Router is configured as an ASBR but is only connected to a single stub area. This can waste resources since the router has nowhere to send the external LSAs that it is generating.
Recommended Action Check configuration and disable redistribution of routes into ospf if appropriate.
Error Message%ROUTING-OSPF-4-USING_OLD_RTRID OSPF process [chars] encountered an error while finding a new router ID. The old router ID [chars] is being used as an interim value. clear ip ospf process will force another attempt to find a valid router ID.
Explanation OSPF failed while attempting to allocate a router ID from the IP address of one of its interfaces due to an unexpected internal problem.
Recommended Action Use 'clear ip ospf process' to force another attempt to find a valid router ID. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-VIRTUAL_IN_NON_BACKBONE Virtual link information found in non-backbone area: [chars]
Explanation An internal error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-5-ADJCHG Process [chars], Nbr [chars] on [chars] in area [chars] from [chars] to [chars], [chars], vrf [chars] vrfid [hex]
Explanation An OSPF neighbor has changed state. The message describes the change and the reason for it. This message appears only if the log-adjacency-changes command is configured for the OSPF process.
Recommended Action No action is required.
Error Message%ROUTING-OSPF-5-HA_NOTICE Process [chars]: [chars]
Explanation Used for logging of HA events like process startup, entry and exit of NSF/GR or NSR procedures and related events.
Recommended Action No action required.
Error Message%ROUTING-OSPF-5-HA_NOTICE_START [chars]
Explanation First log upon process startup.
Recommended Action No action required.
Error Message%ROUTING-OSPF-6-BADCHKSUM Checksum Failure in database in area [chars] Link State Id [chars] Old Checksum [hex] New Checksum [hex]
Explanation OSPF has detected a checksum error in the database due to memory corruption.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-6-DBEXIST area [chars] lsid [chars] mask [chars] adv [chars] type [dec]
Explanation OSPF has a problem locating the LSA, which could lead to a memory leak.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-6-GRACEFUL_SHUTDOWN [chars]
Explanation Informs user of graceful shutdown events. User needs to be aware of these activities.
Recommended Action No action required.
Error Message%ROUTING-OSPF-6-HA_INFO Process [chars]: [chars]
Explanation Used for logging of HA events like process startup, entry and exit of NSF/GR or NSR procedures and related events.
Recommended Action No action required.
Error Message%ROUTING-OSPF-6-LSAREFRESH Process [chars] vrf [chars]: LSA refresh interval changed. Old: [dec] New: [dec]. May take 10 minutes for the new interval to be in effect.
Explanation User has changed the configuable LSA refresh interval.
Recommended Action No action required. This is an informational message.
Error Message%ROUTING-OSPF-6-MAXMETRIC_RUNNING Current max-metric on-startup timer is running. New timer will be used at next reload.
Explanation maximum-metric LSA origination setting was changed while the maximum-metric origination was still active. The change will not take effect until the next time the system is restarted.
Recommended Action No action is required.
Error Message%ROUTING-OSPF-6-MEM_NOTIF [chars] [chars].
Explanation An unexpected event from the system monitor was seen.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-6-MGDTIMER External Managed Timer error, [chars], error [chars] [[hex]]
Explanation An external managed timer support routine failed. The affect this error has on the proper operation of OSPF depends on where and when this error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-6-NEWLIMIT [chars] limit changed. Old: [dec] New: [dec]
Explanation User has changed the configuable resource limit.
Recommended Action No action required. This is an informational message.
Error Message%ROUTING-OSPF-6-NOTREDIST3 build_ex_route(): don't redistribute net [chars]/[dec], [chars] advertises it already
Explanation For information only. Another router with a greater router ID is advertising the same external LSA. This router will stop originating the LSA to eliminate the redundancy.
Recommended Action No action is required.
Error Message%ROUTING-OSPF-6-REFBW_CHG Reference bandwidth is changed. Please ensure reference bandwidth is consistent across all routers.
Explanation Informational message reminding the user that reference bandwidth should be consistent across all routers in the area.
Recommended Action No action is required.
Error Message%ROUTING-OSPF-6-USING_MSGDGST Message-digest is used when both it and cleartext password are configured
Explanation Inform user that when both a clear text password and message-digest key are configured the message-digest key will be used.
Recommended Action No action is required.
Error Message%ROUTING-OSPF-7-DB_EX_DQUEUE [chars]: Unexpected external ReadyQ count of 0, &db equals [hex], &rtr equals [hex]
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-7-DB_READY_Q InReadyQ flag set for external DB, db [chars] on rtr_rt [chars]
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-7-DLINK dld [chars] is NULL
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-7-DQUEUE Double link queue count is 0 before decrement, &queue equals [hex]
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-7-ERR_TUNNEL_INT TE IDB error, [chars], [chars] error [chars] [[hex]]
Explanation Error in creating a tunnel interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-7-INIT_FAIL Initialization failure, [chars], process terminated
Explanation An error occurred during initialization, causing the process to terminate.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%ROUTING-OSPF-7-VRF_DELETE VRF delete error [chars] [chars] [chars]
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
OSPFv3_EDM Messages
Error Message%ROUTING-OSPFv3_EDM-3-DATALIST_ADD_FAILED Failed to add an external data manager datalist for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The attempt to add an item to an external data manager datalist has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-DATALIST_CREATE_FAILED Failed to create external data manager datalist for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The creation of the external data manager datalist has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-EDMINIT Error initializing EDM thread: [chars]: [chars]
Explanation An error occurred during initialization of the EDM thread.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-ENCODE_FAILED Failed to encode [chars] data in external data manager
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The data requested could not be encoded.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-EVENT_REGISTRATION_FAILED Failed to connect to the event manager: [chars]
Explanation The process failed while attempting to connect to an event manager channel for the indicated subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-LIST_ADD_FAILED Failed to add to an external data manager list for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The attempt to add an item to an external data manager list has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-LIST_CREATE_FAILED Failed to create external data manager list for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The creation of the external data manager list has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-NO_DATA Data for [chars] is not available
Explanation The data needed for the specified OSPF show command was not available. This would occur for non-critical data such as trace or debug information.
Recommended Action No action is required.
