-
Cisco IOS XR System Error Message Reference Guide, Release 3.2
-
Preface
-
Cisco IOS XR System Error Messages Overview
-
Access Control List (ACL) Error Messages for Cisco IOS XR
-
Fabric (FABRIC) Error Messages for Cisco IOS XR
-
Hardware Accessibility (HA) Messages for Cisco IOS XR
-
Installation (INSTALL) Messages for Cisco IOS XR
-
Internet Protocol (IP) Messages for Cisco IOS XR
-
Layer 2 (L2) Messages for Cisco IOS XR
-
Media (MEDIA) Messages on Cisco IOS XR
-
Manageability (MGBL) Messages for Cisco IOS XR
-
Operating System (OS) Messages for Cisco IOS XR
-
Packet Infrastructure (PKT_INFRA) Messages for Cisco IOS XR
-
Platform (PLATFORM) Messages for Cisco IOS XR
-
Quality of Service (QOS) Messages for Cisco IOS XR
-
Routing (ROUTING) Messages for Cisco IOS XR
-
Security (SECURITY) Messages for Cisco IOS XR
-
Simple Network Management Protocol (SNMP) Messages for Cisco IOS XR
-
System Database (SYSDB) Messages for Cisco IOS XR
-
Feedback
Table Of Contents
IPV4_MCAST_NETIO_DEBUG Messages
POLICY_REPOSITORY_EDM Messages
POLICY_REPOSITORY_REG Messages
Routing Messages
This section contains all routing related System Error Messages, such as MPLS, OSPF, BGP, Multicast, MRIB, RIB, and so forth. The following facility codes are represented in this module:
•
IPV4_MCAST_NETIO_DEBUG Messages
•
•
AUTORP_CRP Messages
Error Message%ROUTING-AUTORP_CRP-3-BAG_RELATED_ERROR Bag related error: [chars]
Explanation The Candidate RP had trouble wth Bags.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-EVENT_CONN_MGR_ERROR Event connection manager error : [chars], [chars]
Explanation Failed to open connection to Connection Manager.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-EVENT_MGR_CREATE_FAILED Failed to create an event manager
Explanation A problem occurred when a call to event_manager_create() was made.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-GEN_ERROR Error : [chars] failed - [chars]
Explanation General Error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-IM_RELATED_ERROR A call to [chars] returned [chars]
Explanation A problem occurred when a call to IM was made.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-INIT_FAILED Initialization failed : [chars]
Explanation autorp_candidate_rp failed to initialize successfully.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-IPARM_RELATED_FAILURE A call to [chars] returned [chars]
Explanation A problem occurred when a call to one of the IPARM APIs was made.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-MALLOC_FAILED malloc() failed : failed to allocate memory to receive messages
Explanation A call to malloc() failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-SOCKET_ERROR Socket Error : [chars] : [chars]
Explanation Socket Error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-SYSDB_ACCESS_ERROR Sysdb related error: [chars], [chars]
Explanation The Candidate RP had trouble accessing SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-SYSDB_REGISTRATION_FAILED Sysdb registration error: [chars]
Explanation The Candidate RP had trouble registering as a notifier with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-TIMER_ERROR Timer Error : [chars]
Explanation Timer Error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-TUPLE_ERROR Tuple operation error : [chars]
Explanation Tuple operation failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
AUTORP_MAP Messages
Error Message%ROUTING-AUTORP_MAP-3-BAG_RELATED_ERROR Bag related error: [chars]
Explanation The Mapping Agent had trouble wth Bags.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-DEBUG_ERROR Debug error : [chars]
Explanation Debug Error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-EVENT_CONN_MGR_ERROR Event connection manager error: [chars], [chars]
Explanation Failed to open connection to Connection Manager.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-EVENT_MGR_CREATE_FAILED A call to event_manager_create() failed
Explanation A problem occurred while calling the event_manager_create() API.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-IM_RELATED_ERROR The function [chars] returned error : [chars]
Explanation Failed some IM related operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-INIT_FAILED Initialization failed : [chars]
Explanation autorp_mapping_agent failed to initialize successfully.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-IPARM_RELATED_FAILURE A call to [chars] returned [chars]
Explanation A problem occurred when a call to one of the IPARM APIs was made.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-MALLOC_FAILED malloc() failed : failed to allocate memory to receive messages
Explanation A call to malloc() failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-OOR_LIMIT Cache maximum reached: [dec], new group range not added
Explanation OOR Error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-RTREE_ERROR RTree error : [chars]
Explanation Timer Error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-SOCKET_ERROR Socket Error : [chars] : [chars]
Explanation Socket Error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-SYSDB_ACCESS_ERROR Sysdb related error: [chars], [chars]
Explanation The Mapping Agent had trouble accessing SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-SYSDB_REGISTRATION_FAILED Sysdb registration error: [chars]
Explanation The Mapping Agent had trouble registering as a notifier/edm with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-TIMER_ERROR Timer Error : [chars]
Explanation Timer Error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-TUPLE_ERROR Tuple operation error : [chars]
Explanation Tuple operation failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
BGP Messages
Error Message%ROUTING-BGP-2-ADDROUTE Failed to add net [chars] to the BGP table
Explanation An error occurred whilst trying to insert a net to the BGP table database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-2-BRIB_API_SYNC bRIB API detected loss of sync: invalid [chars] [hex] at [hex]
Explanation The data stream between the bRIB and a speaker was corrupted and the receiving process could not interpret the received message.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-2-DEADLOCK Deadlock detected (thread [unsigned int]): holding: [chars]
Explanation BGP detected a lock being held when all locks should have been released.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-2-EVENTLOOP Error in event loop for [chars] thread: [chars]
Explanation An error occurred in the event loop.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-2-FATAL_WRAPPER Fatal error: A call to [chars] failed unexpectedly: [chars]
Explanation A function call failed unexpectedly - this is probably a system problem
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-2-NOMEM Failed to allocate memory for [chars]
Explanation The requested operation could not be accomplished because of a low memory condition. BGP may not operate correctly until the process is restarted.
Recommended Action Reduce other system activity to ease memory demands, then restart the process. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-BGP-3-AF_LIB_FILE_ERROR Failed to read Address Family data file: [chars] [chars]
Explanation 'File/Directory open operation failed, or the data in the file was corrupt'
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-AF_LIB_FILE_WRONG_INFO Failed to read Address Family data file [chars]: [chars] on line [unsigned int]
Explanation 'The data in the Address Family data file was corrupt'
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ALREADY_DONE Cannot [chars]%s: already done
Explanation An operation could not be performed because it had already been completed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ATTRKEY_BAD Failed to [chars] RIB due to an invalid attribute key number ([hex])
Explanation There is a problem with the attribute key generation routine.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ATTRKEY_CHKPT Failed to checkpoint attribute key
Explanation The chkpt library failed to checkpoint the attribute key number. Normal operation of BGP (standalone) or bRIB (distributed) is not impacted unless the process is restarted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ATTRKEY_OVERFLOW Failed to generate a new attribute key for the incoming UPDATE
Explanation This is an extremely rare case where the attribute key overflow protection mechanism fails.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-BAD_REFCNT Bad reference count value ([unsigned int]) for [chars] ([pointer])
Explanation 'This indicates a internal data structure inconsistency'
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-BPM_INIT Initialization failed ([chars]%s)
Explanation An error occurred while initializing the BGP process manager. The process will be restarted.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-BPM_PROCESS_START Failed to start [chars] process (ID: [unsigned int]): [chars]
Explanation The BPM failed to start the process in the error message. As a result, the process will not be running.
Recommended Action Check that the process is not already running using the 'show process bgp location all' or 'show process brib location all' command as appropriate. If the process is not running, attempt to start it using the 'process restart' command. If other error messages are seen along with this one, or when attempting to manually start the process, please consult the documentation for those errors and attempt to rectify them. If problems persist, copy this error message and any others exactly as they appear on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-BPM_PROCESS_STOP Failed to stop [chars] process (ID: [unsigned int]): [chars]
Explanation An error occurred when trying to stop the process specified in the error message. As a result, the process may still be running, which could adversely affect the operation of other processes.
Recommended Action Check whether the process is still running using the 'show process bgp location all' or 'show process brib location all' command as appropriate. If the process is running, kill it using the 'process kill' command. If problems persist, copy this error message and any subsequent ones exactly as they appear on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-BPM_SWITCH_MODE Failed to switch to [chars] mode: [chars] ([chars])
Explanation An error occurred when switching between standalone and distributed mode.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-BRIB_INIT Initialization failed ([chars]%s)
Explanation An error occurred while initializing the BGP RIB. If this occurs during process startup, the process will be restarted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-BUF_TOO_SHORT A string buffer was too short during a string print operation (string [chars] truncated)
Explanation Whilst trying to format a string, the buffer passed in was too short and the string was truncated.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-CONFIG_DEL Apply delete of [chars] failed with warning: [chars], no further action necessary.
Explanation A speaker or the bRIB failed to process the removal of some configuration.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-CONFIG_FALLOVER Apply for fast-external-fallover failed: [chars]
Explanation A speaker failed to process a configuration change for 'fast-external-fallover'
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-CONFIG_SET Apply for [chars] failed with error: [chars], system may now be in an inconsistent state.
Explanation A speaker or the bRIB failed to process a configuration change.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-DEBUG_CONFIG Failed to apply debug configuration: [chars]
Explanation An error occurred whilst applying the debug configuration
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-DELPATH Attempted to delete path from empty net [chars]
Explanation An attempt was made to delete a path from a net with a path count of 0
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-DLL_ERROR Failed to [chars] [chars] DLL: [chars]
Explanation An error occurred whilst trying to open or initialize an address family DLL
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-EDM_INIT_FAILED EDM server initialization failed: [chars]: [chars]
Explanation Initialization of the EDM server failed. The process will be restarted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-IFACE_LOOKUP Interface lookup for [chars] Failed: [chars]
Explanation Interface manager failed to lookup nexthop interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-IM_DMZLINK_BW Failed to register for DMZ link bandwidth change for neighbor [chars]: [chars]
Explanation BGP failed to register with interface manager for DMZ link bandwidth change notifiction for a given neighbor
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-INIT_GET_VALUE Failed to obtain [chars] during initialization: [chars]
Explanation An error occurred when retrieving a required value during initialization. As a result the BGP process can not initialize.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-INSUFMEM Failed to allocate memory for [chars]
Explanation The requested operation could not be accomplished because of a low memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-BGP-3-IO_INIT Initialization failed: [chars] [chars] ([chars])
Explanation An error occurred while initializing the IO thread in speaker process. The process will be restarted.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-LOCK_RECURSIVE Attempt to recursively lock net [pointer] (lock: [hex])
Explanation A software error has occurred whilst trying to lock a network entry in the BGP Table database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-MAX_VALUE_EXCEEDED The value of [chars] ([unsigned int]) exceeds the maximum value: [unsigned int]
Explanation The value of an internally computed variable has exceeded the maximum value
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-MIB_INIT Initialization failed ([chars]%s)
Explanation An error occurred while initializing the BGP MIB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-NEGCOUNTER Prefix-accepted counter negative for peer [chars], prefix [chars]
Explanation The counter value for accepted prefixes is wrong and less than zero
Recommended Action The counter can be corrected by resetting the session. However, the only behavior affected by an incorrect counter is enforcement of the 'max-prefix' command.
Error Message%ROUTING-BGP-3-NOMEM_RESET Failed to allocate memory for [chars], resetting neighbor
Explanation The requested operation could not be accomplished because of a low memory condition. One or more neighbor sessions have been reset to free some memory.
Recommended Action In the problem recurs, reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-BGP-3-NOMSGCHUNK Failed to allocate [unsigned int] bytes from the memory pool for message of type [unsigned int]
Explanation A request was made to allocate a message size for which there was no memory pool large enough. This may indicate a software error in the calculation of the requested size.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ORA_INSTBUILD Failed to build [chars]: [chars] ([chars])
Explanation Internal error in the routing policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ORA_ORABUILD Failed to build ORA[chars]: [chars] ([chars])
Explanation There was an internal error in the routing policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ORA_RUN Could not apply policy operation [chars] to attribute [chars] because [chars]
Explanation Internal error in the routing policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-REDIST_FAIL Failed to register with the RIB for redistribution of [chars] [chars] [chars] routes: [chars]
Explanation A RIB client library call for redistribution of routes failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-RIB_CONN_FAIL Failed to open connection to the RIB for address family [unsigned int]: [chars]
Explanation The connection to the RIB could not be established and a retry timer could not be started
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-RIB_FAIL Failed to [chars] for [chars] while calling the RIB: [chars]
Explanation A RIB library call failed unexpectedly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-RIB_INIT Initialization failed ([chars]%s)
Explanation An error occurred while initializing the BGP RIB thread. The process will be restarted if this error occurs during process startup.
Recommended Action If the process has been restarted and the problem recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-RIB_INIT_FAIL Initialization to RIB failed for [chars]: [chars]
Explanation An error occurred whilst initialising the RIB for a new address family. This could be caused by failure to allocate resources or by errors when calling the Table Resource Manager or the RIB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-RIB_RETRY_FAIL RIB route retry failure: [chars] for [chars]
Explanation Some routes were not successfully installed in the RIB. Consequently, an attempt was made to save these routes to retry later. However, an error was encountered during the save attempt.
Recommended Action Issue a 'clear route ' to cause BGP routes to be reinstalled in the RIB. If this does not work, issue a soft or hard reset to all peers.
Error Message%ROUTING-BGP-3-RIB_TABLE_FAIL Failed to [chars] for [chars], RIB table [unsigned int]
Explanation An error was encountered during some operation for the specified address family and RIB table. This could be due either to a lack of resources or a software problem.
Recommended Action Issue a 'clear route ' to cause BGP routes to be reinstalled in the RIB. If this does not work, issue a soft or hard reset to all peers.
Error Message%ROUTING-BGP-3-SPKR_INIT Initialization failed ([chars]%s)
Explanation An error occurred while initializing the BGP speaker process. If this occurred during process startup, then the process may be restarted.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-UNKNOWN_MEMSTATE BGP received a notification about an unknown memory state ([unsigned int])
Explanation BGP received a low memory notification from wdsysmon for an unknown memory state, ie not NORMAL, MINOR, SEVERE or CRITICAL. As a result, no action was taken.
Recommended Action Check the memory on the node, and if it is low, take manual action to release memory, eg by resetting some BGP neighbors (using the 'clear bgp' command).
Error Message%ROUTING-BGP-3-UNLOCK_ERR Failed to unlock net [pointer] (lock: [hex])
Explanation A software error has occurred whilst trying to unlock a network entry in the BGP Table database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-4-ATTRKEY_INCONSISTENT BGP detected an inconsistency in attribute key generation. Will correct the problem by renumbering all attributes
Explanation The attribute key generation routine has gone beyond the checkpointed value. This is a rare condition to occur as the key generation algorithm is very simple.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-4-BFD_INVALID_NBR Attempt to register BFD session on invalid neighbor: [chars]
Explanation Internal error indicating that an attempt has been made to create a BFD session for a neighbor type that is not supported by BFD.
Recommended Action The BFD session for the neighbor in the log will not be created. If a BFD session for this neighbor is not required, no further action is needed. To re-attempt creation of a BFD session for this neighbor, remove and re-add the bfd fast-detect configuration for the neighbor.
Error Message%ROUTING-BGP-4-DESTROY_CHUNK Chunk pool [chars] is no longer in use but cannot be destroyed
Explanation 'BGP has resized its bit fields, so the old bit field chunks should be ' 'destroyable. Nonetheless, BGP is unable to destroy the old chunk and, ' 'hence, cannot release unwanted memory.'
Recommended Action This error will not cause any erroneous behavior, hence no further action is needed to rectify the situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-4-INCONSISTENT Detected inconsistent config state: [chars]
Explanation The internal state representing the configuration was invalid, but has now been fixed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-4-LOCK_ORDER Locking order violation (thread [unsigned int]): [chars] gained while holding: [chars]
Explanation BGP detected a violation of lock ordering requirements
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-4-LOCK_RELEASE Lock released without being held (thread [unsigned int]): [chars] gained [unsigned int], released [unsigned int]
Explanation BGP detected a lock being released when it was not held.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-4-MAXPFXEXCEED No. of [chars] prefixes received from [chars]: [unsigned int] exceed limit [unsigned int]
Explanation Number of prefixes received from a neighbor for a given address family has exceeded the limit configured with the 'max-prefix' command.
Recommended Action Check the prefixes received from the neighbor and verify whether the limit should be increased, or the neighbor is sending more prefixes than expected.
Error Message%ROUTING-BGP-4-NBR_NOPOLICY No [chars] [chars] policy is configured for eBGP neighbor [chars]. No [chars] prefixes will be [chars] the neighbor until [chars] policy is configured.
Explanation No routing policy has been configured for the specified eBGP neighbor in the given direction (inbound or outbound) for the address family named. To avoid unintended routing effects, no prefixes will be accepted in that direction until some policy is configured. 'Policy' can be a route-policy, or (for inbound policy) it can be a prefix list.
Recommended Action Configure a route-policy for the neighbor in the given direction. If the desired behavior is to accept/send all routes, the route-policy should contain the single statement 'pass'. If the desired behavior is not to accept/send any routes, the route-policy should contain the single statement 'drop'.
Error Message%ROUTING-BGP-4-POLICY_COMMUNITY_OVERFLOW Community overflow from policy application
Explanation Policy tried to add more communities than a BGP route can hold.
Recommended Action Find the affected neighbor with 'show bgp community truncated'. Modify policy on the affected neighbor to delete unnecessary communities.
Error Message%ROUTING-BGP-4-POLICY_IBGP [chars] operations in [chars] [chars] policy [chars] will be ignored for internal neighbor/update-group [chars]
Explanation A policy attached to an iBGP neighbor performs operations that are illegal for iBGP routes, such as modifying the AS-path or MED.
Recommended Action Modify the policy to avoid the prohibited operations.
Error Message%ROUTING-BGP-4-POLICY_NHOP_WRONGAFI The policy '[chars]' attempted to set a next-hop on [chars] with an unsuitable address type. The next-hop will not be modified.
Explanation The specified route-policy (or a policy applied by that policy) is configured - perhaps on a neighbor or for redistribution - and it is attempting to set the next-hop of the specified route to an address that doesn't match the address-family of the route. For example, it might be setting an IPv6 next-hop on an IPv4 route. Since this does not make any sense, the attempt will be ignored, and the next-hop will not be changed. (Note that this message is rate-limited, so it will not appear for every single route that is affected). Use the command 'show rpl policy attachpoints' to determine where this policy is in use. Use the command 'show rpl policy uses policies' to determine which other policies this policy applies (since the relevant 'set next-hop' may be in one of these policies).
Recommended Action Modify the policy so that it sets a next-hop that matches the type of route it is modifying.
Error Message%ROUTING-BGP-4-POTENTIAL_DEADLOCK Potential for deadlock detected: Locks: [chars]
Explanation BGP detected the potential for a deadlock to occur. The process will be restarted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-4-SPKR_RUNNING BGP AS number has changed from [unsigned int] to [unsigned int] - bgp (speaker) process will be restarted.
Explanation The bpm process was terminated improperly and the speaker process did not receive the notification to terminate. A new bpm process has started with a different AS number due to a new bgp configuration while the speaker process is still running with the previous AS number.
Recommended Action The speaker will be restarted to handle this error. No further corrective action is necessary. However, please contact your Cisco technical support representative to report this error.
Error Message%ROUTING-BGP-4-UNKNOWN_ACL Unknown ACL action: [unsigned int]
Explanation BGP received an unknown action (permit/deny/etc) from the ACL library
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-5-ADJCHANGE neighbor [chars] [chars] [chars]%s
Explanation A BGP neighbor has either come up or gone down. This message appears only if the bgp log neighbor changes command is configured for the BGP process.
Recommended Action This informational message normally appears as routers and BGP neighbors go up or down. However, unexpected neighbor loss might indicate high error rates or high packet loss in the network and should be investigated.
Error Message%ROUTING-BGP-5-BPM_ROUTER_ID No router ID available. Cannot connect to neighbors (retry in [unsigned int] seconds)
Explanation IPARM returned no valid router ID. This is due to lack of a global router ID or a loopback interface.
Recommended Action Try one of the following: 1) Set up a BGP router ID via the `bgp router-id' command in the `router bgp' configuration mode, or 2) Set up a global router ID via the `router-id' command in the global configuration mode, or 3) Set up a loopback interface with an IPv4 address.
Error Message%ROUTING-BGP-5-LOWMEM_RESET neighbor [chars] reset due to SEVERE low memory condition - use 'clear bgp [chars]' to re-enable
Explanation A SEVERE low memory condition has been encountered on the node where the BGP process is running, and so to free some memory, BGP has reset a neighbor. BGP will continue to reset neighbors periodically until the low memory condition abates. The neighbors which are reset will be shut down until a 'clear bgp' command is used to bring them back up. They will not come up automatically when the low memory condition abates - this is to prevent the node oscillating between memory states.
Recommended Action Free some memory on the system or correct the condition causing the low memory problem, and then use the 'clear bgp ' command to re-enable the neighbors that have been shut down. The 'show bgp all all summary' command can be used to easily see which neighbors are affected.
Error Message%ROUTING-BGP-5-LOWMEM_SHUTDOWN BGP is shutting down due to [chars] low memory condition - use 'process restart bgp location ' to restart
Explanation BGP received a notification that CRITICAL low memory state has been entered, or that SEVERE low memory state has been entered while BGP is in READ-ONLY mode, and consequently it has shut itself down in order to free memory.
Recommended Action Check the memory on the node, and take steps to free memory or to correct the condition which caused the low memory state. Then restart the process using the 'process restart bgp location ' command.
Error Message%ROUTING-BGP-5-MAXPFX No. of [chars] prefixes received from [chars] has reached [unsigned int], max [unsigned int]
Explanation Number of prefixes received from a neighbor for a given address family has reached the warning level configured with the 'max-prefix' command.
Recommended Action Check the prefixes received from the neighbor and verify whether the limit should be increased, or the neighbor is sending more prefixes than expected.
Error Message%ROUTING-BGP-5-POLICY_RESET Policy configuration change on neighbor [chars] requires HARD reset (clear bgp [chars]) to take effect.
Explanation Automatic soft reset on policy change is not possible as the neighbor does not support ROUTE_REFRESH and 'soft-reconfiguration inbound' is not configured.
Recommended Action Manually clear affected peer at earliest convenience, in order for policy change to take effect.
Error Message%ROUTING-BGP-6-WARNING_WRAPPER Warning: A call to [chars] failed unexpectedly: [chars]
Explanation A function call failed unexpectedly - this is probably a system problem
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-7-BPM_CHKPT Failed to checkpoint allocation of [chars] to speaker [unsigned int]
Explanation The BPM failed to record the allocation in the checkpoint table. This could cause operational problems if the BPM is later restarted.
Recommended Action No further action is necessary unless the BPM restarts. In that case, if problems are seen it may be necessary to deconfigure BGP completely and then reconfigure it.
C12000_IPV4_MRIB Messages
Error Message%ROUTING-C12000_IPV4_MRIB-3-IFH_ERR Failed to [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-C12000_IPV4_MRIB-3-IM_NAME_ERR im_interface_name error in function [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-C12000_IPV4_MRIB-3-MEM_ERR Failed to [chars] for [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
CLNS Messages
Error Message%ROUTING-CLNS-2-LC_INPUT Unexpected packet num [unsigned int] received on the LC
Explanation CLNS on the LC doesnot process any packet. It will ignore any packets it receives on the LC.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ASYNC_ATTACH Failed to setup ingress packet handler for NetIO: [chars]
Explanation CLNS encounted errors when initializing its connection with NetIO.
Recommended Action CLNS will restart and try to recover. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-CONFIG_INIT Cannot initialize CLNS configuration: [chars]
Explanation CLNS could not initialize its configuration mechanism, and all future CLNS configuration will fail.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-DETACH Socket closing on interface [chars] failed: [chars]
Explanation The socket cannot remove an interface when closing.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-DLL_REGISTER Registration for '[chars]' failed: [chars]
Explanation Some internal initializations fail miserably!
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-EDM_CLIENT Error during operation '[chars]': [chars]
Explanation CLNS EDN client (usually a show command) failled to perform certain operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-EDM_ENCODE_FAILED Bad encoding failed for [chars]: [chars]
Explanation CLNS failed encode a bag for EDM.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-EDM_INIT Operation '[chars]' during EDM initialization failed: [chars]
Explanation CLNS show command failed to initialyze the EDM server. 'show' command will likely fail, although CLNS should be able to operate.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ERR_DEBUG_PACKET_INIT CLNS NetIO packet debugging failed to initialize.
Explanation CLNS failed to initialize packet debugging functions.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ERR_DEBUG_RETRIES_EXCEEDED Stopping CLNS debug initialization attempts after [unsigned int] tries
Explanation CLNS tried to initialize packet debugging functions but was unable to succeed even after a number of attempts. No more attempts will be made.
Recommended Action No action is required.
Error Message%ROUTING-CLNS-3-ERR_DROP_PKT [chars]. Dropping packet
Explanation CLNS encountered an internal error while trying to process a packet (usually for output). As a result CLNS dropped the packet.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ERR_INTERFACE_DATA CLNS was unable to resolve an interface while installing cap/decap chain.
Explanation CLNS was unable to look up local interface information. As a result the system may not be able to send/receive ISIS packets over this interface. This may be due to problems with either CLNS or the forwarding infrastructure.
Recommended Action Restarting the CLNS process may clear the error condition. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ERR_MEDIA_REGISTER CLNS failed to register media callback with netio: [chars]([dec])
Explanation CLNS failed to register for media callback with netio during initialization. As a result, CLNS will not be able to add its caps and wont receive or send packets. It's an internal error.
Recommended Action Restarting CLNS and/or Netio may clear the error condition. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ERR_NETIO_ENCAP_CALLBACK CLNS netio encap callback for media caps: [chars]([dec]) failed [chars]([dec])
Explanation CLNS failed to setup encap callback with this particular media or base capsulation. As a result CLNS will not be able to receive CLNS packets on this caps on any interface on this node.
Recommended Action Restarting CLNS and/or Netio may clear the error condition. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ERR_NETIO_SET_MAPPING CLNS netio set mapping for media caps: [chars]([dec]) failed [chars]([dec])
Explanation CLNS failed to setup mapping with this particular media or base capsulation. As a result CLNS will not be able to receive CLNS packets on this caps on any interface on this node.
Recommended Action Restarting CLNS and/or Netio may clear the error condition. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ERR_PARTNER_LOOKUP CLNS-NetIO partner lookup failed
Explanation NetIO was unable to initialize the CLNS partner process. As a result the system will not be able to send/receive ISIS packets over interfaces on this line card.
Recommended Action Restarting CLNS and/or NetIO may clear the error condition. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ERROR_INIT Cannot register CLNS error codes: [chars]
Explanation CLNS could not initialize its error code. CLNS will work, but error messages won't be user friendly!
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ETHERENCAP Incorrect MAC address length [dec]
Explanation The MAC address length provided for the ethernet encapsulation is wrong.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-EVENT_CONN_CREATE_FAIL Error creating '[chars]' connection: [chars]
Explanation CLNS failed to create a connection to an essential service during initialization. This is an internal error. It requires a restart of the process for recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-EVENT_CONN_NOTIFY_FAIL Error registering for critical events on '[chars]' connection: [chars]
Explanation During initialization, CLNS failed to register for essential notifications regarding the state of the connection for the specified service. This is an internal error. It requires a restart of the process for recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-EVM_INIT Error while initializing the [chars]: [chars]
Explanation An operation failed during the initialization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-GET_TRAFFIC Cannot get traffic information: [chars]
Explanation CLNS show command failed to get the required information.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-HSSD_REGISTER_FAIL CLNS failed to register for an HSSD area: [chars]
Explanation CLNS failed to register for an HSSD area. This is an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-IDB_SOCK Error removing interface ([hex]) from the clns socket: [chars]
Explanation An operation failed during the interface deletion.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-INTERFACE Operation '[chars]' on CLNS interface [chars] failed: [chars]
Explanation CLNS could not initialize its interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-L2INFO_LEN [chars] length is [dec], should be [dec]
Explanation The length of the L2 data received is not what it should be.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-LPTS_ADD_BINDING Couldn't add clns binding to lpts port arbitrator, error = [chars]
Explanation The clns process was unable to add a binding to LPTS. This is an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-LPTS_DELETE_BINDING Couldn't delete CLNS binding from Port Arbitrator, result = [chars]
Explanation The clns process was unable to delete a binding from LPTS. This is an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-LPTS_SETOPT Cannot set the LPTS option '[chars]': [chars]
Explanation An operation failed during LPTS option setting.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-PAK Packet operation '[chars]' failed: [chars]
Explanation An operation failed during packet handling.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-PAK_READ Failed to read data from packet area: [chars]
Explanation The clns process was unable to read the input packet. This is an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-PFI_INIT_FAILED PFI Initialization failed: [chars]
Explanation An operation failed during the Packet Forwarder Interface initialization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-SEND_ASYNC CLNS was unable to wake itself up([dec]) for reading pending packets: [chars]
Explanation CLNS is unable to wake up itself to read the pending ingress packets from NetIO. ISIS will not be able to receive these pending packets from CLNS.
