The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
This command lists current administrator accounts, except the master administrator account.
show account
Administrator (admin:)
Command privilege level: 4
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, and Cisco Unity Connection.
This command displays the current account locking settings.
show accountlocking
Administrator (admin:)
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, and Cisco Unity Connection.
admin:show accountlocking Account Lockout is enabled Unlock Time : 300 seconds Retry Count : 3 attempts
Command privilege level: 0
Allowed during upgrade: Yes
show cert*
This command displays certificate trust lists.
show cert list { own | trust }
Parameters | Description |
---|---|
own | Specifies owned certificates. |
trust | Specifies trusted certificates. |
Administrator (admin:)
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, and Cisco Unity Connection.
admin:cert list own
This command displays the available selected type certificate files.
show cert list type { own | trust }
Parameters | Description |
---|---|
own |
Specifies owned certificates. |
trust |
Specifies trusted certificates. |
Administrator (admin:)
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, and Cisco Unity Connection.
This command displays certificate contents.
show cert own filename
Parameters | Description |
---|---|
own | Specifies owned certificates. |
filename | Represents the name of the certificate file. |
Administrator (admin:)
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, and Cisco Unity Connection.
This command displays certificate contents.
show cert trust filename
Parameters | Description |
---|---|
trust | Specifies trusted certificates. |
filename | Represents the name of the certificate file. |
Administrator (admin:)
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, and Cisco Unity Connection.
show cli*
This command displays the status of automatic CLI automatic pagination.
show cli pagination
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, and Cisco Unity Connection.
admin:show cli pagination Automatic Pagination : Off.
This command displays the CLI session timeout value, which is the amount of time, in minutes, that can elapse before a CLI session times out and disconnects.
show cli session timeout
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, and Cisco Unity Connection.
show csr*
This command displays Certificate Sign Request contents and certificate trust lists.
show csr list { own | | trust }
Parameters | Description |
---|---|
own |
Shows a list of owned Certificate Sign Requests. |
trust |
Shows a list of trusted Certificate Sign Requests. |
Administrator (admin:)
The certificate name can be obtained by using the show cert list own command.
Command privilege level: 1
Allowed during upgrade:
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
admin: show csr list own
tomcat/tomcat.csr
Vipr-QuetzalCoatl/Vipr-QuetzalCoatl.csr
.....
.....
.....
This command displays the selected own Certificate Sign Request files.
show csr list type own
Parameters | Description |
---|---|
own |
Shows a list of owned Certificate Sign Requests. |
Administrator (admin:)
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays Certificate Sign Request (CSR) contents and certificate trust lists.
show csr own name
Parameters | Description |
---|---|
name |
The name of the CSR file. |
Administrator (admin:)
The certificate name can be obtained by using the show cert list own command.
Command privilege level: 1
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
admin:show csr own tomcat/tomcat.csr
[
[
-----BEGIN CERTIFICATE SIGN REQUEST-----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 command displays Certificate Sign Request (CSR) own certificate files.
show csr own name name of certificate sign request
Parameters | Description |
---|---|
name |
The name of the CSR file. |
name of certificate sign request |
The name of the certificate sign request. |
Administrator (admin:)
The certificate name can be obtained by using the show cert list own command.
Command privilege level: 1
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the contents of the Certificate Trust List (CTL) file on the server. It notifies you if the CTL is invalid.
show ctl
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
show cuc*
This command shows the status of the servers in the cluster.
show cuc cluster status
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection
This command displays a list of the valid configuration group names.
show cuc config groups [page]
Parameters | Description |
---|---|
page |
Causes the output to display one page at a time. Be aware that page is case sensitive. |
Administrator (admin:)
To see a list of the settings for a specified group, run the command show cuc config settings.
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection
admin: show cuc config groups CiscoLicensing ConfigurationAssistant Conversations Directory Groupware LogMgr Messaging : : Telephony
This command displays the settings and values for a specified group of Connection configuration settings.
show cuc config settings group_name page
Parameters | Description |
---|---|
group_name |
Specifies the name of the configuration group whose settings you want to display. To see a list of valid group names, run the command show cuc config groups. Be aware that group names are case sensitive. |
pagepage |
Causes the output to display one page at a time. Be aware that page is case sensitive. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection
admin: show cuc config settings SA SA Setting Value ---------- ----- SessionTimeout 20 Use24HrClockFormat 0
This command checks the tables and indexes of a specified database for inconsistencies.
show cuc dbconsistency [database_name]
Administrator (admin:)
After the command completes, the system saves detailed information in a log file and displays a summary of the results, including the location of the log file. Use the file commands to display the contents of the file.
Caution | Checking database consistency makes a significant impact on system performance. Run this command only when little or no system activity is occurring. After the operation begins, you can not cancel it. Do not restart the server during the operation; the operation must complete successfully before Connection will function properly. |
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection
admin: show cuc dbconsistency unityrptdb Checking consistency of unityrptdb tables. Please wait. Consistency check of unityrptdb tables successful. Validation of unityrptdb indexes successful. Output is in file: cuc/cli/consistency_unityrptdb_070404-123636.txt
This command exports the data from a specified database to a CSV file.
show cuc dbcontents [database_name]
Administrator (admin:)
After the command completes, the location of the CSV file displays. Use the file commands to display the contents of the file.
Caution | Saving the contents of a database to a CSV file affects system performance. Run this command only when little or no system activity is occurring. |
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection
admin: show cuc dbcontents unitydirdb This operation may take a few minutes to complete. Please wait. Output is in file: cuc/cli/contents_unitydirdb_070404-124027.csv
This command exports the SQL statements that are necessary to replicate the schema for a specified database to a file.
show cuc dbschema [database_name]
Administrator (admin:)
After the command completes, the location of the file displays. Use the file commands to display the file.
