ISDN Digital Subscriber Line (IDSL) is een huurlijn ISDN Basic Rate Interface (BRI) die niet wordt geschakeld en geen signalering (een D-kanaal) bevat. IDSL en ISDN BRI gebruiken dezelfde 2B1Q lijnmodulatie. Op de router, staat dit gelijk aan de plaatsing van de BRI interface in een huurlijnconfiguratie. U kunt de lijn configureren voor een snelheid van 64 kbps, 128 kbps of 144 kbps.
De frames die over de draad gaan zijn standaard HDLC-frames (Data Link Control Control). U kunt PPP of Frame Relay insluiting voor de huurlijn BRI-interface configureren. Beschouw de BRI interface als een synchrone seriële poort die bij een lage snelheid draait.
Deze items zijn vereist voor gebruik van IDSL:
Een router die de ISDN huurlijn mondiale configuratieopdracht ondersteunt en een BRI interface heeft.
Een digitale Subscriber Line Access Multiplexer (DSLAM) met IDSL-interfaces om de andere kant van de verbinding te beëindigen.
Momenteel heeft Cisco acht-poorts IDSL-kaarten om in Cisco 6160 DSLAM te gebruiken. Ondersteuning van de 6130 DSLAM is gepland. Het verschil is dat Cisco 6130 slechts vier poorten per IDSL-kaart ondersteunt.
Snelheid en insluiting die overeenkomen met de DSLAM-configuratie.
Er zijn slechts een paar soorten DSLAM’s voor IDSL. Het is daarom gemakkelijk om verbinding te maken met de apparatuur van andere leveranciers.
Slechts één buis bij 64 kbps, 128 kbps of 144 kbps.
Cisco ondersteunt geen BRI-interface die in twee huurlijnen wordt gekanaliseerd.
De informatie in dit document is gebaseerd op de volgende software- en hardware-versies:
Cisco 804 apparatuur voor klanten (CPE) IOS ® softwarerelease 12.0(7)T
Cisco 6400 UAC-routeprocessor voor knooppunt (NRP) IOS-softwarerelease 12.0(7)DC
Cisco UCS 6400 UAC-Switch processor (NSP) IOS-softwarerelease 12.0(4)DB
Cisco 1630 DSLAM-NI2 IOS-softwarerelease 12.1(1)DA
De informatie in dit document is gebaseerd op de apparaten in een specifieke laboratoriumomgeving. Alle apparaten die in dit document worden beschreven, hadden een opgeschoonde (standaard)configuratie. Als uw netwerk live is, moet u de potentiële impact van elke opdracht begrijpen.
In deze sectie wordt uitgelegd hoe u een CPE voor een externe gebruiker kunt configureren.
In deze sectie wordt u gepresenteerd met de informatie die u kunt gebruiken om de functies te configureren die in dit document worden beschreven.
N.B.: Gebruik het Opdrachtupgereedschap (alleen geregistreerde klanten) om meer informatie te vinden over de opdrachten die in dit document worden gebruikt.
Het netwerk in dit document is als volgt opgebouwd:
Om een router met een BRI interface voor IDSL te configureren voert u deze stappen uit:
Voeg deze opdrachten toe:
isdn leased-line bri [#] [128|144] ! interface bri [#] no shut !
Op dit punt komt de regel omhoog, maar niet het lijnprotocol (zoals een seriële poort).
Geef de ISDN-statusopdracht niet uit. Het is irrelevant omdat er geen D-kanaal is. Het laat soms zien dat Layer 1 omlaag is wanneer het niet omlaag is.
Geef een show int bri[#] opdracht uit en volg de regels van een seriële interface in termen van lijnprotocol en lijnstatus.
Voeg de configuratie van PPP of Frame Relay toe.
