Table Of Contents
Cisco Analog Video Gateway XML API Guide
Syntax
Examples
Video Port and Profile Configuration
Video Port
ListVideoPorts
GetVideoPortConfig
GetVideoPortCapability
ModifyVideoPortConfig
Video Codec Profile
ListVideoCodecProfiles
GetVideoCodecProfile
CreateVideoCodecProfile
ModifyVideoCodecProfile
DeleteVideoCodecProfile
Video Stream Profile
ListVideoStreamProfile
GetVideoStreamProfile
CreateVideoStreamProfile
ModifyVideoStreamProfile
DeleteVideoStreamProfile
Video Motion Region Profile
ListVideoMotionRegion
GetVideoMotionRegion
CreateVideoMotionRegion
ModifyVideoMotionRegion
DeleteVideoMotionRegion
Video Motion Detection Profile
ListVideoMotionDetection
GetVideoMotionDetection
CreateVideoMotionDetection
ModifyVideoMotionDetection
DeleteVideoMotionDetection
RS-485 Serial Port Configuration
ListAllSerialPorts
GetSerialPortConfig
GetSerialPortCapability
ModifySerialPortConfig
WriteSerialPort
ReadSerialPort
Contact Closure Configuration
ListCCPorts
GetCCPortConfig
GetCCPortCapability
ModifyCCPortConfig
GetCCPortHWStates
Alarm Monitors
Destination Profile
ListDestinationProfiles
GetDestinationProfile
CreateDestinationProfile
ModifyDestinationProfile
DeleteDestinationProfile
Monitor Profile
ListMonitorProfiles
GetMonitorProfile
CreateMonitorProfile
ModifyMonitorProfile
DeleteMonitorProfile
Notifier Profile
ListNotifierProfile
GetNotifierProfile
CreateNotifierProfile
ModifyNotifierProfile
DeleteNotifierProfile
Saving Configurations
Error Codes
Video Error Codes
RS485 Serial Port Error Codes
Contact Closure Port Error Codes
Alarm Monitor Profile Error Codes
Other Error Codes
Additional References
Related Documents
Technical Assistance
Cisco Analog Video Gateway XML API Guide
Last Updated: August 18, 2009
Text Part Number: OL-15451-04
This guide provides information on the XML application programming interfaces (APIs) required to configure the Cisco Analog Video Gateway video port profiles. These profiles are configured using Cisco IOS CLIs or XML APIs. For information on using CLIs to configure the video port profiles, see the Cisco Analog Video Gateway CLI Administrator Guide.
This guide supports features for version 1.2 and earlier versions of the Cisco Analog Video Gateway network module. To view the product feature history, see the Release Notes for the Cisco Video Management and Storage System, which lists feature support for Cisco Analog Video Gateway versions.
This guide contains the following sections:
•Syntax
•Video Port and Profile Configuration
•RS-485 Serial Port Configuration
•Contact Closure Configuration
•Alarm Monitors
•Saving Configurations
•Error Codes
•Additional References
Syntax
This section describes the syntax used for the XML APIs.
The client uses the URL http://host_name_or_ipaddress/ipvs/IpvsXmlServlet to send the XML request document using the POST method when the video network module acts as a server.
Format
The XML document used in a request operation has the following generic format:
•<xxx>yyy</xxx>
–xxx is the request operation using GetVideoPortConfig, ModifyVideoPortConfig.
–yyy is the parameter of this request operation xxx. Multiple request operations can be specified in the same document.
When onfail= "ignore" is specified, and multiple xxx request operations are contained in the same request document, the next request operation is automatically processed if the current operation fails.
When onfail= "abort" is specified, the processing halts if the current request operation fails.
<?xml version="1.0" encoding="UTF-8" standalone="yes"?>
<ops type="request" onfail="ignore" rid="1234">
<xxx cseq="1" cvers="1.0">
Examples
Successful Request and Response
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<CreateVideoStreamProfile cseq="1"
cvers="1.0">
<codecProfileTag>codec010</codecProf
ileTag>
</CreateVideoStreamProfile>
<GetVideoStreamProfile cseq="2"
cvers="1.0">
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<CreateVideoStreamProfile cseq="1"
cvers="1.0" cservs="1.0">
</CteateVideoStreamProfile>
<GetVideoStreamProfile cseq="2" cvers="1.0"
cservs="1.0">
<description></description>
|
Failed Request and Response
Here is an example of a failed request and response due to a validation error. In the XML request, the value of codecProfileTag is out of the supported range.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<CreateVideoStreamProfile cseq="1"
cvers="1.0">
<codecProfileTag>stream010</codecPr
ofileTag>
</CreateVideoStreamProfile>
<GetVideoStreamProfile cseq="2"
cvers="1.0">
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<CreateVideoStreamProfile cseq="1"
cvers="1.0" cservs="1.0">
<result code="10">Error in XML document
at line 5. Message: cvc-pattern-valid:
Value `stream010' is not facet-valid with
respect to pattern
`[c][o][d][e][c][0-9][0-9][0-9]' for type
CODECtagType'.</result/>
</CteateVideoStreamProfile>
|
Video Port and Profile Configuration
Video Port
Use the following APIs to get the video port configuration and modify video port parameters.