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection
admin: show cuc dbschema unitydirdb Output is in file: cuc/cli/schema_unitydirdb_061013-115815.sql
This command displays summary information about informix storage space for all Connection databases on the current server.
show cuc dbserver disk [page] [file]
Parameters | Description |
---|---|
[page] |
Causes the output to display one page at a time. Be aware that page is case sensitive. |
[file] |
Saves the output to a file. If you include this option, the summary includes the location of the file. Be aware that file is case sensitive. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection
This command displays summary information about a specified informix database user session.
show cuc dbserver session session_id [page] [file]
Parameters | Description |
---|---|
session_id | Specifies the database user session for which you want to display summary information. To get a list of current sessions, use either the show cuc dbserver sessions list command or the show cuc dbserver user list command. |
[page] | Causes the output to display one page at a time. Be aware that page is case sensitive. |
[file] | Saves the output to a file. If you include this option, the summary includes the location of the file. Be aware that file is case sensitive. |
Administrator (admin:)
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection
This command displays summary information about all the current Informix database user sessions.
show cuc dbserver sessions all [page] [file]
Parameters | Description |
---|---|
[page] | Causes the output to display one page at a time. Be aware that page is case sensitive. |
[file] | Saves the output to a file. If you include this option, the summary includes the location of the file. Be aware that file is case sensitive. |
Administrator (admin:)
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection
This command displays a list of the current Informix database user sessions.
show cuc dbserver sessions list [page]
Parameters | Description |
---|---|
[page] | Causes the output to display one page at a time. Be aware that page is case sensitive. |
Administrator (admin:)
The names of internal database users generally correspond with the names of Connection components. Run this command before you run the show cuc dbserver session command to obtain the required session id.
Results are sorted by session id.
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection
This command displays a list of the active Connection internal database users.
show cuc dbserver user list [page]
Parameters | Description |
---|---|
[page] | Causes the output to display one page at a time. Be aware that page is case sensitive. |
Administrator (admin:)
The names of internal database users generally correspond with the names of Connection components.
Results get sorted first by database and then by user.
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection
This command displays a list of the Connection internal users that are waiting for a resource.
show cuc dbserver user waiting [page]
Parameters | Description |
---|---|
[page] | Causes the output to display one page at a time. Be aware that page is case sensitive. |
Administrator (admin:)
The names of the internal database users generally correspond with the names of Connection components.
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection
This command exports the contents of a specified Connection table to a CSV file.
show cuc dbtable contents { database_name | table_name }
Administrator (admin:)
After the command completes, the location of the CSV file displays. Use the file commands to display the contents of the file.
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection
admin: show cuc dbtable contents unitydirdb tbl_cos Output is in file: cuc/cli/contents_tbl_cos_1013-113910.csv
This command displays a list of the tables in a specified database.
show cuc dbtable list database_name [page]
Parameters | Description |
---|---|
database_name |
|
[page] |
Causes the output to display one page at a time. Be aware that page is case sensitive. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection
admin: show cuc dbtable list unitydirdb tbl_accountlogonpolicy tbl_agency tbl_agencyextensionrange tbl_alias tbl_alternatename tbl_broadcastmessage tbl_broadcastmessagerecipient ... tbl_waveformat
This command displays a description for a specified table and a list of the columns in the table.
show cuc dbtable schema { database_name | table_name } [page]
Parameters | Description | ||
---|---|---|---|
database_name |
|
||
table_name |
|
||
[page] |
Causes the output to display one page at a time. Be aware that page is case sensitive. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection
admin: show cuc dbtable schema unitydirdb tbl_cos A collection of service privileges for subscribers that control access to features and use of the system into classes. Class of Service objects determine which features a subscriber is licensed to use, the maximum length of their greetings and messages, what numbers they are allowed to dial, and what options are available to the subscriber among other things. Columns: displayname movetodeletefolder accessunifiedclient ... accesslivereply
This command saves the results from a specified SQL view in a CSV file.
show cuc dbview contents { database_name | view_name }
Parameters | Description | ||
---|---|---|---|
database_name |
|
||
view_name |
|
Administrator (admin:)
After the command completes, the location of the CSV file displays. Use the file commands to display the contents of the file.
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection
admin: show cuc dbview contents unitydirdb vw_cos_061013-113910.csv
This command displays a list of the views in a specified database.
show cuc dbview list database_name [page]
Parameters | Description |
---|---|
database_name |
|
[page] |
Causes the output to display one page at a time. Be aware that page is case sensitive. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
admin: show cuc dbview list unitydirdb vw_agency vw_agencyextensionrange vw_alias vw_alternatename vw_broadcastmessage vw_broadcastmessagerecipient vw_callaction ... vw_waveformat
This command displays the schema for a specified view.
show cuc dbview schema { database_name | view_name } [page]
Parameters | Description | ||
---|---|---|---|
database_name |
|
||
view_name |
|
||
[page] |
Causes the output to display one page at a time. Be aware that page is case sensitive. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection
admin: show cuc dbview schema unitydirdb vw_cos A simple view for tbl_Cos. Columns: objectid accessfaxmail accesstts callholdavailable callscreenavailable canrecordname ... requiresecuremessages
show cuc jetty ssl status
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection
admin: show cuc jetty ssl status Command completed successfully. SSL notification is DISABLED
This command displays a list of the locales currently installed.
show cuc locales
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection
admin: show cuc locales Installed Locale Package Locale ------------------------- ------ uc-locale-en_GB-6.0.0.0-0 en-GB uc-locale-fr_CA-6.0.0.0-0 fr-CA
This command displays a list of the Sysagent tasks.
show cuc sysagent task list [page]
Parameters | Description |
---|---|
[page] |
Causes the output to display one page at a time. Be aware that page is case sensitive. |
Administrator (admin:)
To run a sysagent task, use the run cuc sysagent task command. If the value of the Is Singleton column is Y for a specified task, the task can only be run on the primary server in a multi-server cluster. If this server is standalone, then all tasks run on this server.
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection
admin: show cuc sysagent task list Task Name Is Singleton ------------------------------ ------------ Data.BroadcastMessagePurge N Umss.CleanDeletedMessagesTask Y Umss.CleanDirectoryStreamFilesTask Y Umss.CleanOrphanAttachmentFilesTask Y ... Data.UpdateDatabaseStats N
This command displays the times at which the specified task started and completed, with the most recent time listed first.
show cuc sysagent task results task_name [page]
Parameters | Description | ||
---|---|---|---|
task_name |
|
||
[page] |
Causes the output to display one page at a time. Be aware that page is case sensitive. |
Administrator (admin:)
To run a Sysagent task, use the run cuc sysagent task command.