Dit voorbeeld toont de PPP configuratie:
isdn leased-line bri 0 128 ! username b-nrp password 0 cisco !--- b-nrp is the username assigned to the ISDN router !--- to authenticate with the ISP. !--- cisco is the password assigned to the ISDN router !--- to authenticate with the ISP. ! ! interface BRI0 ip address 7.7.7.2 255.255.255.0 encapsulation ppp ppp authentication chap !
Deze twee voorbeelden tonen de configuratie van Frame Relay. Zorg ervoor dat u de insluiting van Internet Engineering Task Force (IETF) gebruikt.
Voorbeeld 1
! interface BRI0/0 ip address 10.0.0.1 255.255.255.0 no ip directed-broadcast encapsulation frame-relay IETF fair-queue 64 16 0 frame-relay map ip 10.0.0.2 300 broadcast IETF frame-relay lmi-type ansi !
Voorbeeld 2
! interface BRI0/0 no ip address no ip directed-broadcast encapsulation frame-relay IETF fair-queue 64 16 0 frame-relay lmi-type ansi ! interface BRI0/0.300 point-to-point ip address 10.0.0.2 255.255.255.0 no ip directed-broadcast frame-relay interface-dlci 300 IETF !
Opmerking: Onthoud dat er geen signalering, dialer interface, dialer lijsten, dialer strings en geen dialer maps zijn. Dit is een speciale lijn zoals een speciale T1 serielijn. Het enige verschil is dat de 2B1Q-modulatie wordt gebruikt in plaats van V.35, dat wordt gebruikt voor de gegevensservice-eenheid/kanaalservicekeenheid (DSU/CSU).
Als het lijnprotocol niet voor PPP op komt, geeft u deze debug opdrachten uit:
debug van PPP-onderhandeling
debug van PPP-verificatie
fout PPP-fout debug
De NI2 DSLAM-configuratie veronderstelt een kennis van een DSL- en ATM-configuratie, die PPP over ATM (PPPoA) omvat. De configuratie van IDSL is grondiger dan een asymmetrische digitale abonneelijn (ADSL) of een digitale abonneelijn (SDSL).
Om IDSL-kaarten in de DSLAM te kunnen gebruiken, is Cisco IOS-softwarerelease 12.1(2)DA of hoger vereist.
Op DSLAM worden de ADSL- en SDSL-interfaces in de configuratie als ATM-interfaces weergegeven. De Cisco-implementaties van ADSL en SDSL gebruiken ATM. IDSL gebruikt echter HDLC-frames om gegevens te transporteren. Als resultaat hiervan verschijnen de interfaces als IDSL interfaces in de configuratie.
Voor één IDSL-kaart in een Cisco 6160 DSLAM lijkt de configuratie op deze uitvoer:
! interface IDSL3/1 no ip address no logging event link-status no arp frame-relay ! interface IDSL3/2 no ip address no logging event link-status no arp frame-relay ! interface IDSL3/3 no ip address no logging event link-status no arp frame-relay ! interface IDSL3/4 no ip address no logging event link-status no arp frame-relay ! interface IDSL3/5 no ip address no logging event link-status no arp frame-relay ! interface IDSL3/6 no ip address no logging event link-status no arp frame-relay ! interface IDSL3/7 no ip address no logging event link-status no arp frame-relay ! interface IDSL3/8 no ip address no logging event link-status no arp frame-relay !
Opmerking: NI1 DSLAM-platforms ondersteunen IDSL niet en er is geen plan om deze ondersteuning te bieden.
Voor elke IDSL-interface is er een pseudo-ATM-interface. Op de hardware worden de HDLC-frames geconverteerd naar ATM-cellen voordat ze zijn ingeschakeld door de NI2 ATM-fabric.
Voor PPP, definieer een permanent virtueel circuit (PVC) dat een bestemmingsteken virtuele pad-id (VPN) en virtueel kanaal-id (VCI) heeft. Een bron-VCI/VPI is niet vereist omdat er slechts één verbinding voor PPP is.
