Cisco UCS C-Series Servers Integrated Management Controller CLI Command Reference, Release 1.5

activate (firmware)

To activate CIMC firmware, use the activate command.

activate

This command has no arguments or keywords.

Command Default

None

Command Modes

Firmware (/cimc/firmware)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to activate CIMC firmware:

server# scope cimc
server /cimc # scope firmware
server /cimc/firmware # activate
server /cimc/firmware #

Related Commands

Command	Description
show cimc
show version

activate-adapter-fw

To activate an adapter firmware image, use the activate-adapter-fw command.

activate-adapter-fw pci-slot image

Syntax Description

pci-slot	The PCI slot number of the adapter card.
image	The number of the firmware image to be activated. This can be the number 1 or 2.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.2(1)	This command was introduced.

Usage Guidelines

Use this command to select one of two adapter firmware images to be activated upon the next reboot of the server. Use the show adapter detail command to view the status and version information of the installed firmware images.

Examples

This example shows how to activate firmware image 2 in the adapter in PCI slot 1:

Server# scope chassis
Server /chassis # activate-adapter-fw 1 2 
Firmware image activation succeeded
Please reset the server to run the activated image
Server /chassis #

Related Commands

Command	Description
show adapter detail

adapter-reset

To reset the adapter, use the adapter-reset command.

Note

Resetting the adapter also resets the host.

adapter-reset index

Syntax Description

index

The PCI slot number of the adapter to be reset.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.4(6)	This command was introduced.

Usage Guidelines

Use this command to reset the adapter at the PCI slot number specified by the index argument.

Examples

This example shows how to reset the adapter in PCI slot 1:

Server# scope chassis
Server /chassis # adapter-reset 1
This operation will reset the adapter and the host if it is on.
You may lose connectivity to the CIMC and may have to log in again.
Continue?[y|N] y
Server /chassis #

Related Commands

Command	Description
show adapter detail

adapter-reset-defaults

To reset the adapter to default setting, use the adapter-reset-defaults command.

adapter-reset-defaults index

Syntax Description

index

The PCI slot number of the adapter to be reset to factory default settings.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.2(1)	This command was introduced.

Usage Guidelines

Use this command to restore factory default settings for the adapter at the PCI slot number specified by the index argument.

Examples

This example shows how to reset the adapter in PCI slot 1 to its default setting:

Server# scope chassis
Server /chassis # adapter-reset-defaults 1
This operation will reset the adapter to factory default.
All your configuration will be lost.
Continue?[y|N] y
Server /chassis #

Related Commands

Command	Description
show adapter detail

bios-setup-defaults

To restore the BIOS settings to default values, use the bios-setup-defaults command.

bios-setup-defaults

This command has no arguments or keywords.

Command Default

None

Command Modes

BIOS (/bios)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to restore the BIOS settings to default values. This command initiates a reboot.

Examples

This example shows how to restore the BIOS settings to default values:

Server# scope bios
Server /bios # bios-setup-default
This operation will reset the BIOS set-up tokens to factory defaults.
All your configuration will be lost.
Changes to BIOS set-up parameters will initiate a reboot.
Continue?[y|N]y

Related Commands

Command	Description
show bios

cancel

To stop the technical support process, use the cancel command.

cancel

This command has no arguments or keywords.

Command Default

None

Command Modes

Technical support (/cimc/tech-support)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to stop the technical support process:

server # scope cimc
server /cimc # scope tech-support
server /cimc/tech-support # cancel 
This operation will cancel your current Tech Support upload.
Continue?[y|N]y
server /cimc/tech-support #

Related Commands

Command	Description
start

cancel-initialization

To cancel the initialization of a virtual drive, use the cancel-initialization command.

cancel-initialization

This command has no arguments or keywords.

Command Default

None

Command Modes

Virtual drive (/chassis/storageadapter/virtual-drive)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must be logged in as an admin to use this command.

Examples

This example shows how to cancel the initialization of virtual drive 3:

Server # scope chassis
Server /chassis # scope storageadapter SLOT-3
Server /chassis/storageadapter # scope virtual-drive 3
Server /chassis/storageadapter/virtual-drive # start-initialization
Are you sure you want to initialize virtual drive 3?
All data on the drive will be lost. Enter 'yes' to confirm. yes
Fast (0) or full (1) initialization? 0
Server /chassis/storageadapter/virtual-drive # cancel-initialization
Are you sure you want to cancel the initialization of virtual drive 3?
Enter 'yes' to confirm -> yes
Server /chassis/storageadapter/virtual-drive #

carve-virtual-drive

To create a virtual drive from an existing drive group, use the carve-virtual-drive command.

carve-virtual-drive

This command has no arguments or keywords.

Command Default

None

Command Modes

Storage Adapter (/chassis/storageadapter)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

None

Examples

This example shows how to create a new virtual drive from unused space in an existing drive group:

Server# scope chassis
Server /chassis # scope storageadapter SLOT-3
Server /chassis/storageadapter # carve-virtual-drive
  < Fetching virtual drives...>

ID  Name              RL  VDSize        MaxPossibleSize PD(s)
----------------------------------------------------------------
 3  test_v_drive      1   1000 MB       67664 MB        6,7

Please choose from the above list the virtual drive number
whose space the new virtual drive will share--> 3
New virtual drive will share space with VD 3

Please enter Virtual Drive name (15 characters maximum)--> new_from_test
Please enter Virtual Drive size in MB, GB, or TB (maximum: 67664 MB)
  Example format: '400 GB' --> 500 MB

Optional attribute:
  Write Policy: defaults to Write Back
    OK? (y or n)--> y

New virtual drive will have the following characteristics:
  - It will share space with virtual drive 3
  - Name: 'new_from_test'
  - Size: 500 MB

OK? (y or n)--> y
Server /chassis/storageadapter # show virtual-drive
Virtual Drive Health         Status               Name             Size       RAID Level Boot Drive
------------- -------------- -------------------- ---------------- ---------- ---------- ----------
0             Good           Optimal                               150528 MB  RAID 0     false
1             Good           Optimal                               20480 MB   RAID 0     true
2             Good           Optimal                               114140 MB  RAID 0     false
3             Good           Optimal              test_v_drive     1000 MB    RAID 1     false
4             Good           Optimal              new_from_test    500 MB     RAID 1     false

Server /chassis/storageadapter #

clear (log)

To clear the CIMC log, use the clear command in log mode.

clear

This command has no arguments or keywords.

Command Default

None

Command Modes

Log (/cimc/log)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to clear the CIMC log:

server# scope cimc
server /cimc # scope log
server /cimc/log # clear
server /cimc/log #

Related Commands

Command	Description
show sel
show sensor

clear (sel)

To clear the system event log, use the clear command in sel mode.

clear

This command has no arguments or keywords.

Command Default

None

Command Modes

System event log (/sel)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to clear the system event log:

server# scope sel
server /sel # clear
server /sel #

Related Commands

Command	Description
show sel
show sensor

clear-cmos

To clear the BIOS settings in CMOS memory, use the clear-cmos command.

clear-cmos

This command has no arguments or keywords.

Command Default

None

Command Modes

BIOS (/bios)

Command History

Release	Modification
1.1(1)	This command was introduced.

Examples

This example shows how to clear the BIOS settings in CMOS memory:

server# scope bios
server /bios # clear-cmos

This operation will clear the BIOS CMOS.
Note: Server should be in powered off state to clear CMOS.
Continue?[y|n] y

server /bios #

Related Commands

Command	Description
show bios

clear-foreign-config

To clear all foreign configuration on the controller, use the clear-foreign-config command.

clear-foreign-config

This command has no arguments or keywords.

Command Default

None

Command Modes

Storage adapter (/chassis/storageadapter)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must be logged in as an admin to use this command.

When you run this command, all foreign configuration and all configuration information from all physical drives hosting foreign configuration is deleted. This action cannot be reverted.

Examples

This example shows how to clear all foreign configurations on the MegaRAID controller in slot 3:

Server # scope chassis
Server /chassis # scope storageadapter SLOT-3
Server /chassis/storageadapter # clear-foreign-config
Are you sure you want to clear all foreign configurations on this controller?
All data on the drive(s) will be lost.
Enter 'yes' to confirm -> yes
Server /chassis/storageadapter #

commit

To save configuration changes, use the commit command.

commit

This command has no arguments or keywords.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to save a configuration change:

server /http # set enabled yes
server /http* # commit
server http #

Related Commands

Command	Description
discard

configure-vmfex

To specify the number of VM FEX interfaces you want CIMC to create, use the configure-vmfex command.

configure-vmfex port-count

Syntax Description

port-count

The number of VM FEX interfaces to create.

Command Default

None

Command Modes

Adapter (/chassis/adapter)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to specify the number of virtual machine fabric extender (VM FEX) interfaces you want CIMC to create. The range is 0 to 112. NIV mode must be enabled.

Examples

This example shows how to specify that 24 VM FEX interfaces are created:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # set niv-mode enable
Server /chassis/adapter *# configure-vmfex 24
Server /chassis/adapter *# commit
Server /chassis/adapter #

Related Commands

Command	Description
scope vmfex

connect

To connect to either the server CLI or the server shell, use the connect command.

connect { host | shell }

Syntax Description

host	Specifies the CLI on the server.
shell	Specifies the GNU bash shell on the server.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use the exit command to exit the GNU bash shell.

Examples

This example shows how to connect to the server shell:

server# connect shell
bash-3.2

Related Commands

Command	Description
exit

create-boot-entry

To create a boot entry in the host Fibre Channel interface, use the create-boot-entry command.

create-boot-entry wwpn lun-id

Syntax Description

wwpn	The World Wide Port Name (WWPN) for the boot target.
lun-id	The LUN ID of the boot LUN.

Command Default

None

Command Modes

Fibre Channel host interface (/chassis/adapter/host-fc-if)

Command History

Release	Modification
1.2(1)	This command was introduced.

Usage Guidelines

Use this command to create boot entry. The range of the lun-id is 0 to 255. The wwpn for the boot target should be in the form hh:hh:hh:hh:hh:hh:hh:hh.

Examples

This example shows how to create a boot entry in the host Fibre Channel interface:

Server# scope chassis 
Server /chassis # scope adapter 1 
Server /chassis/adapter # scope host-fc-if fc1 
Server /chassis/adapter/host-fc-if # create-boot-entry 20:00:00:11:22:33:44:55 3 
Server /chassis/adapter/host-fc-if *# commit 
New boot table entry will take effect upon the next server reset 
Server /chassis/adapter/host-fc-if #

Related Commands

Command	Description
delete boot

create host-eth-if

To create a virtual Ethernet interface, use the create host-eth-if command.

create host-eth-if name

Syntax Description

name	The name of the vNIC.

Command Default

None

Command Modes

Adapter (/chassis/adapter)

Command History

Release	Modification
1.2(1)	This command was introduced.

Usage Guidelines

Use this command to create the virtual host Ethernet network interface card (vNIC). The name argument can be up to 32 ASCII characters.

Examples

This example shows how to create a vNIC:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # create host-eth-if Vnic5
Server /chassis/adapter/host-eth-if* # commit
New host-eth-if settings will take effect upon the next server reset
Server /chassis/adapter/host-eth-if #

Related Commands

Command	Description
delete host-eth-if

create host-fc-if

To create a virtual host bus adapter (vHBA), use the create host-fc-if command.

create host-fc-if name

Syntax Description

name	The name of the vHBA.

Command Default

None

Command Modes

Adapter (/chassis/adapter)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to create the virtual Fibre Channel host bus adapter (vHBA). The name argument can be up to 32 ASCII characters.

Examples

This example shows how to create a vHBA:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # create host-fc-if Vhba5
Server /chassis/adapter/host-fc-if* # commit
New host-fc-if settings will take effect upon the next server reset
Server /chassis/adapter/host-fc-if #

Related Commands

Command	Description
delete host-fc-if

create-virtual-drive

To create a virtual drive from unused physical drives, use the create-virtual-drive command.

create-virtual-drive

This command has no arguments or keywords.

Command Default

None

Command Modes

Storage Adapter (/chassis/storageadapter)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must be logged in as an admin to use this command.

Examples

This example shows how to create a new virtual drive that spans two unused physical drives:

Server# scope chassis
Server /chassis # scope storageadapter SLOT-3
Server /chassis/storageadapter # create-virtual-drive
Please enter RAID level
(0, 1, 5, 6, 10, 50, 60) --> 1

Please choose from the following 2 unused physical drives:
    Slot 6: size 68664 MB
    Slot 7: size 68664 MB

Specify physical disks for span 0:
  Enter comma-separated PDs from above list--> 6,7
Please enter Virtual Drive name (15 characters maximum)--> test_v_drive
Please enter Virtual Drive size in MB, GB, or TB
Example format: '400 GB' --> 1000 MB

Optional attribute:
  Write Policy: defaults to Write Back 
    OK? (y or n)--> n
    0: Write Through
    1: Write Back
    2: Write Back with Bad BBU
    3: Write Back Adaptive
  Choose number from above options--> 2

Write Policy will be set to Write Back with Bad BBU (2 and 'write-policy\:2')

New virtual drive will have the following characteristics:
  - Spans: '[6.7]'
  - RAID level: '1'
  - Name: 'test_v_drive'
  - Size: 1000 MB
  - Write Policy: Write Back with Bad BBU
OK? (y or n)--> y

Server /chassis/storageadapter # show virtual-drive
Virtual Drive Health         Status               Name             Size       RAID Level Boot Drive
------------- -------------- -------------------- ---------------- ---------- ---------- ----------
0             Good           Optimal                               150528 MB  RAID 0     false
1             Good           Optimal                               20480 MB   RAID 0     true
2             Good           Optimal                               114140 MB  RAID 0     false
3             Good           Optimal              test_v_drive     1000 MB    RAID 1     false
4             Good           Optimal              new_from_test    500 MB     RAID 1     false

Server /chassis/storageadapter #

create iscsi-boot

To create an iSCSI boot target for a vNIC, use the create iscsi-boot command.

create iscsi-boot index

Syntax Description

index

The index of the iSCSI boot for a vNIC. Enter 0 as the index value.

Command Default

None

Command Modes

Host Ethernet Interface (/chassis/adapter/host-eth-if)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

To configure a vNIC as iSCSI-bootable, you must enable the PXE Boot option for the vNIC.

Examples

This example shows how to create an iSCSI boot index for a vNIC:

Server # scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # create iscsi-boot 0
Server /adapter/host-eth-if/iscsi-boot *# commit

New host-eth-if settings will take effect upon the next server reset

Server /adapter/host-eth-if/iscsi-boot #

Related Commands

Command	Description
scope iscsi-boot
create iscsi-target

create iscsi-target

To create an iSCSI target for a vNIC, use the create iscsi-target command.

create iscsi-target index

Syntax Description

index

The index of the iSCSI target. It can be either 0 or 1.

Command Default

None

Command Modes

iSCSI boot (/chassis/adapter/host-eth-if/iscsi-boot)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

To configure a vNIC as iSCSI-bootable, you must enable the PXE Boot option for the vNIC.

You must be logged in as an admin to perform this task.

Examples

This example shows how to create an iSCSI target for a vNIC:

Server # scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # create iscsi-boot 0
Server /adapter/host-eth-if/iscsi-boot* # create iscsi-target 0
Server /adapter/host-eth-if/iscsi-boot/iscsi-target *# set iqn.2012-01.com.asdcs:abcde
Server /adapter/host-eth-if/iscsi-boot/iscsi-target *# set ipaddr 1.2.3.4
Server /adapter/host-eth-if/iscsi-boot/iscsi-target *# commit

New host-eth-if settings will take effect upon the next server reset

Server /adapter/host-eth-if/iscsi-boot/iscsi-target #

delete boot

To delete a boot entry, use the delete boot command.

delete boot entry

Syntax Description

entry

The boot table entry.

Command Default

None

Command Modes

Fibre Channel host interface (/chassis/adapter/host-fc-if)

Command History

Release	Modification
1.2(1)	This command was introduced.

Usage Guidelines

Use this command to delete the boot table entry at the specified position. The range of entry is 0 to 3. The change takes effect upon the next server reset.

Examples

This example shows how to delete a boot entry in the host Fibre Channel interface:

Server# scope chassis 
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc1
Server /chassis/adapter/host-fc-if # show boot
Boot Table Entry Boot Target WWPN Boot LUN ID
----------------- -------------------------- ------------
0 20:00:00:11:22:33:44:55 3
1 20:00:00:11:22:33:44:56 5
Server /chassis/adapter/host-fc-if # delete boot 1
Server /chassis/adapter/host-fc-if *# commit
New host-fc-if settings will take effect upon the next server reset
Server /chassis/adapter/host-fc-if # show boot
Boot Table Entry Boot Target WWPN Boot LUN ID
----------------- -------------------------- ------------
0 20:00:00:11:22:33:44:55 3
Server /chassis/adapter/host-fc-if #

Related Commands

Command	Description
create-boot-entry
show-boot

delete host-eth-if

To delete an Ethernet interface, use the delete host-eth-if command.

delete host-eth-if name

Syntax Description

name	The name of the vNIC.

Command Default

None

Command Modes

Adapter (/chassis/adapter)

Command History

Release	Modification
1.2(1)	This command was introduced.

Usage Guidelines

Use this command to delete the specified virtual host Ethernet network interface card (vNIC). You cannot delete either of the two default vNICs, eth0 or eth1.

Examples

This example shows how to delete a vNIC:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # delete host-eth-if Vnic5
Server /chassis/adapter *# commit
New host-eth-if settings will take effect upon the next server reset
Server /chassis/adapter #

Related Commands

Command	Description
create host-eth-if

delete host-fc-if

To delete a vHBA interface, use the delete host-fc-if command.

delete host-fc-if name

Syntax Description

name	The name of the vHBA.

Command Default

None

Command Modes

Adapter (/chassis/adapter)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to delete the specified virtual Fibre Channel host bus adapter (vHBA). You cannot delete either of the two default vHBAs, fc0 or fc1.

Examples

This example shows how to delete a vHBA:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # delete host-fc-if Vhba5
Server /chassis/adapter *# commit
New host-fc-if settings will take effect upon the next server reset
Server /chassis/adapter #

Related Commands

Command	Description
create host-fc-if

delete-virtual-drive

To delete a virtual drive, use the delete-virtual-drive command.

delete-virtual-drive

This command has no arguments or keywords.

Command Default

None

Command Modes

Virtual drive (/chassis/storageadapter/virtual-drive)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must be logged in as an admin to use this command.

This command deletes a virtual drive, including the drives that run the booted operating system. So back up any data that you want to retain before you delete a virtual drive.

Examples

This example shows you how to delete virtual drive 3:

Server# scope chassis
Server /chassis # scope storageadapter SLOT-3
Server /chassis/storageadapter # scope virtual-drive 3
Server /chassis/storageadapter/virtual-drive # delete-virtual-drive
Are you sure you want to delete virtual drive 3?
All data on the drive will be lost.  Enter 'yes' to confirm -> yes
Server /chassis/storageadapter/virtual-drive #

delete iscsi-boot

To delete the iSCSI boot configuration for a vNIC, use the delete iscsi-boot command.

delete iscsi-boot index

Syntax Description

0	The index of the iSCSI boot configuration on the vNIC.

Command Default

None

Command Modes

Host Ethernet Interface (/chassis/adapter/host-eth-if)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must be logged in as an admin to perform this task.

This command will erase the iSCSI boot configuration completely from the vNIC.

Examples

This example shows how to erase the iSCSI boot configuration from a vNIC:

Server # scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # delete iscsi-boot 0
Server /adapter/host-eth-if *# commit

New host-eth-if settings will take effect upon the next server reset

Server /adapter/host-eth-if #

Related Commands

Command	Description
create iscsi-boot
create iscsi-target
scope iscsi-boot

delete iscsi-target

To delete an iSCSI target, use the delete iscsi-target command.

delete iscsi-target index

Syntax Description

index

The index of the iSCSI target. It can be either 0 or 1.

Command Default

None

Command Modes

iSCSI boot (/chassis/adapter/host-eth-if/iscsi-boot)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

An iSCSI target must be created to use this command.

You must be logged in as an admin to perform this task.