Recommended Action Restarting CLNS might help. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-SOCK_INIT Socket initialisation task '[chars]' failed: [chars]
Explanation An operation failed during socket initialisation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-SOCK_SET_NAME Internal socket error on packet reception: [chars]
Explanation An operation failed during packet reception.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-SOCKET_PARSE_PATH error encountered when parsing path: [chars]
Explanation CLNS was unable to extract the xipc & job id from the socket path. This might cause communication problems between ISIS and CLNS.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-SOCKET_RESMGR_ATTACH Failed to setup the clns socket as a resource manager: [chars]
Explanation The clns process failed to advertise itself to the system as a resource manager.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-STATSD_INIT Cannot connect to the stats server: [chars]
Explanation An operation failed during the Stats Server Connection opening.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-STATSD_REGISTER Cannot [chars] with the stats server for interface ([hex])
Explanation An operation failed during the Stats Server Interface registration.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-TIMESTAMP Operation '[chars]' failed during packet timestamping: [hex] ([chars])
Explanation An operation failed during timestamp processing.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-BASE_CAPS_LU_FAIL IM base capsulation lookup for interface ([hex]) failed: [hex], '[chars]'
Explanation The Interface Manager returned an unexpected error when CLNS attempted to lookup an interface's base capsulation type. This may be a resource problem but is probably an internal error.
Recommended Action Consider restarting the CLNS and/or Interface Manager processes. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-DEBUG_REGISTER_FAIL Failed to register with the debugging subsystem: [hex], '[chars]'
Explanation CLNS failed to register with the debugging subsystem. If this message has been generated then CLNS debugging may not be available. This may be a system resource problem.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-GET_MCASTADDR_ERR Failed to get MAC address(im_attr_macaddr_get) for [chars]: [chars]
Explanation The process failed to get MAC address from the interface. This can be caused by a faulty hardware.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-IM_CRE_REG_FAIL CLNS interface registration failed for base cap type [chars]: [chars]
Explanation CLNS process failed to register an interface with the Interface Manager. This is an internal error. It requires a restart of process for recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-IM_SERV_BIND_FAIL Failed to bind to the Interface Manager: [dec]
Explanation CLNS failed to bind to the Interface Manager control plane. It's an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-IM_SIGEVENT_FAIL IM control handler setup failed: [chars]
Explanation CLNS failed to establish signal event in the Interface Manager control plane. It's an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-MAC_SIZE_ERR Incorrect MAC address size for [chars] (returned: [dec], expected: [dec])
Explanation MAC address size does not match IEEEBYTES (6 bytes). This can be caused by a faulty hardware.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-NETIO_OUTPUT_FAIL Failed to send packet 0x[pointer] to NetIO: [chars]
Explanation CLNS was not able to send a packet to NetIO. This could be because of communication problems between CLNS and NetIO.
Recommended Action If this message is seen during transient conditions, for example when NetIO is restarting either because of install operation OR because NetIO crashed then it is not harmful unless you see ISIS adjacencies dropping. If it is seen under steady state conditions OR If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-PAK_FROM_ISIS_FAIL Failed to process packet 0x[pointer] from ISIS: [chars] [chars]
Explanation CLNS was not able to process a packet from ISIS successfully and hence dropped the packet.
Recommended Action This message could be seen under low packet memory conditions and should recover once packet memory becomes available to CLNS. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-PAK_FROM_NETIO_FAIL Failed to process packet 0x[pointer] from NetIO: [chars]:[chars]
Explanation CLNS was not able to process a packet from NetIO successfully and hence dropped the packet.
Recommended Action This message could be seen under low packet memory conditions and should recover once packet memory becomes available to CLNS. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-SEND_HELLO_PDU_TO_ISIS_FAIL Failed to send Hello PDU(0x[pointer]) type [hex] from interface ([hex]) to ISIS instance [chars]: [chars]
Explanation CLNS was not able to send a hello class PDU to ISIS. This could be because of communication problems between CLNS and ISIS.
Recommended Action If this message is seen during transient conditions, for example when ISIS is restarting either because of install operation OR because ISIS crashed then it is not harmful. If the error message says out of memory, it is because of the queue between CLNS and ISIS being FULL which could either be because traffic rate is very high or ISIS might not be reading the packets. If it is seen under steady state conditions OR adjacency flaps are seen on this interface OR If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-SEND_PDU_TO_ISIS_FAIL Failed to send PDU(0x[pointer]) type [hex] from interface ([hex]) to ISIS instance [chars]: [chars]
Explanation CLNS was not able to send non-Hello class PDU to ISIS. This could be because of communication problems between CLNS and ISIS.
Recommended Action If this message is seen during transient conditions, for example when ISIS is restarting either because of install operation OR because ISIS crashed then it is not harmful. If the error message says out of memory, it is because of the queue between CLNS and ISIS being FULL which could either be because traffic rate is very high or ISIS might not be reading the packets. If it is seen under steady state conditions OR If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-UNKNOWN_MEDIA Unknown media ([dec]) on interface ([hex])
Explanation The specified interface media is not supported by CLNS. This means that IS-IS and other CLNS protocols cannot run over the specified interface. This is an internal programming error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.. As a workaround consider using a different encapsulation for the interface.
Error Message%ROUTING-CLNS-7-CAPS_ADD_FAIL Failed to add CLNS encapsulation to interface ([hex]): [chars]
Explanation CLNS failed to add caps to its encapsulation chain. It's an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-7-CONN_PAK_AREA_FAIL CLNS failed to connect to packet area
Explanation CLNS failed to connect to packet subsystem during initialization. As a result, CLNS will not be able to receive or send packets. It's an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-7-ERR_L2_HASH CLNS failed to initialize the L2 hash function: [chars]
Explanation CLNS failed to initialize the L2 hash function. It's an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-7-ERR_STACKMEM Could not alloca [dec] bytes
Explanation CLNS failed to allocate stack memory space.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-CLNS-7-IM_ATTR_REG_FAIL Failed to register for notification of MAC address: [chars]
Explanation An error was discovered during the Interface Manager MAC address registration. It requires a restart of process for recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
DAD Messages
Error Message%ROUTING-DAD-3-BIND_FAILURE Sysdb bind operation failed because: [chars]
Explanation The bind operation has failed for the above reason. This is something that should not occur under normal operations.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-DAD-3-CLEANUP_FAILURE Unable to listen for cleanup notices because: [chars]
Explanation A failure occured while trying to ask sysmgr for cleanup events for package un-installs.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-DAD-3-DELETE_FAILURE Sysdb delete operation failed because: [chars]
Explanation The DAD library attempts to delete the old protocol information before writing out the new information. This delete operation failed for the above reason.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-DAD-3-EVENT_FAILURE Unable to listen for events because: [chars]
Explanation A failure occured while trying to setup the event listen structure for package un-installs.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-DAD-3-PROC_AVAILABLE_FAILURE Unable to declare proc available because: [chars]
Explanation A failure occured while trying to tell sysmgr that we are available for availability.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-DAD-3-PROC_READY_FAILURE Unable to declare proc ready because: [chars]
Explanation A failure occured while trying to tell sysmgr that we are ready for processing.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-DAD-3-SETUP_FAILURE Invalid setup at [chars]@[dec]: [chars]
Explanation There was something illegal about the setup operations that where performed. This should be a straight coding error that will fail everytime and should be cleaned up before releasing the code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-DAD-3-WRITE_FAILURE The writing of sysdb information failed because: [chars]
Explanation The DAD library encountered an error while writing out the policy information for the above reason.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
EVENT Messages
Error Message%ROUTING-EVENT-2-INIT_FAIL Init failure, [chars]: [chars], process terminated
Explanation An error occurred during initialization, causing the process to terminate.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EVENT-2-NOMEMORY No memory, [chars]: [chars]
Explanation Allocation of the specified resource failed because of a low memory condition.
Recommended Action This indicates a low memory condition. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-EVENT-2-NOMEMORY_FATAL No memory, [chars]: [chars], process terminated
Explanation Memory allocation of a critical EVENT resource failed because of a low memory condition. The EVENT process was terminated.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EVENT-3-ALLOC_ERR Allocation error, [chars]: [unsigned int] bytes for [chars]
Explanation EVENT was unable to allocate memory for the specified resource.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EVENT-3-EXTERNALERR External error, [chars]: [chars]
Explanation An external software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EVENT-3-EXTERNALERR_RC External error, [chars]: [chars], error [hex]
Explanation An external software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EVENT-3-IFMGR External IFMGR error, [chars]: [chars], error [chars] [[hex]]
Explanation The specified interface manager request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EVENT-3-INIT_ERR Init error, [chars]: [chars], error [hex]
Explanation An error occurred during initialization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EVENT-3-INTERNALERR Internal error, [chars]: [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EVENT-3-INTERNALERR_RC Internal error, [chars]: [chars], error [hex]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EVENT-3-SYSDB External SysDB error, [chars]: [chars], error [chars] [[hex]]
Explanation An external EVENT error occurred when accessing the system database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
FIB_ForUs Messages
Error Message%ROUTING-FIB_ForUs-3-LIB_DEBUG_INIT The ForUs client library debug failed to initialize, event: [chars], error: [chars]
Explanation Initialization of debugging in the ForUs client library failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
FIB Messages
Error Message%ROUTING-FIB-1-DLLOPEN failed to open dll: [chars]
Explanation The specified DLL could not be found.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-1-FIBALLOC [chars]: [chars]
Explanation The CEF system could not allocate the data structures needed to initialize a new forwarding table.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-1-FIBTBLINIT CEF table creation failure, id:[dec] [chars]
Explanation An internal software error occurred that prevented the creation of a new forwarding table.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-1-MTRIE_ROOT [chars]: mtrie [dec]-8-8 is not supported
Explanation Depending on the platform, the CEF system supports either an 8-8-8-8 or 16-8-8 radix trie (mtrie) for IP lookups.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-BGP_ATTR_INSERT_DROP Attribute [hex] insert failed [hex], [chars].
Explanation FIB is dropping this attribute due to error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-DFIBSWITCH Error trying to turn on Distributed CEF without CEF on
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-IDBINIT Error initializing CEF IDB table
Explanation Initialization of the CEF IDB table could not be accomplished because of a low memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-FIB-2-INIT IP CEF initialization failure: [chars]
Explanation Initialization of CEF failed
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-LINECARDINIT Error initializing CEF Linecard queue
Explanation Initialization of the CEF linecard queue could not be accomplished because of a low memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-FIB-2-MSG_CHUNK Lincard CEF message chunk corrupted. Corrected and recovered
Explanation Initialization of the linecard CEF message chunk not done properly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-NOMEM_ROUTEDROP_ADDMODIFY Dropping add/modify route [chars]/[unsigned int] msg due to low memory.
Explanation FIB is not adding or modifying this route due to a low memory condition.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-NOMEM_ROUTEDROP_DEL Dropping delete route [chars]/[unsigned int] msg due to low memory.
Explanation FIB is not deleting this route due to a low memory condition.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-NOMEMINFO_ROUTEDROP Dropping route [chars]/[unsigned int] due to no knowlege of memory available. err [hex], [chars].
Explanation FIB is dropping this route because it is unable to find the memory available.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-NOMEMINFO_SHMERR Dropping routes due to no knowlege of memory available. err [hex], [chars].
Explanation FIB is dropping this route because it is unable to find the memory available.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-RADIXINIT Error initializing IP CEF radix tree
Explanation Initialization of the radix tree could not be accomplished because of a low memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-FIB-2-ROUTEDROP_UPD Dropping route update to [chars]/[unsigned int] path [dec] interface [hex]
Explanation FIB is not processing this route update due to internal error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-XDRINIT Error initializing CEF xdr chunks
Explanation Initialization of the CEF xdr chunks could not be accomplished because of a low memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-FIB-3-ADD CEF : fail to add route for [chars] [unsigned int]
Explanation CEF fails to add a prefix entry.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-ADJ_GET_L2 no adj_get_l2 function
Explanation adj_get_l2 function was not provided.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-ADJ_GET_L2_NULL adj_get_l2 function returned null for [chars], bucket [dec]
Explanation adj_get_l2 function returned a null for this adjacency.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-BCDL BCDL failed during [chars]: [chars]
Explanation An internal software error occurred that prevented the FIB from working properly with BCDL.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-CFGREG Config registration error: [chars] [chars]
Explanation An internal software error ocurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.*
Error Message%ROUTING-FIB-3-CLIENT CEF CLIENT: [chars] [chars]
Explanation CEF client internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-DELETE CEF : fail to delete route for [chars] [unsigned int]
Explanation CEF fails to delete a prefix entry.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-FIBDISABLE Fatal error, slot [dec]: [chars]
Explanation An internal software error occurred. CEF switching disabled on this slot.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-FIBGTRIEINIT Gtrie initialization default value failed, [chars] [chars]
Explanation An internal software error occurred that prevented the FIB subsystem from starting
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-FIBLC_OOSEQ Slot [dec] disabled - Out of Sequence. Expected [dec], received [dec]
Explanation An internal software error ocurred. CEF switching disabled on this slot.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-FIBSEQ Out of sequence. State [dec] Rcvd [dec]
Explanation An internal software error occurred. CEF switching disabled on this slot.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-GTRIE_DEL Gtrie delete failed, [chars]/[unsigned int] (Err: [hex], [chars])
Explanation An internal software error occurred that prevented the FIB subsystem from removing a route
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-MTU Unable to obtain MTU information for [chars] ([dec])
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-NDB Prefix [chars][dec] received with zero total traffic count
Explanation An internal software error ocurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-NOMEM Malloc Failure, [chars]
Explanation An internal software error ocurred. CEF switching disabled on this slot.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-NOTABLE Failed to find CEF forwarding table [chars]
Explanation An internal software error ocurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-PFI_IFINFO CEF : [chars] ifh:[hex], if:
Explanation CEF fails to connect or get information from pfi_ifh server,
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-RCC CEF : rt_check_send_msg failed: [chars]
Explanation CEF fails to send rcc error messages,
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-RCC_TABLE RCC failed finding [chars] table
Explanation The Route Consistency Checker failed finding specified table.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-RECEIVE Tag-switching called for RECEIVE entry [chars][dec]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-RPCINIT Unable to initialize CEF RCP handler: [chars] program [dec] version [dec] protocol [dec]
Explanation The CEF system could not initialize an RPC server and therefore cannot handle show and clear commands from the parser.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-SERVER CEF SERVER: [chars] [hex]
Explanation CEF server internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-SERVER_CERR CEF SERVER: [chars] [chars]
Explanation CEF server internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-SERVER_DLL_CERR CEF SERVER: [chars] [chars] ([chars])
Explanation CEF server internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-SHMEM Shared memory failure: error code [dec], [chars]
Explanation An internal error ocurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-STATS CEF : failed to get [chars] counters for ifh:[hex] ([dec], [chars])
Explanation CEF fails to read stats
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-SYSDB Failed to parse notify parameters for [chars]
Explanation An internal software error ocurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-THREAD Thread processing error: [chars]
Explanation An internal software error ocurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-FIBEVENT Invalid event. Type [dec], event [dec]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-FIBIDB Missing cef idb for ifh:[hex], , during [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-FIBIDB_LOOKUP_FAILED FIB idb lookup failed ifh [hex], if: [chars]: [hex], [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-FIBMSG Invalid message received. Type [dec], event [dec], length [dec]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-FIBSPECIALPREFIX Invalid Special Prefix Type. Type [dec]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-FIBXDRINV Invalid format. [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-FIBXDRLEN Invalid XDR length. Type/event [dec]/[chars]. XDR [dec], buffer [dec]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-HA [chars]: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-IM_CONN fail to connect to IM [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-LTRACE_ERROR Failed to open LTrace file: [chars]
Explanation The FIB process was unable to open the LTrace buffer for automatic tracing (show ltrace cef may not work).
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-PFI_IFH_CONN fail to connect to PFI_IFH [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-PFI_IFH_LOOKUP fail to lookup information in PFI_IFH [chars] for ifh [hex]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-RADIXINSERT Error trying to insert prefix entry for [chars]/[dec]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-RATE [chars] rate limit status [dec]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-WARNING FIB internal error [chars]: [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-6-DEBUG_REG IPV4-FIB: Debug registration failed: [chars]
Explanation Debug message registration failed
Recommended Action No action is required.
GSR_MLIB Messages
Error Message%ROUTING-GSR_MLIB-3-INIT_MSG [dec] [chars] [chars]
Explanation Internal error. Failed to initialize mlib or IDB
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
GSR_mpls_hwdrv Messages
Error Message%ROUTING-GSR_mpls_hwdrv-3-RES_ERROR Error: [chars]: Err=[chars]
Explanation A error occurred in GSR mpls Edge h/w driver resulting in a failure to provide some system service as indicated in the message text.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%ROUTING-GSR_mpls_hwdrv-6-INFO_MSG Info: [chars]
Explanation This is a Informational message in the GSR mpls driver to indicate an operation.
Recommended Action No action is required.
HFR_IPV4_MRIB Messages
Error Message%ROUTING-HFR_IPV4_MRIB-3-CHKPT_ERR Failed to [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-FGID_ADD_ERR Failed to add LC [dec] into FGID [dec]: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-FGID_BATCH_ADD_ERR Failed to add batch of LCs into FGIDs: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-FGID_BATCH_REMOVE_ERR Failed to remove batch of LCs from FGIDs: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-FGID_ERR Failed to [chars]: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-FGID_REMOVE_ERR Failed to remove LC [dec] from FGID [dec]: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-IFH_ERR Failed to [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-IM_NAME_ERR im_interface_name error in function [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-INTERNAL_ERR Failed to [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-INVALID_FGID_ERR Failed to [chars] : invalid fgid value [hex]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-MEM_ERR Failed to [chars] for [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-PERF_ERR Failed to [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IGMP_MTRACE Messages
Error Message%ROUTING-IGMP_MTRACE-3-EVENT_ERROR Event error: [chars] in [chars]
Explanation Event error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IGMP_MTRACE-3-INIT_ERROR Init error: [chars]
Explanation Initialisation error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IGMP_MTRACE-3-MEMORY_ERROR Memory error: [chars] in [chars]
Explanation Memory error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IGMP_MTRACE-3-MSG_ERROR msg error: [chars] in [chars]
Explanation Messaging error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IGMP_MTRACE-3-SOCKET_ERROR Socket error: [chars] in [chars] : [chars]
Explanation Socket error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IP_STATIC Messages
Error Message%ROUTING-IP_STATIC-3-ARM_EVENT Error processing [chars] event for [chars] from IP ARM, table [unsigned int] : [chars]
Explanation A static routing process failed unexpectedly when processing an IP address change event. This may lead to spurious or missing connected and local routes in the routing table.
Recommended Action *RECUR*
Error Message%ROUTING-IP_STATIC-3-IDB_DELETE Failed to delete idb for interface [chars] from '[chars]' thread
Explanation The static routing process failed unexpectedly to delete an interface descriptor block from the idb WAVL tree.
Recommended Action *SUPPORT*
Error Message%ROUTING-IP_STATIC-3-IFDB_WALK Failed walking topologies after interface state change for interface [chars]: [chars]
Explanation The static routing process failed unexpectedly to walk the topology trees after receiving an interface state change notification.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-IM_INTERFACE_CREATE Error handling create event for interface [chars]: [chars]
Explanation The static routing process failed to correctly handle a create event for an interface which it was tracking.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-IM_INTERFACE_UNREGISTER Failed to unregister interface notification with IM for interface [chars]: [chars]
Explanation The static routing process failed unexpectedly to unregister an interface resolution event. Future up/down events on the interface may cause further messages to be generated by the static process.
Recommended Action *SUPPORT*
Error Message%ROUTING-IP_STATIC-3-IM_REGISTER Failed to [chars] with IM for state events on [chars]: [chars]
Explanation The static routing process failed unexpectedly to register for notification with Interface Manager. Future up/down events on the interface will probably not have the correct effect on the installation and withdrawal of static routes in the routing table.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-INTERNAL [chars]: [chars]
Explanation The static routing process has either failed a function that expected to succeed, or has got into an inconsistent state.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-NHDB_DELETE Failed to delete nhdb for next-hop [chars] for table [unsigned int]
Explanation The static routing process failed unexpectedly to delete an next-hop descriptor block from the nhdb AVL tree.
Recommended Action *SUPPORT*
Error Message%ROUTING-IP_STATIC-3-PATH_BP_DELETE Failed to delete backpointer to path [chars]/[unsigned int] from [chars] [chars]
Explanation The static routing process failed unexpectedly to delete a path from an interface or next-hop descriptor block's path backpointer list.
Recommended Action *SUPPORT*
Error Message%ROUTING-IP_STATIC-3-RIB_BATCH [chars]: Failed to send RIB batch buffer re-populating RIB for table [unsigned int]: [chars]
Explanation The static routing process failed unexpectedly to update RIB with a batch of updates.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-RIB_CLEAR_PREFIX Error re-installing route after a clear table event for prefix [chars]/[unsigned int] in table [unsigned int]: [chars]
Explanation There was an error re-installing a route in the RIB after receiving a 'clear prefix' event.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-RIB_CLEAR_TABLE Error re-installing routes after a clear table event for table [unsigned int]: [chars]
Explanation There was an error re-installing routes in the RIB after receiving a 'clear table' event.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-RIB_CLEAR_UNKNOWN_PREFIX Received a clear event for unknown prefix [chars]/[unsigned int] in table [unsigned int]
Explanation The static routing process received a clear event from RIB for a prefix which it was not tracking.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-RIB_CLEAR_UNKNOWN_TABLE Received a clear event for unknown table [unsigned int] (Prefix [chars])
Explanation The static routing process received a clear event from RIB for a table which it was not tracking.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-RIB_ECMP Failed to update RIB after ECMP recalculation for table [unsigned int], prefix [chars]/[unsigned int]: [chars]
Explanation The static routing process failed unexpectedly to update RIB after an ECMP recalculation.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-RIB_FETCH Error fetching event from RIB: [chars]
Explanation The static routing process failed unexpectedly to fetch a notification event from RIB.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-RIB_FULL Failed to update RIB during full topology download for table [unsigned int], prefix [chars]/[unsigned int]: [chars]
Explanation The static routing process failed unexpectedly to update RIB after RIB restarted.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-RIB_INTERFACE Failed to update RIB for table [unsigned int], prefix [chars]/[unsigned int], after receiving interface state event for [chars]: [chars]
Explanation The static routing process failed unexpectedly to update RIB after an interface state change event.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-RIB_NEXTHOP Failed to update RIB for table [unsigned int], prefix [chars]/[unsigned int] after receiving next-hop resolution event for [chars]: [chars]
Explanation The static routing process failed unexpectedly to update RIB after a next-hop resolution event.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-RIB_NEXTHOP_PREFIX Received a change event for unknown next-hop [chars] in table [unsigned int]
Explanation The static routing process received a change notification event from RIB for a next-hop which it was not tracking.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-RIB_NEXTHOP_UNKNOWN_TABLE Received a next-hop change event for unknown table [unsigned int] (Prefix [chars])
Explanation The static routing process received an event from RIB for a routing table which it was not tracking.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-RIB_NEXTHOP_UNREGISTER Failed to unregister next-hop notification with RIB for table [unsigned int], prefix [chars]: [chars]
Explanation The static routing process failed unexpectedly to unregister a next-hop resolution event. Future state change events on the next-hop may cause further messages to be generated by the static process.
Recommended Action *SUPPORT*
Error Message%ROUTING-IP_STATIC-3-RIB_TOO_MANY_PATHS Prefix [chars]/[dec]: Maximum path count exceeded. Please remove (next-hop [chars], interface [chars]) from the running configuration.
Explanation The maximum allowed number of next-hop paths for a single destination prefix has been exceeded. One or more paths have not been installed in the RIB, and should be removed from the running configuration.
Recommended Action Excess next-hop paths should be removed from the running configuration.
Error Message%ROUTING-IP_STATIC-3-SHUTDOWN Process is shutting down: [chars]
Explanation The static routing process has performed a graceful shutdown and will be restarted.
Recommended Action Check to make sure the process has restarted. If not, restart manually Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-TDB_DELETE Failed to delete tdb for table [unsigned int]'
Explanation The static routing process failed unexpectedly to delete a table descriptor block from the tdb AVL tree.
Recommended Action *SUPPORT*
Error Message%ROUTING-IP_STATIC-3-UPDATE_COMPLETE Failed to send 'update complete' notification to RIB for table [unsigned int]: [chars]
Explanation The static routing process unexpectedly failed an attempt to signal to the RIB that the given table is now in sync
Recommended Action Check the routing table to see whether any static routes are missing, and whether the protocol is in sync. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-6-CONFIG_MAXIMUM_CHANGE The maximum number of configurations for static routes has been changed from [unsigned int] to [unsigned int]
Explanation The maximum number of static route configurations which may be entered has been changed.
Recommended Action Refer to the configuration guidelines for the maximum allowed limit for static routes
Error Message%ROUTING-IP_STATIC-7-ARM_DUPLICATE Received duplicate IP address notification from IP ARM for interface [chars]
Explanation A static routing process incorrectly received a duplicate IP address notification from IP ARM.
Recommended Action *SUPPORT*
Error Message%ROUTING-IP_STATIC-7-IM_INTERFACE_EVENT Received a [chars] event for unknown interface [chars]
Explanation The static routing process received a change notification event from Interface Manager for an interface which it was not tracking.
Recommended Action Check the routing table to see whether any static routes are missing. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPMC_GTRIE_DEBUG Messages
Error Message%ROUTING-IPMC_GTRIE_DEBUG-3-ERR [chars]
Explanation This is a catch all error message. It usually means an uncorrectible problem
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPMC_GTRIE_DEBUG-3-INIT_ERR [chars] [dec] [chars] [dec] [chars]
Explanation Internal error. GTRIE debug library initilization failed
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPMC_GTRIE_DEBUG-6-TERM_ERR [chars] [dec] [chars] [dec] [chars]
Explanation Internal non-serious error. GTRIE debug library termination failed
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPMC_GTRIE_DEFAULT Messages
Error Message%ROUTING-IPMC_GTRIE_DEFAULT-2-FATAL [chars]
Explanation Internal error. Usually sever problems such as failing to free memory
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPMC_GTRIE_DEFAULT-3-INIT_ERR [chars]
Explanation Error while initializing Gtrie. Initialization failed and aborted
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPMC_GTRIE_DEFAULT-4-INIT_WARN [chars]
Explanation Error while initializing Gtrie. Initialization will continue
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPMC_GTRIE_DEFAULT-4-WARN [chars]
Explanation Internal error. A significant event but we can still continue
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV4_ADJ Messages
Error Message%ROUTING-IPV4_ADJ-3-ADD_DB_MALLOC_FAILED Malloc Failure in trying to add adj for [chars]
Explanation An internal software error ocurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_ADJ-3-ENT_UPDATE Update for ifh:[hex], if:, [chars] skipped. Reason: either no fib or netio IDB
Explanation The layer 2 adjacency could not be installed for the interface. This might cause problems in forwarding traffic to this interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_ADJ-3-L2_LOADHASH_FAILED Could not register ipv4 l2 loadhash function with AIB. Error=[chars]
Explanation Call to register IPv4 l2 loadhash function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_ADJ-3-NO_FIBIDB IP-ADJ: No fibidb
Explanation Adding an adjacency to the adjacency database failed. Reason for this failure is no fib IDB
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_ADJ-4-ADD_DB Update for ifh:[hex], if:, [chars] failed. Unable to update database
Explanation The layer 2 adjacency could not be installed for the interface. This might cause problems in forwarding traffic to this interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_ADJ-4-CANNOT_CREATE Cannot create fidbidb for interface [chars]
Explanation The layer 2 adjacency could not be created for the interface.
Recommended Action Wait to see if the AIB recovers, othwerwise restart ipv4_aib
Error Message%ROUTING-IPV4_ADJ-4-LARGE_MAC IP-ADJ([chars]): macaddr change out of bounds
Explanation Extra large MAC change
Recommended Action No action is required.
Error Message%ROUTING-IPV4_ADJ-6-DEBUG_REG ipv4_adj: Debug registration failed: [chars]
Explanation Debug message registration failed
Recommended Action No action is required.
Error Message%ROUTING-IPV4_ADJ-7-INV_MSG_CODE Unknown aib message opcode [dec]
Explanation The event manager passed an unknown message code
Recommended Action No action is required.
Error Message%ROUTING-IPV4_ADJ-7-MSG_UNALIGNED Unaligned aib message
Explanation The received message was not aligned on a 4-byte boundary
Recommended Action No action is required.
