-
Cisco IOS XR System Error Message Reference Guide, Release 3.2
-
Preface
-
Cisco IOS XR System Error Messages Overview
-
Access Control List (ACL) Error Messages for Cisco IOS XR
-
Fabric (FABRIC) Error Messages for Cisco IOS XR
-
Hardware Accessibility (HA) Messages for Cisco IOS XR
-
Installation (INSTALL) Messages for Cisco IOS XR
-
Internet Protocol (IP) Messages for Cisco IOS XR
-
Layer 2 (L2) Messages for Cisco IOS XR
-
Media (MEDIA) Messages on Cisco IOS XR
-
Manageability (MGBL) Messages for Cisco IOS XR
-
Operating System (OS) Messages for Cisco IOS XR
-
Packet Infrastructure (PKT_INFRA) Messages for Cisco IOS XR
-
Platform (PLATFORM) Messages for Cisco IOS XR
-
Quality of Service (QOS) Messages for Cisco IOS XR
-
Routing (ROUTING) Messages for Cisco IOS XR
-
Security (SECURITY) Messages for Cisco IOS XR
-
Simple Network Management Protocol (SNMP) Messages for Cisco IOS XR
-
System Database (SYSDB) Messages for Cisco IOS XR
-
Feedback
Table Of Contents
Internet Protocol (IP) Messages
Internet Protocol (IP) Messages
This section contains all Internet Protocol related System Error Messages. The following facility codes are represented in this module:
ARP Messages
Error Message%IP-ARP-1-ERR_DLSYM dlsym failed for symbol [chars]
Explanation dlsym failed
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-2-ERR_EVM_CONN_CREATE Couldn't create the event manager connection:[chars]([chars])
Explanation Event connection did not succeed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-2-ERR_EVM_HANDLER_CREATE Couldn't create the event handler:[chars]([chars])
Explanation Event handler creation did not succeed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-2-ERR_EVM_MGR_CREATE Couldn't create the event manager:[chars]
Explanation Event Manager creation did not succeed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-2-ERR_EVM_QUEUE_SIZE Couldn't get queue_size, error = [chars]
Explanation Couldn't get the arp recv packet queue size
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-2-ERR_IMP_SERVER_BIND Couldn't bind to IMP server:[chars]([chars])
Explanation IMP server bind did not succeed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_ADDR_NOTIF_REG [chars]
Explanation sysdb addr notification registration failed
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_API_INIT [chars] ([dec], [chars])
Explanation An Init called failed, exiting ARP.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_ARP_CACHE_INCONSISTANT [chars] [chars] [chars] ([chars],[chars])
Explanation Inconsistancy because of a static/alias with ip exisiting on some interface
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_BAG_REGISTRATION_FAILED IP ARP failed to register the [chars] ([chars]) external data manager data blocks
Explanation ARP failed to register the BAG structure for EDM.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_BUNDLE [chars], ([dec], [chars])
Explanation A Bundle related call failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_CHUNK_CREATE Fatal Error: couldn't allocate chunk mem for arp packet queue
Explanation couldn't allocate chunk mem for arp packet queue
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_CONN Fatal Error: Couldn't create [chars] for [chars] interaction
Explanation A certain call to an event_conn_*() function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_DLL_SIGN Invalid dll signature on [chars]
Explanation DLL signature was invalid.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_DLOPEN dlopen of [chars] failed
Explanation dlopen call failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_EA [chars], ([dec], [chars])
Explanation An ARP EA related call failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_EDM_REGISTRY Failed to register with sysdb as EDM for [chars] ([chars])
Explanation Arp process could not register as and edm with sysdb.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_EDM_SYSDB_BIND Failed to bind to SysDB for EDM for [chars] ([chars])
Explanation Arp edm could not bind with sysdb.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_ENCAP_NOT_SUPP [chars]
Explanation An internal error has occured
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_ENS_INIT [chars] [chars]
Explanation Initialization to ENS by consumer/producer failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_EVM_ASYNC_ATTACH Fatal Error: event_async_attach failed for [chars], error = [chars]
Explanation event_async_attach failed
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_EVM_NULL Fatal Error: Couldn't create the event manager for [chars]
Explanation Couldn't create the event manager for arp recv thread
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_GET_MACADDR Failed to get MAC address for [chars]: Error = [chars]
Explanation im_attr_macaddr_get failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_GSP [chars], ([dec], [chars])
Explanation A GSP related call failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_IM [chars], ([dec], [chars])
Explanation A call to IM failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_IM_STATE_REG failed to register with IM for ipv4 caps state, number of attempts:[dec], ([dec], [chars])
Explanation Failed to register with IM for ipv4 caps state.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_IMP_REG_CONTROL_HANDLER Failed to register with imp control handler:[chars]([chars])
Explanation Could not register with the imp control handler.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_INIT [chars]
Explanation An Init called failed, exiting ARP.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_MACADDR_BAD_LENGTH Incorrect MAC address size for [chars] (returned: [dec], expected: [dec])
Explanation im_attr_macaddr_get returned bad length of macaddr.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_MACADDR_INVALID [chars]
Explanation Rejected 802.3/802.5 multicast addresses (MSB set).
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_MALLOC_FAIL Failed to allocate memory for incoming arp packet
Explanation Couldn't allocate memory for incoming arp pak. This is a generic malloc failure possibly the box is running low on memory.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_MEDIA [chars] [chars]
Explanation An Init called failed, exiting ARP.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_MEDIA_INIT [chars]
Explanation An Init called failed, exiting ARP.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_NRS_INIT [chars]
Explanation Initialization to NRS by consumer/producer failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_PAK_DEQUEUE Couldn't dequeue pak, error = [chars]
Explanation Couldn't dequeue packet in arp recv queue
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_PTHREAD_CREATE [chars], ([dec], [chars])
Explanation pthread create failed
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_REGEXP [chars]
Explanation Invalid regular expression.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_REMOVE_ENOENT Attempt to remove non-existant ARP entry ([chars])
Explanation An internal error has occured
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_RESOLV_BADSTATE Inconsistent ARP entry state ([hex]) for [chars]
Explanation An internal error has occured
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_SEM_WAIT ARP failed to wait on semaphore [chars], [chars]
Explanation ARP failed to wait on a semaphore, resulting in the ARP process restarting.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_SVC_REG [chars]
Explanation Call to svc_register failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_SYSDB [chars] failed: Error = [chars]
Explanation A certain call to sysdb failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_SYSMGR [chars], ([dec], [chars])
Explanation ARP registration with SysMgr failed in some way
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_TIMER_BADSTATE Timer expired for ARP entry ([chars]) in state ([hex])
Explanation An internal error has occured
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-3-ERR_WAIT Error occurred while waiting for an event
Explanation Error occurred while waiting for an event.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-6-ERR_AUX_INIT Failed to initialize aux node ([chars]).
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-6-ERR_DUPADDR Duplicate IP address [chars] on [chars], sourced by [chars]
Explanation Another system is using your IP address.
Recommended Action Change the IP address of one of the two systems.
Error Message%IP-ARP-6-ERR_DUPMAC Duplicate MAC address [chars]
Explanation ARP request received with dest MAC same as incoming interfaces MAC address.
Recommended Action Change the MAC address of one of the two systems.
Error Message%IP-ARP-6-ERR_HWADDR_INVALID Invalid hardware address [chars]
Explanation ARP packet received with an invalid layer 2 address length
Recommended Action Debug message only. No action is required.
Error Message%IP-ARP-6-ERR_IF_MISMATCH Selected outgoing interface for [chars] differs from incoming interface
Explanation An ARP packet was received from an unexpected interface. ' 'This can happen due to misconfiguration of the IP addresses on ' 'the intervenient systems or due to incorrect bridging configuration.
Recommended Action No action is required.
Error Message%IP-ARP-6-ERR_MEDIA_UNKNOWN Media type not known for [chars]
Explanation Media type is not known to control plane
Recommended Action No action is required.
Error Message%IP-ARP-6-ERR_NETIO_CONNECT Failed to initialize handler for netio connection [chars] ([chars])
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-ARP-6-ERR_OPCODE_UNKNOWN Unrecognized ARP opcode [dec]
Explanation ARP packet received with an unrecognized opcode
Recommended Action Debug message only. No action is required.
CE_TFTP Messages
Error Message%IP-CE_TFTP-3-DATA_SEND_ERR [chars]: Eror while sending data over Control Ethernet
Explanation Unable to send data over the control ethernet.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-CE_TFTP-3-FATAL_EXIT [CETFTP_SERVER]: CE-TFTP server process exiting because [chars]
Explanation The CE-TFTP server process exitted due to some reason
Recommended Action None.
Error Message%IP-CE_TFTP-3-FILE_ACCESS_ERR [CETFTP_SERVER]: The file [chars] could not be accessed because [chars]
Explanation The given file could not be accessed due to reasons specified.
Recommended Action None.
Error Message%IP-CE_TFTP-3-FILE_NOT_FOUND_ERR [CETFTP_SERVER]: File [chars] not found
Explanation The given file was not found at the specified path
Recommended Action Check the path of file specified for download
Error Message%IP-CE_TFTP-3-INVALID_FILENAME_ERR [CETFTP_SERVER]: The filename is invalid because [chars]
Explanation The given filename was invalid due to reasons specified.
Recommended Action None.
Error Message%IP-CE_TFTP-4-DEBUG_INIT_WARN [CETFTP_SERVER]: Unable to initialize debug space
Explanation The CE-TFTP server process was unable to initialize the debug space
Recommended Action None.
Error Message%IP-CE_TFTP-4-DEBUG_REG_WARN [CETFTP_SERVER]: Unable to register for debug services
Explanation The CE-TFTP server process was unable to register for debug services
Recommended Action None.
Error Message%IP-CE_TFTP-4-SYSDB_CFG_WARN [CETFTP_SERVER]: Unable to initialize config space
Explanation The CE-TFTP server process was unable to initialize the config space
Recommended Action None.
Error Message%IP-CE_TFTP-6-INVALID_PKT [[chars]]: [chars], dropping packet
Explanation Received an invalid packet.
Recommended Action None.
Error Message%IP-CE_TFTP-6-INVALID_PROTOCOL_FIELD [[chars]]: [chars] = [hex], dropping packet
Explanation Received an packet with an invalid protocol field.
Recommended Action None.
DOMAIN_SERVICES Messages
Error Message%IP-DOMAIN_SERVICES-3-ATTACH_HANDLER Failed to attach an [chars] handler: [chars]
Explanation The domain_services process failed to attach an event handler to receive event messages sent to it.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-DOMAIN_SERVICES-3-BIND_SYSDB Failed to connect to SysDB: [chars]
Explanation The domain_services process failed to bind to SysDB server.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-DOMAIN_SERVICES-3-CREATE_CHANNEL Failed to create a channel for [chars]
Explanation The domain_services process failed to create a channel so that other processes can send event messages to it.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-DOMAIN_SERVICES-3-CREATE_CHUNK Failed to allocate chunk memory for [chars]
Explanation The domain_services process failed to create chunk memory for its domain name, domain address and domain alias data structures.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-DOMAIN_SERVICES-3-CREATE_EVENT_CONN Failed to create a event connection structure: [chars]
Explanation The domain_services process failed to create and initialize an event connection structure. If the connection ever goes away, event connection manager will automatically tries to re-connect.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-DOMAIN_SERVICES-3-CREATE_TIMER [chars]: [chars]
Explanation The domain_services process failed to create and initialize its various managed timers.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-DOMAIN_SERVICES-3-EDM_SERVER [chars]: [chars]
Explanation Error in the domain edm server.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-DOMAIN_SERVICES-3-END_PROC Unexpected process termination: [chars]
Explanation The domain_services process was terminated unexpectedly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-DOMAIN_SERVICES-3-GET_COID Failed to get SysDB connection id: [chars]
Explanation The domain_services process failed to obtain the connection id for an SysDB event connection.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-DOMAIN_SERVICES-3-OPEN_EVENT_CONN Failed to open a event connection to [chars]: [chars]
Explanation The domain_services process failed to open a event connection.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-DOMAIN_SERVICES-3-REGISTER_DEBUG Failed to register for debugging events: [chars]
Explanation The domain_services process failed to register for notification of changes to the domain_services debug flag(s).
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-DOMAIN_SERVICES-3-REGISTER_EVM Failed to register handlers for SysDB events: [chars]
Explanation The domain_services process failed to register its verification and apply handlers for SysDB events.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-DOMAIN_SERVICES-3-REGISTER_RPC Failed to register for RPC service
Explanation The domain_services process failed to register its RPC server with the RPC portmapper.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-DOMAIN_SERVICES-3-SYSMGR_PROC_READY Domain services failed to notify the completion of init: [chars]
Explanation domain services failed to notify the compltetion of initialization
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-DOMAIN_SERVICES-7-REGISTER_CERRNO Failed to register process's specific error codes: [chars]
Explanation The domain_services process failed to register its specific cerrno codes and messages.
Recommended Action Debug message only. No action is required.
GSR_IPv4_hwdrv Messages
Error Message%IP-GSR_IPv4_hwdrv-3-RES_ERROR Error: [chars]: Err=[chars]
Explanation A error occurred in GSR Ipv4 Edge h/w Driver resulting in a failure to provide some system service as indicated in the message text.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-GSR_IPv4_hwdrv-6-INFO_MSG Info: [chars]
Explanation This is a Informational message in the GSR IPV4 Driver to indicate an operation.
Recommended Action No action is required.
GSR_IPv4 Messages
Error Message%IP-GSR_IPv4-3-RES_ERROR Error: [chars]: Err=[chars]
Explanation A error occurred in GSR Ipv4 Edge forwarding driver resulting in a failure to provide some system service as indicated in the message text.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-GSR_IPv4-4-exception [chars]
Explanation A SW exception of unexpected condition
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-GSR_IPv4-6-INFO_MSG Info: [chars]
Explanation This is a Informational message in the GSR IPV4 Driver to indicate an operation.
