Release Notes for SPA100 Series Analog Telephone Adapters Firmware Version 1.3.3
Firmware Released: May 2013; Document Revised: July 2015
These Release Notes provide information about SPA100 Series Analog Telephone Adapters firmware version 1.3.3.
As with any firmware release, read these release notes before upgrading the firmware. Cisco also recommends backing up the configuration before any firmware upgrade.
Changes in Firmware Version 1.3.3
For the Cisco SPA100 series, the following changes are made in firmware version 1.3.3:
Improvement in reboot time for SPA122 (increase in RC provisioning speed.)
User is able to add configurable prefix to syslog (For example: $PN, $MA, etc.)
SPA reboots upon every resync: This feature reduces unnecessary reboot when the same parameter appears in multiple profile files.
Use SIP Notify event: When the parameter, <Provisioning Enable> is set to "no", SPA can resync to turn on provisioning remotely.
Logs over TLS.
Supports SSL email.
Enhancement to include MAC address of the device in syslog messages.
Reports memory (low) availability via syslog.
FW upgrade using HTTP 302 redirection.
Caller ID updated while creating a conference.
Call Hold reminder when the caller makes the second call, while the first call is on hold.
ATA memory usage displayed on the GUI.
Hardware and Firmware Compatibility Matrix
(3 types of devices)
1.3.5p(XU), 1.3.5p, 1.3.2p
1.3.5(XU), 1.3.5, 1.3.4, 1.3.3, 1.3.2n
1.3.2(XU), 1.3.2 or earlier
(128MB Flash + New Si3217x-B SLIC)
CCQ18400001 to CCQ1841033K
CCQ1834031U to CCQ1834037D
CCQ1847066I to CCQ184707YA
CCQ184902ED to CCQ184904UL
CCQ184904UM to CCQ184904Y3
CCQ184904Y4 to CCQ184904Y5
(128MB Flash + Old Si3217x-B SLIC)
CCQ175106J3 to CCQ175106OM
CCQ181607OO to CCQ181607U7
CCQ18240E34 to CCQ18400000
CCQ1841033L to CCQ18500D9K
CCQ174602V3 to CCQ1746030M
CCQ181502B7 to CCQ181502GQ
CCQ182002W3 to CCQ1834031T
CCQ1834037E to CCQ18470660
CCQ184707YB to CCQ184902EC
CCQ184904UM to CCQ184904UL
CCQ184904Y4 to CCQ184904Y3
CCQ184904Y6 to CCQ185001YH
(32MB Flash + Old Si3217x-B SLIC)
SPA112: Before CCQ182002W2
SPA122: Before CCQ181805KR
Note Do not upgrade any device to an unsupported firmware version as detailed in the Hardware and Firmware Compatibility Matrix table.
Note 1.3.2p is identical to 1.3.2 and additionally supports 128MB flash and new SLIC. 1.3.2n is based on 1.3.2; both have the same feature set, except that 1.3.2n supports 128MB flash while 1.3.2 does not. 1.3.5p is based on 1.3.5; both have the same feature set, except that 1.3.5p supports new SLIC while 1.3.5 does not. 1.3.5p(XU), 1.3.5(XU), 1.3.2(XU): SRTP functionality has been removed, and it cannot be configured or provisioned in firmware versions that are designated with XU in the filename.
Note New devices have a label that reads S/W: Must use 1.3.5(004p) or later.
Resync error retry delay is applicable even after profile rule is modified.
Reset button factory reset is not always effective.
Web Access Admin Access is disabled from web-GUI but not from config.
When profile_rule and profile_rule_b are both changed, the SPA100/200 fails to load first profile rule.
T38 fax fails with model "Cannon MX850", but successful with other models like Brother FAX 8360P, Xerox WorkCentre Pro 575, Panasonic UF-9000, and HP Officejet 7110.
The volume is 2dbm lower than the SPA2102 with default settings.
FQDN is required in the profile rule after setting Restricted Access Domains.
The SPA100/200 series does not support RFC2543 Call Hold.
Note Re-INVITE message always has the device ip address in its SDP and not 0.0.0.0
Upgrade the Firmware
Follow these instructions to upgrade the phone adapter.
Step 2 Launch a web browser, and enter the LAN IP addresses of the phone adapter.
Step 3 Log in to the Configuration Utility.
Step 4 Click Administration in the menu bar, and then click Firmware Upgrade in the navigation tree.
Step 5 Click Browse and select the location of the upgrade file that you downloaded.
Step 6 Click the Upgrade button to upgrade the firmware.
Note Upgrading the firmware may take several minutes. Until the process is complete, DO NOT turn off the power, press the hardware reset button, or click the Back button in your current browser.
Behavior During Times of Network Congestion
Anything that degrades network performance can affect voice and video quality, and in some cases, can cause a call to drop. Sources of network degradation can include, but are not limited to, the following activities:
Administrative tasks, such as an internal port scan or security scan
Attacks that occur on your network, such as a Denial of Service attack
To reduce or eliminate any adverse effects to the devices, schedule administrative network tasks during a time when the devices are not being used or exclude the devices from testing.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)