-
Cisco IOS XR System Error Message Reference Guide, Release 3.2
-
Preface
-
Cisco IOS XR System Error Messages Overview
-
Access Control List (ACL) Error Messages for Cisco IOS XR
-
Fabric (FABRIC) Error Messages for Cisco IOS XR
-
Hardware Accessibility (HA) Messages for Cisco IOS XR
-
Installation (INSTALL) Messages for Cisco IOS XR
-
Internet Protocol (IP) Messages for Cisco IOS XR
-
Layer 2 (L2) Messages for Cisco IOS XR
-
Media (MEDIA) Messages on Cisco IOS XR
-
Manageability (MGBL) Messages for Cisco IOS XR
-
Operating System (OS) Messages for Cisco IOS XR
-
Packet Infrastructure (PKT_INFRA) Messages for Cisco IOS XR
-
Platform (PLATFORM) Messages for Cisco IOS XR
-
Quality of Service (QOS) Messages for Cisco IOS XR
-
Routing (ROUTING) Messages for Cisco IOS XR
-
Security (SECURITY) Messages for Cisco IOS XR
-
Simple Network Management Protocol (SNMP) Messages for Cisco IOS XR
-
System Database (SYSDB) Messages for Cisco IOS XR
-
Feedback
Table Of Contents
Quality of Service (QoS) Messages
Quality of Service (QoS) Messages
This section contains all Quality of Service related System Error Messages. The following facility codes are represented in this module:
CLASSIFY Messages
Error Message%QOS-CLASSIFY-3-NOT_SUPPORTED Too many classes: Maximum 16 classes are supported
Explanation Maximum of 16 classes is supported in a policy.
Recommended Action Reduce the number of classes or contact cisco *support* for enhancement of the feature.
Error Message%QOS-CLASSIFY-4-DEBUG_INIT_ERROR A error occurred during debug initialization, err: [chars]
Explanation The Classify QoSMgr component encoutered an error during debug initialization
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
FQ_QOS Messages
Error Message%QOS-FQ_QOS-2-CAPS_ADD_FAIL Cannot add FQ component in data plane. Error code - [chars]
Explanation Failed to add FQ component in data plane
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-FQ_QOS-2-CAPS_LOOKUP_FAIL Cannot find FQ component in data plane[chars]. Error code - [chars]
Explanation Failed to find FQ component in data plane
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-FQ_QOS-2-CAPS_REMOVE_FAIL Cannot remove FQ component in data plane. Error code - [chars]
Explanation Failed to remove FQ component in data plane
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-FQ_QOS-2-DIST_DATA_PATH_CONTROL_FAIL Failed to send control message to Linecards [chars]
Explanation Could not send control message to Linecards
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-FQ_QOS-2-FT_ALREADY_EXIST Congestion management feature already exist.
Explanation Congestion management feature already exist
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-FQ_QOS-2-MALLOC_FAIL Memory alloc error [chars]
Explanation The router cannot allocate more memory %s.
Recommended Action It may be necessary to free some memory by exiting a program.
Error Message%QOS-FQ_QOS-2-MIN_BW_ERROR Minimum bandwidth is more than the shape bandwidth
Explanation Minimum bandwidth is less than the shape bandwidth.
Recommended Action Correct the configuration so that minimum bandwidth is less than the shape(maximum) bandwidth.
Error Message%QOS-FQ_QOS-2-MTU_QUERY_FAIL Cannot retrieve MTU. Error code - [chars]
Explanation Failed to retrieve MTU
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-FQ_QOS-2-NO_L1_BW_ERROR Level1 has no bandwidth guarantee. So cannot have level2 bandwidth guarantee.
Explanation Level1 has no bandwidth guarantee. So cannot have level2 bandwidth guarantee.
Recommended Action Correct the configuration so that level1 has a bandwidth guarantee.
Error Message%QOS-FQ_QOS-2-PRIORITY_ERROR Shaping and Priority can not be configured under the same class
Explanation Shape and priority can not be configured under the same class.
Recommended Action Remove one of the feature.