Recommended Action No action is required.
GSR_IPv6_FIB_EELC Messages
Error Message%IP-GSR_IPv6_FIB_EELC-3-ERROR gsr_eelc_ipv6_fib: error encountered, reason = [chars]
Explanation Error has occurred during the setup of the IPv6 FIB on the GSR EE LCs.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-GSR_IPv6_FIB_EELC-3-INFO gsr_eelc_ipv6_fib: informational msg, [chars]
Explanation The is an informational message.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
GSR_IPv6_hwdrv Messages
Error Message%IP-GSR_IPv6_hwdrv-3-RES_ERROR Error: [chars]: Err=[chars]
Explanation A error occurred in GSR Ipv6 Edge h/w Driver resulting in a failure to provide some system service as indicated in the message text.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-GSR_IPv6_hwdrv-6-INFO_MSG Info: [chars]
Explanation This is a Informational message in the GSR IPV6 Driver to indicate an operation.
Recommended Action No action is required.
HFR_IPv4 Messages
Error Message%IP-HFR_IPv4-2-BGP_PA_CONFIG BGP PA configuration failed due to lack of resources [chars]
Explanation FIB is not committing BGP PA configurations due to a low resource condition.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-HFR_IPv4-2-BGP_PA_CONFIG_IFH BGP PA configuration for ifh [hex], if: failed due to [chars]
Explanation FIB is not committing BGP PA configurations due to internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-HFR_IPv4-2-MSTATS_ALLOC_ERR Failed to alloc stats counter err [dec]: table [dec]
Explanation Unable to allocated needed stats counters, accounting features may not be working properly.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-HFR_IPv4-2-SYSTEM_FAIL [chars] [chars] (errno=[dec])
Explanation There was a critical system call failure resulting in a failure to provide some system service as indicated in the message text.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-HFR_IPv4-2-TRANS_ERR Failed to register transition handler
Explanation There was a critical system call failure resulting in a failure to provide some system service as indicated in the message text.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-HFR_IPv4-4-LTRACE Failed to initialize tracing - [chars]: [chars] (errno [hex])
Explanation There was a system call failure during initialization of the ltrace logging system. Ltrace logs may not be available.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-HFR_IPv4-4-TRANS_WARNING Failed to respond to transition request: [chars] (errno [hex])
Explanation There was a critical system call failure. System may not have handled certain transitions properly.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-HFR_IPv4-6-INFO [chars] [chars] (errno [hex])
Explanation There was an internal failure that may impact non-essential system function
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
IEP Messages
Error Message%IP-IEP-3-FAILED_INTERNAL_DAEMON Internal Error: call to function '[chars]' by iep daemon failed
Explanation An internal error has occurred which prevents the iep daemon from continuing.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IEP-3-INTERNAL_ERROR Call to [chars] from function [chars] returned error
Explanation An internal system error occured.
Recommended Action Debug message only. No action is required.
Error Message%IP-IEP-3-INTERNAL_ERROR2 Call to [chars] from function [chars] returned error: [chars]
Explanation An internal system error occured.
Recommended Action Debug message only. No action is required.
Error Message%IP-IEP-7-FAILED_SYSDB_DAEMON Call to '[chars]' from function '[chars]' returned error:'[chars]'
Explanation An error occurred while using SysDB.
Recommended Action Debug message only. No action is required.
Error Message%IP-IEP-7-FAILED_SYSDB_LIBRARY Call to '[chars]' from function '[chars]' returned error:'[chars]'
Explanation An error occurred while using SysDB.
Recommended Action Debug message only. No action is required.
IP_ARM_CLIB Messages
Error Message%IP-IP_ARM_CLIB-3-OPTION_DEPRECATED Option deprecated, please see EDCS- send a mail to q-ntwk-infra-dev.
Explanation Option deprecated, please see EDCS- send a mail to q-ntwk-infra-dev.
Recommended Action Option deprecated, please see EDCS- send a mail to q-ntwk-infra-dev.
Error Message%IP-IP_ARM_CLIB-3-UNNUM_BATCH_FAILED Failed to complete unnumbered interface processing for a batch ([chars]: [chars]), this process may have inconsistent IP address information for the unnumbered interfaces that have recently been changed
Explanation An internal error occurred (possibly due to a lack of resources) that prevented all recent unnumbered interface configuration changes from being processed by the specified process.
Recommended Action Repeat the recent configuration change and verify that the specified process is operating correctly. If this behaviour persists then check that there are enough resources available to run IP ARM or contact your technical support representative copying the error message exactly as it appears.
Error Message%IP-IP_ARM_CLIB-3-UNNUM_SINGLE_FAILED Failed to complete unnumbered interface processing for the interface '[chars]' ([chars]: [chars]), this process may have inconsistent IP address information for the unnumbered interfaces that have recently been changed
Explanation An internal error occurred (possibly due to a lack of resources) that prevented a single unnumbered interfaces configuration change from being processed by the specified process.
Recommended Action Repeat the recent configuration change for the specified interface and verify that the specified process is operating correctly. If this behaviour persists then check that there are enough resources available to run IP ARM or contact your technical support representative copying the error message exactly as it appears.
IP_ARM_PLIB Messages
Error Message%IP-IP_ARM_PLIB-3-EVENT_SET_RETRY_FAILED Event set retry failed, error : [chars]
Explanation A call to set the retry timeout for producers to bind with iparm failed. This will call default timeout values to be used.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IP_ARM_TEST Messages
Error Message%IP-IP_ARM_TEST-6-RCVD_UPDATE [chars]
Explanation Update received
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IP_ARM Messages
Error Message%IP-IP_ARM-3-CFLCT_CFG_ERR conflict policy apply error during [chars], error -- [chars]
Explanation Internal error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IP_ARM-3-CFLCT_CFG_PLCY_INVALID Invalid [chars] value of [hex]
Explanation Internal error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IP_ARM-3-CFLCT_DB_WALK_ERR Conflict database management walk failed [chars]
Explanation Internal error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IP_ARM-3-CFLCT_FORCED_DOWN The [chars] address [chars]/[dec] on [chars] conflicts with other [chars] addresses and has been forced down
Explanation The specified IP address conflicts with other IP addresses on the network portion of their IP addresses and has been forced down to prevent multiple operational conflicting IP addresses. This is an inconsistent configuration.
Recommended Action Reconfigure the IP addresses that share the common network portion specified.
Error Message%IP-IP_ARM-3-CFLCT_NOT_FOUND Conflict datastrcuture not found for ([chars])
Explanation An IP info structure with conflict flag set is not found in the conflict database.
Recommended Action This is an error condition indicating IP ARM database has erroneous information. Might have to restart IP ARM.
Error Message%IP-IP_ARM-3-INIT_FAILED Initialization failed, module: [chars], operation: [chars], error: [chars]
Explanation IP ARM's initialization has failed.
Recommended Action If this behaviour persists then check that there are enough resources available to run IP ARM or contact your technical support representative copying the error message exactly as it appears.
Error Message%IP-IP_ARM-3-LTRACE_ERR Failed to [chars]: [chars]
Explanation Internal error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IP_ARM-3-MHOST_DEFAULT_PIM An error occured with the default interface provided by PIM: [chars]
Explanation When multicast routing is turned on PIM will choose a default interface, based on whether the default has been configured and it's enabled state.
Recommended Action Change the mhost ipv4 default-interface configuration to some other physical or virtual interface.
Error Message%IP-IP_ARM-6-BAD_VISIBLE_COUNT Interface '[chars]' has more visible addresses than the stored visible count '[dec]'
Explanation Internal error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IP_ARM-6-CFGED_MHOST_DEFAULT_MGMT The configured mhost default interface([chars]) is a management interface, so, can't be used as the active
Explanation Management interfaces(on the RPs) are not allowed to be the mhost default interface as multicast routing is disabled on the management interface.
Recommended Action Change the mhost ipv4 default-interface configuration to some other physical or virtual interface.
Error Message%IP-IP_ARM-6-CFLCT_NO_LONGER The [chars] address [chars]/[dec] on [chars] is no longer forced down due to [chars] address conflicts
Explanation The IP address specified in the message previously conflicted with other configured IP addresses on some portion of the network portion of their IP addresses. The IP address no longer conflicts.
Recommended Action None. This is an informational message indicating a return to a correct consistent configuration.
Error Message%IP-IP_ARM-6-RTRID_GLOBAL_UNAVAILABLE The global router id has become unavailable
Explanation The global router id has become unavailable.
Recommended Action Ensure that a global router id has been configured and that the configured interface has a primary IPv4 address and is UP (a loopback interface is strongly recommended), or that the configured IPv4 address exists on an interface that is UP.
Error Message%IP-IP_ARM-6-UNNUM_CFLCT The [chars] unnumbered interface [chars] references the unnumbered interface [chars] and has therefore been forced down
Explanation The IP unnumbered specified in the message references another unnumbered interface. This is not consistent configuration.
Recommended Action Reconfigure one of the IP unnumbered interfaces so that the unnumbered interface does not reference another unnumbered interface.
Error Message%IP-IP_ARM-6-UNNUM_CFLCT_NO_LONGER The [chars] unnumbered interface [chars] no longer references another unnumbered interface
Explanation The IP unnumbered specified in the message references previously referenced another unnumbered interface. This is no longer the case.
Recommended Action None. This is an informational message indicating a return to a correct consistent configuration.
IPV4_EDM Messages
Error Message%IP-IPV4_EDM-3-BAGDECODE_FAILED Bag Decode failed ([chars])
Explanation Process could not decode the bag.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_EDM-3-BAGDECODE_FAILED Bag Decode failed ([chars])
Explanation Process could not decode the bag.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_EDM-3-DATALIST_ADD_FAILED Failed to add an external data manager datalist for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The attempt to add an item to an external data manager datalist has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_EDM-3-DATALIST_ADD_FAILED Failed to add an external data manager datalist for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The attempt to add an item to an external data manager datalist has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_EDM-3-DATALIST_CREATE_FAILED Failed to create external data manager datalist for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The creation of the external data manager list has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_EDM-3-DATALIST_CREATE_FAILED Failed to create external data manager datalist for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The creation of the external data manager list has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_EDM-3-DECODE_FAILED Failed to decode [chars] data
Explanation IPV4 could not decode data supplied by the indicated external data manager.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_EDM-3-DECODE_FAILED Failed to decode [chars] data
Explanation IPV4 could not decode data supplied by the indicated external data manager.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_EDM-3-ENCODE_FAILED Failed to encode [chars] data in external data manager
Explanation A process has requested information from ipv4_io through SysDB, probably as a result of executing a show command. The data requested could not be encoded.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_EDM-3-ENCODE_FAILED Failed to encode [chars] data in external data manager
Explanation A process has requested information from ipv4_io through SysDB, probably as a result of executing a show command. The data requested could not be encoded.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_EDM-3-GET_FAILED Failed to retrieve [chars] from the external data manager
Explanation IPV4 could not retrieve information required for completing the entered command from an external data manager.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_EDM-3-GET_FAILED Failed to retrieve [chars] from the external data manager
Explanation IPV4 could not retrieve information required for completing the entered command from an external data manager.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_EDM-3-NUM_NODE Failed to determine the number of nodes on the router
Explanation Could not determine the number of nodes on the router.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_EDM-3-NUM_NODE Failed to determine the number of nodes on the router
Explanation Could not determine the number of nodes on the router.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_EDM-3-OPEN_FAILED Failed to open external data manager in [chars]
Explanation While processing the indicated show command, the ipv4_io process could not connect to the SysDB server.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_EDM-3-OPEN_FAILED Failed to open external data manager in [chars]
Explanation While processing the indicated show command, the ipv4_io process could not connect to the SysDB server.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_EDM-3-REGISTER_FAILED IPV4_IO failed to register its external data manager - [chars]: [chars]
Explanation The ipv4_io process failed when attempting to register its external data manager with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_EDM-3-REGISTER_FAILED IPV4_IO failed to register its external data manager - [chars]: [chars]
Explanation The ipv4_io process failed when attempting to register its external data manager with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_EDM-3-SYSDB_BIND_FAILED Failed to connect to SysDB in [chars] ([chars])
Explanation Failed to connect to SysDB while starting the indicated subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_EDM-3-SYSDB_BIND_FAILED Failed to connect to SysDB in [chars] ([chars])
Explanation Failed to connect to SysDB while starting the indicated subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_EDM-3-SYSDB_GETITEM_FAILED Failed trying to get the SysDB item [chars] ([chars])
Explanation Failed to get an item in SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_EDM-3-SYSDB_GETITEM_FAILED Failed trying to get the SysDB item [chars] ([chars])
Explanation Failed to get an item in SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_EDM-6-BAGREG_FAILED IPV4_IO failed to register the [chars] external data manager data blocks
Explanation The ipv4_io process failed while attempting to register the indicated external data manager data blocks with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_EDM-6-BAGREG_FAILED IPV4_IO failed to register the [chars] external data manager data blocks
Explanation The ipv4_io process failed while attempting to register the indicated external data manager data blocks with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV4_IO Messages
Error Message%IP-IPV4_IO-2-ERR_PA_CLIENT_OPEN couldn't establish connection with PA, error = [chars]
Explanation ipv4 io couldn't establish connection with LPTS port Arbitrator.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-2-GSP_INIT_FAILED Cannot initialize Group Services ([chars])
Explanation IPv4 failed to initialize Group Services. may fail.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-2-GSP_NODEID_FAILURE failed to get gsp_nodeid from dest_nodeid, error [chars]
Explanation Failed to convert from nodeid_td to gsp_node_id type.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-2-GSP_NODESET_FAILURE GSP failed to add node [dec] to SNV with error [chars]
Explanation GSP failed to add node to SNV. IPv4 will not be able to send the relevant msg to particular node.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-2-GSP_SEND_NODESET_FAILURE GSP failed to send msg to set of nodes [chars]
Explanation IPv4 will not be able to send the relevant msg to particular node set
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-2-INIT_FAILED Cannot initialize [chars]: [chars] ([hex])
Explanation IPV4 local switching service initialization failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-2-MPA_REPLAY_FAILED MPA replay failed for ipv4_io. Restarting self
Explanation Couldn't update MPA with the mhost state, on MPA restart.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-2-NETIO_INIT_FAILED Cannot initialize Connection to NetIO
Explanation IPv4 failed to connect to Netio. may fail.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-2-OPTION_UPDATE_FAIL Cannot update option registry in ipv4_io [chars]
Explanation IPV4 failed to make an entry for option registry requested by application
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-2-PAK_HDR_COUNT_ZERO Got the total packet header count as zero
Explanation The total packet header count obtained from pakman is zero.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-2-STATS_INIT_FAILED IPv4 stats initialization failed ([chars])
Explanation Could not initialize the IP statistics structure.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-2-XIPC_INIT_FAILED couldn't initialize the XIPC queues, error = [chars]
Explanation ipv4 io couldn't create the XIPC queues needed to be able to send/recv packets from transports.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-ADD_GROUP_FAILED IP add multicast group membership failed for group [chars] on interface [chars]
Explanation IPv4 was unable to add membership to the group. Commonly, this is done for 224.0.0.1 by ipv4-io with no associated socket when an interface is enabled, or for all groups (multicast promiscuous mode) whem multicast routing is enabled.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-ADDR_INIT_FAILED IPV4_IO Address repository initialization failed ([chars])
Explanation The IPV4_IO process failed to initialize the address repository.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-CONFIG_INIT_FAILED IPV4_IO Configuration initialization failed
Explanation The IPV4_IO process failed to initialize its configuration.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-DB_INIT_FAILED IPV4_IO DB initialization failed ([chars])
Explanation The IPV4_IO process failed to initialize its internal DB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-DEBUG_INIT_FAILED IPV4_IO Debug initialization failed
Explanation The IPV4_IO process failed to initialize its debugging.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-DEBUG_REGISTRATION_FAILED IPV4_IO process failed to register its debugs ([chars])
Explanation The ipv4_io process failed to register its debug routines correctly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-EA_THREAD_INIT_FAILED Couldn't create the EA thread ([chars])
Explanation Could not initialize the EA thread.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-EDM_INIT_FAILED IPV4_IO EDM initialization failed ([chars])
Explanation The IPV4_IO process failed to initialize its edm manager.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-EOF [chars]
Explanation IPv4 reached end of event loop function.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-ERR_AVLBL_MTU [chars] [dec]: [hex]
Explanation Minimum IPv4 MTU must be 68 bytes. Available IPv4 mtu is not within the valid range.