Error Message%ROUTING-OSPFv3_EDM-3-PROTO_REG_FAILED Failed to register show protocol information : [hex], '[chars]'
Explanation OSPFv3 was unable to register for support of the show protocol command.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-REGISTER_FAILED Failed to register its [chars] external data manager, '[chars]'
Explanation The process failed when attempting to register its external data manager with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-SYSDB_BIND_FAILED Failed to connect to SysDB ([chars])
Explanation The process failed to connect to SysDB while starting the indicated subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-SYSDB_COID_FAILED Failed to convert during a conn to coid conversion
Explanation The process failed to convert a conn to a coid while starting the indicated subsystem. This generally can only occur when starting up.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-6-BAGREG_FAILED Failed to register its external data manager data blocks
Explanation The process failed while attempting to register its external data manager data blocks with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
OSPFV3_POLICY Messages
Error Message%ROUTING-OSPFV3_POLICY-3-ORA_INSTBUILD Failed to build [chars], reason [chars] cer [chars]
Explanation Internal error in policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFV3_POLICY-3-ORA_RUN Could not apply policy operation [chars] to attribute [chars] because [chars]
Explanation Internal error in policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
OSPFv3_RIB Messages
Error Message%ROUTING-OSPFv3_RIB-2-NO_MEMORY Unable to allocate space for rib batching buffer: No Memory
Explanation Insufficent memory to allocate buffer for RIB batching API'
Recommended Action This indicates a low memory condition. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-OSPFv3_RIB-3-BIND Unable to bind to the RIB
Explanation An error occurred on a request to bind to the RIB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-DEFAULT_REG Unable to register with the RIB to receive the default route: [chars]
Explanation An error occurred on a request to have the RIB send us route updates for the default route.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-DISCONNECT Error while disconnecting RIB Event connection
Explanation An error occurred during an attempt to tear down the RIB Event connnection.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-ERR_BATCH_COMPLETE Error informing rib that batch is complete
Explanation An error was encountered in the call to ipv6_rib_batch_buffer_complete.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-ERR_PATH_ADD Error adding path-add to batching buffer (#[hex])
Explanation An error was encountered in the call to ipv6_rib_batch_add_path.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-ERR_PATH_DELETE Error adding path-delete to batching buffer ([hex])
Explanation An error was encountered in the call to ipv6_rib_batch_delete_path.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-ERR_ROUTE_HDR Error adding route header to batching buffer for [chars]/[dec] ([hex])
Explanation An error was encountered in the call to ipv6_rib_batch_add_route.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-ERR_UPDATE_COMPLETE Error informing rib that update is complete: [chars]
Explanation An error was encountered in the call to ipv6_rib_update_complete.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-FINDPDB Unable to get a RIB handle for [chars] routes: [chars]
Explanation An error occurred on a request to find the handle for the specified type of routes.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-PURGE Error removing OSPFv3 routes from the IPv6 RIB: [chars]
Explanation An error was encountered in the call to ipv6_rib_purge_protocol.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-REDIST_REG Unable to register with the RIB to receive updates for [chars] routes: [chars]
Explanation An error occurred on a request to have the RIB send us route updates for the specified type of routes.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-REGISTER Unable to register OSPFv3 with the RIB: [chars]
Explanation An error occurred on a request to register the OSPFv3 protocol with the RIB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
OSPFv3_UV Messages
Error Message%ROUTING-OSPFv3_UV-3-CERR_REG_FAIL Failed to register internal error codes: [chars]
Explanation An error occurred during the registration of OSPFv3 error codes.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-ERR_DBG_REGISTER_FAILED Error initializing ospfv3_uv debugging: [chars]
Explanation An error occurred during initialization of the ospfv3_uv process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-ERR_MEM_ALLOC_FAIL Unable to allocate [unsigned int] bytes for '[chars]'
Explanation The ospfv3_uv process was unable to allocate memory for the specified resource.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-ERR_PROC_READY Error signaling process ready: [chars]
Explanation The ospfv3_uv process was unable to signal process ready to sysmgr.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-ERR_SYSDB_CONNECT Error binding to SysDB: [chars]
Explanation The ospfv3_uv process was unable to bind to SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-ERR_SYSDB_DISCONNECT Error unbinding from SysDB: [chars]
Explanation The ospfv3_uv process was unable to unbind from SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-ERR_SYSDB_REG_VERIFY Error registering with SysDB: [chars]
Explanation The ospfv3_uv process was unable to register with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-ERR_VRFN_FNS_INIT Error setting SysDB callback functions: [chars]
Explanation The ospfv3_uv process was unable to initialize SysDB callbacks.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-EVENT_ERR Error in event loop: [chars]
Explanation An error occurred in the main ospfv3_uv event loop.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-EVM_CRE_FAIL Error creating event connection manager: [chars]
Explanation The ospfv3_uv process was unable to create an event connection manager instance.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-INTF_FWS_INIT Error initializing forward-reference store: [chars]
Explanation The ospfv3_uv process was unable to initialize the forward-reference store library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-6-PROCESS_NAME Caution: The OSPFv3 process name [chars] conflicts with a show or clear command name
Explanation The name chosen for the OSPFv3 process matches an ospf show or clear command, or a command abbreviation. This can cause ambiguities with subsequent show or clear commands for this process.
Recommended Action Choose a different name for the OSPFv3 process.
OSPFv3 Messages
Error Message%ROUTING-OSPFv3-2-NOMEMORY No memory for [chars]
Explanation The requested operation could not be accomplished because of a low memory condition.
Recommended Action This indicates a low memory condition. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-OSPFv3-3-ACL_GET Unable to get prefix-list [chars]: [chars]
Explanation An error occurred when trying to get the named prefix-list.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-ACL_REG Unable to register prefix-list [chars]: [chars]
Explanation An error occurred when trying to register for changes to the named prefix-list.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-ALLOCFAIL [chars] allocation failed: [chars]
Explanation Allocation of the specified resource failed, probably due to low memory.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-APIERR Call to [chars] from [chars] returns: [chars]
Explanation A lower-level support function returned an unexpected status.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-BADMSG Router thread received an invalid message type: [dec]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-BADTIMER Unrecognized [chars] timer type [dec]
Explanation A timer was found with an unrecognized type
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-CERR_REGISTER Failed to register internal error codes: [chars]
Explanation An error occurred during the registration of OSPFv3 error codes.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-CONN_FAIL Unable to connect to server [chars] : [chars]
Explanation OSPFv3 was unable to open a connection to a server. This is an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-DBGINIT Debug event initialization failed: [chars]
Explanation Unable to initialize a debugging flag.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-DBGREG Debug registration failed: [chars]
Explanation Unable to initialize debugging flags. Debug commands will not function.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-DELVLINK Cannot delete virtual link, backbone is being deleted
Explanation The virtual link cannot be removed because OSPFv3 is in the process of deleting the backbone area. Try again later.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-DLINK dld [chars] is NULL
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-DUP_RTRID Detected duplicate router ID [chars] from [chars] on interface [chars]
Explanation OSPFv3 received hello packet from a neighbor which has the same router ID as this routing process. A full adjacency cannot be established.
Recommended Action OSPFv3 router ID must be unique. Change the router ID.
Error Message%ROUTING-OSPFv3-3-DUP_RTRID_AREA Detected router with duplicate router ID [chars] in area [chars]
Explanation OSPFv3 has received multiple router LSAs with our router ID.
Recommended Action OSPFv3 router ID must be unique. Change the router ID.
Error Message%ROUTING-OSPFv3-3-DUP_RTRID_AS Detected router with duplicate router ID [chars] in inter-area router LSA advertised by [chars]
Explanation OSPFv3 has received an inter-area router LSA with our router ID.
Recommended Action OSPFv3 router ID must be unique. Change the router ID.
Error Message%ROUTING-OSPFv3-3-EVENTBLOCK Event blocking error in [chars] thread: [chars]
Explanation An error occurred while a thread was blocked waiting for an event
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-EVM_FD Error obtaining the [chars] file descriptor: [chars]
Explanation A call to get the file descriptor associated with an event manager connection failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-EVM_RETRY Unable to set event manager retry values for the [chars] connection: [chars]
Explanation A call to the external event manager to set connection retry values failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-FRIS_INSERT Unable to insert interface [chars] in the forward reference list: [chars]
Explanation An error occurred when adding the interface to the forward-reference list.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-HELLOINIT Error initializing hello thread: [chars]: [chars]
Explanation An error occurred during initialization of the hello thread.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IFINDEX_GET Unable to get interface index for [chars]: [chars]
Explanation An error occurred when trying to get a numeric interface index value for the specified interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IFINIT Initialization failure for interface [chars]
Explanation OSPFv3 failed to initialize data structures for an interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IFMGR [chars] failed: [chars]
Explanation The specified interface manager request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IFMGR_IF [chars] failed for interface [chars]: [chars]
Explanation The specified interface manager request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-INIT Initialization failed [[chars]], process terminated
Explanation An error occurred during initialization, causing the OSPFv3 process to terminate.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-INSTALL_REG Unable to register for package installation notifications: [chars]
Explanation An error occurred when trying to register with the packaging subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-INSTALL_UNREG Unable to unregister for package installation notifications: [chars]
Explanation An error occurred when trying to unregister with the packaging subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-INTERNALERR Internal error: [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IPARM [chars] failed: [chars]
Explanation The specified IP/ARM request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IPARM_IF [chars] failed for interface [chars]: [chars]
Explanation The specified IP/ARM request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IPSEC_CLOSE Error terminating IPSec processing for interface [chars]: [chars]
Explanation An error occurred when trying to close an IPSec SA for the named interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IPSEC_DEBUG_INIT Unable to initialize ipsec debugging: [chars]
Explanation An error occurred when trying to initialize the ipsec debug commands.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IPSEC_INIT Error initializing IPSec support: [chars]%s
Explanation An error occurred when trying to initialize the OSPFv3 IPSec subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IPSEC_OPEN Error initiating IPSec processing for interface [chars]: [chars]
Explanation An error occurred when trying to open an IPSec SA for the named interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-LAS [chars] failed: [chars]
Explanation The specified Local Address Service request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-LAS_ADDR Interface [chars] does not have a link-local address assigned
Explanation The specified interface has not received a link-local address from the Local Address Service.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-LAS_IF [chars] failed for interface [chars]: [chars]
Explanation The specified Local Address Service request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-MCAST Multicast [chars] on [chars] failed: [chars]
Explanation The specified multicast operation failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-MEM_ALLOC_FAIL Unable to allocate [unsigned int] bytes for '[chars]'
Explanation OSPFv3 was unable to allocate memory for the specified resource.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-MUTEX_INIT Error [chars] for [chars] mutex: [dec]
Explanation A error occurred in the initialization of the primitives used for thread synchronization. This is most likely a system error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-NO_VL_ENDPOINT Unable to add host route for virtual link endpoint in area [chars]
Explanation No IPv6 address was available to use as an endpoint for a virtual link.