•ListVideoPorts
•GetVideoPortConfig
•GetVideoPortCapability
•ModifyVideoPortConfig
ListVideoPorts
Lists all the configured video port numbers.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<ListVideoPorts cseq="1" cvers="1.0"/>
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<ListVideoPorts cseq="1" cvers="1.0"
svers="1.0">
|
GetVideoPortConfig
Gets the specified video port configuration.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<GetVideoPortConfig cseq="1" cvers="1.0">
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<GetVideoConfig cseq="1" cvers="1.0"
svers="1.0">
<description>XXXXX</description>
<direction>in</direction>
<maxResolution>cif</maxResolution>
<brightness>0</brightness>
<saturation>0</saturation>
|
GetVideoPortCapability
Lists all the video port configurable parameters, their valid ranges and default values.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<GetVideoPortCapability cseq="1"
cvers="1.0"/>
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<GetVideoPortCapability cseq="1"
cvers="1.0" svers="1.0">
<portNum required="yes"
default="no">0-15</portNum>
<state required="no"
default="enabled">enabled,
disabled</state>
<description required="no"
default="">xxx</description>
<direction required="no"
default="in">in, out</direction>
<maxResolution required=''no''
default=''4cif''>cif,
4cif</maxResolution>
<brightness required="no"
default="0">-128 to 127</brightness>
<contrast required="no"
default="0">-128 to 127</contrast>
<hue required="no" default="0">-128 to
127</hue>
<saturation required="no"
default="0">-128 to 127</saturation>
<sharpness required="no"
default="0">0-3</sharpness>
</GetVideoPortCapability>
|
ModifyVideoPortConfig
Modifies one or more parameters of the specified video port.
Brightness, maxResolution, contrast, hue, saturation, and sharpness are only applicable to input and are ignored for output. Their values change to default values when the direction is changed from input to output.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<ModifyVideoPortConfig cseq="1"
cvers="1.0">
<description>XXXXX</description>
<direction>in</direction>
<maxResolution>cif</maxResolution>
<brightness>-128 to 127</brightness>
<contrast>-128 to 127</contrast>
<saturation>-128 to 127</saturation>
<sharpness>0-3</sharpness>
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<ModifyVideoPortConfig cseq="1"
cvers="1.0" svers="1.0">
|
Video Codec Profile
Configure the video codec profile with the following APIs:
•ListVideoCodecProfiles
•GetVideoCodecProfile
•CreateVideoCodecProfile
•ModifyVideoCodecProfile
•DeleteVideoCodecProfile
ListVideoCodecProfiles
Lists all the configured video codec profile tags in the system.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<ListVideoCodecProfiles cseq="1"
cvers="1.0"/>
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<ListVideoCodecProfiles cseq="1"
cvers="1.0" svers="1.0">
</ListVideoCodecProfiles>
|
GetVideoCodecProfile
Gets the specified video codec profile.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<GetVideoCodecProfile cseq="1"
cvers="1.0">
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<GetVideoCodecProfile cseq="1"
cvers="1.0" svers="1.0">
<description>XXXXX</description>
<frameRate>29.97</frameRate>
<resolution>cif</resolution>
<qualityFactor>70</qualityFactor>
<skipFactor>1</skipFactor>
<maxBitRate>384</maxBitRate>
|
CreateVideoCodecProfile
Creates the specified video codec profile, where:
•+ maxBitRate value range: 168-2000 (MPEG4) and 168-3000 (H264).
•+ qualityFactor is only applicable to codec type MJPEG.
•+ gopSize is only applicable to a non-MJPEG codec type.
•+ bit CBR is only applicable to a non-MJPEG codec type.