Recommended Action Adjust the lower layer mtu such that atleast 68 bytes is available to IPv4.
Error Message%IP-IPV4_IO-3-ERR_CREATE_REGISTER Failed to register create notification for interface [chars] ([chars]: [chars])
Explanation IPv4 IO registers to be notified of Forwarder interface creation if its not already available when IPv4 IO starts. Above failure could mean that forwarder will not be available for IPv4 packets.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-ERR_FINT_NAME Failed to get interface name of local fint ([chars])
Explanation Forwarder Interface name is not available
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-ERR_ICMPLIB Failed to initalize ICMP library ([chars])
Explanation IPv4 IO failed to initialize ICMP library. This will result in failure sending ICMP error packets.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-ERR_LTRACE Failed to [chars]: [chars]
Explanation Internal error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-ERR_NULL_HANDLE_ALLOC Error: Port Arbtitrator allocated a NULL handle
Explanation Handle allocated by port arbitrator is invalid.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-ERR_PA_BIND Couldn't bind with Port Arbitrator for local interest, error = [chars]
Explanation A call made to pa_client_bind has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-ERR_PA_BIND_RETVAL Error in binding [chars] for local interest with Port Arbitrator
Explanation A certain ICMP type couldn't be registered with PA.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-ERROR_INIT_FAILED Failed to do error initialization ([chars])
Explanation IPv4 failed initialize timers used for error recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-EVENTCONN_CREATE_FAILED IPV4_IO Failed to create evm conn for [chars] ([chars])
Explanation The IPV4_IO process failed to do event connection create.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-EVENTMGR_CREATE_FAILED IPV4_IO Event Manager create failed
Explanation The IPV4_IO process failed to create the event manager.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-FILTER_REDIRECT_INIT_FAILED IPV4_IO HSRP filter redirect initialization failed
Explanation The IPV4_IO process failed to initialize HSRP filtering redirects.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-FORUS_INIT_FAILED IPV4_IO Forus server initialization failed
Explanation The IPV4_IO process failed to initialize the forus server.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-GROUP_CREATE_FAILED IPv4_IO failed to create a gsp group([chars]), retrying
Explanation group_create failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-HANDLER_REGISTER_FAILED IPV4_IO could not register its [chars] handler ([chars], [dec])
Explanation The IPV4_IO process could not register the indicated event handler.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-HSSD_REGISTER_FAILED IPV4_IO Packet hssd register failed ([chars])
Explanation The IPV4_IO process failed to register for the packet HSSD.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-IDB_AVAIL_FAILURE IPV4 IO IDB for an ifhandle [dec] is not available
Explanation IPV4 IO was either not able to find or create an idb or lookup in existing database. Intended action for this interface will not happen.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-INTF_CONFIG_FAIL Address Configuration failed for interface [chars]
Explanation IPv4 failed to configure IP address for this interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-INTF_NOT_FOUND Unable to find interface [chars]
Explanation IPV4 IO was not able to find particular interface in the system
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-INVALID_MEMBERSHIP_MOD Multicast group membership operation on invalid group [chars]
Explanation IPV4 received a transport request to modify a group membership that is not recorded in the IPV4 membership DB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-MCAST_MEMBERSHIP_FILTER_FAILED Modifiation of multicast group membership filter in FIB AND L2 driver failed for group [chars]
Explanation IPV4 failed to recover from an unsuccessful multicast group join or leave due to dual failure modifying the FIB and L2 driver filter.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-MCAST_ONOFF_FAILED Failed to reset FIB entries for transition to mcast forwarding [chars]
Explanation IPv4 was unable to modify the class D FIB entries for transition to or from multicast forwarding configuration. The attempt to change the class D FIB pointers may be repeated.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-MGII_INIT_FAILED IPV4_IO Mgii thread initialization failed
Explanation The IPV4_IO process failed to initialize the MGII thread.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-MGII_MUTEX mutex failed: [chars]: [chars]
Explanation Failure of thread operations on the mutex protecting the multicast group memberships.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-MGII_UPDATE_FAILED failed to update IGMP: [chars]: [chars]
Explanation ipv4-io failed to update the multicast group internal interest for the IGMP process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-MHOST_CONFIG_DEFAULT_FAILED Failed to configure the MHost default interface membership on the real interface : [chars]
Explanation When changing the MHost default interface from one real interface to another, IPV4 IO failed to remove all multicast group memberships from the old interface, and/or add them to the new interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-MHOST_DEFAULT_CONFIG Failed handling change in mhost default interface ([chars])
Explanation Failed handling change in mhost default interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-MPA_RECONNECT_FAILED MPA reconnect failed for ipv4_io. Restarting self
Explanation Couldn't reconnect to MPA.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-MTUS_INIT_FAILED IPV4_IO MTU server initialization failed
Explanation The IPV4_IO process failed to initialize its MTU server.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-PACKETMGR_CONNECT_FAILED IPV4_IO Packet Manager connection failed ([chars])
Explanation The IPV4_IO process failed to connect to the packet manager.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-PFI_INIT_FAILED Couldn't initialize the pfi ifh service ([chars])
Explanation A call to initialize the pfi ifh service failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-REMOVE_GROUP_FAILED IP remove multicast group membership failed for group [chars] on interface [chars]
Explanation IPv4 was unable to remove membership to the group. Commonly, this is done for 224.0.0.1 by ipv4-io with no associated socket when an interface is disabled, or for all groups (multicast promiscuous mode) whem multicast routing is disabled.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-SETUP_HANDLERS_FAILED IPV4_IO Setting up Event handlers failed
Explanation The IPV4_IO process failed to setup its event handlers.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-SVC_REGISTER_FAILED Registering icmp stats with RPC failed
Explanation Registering icmp stats with RPC failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-SYSDB_BIND_FAILED Failed to connect to SysDB in [chars] ([chars])
Explanation Failed to connect to SysDB while starting the indicated subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-SYSDB_CONNECT_FAILED Default connection to SysDB failed ([chars], [chars])
Explanation Could not connect to SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-SYSDB_CREATEITEM_FAILED Failed trying to create the SysDB item [chars] ([chars])
Explanation Failed to create an item in SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-TIMER_INIT_FAILED IPV4_IO Timer initialization failed
Explanation The IPV4_IO process failed to initialize its timers.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-TRANSP_CLOSE_FAILED Failed to handle transport closing the connection ([chars])
Explanation IPv4 failed to handle transport closing the connection.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-TRANSPORT_FSV_REGISTER_FAILED IPV4_IO Transport FSV register failed
Explanation The IPV4_IO process failed to register for the transports' FSV.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-TRANSPORT_GET_PID_FAILED [chars] failed to get destination pid
Explanation IPV4_IO failed while attempting to initialize the transport subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-3-UNKNOWN_MESSAGE Unknown [chars] received by ipv4_io ([dec])
Explanation The IPV4_IO process has received an unknown event message.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-6-CLIENT_TIMEOUT Timeout waiting for local switching application to [chars]
Explanation A request to remove or update a local switching operation has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-6-ERR_ADD_ENCAP Failed to add encapsulation on [chars] ([chars])
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-6-ERR_CREATE_CHAIN Failed to create chain for [chars] ([dec])
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-6-ERR_DUP_ADDR Incorrect IP address assignment: [chars] overlaps with [chars].
Explanation The address configured on this interface overlaps with an assigned address on an interface which is not in shutdown state.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-6-ERR_GET_CAPS Unable to obtain caps identifier for [chars] ([dec])
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-6-ERR_GET_PROTO Unable to obtain protocol identifier for [chars] ([dec])
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-6-ERR_IM Failure ([chars]) : [chars]
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-6-ERR_IOCIFUP Failed to initialize [chars] ([dec])
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-6-ERR_MTU Unable to obtain MTU information for [chars] ([dec])
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-6-ERR_REMOVE_ENCAP Failed to remove encapsulation on [chars] ([chars])
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-6-ERR_ROUTE_ADD Couldn't add [chars] route to [chars]/[dec] ([dec])
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-6-ERR_STATE Unable to obtain STATE information for [chars] ([dec])
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-6-ERR_SYSDB_EV Unexpected configuration event
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-6-NO_IFTYPE Unable to determine interface type for [chars] ([dec])
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_IO-6-SWITCH_FAILED Request to [chars] switching request ([chars] [chars] [dec] [dec] [dec]) failed: [chars] ([hex])
Explanation A request to install or remove a switching request for the flow identified by (src_addr dst_addr protocol src_port dst_port) failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV4_MA Messages
Error Message%IP-IPV4_MA-2-INIT_FAILED Cannot initialize [chars]: [chars] ([hex])
Explanation Initialization of the IPv4 MA process failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_MA-3-ADD_GROUP_FAILED IP add multicast group membership failed for group [chars] on interface
Explanation IPv4 was unable to add membership to the group. Commonly, this is done for 224.0.0.1 by ipv4-ma with no associated socket when an interface is enabled, or for all groups (multicast promiscuous mode) whem multicast routing is enabled.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_MA-3-ADDR_INIT_FAILED IPV4_MA Address repository initialization failed ([chars])
Explanation The IPV4_MA process failed to initialize the address repository.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_MA-3-CONFIG_INIT_FAILED IPV4_MA Configuration initialization failed
Explanation The IPV4_MA process failed to initialize its configuration.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_MA-3-DB_INIT_FAILED IPV4_MA DB initialization failed ([chars])
Explanation The IPV4_MA process failed to initialize its internal DB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_MA-3-DEBUG_INIT_FAILED IPV4_MA Debug initialization failed
Explanation The IPV4_MA process failed to initialize its debugging.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_MA-3-DEBUG_REGISTRATION_FAILED IPV4_MA process failed to register its debugs ([chars])
Explanation The IPV4_MA process failed to register its debug routines correctly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_MA-3-EDM_INIT_FAILED IPV4_MA EDM initialization failed ([chars])
Explanation The IPV4_MA process failed to initialize its edm manager.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_MA-3-EOF [chars]
Explanation IPv4 reached end of event loop function.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_MA-3-ERR_AVLBL_MTU [chars] [dec]: [hex]
Explanation Minimum IPv4 MTU must be 68 bytes. Available IPv4 mtu is not within the valid range.
Recommended Action Adjust the lower layer mtu such that atleast 68 bytes is available to IPv4.