Examples

This example shows how to delete an iSCSI target for a vNIC:

Server # scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # scope iscsi-boot 0
Server /adapter/host-eth-if/iscsi-boot # delete iscsi-target 0
Server /adapter/host-eth-if/iscsi-boot/iscsi-target *# commit
Server /adapter/host-eth-if/iscsi-boot/iscsi-target #

delete virtual-drive

To delete a virtual drive, use the delete virtual-drive command.

delete virtual-drive drive-number

Syntax Description

drive-number

The drive number.

Command Default

None

Command Modes

Storage Adapter (/chassis/storageadapter)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must be logged in as an admin to use this command.

Deleting a virtual drive removes all active virtual drives, including those that run the operating system. So back up any data that you want to retain before you delete a virtual drive.

Examples

This example shows how to delete virtual drive 3.

Server# scope chassis
Server /chassis # scope storageadapter SLOT-3
Server /chassis/storageadapter # scope virtual-drive 3
Server /chassis/storageadapter/virtual-drive # delete-virtual-drive
Are you sure you want to delete virtual drive 3?
All data on the drive will be lost.  Enter 'yes' to confirm -> yes
Server /chassis/storageadapter/virtual-drive #

disable-auto-learn

To disable the battery auto-learn cycles, use the disable-auto-learn command.

disable-auto-learn

This command has no arguments or keywords.

Command Default

None

Command Modes

Battery Backup Unit (/chassis/storageadapter/bbu)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must be logged in as an admin to use this command.

Examples

This example shows how to disable the battery auto-learn cycles:

Server # scope chassis
Server /chassis # scope storageadapter SLOT-2
Server /chassis/storageadapter # scope bbu
Server /chassis/storageadapter/bbu # disable-auto-learn
Automatic BBU learn cycles will no longer occur if disabled.

Are you sure? [y/n] --> y
disable-auto-learn initiated

Server /chassis/storageadapter/bbu #

Related Commands

Command	Description
enable-auto-learn
start-learn-cycle

discard

To discard all configurations, use the discardcommand.

discard

This command has no arguments or keywords.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to discard all configurations:

server# discard
server#

Related Commands

Command	Description
show pending

enable-auto-learn

To enable the battery auto learn cycles, use the enable-auto-learn command.

enable-auto-learn

This command has no arguments or keywords.

Command Default

None

Command Modes

Battery Backup Unit (/chassis/storageadapter/bbu)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must be logged in as an admin to use this command.

Examples

This example shows how to enable the battery auto-learn cycles:

Server # scope chassis
Server /chassis # scope storageadapter SLOT-2
Server /chassis/storageadapter # scope bbu
Server /chassis/storageadapter/bbu # enable-auto-learn
Automatic BBU learn cycles will occur without notice if enabled.
Are you sure? [y/n] --> y
enable-auto-learn initiated
Server /chassis/storageadapter/bbu #

Related Commands

Command	Description
disable-auto-learn
start-learn-cycle

exit

To leave any command mode, use the exit command.

exit

This command has no arguments or keywords.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to exit BIOS command mode:

server /bios # exit
server#

Related Commands

Command	Description
scope
enter

export-config

To export a CIMC configuration to a remote server, use the export-config command.

export-config protocol ip-address path-and-filename

Syntax Description

protocol	Specifies the protocol to connect to the remote server. It can be one of the following: TFTP FTP SFTP SCP HTTP
ip-address	The IP address of a remote server hosting the CIMC configuration file.
path-and-filename	Specifies the absolute path to the file on the remote server.

Command Default

None

Command Modes

Import-export (/cimc/import-export)

Command History

Release	Modification
1.1(2)	This command was introduced.
1.5(1)	This command was modified to support new remote server protocols.

Usage Guidelines

Use this command to export the CIMC configuration as a file. The path-and-filename is a unique set of up to 128 characters that identifies the path and CIMC configuration filename on the remote server. Do not use characters that are not allowed in a URL.

To determine whether the export operation has completed successfully, use the show detail command. To abort the operation, press CTRL+C.

Note

For security reasons, this operation does not export user accounts or the server certificate.

Examples

This example shows how to export a CIMC configuration to a remote TFTP server:

server# scope cimc
server /cimc # scope import-export
server /cimc/import-export # export-config tftp  se192.0.2.34 /ucs/backups/cimc5.xml
Export config started. Please check the status using "show detail".

server /cimc/import-export # show detail
Export Export:
    Operation: EXPORT
    Status: COMPLETED
    Error Code: 100 (No Error)
    Diagnostic Message: NONE

server /cimc/import-export #

Related Commands

Command	Description
import-config

export-vnic

To export the adapter vNIC configuration, use the export-vnic command.

export-vnic protocol remote server IP address path

Syntax Description

protocol

Protocol to be used to export the configuration. It can be one of the following:

TFTP
FTP
SFTP
SCP
HTTP

remote server IP address

IP/DNS address of the remote server.

path

The absolute path to the file on the remote server along with the name of the adapter configuration file to be exported.

Command Default

None

Command Modes

Adapter (/chassis/adapter)

Command History

Release	Modification
1.2(1)	This command was introduced.
1.5(1)	This command was modified to support additional protocols.

Usage Guidelines

Use this command to export the adapter vNIC configuration. The adapter configuration file is stored at the specified path and filename on the remote server at the specified IP address.

Examples

This example shows how to export the adapter vNIC configuration:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # export-vnic tftp 192.0.2.34 /backup/P81E.cfg
Server /chassis/adapter #

Related Commands

Command	Description
import-vnic

factory-default (cimc)

To set the server to factory default, use the factory-default command.

factory-default

This command has no arguments or keywords.

Command Default

None

Command Modes

Cisco Integrated Manangement Controller (/cimc)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to set the server to factory default:

server# scope cimc
server /cimc # factory-default
This operation will reset the CIMC configuration to factory default.
All your configuration will be lost.
Continue?[y|N] y

get-operation-progress

To view the status of the current task running on a physical drive or a virtual drive, use the get-operation-progress command.

get-operation-progress

This command has no arguments or keywords.

Command Default

None

Command Modes

Physical drive (/chassis/storageadapter/physical-drive)

Virtual drive (/chassis/storageadapter/virtual-drive)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must be logged in as an admin to use this command.

Examples

This example shows how to view the status of the current task running on a physical drive:

Server # scope chassis
Server /chassis # scope storageadapter SLOT-3
Server /chassis/storageadapter # scope virtual-drive 3
Server /chassis/storageadapter/virtual-drive # start-initialization
Are you sure you want to initialize virtual drive 3?
All data on the drive will be lost.
Enter 'yes' to confirm. --> yes
Fast (0) or full (1) initialization? -> 1
Server /chassis/storageadapter/virtual-drive # get-operation-progress 

progress-percent: 15
elapsed-seconds: 23
operation-in-progress: Foreground initialization in progress

Server /chassis/storageadapter #

generate-csr (certificate)

To generate a Certificate Request Signing (CSR), use the generate-csr command.

generate csr

This command has no arguments or keywords.

Command Default

None

Command Modes

Certificate (/certificate)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to generate a CSR :

server# scope certificate
server /certificate # generate-csr

Common Name (CN): abcCertificate
Organization Name (O): abcCo
Organization Unit (OU): 01
Locality (L): west
StateName (S): CA
Country Code (CC): US
Email: abcCo@abcCo.com
Continue to generate CSR?[y|N] y

-----BEGIN CERTIFICATE REQUEST-----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-----END CERTIFICATE REQUEST-----

server /certificate #

Related Commands

Command	Description
show certificate
show ssh

generate-nmi

To generate a Non maskable Interrupt (NMI) signal for a server and to send it to the host, use the generate-nmi command.

generate-nmi

This command has no keywords or arguments.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

This command creates crash dump files when a server hangs and does not respond to traditional debugging methods.

Using this command might restart the OS.

To use this command, the server must be powered on, and you must be logged in as an administrator.

Examples

This example shows how to generate NMI signals for a server:

Server # scope chassis
Server /chassis # generate-nmi
This operation will send NMI to the host and may cause reboot of the OS. 
OS reboot depends on it's NMI configuration.
Do you want to continue? [y|N] y
Server /chassis #

import-config

To import a CIMC configuration, use the import-config command.

import-config protocol ip-address path-and-filename

Syntax Description

protocol	Specifies the protocol to connect to the remote server. It can be one of the following: TFTP FTP SFTP SCP HTTP
ip-address	The IP address of a remote server hosting the CIMC configuration file.
path-and-filename	Specifies the absolute path to the file on the remote server.

Command Default

None

Command Modes

Import-export (/cimc/import-export)

Command History

Release	Modification
1.1(2)	This command was introduced.
1.5(1)	This command was modified to support new remote server protocols.

Usage Guidelines

Use this command to import a CIMC configuration file. The path-and-filename is a unique set of up to 128 characters that identifies the path and CIMC configuration file name on the remote server. Do not use characters that are not allowed in a URL.

To determine whether the import operation has completed successfully, use the show detail command. To abort the operation, press CTRL+C.

Note

Some modifications caused by an import operation, such as IP address changes, can disrupt traffic or cause a server reboot.

Examples

This example shows how to import a CIMC configuration from a remote TFTP server:

server# scope cimc
server /cimc # scope import-export
server /cimc/import-export # import-config tftp 192.0.2.34 /ucs/backups/cimc5.xml
Import config started. Please check the status using "show detail".

server /cimc/import-export #

Related Commands

Command	Description
export-config

import-vnic

To import the adapter vNIC configuration, use the import-vnic command.

import-vnic protocol remote server IP address path

Syntax Description

protocol

Protocol to be used to import the configuration. It can be one of the following:

TFTP
FTP
SFTP
SCP
HTTP

remote server IP address

IP/DNS address of the remote server.

path

The absolute path to the file on the remote server along with the name of the adapter configuration file to be imported.

Command Default

None

Command Modes

Adapter (/chassis/adapter)

Command History

Release	Modification
1.2(1)	This command was introduced.
1.5(1)	This command was modified to support additional protocols.

Usage Guidelines

Use this command to import the adapter vNIC configuration. The adapter downloads and installs the configuration from the specified path and filename on the remote server at the specified IP address.

Examples

This example shows how to import the adapter vNIC configuration:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # import-vnic tftp 192.0.2.34 /backup/P81E.cfg
Server /chassis/adapter #

Related Commands

Command	Description
export-vnic

locateHDD

To turn on or off a hard disk drive (HDD) locator LED, use the locateHDD command.

locateHDD drivenum { 1 | 2 }

Syntax Description

drivenum	The HDD number.
{1 \| 2}	A value of 1 turns the LED on; a value of 2 turns the LED off.

Command Default

None

Command Modes

HDD (/chassis/hdd)

Command History

Release	Modification
1.4(5)	This command was introduced.

Examples

This example turns on the locator LED on HDD 2:

Server# scope chassis
Server /chassis # scope hdd
Server /chassis/hdd # locateHDD 2 1
HDD Locate LED Status changed to 1
Server /chassis/hdd # show
Name                 Status               LocateLEDStatus      
-------------------- -------------------- -------------------- 
HDD1_STATUS          present              TurnOFF              
HDD2_STATUS          present              TurnON              
HDD3_STATUS          absent               TurnOFF              
HDD4_STATUS          absent               TurnOFF              

Server /chassis/hdd #

Related Commands

Command	Description
show hdd

locator-led

To turn on or off the locator LED for the battery, use the locator-led command.

locator-led ON OFF

Syntax Description

ON	Turns on the LED locator.
OFF	Turns off the LED locator.

Command Default

None

Command Modes

Physical drive (/chassis/storageadapter/physical-drive)

Command History

Release	Modification
1.4(1)	This command was introduced in the physical drive command mode.

Usage Guidelines

Use this command to turn on or off the locator LED for a physical drive.

Examples

This example shows how to turn on the locator LED for a physical drive:

server# scope chassis
server /chassis # scope storageadapter SLOT-3
Server /chassis/storageadapter # scope physical-drive 3
Server /chassis/storageadapter/physical-drive # set locator-led on
server /chassis/storageadapter/physical-drive* # commit
server /chassis/storageadapter/physical-drive #

make-dedicated-hot-spare

To specify a physical drive as a dedicated hot spare for a specific virtual drive, use the make-dedicated-hot-spare command.

make-dedicated-hot-spare virtual-drive

Syntax Description

virtual-drive

Number of the virtual drive.

Command Default

None

Command Modes

Physical drive (/chassis/storageadapter/physical-drive)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must be logged in as an admin to use this command.

Examples

This example shows how to specify a physical drive as a dedicated hot spare for virtual 4:

Server # scope chassis
Server /chassis # scope storageadapter SLOT-3
Server /chassis/storageadapter # scope physical-drive 3
Server /chassis/storageadapter/physical-drive # make-dedicated-hot-spare

5: VD_OS_1, RAID 0, 102400 MB, physical disks: 1
6: VD_OS_2, RAID 0, 12288 MB, physical disks: 1
7: VD_OS_3, RAID 0, 12288 MB, physical disks: 1
8: VD_DATA_1, RAID 0, 12512 MB, physical disks: 1
9: RAID1_2358, RAID 1, 40000 MB, physical disks: 2,3,5,8
11: JFB_RAID1_67, RAID 1, 20000 MB, physical disks: 6,7
12: JFB_Crv_R1_40, RAID 1, 40000 MB, physical disks: 6,7
13: JFB_R1_10GB, RAID 1, 10000 MB, physical disks: 6,7
Please choose from the above 8 virtual drives--> 6

Server /chassis/storageadapter/physical-drive #

make-global-hot-spare

To specify a physical drive as a global hot spare, use the make-global-hot-spare command.

make-global-hot-spare

This command has no arguments or keywords.

Command Default

None

Command Modes

Physical drive (/chassis/storageadapter/physical-drive)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must be logged in as an admin to use this command.

Examples

This example shows how to specify a physical drive as a global hot spare:

Server # scope chassis
Server /chassis # scope storageadapter SLOT-3
Server /chassis/storageadapter # scope physical-drive 3
Server /chassis/storageadapter/physical-drive # make-global-hot-spare
Server /chassis/storageadapter/physical-drive #

map-cifs

To map a CIFS volume as a CIMC-mapped vmedia volume, use the map-cifs command.

map-cifs volume-name remote-share remote-file [mount-options]

Syntax Description

volume-name	Name of the volume.
remote-share	IP address of the volume to be mapped. The value must be in the //server ip/share format.
remote-file	The name and the location of the .iso or .img file in the remote share.
mount-options	(Optional) Industry-standard mount options entered in a comma separated list. Leave the field blank or enter one or more of the following: soft nounix noserverino guest username=VALUE-ignored if guest is entered. password=VALUE-ignored if guest is entered.

Command Default

None

Command Modes

vMedia (/vmedia)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must be logged in as an admin to use this command.

Examples

This example shows how to map a CIFS volume as a CIMC-mapped vMedia volume:

Server # scope vmedia
Server /vmedia # map-cifs sample-volume //10.10.10.10/project /test/sample
Server username: sample-user
Server password: ****
Confirm password: ****

Server /vmedia #

Related Commands

Command	Description
show mapping

map-nfs

To map an NFS volume as a CIMC-mapped vmedia volume, use the map-nfs command.

map-nfs volume-name remote-share remote-file [mount-options]

Syntax Description

volume-name	Name of the volume.
remote-share	IP address of the volume to be mapped. The value must be in the serverip://share format.
remote-file	The name and the location of the .iso or .img file in the remote share.
mount-options	(Optional) Industry-standard mount options entered in a comma separated list. Leave the field blank or enter one or more of the following: ro row nolock noexec soft port=VALUE timeo=VALUE retry=VALUE

Command Default

None

Command Modes

vMedia (/vmedia)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must be logged in as an admin to use this command.

Examples

This example shows how to map an NFS volume as a CIMC-mapped vMedia volume:

Server # scope vmedia
Server /vmedia # map-nfs sample-volume //10.10.10.10/project /test/sample
Server /vmedia #

Related Commands

Command	Description
show mapping

map-www

To map an HTTPS volume as a CIMC-mapped vmedia volume, use the map-www command.

map-www volume-name remote-share remote-file [mount-options]

Syntax Description

volume-name	Name of the volume.
remote-share	IP address of the volume to be mapped. The value must be in the http[s]://serverip/share format.
remote-file	The name and the location of the .iso or .img file in the remote share.
mount-options	(Optional) Industry-standard mount options entered in a comma separated list. Leave the field blank or enter one or more of the following: noauto

Command Default

None

Command Modes

vMedia (/vmedia)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must be logged in as an admin to use this command.

Examples

This example shows how to map an HTTPS volume as a CIMC-mapped vMedia volume:

Server # scope vmedia
Server /vmedia # map-www sample-volume //10.10.10.10/project /test/sample
Server username: sample-user
Server password: ****
Confirm password: ****

Server /vmedia #

Related Commands

Command	Description
show mapping

modify-attributes

To modify the attributes of an existing virtual drive, use the modify-attributes command.

modify-attributes

This command has no arguments or keywords.

Command Default

None

Command Modes

Virtual media (/chassis/storageadapter/virtual-media)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

None

Examples

This example shows how to modify the attribute of virtual drive 3:

Server # scope chassis
Server /chassis # scope storageadapter SLOT-3
Server /chassis/storageadapter # scope virtual-drive 3
Server /chassis/storageadapter/virtual-drive # modify-attributes

Current write policy: Write Back
  0: Write through
  1: Write Back
  2: Write Back Even if Bad BBU

Choose number from above options --> 2
Write policy changed to Write Back Even if Bad BBU

Server /chassis/storageadapter/virtual-drive #

ping (network)

To ping, use the ping command in network mode.

ping address

Syntax Description

address

The IP address or the hostname.

Command Default

None

Command Modes

Network (/cimc/network)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to ping:

server# scope cimc
server /cimc # scope network
server /cimc/network # ping 209.165.200.225

Press CTRL+C to stop.
PING 209.165.200.225 (209.165.200.225): 56 data bytes
64 bytes from 209.165.200.225: seq=0 ttl=122 time=2.000 ms
64 bytes from 209.165.200.225: seq=1 ttl=122 time=2.000 ms
64 bytes from 209.165.200.225: seq=2 ttl=122 time=2.000 ms
64 bytes from 209.165.200.225: seq=3 ttl=122 time=3.000 ms
64 bytes from 209.165.200.225: seq=4 ttl=122 time=2.000 ms

--- 209.165.200.225 ping statistics ---
5 packets transmitted, 5 packets received, 0% packet loss
round-trip min/avg/max = 2.000/2.200/3.000 ms

server /cimc/network #

prepare-for-removal

To prepare a physical drive for removal, use the prepare-for-removal command.

prepare-for-removal

This command has no arguments or keywords.

Command Default

None

Command Modes

Physical drive (/chassis/storageadapter/physical-drive)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must be logged in as an admin to use this command.

Examples

This example shows how to prepare physical drive 3 for removal:

Server # scope chassis
Server /chassis # scope storageadapter SLOT-3
Server /chassis/storageadapter # scope physical-drive 3
Server /chassis/storageadapter/physical-drive # prepare-for-removal
Server /chassis/storageadapter/physical-drive #

power (chassis)

To manage server power, use the power command.

power{ cycle | hard-reset | off | on | shutdown}

Syntax Description

cycle	Power cycles the server.
hard-reset	Hard resets the server.
off	Powers off the server.
on	Powers on the server.
shutdown	Shuts down the server.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to power off the server :

server# scope chassis
server /chassis # power off

This operation will change the server's power state.
Continue?[y|n] y

server /chassis #

Usage Guidelines

Cycle—Power off, then power on.
Hard reset—Power off, then power on. Equivalent to pressing the front panel reset button, or performing an IPMI reset.
Shutdown—Graceful shut down of the OS, then power off.

Related Commands

Command	Description
show chassis
show psu

reapply (bios)

To reapply the boot order, use the reapply command in bios mode.

This command has no arguments or keywords.

Command Default

None

Command Modes

BIOS (/bios)

Command History

Release	Modification
1.0(1x)	This command was introduced.

Examples

This example shows how to reapply the boot order:

server# scope bios
server /bios # re-apply
Boot order has been successfully re-applied
server /bios #

Related Commands

Command	Description
set boot-order (bios)
show actual-boot-order

reboot (chassis)

To reboot the server, use the reboot command.

reboot

This command has no arguments or keywords.