Voor Frame Relay, stelt u zestien PVC’s in, die zich vertalen in zestien datalink-verbindingsidentificatoren (DLCI’s). De configuratie omvat de levering van een bron-DLCI-nummer en een bestemming VPN/VCI-paar.
Er zijn twee belangrijke stappen in een DSL-configuratie. Voor de PPP-configuratie zijn ze:
Stel het DSL-profiel in.
Stel het PVC/SVC in onder de IDSL-interface.
Stel daarnaast QoS (Quality of Service) in voor de IDSL-link, zodat de ATM-bronnen die naar de IDSL-poorten gaan, correct worden gebruikt. Bereken de overhead voor ATM-framing. In deze tabel wordt het maximale ATM-piekaantal/duurzame celsnelheid (PCR/solvabiliteitskapitaalvereiste) weergegeven dat u voor het equivalente IDSL-bitrate moet configureren.
IDSL-bitsnelheid ingesteld (kbps) | Max. ATM PCR/solvabiliteitskapitaalvereiste (kbps) |
---|---|
56 | 71 |
64 | 81 |
128 | 163 |
144 | 183 |
Deze PPP-opties zijn beschikbaar voor het IDSL-profiel:
idsl bitrate [56 | 64 | 128 | 144] idsl encapsulation [cisco-ppp | llc-ppp | mux-ppp ]
De bitrate moet overeenkomen met de bitrate van de CPE. De insluiting wijst het type PPPoA-insluiting aan dat bij de aggregator eindigt.
Dit is de syntaxis die wordt gebruikt om een PVC te maken dat verbinding maakt met de verbinding IDSL PPP:
ppp pvc interface atm 0/x [VPI] [VCI]
Er is geen input PVC omdat de PPP-link slechts één verbinding heeft. ATM 0/x is de ATM-buis uit de DSLAM naar de aggregator.
Gebruik deze wereldwijde opdracht om QoS-parameters op te zetten. Gebruik de PCR-/solvabiliteitstabel voor pcr- en scr10-waarden.
atm connection-traffic-table-row index [row #] vbr-nrt pcr [#] scr10 [#]
Om deze waarden op het IDSL-PVC toe te passen, verander ppp pvc interface atm 0/x [VPI] [VCI] naar ppp pvc interface atm 0/x [VPI] [VCI] rx-cttr [rij #] tx-cttr [rij #] .
Een PPP IDSL-configuratie die 128 Kbps en LC-p insluiting voor de aggregator gebruikt, is:
atm connection-traffic-table-row index 128 vbr-nrt pcr 163 scr10 163 ! dsl-profile idsl1 idsl encapsulation llc-ppp !--- 128 kbps is the default. ! ! interface IDSL3/1 dsl profile idsl1 ppp pvc interface ATM0/1 3 300 rx-cttr 128 tx-cttr 128 !
Als DSLAM voor insluiting is geconfigureerd voor MLC-ppp onder het IDSL-profiel (of er is niets ingesteld voor insluiting omdat dit standaard is) moet de aggregator deze configuratie hebben:
! interface ATM0/0/0.300 point-to-point no ip directed-broadcast pvc 3/300 encapsulation aal5snap protocol ppp Virtual-Template10 ! !
Als DSLAM voor insluitingscisco-PPP is geconfigureerd, wijzigt u de configuratie in:
! interface ATM0/0/0.300 point-to-point no ip directed-broadcast pvc 3/300 encapsulation aal5ciscoppp Virtual-Template10 ! !
Als DSLAM voor mux-ppp van de insluiting van IDSL is geconfigureerd, moet u ervoor zorgen dat de configuratie op de aggregator:
! interface ATM0/0/0.300 point-to-point no ip directed-broadcast pvc 3/300 encapsulation aal5mux ppp Virtual-Template10 ! !
Voor de configuratie van Frame Relay zijn de twee belangrijke stappen hetzelfde als in de PPP-configuratie.
Stel het DSL-profiel in.
Stel het PVC/SVC in onder de IDSL-interface.
