Commands

This chapter includes the following sections:

activate (firmware)

To activate CIMC firmware, use the activate command.

activate

This command has no arguments or keywords.

Command Default

None

Command Modes

Firmware (/cimc/firmware)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to activate CIMC firmware: 

server# scope cimc
server /cimc # scope firmware
server /cimc/firmware # activate
server /cimc/firmware #

Related Commands

Command

Description

show cimc

 

show version

 

clear (log)

To clear the CIMC log, use the clear command in log mode.

clear

This command has no arguments or keywords.

Command Default

None

Command Modes

Log (/cimc/log)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to clear the CIMC log: 

server# scope cimc
server /cimc # scope log
server /cimc/log # clear
server /cimc/log #

Related Commands

Command

Description

show sel

 

show sensor

 

clear (sel)

To clear the system event log, use the clear command in sel mode.

clear

This command has no arguments or keywords.

Command Default

None

Command Modes

SEL (/sel)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to clear the system event log: 

server# scope sel
server /sel # clear
server /sel #

Related Commands

Command

Description

show sel

 

show sensor

 

commit

To save configuration changes, use the commit command.

commit

This command has no arguments or keywords.

Command Default

None

Command Modes

Any command mode

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to save a configuration change: 

server# set cli output yaml
CLI output format set to yaml
server# commit
server#

connect

To connect to either the server CLI or the server shell, use the connect command.

connect { host | shell }

Syntax Description

host

Specifies the CLI on the server.

shell

Specifies the GNU bash shell on the server.

Command Default

None

Command Modes

Any command mode

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

Use the exit command to exit the server shell.

Examples

This example shows how to connect to the server shell: 

server# connect shell
bash-3.2

discard

To discard all configurations, use the discard command.

discard

This command has no arguments or keywords.

Command Default

None

Command Modes

Any command mode

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to discard all configurations: 

server# discard
server#

exit

To leave any mode, use the exit command.

exit

This command has no arguments or keywords.

Command Default

None

Command Modes

Any command mode

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to exit bios mode: 

server /bios # exit
server#

factory-default

To set the server to factory default, use the factory-default command.

factory-default

This command has no arguments or keywords.

Command Default

None

Command Modes

CIMC (/cimc)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to set the server to factory default: 

server# scope cimc
server /cimc # factory-default
This operation will reset the BMC configuration to factory default.
All your configuration will be lost.
Continue?[y|n] y

generate-csr

To generate a Certificate Request Signing (CSR), use the generate-csr command.

generate csr

This command has no arguments or keywords.

Command Default

None

Command Modes

Certificate (/certificate)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to generate a CSR : 

server# scope certificate
server /certificate # generate-csr
Common Name (CN): abcCertificate
Organization Name (O): abcCo
Organization Unit (OU): 01
Locality (L): west
StateName (S): CA
Country Code (CC): US
Email: abcCo@abcCo.com
Continue to generate CSR?[y|N] y

-----BEGIN CERTIFICATE REQUEST-----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-----END CERTIFICATE REQUEST-----

server /certificate #

Related Commands

Command

Description

show certificate

 

show ssh

 

power

To manage server power, use the power command.

power {cycle | hard-reset | off | on | shutdown}

Syntax Description

cycle

Specifies server power cycle.

hard-reset

Specifies server hard reset.

off

Specifies server power off.

on

Specifies server power on.

shutdown

Specifies server shutdown.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to power off the server : 

server# scope chassis
server /chassis # power off
This operation will change the server's power state.
Continue?[y|n] y

Usage Guidelines


  • Cycle—Power off, giving the OS a short time to shutdown, then power on.

  • Hard reset—Equivalent to pressing the front panel reset button, or performing an IPMI reset.

  • Shutdown—A graceful shut down of the OS and then power off.

Related Commands

Command

Description

show chassis

 

show psu

 

reboot

To reboot the server, use the reboot command.

reboot

This command has no arguments or keywords.

Command Default

None

Command Modes

CIMC (/cimc)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to reboot the server: 

server# scope cimc
server /cimc # reboot
This operation will reboot the BMC.
Continue?[y|n] y

recover

To recover corrupted BIOS, use the recover command.

recover

This command has no arguments or keywords.

Command Default

None

Command Modes

BIOS (/bios)

Command History

Release Modification
1.1(1)

This command was introduced.