Command Default

None

Command Modes

Cisco Integrated Management Controller (/cimc)

Command History

Release	Modification
1.0(1)	This command was introduced.
1.0(1X)	This command was deprecated.

Examples

This example shows how to reboot the server:

server# scope cimc
server /cimc # reboot

This operation will reboot the BMC.
Continue?[y|n] y

Related Commands

Command	Description
power

rebuild

To rebuild the persistent binding table for the vHBA, use the rebuild command.

rebuild

This command has no arguments or keywords.

Command Default

None

Command Modes

Persistent binding (/chassis/adapter/host-fc-if/perbi)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Note

Persistent binding must be enabled in the vHBA properties.

Examples

This example shows how to rebuild the persistent binding table for the vHBA on interface fc0 on adapter card 1:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # scope perbi
Server /chassis/adapter/host-fc-if/perbi # rebuild

Server /chassis/adapter/host-fc-if/perbi #

Related Commands

Command	Description
show trans-queue

recover (bios)

To recover corrupted BIOS, use the recover command in firmware mode.

recover

This command has no arguments or keywords.

Command Default

None

Command Modes

BIOS (/bios)

Command History

Release	Modification
1.0(1X)	This command was introduced.

Usage Guidelines

Before executing the recover command, perform the following tasks:

Ensure that the BIOS recovery ISO image is available for your use
Launch the KVM Console
Power off server
Map the BIOS recovery ISO image using vMedia

Executing the recover command automatically powers the server on. After the recovery is finished, power cycle or reset the server.

Note

This procedure is not available in some server models.

Examples

This example shows how to recover corrupted BIOS:

server# scope bios
server /bios # recover

This operation will automatically power on the server to perform BIOS FW recovery.
Continue?[y|N]y

server /bios #

Note

You can use the CLI or the KVM console to monitor the progress of the recovery.

Related Commands

Command	Description
show bios
show version

recover-adapter-update

To clear an incomplete firmware update condition, use the recover-adapter-update command.

recover-adapter-update [pci-slot] [pci-slot]

Syntax Description

pci-slot

The PCI slot number of the adapter card to be cleared. You can specify one or two adapters.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.2(1)	This command was introduced.

Usage Guidelines

Use this command to clear the firmware update status if an adapter firmware update has failed or if the adapter status is stuck in the updating state when no update is in progress. This command clears the adapter firmware update status on one or two specified adapters or, if no adapter is specified, on all adapters.

Use the show adapter detail command to view the adapter firmware update status.

Examples

This example shows how to clear the adapter firmware update status on the adapters in PCI slots 3 and 4:

Server# scope chassis
Server /chassis # recover-adapter-update 3 4
Server /chassis #

Related Commands

Command	Description
show adapter
update-adapter-fw

remove-hot-spare

To remove a physical drive from any hot spare pool, use the remove-hot-spare command.

remove-hot-spare

This command has no arguments or keywords.

Command Default

None

Command Modes

Physical drive (/chassis/storageadapter/physical-drive)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must be logged in as an admin to use this command.

Examples

This example shows how to remove physical drive 3 from the hot spare pools:

Server # scope chassis
Server /chassis # scope storageadapter SLOT-3
Server /chassis/storageadapter # scope physical-drive 3
Server /chassis/storageadapter/physical-drive # remove-hot-spare
Server /chassis/storageadapter/physical-drive #

reset-config

To reset the configuration of the cards in the Cisco Flexible Flash controller to default, use the reset-config command.

reset-config primary slot ID

Syntax Description

primary slot ID

Slot ID. The value can either be slot1 or slot2.

Command Default

None

Command Modes

Cisco Flexible Flash Controller (/chassis/flexflash)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

This command reset the configuration of the cards in the Cisco Flexible Flash controller slots.

When you reset the configuration of the slots in the Cisco Flexible Flash card, the following situations occur:

The card in the selected slot is marked as primary healthy.
The card in the other slot is marked as secondary-active unhealthy.
One RAID partition is created.
The card read/write error counts and read/write threshold are set to 0.
Host connectivity could be disrupted.

Examples

This example shows how to reset the configuration of the cards in the Cisco Flexible Flash Controller to the default settings:

Server # scope chassis
Server /chassis # scope flexflash FlexFlash-0 
Server /chassis/flexflash # reset-config slot1
This action will mark the slot1 as healthy primary slot and slot2 (if card existing)
as unhealthy secondary-active.
This operation may disturb the host connectivity as well.
Continue? [y|N] y

Server /chassis/flexflash #

Related Commands

Command	Description
reset
retain-config
scope flexflash
scope operational-profile

reset

To reset the Cisco Flexible Flash controller, use the reset command.

reset

This command has no arguments or keywords.

Command Default

None

Command Modes

Cisco Flexible Flash (/chassis/flexflash)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

When you reset the Cisco Flexible Flash controller, host traffic to the virtual drives (VDs) is disrupted.

Examples

This example shows how to reset the Cisco FlexFlash controller:

Server # scope chassis
Server /chassis # scope flexflash flexflash-0
Server /chassis/flexflash # reset 
This operation will reset the Cisco Flexible Flash Controller.
Host traffic to VDs on this device will be disrupted. 
Continue? [y|N] y
Server /chassis/flexflash #

Related Commands

Command	Description
reset-config
retain-config
scope operation-profile
scope flexflash

restore-mfg-defaults

To restore the BIOS set-up tokens and parameters on the server to the customized manufacturing default values, use the restore-mfg-defaults command.

restore-mfg-defaults

This command has no arguments or keywords.

Command Default

None

Command Modes

BIOS (/bios)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

This command is only available for some C-Series servers.

To use this command, do the following:

The server must be powered off.
You must log in with admin privileges to perform this task.

Examples

This example shows how to restore the BIOS set up tokens to the manufacturing default values:

Server # scope bios
Server /bios # restore-mfg-defaults
This operation will reset the BIOS set-up tokens to manufacturing defaults.
The system will be powered on. 
Continue? [y|n] y
Server /bios #

retain-config

To copy the configuration of one slot to the other slot in the Cisco Flexible Flash card, use the retain-config command.

retain-config primary slot ID

Syntax Description

primary slot ID

Slot ID from which the configuration must be copied from. The value can be slot1 or slot2.

Command Default

None

Command Modes

Cisco Flexible Flash Controller (/chassis/flexflash)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You can use this command for the following situations:

There are two unpaired FlexFlash
The server is operating from a single FlexFlash, and an unpaired FlexFlash is in the other slot.
One FlexFlash supports firmware version 253, and the other FlexFlash is unpartitioned.

When you retain the configuration, the following situations occur:

The configuration for the FlexFlash in the selected slot is copied to the other card.
The card in the selected slot is marked as primary healthy.
The card in the secondary slot is marked as secondary-active unhealthy.

Examples

This example shows how to copy the configuration from slot1 to slot2:

Server # scope chassis
Server /chassis # scope flexflash FlexFlash-0
Server /chassis/flexflash # retain-config slot1
This action will copy the config of slot1 to both the slots, mark slot1 as healthy
primary slot and slot2 (card must be present) as unhealthy secondary-active.
This operation may disturb the host connectivity as well.
Continue? [y|N] y
Server /chassis/flexflash* # commit
Server /chassis/flexflash #

Related Commands

Command	Description
reset
reset-config
retain-config

scope adapter

To enter the adapter command mode, use the scope adapter command.

scope adapter pci-slot

Syntax Description

pci-slot

The PCI slot number of the adapter card.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.2(1)	This command was introduced.

Usage Guidelines

Use this command to enter the command mode for the adapter card at the specified PCI slot.

Examples

This example shows how to enter the adapter command mode for the adapter card in PCI slot 1.

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter #

Related Commands

Command	Description
show adapter

scope advanced

To enter the advanced BIOS command mode, use the scope advanced command.

scope advanced

Syntax Description:

This command has no arguments or keywords.

Command Default

None

Command Modes

BIOS (/bios)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example enters the advanced BIOS command mode:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced #

Related Commands

Command	Description
show advanced

scope bios

To enter bios mode, use the scope bios command.

scope bios

This command has no arguments or keywords.

Command Default

None

Command Modes

BIOS (/bios)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

You use bios mode to set the server boot order:

CDROM—CD-ROM boot
EFI—Extensible Firmware Interface boot
FDD—Floppy disk drive boot
HDD—Hard disk drive boot
PXE—Preboot Execution Environment boot

Examples

This example shows how to enter BIOS mode:

server# scope bios
server /bios #

Related Commands

Command	Description
show bios
show firmware

scope certificate

To enter certificate mode, use the scope certificate command.

scope certificate

This command has no arguments or keywords.

Command Default

None

Command Modes

Certificate (/certificate)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

You use certificate mode to perform the following tasks:

Generate a certificate signing request
Upload a signed certificate

Examples

This example shows how to enter certificate mode:

server# scope certificate
server /certificate #

Related Commands

Command	Description
generate-csr
show certificate

scope chassis

To enter chassis mode, use the scope chassis command.

scope chassis

This command has no arguments or keywords.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

You use chassis mode to set the following chassis properties:

Server description
Server locator LED state

Examples

This example shows how to enter chassis mode:

server# scope chassis
server /chassis #

Related Commands

Command	Description
show chassis
show led

scope cimc

To enter CIMC command mode, use the scope cimc command.

scope cimc

This command has no arguments or keywords.

Command Default

None

Command Modes

Cisco Integrated Management Controller (/cimc)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

You use cimc mode to perform the following actions:

Reset the CIMC to factory defaults
Reboot the CIMC

Examples

This example shows how to enter cimc mode :

server# scope cimc
server /cimc #

Related Commands

Command	Description
show cimc
show log (cimc)

scope comp-queue

To enter the completion queue command mode of the host Ethernet interface, use the scope comp-queue command.

scope comp-queue

This command has no arguments or keywords.

Command Default

None

Command Modes

Ethernet host interface (/chassis/adapter/host-eth-if)

VM FEX (/chassis/adapter/vmfex)

Command History

Release	Modification
1.2(1)	This command was introduced.
1.4(1)	This command was added in the VM FEX command mode.

Examples

This example shows how to enter the completion queue command mode of the host Ethernet interface:

Server# scope chassis
Server/chassis # scope adapter 1
Server/chassis/adapter # scope host-eth-if eth0
Server/chassis/adapter/host-eth-if # scope comp-queue
Server/chassis/adapter/host-eth-if/comp-queue #

Related Commands

Command	Description
set cq-count

scope error-recovery

To enter the Fibre Channel error recovery command mode, use the scope error-recovery command.

scope error-recovery

This command has no arguments or keywords.

Command Default

None

Command Modes

Fibre Channel host interface (/chassis/adapter/host-fc-if)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to enter the error recovery command mode of the host Fibre Channel interface:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # scope error-recovery
Server /chassis/adapter/host-fc-if/error-recovery #

Related Commands

Command	Description
set fcp-error-recovery

scope fan-policy

To enter the fan policy command mode, use the scope fan-policy command.

scope fan-policy

This command has no arguments or keywords.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.5(2)	This command was introduced.

Usage Guidelines

None

Examples

This example shows how to enter the fan policy command mode for a chassis:

server # scope chassis
server /chassis # scope fan-policy
server /chassis/fan-policy #

Related Commands

Command	Description
set fan-policy
show fan-policy

scope fault

To enter fault mode, use the scope fault command.

scope fault

This command has no arguments or keywords.

Command Default

None

Command Modes

Fault (/fault)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

You use fault mode to set the following SNMP properties:

Community string
Platform event

Examples

This example shows how to enter fault mode :

server# scope fault
server /fault #

Related Commands

Command	Description
show fault
show pef

scope firmware

To enter firmware command mode, use the scope firmware command.

scope firmware

This command has no arguments or keywords.

Command Default

None

Command Modes

BIOS (/bios)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use firmware command mode to perform the following tasks:

Activate and upload firmware
Display firmware information

Examples

This example shows how to enter firmware command mode:

server# scope bios
server /bios # scope firmware
server /bios/firmware #

Related Commands

Command	Description
show bios
show firmware

scope flexflash

To enter the Cisco Flexible Flash controller command mode, use the scope flexflash command.

scope flexflash index

Syntax Description

index

The name of the Cisco Flexible Flash controller.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.3(3)	This command was introduced.

Usage Guidelines

Use this command to enter the Cisco Flexible Flash controller command mode.

Examples

This example shows how to enter the Cisco Flexible Flash controller command mode for the first flash device :

Server# scope chassis
Server /chassis # scope flexflash FlexFlash-0
Server /chassis/flexflash #

Related Commands

Command	Description
scope operational-profile

scope gpu

To enter the Nvidia GPU card command mode, use the scope gpu command.

scope gpu slot number

Syntax Description

slot number

Slot number of the GPU card.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

This command is only available on Cisco UCS C-240 servers.

The server must be powered on to use this command.

Examples

This example shows how to enter the Nvidia GPU card command scope:

Server # scope chassis
Server /chassis # show gpu

Slot         Product Name              Num of GPUs
----         ------------              -----------
5            Nvidia GRID K2 @ BD        2

Server /chassis # scope gpu 5
Server /chassis/gpu #

scope host-eth-if

To enter the host Ethernet interface command mode, use the scope host-eth-if command.

scope host-eth-if { eth0 | eth1 | name }

Syntax Description

eth0	Specifies vNIC 0.
eth1	Specifies vNIC 1.
name	Specifies the name of the vNIC.

Command Default

None

Command Modes

Ethernet host interface (/chassis/adapter)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to enter the host Ethernet interface:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if #

Related Commands

Command	Description
scope host-fc-if

scope host-fc-if

To enter the host Fibre Channel interface command mode, use the scope host-fc-if command.

scope host-fc-if { fc0 | fc1 | name }

Syntax Description

fc0	Specifies vHBA fc0.
fc1	Specifies vHBA fc1.
name	Specifies the name of a user-defined vHBA.

Command Default

None

Command Modes

Fibre Channel host nterface (/chassis/adapter)

Command History

Release	Modification
1.2(1)	This command was introduced.
1.4(1)	This command was modified to add the name variable.

Examples

This example shows how to enter the command mode of the host Fibre Channel interface:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc1
Server /chassis/adapter/host-fc-if #

Related Commands

Command	Description
create host-fc-if

scope http

To enter http mode, use the scope http command.

scope http

This command has no arguments or keywords.

Command Default

None

Command Modes

HTTP (/http)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

You use http mode to set the following HTTP properties:

Enabing or disabling HTTP
Specifying port numbers and the HTTP connection timeout

Examples

This example shows how to enter http mode :

server# scope http
server /http #

Related Commands

Command	Description
show http
show http-port

scope iscsi-boot

To enter the iSCSI boot command mode for a vNIC, use the scope iscsi-boot command.

scope iscsi-boot index

Syntax Description

index

The index of the iSCSI boot target. Enter the value 0.

Command Default

None

Command Modes

Host Ethernet Interface (/chassis/adapter/host-eth-if)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

To configure a vNIC as iSCSI-bootable, you must enable the PXE Boot option for the vNIC.

You must be logged in as an admin to perform this task.

Examples

This example shows how to enter the iSCSI boot command mode for a vNIC:

Server # scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # scope iscsi-boot 0
Server /adapter/host-eth-if/iscsi-boot

Related Commands

Command	Description
create iscsi-boot
create iscsi-target

scope import-export

To enter CIMC import-export mode, use the scope import-export command.

scope import-export

Syntax Description:

This command has no arguments or keywords.

Command Default

None

Command Modes

CIMC (/cimc)

Command History

Release	Modification
1.1(2)	This command was introduced.

Usage Guidelines

You can use import-export mode to import or export a CIMC configuration file.

Examples

This example shows how to enter import-export mode:

server# scope cimc
server /cimc # scope import-export
server /cimc/import-export #

Related Commands

Command	Description
export-config
import-config

scope interrupt

To enter interrupt command mode, use the scope interrupt command.

scope interrupt

This command has no arguments or keywords.

Command Default

None

Command Modes

Host Fibre Channel interface (/chassis/adapter/host-fc-if)

Host Ethernet interface (/chassis/adapter/host-eth-if)

VM FEX (/chassis/adapter/vmfex)

Command History

Release	Modification
1.2(1)	This command was introduced.
1.4(1)	This command was added in the VM FEX command mode.

Examples

This example shows how to enter the interrupt command mode of the host Ethernet interface:

Server # scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if
Server /chassis/adapter/host-eth-if # scope interrupt
Server /chassis/adapter/host-eth-if/interrupt #

Related Commands

Command	Description
set interrupt-count

scope ipblocking (network)

To enter ipblocking mode, use the scope ipblocking command in network mode.

scope ipblocking

This command has no arguments or keywords.

Command Default

None

Command Modes

IP blocking (/cimc/network/ipblocking)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

You use ipblocking mode to perform the following tasks:

Enable or disable IP blocking
Set failure count, failure window, and penalty time

Examples

This example shows how to enter ipblocking mode :

server# scope cimc
server /cimc # scope network
server /cimc/network # scope ipblocking
server /cimc/network/ipblocking #

Related Commands

Command	Description
show ipblocking
set penalty-time

scope ipmi

To enter ipmi mode, use the scope ipmi command.

scope ipmi

This command has no arguments or keywords.

Command Default

None

Command Modes

Intelligent Platform Management Interface (/ipmi)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

You use ipmi mode to perform the following tasks:

Enable or disable IPMI
Create an encryption key
Set the security privilege level

Examples

This example shows how to enter ipmi mode :

server# scope ipmi
server /ipmi #

Related Commands

Command	Description
show ipmi
set encryption-key

scope kvm

To enter kvm mode, use the scope kvm command.

scope kvm

This command has no arguments or keywords.

Command Default

None

Command Modes

Keyboard, video and mouse (/kvm)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

You use kvm mode to set the following KVM properties:

Encryption
KVM port number
Local video
Maximum sessions

Examples

This example shows how to enter KVM mode :

server# scope kvm
server /kvm #

Related Commands

Command	Description
set max-sessions
show kvm

scope ldap

To enter ldap mode, use the scope ldap command.

scope ldap

This command has no arguments or keywords.

Command Default

None

Command Modes

Lightweight Directory Access Protocol (/ldap)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

You use ldap mode to perform the following LDAP properties:

Enable or disable LDAP
Set attribute and Base DN (Base Distinguished Name)
Enable encryption
Create LDAP server IP address and connection timeout

Examples

This example shows how to enter ldap mode :

server# scope ldap
server /ldap #

Related Commands

Command	Description
set server-ip
show ldap

scope log (cimc)

To enter log mode, use the scope log command in cimc mode.

scope log

This command has no arguments or keywords.

Command Default

None

Command Modes

Log (/cimc/log)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

You use log mode to perform the following tasks:

Clear the CIMC trace log
Display CIMC trace log entries

Examples

This example shows how to enter log mode :

server# scope cimc
server /cimc # scope log
server /cimc/log #

Related Commands

Command	Description
show entries
show log

scope main

To enter the main BIOS command mode, use the scope main command.

scope main

Syntax Description:

This command has no arguments or keywords.

Command Default

None

Command Modes

BIOS (/bios)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example enters the main BIOS command mode:

Server# scope bios
Server /bios # scope main
Server /bios/main #

Related Commands

Command	Description
show main

scope network (cimc)

To enter network mode, use the scope network command in cimc mode.

scope network

This command has no arguments or keywords.

Command Default

None

Command Modes

Network (/cimc/network)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

You use network mode to perform the following tasks:

Enable DHCP and DNS
Create a host name
Set the NIC mode and redundancy
Create an IPv4 IP address, gateway, and netmask
Enable the VLAN membership feature

Examples

This example shows how to enter network mode :

server# scope cimc
server /cimc # scope network
server /cimc/network #

Related Commands

Command	Description
set dhcp-enabled
show network

scope ntp

To enter Network Time Protocol (NTP) command mode, use the scope ntp command.

scope ntp

This command has no arguments or keywords.

Command Default

None

Command Modes

Network (/cimc/network)

Command History

Release	Modification
1.5(1)	This command was introduced.

