Guest

Cisco ONS 15454 Series Multiservice Transport Platforms

Cisco Transport Node Controller and Transport Shelf Controller Cards Data Sheet

  • Viewing Options

  • PDF (360.0 KB)
  • Feedback

Product Overview

The Cisco Network Convergence System (NCS) 2000 Series, the Cisco ONS 15454 Multiservice Transport Platform (MSTP), and the Cisco Carrier Packet Transport platform share a common set of controller cards which perform system initialization, provisioning, alarm reporting, maintenance, diagnostics, IP addressing, data-communications-channel (DCC) termination, monitoring of system input voltage, system fault detection, and multishelf management connections. The line cards include the:

   Cisco ONS 15454 Transport Node Controller (TNC) Card

   Cisco ONS 15454 Transport Shelf Controller (TSC) Card

   Cisco ONS 15454 Enhanced Transport Node Controller (TNCE) Card

   Cisco ONS 15454 Enhanced Transport Shelf Controller (TSCE) Card

   Cisco NCS 2000 Series Transport Node Controller (TNCS) Card

The TNC, TNCE and TNCS cards feature two optical service channel (OSC) ports that support a supervisory data channel (SDC), distribution of synchronous clocking, and a 100-Mbps user data channel (UDC). The TNCE, TSCE, and TNCS cards support the IEEE1588v2 Precision Timing Protocol (PTP) and time of day (ToD) with pulse per second (PPS), in addition to supporting Synchronous Ethernet (SyncE)/source-specific multicast (SSM). This is summarized in Table 1.

Table 1.       Controller Card Feature Differentiation

Controller Card

Include two OSC Ports

Support PTP and ToD with PPS

TSC

No

No

TSCE

No

Yes

TNC

Yes

No

TNCE

Yes

Yes

TNCS

Yes

Yes

Common Features

All controller card versions incorporate a highly stable Layer 3 internal timing reference to provide system timing based on input received from an external BITS source or from an incoming SONET or SDH optical signal. Synchronous status messaging helps the system select the best timing sources, and a holdover mode maintains timing accuracy when preprovisioned synchronization references are not available.

Figure 1.      Cisco ONS 15454 TNC Card

Nonvolatile database storage for communication, provisioning, and system control is provided, allowing full database recovery and survivability with complete system power loss. In addition, short-term clock recovery is also supported, reducing the need to reset the calendar and ToD settings after a brownout or complete power outage. A memory module is built into each ONS 15454 MSTP and NCS 2000 Series chassis and synchronized with the memory of the cards, thereby providing a backup to the node IP address, software package, and circuit database. This synchronization provides faster time to recovery when the node is used in simplex mode during a control-card replacement.

The cards have two built-in interface ports for accessing the system: an RJ-45 connector and an RS-232. The RJ-45 port provides 10BASE-T Ethernet connectivity to the system, providing local and remote access to the craft-management system, Cisco Transport Controller, through a common web interface. You can also use this port for interconnection to customer operations support systems (OSSs) and network management systems (NMSs), providing integration to external element management systems (EMSs), NMSs, and OSSs.

The cards provide enhanced security by allowing you to configure the front panel and chassis Ethernet interfaces as regenerators or provision them with individual IP and MAC addresses for segregated craft and DCC access. The RS-232 port provides a serial ASCII interface for local craft access using VT100 emulation so that you can enter Transaction Language 1 (TL1) commands directly over a Telnet session without the assistance of a browser.

The front panels of the cards multicolored LEDs for a quick view of the card activity status, raised network alarms, shelf voltage input, LAN interface, and synchronization. Two front-panel buttons allow you to quiet an active external audible alarm (alarm-cutoff button) or test the working state of system LEDs.

In the Cisco Network Convergence System 2015 (NCS 2015), Network Convergence System 2006 (NCS 2006), Cisco ONS 15454 M6 Multiservice Transport Platform (MSTP), and Cisco Carrier Packet Transport (CPT) 600, the cards can be equipped as active and standby, providing 1:1 equipment protection. In the Cisco Network Convergence System 2002 (NCS 2002), Cisco ONS 15454 M2 MSTP, and Cisco Carrier Packet Transport (CPT) 200, a single card is used in simplex mode.

Features and Benefits

The Cisco ONS 15454 TNC, TSC, TNCE, TSCE, and NCS 2000 Series TNCS cards provide the following features:

   Integrated optical service channel (OSC): Each ONS 15454 TNC, TNCE, or TNCS card can be configured with one or two SFP ports to provide the OSC termination. In addition to OC-3/STM-1, the OSC can be configured with Fast Ethernet or Gigabit Ethernet for increased bandwidth and compatibility in future packet transport architectures.