Voor QoS op de Frame Relay-link is geen speciale conversie nodig. Stel het maximum tarief in de verbinding-tabel-rij zodat het de bandbreedte aanpast die op CPE wordt bepaald.
Voor het IDSL-profiel zijn dit de opties voor Frame Relay:
idsl bitrate [56 | 64 | 128 | 144] idsl frame-relay ? bc-default Default Bc in bytes lmi-n392dce LMI error threshold lmi-n393dce set LMI monitored event count lmi-t392dce set DCE polling verification timer lmi-type Use CISCO-ANSI-CCITT type LMI upc-intent UPC to use on Soft-VCs/PVCs
Om Frame Relay-insluiting in te schakelen, moet u ook de opdracht van het insluitingsframe en de relais van de insluiting toevoegen.
Deze syntaxis maakt een PVC dat verbinding maakt met de terminatie van IDSL Frame Relay:
frame-relay pvc [DLCI] service translation interface atm0/1 [VPI] [VCI]
Er is ook een transparante parameter die in dit document niet wordt besproken. Het vertaalsleutelwoord vertaalt Frame Relay DLCI gedefinieerd in het ATM PVC gedefinieerd. Het ATM PVC is een AAL5SNAP PVC.
Gebruik deze wereldwijde opdracht om de QoS-parameters op te zetten:
frame-relay connection-traffic-table-row index [row #] [CIR] [Burst] [PIR] vbr-rt
Standaard is CIR=PIR gelijk aan de bandbreedte die in het IDSL-profiel voor de link is gedefinieerd. De burst rate is gewoonlijk maximaal 32.768 bps.
Om deze waarden op het IDSL-PVC toe te passen, moet frame-relais pvc [DLCI] service-vertaalinterface atm0/1 [VPI] [VCI] op frame-relais pvc [DLCI] rx-cttr [rij #] tx-cttr [rij #] servicevertalingsinterface atm0/1 [VPI] [VCI].
Een Frame Relay IDSL-configuratie die 128 Kbps met libel-type ANSI gebruikt, is:
! dsl-profile idslframe idsl encapsulation frame-relay idsl frame-relay lmi-type ansi ! frame-relay connection-traffic-table-row index 128 128000 32768 128000 vbr-rt ! ! interface IDSL2/2 no ip address dsl profile idslframe no arp frame-relay frame-relay pvc 300 rx-cttr 128 tx-cttr 128 service translation interface ATM0/1 3 300 !
Voor Frame Relay-insluiting aan de CPE-zijde converteert de DSLAM het Frame Relay PVC naar een ATM PVC. Het ATM PVC wordt ingekapseld in AAL5SNAP.
Voor een routed Frame Relay PVC:
! interface ATM0/0/0.300 point-to-point ip address 10.0.0.1 255.255.255.0 pvc 3/300 encapsulation aal5snap protocol ip (inarp) broadcast ! !
Overeenkomstig met andere kaarten die in de DSLAM-fase zijn ingebracht, moet de IDSL-kaart waarschijnlijk handmatig in de NI2-configuratie worden aangewezen.
DSLAM(config)#slot 2 ituc-1-8IDSL
Nadat de IDSL-kaart is ingevoerd, geeft u een opdracht voor de status van de aan de kaart gedownload code weer.
DSLAM#show oir status 2 Slot 2: timer stopped delay 100 last heard 30348 ms ago, last sent 30348 ms ago Slot 2: loading. . . current offset 0x1CFD1, done at 0xBF858
Deze loguitvoer wordt gezien.
