-
Cisco IOS XR System Error Message Reference Guide, Release 3.2
-
Preface
-
Cisco IOS XR System Error Messages Overview
-
Access Control List (ACL) Error Messages for Cisco IOS XR
-
Fabric (FABRIC) Error Messages for Cisco IOS XR
-
Hardware Accessibility (HA) Messages for Cisco IOS XR
-
Installation (INSTALL) Messages for Cisco IOS XR
-
Internet Protocol (IP) Messages for Cisco IOS XR
-
Layer 2 (L2) Messages for Cisco IOS XR
-
Media (MEDIA) Messages on Cisco IOS XR
-
Manageability (MGBL) Messages for Cisco IOS XR
-
Operating System (OS) Messages for Cisco IOS XR
-
Packet Infrastructure (PKT_INFRA) Messages for Cisco IOS XR
-
Platform (PLATFORM) Messages for Cisco IOS XR
-
Quality of Service (QOS) Messages for Cisco IOS XR
-
Routing (ROUTING) Messages for Cisco IOS XR
-
Security (SECURITY) Messages for Cisco IOS XR
-
Simple Network Management Protocol (SNMP) Messages for Cisco IOS XR
-
System Database (SYSDB) Messages for Cisco IOS XR
-
Feedback
Table Of Contents
Simple Network Management Protocol (SNMP) Messages
Simple Network Management Protocol (SNMP) Messages
This section contains all Simple Network Management Protocol related System Error Messages, such as BGP, MIB, CONFIG MIB, SNMP agent, and so forth. MIB location does not matter. The following facility codes are represented in this module:
ASSETMIB Messages
Error Message%SNMP-ASSETMIB-3-INIT Failed to [chars], cannot initialize: [chars]
Explanation This is given out if there are problems initialising the ciscoassetmib.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-ASSETMIB-3-NOMEM Insufficient memory to perform [chars] operation
Explanation No memory in the process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-ASSETMIB-3-SYSDBERROR Failed to perform sysdb operation [chars]. Error: [chars]:
Explanation Error from sysdb.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
BM_MIB Messages
Error Message%SNMP-BM_MIB-3-CLEANUP Failure during cleanup of [chars] in the dot3ad MIB DLL. Error: [chars]
Explanation A failure occurred during the cleanup of the DLL. This may result in the DLL not being completely cleaned up, possibly causing errors in a subsequent re-initialization of the DLL.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-BM_MIB-3-INIT Failure during intialization of [chars] in the dot3ad MIB DLL. Error: [chars]
Explanation A failure occurred during the initialization of the DLL. This resulted in the DLL not being loaded into the SNMP agent, and thus the MIB services will not be available.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
BULKFILEMIB Messages
Error Message%SNMP-BULKFILEMIB-3-INIT Failed to [chars], cannot initialize: [chars]
Explanation This is given out if there are problems initialising the bulkfilemib.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-BULKFILEMIB-3-NOMEM Insufficient memory to perform [chars] operation
Explanation No memory in the process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-BULKFILEMIB-3-NOTHREADCREATE Could not create a bulk file processing thread
Explanation There are no resources available to create a bulk file processing thread
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
CEMPMIB Messages
Error Message%SNMP-CEMPMIB-3-INIT Failed to [chars], cannot initialize: [chars]
Explanation This is given out if there are problems initialising the enhanced mempoolmib.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-CEMPMIB-3-SYSDB_ACCESS Sysdb related error: [chars]
Explanation The MIB had trouble reading from or writing to or binding/unbinding SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
CISCOBGPPAMIB Messages
Error Message%SNMP-CISCOBGPPAMIB-3-INIT_ERROR Failed to initialize [chars]
Explanation Unexpected reasons
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-CISCOBGPPAMIB-3-MEM_ERROR Failed to get memory for [chars]
Explanation Memory unavailable
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-CISCOBGPPAMIB-3-SYSDB_ERROR Failed to [chars] : [chars]
Explanation Unable to establish sysdb connection.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
CISCOPROCESSMIB Messages
Error Message%SNMP-CISCOPROCESSMIB-3-GETINFO_FAILED [chars] : Unable to get cpu/memory information from wdsysmon, err = [dec]
Explanation The MIB had trouble getting the required cpu/memory information from wdsysmon. Please check whether wdsysmon process is running.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-CISCOPROCESSMIB-3-INIT_FAILED [chars] : Unable to [chars], err = [chars]
Explanation The MIB had trouble initializing to get the required information.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-CISCOPROCESSMIB-3-NO_MEMORY [chars] : Unable to allocate memory for process name
Explanation The MIB had trouble allocating memory for process name'
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-CISCOPROCESSMIB-3-PROC_NOTFOUND [chars] : Unable to find the process with pid '[dec]'
Explanation The MIB had trouble finding the process with pid 'pid'.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
CISCOSYSTEMMIB Messages
Error Message%SNMP-CISCOSYSTEMMIB-3-CLOCK Clock operation Error: [chars]
Explanation The MIB had trouble in spawning a process.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-CISCOSYSTEMMIB-3-EVENT_ASYNC_ALLOC Failed to allocate asynchronous event: [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-CISCOSYSTEMMIB-3-SPAWN Spawn Error: [chars]
Explanation The MIB had trouble in spawning a process.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-CISCOSYSTEMMIB-3-SYSDB_ACCESS Sysdb related error: [chars]
Explanation The MIB had trouble reading from or writing to or binding/unbinding SysDB.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-CISCOSYSTEMMIB-3-TARGET_CFG_PROBLEM [chars] : Failed to [chars] target config for [chars] : [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-CISCOSYSTEMMIB-3-TIMER Timer Error: [chars]
Explanation Timer error
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-CISCOSYSTEMMIB-7-CREATE_EVM Could not create event manager for [chars] ([chars])
Explanation Attempt to create an event manager fails for some reason.
Recommended Action Use the status to determine the reason.