   Integrated multishelf management: The ONS 15454 TNC, TNCE, TSC, TSCE, and TNCS cards - coupled with the external connection unit (ECU) of the ONS 15454 M6, NCS 2006, or NCS 2015 - can support up to 50 subtended shelves in a cascade configuration without using an external switch or separate Ethernet switch card.

   Eighty-four section DCC (SDCC) and multiplex section DCC (MSDCC) terminations allow the interconnection of multiring and linear systems on a single-shelf assembly, reducing networking costs.

   Eighty-four SDCC tunnels or SDCC-to-line DCC (LDCC) tunnels provide interface flexibility for transparent transport of third-party DCC overhead channels.

   Integrated system input-voltage monitoring facilitates proactive identification of DC power-system problems.

   Time-and-date clock recovery after brownout or power loss prevents clock reprogramming.

   A complete shelf lamp test through a faceplate pushbutton simplifies technician LED maintenance testing.

   Local and remote craft user access allows technicians to access nodes from anywhere.

   Local audible alarm cutoff squelches office audible or visual alert systems.

   Through the Cisco ONS 15454 M6 External Connection Unit (ECU), the cards support connection to up to six subtended shelves or to the master shelf.

   The cards support up to 24 dry-contact external alarms.

   IEEE1588v2 Precision Timing Protocol with ToD and PPS is supported by the enhanced ONS 15454 TNCE and TSCE cards, as well as the TNCS card.

Feature Availability

Table 2 outlines the feature availability supported on the Cisco ONS 15454 TNC, TSC, TNCE, TSCE, and NCS 2000 Series TNCS cards.

Table 2.       Feature Availability

Feature

Availability

DCC terminations

84 SDCC and MSDCC terminations

DCC tunnels

28 SDCC tunnels or LDCC terminations

OC-3/STM-1:

  DCC D1-D3 = 194 kbps implemented
  DCC D4-D12 = 576 kbps implemented
  UDC/VoIP 100 kbps (Packet over SONET into VC-4 payload)

Gigabit Ethernet (the 1-Gbps payload is shared)

  Data Communications Network (DCN) variable bandwidth (maximum: 100 Mbps)
  VoIP/UDC variable bandwidth (maximum: 100 Mbps)

Generic communications channel (GCC)

160 GCCs

GCC0 may be ~350 kbps (OTU1), ~1.3 Mbps (OTU2), 5.2 Mbps (OTU3), ~12 Mbps (OTU4)

BITS timing

1.544 MHz, 2.08 MHz, 6.312 MHz, 64 kHz, and 10 MHz

ONS 15454 TNCE and TSCE add IEEE1588v2 PTP, 10 MHz, and 1 PPS

Optical service channel (OSC) using the ONS 15454 TNC, TNCE, or TNCS card

Two SFP ports

Port 1 can be OC-3/STM-1, Fast Ethernet, or Gigabit Ethernet

Port 2 can be Fast Ethernet or Gigabit Ethernet

SFP options

ONS-SC-OSC-ULH=

SFP: OC-3/STM-1 or Fast Ethernet OSC SFPs

Ultra long-haul (ULH): Commercial temperature

ONS-SE-155-1510=

SFP: OC-3/STM-1, coarse wavelength-division multiplexing (CWDM), 1510 nm, EXT

ONS-SC-Z3-1510=

SFP: OC-48/STM-16 or Gigabit Ethernet, CWDM, 1510 nm

Product Specifications

Tables 3 and 4 outline the specifications for the Cisco ONS 15454 TNC, TSC, TNCE, TSCE, and NCS 2000 Series TNCS cards.

Table 3.       Product Specifications

Compliance

Countries

Canada

European Union

Hong Kong

Japan

Korea

Mexico

United States

Australia

China

European Union

Hong Kong

Korea

Mexico

New Zealand

Singapore

Electromagnetic compliance (EMC) - Class A

ETSI 300-386-TC Telcordia Technologies Network Equipment Building Standards (NEBS) GR-1089-CORE, Issue 3 (Level 3, Type 2 and Type 4)

CISPR 22, CISPR 24

IC ICES-003 Issue 3, 1997

FCC 47CFR15

EN55022, EN55024

Product safety

Telcordia Technologies NEBS GR-1089-CORE, Issue 3 Level IEC 60950-1/EN 60950-1, 1st Edition UL and cUL/CSA 60950-1 1st Edition (Level 3, Type 2 and Type 4)

Environmental

Telcordia Technologies NEBS GR-63-CORE, Level 3

ETS 300 019-2-1 (Storage, Class 1.1)

ETS 300 019-2-2 (Class 2.3)

ETS 300 019-2-3 (Class 3.1E)

Customer requirements

AT&T Network Equipment Design Specification (NEDS)

Verizon TCG Checklist

MCI/Worldcom ESD

Table 4.       Product Specifications (All Cards)