00:04:20: %SLOT-3-MODULE_DETECTED: CLEAR INFO Slot 2 Module was detected 00:04:45: %SLOT-3-MODULE_MISSING: CLEAR MAJOR Slot 2 Provisioned slot is empty 00:04:45: %SLOT-3-MODULE_DETECTED: ASSERT INFO Slot 2 Module was detected 00:04:48: %LINK-3-UPDOWN: Interface IDSL2/1 to IDSL2/8, changed state to down DSLAM#show hardware Chassis Type: C6160 Slot 1 : STUC-4-2B1Q-DIR-1 Slot 18: EMPTY Slot 2 : ITUC-1-8IDSL Slot 19: EMPTY Slot 3 : EMPTY Slot 20: EMPTY Slot 4 : EMPTY Slot 21: EMPTY Slot 5 : EMPTY Slot 22: EMPTY Slot 6 : EMPTY Slot 23: EMPTY Slot 7 : EMPTY Slot 24: EMPTY Slot 8 : EMPTY Slot 25: EMPTY Slot 9 : EMPTY Slot 26: EMPTY Slot 10: NI-2-155SM-DS3 Slot 27: EMPTY Slot 11: EMPTY Slot 28: EMPTY Slot 12: EMPTY Slot 29: EMPTY Slot 13: EMPTY Slot 30: EMPTY Slot 14: EMPTY Slot 31: EMPTY Slot 15: EMPTY Slot 32: EMPTY Slot 16: EMPTY Slot 33: EMPTY Slot 17: EMPTY Slot 34: EMPTY Fan Module: Present Power Supply Module 1: Present 2: Not Present
Deze sectie verschaft de informatie die u kunt gebruiken om problemen met uw configuratie op te lossen.
Bepaalde opdrachten met show worden ondersteund door de tool Output Interpreter (alleen voor geregistreerde klanten). Hiermee kunt u een analyse van de output van opdrachten met show genereren.
Opmerking: Voordat u debug-opdrachten afgeeft, raadpleegt u Belangrijke informatie over debug-opdrachten.
debug PPP onderhandeling-monitort PPP onderhandelingsgebeurtenissen.
debug van PPP-verificatie - Bepaalt als een client authenticatie passeert.
tonen DSL interface idl 2/2-displays IDSL en verbindingsstatistieken.
ATM vc interface tonen-Toont de pseudo ATM interface achter de IDSL-interface.
Laat gebruikers-Informatie over actieve gebruikers zien.
Als u een verbinding met IDSL PPP wilt oplossen, geeft u de debug PPP-onderhandeling uit en debug de opdrachten voor de verificatie van ppp. Voor een actieve verbinding, is dit de uitvoer van een opdracht van de showgebruikers
Router#show users Line User Host(s) Idle Location * 0 con 0 idle 00:00:00 Interface User Mode Idle Peer Address BR0/0 b-nrp Sync PPP 00:00:03 10.0.0.2
Op DSLAM, tonen deze opdrachten statistieken van IDSL en verbindingsstatistieken.
DSLAM#show dsl interface idsl 2/2 Port Status: Subscriber Name: Circuit ID: IOS admin: UP oper: UP Card status: ITUC-1-8IDSL Last Change: 00 days, 00 hrs, 07 min, 13 sec No. of changes: 1 Loopback: none Firmware version: 961170635 BERT has not been executed on this interface Configured: Profile Name: default Alarms Enabled: NO IDSL profile parameters Bitrate: 128 kbit/sec Encapsulation: llc-ppp Frame Relay parameters: UPC intent: pass Bc default: 32768 bytes LMI type: cisco lmi-n392dce: 2 events lmi-n393dce: 2 events lmi-t392dce: 15 seconds Performance Statistics: Physical layer Coding violations : 0 Errored seconds : 0 Severely errored seconds : 0 Physical layer (far end) Coding violations : 0 Errored seconds : 0 Severely errored seconds : 0 HDLC layer Coding violations : 0 Aborts : 0 Aligns : 0 Shorts : 5 Longs : 0 Discards : 42 Alarm Status: NONE
Merk op dat elke IDSL-interface een gekoppelde pseudo-ATM-interface achter heeft.