•+ frameRate value range: NTSC= 30-0.1, PAL = 25-0.0833. The skipFactor is used if skipFactor and frameRate are specified in the request. The frame rate adjusts to a different value based on the new skipFactor value.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<CreateVideoCodecProfile cseq="1"
cvers="1.0">
<tag>codec000-codec999</tag>
<description>XXXXX</description>
<codec>h264,mpeg4,mjpeg</codec>
<format>ntsc,pal</format>
<qualityFactor>1-100</qualityFactor>
<bitRate>cbr, vbr</bitRate>
<maxBitRate>168-3000</maxBitRate>
<skipFactor>1-300</skipFactor>
</CreateVideoCodecProfile>
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<CreateVideoCodecProfile cseq="1"
cvers="1.0">
</CreateVideoCodecProfile>
|
ModifyVideoCodecProfile
Modifies the specified video codec profile configuration, where:
•+ maxBitRate value range:168-2000 (MPEG4) and 168-3000 (H264).
•+ qualityFactor is only applicable to codec type MJPEG
•+ gopSize is only applicable to a non-MJPEG codec type
•+ bitRate CBR is only applicable to a non-MJPEG codec type
•+ frameRate value range:NTSC= 30-0.1, PAL = 25-0.0833. The skipFactor is used if skipFactor and frameRate are specified in the request. The frame rate value adjusts to a different value based on the new skipFactor value.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<ModifyVideoCodecProfile cseq="1"
cvers="1.0">
<tag>codec000-codec999</tag>
<description>XXXXX</description>
<codec>h264, mpeg4, mjpeg</codec>
<format>ntsc, pal</format>
<qualityFactor>1-100</qualityFactor>
<bitRate>cbr, vbr</bitRate>
<maxBitRate>168-3000</maxBitRate>
<skipFactor>1-300</skipFactor>
</ModifyVideoCodecProfile>
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<ModifyVideoCodecProfile cseq="1"
cvers="1.0" svers="1.0">
</ModifyVideoCodecProfile>
|
DeleteVideoCodecProfile
Deletes the specified video Codec Profile.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<DeleteVideoCodecProfile cseq="1"
cvers="1.0">
</DeleteVideoCodecProfile>
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<DeleteVideoCodecProfile cseq="1"
cvers="1.0">
</DeleteVideoCodecProfile>
|
Video Stream Profile
Configure the video stream profile with the following APIs:
•ListVideoStreamProfile
•GetVideoStreamProfile
•CreateVideoStreamProfile
•ModifyVideoStreamProfile
•DeleteVideoStreamProfile
ListVideoStreamProfile
Lists all the video stream profiles.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<ListVideoStreamProfiles cseq="1"
cvers="1.0"/>
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<ListVideoStreamProfiles cseq="1"
cvers="1.0" svers="1.0">
</ListVideoStreamProfiles>
|
GetVideoStreamProfile
Gets the specified video stream profile.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0"
encoding="UTF-8"
standalone="yes"?>
<ops type="request"
onfail="ignore" rid="1234">
<GetVideoStreamProfile
cseq="1" cvers="1.0">
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="reply" onfail="ignore" rid="1234">
<GetVideoStreamProfile cseq="1" cvers="1.0"
svers="1.0">
<description></description>
<codecProfileTag>codec000</codecProfileTag>
<motionDetectionTag>md000</motionDetectionTag>
<rtcpRemoteInactive>system</rtcpRemoteInactive>
<rtcpRemoteBye>system</rtcpRemoteBye>
<rtcpEventTimer>25</rtcpEventTimer>
<icmpEventTimer>5</icmpEventTimer>
<icmpUnreachable>system</icmpUnreachable>
|
CreateVideoStreamProfile
Creates the specified video stream profile.
The specified video codec profile must exist before this configuration is processed successfully.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0"encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<CreateVideoStreamProfile cseq="1"
cvers="1.0">
<description>stream profile 010
config</description>
<codecProfileTag>codec000-codec999</codecPr
ofileTag>
<motionDetectionTag>md000-md999</motionDete
ctionTag>
<rtcpEventTimer>25</rtcpEventTimer>
<rtcpRemoteInactive>enabled</rtcpRemoteInac
tive>
<rtcpRemoteBye>enabled</rtcpRemoteBye>
<icmpEventTimer>10</icmpEventTimer>
<icmpUnreachable>enabled</icmpUnreachable>
</CreateVideoStreamProfile>
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<CreateVideoStreamProfile cseq="1"
cvers="1.0" svers="1.0">
</CreateVideoStreamProfile>
|
ModifyVideoStreamProfile
Modifies the specified video stream profile.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0"encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<ModifyVideoStreamProfile cseq="1"
cvers="1.0">
<description>stream profile 010
config</description>
<codecProfileTag>codec000-codec999</codecPr
ofileTag>
<motionDetectionTag>md000-md999</motionDete
ctionTag>
<rtcpEventTimer>25</rtcpEventTimer>
<rtcpRemoteInactive>enabled</rtcpRemoteInac
tive>
<rtcpRemoteBye>enabled</rtcpRemoteBye>
<icmpEventTimer>10</icmpEventTimer>
<icmpUnreachable>enabled</icmpUnreachable>
</ModifyVideoStreamProfile>
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<ModifyVideoStreamProfile cseq="1"
cvers="1.0" svers="1.0">
</ModifyVideoStreamProfile>
|
DeleteVideoStreamProfile
Deletes the specified video stream profile.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<DeleteVideoStreamProfile cseq="1"
cvers="1.0">
</DeleteVideoStreamProfile>
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<DeleteVideoStreamProfile cseq="1"
cvers="1.0" svers="1.0">
</DeleteVideoStreamProfile>
|
Video Motion Region Profile