Recommended Action Configure a loopback interface with an IPv6 address and add it to the specified area.
Error Message%ROUTING-OSPFv3-3-NOBACKBONE Flagged as being an ABR without a backbone area
Explanation The router was flagged as an Area Border Router (ABR) without backbone area in the router.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-NOSELF Interface [chars] if_state [dec]
Explanation An internal error occurred. An interface was not fully initialized when an OSPFv3 related event occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-NOTNBRTYPE Cannot configure neighbor on [chars]: interface must be NBMA or P2MP
Explanation Neighbor cannot be configured on interface if it is not type NBMA or point to multipoint.
Recommended Action No action is required.
Error Message%ROUTING-OSPFv3-3-PKTDROP Packet dropped: [chars]
Explanation An input packet was dropped for the specified reason.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-PKTDROP_STR Packet dropped: [chars]: [chars]
Explanation An input packet was dropped for the specified reason.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-PROCINIT Error initializing OSPFv3 process: [chars]: [chars]
Explanation An error occurred during OSPFv3 process initialization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-RIB [chars] [chars]/[dec]: [chars]
Explanation An error occurred on a request to the RIB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-RIB_ERR_PROTO_MODIFY Failed to modify purgetime with V6 RIB. Old [dec] New [dec]: [dec]
Explanation An error occurred on a request to the RIB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-RTRINIT Error initializing router thread: [chars]: [chars]
Explanation An error occurred during initialization of the router thread.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-SOCKET Socket operation [chars] failed: [chars]
Explanation The specified socket operation failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-SYSDB SysDB error: [chars]([chars]): [chars]
Explanation An error occurred when accessing the system database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-SYSMGR [chars] failed: [chars]
Explanation An specified system manager request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-THREAD_CREATE Error starting [chars] thread: [dec]
Explanation OSPFv3 failed to create a thread essential to its operation. This is an internal error. An automatic restart of the OSPFv3 process was necessary to attempt recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-UCAST Unicast [chars] on [chars] failed: [chars]
Explanation The specified unicast filter operation failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-UNKNOWNSTATE Reached unknown state in neighbor state machine
Explanation An internal software error occurred. When processing and DBD packet, the neighbor was found to be in an indeterminate state.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-UNSUPPORTED_IFTYPE Unsupported interface type [chars]: [chars]
Explanation The interface type is not yet supported by OSPFv3.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-BADAREA Received invalid packet: Incorrect area number ([chars]) from [chars], [chars]
Explanation The system received an OSPFv3 packet with an area ID that does not match the area that the interface belongs to.
Recommended Action Check the OSPFv3 configuration of the receiver and the sender for inconsistency. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-BADLENGTH Received invalid packet: Incorrect length ([dec]) from [chars], [chars]
Explanation The system received an OSPFv3 packet with a length field of less than normal header size or inconsistent with the size of the IPv6 packet in which it arrived. This indicates an error in the sender of the packet.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-BADLSA Invalid LSA: [chars], Type [hex] LSID [unsigned int] from [chars], [chars], [chars]
Explanation The router received an invalid LSA. The cause is either memory corruption or unexpected behavior on a router.
Recommended Action Check both the sending and receiving routers for memory corruption. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-BADVERS Received invalid packet: Incorrect OSPF version ([dec]) from [chars], [chars]
Explanation The system received an OSPFv3 packet with an OSPF version field other than 3. This indicates an error in the sender of the packet.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-DEPRECATED_RTRID
outer-id [chars] command has been deprecated. Please delete
outer-id [chars] and reconfigure router-id.Explanation OSPFv3 router-id interface has been deprecated.
Recommended Action Use router-id ipaddress.
Error Message%ROUTING-OSPFv3-4-ERRRCV Received invalid packet: [chars] from [chars], [chars]
Explanation An invalid OSPFv3 packet was received. Details are included in the error message. The cause might be a misconfigured OSPFv3 or an internal error in the sender.
Recommended Action Check the OSPFv3 configuration of the receiver and the sender for inconsistency. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-LSDB_ERROR Database error: [chars], Type [hex] LSID [unsigned int] from [chars]
Explanation OSPFv3 detected an error with its link state database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-LTRACE_INIT Unable to initialize the ltrace buffer [chars]: [chars]
Explanation An error occurred when trying to create a buffer for tracing.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-NONEIGHBOR Received [chars] from unknown neighbor [chars] on [chars]
Explanation OSPFv3 hello, database description, or database request packet was received, but the router could not identify the sender. This is a normal occurrance if a link flap occurs on the router receiving the packet.
Recommended Action This situation should correct itself. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-NORTRID OSPFv3 process [chars] could not pick a router-id, please configure manually
Explanation OSPFv3 failed while attempting to allocate a router ID.
Recommended Action Use the 'router-id' command to specify a unique Router ID for this OSPFv3 process.
Error Message%ROUTING-OSPFv3-4-PKTDROP_WARN Packet dropped: [chars]
Explanation An input packet was dropped for the specified reason.
Recommended Action Such errors are possible during raw_ip restarts. If seen otherwise, these errors should be reported to SUPPORT.
Error Message%ROUTING-OSPFv3-4-POLICYCONFIG An error was encountered configuring policy, [chars]: [chars]
Explanation A problem was encountered while setting up route policy configuration. Some of the routing policy may not have been configured correctly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-REDIST_MAX_PFX Redistribution prefix limit has been reached - [dec] prefixes
Explanation We have reached the maximum number of redistributed prefixes
Recommended Action Check if redistribution of large number of prefixes is desired and has not been wrongly configured.
Error Message%ROUTING-OSPFv3-4-REDIST_THR_PFX Redistribution prefix warning threshold has been reached - [dec] prefixes
Explanation We have reached the warning threshold number of redistributed prefixes.
Recommended Action Check if redistribution of large number of prefixes is desired and has not been wrongly configured
Error Message%ROUTING-OSPFv3-4-SOCKET_WARN Socket operation [chars] failed: [chars]
Explanation The specified socket operation failed.
Recommended Action Such errors are possible during raw_ip restarts. If seen otherwise, these errors should be reported to SUPPORT.
Error Message%ROUTING-OSPFv3-4-STUB_ASBR Router is currently an ASBR while having only one area which is a stub area
Explanation Router is configured as an ASBR but is only connected to a single stub area. This can waste resources since the router has nowhere to send the external LSAs that it is generating.
Recommended Action Check configuration and disable redistribution of routes into OSPFv3 if appropriate.