DSLAM#show atm vc interface atm-p 2/2 Interface VPI VCI Type X-Interface X-VPI X-VCI Encap Status ATM-P2/2 0 37 PVC ATM0/1 3 300 UP DSLAM#show atm vc interface atm-p 2/2 0 37 Interface: ATM-P2/2, Type: ATM-PSEUDO VPI = 0 VCI = 37 Status: UP Time-since-last-status-change: 00:02:24 Connection-type: PVC Cast-type: point-to-point Packet-discard-option: disabled Usage-Parameter-Control (UPC): pass Number of OAM-configured connections: 0 OAM-configuration: disabled OAM-states: Not-applicable Cross-connect-interface: ATM0/1, Type: suni_dual Cross-connect-VPI = 3 Cross-connect-VCI = 300 Cross-connect-UPC: pass Cross-connect OAM-configuration: disabled Cross-connect OAM-state: Not-applicable Rx cells: 27, Tx cells: 0 Rx connection-traffic-table-index: 128 Rx service-category: VBR-NRT (Non-Realtime Variable Bit Rate) Rx pcr-clp01: 163 Rx scr-clp01: 163 Rx mcr-clp01: none Rx cdvt: none Rx mbs: 1024 (from default for interface) Tx connection-traffic-table-index: 128 Tx service-category: VBR-NRT (Non-Realtime Variable Bit Rate) Tx pcr-clp01: 163 Tx scr-clp01: 163 Tx mcr-clp01: none Tx cdvt: none Tx mbs: none
U kunt ook het PVC van de andere zijde bekijken (van de aggregator naar de CPE).
DSLAM#show atm vc interface atm 0/1 3 300 Interface: ATM0/1, Type: suni_dual VPI = 3 VCI = 300 Status: UP Time-since-last-status-change: 00:03:20 Connection-type: PVC Cast-type: point-to-point Packet-discard-option: disabled Usage-Parameter-Control (UPC): pass Number of OAM-configured connections: 0 OAM-configuration: disabled OAM-states: Not-applicable Cross-connect-interface: ATM-P2/2, Type: ATM-PSEUDO Cross-connect-VPI = 0 Cross-connect-VCI = 37 Cross-connect-UPC: pass Cross-connect OAM-configuration: disabled Cross-connect OAM-state: Not-applicable Rx cells: 0, Tx cells: 68 Rx connection-traffic-table-index: 128 Rx service-category: VBR-NRT (Non-Realtime Variable Bit Rate) Rx pcr-clp01: 163 Rx scr-clp01: 163 Rx mcr-clp01: none Rx cdvt: none Rx mbs: 1024 (from default for interface) Tx connection-traffic-table-index: 128 Tx service-category: VBR-NRT (Non-Realtime Variable Bit Rate) Tx pcr-clp01: 163 Tx scr-clp01: 163 Tx mcr-clp01: none Tx cdvt: none Tx mbs: none
Deze sectie verschaft de informatie die u kunt gebruiken om problemen met uw configuratie op te lossen.
Bepaalde opdrachten met show worden ondersteund door de tool Output Interpreter (alleen voor geregistreerde klanten). Hiermee kunt u een analyse van de output van opdrachten met show genereren.
Opmerking: Voordat u debug-opdrachten afgeeft, raadpleegt u Belangrijke informatie over debug-opdrachten.
Statistieken van frame lmi-displays over de Local Management Interface (LMI).
debug frame lmi-bepaalt of LMI-pakketten correct verzonden en ontvangen worden.
toon frame-relais pvc-displays PVC statistieken voor Frame Relay interfaces.
tonen frame map—Hiermee geeft u de huidige map-items en informatie over de verbindingen weer.
toon frame-relais interfacebron-displays QoS parameters.
toon interface idl-displays Frame Relay statistieken.
ATM vc interface tonen-Toont de pseudo ATM interface achter de IDSL-interface.
Om een IDSL BRI poortverbinding in te lossen, gebruikt u de zelfde opdrachten die worden gebruikt om een seriële poort op te lossen.