Error Message%QOS-FQ_QOS-2-SHAPE_BW_EXCEED Shape bandwidth exceeds 100 percent of the interface bandwidth
Explanation Shape bandwidth is more than the interface bandwidth
Recommended Action Correct the configuration so that shape bandwidth is less or equal to the interface bandwidth.
Error Message%QOS-FQ_QOS-2-TUPLE_UNPACK_FAIL Failed to unpack configuration data.
Explanation Could not unpack configuration data
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-FQ_QOS-2-WM_PTR_FAIL [chars] TXM Watermark was not found.
Explanation Failed to find TXM watermark
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-FQ_QOS-3-BUNDLE_BW_NOPCT Absolute bw specified for bundle interfaces, use percentage values instead
Explanation For bundle interfaces, percentage values must be used
Recommended Action Use percentage vaules instead of absolute bandwidth values
Error Message%QOS-FQ_QOS-3-SYSDB_ERR SysDB connection error [chars]. Error code - [chars]
Explanation SysDB connection error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-FQ_QOS-4-BW_EXCEED Sum of allocated bandwidth [chars] exceeds the maximum
Explanation Sum of reserved bandwidth in the policymap exceeds the maximum.
Recommended Action Correct the policymap so that the sum of reserved bandwidth is smaller than the maximum.
Error Message%QOS-FQ_QOS-4-CLASSES_EXCEED_MAX_CLASSES Number of classes exceeds the maximum number of classes allowed
Explanation Number of configured classes exceeds the maximum number of classes allowed
Recommended Action Reduce the number of configured classes within the policymap.
Error Message%QOS-FQ_QOS-4-DEBUG_INIT_ERROR A error occurred during debug initialization, err: [chars]
Explanation The QoS FIFO Netio component encoutered an error during debug initialization
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-FQ_QOS-4-DUPLICATE_COS Found duplicate cos values [chars].
Explanation Duplicate cos values are not allowed
Recommended Action Remove duplicate cos values from the policymap
Error Message%QOS-FQ_QOS-4-NO_BW_LEFT No bandwidth left for unmatched traffic
Explanation No bandwidth left for unconfigured default class
Recommended Action Correct the policymap so that bandwidth is available for default class
Error Message%QOS-FQ_QOS-4-PCN_FAIL PCN contact failed. [chars].
Explanation PCN contact failed. %s.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-FQ_QOS-4-PRIORITY_ALREADY_ASSIGNED Priority is already assigned to another class. Type = [hex]
Explanation Priority is already assigned to another class.
Recommended Action Do not configure more than two classes as priority class.
Error Message%QOS-FQ_QOS-4-QUEUE_LIMIT_EXCEED Configured queue limit exceeds the maximum allowed, [dec]
Explanation Configured queue limit is larger than the maximum allowed
Recommended Action Correct the policymap so that queue limit does not exceed the maximum allowed
MARK_QOS Messages
Error Message%QOS-MARK_QOS-3-NOT_SUPPORTED Marking of [chars] on egress interface not supported
Explanation Marking of given attribute is not supported.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-MARK_QOS-4-DEBUG_INIT_ERROR A error occurred during debug initialization, err: [chars]
Explanation The Mark QoSMgr component encoutered an error during debug initialization
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MDRR Messages
Error Message%QOS-MDRR-4-TOO_MANY_CLASSES Number of classes configured in the policymap exceeds the maximum number of queues allowed by the MDRR node
Explanation Number of configured classes is larger than the number of queues allowed.
Recommended Action Reduced the number of classes configured in the policymap.
QALLOC Messages
Error Message%QOS-QALLOC-3-ALLOC_BLOCK_ERROR [chars]
Explanation An error has occurred while dealing with blocks on the allocated list.
Recommended Action File a DDTS
Error Message%QOS-QALLOC-3-COALESCE_ERROR Error Coalescing free queues
Explanation An error has occurred while coalescing free queues
Recommended Action File a DDTS
Error Message%QOS-QALLOC-3-ERROR QoSRM-Err: [chars]
Explanation This is an error message from the QoS RM Process, it indicates that something has gone wrong internally in the QoS RM.
Recommended Action File a DDTS
Error Message%QOS-QALLOC-3-FREE_BLOCK_ERROR [chars]
Explanation An error has occurred while dealing with blocks on the free list.
