ステップ 1 |
write erase コマンドを使用するか、デイゼロデバイスで直接、デイゼロ セットアップ ウィザードを開始できます。
|
ステップ 2 |
デバイス管理インターフェイスのセットアップでは、デバイス管理またはサービスポートを設定します。このインターフェイスにより、GUI を使用してデバイスにアクセスするための基本設定が可能になります。これはオプションの設定で、デバイス管理ではなくワイヤレス管理インターフェイスのみを設定できます。
Configure device management interface?[yes]:
(注)
|
Cisco Catalyst 9800-CL Cloud ワイヤレスコントローラには、専用のデバイス管理ポートがありません。したがって、指定された範囲からいずれかのオプションを選択するように求められます。
|
Select interface to be used for device management
1. GigabitEthernet1 [Up]
2. GigabitEthernet2 [Up]
3. GigabitEthernet3 [Up]
Choose the interface to config [1]:
|
ステップ 3 |
デバイス管理 IP は、GUI を使用したデバイスへのアクセスに役立ちます。
Configure static IP address? [yes]:
Enter the interface IP [GigabitEthernet1]: 192.168.1.10
Enter the subnet mask [GigabitEthernet1] [255.0.0.0]: 255.255.255.0
|
ステップ 4 |
(オプション)GUI を使用してデバイスにアクセスするための静的ルートを設定します。
Configure static route? [yes]:
Enter the destination prefix: 192.168.1.0
Enter the destination mask: 255.255.255.0
Enter the forwarding router IP: 192.168.1.1
|
ステップ 5 |
管理ユーザ名とパスワードを入力します。この手順は必須です。
Enter the management username: cisco
Enter the password: ********
Reenter the password: ********
|
ステップ 6 |
デバイス管理インターフェイスを設定していない場合は、ワイヤレス管理を設定します。
Basic management setup is now complete. At this point, it is possible to save the above and
continue wireless setup using the webUI (for this, choose 'no' below)
Would you like to continue with the wireless setup? [yes]: yes
(注)
|
このプロンプトは、17.4 リリースには適用されません。
|
(注)
|
デバイス管理を設定していない場合は、上記バナーが表示される前の手順 7 に進みます。
17.3 リリースでは、少なくとも 1 つのインターフェイス(デバイスまたはワイヤレス管理)を設定した後、ウィザードを終了できます。
このバナーは、17.4 では使用できなくなりました。設定を完了する前にウィザードを終了することはできません。
[Yes ] を選択した場合は、以降の手順に従う必要があります。また、手順 4 で設定した IP を使用してデバイスにアクセスできます。
|
|
ステップ 7 |
ワイヤレス管理インターフェイスの設定は必須です。
Configuring wireless management interface
Select interface to be used for wireless management
1. GigabitEthernet2 [Up]
2. GigabitEthernet3 [Up]
Choose the interface to config [1]:
(注)
|
GigabitEthernet1 がデバイス管理インターフェイスに使用されている場合は、残りの GigabitEthernet インターフェイスが表示されます。
|
|
ステップ 8 |
VLAN ID を入力します。
Enter the vlan ID (1-4094): 112
|
ステップ 9 |
IPv4 または IPv6 アドレスを設定します。
Configure IPv4 address? [yes]:
Enter the interface IP [GigabitEthernet1]: 9.11.112.40
Enter the subnet mask [GigabitEthernet1] [255.0.0.0]: 255.255.255.0
Configure IPv6 address? [yes]: no
|
ステップ 10 |
VLAN DHCP サーバと IP アドレスを設定します。
Do you want to configure a VLAN DHCP Server? [yes]: yes
Enter the VLAN DHCP Server IP [GigabitEthernet1]: 9.11.112.45
|
ステップ 11 |
(オプション)AP クライアントをコントローラに接続するための静的ルートの設定。静的ルートのデフォルトのオプションで、デフォルトルートを設定するように求められます。ただし、別のルートを指定することもできます。
Configure static route? [yes/no]: yes
Enter the destination prefix [0.0.0.0]:
Enter the destination mask [0.0.0.0]:
Enter the forwarding router IP: 9.11.112.1
(注)
|
デバイスを HA RMI として設定し、デフォルトルート(つまり、送信元と宛先を 0.0.0.0 に設定)を設定していない場合、ウィザードからデフォルトルート情報が要求されます。
|
Basic management setup is now complete. At this point, it is possible to save the above and
continue wireless setup using the webUI(for this, choose 'no' below)
Would you like to continue with the wireless setup? [yes]
|
ステップ 12 |
展開モードを選択します。
Choose the deployment mode
1. Standalone
2. Active
3. Standby
Enter your selection [1]:
(注)
|
次のいずれかの展開モードから 1 つ選択できます。
-
スタンドアロン:このモードでは、高可用性のペアリング情報は表示されません。
-
アクティブ:このモードでは、デイゼロ情報をすべて使用してコントローラを設定する必要があります。
-
スタンバイ:このモードでは、[High Availability] 設定に進みます。
|
|
ステップ 13 |
システム名またはホスト名を設定します。
Enter the hostname [WLC]: ciscowlc
(注)
|
この手順は必須です。ホスト名は、RFC 標準に準拠している必要があります。
|
|
ステップ 14 |
(オプション)AP のログインクレデンシャルを設定します。
Configure credentials for management access on Access Points? [yes]:
Enter the management username: cisco
Enter the management password: ****
Reenter the password: ****
Enter the privileged mode access password: ****
Reenter the password: ****
|
ステップ 15 |
国コードを設定します。複数の国コードをカンマで区切って指定できます。