Error Message%IP-IPV4_MA-3-ERR_CREATE_REGISTER Failed to register create notification for interface [chars] ([chars]: [chars])
Explanation IPv4 MA registers to be notified of Forwarder interface creation if its not already available when IPv4 MA starts. Above failure could mean that forwarder will not be available for IPv4 packets.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_MA-3-ERR_FINT_NAME Failed to get interface name of local fint ([chars])
Explanation Forwarder Interface name is not available
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_MA-3-ERR_LTRACE Failed to [chars]: [chars]
Explanation Internal error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_MA-3-ERROR_INIT_FAILED Failed to do error initialization ([chars])
Explanation IPv4 failed initialize timers used for error recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_MA-3-EVENTCONN_CREATE_FAILED IPV4_MA Failed to create evm conn for [chars] ([chars])
Explanation The IPV4_MA process failed to do event connection create.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_MA-3-EVENTMGR_CREATE_FAILED IPV4_MA Event Manager create failed
Explanation The IPV4_MA process failed to create the event manager.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_MA-3-HANDLER_REGISTER_FAILED IPV4_MA could not register its [chars] handler ([chars], [dec])
Explanation The IPV4_MA process could not register the indicated event handler.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_MA-3-IDB_AVAIL_FAILURE IPV4 MA IDB for an ifhandle [dec] is not available
Explanation IPV4 MA was either not able to find or create an idb or lookup in existing database. Intended action for this interface will not happen.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_MA-3-INVALID_MEMBERSHIP_MOD Multicast group membership operation on invalid group [chars]
Explanation IPV4 received a transport request to modify a group membership that is not recorded in the IPV4 membership DB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_MA-3-REMOVE_GROUP_FAILED IP remove multicast group membership failed for group [chars] on interface
Explanation IPv4 was unable to remove membership to the group. Commonly, this is done for 224.0.0.1 by ipv4-ma with no associated socket when an interface is disabled, or for all groups (multicast promiscuous mode) whem multicast routing is disabled.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_MA-3-REPLICATE_DPC_INVALID_COOKIE Got invalid cookie for replicating interface , cookie - [hex], batch cookie [hex]
Explanation IPv4 MA got an unexpected cookie for the specified interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_MA-3-SETUP_HANDLERS_FAILED IPV4_MA Setting up Event handlers failed
Explanation The IPV4_MA process failed to setup its event handlers.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_MA-3-SYSDB_BIND_FAILED Failed to connect to SysDB in [chars] ([chars])
Explanation Failed to connect to SysDB while starting the indicated subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_MA-3-TIMER_INIT_FAILED IPV4_MA Timer initialization failed
Explanation The IPV4_MA process failed to initialize its timers.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_MA-3-UNKNOWN_MESSAGE Unknown [chars] received by ipv4_ma ([dec])
Explanation The IPV4_MA process has received an unknown event message.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_MA-6-ERR_ADD_ENCAP Failed to add encapsulation on ([chars])
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_MA-6-ERR_IM Failure ([chars]) : [chars]
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_MA-6-ERR_MTU Unable to obtain MTU information for ([dec])
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV4_MA-6-ERR_REMOVE_ENCAP Failed to remove encapsulation on ([chars])
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV6_EA Messages
Error Message%IP-IPV6_EA-3-ERROR gsr ipv6_ea: failed at [chars], because of [chars]
Explanation Initialization process such as getting an evm failed.
Recommended Action sysmgr will retry to start the gsr lc ipv6_ea. If not recovered, it's a fatal condition. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. *REDUCE*
Error Message%IP-IPV6_EA-3-INFO gsr ipv6_ea: [chars]
Explanation This is an informational msg.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_EA-3-INIT Failed to initialize [chars], because of [chars]
Explanation Initialization process such as getting an evm failed.
Recommended Action sysmgr will retry to start the hfrlc_ipv6_ea. If not recovered, it's a fatal condition. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. *REDUCE*
IPV6_MA Messages
Error Message%IP-IPV6_MA-3-ADD_GROUP_FAILED IP add multicast group membership failed for group [chars] on [chars]
Explanation Unable to add membership to the group.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_MA-3-ERR_ADD_ENCAP Failed to add [chars] encapsulation to [chars] ([chars])
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_MA-3-ERR_ADDRSVR_INIT Failed to initialize as Address Svr. Error -- [chars]
Explanation Failed to initialize as local IP Address Server
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_MA-3-ERR_DPC_SEND [chars] [chars] [dec]([chars])
Explanation Failed to send DPC to EA. This can result in v6 parameters not reaching the hardware.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_MA-3-ERR_INIT Failed to initialize [chars], Error -- [chars]([dec])
Explanation Failed to initialize as producer of the Local Address Service Database
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_MA-3-ERR_LAS_P_INIT Failed to initialize as LAS producer. Error -- [chars]
Explanation Failed to initialize as producer of the Local Address Service Database
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_MA-3-ERR_LL_CFG [chars]: ([chars])
Explanation This might result in failure generating linklocal address on certain LC.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_MA-3-ERR_LTRACE_INIT_FAIL [chars] [chars] [chars]
Explanation There was a failure during an ltrace_init api call which resulted in the failure as indicated in the message text.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_MA-3-ERR_MTU [chars] [dec]: [chars]
Explanation Minimum IPv6 MTU must be 1280. Available ipv6 mtu is not within the valid range.
Recommended Action Adjust the lower layer mtu such that atleast 1280 bytes is available to ipv6.
Error Message%IP-IPV6_MA-3-ERR_REMOVE_ENCAP Failed to remove [chars] encapsulation from [chars] ([chars])
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_MA-3-ERR_RIB_UPDATE_COMPLETE ([chars])
Explanation Failed in signalling update complete to RIB. This might cause delay in RIB convergence.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_MA-3-ERR_TIMER_ADDL_CTXT [chars] ([chars])
Explanation The IPV6 MA process failed to add context to timer.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_MA-3-ERR_TIMER_INIT IPV6 MA Timer initialization failed - [chars]
Explanation The IPV6 MA process failed to initialize its timers.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_MA-3-EVENT_CONN_ERR IPV6 MA Event Conn Error - [chars] ([chars])
Explanation The IPV6 MA process failed to initialize its event conn mgr infra.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_MA-3-EVENTMGR_CREATE_FAILED IPV6_MA Event Manager create failed
Explanation The IPV6_MA process failed to create the event manager.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_MA-3-REMOVE_GROUP_FAILED IP remove multicast group membership failed for group [chars] on [chars]
Explanation Unable to add membership to the group.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_MA-3-SYSDB_BIND_FAILED Failed to connect to SysDB in [chars] ([chars])
Explanation Failed to connect to SysDB while starting the indicated subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_MA-6-ERR_IM IM API Failure ([chars]) : [chars]
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_MA-6-ERR_PFI PFI API Failure ([chars]) : [chars]
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_MA-6-ERR_STATS [chars]: [chars]
Explanation This might result in failure in collecting IPV6 stats on this interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_MA-6-ERR_STATS_INTF [chars]: [hex] [chars]
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV6_ND Messages
Error Message%IP-IPV6_ND-3-ADDRESS_DUPLICATE Duplicate address [chars] has been detected
Explanation Address duplication has been detected.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_ND-3-ERR_ADD_NEIGHBOUR Failed to add neighbor.
Explanation IPv6 Neighbor Discovery process was unable to insert an adjacency into it's local table.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_ND-3-ERR_AIB_ADD_ADJ Unable to add adjacency into AIB.
Explanation A problem occurred while attempting to add an adjacency into the AIB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_ND-3-ERR_AIB_CONN_CREATE Unable to create connection handle to AIB [chars] ([dec])
Explanation A problem occurred while creating a connection identifier to communicate with the AIB process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_ND-3-ERR_AIB_CONN_OPEN Unable to open connection to AIB [chars] ([dec])
Explanation A problem occurred while opening a connection to communicate with the AIB process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_ND-3-ERR_AIB_DEL_ADJ Unable to delete adjacency from AIB.
Explanation A problem occurred while attempting to delete an adjacency from the AIB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_ND-3-ERR_BAG_ENCODE Failed to encode bag : [chars] ([dec])
Explanation The attempt to encode statistics into a bag has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_ND-3-ERR_BAG_REGISTER_ALL Failed to register all the bags : [chars] ([dec])
Explanation The attempt to register all the bags has failed
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_ND-3-ERR_BCDL [chars] : Error = [chars] ([dec])
Explanation An error as indicated in the debug message has been discovered in the IPv6 ND code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_ND-3-ERR_DATA_HANDLER_ATTACH Unable to attach to [chars] : Error = [chars] ([dec])
Explanation A problem occurred while attempting to attach to data handler identified by the debug string.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_ND-3-ERR_EDM_CONN_CREATE Unable to create connection handle to EDM [chars] ([dec])
Explanation A problem occurred while creating a connection identifier to communicate with the EDM process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_ND-3-ERR_EDM_CONN_OPEN Unable to open connection to EDM [chars] ([dec])
Explanation A problem occurred while opening a connection to communicate with the EDM process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_ND-3-ERR_EDM_REGISTER Failed to register edm : [chars] ([dec])
Explanation The attempt to register the edm has failed
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_ND-3-ERR_EVENT_HANDLER_ATTACH Unable to attach to [chars] : Error = ([dec])
Explanation A problem occurred while attempting to attach with the process identified by the debug string.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_ND-3-ERR_EVENT_MGR_CREATE [chars] unable to create the event manager.
Explanation IPv6 ND has failed to create the event manager. It will exit upon this condition.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_ND-3-ERR_EXTERNAL_FAIL [chars] [chars] (errno=[dec])
Explanation There was a failure during an external api call which resulted in the failure as indicated in the message text.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_ND-3-ERR_GET_PAK Unable to find [chars] in packet.
Explanation A problem occurred while attempting to resolve information from a packet.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_ND-3-ERR_IFH_CONN_CREATE Unable to create connection handle to IFH [chars] ([dec])
Explanation A problem occurred while creating a connection identifier to communicate with the IFH server.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_ND-3-ERR_IFH_CONN_OPEN Unable to open connection to IFH [chars] ([dec])
Explanation A problem occurred while opening a connection to communicate with the IFH server.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_ND-3-ERR_IM_BIND Failed to bind to IM ([chars]): [chars] ([dec])
Explanation The attempt to communicate with IM failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_ND-3-ERR_IM_MEDIA_NOT_SUPPORTED [chars] [chars]
Explanation IPv6 Neighbor Discovery does not opeate on this interface type.
Recommended Action Debug message only. No action is required.
Error Message%IP-IPV6_ND-3-ERR_IM_PROTO_LOOKUP Unable to obtain protocol identifier for [chars] ([dec])
Explanation A problem occurred while looking up the protocol/capsulation number for IPv6.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_ND-3-ERR_INTERNAL_FAIL [chars] [chars] (errno=[dec])
Explanation There was a failure during the execution of an internal operation which resulted in the failure as indicated in the message text.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_ND-3-ERR_PAK_GET_OFFSET Couldn't retrieve [chars] offset for packet. [chars] ([dec])
Explanation An attempt to get the offset of the packet into the layer indicated has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_ND-3-ERR_PAK_V6_HDR_READ Couldn't read IPv6 header from packet: read len = [dec].
Explanation An attempt to read the IPv6 header in the packet has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_ND-3-ERR_PAKMGR_CONNECT_FAILED Packet Manager connect attempt has failed. Error = [dec]
Explanation An attempt to connect to the Packet Manager has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_ND-3-ERR_PUNTBACK couldn't punt packet for ND processing, err: [chars] ([dec])
Explanation The IPv6 ND component was unable to punt the packet back to the originating partner process. The Packet was dropped.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_ND-3-ERR_SYSDB_BIND Failed to bind to sysdb : [chars] ([dec])
Explanation The attempt to communicate with sysdb failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_ND-6-INFO_BCDL [chars]
Explanation --
Recommended Action No action is required.
IPV6_SW Messages
Error Message%IP-IPV6_SW-3-CLEAR_MAPPING_FAILED clear mapping ipv6 ([dec]) from media [chars] failed: [chars]
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_SW-3-ERR_ATTACH_FSV couldn't attach FSV, err: [chars]
Explanation The IPv6 NetIO component was unable to attach the required FSV before passing the packet to the IPv6 partner process. The Packet was dropped.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_SW-3-ERR_DELIVER_FAIL couldn't deliver packet for [chars], err: [chars]
Explanation The IPv6 NetIO component was unable to deliver the packet to the IPv6 Partner Process. The Packet was dropped.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_SW-3-ERR_MEDIA_REGISTER [chars] : Failed for ipv6 proto to [chars] ([chars])
Explanation netio media register or callback error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_SW-3-ERR_NETIO_MUTEX_LOCK Cannot lock packet mutex in function [chars], err: [chars]
Explanation The IPv6 NetIO component was unable to lock packet mutex while doing a control action. The control action failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_SW-3-ERR_NO_INTERFACE IPv6 received a packet bound to a nonexistent interface, err: [chars]
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_SW-3-ERR_PAK_REDIRECT couldn't duplicate packet (no redirect generated), err: [chars]
Explanation A packet has been sent to us when the sender should have been able to directly reach the destination. We were therefore also trying to generate an ICMP redirect message, but were unable to do so. The original packet would have been forwarded normally.