CONFIGMANMIB Messages
Error Message%SNMP-CONFIGMANMIB-3-REGISTER_NOTIFICATION_ERROR Could not register for notifications - no traps will be sent
Explanation Internal error
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-CONFIGMANMIB-3-SYSDB_BIND_ERR Can't bind to sysdb, aborting operation
Explanation Internal error
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-CONFIGMANMIB-3-SYSDB_GET Error [chars] getting [chars] from sysdb
Explanation Internal error
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-CONFIGMANMIB-3-SYSDB_INCONSISTENT_STATE The mib database is in an inconsistent state in [chars], line [dec]
Explanation Internal error
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-CONFIGMANMIB-3-SYSDB_SET Error [chars] setting [chars] in sysdb
Explanation Internal error
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-CONFIGMANMIB-3-TUPLE_LOCK_ERROR Could not lock tuple [chars], in [chars], line [dec] - abort operation
Explanation Internal error
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-CONFIGMANMIB-3-TUPLE_NULL_ON_SUCCESS Got NULL tuple although sysdb reported success in [chars], line [dec]
Explanation Internal error
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-CONFIGMANMIB-3-TUPLE_PACK Error packing tuple received from sysdb in [chars], line [dec]
Explanation Internal error
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-CONFIGMANMIB-3-TUPLE_UNLOCK_ERROR Could not unlock tuple [chars], in [chars], line [dec] - will time out eventually.
Explanation Internal error
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-CONFIGMANMIB-3-TUPLE_UNPACK Error unpacking tuple received from sysdb in [chars], line [dec]
Explanation Internal error
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
COPYMIB Messages
Error Message%SNMP-COPYMIB-3-ENTRYNONE Entry for id [dec] doesn't exist.
Explanation An attempt to remove an entry from a queue was made, but the entry was not found.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-COPYMIB-3-NOMEM Insufficient memory to [chars]
Explanation No memory to perform edm or bag operations.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-COPYMIB-3-NOSPAWN [chars]: Failed to start filecopy_process - cannot perform copy operation
Explanation The 'filecopy_process' could not be started, possibly due to lack of resources.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-COPYMIB-3-SYSDB_BIND Failed to open connection to sysdb when starting CISCO-CONFIG-COPY-MIB.
Explanation The CISCO-CONFIG-COPY-MIB failed to open a connection with SysDB. This MIB cannot be started at this time.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-COPYMIB-3-SYSDB_UNBIND Failed to close connection to sysdb when shutting down CISCO-CONFIG-COPY-MIB.
Explanation The CISCO-CONFIG-COPY-MIB failed to unregister from SysDB when shutting down. This may cause problems when the MIB is restarted. If the MIB does not restart properly after this message, restarting the snmpd process may alleviate the problem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-COPYMIB-3-TIMERFAIL [chars]: could not start [chars] timer for row [dec]
Explanation A copymib timer could not be started, probably due to lack of memory.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-COPYMIB-4-BADBAG Could not convert a filecopy bag into a CISCO-CONFIG-COPY-MIB row
Explanation The CISCO-CONFIG-COPY-MIB could not convert a bag retrieved from the filecopy bag server into a local MIB row.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-COPYMIB-4-BADMIB Could not convert ccCopyEntry MIB with ccCopyIndex [dec] into a filecopy bag
Explanation The CISCO-CONFIG-COPY-MIB could not convert a MIB request into a bag. The copy operation will be aborted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-COPYMIB-4-RESYNC Could not resynchronize with the filecopy bag server upon restart
Explanation The CISCO-CONFIG-COPY-MIB restarted and found the filecopy bag server running. Some bag rows created by the previous incarnation of the CISCO-CONFIG-COPY-MIB were discovered on the bag server. However, the CISCO-CONFIG-COPY-MIB could not decode some of these rows properly, and hence could not glean enough information to delete the entries on the filecopy bag server. Any requests to create new entries for the same index as these rows may result in failure. The MIB should work fine for other indices (which do not already exist on the filecopy bag server). Unfortunately, there is no way, at this time, to list the contents of the filecopy bag server, and hence you need to rely on trial-and-error to figure out which rows can be created. Please capture the error message and any related context, plus the result of a get-next walk on the CISCO-CONFIG-COPY-MIB, and send it to your customer support representative.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
CSCMIB Messages
Error Message%SNMP-CSCMIB-2-CSC_ASSERT Invalid codepath encountered - exitting.
Explanation An invalid codepath has been encountered - the process is exitting and restarting.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-CSCMIB-2-NOMEM Could not allocate memory
Explanation The MIB has failed to aquire the required amount of memory.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%SNMP-CSCMIB-2-SYSDB_BIND The MIB was unable to connect to the system database, error: [chars]
Explanation The MIB was unable to connect to the system database, so will be unable to provide the MIB data. This may be because the communications infrastructure is not yet up.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-CSCMIB-3-CSC_BAG The MIB was unable to marshall or unmarshall a set of data, error: [chars]
Explanation This may be due to invalid data being sent by the agent or request, or due to an error in the data-marshalling infrastructure. The current request cannot be completed. Check the request and try again.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-CSCMIB-3-CSC_OCTETSTRING Failed to convert an SNMP supplied OctetString to a string.
Explanation An illegal string was passed in to the MIB by the agent. The current request cannot be completed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-CSCMIB-3-CSC_SNMP The SNMP request did not specify an index.
Explanation The SNMP management station tried a set request without specifying a request index. Check the request and try again.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-CSCMIB-3-INVALID_ARG Internal error occurred: [chars]
Explanation The MIB has reached an expected state, and will not be able to service the current request.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-CSCMIB-3-SYSDB_ACCESS The MIB was unable to access the system database, error: [chars]
Explanation The MIB was unable to read to or write from the system database, so will be unable to provide some requested MIB data.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
ENTITYMIB Messages
Error Message%SNMP-ENTITYMIB-3-BADFORMAT Failed to retrieve info [chars]
Explanation Bad storage format of data in sysdb.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-ENTITYMIB-3-INIT Failed to [chars], cannot initialize: [chars]
Explanation This is given out if there are problems initialising the entitymib.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-ENTITYMIB-3-NOMEM Insufficient memory to perform [chars] operation
Explanation No memory in the process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-ENTITYMIB-3-SYSDBERROR Failed to perform sysdb operation [chars]. Error: [chars]:
Explanation Error from sysdb.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
ETHERMIB Messages
Error Message%SNMP-ETHERMIB-3-BAG An operation on a bag failed: [chars]
Explanation A problem occurred while encoding or decoding information from a bag.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-ETHERMIB-3-SYSDB_ACCESS Sysdb related error: [chars]
Explanation The MIB had trouble reading from or writing to or binding/unbinding SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
EVENTMIB Messages
Error Message%SNMP-EVENTMIB-3-BADFORMAT Failed to retrieve info [chars]
Explanation Bad storage format of data in sysdb.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-EVENTMIB-3-NOMEM Insufficient memory to perform [chars] operation
Explanation No memory in the process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-EVENTMIB-3-SYSDBERROR Failed to perform sysdb operation [chars]. Error: [chars]:
Explanation Error from sysdb.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
EXPRESSIONMIB Messages
Error Message%SNMP-EXPRESSIONMIB-4-BADTYPE Found data type [hex] in expression (should be [chars] type)
Explanation 'While evaluating an expression an operand was found with an unexpected datatype. Evaluation of this expression has been aborted.'