Usage Guidelines

Before executing the recover command, perform the following tasks:


  • Have the BIOS recovery ISO image ready

  • Launch the KVM Console

  • Power off server

  • Map the BIOS recovery ISO image using vMedia

Executing the recover command automatically powers on the server. After the recovery is finished, power cycle or reset the server.

Examples

This example shows how to recover corrupted BIOS: 

server# scope bios
server /bios # recover
This operation will automatically power on the server to perform BIOS FW recovery.
Continue?[y|N]y
server /bios #

Note

You can use the CLI or the KVM console to monitor the progress of the recovery.

Related Commands

Command

Description

show bios

 

show version

 

scope bios

To enter bios mode, use the scope bios command.

scope bios

This command has no arguments or keywords.

Command Default

None

Command Modes

BIOS (/bios)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use bios mode to set the server boot order:


  • CDROM—CD-ROM boot

  • EFI—Extensible Firmware Interface boot

  • FDD—Floppy disk drive boot

  • HDD—Hard disk drive boot

  • PXE—Preboot Execution Environment boot

Examples

This example shows how to enter BIOS mode: 

server# scope bios
server /bios #

Related Commands

Command

Description

show bios

 

show hdd

 

scope certificate

To enter certificate mode, use the scope certificate command.

scope certificate

This command has no arguments or keywords.

Command Default

None

Command Modes

Certificate (/certificate)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use certificate mode to perform the following tasks:


  • Generate a certificate signing request

  • Upload a signed certificate

Examples

This example shows how to enter certificate mode: 

server# scope certificate
server /certificate # ?

Related Commands

Command

Description

show certificate

 

show ssh

 

scope chassis

To enter chassis mode, use the scope chassis command.

scope chassis

This command has no arguments or keywords.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use chassis mode to set the following chassis properties:


  • Server description

  • Server locator LED state

Examples

This example shows how to enter chassis mode: 

server# scope chassis
server /chassis #

Related Commands

Command

Description

show chassis

 

show led

 

scope cimc

To enter cimc (Cisco Integrated Management Controller) mode, use the scope cimc command.

scope cimc

This command has no arguments or keywords.

Command Default

None

Command Modes

CIMC (/cimc)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use cimc mode to perform the following actions:


  • Reset the CIMC to factory default

  • Reboot the CIMC

Examples

This example shows how to enter cimc mode : 

server# scope cimc
server /cimc #

Related Commands

Command

Description

show cimc

 

show log

 

scope fault

To enter fault mode, use the scope fault command.

scope fault

This command has no arguments or keywords.

Command Default

None

Command Modes

Fault (/fault)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use fault mode to set the following SNMP and event properties:


  • SNMP community string

  • Platform event

Examples

This example shows how to enter fault mode : 

server# scope fault
server /fault #

Related Commands

Command

Description

show fault

 

show trap-destination

 

scope http

To enter http mode, use the scope http command.

scope http

This command has no arguments or keywords.

Command Default

None

Command Modes

HTTP (/http)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use http mode to set the following HTTP properties:


  • HTTP enable/disable

  • HTTP port numbers

  • HTTP connection timeout

Examples

This example shows how to enter http mode : 

server# scope http
server /http #

Related Commands

Command

Description

show http

 

show http-port

 

scope ipmi

To enter ipmi (Intelligent Platform Management Interface) mode, use the scope ipmi command.

scope ipmi

This command has no arguments or keywords.

Command Default

None

Command Modes

IPMI (/ipmi)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use ipmi mode to set the following IPMI properties:


  • IPMI enable/disable

  • Encryption key

  • Security privilege level

Examples

This example shows how to enter ipmi mode : 

server# scope ipmi
server /ipmi #

Related Commands

Command

Description

show ipmi

 

show ldap

 

scope kvm

To enter kvm (keyboard, video and mouse) mode, use the scope kvm command.

scope kvm

This command has no arguments or keywords.

Command Default

None

Command Modes

KVM (/kvm)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use kvm mode to set the following KVM properties:


  • Encryption

  • KVM port number

  • Local video

  • Maximum sessions

Examples

This example shows how to enter kvm mode : 

server# scope kvm
server /kvm #

Related Commands

Command

Description

set max-sessions

 

show kvm

 

scope ldap

To enter ldap (Lightweight Directory Access Protocol) mode, use the scope ldap command.

scope ldap

This command has no arguments or keywords.