Examples

This example shows how to enter the NTP command mode:

Server # scope cimc
Server /cimc # scope network
Server /cimc/network # scope ntp
Server /cimc/network/ntp # set enabled yes 
Warning: IPMI set SEL Time Command will be 
disabled if NTP is enabled. 
Do you wish to continue? [y|N]  
y
Server /cimc/network/ntp* # commit
Server /cimc/network/ntp # set server-1 10.120.33.44
Server /cimc/network/ntp* # set server-2 10.120.34.45
Server /cimc/network/ntp* # set server-3 10.120.35.46
Server /cimc/network/ntp* # set server-4 10.120.36.48
Server /cimc/network/ntp* # commit

Related Commands

Command	Description
set enabled
set server-1
set server-2
set server-3
set server-4
show ntp

scope offload

To enter the TCP offload command mode, use the scope offload command.

scope offload

This command has no arguments or keywords.

Command Default

None

Command Modes

Host Fibre Channel interface (/chassis/adapter/host-fc-if)

Host Ethernet interface (/chassis/adapter/host-eth-if)

VM FEX (/chassis/adapter/vmfex)

Command History

Release	Modification
1.2(1)	This command was introduced.
1.4(1)	This command was added in the VM FEX command mode.

Examples

This example shows how to enter the TCP offload command mode:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # scope offload
Server /chassis/adapter/host-eth-if/offload #

Related Commands

Command	Description
set tcp-segment-offload

scope operational-profile

To enter the Cisco Flexible Flash operational profile command mode, use the scope operational-profile command.

scope operational-profile

This command has no arguments or keywords.

Command Default

None

Command Modes

FlexFlash (/chassis/flexflash)

Command History

Release	Modification
1.3(3)	This command was introduced.

Usage Guidelines

Use this command to enter the Cisco Flexible Flash operational profile command mode.

Examples

This example shows how to enter the Cisco Flexible Flash operational profile command mode for the first flash device:

Server# scope chassis
Server /chassis # scope flexflash FlexFlash-0
Server /chassis/flexflash # scope operational-profile
Server /chassis/flexflash/operational-profile #

Related Commands

Command	Description
set error-count-threshold
set raid-primary-member
set virtual-drives-enabled

scope pef (fault)

To enter pef mode, use the scope pef command in fault mode.

scope pef pef-index

Syntax Description

pef-index

The index of a specific performance event filter. The range of valid values is 1 to 12. See Usage Guideline for a complete list of perfomance event filter indexes.

Command Default

None

Command Modes

Performance event filter (/fault/pef)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Following is a list of the performance event filter indexes:

1—Temperature Critical Assert Filter
2—Temperature Warning Assert Filter
3—Voltage Critical Assert Filter
4—Current Assert Filter
5—Fan Critical Assert Filter
6—Processor Assert Filter
7—Power Supply Critical Assert Filter
8—Power Supply Warning Assert Filter
9—Power Supply Redundancy Lost Filter
10—Discrete Power Supply Assert Filter
11—Memory Assert Filter
12—Drive Slot Assert Filter

Examples

This example shows how to enter pef mode:

server# scope fault
server /fault # scope pef 3
server /fault/pef #

Related Commands

Command	Description
show pef

scope pef-destinations

To enter platform event filter destination mode, use scope pef-destinations command.

scope pef-destinations

This command has no arguments or keywords.

Command Default

None

Command Modes

pef-destinations (/pef-destinations)

Command History

Release	Modification
Release 1.5(1)	This command was introduced.

Usage Guidelines

You use platform event filter destination mode to set the following event trap destination properties:

Enabling the event trap destination.
Platform event trap destination IP address.

Examples

This example shows how to enter platform event filter destination mode :

server# scope pef
server# /fault # scope pef-destinations
server /fault /pef-destinations #

scope perbi

To enter the persistent LUN binding command mode for the vHBA, use the scope perbi command.

scope perbi

This command has no arguments or keywords.

Command Default

None

Command Modes

Host Fibre Channel interface (/chassis/adapter/host-fc-if )

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to enter the persistent LUN binding command mode of the host Fibre Channel interface:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # scope perbi 
Server /chassis/adapter/host-fc-if/perbi #

Related Commands

Command	Description
set persistent-lun-binding enable

scope physical-drive

To enter the physical drive command mode, use the scope physical-drive command.

scope physical-drive drive-number

Syntax Description

drive-number

The drive number of the physical drive.

Command Default

None

Command Modes

Storage adapter (/chassis/storageadapter)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

You can use the physical-drive command mode to display general, inquiry, and status information about a physical drive.

Examples

This example shows how to enter the physical drive command mode for physical drive number 1 on the storage adapter named SAS:

server# scope chassis
server /chassis # scope storageadapter SAS
server /chassis/storageadapter # scope physical-drive 1
server /chassis/storageadapter/physical-drive #

Related Commands

Command	Description
show physical-drive

scope port

To enter the Fibre Channel port command mode, use the scope port command.

scope port

This command has no arguments or keywords.

Command Default

None

Command Modes

Host Fibre Channel interface (/chassis/adapter/host-fc-if)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to enter the Fibre Channel port command mode.

Server # scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # scope port
Server /chassis/adapter/host-fc-if/port #

Related Commands

Command	Description
set max-target-luns
set outstanding-io-count

scope port-f-logi

To enter the Fibre Channel fabric login command mode, use the scope port-f-logi command.

scope port-f-logi

This command has no arguments or keywords.

Command Default

None

Command Modes

Host Fibre Channel interface (/chassis/adapter/host-fc-if)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to enter the Fibre Channel fabric login command mode:

Server # scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # scope port-f-logi
Server /chassis/adapter/host-fc-if/port-f-logi #

Related Commands

Command	Description
set flogi-retries
set flogi-timeout

scope port-p-logi

To enter the Fibre Channel port login command mode, use the scope port-p-logi command.

scope port-p-logi

This command has no arguments or keywords.

Command Default

None

Command Modes

Host Fibre Channel interface (/chassis/adapter/host-fc-if)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to enter the Fibre Channel port login command mode:

Server # scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # scope port-p-logi
Server /chassis/adapter/host-fc-if/port-p-logi #

Related Commands

Command	Description
set plogi-retries
set plogi-timeout

scope recv-queue

To enter the receive queue command mode, use the scope recv-queue command.

scope recv-queue

This command has no arguments or keywords.

Command Default

None

Command Modes

Host Ethernet interface (/chassis/adapter/host-eth-if )

Host Fibre Channel interface (/chassis/adapter/host-fc-if )

VM FEX (/chassis/adapter/vmfex)

Command History

Release	Modification
1.2(1)	This command was introduced.
1.4(1)	This command was added in the VM FEX command mode.

Examples

This example shows how to enter the Fibre Channel receive queue command mode:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # scope recv-queue
Server /chassis/adapter/host-fc-if/recv-queue #

Related Commands

Command	Description
set rq-count
set rq-ring-size

scope role-group

To enter the command mode of an Active Directory role group, use the scope role-group command.

scope role-group index

Syntax Description

index

The numeric identifier of the available role groups, from 1 to 5.

Command Default

None

Command Modes

LDAP (/ldap)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to enter the command mode of an Active Directory (AD) authorization (role) group.

Examples

This example shows how to enter the command mode of AD role group number 1:

Server# scope ldap
Server /ldap # scope role-group 1
Server /ldap/role-group #

Related Commands

Command	Description
set name
set domain
set role

scope rss

To enter the Receive-Side Scaling (RSS) command mode, use the scope rss command.

scope rss

This command has no arguments or keywords.

Command Default

None

Command Modes

Ethernet host interface (/chassis/adapter/host-eth-if)

VM FEX (/chassis/adapter/vmfex)

Command History

Release	Modification
1.2(1)	This command was introduced.
1.4(1)	This command was added in the VM FEX command mode.

Examples

This example shows how to enter the Receive-Side Scaling (RSS) command mode:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # scope rss
Server /chassis/adapter/host-eth-if/rss #

Related Commands

Command	Description
set rss

scope scsi-io

To enter the SCSI I/O command mode, use the scope scsi-io command.

scope scsi-io

This command has no arguments or keywords.

Command Default

None

Command Modes

SCSI-IO (/chassis/adapter/host-fc-if/scsi-io)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to enter the the SCSI I/O command mode:

Server # scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # scope scsi-io
Server /chassis/adapter/host-fc-if/scsi-io #

Related Commands

Command	Description
set cdb-wq-count

scope sel

To enter sel mode, use the scope sel command.

scope sel

This command has no arguments or keywords.

Command Default

None

Command Modes

System event log (/sel)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

You use sel mode to perform the following tasks:

Clear the system event log
Show configuration and system event log entries

Examples

This example shows how to enter sel mode :

server# scope sel
server /sel #

Related Commands

Command	Description
show entries
show sel

scope sensor

To enter sensor mode, use the scope sensor command.

scope sensor

This command has no arguments or keywords.

Command Default

None

Command Modes

Sensor (/sensor)

Command History

Release	Modification
1.0(1X)	This command was introduced.

Usage Guidelines

You use sensor mode to display fan, psu, psu-redundancy, temperature, and voltage sensors information.

Examples

This example shows how to enter sensor mode :

server# scope sensor
server /sensor #

Related Commands

Command	Description
show fan
show voltage

scope server-management

To enter the server management BIOS command mode, use the scope server-management command.

scope server-management

Syntax Description:

This command has no arguments or keywords.

Command Default

None

Command Modes

BIOS (/bios)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example enters the server management BIOS command mode:

Server# scope bios
Server /bios # scope server-management
Server /bios/server-management #

Related Commands

Command	Description
show server-management

scope server (log)

To enter the command mode for a remote syslog server profile, use the scope server command.

scope server { 1 | 2 }

Syntax Description

1	Selects remote syslog server profile number 1.
2	Selects remote syslog server profile number 2.

Command Default

None

Command Modes

CIMC log (/cimc/log)

Command History

Release	Modification
1.1(2)	This command was introduced.

Usage Guidelines

You can configure two remote syslog server profiles for sending CIMC log entries to different destinations. Use this command to select a profile and enter the command mode for that profile.

Examples

This example shows how to access and configure syslog server profile number 2:

server# scope cimc
server /cimc # scope log
server /cimc/log # scope server 2
server /cimc/log/server # set server-ip 192.0.2.34
server /cimc/log/server *# set enabled yes
server /cimc/log/server *# commit
server /cimc/log/server #

Related Commands

Command	Description
set enabled (server)
set server-ip

scope snmp

To enter the SNMP command mode, use the scope snmp command.

scope snmp

Syntax Description:

This command has no arguments or keywords.

Command Default

None

Command Modes

SNMP (/snmp)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

You can use the SNMP command mode to configure SNMP parameters such as location and contact.

Examples

This example shows how to enter SNMP command mode:

server# scope snmp
server /snmp #

Related Commands

Command	Description
scope trap-destination
show snmp

scope sol

To enter sol mode, use the scope sol command.

scope sol

This command has no arguments or keywords.

Command Default

None

Command Modes

Serial over LAN (/sol)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

You use sol mode to perform the following tasks:

Enable or disable SoL
Set the baud rate

Examples

This example shows how to enter sol mode :

server# scope sol
server /sol #

Related Commands

Command	Description
set baud-rate
show sol

scope ssh

To enter ssh mode, use the scope ssh command.

scope ssh

This command has no arguments or keywords.

Command Default

None

Command Modes

Secure Shell (/ssh)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

You use ssh mode to perform the following tasks:

Enable or disable SSH
Set the SSH port number and connection timeout interval

Examples

This example shows how to enter ssh mode :

server# scope ssh
server /ssh #

Related Commands

Command	Description
set timeout (/ssh)
show ssh

scope storageadapter

To enter the storageadapter command mode, use the scope storageadapter command.

scope storageadapter slot

Syntax Description

slot	The PCI slot name or number of the storage adapter.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

You can use the storage adapter command mode to view storage adapter parameters such as the following:

Firmware images and versions
PCI information
Manufacturing information
Battery backup unit information
Supported RAID levels
Harware information
Error counters

Examples

This example shows how to enter storage adapter command mode for the adapter in slot 2:

Server# scope chassis
Server /chassis # scope storageadapter SLOT-2
Server /chassis/storageadapter #

Related Commands

Command	Description
show storageadapter

scope tech-support (cimc)

To enter tech-support mode, use the scope tech-support command in cimc mode.

scope tech-support

This command has no arguments or keywords.

Command Default

None

Command Modes

Technical support (/cimc/tech-support)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

You use tech-support mode to set up the TFTP path and server address.

Examples

This example shows how to enter tech-support mode :

server# scope cimc
server /cimc # scope tech-support
server /cimc/tech-support #

Related Commands

Command	Description
show tech-support
start

scope trans-queue

To enter the transmit queue command mode, use the scope trans-queue command.

scope trans-queue

This command has no arguments or keywords.

Command Default

None

Command Modes

Ethernet host interface (/chassis/adapter/host-eth-if )

Fibre Channel host interface (/chassis/adapter/host-fc-if )

VM FEX (/chassis/adapter/vmfex)

Command History

Release	Modification
1.2(1)	This command was introduced.
1.4(1)	This command was added in the VM FEX command mode.

Examples

This example shows how to enter the Ethernet transmit queue command mode:

Server # scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # scope trans-queue
Server /chassis/adapter/host-eth-if/trans-queue #

Related Commands

Command	Description
set wq-count
set wq-ring-size

scope trap-destination

To enter trap-destination command mode, use the scope trap-destination command.

scope trap-destination trap-destination-index

Syntax Description

trap-destination-index

The index of a specific trap destination profile.

Command Default

None

Command Modes

Trap destination (/snmp/trap-destination)

Command History

Release	Modification
1.0(1)	This command was introduced.
1.4(1)	This command was moved from the fault command mode to the snmp command mode.

Usage Guidelines

Use this command to access the four configurable trap destination profiles, identified by index numbers 1 through 4.

Examples

This example shows how to enter trap-destination mode:

Server# scope fault
Server /snmp # scope trap-destination 4
Server /snmp/trap-destination #

Related Commands

Command	Description
set addr (trap-destination)
show trap-destination

scope user

To enter user mode, use the scope user command.

scope user { 1 | | 2 | | 3 | | 4 | | 5 | | 6 | | 7 | | 8 | | 9 | | 10 | | 11 | | 12 | | 13 | | 14 | | 15 }

Syntax Description

1

through

15

Specifies users 1 through 15.

Command Default

None

Command Modes

User (/user)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

You use user mode to perform the following tasks:

Enable user services
Create user names, roles, and passwords

Examples

This example shows how to enter user mode :

server# scope user 1
server /user #

Related Commands

Command	Description
set user-name
show user

scope user-session

To enter user-session mode, use the scope user-session command.

scope user-session index

Syntax Description

index

The session ID of a specific user session.

Command Default

None

Command Modes

User session (/user-session)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

You use user-session mode to display details about user sessions.

Examples

This example shows how to enter user-session mode :

server# scope user-session 31
server /user-session #

Related Commands

Command	Description
show user
show user-session

scope v3users

To enter the command mode for an SNMPv3 user, use the scope v3users command.

scope v3users user-index

Syntax Description

user-index

The number of the user to configure.

Command Default

None

Command Modes

SNMP (/snmp)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to enter the command mode for an SNMPv3 user. Specify a user number between 1 and 15.

Examples

This example enters the command mode for SNMPv3 user number 1:

Server# scope snmp
Server /snmp # scope v3users 1
Server /snmp/v3users #

Related Commands

Command	Description
show v3users

scope virtual-drive

To enter the virtual drive command mode, use the scope virtual-drive command.

scope virtual-drive drive-number

Syntax Description

drive-number

The drive number of the virtual drive.

Command Default

None

Command Modes

Storage adapter (/chassis/storageadapter)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example shows how to enter the virtual drive command mode for virtual drive number 1 on the storage adapter named SAS:

server# scope chassis
server /chassis # scope storageadapter SAS
server /chassis/storageadapter # scope virtual-drive 1
server /chassis/storageadapter/virtual-drive #

Related Commands

Command	Description
show virtual-drive

scope vmedia

To enter vmedia mode, use the scope vmedia command.

scope vmedia

This command has no arguments or keywords.

Command Default

None

Command Modes

Virtual media (/vmedia)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

You use vmedia mode to perform the following tasks:

Enable virtual media services
Enable encryption

Examples

This example shows how to enter vmedia mode :

server# scope vmedia
server /vmedia #

Related Commands

Command	Description
set
show vmedia

scope vmfex

To enter the VM FEX command mode, use the scope vmfex command.

scope vmfex port-id

Syntax Description

port-id

The name or number of the host Ethernet interface.

Command Default

None

Command Modes

Adapter (/chassis/adapter)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to enter the virtual machine fabric extender (VM FEX) command mode for the specified host Ethernet interface. NIV mode must be enabled.

Examples

This example shows how to enter the VM FEX command mode for the host Ethernet interface named pts0:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope vmfex pts0
Server /chassis/adapter/vmfex #

Related Commands

Command	Description
show vmfex

sendSNMPtrap

To send a test message to the SNMP trap destination, use the sendSNMPtrap command.

sendSNMPtrap

Syntax Description:

This command has no arguments or keywords.

Command Default

None

Command Modes

SNMP trap destinations (/snmp/trap-destinations)

Command History

Release	Modification
1.3(1)	This command was introduced.
1.4(1)	This command was moved from the fault scope to the snmp scope.

Usage Guidelines

Use this command to send an SNMPv1 test trap to the SNMP trap destination. The trap must be configured and enabled in order to send a test message.

Examples

This example sends a test message to SNMP trap destination 1:

Server# scope snmp
Server /snmp # scope trap-destinations 1
Server /snmp/trap-destinations # sendSNMPtrap
SNMP Test Trap sent to Destination:1
Server /snmp/trap-destination #

Related Commands

Command	Description
scope trap-destinations

sendPEFtrap

To send a test message to the Platform Event Filter (PEF) trap destination, use the sendPEFtrap command.

sendPEFtrap

Syntax Description:

This command has no arguments or keywords.

Command Default

None

Command Modes

PEF trap destination (/fault/pef-destinations)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

Use this command to send an PEF test trap to the trap destination. The trap must be configured and enabled in order to send a test message.

Examples

This example sends a test message to PEF trap destination 1:

Server# scope fault
Server /fault # scope pef-destinations 1
Server /fault/pef-destinations # sendPEFtrap
PEF Test Trap sent to Destination:1
Server /snmp/pef-destinations #

Related Commands

Command	Description
scope pef-destinations

set ACPI10Support

To specify whether the BIOS publishes the ACPI 1.0 version, use the set ACPI10Support command.

set ACPI10Support { Disabled | Enabled }

Syntax Description

Disabled	The ACPI 1.0 version is not published.
Enabled	The ACPI 1.0 version is published.

Command Default

The ACPI 1.0 version is not published.

Command Modes

Server Management BIOS (/bios/server-management)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Use this command to specify whether the BIOS publishes the Advanced Configuration and Power Interface (ACPI) 1.0 version of the fixed ACPI description table (FADT) in the Root System Description table. This version may be required for compatibility with OS versions that support only ACPI 1.0.

Examples

This example configures the BIOS to publish the ACPI 1.0 version and commits the transaction:

Server# scope bios
Server /bios # scope server-management
Server /bios/server-management # set ACPI10Support Enabled
Server /bios/server-management *# commit
Server /bios/server-management #

Related Commands

Command	Description
show server-management

set action (pef)

To set up an action for a performance event filter, use the set action command in pef mode.

set action { none | | power-off | | reboot | | power-cycle }

Syntax Description

none	Specifies no action.
power-off	Specifies that the server power off.
reboot	Specifies that the server reboots.
power-cycle	Specifies that the server power cycle.

Command Default

None

Command Modes

Performance event filters (/fault/pef)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Following is a list of the performance event filter indexes:

1—Temperature Critical Assert Filter
2—Temperature Warning Assert Filter
3—Voltage Critical Assert Filter
4—Current Assert Filter
5—Fan Critical Assert Filter
6—Processor Assert Filter
7—Power Supply Critical Assert Filter
8—Power Supply Warning Assert Filter
9—Power Supply Redundancy Lost Filter
10—Discrete Power Supply Assert Filter
11—Memory Assert Filter
12—Drive Slot Assert Filter

Examples

This example shows how to set up an action for performance event filter 3:

server# scope fault
server /fault # scope pef 3
server /fault/pef # set action power-cycle
server /fault/pef* # commit
server /fault/pef #

Related Commands

Command	Description
show pef

set ActiveVideo

To specify how the server displays video, use the set ActiveVideo command.

set ActiveVideo { Auto | Onboard_Device }

Syntax Description

Auto	The server uses an external graphics adapter for display if one is available.
Onboard_Device	The server always uses its internal graphics adapter even if an external graphics adapter is available.