Recommended Action File a DDTS
Error Message%QOS-QALLOC-3-QUEUE_SANITY Queue value out of bounds ([chars]) Queue: [unsigned int]
Explanation Queue bounds checking has detected an error with a queue value
Recommended Action File a DDTS
Error Message%QOS-QALLOC-4-WARN QoSRM-Warn: [chars]
Explanation This is a warning message from the QoS RM Process
Recommended Action *RECUR*
Error Message%QOS-QALLOC-6-INFO QoSRM-Info: [chars]
Explanation This is an informational message from the QoS RM Process
Recommended Action *RECUR*
Error Message%QOS-QALLOC-7-DEBUG QoSRM-Debug: [chars]
Explanation This is a debuging message from the QoS RM Process
Recommended Action *NONE*
QOS_CLASSIFY_NETIO Messages
Error Message%QOS-QOS_CLASSIFY_NETIO-4-DEBUG_INIT_ERROR A error occurred during debug initialization, err: [chars]
Explanation The QoS Classify Netio component encoutered an error during debug initialization
Recommended Action *SUPPORT*
QOS_FIFO Messages
Error Message%QOS-QOS_FIFO-4-DEBUG_INIT_ERROR A error occurred during debug initialization, err: [chars]
Explanation The QoS FIFO Netio component encoutered an error during debug initialization
Recommended Action *SUPPORT*
Error Message%QOS-QOS_FIFO-4-DEBUG_INIT_ERROR A error occurred during debug initialization, err: [chars]
Explanation The FIFO QoSMgr component encoutered an error during debug initialization
Recommended Action *SUPPORT*
QOS_RC_QOSMGR Messages
Error Message%QOS-QOS_RC_QOSMGR-3-RC_BUNDLE_BW_NOPCT Absolute bw specified for bundle interfaces, use percentage values instead
Explanation For bundle interfaces, percentage values must be used
Recommended Action Use percentage vaules instead of absolute bandwidth values
Error Message%QOS-QOS_RC_QOSMGR-4-DEBUG_INIT_ERROR A error occurred during debug initialization, err: [chars]
Explanation The rc QoSMgr component encoutered an error during debug initialization
Recommended Action *SUPPORT*
Error Message%QOS-QOS_RC_QOSMGR-4-RC_BW_EXCEED Policer rate exceeds 100 percent of the interface bandwidth
Explanation The Policer rate in the policymap exceeds the maximum.
Recommended Action Correct the policymap so that the Policer rate is smaller than the maximum.
QOS_TXM Messages
Error Message%QOS-QOS_TXM-4-DEBUG_INIT_ERROR A error occurred during debug initialization, err: [chars]
Explanation The QoS TXM Netio component encoutered an error during debug initialization
Recommended Action *SUPPORT*
Error Message%QOS-QOS_TXM-4-DEBUG_INIT_ERROR A error occurred during debug initialization, err: [chars]
Explanation The TXM QoSMgr component encoutered an error during debug initialization
Recommended Action *SUPPORT*
QOS_WRED Messages
Error Message%QOS-QOS_WRED-4-DEBUG_INIT_ERROR A error occurred during debug initialization, err: [chars]
Explanation The WRED QoSMgr component encoutered an error during debug initialization
Recommended Action *SUPPORT*
QOS Messages
Error Message%QOS-QOS-2-MALLOC_FAIL Memory alloc error [chars] [chars]
Explanation The router cannot allocate more memory.
Recommended Action It may be necessary to free some memory by exiting a program.
Error Message%QOS-QOS-2-MALLOC_FAIL Memory alloc error [chars] [chars]
Explanation The router cannot allocate more memory.
Recommended Action It may be necessary to free some memory by exiting a program.
Error Message%QOS-QOS-2-MALLOC_FAIL Memory alloc error [chars] [chars]
Explanation The router cannot allocate more memory.
Recommended Action It may be necessary to free some memory by exiting a program.
Error Message%QOS-QOS-2-MALLOC_FAIL2 Memory alloc error [chars] [hex]
Explanation The router cannot allocate more memory.
Recommended Action It may be necessary to free some memory by exiting a program.