Configure the video motion region profile with the following APIs:
•ListVideoMotionRegion
•GetVideoMotionRegion
•CreateVideoMotionRegion
•ModifyVideoMotionRegion
•DeleteVideoMotionRegion
ListVideoMotionRegion
Lists all the configured video motion region profile tags.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<ListVideoMotionRegions cseq="1"
cvers="1.0"/>
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<ListVideoMotionRegions cseq="1"
cvers="1.0" svers="1.0">
</ListVideoMotionRegions>
|
GetVideoMotionRegion
Gets the specified video motion region profile.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<GetVideoMotionRegion cseq="1" cvers="1.0">
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<GetVideoMotionRegion cseq="1" cvers="1.0"
svers="1.0">
<description>XXXXX</description>
<upperLeftCoordx>20</upperLeftCoordx>
<upperLeftCoordy>50</upperLeftCoordy>
<lowerRightCoordx>100</lowerRightCoordx>
<lowerRightCoordy>100</lowerRightCoordy>
<threshold>20</threshold>
|
CreateVideoMotionRegion
Creates the specified video motion region profile.
The upper left coordinates x and y have default values of zero. The origin (0,0) is the upper left corner.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<CreateVideoMotionRegion cseq="1"
cvers="1.0">
<description>XXXXX</description>
<upperLeftCoordx>0-352</upperLeftCoordx>
<upperLeftCoordy>0-287</upperLeftCoordy>
<lowerRightCoordx>0-351</lowerRightCoordx>
<lowerRightCoordy>0-287</lowerRightCoordy>
<threshold>1-100</threshold>
</CreateVideoMotionRegion>
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<CreateVideoMotionRegion cseq="1"
cvers="1.0">
</CreateVideoMotionRegion>
|
ModifyVideoMotionRegion
Modifies the specified video motion region profile.
The upper left coordinates x and y have default values of zero. The origin (0,0) is the upper left corner.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<modifyVideoMotionRegion cseq="1"
cvers="1.0">
<description>XXXXX</description>
<upperLeftCoordx>0-351</upperLeftCoordx>
<upperLeftCoordy>0-287</upperLeftCoordy>
<lowerRightCoordx>0-351</lowerRightCoordx>
<lowerRightCoordy>0-287</lowerRightCoordy>
<threshold>1-100</threshold>
</modifyVideoMotionRegion>
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<modifyVideoMotionRegion cseq="1"
cvers="1.0" svers="1.0">
</modifyVideoMotionRegion>
|
DeleteVideoMotionRegion
Deletes the specified video motion region profile.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<DeleteVideoMotionRegion cseq="1"
cvers="1.0">
</DeleteVideoMotionRegion>
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<DeleteVideoMotionRegion cseq="1"
cvers="1.0" svers="1.0">
</DeleteVideoMotionRegion>
|
Video Motion Detection Profile
Configure the video motion detection profile with the following APIs:
•ListVideoMotionDetection
•GetVideoMotionDetection
•CreateVideoMotionDetection
•ModifyVideoMotionDetection
•DeleteVideoMotionDetection
ListVideoMotionDetection
Lists all the video motion detection profiles.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<ListVideoMotionDetections cseq="1"
cvers="1.0"/>
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<ListVideoMotionDetections cseq="1"
cvers="1.0" svers="1.0">
</ListVideoMotionDetections>
|
GetVideoMotionDetection
Gets the specified video motion detection profile.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<GetVideoMotionDetection cseq="1"
cvers="1.0">
</GetVideoMotionDetection>
|
?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
ops type="reply" onfail="ignore"
rid="1234">
<GetVideoMotionDetection cseq="1"
cvers="1.0" svers="1.0">
<description>XXXXX</description>
<motionRegionTag
tagNum="0">mr000</motionRegionTag>
<motionRegionTag
tagNum="31">mr031</motionRegionTag>
</GetVideoMotionDetection>
|
CreateVideoMotionDetection
Creates the specified video motion detection profile.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<CreateVideoMotionDetection cseq="1"
cvers="1.0">
<tag>md000-md999<tag>
(required)
<description>XXXXX</description>
<motionRegionTag
tagNum="0">mr000</motionRegionTag>
<motionRegionTag
tagNum="31">mr031</motionRegionTag>
</CreateVideoMotionDetection>
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<CreateVideoMotionDetection cseq="1"
cvers="1.0" svers="1.0">
</CreateVideoMotionDetection>
|
ModifyVideoMotionDetection
Modifies the specified video motion detection profile.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<ModifyVideoMotionDetection cseq="1"
cvers="1.0">
<tag>md000-md999<tag>
(required)
<description>XXXXX</description>
<motionRegionTag
tagNum="0">mr000</motionRegionTag>
<motionRegionTag
tagNum="31">mr031</motionRegionTag>
</ModifyVideoMotionDetection>
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<ModifyVideoMotionDetection cseq="1"
cvers="1.0" svers="1.0">
</ModifyVideoMotionDetection>
|
DeleteVideoMotionDetection
Deletes the specified video motion detection profile.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<DeleteVideoMotionDetection cseq="1"
cvers="1.0">
</DeleteVideoMotionDetection>
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<DeleteVideoMotionDetection cseq="1"
cvers="1.0" svers="1.0">
</DeleteVideoMotionDetection>
|
RS-485 Serial Port Configuration
Configure control and monitor, pan, tilt, and zoom (PTZ) camera movements through this serial port connection.