Error Message%ROUTING-OSPFv3-4-USING_OLD_RTRID OSPFv3 process [chars] encountered an error while finding a new router ID. The old router ID [chars] is being used as an interim value.
Explanation OSPFv3 failed while attempting to allocate a router ID from the IPv4 address of one of its interfaces due to an unexpected internal problem.
Recommended Action Use 'clear ospfv3 process' to force another attempt to find a valid router ID. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-VIRTUAL_IN_NON_BACKBONE Virtual link information found in non-backbone area: [chars]
Explanation An internal error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-5-ADJCHG Process [chars], Nbr [chars] on [chars] from [chars] to [chars], [chars]
Explanation An OSPFv3 neighbor has changed state. The message describes the change and the reason for it. This message appears only if the log-adjacency-changes command is configured for the OSPFv3 process.
Recommended Action No action is required.
Error Message%ROUTING-OSPFv3-5-HA_NOTICE Process [chars]: [chars]
Explanation Used for logging of events like process startup, entry and exit of GR events.
Recommended Action No action required.
Error Message%ROUTING-OSPFv3-5-HA_NOTICE_START [chars]
Explanation First log upon process startup.
Recommended Action No action required.
Error Message%ROUTING-OSPFv3-6-AREA_DELETE Area [chars] is being deleted, please try later
Explanation The configuration command could not be accepted because OSPFv3 is in the process of deleting the specified area. Try again later.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-6-AREACREATE Error creating area [chars]: [chars]
Explanation An error was encountered when trying to create an area.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-6-BADCHKSUM Checksum Failure in database: area [chars] LSA type [hex] LSID [hex] adv rtr [chars]: Old Checksum [hex] New Checksum [hex]
Explanation OSPFv3 has detected a checksum error in the database due to memory corruption.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-6-RECONF_VL OSPF v3 process [chars] is changing router-id. Reconfigure virtual link neighbors with our new router-id
Explanation OSPF process is being reset, and it is going to select a new router-id. This will bring down all virtual links. To make them work again, virtual link configuration needs to be changed on all virtual link neighbors.
Recommended Action Change virtual link configuration on all the virtual link neighbors, to reflect our new router-id.
Error Message%ROUTING-OSPFv3-6-REFBW_CHG Reference bandwidth is changed. Please ensure reference bandwidth is consistent across all routers.
Explanation Informational message reminding the user that reference bandwidth should be consistent across all routers in the area.
Recommended Action No action is required.
PIM_NETIO Messages
Error Message%ROUTING-PIM_NETIO-3-DEBUG_ERR [chars] failed : '[chars]'
Explanation PIM Netio dll failed initialization or registration with the debugging subsystem. This resulted in the restart of NetIO process.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
PIM_POLICY Messages
Error Message%ROUTING-PIM_POLICY-3-ORA_INSTBUILD Failed to build [chars]: [chars] ([chars])
Explanation Internal error in the routing policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PIM_POLICY-3-ORA_ORABUILD Failed to build ORA[chars]: [chars] ([chars])
Explanation There was an internal error in the routing policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PIM_POLICY-3-ORA_RUN Could not apply policy operation [chars] to attribute [chars] because [chars]
Explanation Internal error in the routing policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
POLICY_REPOSITORY_DYNREG Messages
Error Message%ROUTING-POLICY_REPOSITORY_DYNREG-3-ADD Failed to add node location [chars] for protocol: [chars], version: [chars], ap_name: [chars] preventing successful registration for this item, because: [chars].
Explanation An error was encountered as the node location was being added to the attach point item. This will prevent the successful registration for this attach point and will leave this configuration space unverified with respect to policy configuration.
Recommended Action Restart the policy_repository process to remedy this situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_DYNREG-3-CREATE Failed to create the attach point data for dynamic registration item: [chars], because: [chars]
Explanation An error was encountered as attach point data was being created. This could cause problems with future configuration attempts, and it does indicate an internal inconsistency so it might be best to restart the policy_repository to try to clear this inconsistency.
Recommended Action Restart the policy_repository process to remedy this situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_DYNREG-3-DATA Failed to extract [chars] data for protocol: [chars], version: [chars], ap_name: [chars], because: [chars]
Explanation An error was encountered as data was being extracted for the registration of this attach point. As such, the registration failed and the verification of configuration related to this attach point registration will NOT be performed. Thus, configuration could be accepted but could be unable to be processed by the protocols.
Recommended Action Restart the policy_repository process to remedy this situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_DYNREG-3-DELETE Failed to delete the attach point data for dynamic registration item: [chars], because: [chars]
Explanation An error was encountered as attach point data was being deleted. This could cause problems with future configuration attempts, and it does indicate an internal inconsistency so it might be best to restart the policy_repository to try to clear this inconsistency.
Recommended Action Restart the policy_repository process to remedy this situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_DYNREG-3-DOCK Failed to dock the new data for protocol: [chars], version: [chars], ap_name: [chars], because: [chars]
Explanation An error was encountered as new attach point data was being docked. As a result, the new data has not been activated for this attach point. At this point is would be best to restart the policy_repository to try to clear this inconsistency.
Recommended Action Restart the policy_repository process to remedy this situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_DYNREG-3-FIND Failed to find data for protocol: [chars], version: [chars], ap_name: [chars], during a [chars] operation, because: [chars]
Explanation An error was encountered as we were looking up data for the above attach point. The operation in question do not succeed since we could not find this entry, and thus the policy_repository could be in an inconsistent state.
Recommended Action Restart the policy_repository process to remedy this situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_DYNREG-3-INSTALL Failed to install the new attach point data for protocol: [chars], version: [chars], ap_name: [chars], because: [chars]
Explanation An error was encountered as new attach point data was being swapped out for old data. As a result, the old data is either still activated, or NO data is activated for this attach point. As this point is would be best to restart the policy_repository to try to clear this inconsistency.
Recommended Action Restart the policy_repository process to remedy this situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_DYNREG-3-MODIFY Failed to find data for a [chars] for protocol: [chars], version: [chars], ap_name: [chars], because: [chars]
Explanation An error was encountered as we were looking up data for the above attach point. The operation in question did not succeed, and thus the policy_repository could be in an inconsistent state.
Recommended Action Restart the policy_repository process to remedy this situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_DYNREG-3-REGISTER Failed to register (for verification) to the attach point data for dynamic registration item: [chars], because: [chars]
Explanation An error was encountered as attach point data was being registered for verification. At this point is would be best to restart the policy_repository to try to clear this inconsistency.
Recommended Action Restart the policy_repository process to remedy this situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_DYNREG-3-SWITCH We have detected a condition where there are conflicting registration values for protocol: [chars], version: [chars], ap_name: [chars], and are swapping out the current values for new values. The data for this can be viewed by executing the appropriate bind point show command.
Explanation An error was encountered as the node location was being added to the attach point item. This will prevent the successful registration for this attach point and will leave this configuration space unverified with respect to policy configuration.
Recommended Action Restart the policy_repository process to remedy this situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_DYNREG-3-UNDOCK Failed to undock the old [chars] data for protocol: [chars], version: [chars], ap_name: [chars], because: [chars]
Explanation An error was encountered as old attach point data was being undocked for new data. As a result, the old data is either still activated, or NO data is activated for this attach point. As this point is would be best to restart the policy_repository to try to clear this inconsistency.
Recommended Action Restart the policy_repository process to remedy this situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_DYNREG-3-UNLOAD Failed to unload the old attach point data for protocol: [chars], version: [chars], ap_name: [chars], because: [chars]
Explanation An error was encountered as old attach point data was being unloaded for new data. As a result, the old data is either still activated, or NO data is activated for this attach point. As this point is would be best to restart the policy_repository to try to clear this inconsistency.