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection
admin: show cuc sysagent task results Umss.CleanDeletedMessagesTask Time Started Time Completed ---------------------- -------------------- 2006-10-25 17:31:45.689 2006-10-25 17:31:45.785 2006-10-25 17:16:45.702 2006-10-25 17:16:45.742 2006-10-25 17:01:45.690 2006-10-25 17:01:45.730
This command displays a summary of hardware and software system information for the current Connection server, including the version installed on the active and inactive partitions; whether a cluster is configured; QOS settings; hardware specifications; the amount of used and free disk space on the active, inactive, and common partitions; licensing information; and so on.
show cuc sysinfo
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: No
Applies to: Cisco Unity Connection
admin: show cuc sysinfo Gather Data/Time : Wed Oct 21 09:45:29 PDT 2009 Connection Install Information: Host Name : connection1 Version: Active Version : 8.0.0.98000-210 Inactive Version : 8.0.0.98000-201 High Availability (this server is) : Pri_Single_Server Publisher : connection1.cisco.com - 10.10.10.10 Subscriber(s) : None QOS Settings : Call Signaling DSCP : CS3 Media Signaling DSCP : EF Hardware : HW Platform : 7825I3 Processors : 1 Type : Family: Core 2 CPU Speed : 2130 Memory : 2048 Object Id : 1.3.6.1.4.1.9.1.746 OS Version : UCOS 4.0.0.0-31 ...
This command displays the schema version information for each database.
show cuc tech dbschemaversion [page]
Parameters | Description |
---|---|
[page] |
Causes the output to display one page at a time. Be aware that page is case sensitive. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection
admin: show cuc tech dbschemaversion unitydirdb ========== Schema Version Product Version Date -------------- --------------- ----------------- 1.2.363 2.1 2007-02-13 19:10:50.0
This command runs all the show cuc tech commands in sequence and saves the results in a text file.
show cuc tech dbserver all
Administrator (admin:)
After the command completes, detailed information gets saved in a text file and the location of the text file displays. Use the file commands to display the contents of the file.
Command privilege level: 1
Allowed during upgrade: Yes
admin: show cuc tech dbserver all Output is in file: cuc/cli/dbserverall_061013-111801.txt
This command checks the integrity of the Informix database server storage space structure.
show cuc tech dbserver integrity
Administrator (admin:)
After the command completes, detailed information gets saved in a text file, and a summary of the results displays, including the location of the file. Use the file commands to display the contents of the file.
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection
admin: show cuc tech dbserver integrity Database system catalog tables were successfully validated. Database disk extents were successfully validated. Database reserved pages were successfully validated. Output is in file: cuc/cli/integrity_061013-95853.txt
This command checks for the existence of Informix assertion-failure and shared-memory-dump logs.
show cuc tech dbserver log diagnostic
Administrator (admin:)
If the logs exist, their location displays. Use the file commands to display the contents of the files.
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection only.
admin:show cuc tech dbserver log diagnostic The following Informix logs are available for the UC database server: core/af.3599c core/af.36858
This command displays the end of the Informix message log.
show cuc tech dbserver log message [lines] [ page ]
Parameters | Description |
---|---|
lines |
Specifies the number of lines that display at the end of the Informix message log. If the lines parameter is not included, the last 20 lines of the log are displayed. |
page |
(Optional) Causes the output to display one page at a time. Be aware that page is case sensitive. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection only.
admin:show cuc tech dbserver log message Message Log File: online.ciscounity.log 18:09:01 Fuzzy Checkpoint Completed: duration was 0 seconds, 6 buffers not flushed. 18:09:01 Checkpoint loguniq 57, logpos 0x208418, timestamp: 0x33b807 18:09:01 Maximum server connections 159 18:14:01 Fuzzy Checkpoint Completed: duration was 0 seconds, 6 buffers not flushed. 18:14:01 Checkpoint loguniq 57, logpos 0x20a57c, timestamp: 0x33b9fc
This command saves a detailed status report of the database server instance to a file.
show cuc tech dbserver status
Administrator (admin:)
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection only.
admin:show cuc tech dbserver status Output is in file: cuc/cli/status_061013-95031.txt
This command displays a list of all the diagnostic traces and trace levels that are currently enabled.
show cuc trace levels [ page ]
Parameters | Description |
---|---|
page |
(Optional) Causes the output to display one page at a time. Be aware that page is case sensitive. |
Administrator (admin:)
To enable or disable specified traces and trace levels, use the set cuc trace (Cisco Unity Connection only) command.
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection only.
admin:show cuc trace levels Trace Name Levels ------------------------- -------------- Arbiter - AudioStore 0 AxlAccess - BulkAdministrationTool 0 CCL 10,11 CDE 3,14 CDL 11,13,15,17 :: VirtualQueue -
This command displays the Cisco Unity Connection version that is currently installed on the active and inactive partitions.
show cuc version
Administrator (admin:)
This command always displays the version in the active partition. If the active partition contains an upgrade, the command also shows the version in the inactive partition. The current Engineering Special also displays.
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unity Connection only.
admin:show cuc version Active version: 7.0.1.10000-323 Inactive version: 7.0.0.39700-277
This command displays the date and time on the server.
show date
Administrator (admin:)
admin: show date Sat Jul 17 01:28:57 IST 2010
This command displays disk usage information about specific directories.
show diskusage activelog { activelog | common | inactivelog | install | tftp | tmp } filename filename { directory | sort }
Parameters | Description |
---|---|
filename filename |
Saves the output to a specified file. These files are stored in the platform/cli directory. To view saved files, use the file view activelog command. |
directory |
Displays the directory sizes only. |
sort |
Sorts the output on the basis of file size. File sizes display in 1024-byte blocks. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, and Cisco Unity Connection
show dscp*
This command displays the current DSCP traffic markings on all the ports. It displays the DSCP markings in decimal and hexidecimal. If the value corresponds to a class then it displays the correct class. If the value does not correspond to a class, then it displays N/A.
show dscp all
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: No
Applies to: Cisco Unified Communications Manager and Cisco Unity Connection
This command displays the default factory DSCP settings. These values take effect if the set dscp defaults command is executed.
show dscp defaults
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: No
Applies to: Cisco Unified Communications Manager and Cisco Unity Connection
This command displays the current DSCP traffic markings for a particular DSCP value.
show dscp marking value
Parameters | Description |
---|---|
value | DSCP value. You can enter the name of a well-known DSCP class, or a numeric value in decimal or hexadecimal format. Precede hexadecimal values with 0x or 0X. |
Administrator (admin:)
The valid class names as defined by DSCP are:
Class Selector: values CSO, CS1, CS2, CS3, CS5, CS6 CS7
The class selector (CS) values correspond to IP Precedence values and are fully compatible with IP Precedence.
Expedited Forwarding: value EF
EF PHB is ideally suited for applications such as VoIP that require low bandwidth, guaranteed bandwidth, low delay, and low jitter.
Best Effort: value BE
Also called default PHB, this value essentially specifies that a packet be marked with 0x00, which gets the traditional best-effort service from the network router.