The RS-485 serial port is configured with the following APIs:
•ListAllSerialPorts
•GetSerialPortConfig
•GetSerialPortCapability
•ModifySerialPortConfig
•WriteSerialPort
•ReadSerialPort
ListAllSerialPorts
Lists all the serial ports in the system.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<ListSerialPorts cseq="1" cvers="1.0"/>
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<ListSerialPorts cseq="1" cvers="1.0"
svers="1.0">
|
GetSerialPortConfig
Gets the specified serial port configuration.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<GetSerialPortConfig cseq="1" cvers="1.0">
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<GetSerialPortConfig cseq="1" cvers="1.0"
svers="1.0">
<description>XXXXX</description>
<baudrate>9600</baudrate>
<termination-State>connected</termination-S
tate>
|
GetSerialPortCapability
Gets the serial port parameters and their default values and allowable ranges.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0"
encoding="ISO-8859-1"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<GetSerialPortCapability cseq="1"
cvers="1.0"/>
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="reply" onfail="ignore" rid="1234">
<GetSerialPortCapability cseq="1" cvers="1.0"
svers="1.0">
<portNum required="yes"
default="no">0-1</portNum>
<description required="no"
default="">xxx</description>
<state required="no" default="enable>enabled,
disabled</state>
<baudrate required="no"
default="9600">300,600,1200,2400,480,9600,19200,
38400,57600,115200</baudrate>
<databits required="no"
default="8">8,7,6,5</databits>
<stopbits required="no"default="1">1,1.5,
2</stopbits>
<parity required="no" default="none">none,odd,
even,mark,space</parity>
<termination-State required="no"
default="open">open,
connected</termination-State>
</GetSerialPortCapability>
|
ModifySerialPortConfig
Modifies one or more serial port parameters of the specified serial port.
Client -> Server: Request
|
Server -> Client: Response
|
<ops type="request" onfail="ignore"
rid="1234">
<ModifySerialPortConfig cseq="1"
cvers="1.0">
<description>XXXXX</description>
<baudrate>9600</baudrate>
<termination-state>connected</termination-S
tate>
</ModifySerialPortConfig>
|
<ops type="reply" onfail="ignore"
rid="1234">
<ModifySerialPortConfig cseq="1"
cvers="1.0" svers="1.0">
</ModifySerialPortConfig>
|
WriteSerialPort
Controls pan, tilt, and zoom (PTZ) camera movements, or queries PTZ camera positions, where:
•Data has the format 0x + a pair of characters (0-9, A-F, a-f).
•maxReadBytes is optional.