Command Default

None

Command Modes

LDAP (/ldap)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use ldap mode to set the following LDAP properties:


  • Attribute

  • Base DN (Base Distinguished Name)

  • Encryption

  • LDAP server IP address

  • Timeout

Examples

This example shows how to enter ldap mode : 

server# scope ldap
server /ldap #

Related Commands

Command

Description

set server-ip

 

show ldap

 

scope log

To enter log mode, use the scope log command.

scope log

This command has no arguments or keywords.

Command Default

None

Command Modes

Log (/cimc/log)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use sensor mode to display log entries.

Examples

This example shows how to enter log mode : 

server# scope cimc
server /cimc # scope log
server /cimc/log #

Related Commands

Command

Description

show log

 

show sel

 

scope network

To enter network mode, use the scope network command.

scope network

This command has no arguments or keywords.

Command Default

None

Command Modes

Network (/cimc/network)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use network mode to set the following network and VLAN properties:


  • DHCP

  • DNS

  • IPv4

  • Server VLAN membership

Examples

This example shows how to enter network mode : 

server# scope cimc
server /cimc # scope network
server /cimc/network #

Related Commands

Command

Description

show ipblocking

 

show network

 

set (bios)

To set up the boot order for the server, use the set command in bios mode.

set boot-order boot-order

Syntax Description

boot-order

Specifies setting the server boot order.

boot-order

The server boot order. Use the following boot order arguments, arranging them in the order that you want:


See Usage GuidelinesUsage Guidelines.

Command Default

None

Command Modes

BIOS (/bios)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

Type the boot order arguments using quotes and commas as delimiters. Following is an example:

"EFI","HDD","FDD","CDROM","PXE"

The arguments are not case sensitive.

Examples

This example shows how to set up the boot order for the server: 

server# scope bios
server /bios # set boot-order "EFI","HDD","FDD","CDROM","PXE"
server /bios* # commit
server /bios #

Related Commands

Command

Description

show bios

 

show hdd

 

set (chassis)

To set up the chassis, use the set command in chassis mode.

set { description chassis-description | | locator-led { on | | off } }

Syntax Description

description

Specifies the chassis description.

chassis-description

Description of the chassis. The range of valid values is 1 to 64.

locator-led

Specifies whether the chassis locator LED is on or off.

on

Turns the server locator LED on. See Usage GuidelinesUsage Guidelines.

off

Turns the server locator LED off.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

When you turn on the locator LED, it flashes. This allows you to easily locate the chassis.

Examples

This example shows how to turn on the locator LED: 

server# scope chassis
server /chassis # set locator-led on
server /chassis* # commit
server /chassis #

Related Commands

Command

Description

show chassis

 

show led

 

set (fault)

To set up event management on the server, use the set command in fault mode.

set { community-str community-name | | platform-event-enabled { no | | yes } }

Syntax Description

community-str

Specifies the SNMP community string.

community-name

The name of the SNMP community. A unique set of numbers or letters that identifies the SNMP community. The range of valid values is 1 to 18.

platform-event-enabled

Specifies whether platform event alerts are enabled or disabled.

no

Sets platform event alerts to disabled.

yes

Sets platform event alerts to enabled.

Command Default

None

Command Modes

Fault (/fault)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to set up an SNMP community string: 

server# scope fault
server /fault # set community-str cs100
server /fault* # commit
server /fault #

Related Commands

Command

Description

show fault

 

show trap-destination

 

set (http)

To set up Hyper Text Transfer Protocol (HTTP) services on the server, use the set command in http mode.

set { enabled { no | | yes } | | http-port port-number | | https-port port-number | | timeout time }

Syntax Description

enabled

Specifies whether HTTP services are enabled or disabled.

no

Specifies that HTTP is not enabled.

yes

Specifies that HTTP is enabled.

http-port

Sets the HTTP server port number.

port-number

The HTTP port number of the server . A unique number that identifies the port. The range of valid values is 1 to 65536.

Note   

You also use this argument with the https-port keyword.

https-port

Sets the HTTPS server port number.

timeout

Sets the HTTP connection timeout time.

time

The connection timeout time, in seconds. The range of valid values is 60 to 10800.