Assured Forwarding: values AF11, AF12, AF13, AF21, AF22, AF23, AF41, AF42, AF43
There are four types of Assured Forwarding classes, each of which has three drop precedence values. These precedence values define the order in which a packet is dropped (if needed) due to network congestion. For example, packets in AF13 class are dropped before packets in the AF12 class.
Command privilege level: 1
Allowed during upgrade: No
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, and Cisco Unity Connection
This command displays the current DSCP traffic markings.
show dscp status { enabled | disabled }
Parameters | Description |
---|---|
enabled | Filters the output to show only DSCP traffic markings that are enabled. If you do not specify a status, this filter is the default option. |
disabled | Filters the output to show only DSCP traffic markings that are disabled. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: No
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, and Cisco Unity Connection
show environment
This command shows the status of the fan sensors.
show environment fans
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command shows the status of the power supply for MCS-7845, MCS-7835, MCS-7825H3/H4, and MCS-7816H3 servers—those with redundant power supply or embedded health hardware.
show tlstrace
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command retrieves the status of the temperature sensors.
show environment temperatures
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command shows the reading and writing speed between the IM and Presence Service node and the external file server. It involves copying a large file onto the mounted directory and then copying it back onto the node. As a result, this command may have a performance impact on the node from which it is run.
show fileserver transferspeed
Administrator (admin:)
Applies to: IM and Presence Service on Cisco Unified Communications Manager.
admin:show fileserver transferspeed WARNING: This command involves copying a large file to and from the mounted directory. It can impact the performance of the system. Do you want to continue? (y/n):y Creating a file to perform the test, please wait... Copying the file onto the mounted file system. Please note the writing speed recorded below. 262144+0 records in 262144+0 records out 1073741824 bytes (1.1 GB) copied, 28.9302 s, 37.1 MB/s Copying the file from the mounted file system. Please note the reading speed recorded below. 262144+0 records in 262144+0 records out 1073741824 bytes (1.1 GB) copied, 67.7504 s, 15.8 MB/s Clean-up finised admin:
This command displays hardware-related information about the platform.
show hardware
Administrator (admin:)
The following information is displayed:
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, and Cisco Unity Connection
show ipsec*
This command displays detailed information about the specified ipsec policy.
show ipsec information { policy_group | policy_name }
Parameters | Description |
---|---|
policy_group | |
policy_name |
Administrator (admin:)
Command privilege level: 1
Allowed during upgrade: yes
Applies to: IM and Presence service on Cisco Unified Communications Manager
admin:show ipsec information test test1 PolicyGroup : test PolicyName : test1 Type : transport Source Address : 10.94.171.3 Source Type : ip Destination Address : 10.94.1.2 Destination Type : ip Protocol : tcp Source Port : Any Destination Port : Any Remote Port : Any Authentication Method : psk Destination Certificate : null PSK : cisco Phase 1 Life Time : 3600 Encryption Algorithm : des Hash Algorithm : sha1 Phase 1 DH Value : null Phase 2 Life Time : 3600 ESP : null_enc AH : hmac_sha1 Phase 2 DH Value : null Peer Type : null Status : disabled Source Certificate : null
This command displays all the ipsec policy group on the node.
show ipsec policy_group
Administrator (admin:)
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager and Cisco Unity Connection
This command displays the list of ipsec policy names that exist in the specified policy group.
show ipsec policy_name policy_group
Parameters | Description |
---|---|
policy_group | Specifies the policy group name. |
Administrator (admin:)
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager and Cisco Unity Connection
show ipsec status
Administrator (admin:)
Command privilege level:
Allowed during upgrade:
Applies to: IM and Presence service on Cisco Unified Communications Manager
This command displays the ITL file contents or prints an error message if the ITL file is invalid.
show itl
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, and Cisco Unity Connection
show logins*
This command lists recent logins to the server
show login [number]
Parameters | Description |
---|---|
number | Specifies the number of the most recent logins to display. The default is 20. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager and Cisco Unity Connection
This command shows the previous successful logins.
show logins successful [ last n ]
Parameters | Description |
---|---|
last n |
(Optional) Represents the last number of logins. By default, the value of this variable is 20. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
Use this command to list recent unsuccessful login attempts to the following web applications:
show logins unsuccessful [number]
Parameters | Description |
---|---|
number |
Specifies the number of most recent logins to display. The default is 20. |
Administrator (admin)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to Cisco Unified Communications Manager and IM and Presence Service
This command shows the login Grace Timeout.
show Login Grace Timeout
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command captures information on current media stream connections.
show media streams [options]
Parameters | Description | ||
---|---|---|---|
options |
|
Administrator (admin:)
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager and Cisco Unity Connection
admin: show media streams info buffers Resulting file /platform/log/mediainfo.txt contains: Time: 2008.03.04 11:01:42 I/F Ver=5, #Apps: Free= 7, Alloc= 4, #Conf: Free= 12, #Streams: Free= 40 Buffer Size = 652, Allocated Buffers= 1, Free Buffers = 5147 Buffer Size = 8192, Allocated Buffers= 0, Free Buffers = 450 App ID= 332, Cfg=CFB, Dead App Timer=86400, Active=Yes, Streams: Available= 92 Active= 4 Conf ID = 16777225, Type = Two No Sum, Streams: Tx = 2, Rx = 2, Active = Yes Rx Stream: PktCnt= 5979, PID=16777653, PktSz=20ms, Payld=uLaw, IP=10.89.80.178:24652, MCast=N, Mute=N, UsrMd=N, Actv=Y, QdPkts=2, PktOR=0, DtmfPL=0 DiscTimeSlice= 0 DiscPkts= 0 10:59:42 Buffer Size = 652, Used Buffers = 1 Buffer Size = 8192, Used Buffers = 0 Rx Stream: PktCnt= 6179, PID=16777651, PktSz=20ms, PayId=uLaw, IP=10.89.80.178:24650, MCast=N, Mute=N, UsrMd=N, Actv=Y, QdPkts=0, PktOR=0, DtmfPL=0 DiscTimeSlice= 0 DiscPkts= 0 10:59:38 Buffer Size = 652, Used Buffers = 0 Buffer Size = 8192, Used Buffers = 0 Tx Stream: PktCnt= 5988, PID=16777653, PktSz=20ms, Payld=uLaw, IP=10.13.5.189:29450 (24652), MCast=N, Mute=N, UsrMd=N, Actv=Y, DtmfPL=0, DtmfQ=0 10:59:42 Buffer Size = 652, Used Buffers = 0 Buffer Size = 8192, Used Buffers = 0 Tx Stream: PktCnt= 6193, PID=16777651, PktSz=20ms, Payld=uLaw, IP=10.13.5.182:28516(24650), MCast=N, Mute=N, UsrMd=N, Actv=Y, DtmfPL=0, DtmfQ=0 10:59:42 Buffer Size = 652, Used Buffers = 0 Buffer Size = 8192, Used Buffers = 0 App ID= 331, Cfg=ANN, Dead App Timer=86400, Active=Yes, Streams: Available= 96 Active= 0 App ID= 330, Cfg=MOH, Dead App Timer=86400, Active=Yes, Streams: Available= 658 Active= 0 App ID= 329, Cfg=MTP, Dead App Timer=86400, Active=Yes, Streams: Available= 96 Active= 0
This command displays information about the onboard memory.