IPV4_IGMP Messages
Error Message%ROUTING-IPV4_IGMP-3-CHUNK_ERR Failed to create chunk for [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-EDM_INIT ERROR : [chars] - [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-GROUP_ERR Group [chars] failed: [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IDB_ADD_ERR Fail to add [chars] into database
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IDB_FREE_ERR Fail to free [chars] from database: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IDB_INIT_ERR [chars] - [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IDB_LOST_GROUPS_ERR Local joined groups on [chars] will be lost
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IDB_STATE_MONITOR_ERR Fail to monitor interface state of [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IM_BATCH_STATE_ERR Invalid state for IM state registration batch on [chars] ([chars])
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IM_BULK_ERR Failed to [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-INIT_ERR [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-JOIN_IN_SSM_RANGE Join for group [chars] in SSM range. Join operation postponed
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-LTRACE_ERR Failed to [chars]: [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-MRIB_CONN_ERR MRIB connection error - [chars] in [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-NET_ERR [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-SOCK_ERR [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-SYSDB_BIND_ERR Sysdb Bind error for [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-SYSDB_BSCAN_ERR Sysdb backend scan failed for [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-SYSDB_INIT ERROR : [chars] - [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-SYSDB_REG_ERR Sysdb Registration error : [chars] for [chars] [[chars]]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-WDSYSMON_EVENT_ERROR Received an invalid event from WDSysmon
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-WDSYSMON_REGISTER_ERROR [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-4-OOM_STATE_THROTTLE Received [chars] memory depletion warning, stop creating new igmp state
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-4-OOM_STATE_UNTHROTTLE Node memory back to normal, new igmp states will be created
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-4-OOR_WARN [chars]: [dec]
Explanation Maximum number of group accepted, either per interface or globally.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-6-ACCESS_GROUP_INFO ACL applied, removed [chars] from [chars]
Explanation ACL applied to interface on which denied groups join previosly.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-6-IPARMS_UPDATE_ERR Dropping iparms update: type [chars] for [chars] [[hex]]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV4_MCAST_CHKPT Messages
Error Message%ROUTING-IPV4_MCAST_CHKPT-3-ERR Failed to [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV4_MCAST_NETIO_DEBUG Messages
Error Message%ROUTING-IPV4_MCAST_NETIO_DEBUG-3-INIT_ERR [chars] [dec] [chars] [dec] [chars]
Explanation Internal error. Multicast NetIO debug library initilization failed
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MCAST_NETIO_DEBUG-6-TERM_ERR [chars] [dec] [chars] [dec] [chars]
Explanation Internal non-serious error. Mcast netio debug library termination failed
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV4_MFWD_HFR Messages
Error Message%ROUTING-IPV4_MFWD_HFR-3-BAG_REGISTRY Couldn't register bags : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD_HFR-3-EVENT_CONN_MGR Cannot open event connection manager: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD_HFR-3-EVENT_MGR Cannot create event manager: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD_HFR-3-EXIT Unexpected exit
Explanation Internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD_HFR-3-GEN_ERR [chars] failed : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD_HFR-3-REGISTER_EDM Couldn't register_edm : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD_HFR-5-SYSDB_INIT [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV4_MFWD Messages
Error Message%ROUTING-IPV4_MFWD-2-MFIB_RESET_FAIL [chars] : [chars]
Explanation Failed to clear all DBs after getting MFIB reset message. MFIB is no longer valid
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ADJ_CREATE [chars] [chars] : [chars]
Explanation Internal error: Cannot create the adjacency for a particular interface. Will retry for few times
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-AIB_FINT [chars]: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-AIB_INIT Failed to initialize AIB connection: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-AIB_MAP Failed to map AIB table: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-AIB_REGISTER Failed to register for AIB callbacks: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-AIB_ZERO_ALL [chars]: [chars]
Explanation We were not able to set all cached adjacencies to zero when we got ELIBBAD from AIB
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-BAG_REGISTRY Couldn't register bags : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-BIT_OWNERSHIP_VIOLATION multicast protocol state bit ownership violation
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-BOUNDARY_FAIL [chars] [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-DATAPATH_CONTROL im_caps_datapath_control error in function [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-DEBUG_ERR Error in attaching debug commands: [chars], file [chars], line [dec], function [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR [chars]
Explanation These are unexpected errors
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-EVENT_CONN_MGR Cannot open event connection manager: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-EVENT_MGR Cannot create event manager: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-EXIT Unexpected exit
Explanation Internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-FROM_MRIB_UPDATE MFIB couldn't process update from MRIB : [chars] - [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-FROM_MRIB_UPDATE_GLACIAL MFIB couldn't process update from MRIB : [chars] - [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-GEN_ERR [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-GEN_GLACIAL_ERR [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-GROUP_ERR [chars] [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-HA [chars]: [chars]
Explanation error while doing an HA operation (e.g. starting frequent restart monitor)
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-IARM_ERR [chars] [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-IDB_FAIL [chars] operation failed on [chars] in function [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-IDB_INIT Cannot intitialize IDB library : [chars]
Explanation Failed while initializing IDB library.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-IFH_ERR Failed to [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-IFH_INIT Failed to initialize IFH server : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-IIR_EVENT [chars] [chars] [chars]
Explanation Failure while processing an IIR event
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-IIR_INIT [chars] : [chars]
Explanation Failure while initializing or connecting to IIR
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-IM_CNTL_SVR_BIND_ERR Failed to initialize im control server connection: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-IM_DATA_SVR_BIND_ERR Failed to initialize im data server connection: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-IM_LOOKUP_FAILED IM lookup failed for [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-INSTALL [chars] : [chars]
Explanation Error while performing upgrade/downgrade/install operation
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-MAX_CONN_RETRY Cannot connect to [chars] using event conn Mgr after [dec] retries: [chars]
Explanation Reached the maximum number of retries to connect to server using event conn
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-MAX_DISABLE_RETRY Failed to disable multicast after [dec] retries: [chars]
Explanation Reached the maximum number of retries to disable multicast
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-MAX_ENABLE_RETRY Failed to enable multicast [dec] retries: [chars]
Explanation Reached the maximum number of retries to enable multicast and
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-MLIB_INIT [chars] [chars]
Explanation Failed while initializing multicast library.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-MRIB_INIT Failed to initialize MRIB connection [chars] call: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-NSF_INIT Failed to initialize Multicast NSF : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-PKT_INIT Failed to initialize packet connection: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-POST_MALLOC failed MRIB post buffer memory allocation
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-POST_TIMER couldn't create MFIB-MRIB post timer: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-RESTART_TIMER couldn't create a timer: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-RETRY_ERR [chars] [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-SHMWIN_ERR [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-SYSDB_ERROR SysDB operation [chars] failed: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-SYSDB_INIT Failed to initialize SysDB connection: [chars] - [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-TABLE_OPERATION_FAIL [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-TABLE_OPERATION_FAIL_GLACIAL [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-TO_MRIB_UPDATE MFIB couldn't post update to MRIB: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-TRANSACTION_PENDING_FLAG [chars] : [chars]
Explanation Failed to clear, set, or get transaction pending flag. That can only happen if the APIs to do that are called before shared mem window is opened, or if thereis a bug
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-TTL_CFG_FAIL [chars] [chars]: [chars]
Explanation Failed to apply a TTL threshold config. The operation will be retried.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-ADJ_CREATE_RETRY [chars] [chars] : [chars]. Retrying
Explanation Internal error: Cannot create the adjacency for a particular interface. Will retry for few times
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-AIB_UPDATE Failed to [chars] AIB for interface [chars] : [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-CLEAN_ALL_FAIL [chars] [chars]
Explanation Failure while doing all reource cleanup
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-INIT [chars] [chars]
Explanation Error ocured while enabling mcast
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-MRIB_INIT_RETRY Failed to initialize MRIB connection in [chars]. Retrying later: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-RETRY [chars]: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-TERMINATE [chars] [chars]
Explanation Error ocured while disabling mcast
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-CLEAN_ALL [chars] [chars]
Explanation Information regarding all resource cleanup
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-CONFIG_RETRY [chars] [chars]
Explanation One or more configs may have failed. We will retry them. This is a not a problem.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-IIR_RETRY [chars] [chars]
Explanation Applying one or more IIR notifications may have failed. We will retry them. This is a not a problem unless it keeps showing up continuously.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-IP_ADDR_RETRY [chars] [chars]
Explanation APplying one or more IP address configs may have failed. We will retry them. This is a not a problem unless it keeps showing up continuously.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-MCAST_DISABLED [chars] [chars]
Explanation Most likely mfwd restarted and while it was down mcast was disabled. The other possibility is that mfwd retsarted while disabling mcast. In either case, when mfwd comes up, it will find that mcast is already disabled. Hence it will log this message and exit normally
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-MFIB_RESET [chars] : [chars]
Explanation Got notification that the the MFIB has been reset. Will clear MFIB and restart
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-MRIB_UPDATE_RETRY [chars] [chars]
Explanation Processing one or more updates may have failed. We will retry them. This is a not a problem.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-ROUTE_UPDATE_FAIL [chars] Restarting to recover.
Explanation Was not able to commit at least one route after retrying for the maximum number of times. In this case, mfwd will restart in an attempt to recover. This is not an error. It just indicates that mfwd is restarting to recover from possible stale route problem.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-SHMWIN_MUTEX [chars] : [chars]
Explanation NetIO or Mfwd terminated while holding shared mem mutex. Recovery action will be taken
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-TABLE_PER_PREFIX Cannot [chars] per prefix accounting for table [chars]. [chars] [chars]
Explanation Error while enabling/disabling per route accounting in a table
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-TABLE_PER_PREFIX_GLACIAL Cannot [chars] per prefix accounting for table [chars]. [chars] [chars]
Explanation Error while enabling/disabling per route accounting in a table
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-UPGRADE_AFFECT_TRAFFIC [chars] [chars]
Explanation Most likely some one tried to upgrade/downgrade mfwd while we're not connected to NetIO. In this case, teh upgrade will wipe out all MFIB and traffic will be disrupted
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV4_MLIB_DEBUG Messages
Error Message%ROUTING-IPV4_MLIB_DEBUG-3-ERR [chars]
Explanation This is a catch all error message. It usually means an uncorrectible problem
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB_DEBUG-3-INIT_ERR [chars] [dec] [chars] [dec] [chars]
Explanation Internal error. MLIB debug library initilization failed
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB_DEBUG-6-TERM_ERR [chars] [dec] [chars] [dec] [chars]
Explanation Internal non-serious error. MLIB debug library termination failed
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV4_MLIB Messages
Error Message%ROUTING-IPV4_MLIB-3-ADJ_FAIL Adjacency [chars] operation failed in function [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-BAG_REGISTRY Couldn't register bags : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-BIT_OWNERSHIP_VIOLATION multicast protocol state bit ownership violation
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-DATAPATH_CONTROL im_caps_datapath_control error in function [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-DATAPATH_CONTROL im_caps_datapath_control error in function [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-DEBUG_ERR Error in attaching debug commands: [chars], file [chars], line [dec], function [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-DELETE_FAIL Delete Failed for ([chars] [chars]/[dec]) from [chars] table [chars]
Explanation Internal error. Deleting an entry from ingress or egress failed
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-EVENT_CONN_MGR Cannot open event connection manager: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-EVENT_CONN_MGR Cannot open event connection manager: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-EVENT_MGR Cannot create event manager: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-EVENT_MGR Cannot create event manager: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-EXIT Unexpected exit
Explanation Internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-FROM_MRIB_UPDATE MFIB couldn't read update ([chars],[chars]/[dec]) from MRIB: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-IM_CNTL_SVR_BIND_ERR Failed to initialize im control server connection: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-IM_DATA_SVR_BIND_ERR Failed to initialize im data server connection: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-IM_LOOKUP_FAILED IM lookup failed for [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-INTF_RTREE_ERROR Cannot create the interface adjacency rtree : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-MRIB_FETCH MRIB fetch failed: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-MRIB_INIT Failed to initialize MRIB connection in [chars] call: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-MRIB_OPCODE unexpected MRIB opcode: [hex]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-MRIB_UPDATE MRIB update failed: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-PKT_INIT Failed to initialize packet connection: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-POST_MALLOC failed MRIB post buffer memory allocation
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-POST_TIMER couldn't create MFIB-MRIB post timer: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-SHMWIN_ERR [chars] [chars]: [chars]
Explanation Error while doing shmwin operation
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-SHMWIN_ERR shared memory window failed: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-STATE_ERR [chars] [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-SYSDB_INIT Failed to initialize SysDB connection: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-TABLE_OPERATION_FAIL ipv4mc_table_operation failed for option : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-TO_MRIB_UPDATE MFIB couldn't post update to MRIB: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-TTL_ACTION_FAIL TTL [chars] action failed for entry [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-5-PER_PREFIX [chars] [chars]
Explanation Error while enabling/disabling per route accounting for a route
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-5-PER_PREFIX_GLACIAL [chars] [chars]
Explanation Error while enabling/disabling per route accounting for a route
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-5-TABLE_PER_PREFIX Cannot [chars] per prefix accounting for table [chars]. [chars] [chars]
Explanation Error while enabling/disabling per route accounting in a table
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV4_PIM Messages
Error Message%ROUTING-IPV4_PIM-2-REGISTER_API_ERR PIM Register api err [chars]: [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ACTIVE_GRANGE_ERR Invalid state - active grange in mrib [chars]/[dec] RP - [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-DEFINT_ERR Default interface error - [chars] [chars]
Explanation Problem configuring or setting the default interface.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-GEN_ERR Error - [chars] in [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-IDB_INIT [chars] in [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-IM_BATCH_STATE_ERR Invalid state for IM state registration batch on [chars]: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-IM_BULK_ERR Failed to [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-IM_ERR Interface Manager error - [chars] in [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-INIT_ERR [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-INTF_FWD_REF_ERR Interface Forward Reference Store error - [chars]: [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-LIST_ERR List error in [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-LTRACE_INIT ltrace_init failed for '[chars]': [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-MRIB_CONN_ERR MRIB connection error - [chars] in [chars] : [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-NET_ERR [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-NO_MEMORY for [chars] [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-OOR_COUNTER_ERR OOR [chars] counter has turned negative: [dec]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-PKT_ERR [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-PROTOCOL_ERR [chars] - [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-RP_INIT [chars] in [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-SOCK_ERR [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-SRC_UPDATE_ERR Error in [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-SYSDB_ERR [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-SYSMGR_ERR Sysmgr communication error - [chars]: [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-WDSYSMON_EVENT_ERROR Received an invalid event from WDSysmon
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-WDSYSMON_REGISTER_ERROR [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-CFG_WARNING [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-MYADDR_DB_ERR Failed operation: [chars] for [chars] - [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-OOM_STATE_THROTTLE Received [chars] memory depletion warning, stop creating new pim state
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-OOM_STATE_UNTHROTTLE Node memory back to normal, new pim states will be created
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-OOR_REGISTER_OK The number of PIM Register states ([unsigned int]) is now below the maximum. Normal PIM Register handling will resume.
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-OOR_REGISTER_WARN The maximum number of PIM Register states ([unsigned int]) has been reached. Register state creation will be throttled. Configure a higher maximum or take steps to reduce Register state.
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-OOR_ROUTES_OK The number of PIM routes ([unsigned int]) and route-interfaces ([unsigned int]) are now below the maximum. Normal PIM route handling will resume.
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-OOR_ROUTES_WARN The maximum number of PIM routes ([unsigned int]) or route-interfaces ([unsigned int]) has been reached. Route creation will be throttled. Configure a higher maximum or take steps to reduce multicast state.
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-RANGE_INIT [chars] in [chars] : [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-RPF_INTERFACE_UNSUPPORTED RIB returns an unsupported RPF interface [chars] for [chars], ignore rib information, set RPF interface to NULL
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-5-NBRCHG PIM neighbor [chars] [chars] on [chars] [chars]
Explanation PIM neighbor state change message.
Recommended Action No action is required.
IPV4MC_STATIC Messages
Error Message%ROUTING-IPV4MC_STATIC-3-CERR_V [dec] [chars] [chars]
Explanation Internal error. Cannot Registyer with CERR_V subsystem
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4MC_STATIC-3-CREATE_TIMER_LEAF [dec]: Cannot create timer leaf: [chars]
Explanation Internal error. Cannot create manageed timer leaf
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4MC_STATIC-3-DEBUG_INIT_ERR [chars] [dec] [chars] [dec] [chars]
Explanation Internal error. Static Mcast debug library initilization failed
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4MC_STATIC-3-EVENT_CONN_MGR [dec]: Cannot open event connection manager: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4MC_STATIC-3-EVENT_INIT_EVENT [dec]: Cannot Initialize sigevent structure: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4MC_STATIC-3-EVM_CREATE [dec]: Event Manager creation Failed: [chars]
Explanation Internal error. Failed while creating event manager
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4MC_STATIC-3-INIT_IDB [dec]: Cannot initialize IDB list: [chars]
Explanation Internal error. Cannot create initialize IDB list
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4MC_STATIC-3-INIT_TIMER [dec]: Cannot create managed timer: [chars]
Explanation Internal error. Cannot create manageed timer
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4MC_STATIC-3-INTF [dec]: Error [chars] [chars]
Explanation Internal error. Error while doing IM or IDB stuff
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4MC_STATIC-3-MRIB [dec]: [chars]: [chars]
Explanation Internal error. Error while doing MRIB API
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4MC_STATIC-3-ROUTE [dec]: [chars] ([chars],[chars]/[dec])
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4MC_STATIC-3-TIMER_ASYNC_CODE [dec]: Cannot obtain pulse code for the timer: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4MC_STATIC-3-TOPOLOGY_INIT [dec]: Cannot create static topology
Explanation Internal error. Cannot create manageed timer leaf
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV6_FIB Messages
Error Message%ROUTING-IPV6_FIB-2-RIBREJECT Rejecting RIB Update for [chars]/[dec] status [dec]
Explanation Rejected a route update from the RIB.
Recommended Action Try repopulating the missing route. If not recovered, it will lead to forwarding inconsistencies. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. *SUPPORT*
Error Message%ROUTING-IPV6_FIB-7-PFIFAIL PFI-IFH Server Error for [hex] status = ([dec])
Explanation Cannot talk to the PFI-IFH process
Recommended Action Informational message. PFI-IFH process does not have the information about the interface-handle at this very moment Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
ISIS Messages
Error Message%ROUTING-ISIS-3-BFD_SESSION_CREATE_FAIL Can't create BFD session over [chars] to [chars]: [chars] ([hex])
Explanation IS-IS failed to create a session with the BFD server. Creation will be reattempted on the next received IIH. Depending on the neighbor's support of BFD this may cause adjacencies to go down.
Recommended Action This failure may due to lack of resources. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. If the failure is not due to a lack of resources seek support. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-DBG_INIT_FAILED IS-IS failed to initialize its debug resources and will abort
Explanation IS-IS failed to initialize one of its debug services. The process cannot continue without its debug services and so will have aborted, but should have been restarted rapidly afterwards. This message will have been preceded by another one providing more precise details of the failure. The problem may be due to low memory resources and the detail of the preceding error message provides an indication of whether this is the case.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*
Error Message%ROUTING-ISIS-3-ERR_BAD_SOCKET_ADDR_LENGTH Bad socket address length ([unsigned int], should be [unsigned int] or [unsigned int]) in packet 0x[pointer]
Explanation A packet which IS-IS has received from its network socket contains a socket address with an invalid length. This is an internal error which indicates that the packet has been corrupted after being received by the local router but before being received by IS-IS. The problematic packet has been dropped. If this is an occassional problem then IS-IS should be able to continue operating normally when the packet is resent. If the message recurs, then IS-IS may start to operate incorrectly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..
Error Message%ROUTING-ISIS-3-ERR_BAG_ENCODE Failed to encode data for [chars] for external data manager (Reason: [chars])
Explanation A process has requested information through SysDB, probably as the result of executing a show command. An attempt to encode data for this has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_BAG_REGISTER Failed to register bag structures with bag server (Reason: [chars])
Explanation The process could not register the data structures used by IS-IS statistics and management agents.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_CLOCKTIME Error retrieving or setting the time of the [chars] clock: [chars] ([hex])
Explanation An unexpected error occurred whilst retrieving the time of a System Clock. This may be due to resource starvation or an internal programming error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_CONFIG_TO_TE Error during communication of [chars] information to TE processes: [chars]
Explanation IS-IS was unable to inform the TE processes of its configuration or basic operational state.
Recommended Action Restart the IS-IS process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_DLIST_ADD Failed to add an entry to an external data manager data list for [chars] (Reason: [chars])
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The attempt to add an item to an external data manager datalist has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_DLIST_CREATE Failed to create external data manager data list for [chars] (Reason: [chars])
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The creation of the datalist to be returned has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_DLIST_SET_MORE_FLAG Failed to set the 'more data' flag on a returned [chars] data list: error [hex] ([chars])
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The attempt to set the 'more data' flag to an external data manager datalist has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_EDM_FNS_INIT [chars] management function initialization failed: [hex], '[chars]'
Explanation The IS-IS process failed to initialize the handler functions for external data management. As a result, show and clear commands will not function.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_EDM_REGISTER [chars] SysDB registration failed: [hex], '[chars]'
Explanation The process could not register with SysDB for management of the data used by IS-IS statistics and management agents. As a result, show and clear commands will not function.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_GET_JOB_ID Failed system manager call to get IS-IS job_id: [hex], '[chars]'
Explanation IS-IS failed on a call to system manager to get its job_id. It's an internal fatal error. IS-IS process will abort.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..
Error Message%ROUTING-ISIS-3-ERR_GET_NODE_STATE Failed system manager call to get the node state information: [hex], '[chars]'
Explanation IS-IS failed on a call to system manager to get the node related state information. It's an internal fatal error. IS-IS process will abort.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..
Error Message%ROUTING-ISIS-3-ERR_GET_TUPLE Failed system manager call to retrieve the process tag name: [hex], '[chars]'
Explanation IS-IS failed on a call to system manager to retrieve its tag name during process initialization. It's an internal fatal error. IS-IS process will abort.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..
Error Message%ROUTING-ISIS-3-ERR_LIST_ADD Failed to add an entry to an external data manager list for [chars] (Reason: [chars])
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The attempt to add an item to an external data manager list has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_LIST_CREATE Failed to create external data manager list for [chars] (Reason: [chars])
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The creation of the list to be returned has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_LOCKING_FAIL Unexpected error '[chars]' trying to [chars] the [chars]
Explanation An unxpected error occurred whilst trying to lock or unlock an IS-IS resource. This implies an internal programming error.
Recommended Action Consider restarting the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_LTRACE_BUFFER Error [chars] trace buffer '[chars]': [chars] ([hex])
Explanation An unexpected error occurred whilst accessing a tracing buffer. This may be due to resource starvation or an internal programming error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_MEMPOOL_CREATE Failed to create the [chars]
Explanation IS-IS failed to create a memory pool. IS-IS cannot operate without this resource and will abort. The most likely cause is a low memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Restart IS-IS. *RECUR*
Error Message%ROUTING-ISIS-3-ERR_NODE_STATE_CHANGE Failed to register with system manager to get node state change notification: [hex], '[chars]'
Explanation IS-IS failed on a call to system manager to register to get node state change notification. It's an internal fatal error. IS-IS process will abort.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..
Error Message%ROUTING-ISIS-3-ERR_PAK_CLIENT_ACCESS Error [chars] a packet buffer (0x[pointer]): [chars]
Explanation IS-IS encountered an error whilst accessing a packet buffer. The relevant packet has been ignored. The message describes the nature of the error. If the problem is transient then IS-IS will recover. The error may be due to a low memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. *RECUR*. Consider restarting IS-IS.
Error Message%ROUTING-ISIS-3-ERR_PAK_CLIENT_CONN Error [chars] the managed connection to the packet server: [chars] ([dec])
Explanation IS-IS encountered an error whilst trying to set up a managed connection to the Packet Server. This is a serious error as IS-IS requires Packet I/O services to be able to form adjacencies, and the IS-IS process will shut itself down in response. This may be due to a low memory condition but is more likely to be a programming error. The error string and error code provide more information about the cause.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. *RECUR*.
Error Message%ROUTING-ISIS-3-ERR_PAK_CLIENT_GET_BUFFER Error obtaining a packet buffer of length [unsigned int]
Explanation IS-IS encountered an error whilst attempting to acquire a packet buffer to use to send a packet. The relevant packet has been dropped. The problem may be due to resource starvation. IS-IS will recover when sufficient resources become available.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. *RECUR*.
Error Message%ROUTING-ISIS-3-ERR_PROC_AVAILABLE Failed system manager call to indicate that IS-IS has completed initialization: [hex], '[chars]'
Explanation IS-IS failed on a call to system manager to indicate that it has completed all its initialization and is now completely online. It's an internal fatal error. IS-IS process will abort.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..
Error Message%ROUTING-ISIS-3-ERR_PROC_READY Failed system manager call to indicate that IS-IS is ready: [hex], '[chars]'
Explanation IS-IS failed on a call to system manager to indicate that it's ready to proceed. It's an internal fatal error. IS-IS process will abort.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..
Error Message%ROUTING-ISIS-3-ERR_RECV_BAD_TE_MSG Received [chars] in the [chars] message from TE
Explanation The process has received a TE message with invalid contents. As a result, the TE message is ignored and TE tunnel may not come up.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_RECV_PAK Error receiving packet: [chars]
Explanation An internal error has occurred receiving the packet. This is most likely due to some failure in a system service or a limited resource being exhausted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_RIB_BATCH_BUFFER Unexpected error [chars] batch of [chars] RIB updates ([dec])
Explanation IS-IS encountered an unexpected error whilst defining a batch of updates to be sent to the RIB. This is an internal programming error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_RIB_PATH Unexpected error installing a path to [chars] in the [chars] RIB ([dec])
Explanation IS-IS was unable to install a path to the specified network in the the specified RIB because the RIB rejected the request. This is an internal programming error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_SEND_PAK Error sending IS-IS packet: [chars]
Explanation The process encountered an error while sending the IS-IS packet.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_SYSDB_ACCESS Error [chars] [chars] SysDB item ([chars]): [hex], '[chars]'
Explanation An unexpected error occurred whilst accessing the specified SysDB item. This may be due to resource starvation or an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. *RECUR*. The IS-IS process must be restarted before it can function correctly.
Error Message%ROUTING-ISIS-3-ERR_SYSDB_CONNECT [chars] SysDB connection could not be established at the path [chars]: [hex], '[chars]'
Explanation IS-IS failed to bind to SysDB while opening a connection to it.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. The IS-IS process must be restarted before it can function correctly.
Error Message%ROUTING-ISIS-3-ERR_SYSDB_DATALIST Error [chars] SysDB datalist containing [chars]: [chars] ([hex])
Explanation An unexpected error occurred whilst listing the contents of a directory in SysDB. This may be due to resource starvation or an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. *RECUR*. The IS-IS process must be restarted before it can function correctly.
Error Message%ROUTING-ISIS-3-ERR_SYSDB_REG_NOTIFY Failed to register for SysDB notifications on path [chars] ([chars])
Explanation IS-IS failed to register for notification of changes on the displayed SysDB path.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. The IS-IS process must be restarted before it can function correctly.
Error Message%ROUTING-ISIS-3-ERR_SYSDB_REG_VERIFY Failed to [chars] ([chars])
Explanation IS-IS failed to register for verification of changes to its configuration data.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. The IS-IS process must be restarted before it can function correctly.
Error Message%ROUTING-ISIS-3-ERR_SYSDB_STRING_CODING Error [chars] a '[chars]' string: [hex], '[chars]'
Explanation IS-IS failed to encode or decode a string using the SysDB encoding. Aa result IS-IS will not be able to complete the operation it was performing which it encountered the error. The message describes the string which was being encoded or decoded and this should indicate the nature of the operation which was being performed.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*
Error Message%ROUTING-ISIS-3-ERR_TAG_NAME Error retrieving process tag name: [hex], '[chars]'
Explanation An IS-IS process failed to retrieve its process tag name during process initialization. This is a fatal error and the IS-IS process will abort.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..
Error Message%ROUTING-ISIS-3-ERR_THREAD_KEY_CREATE Error creating '[chars]' registry for thread specific value: [chars]
Explanation IS-IS failed to create a key to store thread specific values such as the name of a thread. This may be due to a low memory condition but is most likely to be an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. *RECUR*
Error Message%ROUTING-ISIS-3-ERR_THREAD_ONCE Error performing a once per thread lifetime operation to initialize [chars]: [chars]
Explanation IS-IS failed to initialize the specified resource. This is an internal programming error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..