Command Default

The server uses an external graphics adapter for display if one is available (Auto).

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(1)	This command was introduced.

Examples

This example specifies that the server always uses its internal graphics adapter and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set ActiveVideo Onboard_Device
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set addr (trap-destination)

To assign an IP address to an SNMP trap destination index, use the set addr command in trap-destination mode.

set addr ip-address

Syntax Description

ip-address

The IP address of the trap destination. The format is x.x.x.x.

Command Default

None

Command Modes

SNMP trap destination (/snmp/trap-destination)

Command History

Release	Modification
1.0(1)	This command was introduced.
1.4(1)	This command was moved from the fault scope to the snmp scope.

Examples

This example shows how to assign an IP address to a trap destination index:

server# scope snmp
server /snmp # scope trap-destination 3
server /snmp/trap-destination # set addr 209.165.200.225
server /snmp/trap-destination* # commit
server /snmp/trap-destination #

Related Commands

Command	Description
show trap-destination

set AdjacentCacheLinePrefetch

To specify whether the processor uses the Intel Adjacent Cache Line Prefetch mechanism, use the set AdjacentCacheLinePrefetch command.

set AdjacentCacheLinePrefetch { Disabled | Enabled }

Syntax Description

Disabled	The Adjacent Cache Line Prefetch mechanism is not used.
Enabled	The Adjacent Cache Line Prefetch mechanism is used when cache issues are detected.

Command Default

The Adjacent Cache Line Prefetch mechanism is used when cache issues are detected.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Use this command to specify whether the processor uses the Intel Adjacent Cache Line Prefetch mechanism to fetch data when necessary.

You must select the Custom option in the set CPUPerformance command in order to specify this value. For any value other than Custom, this setting is overridden by the setting in the selected CPU performance profile.

Examples

This example specifies that the processor uses the Adjacent Cache Line Prefetch mechanism when necessary and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set CPUPerformance Custom
Server /bios/advanced # set AdjacentCacheLinePrefetch Enable
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set CPUPerformance
show advanced

set alternate-dns-server

To specify the IP address of the secondary DNS server, use the set alternate-dns-server command.

set alternate-dns-server dns2-ipv4-address

Syntax Description

dns2-ipv4-address

The IP address of the secondary DNS server.

Command Default

None

Command Modes

Network (/cimc/network)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example specifies the IP address of the secondary DNS server:

server# scope cimc
server /cimc # scope network
server /cimc/network # set alternate-dns-server 192.0.20.2
server /cimc/network* # commit
server /cimc/network #

Related Commands

Command	Description
set preferred-dns-server
show network

set Altitude

To specify the approximate number of meters above sea level at which the physical server is installed, use the set Altitude command.

set Altitude { Auto | 300_M | 900_M | 1500_M | 3000_M }

Syntax Description

Auto	The CPU determines the physical elevation.
300_M	The server is approximately 300 meters above sea level.
900_M	The server is approximately 900 meters above sea level.
1500_M	The server is approximately 1500 meters above sea level.
3000_M	The server is approximately 3000 meters above sea level.

Command Default

The server is approximately 300 meters above sea level.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(5)	This command was introduced.

Examples

This example specifies that the server is installed at approximately 900 meters above sea level and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set Altitude 900_M
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set AssertNMIOnPERR

To specify whether the BIOS generates a non-maskable interrupt (NMI) and logs an error when a processor bus parity error (PERR) occurs, use the set AssertNMIOnPERR command.

set AssertNMIOnPERR { Disabled | Enabled }

Syntax Description

Disabled	The BIOS does not generate an NMI or log an error when a PERR occurs.
Enabled	The BIOS generates an NMI and logs an error when a PERR occurs.

Command Default

Enabled

Command Modes

Server Management BIOS (/bios/server-management)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Note

If you enable an NMI when a PERR occurs, you must also enable an NMI when a SERR occurs, using the set AssertNMIonSERR command.

Examples

This example configures the BIOS to not generate an NMI or log an error when a PERR occurs, and commits the transaction:

Server# scope bios
Server /bios # scope server-management
Server /bios/server-management # set AssertNMIOnPERR Disabled
Server /bios/server-management *# commit
Server /bios/server-management #

Related Commands

Command	Description
set AssertNMIOnSERR
show server-management

set AssertNMIOnSERR

To specify whether the BIOS generates a non-maskable interrupt (NMI) and logs an error when a system error (SERR) occurs, use the set AssertNMIOnSERR command.

set AssertNMIOnSERR { Disabled | Enabled }

Syntax Description

Disabled	The BIOS does not generate an NMI or log an error when a SERR occurs.
Enabled	The BIOS generates an NMI and logs an error when a SERR occurs.

Command Default

Enabled

Command Modes

Server Management BIOS (/bios/server-management)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Note

If you enable an NMI when a PERR occurs, using the set AssertNMIonPERR command, you must also enable an NMI when a SERR occurs, using this command.

Examples

This example configures the BIOS to not generate an NMI or log an error when a SERR occurs, and commits the transaction:

Server# scope bios
Server /bios # scope server-management
Server /bios/server-management # set AssertNMIOnSERR Disabled
Server /bios/server-management *# commit
Server /bios/server-management #

Related Commands

Command	Description
set AssertNMIOnPERR
show server-management

set ATS

To specify whether the processor supports Intel VT-d Address Translation Services (ATS), use the set ATS command.

set ATS { Disabled | Enabled }

Syntax Description

Disabled	The processor does not support ATS.
Enabled	The processor uses VT-d ATS as required.

Command Default

The processor uses VT-d ATS as required.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example specifies that the processor does not support ATS and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set ATS Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set attribute

To specify the LDAP attribute, use the set attribute command.

set attribute attribute-name

Syntax Description

attribute-name

The name of the attribute. The name can be up to 64 characters.

Command Default

None

Command Modes

LDAP (/ldap)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to specify an LDAP attribute that contains the role and locale information for the user. This property is always a name-value pair. The system queries the user record for the value that matches this attribute name.

You can use an existing LDAP attribute that is mapped to the CIMC user roles and locales or you can create a custom attribute, such as the CiscoAVPair attribute, which has the following attribute ID: 1.3.6.1.4.1.9.287247.1

Note

If you do not specify this property, user access is restricted to read-only.

Examples

This example specifies the attribute as the CiscoAVPair attribute:

server# scope ldap
server /ldap # set enabled yes
server /ldap* # set attribute CiscoAVPair
server /ldap* # commit
server /ldap #

Related Commands

Command	Description
show ldap

set base-dn

To specify the top level domain name of the LDAP hierarchy, use the set base-dn command.

set base-dn base-dn-name

Syntax Description

base-dn-name

The name of the LDAP Base DN. The name can contain up to 63 characters.

Command Default

None

Command Modes

LDAP (/ldap)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example specifies the base-dn as cisco.com:

server# scope ldap
server /ldap # set enabled yes
server /ldap* # set base-dn cisco.com
server /ldap* # commit
server /ldap #

Related Commands

Command	Description
show ldap

set baud-rate

To specify the baud rate for serial over LAN (SoL) communications, use the set baud-rate command.

set baud-rate { 9.6k | 19.2k | 38.4k | 57.6k | 115.2k }

Syntax Description

9.6k	The baud rate is 9600 bps.
19.2k	The baud rate is 19200 bps.
38.4k	The baud rate is 38400 bps.
57.6k	The baud rate is 57600 bps.
115.2k	The baud rate is 115200 bps.

Command Default

The baud rate is 115200 bps.

Command Modes

Serial over LAN (/sol)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Note

This setting must match the setting on the remote terminal application.

Examples

This example configures a baud rate of 57600 bps on the serial port and commits the transaction:

Server# scope sol
Server /sol # set baud-rate 57.6k
Server /sol *# set enabled yes
Server /sol *# commit
Server /sol #

Related Commands

Command	Description
show sol

set BaudRate

To specify the baud rate for serial port communications, use the set BaudRate command.

set BaudRate { 9.6k | 19.2k | 38.4k | 57.6k | 115.2k }

Syntax Description

9.6k	The baud rate is 9600 bps.
19.2k	The baud rate is 19200 bps.
38.4k	The baud rate is 38400 bps.
57.6k	The baud rate is 57600 bps.
115.2k	The baud rate is 115200 bps.

Command Default

The baud rate is 9600 bps.

Command Modes

Server Management BIOS (/bios/server-management)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Use this command to specify the baud rate for serial port communications. If you disable Console Redirection, this option is not available.

Note

This setting must match the setting on the remote terminal application.

Examples

This example configures a baud rate of 115200 bps on the serial port and commits the transaction:

Server# scope bios
Server /bios # scope server-management
Server /bios/server-management # set BaudRate 115.2k
Server /bios/server-management *# commit
Server /bios/server-management #

Related Commands

Command	Description
show server-management

set BMCPnP

To specify whether the system automatically detects the BMC in ACPI-compliant operating systems, use the set BMCPnP command.

set BMCPnP { Disabled | Enabled }

Syntax Description

Disabled	The system never automatically detects the BMC.
Enabled	The system automatically detects the BMC whenever possible.

Command Default

Disabled

Command Modes

Server Management BIOS (/bios/server-management)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example configures the BIOS to automatically detect the BMC whenever possible and commits the transaction:

Server# scope bios
Server /bios # scope server-management
Server /bios/server-management # set BMCPnP Enabled
Server /bios/server-management *# commit
Server /bios/server-management #

Related Commands

Command	Description
show server-management

set boot

To enable or disable remote boot for an adapter interface, use the set boot command.

set boot { disable | enable }

Syntax Description

disable	Disables remote boot.
enable	Enables remote boot.

Command Default

Remote boot is disabled for default vHBAs and user-created vNICs, and enabled for default vNICs.

Command Modes

Ethernet host interface (/chassis/adapter/host-eth-if)

Fibre Channel host interface (/chassis/adapter/host-fc-if)

Command History

Release	Modification
1.2(1)	This command was introduced.

Usage Guidelines

Use this command to specify whether a vNIC can boot from PXE or whether a vHBA can boot from SAN.

Examples

This example shows how to enable SAN boot for the host Fibre Channel interface fc0:

Server# scope chassis
Server/chassis # scope adapter 1
Server/chassis/adapter # scope host-fc-if fc0
Server/chassis/adapter/host-fc-if # set boot enable
Server/chassis/adapter/host-fc-if *# commit
Server/chassis/adapter/host-fc-if #

Related Commands

Command	Description
create-boot-entry

set-boot-drive

To specify a virtual drive from which the controller must boot from, use the set-boot-drive command.

set-boot-drive

This command has no arguments or keywords.

Command Default

None

Command Modes

Virtual drive (/chassis/storageadapter/virtual-drive)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must be logged in as an admin to use this command.

Examples

This example shows how to specify the controller to boot from virtual drive 3:

Server# scope chassis
Server /chassis # scope storageadapter SLOT-3
Server /chassis/storageadapter # scope virtual-drive 3
Server /chassis/storageadapter/virtual-drive # set-boot-drive
Are you sure you want to set virtual drive 3 as the boot drive?
Enter 'yes' to confirm -> yes
Server /chassis/storageadapter/virtual-drive #

set boot-lun

To set a boot LUN for an iSCSI target, use the set boot-lun command.

set boot-lun value

Syntax Description

value

Specifies the target boot LUN for an iSCSI target. Specify a number between 0 and 65535.

Command Default

None

Command Modes

iSCSI target (/chassis/adapter/host-eth-if/iscsi-boot/iscsi-target)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

None

Examples

This example shows how to set the boot LUN for an iSCSI target to 3:

Server # scope chassis
Server /chassis # scope adapter 3
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # scope iscsi-boot 0
Server /chassis/adapter/host-eth-if/iscsi-boot # create iscsi-target 1
Server /chassis/adapter/host-eth-if/iscsi-boot/iscsi-target* # set boot-lun 3
Server /chassis/adapter/host-eth-if/iscsi-boot/iscsi-target* # commit
Server /chassis/adapter/host-eth-if/iscsi-boot/iscsi-target #

Related Commands

Command	Description
set chap-name
set chap-secret
set ipaddr
set iqn

set boot-order

To set the boot order for the server, use the set boot-order command in BIOS mode.

set boot-order boot-list

Syntax Description

boot-list

A comma-separated list of boot devices.

Command Default

None

Command Modes

BIOS (/bios)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

For the boot-list argument, type the boot devices in the desired boot order using commas as delimiters, with no spaces between devices. The device names are not case sensitive. Use one or more of the following boot device arguments:

hdd
pxe
fdd
efi
cdrom

Installed boot devices not listed in this command will be appended to the boot order. If a listed device is not present, it will be removed from the boot order configuration.

Do not disable boot options in the BIOS menus.

Examples

This example shows how to specify the boot order for the server:

server# scope bios
server /bios # set boot-order efi,hdd,fdd,cdrom,pxe
server /bios* # commit
server /bios #

Related Commands

Command	Description
show bios
show actual-boot-order

set BootOptionRetry

To specify whether the BIOS retries NON-EFI based boot options without waiting for user input, use the set BootOptionRetry command.

set BootOptionRetry { Disabled | Enabled }

Syntax Description

Disabled	The BIOS waits for user input before retrying NON-EFI based boot options.
Enabled	The BIOS continually retries NON-EFI based boot options without waiting for user input.

Command Default

The BIOS waits for user input before retrying NON-EFI based boot options.

Command Modes

Main BIOS (/bios/main)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example configures the BIOS to continually retry NON-EFI based boot options without waiting for user input and commits the transaction:

Server# scope bios
Server /bios # scope main
Server /bios/main # set BootOptionRetry Enabled
Server /bios/main *# commit
Server /bios/main *# show detail
Set-up parameters:
    Boot option retry: Enabled
    POST Error Pause: Disabled

Server /bios/main #

Related Commands

Command	Description
scope main
show main

set boot-override

To specify a device that will override the default boot priority the next time the server boots, use the set boot-override command.

set boot-override { None | SCU | HV | HUU }

Syntax Description

None	The server uses the default boot order.
SCU	The server boots from the Cisco UCS Server Configuration Utility.
HV	The server boots from the VMware Hypervisor.
HUU	The server boots from the Cisco Host Upgrade Utility.

Command Default

None

Command Modes

BIOS (/bios)

Command History

Release	Modification
1.3(3)	This command was introduced.

Usage Guidelines

Use this command to specify a device that will override the default boot priority the next time the server is restarted, regardless of the default boot order defined for the server. The specified device is used only once. After the server has rebooted, this option is ignored. The available devices are virtual drives on the Cisco Flexible Flash card.

Note

This function is available only on platforms that support the Cisco Flexible Flash controller.

Before you reboot the server, ensure that the device you select is enabled on the Cisco Flexible Flash card.

Examples

This example shows how to specify that the server boots from the Cisco UCS Server Configuration Utility:

server# scope bios
server /bios # set boot-override SCU
server /bios* # commit
server /bios #

Related Commands

Command	Description
show bios

set cdb-wq-count

To set the number of command descriptor block (CDB) transmit queue resources to allocate, use the set cdb-wq-count command.

set cdb-wq-count count

Syntax Description

count

The number of command descriptor block (CDB) transmit queue resources to allocate. The range is 1 to 8. The default count is 1.

Command Default

The default count is 1.

Command Modes

SCSI-IO (/chassis/adapter/host-fc-if/scsi-io )

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the command descriptor block (CDB) transmit queue resources of the host Fibre Channel interface:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
server /chassis/adapter/host-fc-if # scope scsi-io
Server /chassis/adapter/host-fc-if/scsi-io # set cdb-wq-count 4
Server /chassis/adapter/host-fc-if/scsi-io *# commit
Server /chassis/adapter/host-fc-if/scsi-io #

Related Commands

Command	Description
set cdb-wq-ring-size

set cdb-wq-ring-size

To set the number of descriptors in the command descriptor block (CDB) transmit queue, use the set cdb-wq-ring-size command.

set cdb-wq-ring-size size

Syntax Description

size	The number of descriptors in the command descriptor block (CDB) transmit queue. The range is 64 to 512.

Command Default

The default descriptor number is 512.

Command Modes

SCSI-IO (/chassis/adapter/host-fc-if/scsi-io )

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the number of descriptors in the command descriptor block (CDB) transmit queue:

Server # scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # scope scsi-io
Server /chassis/adapter/host-fc-if/scsi-io # set cdb-wq-ring-size 78
Server /chassis/adapter/host-fc-if/scsi-io *# commit
Server /chassis/adapter/host-fc-if/scsi-io #

Related Commands

Command	Description
set cdb-wq-count

set channel-number

To specify the Network Interface Virtualization (NIV) channel number, use the set channel-number command.

set channel-number number

Syntax Description

number

The NIV channel number. Specify a number between 1 and 1000.

Command Default

None

Command Modes

Ethernet host interface (/chassis/adapter/host-eth-if)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Note

To use this command, you must enable NIV mode for the adapter.

Examples

This example shows how to set the NIV channel number on interface eth0 on adapter card 1:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # set niv-mode enabled
Server /chassis/adapter *# scope host-eth-if eth0
Server /chassis/adapter/host-eth-if *# set channel-number 5
Server /chassis/adapter/host-eth-if *# commit
Server /chassis/adapter/host-eth-if #

Related Commands

Command	Description
set niv-mode
show host-eth-if

set ChannelInterLeave

To specify how the CPU performs interleaving of memory blocks, use the set ChannelInterLeave command.

set ChannelInterLeave { Auto | 1_Way | 2_Way | 4_Way | 8_Way }

Syntax Description

Auto	The CPU determines what interleaving is done.
1_Way	Some channel interleaving is used.
2_Way	Additional channel interleaving is used.
4_Way	Additional channel interleaving is used.
8_Way	The maximum amount of channel interleaving is used.

Command Default

The CPU determines what interleaving is done.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(5)	This command was introduced.

Usage Guidelines

Use this command to specify how the CPU divides memory blocks and spreads contiguous portions of data across interleaved channels to enable simultaneous read operations.

Examples

This example configures the CPU to perform the maximum amount of channel interleaving and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set ChannelInterLeave 8_Way
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set chap-name

To set a target CHAP name for the iSCSI target, use the set chap-name command.

set chap-name name

Syntax Description

name	The Challenge-Handshake Authentication Protocol (CHAP) name.

Command Default

None

Command Modes

iSCSI target (/chassis/adapter/host-eth-if/iscsi-boot/iscsi-target)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

None

Examples

This example shows how to set the CHAP name for an iSCSI target:

Server # scope chassis
Server /chassis # scope adapter 3
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # scope iscsi-boot 0
Server /chassis/adapter/host-eth-if/iscsi-boot # create iscsi-target 1
Server /chassis/adapter/host-eth-if/iscsi-boot/iscsi-target* # set chap-name sample
Server /chassis/adapter/host-eth-if/iscsi-boot/iscsi-target* # commit
Server /chassis/adapter/host-eth-if/iscsi-boot/iscsi-target #

Related Commands

Command	Description
set boot-lun
set chap-secret
set ipaddr
set iqn

set chap-secret

To set a CHAP secret for the iSCSI target, use the set chap-secret command.

set chap-secret value

Syntax Description

value

The Challenge-Handshake Authentication Protocol (CHAP) shared secret of iSCSI target.