Router#show frame lmi !--- Check for status messages received and Enq. sent. LMI Statistics for interface BRI0/0 (Frame Relay DTE) LMI TYPE = CISCO Invalid Unnumbered info 0 Invalid Prot Disc 0 Invalid dummy Call Ref 0 Invalid Msg Type 0 Invalid Status Message 0 Invalid Lock Shift 0 Invalid Information ID 0 Invalid Report IE Len 0 Invalid Report Request 0 Invalid Keep IE Len 0 Num Status Enq. Sent 71 Num Status msgs Rcvd 0 Num Update Status Rcvd 0 Num Status Timeouts 70
Time-outs betekenen dat er geen communicatie van de NI2-switch is.
Om te zuiveren, geeft de opdracht debug frame lmi uit op dezelfde manier als deze voor een seriële interface wordt gebruikt. U kunt ook de pvc van het showframe-relais uitgeven en de opdrachten van de frame-kaart tonen.
Router#show frame lmi LMI Statistics for interface BRI0/0 (Frame Relay DTE) LMI TYPE = ANSI Invalid Unnumbered info 0 Invalid Prot Disc 0 Invalid dummy Call Ref 0 Invalid Msg Type 0 Invalid Status Message 0 Invalid Lock Shift 0 Invalid Information ID 0 Invalid Report IE Len 0 Invalid Report Request 0 Invalid Keep IE Len 0 Num Status Enq. Sent 17 Num Status msgs Rcvd 18 Num Update Status Rcvd 0 Num Status Timeouts 0 Router#show frame-relay pvc PVC Statistics for interface BRI0/0 (Frame Relay DTE) Active Inactive Deleted Static Local 1 0 0 0 Switched 0 0 0 0 Unused 0 0 0 0 DLCI = 300, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = BRI0/0 input pkts 0 output pkts 0 in bytes 0 out bytes 0 dropped pkts 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 0 out bcast bytes 0 pvc create time 00:02:30, last time pvc status changed 00:02:30 Router#show frame map BRI0/0 (up): ip 10.0.0.2 dlci 300(0x12C,0x48C0), static, broadcast, IETF, status defined, active
Aan de kant van DSLAM kunt u ook een opdracht van het showframe uitgeven.
DSLAM#show frame-relay lmi interface idsl2/2 LMI Statistics for interface IDSL2/2 (Frame Relay DCE) LMI TYPE = ANSI Invalid Unnumbered info 0 Invalid Prot Disc 0 Invalid dummy Call Ref 0 Invalid Msg Type 0 Invalid Status Message 0 Invalid Lock Shift 0 Invalid Information ID 0 Invalid Report IE Len 0 Invalid Report Request 0 Invalid Keep IE Len 0 Num Status Enq. Rcvd 2 Num Status msgs Sent 2 Num Update Status Sent 0 Num St Enq. Timeouts 0
Om QoS parameters te zien, geef de opdracht van de show frame-relais interface uit.
DSLAM#show frame-relay interface resource idSL 2/1 Encapsulation: FRAME-RELAY Resource Management state: Available bit rates (in bps): 128000 vbr-nrt RX, 128000 vbr-nrt TX 128000 vbr-rt RX, 128000 vbr-rt TX 128000 ubr RX, 128000 ubr TX Allocated bit rates (in bps): 0 vbr-nrt RX, 0 vbr-nrt TX 0 vbr-rt RX, 0 vbr-rt TX 0 ubr RX, 0 ubr TX
Wanneer de interface voor Frame Relay-modus is geconfigureerd, geeft u een opdracht voor show interface DSL uit om Frame Relay-statistieken weer te geven.
