This document provides a sample configuration for the use of the VLAN ACL (VACL) Capture Port feature for network traffic analysis in a more granular manner. This document also states the advantage of VACL capture-port usage as opposed to VLAN-based SPAN (VSPAN) usage.
In order to configure the VACL capture-port feature on Cisco Catalyst 6000/6500 that runs Catalyst OS software, refer to VACL Capture for Granular Traffic Analysis with Cisco Catalyst 6000/6500 Running CatOS Software.
Ensure that you meet these requirements before you attempt this configuration:
The information in this document is based on these software and hardware versions: Cisco Catalyst 6506 Series Switch that runs Cisco IOS® Software Release 12.2(18)SXF8.
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
This configuration can also be used with Cisco Catalyst 6000 / 6500 Series Switches that run Cisco IOS Software Release 12.1(13)E and later.
Refer to Cisco Technical Tips Conventions for more information on document conventions.
SPAN (Switched Port ANalyzer) copies traffic from one or more source ports in any VLAN or from one or more VLANs to a destination port for analysis. Local SPAN supports source ports, source VLANs, and destination ports on the same Catalyst 6500 Series Switch.
A source VLAN is a VLAN monitored for network traffic analysis. VLAN-based SPAN (VSPAN) uses a VLAN as the SPAN source. All the ports in the source VLANs become source ports. A source port is a port monitored for network traffic analysis. Trunk ports can be configured as source ports and mixed with nontrunk source ports, but SPAN does not copy the encapsulation from a source trunk port.
For VSPAN sessions with both ingress and egress configured, two packets are forwarded from the destination port if the packets get switched on the same VLAN (one as ingress traffic from the ingress port and one as egress traffic from the egress port).
VSPAN only monitors traffic that leaves or enters Layer 2 ports in the VLAN.
If you configure a VLAN as an ingress source and traffic gets routed into the monitored VLAN, the routed traffic is not monitored because it never appears as ingress traffic that enters a Layer 2 port in the VLAN.
If you configure a VLAN as an egress source and traffic gets routed out of the monitored VLAN, the routed traffic is not monitored because it never appears as egress traffic that leaves a Layer 2 port in the VLAN.
For more information on source VLANs, refer to Characteristics of Source VLAN.
VACLs can provide access control for all packets that are bridged within a VLAN or that are routed into or out of a VLAN or a WAN interface for VACL capture. Unlike regular Cisco IOS standard or extended ACLs that are configured on router interfaces only and are applied on routed packets only, VACLs apply to all packets and can be applied to any VLAN or WAN interface. VACLs are processed in hardware. VACLs use Cisco IOS ACLs. VACLs ignore any Cisco IOS ACL fields that are not supported in hardware.
You can configure VACLs for IP, IPX, and MAC-Layer traffic. VACLs applied to WAN interfaces support only IP traffic for VACL capture.
When you configure a VACL and apply it to a VLAN, all packets that enter the VLAN are checked against this VACL. If you apply a VACL to the VLAN and an ACL to a routed interface in the VLAN, a packet that comes into the VLAN is first checked against the VACL and, if permitted, is then checked against the input ACL before it is handled by the routed interface. When the packet is routed to another VLAN, it is first checked against the output ACL that is applied to the routed interface, and, if permitted, the VACL configured for the destination VLAN is applied. If a VACL is configured for a packet type and a packet of that type does not match the VACL, the default action is deny. These are the guidelines for the capture option in VACL.
The capture port cannot be an ATM port.
The capture port needs to be in the spanning-tree forwarding state for the VLAN.
The switch has no restriction on the number of capture ports.
The capture port captures only packets permitted by the configured ACL.
Capture ports only transmit traffic that belongs to the capture port VLAN. Configure the capture port as a trunk that carries the required VLANs in order to capture traffic that goes to many VLANs.
Caution: Incorrect combination of ACLs can disrupt the traffic flow. Exercise extra caution while you configure the ACLs in your device.
Note: VACL is not supported with IPv6 on a Catalyst 6000 series switch. In other words, VLAN ACL redirect and IPv6 are not compatible so ACL cannot be used to match IPv6 traffic.
There are several limitations of VSPAN usage for traffic analysis:
All layer 2 traffic that flows in a VLAN is captured. This increases the amount of data to be analyzed.
The number of SPAN sessions that can be configured on the Catalyst 6500 Series Switches is limited. Refer to Local SPAN and RSPAN Session Limits for more information.
A destination port receives copies of sent and received traffic for all monitored source ports. If a destination port is oversubscribed, it can become congested. This congestion can affect traffic forwarding on one or more of the source ports.