show memory { count | modules | size }
Parameters | Description |
---|---|
count |
Displays the number of memory modules on the system. |
modules |
Displays detailed information about all the memory modules. |
size |
Displays the total amount of physical memory. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, and Cisco Unity Connection
This command displays information about the current account.
show myself
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, and Cisco Unity Connection
show network*
This command shows network information for listening and nonlistening sockets.
show network all [detail] [page] [ search srchtext ]
Parameters | Description |
---|---|
detail | Shows additional information. |
page | Displays information one page at a time. |
search srchtext | Searches for srchtext in the output. |
Administrator (admin:)
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command lists nodes in the network cluster and also shows the remaining timer value when you enable Dynamic Cluster Configuration.
show network cluster
Administrator (admin:)
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command shows DHCP status information.
show network dhcp eth0
Administrator (admin:)
The eth0 parameter displays Ethernet port 0 settings, including DHCP configurations and options.
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command shows network information for ethernet 0.
show network eth0 [detail] [ search srchtxt ]
Parameters | Description |
---|---|
detail | Shows additional information. |
search srchtxt | Searches for srchtxt in the output. |
Administrator (admin:)
The eth0 parameter displays Ethernet port 0 settings
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command shows Network Fault Tolerance information.
show network failover [detail] [page]
Parameters | Description |
---|---|
detail | Shows additional information. |
page | Shows information one page at a time. |
Administrator (admin:)
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command shows ip_conntrack usage information.
show network ip_conntrack
Administrator (admin:)
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command shows the list of ports that have been requested to be opened or translated in the firewall.
show network ipprefs { all | enabled | public }
Parameters | Description |
---|---|
all |
Shows all incoming ports that may be used on the product. |
enabled |
Shows all incoming ports that are currently opened. |
public |
Shows all incoming ports that are currently opened for a remote client. |
Administrator (admin:)
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
admin:show network ipprefs public Application IPProtocol PortValue HashLimit (max:rate) H-Status ConnLimit C-Status Type XlatedPort Status Description ----------- --------- --------- -------------------- -------- --------- -------- ---- ---------- ------ ------------ sshd tcp 22 1500:25/second enabled - disabled public - enabled sftp and ssh tomcat tcp 443 4000:50/second disabled 300 enabled public 8443 enabled secure web tomcat tcp 80 4000:50/second disabled 300 enabled public 8080
This command shows IPv6 network routes and network settings.
show network ipv6 { route | settings }
Parameters | Description |
---|---|
route | Shows all IPv6 routes. |
settings | Shows all IPv6 network settings. |
Administrator (admin:)
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, Cisco Unity Connection
This command shows max_ip_conntrack information.
show network max_ip_conntrack
Administrator (admin:)
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the security option that is configured in the /etc/config file.
show network ntp option
Administrator (admin:)
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command shows network routing information.
show network route [detail] [ search srchtext ]
Parameters | Description |
---|---|
detail | Shows additional information. |
search srchtext | Searches for the srchtext in the output. |
Administrator (admin:)
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command shows active internet connections.
show network status [detail] [listen] [process] [all] [nodns] [ search stext ]
Parameters | Description |
---|---|
detail | Shows additional information. |
listen | Shows only listening sockets. |
process | Shows the process ID and name of the program to which each socket belongs. |
all | Shows both listening and nonlistening sockets. |
nodns | Shows numerical addresses without any DNS information. |
search stext | Searches for the stext in the output. |
Administrator (admin:)
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
admin: show network status
This command displays name service cache general attributes.
show network name - service attributes
Administrator (admin:)
Command privilege level: 1
Allowed during upgrade: No
Example:
admin:show network name-service hosts attributes enable-cache yes positive-time-to-live 3600 negative-time-to-live 20 Successful
This command displays name service cache statistics.
show network name-services [host] [services] cache-stats
Parameters | Description |
---|---|
hosts |
host services cache. |
services |
services service cache. |
Administrator (admin:)
Command privilege level: 1
Allowed during upgrade: No
Example:
admin:show network name-service hosts cache-stats yes cache is enabled no cache is persistent yes cache is shared 211 suggested size 216064 total data pool size 272 used data pool size 3600 seconds time to live for positive entries 20 seconds time to live for negative entries 0 cache hits on positive entries 0 cache hits on negative entries 2 cache misses on positive entries 0 cache misses on negative entries 0% cache hit rate 2 current number of cached values 2 maximum number of cached values 0 maximum chain length searched 0 number of delays on rdlock 0 number of delays on wrlock 0 memory allocations failed yes check /etc/hosts for changes Successful
This command displays name service cache attributes.
show networkname - service{hosts|services} attributes
Parameters | Description |
---|---|
hosts |
hosts services cache. |
services |
services service cache. |
Administrator (admin:)
Command privilege level: 1
Allowed during upgrade: No
Example:
admin:show network name-service hosts attributes enable-cache yes positive-time-to-live 3600 negative-time-to-live 20 suggested-size 211 persistent no max-db-size 33554432 Successful
show open*
show open files*
This command shows all open files on the system.
show open files all
Administrator (admin:)
Command privilege level: 0
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
The command shows open files that belong to a specified process.
show open files process processID
Parameters | Description |
---|---|
processID |
Specifies a process. |
Administrator (admin:)
Command privilege level: 0
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command shows open files that match the specified regular expression.
show open files regexp reg_exp
Parameters | Description |
---|---|
reg_exp |
Specifies a regular expression. |
Administrator (admin:)
Command privilege level: 0
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
show open ports*
This command shows all open ports on the system.
show open ports all
Administrator (admin:)
Command privilege level: 0
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays open ports the belong to a specified process.