DSLAM#show interface idsl2/2 IDSL2/2 is up, line protocol is up Hardware is idsl MTU 1500 bytes, BW 128 Kbit, DLY 0 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY IETF, loopback not set Keepalive set (10 sec) LMI enq sent 0, LMI stat recvd 0, LMI upd recvd 0 LMI enq recvd 8, LMI stat sent 8, LMI upd sent 0, DCE LMI up LMI DLCI 0 LMI type is ANSI Annex D frame relay DCE Broadcast queue 0/64, broadcasts sent/dropped 0/0, interface broadcasts 0 Last input 00:00:03, output 00:00:03, output hang never Last clearing of "show interface" counters 00:01:20 Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 8 packets input, 112 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 8 packets output, 117 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out 0 carrier transitions DSLAM#show dsl interface idsl 2/2 Port Status: Subscriber Name: Circuit ID: IOS admin: UP oper: UP Card status: ITUC-1-8IDSL Last Change: 00 days, 00 hrs, 06 min, 09 sec No. of changes: 64 Loopback: none Firmware version: 961170635 BERT has not been executed on this interface Configured: Profile Name: idslframe Alarms Enabled: NO IDSL profile parameters Bitrate: 128 kbit/sec Encapsulation: frame-relay Frame Relay parameters: UPC intent: pass Bc default: 32768 bytes LMI type: ansi lmi-n392dce: 2 events lmi-n393dce: 2 events lmi-t392dce: 15 seconds Performance Statistics: Physical layer Coding violations : 0 Errored seconds : 0 Severely errored seconds : 0 Physical layer (far end) Coding violations : 0 Errored seconds : 0 Severely errored seconds : 0 HDLC layer Coding violations : 0 Aborts : 0 Aligns : 0 Shorts : 0 Longs : 0 Discards : 0 Alarm Status: NONE DSLAM#show atm vc interface atm-p 2/2 Interface VPI VCI Type X-Interface X-VPI X-VCI Encap Status ATM-P2/2 0 37 PVC ATM0/1 3 300 UP DSLAM#show atm vc interface atm-p 2/2 0 37 Interface: ATM-P2/2, Type: ATM-PSEUDO VPI = 0 VCI = 37 Status: UP Time-since-last-status-change: 00:06:59 Connection-type: PVC Cast-type: point-to-point Packet-discard-option: disabled Usage-Parameter-Control (UPC): pass Number of OAM-configured connections: 2 OAM-configuration: Ais-on OAM-states: OAM-Up OAM-Loopback-Tx-Interval: 5 Cross-connect-interface: ATM0/1, Type: suni_dual Cross-connect-VPI = 3 Cross-connect-VCI = 300 Cross-connect-UPC: pass Cross-connect OAM-configuration: Ais-on Cross-connect OAM-state: OAM-Up OAM-Loopback-Tx-Interval: 5 Rx cells: 0, Tx cells: 0 Rx connection-traffic-table-index: 100 Rx service-category: VBR-NRT (Non-Realtime Variable Bit Rate) Rx pcr-clp01: 106 Rx scr-clp0 : 106 Rx mcr-clp01: none Rx cdvt: none Rx mbs: 50 Tx connection-traffic-table-index: 100 Tx service-category: VBR-NRT (Non-Realtime Variable Bit Rate) Tx pcr-clp01: 106 Tx scr-clp0 : 106 Tx mcr-clp01: none Tx cdvt: none Tx mbs: 50
PPP over Frame Relay wordt niet ondersteund voor Cisco 800-serie voor IDSL.
Als u een Cisco-router wilt gebruiken voor een IDSL-toepassing en de router een Cisco IOS-softwarerelease eerder dan 12.1 draait, moet u het type ISDN-switch configureren. Raadpleeg Cisco Routers configureren voor gebruik met IDSL voor meer informatie.
Als u het type ISDN-switch niet configureren wordt de BRI-interface van de router waarschijnlijk niet opnieuw geactiveerd nadat de IDSL-lijn naar beneden en naar boven gaat. Om dit probleem te voorkomen, moet u het ISDN switch-type basis-in-opdracht uitgeven tijdens de configuratie in de mondiale.
Dit probleem doet zich niet voor als de Cisco-router Cisco IOS-softwarerelease 12.1 of hoger uitvoert.