Error Message%QOS-QOS-3-ASYNC_ATTACH_EVENT Failed to attach handler for async events: [chars]
Explanation Failed to attach handler for async events.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-BACKENDSCAN_FAIL Could not read configuration. Error code - [chars]
Explanation Backend_scan failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-BW_BUNDLE_ABSOLUTE Absolute values cannot be used for policies configured on Bundle interfaces. Use percentage values instead
Explanation This is a fatal condition.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-BW_SUM_EXCEEDS_100_PC Sum of bandwidth allocated to all classes exceeds 100 percent. Allocated BW : [dec] percent
Explanation This is a fatal condition.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-CHECKPT_ERR Checkpoint error - [chars]. Error code - [chars]
Explanation Checkpoint error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-CLASSMAP_CREATE_FAIL Error in creating class-map '[chars]': [chars]
Explanation Error encountered in creating a new class-map.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-CLASSMAP_NOT_CONFIGURED Classp map not configured for [chars]
Explanation Classp map could not be configured.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-CONNECT_FAIL Server connection failed - [chars]. Error code - [chars]
Explanation Connection to some server failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-CONNECT_FAIL Server connection failed - [chars]. Error code - [chars]
Explanation Connection to some server failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-CTRL_STR_NOT_FOUND Feature [chars] not found [chars]
Explanation The specified feafure is unknown.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-DATA_SERVER_BIND_FAIL Data server binding error. Error code - [chars]
Explanation Data server binding failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-DEBUG_FAIL Error occurred while registering for debugging services
Explanation Error occurred while waiting for an event.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-DEBUG_FAIL Error occurred while registering for debugging services
Explanation Error occurred while waiting for an event.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-DEBUG_INIT_FAIL Could not register for debug.
Explanation Registration for debug failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-DEF_CLASS_BW_EXCEED_99_PC Sum of bandwidth allocated to non-default classes exceeds 99 percent- Allocated BW : [dec] percent
Explanation This is a fatal condition.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-DLL_CLOSE_FAIL Closing [chars] feature dll control function failed
Explanation Closing feature dll control function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-DLL_LOAD_FAIL DLL loading failure [chars] Error code - [chars]
Explanation Loading of DLL failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-DLL_REFCOUNT_ZERO Attempting to remove [chars] when the feature is not loaded
Explanation DLL ref count is zero.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-ERR_BAG_REGISTER Failed to register bag structures with bag server (Reason: [chars])
Explanation The process could not register the data structures used by QoS statistics and management agents.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-EVENT_CONN_ERR Error in [chars]: [chars]
Explanation Error encountered in opening connection to a required server.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-EVM_CREATE_FAIL Failed to create event manager
Explanation Failed to create event manager.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-EVM_CREATE_FAIL Failed to create event manager
Explanation Failed to create event manager.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-EVM_CREATE_FAIL Failed to create event manager
Explanation Failed to create event manager.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-FEATURE_ADD_FAIL policy = [chars], class = [chars], feature = [chars].
Explanation Feature instance already exists under a class instance when we tried to add it. This should never happen because we handle 'modify' case(feature already exists but parameters changed) before calling 'add' case.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-FEATURE_MODIFY_FAIL policy = [chars], class = [chars], feature = [chars].
Explanation Modification of an existing feature failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-FILE_ERROR File [chars] [chars]
Explanation The file is corrupted or missing information.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-FILE_OPEN_ERROR File open error - could not open [chars]
Explanation File open failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-FILE_WRONG_INFO File [chars] [chars] [dec]
Explanation The file has wrong information.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-FT_CONFIGURE_FAIL Failed to configure [chars] feature [chars]. Error code - [chars]
Explanation Failed to configure feature.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-FT_LOOKUP_FAIL Feature lookup failed for feature_type [dec] feature_id [dec].
Explanation Feature lookup failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-FT_REMOVE_FAIL Failed to remove the feature type. [chars] Error code - [chars]
Explanation Failed to remove the feature type.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-FT_SEND_FAIL Sending control to [chars] feature failed
Explanation Sending control to feature failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-GO_ACTIVE Failed to transition to active role: [chars]
Explanation Failed to transition to active role.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-HPOLICY_ATTACH_FAIL Too Many levels of heirarchy in policy [chars].