Command Default

None

Command Modes

iSCSI target (/chassis/adapter/host-eth-if/iscsi-boot/iscsi-target)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

None

Examples

This example shows how to set the CHAP secret for an iSCSI target:

Server # scope chassis
Server /chassis # scope adapter 3
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # scope iscsi-boot 0
Server /chassis/adapter/host-eth-if/iscsi-boot # create iscsi-target 1
Server /chassis/adapter/host-eth-if/iscsi-boot/iscsi-target* # set chap-secret sample
Server /chassis/adapter/host-eth-if/iscsi-boot/iscsi-target* # commit
Server /chassis/adapter/host-eth-if/iscsi-boot/iscsi-target #

Related Commands

Command	Description
set boot-lun
set chap-name
set ipaddr
set iqn

set Ck410bConfigSpreadSpectrumEnable

To enable spread spectrum clock modulation for EMI reduction, use the set Ck410bConfigSpreadSpectrumEnable command.

set Ck410bConfigSpreadSpectrumEnable { Disabled | Enabled }

Syntax Description

Disabled	The server does not use the spread spectrum function.
Enabled	The server uses the spread spectrum function.

Command Default

The server uses the spread spectrum function.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(3)	This command was introduced.

Usage Guidelines

Use this command to enable spread spectrum clock modulation. Spread Spectrum modulates the pulses produced by the clock on the motherboard in order to reduce the EMI (Electromagnetic Interference) generated by those pulses.

Examples

This example specifies that the server uses the spread spectrum function and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set Ck410bConfigSpreadSpectrumEnable Enabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description

set CkeLowPolicy

To specify the DIMM power savings mode policy, use the set CkeLowPolicy command.

set CkeLowPolicy { Auto | Disabled | Fast | Slow }

Syntax Description

Auto	The BIOS controls when a DIMM enters power saving mode based on the DIMM configuration.
Disabled	DIMMs do not enter power saving mode.
Fast	DIMMs enter power saving mode as often as possible.
Slow	DIMMs can enter power saving mode, but the requirements are higher. Therefore, DIMMs enter power saving mode less frequently.

Command Default

The BIOS controls when a DIMM enters power saving mode (Auto).

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(1)	This command was introduced.

Examples

This example specifies that DIMMs enter power saving mode as often as possible and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set CkeLowPolicy Fast
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set cli output

To change the CLI output, use the set cli output command.

set cli output { default | | yaml }

Syntax Description

cli output	Specifies server CLI output.
default	Sets CLI output to default.
yaml	Sets CLI ouput to YAML (YAML Ain't Markup Language).

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to change the CLI output to YAML:

server# set cli output yaml
CLI output format set to yaml
server#

set coalescing-time

To set the time to wait between interrupts or the idle period that must be encountered before an interrupt is sent, use the set coalescing-time command.

set coalescing-time usec

Syntax Description

usec	The time to wait between interrupts or the idle period that must be countered before an interrupt is sent. The range is 1 to 65535 microseconds; the default is 125. To turn off coalescing enter 0 (zero).

Command Default

The default is 125.

Command Modes

Interrupt (/chassis/adapter/host-eth-if/interrupt)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the coalescing time:

Server# scope chassis
Server /chassis/ # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # scope interrupt
Server /chassis/adapter/host-eth-if/interrupt # set coalescing-time 65 
Server /chassis/adapter/host-eth-if/interrupt *# commit
Committed host-eth-if eth0 settings will take effect upon the next server reset

Related Commands

Command	Description
set coalescing-type

set coalescing-type

To set the coalescing type of the host Ethernet interface, use the set coalescing-type command.

set coalescing-type { idle | min }

Syntax Description

idle	The system does not send an interrupt until there is a period of no activity lasting as least as long as the time specified in the coalescing time configuration.
min	The system waits for the time specified in the coalescing time configuration before sending another interrupt event.

Command Default

The default is min.

Command Modes

Interrupt (/chassis/adapter/host-eth-if/interrupt)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the coalescing type:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Srver /chassis/adapter/host-eth-if scope interrupt
Server /chassis/adapter/host-eth-if/interrupt # set coalescing-type idle 
Server /chassis/adapter/host-eth-if/interrupt *# commit
Committed host-eth-if eth0 settings will take effect upon the next server reset
Server /chassis/adapter/host-eth-if/interrupt #

Related Commands

Command	Description
set coalescing-time

set CoherencySupport

To specify whether the processor supports Intel VT-d Coherency, use the set CoherencySupport command.

set CoherencySupport { Disabled | Enabled }

Syntax Description

Disabled	The processor does not support coherency.
Enabled	The processor uses Intel VT-d Coherency as required.

Command Default

The processor does not support Intel VT-d Coherency.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example specifies that the processor supports VT-d Coherency and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set CoherencySupport Enabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set community-str

To specify the SNMP community name, use the set community-str command.

set community-str community

Syntax Description

community

The SNMP v1 or v2c community name or SNMP v3 username.

Command Default

None

Command Modes

SNMP (/snmp)

Command History

Release	Modification
1.3(1)	This command was introduced.
1.4(1)	This command was moved from the fault command mode.

Usage Guidelines

Use this command to specify the SNMP v1 or v2c community name or SNMP v3 username that CIMC includes on any trap messages it sends to the SNMP host. The name can be up to 18 characters.

SNMP must be enabled and saved before this command can be accepted.

Examples

This example configures the SNMP parameters and commits the transaction:

Server# scope snmp
Server /snmp # set enabled yes
Server /snmp *# commit
Server /snmp # set community-str cimcpublic
Server /snmp *# set sys-contact "User Name <username@example.com> +1-408-555-1212"
Server /snmp *# set sys-location "San Jose, California"
Server /snmp *# commit
Server /snmp #  show detail
SNMP Settings:
    SNMP Port: 161
    System Contact: User Name <username@example.com> +1-408-555-1212
    System Location: San Jose, California
    SNMP Community: cimcpublic
    SNMP Trap community: 0
    Enabled: yes
    SNMP Trap Version: 1
    SNMP Inform Type: inform

Server /snmp #

Related Commands

Command	Description
show snmp

set comport

To set the serial port through which the system routes serial over LAN (SoL) communications, use the set comport command.

Note

This field is only available on some C-Series servers. If it is not available, the server always uses COM port 0 for SoL communication.

set comport { com0 | com1 }

Syntax Description

com0

SoL communication is routed through COM port 0, an externally accessible serial port that supports either a physical RJ45 connection to an external device or a virtual SoL connection to a network device.

If you select this option, the system enables SoL and disables the RJ45 connection, which means that the server can no longer support an external serial device.

com1

SoL communication is routed through COM port 1, an internal port accessible only through SoL.

If you select this option, you can use SoL on COM port 1 and the physical RJ45 connection on COM port 0.

Command Default

None

Command Modes

Serial over LAN (/sol)

Command History

Release	Modification
1.4(6)	This command was introduced.

Usage Guidelines

Use this command to specify the COM port for serial port communications.

Note

Changing the comport setting disconnects any existing SoL sessions.

Examples

This example configures SoL communication to be routed through COM port 1 on the serial port and commits the transaction:

Server# scope sol
Server /sol # set comport com1
Server /sol *# set enabled yes
Server /sol *# commit
Server /sol #

Related Commands

Command	Description
show sol

set ConfigSATAMode

To specify the mode in which the SATA controller runs, use the set ConfigSATAMode command.

set ConfigSATAMode { AHCI | Compatibility | Enhanced | S/W_RAID }

Syntax Description

AHCI	The controller enables the Advanced Host Controller Interface (AHCI) and disables RAID.
Compatibility	The controller disables both AHCI and RAID and runs in IDE emulation mode.
Enhanced	The controller enables both AHCI and RAID.
S/W_RAID	The controller enables RAID and disables the AHCI.

Command Default

The controller enables both AHCI and RAID.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Note

This command is not available on all models and configurations.

Examples

This example specifies that the controller disables both AHCI and RAID and runs in IDE emulation mode and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set ConfigSATAMode Compatibility
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set ConsoleRedir

To allow a serial port to be used for console redirection during POST and BIOS booting, use the set ConsoleRedir command.

set ConsoleRedir { Disabled | Serial_Port_A }

Syntax Description

Disabled	No console redirection occurs during POST.
Serial_Port_A	Enables serial port A for console redirection during POST. This option is valid for blade servers and rack-mount servers.

Command Default

Disabled

Command Modes

Server Management BIOS (/bios/server-management)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Use this command to allow a serial port to be used for console redirection during POST and BIOS booting. After the BIOS has booted and the operating system is responsible for the server, console redirection is irrelevant and has no effect.

Note

By enabling this option, you also disable the display of the Quiet Boot logo screen during POST.

Examples

This example configures the BIOS to allow serial port A to be used for console redirection during POST and BIOS booting and commits the transaction:

Server# scope bios
Server /bios # scope server-management
Server /bios/server-management # set ConsoleRedir Serial_Port_A
Server /bios/server-management *# commit
Server /bios/server-management #

Related Commands

Command	Description
show server-management

set CoreMultiProcessing

To set the state of logical processor cores in a package, use the set CoreMultiProcessing command.

set CoreMultiProcessing { All | number }

Syntax Description

All	Enables multi processing on all logical processor cores.
number	The number of logical processor cores that can run on the server.

Command Default

Multi processing is enabled on all logical processor cores.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

To disable multi processing and have only one logical processor core running on the server, set number to 1. When only one logical processor core is running on the server, Hyper Threading is also disabled.

Note

We recommend that you contact your operating system vendor to make sure the operating system supports this feature.

Examples

This example specifies that two processor cores can be run on the server and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set CoreMultiProcessing 2
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set cos

To specify the CoS value to be marked by an interface, use the set cos command.

set cos cos-value

Syntax Description

cos-value

Specifies a CoS value to be marked.

Command Default

None

Command Modes

Ethernet host interface (/chassis/adapter/host-eth-if)

Fibre Channel host interface (/chassis/adapter/host-fc-if)

Command History

Release	Modification
1.2(1)	This command was introduced.

Usage Guidelines

Use this command to specify the class of service (CoS) to be marked on received packets unless the interface is configured to trust host CoS. Valid CoS values are 0 to 6; the default is 0. Higher values indicate more important traffic.

Examples

This example shows how to specify a CoS value of 5 for the Ethernet host interface eth0:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # set cos 5
Server /chassis/adapter/host-eth-if *# commit
Server /chassis/adapter/host-eth-if #

Related Commands

Command	Description
set trust-host-cos

set CpuEngPerfBias

To specify whether system performance or energy efficiency is more important on this server, use the set CpuEngPerfBias command.

set CpuEngPerfBias { Balanced_Energy | Balanced_Performance | Energy_Efficient | Performance }

Syntax Description

Balanced_Energy	Balanced, but energy efficiency is more important.
Balanced_Performance	Balanced, but performance is more important.
Energy_Efficient	Energy efficiency is most important.
Performance	Performance is most important.

Command Default

Balanced Performance

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(4)	This command was introduced.

Usage Guidelines

Note

The server ignores the setting for this command unless Power Management is set to Custom in the GUI, or the set CPUPowerManagement command is set to Custom in the CLI.

In addition, some operating systems, such as Windows 2008, ignore this parameter in favor of their own power plan.

Examples

This example specifies that energy efficiency is most important on this server and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set CpuEngPerfBias Energy_Efficient
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set CPUPowerManagement

set CpuFreqFloor

To specify whether the CPU is allowed to drop below the maximum non-turbo frequency when idle, use the set CpuFreqFloor command.

set CpuFreqFloor { Disabled | Enabled }

Syntax Description

Disabled	The CPU can drop below the maximum non-turbo frequency when idle. This option decreases power consumption but may reduce system performance.
Enabled	The CPU cannot drop below the maximum non-turbo frequency when idle. This option improves system performance but may increase power consumption.

Command Default

The CPU can drop below the maximum non-turbo frequency when idle.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(5)	This command was introduced.

Examples

This example configures the CPU to prevent dropping below the maximum non-turbo frequency when idle and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set CpuFreqFloor Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set CPUPerformance

To set the CPU performance profile for the server, use the set CPUPerformance command.

set CPUPerformance { Custom | Enterprise | HPC | High_Throughput }

Syntax Description

Custom	All performance profile options can be configured from the BIOS setup on the server.
Enterprise	Only the Data Cache Unit (DCU) IP Prefetcher is enabled. All other options are disabled.
HPC	Data Reuse Optimization is disabled and all other options are enabled. This setting is also known as high performance computing (HPC).
High_Throughput	All options are enabled.

Command Default

The processor classifies memory areas.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Use this command to set the CPU performance profile for the server. The performance profile consists of the following options:

Adjacent Cache-Line Prefetch
Data Reuse Optimization
Data Cache Unit (DCU) Streamer Prefetcher
DCU IP Prefetcher
Hardware Prefetcher

When the Custom option is selected, you can also configure the listed options using their individual commands.

Examples

This example specifies that the processor uses the Custom performance profile and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set CPUPerformance Custom
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set AdjacentCacheLinePrefetch
set DcuIpPrefetch
set DcuStreamerPrefetch
set HardwarePrefetch

set CPUPowerManagement

To configure the CPU power management settings, use the set CPUPowerManagement command.

set CPUPowerManagement { Custom | Disabled | Energy_Efficient }

Syntax Description

Custom	The server uses the individual settings for a set of BIOS parameters.
Disabled	The server performs no CPU power management.
Energy_Efficient	The server determines the best settings for CPU power management.

Command Default

The server determines the best settings for CPU power management.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(4)	This command was introduced.

Usage Guidelines

Use this command to configure the CPU power management settings for the following options:

Enhanced Intel Speedstep Technology
Intel Turbo Boost Technology
Processor Power State C6

The CPU power management setting can be one of the following:

Custom—The server uses the individual settings for the BIOS parameters mentioned above. You must select this option if you want to change any of these BIOS parameters.
Disabled—The server does not perform any CPU power management and any settings for the BIOS parameters mentioned above are ignored.
Energy_Efficient—The server determines the best settings for the BIOS parameters mentioned above and ignores the individual settings for these parameters.

Examples

This example enables the individual settings for the related BIOS parameters and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set CPUPowerManagement Custom
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set EnhancedIntelSpeedStep
set IntelTurboBoostTech
set ProcessorC6Report

set cq-count

To set the number of completion queue resources to allocate, use the set cq-count command.

set cq-count count

Syntax Description

count

The number of completion queue resources to allocate. The range is 1 to 512.

Command Default

The default count is 5.

Command Modes

Completion queue (/chassis/adapter/host-eth-if/comp-queue)

Command History

Release	Modification
1.2(1)	This command was introduced.

Usage Guidelines

In general, the number of completion queues equals the number of transmit queues plus the number of receive queues.

Examples

This example shows how to set the number of completion queue resources to allocate:

Server # scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # scope comp-queue 
Server /chassis/adapter/host-eth-if/comp-queue # set cq-count 59
Server /chassis/adapter/host-eth-if/comp-queue *# commit
Committed host-eth-if eth0 settings will take effect upon the next server reset
Server /chassis/adapter/host-eth-if/comp-queue #

Related Commands

Command	Description
show comp-queue

set dc

To specify an Active Directory domain controller, use the set dc command.

set dcn dc-host

Syntax Description

n	The index of the AD domain controller entry.
dc-host	The host name or IP address of the AD domain controller.

Command Default

None

Command Modes

LDAP (/ldap)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to specify the host name or IP address of an Active Directory (AD) domain controller (DC). CIMC can store up to three DCs for AD. Use an index number of 1 to 3 to store the server information.

Examples

This example shows how to store an AD domain controller IP address as DC number 2:

Server# scope ldap
Server /ldap # set dc2 192.0.20.123
Server /ldap* # commit
Server /ldap #

Related Commands

Command	Description
set gc
show ldap

set DcuIpPrefetch

To enable or disable the DCU IP prefetcher, use the set DcuIpPrefetch command.

set DcuIpPrefetch { Disabled | Enabled }

Syntax Description

Disabled	The DCU IP prefetcher is disabled.
Enabled	The DCU IP prefetcher is enabled.

Command Default

The DCU IP prefetcher is enabled.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(4)	This command was introduced.

Usage Guidelines

Use this command to specify whether the processor uses the Data Cache Unit (DCU) Instruction Pointer-based (IP) Prefetch mechanism to analyze historical cache access patterns and preload the most relevant lines in the L1 cache. This can be one of the following:

Disabled—The processor does not preload any cache data.
Enabled—The DCU IP prefetcher preloads the L1 cache with the data it determines to be the most relevant.

Examples

This example enables the DCU IP prefetcher and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set DcuIpPrefetch Enabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set CPUPerformance
set DcuStreamerPrefetch

set DcuStreamerPrefetch

To specify whether the processor uses the Data Cache Unit (DCU) Prefetch mechanism, use the set DcuStreamerPrefetch command.

set DcuStreamerPrefetch { Disabled | Enabled }

Syntax Description

Disabled	The DCU Prefetch mechanism is disabled.
Enabled	The DCU Prefetch mechanism is enabled.

Command Default

The DCU Prefetch mechanism is enabled.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(4)	This command was introduced.

Usage Guidelines

Use this command to specify whether the processor uses the Data Cache Unit (DCU) Prefetch mechanism to determine if the processor should fetch the next line in the L1 cache before the line is actually requested. This can be one of the following:

Disabled—The processor does not try to anticipate cache read requirements and only fetches explicitly requested lines.
Enabled—The DCU prefetcher analyzes the cache read pattern and prefetches the next line in the cache if it determines that it may be needed.

Examples

This example enables the DCU Prefetch mechanism and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set DcuStreamerPrefetch Enabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set CPUPerformance
set DcuIpPrefetch

set delay

To specify whether server power is restored after a fixed or random time, use the set delay command.

set delay { fixed | random }

Syntax Description

fixed	Server power is restored after a fixed time.
random	Server power is restored after a random time.

Command Default

Server power is restored after a fixed time.

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Use this command to specify whether server power is restored after a fixed or random time after an outage.

When the selected action is fixed, the delay time is configured by the set delay-value command.

Examples

This example sets the power restore policy to power-on with a fixed delay of 180 seconds (3 minutes) and commits the transaction:

Server# scope chassis
Server /chassis # set policy power-on
Server /chassis *# set delay fixed
Server /chassis *# set delay-value 180
Server /chassis *# commit
Server /chassis #  show detail
Chassis:
    Power: on
    Serial Number: QCI1404A1IT
    Product Name: UCS C200 M1
    PID : R200-1120402
    UUID: 01A6E738-D8FE-DE11-76AE-8843E138AE04
    Locator LED: off
    Description: Testing power restore
    Power Restore Policy: power-on
    Power Delay Type: fixed
    Power Delay Value(sec): 180

Server /chassis #

Related Commands

Command	Description
set policy
set delay-value

set delay-value

To specify the delay time for restoring server power after an outage, use the set delay-value command.

set delay-value delay

Syntax Description

delay

The delay time in seconds.

Command Default

The default delay is 0 seconds.

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Use this command to specify the delay time in seconds for restoring server power after an outage. The range is 0 to 240; the default is 0.

This command is operative only when the power restore policy is power-on with a fixed delay.

Examples

This example sets the power restore policy to power-on with a fixed delay of 180 seconds (3 minutes) and commits the transaction:

Server# scope chassis
Server /chassis # set policy power-on
Server /chassis *# set delay fixed
Server /chassis *# set delay-value 180
Server /chassis *# commit
Server /chassis #  show detail
Chassis:
    Power: on
    Serial Number: QCI1404A1IT
    Product Name: UCS C200 M1
    PID : R200-1120402
    UUID: 01A6E738-D8FE-DE11-76AE-8843E138AE04
    Locator LED: off
    Description: Testing power restore
    Power Restore Policy: power-on
    Power Delay Type: fixed
    Power Delay Value(sec): 180

Server /chassis #

Related Commands

Command	Description
set policy
set delay

set DemandScrub

To specify whether the system corrects single bit memory errors encountered when the CPU or I/O makes a demand read, use the set DemandScrub command.

set DemandScrub { Disabled | Enabled }

Syntax Description

Disabled	Single bit memory errors are not corrected.
Enabled	Single bit memory errors are corrected in memory and the corrected data is set in response to the demand read.

Command Default

Single bit memory errors are corrected.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(5)	This command was introduced.

Examples

This example disables single bit memory errors and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set DemandScrub Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set description (chassis)

To set up a description for the chassis, use the set description command in chassis mode.

set description chassis-description

Syntax Description

chassis-description

The description of the chassis. The range of valid values is 1 to 64.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to :

server# scope chassis
server /chassis # set description testServer
server /chassis* # commit
server /chassis #

Related Commands

Command	Description
show chassis

set dhcp-enabled

To specify whether the CIMC uses DHCP to obtain an IP address, use the set dhcp-enabled command.

set dhcp-enabled { no | yes }

Syntax Description

no	The CIMC does not use DHCP to obtain an IP address.
yes	The CIMC uses DHCP to obtain an IP address.