Error Message%ROUTING-ISIS-3-ERR_THREAD_SET_SPECIFIC Error associating [chars] with thread: [chars]
Explanation IS-IS failed to associated the specified per-thread resource with the thread. This may be due to a low memory condition but is most likely to be an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. *RECUR*
Error Message%ROUTING-ISIS-3-ERR_VRFN_FNS_INIT [chars] verification function initialization failed: [hex], '[chars]'
Explanation The IS-IS process failed to initialize the handler functions for verification of changes to its configuration data.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. The IS-IS process must be restarted before it can function correctly.
Error Message%ROUTING-ISIS-3-EVENT_CONN_CREATE_FAIL Error creating '[chars]' connection: [chars]
Explanation IS-IS failed to create a connection to an essential service during initialization. This is an internal error. It requires a restart of the process for recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-EVQ_DEQUEUE_FAIL Failed to remove [chars] from the [chars] queue: [hex], '[chars]'
Explanation An unexpected error occurred whilst removing the specified object from the specified queue.
Recommended Action Consider restarting the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-EVQ_ENQUEUE_FAIL Failed to enqueue [chars] on the [chars] queue: [hex], '[chars]'
Explanation An unexpected error occurred while enqueueing the specified object on the specified queue.
Recommended Action This failure is most probably due to limited memory. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-3-EVQ_SIZE_FAIL Failed to retrieve the size of the [chars] queue: [hex], '[chars]'
Explanation An unexpected error occurred whilst retrieving the size of the specified queue. As a result IS-IS's internal state may be inconsistent. This indicates an internal programming error.
Recommended Action Consider restarting the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..
Error Message%ROUTING-ISIS-3-IM_CB_REG_FAIL Failed to register handler for IM [chars] events: [hex], '[chars]'
Explanation IS-IS failed to register a handler for IM events relating to the specified protocol. This may be due to a low-memory condition but may also be due to internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Consider restarting the IS-IS process. *RECUR*.
Error Message%ROUTING-ISIS-3-IM_CONN_TO_COID_FAIL Unexpected error retrieving connection ID from IMD connection context: [hex], '[chars]'
Explanation IS-IS failed to retrieve a connection ID from the IMD connection context. This may be due to a low-memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Consider restarting the IS-IS process. *RECUR*.
Error Message%ROUTING-ISIS-3-INTF_SET_ADD_FAIL Failed to add [chars] to the set of [chars]: [hex], '[chars]'
Explanation An unexpected error occurred whilst trying to add an interface to the specified collection of interfaces. This is most likely to be due to a low memory condition, but may be an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Consider restarting the IS-IS process. *RECUR*
Error Message%ROUTING-ISIS-3-IPV6_LAS Error [chars] IPv6 local address consumer service: [hex], '[chars]'
Explanation An unexpected error occurred whilst IS-IS was using the IPv6 Local Address Consumer Service.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-LSPIXARRMATCH LSPix entry [dec] mismatch with LSP [pointer], LSP [chars] is [dec], entry [dec]
Explanation LSPix entry ENTRY-INDEX mismatch with LSP LSP-ID, LSP (index or level) is LSP-INDEX|LSP-LEVEL, entry ENTRY-INDEX|ENTRY-LEVEL. An internal inconsistency has been detected. The LSP index array does not match the index/level recorded in the corresponding LSP.
Recommended Action Clear the LSP database via the appropriate clear command. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-PDU_INSUFFICIENT_SPACE Unable to [chars] due to insufficient space in outgoing PDU
Explanation The process was unable to add information to an outgoing PDU. This is most likely an MTU issue.
Recommended Action Check the MTUs for the interfaces over which IS-IS is running.
Error Message%ROUTING-ISIS-3-THREAD_CREATE Error starting [chars] thread: [dec]
Explanation IS-IS failed to create a thread essential to its operation. This is an internal error. It requires a restart of the process for recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-TIMESTAMP Operation '[chars]' failed during packet timestamping: [hex] ([chars])
Explanation An operation failed during timestamp processing.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-TRIGGER Operation '[chars]' failed during log trigger processing : [chars]
Explanation An operation failed during log trigger processing. This is not critical and IS-IS functionality should be unaffected.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-ADJ_FREE_INLIST Attempt to free adjacency still in the database
Explanation An internal error has occurred. This system attempted to deallocate the memory for an adjacency before removing the adjacency from the adjacency database.
Recommended Action Clear IS-IS adjacencies via the appropriate clear command. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-ADJCHANGE Adjacency to [chars] ([chars]) ([chars]) [chars], [chars]
Explanation Adjacency to SYSTEM-ID (INTERFACE-NAME) Up|Down, REASON. The adjacency to the system with SYSTEM-ID has gone up or down due to REASON.
Recommended Action No action is required.
Error Message%ROUTING-ISIS-4-AREALOST Too many IS-IS areas--cannot route to area [chars]
Explanation Too many IS-IS areas--cannot route to area AREA-ADDRESS. This system has exceeded the limit of three learned area addresses. The largest address AREA-ADDRESS has been dropped from the list of active areas.
Recommended Action Reduce the number of area addresses in the routing area.
Error Message%ROUTING-ISIS-4-BFD_BIND_FAIL Attempt to connect to the BFD server failed: [chars] ([hex])
Explanation IS-IS failed to connect to the BFD server. The connection will be retried.
Recommended Action This failure may be due to lack of resources. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration..
Error Message%ROUTING-ISIS-4-BFD_CREATE_FAIL Attempt to create [dec] BFD session[chars] failed: [chars] ([hex])
Explanation IS-IS failed to create one or more sessions with the BFD server. The connection to the server will be reset in an attempt to recover from the error.
Recommended Action This failure may due to lack of resources. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. If the failure is not due to a lack of resources seek support. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-BFD_DELETE_FAIL Attempt to delete [dec] BFD session[chars] failed: [chars] ([hex])
Explanation IS-IS failed to delete one or more sessions with the BFD server. The connection to the server will be reset in an attempt to recover from the error.
Recommended Action This failure may due to lack of resources. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. If the failure is not due to a lack of resources seek support. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-BFD_DELETE_UNCONFIG_FAIL Attempt to admin shutdown [unsigned int] BFD session[chars] as a result of deconfiguration failed: [chars] ([hex])
Explanation IS-IS failed to admin shutdown one or more sessions with the BFD server. The connection to the server will be reset in an attempt to recover from the error.
Recommended Action This failure may due to lack of resources. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. If the failure is not due to a lack of resources seek support. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-BFD_SESSION_NOT_FOUND Failed to locate BFD session over [chars] to [chars] for an adjacency.
Explanation IS-IS failed to locate a BFD session for a given adjacency. If necessary IS-IS will reconnect to the server to correct.
Recommended Action None.
Error Message%ROUTING-ISIS-4-BGP_CONVERGE_ERR Overload bit not sent due to failure to register for notification of BGP convergence.
Explanation IS-IS is configured to set the overload bit in its LSPs upon startup and to wait for BGP to converge before resetting the overload bit, but an error has occurred whilst registering for notification of BGP convergence. As a result, the overload bit will not have been set upon startup. This may be due to a low-memory condition but may also be due to internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. *RECUR*.
Error Message%ROUTING-ISIS-4-CERR_REG_FAIL [chars]
Explanation This system was unable to register the CERR DLL. This is probably due to a faulty installation.
Recommended Action Be sure the libisis_error.dll is properly installed.
Error Message%ROUTING-ISIS-4-CLNS_CLIENT_INIT Failed to initialize CLNS interface registery: [chars]
Explanation IS-IS failed to initialize its interface registration process wth CLNS It requires a restart of process for recovery.
Recommended Action Restart the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-DBG_REGISTER_FAILED Error registering for IS-IS debug events: [hex], '[chars]'
Explanation IS-IS failed to register with the debug module for printing messages.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-DUPSYSTEM Possible duplicate system ID [chars] detected
Explanation The router with the system ID SYSTEM-ID has transmitted too many LSPs in brief period of time, which could indicate constant LSP reflooding caused by a duplicate system ID.
Recommended Action Check the configuration of other routers in the area for duplicate IDs.
Error Message%ROUTING-ISIS-4-ERR_ACL Unexpected error whilst [chars] [chars] ACL [chars]: [hex], '[chars]'
Explanation IS-IS encountered the specified unexpected error whilst performing the specified operation on the specified access-list. As a result IS-IS's operation will not correctly reflect the contents of the ACL. This may be due to a low-memory condition but may also be due to internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Consider restarting the IS-IS process. *RECUR*.
Error Message%ROUTING-ISIS-4-ERR_ADVMASK Error adding IS-IS to advertising mask of [chars] ([chars]): [hex], '[chars]'
Explanation IS-IS failed to add itself to the advertising mask for the specified route and topology, that route corresponding to a connected route on an interface over which IS-IS is running. This means that any protocols which redistribute IS-IS into themselves will not receive the specified route. The problem is most likely to be caused by a failure by ipv4-io or ipv6-io to install the route at all, although it could also be due to low memory conditions.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*
Error Message%ROUTING-ISIS-4-ERR_BAD_CIRC_TYPE Bad circuit type ([dec]) from [chars]
Explanation Bad circuit type (CIRCUIT-TYPE) from SOURCE_IF. This system received an IS-IS hello with a header reporting an invalid circuit type of CIRCUIT-TYPE. This is the result of a mal-formed packet rather than a configuration error. The packet has been ignored.
Recommended Action Identify the source of the offending packet and correct it. If the message recurs 'debug isis packet-errors detail' may be used to provide a dump of the problematic PDU.
Error Message%ROUTING-ISIS-4-ERR_BAD_HDR_LENGTH The packet header length [unsigned int] is invalid for a(n) [chars], (should be [unsigned int]) from [chars]
Explanation The packet header length (HDRLEN) is invalid for a(n) PDUTYPE, (should be EXPECTED) from SOURCE_IF This system received a PDUTYPE packet from SOURCE_IF claiming a header length of ACTUAL, rather than EXPECTED. The packet has been ignored.
Recommended Action Identify the source of the offending packet and correct it. If the message recurs 'debug isis packet-errors detail' may be used to provide a dump of the problematic PDU.
Error Message%ROUTING-ISIS-4-ERR_BAD_ID_LENGTH Bad system ID length ([unsigned int], should be 0 or [unsigned int]) from [chars]
Explanation Bad system ID length (ID-LENGTH, should be 0 or EXPECTED-LENGTH) from SOURCE_IF. This system received a pdu reporting an invalid system ID length of ID-LENGTH. This system only accepts values of 0 and 6 (both indicate 6). The packet has been ignored.
Recommended Action Identify the source of the offending packet and correct it. If the message recurs 'debug isis packet-errors detail' may be used to provide a dump of the problematic PDU.
Error Message%ROUTING-ISIS-4-ERR_BAD_MAX_AREA_ADDR Bad max area addresses ([dec], should be 0 or [dec]) from [chars]
Explanation Bad max area addresses (MAX-AREA-ADDRESSES, should be 0 or EXPECTED-MAX) from SNPA (INTERFACE-NAME). This system received a pdu reporting an invalid number of configurable area addresses. This system only accepts values of 0 and 3 (both indicate 3). The packet has been ignored.
Recommended Action Identify the source of the offending packet and correct it. If the message recurs 'debug isis packet-errors detail' may be used to provide a dump of the problematic PDU.
Error Message%ROUTING-ISIS-4-ERR_BAD_PAK_LENGTH The length ([unsigned int]) reported in the packet buffer is greater than the maximum packet length that IS-IS can receive ([unsigned int])
Explanation IS-IS has received a packet which is larger than its internal buffers can handle. The packet has been ignored.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.. Consider reducing the relevant interface's MTU.
Error Message%ROUTING-ISIS-4-ERR_BAD_PDU_FORMAT [chars] received from [chars] contains a format error: [chars]
Explanation IS-IS has received a PDU containing a format error. This indicates that the system which built the PDU is not conforming to the protocol specification. In most cases this is the neighbor, but in the case of LSPs it is the system which generated the LSP. The message contains the type of the PDU, the interface it was received over (and, in the case of a LAN interface, the SNPA), and a description of the format error. IS-IS will not use any of the information contained in this PDU. In the case of an LSP, IS-IS will not flood the LSP to neighbors.
Recommended Action Identify the source of the offending packet and correct it. If the message recurs 'debug isis packet-errors detail' may be used to provide a dump of the problematic PDU.
Error Message%ROUTING-ISIS-4-ERR_BAD_PDU_LENGTH The length ([unsigned int]) reported in the [chars] header is greater than the packet length ([unsigned int]) from [chars]
Explanation The length (PDU_LENGTH) reported in the PDUTYPE header is greater than packet length (PKTLEN) from SOURCE_IF This system received an IS-IS packet that was LENGTH bytes long, which is shorter than the required header length for a PDUTYPE packet. The packet has been ignored.
Recommended Action Identify the source of the offending packet and correct it. If the message recurs 'debug isis packet-errors detail' may be used to provide a dump of the problematic PDU.
Error Message%ROUTING-ISIS-4-ERR_BAD_PDU_VERSION The PDU version reported in the IS-IS header is invalid ([unsigned int], should be [unsigned int]) from [chars]
Explanation The PDU version reported in the IS-IS header is invalid (VERSION, should be EXPECTED) from SNPA (INTERFACE-NAME) This system received a protocol packet bearing an invalid VERSION in the header. The router originating the packet is either placing the wrong protocol version number in the packet, or else it is running an incompatible version of the IS-IS protocol.
Recommended Action Identify the source of the offending packet and correct it. If the message recurs 'debug isis packet-errors detail' may be used to provide a dump of the problematic PDU.
Error Message%ROUTING-ISIS-4-ERR_BAD_VERSION Bad protocol version ([dec], should be [dec]) from [chars]
Explanation Bad protocol version (VERSION, should be EXPECTED-VERSION) from SOURCE_IF. This system received a pdu with an invalid protocol version of VERSION instead of EXPECTED-VERSION. The packet has been ignored.
Recommended Action Identify the source of the offending packet and correct it. If the message recurs 'debug isis packet-errors detail' may be used to provide a dump of the problematic PDU.
Error Message%ROUTING-ISIS-4-ERR_IP_MAXPATH_CHANGE Failed to change [chars] maximum parallel path setting to [unsigned int]. Previous value [unsigned int] still in use
Explanation IS-IS failed to change the maximum parallel path setting for the specified topology's local routing table. The previous setting will continue to be used. The most likely cause is a low memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Reapply the 'maximum parallel path' configuration or restart IS-IS. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-ERR_LSP_INPUT_Q_OVERFLOW LSP input queue overflow: [unsigned int] total drops; [unsigned int] LSP drops, [unsigned int] SNP drops
Explanation An incoming LSP or SNP pdu was dropped because the input queue was full
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-ERR_MEMPOOL_NOMEM Failed to allocate [unsigned int] bytes from '[chars]'
Explanation IS-IS failed to allocate memory from the specified pool.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-ERR_MIN_PDU_LENGTH The length ([unsigned int]) described in the [chars] header is smaller than the minimum ([unsigned int]) from [chars]
Explanation The length (PDU_LENGTH) described in the PDUTYPE header is smaller than the minimum (MINLEN) from SOURCE_IF This system received an IS-IS packet that was LENGTH bytes long, which is shorter than the required header length for a PDUTYPE packet. The packet has been ignored.
Recommended Action Identify the source of the offending packet and correct it. If the message recurs 'debug isis packet-errors detail' may be used to provide a dump of the problematic PDU.
Error Message%ROUTING-ISIS-4-ERR_MIN_PKT_LENGTH The length ([unsigned int]) of the [chars] received from [chars] is smaller than the minimum ([unsigned int])
Explanation The length (PKTLEN) of the PDUTYPE received from the interface SOURCE is smaller than the minimum (MINLEN) This system received an IS-IS packet that was LENGTH bytes long, which is shorter than the required header length for a PDUTYPE packet. The packet has been ignored.
Recommended Action Identify the source of the offending packet and correct it. If the message recurs 'debug isis packet-errors detail' may be used to provide a dump of the problematic PDU.
Error Message%ROUTING-ISIS-4-ERR_MSG_CHAN_GLOBAL Error changing a local message channel setting to [chars]: [chars] ([dec])
Explanation IS-IS failed to convert a local connection channel to a global connection channel. This could be the result of a problem with the channel.
Recommended Action Restart the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-ERR_MSG_GET_SCOID Error retrieving client's connection ID to the [chars] channel: [chars] ([dec])
Explanation IS-IS failed to retrieve its local connection ID for a client attached to the specified channel. This is an internal programming error.
Recommended Action Restart the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-ERR_MSG_REPLY Error replying to the client [chars]: [chars] ([dec])
Explanation IS-IS failed to reply to its client through message channel. This could be a result of channel down or resource allocation failure.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Restart the IS-IS process. *RECUR*
Error Message%ROUTING-ISIS-4-ERR_PCL Unexpected error whilst [chars]: [hex], '[chars]'
Explanation IS-IS encountered an unexpected error whilst performing the specified using the Route Policy client library. As a result information may be omitted from the local system's LSPs. This may be due to a low-memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Consider restarting the IS-IS process. *RECUR*.
Error Message%ROUTING-ISIS-4-ERR_RIB Unexpected error whilst [chars] the [chars] RIB: [hex], '[chars]'
Explanation IS-IS encountered an unexpected error whilst performing the specified RIB operation. This may be a resource starvation problem but is most likely to be an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Restart the IS-IS process. *RECUR*
Error Message%ROUTING-ISIS-4-ERR_RIB_BATCH_SEND Unexpected error sending a batch of [chars] RIB updates ([dec])
Explanation IS-IS encountered an unexpected error whilst sending a batch of RIB updates to the RIB. This may be a resource starvation problem, or a problem with IS-IS's connection to the RIB, or an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Restart the IS-IS process. *RECUR*
Error Message%ROUTING-ISIS-4-ERR_RIB_CONN_SETRETRY Error setting the RIB linear retry period: [hex] '[chars]'
Explanation IS-IS failed to set the linear retry period for connecting to the RIB. This error will not affect IS-IS operation but does indicate an unexpected result.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-ERR_RIB_LIB Unexpected error whilst [chars]: [hex], '[chars]'
Explanation IS-IS encountered an unexpected error whilst performing the specified operation using the RIB client library. This may be a resource starvation problem but is most likely to be an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Consider restarting the IS-IS process. *RECUR*
Error Message%ROUTING-ISIS-4-ERR_RIB_PATH_NOMEM Insufficient memory whilst installing a path to [chars] in the [chars] RIB
Explanation IS-IS was unable to install a path to the specified network in the RIB because the RIB encountered a low memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-ERR_ROUTE_MAP Unexpected error [chars] route map [chars] applied to the [chars] topology
Explanation IS-IS encountered an unexpected error whilst using the route map library. This may be due to a low memory condition. As a result information may be missing from the system's LSP.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Consider restarting the IS-IS process. *RECUR*.
Error Message%ROUTING-ISIS-4-ERR_SHOW_PROTO_REG Error registering show protocol information: [hex], '[chars]'
Explanation IS-IS failed to register for notification of changes on the displayed SysDB path. The error will not affect IS-IS operation but does indicate unexpected system behavior.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-ERR_SYSDB_DISCONNECT Error disconnecting [chars] SysDB connection: [hex], '[chars]'
Explanation IS-IS failed to disconnect from SysDB. The error will not affect IS-IS operation but does indicate that a programming error has occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-ERR_SYSDB_UNREG_NOTIFY Error unregistering for SysDB notification: [hex], '[chars]'
Explanation IS-IS failed to unregister for notification of changes on the displayed SysDB path. The error will not affect IS-IS operation but does indicate unexpected system behavior.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-ERR_THREAD_SET_NAME Error recording name of [chars] thread in registry: [chars]
Explanation IS-IS failed to store the name of specified thread in its registry. This is not a fatal error as the name is only used for debugging and error messages. The cause may be a low memory condition but is most likely to be an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. *RECUR*
Error Message%ROUTING-ISIS-4-ERR_WDSYSMON_MEM_STATE Unexpected error whilst [chars] for memory state changes: [chars] ([hex])
Explanation IS-IS encountered an error whilst registering or deregistering with WDSysMon for notifications of changes to the router's memory state. If the error occurs during registration (i.e. when the IS-IS process is initializing) then it will abort and the system may recover automatically when the IS-IS process is restarted. If the error occurs during deregistration (i.e. when the IS-IS process is shutting down) then it is harmless and may be ignored.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..
Error Message%ROUTING-ISIS-4-EVENT_BOOL_FAIL Error [chars] the '[chars]' trigger: [hex], '[chars]'
Explanation IS-IS encountered an unexpected error using one of the infrastructure libraries. This may be due to a low memory condition but is more likely to be a programming error. The error message should provide more information about the cause.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Consider restarting the IS-IS process. *RECUR*.
Error Message%ROUTING-ISIS-4-EVENT_CONN_ERROR_FAIL Error resetting '[chars]' connection: [chars]
Explanation After detecting an error with the connection to the specified service, IS-IS failed to reset that connection. This is an internal error. It requires a restart of the process for recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-EVENT_CONN_EVM_HANDLER_FAIL Error registering for data events on '[chars]' connection: [chars]
Explanation During initialization, IS-IS failed to register for input or output notifications for the specified service. This is an internal error. It requires a restart of the process for recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-EVENT_CONN_GET_FD_FAIL Error retrieving the Connection ID from the '[chars]' connection: [chars]
Explanation IS-IS failed to retrieve the file descriptor associated with the specified service. This is an internal error.
Recommended Action Consider restarting the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-EVENT_CONN_NOTIFY_FAIL Error registering for critical events on '[chars]' connection: [chars]
Explanation During initialization, IS-IS failed to register for essential notifications regarding the state of the connection for the specified service. This is an internal error. It requires a restart of the process for recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-EVENT_CONN_OPEN_FAIL Error opening '[chars]' connection: [chars]
Explanation IS-IS failed to open a connection to an essential service during initialization. This is an internal error. It requires a restart of the process for recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-EVM_ATT_FAIL Failed to register a handler for '[chars]' messages: [chars]
Explanation IS-IS failed to register a handler for the specified class of event. This is an initialization error and implies that IS-IS will not be able to operate correctly. The IS-IS process must be restarted in order to recover. The cause may be a resource starvation problem but is most likely to be an internal programming error. The error message should give more details.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Restart the IS-IS process. *RECUR*
Error Message%ROUTING-ISIS-4-EVM_CBACK_ATT_FAIL Failed to register a [chars] callback handler: [chars]
Explanation IS-IS failed to register a callback handler due to the error. This is an initialization error and implies that the function in IS-IS will not be able to operate correctly. The IS-IS process must be restarted in order to recover.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Restart the IS-IS process. *RECUR*
Error Message%ROUTING-ISIS-4-EVM_CRE_FAIL Failed to create [chars] Event Manager: [chars]
Explanation IS-IS failed to create an Event Manager to receive events in the specified thread. This is most likely to be caused by a resource starvation problem, but may also be due to an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. *RECUR*.
Error Message%ROUTING-ISIS-4-EVM_SEND_FAIL Failed to send '[chars]' to '[chars]': [chars]
Explanation IS-IS failed to send the specified message. The cause may be a resource starvation problem but is most likely to be an internal programming error. The error message should give more details.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Restart the IS-IS process. *RECUR*
Error Message%ROUTING-ISIS-4-EVQ_CRE_FAIL Failed to create the [chars] event queue: [hex], '[chars]'
Explanation An unexpected error occured whilst creating an event queue during process initialization. This may be a system resource problem. As a result IS-IS will be unable to operate correctly.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. *RECUR*
Error Message%ROUTING-ISIS-4-EXTRA_AREA_ADDRESSES Area address TLV length [dec] contains more than ISIS_MAX_AREA_ADDRESSES from [chars] ([chars]).
Explanation Area address TLV length TLV_LENGTH contains more than ISIS_MAX_AREA_ADDRESSES from SNPA_STRING (INTERFACE_NAME). This system recieved a hello or LSP containing more than the maximum number of area addresses. The additional addresses have been ignored.
Recommended Action Identify the source of the offending packet and correct it.
Error Message%ROUTING-ISIS-4-IIH_TOO_MANY_IF_ADDRESSES [chars] has more [chars] interface addresses than can fit into a single TLV (255 bytes). Outgoing IIHs can only include the first [unsigned int] addresses.
Explanation The specified interface has more addresses than can be fitted into a single TLV (255 bytes). RFC 1195 specifies that each IIH may contain at most one IPv4 Interface Address TLV, i.e. 63 IPv4 addresses. Thus if there are more than 63 IPv4 addresses configured on the interface then only 63 addresses are included in the IIH. If the interface has a primary address it is always included first. The secondary addresses are added in their natural numerical order until there is no more space. If there is an IS on the LAN which does not share a subnet with any of the advertised addresses then it will not be able to form an adjacency with this IS. This problem should not apply to IPv6 as each interface should have a single link local address.
Recommended Action Reduce the number of addresses configured on the interface so that they can all fit within a single TLV.
Error Message%ROUTING-ISIS-4-IM_ATTR_INIT Error initializing the IM attribute library: [hex] '[chars]''
Explanation IS-IS failed to initialize the IM attribute library. This error will prevent IS-IS from normal operations.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Consider restarting the IS-IS process. *RECUR*.
Error Message%ROUTING-ISIS-4-IM_CAPS_UNKNOWN IM notification received for an unknown and unexpected capsulation number: [unsigned int]
Explanation IS-IS has received an IM message referring to a capsulation number that IS-IS does not recognized and is not able to handle. This is an internal programming error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-IM_CB_NAME_TRUNC Interface Manager context name '[chars]' length exceeds string length limit of [dec]; truncated to '[chars]'
Explanation The length of the context string used to register for Interface Manager callbacks exceeded internal limits and was truncated. If truncation results in registration contexts no longer being unique, this could cause problems with event registrations.
Recommended Action This should not happen. The condition represents an internal error.
Error Message%ROUTING-ISIS-4-IM_INTF_REG_FAIL Error registering for [chars] [chars] changes on interface [chars]: [hex], '[chars]'
Explanation IS-IS failed to register for notification of the specified changes on the specified interface and protocol. This may be an internal programming error, but is most likely to be a resource starvation problem.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Consider disabling and reenabling the interface within IS-IS configuration, or restarting the IS-IS process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..
Error Message%ROUTING-ISIS-4-INTF_ADDR_CHG_REG Error during registration for interface IP address changes: [chars]
Explanation IS-IS failed to register for notification of interface IP address changes. This is may be due to lack of resources or an internal error (the error message will indicate which). It requires a restart of the process for recovery.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-INTF_ATTR_FAIL Failure while [chars] on [chars]: [hex] '[chars]''
Explanation A call to the IM attribute library failed. This can be caused by faulty hardware, or it may indicate an interface resource is currently unavailable. Recovery may require a restart of the IS-IS process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_CKTNUM_ALLOC_FAIL Failed to allocate circuit ID to interface [chars]: all [dec] IDs already in use
Explanation IS-IS failed to allocate a circuit ID to the specified LAN interface.
Recommended Action Reduce the number of LAN interfaces over which IS-IS is running.
Error Message%ROUTING-ISIS-4-INTF_CLNS_MAC_ADDR_NOTIFY Failed to notify CLNS of a MAC address change on interface [chars]: [chars]
Explanation IS-IS failed to notify the CLNS protocol stack of MAC address changes to the specified interface. It requires a restart of process for recovery.
Recommended Action Restart the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_CLNS_NOTIFY Failed to add the CLNS stack on interface [chars]: [chars]
Explanation IS-IS failed to add the CLNS protocol stack on the specified interface. It requires a restart of process for recovery.
Recommended Action Restart the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_CLNS_REMOVE_CAP Failed to remove the CLNS stack on interface [chars]: [chars]
Explanation IS-IS failed to remove the CLNS protocol stack on the specified interface.
Recommended Action None.
Error Message%ROUTING-ISIS-4-INTF_FIND_FAIL Failed to lookup Interface Handle for interface [chars]: [hex] '[chars]'
Explanation An unexpected error occurred looking up an interface handle from an interface name. This may be due to a low memory condition but is most likely to be an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. *RECUR*
Error Message%ROUTING-ISIS-4-INTF_FWS_INIT Error during initialization of forward-referenced interface store: [chars]
Explanation IS-IS failed to initialize its storage for forward-referenced interfaces. This is may be due to lack of resources or an internal error (the error message will indicate which). It requires a restart of the process for recovery.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-INTF_INACTIVE_AF Unexpected [chars] [chars] notification on [chars]
Explanation The specified event was unexpected because the address family is not active on that interface. The operation of IS-IS is not affected by this message and it may safely be ignored. The message is due to an internal programming error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..
Error Message%ROUTING-ISIS-4-INTF_LAS_FAIL Failed [chars] [chars] link local addresses on [chars]: [hex], '[chars]'
Explanation An unexpected error occurred whilst accessing the link-local address details for the specified interface. As a result IS-IS will not be able to use the specified address-family on the specified interface. This could be due to a low memory condition or an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Consider restarting the IS-IS process. *RECUR*
Error Message%ROUTING-ISIS-4-INTF_MAC_SIZE_ERR Incorrect MAC address size for [chars] (returned: [dec], expected: [dec])
Explanation The MAC address size returned for the specified interface does not match the expected size (6 bytes). This can be caused by a faulty hardware.