Attribute

Value

Hardware Components

Processor speed

1 GHz

Nonvolatile memory (Flash)

4 GB

Volatile memory (synchronous dynamic RAM)

1 GB

Physical Card Interfaces

LAN

RJ-45 and 10BASE-T Ethernet

Craft

DB-9, RS-232 serial, and data terminal equipment (DTE)

TL1

9.6 K baud

Management

Card LEDs

 

Failure (FAIL)

Red

Status (ACT/STBY)

Green/yellow

System LEDs

 

Critical (CRIT)

Red

Major (MAJ)

Red

Minor (MIN)

Yellow

Remote (REM)

Red

Synchronization (SYNC)

Green

Alarm cutoff (ACO)

Green

Power A (PWR-A)

Green/amber/red

Power B (PWR-B)

Green/amber/red

Port LEDs

 

LAN link (LINK)

Green

LAN activity (ACT)

Amber (flash)

Input Voltage Monitoring (per input)

For -48 VDC nominal systems

  Less than -40.5 VDC
  -40.5 to -56.7 VDC
  Greater than -56.7 VDC

For -60 VDC nominal systems

  Less than -50.0 VDC
  -50.0 to -72.0 VDC
  Greater than -72.0 VDC

GR-499-CORE and ETS 300 132-2

  Major alarm, red LED
  Normal, green LED
  Major alarm, red LED

ETS 300 132-2 Annex A

  Major alarm, red LED
  Normal, green LED
  Major alarm, red LED

Power

Maximum

120W

Physical

Size (H x W x D)

Single card slot: 12.65 x 0.72 x 9.00 in. (32.13 x 1.83 x 22.86 cm)

Weight

2.05 lb (0.93 kg)

Operating Environment

Temperature

-40 to 149°F (-40 to 65°C)

Humidity

5 to 95%, noncondensing

Storage Environment

Temperature

-40 to 185°F (40 to 85°C)

Humidity

5 to 95%, noncondensing

System Requirements

Table 5 outlines the system requirements for the Cisco ONS 15454 TNC, TSC, TNCE, TSCE, and Cisco NCS 2000 Series TNCS cards.

Table 5.       System Requirements

Component

NCS 2015

NCS 2006
ONS 15454 M6

NCS 2002
ONS 15454 M2

CPT 600

CPT 200

Processor Configuration

1+1 or single

1+1 or single

single

1+1 or single

single

Chassis and Software

 

 

 

 

 

TNC/TSC

-

Release 9.2.0 or later

Release 9.2.0 or later

Release 9.2.0 or later

Release 9.2.0 or later

TNCE/TSCE

 

Release 9.3.0 or later

Release 9.3.0 or later

Release 9.3.0 or later

Release 9.3.0 or later

TNCS

10.5 or later

-

-

-

-

Shelf-slot compatibility

1 and 17

1 and 8

1

1 and 8

1

Ordering Information

Table 6 lists the ordering information for the Cisco ONS 15454 TNC, TSC, TNCE, TSCE, and NCS 2000 Series TNCS cards. To place an order, visit the Cisco Ordering Home Page and refer to Table 5. To download software, visit the Cisco Software Center. http://www.cisco.com/cisco/software/type.html?mdfid=278281788&i=rm

Table 6.       Ordering Information

Product Description

Part Number

Transport Node Controller for NCS 2002, 2006 and 2015 chassis

NCS2K-TNCS-K9

Transport Node Controller for M2, M6 chassis

15454-M-TNC-K9

Transport Shelf Controller for M2, M6 chassis

15454-M-TSC-K9

Enhanced Transport Node Controller for M2, M6, CPT200, CPT600

15454-M-TNCE-K9

Enhanced Transport Shelf Controller for M2, M6, CPT200, CPT600

15454-M-TSCE-K9

Cisco Services

Cisco offers a wide range of services programs to help accelerate customer success. These innovative services programs are delivered through a unique combination of people, processes, tools, and partners, promoting high levels of customer satisfaction. Cisco Services can help you protect your network investment, optimize network operations, and prepare your network for new applications to extend network intelligence and the power of your business. For more information about Cisco Services, refer to Cisco Technical Support Services or Cisco Advanced Services.

Cisco Capital

Financing to Help You Achieve Your Objectives

Cisco Capital can help you acquire the technology you need to achieve your objectives and stay competitive.
We can help you reduce CapEx. Accelerate your growth. Optimize your investment dollars and ROI. Cisco Capital financing gives you flexibility in acquiring hardware, software, services, and complementary third-party equipment. And there’s just one predictable payment. Cisco Capital is available in more than 100 countries. Learn more.

For More Information

For more information about the Cisco Optical Solution, visit http://cisco.com/en/US/products/hw/optical/ps2006/index.html or contact your local Cisco account representative.