Recommended Action This generally indicates a low memory condition. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%IP-IPV6_SW-3-ERR_PUNT_ND couldn't punt packet for ND processing, err: [chars]
Explanation The IPv6 NetIO component was unable to punt the packet to the IPv6 ND Partner Process in order for Neighbour Resolution to occur. The Packet was dropped.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_SW-3-ERR_PUNT_SWITCH couldn't punt packet for SWITCH processing, err: [chars]
Explanation The IPv6 NetIO component was unable to punt the packet to the IPv6 Partner Process in order for it to be Switched. The Packet was dropped.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_SW-3-ERR_READ_PUNT_REASON_FAILED couldn't read punt reason, err: [chars]
Explanation The IPv6 NetIO component was unable to read the Packet Punt Reason supplied by the Hardware forwarding component. The Packet was dropped.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_SW-3-NEED_SLOW_ROUTINE IPv6 can't access pak [pointer] header in [chars] - need slow routine
Explanation The IPv6 base header in the packet could not be directly accessed in the named routine, and hence the packet was dropped. This is due to the packet not being within the first particle or the header not being completly contained within one particle. If the slow switching routines (using pak_netio_ API calls) had been compiled in then the packet could have been switched.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_SW-3-SET_MAPPING_FAILED set mapping ipv6 ([dec]) to media [chars] failed: [chars]
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6_SW-4-ERR_DEBUG_INIT A error occurred during debug initialization, err: [chars]
Explanation The IPv6 NetIO component encountered an error during debug initialisation
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV6 Messages
Error Message%IP-IPV6-2-SIGNAL signal: [chars]
Explanation IPv6 IO encountered an error while registering a signal
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6-3-DEBUG_INIT_FAILED IPv6 IO Debug Initialisation Failed
Explanation IPv6 IO failed to initialise debugging
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6-3-EDM_DECODE_FAILED Failed to decode [chars] data
Explanation IPV6 could not decode data supplied by the indicated external data manager.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6-3-EDM_ENCODE_FAILED Failed to encode [chars] data in external data manager
Explanation A process has requested information from ipv6_io through SysDB, probably as a result of executing a show command. The data requested could not be encoded.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6-3-EDM_OPEN_FAILED Failed to open external data manager in [chars]
Explanation While processing the indicated show command, the ipv6_io process could not connect to the SysDB server.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6-3-EDM_REGISTER_FAILED IPV6_IO failed to register its external data manager - [chars]
Explanation The ipv6_io process failed when attempting to register its external data manager with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6-3-ERR_ADD_ENCAP Failed to add [chars] encapsulation to [chars] ([chars])
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6-3-ERR_LTRACE_INIT_FAIL [chars] [chars] [chars]
Explanation There was a failure during an ltrace_init api call which resulted in the failure as indicated in the message text.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6-3-ERR_NULL_HANDLE_ALLOC Error: Port Arbtitrator allocated a NULL handle
Explanation Handle allocated by port arbitrator is invalid.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6-3-ERR_PA_BIND Couldn't bind with Port Arbitrator for local interest, error = [chars]
Explanation A call made to pa_client_bind has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6-3-ERR_PA_BIND_RETVAL Error in binding [chars] for local interest with Port Arbitrator
Explanation A certain ICMP6 type couldn't be registered with PA.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6-3-ERR_REMOVE_ENCAP Failed to remove [chars] encapsulation from [chars] ([chars])
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6-3-EVENTCONN_CREATE_FAILED IPv6 IO failed to create evm conn for [chars]: ([dec]) [chars]
Explanation The IPv6 IO process failed to create a connection to a server
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6-3-INIT_FAILED [chars] ([chars])
Explanation IPv6 IO failed to initialise some services.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6-3-INVALID_INPUT Invalid IPv6 packet on input: [chars] (got [dec], should be [dec]), s: [chars] d: [chars]
Explanation IPV6 received an invalid format IP packet.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6-3-PACKET_ERROR_DISCARD [chars], (source: [chars], destination: [chars])
Explanation IPV6_IO discarded a packet due to the indicated error.
Recommended Action Based on the error indicated, investigate the source of the and links for packet corruption or other errors.
Error Message%IP-IPV6-3-PACKETMGR_CONNECT_FAILED IPv6 IO Packet Manager connection Failed: ([dec]) [chars]
Explanation The IPv6 IO process failed to connect to the packet manager
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6-3-PAK_FSV_WRITE_FAILED Could not write packet specific feature vectors in [chars] ([chars], [unsigned int])
Explanation IPv6_IO could not write the packet specific features.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6-3-PAK_SEND_TO_TRANSPORT_FAILED IPv6_IO could not transfer packet to the transport layer ([unsigned int], [chars])
Explanation IPv6_IO attempted to write a packet to the transport layer and failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6-3-STATS_SHM_INIT_FAILED Failed to initialize shm for ipv6 traffic stats
Explanation While trying to create a shared memory object for ipv6 traffic statistics, encountered an error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6-3-SYSDB_BIND_FAILED Failed to connect to SysDB in [chars] ([chars])
Explanation Failed to connect to SysDB while starting the indicated subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6-3-SYSDB_CONNECT_FAILED Default connection to SysDB failed ([chars], [chars])
Explanation Could not connect to SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6-3-SYSDB_CREATEITEM_FAILED Failed trying to create the SysDB item [chars] ([chars])
Explanation Failed to create an item in SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6-6-EDM_BAGREG_FAILED IPV6_IO failed to register the [chars] external data manager data blocks
Explanation The ipv6_io process failed while attempting to register the indicated external data manager data blocks with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6-6-ERR_IM IM API Failure ([chars]) : [chars]
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-IPV6-6-ERR_PFI PFI API Failure ([chars]) : [chars]
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
LIBIPV4 Messages
Error Message%IP-LIBIPV4-3-ERR_CONV_ITEM Convergence item failure ([chars]) reason-([chars])
Explanation An error occurred processing a BGP convergence item operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-LIBIPV4-3-ERR_UNKNOWN_EVENT Received an unknown sysdb event ([hex]) for [chars]
Explanation The application has received an unknown sysdb notification event.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-LIBIPV4-7-ERR_DATALIST Helper address datalist operation failed, [chars], [chars]
Explanation The sysdb process fails to find the address of a specified active interface or of all active interfaces.
Recommended Action Debug message only. No action is required.
Error Message%IP-LIBIPV4-7-ERR_HSSD_REG Failed to register with pakman for hssd use.
Explanation The call to bind to pak_client_hssd_register failed.
Recommended Action Debug message only. No action is required.
Error Message%IP-LIBIPV4-7-ERR_INIT [chars]
Explanation Failure in intializing services required for the library to work
Recommended Action Debug message only. No action is required.
LIBIPV4PROTO Messages
Error Message%IP-LIBIPV4PROTO-3-ERR_GET_MTU Failed to get the MTU, [chars]
Explanation The transport fails to get the MTU from the network protocol process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-LIBIPV4PROTO-3-ERR_NETWORK_GONE Network protocol process is not up
Explanation The transport detects that the network protocol process is not running.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-LIBIPV4PROTO-3-ERR_NO_MEM Failed to allocate [dec] bytes of memory, [chars]
Explanation One of the memory allocation routines such as malloc() fails.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-LIBIPV4PROTO-3-PLIB_INIT [chars]: [chars]
Explanation There was a problem during the initialization of the ipv4 protocol library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-LIBIPV4PROTO-3-SETUP_NETIO_CONN [chars]: [chars]
Explanation There was a problem while setting up a connection to the netio process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-LIBIPV4PROTO-3-SETUP_RIB_CONN [chars]: [chars]
Explanation There was a problem while setting up a connection to the rib process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-LIBIPV4PROTO-3-SETUP_SYSDB_CONN [chars]: [chars]
Explanation There was a problem while setting up a connection to the sysdb process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-LIBIPV4PROTO-6-PAKHDR Failed to read IP header in packet (hl = [dec], read = [dec])
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-LIBIPV4PROTO-6-PAKHDR_ERROR Failed to read IP header - [chars]: [chars]
Explanation There was a problem with reading the IP header in the packet, so, can't process it.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-LIBIPV4PROTO-7-ERR_SEND_PACKET Failed to send a packet to the network layer, [chars]
Explanation The transport fails to send a message with packet to the network layer.
Recommended Action Debug message only. No action is required.
LIBIPV6PROTO Messages
Error Message%IP-LIBIPV6PROTO-3-ERR_CONNECT_RIB Failed to connect to the rib process
Explanation The transport fails to connect to the rib process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-LIBIPV6PROTO-3-ERR_FSV_REG FSV registration failed for [chars], error -- [chars]
Explanation FSV registration with packet manager failed
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-LIBIPV6PROTO-3-ERR_FSV_WRITE FSV resource busy, [chars]
Explanation The socket FSV resources are busy and cannot write.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-LIBIPV6PROTO-3-ERR_GET_MTU Failed to get the MTU, [chars]
Explanation The transport fails to get the MTU from the network protocol process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-LIBIPV6PROTO-3-ERR_LAS_GET_ADDR ipv6 LAS get address failed, error -- [chars]
Explanation The LAS get address routine returned an error. Most likely GSP/Fabric issue
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-LIBIPV6PROTO-3-ERR_LAS_INIT ipv6 LAS consumer initialization failed, error -- [chars]
Explanation The LAS initialization routine returned an error. Most likely GSP/Fabric issue
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-LIBIPV6PROTO-3-ERR_NETWORK_GONE Network protocol process is not up
Explanation The transport detects that the network protocol process is not running.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-LIBIPV6PROTO-3-ERR_NO_MEM Failed to allocate [dec] bytes of memory, [chars]
Explanation One of the memory allocation routines such as malloc() fails.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-LIBIPV6PROTO-3-IPSEC_HANDLE [chars]: [chars]
Explanation An error is encountered in handling a IP Security packet
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-LIBIPV6PROTO-7-ERR_SEND_PACKET Failed to send a packet to the network layer, [chars]
Explanation The transport fails to send a message with packet to the network layer.
Recommended Action Debug message only. No action is required.
MPA_CONSUMER Messages
Error Message%IP-MPA_CONSUMER-3-GEN_ERR [chars] failed [chars]: [chars]
Explanation *SUPPORT*
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-MPA_CONSUMER-3-GROUP_CREATE Group Create failed: [chars]
Explanation Group creation failed in MPA consumer API.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-MPA_CONSUMER-3-MALLOC_FAIL Fail to allocate memory
Explanation An internal error occured
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-MPA_CONSUMER-3-SYSMGR Failed to get Job ID from System Manager failed: [chars]
Explanation The specified system manager request failed. *SUPPORT*
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MPA Messages
Error Message%IP-MPA-2-DELETE_FAIL Unable to delete client node from AVL tree
Explanation An AVL tree internal erorr occurred while deleting a client node.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-MPA-2-DOWNLOAD_FAIL Unable to download multicast joins to a restarted csmr on node [chars] : [chars]
Explanation The Multicast Port Arbitrator was unable to download one or more multicast joins to a restarting instance of the consumer.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-MPA-2-INIT_FAILED Cannot initialize [chars]: [chars] ([hex])
Explanation Initialization failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-MPA-2-RTINSERT_FAIL Failed to insert an entry in MPA multicast database radix tree
Explanation A radix tree internal error occured while inserting in MPA multicast database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-MPA-3-ENCODE_FAILED Failed to encode data in external data manager
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The data requested could not be encoded.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-MPA-3-GENERR [chars]
Explanation General error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-MPA-3-GROUP_CREATE Group Create failed: [chars]
Explanation Multicast Port Arbitrator failed to create group.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-MPA-3-GROUP_REINIT Group reinit failed: [chars]
Explanation Multicast Port Arbitrator failed to reinitialize the group.
Recommended Action *SUPPORT
Error Message%IP-MPA-3-GROUP_SEND_NODE [chars]: failed to send group message to node [hex]: [chars]
Explanation An internal error was detected when trying to send a GSP message to the given node.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-MPA-3-GROUP_SETNOTIFY Group Setnotify failed group ([chars]): [chars]
Explanation Multicast Port Arbitrator failed to set notificatoin thru gsp.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-MPA-3-IFMGR Connection with Interface Manager failed: [chars]
Explanation The specified interface manager request failed. *SUPPORT*
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-MPA-3-INIT Initialization failed [[chars]], process terminated
Explanation An error occurred during initialization, causing the process to terminate.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-MPA-3-MALLOC_FAIL Fail to allocate memory
Explanation An internal error occured
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-MPA-3-MGII_MUTEX mutex failed: [chars]: [chars]
Explanation Failure of thread operations on the mutex protecting the multicast group memberships.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-MPA-3-NULLARG The MPA received multicast binding with NULL arguments
Explanation The Multicast Port Arbitrator received a message with NULL argument
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-MPA-3-OPEN_FAILED Failed to open external data manager is [chars]
Explanation While processing the indicated show command, the multicast port-arbitrator process could not connect to the SysDB server.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-MPA-3-RADIX_FAIL Radix operation [chars] failed for node [hex]
Explanation An internal error occured
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-MPA-3-REGISTER_FAILED Multicast Port Arbitrator failed to register its external data manager
Explanation The multicast port-arbitrator process failed when attempting to register its external data manager with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-MPA-3-SYSDB_BIND Failed to bind to sysdb ([chars]) : [chars]
Explanation The Multicast Port Arbitrator process could not bind to the SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-MPA-3-SYSDB_NOTIFICATION Failed to register for notification (path: [chars]) with error [chars]
Explanation The Multicast Port Arbitrator process could not register for notification with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-MPA-3-SYSDB_SET Failed to set tuple ([chars]) in sysdb : [chars]
Explanation The Multicast Port Arbitrator process could not bind to the SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-MPA-3-SYSMGR Failed to get Job ID from System Manager failed: [chars]
Explanation The specified system manager request failed. *SUPPORT
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-MPA-6-BAGREG_FAILED Multicast Port Arbitrator failed to register the [chars] external data manager data blocks
Explanation The multicast port-arbitrator process failed while attempting to register the indicated external data manager data blocks with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
PFILTER_MA Messages
Error Message%IP-PFILTER_MA-3-CONFIG Failed to [chars] acl [chars], in direction [chars] because [chars]
Explanation Config failure such as deleting ACL which is not configured
Recommended Action Check the configuration and apply the corrected one back If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. *REDUCE*
Error Message%IP-PFILTER_MA-3-INIT Failed to initialize [chars], because of [chars]
Explanation Initialization process such as getting an evm failed.