show open ports process processID
Parameters | Description |
---|---|
processID |
Specifies a process. |
Administrator (admin:)
Command privilege level: 0
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command shows open ports that match the specified regular expression.
show open ports regexp reg_exp
Parameters | Description |
---|---|
reg_exp |
Specifies a regular expression. |
Administrator (admin:)
Command privilege level: 0
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the name and version for installed packages.
show packages { active | inactive } name [page]
Parameters | Description |
---|---|
active | Specifies active packages. |
inactive | Specifies inactive packages. |
name | Specifies the package name. To display all active or inactive packages, use the wildcard character, *. |
page | Shows the output one page at a time |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
show password*
This command shows information about the configured password.
show password { age | history | inactivity }
Parameters | Description |
---|---|
age | Shows information about the configured password age parameters |
history | Shows the number of passwords that the history maintains for OS administration accounts. |
inactivity | Shows the status of the password inactivity for OS accounts. Password inactivity is the number of days of inactivity after a password has expired before the account is disabled. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command shows whether a user is forced to change passwords after the user signs in to the system the next time.
show password change-at-login userid
Parameters | Description |
---|---|
userid |
Specifies the user account that you want to show. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: No
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the status of the password complexity rules—whether they are disabled or enabled. If the password complexity rules are enabled, this command displays the shows their current configuration.
show password complexity character
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the minimum length of passwords that need to be used for Cisco OS administrator accounts. The default minimum length of a password is six characters.
show password complexity length
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
show password expiry*
This command shows the configured password expiration parameters.
show password expiry { maximum-age | minimum-age }
Parameters | Description |
---|---|
maximum-age | Shows the maximum number of days for set password expiry. |
minimum-age | Shows the minimum number of days for set password expiry. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command shows the configured password expiration parameters for the specified user.
show password expiry user { maximum-age | minimum-age } userid
Parameters | Description |
---|---|
maximum-age | Shows the maximum number of days for set password expiry. |
minimum-age | Shows the minimum number of days for set password expiry. |
userid | Specifies the user account that you want to show. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command shows the password maximum age and password minimum age for each CLI user in the system.
show password expiry user
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
show perf*
This command displays information about the specified perfmon counter.
show perf counterhelp class-name counter-name
Parameters | Description |
---|---|
class-name | Represents the class name that contains the counter. |
counter-name | Represents the counter that you want to view. |
Administrator (admin:)
If the class name or counter name contains white spaces, enclose the name in double quotation marks.
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command lists the categories in the perfmon system.
show perf list categories
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command lists perfmon classes (objects).
show perf list classes [ cat category ] [ detail ]
Parameters | Description |
---|---|
cat category | Displays perfmon classes for the specified category. |
detail | Displays detailed information. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command lists perfmon counters for the specified perfmon class.
show perf list counters class-name [ detail ]
Parameters | Description |
---|---|
class-name | Represents the class name that contains the counter. |
detail | Displays detailed information. |
Administrator (admin:)
If the class name contains white spaces, enclose the name in double quotation marks.
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command lists the perfmon instances for the specified perfmon class.
show perf list instances class-name [ detail ]
Parameters | Description |
---|---|
class-name | Represents the class name that contains the counter. |
detail | Displays detailed information. |
Administrator (admin:)
If the class name contains white spaces, enclose the name in double quotation marks.
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command queries a perfmon class and displays all the instances and counter values of each instance.
show perf query class class-name [ ,class-name... ]
Parameters | Description |
---|---|
class-name | Represents the class name that contains the counter. |
Administrator (admin:)
If the class name contains white spaces, enclose the name in double quotation marks.
You can specify a maximum of five classes for each command.
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command queries the specified counter or counters and displays the counter value of all instances.
show perf query counter class-name counter-name [ ,counter-name... ]
Parameters | Description |
---|---|
class-name | Represents the class name that contains the counter. |
counter-name | Represents the counter that you want to view. |
Administrator (admin:)
If the class name or counter name contains white spaces, enclose the name in double quotation marks.
You can specify a maximum of five counters for each command.
Note | The output that this command returns depends on the number of endpoints that is configured in the Route Groups in Cisco Unified Communications Manager. |
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command queries the specified instance and displays all its counter values.
show perf query instance class-name instance-name [ ,instance-name... ]
Parameters | Description |
---|---|
class-name | Represents the class name that contains the counter. |
instance-name | Specifies the perfmon instance to view. |
Administrator (admin:)
If the class name contains white spaces, enclose the name in double quotation marks.
You can specify a maximum of five instances for each command.
This command does not apply to singleton perfmon classes.
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command queries a specified perfmon path.
show perf query path path-spec [ ,path-spec... ]
Parameters | Description |
---|---|
path-spec | Specifies a perfmon path. |
Administrator (admin:)
For an instance-based perfmon class, you must specify path-spec as follows: class-name(instance-name)\counter-name
For a noninstance-based perfmon class (a singleton), you must specify path-spec as follows: class-name\counter-name
You can specify a maximum of five paths for each command.
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
admin: show perf query path "Cisco Phones(phone-0)\CallsAttempted","Cisco Unified Communications Manager\T1ChannelsActive"
show process*
This command displays a list of all the processes and critical information about each process and visually indicates the child-parent relationships between the processes.
show process list [ file filename ] [ detail ]
Parameters | Description |
---|---|
file |
Outputs the results to the file that is specified by the filename variable. |
filename |
Specifies the filename. |
detail |
Displays detailed output. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the current load on the system.
show process load [ cont ] [ clear ] [ noidle ] [ num number ] [ thread ] [ cpu | | memory | | time ] [ page ]
Parameters | Description |
---|---|
cont |
Repeats the command continuously. |
clear |
Clears the screen before displaying output. |
noidle |
Ignores the idle or zombie processes. |
num number |
Displays the number of processes that are specified by number. The default number of processes equals 10. Set number to all to display all processes. |
thread |
Displays threads. |
cpu |
Sorts output by CPU usage. This is the default sorting. |
memory |
Sorts output by memory usage. |
time |
Sorts output by time usage. |
page |
Displays the output in pages. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the details of processes that share the same name and indicates their parent-child relationship.
show process name process [ file filename ]
Parameters | Description |
---|---|
process |
Specifies the name of a process. |
file filename |
Outputs the results to the file that is specified by filename. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
The command shows the details of processes that share the same name. This commands displays parent-child relationship.