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-EXPRESSIONMIB-4-FAILASSERT Assertion failed: [chars]
Explanation 'An operation within the Expression MIB subsystem encountered a data value that is out of range, or of an unexpected value indicative of a logic error within the subsystem.'
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
FABHFRMIB Messages
Error Message%SNMP-FABHFRMIB-3-INIT Failed to [chars], cannot initialize: [chars]
Explanation This is given out if there are problems initialising the fabhfrmib.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-FABHFRMIB-3-NOMEM Insufficient memory to perform [chars] operation
Explanation No memory in the process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-FABHFRMIB-3-SYSDBERROR Failed to perform sysdb operation [chars]. Error: [chars]:
Explanation Error from sysdb.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
FGID_MIB Messages
Error Message%SNMP-FGID_MIB-3-MEM_ERR [chars]: FGID MIB unable to allocate [dec] bytes
Explanation The FGID MIB unable to allocate memory
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-FGID_MIB-3-SYSDB_BIND_FAILED [chars]:FGID MIB unable to bind to Sysdb name space [chars]; [chars]
Explanation The FGID MIB unable to bind to sysdb.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-FGID_MIB-3-UNKNOWN [chars]: FGID MIB fails due to an unknown error
Explanation The FGID MIB fails due to an unknown error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
FRUCONTROLMIB Messages
Error Message%SNMP-FRUCONTROLMIB-3-INIT Failed to [chars], cannot initialize: [chars]
Explanation This is given out if there are problems initialising the ciscofrucontrolmib.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-FRUCONTROLMIB-3-NOMEM Insufficient memory to perform [chars] operation
Explanation No memory in the process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-FRUCONTROLMIB-3-SYSDBERROR Failed to perform sysdb operation [chars]. Error: [chars]:
Explanation Error from sysdb.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
FTPCLIENTMIB Messages
Error Message%SNMP-FTPCLIENTMIB-3-INIT Failed to [chars], cannot initialize: [chars]
Explanation This is given out if there are problems initialising the ftpclientmib.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-FTPCLIENTMIB-3-NOMEM Insufficient memory to perform [chars] operation
Explanation No memory in the process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-FTPCLIENTMIB-3-NOTHREADCREATE Could not create a FTP request processing thread
Explanation There are no resources available to create a FTP request processing thread
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
HSRPMIB Messages
Error Message%SNMP-HSRPMIB-3-BAG Data retrieved from the standby process could not be decoded. ([chars])
Explanation The decoding of the management information retrieved from the standby process failed. This is an internal error.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%SNMP-HSRPMIB-3-DEBUG Failed to register debug control. ([chars])
Explanation During initialisation of the HSRP MIB, it was not possible to register to be notified of changes to the debugging state. The MIB will continue to function, but it will not be possible to turn on debugging for the MIB. This is an internal error.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%SNMP-HSRPMIB-3-NOMEM No memory available for processing request.
Explanation There was no memory available for processing an SNMP request in the HSRP MIB.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%SNMP-HSRPMIB-3-NOTIFICATION Failed to register for notification of state changes. ([chars])
Explanation During initialisation of the HSRP MIB, it was not possible to register to be notified of changes in active state of an HSRP group. The MIB will continue to function, but no traps will be generated for the cHsrpStateChange notification. This is an internal error.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%SNMP-HSRPMIB-3-OID Failed to construct OID in trap generation. ([dec])
Explanation An OID (object identifier) string failed to be constructed during trap generation. The trap for a cHsrpStateChange notification did not get sent. This is an internal error.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%SNMP-HSRPMIB-3-SYSDB_BIND The HSRP MIB could not connect to the HSRP process. ([chars])
Explanation The HSRP MIB was unable to create a SysDB connection to the HSRP process for the purpose of retrieving management information. This is an internal error.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%SNMP-HSRPMIB-4-FREE Failed to release allocated memory. ([chars])
Explanation A library call to free up allocated memory failed, possibly resulting in a memory leak. This is an internal error.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%SNMP-HSRPMIB-4-SYSDB_UNBIND The HSRP MIB could not disconnect from the HSRP process. ([chars])
Explanation The HSRP MIB was unable to disconnect the SysDB connection from the HSRP process, during shutdown. This is an internal error.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
IFINDEX_PROVIDER Messages
Error Message%SNMP-IFINDEX_PROVIDER-3-IFNAME_TO_INDEX Failed to [chars] for [chars]: [chars]
Explanation Failed to get the ifindex value for the given interface name
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*
Error Message%SNMP-IFINDEX_PROVIDER-3-SERVER_ERROR [chars] error during [chars]: [chars]
Explanation An error occurred while communicating with one of the servers
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*
IFMIB Messages
Error Message%SNMP-IFMIB-3-GENERAL_ERROR [chars] [chars]
Explanation Internal error
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-IFMIB-3-IFHANDLE_ERROR [chars] [dec]
Explanation Internal error
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-IFMIB-3-IFINDEX Failed to [chars] ifIndex for interface [chars]: [chars]
Explanation Failed to perform the indicated operation on the ifIndex for the given interface. This could be due to a low memory condition or an internal software error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*
Error Message%SNMP-IFMIB-3-IFSTACK_ERROR ifStackTable error: [chars] [chars]
Explanation Failed during one of the operations with the ifStackTable (initialization or runtime).