Explanation Policy could not be installed because of too many levels of heirarchy.
Recommended Action Remove one level of heirarchy.
Error Message%QOS-QOS-3-IF_CLEANUP_FAIL Interface cleanup failed for [hex]. Error code - [chars]
Explanation Interface cleanup failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-IF_D_LOOKUP_FAIL Lookup failed for default features for interface [hex]. Error code - [chars]
Explanation Lookup failed for default QOS features.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-IF_LOOKUP_FAIL Interface lookup failed for [chars]. Error code - [chars]
Explanation Interface lookup failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-IF_NOT_FOUND Interface not found in the table for [hex]
Explanation Interface counld not be found in the table.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-IM_CONNECT_FAIL Interface control server connection failed - [chars]. Error code - [chars]
Explanation Connection to interface manager failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-IM_ERR Interface Manager connection error
Explanation Interface Manager connection error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-IM_FAIL Interface control server message handling failed - [chars]. Error code - [chars]
Explanation Interface control server message handling failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-IM_FAIL_UNEXPECTED Unexpected im msg opcode ([hex])
Explanation Unexpected im msg opcode received.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-LC_CONNECT_FAIL Unable to connect to linecard [chars]
Explanation Connection to line card failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-LC_FAIL Cannot run QOS managers on linecards
Explanation Unable to run QOS managers on linecards.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-LC_MSG_SEND_FAIL Unable to send message[chars]. Error code - [chars]
Explanation Sending message failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-LTRACE_INIT_FAIL Could not register for tracing.
Explanation Registration for tracing failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-MGR_DLL_INIT_FAIL Could not initialize [chars] dll. Error code - [chars]
Explanation Could not get feature manager DLL init function.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-MGR_DLL_LOAD_FAIL Loading feature [chars] dll failed
Explanation Loading of feature manager DLL failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-MGR_DLL_OPEN_FAIL Could not open [chars] DLL. Error code - [chars]
Explanation Could not open feature DLL.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-MGR_DLL_REGISTER_CERR_FAIL Could not register error codes for [chars] dll. Error code - [chars]
Explanation Could not get register DLL error codes.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-MSG_GET_CHAN_RENDEZVOUS Failed to get channel rendezvous name from LWM: [chars]
Explanation Failed to get channel rendezvous name from LWM.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-MSG_SEND_FAIL Failed to send message to feature [chars] [chars]. Error code - [chars]
Explanation Failed to send message to feature.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-NO_DEFAULT_QUEUE_ERR Setting default queueing feature failed [chars]. Error code - [chars]
Explanation Setting default queueing feature failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-NO_FT_CONTROL_BLOCK feature control block could not be found. [chars]
Explanation Unable to find feature control block.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-NODE_INSTL_FAIL Could not install [chars] feature
Explanation Installation of feature dll failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-OVER_SUBSCRIPTION_OF_MIN_BW_GAURANTEES There is oversubscription of minimum bandwidth guarantees - taking into account HP bandwidth. Bandwidth guarantees may not be met for this policy Allocated BW : [dec] percent
Explanation This is a fatal condition.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-OVL_INIT_FAIL Error in initializating environment variables - [chars], [chars]
Explanation Initializating environment variables failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-OVL_RGST_FAIL Could not register environment variables. Error code - [chars]
Explanation Registeration of environment variables failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-PACKAGE_NOT_REMOVED Package not fully removed - [chars] [chars]
Explanation Package was not fully removed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-POLICY_ATTACH_FAIL Service policy [chars] could not be attached to [chars]. Error code - [chars]
Explanation Policy could not be installed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-POLICY_INSTALL_FAIL Policy could not be installed [chars] [chars] Error code - [chars]
Explanation Policy could not be installed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-POLICY_MODIFY_FAIL Modified policy-map [chars] could not be attached. Error code - [chars]
Explanation Modified policy-map has a wrong configuration.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-POLICY_NOT_FOUND Policy not found - [chars] [chars]