Command Default

The CIMC does not use DHCP to obtain an IP address.

Command Modes

Network (/cimc/network)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Note

If DHCP is enabled, we recommend that the DHCP server be configured to reserve a single IP address for the CIMC. If the CIMC is reachable through multiple ports on the server, the single IP address must be reserved for the full range of MAC addresses of those ports.

Examples

This example specifies that the CIMC uses DHCP to obtain an IP address:

server# scope cimc
server /cimc # scope network
server /cimc/network # set dhcp-enabled yes
server /cimc/network* # commit
server /cimc/network #

Related Commands

Command	Description
show network

set dhcp-id

To set the DHCP ID for the iSCSI boot target, use the set dhcp-id command.

set dhcp-id value

Syntax Description

value

IP address of the DHCP server. Enter a string up to 64 characters.

Command Default

None

Command Modes

iSCSI boot (chassis/adapter/host-eth-if/iscsi-boot)

Command History

Release	Modification
1.5(1)	The command was introduced.

Usage Guidelines

To set the DHCP ID, an iSCSI boot target for a vNIC must be created.

Examples

This example shows how to set the DHCP IP address for an iSCSI boot target for a vNIC:

 
server# scope chassis
server /chassis # scope adapter 1
server /chassis/adapter # scope host-eth-if eth0
server /chassis/adapter/host-eth-if # create iscsi-boot 0
server /chassis/adapter/host-eth-if/iscsi-boot*# set dhcp-id 1.2.3.4
server /chassis/adapter/host-eth-if/iscsi-boot*# commit
server /chassis/adapter/host-eth-if/iscsi-boot #

Related Commands

Command	Description
set dhcp-iscsi-settings
set dhcp-net-settings
set dhcp-timeout

set dhcp-iscsi-settings

To enable or disable DHCP iSCSI settings, use the set dhcp-iscsi-settings command.

set dhcp-iscsi-settings enable disable

Syntax Description

enable	Enables the DHCP settings.
disable	Disables the DHCP settings.

Command Default

None

Command Modes

iSCSI boot (chassis/adapter/host-eth-if/iscsi-boot)

Command History

Release	Modification
1.5(1)	The command was introduced.

Usage Guidelines

To enable or disable DHCP settings, an iSCSI boot target for a vNIC must be created.

Examples

This example shows how to enable DHCP settings:

server# scope chassis
server /chassis # scope adapter 1
server /chassis/adapter # scope host-eth-if eth0
server /chassis/adapter/host-eth-if # create iscsi-boot 0
server /chassis/adapter/host-eth-if/iscsi-boot*# set dhcp-iscsi-settings enable
server /chassis/adapter/host-eth-if/iscsi-boot*# commit
server /chassis/adapter/host-eth-if/iscsi-boot #

Related Commands

Command	Description
set dhcp-id
set dhcp-net-settings
set dhcp-timeout

set dhcp-net-settings

To enable or disable DHCP network settings, use the set dhcp-net-settings command.

set dhcp-net-settings enable disable

Syntax Description

enable	Enables the DHCP network settings.
disable	Disables the DHCP network settings.

Command Default

None

Command Modes

iSCSI boot (chassis/adapter/host-eth-if/iscsi-boot)

Command History

Release	Modification
1.5(1)	The command was introduced.

Usage Guidelines

To enable or disable DHCP network settings, an iSCSI boot target for a vNIC must be created.

Examples

This example shows how to enable DHCP network settings:

server # scope chassis
server /chassis # scope adapter 1
server /chassis/adapter # scope host-eth-if eth0
server /chassis/adapter/host-eth-if # create iscsi-boot 0
server /chassis/adapter/host-eth-if/iscsi-boot*# set dhcp-net-settings enable
server /chassis/adapter/host-eth-if/iscsi-boot*# commit
server /chassis/adapter/host-eth-if/iscsi-boot #

Related Commands

Command	Description
set dhcp-id
set dhcp-iscsi-settings
set dhcp-timeout

set dhcp-timeout

To set the number of seconds to wait before the initiator assumes that the link is unavailable, use the set dhcp-timeout command.

set dhcp-timeout value

Syntax Description

value

Time, in seconds for the initiator to wait. Enter an integer between 60 and 300.

Command Default

The default time is 15 seconds.

Command Modes

iSCSI boot (chassis/adapter/host-eth-if/iscsi-boot)

Command History

Release	Modification
1.5(1)	The command was introduced.

Usage Guidelines

An iSCSI boot target for a vNIC must be created before you use this command.

Examples

This example shows how to set the DHCP timeout:

server# scope chassis
server /chassis # scope adapter 1
server /chassis/adapter # scope host-eth-if eth0
server /chassis/adapter/host-eth-if # create iscsi-boot 0
server /chassis/adapter/host-eth-if/iscsi-boot*# set dhcp-timeout 60
 server /chassis/adapter/host-eth-if/iscsi-boot*# commit
server /chassis/adapter/host-eth-if/iscsi-boot #

Related Commands

Command	Description
set dhcp-id
set dhcp-iscsi-settings
set dhcp-net-settings

set DirectCacheAccess

To specify whether the processor can increase I/O performance by placing data from I/O devices directly into the processor cache, use the set DirectCacheAccess command.

set DirectCacheAccess { Disabled | Enabled }

Syntax Description

Disabled	Data from I/O devices is not placed directly into the processor cache.
Enabled	Data from I/O devices is placed directly into the processor cache.

Command Default

Data from I/O devices is placed directly into the processor cache.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example specifies that the processor does not place data from I/O devices directly into the processor cache and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set DirectCacheAccess Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set DisableSCU

To specify whether the onboard software RAID controller is available to the server, use the set DisableSCU command.

set DisableSCU { Disabled | Enabled }

Syntax Description

Disabled	The software RAID controller is not available.
Enabled	The software RAID controller is available.

Command Default

The software RAID controller is not available.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(5)	This command was introduced.

Examples

This example specifies that the onboard software RAID controller is available to the server and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set DisableSCU Enabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set dns-use-dhcp

To specify whether the CIMC uses DHCP to obtain DNS server addresses, use the set dns-use-dhcp command.

set dns-use-dhcp { no | yes }

Syntax Description

no	The CIMC does not use DHCP to obtain DNS server addresses.
yes	The CIMC uses DHCP to obtain DNS server addresses.

Command Default

The CIMC does not use DHCP to obtain DNS server addresses.

Command Modes

Network (/cimc/network)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Note

If DHCP is enabled, we recommend that the DHCP server be configured to reserve a single IP address for the CIMC. If the CIMC is reachable through multiple ports on the server, the single IP address must be reserved for the full range of MAC addresses of those ports.

Examples

This example specifies that the CIMC uses DHCP to obtain DNS server addresses:

server# scope cimc
server /cimc # scope network
server /cimc/network # set dns-use-dhcp yes
server /cimc/network* # commit
server /cimc/network #

Related Commands

Command	Description
show network

set domain

To specify the Active Directory domain for an authorization group, use the set domain command.

set domain domain-name

Syntax Description

domain-name

The Active Directory domain in which the group must reside.

Command Default

None

Command Modes

LDAP role group (/ldap/role-group)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to specify the Active Directory (AD) domain for an authorization group.

Examples

This example configures the domain name and other settings for an AD authorization group:

Server# scope ldap
Server /ldap # set group-auth yes
Server /ldap *# scope role-group 5
Server /ldap/role-group *# set name Training
Server /ldap/role-group *# set domain example.com
Server /ldap/role-group *# set role readonly
Server /ldap/role-group *# commit
Server /ldap/role-group #

Related Commands

Command	Description
scope role-group

set enabled

To enable or disable functions and actions on the server, use the set enabled command.

set enabled { no | yes }

Syntax Description

no	Disables the function or action.
yes	Enables the function or action.

Command Default

See the Usage Guidelines.

Command Modes

CIMC log server (/cimc/log/server)

HTTP (/http)

IP blocking (/cimc/chassis/ipblocking)

IPMI (/ipmi)

Keyboard Video Mouse (/kvm)

LDAP (/ldap)

NTP (/cimc/network/ntp)

Secure shell (/ssh)

Serial over LAN (/sol)

Trap destination (/fault/trap-destination)

User (/user)

Virtual media (/vmedia)

XML API (/xmlapi)

Command History

Release	Modification
1.0(1)	This command was introduced.
1.1(2)	This command was introduced for the CIMC log server command mode.
1.4(1)	This command was introduced for the XML API command mode.
1.5(1)	This command was introduced for the NTP command mode.

Usage Guidelines

Use this command to enable or disable a function or action. For the supported command modes, the following actions are enabled when yes is selected:

CIMC log server — Enables the sending of CIMC log entries to a remote syslog server. The default is disabled.
HTTP — Enables HTTP services on the server. The default is enabled.
IP blocking — Enables the blocking of login after several failed attempts. The default is disabled.
IPMI — Enables IPMI on the server. The default is enabled.
Keyboard Video Mouse — Enables KVM connections to CIMC. The default is enabled.
LDAP — Enables IPMI services on the server. The default is disabled.
NTP — Enables NTP on the server. The default is disabled.
Secure shell — Enables SSH services on the server. The default is enabled.
Serial over LAN — Enables SoL on the server. The default is disabled.
Trap destination — Enables SNMP trap destination services. The default is disabled.
User — Enables the user account.
Virtual media — Enables virtual media services on the server. The default is enabled.
XML API — Enables XML API access to CIMC on the server.

Examples

This example shows how to configure a remote syslog server profile and enable the sending of CIMC log entries:

server# scope cimc
server /cimc # scope log
server /cimc/log # scope server 2
server /cimc/log/server # set server-ip 192.0.2.34
server /cimc/log/server *# set enabled yes
server /cimc/log/server *# commit
server /cimc/log/server #

Related Commands

Command	Description

set encrypted

To enable or disable the encryption of information, use the set encrypted command.

set encrypted { no | | yes }

Syntax Description

no	Information is not encrypted.
yes	Information is encrypted.

Command Default

Video information sent through the KVM is not encrypted.

The Active Directory is not encrypted.

Virtual media data is not encrypted.

Command Modes

KVM (/kvm)

LDAP (/ldap)

Virtual media (/vmedia)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to enable or disable the encryption of data in the following command modes:

KVM command mode — Enables or disables the encryption of video information sent through the KVM.
LDAP command mode — Enables or disables the encryption of the Active Directory.
Virtual media command mode — Enables or disables the encryption of virtual media data.

Examples

This example enables the encryption of video information sent through the KVM:

server# scope kvm
server /kvm # set enabled yes
server /kvm* # set encrypted yes
server /kvm* # commit
server /kvm #

Related Commands

Command	Description
show kvm
show ldap
show vmedia

set encryption-key

To specify the encryption key for IPMI communications, use the set encryption-key command.

set encryption-key encryption-key

Syntax Description

encryption-key

The encryption key for IPMI communications. The key value must be 40 hexadecimal numbers.

Command Default

None

Command Modes

IPMI (/ipmi)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to set the IPMI encryption key:

server# scope ipmi
server /ipmi # set enabled yes
server /ipmi* # set encryption-key a9 62 b5 0a 68 6e e3 02 72 ce af f1 39 f8 1e 05 f5 
19 d5 e1 7f f4 71 b9 9a 41 be e3 f5 06 4e cc 0f 63 67 2e a2 9c 74 d0
server /ipmi* # commit
server /ipmi #

Related Commands

Command	Description
show ipmi

set EnhancedIntelSpeedStep

To specify whether the processor uses Enhanced Intel SpeedStep Technology, use the set EnhancedIntelSpeedStep command.

set EnhancedIntelSpeedStep { Disabled | Enabled }

Syntax Description

Disabled	The processor never dynamically adjusts its voltage or frequency.
Enabled	The processor uses Enhanced Intel SpeedStep Technology if required.

Command Default

The processor uses Enhanced Intel SpeedStep Technology if required.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Enhanced Intel SpeedStep Technology allows the system to dynamically adjust the processor voltage and core frequency. This technology can result in decreased average power consumption and decreased average heat production.

We recommend that you contact your operating system vendor to make sure the operating system supports this feature.

Note

The server ignores the setting for this command unless Power Management is set to Custom in the GUI, or the set CPUPowerManagement command is set to Custom in the CLI.

Examples

This example specifies that the processor never dynamically adjusts its voltage or frequency and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set EnhancedIntelSpeedStep Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set CPUPowerManagement

set error-count-threshold

To specify the number of errors that can occur before CIMC decides that the Cisco Flexible Flash card has failed, use the set error-count-threshold command.

set error-count-threshold count

Syntax Description

count

Enter a number between 0 and 255.

Command Default

Command Modes

FlexFlash operational profile (/chassis/flexflash/operational-profile)

Command History

Release

Modification

1.3(3)

This command was introduced.

1.5(1)

This command is no longer available. This command has been replaced with following commands:

set write-error-count-threshold
set read-error-count-threshold

Usage Guidelines

Use this command to specify the number of errors that can occur before CIMC decides that the Cisco Flexible Flash card has failed. Once this threshold has been reached, you must reset the Cisco Flexible Flash card before CIMC attempts to access it again.

Enter an integer between 1 and 255, or enter 0 (zero) if you want CIMC to continue using the card no matter how many errors it encounters.

Examples

This example shows how to set the error count threshold to 100 for the first flash device:

Server# scope chassis
Server /chassis # scope flexflash FlexFlash-0
Server /chassis/flexflash # scope operational-profile
Server /chassis/flexflash/operational-profile # set error-count-threshold 100
Server /chassis/flexflash/operational-profile *# commit
Server /chassis/flexflash/operational-profile #

Related Commands

Command	Description
scope operational-profile

set error-detect-timeout

To set the error detection timeout value (EDTOV), use the set error-detect-timeout command.

set error-detect-timeout msec

Syntax Description

msec	Specifies the error detect timeout value (EDTOV), the number of milliseconds to wait before the system assumes that an error has occurred. The range is 1000 to 100000; the default is 2000 milliseconds.

Command Default

The default is 2000 milliseconds.

Command Modes

Fibre Channel host interface (/chassis/adapter/host-fc-if)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the error detection timeout value to 5000 milliseconds:

Server# scope chassis
Server /chassis/ # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0 
Server /chassis/adapter/host-fc-if # set error-detect-timeout 5000
Server /chassis/adapter/host-fc-if *# commit
Server /chassis/adapter/host-fc-if #

Related Commands

Command	Description
set resource-allocation-timeout

set ExecuteDisable

To classify memory areas on the server to specify where application code can execute, use the set ExecuteDisable command.

set ExecuteDisable { Disabled | Enabled }

Syntax Description

Disabled	The processor does not classify memory areas.
Enabled	The processor classifies memory areas.

Command Default

The processor classifies memory areas.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

By using memory classification, the processor disables code execution if a malicious worm attempts to insert code in the buffer. This setting helps to prevent damage, worm propagation, and certain classes of malicious buffer overflow attacks.

Note

We recommend that you contact your operating system vendor to make sure the operating system supports this feature.

Examples

This example specifies that the processor does not classify memory and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set ExecuteDisable Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set fan-policy

To set a fan policy for a server, use the set fan-policy command.

set fan-policy { balanced | performance | low-power | high-power | maximum-power }

Syntax Description

balanced	Cools almost any server configuration, but may not be suitable for servers with PCIe cards, since these cards overheat easily.
performance	For server configurations where maximum fan speed is required for high performance. With this setting, the fan will run at the same speed or higher speed than that of the Balanced fan policy.
low-power	This setting is ideal for minimal configuration servers that do not contain any PCIe cards.
high-power	For server configurations that require fan speeds ranging from 60% to 85%. This policy is ideal for servers that contain PCIe cards that easily overheat and have high temperatures. The minimum fan speed set with this policy varies for each server platform, but is approximately in the range of 60 to 85%.
maximum-power	For server configurations that require extremely high fan speeds ranging from 70% to 100%. This policy is ideal for servers that contain PCIe cards that easily overheat and have extremely high temperatures. This policy is ideal for servers that contain PCIe cards that easily overheat and have extremely high temperatures. The minimum fan speed set with this policy varies for each server platform, but is approximately in the range of 70 to 100%.

Command Default

The default fan policy is balanced.

Command Modes

Fan policy (/chassis/fan-policy)

Command History

Release	Modification
1.5(2)	This command was introduced.

Usage Guidelines

Determine the server components prior to changing the fan policy. If your server configuration includes PCIe cards that overheat easily, then you must set a policy that allows for higher fan speed.

Examples

This example shows how to set the fan policy to maximum power for a chassis:

server # scope chassis
server /chassis # scope fan-policy
server /chassis/fan-policy # set fan-policy maximum-power
server /chassis/fan-policy* # commit
server /chassis/fan-policy #

Related Commands

Command	Description
scope fan-policy
show fan-policy

set fail-count

To specify a limit on the number of unsuccessful login attempts, use the set fail-count command.

set fail-count fail-count

Syntax Description

fail-count

The number of times a user can attempt to log in unsuccessfully before the system locks that user out for a specified length of time. The range of valid values is 3 to 10.

Command Default

The default failure count is 5 attempts.

Command Modes

IP blocking (/cimc/network/ipblocking)

Command History

Release	Modification
1.0(1X)	This command was introduced.

Usage Guidelines

The number of unsuccessful login attempts must occur within the time frame specified in the IP Blocking Fail Window setting.

Examples

This example sets the IP blocking failure count to 3 attempts:

server# scope cimc
server /cimc # scope network
server /cimc/network # scope ipblocking
server /cimc/network/ipblocking # set enable yes
server /cimc/network/ipblocking* # set fail-count 3
server /cimc/network/ipblocking* # commit
server /cimc/network/ipblocking #

Related Commands

Command	Description
set fail-window
show ipblocking

set fail-window

To specify a time window for unsuccessful login attempts, use the set fail-window command.

set fail-window fail-window

Syntax Description

fail-window

The length of time, in seconds, in which the unsuccessful login attempts must occur in order for the user to be locked out. The range of valid values is 60 to 120.

Command Default

The default failure window is 60 seconds.

Command Modes

IP blocking (/cimc/network/ipblocking)

Command History

Release	Modification
1.0(1X)	This command was introduced.

Examples

This example sets the IP blocking failure window to 90 seconds:

server# scope cimc
server /cimc # scope network
server /cimc/network # scope ipblocking
server /cimc/network/ipblocking # set enable yes
server /cimc/network/ipblocking* # set fail-window 90
server /cimc/network/ipblocking* # commit
server /cimc/network/ipblocking #

Related Commands

Command	Description
set fail-count
show ipblocking

set fc-rq-ring-size

To specify the receive queue ring size for the Fibre Channel interface, use the set fc-rq-ring-size command.

set fc-rq-ring-size size

Syntax Description

size	The Fibre Channel receive queue ring size. Specify a number between 64 and 128.

Command Default

The receive queue ring size is 64.

Command Modes

Fibre Channel receive queue (/chassis/adapter/host-fc-if/recv-queue)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example shows how to set the receive queue ring size to 128 on interface fc0 on adapter card 1:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # scope recv-queue
Server /chassis/adapter/host-fc-if/recv-queue # set fc-rq-ring-size 128
Server /chassis/adapter/host-fc-if/recv-queue *# commit
Server /chassis/adapter/host-fc-if/recv-queue #

Related Commands

Command	Description
show recv-queue

set fc-wq-ring-size

To specify the transmit queue ring size for the Fibre Channel interface, use the set fc-wq-ring-size command.

set fc-wq-ring-size size

Syntax Description

size	The Fibre Channel transmit queue ring size. Specify a number between 64 and 128.

Command Default

The transmit queue ring size is 64.