•The timeout timer is optional. Its default value is 500 ms if not specified.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<WriteSerialPort cseq="1" cvers="1.0">
<data>0x1234567890ABCEDF</data>
<maxReadBytes>x</maxReadBytes>
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<WriteSerialPort cseq="1" cvers="1.0"
svers="1.0">
<data>0x1234567890ABCDEF</data>
|
ReadSerialPort
Reads the number of bytes from the specified serial port.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<ReadSerialPort cseq="1" cvers="1.0">
<maxReadBytes>x</maxReadBytes>
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<ReadSerialPort cseq="1" cvers="1.0"
svers="1.0">
<data>0x1234567890ABCDEF</data>
|
Contact Closure Configuration
Contact closure (CC) is configured with the following APIs:
•ListCCPorts
•GetCCPortConfig
•GetCCPortCapability
•ModifyCCPortConfig
•GetCCPortHWStates
ListCCPorts
Lists all the configured contact closure ports.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<ListCCPorts cseq="1" cvers="1.0"/>
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<ListCCPorts cseq="1" cvers="1.0"
svers="1.0">
|
GetCCPortConfig
Gets the specified contact closure port configuration.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<GetCCPortConfig cseq="1" cvers="1.0">
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<GetCCConfig cseq="1" cvers="1.0"
svers="1.0">
<description>XXXXX</description>
<direction>in</direction>
<relayState>open</relayState>
|
GetCCPortCapability
Gets contact closure port capability.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<GetCCPortCapability cseq="1" cvers="1.0"/>
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<GetCCPortCapability cseq="1" cvers="1.0"
svers="1.0">
<portNum required="yes"
default="no">0-7</portNum>
<description required="no"
default="">xxx</description>
<state required="no"
default="disabled">enabled,
disabled</state>
<direction required="no" default="in">in,
out</direction>
<relayState required="no"
default="close">open, close</relayState>
|
ModifyCCPortConfig
Modifies one or more parameters of the specified contact closure port.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<ModifyCCPortConfig cseq="1" cvers="1.0">
<description>XXXXX</description>
<direction>in</direction>
<relayState>open</relayState>
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<ModifyCCPortConfig cseq="1" cvers="1.0"
svers="1.0">
|
GetCCPortHWStates
Gets the hardware status of all contact closure ports.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<GetCCPortHWStates cseq="1" cvers="1.0" />
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<GetCCPortHWStates cseq="1" cvers="1.0"
svers="1.0">
|
Alarm Monitors
The alarm software module serves as a central point for the control of all alarm and relay interfaces in the video service module. All four relay outputs in the video service module can be accessed by multiple users. However, each interface can be operated by only one user at a time.
When a relay output port is seized, it is not available to other users until the current user has finished operations and releases the interface. The alarm monitor watches for any alarm event on every alarm interface. When an event is triggered, it notifies the alarm application which passes the information to the configured monitor destination.
This section consists of:
Destination Profile
Monitor Profile
Notifier Profile
Destination Profile
Configure the destination profile with the following APIs:
•ListDestinationProfiles
•GetDestinationProfile
•CreateDestinationProfile
•ModifyDestinationProfile
•DeleteDestinationProfile
ListDestinationProfiles
Lists all configured destination profiles.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<ListDestinationProfiles cseq="1"
cvers="1.0"/>
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<ListDestinationProfiles cseq="1"
cvers="1.0" svers="1.0">
</ListDestinationProfiles>
|
GetDestinationProfile
Gets the specified destination profile configuration.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<GetDestinationProfile cseq="1"
cvers="1.0">
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<GetDestinationProfile cseq="1" cvers="1.0"
svers="1.0">
<tag>dest000-dest999</tag>
<description>XXXXX</description>
<primaryUrl>http://172.20.30.40:8080/servle
t/monitor</primaryUrl>
<secondaryUrl>http://172.20.30.40:8080/serv
let/monitor</secondaryUrl>
|
CreateDestinationProfile
Creates the specified destination profile configuration.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<CreateDestinationProfile cseq="1"
cvers="1.0">
<description>XXXXX</description>
<primaryUrl>url definition</primaryUrl>
<secondaryUrl>url
definition</secondaryuUrl>
</CreateDestinationProfile>
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<CreateDestinationProfile cseq="1"
cvers="1.0" svers="1.0">
</CreateDestinationProfile>
|
ModifyDestinationProfile
Modifies the specified destination profile configuration.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<ModifyDestinationProfile cseq="1"
cvers="1.0">
<description>XXXXX</description>
<primaryUrl>url definition</primaryUrl>
<secondaryUrl>url definition</secondaryUrl>
</ModifyDestinationProfile>
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<ModifyDestinationProfile cseq="1"
cvers="1.0" svers="1.0">
</ModifyDestinationProfile>
|