Configure country code for wireless operation in ISO format ? [US]:
|
ステップ 16 |
アクセスポイントがコントローラに接続できるように、日付と NTP を設定します。NTP サーバを使用するか手動で時刻を設定できます。
(注)
|
次の形式で日付を入力します。
MM/DD/YYYY
|
Configure a NTP server now ? [yes]: no
Configure the system time now? [yes]: yes
Enter the date in MM/DD/YYYY format: 10/05/2021
Enter the time in HH:MM:SS format: 10:22:13
|
ステップ 17 |
(オプション)タイムゾーンを設定します。
Configure timezone? [yes]:
Enter name of timezone: ind
Enter hours offset from UTC (-23,23): 5
Enter mins offset from UTC (0,59) [0]: 30
|
ステップ 18 |
(オプション)予想されるクライアント密度を設定します。
Configure Wireless client density? [yes]:
Choose the client density
1. Low
2. Typical
3. High
Enter your selection [2]: 3
|
ステップ 19 |
(オプション)AAA サーバを設定します。
(注)
|
デイゼロ設定では、最大 6 台のサーバを設定できます。
|
Configure AAA servers? [yes]:
Enter the AAA server address: 9.11.112.46
Enter the AAA key: ***
Do you want to add more AAA servers? [yes]:
Enter the AAA server address: 9.11.112.47
Enter the AAA key: ***
Do you want to add more AAA servers? [yes]: no
(注)
|
WPA2 エンタープライズには AAA サーバが必要です。17.4 リリースでは、AAA を 1 か所でのみ設定する必要があります。手順 21 を実行すると、WPA2 エンタープライズは手順 22 で AAA サーバを要求しません。
|
|
ステップ 20 |
(オプション)ワイヤレスネットワークの設定を行い、AP とクライアントを接続するための WLAN 情報を設定します。
Configure Wireless network settings? [yes]:
|
ステップ 21 |
(オプション)クライアントを接続するための SSID を設定します。
Enter the network name or service set identifier (SSID):
Choose the network type
1. Employee
2. Guest
[Employee ] をネットワークタイプとして選択すると、次のオプションが表示されます。
Choose the security type
1. WPA Personal
2. WPA Enterprise
Enter your selection [2]:
[WPA2 Personal ] を選択する場合は、事前共有キー(ASCII)を入力する必要があります。Enter the pre-shared key (ASCII):
[WPA2 Enterprise ] を選択すると、複数の AAA サーバを追加できます。
Enter the AAA server address:
Enter the AAA key:
Enter more AAA server details? [yes]
[Guest ] を選択すると、次のオプションが表示されます。
Please choose the security type:
1. Webauth
2. Authbypass
3. Consent
4. Webconsent
Enter the security type:
|
ステップ 22 |
(オプション)仮想 IP アドレスを設定します。デフォルトの仮想 IP アドレスは 192.0.6.1 です。
Configure virtual IP? [yes]:
Enter the virtual IP [192.0.6.1]:
|
ステップ 23 |
(オプション)RF ネットワーク名を設定します。
Configure RF-Network Name? [yes]:
Enter the RF-Network Name: ciscorf
|
ステップ 24 |
(オプション)自己署名証明書を設定します。
Auto generate certificate for AP join? [yes]:
Choose key size
1.2048
2.3072
3.4096
Enter your selection [1]:
Choose the signature algorithm
1.SHA256
2.SHA384
Enter your selection [1]:
Enter secret key(minimum 8 characters): ********
Self Signed Certificate generation will be done after system boots up.
|
ステップ 25 |
(オプション)高可用性を設定します。
展開モードをアクティブまたはスタンバイに選択する場合は、次の HA ペアリングタイプのいずれかを選択する必要があります。
-
RMI
-
RP-RP
(注)
|
HA ペアリングタイプの詳細については、『Cisco Catalyst 9800 Series Wireless Controller Software Configuration Guide, Cisco IOS XE Bengaluru 17.4.x』の「Part: High Availability (High Availability > Information About Redundancy Management Interface)」を参照してください。
|
High Availability configuration
Please choose the HA pairing type
1. RMI
2. RP-RP
Enter your selection [1]:
RMI+RP を選択した場合は、冗長ポートとして使用するインターフェイスを選択する必要があります。
Select interface to be used as redundancy port
1. GigabitEthernet3 [Up]
Choose the interface to config [1]: 2
Enter the RMI IP for local chassis: 9.11.112.50
Enter the RMI IP for remote chassis: 9.11.112.51
Enter the gateway IP of the last resort: 9.11.112.1
展開モードにスタンバイを選択した場合は、ペアリングを完了するために VLAN ID を指定する必要があります。
Enter the RMI IP for local chassis: 9.11.112.51
Enter the RMI IP for remote chassis: 9.11.112.50
Enter the wireless management VLAN: 112
RP を選択した場合は、冗長ポートとして使用するインターフェイスを選択する必要があります。
Select interface to be used as redundancy port
1. GigabitEthernet3 [Up]
Choose the interface to config [1]: 2
Enter the local IP:
Enter the subnet mask:
Enter the remote IP:
(注)
|
デバイス管理インターフェイスには GigabitEthernet1、ワイヤレス管理インターフェイスには GigabitEthernet2、HA には GigabitEthernet3 を使用することを推奨します。
|
|