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-IFMIB-3-IM_ERROR IfMgr related error: [chars] [chars]
Explanation An error occurred while executing one of the Interface Manager APIs
Recommended Action 'If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-IFMIB-3-INIT Failed to [chars], cannot initialize: [chars]
Explanation This is given out if there are problems initialising the ifmib.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-IFMIB-3-NOMEM_ERROR Failed to [chars], due to lack of memory
Explanation The requested operation could not be performed due to a low memory condition.
Recommended Action 'Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.'
Error Message%SNMP-IFMIB-3-SYSDB_ERROR Sysdb related error: [chars] [chars]
Explanation Internal error
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
IPMIB Messages
Error Message%SNMP-IPMIB-3-BAG An operation on a bag failed: [chars]
Explanation A problem occurred while encoding or decoding information from a bag.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-IPMIB-3-SYSDB_ACCESS Operation [chars] failed, error [chars]
Explanation The MIB had trouble reading from or writing to or binding/unbinding SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
LIBSNMP Messages
Error Message%SNMP-LIBSNMP-3-NOMEM_FOR_INIT snmpd is being shut down due to lack of memory required for initialization. Try restarting snmpd after freeing some memory
Explanation Not enough memory was available for snmpd to set up its internal data structures.
Recommended Action Try stopping some running processes, or wait awhile before restarting snmpd. If the problem persists after several tries, please contact your customer support representative.
MEMPOOLMIB Messages
Error Message%SNMP-MEMPOOLMIB-3-INIT Failed to [chars], cannot initialize: [chars]
Explanation This is given out if there are problems initialising the mempoolmib.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-MEMPOOLMIB-3-SYSDB_ACCESS Sysdb related error: [chars]
Explanation The MIB had trouble reading from or writing to or binding/unbinding SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MIB Messages
Error Message%SNMP-MIB-3-BADTRANSPORT Attempt to [chars] unknown transport type: [dec]
Explanation Attempted to perform the indicated operation on an unknown transport type. This is an internal software error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-MIB-3-DEBUGDUP Duplicate debug registration for the MIB [chars]
Explanation The given MIB attempted to register MIB debugging information more than once. This is an internal software error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-MIB-3-NOINIT MIB Library not properly initialized
Explanation The MIB library was not properly initialized by the SNMP agent. This is an internal software error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-MIB-3-SYSUPTIME Failed to retrieve sysUpTime: [chars]
Explanation Failed to read the system clock, and thus determine what sysUpTime is. The result is that sysUpTime will latch at its last known value.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
PINGMIB Messages
Error Message%SNMP-PINGMIB-3-BADID Server received [chars] request with no valid id
Explanation Bad ID error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-PINGMIB-3-BAG Bag encode/decode Error : [chars]
Explanation Error bag encoding/decoding
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-PINGMIB-3-ENTRYNONE Entry for id [dec] doesn't exist
Explanation Entry for id not found
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-PINGMIB-3-EVENT_BLOCK event block call failed: [chars]
Explanation Event block call failed
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-PINGMIB-3-INIT Failed to [chars], cannot initialize: [chars]
Explanation initialization failed error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-PINGMIB-3-MSGFAIL SysDB failed to process incoming message: [chars]
Explanation Sysdb error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-PINGMIB-3-MUTEX_INIT Failed to init pthread mutex: [chars]
Explanation Failed to init pthread mutex
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-PINGMIB-3-NOMEM Insufficient memory to perform [chars] operation
Explanation Out of memory error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-PINGMIB-3-NOTHREADCREATE Could not create a PING request processing thread
Explanation There are no resources available to create a PING request processing thread
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-PINGMIB-3-PTHREAD_COND_INIT Pthread cond wait call failed: [chars]
Explanation pthread cond wait call failed
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-PINGMIB-3-SYSDB_ACCESS SysDB failed to process incoming message : [chars]
Explanation Sysdb Err
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-PINGMIB-3-SYSMGR_PROC_READY Failed to notify sysmgr the completion of initialization: [chars]
Explanation Failed to notify sysmgr the completion of initialization
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-PINGMIB-3-TIMER Failed to create [chars] timer
Explanation Timer error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-PINGMIB-3-TIMERNOMEM Insufficient memory to create timer for entry [dec]
Explanation Insufficient memory to create timer for entry error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-PINGMIB-3-TIMERNONE Failed to find timer for entry id [dec]
Explanation Failed to find timer for entry
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-PINGMIB-3-TRAPOID Failed to create trap OID for [chars]
Explanation Failed to create trap OID error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-PINGMIB-3-UNKNOWNMSG Received unknown event type: [dec]
Explanation Received unknown event type error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
QOSMIB Messages
Error Message%SNMP-QOSMIB-3-ALL_OTHER Unable to [chars]. Error: [chars]
Explanation All other error message from dependent modules.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-QOSMIB-3-BADFORMAT Failed to retrieve info [chars]
Explanation Bad storage format of data in sysdb.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-QOSMIB-3-INIT_FAILED [chars] : Unable to [chars], err = [chars]
Explanation The MIB had trouble initializing to get the required information.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-QOSMIB-3-NO_MEMORY Insufficient Memory to perform [chars] operation
Explanation The MIB had trouble allocating memory.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-QOSMIB-3-SYSDB_ERROR Failed to perform sysdb operation [chars]. Error: [chars]
Explanation The MIB had trouble allocating memory.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
SENSORMIB Messages
Error Message%SNMP-SENSORMIB-3-INIT Failed to [chars], cannot initialize: [chars]
Explanation This is given out if there are problems initialising the ciscosensormib.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SENSORMIB-3-NOMEM Insufficient memory to perform [chars] operation
Explanation No memory in the process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SENSORMIB-3-SYSDBERROR Failed to perform sysdb operation [chars]. Error: [chars]:
Explanation Error from sysdb.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
SNMP Messages
Error Message%SNMP-SNMP-1-TIMER [chars]: [chars]
Explanation Timer problem; internal software error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-BADMSG Unexpected message type: [dec]
Explanation While receiving incoming messages from the event manager, an unknown message type was received. This is likely due to an internal software error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-BADSUBTREE Invalid MIB view subtree: [chars]
Explanation A malformed MIB view subtree was found in the configuration. This configuration entry will be ignored.