Recommended Action Restart the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_MCAST_JOIN_FAIL Error joining [chars] multicast group on [chars]: [chars]
Explanation IS-IS was unable to join the specified multicast group on the specified interface.
Recommended Action Restart the affected interface and, if the problem recurs, the IS-IS process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_MCAST_LEAVE_FAIL Error leaving [chars] multicast group on [chars]: [chars]
Explanation IS-IS encountered an error while leaving the specified multicast group on the specified interface.
Recommended Action Restart the affected interface. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_MCAST_SIZE_ERR The multicast address is too large for [chars] (supplied: [dec], maximum: [dec])
Explanation The multicast address requested for the specified interface is larger than the maximum permissible size. This requires restarting the IS-IS process.
Recommended Action Restart the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_MTU_TOO_SMALL CLNS MTU value of [unsigned int] on [chars] is too small. Minimum acceptable value is [unsigned int]
Explanation The MTU for CLNS on the specified interface is too small to allow IS-IS to send packets over that interface. This may be due to a configuration error or an internal error.
Recommended Action Check any MTU configuration for the interface to ensure that this is not a configuration error. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_NAME_FAIL Failed to lookup an interface name from its handle ([hex]): [hex], '[chars]'
Explanation An unexpected error occurred looking up an interface's name from it's handle. The error code should provide an indication of what the problem is. The most likely explanation is that the interface with the specified handle no longer exists although the message may be caused by low memory conditions or an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. *RECUR*
Error Message%ROUTING-ISIS-4-INTF_NSF_MEDIA_MISMATCH Media class mismatch between checkpoint table ([chars]) and reality ([chars]) on interface [chars]
Explanation IS-IS has detected a mismatch between the media class (i.e. Point to Point vs. LAN) of an interface as determined by IS-IS's checkpoint state and IM. As a result the interface will not participate in the NSF restart. This is an internal programming error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_STORE_FAIL Error [chars] [chars] [chars] internal [chars] store: [hex], [chars]
Explanation IS-IS was unable to perform the specified operation on the specified interface. This is most likely to be a resource starvation problem, but may be an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Consider restarting the IS-IS process. *RECUR*
Error Message%ROUTING-ISIS-4-INTF_UNKNOWN_MEDIA Unknown or unsupported interface media type ([chars]) on [chars]
Explanation This interface media is not supported by IS-IS. An IS-IS process restart is required for recovery.
Recommended Action Check the interface media name in the configuration and restart the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-IP_ARM_ADDR_INFO_FAIL Failed to [chars] for [chars] address information: [hex], '[chars]'
Explanation IS-IS has encountered an error whilst manipulating a set of interface IP addresses. This may be a resource starvation problem or an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. *RECUR*.
Error Message%ROUTING-ISIS-4-ITEMSIZE add_item_entry called with size [dec]: errant entry was not added to the LSP
Explanation add_item_entry called with size SIZE. An internal error occurred while this system was trying to construct its LSPs. The errant entry was not added to the LSP.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-LSPCKSUM Bad L[dec] LSP [chars] checksum [hex] received on [chars], length [dec], should be [hex], bad count [dec]
Explanation Bad L-# LSP LSP-ID checksum ACTUAL-CKSUM received on INTERFACE-NAME, length PDU-LENGTH should be EXPECTED-CKSUM, bad count CKSUM-ERROR-COUNT. This system received a level L-# LSP with a wrong checksum. If the IS-IS configuration option 'isis-ignore-cksum-errors' is set, the packet has been ignored. Otherwise it has been handled according to the specification.
Recommended Action No action is required.
Error Message%ROUTING-ISIS-4-LSPDB_CORRUPT L[unsigned int] LSP database checksum verification failed for LSP [chars]. IS-IS will restart itself
Explanation A corrupt LSP was found during a periodic check of the sanity of the specified level's LSP database. When it encounters this condition the IS-IS process restarts itself to recover.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-LSPFULL L[unsigned int] LSP filled to capacity, dropping routes
Explanation L-LEVEL LSP filled to capacity, dropping routes. This system cannot originate any more routes or adjacencies because it cannot build any more LSP fragments in which to advertise them.
Recommended Action This is usually caused by a misconfiguration, such as redistributing a large number of routes into IS-IS. Reduce the number of routes being redistributed into IS-IS to correct the problem.
Error Message%ROUTING-ISIS-4-LSPIX_ENTRY_NULL Encountered null LSPix entry [dec] while [chars]. This should never happen.
Explanation LSPix entry ENTRY-INDEX, is NULL. This should never happen. An internal inconsistency has been detected. The LSP index entry has a null pointer.
Recommended Action Clear the LSP database via the appropriate clear command. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-LSPIXARRNULL LSPix entry [dec] should be null, is [pointer]
Explanation LSPix entry SLOT-NUM should be null, is VALUE. An internal inconsistency has been detected. The LSP index array slot 0 is reserved or has not been used and should be NULL. Instead it has the value VALUE.
Recommended Action Clear the LSP database via the appropriate clear command. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-LSPTOOBIG L[dec] LSP [chars] size [dec] bigger than interface [chars] MTU [dec], LSP dropped
Explanation L-LEVEL LSP LSP-ID size LSP-LENGTH bigger than interface INTERFACE-NAME MTU INTERFACE-MTR, LSP dropped. This system was unable to flood an LSP out INTERFACE-NAME because the interface MTU was too small. The LSP has not been transmitted on the interface.
Recommended Action Configure the routing area and the interfaces with a consistent MTU.
Error Message%ROUTING-ISIS-4-MAX_REDIST_PREFIXES Topology [chars] level [unsigned int] is [chars]exceeding the maximum number of redistributed prefixes
Explanation This configuration is redistibuting more than the allowable number of prefixes into an IS-IS topology. IS-IS will not advertise some of these routes. This is to prevent inadvertant redistribution of the Internet via IS-IS.
Recommended Action Consider reconfiguring route redistribution into the IS-IS process. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration..
Error Message%ROUTING-ISIS-4-MEM_ALLOC_FAIL Failed to allocate [unsigned int] bytes for '[chars]'
Explanation The process failed to allocate memory for the specified resource. This could be because the IS-IS topology is too large for the memory installed in the router.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-MGD_TIMER_FAIL Error [chars] the [chars] [chars] timer: [chars]
Explanation IS-IS encountered an unexpected error using the Managed Timer library. This is most likely to be due to a low memory condition but may also be an internal programming error. The error message should provide more information about the cause.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Consider restarting the IS-IS process. *RECUR*.
Error Message%ROUTING-ISIS-4-NSF_CHKPT_ACCESS_FAIL Failed to [chars] checkpoint record(s) [chars] [chars] table: [hex], '[chars]'
Explanation An unexpected error occurred whilst IS-IS was accessing entries in the specified checkpoint table. If this error occurs during an NSF Cisco restart then that NSF restart may be aborted in favour of a traditional restart. If this error occurs during normal operation then the relevant checkpoint table may not be correct, and a subsequent NSF restart may not succeed. If however the error does not recur then the checkpoint tables should synchronize. The error may be caused by a low memory condition or through programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. *RECUR*.
Error Message%ROUTING-ISIS-4-NSF_CHKPT_INIT NSF checkpoint init failure, [hex], '[chars]'
Explanation The IS-IS process failed to initialize the checkpoint service for the specified error reason.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-NSF_CHKPT_TABLE_FAIL Failed to [chars] [chars] checkpoint table: [hex], '[chars]'
Explanation An unexpected error occurred whilst IS-IS was accessing the specified checkpoint table. If this error occurs during an NSF Cisco restart then that NSF restart may be aborted in favour of a traditional restart. If this error occurs during normal operation then the relevant checkpoint table may not be correct, and a subsequent NSF restart may not succeed. The error may be caused by a low memory condition or through programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. *RECUR*.
Error Message%ROUTING-ISIS-4-NSF_CREATE_FAIL Failed to create L[unsigned int] NSF adjacency to [chars] ([chars]) ([chars])
Explanation TBD.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-NULL_IDB_LOOKUP_FAILURE Error in looking up the Null interface
Explanation The process encountered an error while looking up the Null interface data structure and the summary route was not installed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-OSI_SOKT_FAIL Socket operation '[chars]' failed: [chars]
Explanation Failed to perform a socket operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-REDIST_FAIL Error [chars] for redistribution of routes from [chars] [chars] into IS-IS
Explanation The RIB returned an unexpected error when IS-IS attempted to (de)register for the redistribution of routes in the specified topology and owned by the specified protocol. If this is a registration error then routes from the specified protocol may not be advertised in IS-IS's system LSPs. If this is a deregistration error then IS-IS may receive unnecessary redistribution updates from the RIB but the system LSPs will be correctly generated. The problem may be caused by a low memory condition but is most likely to be an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Consider restarting the IS-IS and/or the RIB processes. *RECUR*.
Error Message%ROUTING-ISIS-4-RESOURCE_ALLOC_FAIL Failed to allocate resources for '[chars]'
Explanation The process failed to allocate memory for the specified resource. This could be because the IS-IS topology is too large for the memory installed in the router.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-SEQNUM_WRAP Sequence number wrapped in LSP [chars].
Explanation An LSP originated by this system has had its sequence number wrap around to 0. The IS-IS specification states that this system should shutdown for 20 minutes waiting for the LSP to age out before resuming routing.
Recommended Action This condition can only occur if a network has been operational for several years, or if a network has been misconfigured for a long time. Disable the IS-IS routing process for max-lsp-lifetime and then restart it to clear the problem. Alternative approaches include changing the SYSTEM-ID or, if this occurred with a pseudo-node LSP, lowering the priority of the interface.
Error Message%ROUTING-ISIS-4-SETSOCKOPT_FAIL Error setting the value of the '[chars]' IS-IS network socket option to '[chars]' (length [unsigned int]): [chars]
Explanation IS-IS encountered an error whilst configuring the socket it uses for network I/O. As a result the socket is unuseable and IS-IS cannot perform I/O. IS-IS will attempt to recover by closing the current socket and schedule an attempt to reconnect.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.. Consider restarting the IS-IS process.
Error Message%ROUTING-ISIS-4-SHOW_NOMEM Internal memory allocation failure, display incomplete
Explanation The requested display output may be incomplete due to an internal memory allocation problem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-SHUTDOWN Process is shutting down ([chars]): [chars]
Explanation IS-IS has encountered a problem which means that is no longer able to continue and so it is shutting down. The message includes a brief description of the problem but will also have been preceded by another message providing a more detailed description of the problem. There are several types of reason why IS-IS may have to shutdown which include a fatal error during process initialization, a fatal problem with a critical service during normal operation, and a roll-over of one of the local system's LSP's sequence numbers. The message also describes whether or not IS-IS has automatically been restarted.
Recommended Action Follow the instructions associated with the preceding message. If an automatic restart has been scheduled, then IS-IS may recover automatically. If a manual restart is required, then 'process start isis' is required to recover.
Error Message%ROUTING-ISIS-4-TENT_NEGCOUNT TENT count negative
Explanation An internal error has occurred during the shortest path calculation. An attempt was made to decrement the size of the tentative queue to -1. The size remained 0.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-THREAD_DESTROY Error destroying [chars] thread: [dec]
Explanation IS-IS failed to destroy a thread. This is an internal error. If the error occurred whilst unconfiguring IS-IS then it may be necessary to forcefully terminate the IS-IS process. If the error occurred during normal operation then it may be necessary to restart the IS-IS process to recover.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-TIMESTAMP_FAIL Error recording a timestamp ([dec])
Explanation An unexpected error occurred whilst recording a timestamp. This implies an internal programming error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-UNKNOWN_ADDRESS_FAMILY Unknown address family [unsigned int]
Explanation IS-IS has encountered an unrecognized address family ID. This is an internal programming error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..
Error Message%ROUTING-ISIS-4-WD_METRIC_NOT_CONF In the topology [chars] [chars] has a wide metric of [unsigned int] but level L[unsigned int] is configured to generate narrow metrics. Maximum narrow value [unsigned int] is used instead
Explanation The specified interface and topology has been configured with a metric value that requires metric-style wide to be configured for the relevant level.
Recommended Action Configure metric-style wide for the topology and area.
Error Message%ROUTING-ISIS-4-ZEROHOLDTIME IIH zero holdtime from [chars]
Explanation IS-IS has received an IIH containing a zero holdtime from a neighbor with which no adjacency currently exists. The IIH has been discarded. The message indicates the interface and, in the case of a LAN interface, the SNPA from which the IIH was received.
Recommended Action No action is required.
Error Message%ROUTING-ISIS-5-AUTH_FAILURE_DROP Dropped [chars] from [chars] due to [chars]
Explanation The process encountered an error when authenticating an incoming PDU and dropped the PDU. This may be due to misconfiguration on the local or remote system.
Recommended Action Check the password configuration on the local and remote systems.
Error Message%ROUTING-ISIS-6-ADJNSF [chars] L[unsigned int]: Neighbor [chars] [chars]
Explanation The adjacency on the INTERFACE-NAME and LEVEL with the system SYSTEM-ID STARTED responding or STOPPED responding during the NSF-restart of the SYSTEM-ID.
Recommended Action No action is required.
Error Message%ROUTING-ISIS-6-ERR_DUPID Duplicate System ID [chars] already used by [chars] detected in IIH received on [chars]
Explanation IS-IS has received an IIH from a router claiming to have the same System ID as either the local system or another station on a LAN interface. The message indicates the interface and, in the case of a LAN interface, the SNPA from which the IIH was received. It also indicates whether we ourselves use this system ID, or the SNPA of the other station using the system ID.
Recommended Action Duplicate system IDs are usually the result of misconfiguration or a bridging loop in the network. Configure each router with a unique system ID, and ensure that there are no bridging loops in the network.
Error Message%ROUTING-ISIS-6-EVENT_CONN_DESTROY_FAIL Error destroying '[chars]' connection: [chars]
Explanation During process termination IS-IS failed to destroy a connection to a service provided by another process. This is an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-6-EVENT_ERR Event handler error [dec]
Explanation Event handler error ERRNO. This system encountered an error ERRNO trying to get an event from the event handler.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-6-EVQ_DESTROY_FAIL Failed to destroy the [chars] event queue: [hex], '[chars]'
Explanation An unexpected error occured whilst destroying an event queue. This is an internal programming error, but will not affect protocol operation as it occurred whilst IS-IS was destroying resources which are no longer required.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..
Error Message%ROUTING-ISIS-6-FAIL_ADJADD Failed to create adjacency for [chars] ([chars]): [chars]
Explanation Failed to create adjacency to the displayed IS via the displayed interface for the reason specified.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-6-IIH_IF_ADDRESS IIH received from [chars] contains [chars] [chars] interface address: [chars]
Explanation IS-IS received an IIH from the specified source containing an invalid and potentially unusable interface address for the specified address family. The message contains details of why the interface address is invalid. The message implies that the router sending the bad IIH is either misconfigured or is not conforming to the IS-IS specification. If the message describes the address as unusable, then IS-IS is not able to use the adjacency as a next hop for the specified address family. Otherwise IS-IS will still attempt to use the adjacency as a next hop.
Recommended Action Using the contents of the error message as a guide, check the configuration of the router sourcing the IIH or contact the router's vendor.
Error Message%ROUTING-ISIS-6-INFO_STARTUP_ABORTED [chars] controlled start aborted. Reason: [chars]
Explanation Startup state-machine controlled startup aborted for the specified reason. Some of the reasons indicate an internal software error, or the failure of anther software service. Other reasons are due to configuration or other operational problems.
Recommended Action If the indicated reason can be corrected with configuration changes, then do so; otherwise, Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-6-INFO_STARTUP_FINISH [chars] controlled start completed
Explanation Startup state-machine controlled startup process ends here.
Recommended Action None.
Error Message%ROUTING-ISIS-6-INFO_STARTUP_FORCED_COLD Resorting to cold start: [chars].
Explanation The startup state-machine has determined that a cold (re)start must be performed regardless of current NSF configuration for the reason specified.
Recommended Action None.
Error Message%ROUTING-ISIS-6-INFO_STARTUP_START [chars] controlled start beginning
Explanation Startup state-machine controlled startup process begins here.
Recommended Action None.
Error Message%ROUTING-ISIS-6-NO_INPUTBUF Unable to allocate input buffer
Explanation This system failed to allocate an input buffer because there was insufficient memory to do so.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-6-SPF_NO_SYSTEM_LSP L[unsigned int] Database does not contain our own lsp; unable to run SPF
Explanation The SPF algorithm requires that our own LSP is in the database, otherwise it returns an empty result.
Recommended Action Clear the LSP database via the appropriate clear command. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-7-ERR_CREATEMQ Error in creating message queue to MPLS
Explanation The process failed to create a message queue to communicate with MPLS.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-7-ERR_MSG Error in reading message: [chars]
Explanation The process failed to read the message.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-7-ERR_MSGLEN Error in reading message length: [chars]
Explanation The process failed to read the message length.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-7-ERR_RCV_PAKTYPE Invalid IS-IS packet type [unsigned int] received on [chars] ([chars] code)
Explanation An invalid packet was received on the specified interface (and, in the case of a LAN interface, SNPA). The packet is invalid because its type code is either unrecognized or inappropriate (e.g. a point to point IIH on a LAN interface). The packet has been ignored.
Recommended Action No action is required.
Error Message%ROUTING-ISIS-7-ERR_RECV_TE_MSG Received an invalid length TE message for [chars]: expected ([unsigned int]), received ([unsigned int])
Explanation The process has received an invalid length TE message. As a result, the TE message is ignored and TE tunnel may not come up.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-7-ERR_SEND_TE_MSG Failed to send a [chars] message to TE
Explanation The process encountered an error while sending message to TE.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
LDP Messages
Error Message%ROUTING-LDP-2-DEBUG_REG_ERR Debug registration failed: [chars]
Explanation Unable to initialize debugging flags. Debug commands will not function.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-2-INIT_ERR Failed to initialize '[chars]'. Process now terminating
Explanation Initialization of a LDP subsystem failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-2-INIT_RC_ERR Failed to initialize '[chars]': [chars]. Process now terminating
Explanation Initialization of a LDP subsystem failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-2-LSD_BIND_ERR Failed to connect to LSD after [dec] attempts
Explanation LDP encountered some problem while trying to connect with LSD server after several attempts.
Recommended Action Make sure that LSD is running.
Error Message%ROUTING-LDP-2-LSD_REG_ERR LSD application registration failed: [chars]
Explanation LDP encountered a problem while trying to register with LSD server.
Recommended Action Make sure that LSD is running and LDP is connected to it.
Error Message%ROUTING-LDP-2-NO_MEM No memory for '[chars]'
Explanation The requested operation failed due to low memory condition.
Recommended Action This indicates a low memory condition. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-LDP-2-SHUTDOWN LDP process is shutting down due to '[chars]' memory state.
Explanation LDP process exiting due to unknown/critical node memory state.
Recommended Action Start 'mpls_ldp' process after memory state goes normal.
Error Message%ROUTING-LDP-2-TDP_START_ERR LDP control module start failed. Process now terminating.
Explanation Failed to start LDP control module successfully.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-2-THREAD_CREATE_ERR Error starting '[chars]' thread: [chars]. Process restarting
Explanation LDP failed to create a thread essential to its operation. This is an internal error. An automatic restart of the LDP process is suggested to attempt recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-3-BACKEND_ERR Backend scan failed for '[chars]': [chars]
Explanation LDP failed backend scan for some tuple path.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-3-CHKPT_ERR Failed to read checkpointed data in '[chars]'. Resetting checkpointed data and rewrites.
Explanation The checkpointed data is corrupt.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-3-DEBUG_INIT_ERR Debug event initialize failed for event#[dec]: [chars]
Explanation Unable to initialize a debug flag
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-3-INTERNAL_ERR Internal error: [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-3-LSD_APPTIME_ERR LSD application recovery time API failed: [chars]
Explanation LDP encountered some problem while trying to set LDP recovery time with LSD server.
Recommended Action Make sure that LSD is running and LDP is connected/registered with it.
Error Message%ROUTING-LDP-3-LSD_BULKOP_ERR LSD bulking API failed in '[chars]': [chars]
Explanation LDP encountered a problem while trying to perform some bulk operation for the LSD server.
Recommended Action Make sure that LSD is running and LDP is connected/registered with it.
Error Message%ROUTING-LDP-3-LSD_BULKOP_ERR_STR [chars]
Explanation LDP encountered a problem while trying to perform some bulk operations for the LSD server.
Recommended Action Make sure that LSD is running and LDP is connected/registered with it.
Error Message%ROUTING-LDP-3-LSD_BULKOP_REPLY_ERR LSD bulk reply indicated failure: op=[chars], [chars]/[dec] (nh=[chars], oif=[chars]): [chars]
Explanation LSD encountered a problem while trying to process bulked requests.
Recommended Action Make sure that LSD is running and LDP is connected/registered with it.
Error Message%ROUTING-LDP-3-LSD_INTF_ERR LSD mpls_interface '[chars]' failed for '[chars]': [chars]
Explanation LDP encountered some problem while trying to enable/disable MPLS on an interface via LSD server.
Recommended Action Make sure that LSD is running and LDP is connected/registered with it.
Error Message%ROUTING-LDP-3-LSD_LABEL_ALLOC_ERR LSD label alloc failed: [chars]
Explanation LDP encountered some problem while trying to allocate a label via LSD server.
Recommended Action Make sure that LSD is running and LDP is connected/registered with it. Moreover, check that there are enough free labels available.
Error Message%ROUTING-LDP-3-LSD_LABEL_FREE_ERR LSD label free failed for label [unsigned int]: [chars]
Explanation LDP encountered some problem while trying to free a label via LSD server.
Recommended Action Make sure that LSD is running and LDP is connected/registered with it. Moreover, check that the label was allocated before.
Error Message%ROUTING-LDP-3-LSD_LABEL_RECLAIM_ERR LSD label reclaim failed for label [unsigned int]: [chars]
Explanation LDP encountered a problem while trying to reclaim a label via LSD server.
Recommended Action Make sure that LSD is running and LDP is connected/registered with it. Moreover, check that the requested label is available.
Error Message%ROUTING-LDP-3-LSD_LABEL_REWRITE_ERR LSD label rewrite '[chars]' failed: [chars]/[dec] (nh=[chars], oif=[chars]), label=[unsigned int] : [chars]
Explanation LDP encountered some problem while trying to create/delete a forwarding rewrite using label rewrite API.
Recommended Action Make sure that LSD and LFD are running and the format/parameters of rewrite request are correct. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-3-LSD_REWRITE_ERR LSD rewrite '[chars]' failed: [chars]/[dec] (nh=[chars], oif=[chars]): [chars]
Explanation LDP encountered some problem while trying to create/delete a forwarding rewrite.
Recommended Action Make sure that LSD and LFD are running and the format/parameter of rewrite request are OK. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-3-MALFORMED_MSG Peer [chars]; format error for msg type [hex]
Explanation A Label Distribution Protocol (LDP) message that is malformed has been received from an LDP peer.
Recommended Action ACTION_NEW_SESSION_TDP
Error Message%ROUTING-LDP-3-MCAST_ERR Multicast op: [chars] [chars] on [chars] failed ([chars])
Explanation The above specified multicast operation failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-3-RPC_ERR RPC Error: func:[chars] op:[chars] err:[chars]
Explanation A remote procedure call error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-3-UNKNOWN_MPLS_APP [chars] [chars] message from [chars]; [chars];
Explanation A Label Distribution Protocol (LDP) message with an unknown label type and/or address family has been received from a peer, and the message has been dropped.
Recommended Action ACTION_COPY_REPORT_TDP
Error Message%ROUTING-LDP-4-PTCL Peer [chars], [chars]
Explanation A violation of the LDP protocol by a LDP peer has been detected.
Recommended Action ACTION_NEW_SESSION_TDP
Error Message%ROUTING-LDP-5-NBR_CHANGE Nbr [chars], [chars]
Explanation A LDP neighbor has changed state (up/down). This message appears only if the log-nbr-changes command is configured for the LDP process.
Recommended Action No action is required.
Error Message%ROUTING-LDP-6-GR_CHG Please restart LDP process for graceful restart to take effect
Explanation Graceful Restart config change will not be changed unless LDP is restarted.
Recommended Action After changing GR enable configuration, the change will not take effect immediately if any LDP sessions are active. To force GR feature change to take effect, use 'process restart mpls_ldp'.
MFWD_MA Messages
Error Message%ROUTING-MFWD_MA-3-CFG_ERR [chars] cfg counter already 0. Can't decrement : Item is [chars].
Explanation A general error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-DEBUG_ERR Error in attaching debug commands: [chars], file [chars], line [dec], function [chars]
Explanation An error related to the debugging subsystem occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ECM_ERR [chars] failed : [chars].
Explanation A general error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-GEN_ERR [chars] failed : [chars].
Explanation A general error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-GENINITFAIL Initialization failed: [chars] [chars]
Explanation An unrecoverable error occurred at system initialization time.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-IDB_ERR [chars] failed for [chars] [[hex]].
Explanation A general error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-SYSDB_ERR SysDB Oper - [chars] failed : [chars].
Explanation A general error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MPLS_HW Messages
Error Message%ROUTING-MPLS_HW-2-ERROR [chars]. Error = [chars] (errno=[dec]).
Explanation There was a critical system call failure resulting in a failure to provide some system service as indicated in the message text.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%ROUTING-MPLS_HW-2-ERROR [chars]. Error = [chars] (errno=[dec]).
Explanation There was a critical system call failure resulting in a failure to provide some system service as indicated in the message text.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%ROUTING-MPLS_HW-2-ERROR_TLU_ALLOC [chars]. Error = [chars] (errno=[dec]).
Explanation Hardware memory allocation for table lookup unit (TLU) failed. This can be because the system has more forwarding entries than supported limits or there is a software defect.
Recommended Action Please collect output of show tlu server summary [egress/ingress] loc to see why the line card is running out of forwarding entries. Then try to reduce the entries if possible. Copy the error message and report to your technical support representative.
Error Message%ROUTING-MPLS_HW-2-ERROR_TLU_WRITE [chars]. Error = [chars] (errno=[dec]).
Explanation Hardware memory write for table lookup unit (TLU) failed. This can because 1) connection to mipc lost. 2) mipc/metro problem.
Recommended Action Please collect output of show pse ipc clinet-connection all loc and show asic-errors pse [0|1] all loc . Copy the error message and report to technical support representative.
Error Message%ROUTING-MPLS_HW-2-ERROR_WITH_LABEL [chars]. Error = [chars] (errno=[dec]). Out label = [dec].
Explanation There was a critical system call failure resulting in a failure to provide some system service as indicated in the message text.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%ROUTING-MPLS_HW-2-ERROR_WITH_LABEL [chars]. Error = [chars] (errno=[dec]). Out label = [dec].
Explanation There was a critical system call failure resulting in a failure to provide some system service as indicated in the message text.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%ROUTING-MPLS_HW-6-INFO [chars]. Error = [chars] (errno [dec]).
Explanation There was an internal failure that may impact non-essential system function.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%ROUTING-MPLS_HW-6-INFO [chars]. Error = [chars] (errno [dec]).
Explanation There was an internal failure that may impact non-essential system function.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%ROUTING-MPLS_HW-6-INFO_WITH_LABEL [chars]. Error = [chars] (errno [dec]). Out label = [dec].
Explanation There was an internal failure that may impact non-essential system function.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%ROUTING-MPLS_HW-6-INFO_WITH_LABEL [chars]. Error = [chars] (errno [dec]). Out label = [dec].
Explanation There was an internal failure that may impact non-essential system function.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
MPLS_IMC_CLIENT Messages
Error Message%ROUTING-MPLS_IMC_CLIENT-4-DEBUG_REG_FAILED Lib IM client could not register for debugging ([chars])
Explanation MPLS LIB IM client library failed to register for debugging.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MPLS_LCAC Messages
Error Message%ROUTING-MPLS_LCAC-2-MEM_ALLOC_FAILED Memory allocation failed for [chars]
Explanation Allocation of memory failed.
Recommended Action Add more memory.
Error Message%ROUTING-MPLS_LCAC-3-INTERNAL_ERROR [chars]
Explanation An internal system error occured.
Recommended Action Copy the message exactly as it appears and report it to your technical service representative.
Error Message%ROUTING-MPLS_LCAC-4-SHOW_WARNING The show thread waited [unsigned int] seconds and could not acquire the mutex.
Aborting show request. Please try again. If this problem persists,
please contact your technical service representative.Explanation The show thread could not acquire the mutex to service the show request. The main thread in te_control may be busy/blocked/hogging while holding That mutex.
Recommended Action Try to run the show command again. If the error reoccurs, then check the state of the te_control process (show process te_control). If thread number 1 is blocked for an extended period of time, contact your technical service representative.