The VACL Capture Port feature can help to overcome some of these limitations. VACLs are primarily not designed to monitor traffic, but, with a wide range of capability to classify the traffic, the Capture Port feature was introduced so that network traffic analysis can become much simpler. These are the advantages of VACL Capture Port usage over VSPAN:
Granular Traffic Analysis
VACLs can match based on source IP address, destination IP address, Layer 4 protocol type, source and destination Layer 4 ports, and other information. This capability makes VACLs very useful for granular traffic identification and filtering.
Number of Sessions
VACLs are enforced in hardware; the number of Access Control Entries (ACE) that can be created depends upon the TCAM available in the switches.
Destination Port Oversubscription
Granular traffic identification reduces the number of frames to be forwarded to the destination port and thereby minimizes the probability of their oversubscription.
VACLs are enforced in hardware; there is no performance penalty for the application of VACLs to a VLAN on the Cisco Catalyst 6500 Series Switches
In this section, you are presented with the information to configure the features described in this document.
Note: Use the Command Lookup Tool (registered customers only) to find more information on the commands used in this document.
This document uses this network setup:
This configuration example lists the steps required to capture all Layer 2 traffic that flows in VLAN 100 and VLAN 200 and send them to the Network Analyzer device.
Specify the interesting traffic. In our example, it is traffic that flows in VLAN 100 and VLAN 200.
Cat6K-IOS(config)#monitor session 50 source vlan 100 , 200 ?
, Specify another range of VLANs
- Specify a range of VLANs
both Monitor received and transmitted traffic
rx Monitor received traffic only
tx Monitor transmitted traffic only
!--- Default is to monitor both received and transmitted traffic
Cat6K-IOS(config)#monitor session 50 source vlan 100 , 200
Specify the destination port for the captured traffic.
Cat6K-IOS(config)#monitor session 50 destination interface Fa3/30
With this, all the layer 2 traffic that belongs to VLAN 100 and VLAN 200 is copied and sent to port Fa3/30. If the destination port is part of the same VLAN whose traffic is monitored, the traffic that goes out of the destination port is not captured.
Verify your SPAN configuration with the show monitor command.
Cat6K-IOS#show monitor detail
Type : Local Session
Source Ports :
RX Only : None
TX Only : None
Both : None
Source VLANs :
RX Only : None
TX Only : None
Both : 100,200
Source RSPAN VLAN : None
Destination Ports : Fa3/30
Filter VLANs : None
Dest RSPAN VLAN : None
In this configuration example, there are multiple requirements from the network administrator:
HTTP Traffic from a range of hosts (10.20.20.128/25) in VLAN 200 to a specific server (10.10.10.101) in VLAN 100 needs to be captured.
Multicast User Datagram Protocol (UDP) traffic in the transmit direction destined for group address 184.108.40.206 needs to be captured from VLAN 100.
Define the interesting traffic to be caputured and sent to analysis.
Cat6K-IOS(config)#ip access-list extended HTTP_UDP_TRAFFIC
Cat6K-IOS(config-ext-nacl)#permit tcp 10.20.20.128 0.0.0.127 host 10.10.10.101 eq www
Cat6K-IOS(config-ext-nacl)#permit udp any host 220.127.116.11
Define an umberlla ACL to map all other traffic.
Cat6K-IOS(config)#ip access-list extended ALL_TRAFFIC
Cat6K-IOS(config-ext-nacl)#permit ip any any
Define the VLAN access map.
Cat6K-IOS(config)#vlan access-map HTTP_UDP_MAP 10
Cat6K-IOS(config-access-map)#match ip address HTTP_UDP_TRAFFIC
Cat6K-IOS(config-access-map)#action forward capture
Cat6K-IOS(config)#vlan access-map HTTP_UDP_MAP 20
Cat6K-IOS(config-access-map)#match ip address ALL_TRAFFIC
Apply the VLAN access map to the appropriate VLANs.
Cat6K-IOS(config)#vlan filter HTTP_UDP_MAP vlan-list 100
!--- Here 100 is the ID of VLAN on which the VACL is applied.
Configure the Capture Port.
Cat6K-IOS(config-if)#switchport capture allowed vlan ?
WORD VLAN IDs of the allowed VLANs when this po
add add VLANs to the current list
all all VLANs
except all VLANs except the following
remove remove VLANs from the current list
Cat6K-IOS(config-if)#switchport capture allowed vlan 100
Use this section to confirm that your configuration works properly.
The Output Interpreter Tool (registered customers only) (OIT) supports certain show commands. Use the OIT to view an analysis of show command output.
There is currently no specific troubleshooting information available for this configuration.