Recommended Action Examine your configuration, ensuring that all MIB view configurations are sane. Copy the error message exactly as it appears on the console or in the system log. Issue the config command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the config output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-BADTRANSPORT Invalid transport type [dec]
Explanation An unknown transport protocol type was found. This is an internal software error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-CONFIGFAIL Failed to [chars] [chars]: [chars]
Explanation Failed to perform the indicated configuration operation. This could be due to a low memory condition, an unsane configuration, or an internal software error.
Recommended Action Examine the configuration and ensure that it is sane. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *SH_CMD config*
Error Message%SNMP-SNMP-3-DATASIZE Data size exceeded for [chars]. Length of data is [dec](max length is [dec])
Explanation The maximum size of the data has been exceeded. This could be due to user configuration or internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-DEBUGDUP Duplicate debug registration for the MIB [chars]
Explanation The given MIB attempted to register for MIB debug handling more than once. This is an internal software error. It may not have a detrimental effect on the behavior of the SNMP agent.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-DEBUGFAIL Failed debug registration for the MIB [chars]
Explanation Failed to initialize support for the command 'debug snmp mib xxx', where 'xxx' is the MIB indicated in the error message. This could be due to a low memory condition or an internal software error. The result is that this command cannot be used.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*
Error Message%SNMP-SNMP-3-DEBUGINIT Failed debug registration for SNMP
Explanation Failed to initialize support for the command 'debug snmp xxx', where xxx is one of the areas of debug interest within SNMP. This could be due to a low memory condition or an internal software error. The result is that this command cannot be used.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*
Error Message%SNMP-SNMP-3-DEBUGNOMEM Failed to initialize or deinitialize debugging of MIB [chars] due to lack of memory
Explanation The requested operation could not be performed due to a low memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%SNMP-SNMP-3-EVENTERR Received error from event_wait: [chars]
Explanation SNMP receives messages from an event manager. While trying to retrieve a message, an error occured, preventing successful receipt of the message.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-FAILSYSDBOPER The requested SysDB '[chars]' operation for '[chars]' tuple failed with SysDB error : [chars].
Explanation The SysDB Set/Delete operation failed due to some internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-HARIKARI SNMP top-level Trap routine exited
Explanation The trap processing routine unexpectedly terminated. This is an internal software error.
Recommended Action If you are not interested in generating traps/notifications, this can safely be ignored. Otherwise, kill and restart the snmpd process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-HOSTCFGFAILED Received a good snmp host tuple: [chars], but recvd an internal error during configuration.
Explanation Received a good tuple for the snmp-server host CLI command, but could not configure it. This is likely due to lack of memory, which may be a transient condition, or may be due to SNMP supporting too many MIBS with large amounts of data. Try this command again after a few minutes. If it continues to fail, you may wish to undo some SNMP configurations and then retry the command.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-INIT Failed to [chars], cannot initialize: [chars]
Explanation The requested operation could not be performed, due to the given reason. This could be due to a low memory condition, or an internal software error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*
Error Message%SNMP-SNMP-3-INTERNAL Unexpected internal failure : [chars], [chars]
Explanation Detected unexpected condition and failed to recover from it
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-MIBCFGDIR Cannot discover MIB configs: [chars]
Explanation The MIB configuration files should be located in the directory '/ios/mib'. This directory could not be read, for the given reason.
Recommended Action Ensure that the '/ios/mib' directory exists and contains one or more files with a '.mib' suffix. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-MIBCFGERR [chars]: line [dec], [chars]
Explanation A syntax error was encountered while parsing the given MIB configuration file. The MIB referred to by this configuration file will not be loaded.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Also provide the contents of the given configuration file.
Error Message%SNMP-SNMP-3-MIBCFGMISSING MIB config file [chars] missing necessary entries
Explanation One or more required entries are missing from the given MIB configuration file. The MIB referred to by this configuration file will not be loaded.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Also provide the contents of the given configuration file.
Error Message%SNMP-SNMP-3-MIBCFGREAD Failed to read MIB config [chars]: [chars]
Explanation Failed to read the given MIB configuration file. This could be due to a low memory condition.
Recommended Action Ensure that the specified configuration file does exist on the system. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%SNMP-SNMP-3-MIBINSTALL [chars]
Explanation An error was encountered during installation of a new MIB or deletion of an old MIB. These messages are printed when MIB installation/deletion failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-MIBLOAD Failed to load [chars]: [chars]
Explanation Failed to load the given MIB, for the given reason. This could be due to a low memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%SNMP-SNMP-3-MIBMAP Failed to map [chars] to an address: [chars]
Explanation An attempt to map a MIB DLL symbolic name to an address failed. This MIB will be unloaded. This could be due to a corrupted MIB configuration file, a corrupted DLL, or a MIB configuration file that is out-of-sync with its corresponding MIB DLL.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Also provide a copy of the MIB DLL and its associated MIB configuration file.
Error Message%SNMP-SNMP-3-MIBOID MIB [chars] failed to provide OID list
Explanation All MIBs, after they are loaded, are required to inform the SNMP agent which OIDs they support. The given MIB failed to do this. It will be unloaded. This is an internal software error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-NOENABLETHREAD Could not create a thread to set all individual trap tuples in SysDB.