Recommended Action sysmgr will retry to start the pfilter_ma. If not recovered, it's a fatal condition. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. *REDUCE*
PLATFORM_IPV4 Messages
Error Message%IP-PLATFORM_IPV4-1-DLERR [chars] : [chars]
Explanation Error finding well-known function in dll.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
RAW Messages
Error Message%IP-RAW-3-ADD_PP Failed to insert the [chars] PCB proto into the PP list
Explanation The RAW transport failed to add the pcb protocol to a global list.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-DEBUG_INIT_EVENT Failed to initialize debug event: [chars]
Explanation The raw failed to initialize debug event.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-DEBUG_REGISTER Failed to register with debug library: [chars]
Explanation The raw process failed to register with the debug library to have the library automatically handle changes to any of the RAW debug flags.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-END_PROC Unexpected process termination, [chars]
Explanation The raw process terminated unexpectedly. This may be caused by: 1. failure to start a thread pool 2. a SIGTERM, SIGINT or SIGHUP signal is received
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-EVENT_ATTACH Failed to attach a handler for [chars]: [chars]
Explanation The raw process failed to attach a handler function to handle a specific event.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-EVM_CREATE Failed to create event manager: [chars]
Explanation The raw process failed to create an event manager channel.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-FSV_REGISTER Failed to register with packet manager to use the FSV
Explanation The raw process failed to register with packet manager for the FSV which is used between the IP [v4/6] I/O and its transport.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-GET_DB_VECTOR Failed to get the [chars] database vector
Explanation The RAW transport failed to get the network database vector.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-GET_NONPCB_VECTOR Failed to get [chars] non-PCB family vector: [chars]
Explanation The RAW transport failed to get the non-PCB network function vector.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-GET_PCB_VECTOR Failed to get [chars] PCB family vector: [chars]
Explanation The RAW transport failed to get the PCB network function vector.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-HSSD_REGISTER Failed to register HSSD with packet manager. Error [chars] returned
Explanation The ip pcb failed to register with packet manager for the vrfid HSSD which is used by FIB for table lookup.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-IM_LOOKUP Failed to lookup [chars] [chars] from IM: [chars]
Explanation The RAW transport failed to lookup a network attribute from the Inteface Manager.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-INIT_RETRY [chars] ([dec])
Explanation An error is encountered when the RAW process attempts to retry one of its initialization tasks with a network layer.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-LIST_CREATE Failed to create a raw protocol list
Explanation The raw process failed to create a list to hold raw protocol queues.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-LOAD_DLL Failed to load the library dll for [chars] [chars]
Explanation The raw process failed to load a library dll.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-LPTS_TRANSP_INIT Failed to initialize and establish a channel wit LPTS port arbitrator
Explanation The raw_ip process failed to create a communication channed with the LPTS port arbitrator.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-MUTEX_LOCK [chars]: [chars]
Explanation The RAW transport failed to lock a particular mutex.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-NO_MEM [chars] ([chars]): [chars]
Explanation The RAW transport failed to allocate memory for some data structure.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-NODE_STATE Failed to get the current state of this node: [chars]
Explanation The raw process failed to obtain the current state of this node to determine whether it's active or not.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-PAK_CONNECT Failed to connect to packet manager: [chars]
Explanation The raw process failed to connect to the packet manager to gain access to the packet shared memory.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-PAK_RECONNECT Failed to re-connect to packet manager: [chars]
Explanation The raw process failed to re-connect to the packet manager after the packet manager restarted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-PTHREAD_CREATE Failed to create the signal handling thread : [chars]
Explanation The raw process failed to create the signal handling thread.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-PTHREAD_SIGMASK Failed to set the signal mask : [chars]
Explanation The raw process failed to set the signal mask for the signal handling thread.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-RED_REGISTER Failed to register for node state change: [chars]
Explanation The raw process failed to register with System Manager for the node state changes.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-REG_NETWORK Failed to register RAW protocol with the network layer ([chars]): [chars]
Explanation The RAW transport failed to register itself with the network process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-RESMGR_ATTACH Failed to attach resmgr for [chars]: [chars]
Explanation The RAW transport failed to attach the resource manager pathname which allows application to create socket to it.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-SHOW_EDM_SERVER [chars]: [chars]
Explanation Error in the raw_show edm server side.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-SOCKET_NETWORK_INIT Failed to attach socket handlers for network events
Explanation The raw process failed to attach handlers for network events, or failed to create and initialize socket timers.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-SOCKET_PULSE_ATTACH Failed to attach handler for pakio pulse: [chars]
Explanation The raw process failed to attach handler for pulse from appl to send the packet out.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-SOFTWARE_INSTALL [chars]: [chars]
Explanation An error is encountered when the RAW process attempts to register with Install Manager for notification of software package installation and deinstallation on the system.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-SYSDB_BIND Failed to connect to SysDB at [chars]: [chars]
Explanation The raw process failed to connect to SysDB server. This connection can later be used to set/retrieve configuration information or to register for notification of certain tuple changes.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-SYSDB_INIT Failed to register for SysDB notification
Explanation The raw process failed to register with SysDB to get notification when network protocol creates the tuple for the network pathname.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-SYSDB_NOTIF_REGISTER Failed to register with SysDB the RAW notification functions: [chars]
Explanation The raw process failed to register with SysDB sever its notification functions which will be invoked whenever there are changes to any of RAW configuration tuples.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-SYSDB_VERIF_REGISTER Failed to register with SysDB the RAW verification functions: [chars]
Explanation The raw process failed to register with SysDB sever its verification functions which will be invoked whenever there are changes to any of RAW configuration tuples.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-SYSMGR_PROC_AVAIL Failed to declare to System Manager that RAW is available: [chars]
Explanation The RAW transport called sysmgr_proc_available() to declare its availability, but the function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-THREADPOOL_CREATE Failed to initialize the thread-pool attributes structure: [chars]
Explanation The raw process failed to initialize the thread-pool attributes structure which is used to manage the different threads.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-TIMER_INIT [chars]: [chars]
Explanation An error is encountered when the RAW process sets up and initializes the various RAW timers.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-3-TRANSP_DLLLOAD Failed to load [chars] network layer dll: [chars]
Explanation The RAW transport failed to load network layer DLLs.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RAW-4-DEBUG_OPEN Failed to open console device to write debug information: [chars]
Explanation The raw process failed to open the console to write debug information. Therefore, RAW will not use the console for debug output.
Recommended Action Debug message only. No action is required.
Error Message%IP-RAW-4-DEBUG_WRITE [chars]
Explanation The raw process failed to write debug information to either the console device or a debug file.
Recommended Action Debug message only. No action is required.
Error Message%IP-RAW-4-INVALID_COMMAND [chars]
Explanation The raw process detected an invalid command has been received.
Recommended Action Debug message only. No action is required.
Error Message%IP-RAW-4-NETDUMP_REGISTER Failed to register with the netdump debugging library: [chars]
Explanation The raw process failed to register with the netdump debugging library which creates and initializes the client debug structure that is used in subsequent debug calls.
Recommended Action Debug message only. No action is required.
Error Message%IP-RAW-4-NETDUMP_REWIND [chars]
Explanation The raw process failed to rewind (close and then open again) a file for writing debug information.
Recommended Action Debug message only. No action is required.
rlogin Messages
Error Message%IP-rlogin-3-CHILD_PID [chars]: [chars]
Explanation rlogin client application's child process has invalid pid
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%IP-rlogin-3-CHILD_STOPPED [chars]: the child stopped with signal number [dec]
Explanation rlogin client application's child process was stopped abnormally
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%IP-rlogin-3-CHILD_TERMINATED [chars]: the child terminated with signal number [dec]
Explanation rlogin client application's child process terminated abnormally.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%IP-rlogin-3-ERR_BEST_ROUTE No route to destination host exists
Explanation Socket operation failed.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%IP-rlogin-3-ERR_CREATE_EVENTMGR Couldn't create evmgr
Explanation Internal error.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%IP-rlogin-3-ERR_FLUSH tcflush failed
Explanation tcflush() call failed.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%IP-rlogin-3-ERR_FORK Can't fork child process
Explanation Internal error in forking child process.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%IP-rlogin-3-ERR_SOCKET socket: [chars]
Explanation Socket operation failed.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%IP-rlogin-3-WAIT [chars]: [chars]
Explanation rlogin client's call to wait() system call failed
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%IP-rlogin-6-ERR_GENRAL [chars]
Explanation The rlogin encountered some problem in genric nature or plain information.
Recommended Action 'No action is required.'
RLOGIND Messages
Error Message%IP-RLOGIND-3-ERR_CREATE_EVENTMGR Couldn't create evmgr in function [chars]()
Explanation Internal error.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%IP-RLOGIND-3-ERR_DEBUG_INIT Failed to init debug in function [chars]()
Explanation Internal error.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%IP-RLOGIND-3-ERR_FATAL Rlogind: fatal error [chars]
Explanation Fatal error.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%IP-RLOGIND-3-ERR_MALLOC Cannot allocate memory in function [chars]()
Explanation Internal error. System is out of memory - malloc failed.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%IP-RLOGIND-3-ERR_OPEN Failed to open a device file for a session ([dec])
Explanation An unexpected error occurred when RloginD tried to open a VTY character special file.
Recommended Action No action is required.
Error Message%IP-RLOGIND-3-ERR_SPAWN Can't spawn login
Explanation Internal error in spawning login child process.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%IP-RLOGIND-3-ERR_SYSDB Unexpected SysDB error encountered: [hex], '[chars]'
Explanation The Telnet Server has encountered an error using the SysDB Library.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RLOGIND-3-ERR_TTY_DETAILS Failed to retrieve the details of a TTY Device ([hex], '[chars]')
Explanation An unexpected error occurred when RloginD tried to retrieve the details of a VTY from a utility library
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RLOGIND-3-ERR_USAGE usage : rlogind [-alnd]
Explanation Usage error.
Recommended Action 'No action is required.'
Error Message%IP-RLOGIND-3-ERR_VTY_CONNECT Failed to obtain a VTY for a session: '[chars]'
Explanation An error occurred when RloginD requested a VTY for a session. This might occur if the requested rlogin session cannot be satisfied by any of the unused VTYs in the configured vty pool(s), e.g. if all VTYs are in use, if transport-input is not allowed for rlogin, or if the configured ACL does not match.
Recommended Action Check that the configured VTY pool(s) can satisfy this rlogin request based on which VTYs are currently in use. This can be checked with 'show users', and looking at the VTY pool configuration. If the configuration appears to be consistent then try to rlogin with debug rlogin detail on; this might indicate where the problem lies.
Error Message%IP-RLOGIND-4-ERR_SOCKET Socket operation failed: [chars]
Explanation Internal warnings related to socket operations.
Recommended Action 'No action is required.'
Error Message%IP-RLOGIND-6-INFO_GENERAL Rlogind: [chars]
Explanation The rlogind encountered some problem in genric nature or plain information.
Recommended Action 'No action is required.'
RSHD Messages
Error Message%IP-RSHD-2-ILLEGAL_PORT Illegal port: [chars]
Explanation The connection between rsh client and server must from/to a privileged port (512-1023)
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RSHD-3-ERR_AUTH Kerberos rsh denied to [chars].[chars]@[chars]
Explanation Kerberos authentication failed.
Recommended Action No action is required.
Error Message%IP-RSHD-3-ERR_CREATE_EVENTMGR Failed to create event manager: [chars]
Explanation Attempt to create an event manager fails for some reason
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RSHD-3-ERR_MALLOC Failed to allocate [dec] bytes of memory: [chars]
Explanation The server has failed to acquire the required amount of memory
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%IP-RSHD-3-ERR_REGISTER_DEBUG Failed to register for debugging events: [chars]
Explanation Attempt to register with the event magager for debugging events fails
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RSHD-3-ERR_SOCKET Socket operation failed: [chars]: [chars]
Explanation Internal warnings related to socket operations
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-RSHD-3-ERR_USAGE [chars]
Explanation Usage error.
Recommended Action No action is required.
SMIAP Messages
Error Message%IP-SMIAP-2-INIT_FAILED Cannot initialize [chars]: ([chars])
Explanation IPV4 SMIAP initialization failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-SMIAP-4-ADDR_CFLCT IP address [chars] configured on management interface [chars] same as virtual IP address [chars]
Explanation IP address on the management interface specified is conflicting with the virtual IP address.
Recommended Action Either change the virtual IP address to some other IP address on the management interface's network or change the conflicting IP address on the specified management interface.
Error Message%IP-SMIAP-4-IM_ATTR_FIND_IF_FAILED Interface '[chars]' is supposed to be a management interface, but, can't find information about it
Explanation Management interface information needs to be known in SMIAP so that it can make the virtual IP address functional.
Recommended Action If the message is for a management interface which doesn't exist anymore, e.g., due to a failover, this error can be simply ignored. If it is for an interface which is active, contact technical support.
Error Message%IP-SMIAP-4-INVALID_NETWORK IP address [chars]/[dec] on the management interface [chars] does not belong to same network as virtual IP address [chars]/[dec]
Explanation IP address on the management interface on the active/standby RP should be in the same network as the virtual IP address.
Recommended Action Change the IP address on the management interface or the virtual IP address so that they are in the same network and are not the same.
Error Message%IP-SMIAP-4-SYSMGR_FAILURE Failed to signal sysmgr about - [chars], error [chars]
Explanation SMIAP failed to signal sysmgr about its process state.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-SMIAP-4-VIRTUAL_IP_CFLCT Virtual IP address [chars] same as [chars] configured on management interface [chars]
Explanation IP address on the management interface specified is conflicting with the virtual IP address.
Recommended Action Either change the virtual IP address to some other IP address on the management interface's network or change the conflicting IP address on the specified management interface.
SOCKET Messages
Error Message%IP-SOCKET-3-DEBUG_INIT_EVENT Failed to initialize debug event: [chars]
Explanation The socket failed to initialize debug event.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-SOCKET-3-DEBUG_REGISTER Failed to register with debug library: [chars]
Explanation Failed to register with the debug library to have the library automatically handle changes to any of the SOCKET debug flags.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-SOCKET-3-EVENT_MANAGER_CREATE Failed to create event manager: [chars]
Explanation The socket failed to create event manager.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-SOCKET-7-ERR_PLIB_INIT Failed to initialize [chars] protocol library
Explanation None at this time
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-SOCKET-7-ERR_SBAPPEND Socket buffer overflow appending [hex] bytes, [hex] left
Explanation None at this time
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-SOCKET-7-ERR_SBAPPENDADDR Socket buffer overflow appending [hex] bytes, [hex] left
Explanation None at this time
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
STANDBY Messages
Error Message%IP-STANDBY-1-DEBUG_INIT_FAILED Failed to register debug: [chars]
Explanation The HSRP process failed to initialize its debug capabilities.