DeleteDestinationProfile
Deletes the specified destination profile configuration.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<DeleteDestinationProfile cseq="1"
cvers="1.0">
</DeleteDestinationProfile>
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<DeleteDestinationProfile cseq="1"
cvers="1.0" svers="1.0">
</DeleteDestinationProfile>
|
Monitor Profile
Configure the monitor profile with the following APIs:
•ListMonitorProfiles
•GetMonitorProfile
•CreateMonitorProfile
•ModifyMonitorProfile
•DeleteMonitorProfile
ListMonitorProfiles
Lists all the configured alarm monitor profile tags in the system.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<ListMonitorProfiles cseq="1" cvers="1.0"/>
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<ListMonitorProfiles cseq="1" cvers="1.0"
svers="1.0">
|
GetMonitorProfile
Gets the specified monitor profile configuration.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<GetMonitorProfile cseq="1" cvers="1.0">
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<GetMonitorProfile cseq="1" cvers="1.0"
svers="1.0">
<description>XXXXX</description>
<sourceTrigger>cc0</sourceTrigger>
<event>ccport-open-to-close</event>
|
CreateMonitorProfile
Creates the specified monitor profile configuration.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<CreateMonitorProfile cseq="1" cvers="1.0">
<description>XXXXX</description>
<sourcePort>vp0-vp15,cc0-cc7</sourcePort>
<triggerProfileTag>trigxxx</triggerProfileT
ag>
<sourceTrigger>vp0-vp15,vp-any,cc0-cc7,stre
am000-stream999,system</sourceTrigger>
<event>ccport-open-to-close,
ccport-close-to-open,
ccport-any-state-change,
vport-state-change,vport-signal-change,
vport-signal-detect,vport-signal-loss,video
-motion-detection, system-reload</event>
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<CreateMonitorProfile cseq="1" cvers="1.0"
svers="1.0">
|
ModifyMonitorProfile
Modifies the specified monitor profile configuration.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<ModifyMonitorProfile cseq="1" cvers="1.0">
<description>XXXXX</description>
<sourceTrigger>vp0-vp15,cc0-cc7,stream000-s
tream999system</sourceTrigger>
<event>ccport-open-to-close,ccport-close-to
-open,ccport-any-state-change,
vport-state-change,vport-signal-loss,video-
motion-detection,system-reload</event>
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<ModifyMonitorProfile cseq="1" cvers="1.0"
svers="1.0">
|
DeleteMonitorProfile
Deletes the specified monitor profile configuration.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<DeleteMonitorProfile cseq="1" cvers="1.0">
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<DeleteMonitorProfile cseq="1" cvers="1.0"
svers="1.0">
|
Notifier Profile
Configure the notifier profile with the following APIs:
•ListNotifierProfile
•GetNotifierProfile
•CreateNotifierProfile
•ModifyNotifierProfile
•DeleteNotifierProfile
ListNotifierProfile
Lists all the configured notifier profile tags in the system.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<ListNotifierProfiles cseq="1"
cvers="1.0"/>
|
<ops type="reply" onfail="ignore"
rid="1234">
<ListNotifierProfiles cseq="1" cvers="1.0"
svers="1.0">
|
GetNotifierProfile
Gets the specified notifier profile configuration.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<GetNotifierProfile cseq="1" cvers="1.0">
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<GetNotifierProfile cseq="1" cvers="1.0"
svers="1.0">
<description>XXXXX</description>
<monitorTag>mon000</monitorTag>
<destinationTag>trig000</destinationTag>
|
CreateNotifierProfile
Creates the specified notifier profile configuration.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<CreateNotifierProfile cseq="1"
cvers="1.0">
<description>XXXXX</description>
<monitorProfileTag>mon000-mon999</monitorTa
g>
<destinationProfileTag>dest000-dest999</des
tinationTag>
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<CreateNotifierProfile cseq="1" cvers="1.0"
svers="1.0">
|
ModifyNotifierProfile
Modifies the specified notifier profile configuration.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<ModifyNotifierProfile cseq="1"
cvers="1.0">
<description>XXXXX</description>
<monitorProfileTag>mon000-mon999</monitorTa
g>
<destinationProfileTag>dest000-dest999</des
tinationTag>
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<ModifyNotifierProfile cseq="1" cvers="1.0"
svers="1.0">
|
DeleteNotifierProfile
Deletes the specified notifier profile configuration.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<DeleteNotifierProfile cseq="1"
cvers="1.0">
|
<?xml version="1.0" encoding="ISO-8859-1"
standalone="yes"?>
<ops type="request" onfail="ignore">
<DeleteNotifierProfile cseq="1" cvers="1.0"
svers="1.0">
|
Saving Configurations
Use SaveConfig to save the configuration so that it can be restored during the next reboot.
Client -> Server: Request
|
Server -> Client: Response
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="request" onfail="ignore"
rid="1234">
<SaveConfig cseq="1" cvers="1.0"/>
|
<?xml version="1.0" encoding="UTF-8"
standalone="yes"?>
<ops type="reply" onfail="ignore"
rid="1234">
<SaveConfig cseq="1" cvers="1.0"
svers="1.0">
|
Error Codes
A response contains an error code with a value other than zero when a request is not successfully processed because of an XML syntax error or a value that is out of range.