Explanation There are no resources available to create a thread.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-NOMEM Failed to [chars], due to lack of memory
Explanation The requested operation could not be performed due to a low memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%SNMP-SNMP-3-NOTIFOID_FAILED Failed to add sysObjectID to notification view for trapstring: [chars]
Explanation Every trapstring supported by the 'snmp host' command corresponds to one or more notification OIDs. Each of these notifications will have zero or more varbinds that are carried as payload - each MIB tells snmpd about these varbinds so that a 'notification view' can be built for them. An extra varbind - sysObjectID - is required to be sent with all v2c notifications. This message indicates that an attempt to register this varbind failed. Sending v2c notifications for the trapstring specified in the error message may fail. You can workaround this by not specifying any trapstring in the 'snmp host' configuration - this will enable all notifications for that destination.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*
Error Message%SNMP-SNMP-3-NOTIFYINFO Failed to retrieve notification info: [chars]
Explanation Failed to retrieve and process a MIB notification. This is an internal software error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-NOTIFYNONE Cannot find handler for notification [chars]
Explanation We received a MIB notification but cannot locate the module responsible for interpreting it. This is an internal software error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-PATHDECODE Failed to decode path [chars]
Explanation Failed to extract a transport address from the given encoded pathname. This is an internal software error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-PATHENCODE Failed to encode path for due to lack of memory
Explanation Due to a low memory condition, the transport address for an outgoing PDU could not be encoded into an internal pathname. The outgoing PDU will be discarded.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%SNMP-SNMP-3-RESTART An system manager error occured restarting snmpd. please restart snmpd using 'process restart snmpd' command.
Explanation This is a internal error in system manager restarting snmpd.
Recommended Action you can safely restart snmpd by entering 'process restart snmpd' at the enable mode of the CLI. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-STATSGET Unable to [chars]
Explanation When a show snmp CLI is executed, SNMP agent displays this message when it is not able to retrieve the information. This is likely due to an internal software error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-SYSDBBIND Failed to bind to SysDB for MIB notifications: [chars]
Explanation SNMP binds to SysDB to receive notifications on the MIB's behalf. MIBs typically use these notifications as triggers to send out SNMP notifications (e.g. Traps). If SNMP cannot bind to SysDB, these SysDB notifications will not be received, and thus some SNMP notifications may never be generated.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-SYSDBFREE Failed to free resources after processing SysDB tuples when [chars]
Explanation An attempt to free resources assoicated with SysDB operations (e.g. memory malloced for tuples) failed. The result may be that whatever action was being performed may fail.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-SYSDBMSG SysDB failed to process message: [chars]
Explanation An incoming message from SysDB was not processed successfully. The result being that whatever request it was, will not be performed by the SNMP agent.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-SYSDBREAD Failed to read from SysDB when processing [chars]
Explanation An attempt to read from SysDB failed, the result being that whatever action was being performed cannot be completed by the SNMP agent.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-TARGETNONE Cannot find notification target [chars]
Explanation A configuration command refers to an SNMP target that has not yet been configured.
Recommended Action You must configure an SNMP target before you can refer to it. Examine your configuration. Ensure that the given target has been configured. If it has not, configure it. Copy the error message exactly as it appears on the console or in the system log. Issue the config command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the config output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-TRANSPORTIO Failed to [chars] transport [chars]: [chars]
Explanation Failed to communicate with the SNMP transport process. This could be due to a low memory condition, or the fact that there is no SNMP transport process running.
Recommended Action Check the running processes to ensure that an appropriate SNMP transport process is running. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%SNMP-SNMP-3-TRAPADDRESS [chars]:[chars]
Explanation Could not get the trap source address for the outgoing trap packets. This is likely an internal software error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-TRAPSEND Failed to send trap to [chars]
Explanation A trap destined for the given address could not be sent. This could be due to a low memory condition. It also might be due to the fact that there is no SNMP transport process running for that transport protocol (e.g. udp_snmpd for SNMP over UDP).
Recommended Action Check the running processes to ensure that an appropriate SNMP transport process is running. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%SNMP-SNMP-3-TUPLEBADHOST Received bad snmp host tuple: [chars]
Explanation Received a tuple for the snmp-server host CLI command, but could not parse it. This is an internal software error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-TUPLEBADID Received tuple request with no valid keys
Explanation Received a SysDB read request, yet the input information was malformed. This is an internal software error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-TUPLENAME Cannot parse tuple name [chars]
Explanation This is an internal software error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-TUPLETYPE Tuple [chars]%s is type [unsigned int] (should be [unsigned int])
Explanation The retrieved datatype for the given SysDB tuple does not match the expected datatype. This is an internal software error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-TUPLEUNKNOWN Unexpected tuple [chars]%s
Explanation Received a SysDB tuple that we know nothing about. This is an internal software error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-3-TUPLEUNPACK Failed to unpack tuple [chars]%s
Explanation Failed to decode/unpack the retrieved SysDB tuple value. This is an internal software error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-4-BAGREG Failed to register bags with SysDB for providing SNMP statistics and MIB information: [chars]
Explanation Failed to register the bags with SysDB. The access to SNMP statistics and MIB items in /oper/snmp/info through 'sysdbcon' might not be available. This is likely due to an internal software error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-4-CONFIGOPEN Failed to open snmp agent configuration file
Explanation Failed to open snmp agent configuration file, /disk0/config/snmp/snmpd.cnf
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-4-EDMREG Failed to register as EDM for providing SNMP statistics and MIB information: [chars]
Explanation Failed to register as EDM. The access to SNMP statistics and MIB information through 'show snmp' CLI command will not be available. This is likely due to an internal software error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-4-ENABLEFAILED Unable to parse tuple [chars] when trying to enable or disable a trap
Explanation The SysDB tuple was not properly formatted, and hence could not be parsed. This will not degrade system performance, but the user will be unable to enable or disable some traps.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-4-ENABLENOMEM Insufficient memory to enable (or disable) [chars] traps
Explanation Due to a low memory condition we could not enable (or disable) the specified traps. Until available memory is increased and the SNMP process is restarted, these notifications will not be generated by the agent.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%SNMP-SNMP-4-ENABLENOTSUPPORTED Unrecognized trap type ([chars]). MIB is not loaded
Explanation The snmp-server enable traps command allowed the user to set the specified traptype, but no callback function was registered to handle the command. This should have no detrimental effect on the system, but the user will not be able to enable/disable the specified trap.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-4-ENABLETRAPSTWICE [chars] MIB attempt to register same handler for the snmp enable traps [chars] command twice: handler: [hex]
Explanation The given MIB attempted to register a second handler for the same traptype in the 'snmp enable traps ' command. This should have no detrimental effect on the behavior of the system.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-4-EXCEEDEDSIZE The maximum allowed size for enable trap tuple exceeded for [chars] trapstring
Explanation While creating an enable trap tuple we exceeded the limit of maximum allowed size. The snmp enable trap command for this trapstring will not be NVGENed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-4-INSTALL unknown notification received from install manager:[dec]
Explanation snmpd received a unidentified notification from the install manager regarding an installation package.