MPLS_LFD Messages
Error Message%ROUTING-MPLS_LFD-2-HARDWARE_INIT_FAILED MPLS LFD failed to initialize platform library: [chars]
Explanation Initialization of one of the platform components failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-2-MEM_ALLOC MPLS LFD could not allocate [dec] bytes memory for [chars]
Explanation Memory may be low.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-2-NO_LABEL_TABLE MPLS table [dec] for lookup is NULL - dropping MPLS packet
Explanation MPLS may not have been initialized correctly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-ADJ_ERR [chars]
Explanation Some error occurred in Adjacency related routines. The text of the error message explains the error and traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-ADJ_ERR_RC [chars] failed: [chars]
Explanation Some error occurred in Adjacency related routines. The text of the message displays the failed operation and the related error code, and traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-AIB_CLIENT_ERR [chars] failed: [chars]
Explanation Some error occurred in AIB client interactions. The text of the message displays the failed operation and the related error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-AIB_ERR [chars] failed: [chars]
Explanation Some error occurred in operations with AIB. The text of the message displays the failed operation and the related error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-BAG_ERR [chars] failed for '[chars]': [chars]
Explanation Some error occurred in Bag operations. The text of the message displays the failed operation and the related bafg with error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-BCDL_ERR [chars] failed: [chars]
Explanation Some error occurred in BCDL interactions. The text of the message displays the failed operation and the related error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-CONN_ERR [chars] failed for '[chars]': [chars]
Explanation Some error occurred in Connection related operations. The text of the message displays the failed operation and the related entity with error code. The traceback can be used to get the function/ line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-DEBUG_ERR [chars] failed: [chars]
Explanation Some error occurred in interactions with Debug infrastructure. The text of the message displays the failed operation and the related error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-EVENT_ERR [chars] failed: [chars]
Explanation Some error occurred in Event/EVM related operations. The text of the message displays the failed operation and the related error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-FIBV4_ERR [chars] failed: [chars]
Explanation Some error occurred in operations with IPv4 FIB collaborator. The text of the message displays the failed operation and the related error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-FRR_ERR [chars] failed: [chars]
Explanation Some error occurred in FRR (Protection) related operations. The text of the message displays the failed operation and the related error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-GENERIC_ERR [chars]
Explanation Some miscellaneous error. The text of the message explains the warning and traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-GENERIC_ERR_RC [chars] failed: [chars]
Explanation Some miscellaneous error. The text of the message explains the warning and error code, and traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-GTRIE_ERR [chars]
Explanation Some error occurred in MPLS gtrie routines. The text of the error message explains the error and traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-GTRIE_ERR_RC [chars] failed: [chars]
Explanation Some error occurred in MPLS gtrie routines while calling some API. The text of the error message contains the called API and string representation of cerrno. Traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-HARDWARE_UPDATE_FAILED MPLS LFD failed to update hardware [chars]
Explanation Lack of hardware resources.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-HW_ERR [chars] failed: [chars]
Explanation Some error occurred in interactions with Hardware/Platform. The text of the message displays the failed operation and the related error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-IM_ERR [chars] failed: [chars]
Explanation Some error occurred in operations with IM. The text of the message displays the failed operation and the related error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-INVALID_PARAM [chars]
Explanation Invalid parameter passed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-IO_ERR [chars] failed: [chars]
Explanation Some error occurred in operations performed by LFD Partner process. The text of the message displays the failed operation and the related error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-MEM_ERR [chars] failed for '[chars]'
Explanation Some error occurred in Alloc/Chunk related memory operations. The text of the message displays the failed operation and the related memory construct. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-NETIO_ERR [chars]
Explanation Some error occurred in NetIO routines/constructs. The text of the error message explains the error and traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-NETIO_ERR_RC [chars] failed: [chars]
Explanation Some error occurred in NetIO routines/constructs. The text of the error message explains the error and error code and traceback can be used to get the function/line number of error generating code.
Recommended Action *SUPPORT
Error Message%ROUTING-MPLS_LFD-3-NO_LFD_ADJ MPLS LFD adjacency NULL
Explanation MPLS may not have been initialized correctly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-PAK_ADD_HEAD_FAILED MPLS could not add [dec] bytes to beginning of pak
Explanation Buffer memory may be low.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-PAK_ERR [chars] failed: [chars]
Explanation Some error occurred in Packet (IP/MPLS/ICMP) related operations. The text of the message displays the failed operation and the related error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-PAK_ERR_NO_RC [chars] failed
Explanation Some error occurred in Packet (IP/MPLS/ICMP) related operations. The text of the message displays the failed operation. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-PFI_ERR [chars] failed: [chars]
Explanation Some error occurred in operations with PFI. The text of the message displays the failed operation and the related error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-SHM_ERR [chars] failed: [chars]
Explanation Some error occurred in operations related to Shared Memory area. The text of the message displays the failed operation and the related error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-STATS_ERR [chars] failed: [chars]
Explanation Some error occurred in operations with Statistics Infrastructure. The text of the message displays the failed operation and the related error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-SYSDB_DATALIST_ERR [chars] failed: [chars]
Explanation Some error occurred in datalist operations with SysDB EDM. The text of the message displays the failed operation and the related error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-SYSDB_ERR [chars] failed for '[chars]': [chars]
Explanation Some error occurred in SysDB operations (e.g. bind, register). The text of the message displays the failed operation and the related sysdb path with error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-SYSDB_GEN_ERR [chars] failed: [chars]
Explanation Some error occurred in SysDB operations (not involving some path). The text of the message displays the failed operation with error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-SYSDB_LIST_ERR [chars] failed: [chars]
Explanation Some error occurred in list operations with SysDB EDM. The text of the message displays the failed operation and the related error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-TIMER_ERR [chars] failed for '[chars]': [chars]
Explanation Some error occurred in Managed Timer related operations. The text of the message displays the failed operation and the related timer construct with error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-UNKNOWN_FPI_HANDLER MPLS LFD received an LSD update for FPI type [dec], [chars] handler NULL
Explanation Message corruption possible.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-UNKNOWN_LSD_UPDATE MPLS LFD received an unknown LSD update type [dec]
Explanation Message corruption possible.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-WAVL_ERR [chars] failed (tree=[chars])
Explanation Some error occurred in WAVL operations The text of the message displays the failed operation and the related wavl tree. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-3-WAVL_ERR_RC [chars] failed (tree=[chars]): [chars]
Explanation Some error occurred in WAVL operations The text of the message displays the failed operation and the related wavl tree with error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-4-GENERIC_WARN [chars]
Explanation Some miscellaneous warning. The text of the message explains the warning and traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-4-IM_WARN [chars] failed: [chars]
Explanation Some error occurred in operations with IM. The text of the message displays the failed operation and the related error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-6-GEN_INFO [chars]
Explanation Some informational message.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LFD-6-GEN_INFO_CERR [chars]: [chars]
Explanation Some informational message with cerrno.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MPLS_LIB Messages
Error Message%ROUTING-MPLS_LIB-2-DBG_REGISTER_FAILED Error registering for IGP debug events: [hex], '[chars]'
Explanation IGP failed to register with the debug module for printing messages.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LIB-3-SYSDB SysDB Error: [chars]
Explanation An error occurrred when accessing the system database
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. The process must be restarted before it can function correctly.
Error Message%ROUTING-MPLS_LIB-4-DATA_QUEUE_FULL message queue is full. Cannot accept more element.
Explanation Data queue is full and it cannot accept more element. It could be a result of memory limitation.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration..
Error Message%ROUTING-MPLS_LIB-4-ERR_CLINFO_HOLD Error in saving client's message channel information
Explanation IGP failed to save its client's message channel information. This could be a result of channel down or resource allocation failure.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration..
Error Message%ROUTING-MPLS_LIB-4-ERR_CLINFO_UNHOLD Error in releasing client's message channel information
Explanation IGP failed to release its client's message channel information. This could be a result of channel down already.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration..
Error Message%ROUTING-MPLS_LIB-4-INVALID_TLV Data ([dec]) is too big or small([dec])
Explanation Failed to send data due to the limitation of the buffer size. This is an internal error. It requires to reduce the number of interfaces.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration..
Error Message%ROUTING-MPLS_LIB-4-MEM_ALLOC_FAIL Failed to allocate [unsigned int] bytes for '[chars]'
Explanation The process failed to allocate memory for the specified resource. This could be because the topology is too large for the memory installed in the router.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration..
MPLS_LSD_CLIENT Messages
Error Message%ROUTING-MPLS_LSD_CLIENT-3-BAD_PARAM Bad parameter: [chars] ([chars])
Explanation LSD client library received a call with a bad parameter.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LSD_CLIENT-4-DEBUG_REG_FAILED LSD client could not register for debugging ([chars])
Explanation LSD client library failed to register for debugging.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MPLS_LSD Messages
Error Message%ROUTING-MPLS_LSD-2-EVENT_MGR_INIT_FAILED Initialization of MPLS LSD event manager failed (Operation: [chars]) - [chars]
Explanation Initialization of the LSD's event manager failed
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LSD-2-SERVER_INIT_FAILED Initialization of MPLS LSD failed (Operation: [chars]) - [chars]
Explanation Initialization of one of the LSD's modules failed
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LSD-3-CLIENT_NOT_FOUND Module([chars]) could not find client entry from connection
Explanation Client entry cannot be found from a connection.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LSD-3-MSG_REPLY_FAILED Module([chars]) had msg_reply() call fail
Explanation A call to msg_reply failed
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MPLS_NETIO Messages
Error Message%ROUTING-MPLS_NETIO-3-AIB_ERR [chars] FAILED: [chars]
Explanation Some error occured in operations with AIB collaborator. The text of the message displays the failed operation and error msg explain the reason. The traceback can be used to get the function/line number of error generating code.
Recommended Action *SUPPORT
Error Message%ROUTING-MPLS_NETIO-3-GENERIC_ERR [chars]
Explanation Some miscellaneous error occured. The text of the message explains the err/warning and traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_NETIO-3-LFD_ERR [chars] FAILED: [chars]
Explanation Some error occured in operations with LFD DLL/APIs. The text of the message displays the failed operation and error msg explain the reason. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_NETIO-3-PARTNER_ERR [chars] FAILED for partner '[chars]'
Explanation Some error occured in operations with its partner process. The text of the message displays the failed operation. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_NETIO-3-PLATFORM_ERR [chars] FAILED
Explanation Some error occured in operations with platform collaborator. The text of the message displays the failed operation. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_NETIO-5-CLEAR_MAPPING_FAILED control clear mapping for [chars] mpls proto [dec] failed [chars]
Explanation MPLS could not clear control mapping for underlying protocol.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_NETIO-5-SET_MAPPING_FAILED control set mapping for [chars] to [hex]/[hex] mpls proto [dec] failed [chars]
Explanation MPLS could not set control mapping for underlying protocol.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_NETIO-6-DEBUG_ERR [chars] FAILED: [chars]
Explanation Some error occured in operations with debug infra. The text of the message displays the failed operation and error msg explain the reason. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MPLS_STATIC Messages
Error Message%ROUTING-MPLS_STATIC-2-INIT_FAILED Initialization of MPLS Static failed - [chars] ([chars])
Explanation Initialization of the MPLS Static process failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_STATIC-3-CONN_FAILED Connection to the [chars] failed ([chars])
Explanation MPLS static process could not connect with a manager.
Recommended Action No action is required.
Error Message%ROUTING-MPLS_STATIC-4-MEM_ALLOC_FAILED Memory allocation failed for [chars]
Explanation Allocation of memory failed.
Recommended Action Add more memory.
MPLS_TE Messages
Error Message%ROUTING-MPLS_TE-2-MEM_ALLOC_FAILED Memory allocation failed for [chars]
Explanation Allocation of memory failed.
Recommended Action Add more memory.
Error Message%ROUTING-MPLS_TE-3-BACKUP_TUNNEL_ERROR Backup tunnel [chars] cannot be used. Please ensure that it has an IP address and reapply backup-path
Explanation Backup tunnel cannot be used. This is possibly due to the lack of an IP address.
Recommended Action Assign an IP address to the backup tunnel.
Error Message%ROUTING-MPLS_TE-3-BAG_ERROR [chars]: [chars]: [chars]
Explanation A Bag related error occurred.
Recommended Action Copy the message exactly as it appears and report it to your technical service representative.
Error Message%ROUTING-MPLS_TE-3-CONSISTENCY [chars]: [chars] [chars] [chars]
Explanation An action attempted by the traffic engineering tunnel implementation encountered an unexpected condition.
Recommended Action Copy the message exactly as it appears and report it to your technical service representative.
Error Message%ROUTING-MPLS_TE-3-INTERNAL_ERROR [chars] : [chars]
Explanation An internal system error occurred.
Recommended Action Copy the message exactly as it appears and report it to your technical service representative.
Error Message%ROUTING-MPLS_TE-3-SYSDB_ERROR [chars]: [chars] failed for path [chars] : [chars]
Explanation A sysdb error occurred.
Recommended Action Copy the message exactly as it appears and report it to your technical service representative.
Error Message%ROUTING-MPLS_TE-3-SYSDB_FREE_ERROR [chars]: [chars]: [chars]
Explanation A SysDB free related error occurred.
Recommended Action Copy the message exactly as it appears and report it to your technical service representative.
Error Message%ROUTING-MPLS_TE-3-TUNNELKILL Tunnel removal attempt (by [chars]) failed for tunnel [chars]: [chars]
Explanation State associated with a TE tunnel could not be completely removed because of an internal failure.
Recommended Action Copy and save this message. If possible, restart TE-control and rsvp processes to clean up the state. If the message recurs, copy and save the message and call your technical support representative for assistance.
Error Message%ROUTING-MPLS_TE-4-SHOW_WARNING The show thread waited [unsigned int] seconds and could not acquire the mutex. Aborting show request. Please try again. If this problem persists, please contact your technical service representative.
Explanation The show thread could not acquire the mutex to service the show request. The main thread in te_control may be busy/blocked/hogging while holding That mutex.
Recommended Action Try to run the show command again. If the error reoccurs, then check the state of the te_control process (show process te_control). If thread number 1 is blocked for an extended period of time, contact your technical service representative.
Error Message%ROUTING-MPLS_TE-4-SHUTDOWN Process is shutting down ([chars]): [chars]
Explanation TE process has encountered a problem which means it is no longer able to continue and is shutting down. The message includes a brief description of the problem. The message also describes whether or not TE process has automatically been restarted.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Follow the instructions associated with this message. If message states that an automatic restart has been scheduled, then TE process will recover automatically. If a manual restart is required, then 'process start te_control' is required to recover.
Error Message%ROUTING-MPLS_TE-4-WARN [chars]
Explanation An internal system warning occurred.
Recommended Action Copy the message exactly as it appears and report it to your technical service representative.
MRIB_API Messages
Error Message%ROUTING-MRIB_API-3-ASYNC_ERR Asynchronous error: [chars]
Explanation 'An unhandled asynchromous error occurred in the MRIB API'
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB_API-3-CORRPT Corrupted update: [chars]. (expected [dec] bytes, got [dec] bytes)
Explanation 'A corrupted update was received form the MRIB by the MRIB API'
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB_API-3-GENINITFAIL Initialization failed: [chars] [chars]
Explanation Error occurred at client initialization.
Recommended Action No action is required.
Error Message%ROUTING-MRIB_API-3-RPC_FAIL RPC unexpected error: [chars]
Explanation 'An RPC-related error occurred in an RPC call from the MRIB API'
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB_API-7-ASYNC_WAR Warning: [chars]
Explanation 'A recoverable error condition occurred in the MRIB API'
Recommended Action No action is required.
MRIB Messages
Error Message%ROUTING-MRIB-2-NOMEMORY No memory for [chars] in [chars]
Explanation The requested operation could not be accomplished because of a low memory condition.
Recommended Action This indicates a low memory condition. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-MRIB-2-NORESOURCE Resource unavailable for [chars] in [chars]
Explanation The requested operation could not be accomplished because of a low memory condition.
Recommended Action This indicates a low memory condition. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-MRIB-3-BCDL_ERR Failed to [chars]: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-EDM_INIT Error in EDM activity : [chars] - [chars]
Explanation An error occurred when MRIB tried to initialize conn to Sysdb for show commands.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-GEN_ERR Failed to [chars]
Explanation A general error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-GENCOMMERR Communication error: [chars] [chars]
Explanation A Inter Process Communication error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-GENINITFAIL Initialization failed: [chars] [chars]
Explanation An unrecoverable error occurred at system initialization time.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-INTERNALERR Internal error: [chars] in [chars] line [dec] ([chars])
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-LWM_ERR MRIB LWM error: [chars] - [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-MOD_INTF_LIST Interface [chars] has no modified flags. Shouldn't be present in list.
Explanation An error occurred when MRIB tried to walk the modified interfaces list.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-NSFSTATE Error modifying MRIB Non-stop Forwarding state in [chars]: [chars]
Explanation An internal error occurred when MRIB attempted to transition to/from Non-stop Forwarding mode.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-REDUCEDFUNCT Initialization of [chars] functionality failed
Explanation The initialization of a functionality failed. This component migh still operate without the functionality.
Recommended Action This indicate a resource shortage. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-MRIB-3-TREE_OPER Failed to [chars] [chars] interface in interface tree of [chars].
Explanation An error occurred when MRIB tried to perform a tree operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-4-DEBUGERR Debugging error: [chars] in [chars] line [dec] ([chars])
Explanation An error related to the debugging subsystem occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-4-FILTRVIOLERR Filter violation error: conn [dec] ([chars]:[chars]) in [chars]
Explanation A client tried to modify a route attribute not owned by it
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-4-INCORRECTPARS Illegal parameter in function call ([chars]) in [chars]
Explanation An externally accessible function has been called with illegal parameter(s). the parameter(s) has been casted to an acceptable value.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-4-NOMEMORYW No memory for [chars] in [chars]. Handling: [chars]
Explanation The requested operation could not be accomplished because of a low memory condition but the problem has ben handled locally.
Recommended Action This indicates a low memory condition. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
MSDP Messages
Error Message%ROUTING-MSDP-3-ACL_ERR acl error: [chars] [chars] [chars]
Explanation Check if access list is configured as intended
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-MSDP-3-BAD_STATE the peer [chars] has changed to an illegal state: [dec]
Explanation The state was not one of the valid states
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-CACHE_ERR cache error: [chars] [chars]
Explanation An error occured updating the SA cache.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-CONNECTION_ERR [chars] error: [chars]
Explanation A peer has incorrectly attempted to establish a connection with us. Possible causes may include a passive peer trying to make an active connection, in this case the connection will be rejected. Recieving a connection request from a peer that is in the Established state, in this case the current, if the peer is active, the existing connection will be terminated and the new connection will be acted upon. recommended_action: Gather as much relavent information from the respective peer. *SUPPORT*
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-EDM_ERR error: show server error: [chars] [chars]
Explanation An error occured with a show client communicating with the msdp. show server.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-EVENT_FAILED event [chars] failure: [chars]
Explanation An unrecoverable error occurred during the event loop.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-IARM_REG_ERR Failed to register on interface [chars]: [chars]
Explanation An error occured when registering to IARM.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-IARM_UPDATE_ERR Failed to update: [chars]
Explanation An error occured when registering to IARM.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-INIT_FAILED Initialization failed: [chars]
Explanation An unrecoverable error occurred at system initialization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-INIT_FAILED2 Initialization failed: [chars], [chars]
Explanation An unrecoverable error occurred at system initialization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-INTERNAL_STATE_ERR [chars]: [chars] [chars]/[chars]
Explanation An error occured due to inconsistent internal state.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-IO_FAILED I/O failure: [chars] [dec], [chars], [chars]
Explanation An error has occurred during a socket operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-LPTS_POLICY_ERR Failed to [chars] lpts policy for peer [chars] [[dec]]
Explanation Some socket/lpts error occured.
Recommended Action Consult the configuration documentation for appropriate commands.
Error Message%ROUTING-MSDP-3-LTRACE_INIT ltrace_init failed for '[chars]': [chars]
Explanation Internal error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-MRIB_ERR mrib error: [chars], [chars]
Explanation An error has occurred during communication with the MRIB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-NOTIFY [chars] notification [chars]: code: [dec], subcode [dec]
Explanation An error was encountered during communication with specified peer.
Recommended Action Observe error details to determine cause of problem. If that does not help turn on 'debug ip msdp tlv'.
Error Message%ROUTING-MSDP-3-OUT_OF_MEMORY out of memory: [chars] [chars]
Explanation Eliminate system processes or add memory
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-MSDP-3-OUT_OF_RESOURCE [chars] active SA limit [dec] exceeded SA count
Explanation Resource limit has been hit
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-MSDP-3-SOCKET_ERR socket([dec]) error: [chars] [chars]
Explanation An unrecoverable error occured during a socket operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-SYSDB_ERR sysdb error: [chars] [chars]
Explanation An error occured while communicating with sysdb.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-WDSYSMON_EVENT_ERROR Received an invalid event from WDSysmon
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-WDSYSMON_REGISTER_ERROR [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-4-BAD_MASKLEN invalid mask length, must be 32 ([chars]/[dec]): [chars]
Explanation A masklen other than 32 was attempted'
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-4-BGP bgp client: [chars] [chars]
Explanation Problem communicating with BGP
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-4-CONFIG_FAILED config failed: [chars] [chars], [chars]
Explanation 'reconfigure'
Recommended Action Consult the configuration documentation for appropriate commands.
Error Message%ROUTING-MSDP-4-MRIB_WARN warning mrib: [chars]: [chars]
Explanation An problem comminicating with the mrib.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-4-OOM_STATE_THROTTLE Received [chars] memory depletion warning, stop creating new msdp SA state
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-4-OOM_STATE_UNTHROTTLE Node memory back to normal, new msdp states will be created
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-4-PEER_ERR peer error: [chars] [chars]
Explanation Some peer error occured.
Recommended Action Consult the configuration documentation for appropriate commands.
Error Message%ROUTING-MSDP-4-RIB_ERR rib error: [chars] [chars]: [chars]
Explanation An error has occurred during communication with the RIB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-4-SA_MESSAGE [chars]: error in SA ([chars], [chars]): [chars]
Explanation Error in the SA message format or contents.
Recommended Action Turn on 'debug ip msdp tlv' for more information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-4-TIMER timer error has occured
Explanation A timer error has occur
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-5-INIT_PEER_UP_DOWN [chars] [chars] [chars]
Explanation MSDP Peer UP/DOWN.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-6-INIT_BASIC [chars]: pid [dec]
Explanation MSDP Initialized.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-6-INIT_INFO retried [chars] [chars] [dec]
Explanation An unrecoverable error occurred at system initialization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MULTIVER Messages
Error Message%ROUTING-MULTIVER-3-DLLFAIL Could not load DLL [chars]: [chars]
Explanation There was a problem loading the DLL - perhaps the router has run out of memory, or there was a problem reading the file.
Recommended Action Check to make sure that one or more nodes is not having problems with memory.
ORA_SHARED Messages
Error Message%ROUTING-ORA_SHARED-4-CERR_REG Unable to register cerrno dll [chars] because [chars]
Explanation The given cerrno dll could not be marked for use. This does not change the functionality of the system but does obscure the meaning of error codes presented by this part of the system.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
ORA Messages
Error Message%ROUTING-ORA-2-INSUFMEM Cannot allocate entry
Explanation The requested operation could not be accomplished because of a low memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ORA-3-DBGINIT Unable to bring up debug event structures: [chars]
Explanation The debug event initialization failed. The ora docker will still run correctly, but debug commands may be unavailable.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-3-DBGSHUTDOWN Unable to shutdown debug event structures: [chars]
Explanation The debug event shutdown failed. The ora docker will still run correctly, but debug commands may be unavailable.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-3-DOCKENTRY Dock entry add failure
Explanation I really do not know.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-3-INIT Failure in init function in DLL [chars]
Explanation The library is incorrectly installed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-3-MERGE_FAILED Some base type(s) was(were) unavailable during AP merging at: [chars]
Explanation One or more base types where not available when bringing together the parts of this attach point. This is an item that should be caught during testing. If it does show up, support should be contacted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-3-MISSING_BASE_TYPE The base type '[chars]' v'[chars]' was used as a [chars] in a [chars]: '[chars]' type in area [chars]
Explanation One of the operations in one of the ORAs used a base type that was not defined in any of the ORA math sets.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-3-MISSING_OPERATOR The operator '[chars]' was not located in any of the '[chars]'s ORAs.
Explanation There is a function declared within the various docked ORAs at this attach point that uses an operator that does not exist with the same set of docked ORAs. Please contact support.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-3-MISSINGFUNCTION Route access library [chars] has no [chars] function
Explanation The library is incorrectly installed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-3-THREADING_FAILURE Threading operation '[chars]' for '[chars]' failed because: [chars]
Explanation The presented threading operation failed. It is likely that policy multi-version calls will stop working and thus policy may not be operational.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-4-CERR_REG Unable to register cerrno dll [chars] because [chars]
Explanation The given cerrno dll could not be marked for use. This does not change the functionality of the system but does obscure the meaning of error codes presented by this part of the system.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-4-MISSING_DOCK_INFO The dock data for docking item [chars] was missing
Explanation This is most likely an internal logic error that resulted in a given ora dockling being released more than once.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-6-SUCCESS ORA [chars] is loaded.
Explanation The route access library attached correctly.
Recommended Action No action is required.
OSPF_EDM Messages
Error Message%ROUTING-OSPF_EDM-3-DATALIST_ADD_FAILED Failed to add an external data manager datalist for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The attempt to add an item to an external data manager datalist has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_EDM-3-DATALIST_CREATE_FAILED Failed to create external data manager datalist for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The creation of the external data manager datalist has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_EDM-3-DATALIST_SET_MORE_FLAG Failed to set external data manager more flag for datalist [chars]
Explanation A client has requested information through SysDB from OSPF. During execution of the request an attempt to set a flag indicating there is more data for the client failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_EDM-3-ENCODE_FAILED Failed to encode [chars] data in external data manager
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The data requested could not be encoded.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_EDM-3-LIST_ADD_FAILED Failed to add to an external data manager list for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The attempt to add an item to an external data manager list has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_EDM-3-LIST_CREATE_FAILED Failed to create external data manager list for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The creation of the external data manager list has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_EDM-3-SYSDB_BIND_FAILED Failed to connect to SysDB ([chars])
Explanation The process failed to connect to SysDB while starting.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
OSPF_POLICY Messages
Error Message%ROUTING-OSPF_POLICY-3-ORA_INSTBUILD Failed to build [chars], reason [chars] cer [chars]
Explanation Internal error in policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_POLICY-3-ORA_RUN Could not apply policy operation [chars] to attribute [chars] because [chars]
Explanation Internal error in policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
OSPF_RIB Messages
Error Message%ROUTING-OSPF_RIB-3-ERR_PATH_ADD Error adding path to batching buffer
Explanation An error was encountered in the call to ipv4_rib_batch_add_path.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-3-ERR_PATH_DELETE Error deleting path from batching buffer
Explanation An error was encountered in the call to ipv4_rib_batch_delete_path.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-3-ERR_PROTO_MODIFY Error changing purgetime
Explanation An error was encountered in the call to ipv4_rib_protocol_modify.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-3-ERR_ROUTE_HDR Error adding route header to batching buffer for [chars]/[dec]
Explanation An error was encountered in the call to ipv4_rib_batch_add_route.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-3-ERR_UPDATE_DONE Error informing rib that batch is complete
Explanation An error was encountered in the call to ipv4_rib_batch_complete.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-4-BATCH_LOG_PATH RIB batch error, [chars] (result [dec]), prefix [hex]/[dec] next_hop [hex] intf [chars].
RetryingExplanation The specified error was encountered in the OSPF RIB batching code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-5-BATCH_ERROR RIB batch error, [chars]
Explanation The specified error was encountered in the OSPF RIB batching code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-5-BATCH_ERROR_CODE RIB batch error, [chars] ([hex])
Explanation The specified error was encountered in the OSPF RIB batching code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-6-INFO_RT_HDR_NOTUSED Believes [chars]/[dec] and [chars]/[dec] differ
Explanation The RIB batching API believes that it already has this router header in the batching buffer.
Recommended Action No action is required.
Error Message%ROUTING-OSPF_RIB-7-CONN_INFO INFO ONLY: Closing the connection to the global RIB.
Explanation The connection to the RIB has closed. In most cases it will reappear within a short period.
Recommended Action No action is required.