This section consists of:
Video Error Codes
RS485 Serial Port Error Codes
Contact Closure Port Error Codes
Alarm Monitor Profile Error Codes
Other Error Codes
Video Error Codes
Error Codes
|
Description
|
101 |
The specified video codec profile does not exist. |
102 |
The specified video codec profile already exists. |
103 |
Failed to create video codec profile. |
104 |
Failed to delete video codec profile. |
105 |
Video stream profile does not exist. |
106 |
Video stream profile already exists. |
107 |
Failed to create video stream profile. |
108 |
Failed to delete video stream profile. |
109 |
Motion region profile does not exist. |
110 |
Motion region profile already exists. |
111 |
Failed to create motion region profile. |
112 |
Failed to delete motion region profile. |
113 |
Motion detection profile does not exist. |
114 |
Motion detection profile already exists. |
115 |
Failed to create motion detection profile. |
116 |
Failed to delete motion detection profile. |
117 |
Only video ports 0-1 can be output ports. |
119 |
Upper left coordinate x must be smaller than lower right coordinate x. |
120 |
Upper left coordinate y must be smaller than lower right coordinate y. |
121 |
The maxBitRate value is out of range (168-2000). |
122 |
Format and frame rate values are not compatible. |
123 |
The specified codec profile is in use. |
124 |
The specified motion region profile is in use. |
125 |
The specified motion detection profile is in use. |
126 |
The specified stream profile is in use. |
128 |
The specified bitRate and gopSize are not compatible. |
129 |
The specified skipFactor value is not valid. |
130 |
An exception is encountered when reading the video port LED status. |
131 |
The video port maxResolution is lower than the codec profile resolution. |
RS485 Serial Port Error Codes
Error Codes
|
Description
|
401 |
Data cannot be read. |
402 |
Encountered a read exception. |
403 |
Failed to read all requested bytes. |
404 |
Encountered a write exception. |
405 |
Port is disabled and a read or write request is rejected. |
Contact Closure Port Error Codes
Error Codes
|
Description
|
201 |
Only contact closure (cc) port numbers 0-3 can be configured for output. |
Alarm Monitor Profile Error Codes
Error Codes
|
Description
|
301 |
Destination profile does not exist. |
302 |
Destination profile already exists. |
303 |
Failed to create destination profile. |
304 |
Failed to delete destination profile. |
305 |
Monitor profile does not exist. |
306 |
Monitor profile already exists. |
307 |
Failed to create monitor profile. |
308 |
Failed to delete monitor profile. |
309 |
Notifier profile does not exist. |
310 |
Notifier profile already exists. |
311 |
Failed to create notifier profile. |
312 |
Failed to delete notifier profile. |
313 |
Video motion detection profile does not exist. |
314 |
Event and source trigger values are not compatible. |
Other Error Codes
Error Codes
|
Description
|
10 |
Detected an XML syntax error in the request document. |
11 |
Failed to proceed because of an internal resource problem. |
12 |
Failed to save configuration because of an internal system source error. |
Additional References
The following sections provide references related to the Cisco Analog Video Gateway application.
Related Documents
Technical Assistance
Description
|
Link
|
For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: Subscribe to the What's New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0. |
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html |
Cisco Feature Navigator website |
http://www.cisco.com/go/cfn Use Cisco Feature Navigator to find information about platform support and Cisco IOS and Catalyst OS software image support. An account on Cisco.com is not required. |
Cisco Software Center website |
http://www.cisco.com/public/sw-center/ |
CCDE, CCENT, CCSI, Cisco Eos, Cisco HealthPresence, Cisco Ironport, the Cisco logo, Cisco Lumin, Cisco Nexus, Cisco Nurse Connect, Cisco Stackpower, Cisco StadiumVision, Cisco TelePresence, Cisco Unified Computing System, Cisco WebEx, DCE, Flip Channels, Flip for Good, Flip Mino, Flip Video, Flip Video (Design), Flipshare (Design), Flip Ultra, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn, Cisco Store, and Flip Gift Card are service marks; and Access Registrar, Aironet, AsyncOS, Bringing the Meeting To You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Collaboration Without Limitation, EtherFast, EtherSwitch, Event Center, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, iQuick Study, IronPort, the IronPort logo, LightStream, Linksys, MediaTone, MeetingPlace, MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, Network Registrar, PCNow, PIX, PowerPanels, ProConnect, ScriptShare, SenderBase, SMARTnet, Spectrum Expert, StackWise, The Fastest Way to Increase Your Internet Quotient, TransPath, WebEx, and the WebEx logo are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.
All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0907R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.
Copyright © 2009 Cisco Systems, Inc. All rights reserved.