Recommended Action If the error persists, copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-STANDBY-3-ADDR_CONFLICT The new IP address [chars] on [chars] conflicts with the existing standby group [dec] on [chars]
Explanation A configuration external to HSRP, which is in conflict with the HSRP configuration.
Recommended Action Check the most recent configuration commands against the HSRP configuration.
Error Message%IP-STANDBY-3-BADAUTH Bad authentication from [chars], remote state [chars]
Explanation Two routers participating in the Hot Standby protocol disagree on the valid authentication string.
Recommended Action Use the standby authentication interface command to repair the Hot Standby protocol authentication discrepancy between the local system and the one whose IP address is reported.
Error Message%IP-STANDBY-3-BADTIMERS Bad timers from [chars], hello time [dec] seconds, hold time [dec] seconds
Explanation A router participating in the Hot Standby protocol is broadcasting invalid timer values.
Recommended Action Check the configuration of the peer HSRP router and correct the invalid timer values.
Error Message%IP-STANDBY-3-DATA_FORMAT Incorrect internal data format for extracting [chars] parameter(s): [chars]
Explanation The configuration command was accepted, but the data was passed in to wrong format to HSRP. This is an internal error.
Recommended Action Provide the command sequence which led to this error mesasge, copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-STANDBY-3-DEBUG_FAILURE Outputting debug information failed: [chars]
Explanation The HSRP process failed to output a debug message. This is an internal error.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-STANDBY-3-DUPADDR Received Packet with duplicate address [chars] on [chars]
Explanation The IP address in an HSRP message received on the interface is the same as the router's own interface IP address. This may be because of misconfiguration, or because of a malfunctioning switch.
Recommended Action Check the configurations on all the HSRP routers, and make sure that any switches you have are functioning properly.
Error Message%IP-STANDBY-3-GENERIC_ERROR [chars]: [chars]
Explanation A generic internal error has occurred.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-STANDBY-3-INITIALIZATION_FAILURE Initialization failed: [chars]: [chars]
Explanation The HSRP process failed to initialize correctly. This is an internal error.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-STANDBY-3-IP_CONFLICT_LOCAL SB[dec]: [chars]: Address [chars] is already assigned to an interface or another application
Explanation The HSRP process has failed to learn the virtual IP address for this group due to a conflict with a previously configured virtual IP address.
Recommended Action Reconfigure the conflicting group's virtual IP address on the source router or the real IP address that it conflicts with. If this fails copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-STANDBY-3-IP_CONFLICT_VIRTUAL SB[dec]: [chars]: Address [chars] is already assigned to [chars] group [dec]
Explanation The HSRP process has failed to learn the virtual IP address for this group due to a conflict with a previously configured or learned virtual IP address.
Recommended Action Reconfigure one of the conflicting group's virtual IP address. If this fails copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-STANDBY-3-JOIN_FAILURE [chars] request failed: [chars]: [chars]
Explanation The HSRP process failed to start/stop receiving HSRP packets on an interface correctly. This is an internal error.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-STANDBY-3-LOOKUP_IP_ADDR SB[dec]: [chars]: Internal lookup [chars] ip address [chars] failed
Explanation The software couldn't find the ip address in its internal data structures.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-STANDBY-3-NO_PRIMARY_ADDRESS SB[dec]: [chars]: secondary IP address has been configured with no primary IP address present
Explanation There is no primary address for the standby group but a secondary address. has been accepted. This is an internal error.
Recommended Action Provide the command sequence which led to this error mesasge, copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-STANDBY-3-NOMEM No memory available for setup
Explanation There was no memory available for setting up the system.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-STANDBY-3-REGISTER_FAILED Registration for [chars] failed: [chars]
Explanation Registration for some system service failed during HSRP initialization
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-STANDBY-3-RPC_GET_FAIL RPC get failure, failed to get [chars] information
Explanation The HSRP show process failed to get information from the main HSRP process.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-STANDBY-3-SCAN_CONFIG Configuration scan failed: [chars]
Explanation The standby process was unable to read the configuration data.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-STANDBY-3-SECONDARY_ADDRESS_NOT_DELETED SB[dec]: [chars]: primary IP address has been unconfigured with secondary ip address [chars] still present
Explanation When the primary virtual IP address is unconfigured, the system should take care of removing all secondary addresses, but the code has detected at least one that is still present. This is an internal error.
Recommended Action Provide the command sequence which led to this error mesasge, copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-STANDBY-3-SHOW_INIT_FAIL [chars] [text]
Explanation HSRP register RPC client failed during initialization on SHOW command
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-STANDBY-3-SNMPINDEX Failed to obtain snmp index for [chars]: [chars]
Explanation The HSRP process failed to obtain snmp index for this interface. This has been caused by a temporary lack of system resources.
Recommended Action Retry the configuration on this interface. If this fails copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-STANDBY-3-SYSDB_BIND [chars] could not bind to sysdb: [chars]
Explanation The configuration command was accepted, but it should not have been. This is an internal error.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-STANDBY-3-SYSDB_TO_CONNID Could not determine the HSRP [chars] connection id: [chars]
Explanation The standby process was unable to compute the internal variable for communticating with the sysdb. This is an internal error.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-STANDBY-3-UNKNOWN_CONTROL_MESSAGE Received an unknown message on [chars] type [dec]
Explanation The hsrp process received a message of unknown type.
Recommended Action The HSRP process received an unknown control message with the IP packet.
Error Message%IP-STANDBY-3-VIP_MISMATCH SB[dec]: [chars]: Address [chars] not the same as the Active's address [chars] on [chars]
Explanation The HSRP process has detected a virtual IP address mismatch within this HSRP group.
Recommended Action Reconfigure the virtual IP addresses on all routers in this HSRP group such that the virtual IP addresses match. Alternatively, the configured address can be deleted so that it will be learnt from the Active router. If this fails copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-STANDBY-6-BADPACKETLEN Discarding packet, received too few bytes ([dec] bytes)
Explanation Not enough bytes in the packet received
Recommended Action Obtain a line trace to determine source of bad packet.
Error Message%IP-STANDBY-6-LOW_HOLDTIME Holdtime is less than or equal to twice the hellotime
Explanation The holdtime has been set to a value which is less than (or equal to) twice the hello time, this is not recommended.
Recommended Action Change the holdtime to be greater than twice the hellotime.
Error Message%IP-STANDBY-6-REDIRECTS_DISABLED ICMP redirects may still be enabled on this interface
Explanation Disabling HSRP filtered ICMP redirects when ICMP redirects are enabled may cause hosts to use real IP addresses as their default routes, and first hop redundancy may be lost.
Recommended Action Ensure that ICMP redirects are disabled on this interface.
Error Message%IP-STANDBY-6-REDIRECTS_SECONDARY ICMP redirects may be ignored by hosts if HSRP secondary addresses are used
Explanation If a host uses HSRP secondary addresses, HSRP filtered ICMP redirects may be ignored by the host (depending on the host implementation).
Recommended Action Try to avoid using HSRP secondary addresses when HSRP filtered ICMP redirects are enabled.
Error Message%IP-STANDBY-6-STATECHANGE SB[dec]: [chars]: state [chars]011 - [chars]
Explanation The router has changed state
Recommended Action No action is required.
TCP Messages
Error Message%IP-TCP-3-ADD_PP Failed to insert the [chars] PCB proto into the PP list
Explanation The TCP transport failed to add the pcb protocol to a global list.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-CMD_EDM_INIT [chars] [chars]
Explanation The tcp process was not able to setup an EDM for show tcp commands.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-DEBUG_INIT_EVENT Failed to initialize debug event: [chars]
Explanation tcp transport failed to initialize debug event.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-DUMMY_SOCKET [chars] ([chars]): [chars]
Explanation The tcp process failed to create or update the dummy socket which is used for sending TCP RST segments.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-EDM_INIT [chars]: [chars]
Explanation The tcp process was not able to setup an EDM for show ip traffic.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-ERR_IM [chars]: [chars]
Explanation A Interface Manager function which is called by the tcp process had failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-ERR_PTHREAD_CREATE TCP failed to create signal handler thread: [chars]
Explanation The TCP process could not create signal handler thread.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-ERR_PTHREAD_SIGMASK TCP failed to set sigmask: [chars]
Explanation The TCP process failed to set up the sigmask for all the signal it interested in.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-EVENT_ATTACH Failed to attach a handler for [chars]: [chars]
Explanation The tcp process failed to attach a handler function to handle a specific event.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-EVM_CREATE Failed to create event manager: [chars]
Explanation The tcp process failed to create an event manager channel.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-GET_DB_VECTOR Failed to get the [chars] database vector
Explanation The TCP transport failed to get the network database vector.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-GET_NONPCB_VECTOR Failed to get [chars] non-PCB family vector: [chars]
Explanation The TCP transport failed to get the non-PCB network function vector.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-GET_PCB_VECTOR Failed to get [chars] PCB family vector: [chars]
Explanation The TCP transport failed to get the PCB network function vector.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-HSSD_REGISTER Failed to register HSSD with packet manager. Error [chars] returned.
Explanation The ip pcb failed to register with packet manager for the vrfid HSSD which is used by FIB for table lookup.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-IM_LOOKUP Failed to lookup [chars] [chars] from IM: [chars]
Explanation The TCP transport failed to lookup a network attribute from the Inteface Manager.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-INIT_RETRY [chars] ([dec])
Explanation An error is encountered when the TCP process attempts to retry one of its initialization tasks with a network layer.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-LIST_CREATE Failed to create a tcp protocol list
Explanation The tcp process failed to create a list to hold tcp protocol queues.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-MIB_CACHE_INIT Failed to init mib cache mutex. Error [chars] returned
Explanation tcp transport failed to initialize mib cache mutex.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-MUTEX_LOCK [chars]: [chars]
Explanation The TCP transport failed to lock a particular mutex.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-NO_MEM [chars] ([chars]): [chars]
Explanation The TCP transport failed to allocate memory for some data structure.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-NODE_STATE Failed to get the current state of this node: [chars]
Explanation The tcp process failed to obtain the current state of this node to determine whether it's active or not.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-PAK_CONNECT TCP failed to connect to packet manager: [chars]
Explanation The tcp process failed to connect to the packet manager to gain access to the packet shared memory.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-RED_REGISTER Failed to register for node state change: [chars]
Explanation The tcp process failed to register with System Manager for the node state changes.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-REG_NETWORK Failed to register TCP protocol with the network layer ([chars]): [chars]
Explanation The TCP transport failed to register itself with the network process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-RESMGR_ATTACH Failed to attach resmgr for [chars]: [chars]
Explanation The TCP transport failed to attach the resource manager pathname which allows application to create socket to it.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-SOCKET_NETWORK_INIT Failed to attach socket handlers for network events
Explanation The tcp process failed to attach handlers for network events, or failed to create and initialize socket timers.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-SOCKET_PULSE_ATTACH Failed to attach handler for pakio pulse: [chars]
Explanation The tcp process failed to attach handler for pulse from appl to send the packet out.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-SYSMGR_PROC_AVAIL Failed to declare to System Manager that TCP is available: [chars]
Explanation The TCP transport called sysmgr_proc_available() to declare its availability, but the function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-SYSMGR_PROC_READY Failed to notify sysmgr the completion of init. Error [chars] returned
Explanation tcp transport failed to notify sysmgr process that tcp transport completed the initialization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-THREADPOOL_CREATE TCP failed to initialize the thread-pool attributes structure: [chars]
Explanation The tcp process failed to initialize the thread-pool attributes structure which is used to manage the different threads.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-TIMER_INIT [chars]: [chars]
Explanation An error is encountered when the TCP process sets up and initializes the various TCP timers.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-TRACE_ERR [chars] error ([dec]). Premature trace termination for control block 0x[pointer]
Explanation Error message for premature trace termination.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-3-TRANSP_DLLLOAD Failed to load [chars] network layer dll: [chars]
Explanation The TCP transport failed to load network layer DLLs.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-4-WARNING [chars] [dec]
Explanation Warning messages from TCP.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TCP-7-ERR_TCP_INIT TCP failed to initialize: [chars], error [chars]
Explanation TCP initialization failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
telnet Messages
Error Message%IP-telnet-3-ARM_ADDRESS Error: [chars]
Explanation 'The call to ip_addr_c_get_v4/v6_best() failed'
Recommended Action *SH_TECH*
Error Message%IP-telnet-3-ERR_SYSDB Unexpected SysDB error encountered: [hex], '[chars]'
Explanation The Telnet client has encountered an error using the SysDB Library.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-telnet-3-INTF_DOWN Specified source interface is down
Explanation 'The source interface is down, therefore it can not be used.'