OSPF_UV Messages
Error Message%ROUTING-OSPF_UV-3-CERR_REG_FAIL Failed to register internal error codes: [chars]
Explanation An error occurred during the registration of OSPF error codes.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_DBG_REGISTER_FAILED Error initializing ospf_uv debugging: [chars]
Explanation An error occurred during initialization of the ospf_uv process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_MEM_ALLOC_FAIL Unable to allocate [unsigned int] bytes for '[chars]'
Explanation The ospf_uv process was unable to allocate memory for the specified resource.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_PROC_READY Error signaling process ready: [chars]
Explanation The ospf_uv process was unable to signal process ready to sysmgr.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_SYSDB_CONNECT Error binding to SysDB: [chars]
Explanation The ospf_uv process was unable to bind to SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_SYSDB_DISCONNECT Error unbinding from SysDB: [chars]
Explanation The ospf_uv process was unable to unbind from SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_SYSDB_REG_VERIFY Error registering with SysDB: [chars]
Explanation The ospf_uv process was unable to register with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_VRFN_FNS_INIT Error setting SysDB callback functions: [chars]
Explanation The ospf_uv process was unable to initialize SysDB callbacks.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-EVENT_ERR Error in event loop: [chars]
Explanation An error occurred in the main ospf_uv event loop.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-EVM_CRE_FAIL Error creating event connection manager: [chars]
Explanation The ospf_uv process was unable to create an event connection manager instance.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-INTF_FWS_INIT Error initializing forward-reference store: [chars]
Explanation The ospf_uv process was unable to initialize the forward-reference store library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-6-PROCESS_NAME Caution: The OSPF process name [chars] conflicts with a show or clear command name
Explanation The name chosen for the OSPF process matches an ospf show or clear command, or a command abbreviation. This can cause ambiguities with subsequent show or clear commands for this process.
Recommended Action Choose a different name for the OSPF process.
OSPF Messages
Error Message%ROUTING-OSPF-2-BADSHARE Bad refcount in [chars], ptr=[hex], count=[hex]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-2-INIT_FAIL Init failure, [chars], process terminated
Explanation An error occurred during initialization, causing the process to terminate.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-2-NOMEMORY No memory, [chars]
Explanation Allocation of the specified resource failed because of a low memory condition.
Recommended Action This indicates a low memory condition. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-OSPF-2-NOMEMORY_FATAL No memory, [chars], process terminated
Explanation Memory allocation of a critical OSPF resource failed because of a low memory condition. The OSPF process was terminated.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-ALLOC_ERR Allocation error, [unsigned int] bytes for [chars]
Explanation OSPF was unable to allocate memory for the specified resource.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-AREANULL [chars]: area pointer is NULL
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-BADMSG ospf router received bad message type [dec]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-BADTIMER Managed Timer error, [chars]: Unrecognized timer type [dec]
Explanation A timer was found with an unrecognized type
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-DBGINIT Debug init error, [chars]: event [chars], error [dec]
Explanation Unable to initialize a debugging flag
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-DUP_RTRID OSPF detected duplicate router-id [chars] from [chars] on interface [chars]
Explanation OSPF received hello packet from a neighbor which has the same router-id as this routing process. A full adjacency cannot be established.
Recommended Action OSPF router-id should be unique. Change the neighbors router-id.
Error Message%ROUTING-OSPF-3-EVM External Event Manager error, [chars], error [chars] [[hex]]
Explanation A call to an external event manager function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-EVM_CODE External Event Manager error, [chars]: [chars] code [dec], error [chars] [[hex]]
Explanation A call to an external event manager function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-EXTERNALERR External error, [chars]
Explanation An external software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-EXTERNALERR_RC External error, [chars], error [hex]
Explanation An external software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-FRIS FRIS error, [chars], [chars] error [chars] [[hex]]
Explanation The FRIS request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-IDBERR IDB error, [chars]: [chars], intf [chars] cerr [chars]
Explanation Error encountered while attempting to activate an idb. Problem could be corrupt data from IM or IP/ARM or the FRIS.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-IFCHECK Interface [chars] is attached to more than one area
Explanation An internal consistency check has failed. An interface appears to be associated with more than one area.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-IFINIT Interface init error, interface [chars]
Explanation OSPF failed to initialize data structures for an interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-IFMGR External IFMGR error, [chars], intf [chars] error [chars] [[hex]]
Explanation The specified interface manager request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-IGPTE IGP/TE error, [chars]: [chars] error [dec]
Explanation Error encountered while attempting to use the IGP_TE Lib.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-INIT_ERR Init error, [chars], error [hex]
Explanation An error occurred during initialization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-INTERNALERR Internal error, [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-INTERNALERR_RC Internal error, [chars], error [hex]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-IPARM External IP-ARM error, [chars], error [chars] [[hex]]
Explanation A call to an external IP-ARM function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-LWM External light-weight msg error, [chars], error [chars] [[hex]]
Explanation A call to an external light-weight messaging function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-MCAST Multicast error, [chars] [chars] on [chars], error [chars]
Explanation The above specified multicast operation failed
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-MEDIAERR Media error, [chars]: Interface [chars] unknown type: [chars]
Explanation Media table lookup failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-MUTEX Mutex error, [chars], [chars] mutex, error [chars] [[hex]]
Explanation An error occurred in the pthread functions used for thread synchronization. This is most likely a system error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-NOBACKBONE Flagged as being an ABR without a backbone area
Explanation The router was flagged as an Area Border Router (ABR) without backbone area in the router.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-NOIPADDR No IP Addr on interface [chars]. OSPF will not be run over it.
Explanation This message is displayed if ospf is configured on an unnumbered interface that is not of type point to point. In this case, ospf will not run on this interface.
Recommended Action No action is required.
Error Message%ROUTING-OSPF-3-NOSELF if [chars] if_state [dec]
Explanation An internal error occurred. An interface was not fully initialized when an OSPF related event occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-NOTNBRTYPE Cannot configure neighbor on [chars]. Interface must be NBMA or P2MP
Explanation Neighbor cannot be configured on interface if it is not type NBMA or point to multipoint.
Recommended Action No action is required.
Error Message%ROUTING-OSPF-3-PKTDROP Raw socket error, [chars]: packet dropped, [chars]
Explanation An input packet was dropped for the specified reason.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-RDB_NO_LSA lsid [chars] adv [chars] type [dec] gateway [chars] metric [dec] network [chars] mask [chars] attr [hex] net-metric [dec]
Explanation OSPF found inconsistency between its database and topology table.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-RECONF_VL OSPF process [chars] is changing router-id. Reconfigure virtual link neighbors with our new router-id
Explanation OSPF process is being reset, and it is going to select a new router-id. This will bring down all virtual links. To make them work again, virtual link configuration needs to be changed on all virtual link neighbors.
Recommended Action Change virtual link configuration on all the virtual link neighbors, to reflect our new router-id.
Error Message%ROUTING-OSPF-3-RIB External RIB error, [chars], error [chars] [hex]
Explanation A call to an external RIB function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-RIB_MSG External RIB error, [chars]
Explanation A call to an external RIB function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-RPC External RPC error, [chars], error [chars] [[hex]]
Explanation An RPC error occurred
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-SOCKET External socket error, [chars], error [chars] [[hex]]
Explanation The above specified socket operation failed
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-SYSDB External SysDB error, [chars], error [chars] [[hex]]
Explanation An external OSPF error occurred when accessing the system database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-THREAD_CREATE Thread create error, [chars], error [chars] [[hex]]
Explanation OSPF failed to create a thread essential to its operation. This is an internal error. An automatic restart of the OSPF process was necessary to attempt recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-UNKNOWNSTATE Reached unknown state in neighbor state machine
Explanation An internal software error occurred. When processing and DBD packet, the neighbor was found to be in an indeterminate state.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-BADLENGTH Invalid length [dec] in OSPF packet from [chars] (ID [chars]), [chars]
Explanation The system received an OSPF packet with a length field of less than normal header size or inconsistent with the size of the IP packet in which it arrived. This indicates an error in the sender of the packet.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-BADLSATYPE Invalid lsa: [chars] Type [dec], LSID [chars] from [chars], [chars], [chars]
Explanation The router received an LSA with invalid LSA Type. The cause is either memory corruption or unexpected behavior on a router.
Recommended Action Check both the sending and receiving routers for memory corruption. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-CONFLICTING_LSAID Found LSA with the same host bits but different mask.
LSA with shorter mask will be used.
LSA 1: [chars]/[dec]
LSA 2: [chars]/[dec]Explanation An LSA could not be generated because there is a supernet lsa with the host bit set LSA ID that conflicts with the major net LSA ID that also needs to have host bit set.
Recommended Action This is a limitation in OSPF's ability to handle conflicting LSA IDs. Attempt to avoid this limitation by modifying the generation of summary LSA's so that the LSA ID's do not conflict. Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-ERR_MSG_GET_SCOID Error retrieving client's connection ID to the [chars] channel: [chars] ([dec])
Explanation OSPF failed to retrieve its local connection ID for a client attached to the specified channel. This is an internal programming error.
Recommended Action Restart the OSPF process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-ERR_MSG_REPLY Error replying to the client [chars]: [chars] ([dec])
Explanation OSPF failed to reply to its client through message channel. This could be a result of channel down or resource allocation failure.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Restart the OSPF process. *RECUR*
Error Message%ROUTING-OSPF-4-ERRRCV Received invalid packet: [chars] from [chars], [chars]
Explanation An invalid OSPF packet was received. Details are included in the error message. The cause might be a misconfigured OSPF or an internal error in the sender.
Recommended Action Check the OSPF configuration of the receiver and the sender for inconsistency. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-IFINDEX_GET Unable to get interface index for [chars]: [chars]
Explanation An error occurred when trying to get a numeric interface index value for the specified interface. Ietf nsf restart might fail.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-INVALID_RTRID_IF Invalid router id interface [chars]. Be sure the interface exists and has an IP address.
Explanation The user has requested that the OSPF router id be taken from an invalid interface. The interface either does not exist or it does not have an IP address.
Recommended Action Remove the OSPF router-id configuration until the interface configuration is corrected.
Error Message%ROUTING-OSPF-4-KEYCFG Key [unsigned long int] [chars]
Explanation An error occurred when trying to configure an ospf authentication key.
Recommended Action No action is required.
Error Message%ROUTING-OSPF-4-MAX_INTF_APPLY Interface limit [dec] exceeded. Dropping interface [chars]
Explanation The number of interfaces configured exceeds the interface limit.
Recommended Action Either raise the maximum interface limit or unconfigure interfaces until the number is below the limit.
Error Message%ROUTING-OSPF-4-MUTEX_ERR [chars] [chars] mutex ([hex]), tid [dec] owner [hex] count [dec], error [chars] [[hex]]
Explanation An error has been returned by the functions used for locking/unlocking an OSPF synchronization mutex.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-NBREXIST Neighbors were configured when NBMA or P2MP. Changing network type will abandon that configuration. Please remove configured neighbors.
Explanation Neighbors had been configured earlier when the network type was nonbroadcast. The current configuration request will cause these configured neighbors to be abandoned.
Recommended Action Remove the configured neighbors.
Error Message%ROUTING-OSPF-4-NONEIGHBOR Received [chars] from unknown neighbor [chars]
Explanation OSPF hello, database description, or database request packet was received, but the router could not identify the sender. This is a normal occurrance if a link flap occurs on the router receiving the packet.
Recommended Action This situation should correct itself. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-NORTRID OSPF process [chars] cannot start without a router id. Configure router-id with the
outer-id command.Explanation OSPF failed while attempting to allocate a router ID from the IP address of one of its interfaces as no suitable IP address was available.
Recommended Action Make sure that there is at least one interface that is up and has a valid IP address. If there are multiple OSPF processes running on the router, each requires a unique router ID. You must have enough 'up' interfaces so that each of them can obtain a router ID. It is highly recommended that you configure loopback interfaces or use the router-id configuration command to better control the selection of OSPF router IDs.
Error Message%ROUTING-OSPF-4-NOTREDIST5 db_free: external LSA [chars]/[dec]
Explanation An internal software error occurred. OSPF is deleting an external LSA that should not be deleted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-OLD_CMD Command [chars] has been upgraded by [chars]. Use the new command.
Explanation The command has been replaced by a newer command.
Recommended Action Use the new command inidicated in the message.
Error Message%ROUTING-OSPF-4-PAKMAN_EVENT Pakman event [chars] received, code=[dec], [chars]
Explanation An error has occured and pak manager sent use an event. If we can't recover from the error (ABORT event), OSPF will exit.
Recommended Action This is an indication that error(s) has occured in pakman No specific actions are required for OSPF.
Error Message%ROUTING-OSPF-4-POLICYCONFIG An error was encountered configuring policy, [chars]: [chars]
Explanation A problem was encountered while setting up route policy configuration. Some of the routing policy may not have been configured correctly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-RAW_OUTPUT_ERR Raw socket output err: [chars], src=[chars], dest=[chars], if=[chars], msglen=[dec]
Explanation An error has occured when OSPF is in process of sending a packet to the the raw socket.
Recommended Action This is an indication that error(s) has occured in other components and it is impacting OSPF's ability send data. No specific actions are required for OSPF.
Error Message%ROUTING-OSPF-4-REDIST_FAILED OSPF was unable to configure redistribution for protocol [chars]
Explanation An error occurred while OSPF was setting up redistribution for the named protocol. The redistribution will not take place.
Recommended Action This may be due to lack of memory, or due to a RIB failure, or to an internal OSPF problem. It may help to restart the OSPF process.
Error Message%ROUTING-OSPF-4-REDIST_MAX_PFX Redistribution prefix limit has been reached - [dec] prefixes
Explanation We have reached the maximum number of redistributed prefixes
Recommended Action Check if redistribution of large number of prefixes is desired and has not been wrongly configured.
Error Message%ROUTING-OSPF-4-REDIST_THR_PFX Redistribution prefix threshold has been reached - [dec] prefixes
Explanation We have reached the threshold level of number of redistributed prefixes.
Recommended Action Check if redistribution of large number of prefixes is desired and has not been wrongly configured.
Error Message%ROUTING-OSPF-4-STUB_ASBR Router is currently an ASBR while having only one area which is a stub area
Explanation Router is configured as an ASBR but is only connected to a single stub area. This can waste resources since the router has nowhere to send the external LSAs that it is generating.
Recommended Action Check configuration and disable redistribution of routes into ospf if appropriate.
Error Message%ROUTING-OSPF-4-USING_OLD_RTRID OSPF process [chars] encountered an error while finding a new router ID. The old router ID [chars] is being used as an interim value. clear ip ospf process will force another attempt to find a valid router ID.
Explanation OSPF failed while attempting to allocate a router ID from the IP address of one of its interfaces due to an unexpected internal problem.
Recommended Action Use 'clear ip ospf process' to force another attempt to find a valid router ID. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-VIRTUAL_IN_NON_BACKBONE Virtual link information found in non-backbone area: [chars]
Explanation An internal error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-5-ADJCHG Process [chars], Nbr [chars] on [chars] from [chars] to [chars], [chars]
Explanation An OSPF neighbor has changed state. The message describes the change and the reason for it. This message appears only if the log-adjacency-changes command is configured for the OSPF process.
Recommended Action No action is required.
Error Message%ROUTING-OSPF-6-BADCHKSUM Checksum Failure in database in area [chars] Link State Id [chars] Old Checksum [hex] New Checksum [hex]
Explanation OSPF has detected a checksum error in the database due to memory corruption.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-6-DBEXIST area [chars] lsid [chars] mask [chars] adv [chars] type [dec]
Explanation OSPF has a problem locating the LSA, which could lead to a memory leak.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-6-GRACEFUL_SHUTDOWN [chars]
Explanation Informs user of graceful shutdown events. User needs to be aware of these activities.
Recommended Action No action required.
Error Message%ROUTING-OSPF-6-MAXMETRIC_RUNNING Current max-metric on-startup timer is running. New timer will be used at next reload.
Explanation maximum-metric LSA origination setting was changed while the maximum-metric origination was still active. The change will not take effect until the next time the system is restarted.
Recommended Action No action is required.
Error Message%ROUTING-OSPF-6-MEM_NOTIF [chars] [chars].
Explanation An unexpected event from the system monitor was seen.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-6-MGDTIMER External Managed Timer error, [chars], error [chars] [[hex]]
Explanation An external managed timer support routine failed. The affect this error has on the proper operation of OSPF depends on where and when this error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-6-NEWLIMIT [chars] limit changed. Old: [dec] New: [dec]
Explanation User has changed the configuable resource limit.
Recommended Action No action required. This is an informational message.
Error Message%ROUTING-OSPF-6-NOTREDIST3 build_ex_route(): don't redistribute net [chars]/[dec], [chars] advertises it already
Explanation For information only. Another router with a greater router ID is advertising the same external LSA. This router will stop originating the LSA to eliminate the redundancy.
Recommended Action No action is required.
Error Message%ROUTING-OSPF-6-REFBW_CHG Reference bandwidth is changed. Please ensure reference bandwidth is consistent across all routers.
Explanation Informational message reminding the user that reference bandwidth should be consistent across all routers in the area.
Recommended Action No action is required.
Error Message%ROUTING-OSPF-6-USING_MSGDGST Message-digest is used when both it and cleartext password are configured
Explanation Inform user that when both a clear text password and message-digest key are configured the message-digest key will be used.
Recommended Action No action is required.
Error Message%ROUTING-OSPF-7-DB_EX_DQUEUE [chars]: Unexpected external ReadyQ count of 0, &db=[hex], &rtr=[hex]
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-7-DB_READY_Q InReadyQ flag set for external DB, db [chars] on rtr_rt [chars]
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-7-DLINK dld [chars] is NULL
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-7-DQUEUE Double link queue count is 0 before decrement, &queue=[hex]
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-7-ERR_TUNNEL_INT TE IDB error, [chars], [chars] error [chars] [[hex]]
Explanation Error in creating a tunnel interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
OSPFv3_EDM Messages
Error Message%ROUTING-OSPFv3_EDM-3-DATALIST_ADD_FAILED Failed to add an external data manager datalist for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The attempt to add an item to an external data manager datalist has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-DATALIST_CREATE_FAILED Failed to create external data manager datalist for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The creation of the external data manager datalist has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-EDMINIT Error initializing EDM thread: [chars]: [chars]
Explanation An error occurred during initialization of the EDM thread.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-ENCODE_FAILED Failed to encode [chars] data in external data manager
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The data requested could not be encoded.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-EVENT_REGISTRATION_FAILED Failed to connect to the event manager: [chars]
Explanation The process failed while attempting to connect to an event manager channel for the indicated subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-LIST_ADD_FAILED Failed to add to an external data manager list for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The attempt to add an item to an external data manager list has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-LIST_CREATE_FAILED Failed to create external data manager list for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The creation of the external data manager list has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-NO_DATA Data for [chars] is not available
Explanation The data needed for the specified OSPF show command was not available. This would occur for non-critical data such as trace or debug information.
Recommended Action No action is required.
Error Message%ROUTING-OSPFv3_EDM-3-PROTO_REG_FAILED Failed to register show protocol information : [hex], '[chars]'
Explanation OSPFv3 was unable to register for support of the show protocol command.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-REGISTER_FAILED Failed to register its [chars] external data manager, '[chars]'
Explanation The process failed when attempting to register its external data manager with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-SYSDB_BIND_FAILED Failed to connect to SysDB ([chars])
Explanation The process failed to connect to SysDB while starting the indicated subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-SYSDB_COID_FAILED Failed to convert during a conn to coid conversion
Explanation The process failed to convert a conn to a coid while starting the indicated subsystem. This generally can only occur when starting up.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-6-BAGREG_FAILED Failed to register its external data manager data blocks
Explanation The process failed while attempting to register its external data manager data blocks with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
OSPFV3_POLICY Messages
Error Message%ROUTING-OSPFV3_POLICY-3-ORA_INSTBUILD Failed to build [chars], reason [chars] cer [chars]
Explanation Internal error in policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFV3_POLICY-3-ORA_RUN Could not apply policy operation [chars] to attribute [chars] because [chars]
Explanation Internal error in policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
OSPFv3_RIB Messages
Error Message%ROUTING-OSPFv3_RIB-2-NO_MEMORY Unable to allocate space for rib batching buffer: No Memory
Explanation Insufficent memory to allocate buffer for RIB batching API'
Recommended Action This indicates a low memory condition. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-OSPFv3_RIB-3-BIND Unable to bind to the RIB
Explanation An error occurred on a request to bind to the RIB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-DEFAULT_REG Unable to register with the RIB to receive the default route: [chars]
Explanation An error occurred on a request to have the RIB send us route updates for the default route.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-DISCONNECT Error while disconnecting RIB Event connection
Explanation An error occurred during an attempt to tear down the RIB Event connnection.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-ERR_BATCH_COMPLETE Error informing rib that batch is complete
Explanation An error was encountered in the call to ipv6_rib_batch_buffer_complete.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-ERR_PATH_ADD Error adding path-add to batching buffer (#[hex])
Explanation An error was encountered in the call to ipv6_rib_batch_add_path.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-ERR_PATH_DELETE Error adding path-delete to batching buffer ([hex])
Explanation An error was encountered in the call to ipv6_rib_batch_delete_path.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-ERR_ROUTE_HDR Error adding route header to batching buffer for [chars]/[dec] ([hex])
Explanation An error was encountered in the call to ipv6_rib_batch_add_route.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-ERR_UPDATE_COMPLETE Error informing rib that update is complete: [chars]
Explanation An error was encountered in the call to ipv6_rib_update_complete.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-FINDPDB Unable to get a RIB handle for [chars] routes: [chars]
Explanation An error occurred on a request to find the handle for the specified type of routes.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-PURGE Error removing OSPFv3 routes from the IPv6 RIB: [chars]
Explanation An error was encountered in the call to ipv6_rib_purge_protocol.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-REDIST_REG Unable to register with the RIB to receive updates for [chars] routes: [chars]
Explanation An error occurred on a request to have the RIB send us route updates for the specified type of routes.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-REGISTER Unable to register OSPFv3 with the RIB: [chars]
Explanation An error occurred on a request to register the OSPFv3 protocol with the RIB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
OSPFv3_UV Messages
Error Message%ROUTING-OSPFv3_UV-3-CERR_REG_FAIL Failed to register internal error codes: [chars]
Explanation An error occurred during the registration of OSPFv3 error codes.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-ERR_DBG_REGISTER_FAILED Error initializing ospfv3_uv debugging: [chars]
Explanation An error occurred during initialization of the ospfv3_uv process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-ERR_MEM_ALLOC_FAIL Unable to allocate [unsigned int] bytes for '[chars]'
Explanation The ospfv3_uv process was unable to allocate memory for the specified resource.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-ERR_PROC_READY Error signaling process ready: [chars]
Explanation The ospfv3_uv process was unable to signal process ready to sysmgr.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-ERR_SYSDB_CONNECT Error binding to SysDB: [chars]
Explanation The ospfv3_uv process was unable to bind to SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-ERR_SYSDB_DISCONNECT Error unbinding from SysDB: [chars]
Explanation The ospfv3_uv process was unable to unbind from SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-ERR_SYSDB_REG_VERIFY Error registering with SysDB: [chars]
Explanation The ospfv3_uv process was unable to register with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-ERR_VRFN_FNS_INIT Error setting SysDB callback functions: [chars]
Explanation The ospfv3_uv process was unable to initialize SysDB callbacks.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-EVENT_ERR Error in event loop: [chars]
Explanation An error occurred in the main ospfv3_uv event loop.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-EVM_CRE_FAIL Error creating event connection manager: [chars]
Explanation The ospfv3_uv process was unable to create an event connection manager instance.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-INTF_FWS_INIT Error initializing forward-reference store: [chars]
Explanation The ospfv3_uv process was unable to initialize the forward-reference store library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-6-PROCESS_NAME Caution: The OSPFv3 process name [chars] conflicts with a show or clear command name
Explanation The name chosen for the OSPFv3 process matches an ospf show or clear command, or a command abbreviation. This can cause ambiguities with subsequent show or clear commands for this process.
Recommended Action Choose a different name for the OSPFv3 process.
OSPFv3 Messages
Error Message%ROUTING-OSPFv3-2-NOMEMORY No memory for [chars]
Explanation The requested operation could not be accomplished because of a low memory condition.
Recommended Action This indicates a low memory condition. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-OSPFv3-3-ACL_GET Unable to get prefix-list [chars]: [chars]
Explanation An error occurred when trying to get the named prefix-list.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-ACL_REG Unable to register prefix-list [chars]: [chars]
Explanation An error occurred when trying to register for changes to the named prefix-list.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-ALLOCFAIL [chars] allocation failed: [chars]
Explanation Allocation of the specified resource failed, probably due to low memory.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-APIERR Call to [chars] from [chars] returns: [chars]
Explanation A lower-level support function returned an unexpected status.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-BADMSG Router thread received an invalid message type: [dec]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-BADTIMER Unrecognized [chars] timer type [dec]
Explanation A timer was found with an unrecognized type
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-CERR_REGISTER Failed to register internal error codes: [chars]
Explanation An error occurred during the registration of OSPFv3 error codes.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-CONN_FAIL Unable to connect to server [chars] : [chars]
Explanation OSPFv3 was unable to open a connection to a server. This is an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-DBGINIT Debug event initialization failed: [chars]
Explanation Unable to initialize a debugging flag.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-DBGREG Debug registration failed: [chars]
Explanation Unable to initialize debugging flags. Debug commands will not function.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-DELVLINK Cannot delete virtual link, backbone is being deleted
Explanation The virtual link cannot be removed because OSPFv3 is in the process of deleting the backbone area. Try again later.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-DLINK dld [chars] is NULL
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-DUP_RTRID Detected duplicate router ID [chars] from [chars] on interface [chars]
Explanation OSPFv3 received hello packet from a neighbor which has the same router ID as this routing process. A full adjacency cannot be established.
Recommended Action OSPFv3 router ID must be unique. Change the router ID.
Error Message%ROUTING-OSPFv3-3-DUP_RTRID_AREA Detected router with duplicate router ID [chars] in area [chars]
Explanation OSPFv3 has received multiple router LSAs with our router ID.
Recommended Action OSPFv3 router ID must be unique. Change the router ID.
Error Message%ROUTING-OSPFv3-3-DUP_RTRID_AS Detected router with duplicate router ID [chars] in inter-area router LSA advertised by [chars]
Explanation OSPFv3 has received an inter-area router LSA with our router ID.
Recommended Action OSPFv3 router ID must be unique. Change the router ID.
Error Message%ROUTING-OSPFv3-3-EVENTBLOCK Event blocking error in [chars] thread: [chars]
Explanation An error occurred while a thread was blocked waiting for an event
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-EVM_FD Error obtaining the [chars] file descriptor: [chars]
Explanation A call to get the file descriptor associated with an event manager connection failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-EVM_RETRY Unable to set event manager retry values for the [chars] connection: [chars]
Explanation A call to the external event manager to set connection retry values failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-FRIS_INSERT Unable to insert interface [chars] in the forward reference list: [chars]
Explanation An error occurred when adding the interface to the forward-reference list.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-HELLOINIT Error initializing hello thread: [chars]: [chars]
Explanation An error occurred during initialization of the hello thread.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IFINDEX_GET Unable to get interface index for [chars]: [chars]
Explanation An error occurred when trying to get a numeric interface index value for the specified interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IFINIT Initialization failure for interface [chars]
Explanation OSPFv3 failed to initialize data structures for an interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IFMGR [chars] failed: [chars]
Explanation The specified interface manager request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IFMGR_IF [chars] failed for interface [chars]: [chars]
Explanation The specified interface manager request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-INIT Initialization failed [[chars]], process terminated
Explanation An error occurred during initialization, causing the OSPFv3 process to terminate.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-INSTALL_REG Unable to register for package installation notifications: [chars]
Explanation An error occurred when trying to register with the packaging subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-INSTALL_UNREG Unable to unregister for package installation notifications: [chars]
Explanation An error occurred when trying to unregister with the packaging subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-INTERNALERR Internal error: [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IPARM [chars] failed: [chars]
Explanation The specified IP/ARM request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IPARM_IF [chars] failed for interface [chars]: [chars]
Explanation The specified IP/ARM request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IPSEC_CLOSE Error terminating IPSec processing for interface [chars]: [chars]
Explanation An error occurred when trying to close an IPSec SA for the named interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IPSEC_DEBUG_INIT Unable to initialize ipsec debugging: [chars]
Explanation An error occurred when trying to initialize the ipsec debug commands.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IPSEC_INIT Error initializing IPSec support: [chars]%s
Explanation An error occurred when trying to initialize the OSPFv3 IPSec subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IPSEC_OPEN Error initiating IPSec processing for interface [chars]: [chars]
Explanation An error occurred when trying to open an IPSec SA for the named interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-LAS [chars] failed: [chars]
Explanation The specified Local Address Service request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-LAS_ADDR Interface [chars] does not have a link-local address assigned
Explanation The specified interface has not received a link-local address from the Local Address Service.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-LAS_IF [chars] failed for interface [chars]: [chars]
Explanation The specified Local Address Service request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-MCAST Multicast [chars] on [chars] failed: [chars]
Explanation The specified multicast operation failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-MEM_ALLOC_FAIL Unable to allocate [unsigned int] bytes for '[chars]'
Explanation OSPFv3 was unable to allocate memory for the specified resource.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-MUTEX_INIT Error [chars] for [chars] mutex: [dec]
Explanation A error occurred in the initialization of the primitives used for thread synchronization. This is most likely a system error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-NO_VL_ENDPOINT Unable to add host route for virtual link endpoint in area [chars]
Explanation No IPv6 address was available to use as an endpoint for a virtual link.