show process name process name [ file vm detail cont ]
Parameters | Description |
---|---|
process name |
Specifies the name of a process. |
file |
(Optional) Shows the file name where the output is to be received. |
vm |
(Optional) Shows the virtual memory of the process. |
detail |
(Optional) Shows the details, such as page fault, virtual memory, and start time of the process. |
cont |
(Optional) Repeats the command continuously. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command lists the open file descriptors for a comma separated list of process IDs.
show process open file
Parameters | Description |
---|---|
file |
(Optional) Shows the file name where the output is to be received. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command lists the open file descriptors for a comma-separated list of process IDs.
show process open-fd process-id [ ,process-id2 ]
Parameters | Description |
---|---|
process-id |
Specifies the process-id. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command shows a specific process number or command name.
show process pid pid [ file filename ]
Parameters | Description |
---|---|
pid |
Specifies the process ID number of a process. |
file filename |
Outputs the results to the file that is specified by filename. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command searches for the pattern that the regular expression regexp specifies in the output of the operating system-specific process listing.
show process search regexp [ file filename ]
Parameters | Description |
---|---|
regexp |
Represents a regular expression. |
file filename |
Outputs the results to the file that is specified by filename. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command retrieves details of processes that share the user name and displays parent-child relationship.
show process user username [ file detail detail detail cont ]
Parameters | Description |
---|---|
username |
Specifies the username. |
file filename |
Outputs the results to the file that is specified by filename. |
vm |
(Optional) Shows the virtual memory of the process. |
detail |
(Optional) Shows the details, such as page fault, virtual memory, and start time of the process. |
cont |
(Optional) Repeats the command continuously. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays a list of the most CPU-intensive processes.
show process using-most cpu [ number ] [ file filename ]
Parameters | Description |
---|---|
number |
Specifies the number of processes to display. The default specifies 5. |
file filename |
Outputs the results to the file that is specified by filename. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays a list of the most memory-intensive processes.
show process using-most memory [ number ] [ file filename ]
Parameters | Description |
---|---|
number |
Specifies the number of processes to display. The default specifies 5. |
file filename |
Outputs the results to the file that is specified by filename. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the contents of the registry.
show registry system component [ name ] [ page ]
Parameters | Description |
---|---|
system |
Represents the registry system name. |
component |
Represents the registry component name. |
name |
Represents the name of the parameter to show. |
page |
Displays one page at a time. |
Administrator (admin:)
If the name is “page,” and you want to display the output one page at a time, use the command show registry system component name page page
To show all components in a system, enter the wildcard character * in the command: show registry system *
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
admin:show registry cm dbl/sdi system = cm component = dbl/sdi tracelevel=127 enable=1 outputdebugstringflag=0 numminutes=1440 tracefile=/var/log/active/cm/trace/dbl/sdi/dbl.log numfiles=250 numlines=10000
show risdb*
This command displays the tables that are supported in the Realtime Information Service (RIS) database.
show risdb list [ file filename ]
Parameters | Description |
---|---|
file filename | Outputs the information to a file. |
Administrator (admin:)
The file option saves the information to platform/cli/filename.txt. Ensure that the filename does not contain the "." character.
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
admin: show risdb list
This command displays the contents of the specified RIS tables.
show risdb query table1 table2 table3 ... [ file filename ]
Parameters | Description |
---|---|
table1 | Specifies the name of a table. |
file filename | Outputs the information to a file. |
Administrator (admin:)
The file option saves the information to platform/cli/filename.txt. Ensure that the filename does not contain the "." character.
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the trace level that is currently configured.
show samltrace level
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Unified Communications Manager, IM and Presence Service on Unified Communications Manager, Cisco Unity Connection.
This command shows the upper limit for concurrent SSH sessions.
show session maxlimit
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the name of the SMTP host.
show snmp
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the IO statistics.
show stats io [ kilo ] [ detail ] [ page ] [ file filename ]
Parameters | Description |
---|---|
kilo | Displays statistics in kilobytes. |
detail | Displays detailed statistics on every available device on the system and overrides the kilo option. |
page | Displays one page at a time. |
file filename | Outputs the information to a file specified by filename |
Administrator (admin:)
The file option saves the information to platform/cli/filename.txt. Ensure that the filename does not contain the "." character.
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays basic platform status.
show status
Administrator (admin:)
This command displays the following basic platform status:
Command privilege level: 0
Allowed during upgrade: No
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
show tech*
This command displays the active queries to the database taken at one minute intervals as far back as the logs allow.
show tech activesql
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the combined output of all show tech commands.
show tech all [ page ] [ file filename ]
Parameters | Description |
---|---|
page |
Displays one page at a time. |
file filename |
Outputs the information to a file. |
Administrator (admin:)
The file option saves the information to platform/cli/filename.txt. Ensure that the file name does not contain the "." character
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays information about all services that can run on the system.
show tech ccm_service
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command shows information about the database.
show tech database { dump | sessions }
Parameters | Description |
---|---|
dump |
Creates a CSV file of the entire database. |
sessions |
Redirects the session and SQL information of the present session IDs to a file. |
Administrator (admin:)
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays information (from the database log files) about the error code that is specified.
show tech dberrcode errorcode
Parameters | Description |
---|---|
errorcode |
Specifies the error code as a positive integer. |
Administrator (admin:)
If the error code is a negative number, enter it without the minus sign (-).
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the currently running high cost tasks and high CPU-intensive tasks.
show tech dbhighcputasks
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the database integrity.
show tech dbintegrity
Administrator (admin:)
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the database schema in a CSV file.
show tech dbschema [ car | cm ]
Parameters | Description |
---|---|
car |
Represents the car database. |
cm |
Represents the cm database. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the database in use.
show tech dbinuse [ car | cm ]
Parameters | Description |
---|---|
car |
Represents the car database. |
cm |
Represents the cm database. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the state of the database.
show tech dbstateinfo [ car | cm ]
Parameters | Description |
---|---|
car |
Represents the car database. |
cm |
Represents the cm database. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the device defaults table.
show tech devdefaults
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command provides detailed information for customer support in the case of a standard upgrade condition.
show tech dumpCSVandXML
Administrator (admin:)
You can get this file in the following ways:
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the gateway table from the database.
show tech gateway
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the locale information for devices, device pools, and end users.
show tech locales
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays all network tech information.
show tech network all [ page ] [ search text ] [ file filename ]
Parameters | Description |
---|---|
page |
Displays one page at a time. |
search text |
Searches the output for the string that text specifies. Be aware that the search is case insensitive. |
file filename |
Outputs the information to a file. |
Administrator (admin:)
The file option saves the information to platform/cli/filename.txt. Ensure that the file name does not contain the "." character
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays information about hosts configuration.