Explanation Could not find the specified policy name.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-POLICY_REMOVE_FAIL Service policy [chars] could not be removed. Error code - [chars]
Explanation Policy could not be removed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-QFIFO_DEBUG_NETIO_INIT_FAIL Failed to Initialize debug netion - [chars] Error : [chars]
Explanation This is a fatal condition.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-QFIFO_SHOW_INT_INFO_FAIL Show FIFO init info Failed - [chars] Error : [chars]
Explanation This is a fatal condition.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-QSM_ADD_SERVICE Failed to publish message channel using QSM: [chars]
Explanation Failed to publish message channel using QSM.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-RP_CONNECT_FAIL Unable to connect to Route Processor. Error code - [chars]
Explanation Connection to Route Processor failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-RPC_FAIL RPC failure - [chars]
Explanation RPC failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-SHOW_FAIL Show command failed - [chars]
Explanation Show command failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-SVC_REGISTER_FAIL Service register failed - [chars]
Explanation Service register failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-SYSDB_BIND_ERR SysDB binding error. Error code - [chars]
Explanation SysDB binding failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-SYSDB_ERR SysDB connection error [chars]. Error code - [chars]
Explanation SysDB connection error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-SYSMGR_GET_NODE_STATE Failed to get card role from sysmgr: [chars]
Explanation Failed to get card role from sysmgr.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-SYSMGR_REGISTER_NODE_STATE_CHANGE Failed to register with sysmgr for card role changes: [chars]
Explanation Failed to register with sysmgr for card role changes.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-THREAD_CRT_FAIL Could not spawn qos thread
Explanation Creating qos thread failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-UNSUPPORTED_MIN_BW_CONFIG Bandwidth command is not supported on the ingress side. Invalid Configuration
Explanation We do not support bandwidth command on ingress policies. You can configure 'bandwidth remaining' to assign weights for the different queues.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-UNSUPPORTED_Q_LIMIT_CONFIG In order to configure queue-limit for a class, you need to configure atleast one feature that allocates a separate queue for that class
Explanation If you configure queue-limit command for a class, then that class requires a separate queue (due to h/w implementation). Since the user has not configured any feature for this class that allocates a separate queue for that class, the user is not allowed to configure queue-limit for that class.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-WAIT_ERR Error occurred while waiting for an event
Explanation Error occurred while waiting for an event.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-WAIT_ERR Error occurred while waiting for an event
Explanation Error occurred while waiting for an event.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-3-WAIT_ERR Error occurred while waiting for an event
Explanation Error occurred while waiting for an event.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-4-FT_ALREADY_EXIST Found already-existing feature [chars] [hex]
Explanation The specified feature already exists.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-4-POLICY_ALREADY_EXIST Found already-existing policy map [chars] [chars]
Explanation The specified policy map already exists.
Recommended Action Try a different policy name.
Error Message%QOS-QOS-7-ENS_ERROR ENS Debug:[chars] rc=[chars]
Explanation ENS related functionality failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-7-NETIO_GET_PAK_DEST_SPONGEQ_FAIL Failed to get packet destination SPONGQ - [chars] Error : [chars]
Explanation This is a fatal condition.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-7-NETIO_SET_PAK_DEST_SPONGEQ_FAIL Failed to set packet destination SPONGQ - [chars] Error : [chars]
Explanation This is a fatal condition.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-7-NETIO_SET_PAK_SHAPEQ_FAIL Failed to set packet shape Q - [chars] Error : [chars]
Explanation This is a fatal condition.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-7-NETIO_SET_PAK_SHARQ_FAIL Failed to mark the default sharq queue - [chars] Error : [chars]
Explanation This is a fatal condition.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%QOS-QOS-7-NETIO_SET_PAK_VITAL_BIT_FAIL Failed to set packet vital bit - [chars] Error : [chars]
Explanation This is a fatal condition.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
QOSEA Messages
Error Message%QOS-QOSEA-3-ERROR QoSEA-Err: [chars]
Explanation This is an error message from the QoS EA Process, it indicates that something has gone wrong internally in the QoS EA.