Command Default

None

Command Modes

HTTP (/http)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to set the HTTP port number: 

server# scope http
server /http # set http-port 80
server /http* # commit
server /http #

Related Commands

Command

Description

show http-port

 

show https-port

 

set (ipmi)

To set up Intelligent Platform Management Interface (IPMI) on the server, use the set command in ipmi mode.

set { enabled { no | | yes } | | encryption-key encryption-key | | privilege-level { admin | | read-only | | user } }

Syntax Description

enabled

Specifies whether IPMI is enabled or disabled.

no

Specifies that IPMI is not enabled.

yes

Specifies that IPMI is enabled.

encryption-key

Specifies the IPMI encryption key.

encryption-key

The IPMI encryption key. The valid value is 40 hex numbers.

privilege-level

Specifies the IPMI privilege level.

admin

Sets that the IPMI privilege level to admin.

read-only

Sets that the IPMI privilege level to read-only.

user

Sets that the IPMI privilege level to user.

Command Default

None

Command Modes

IPMI (/ipmi)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to set the IPMI encryption key: 

server# scope ipmi
server /ipmi # 
server /ipmi # set encryption-key a9 62 b5 0a 68 6e e3 02 72 ce af f1 39 f8 1e 05 f5 19 d5 e1 7f f4 71 b9 9a 41 be e3 f5 06 4e cc 0f 63 67 2e a2 9c 74 d0
server /ipmi* # commit
server /ipmi #

Related Commands

Command

Description

show ipmi

 

show sol

 

set (kvm)

To set up virtual Keyboard Video Mouse (KVM) functionality on the server, use the set command in kvm mode.

set { enabled { no | | yes } | | encrypted { no | | yes } | | kvm-port port-number | | local- video { no | | yes } | | max-sessions number-of-sessions }

Syntax Description

enabled

Specifies whether KVM is enabled or disabled.

no

Specifies disable. Following are the uses of the no keyword:


  • Specifies that KVM is disabled when used with the enabled keyword.

  • Specifies that encryption is disabled when used with the encrypted keyword.

  • Specifies that local video is disabled when used with thelocal-videocommand.
yes

Specifies enable. Following are the uses of the yes keyword:


  • Specifies that KVM is enabled when used with the enabled command.

  • Specifies that encryption is enabled when used with the encrypted command.

  • Specifies that local video is enabled when used with thelocal-videocommand.
encrypted

Specifies whether KVM is encrypted or not encrypted.

kvm-port

Specifies the KVM port.

port number

The KVM port number. The range of valid values is 1 to 65535.

local-video

Specifies the local video property. See Usage Guidelines Usage Guidelines for more information about using this feature.

max-sessions

Specifies the maximum number of KVM sessions.

number-of-sessions

The maximum number of concurrent KVM sessions. The range of valid values is 1 to 4.

Command Default

None

Command Modes

KVM (/kvm)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

Use the local-video command to display the KVM session on any monitor attached to the server.

Examples

This example shows how to enable KVM: 

server# scope kvm
server /kvm # set kvm enabled
server /kvm* # commit
server /kvm #

Related Commands

Command

Description

show kvm

 

show kvm detail

 

set (ldap)

To set up an LDAP (Lightweight Directory Access Protocol) directory on the server, use the set command in ldap mode.

set { attribute attribute-name | | base-dn base-dn-name | | enabled { no | | yes } | | encrypted { no | | yes } | | server-ip ip-address | | timeout time }

Syntax Description

attribute

Specifies the LDAP attribute. See Usage Guidelines Usage Guidelines for more information about using this feature.

attribute-name

The name of the attribute. See Usage Guidelines Usage Guidelines for more information about using this feature.

base-dn

Specifies the LDAP Base DN. See Usage Guidelines Usage Guidelines for more information about using this feature.

base-dn-name

The Base DN name. A unique set of numbers or letters that identifies the Base DN. The range of valid values is 1 to 63.

enabled

Specifies whether LDAP is enabled or disabled.

no

Specifies disable. Following are the uses of the no keyword:


  • Specifies that LDAP is not enabled for the enabled keyword.

  • Specifies that encryption is not enabled for the encrypted keyword.

yes

Specifies enable. Following are the uses of the yes command:


  • Specifies that LDAP is enabled for the enabled command.

  • Specifies that encryption is enabled for the encrypted command.

encrypted

Specifies whether the Active Directory is encrypted or not encrypted.

server-ip

Specifies the Active Directory server IP address.

ip-address

The IP address. The format is X.X.X.X.

timeout

Specifies the Active Directory server connection timeout.

time

The wait time before a connection timeout, in seconds. The range of valid values is 0 to 1800.

Command Default

None

Command Modes

LDAP (/ldap)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

The attribute stores the values of role and locales for the user.

Base DN is the top level of the LDAP directory tree.