Recommended Action you can ignore this message if the installed package is not related to snmp agent or MIBS. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-4-NOENCODE Failed to encode a bag due to [chars]
Explanation Failed to encode a bag. The access to SNMP statistics and MIB information through 'show snmp' CLI command might not be available. This is likely due to an internal software error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-4-NOTIFYNOMEM Insufficient memory to register for [chars] notifications
Explanation Due to a low memory condition we could not register to receive the specified MIB notifications. Until available memory is increased and the SNMP process is restarted, these notifications will not be generated by the agent.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%SNMP-SNMP-4-NOTIFYREG Failed to register for notifications on [chars]: [chars]
Explanation Failed to register for receipt of the given notifications. This could be due to a low memory condition or an internal software error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*
Error Message%SNMP-SNMP-4-NOTIFYTWICE [chars] MIB attempt to register for [chars] notifications again: existing handlers: [hex] [hex]
Explanation The given MIB attempted to register more than once for the given MIB notifications. This should have no detrimental effect on the behavior of the system.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-4-RESPONSE Failed to send response to [chars]
Explanation A response destined for the given address could not be sent. This could be due to a low memory condition. It also might be due to the fact that there is no SNMP transport process running for that transport protocol (e.g. udp_snmpd for SNMP over UDP).
Recommended Action Check the running processes to ensure that an appropriate SNMP transport process is running. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%SNMP-SNMP-4-TARGETINUSE Notification target [chars] is in use
Explanation An attempt was made to unconfigure an SNMP target, however that target is still in use by one or more other SNMP configuration commands.
Recommended Action You must remove all other configuration commands that refer to this target before you can remove this target configuration. Copy the error message exactly as it appears on the console or in the system log. Issue the config command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the config output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-4-TRAPEMPTY Found empty trap, destined for [chars]
Explanation A trap destined for the given address was empty. This is an internal software error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-4-TRAPQNOMEM Insufficient memory to enqueue trap destined for [chars]
Explanation A trap could not be sent to the given destination due to a low memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%SNMP-SNMP-4-VERIFYREG Failed to register for verifications on [chars]: [chars]
Explanation Failed to register for receiving and processing config and/or debug CLI commands. This could be due to a low memory condition or an internal software error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*
Error Message%SNMP-SNMP-4-VIEWFAIL Could not create view: [chars]
Explanation Could not create an SNMP view using the 'snmp-server view' CLI command. Possible causes could be poorly formatted viewnames or oid subtrees.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SNMP-4-VIEWOID_NOT_FOUND The command [chars] could not be applied at this time because the oid [chars] does not belong to a known MIB module.
Explanation The snmpd process attempted to load the view OID, but the OID did not correspond to any known MIB module.
Recommended Action It could be that either - 1. the OID is of the format 'foobar.1', but the MIB module containing the OID 'foobar' is not yet loaded on the router. If this is the case, when the MIB is loaded, this command will be automatically applied - there is no need to re-enter it. 2. The MIB module containing the OID 'foobar' is indeed loaded, but the MIB did not load a translation from 'foobar' to '1.3.6.1.x.y.z' (i.e. there is no translation from the oid-name to the dotted decimal representation for that name). In this case, you can enter the dotted decimal version instead of the name, i.e. 'snmp-server view 1.3.6.1.x.y.z included' - note that using the dotted decimal version of the name will ALWAYS succeed without a warning message - it is upto the user to make sure the OID entered is valid. 3. The OID 'foobar.1' contains a typo - please re-enter the command with the correct OID and it should succeed. If the above steps result in repeated warning messages or failure, please contact your customer support representative wit the error message.
Error Message%SNMP-SNMP-7-TUPLEVALUE Failed to retrieve tuple [chars]%s: [chars]
Explanation Failed to retrieve the given SysDB tuple for the given reason. This may or may not have a detrimental effect on the behavior of the SNMP agent (depends on which tuple it is).
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
SONETMIB Messages
Error Message%SNMP-SONETMIB-3-BAG An operation on a bag failed: [chars]
Explanation A problem occurred while encoding or decoding information from a bag.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SONETMIB-3-NOMEM_ERROR Failed to [chars], due to lack of memory
Explanation The requested operation could not be performed due to a low memory condition.
Recommended Action 'Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.'
Error Message%SNMP-SONETMIB-3-SYSDB_ACCESS Sysdb related error: [chars]
Explanation The MIB had trouble reading from or writing to or binding/unbinding SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
SONETMIBAPI Messages
Error Message%SNMP-SONETMIBAPI-2-THREAD_CREATE pthread_create([chars]) failed
Explanation Sonet MIB API had trouble in creating thread.
Recommended Action File a DDTS If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SONETMIBAPI-3-BAG An operation on a bag failed: [chars]
Explanation A problem occurred while encoding or decoding information from a bag.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SONETMIBAPI-3-EVM_CREATE_ERR Event manager create failed : [chars]
Explanation An internal operation failed. The system will attempt to recover.
Recommended Action Copy the message exactly as it appears, and report it to your technical support representative.
Error Message%SNMP-SONETMIBAPI-3-NOMEM_ERROR Failed [chars], due to lack of memory
Explanation The requested operation could not be performed due to a low memory condition.
Recommended Action 'Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.'
Error Message%SNMP-SONETMIBAPI-3-SYSDB_ACCESS Sysdb related error: [chars]
Explanation SonetMIB API had trouble registering/deregistering EDM or binding/unbinding SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
SYSLOGMIB Messages
Error Message%SNMP-SYSLOGMIB-3-NOMEM Insufficient memory to perform [chars] operation
Explanation No memory in the process.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%SNMP-SYSLOGMIB-3-PARSEERROR Failed to parse [chars]
Explanation This is given out if there are problems parsing the encoded tuple from syslogd/sysdb.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-SYSLOGMIB-3-SYSDBERROR Failed to [chars]. Error: [chars]:
Explanation The syslog mib reads the sysdb tuples and gets information about the syslog mib objects. If due to some reason the sysdb error occurs this message is printed out.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
TCP Messages
Error Message%SNMP-TCP-3-TCP_MIB_DEBUG_INVALID_CMD TCP MIB: Invalid command
Explanation The TCP component received an invalid command from the MIB DLL, so the request could not be processed
Recommended Action The MIB DLL is issuing a command that's not recognised by the TCP component. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-TCP-7-TCP_MIB_DEBUG_END_OF_TABLE TCP MIB: End of Table
Explanation There are no more entries in the table.