Recommended Action Restart the policy_repository process to remedy this situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_DYNREG-3-UNREGISTER Failed to unregister (for verification) the old attach point data for protocol: [chars], version: [chars], ap_name: [chars], because: [chars]
Explanation An error was encountered as old attach point data was being unregistered for new data. As a result, the registration for the old data is still activated for this attach point. As this point is would be best to restart the policy_repository to try to clear this inconsistency.
Recommended Action Restart the policy_repository process to remedy this situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
POLICY_REPOSITORY_EDM Messages
Error Message%ROUTING-POLICY_REPOSITORY_EDM-3-ERR_SYSDB_BAG_ENCODE Failed to encode [chars] data in external data manager
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The data requested could not be encoded.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_EDM-3-ERR_SYSDB_BIND Failed to connect to SysDB ([chars])
Explanation The process failed to connect to SysDB while starting the indicated subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_EDM-3-ERR_SYSDB_EDM_DATA_GENERATE Failed to generate [chars] data in external data manager
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The data requested could not be generated.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_EDM-3-ERR_SYSDB_EDM_LIST_ADD Failed to add to an external data manager list for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The attempt to add an item to an external data manager list has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_EDM-3-ERR_SYSDB_EDM_LIST_CREATE Failed to create external data manager list for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The creation of the external data manager list has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_EDM-3-ERR_SYSDB_EDM_REG Failed to register its external data manager
Explanation The process failed when attempting to register its external data manager with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_EDM-3-ERR_SYSDB_UNBIND Failed to unconnect to SysDB ([chars])
Explanation The process failed to disconnect from SysDB before starting the indicated subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_EDM-6-ERR_SYSDB_BAG_REG Failed to register its external data manager data blocks
Explanation The process failed while attempting to register its external data manager data blocks with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
POLICY_REPOSITORY Messages
Error Message%ROUTING-POLICY_REPOSITORY-3-ERR_MEM_ALLOC Failed to allocate resources for [chars]
Explanation The policy_repository process failed allocated memory for the operation specified.
Recommended Action The policy_repository process may function properly in the future but the operations associated with this configuration are likely in an inconsistent state. Restarting the policy_repository may correct the situation if the memory is being consumed by this process; otherwise restarting the procees that is consuming the memory may be advisable. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-POLICY_REPOSITORY-3-ERR_ORA_DOCK Failed to dock with ORA [chars], version equals [chars], location equals [chars], signature equals [chars], path equals [chars] because: [chars]. This will result in NO policy being monitored or processed for this client.
Explanation The policy_repository process, while trying to dock with the client ORA encountered an error.
Recommended Action Restart the policy_repository and/or client. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-3-ERR_SYSDB_BAG_DECODE An attempt is being made to decode item ([chars]) which failed ([chars])
Explanation The system is attempting to process a policy object set or named policy and cannot decode the object.
Recommended Action Look for out of resource conditions. If memory is low, then restart the policy_repository process and reapply the configuration. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-3-ERR_SYSDB_CONNECT Failed to connect to the system database at '[chars]' ([chars])
Explanation The policy_repository process failed to bind to the system database at the displayed bind point.
Recommended Action The policy_repository process must be restarted before it can function correctly. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-3-ERR_SYSDB_GET Failed to retrieve configuration item: [chars] (Reason: [chars])
Explanation The policy_repository process failed to retrieve an item from the system database.
Recommended Action The policy_repository process may function properly in the future but the operations associated with this configuration are likely in an incinsistent state. Consider restarting the process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-3-ERR_SYSDB_REG_NOTIFY Failed to register for database notifications at: [chars] (Reason: [chars])
Explanation The policy_repository process failed to register for notification of changes on the displayed database path.
Recommended Action The policy_repository process must be restarted before it can function correctly. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-3-ERR_SYSDB_REG_VERIFY Failed to register for database verifications at: [chars] (Reason: [chars])
Explanation The policy_repository process failed to register for verification of changes on the displayed database path.
Recommended Action The policy_repository process must be restarted before it can function correctly. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-3-INCONSISTENT Inconsistency detected: [chars] ([chars])
Explanation The user is trying to do an operation which encountered inconsistent state for a policy object
Recommended Action The policy_repository process may function properly in the future but the operations associated with this configuration are likely in an inconsistent state. Restarting the policy_repository may correct the situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-POLICY_REPOSITORY-4-CLEANUP Failed to clean up policy '[chars]' ([chars])
Explanation When deleting the specified policy, the policy_repository process encountered a problem. This could leave memory unfreed.
Recommended Action If the policy_repository process is using an excessive amount of memory, consider restarting it with 'proc restart policy_repository' to clean up any unused memory. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-4-ERR_SYSDB_DELETE Failed to remove policy [chars] (Reason: [chars])
Explanation The policy_repository process encountered an error while trying to remove the data for a deleted policy.
Recommended Action This can only occur when there are no references to the deleted policy in the first place, and therefore will not have any harmful effects. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-4-PARSER_DLL Policy parser DLL: [chars]: [chars]
Explanation A system call failed inside the routing policy parser DLL.
Recommended Action Try again: the failure might have been due to resource issues. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-4-RPL_EDIT RPL editor: [chars]
Explanation A system call failed inside the RPL editor program.
Recommended Action Try again: the failure might have been due to resource issues. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-4-SYSMGR_GET_NODE_STATE Failed to receive the [active/standby] state indication. Error: [chars]
Explanation An error occurred while trying to get the system [active/standby] state. A state of REDUNDANCY_UNKNOWN will be assumed. This process also registers for notification of changes to the [active/standby] state. Thus, the state can be determined by this means as well. Failure to receive notification for either one of these means could result in this process not functioning properly. Note: At least one of the processes in an active/standby pair must be active in order to assure proper functioning.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-7-ARG_MISMATCH Argument list mismatch for statement '[chars] [chars]' in policy [[chars]].
Explanation The user is trying to do an operation in which the number of arguments entered does not match the number of argument expected.
Recommended Action Correct the number of parameters that are passed in. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-7-ATTACHPOINT_ADD Failed to associate [chars] attach point item '[chars]' to policy [chars]. This will leave the policy repository in an inconsistent state.
Explanation The policy_repository process was not able to add the attach point to the policy in question. This means that the policy repository will not verify the statements in this policy against the attach point in question. This could allow statements to be added to the policy that (could) result in run time errors in the client at this attach point.
Recommended Action Restart the policy_repository process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-7-ATTACHPOINT_MISMATCH Failed to process [chars] attach point item '[chars]' because [chars]. This will leave the policy repository in an inconsistent state.
Explanation The policy_repository process was not able to extract the policy name OR id value for this attach point path. This means that the policies that are actually using this attach point will NOT be recorded and thus policies *could* be deleted while still in use.
Recommended Action Restart the policy_repository. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-7-ITEM_UNSUPPORTED The item of type [chars] and value ([dec]) is not recognized by the policy_repository.
Explanation The policy_repository process was not able to extract the the item for this type. Please add support to the policy_repository or remove support from the protocols.
Recommended Action This indicates and internal inconsistency between the policy_repository and the protocols. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-7-OBJECT_INIT Failed to initialize [chars]. Error ([hex]): [chars]
Explanation The policy_repository was atempting to initialize a data object and it failed.
Recommended Action Look for out of resource conditions. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-7-OBJECT_REBUILD Failed to rebuild the [chars] data. Error ([hex]): [chars]
Explanation The system was atempting to rebuild an object and it failed.
Recommended Action Look for out of resource conditions. The policy_repository will exit and restart. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-7-POLICY_TOO_BIG Policy [[chars]] contains a large number of statements and would cause the policy repository to exceed resource limits. The policy repository is now inconsistent with the running configuration. To regain consistency, rollback to the previous configuration for this policy.
Explanation The policy named is very long and/or complex, and in compiling it for execution, the policy repository exhausted resource limits. This was not detected by the usual checks at configuration verification time. Rather than crash, the policy repository is left with the previous configuration for this policy, if any.