Recommended Action File a DDTS
Error Message%QOS-QOSEA-3-MSG_CHAN Could not create Msg chan: [chars] error: [chars]
Explanation The QoS EA could not create the necessary message channel due to the given error
Recommended Action *DDTS*
Error Message%QOS-QOSEA-3-MSG_HANDLER_ERR An error occurred in the [chars] message handler
Explanation An error occurred during message handling in the indicated message handler
Recommended Action File a DDTS
Error Message%QOS-QOSEA-3-POLICY_ERROR QoSEA-Err: class:[chars], [chars]
Explanation This is an error message from the QoS EA Process, it indicates that something has gone wrong while trying to configure a service policy.
Recommended Action *NONE*
Error Message%QOS-QOSEA-3-UNHANDLED_MSG The QoS EA received an unhandled message
Explanation The QoS EA received a message that it was unable to handle'
Recommended Action *DDTS*
Error Message%QOS-QOSEA-3-UNKNOWN_MSG An unknown message was dispatched to the [chars] message handler: Msg: [hex]
Explanation An incoming message was demuxed to the incorrect message handler
Recommended Action File a DDTS
Error Message%QOS-QOSEA-4-WARN QoSEA-Warn: [chars]
Explanation This is a warning message from the QoS EA Process
Recommended Action *RECUR*
Error Message%QOS-QOSEA-5-NOTICE QoSEA-Notice: [chars]
Explanation This is a notice message from the QoS EA Process
Recommended Action *NONE*
Error Message%QOS-QOSEA-6-INFO QoSEA-Info: [chars]
Explanation This is an informational message from the QoS EA Process
Recommended Action *RECUR*
Error Message%QOS-QOSEA-6-MSG_ASYNC An Asynchronous message was received
Explanation The QoS EA received an asynchronous message.
Recommended Action *NONE*
Error Message%QOS-QOSEA-6-POLICY_INFO QoSEA-Info: class:[chars], [chars]
Explanation This is an informational message from the QoS EA Process. It indicates that something can not be configure in service policy.
Recommended Action *NONE*
Error Message%QOS-QOSEA-7-DEBUG QoSEA-Debug: [chars]
Explanation This is a debuging message from the QoS EA Process
Recommended Action *NONE*
QOSRM Messages
Error Message%QOS-QOSRM-3-ERROR QoSRM-Err: [chars]
Explanation This is an error message from the QoS RM Process, it indicates that something has gone wrong internally in the QoS RM.
Recommended Action File a DDTS
Error Message%QOS-QOSRM-3-MSG_CHAN Could not create Msg chan: [chars] error: [chars]
Explanation The QoS RM could not create the necessary message channel due to the given error
Recommended Action *DDTS*
Error Message%QOS-QOSRM-3-MSG_HANDLER_ERR An error ([chars]) occurred in the [chars] message handler,Msg:[hex]
Explanation An error occurred during message handling in the indicated message handler
Recommended Action File a DDTS
Error Message%QOS-QOSRM-3-UNHANDLED_MSG The QoS RM received an unhandled message
Explanation The QoS RM received a message that it was unable to handle'
Recommended Action *DDTS*
Error Message%QOS-QOSRM-3-UNKNOWN_MSG An unknown message was dispatched to the [chars] message handler: Msg: [hex]
Explanation An incoming message was demuxed to the incorrect message handler
Recommended Action File a DDTS
Error Message%QOS-QOSRM-3-UNKNOWN_QTYPE Unknown Q-Type in message: [hex]
Explanation The QoS RM received a message, but was unable to determine which resource the message was intended for because the Q-Type field was incorrect.
Recommended Action File a DDTS
Error Message%QOS-QOSRM-4-WARN QoSRM-Warn: [chars]
Explanation This is a warning message from the QoS RM Process
Recommended Action *RECUR*
Error Message%QOS-QOSRM-6-INFO QoSRM-Info: [chars]
Explanation This is an informational message from the QoS RM Process
Recommended Action *RECUR*
Error Message%QOS-QOSRM-6-MSG_ASYNC An Asynchronous message was received
Explanation The QoS RM received an asynchronous message.
Recommended Action *NONE*
Error Message%QOS-QOSRM-7-DEBUG QoSRM-Debug: [chars]
Explanation This is a debuging message from the QoS RM Process
Recommended Action *NONE*