Recommended Action *NONE*
Error Message%SNMP-TCP-7-TCP_MIB_DEBUG_NO_ERROR TCP MIB: No Error
Explanation There was no error reported by the TCP component when dealing with an SNMP request
Recommended Action *NONE*
Error Message%SNMP-TCP-7-TCP_MIB_DEBUG_NOT_FOUND TCP MIB: Entry not found
Explanation The tcpConnEntryTable entry specified does not exist
Recommended Action Check the entries recorded under tcpConnEntryTable
Error Message%SNMP-TCP-7-TCP_MIB_DEBUG_OTHER TCP MIB: TCP Error
Explanation An error occured in the TCP process.
Recommended Action *RECUR*
Error Message%SNMP-TCP-7-TCP_MIB_DEBUG_UNKNOWN TCP MIB: Unknown error
Explanation An unknown error was returned from the TCP process
Recommended Action *RECUR*
UDP_MIB Messages
Error Message%SNMP-UDP_MIB-3-RPC RPC Error: func:[chars] op:[chars] err:[chars]
Explanation An RPC error occurred
Recommended Action *SUPPORT*
UDPSNMP Messages
Error Message%SNMP-UDPSNMP-3-AGENTIO Failed to [chars] agent [chars]: [chars]
Explanation Communications with the SNMP agent failed. This may be due to a low memory condition or an internal software error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*
Error Message%SNMP-UDPSNMP-3-DEBUGCLEANUP Failed to cleanup debug registration for udp_snmpd
Explanation Failed to cleanup support for the command 'debug udp_snmpd xxx', where xxx is one of the areas of debug interest within udp_snmpd. This could be due to a low memory condition or an internal software error. The result is that this command cannot be used.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*
Error Message%SNMP-UDPSNMP-3-DEBUGINIT Failed initialize debug registration for udp_snmpd
Explanation Failed to initialize support for the command 'debug udp_snmpd xxx', where xxx is one of the areas of debug interest within udp_snmpd. This could be due to a low memory condition or an internal software error. The result is that this command cannot be used.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*
Error Message%SNMP-UDPSNMP-3-HARIKARI UDP SNMP top-level routine exited
Explanation The main subroutine unexpectedly terminated. This is an internal software error.
Recommended Action Attempt to restart the udp_snmpd process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-UDPSNMP-3-INIT Failed to [chars], cannot initialize: [chars]
Explanation Initialization failed. This could be due to a low memory condition or an internal software error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*
Error Message%SNMP-UDPSNMP-3-NOMEM Failed to [chars], due to lack of memory
Explanation The requested operation could not be performed due to a low memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%SNMP-UDPSNMP-3-PARSEERROR The host configuration in sysdb([chars]) could not be read.
Explanation The sysdb configuration for trap host does not have valid format This is an internal software error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-UDPSNMP-3-PATHDECODE Failed to decode path [chars]
Explanation A transport address could not be extracted from an internal pathname. This is an internal software error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-UDPSNMP-3-PATHENCODE Failed to encode path due to lack of memory
Explanation Due to a low memory condition, a transport address could not be encoded into an internal pathname.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%SNMP-UDPSNMP-3-RECVFROM recvfrom failed, [chars]: [chars]
Explanation An error condition arose while reading an incoming packet. This could be due to a low memory condition or an internal software error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*
Error Message%SNMP-UDPSNMP-3-SOCKET Failed to [chars] socket, [chars]: [chars]
Explanation Failed to perform the indicated operation on the socket. This could be due to a low memory condition or an internal software error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*
Error Message%SNMP-UDPSNMP-3-SYSDBBIND Failed to bind to SysDB for trap destination notifications: [chars]
Explanation udp_snmpd binds to SysDB to receive notifications on the trap destinations udp_snmpd typically use these notifications to add trap destination to the trap Q. If udp_snmpd cannot bind to SysDB, these SysDB notifications will not be received, and thus some trap desination will not be added and traps will not be sent to those destinations.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-UDPSNMP-3-SYSDBERROR Failed to [chars] due to sysdb error:[chars]
Explanation udp_snmpd reads the snmp trap Q length and trap timeout from the sysdb. If udp_snmpd is not able to read it then this error is printed. This is an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%SNMP-UDPSNMP-3-TRUNC Inbound message truncated
Explanation The inbound PDU was truncated before it was received by udp_snmpd. This is due to a low memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%SNMP-UDPSNMP-4-NOTIFYREG Failed to register for notifications on [chars]: [chars]
Explanation Failed to register for receipt of the given notifications. This could be due to a low memory condition or an internal software error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*
Error Message%SNMP-UDPSNMP-4-TOOBIG Outgoing PDU is [unsigned int] bytes, max is [unsigned int]
Explanation The outgoing PDU is greater than the configured maximum PDU size. The PDU will be dropped. This should never occur, as the SNMP agent should determine that the PDU is too big before sending it to the udpsnmpd process. This is an internal software error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
UTIL Messages
Error Message%SNMP-UTIL-3-NOINIT SNMP Utilities Library not properly initialized
Explanation The SNMP Utilities library was not properly initialized by the SNMP agent. This is an internal software error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
VLANIFMIB Messages
Error Message%SNMP-VLANIFMIB-3-BAG Bag encode/decode Error : [chars]
Explanation Error bag encoding/decoding
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-VLANIFMIB-3-GEN Failed to [chars]
Explanation Initialisation error
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-VLANIFMIB-3-MEMORY Failed to [chars]
Explanation Memory allocation/deallocation error
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-VLANIFMIB-3-MIBLIB Failed to [chars]
Explanation MIB Libraries error
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%SNMP-VLANIFMIB-3-SYSDB_ACCESS SysDB failed to [chars]
Explanation Sysdb error
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