Recommended Action Rollback the configuration operation to regain consistency between the running configuration and the policy respoitory. Then, rewrite the policy in question in a simpler form. It may help to make use of policies with parameters to reduce the total policy size. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-7-SETS_REBUILD Internal inconsistency rebuilding sets for policy [chars] (Reason: [chars])
Explanation The policy_repository process failed to rebuild the set references for the policy in question. This will result in an inconsistent state in the policy_repository and the process should be restarted. This could result in policies not functioning properly.
Recommended Action The policy_repository process should be restarted to clean up the internal inconsistency. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-7-VERIFY_APPLY Policy [[chars]] failed verification for use in policy [[chars]]
Explanation The policy_repository process, while verifying a change to a policy, encountered an error while checking the validity of the change in the policies that are applied by that policy.
Recommended Action Fix the offending argument in the applied policy so that it is accepted by the client (i.e. BGP, OSPF, etc.) Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
RASF Messages
Error Message%ROUTING-RASF-3-NO_BASE_COMPARE There was a missing base compare function for an ORA.
Explanation This is a logic error in the construction of one of the ORA entities. The compare for checking two different route values against each other was missing.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RASF-3-NO_CMP_RETRIEVER There was a missing compare retriever function for an ORA.
Explanation This is a logic error in the construction of one of the ORA entities. The function to actually perform the compare retriever operation was not defined.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RASF-3-NO_COMPARE There was a missing compare function for an ORA.
Explanation This is a logic error in the construction of one of the ORA entities. A compare function was missing at the 'per route' level of detail.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RASF-3-NO_RETRIEVER There was a missing retriever function for an ORA.
Explanation This is a logic error in the construction of one of the ORA entities. The function to actually perform the retriever operation was not defined.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RASF-3-NO_SETTER There was a missing setter function for an ORA.
Explanation This is a logic error in the construction of one of the ORA entities. The function to actually perform the setter operation was not defined.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RASF-4-ERR_DLL_REG Unable to register cerrno dll [chars] because [chars]
Explanation The given cerrno dll could not be marked for use. This does not change the functionality of the system but does obscure the meaning of error codes presented by this part of the system.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RASF-7-DBGINIT Unable to bring up debug event structures: [chars]
Explanation The debug event initialization failed. The rasf will still run correctly, but debug commands may be unavailable.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RASF-7-DBGSHUTDOWN Unable to shutdown debug event structures: [chars]
Explanation The debug shutdown failed. The rasf will still run correctly, but debug commands may be unavailable.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
RETRY Messages
Error Message%ROUTING-RETRY-4-DEBUG_INIT [chars] [dec] [chars] [chars]
Explanation Internal error. Retry debug library initilization failed
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
RIB_LIB Messages
Error Message%ROUTING-RIB_LIB-3-ERR_LOCK_FATAL [chars] Pthread [chars], unexpected fatal error [[chars]]
Explanation An unexpected fatal error occured when trying operate on a pthread lock.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB_LIB-3-FETCH_UPDATE Error fetching RIB update - [chars]
Explanation Unexpected error fetching a RIB update notification. See error message for more information.
Recommended Action Restarting the client process from which the errow was emitted, or the RIB server, may fix the problem. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RIB_LIB-4-ERR_POSSIBLE_CONNECTION_LEAK RIB client binding with a non-NULL connection handle. Potential client memory leak.
Explanation A client passed a pointer to rib_bind which points to a non-NULL connection. This implies a connection leak in the client code.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB_LIB-4-UNBIND Failed to [chars] during client unbind - [chars]
Explanation Unexpected error during client unbind operation. This may result in a resource leak.
Recommended Action If there is a evidence of a memory leak in the process which reported this error, restart that process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
RIB_QUERY_ORA Messages
Error Message%ROUTING-RIB_QUERY_ORA-3-CERRNO_REG Failure registering cerrno DLL with subsys num [unsigned int] and DLL name [chars]. Error: [chars] ([hex])
Explanation A failure occurred during the registration of the DLL for decoding error codes from the component. This may render certain codes unprintable, but otherwise has no negative impact.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RIB_QUERY_ORA-3-INSTBUILD Failed to build policy operation '[chars]' for attribute '[chars]'.[chars]%s ([hex])
Explanation There was an internal error in the routing policy library and as a result routing policy may not be applied correctly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RIB_QUERY_ORA-3-ORABUILD Failed to build ORA: [chars]; [chars] ([hex])
Explanation There was an internal error in the routing policy library and as a result routing policy may not be applied correctly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RIB_QUERY_ORA-3-RUN Could not apply policy operation '[chars]' to attribute '[chars]': [chars] ([hex])
Explanation There was an internal error in the routing policy library and as a result routing policy may not be applied correctly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
RIB Messages
Error Message%ROUTING-RIB-2-CHILD_PARENT_MISMATCH Child [chars] ([chars]) ([dec]) unregistering from Vrf: [chars] Tbl: [chars] Safi: [chars], table id [hex], is not caught up with parent. Route inconsistency possible
Explanation A RIB download client (typically bcdl_agent), unregistered from a table while it was out of sync with its parent. The number of routes may no longer be insync in all FIBs. If corresponding bcdl_agent restarted just before this message was seen, this error message can be ignored.
Recommended Action Restart the corresponding bcdl_agent process. *SUPPORT*
Error Message%ROUTING-RIB-2-PARENT_UNREGISTER Parent [chars] ([chars]) ([dec]) unregistering from Vrf: [chars] Tbl: [chars] Safi: [chars], table id [hex], it still has [dec] dependants, context [chars]
Explanation A RIB download client (typically bcdl_agent), unregistered from a table while it still has children referring to this table. The number of routes may no longer be insync in all FIBs. If corresponding bcdl_agent restarted just before this message was seen, this error message can be ignored.
Recommended Action Restart the corresponding bcdl_agent process. *SUPPORT*
Error Message%ROUTING-RIB-3-BATCH_PROTO_REG_FAILURE Protocol batch [chars] from client [dec] for table [hex] protocol [hex] failed: [dec]
Explanation An error has occured processing protocol register batch from a RIB client.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-CONVERGE_VERSION_MISMATCH Client [chars] has last signalled version [dec] which is less than the RIB version [dec] for Vrf: [chars] Tbl: [chars] Safi: [chars]
Explanation A client updated the RIB for convergence but not with the latest version as known by RIB. This will have delayed or prevented the convergence of the routing table, and hence the purging of any stale routes from the forwarding table.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-ERR_CHILD_REDIST_REQUESTS [chars] [dec], line [dec], client [chars] ([dec]) table [hex] Vrf: [chars] Tbl: [chars] Safi: [chars]
Explanation An unexpected error occured when trying to add a path to the next-hop database.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-ERR_DELETE Path delete failure for Table [hex], prefix [chars]/[dec], protocol [dec], intf [hex], tunnelid [dec], nexthop_table [hex], nexthop [chars]
Explanation An error occured when trying to delete a path from a route.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-ERR_LOCK_FATAL Pthread lock [chars], unexpected fatal error [[chars]]
Explanation An unexpected fatal error occured when trying operate on a pthread lock.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-ERR_LOOKUP Table [hex], prefix [chars]/[dec], intf [hex], unexpected lookup results in [chars]
Explanation An unexpected lookup error occured when trying to lookup a prefix.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-ERR_MEM_ALLOC Failed to allocate memory for RIB operations
Explanation Failed to allocate memory for RIB operations probably out of memory because of huge configuration or a memory leak.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-ERR_MEM_NHPATH [chars]
Explanation An unexpected error occured when trying to clear redist information for a client.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-ERR_MUTEX_FATAL Mutex [chars], context '[chars]', unexpected fatal error [[chars]]
Explanation An unexpected fatal error occured when trying to lock or unlock a RIB mutex.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-ERR_NH_ATTRIBUTE [chars]
Explanation An unexpected error occured, a nexthop which is a RIB-only nexthop should not have path information but has.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-ERR_NH_PACK [chars], table [hex]
Explanation An unexpected nh notification packing error occured.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-ERR_NH_PATH Could not add [chars] to nh db for Vrf: [chars] Tbl: [chars] Safi: [chars]
Explanation An unexpected error occured when trying to add a path to the next-hop database.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-ERR_REDIST_INFO_CLEAR [chars], table [hex], client [chars] [chars] ([dec])
Explanation An unexpected error occured when trying to clear redist information for a client.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-ERR_RIBIO Client [chars] [chars] warning [[chars]]
Explanation An unexpected but non-fatal error occurred when a client performed an input/output operation. See error message for more information.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-ERR_RSI [chars], [chars] [chars] id [hex], [chars]
Explanation An unexpected RSI error occured during a table creation/deletion/modification operation.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-ERR_TABLE_OPERATION [chars], table [hex] [chars]
Explanation Some type of table related error occurred.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-ERR_THREAD_POOL Thread pool [chars] unexpected fatal error [[chars]]
Explanation An unexpected fatal error during a RIB thread pool operation. See error message for more details.