Recommended Action *SH_TECH*
Error Message%IP-telnet-3-INTF_HANDLE The interface handle for the source interface is invalid
Explanation 'The call to interface_find() returned invalid interface handle'
Recommended Action *SH_TECH*
Error Message%IP-telnet-3-INVALID_ADDR_FAMILY Invalid adress family: [dec]
Explanation 'The api has returned invalid address family'
Recommended Action *SH_TECH*
Error Message%IP-telnet-3-INVALID_ADDRESS Source interface has an invalid address
Explanation 'The call to ip_addr_c_get_v4/v6_best() returned an invalid address'
Recommended Action *SH_TECH*
Error Message%IP-telnet-3-INVALID_INTF The specified source interface is invalid
Explanation 'The specified source interface can not be used. Will use default interface'
Recommended Action *SH_TECH*
Error Message%IP-telnet-3-INVALID_PORT Error converting the port number to numerical representation: [chars]
Explanation 'The port specified on the command line can not be converted'
Recommended Action *SH_TECH*
Error Message%IP-telnet-3-IP_ARM Error: [chars]
Explanation 'The call to ip_addr_c_init() failed'
Recommended Action *SH_TECH*
Error Message%IP-telnet-3-RIB_BIND_FAILURE Unable to bind to the RIB
Explanation An error occurred while attempting to bind to the RIB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-telnet-3-RIB_SRC_ADDRESS_ERROR Error retrieving source address from RIB: [chars]. Cannot continue.
Explanation An error occured while trying to retrieve the IP address of the source interface from the RIB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-telnet-3-SYSDB_GET [chars]: [chars]
Explanation 'Unable to get/read an item from sysDB '
Recommended Action *SH_TECH*
Error Message%IP-telnet-3-SYSTEM_ERROR Error in [chars]. errno [dec]: [chars]
Explanation 'There was an error during invocation of a system call'
Recommended Action *SH_TECH*
Error Message%IP-telnet-3-TCP_NETWORK_COMMS Error communicating with the network: [chars] Exiting.
Explanation An error occurred whilst trying to set an option on the TCP socket used for this connection.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. The router can continue to be used.
Error Message%IP-telnet-3-TTY_DETAILS [chars]: [chars]
Explanation 'The call to tty_details_from_device_file() failed '
Recommended Action *SH_TECH*
Error Message%IP-telnet-3-TTY_NMSPC_PATH [chars]: [chars]
Explanation 'Unable to get the sysDB path of an item from TTY nmspc library'
Recommended Action *SH_TECH*
Error Message%IP-telnet-4-TCP_NAGLE Failed to disable Nagle's algorithm during socket initialisation: [chars];
Explanation Nagle's algorithm was not disabled; there is a small chance the telnet session will appear jerky. Telnet will otherwise function normally.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. The router can continue to be used.
TELNETD Messages
Error Message%IP-TELNETD-2-SYSTEM_FAIL [chars]: [chars] errno=[dec] [chars]
Explanation There was a critical system call failure resulting in a failure to provide some system service.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-TELNETD-3-ERR_ADDRESS_FAMILY The address family [dec] is invalid
Explanation The telnetd server was passed a bad adress family.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TELNETD-3-ERR_BAD_PORT Bad port number
Explanation The telnetd server was passed a bad port number.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TELNETD-3-ERR_CONNECT Failed to obtain a VTY for a session: '[chars]'
Explanation An error occurred when TelnetD requested a VTY for a session. This might occur if the requested telnet session cannot be satisfied by any of the unused VTYs in the configured vty pool(s), e.g. if all VTYs are in use, if transport-input is not allowed for telnet, or if the configured ACL does not match.
Recommended Action Check that the configured VTY pool(s) can satisfy this telnet request based on which VTYs are currently in use. This can be checked with 'show users', and looking at the VTY pool configuration. If the configuration appears to be consistent then try to telnet with debug telnet detailed on; this might indicate where the problem lies.
Error Message%IP-TELNETD-3-ERR_CREATE_EVENTMGR Couldn't create evmgr in function [chars]()
Explanation Internal error.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%IP-TELNETD-3-ERR_DEBUG_INIT Failed to init debug in function [chars]()
Explanation Internal error.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%IP-TELNETD-3-ERR_EXITING Function cleanup() has been called due to an error
Explanation The Telnet Server has encountered an unexpected error while using the system library.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TELNETD-3-ERR_KERNEL [chars]: The call to [chars] failed. Error: [hex], '[chars]'
Explanation The Telnet Server has encountered an unexpected error while using the system library.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TELNETD-3-ERR_MALLOC Failed to allocate [dec] bytes of memory
Explanation The server has failed to acquire the required amount of memory
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%IP-TELNETD-3-ERR_OPEN Failed to open a device file for a session ([dec])
Explanation An unexpected error occurred when TelnetD tried to open a VTY character special file.
Recommended Action No action is required.
Error Message%IP-TELNETD-3-ERR_PANIC telnetd: panic state = [dec]
Explanation Panic error.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%IP-TELNETD-3-ERR_SYSDB Unexpected SysDB error encountered: [hex], '[chars]'
Explanation The Telnet Server has encountered an error using the SysDB Library.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TELNETD-3-ERR_TTY_DETAILS Failed to retrieve the details of a TTY Device ([hex], '[chars]')
Explanation An unexpected error occurred when TelnetD tried to retrieve the details of a VTY from a utility library
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TELNETD-3-ERR_USAGE usage : telnetd -debug -no_tty_server
Explanation Usage error.
Recommended Action 'No action is required.'
Error Message%IP-TELNETD-3-SYSTEM_ERROR Error: [chars]
Explanation The invocation of a system call returned error condition.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-TELNETD-3-TCP_NETWORK_COMMS Error communicating with the network: [chars] Exiting.
Explanation An error occurred whilst trying to set an option on the TCP socket used for this connection.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. The router can continue to be used.
Error Message%IP-TELNETD-4-CONFIGURATION_CHECK [chars]: Warning - configuration inconsistencies
Explanation The configuration inconsistencies is detected for the indicated configuration.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-TELNETD-4-TCP_KEEPALIVE Failed to set the TCP keepalive timeout during socket initialisation: [chars]; default will apply
Explanation The TCP keepalive timeout was not set during initialisation. The default value of 2 hours will apply. Telnet will otherwise function normally.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. The router can continue to be used.
Error Message%IP-TELNETD-4-TCP_NAGLE Failed to disable Nagle's algorithm during TCP socket initialisation: [chars];
Explanation Nagle's algorithm was not disabled; there is a small chance the telnet session will appear jerky. Telnet will otherwise function normally.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. The router can continue to be used.
UDP Messages
Error Message%IP-UDP-3-ADD_PP Failed to insert the [chars] PCB proto into the PP list
Explanation The UDP transport failed to add the pcb protocol to a global list.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-CMD_EDM_INIT [chars]: [chars]
Explanation The udp process was not able to setup an EDM for show udp commands.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-DEBUG_INIT_EVENT Failed to initialize debug event: [chars]
Explanation The udp failed to initialize debug event.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-DEBUG_REGISTER Failed to register with debug library: [chars]
Explanation The udp process failed to register with the debug library to have the library automatically handle changes to any of the UDP debug flags.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-EDM_INIT [chars]: [chars]
Explanation The udp process was not able to setup an EDM for show ip traffic.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-END_PROC Unexpected process termination, [chars]
Explanation The udp process terminated unexpectedly. This may be caused by: 1. failure to start a thread pool 2. a SIGTERM, SIGINT or SIGHUP signal is received
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-EVM_CREATE Failed to create event manager: [chars]
Explanation The udp process failed to create an event manager channel.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-FSV_REGISTER Failed to register with packet manager to use the FSV
Explanation The udp process failed to register with packet manager for the FSV which is used between the IP [v4/6] I/O and its transport.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-GET_DB_VECTOR Failed to get the [chars] database vector
Explanation The UDP transport failed to get the network database vector.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-GET_NONPCB_VECTOR Failed to get [chars] non-PCB family vector: [chars]
Explanation The UDP transport failed to get the non-PCB network function vector.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-GET_PCB_VECTOR Failed to get [chars] PCB family vector: [chars]
Explanation The UDP transport failed to get the PCB network function vector.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-HSSD_REGISTER Failed to register HSSD with packet manager. Error [chars] returned
Explanation The ip pcb failed to register with packet manager for the vrfid HSSD which is used by FIB for table lookup.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-INIT_RETRY [chars]([dec])
Explanation An error is encountered when the UDP process attempts to retry one of its initialization tasks with a network layer.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-LIST_CREATE Failed to create a udp protocol list
Explanation The udp process failed to create a list to hold udp protocol queues.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-LOAD_DLL Failed to load the library dll for [chars] [chars]
Explanation The udp process failed to load a library dll.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-LPTS_TRANSP_INIT Failed to initialize and establish a channel with LPTS Port Arbitrator
Explanation The Udp protocol process failed to open a connection with Port Arbitrator and create the edm thread for 'show udp pcb'
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-MIB_CACHE_INIT Failed to init mib cache mutex. Error [chars] returned
Explanation udp transport failed to initialize mib cache mutex.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-MUTEX_LOCK [chars]: [chars]
Explanation The UDP transport failed to lock a particular mutex.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-NO_MEM [chars] ([chars]): [chars]
Explanation The UDP transport failed to allocate memory for some data structure.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-NODE_STATE Failed to get the current state of this node: [chars]
Explanation The udp process failed to obtain the current state of this node to determine whether it's active or not.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-PAK_CONNECT Failed to connect to packet manager: [chars]
Explanation The udp process failed to connect to the packet manager to gain access to the packet shared memory.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-PAK_RECONNECT Failed to re-connect to packet manager: [chars]
Explanation The udp process failed to re-connect to the packet manager after the packet manager restarted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-PTHREAD_CREATE Failed to create the signal handling thread : [chars]
Explanation The udp process failed to create the signal handling thread.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-PTHREAD_SIGMASK Failed to set the signal mask : [chars]
Explanation The udp process failed to set the signal mask for the signal handling thread.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-RED_REGISTER Failed to register for node state change: [chars]
Explanation The udp process failed to register with System Manager for the node state changes.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-REG_NETWORK Failed to register UDP protocol with the network layer ([chars]): [chars]
Explanation The UDP transport failed to register itself with the network process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-RESMGR_ATTACH Failed to attach resmgr for [chars]: [chars]
Explanation The UDP transport failed to attach the resource manager pathname which allows application to create socket to it.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-SOCKET_NETWORK_INIT Failed to attach socket handlers for network events
Explanation The udp process failed to attach handlers for network events, or failed to create and initialize socket timers.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-SOCKET_PULSE_ATTACH Failed to attach handler for pakio pulse: [chars]
Explanation The udp process failed to attach handler for pulse from appl to send the packet out.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-STATS_INIT Failed to initialize UDP statistics data structures: [chars]
Explanation The udp process failed to initialize data structures that are used to keep track of UDP MIB statistics.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-SYSDB_BIND Failed to connect to SysDB at [chars]: [chars]
Explanation The udp process failed to connect to SysDB server. This connection can later be used to set/retrieve configuration information or to register for notification of certain tuple changes.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-SYSDB_INIT Failed to register for SysDB notification
Explanation The udp process failed to register with SysDB to get notification when network protocol creates the tuple for the network pathname.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-SYSDB_NOTIF_REGISTER Failed to register with SysDB the UDP notification functions: [chars]
Explanation The udp process failed to register with SysDB sever its notification functions which will be invoked whenever there are changes to any of UDP configuration tuples.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-SYSDB_VERIF_REGISTER Failed to register with SysDB the UDP verification functions: [chars]
Explanation The udp process failed to register with SysDB sever its verification functions which will be invoked whenever there are changes to any of UDP configuration tuples.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-SYSMGR_PROC_AVAIL Failed to declare to System Manager that UDP is available: [chars]
Explanation The UDP transport called sysmgr_proc_available() to declare its availability, but the function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-SYSMGR_PROC_READY Failed to notify sysmgr the completion of init. Error [chars] returned
Explanation udp transport failed to notify sysmgr process that udp transport completed the initialization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-THREADPOOL_CREATE Failed to initialize the thread-pool attributes structure: [chars]
Explanation The udp process failed to initialize the thread-pool attributes structure which is used to manage the different threads.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-TIMER_INIT [chars]: [chars]
Explanation An error is encountered when the UDP process sets up and initializes the various UDP timers.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-3-TRANSP_DLLLOAD Failed to load [chars] network layer dll: [chars]
Explanation The UDP transport failed to load network layer DLLs.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%IP-UDP-4-DEBUG_OPEN Failed to open console device to write debug information: [chars]
Explanation The udp process failed to open the console to write debug information. Therefore, UDP will not use the console for debug output.
Recommended Action Debug message only. No action is required.
Error Message%IP-UDP-4-DEBUG_WRITE [chars]
Explanation The udp process failed to write debug information to either the console device or a debug file.
Recommended Action Debug message only. No action is required.
Error Message%IP-UDP-4-INVALID_COMMAND [chars]
Explanation The udp process detected an invalid command has been received.
Recommended Action Debug message only. No action is required.
Error Message%IP-UDP-4-NETDUMP_PRINT_CONTEXT Failed to print the udp netdump context: [chars]
Explanation The udp process failed to write to the console device the process debug context which is mainly debug parameters.
Recommended Action Debug message only. No action is required.
Error Message%IP-UDP-4-NETDUMP_REGISTER Failed to register with the netdump debugging library: [chars]
Explanation The udp process failed to register with the netdump debugging library which creates and initializes the client debug structure that is used in subsequent debug calls.
Recommended Action Debug message only. No action is required.
Error Message%IP-UDP-4-NETDUMP_REWIND [chars]
Explanation The udp process failed to rewind (close and then open again) a file for writing debug information.
Recommended Action Debug message only. No action is required.
VRRP Messages
Error Message%IP-VRRP-3-DEBUG_FAILURE Outputting debug information failed: [chars]
Explanation The VRRP process failed to output a debug message.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-VRRP-3-INIT_FAILURE Initialization failed: [chars]: [chars]
Explanation The VRRP process failed to initialize correctly.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-VRRP-3-REGISTER_FAILED Registration for [chars] failed: [chars]
Explanation Registration for a system service failed during VRRP initialization.
Recommended Action Retry the command just issued. Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%IP-VRRP-6-STATECHANGE [chars] vrid [dec]: state [chars]011 - [chars]
Explanation The VRRP router has changed state.
No action is required.