Examples

This example shows how to set the Active Directory server timeout property: 

server# scope ldap
server /ldap # set timeout 100
server /ldap* # commit
server /ldap #

Related Commands

Command

Description

show ldap

 

show ldap detail

 

set (network)

To set up server network services on the server, use the set command in network mode.

set { alternate-dns-server ip-address | | dhcp-enabled { no | | yes } | | dns-use-dhcp | | hostname host-name | | mode { dedicated | | shared-lom | | shipping } | | preferred-dns-server | | redundancy { none | | active-standby } | | v4-addr ip-address | | v4-gateway ip-address | | v4-netmask netmask | | vlan-enabled { no | | yes } | vlan-id vlan-id | | vlan-priority priority-number }

Syntax Description

alternate-dns-server

Specifies the alternate DNS server.

ip-address

The DNS server IP address. You also use this argument with thepreferred-dns-server, v4-addr, and v4-gatewaykeywords. The format is X.X.X.X.

dhcp-enabled

Specifies whether DHCP is enabled or disabled on the server.

no

Specifies disable. Following are the uses of the no keyword:


  • Specifies that DHCP is not enabled when used with the dhcp-enabled keyword.

  • Specifies that VLAN membership is not enabled when used with the vlan-enabled keyword.

yes

Specifies enable. Following are the uses of the yes keyword:


  • Specifies that KVM is enabled when used with the dhcp-enabled command.

  • Specifies that encryption is enabled when used with the vlan-enabled command.

dns-use-dhcp

Specifies the retrieval of DNS addresses via DHCP.

hostname

Specifies the server name.

host-name

The server name. A unique set of numbers or letters that identifies the server. The range of valid values is 1 to 63.

mode

Specifies the server NIC mode.

dedicated

Sets the server network mode to dedicated.

shared-lom

Sets the server network mode to shared LOM.

shipping

Sets the server network mode to shipping.

preferred-dns-server

Specifies the preferred DNS server.

redundancy

Specifies whether redundancy capability is enabled or dsiabled on the server.

none

Sets server redundancy capability to none.

active-standby

Sets server redundancy to active standby failover. See Usage Guidelines Usage Guidelines
v4-addr

Sets the server IPv4 IP address.

v4-gateway

Sets the server IPv4 gateway.

v4-netmask

Sets the server IPv4 netmask.

net-mask

The IPv4 netmask.

vlan-enabled

Specifies whether VLAN membership capability is enabled or disabled on the server.

vlan-id

Sets the VLAN ID.

vlan-id

The identification number of the VLAN. A unique set of numbers or letters that identifies the VLAN.

vlan-priority

Sets the VLAN priority.

priority-number

The priority number of the VLAN.

Command Default

None

Command Modes

Network (/cimc/network)

Command History

Release Modification
1.0(1)

This command was introduced.

1.1(1)

The shipping keyword was introduced.

Usage Guidelines

Active/standby failover lets you use a standby security appliance to take over the functionality of a failed unit. When the active unit fails, it changes to the standby state, while the standby unit changes to the active state. The appliance that becomes active assumes the IP addresses and MAC addresses of the failed unit and begins to pass traffic.

When you use the VLAN commands, you are commiting your server to a membership in a particular VLAN. Following are the advantages of becoming a member of a VLAN:

  • Provides traffic isolation, which leads to enhanced security.

  • Reduces broadcast and multicast traffic, which leads to improved network performance.

Examples

This example shows how to enable DHCP: 

server# scope cimc
server /cimc # scope network
server /cimc/network # set dhcp-enabled yes
server /cimc/network* # commit
server /cimc/network #

Related Commands

Command

Description

show dhcp

 

show network

 

set cli output

To set CLI output on the server, use the set cli output command.

set cli output { default | | yaml }

Syntax Description

cli output

Specifies server CLI output.

default

Sets CLI output to default.

yaml

Sets CLI ouput to YAML (Yet Another Markup Language).

Command Default

None

Command Modes

Any command mode

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to set CLI output to YAML: 

server# set cli output yaml
CLI output format set to yaml
server#

show bios

To display server boot order, use the show bios command in root mode. You can also use the show detail command in BIOS mode to display server boot order.

root mode

show bios [detail]

bios mode

show [detail]

Command Default

None

Command Modes

root (server#)

BIOS (/bios)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

The displayed output of the command shows the boot order of the following available boot devices:


  • CDROM—Bootable CD-ROM

  • FDD—Floppy disk drive

  • HDD—Hard disk drive

  • PXE—PXE boot

  • EFI—Extensible Firmware Interface

Examples

This example shows how to display the server boot order: 

server# show bios
Boot Order                   
---------------------------- 
CDROM,HDD,PXE,EFI,FDD

Related Commands

Command

Description

show hdd

 

 

show certificate

To display server certificate information, use the show certificate command in root mode. You can also use the show detail command in certificate mode to display server certificate information.

root mode

show certificate [detail]

certificate mode

show [detail]

Syntax Description

detail

(Optional) Displays detailed server certificate information in list form.