Recommended Action Configure a loopback interface with an IPv6 address and add it to the specified area.
Error Message%ROUTING-OSPFv3-3-NOBACKBONE Flagged as being an ABR without a backbone area
Explanation The router was flagged as an Area Border Router (ABR) without backbone area in the router.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-NOSELF Interface [chars] if_state [dec]
Explanation An internal error occurred. An interface was not fully initialized when an OSPFv3 related event occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-NOTNBRTYPE Cannot configure neighbor on [chars]: interface must be NBMA or P2MP
Explanation Neighbor cannot be configured on interface if it is not type NBMA or point to multipoint.
Recommended Action No action is required.
Error Message%ROUTING-OSPFv3-3-PKTDROP Packet dropped: [chars]
Explanation An input packet was dropped for the specified reason.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-PKTDROP_STR Packet dropped: [chars]: [chars]
Explanation An input packet was dropped for the specified reason.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-PROCINIT Error initializing OSPFv3 process: [chars]: [chars]
Explanation An error occurred during OSPFv3 process initialization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-RIB [chars] [chars]/[dec]: [chars]
Explanation An error occurred on a request to the RIB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-RTRINIT Error initializing router thread: [chars]: [chars]
Explanation An error occurred during initialization of the router thread.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-SOCKET Socket operation [chars] failed: [chars]
Explanation The specified socket operation failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-SYSDB SysDB error: [chars]([chars]): [chars]
Explanation An error occurred when accessing the system database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-SYSMGR [chars] failed: [chars]
Explanation An specified system manager request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-THREAD_CREATE Error starting [chars] thread: [dec]
Explanation OSPFv3 failed to create a thread essential to its operation. This is an internal error. An automatic restart of the OSPFv3 process was necessary to attempt recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-UCAST Unicast [chars] on [chars] failed: [chars]
Explanation The specified unicast filter operation failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-UNKNOWNSTATE Reached unknown state in neighbor state machine
Explanation An internal software error occurred. When processing and DBD packet, the neighbor was found to be in an indeterminate state.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-UNSUPPORTED_IFTYPE Unsupported interface type [chars]: [chars]
Explanation The interface type is not yet supported by OSPFv3.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-BADAREA Received invalid packet: Incorrect area number ([chars]) from [chars], [chars]
Explanation The system received an OSPFv3 packet with an area ID that does not match the area that the interface belongs to.
Recommended Action Check the OSPFv3 configuration of the receiver and the sender for inconsistency. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-BADLENGTH Received invalid packet: Incorrect length ([dec]) from [chars], [chars]
Explanation The system received an OSPFv3 packet with a length field of less than normal header size or inconsistent with the size of the IPv6 packet in which it arrived. This indicates an error in the sender of the packet.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-BADLSA Invalid LSA: [chars], Type [hex] LSID [unsigned int] from [chars], [chars], [chars]
Explanation The router received an invalid LSA. The cause is either memory corruption or unexpected behavior on a router.
Recommended Action Check both the sending and receiving routers for memory corruption. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-BADVERS Received invalid packet: Incorrect OSPF version ([dec]) from [chars], [chars]
Explanation The system received an OSPFv3 packet with an OSPF version field other than 3. This indicates an error in the sender of the packet.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-ERRRCV Received invalid packet: [chars] from [chars], [chars]
Explanation An invalid OSPFv3 packet was received. Details are included in the error message. The cause might be a misconfigured OSPFv3 or an internal error in the sender.
Recommended Action Check the OSPFv3 configuration of the receiver and the sender for inconsistency. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-LSDB_ERROR Database error: [chars], Type [hex] LSID [unsigned int] from [chars]
Explanation OSPFv3 detected an error with its link state database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-LTRACE_INIT Unable to initialize the ltrace buffer [chars]: [chars]
Explanation An error occurred when trying to create a buffer for tracing.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-NONEIGHBOR Received [chars] from unknown neighbor [chars] on [chars]
Explanation OSPFv3 hello, database description, or database request packet was received, but the router could not identify the sender. This is a normal occurrance if a link flap occurs on the router receiving the packet.
Recommended Action This situation should correct itself. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-NORTRID OSPFv3 process [chars] could not pick a router-id, please configure manually
Explanation OSPFv3 failed while attempting to allocate a router ID.
Recommended Action Use the 'router-id' command to specify a unique Router ID for this OSPFv3 process.
Error Message%ROUTING-OSPFv3-4-POLICYCONFIG An error was encountered configuring policy, [chars]: [chars]
Explanation A problem was encountered while setting up route policy configuration. Some of the routing policy may not have been configured correctly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-REDIST_MAX_PFX Redistribution prefix limit has been reached - [dec] prefixes
Explanation We have reached the maximum number of redistributed prefixes
Recommended Action Check if redistribution of large number of prefixes is desired and has not been wrongly configured.
Error Message%ROUTING-OSPFv3-4-REDIST_THR_PFX Redistribution prefix warning threshold has been reached - [dec] prefixes
Explanation We have reached the warning threshold number of redistributed prefixes.
Recommended Action Check if redistribution of large number of prefixes is desired and has not been wrongly configured
Error Message%ROUTING-OSPFv3-4-STUB_ASBR Router is currently an ASBR while having only one area which is a stub area
Explanation Router is configured as an ASBR but is only connected to a single stub area. This can waste resources since the router has nowhere to send the external LSAs that it is generating.
Recommended Action Check configuration and disable redistribution of routes into OSPFv3 if appropriate.
Error Message%ROUTING-OSPFv3-4-USING_OLD_RTRID OSPFv3 process [chars] encountered an error while finding a new router ID. The old router ID [chars] is being used as an interim value.
Explanation OSPFv3 failed while attempting to allocate a router ID from the IPv4 address of one of its interfaces due to an unexpected internal problem.
Recommended Action Use 'clear ospfv3 process' to force another attempt to find a valid router ID. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-VIRTUAL_IN_NON_BACKBONE Virtual link information found in non-backbone area: [chars]
Explanation An internal error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-5-ADJCHG Process [chars], Nbr [chars] on [chars] from [chars] to [chars], [chars]
Explanation An OSPFv3 neighbor has changed state. The message describes the change and the reason for it. This message appears only if the log-adjacency-changes command is configured for the OSPFv3 process.
Recommended Action No action is required.
Error Message%ROUTING-OSPFv3-6-AREA_DELETE Area [chars] is being deleted, please try later
Explanation The configuration command could not be accepted because OSPFv3 is in the process of deleting the specified area. Try again later.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-6-AREACREATE Error creating area [chars]: [chars]
Explanation An error was encountered when trying to create an area.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-6-BADCHKSUM Checksum Failure in database: area [chars] LSA type [hex] LSID [hex] adv rtr [chars]: Old Checksum [hex] New Checksum [hex]
Explanation OSPFv3 has detected a checksum error in the database due to memory corruption.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-6-REFBW_CHG Reference bandwidth is changed. Please ensure reference bandwidth is consistent across all routers.
Explanation Informational message reminding the user that reference bandwidth should be consistent across all routers in the area.
Recommended Action No action is required.
PCL_EDM Messages
Error Message%ROUTING-PCL_EDM-2-SETUP Library initialization was unable to instrument EDM space because: [chars]
Explanation The library was unable to setup the EDM system access. This is a fatal logic error in the policy client library that will prevent any policy execution.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_EDM-3-INVALID_EDM_LIST Invalid EDM list type: [dec]. Must be get:[dec], list:[dec] or datalist: [dec]
Explanation There was an internal logic error in the EDM list management software that resulted in a request for an unknown data type.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_EDM-3-REG_FAIL Failed to register policy EDM. Some policy-related 'show' commands may not work. (stage [dec], reason: [chars])
Explanation An failure occurred while attempting to publish the management information for this process. The process will continue to run, and the error will not affect its operation, but some 'show' commands may fail with an error.
Recommended Action Please capture the output of: sh proc location (where is each RP, DRP etc) sh sysdb reg edm shared-plane sh tech-support Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
PCL_EE Messages
Error Message%ROUTING-PCL_EE-2-COPY_OF_MEMORY The transport notification could not allocate memory for item: [chars]
Explanation The new policy copy to scratch area failed due to a lack of memory. Because this was in a sysdb notification, we are unable to return an error and can not track recovery. The policy will default to a 'drop all' mode of operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_EE-2-FAILED_SPACE Unable to make space for arguments on field [chars], oper [chars] on [chars] because: [chars]
Explanation The system was unable to allocate argument spaces for the above reason. Because of this, the policy will not be actived.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_EE-2-FAILED_XML_COMPILE The XML parser failed to compile [chars] because [chars]
Explanation The XML parser was unable to compile this policy. Because this was in a sysdb notification, we are unable to return an error and can not track recovery. The policy will default to a 'drop all' mode of operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_EE-2-LINK_FAILED The linker failed to link [chars] because [chars]
Explanation The tree linker was unable to link this policy. Because this was in a sysdb notification, we are unable to return an error and can not track recovery. The policy will default to a 'drop all' mode of operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_EE-3-ARG_COUNT_HIGH There were more arguments from repository than protocol understands at [dec]
Explanation The repository tried to access the nth (the number in the message) argument, but the protocol only supports one less than that.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_EE-3-ARG_COUNT_LOW There were fewer arguments from repository than protocol understands at [dec]
Explanation The repository tried to access the nth (the number in the message) argument, but the protocol only requires at least one more than that.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_EE-3-BT_COUNT_NOT_ONE Base type [chars]:[chars] returned [dec] copies, when only one should be possible
Explanation This is a direct logic error, since a given base type can only have one representation of itself at a given attach point.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_EE-3-FAILED_BUILD [chars] '[chars]' on field '[chars]' on '[chars]' failed to build instance because [chars]
Explanation A problem was encountered while attempting to compile the named policy for execution. This may be due to lack of memory, or due to a previously undetected error in the policy.
Recommended Action It may help to restart the Policy Repository process with proc restart policy_repository, or to modify the policy or policies that are applied by that policy. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-PCL_EE-3-FAILED_OPER_ARGS Internal error: [chars] '[chars]' on field '[chars]' on '[chars]' failed to return arguments: [chars]
Explanation An internal error was encountered while compiling a routing policy for execution. Policies in the specified process may fail to run correctly. This may be due to an out-of-memory condition, or to a software error.
Recommended Action It may help to restart the affected process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_EE-3-INVALID_ARGUMENT_TYPE The argument type (string, variable, or math) was none of these.
Explanation This is a theoretically impossible situations. The XML transport parsing code may have somehow setup an intermediate node incorrectly or this could indicate memory corruption.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_EE-3-INVALID_NODE_TYPE Invalid node type in compile tree walk of type: [dec]
Explanation A node type was found in the unlinked (xml) tree space that the execution linker did not know. This is most likely a logic error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_EE-3-INVALID_SRC_TYPE Internal error: invalid linked node type:[dec], branch ignored
Explanation A memory corruption error was detected in a routing policy in the named process. Routing policies in that process may not function correctly.
Recommended Action It may help to restart the affected process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_EE-3-INVALID_VARIABLE_NODE The variable node returned([dec]) was not a retriever([dec]) or cmp retiever([dec]).
Explanation This error indicates a coding error. It should not happen in the field and if it does indicates a need to contact support. The given policy will have been replaced in the engine with a strict drop.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_EE-3-MISMATCHED_BASE_TYPE The variable item had type [chars]:[chars] while the protocol indicates taking [chars]:[chars]
Explanation The protocol ora indicated that it would take one base type and version while the retriever being used returned a different one. The repository should have prevented this.
Recommended Action Possible version mismatch. Restart repository and protocol. If this does not correct the problem, contact support.
Error Message%ROUTING-PCL_EE-3-MISSING_OPER Missing [chars] '[chars]' on field '[chars]' on '[chars]' because [chars]
Explanation An attempt to fetch the given field/operator failed because of the shown error. If this is a 'not found' error, this will be a mismatch between what the repository thought the oras were capable of and what they actually were. I.E., most likely some type of version problem. If another type of error, the result will be less clean.
Recommended Action Check versions of protocols in repository and verify correctness and then restart the repository. If the problem persists, or the error was not a 'not found' event, check with support.
Error Message%ROUTING-PCL_EE-3-NO_SPACE_WITH_ARGS There are arguments, but no space was requested
Explanation This should not be possible, but this message indicates that this event has occured and has been caught.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_EE-3-WRONG_POLICY Policy [[chars]] tries to [[chars]] the [[chars]] attribute, which is not available at the [[chars]] attach point.
Explanation A show command specifying a route policy has been issued, but the route policy that was specified (or a policy applied by that policy) contained some operations that were not appropriate for that particular command.
Recommended Action Specify a different route policy that contains only operations suitable for the command in question. It may be helpful to use the show rpl policy detail to find where the policy uses the unsuitable operation.
Error Message%ROUTING-PCL_EE-4-DESTRUCTOR_FAILED [chars]%s failed at [chars].[chars] because [chars]
Explanation This should not be possible. The end result will be leaked memory during a policy free.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_EE-4-SUBWALK_FAILED Free time subwalk failed because [chars]
Explanation This should not be a possible message. The result of this will be a memory leak during a policy free.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_EE-4-TREE_BAD_MAGIC Possible corrupt data structure in policy
Explanation This indicates that some of the data structures used to store a policy may be corrupt. The process will attempt to continue running, but it is possible that further problems may occur, in which case the process should be restarted when convenient.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_EE-4-UNCAUGHT_EXCEPTION There was an uncaught exception: [chars], node type=[chars], field=[chars], oper=[chars], info=[chars]
Explanation An error occurred while the execution of a run time policy node. For qft2 time frame the node is skipped. This message and behavior will change with the exception enhancements.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_EE-4-UNEXPECTED_ERROR The error [chars] occurred while removing a compiled tree from its list
Explanation The should not occur in an operational system and may indicate memory corruption or logic error. The result is not critical by itself, but may indicate other problems.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_EE-4-UNKNOWN_SUBFIELD The policy subfield [chars] changed on policy [chars] but is unknown to pcl
Explanation A notification occurred for a sub-node the pcl did not understand. This is likely the result of a version difference between the repository and this instance of the pcl and should not cause any harm.
Recommended Action Check version of repository and pcl and check release notes to see if this combination is legal.
PCL_LOCKING Messages
Error Message%ROUTING-PCL_LOCKING-3-event_failure [chars]: Failure ([chars]) trying to [chars]
Explanation Locking event failed. Failure will be passed back to calling system.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
PCL_ORA Messages
Error Message%ROUTING-PCL_ORA-3-FAILED_MATH_BUILD The ora init was unable to build math: where = '[chars]' why='[chars]'
Explanation This is a fatal build of the ORA math information. Since the ORA is a static view of the pcl space, this should rarely show up outside of active development. If this shows up in the field, it is most likely a resource issue.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_ORA-3-FAILED_ORA_BUILD The ora init was unable to build ORA: where = '[chars]' why='[chars]'
Explanation This is a fatal build of the ORA information. Since the ORA is a static view of the pcl space, this should rarely show up outside of active development. If this shows up in the field, it is most likely a resource issue.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_ORA-3-INVALID_ARG_SIZE The base type '[chars]' in '[chars]' got an arg space of size [dec] but it needed [dec]
Explanation The pcl infrastructure handed an argument space that was sized differently from what the function expected. This may be the result of a version mismatch, but is most likely a logic error.
Recommended Action Check versions of components and call support they are correct.
Error Message%ROUTING-PCL_ORA-3-INVALID_ARG_SPACE The base type '[chars]' in '[chars]' was given a NULL argument space pointer
Explanation The pcl infrastructure handed a NULL argument space to the function. This should not be possible and almost certainly a logic error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_ORA-4-CERRNO Unable to register cerrno dll because: [chars]
Explanation ORA dll was unable to register cerrno dll. This is non-fatal, but implies that errno value from this library will not be printed as cleanly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
PCL_USE Messages
Error Message%ROUTING-PCL_USE-3-APMATH Attach point [chars] failed math merge because [chars]. AP unusable.
Explanation The given attach point used math abilities that were not found in the AP context. This is most likely a coding error, but could possibly be caused by a revision mismatch between the publishing protocol and the PCL.
Recommended Action Check for version mismatch. If that is not the problem, contact support.
Error Message%ROUTING-PCL_USE-3-DBGINIT Unable to bring up debug event structures: [chars]
Explanation The debug event initialization failed. The pcl will still run correctly, but debug commands may be unavailable.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_USE-3-USEFREED Attach Point use was not in use array: index=[dec] on [chars] because [chars]
Explanation Internal logic error in policy client library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_USE-4-AP_FREE Attach point '[chars]'([dec]) failed because [chars].
Explanation Something went wrong during an attach point destroy. Since this is usually done during a protocol restart, the system should still be operative. However, this does indicate some problem had occured in the data structure for the attach point instance.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_USE-4-BAD_DELETE The policy '[chars]' was just 0 count, but no entry was found in tree because [chars]
Explanation The given policy reference went completely to zero. However, the attempt to remove the policy from the list of policies the pcl is watching failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_USE-4-CERR_REG Unable to register cerrno dll for cerrno printing: [chars]
Explanation When the library attempted to publish itself as a cerrno string source it failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_USE-4-ENGINE_FREE Attach point [chars] failed engine data cleanup because [chars].
Explanation Something went wrong during an attach point destroy. Since this is usually done during a protocol restart, the system should still be operative. However, this does indicate some problem had occured in the data structure for the attach point instance.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_USE-4-FREE_FROM_LIST Attach point [chars] would not detach from internal list index [dec] because [chars]
Explanation Something went wrong during an attach point destroy. Since this is usually done during a protocol restart, the system should still be operative. However, this does indicate some problem had occured in the data structure for the attach point instance.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_USE-4-INSTANCE_FREE Attach point instance [dec] free on attach point [chars] failed because [chars].
Explanation Something went wrong during an attach point destroy. Since this is usually done during a protocol restart, the system should still be operative. However, this does indicate some problem had occured in the data structure for the attach point instance.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_USE-4-MATH_FREE Attach point attach point [chars] free failed during [chars] math cleanup because [chars].
Explanation Something went wrong during an attach point destroy. Since this is usually done during a protocol restart, the system should still be operative. However, this does indicate some problem had occured in the data structure for the attach point instance.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_USE-4-MISSING_DEREF The policy '[chars]' was just dereferenced, but no such policy was in storage.
Explanation An internal pcl logic error was noticed when a policy was dereferenced, but no such policy was located in the internal storage area. While no direct damage occurred, the missing policy may indicate a possible hidden problem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_USE-4-NMATH_FREE Attach point [chars] failed merged math cleanup because [chars].
Explanation Something went wrong during an attach point destroy. Since this is usually done during a protocol restart, the system should still be operative. However, this does indicate some problem had occured in the data structure for the attach point instance.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_USE-4-NULL_CHANGE NULL change callback on use of policy [chars]
Explanation Protocol does not support dynamic changing of policy. This is allowed during protocol development, but is considered a bug for shipping product.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_USE-4-SINK_DUPLICATE_FAILED Unable to duplicate route for EDM request on sink side because: [chars]
Explanation The protocol was unable to provide a duplicate route for an EDM request. This is often due to memory exhaustion problems and does not harm normal policy execution in any way, but may cause a broken show command or similar operation.
Recommended Action Retry problem operation and if problem persists, call support.
Error Message%ROUTING-PCL_USE-4-SOURCE_DUPLICATE_FAILED Unable to duplicate route for EDM request on source side because: [chars]
Explanation The protocol was unable to provide a duplicate route for an EDM request. This is often due to memory exhaustion problems and does not harm normal policy execution in any way, but may cause a broken show command or similar operation.
Recommended Action Retry problem operation and if problem persists, call support.
Error Message%ROUTING-PCL_USE-4-UNDOCK Attach point attach point [chars] free failed during [chars] undocking because [chars].
Explanation Something went wrong during an attach point destroy. Since this is usually done during a protocol restart, the system should still be operative. However, this does indicate some problem had occured in the data structure for the attach point instance.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
PCL_XML Messages
Error Message%ROUTING-PCL_XML-3-BAD_CURRENT_NODE_TYPE XML parser in indeterminate state: name=[chars], state=[dec]
Explanation A logic error has occurred within the XML parser that has resulted in the parse ending up in an unpredicted state.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_XML-3-BAD_REFERENCE XML parser saw reference to id '[chars]' which was not in tree.
Explanation The compiled policy in XML format referenced another node which was not located in policy block. This is most likely a repository error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_XML-3-UNKNOWN_NODE_TYPE xml being linked has a node type that is not supported: [dec] at [dec]
Explanation Internal logic error in policy client library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_XML-4-BAD_NEW_NODE_TYPE xml item '[chars]' with id '[chars]' on new element
Explanation XML data from repository had an unexpected element. There may be a version mismatch between the repository and this version of the pcl.
Recommended Action Check repository and protocol instances for version compatibility and try restarting the repository and protocol. If problem persists, call support.
Error Message%ROUTING-PCL_XML-4-BAD_PLACEMENT XML parser saw unsupported '[chars]' as ora placement on node [chars]
Explanation XML data from repository had an unexpected element. There may be a version mismatch between the repository and this version of the pcl.
Recommended Action Check repository and protocol instances for version compatibility and try restarting the repository and protocol. If problem persists, call support.
Error Message%ROUTING-PCL_XML-4-BAD_RESULT XML saw invalid exit node result '[chars]' on [chars]. Should be 'drop' or 'pass'
Explanation XML data from repository had an unexpected element. There may be a version mismatch between the repository and this version of the pcl.
Recommended Action Check repository and protocol instances for version compatibility and try restarting the repository and protocol. If problem persists, call support.
Error Message%ROUTING-PCL_XML-4-ELEMENT_DATA_AFTER_END Saw cdata in xml after the last element ended. Data = '[chars]'
Explanation There was cdata (character data) after the closing of the last element in the XML document. This is a program error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_XML-4-ELEMENT_END_AFTER_END Saw an end element for [chars] after XML end
Explanation There was an element end that occured after the last possible xml element end.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_XML-4-EXTRA_CDATA There was more than one set of cdata in the elment. State=[chars], cdata2='[chars]'
Explanation There was more than one set of cdata (character data) in the element. This is a program error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_XML-4-INVALID_CRE_NAME XML in 'compare retriever' node block had an invalid element name:[chars]
Explanation XML data from repository had an unexpected element. There may be a version mismatch between the repository and this version of the pcl.
Recommended Action Check repository and protocol instances for version compatibility and try restarting the repository and protocol. If problem persists, call support.
Error Message%ROUTING-PCL_XML-4-INVALID_EXIT_NAME XML in 'exit' node block had an invalid element name:[chars]
Explanation XML data from repository had an unexpected element. There may be a version mismatch between the repository and this version of the pcl.
Recommended Action Check repository and protocol instances for version compatibility and try restarting the repository and protocol. If problem persists, call support.
Error Message%ROUTING-PCL_XML-4-INVALID_IF_NAME XML in 'if' node block had an invalid element name:[chars]
Explanation XML data from repository had an unexpected element. There may be a version mismatch.
Recommended Action Check repository and protocol instances for version compatibility and try restarting the repository and protocol. If problem persists, call support.
Error Message%ROUTING-PCL_XML-4-INVALID_IFLIST_NAME XML in 'iflist' node block had an invalid element name:[chars]
Explanation XML data from repository had an unexpected element. There may be a version mismatch between the repository and this version of the pcl.
Recommended Action Check repository and protocol instances for version compatibility and try restarting the repository and protocol. If problem persists, call support.
Error Message%ROUTING-PCL_XML-4-INVALID_INSTANCE_CNT xml item '[chars]' was seen [dec] times, with valid limits of [unsigned int] to [unsigned int].
Explanation The given XML element occured outside the limiting number of times allowed for it. For example, it may be required and did not appear, or may have shown up twice while only being allowed once. There may be a version mismatch between the repository and this version of the pcl.
Recommended Action Check repository and protocol instances for version compatibility and try restarting the repository. If problem persists, call support.
Error Message%ROUTING-PCL_XML-4-INVALID_LOCATION_NAME xml location name block had invalid element name:[chars]
Explanation XML data from repository had an unexpected element. There may be a version mismatch between the repository and this version of the pcl.
Recommended Action Check repository and protocol instances for version compatibility and try restarting the repository and protocol. If problem persists, call support.
Error Message%ROUTING-PCL_XML-4-INVALID_RE_NAME XML in 'retriever' node block had an invalid element name:[chars]
Explanation XML data from repository had an unexpected element. There may be a version mismatch between the repository and this version of the pcl.
Recommended Action Check repository and protocol instances for version compatibility and try restarting the repository and protocol. If problem persists, call support.
Error Message%ROUTING-PCL_XML-4-INVALID_SA_NAME XML in 'simple action' node block had an invalid element name:[chars]
Explanation XML data from repository had an unexpected element. There may be a version mismatch between the repository and this version of the pcl.
Recommended Action Check repository and protocol instances for version compatibility and try restarting the repository and protocol. If problem persists, call support.
Error Message%ROUTING-PCL_XML-4-MISMATCHED_END Saw close on element [chars] while in element [chars].
Explanation A closer to a given element was noted that did not match the element that was being processed. This indicates malformed XML and is a program error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_XML-4-MULTIPLE_NODES There was more than one ([dec]) node defined at this level ([chars]) in the XML
Explanation There was a node choice in the XML, but more than node was defined at this point. This violates the schema and is a program error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_XML-4-NO_NODE There was no node defined at this level ([chars]) in the XML
Explanation There was a node choice in the XML, but no node was defined at this point. This violates the schema and is a program error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_XML-4-TOO_MANY_ARG_TYPES A given argument had more than one type of argument in it
Explanation A argument can either be a string, variable, or math set. In this case, more than one was set. This is a program error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_XML-4-TRAILING_ELEMENT Saw element '[chars]' after root node completed
Explanation There was another element after the end of document. This is a program error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_XML-4-UNKNOWN_ELEMENT There was an element '[chars]' of unknown type in state '[chars]'
Explanation There was an element specified in the XML transport that did not exist in the list of possible types.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_XML-4-UNKNOWN_MARKER Mark node result marker set to an unknown mode of '[chars]'.
Explanation The marker value for a mark node was set to an unknown value. Valid entries are: 'set', and 'clear'. This is a program error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_XML-4-UNKNOWN_PLACEMENT Field placement set to unknown ora placement of '[chars]'
Explanation The placement value for this field was set to an unknown value. Valid entries are: 'srcRoute', 'sinkRoute', 'srcProtocol', 'sinkProtocol', 'globalProtocol' or 'pcl'. This is a program error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_XML-4-UNKNOWN_RESULT Exit node result status set to an unknown result of '[chars]'.
Explanation The result value for an exit node was set to an unknown value. Valid entries are: 'pass', and 'drop'. This is a program error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-PCL_XML-4-WRONG_ATTR_COUNT xml item '[chars]' has incorrect number([dec]) of attributes: range is [dec] to [dec]
Explanation XML data has wrong number of attributes. There may be a version mismatch between the repository and this version of the pcl.
Recommended Action Check repository and protocol instances for version compatibility and try restarting the repository. If problem persists, call support.
POLICY_REPOSITORY_EDM Messages
Error Message%ROUTING-POLICY_REPOSITORY_EDM-3-DATA_GENERATION_FAILED Failed to generate [chars] data in external data manager
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The data requested could not be generated.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_EDM-3-DATALIST_ADD_FAILED Failed to add an external data manager datalist for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The attempt to add an item to an external data manager datalist has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_EDM-3-DATALIST_CREATE_FAILED Failed to create external data manager datalist for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The creation of the external data manager datalist has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_EDM-3-ENCODE_FAILED Failed to encode [chars] data in external data manager
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The data requested could not be encoded.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_EDM-3-EVENT_REGISTRATION_FAILED Failed to connect to the event manager: [chars]
Explanation The process failed while attempting to connect to an event manager channel for the indicated subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_EDM-3-LIST_ADD_FAILED Failed to add to an external data manager list for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The attempt to add an item to an external data manager list has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_EDM-3-LIST_CREATE_FAILED Failed to create external data manager list for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The creation of the external data manager list has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_EDM-3-REGISTER_FAILED Failed to register its external data manager
Explanation The process failed when attempting to register its external data manager with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_EDM-3-SYSDB_BIND_FAILED Failed to connect to SysDB ([chars])
Explanation The process failed to connect to SysDB while starting the indicated subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_EDM-3-SYSDB_UNBIND_FAILED Failed to unconnect to SysDB ([chars])
Explanation The process failed to disconnect from SysDB before starting the indicated subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.