Recommended Action If the error is due to lack of resources, attempt to free some up and then restart RIB. Otherwise Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RIB-3-EVENT_BOOLEAN_SET Failed to set [chars] event boolean to [chars]: [chars]
Explanation Unexpected error during event boolean set. This may result in unreleased memory resources in RIB server.
Recommended Action If there is evidence of a memory leak in the RIB server, restarting it should help alleviate the problem. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RIB-3-GO_ACTIVE Failed to transition from active to standby - [chars]
Explanation Fatal error handling node state transition to active.
Recommended Action The RIB process should have restarted automatically and then gone into active state successfully. If not, try manually restarting it. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RIB-3-GO_STANDBY Node state changed from active to standby - don't know what to do
Explanation Node role state regressed from active state to standby state. This is not currently supported by RIB.
Recommended Action If the node's role change from active to standby was not deliberate, Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RIB-3-IMPROPER_PREFIX_MASK_LEN Received improper prefix, mask length [chars]/[dec] from client: [chars] proto: [chars]%s for Vrf: [chars] Tbl Id: [hex]
Explanation A client sent a batch to RIB containing an invalid op code.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-INTERFACE_DB Interface database: failed to [chars] the entry for [chars] with table id [unsigned int]
Explanation The rib unexpectedly failed to update the interface - IP address database.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-INVALID_BATCH_OPERATION Received invalid batch operation from client: [unsigned int]
Explanation A client sent a batch to RIB containing an invalid op code.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-INVALID_BCDL_REGISTRATION BCDL client [chars] ([dec]) registering with parent [chars] ([dec]) which also has a parent
Explanation Invalid BCDL registration detected.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-INVALID_TABLE_ACCESS A client attempted to access invalid table: [hex]
Explanation A client attempted to access a RIB table that does not exist.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-LTRACE_INIT RIB ltrace init failed. Error initialising [[chars]] trace buffer. Process terminated : [chars]
Explanation The ltrace buffer could not be initialised
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-LWM_REPLY Failed to send reply to client - [chars]
Explanation Unexpected error sending reply to a RIB client.
Recommended Action Check for errors in the state of the routing table. If any problems are identified, restarting the client and/or RIB may help to fix the problem. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RIB-3-MAIN_INIT Main thread initialization failed [[chars]:[chars]]. Process terminated
Explanation An error occurred during main thread initialization, causing the process to terminate. Check the details of the error message for more information.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-MGMNT_INIT Management thread initialization failed [[chars]:[chars]]. Process terminated
Explanation An error occurred during management thread initialization, causing the process to terminate. Check the details of the error message for more information.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-NEXTHOPS_TRAVERSE Failed to unregister next-hops for client [chars] - [chars]
Explanation Unexpected error unregistering client next-hops. This may lead to a slow memory leak.
Recommended Action If RIB is leaking memory, try restarting it. *SUPPORT*
Error Message%ROUTING-RIB-3-NH_CLIENT Failed to insert client [chars]/[chars] for nexthop [chars]/[dec]
Explanation An unexpected error occured when trying to clear redist information for a client.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-NH_DB_ADD Could not add nexthop to nh db, error [chars]
Explanation An unexpected error occured when trying to clear redist information for a client.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-NH_INSERT_HEAP Cannot insert nh_entry into the heap, [chars]
Explanation An unexpected error occured when trying to clear redist information for a client.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-NSF_WARN Failed to allocate resources required for NSF [chars]
Explanation Unexpected resource error during NSF initialization. This may result in NSF failures.
Recommended Action Free some resources and restart RIB *SUPPORT*
Error Message%ROUTING-RIB-3-PREFIXES_FULL The route prefix table ([hex]) is full with [unsigned int] prefixes.
Explanation The route prefix table has become full--either because the table reached the configured maximum fill level, or a maximum of 2,000,000 prefixes are stored.
Recommended Action If the maxmimum configured number of allowed route prefixes is configured lower than the allowed maximum of 2,000,000, update the configuration to allow a larger number of route prefixes. This threshold is set using the 'maximum prefix {max_prefixes} {low_threshold_percentage}' command. This command can be set per virtual router (vrf) or for the main routing table.
Error Message%ROUTING-RIB-3-PURGE_TIMER_ALLOC Not enough memory to allocate purge timer for Protocol [chars] (Instance [chars])
Explanation Couldn't allocate a purge timer. Old routes for this protocol may not automatically get purge from the FIB table.
Recommended Action Free up some resources and restart the RIB. *SUPPORT*
Error Message%ROUTING-RIB-3-QSM_ADD_SERVICE RIB failed function qsm_add_service to add local service: [chars]
Explanation RIB failed to advertise it local channel during failed over.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-RUMP_NOTIFY Failed to notify RUMP of new protocol: [chars]
Explanation Failed to notify RUMP about a newly registered protocol. See error message for more details. The result is that routes from the new protocol will not be redistributed into the multicast table.
Recommended Action Restart the RUMP process. *SUPPORT*
Error Message%ROUTING-RIB-3-SHUTDOWN Process is shutting down: [chars]
Explanation The RIB process has performed a graceful shutdown and will be restarted.
Recommended Action Check to make sure the process has restarted. If not, restart manually Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RIB-3-SYSDB_FD_CLOSED RIB is closing sysdb EDM connection, fd: [dec]
Explanation This notification indicates that RIB component is closing the connection with sysdb. Ignore the log if RIB or sysdb is restarting.
Recommended Action If RIB or sysdb is not restarting while this message is logged check if RIB show commands are working. This message is added to catch this exact scenario.
Error Message%ROUTING-RIB-3-TIME_ERR Failed to get timestamp from kernel
Explanation A call to clock_gettime failed.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-3-UPDATE_TIMEOUT Client [chars] updated the RIB without signaling update completion for Vrf: [chars] Tbl: [chars] Safi: [chars]
Explanation A client updated the RIB without signaling update completion. This will have delayed the convergence of the routing table, and hence the purging of any stale routes from the forwarding table.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-4-INVALID_SYSDB_ERROR RIB received an unexpected error([dec]) from sysdb
Explanation RIB recevied an unexpected error number from sysdb API.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-4-OPAQUE_FLAG_MISMATCH Client [chars]adding opaque data of type [hex] for which it has not register to RIB
Explanation A client adding an opaque data type for which it did register to RIB.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-4-PREFIXES_BELOW_THRESHOLD The previously full route prefix table ([hex]) is no longer full and can accept more routes.
Explanation The route prefix table is no longer considered full. This warning is generated after a full route prefix table frees off some route prefixes.
Recommended Action *NONE*
Error Message%ROUTING-RIB-4-PREFIXES_REACHED_LOW_THRESHOLD The fill level for the route prefix table ([hex]) reached the low warning fill level of [unsigned int] prefixes.