Command Default

None

Command Modes

root (server#)

Certificate (/certificate)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to display server certificate information:

server# show certificate
Serial Number    Valid From               Valid To                 
---------------- ------------------------ ------------------------ 
001              Apr 13 13:49:00 2009 GMT Apr 11 13:49:00 2019 GMT

Related Commands

Command

Description

set ssh-port

 

show ssh

 

show chassis

To display chassis information, use the show chassis command in root mode. You can also use the show detail command in chassis mode to display chassis information.

root mode

show chassis [detail]

chassis mode

show [detail]

Syntax Description

detail

(Optional) Displays detailed chassis information in list form.

Command Default

None

Command Modes

root (server#)

Chassis (/chassis)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to display chassis information:

Server# show chassis
Power Serial Number Product Name  UUID                                 
----- ------------- ------------- ------------------------------------ 
on    QTF-0934-00   R100-1120402  208F4277020FBADBADBEA80000DEAD00

Related Commands

Command

Description

show cpu

 

show hdd

 

show cimc

To display CIMC information, use the show cimc command in root mode. You can also use the show detail command in CIMC mode to display CIMC information.

root mode

show cimc [detail]

cimc mode

show [detail]

Syntax Description

detail

(Optional) Displays detailed CIMC information in list form.

Command Default

None

Command Modes

root (server#)

CIMC (/cimc)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to display CIMC information:

Server# show cimc
Firmware Version     Current Time             
-------------------- ------------------------ 
1.0(0.86)            Fri Oct  2 12:19:17 2009

Related Commands

Command

Description

show firmware

 

show log

 

show fault

To display fault information, use the show fault command in root mode. You can also use the show detail command in fault mode to display fault information.

root mode

show fault [detail]

fault mode

show [detail]

This command has no arguments or keywords.

Command Default

None

Command Modes

Fault (/fault)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to display fault information: 

server# show fault

SNMP Community String Platform Event Enabled
--------------------- ----------------------
33West                yes                     
34West                no                     

server#

Related Commands

Command

Description

show pef

 

show trap-destination

 

show firmware

To display firmware information, use the show firmware command in CIMC mode. You can also use the show detail command in firmware mode to display firmware information.

cimc mode

show firmware [detail]

firmware mode

show [detail]

Syntax Description

detail

(Optional) Displays detailed firmware information in list form.

Command Default

None

Command Modes

CIMC (/cimc)

firmware (/cimc/firmware)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to display firmware information:

server# scope cimc
Server /cimc # show firmware
Update Stage Update Progress Current FW Version 
------------ --------------- ------------------ 
NONE         100             1.0(0.86)          

server /cimc # show firmware detail
Firmware Image Information:
    Update Stage: NONE
    Update Progress: 100
    Current FW Version: 1.0(0.86)
    FW Image 1 Version: 1.0(0.86)
    FW Image 1 State: RUNNING ACTIVATED
    FW Image 2 Version: 1.0(0.74)
    FW Image 2 State: BACKUP INACTIVATED

Server /cimc #

Related Commands

Command

Description

show cimc

 

show version

 

show http

To display information about HTTP services, use the show http command in root mode. You can also use the show detail command in HTTP mode to display HTTP services information.

root mode

show http [detail]

http mode

show [detail ]

Syntax Description

detail

(Optional) Displays detailed HTTP services information in list form.

Command Default

None

Command Modes

root (server#)

HTTP (/http)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to display information about HTTP services: 

Server# show http
HTTP Port  HTTPS Port Timeout  Active Sessions Enabled
---------- ---------- -------- --------------- ------- 
80         443        1800     0               yes     
Server#

Related Commands

Command

Description

set http-port

 

set https-port

 

top

To return to root mode from any mode, use the top command.

top

This command has no arguments or keywords.

Command Default

None

Command Modes

Any command mode

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to enter root mode from any mode: 

server /cimc/log # top
server#