show tech network hosts [ page ] [ search text ] [ file filename ]
Parameters | Description |
---|---|
page | Displays one page at a time. |
search text | Searches the output for the string that text specifies. Be aware that the search is case insensitive. |
file filename | Outputs the information to a file. |
Administrator (admin:)
The file option saves the information to platform/cli/filename.txt. Ensure that the file name does not contain the "." character
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays information about the network interfaces.
show tech network interfaces [ page ] [ search text ] [ file filename ]
Parameters | Description |
---|---|
page |
Displays one page at a time. |
search text |
Searches the output for the string that text specifies. Be aware that the search is case insensitive. |
file filename |
Outputs the information to a file. |
Administrator (admin:)
The file option saves the information to platform/cli/filename.txt. Ensure that the file name does not contain the "." character
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays information about hostname resolution.
show tech network resolv [ page ] [ search text ] [ file filename ]
Parameters | Description |
---|---|
page | Displays one page at a time. |
search text | Searches the output for the string that text specifies. Be aware that the search is case insensitive. |
file filename | Outputs the information to a file. |
Administrator (admin:)
The file option saves the information to platform/cli/filename.txt. Ensure that the file name does not contain the "." character
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays information about network routes.
show tech network routes [ page ] [ search text ] [ file filename ]
Parameters | Description |
---|---|
page | Displays one page at a time. |
search text | Searches the output for the string that text specifies. Be aware that the search is case insensitive. |
file filename | Outputs the information to a file. |
Administrator (admin:)
The file option saves the information to platform/cli/filename.txt. Ensure that the file name does not contain the "." character
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the list of open sockets.
show tech network sockets { numeric }
Parameters | Description |
---|---|
numeric |
Displays the numerical addresses of the ports instead of determining symbolic hosts. This parameter is equivalent to running the Linux shell numeric [-n] command. |
Administrator (admin:)
Command privilege level: 1
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the database change notify monitor.
show tech notify [search pattern_to_match]
Parameters | Description |
---|---|
search pattern_to_match |
Represents the string that needs to be searched in the command output. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the database parameters.
show tech params { all | | enterprise | | service }
Parameters | Description |
---|---|
all |
Displays all the database parameters. |
enterprise |
Displays the database enterprise parameters. |
service |
Displays the database service parameters. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays database settings.
show tech prefs
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the CAR or CM procedures that are in use for the database.
show tech procedures { car | | cm }
Parameters | Description |
---|---|
car |
Specifies the CAR procedures. |
cm |
Specifies the CM procedures. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the replication timeout.
show tech repltimeout
Administrator (admin:)
When you increase the replication timeout, ensure that as many servers as possible in a large system are included in the first round of replication setup. If you have the maximum number of servers and devices, set the replication timeout to the maximum value. Be aware that this delays the initial set up of replication to give all servers time to get ready for setup.
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the route patterns that are configured for the system.
show tech routepatterns
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the route plans that are configured for the system.
show tech routeplan
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays CPU usage information at the time the command is run.
show tech runtime { all | cpu | disk | env | memory } page file filename
Parameters | Description | ||
---|---|---|---|
all |
Displays all runtime information. |
||
cpu |
Displays CPU usage information at the time the command is run. |
||
disk |
Displays system disk usage information. |
||
env |
Displays environment variables. |
||
memory |
Displays memory usage information. |
||
page |
Displays one page at a time. |
||
file filename |
Outputs the information to a specified file.
|
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, and Cisco Unity Connection
This command prints the history of SQL statements executed.
show tech sqlhistory
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the name of all tables in the sysmaster database.
show tech systables
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays all the system information.
show tech system { all | bus | hardware | host | kernel modules | software | tools } page file filename
Parameters | Description |
---|---|
all |
Displays all the system information. |
bus |
Displays information about the data buses on the server. |
hardware |
Displays information about the server hardware. |
host |
Displays information about the server. |
kernel modules |
Lists the installed kernel modules. |
software |
Displays information about the installed software versions. |
tools |
Displays information about the software tools on the server. |
page |
Displays one page at a time. |
file filename |
Outputs the information to a file. This option saves the information to platform/cli/<filename>.txt. Ensure that the file name does not contain the "." character. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the contents of the specified database table.
show tech table table_name [page]
Parameters | Description |
---|---|
table_name |
Represents the name of the table to display. |
page |
Displays the output one page at a time. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays table names and the triggers that are associated with those tables.
show tech triggers
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the version of the installed components.
show tech version [page]
Parameters | Description |
---|---|
page |
Displays one page at a time. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
show timezone
This command displays the current timezone settings.
show timezone config
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the available timezones.
show timezone list [ page ]
Parameters | Description |
---|---|
page | Displays the output one page at a time. |
Administrator (admin:)
Although the list of available time zones includes Factory, Cisco Unified Communications Manager does not support the Factory timezone.
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command shows the status of TLS trace for a service.
show tlstrace [ service ]
Parameters | Description |
---|---|
service |
Represents the TLS tracing status of a service. It is a mandatory parameter. |
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command shows the TLS session resumption timeout.
show tlsresumptiontimeout
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays trace information for a particular task.
show trace [ task_name ]
Parameters | Description |
---|---|
task_name | Represents the name of the task for which you want to display the trace information. |
Administrator (admin:)
If you do not enter a parameter, the command returns a list of available tasks.
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
admin: show trace cdps
This command shows the current status of the USB-connected APC smart-UPS device and starts the monitoring service if this service is not already started.
show ups status
Administrator (admin:)
This command provides full status only for 7835-H2 and 7825-H2 servers.
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
show version*
This command displays the software version on the active partition.
show version active
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the software version on the inactive partition
show version inactive
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the contents of the current web-security certificate.
show web-security
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command displays the webapp session timeout value, which is the amount of time, in minutes, that can elapse before a web application times out and logs off the user.
show webapp session timeout
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
This command retrieves the current working directory for activelog, inactivelog, install, and TFTP.
show workingdir
Administrator (admin:)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to: Cisco Unified Communications Manager, IM and Presence service on Cisco Unified Communications Manager, Cisco Unity Connection
Use this command to list recent unsuccessful login attempts to the following web applications:
show logins unsuccessful [number]
Parameters | Description |
---|---|
number |
Specifies the number of most recent logins to display. The default is 20. |
Administrator (admin)
Command privilege level: 0
Allowed during upgrade: Yes
Applies to Cisco Unified Communications Manager and IM and Presence Service