Explanation This warning indicates the number of prefixes in the specified prefix table reached the configured fill threshold. This is an informational message that may be used to alert changing trends in the number of active prefixes. This threshold is set using the 'maximum prefix {max_prefixes} {low_threshold_percentage}' command. This command can be set per virtual router (vrf) or for the main routing table.
Recommended Action If this threshold is regularly reached, it may no longer convey the original meaning. Either increase the fill percentage for the prefix table, or increase the number of prefixes that can be stored in the table. Both of these options are updated in the using the 'maximum prefix' command.
Error Message%ROUTING-RIB-4-RECURSION_DEPTH_CHANGED Maximum recursion depth changed. Please restart process to take effect.
Explanation The maximum recursion depth has changed. In order for the new value to take effect, the process has to be restarted. This warning is generated to remind the the customer to restart the RIB processes.
Recommended Action restart the RIB
Error Message%ROUTING-RIB-4-SELECT_IGNORED Client [chars] on [chars] - File select input ignored
Explanation Internal notification error.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-4-SYSMGR_NODE_STATE Failed to retrieve node state from sysmgr: [chars]
Explanation Sysmgr returned a failover from a node state query.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-4-UNSUPPORTED_OOM_STATE Bad memory state received from wdsysmon ([dec])
Explanation A memory state transition notification was received from wdsysmon with an invalid state.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-4-WARN_UNEXPECTED_EXT_COMM [chars], [chars]/[dec] in table [hex]
Explanation A route has extended communities attached to it unexpectedly.
Recommended Action *SUPPORT*
Error Message%ROUTING-RIB-5-TABLE_NH_DAMPED Nexthops in Vrf: [chars] Tbl: [chars] ([hex]) Safi: [chars] are getting damped
Explanation This notification indicates that there is atleast one nexthop in this RIB table that is getting damped.
Recommended Action *DEBUG*
Error Message%ROUTING-RIB-6-INFO_LOCKING_CONTEXT_DISPLAY Rib locking context[[dec]] [chars], operation: [chars], thread id: [dec]
Explanation Display a single entry of locking context information. The cause of this informational message should be evident from the context in the log.
Recommended Action *DEBUG*
Error Message%ROUTING-RIB-7-INFO_LOCKING_OPERATION_DISPLAY [chars] in function [chars]
Explanation Display the operation being performed on lock, and the function the operation is taking place in. This will only be displayed in verbose locking debugging.
Recommended Action *DEBUG*
Error Message%ROUTING-RIB-7-SERVER_ROUTING_DEPTH Recursion loop looking up prefix [chars] in Vrf: [chars] Tbl: [chars] Safi: [chars]
Explanation Recursive route lookup for resolving the prefix has exceeded the maximum recursion depth allowed(possibly because of a routing loop).
Recommended Action To further debug/troubleshoot this state use commands like 'show route' and 'show route resolving-next-hop' recursively to resolve the prefix manually, notice if there are any loops indeed.
RIP_POLICY Messages
Error Message%ROUTING-RIP_POLICY-3-ORA_INSTBUILD Failed to build [chars]: [chars] ([chars])
Explanation Internal error in the routing policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RIP_POLICY-3-ORA_ORABUILD Failed to build ORA[chars]: [chars] ([chars])
Explanation There was an internal error in the routing policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RIP_POLICY-3-ORA_RUN Could not apply policy operation [chars] to attribute [chars] because [chars]
Explanation Internal error in the routing policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
RIP Messages
Error Message%ROUTING-RIP-2-ERR_MEM_ALLOC Could not allocate memory for [chars]: instance [chars]
Explanation There is not enough memory available to RIP process.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-RIP-3-ERR_AUTH Failure in RIP authentication module in context [chars]: instance [chars]: error equals [chars]
Explanation Internal error encountered in RIP authentication module.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RIP-3-ERR_CFG Error during configuration in context [chars]: error equals [chars]
Explanation Internal error encountered in RIP configuration functions.
Recommended Action Please retry the configuration command that caused this error and check running configuration to make sure it is correct. If the error persists open a case with TAC.
Error Message%ROUTING-RIP-3-ERR_CLEAR Error in clear server in context [chars]: error equals [chars]
Explanation Internal error encountered in RIP clear server.
Recommended Action Please retry the command. If the error persists open a case with TAC.
Error Message%ROUTING-RIP-3-ERR_EVENT Event handling error in context [chars]: type [dec]: error equals [chars]
Explanation Internal error encountered in RIP event handling mechanisms.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RIP-3-ERR_IF Error in interface module in context [chars]: instance [chars]: error equals [chars]
Explanation Internal error encountered in RIP interface module.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RIP-3-ERR_INIT Initialization error in context [chars]: instance [chars]: error equals [chars]
Explanation There was an error during initialization of one of RIP's components.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RIP-3-ERR_ITAL ITAL error in context [chars]: VRF [chars]: Interface [chars]: IPAddress [chars]: error equals [chars]
Explanation Internal error encountered in RIP ITAL module.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RIP-3-ERR_OOM Error in handling out-of-memory condition in context [chars]: state equals [chars]: error equals [chars]
Explanation An internal error encountered in RIP's OOM module. This may affect RIP's behavior only under low memory conditions; otherwise RIP will operate normally.
Recommended Action No action is required.
Error Message%ROUTING-RIP-3-ERR_PAK_AUTH Authentication failure for RIP [chars] packet in context [chars]: instance [chars]: error equals [chars]
Explanation Authentication failure during RIP send/receive packets.
Recommended Action Please check to make sure RIP interface authentication configuration is correct. If key chains are used, please make sure atleast one active key is available for send operation. Please make sure both send and receive interfaces are configured with the same authentication mode. For text authentication mode, please make sure the active password used on the send interface key chain is also active on the receive interface key chain. For MD5 authentication mode, please make sure the active key ID and password used on the send interface key chain is also active on the receive interface key chain.
Error Message%ROUTING-RIP-3-ERR_PAK_RECV Packet receive error in context [chars]: instance [chars]: error equals [chars]
Explanation Error encountered during RIP packet receive operation.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RIP-3-ERR_POLICY Policy error in context [chars]: name [chars]: error equals [chars]
Explanation Internal error with route policies used by RIP.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RIP-3-ERR_RDB RDB error in context [chars]: VRF [chars]: TableID [unsigned int]: error equals [chars]
Explanation Error encountered in RIP's routing database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RIP-3-ERR_REDIST Redistribution error in context [chars]: protocol [chars]: instance [chars]: error equals [chars]
Explanation Internal error encountered during redistribution of other protocols into RIP.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RIP-3-ERR_RIB RIB error in context [chars]: VRF [chars]: IPAddress/PrefixLen [chars]/[unsigned int]: error equals [chars]
Explanation Error encountered by RIP during interaction with RIB.
Recommended Action These messages are expected during RIB process restart. In all other cases, please contact TAC.
Error Message%ROUTING-RIP-3-ERR_THREAD_MUTEX_LOCK Error [chars] locking [chars] in context [chars]: error equals [chars]
Explanation Internal error during locking of a RIP resource.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RIP-3-ERR_THREAD_MUTEX_UNLOCK Error unlocking [chars] in context [chars]: error equals [chars]
Explanation Internal error during unlocking of a RIP resource.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RIP-3-ERR_TOPO Route operation error in context [chars]: VRF [chars]: IPAddress/PrefixLen [chars]/[unsigned int]: error equals [chars]
Explanation Internal error encountered in RIP's topology module.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-RIP-6-INFO_OOM RIP out-of-memory event [chars]: new/current state equals [chars]: old state equals [chars]
Explanation This is an event associated with out-of-memory conditions on the router. If the new state is MINOR, no new VRF contexts or interfaces will be activated. If the new state is SEVERE, some VRF contexts and interfaces may be forcible deactivated in order to free up memory. If the new state is CRITICAL, the RIP process will