Command Modes

Fibre Channel transmit queue (/chassis/adapter/host-fc-if/trans-queue)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example shows how to set the transmit queue ring size to 128 on interface fc0 on adapter card 1:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # scope trans-queue
Server /chassis/adapter/host-fc-if/trans-queue # set fc-wq-ring-size 128
Server /chassis/adapter/host-fc-if/trans-queue *# commit
Server /chassis/adapter/host-fc-if/trans-queue #

Related Commands

Command	Description
show trans-queue

set fcp-error-recovery

To set the FCP Error Recovery, use the set fcp-error-recovery command.

set fcp-error-recovery { disable | enable }

Syntax Description

disable	Disables FCP Error Recovery.
enable	Enables FCP Error Recovery.

Command Default

The default is disable.

Command Modes

Error-recovery (/chassis/adapter/host-fc-if/error-recovery)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the FCP-error recovery:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # scope error-recovery
Server /chassis/adapter/host-fc-if/error-recovery # set fcp-error-recovery enable
Server /chassis/adapter/host-fc-if/error-recovery *# commit
Committed host-fc-if fc0 settings will take effect upon the next server reset
Server /chassis/adapter/host-fc-if/error-recovery #

Related Commands

Command	Description
set link-down-timeout
set port-down-io-retry-count

set fip-mode

To enable or disable FCoE Initialization Protocol (FIP) on the adapter card, use the set fip-mode command.

set fip-mode { disabled | enabled }

Syntax Description

disabled	Disables FIP mode on the card.
enabled	Enables FIP mode on the card.

Command Default

FIP mode is enabled.

Command Modes

Adapter (/chassis/adapter)

Command History

Release	Modification
1.2(1)	This command was introduced.

Usage Guidelines

Note

Note: We recommend that you disable this option only when explicitly directed to do so by a technical support representative.

Examples

This example shows how to enable FIP mode on adapter card 1:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # set fip-mode enabled
Server /chassis/adapter *# commit
Server /chassis/adapter #

Related Commands

Command	Description
show adapter detail

set flogi-retries

To specify the fabric login (FLOGI) retries value, use the set flogi-retries command.

set flogi-retries { infinite | count }

Syntax Description

infinite	Specifies infinite FLOGI retries.
count	Specifies the number of FLOGI retries. Enter a number between 0 and 4294967295.

Command Default

The default is infinite retries.

Command Modes

Port-f-logi (/chassis/adapter/host-fc-if/port-f-logi)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the fabric login retries:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # scope port-f-logi
Server /chassis/adapter/host-fc-if/port-f-logi # set flogi-retries 4294967295
Server /chassis/adapter/host-fc-if/port-f-logi *# commit
Server /chassis/adapter/host-fc-if/port-f-logi #

Related Commands

Command	Description
set flogi-timeout

set flogi-timeout

To set the fabric login (FLOGI) timeout value, use the set flogi-timeout command.

set flogi-timeout msec

Syntax Description

msec	The number of milliseconds that the system waits before it tries to log in again. The range is 1 to 255000.

Command Default

The default msec value is 2000 milliseconds.

Command Modes

Port-f-logi (/chassis/adapter/host-fc-if/port-f-logi)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the fabric login timeout:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # scope port-f-logi
Server /chassis/adapter/host-fc-if/port-f-logi # set flogi-timeout 10003
Server /chassis/adapter/host-fc-if/port-f-logi *# commit
Server /chassis/adapter/host-fc-if/port-f-logi #

Related Commands

Command	Description
set flogi-retries

set FlowCtrl

To specify whether a handshake protocol is used for flow control, use the set FlowCtrl command.

set FlowCtrl { None | RTS-CTS }

Syntax Description

None	No flow control is used.
RTS-CTS	RTS/CTS is used for flow control.

Command Default

No flow control is used.

Command Modes

Server Management BIOS (/bios/server-management)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Use this command to specify whether a handshake protocol is used for flow control. Request to Send / Clear to Send (RTS/CTS) helps to reduce frame collisions that can be introduced by a hidden terminal problem.

Note

This setting must match the setting on the remote terminal application.

Examples

This example configures the BIOS to use RTS/CTS protocol for flow control and commits the transaction:

Server# scope bios
Server /bios # scope server-management
Server /bios/server-management # set FlowCtrl RTS-CTS
Server /bios/server-management *# commit
Server /bios/server-management #

Related Commands

Command	Description
show server-management

set FRB-2

To specify whether the FRB2 timer is used by CIMC to recover the system if it halts during POST, use the set FRB-2 command.

set FRB-2 { Disabled | Enabled }

Syntax Description

Disabled	The FRB2 timer is not used.
Enabled	The FRB2 timer is started during POST and used to recover the system if necessary.

Command Default

The FRB2 timer is started during POST and used to recover the system if necessary.

Command Modes

Server Management BIOS (/bios/server-management)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Use this command to specify whether the Fault Resilient Booting (FRB) level 2 timer is used by CIMC to recover the system from a watchdog timeout during power-on self test (POST).

Examples

This example configures the BIOS to not use the FRB2 timer to recover if a watchdog timeout occurs during POST, and commits the transaction:

Server# scope bios
Server /bios # scope server-management
Server /bios/server-management # set FRB-2 Disabled
Server /bios/server-management *# commit
Server /bios/server-management #

Related Commands

Command	Description
show server-management

set gc

To specify an Active Directory global catalog server, use the set gc command.

set gcn gc-host

Syntax Description

n	The index of the AD global catalog server entry.
gc-host	The host name or IP address of the AD global catalog server.

Command Default

None

Command Modes

LDAP (/ldap)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to specify the host name or IP address of an Active Directory (AD) global catalog (GC) server. CIMC can store up to three GC servers for AD. Use an index number of 1 to 3 to store the server information.

Examples

This example shows how to store an AD global catalog server IP address as GC server number 2:

Server# scope ldap
Server /ldap # set gc2 192.0.20.11
Server /ldap* # commit
Server /ldap #

Related Commands

Command	Description
set dc
show ldap

set group-auth

To enable Active Directory authorization groups, use the set group-auth command.

set group-auth { yes | no }

Syntax Description

yes	AD authorization groups are enabled.
no	AD authorization groups are disabled.

Command Default

AD authorization groups are disabled.

Command Modes

LDAP (/ldap)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to enable Active Directory (AD) authorization groups. When AD groups are enabled, user authentication is also done on the group level for users who are not found in the local user database or who are not individually authorized to use CIMC in the Active Directory.

Examples

This example shows how to enable AD authorization groups:

Server# scope ldap
Server /ldap # set group-auth yes
Server /ldap* # commit
Server /ldap #

Related Commands

Command	Description
scope role-group

set HardwarePrefetch

To specify whether the processor uses the Intel hardware prefetcher, use the set HardwarePrefetch command.

set HardwarePrefetch { Disabled | Enabled }

Syntax Description

Disabled	The hardware prefetcher is not used.
Enabled	The hardware prefetcher is used when cache issues are detected.

Command Default

The hardware prefetcher is used when cache issues are detected.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Use this command to specify whether the processor uses the Intel hardware prefetcher to fetch streams of data and instruction from memory into the unified second-level cache when necessary.

You must select the Custom option in the set CPUPerformance command in order to specify this value. For any value other than Custom, this setting is overridden by the setting in the selected CPU performance profile.

Examples

This example specifies that the processor uses the hardware prefetcher when necessary and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set CPUPerformance Custom
Server /bios/advanced # set HardwarePrefetch Enable
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set CPUPerformance
show advanced

set hostname

To specify the host name of the server, use the set hostname command.

set hostname host-name

Syntax Description

host-name

The host name of the server. The host name can contain up to 63 characters, and will be used as the CLI prompt.

Command Default

None

Command Modes

Network (/cimc/network)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example sets the host name of the server to SanJose:

server# scope cimc
server /cimc # scope network
server /cimc/network # set hostname SanJose
server /cimc/network* # commit
SanJose /cimc/network #

Related Commands

Command	Description
show network

set http-port

To set the port number for Hyper Text Transfer Protocol (HTTP) services on the server, use the set http-port command.

set http-port port-number

Syntax Description

port-number

The HTTP port number of the server. The range of valid values is 1 to 65536.

Command Default

The default HTTP port number is 80.

Command Modes

HTTP (/http)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to set the HTTP port number to 8080:

Server# scope http
Server /http # set http-port 8080
Server /http* # commit
Server /http #

Related Commands

Command	Description
show http-port
show https-port

set http-redirect

To redirect HTTP requests to HTTPS on the server, use the set http-redirect command.

set http-redirect { yes | no }

Syntax Description

yes	HTTP requests are redirected to HTTPS.
no	HTTP requests are not redirected to HTTPS.

Command Default

HTTP requests are redirected to HTTPS.

Command Modes

HTTP (/http)

Command History

Release	Modification
1.4(1)	This command was introduced.

Examples

This example shows how to redirect HTTP requests to HTTPS on the server:

Server# scope http
Server /http # set http-redirect yes
Server /http* # commit
Server /http #

Related Commands

Command	Description
set https-port

set https-port

To set the port number for Hyper Text Transfer Protocol (HTTPS) services on the server, use the set https-port command in http mode.

set https-port port-number

Syntax Description

port-number

The HTTPS port number of the server. The range of valid values is 1 to 65536.

Command Default

The default port number is 443.

Command Modes

HTTP (/http)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to set the HTTPS port number:

server# scope http
server /http # set https-port 443
server /http* # commit
server /http #

Related Commands

Command	Description

set inform-type

To specify whether SNMP notification messages are sent as simple traps or as inform requests, use the set inform-type command.

set inform-type { inform | trap }

Syntax Description

inform	SNMP notification messages are sent as inform requests.
trap	SNMP notification messages are sent as simple traps.

Command Default

SNMP notification messages are sent as simple traps.

Command Modes

SNMP (/snmp)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to specify whether SNMP notification messages are sent as simple traps or as inform requests requiring acknowledgment by the receiver.

SNMP must be enabled and saved before this command can be accepted.

Examples

This example specifies that notifications are sent as inform requests and commits the transaction:

scope snmp
Server /snmp # set enabled yes
Server /snmp *# commit
Server /snmp # set inform-type inform
Server /snmp *# commit
Server /snmp #  show detail
SNMP Settings:
    SNMP Port: 161
    System Contact: 
    System Location: 
    SNMP Community: 
    SNMP Trap community: public-trap
    Enabled: yes
    SNMP Trap Version: 1
    SNMP Inform Type: inform

Server /snmp #

Related Commands

Command	Description
show snmp

set initiator-chap-name

To set the CHAP name of the initiator, use the set initiator-chap-name command.

set initiator-chap-name value

Syntax Description

value

The CHAP name of the initiator. The name can include a maximum of 223 characters.

Command Default

None

Command Modes

iSCSI boot (chassis/adapter/host-eth-if/iscsi-boot)

Command History

Release	Modification
1.5(1)	The command was introduced.

Usage Guidelines

To set the CHAP name of the initiator, an iSCSI boot target for a vNIC must be created.

Examples

This example shows how to set the CHAP name of the initiator:

server# scope chassis
server /chassis # scope adapter 1
server /chassis/adapter # scope host-eth-if eth0
server /chassis/adapter/host-eth-if # create iscsi-boot 0
server /chassis/adapter/host-eth-if/iscsi-boot*# set initiator-chap-name test
server /chassis/adapter/host-eth-if/iscsi-boot*# commit
server /chassis/adapter/host-eth-if/iscsi-boot #

Related Commands

Command	Description
set initiator-chap-secret
set initiator-gateway
set initiator-ipaddr
set initiator-name
set initiator-primary-dns
set initiator-secondary-dns
set initiator-subnet-mask
set initiator-tcp-timeout

set initiator-chap-secret

To set the CHAP shared secret of the initiator, use the set initiator-chap-secret command.

set initiator-chap-secret value

Syntax Description

value

The CHAP shared secret of the initiator. The name can include a maximum of 223 characters.

Command Default

None

Command Modes

iSCSI boot (chassis/adapter/host-eth-if/iscsi-boot)

Command History

Release	Modification
1.5(1)	The command was introduced.

Usage Guidelines

To set the CHAP shared secret of the initiator, an iSCSI boot target for a vNIC must be created.

Examples

This example shows how to set the CHAP shared secret of the initiator:

server# scope chassis
server /chassis # scope adapter 1
server /chassis/adapter # scope host-eth-if eth0
server /chassis/adapter/host-eth-if # create iscsi-boot 0
server /chassis/adapter/host-eth-if/iscsi-boot*# set initiator-chap-secret test
server /chassis/adapter/host-eth-if/iscsi-boot*# commit
server /chassis/adapter/host-eth-if/iscsi-boot #

Related Commands

Command	Description
set initiator-chap-name
set initiator-gateway
set initiator-ipaddr
set initiator-name
set initiator-primary-dns
set initiator-secondary-dns
set initiator-subnet-mask
set initiator-tcp-timeout

set initiator-gateway

To set the initiator gateway, use the set initiator-gateway command.

set initiator-gateway value

Syntax Description

value

IP address.

Command Default

None

Command Modes

iSCSI boot (chassis/adapter/host-eth-if/iscsi-boot)

Command History

Release	Modification
1.5(1)	The command was introduced.

Usage Guidelines

To set the initiator gateway, an iSCSI boot target for a vNIC must be created.

Examples

This example shows how to set the initiator gateway:

server # scope chassis
server /chassis # scope adapter 1
server /chassis/adapter # scope host-eth-if eth0
server /chassis/adapter/host-eth-if # create iscsi-boot 0
server /chassis/adapter/host-eth-if/iscsi-boot*# set initiator-gateway 1.2.3.4
server /chassis/adapter/host-eth-if/iscsi-boot*# commit
server /chassis/adapter/host-eth-if/iscsi-boot #

Related Commands

Command	Description
set initiator-chap-name
set initiator-chap-secret
set initiator-ipaddr
set initiator-name
set initiator-primary-dns
set initiator-secondary-dns
set initiator-subnet-mask
set initiator-tcp-timeout

set initiator-ipaddr

To set the IP address of the iSCSI initiator, use the set initiator-ipaddr command.

set initiator-ipaddr value

Syntax Description

value

The IP address of the iSCSI initiator.

Command Default

None

Command Modes

iSCSI boot (chassis/adapter/host-eth-if/iscsi-boot)

Command History

Release	Modification
1.5(1)	The command was introduced.

Usage Guidelines

To set the IP address of the iSCSI initiator, an iSCSI boot target for a vNIC must be created.

Examples

This example shows how to set IP address of the iSCSI initiator:

server# scope chassis
server /chassis # scope adapter 1
server /chassis/adapter # scope host-eth-if eth0
server /chassis/adapter/host-eth-if # create iscsi-boot 0
server /chassis/adapter/host-eth-if/iscsi-boot*# set initiator-ipaddr 1.2.3.4
server /chassis/adapter/host-eth-if/iscsi-boot*# commit
server /chassis/adapter/host-eth-if/iscsi-boot #

Related Commands

Command	Description
set initiator-chap-name
set initiator-chap-secret
set initiator-gateway
set initiator-name
set initiator-primary-dns
set initiator-secondary-dns
set initiator-subnet-mask
set initiator-tcp-timeout

set initiator-name

To set the name of the iSCSI initiator, use the set initiator-name command.

set initaitor-name string

Syntax Description

string

The name of the iSCSI initiator. Enter any alphanumeric string. The name can include a maximum of 223 characters.

Command Default

None

Command Modes

iSCSI boot (chassis/adapter/host-eth-if/iscsi-boot)

Command History

Release	Modification
1.5(1)	The command was introduced.

Usage Guidelines

To set the name of the iSCSI initiator, an iSCSI boot target for a vNIC must be created.

Examples

This example shows how to set the name of iSCSI initiator:

server# scope chassis
server /chassis # scope adapter 1
server /chassis/adapter # scope host-eth-if eth0
server /chassis/adapter/host-eth-if # create iscsi-boot 0
server /chassis/adapter/host-eth-if/iscsi-boot*# set initiator-name test 
server /chassis/adapter/host-eth-if/iscsi-boot*# commit
server /chassis/adapter/host-eth-if/iscsi-boot #

Related Commands

Command	Description
set initiator-chap-name
set initiator-chap-secret
set initiator-gateway
set initiator-ipaddr
set initiator-primary-dns
set initiator-secondary-dns
set initiator-subnet-mask
set initiator-tcp-timeout

set initiator-primary-dns

To set the primary DNS server address, use the set initiator-primary-dns command.

set initiator-primary-dns value

Syntax Description

value

The primary DNS server address.

Command Default

None

Command Modes

iSCSI boot (chassis/adapter/host-eth-if/iscsi-boot)

Command History

Release	Modification
1.5(1)	The command was introduced.

Usage Guidelines

To set the primary DNS server address, an iSCSI boot target for a vNIC must be created.

Examples

This example shows how to set the primary DNS server address:

server# scope chassis
server /chassis # scope adapter 1
server /chassis/adapter # scope host-eth-if eth0
server /chassis/adapter/host-eth-if # create iscsi-boot 0
server /chassis/adapter/host-eth-if/iscsi-boot*# set initiator-primary-dns 1.2.3.4 
server /chassis/adapter/host-eth-if/iscsi-boot*# commit
server /chassis/adapter/host-eth-if/iscsi-boot *#

Related Commands

Command	Description
set initiator-chap-name
set initiator-chap-secret
set initiator-gateway
set initiator--ipaddr
set initiator-name
set initiator-secondary-dns
set initiator-subnet-mask
set initiator-tcp-timeout

set initiator-secondary-dns

To set the secondary DNS server address, use the set initiator-secondary-dns command.

set initiator-secondary-dns value

Syntax Description

value

The secondary DNS server address.

Command Default

None

Command Modes

iSCSI boot (chassis/adapter/host-eth-if/iscsi-boot)

Command History

Release	Modification
1.5(1)	The command was introduced.

Usage Guidelines

To set the secondary DNS server address, an iSCSI boot target for a vNIC must be created.

Examples

This example shows how to set the secondary DNS server address:

server# scope chassis
server /chassis # scope adapter 1
server /chassis/adapter # scope host-eth-if eth0
server /chassis/adapter/host-eth-if # create iscsi-boot 0
server /chassis/adapter/host-eth-if/iscsi-boot*# set initiator-secondary-dns 1.2.3.4
server /chassis/adapter/host-eth-if/iscsi-boot*# commit
server /chassis/adapter/host-eth-if/iscsi-boot #

Related Commands

Command	Description
set initiator-chap-name
set initiator-chap-secret
set initiator-gateway
set initiator-ipddar
set initiator-name
set initiator-primary-dns
set initiator-subnet-mask
set initiator-tcp-timeout

set initiator-subnet-mask

To set the subnet mask for the initiator, use the set initiator-subnet-mask command.

set initiator-subnet-mask value

Syntax Description

value

The subnet mask for the iSCSI initiator.

Command Default

None

Command Modes

iSCSI boot (chassis/adapter/host-eth-if/iscsi-boot)

Command History

Release	Modification
1.5(1)	The command was introduced.

Usage Guidelines

To set the subnet mask for the iSCSI initiator, an iSCSI boot target for a vNIC must be created.

Examples

This example shows how to set subnet mask for the iSCSI initiator:

server# scope chassis
server /chassis # scope adapter 1
server /chassis/adapter # scope host-eth-if eth0
server /chassis/adapter/host-eth-if # create iscsi-boot 0
server /chassis/adapter/host-eth-if/iscsi-boot*# set initiator-subnet-mask 
server /chassis/adapter/host-eth-if/iscsi-boot*# commit 
server /chassis/adapter/host-eth-if/iscsi-boot #

Related Commands

Command	Description
set initiator-chap-name
set initiator-chap-secret
set initiator-gateway
set initiator-ipaddr
set initiator-name
set initiator-primary-dns
set initiator-secondary-dns
set initiator-tcp-timeout

set initiator-tcp-timeout

To set the number of seconds to wait before the initiator assumes that the TCP is unavailable, use the set initiator-tcp-timeout command.

set intiator-tcp-timeout value

Syntax Description

value

Time, in seconds. Enter an integer between 0 and 255.

Command Default

None

Command Modes

iSCSI boot (chassis/adapter/host-eth-if/iscsi-boot)

Command History

Release	Modification
1.5(1)	The command was introduced.

Usage Guidelines

To set the TCP timeout, an iSCSI boot target for a vNIC must be created.

Examples

This example shows how to set TCP timeout:

server# scope chassis
server /chassis # scope adapter 1
server /chassis/adapter # scope host-eth-if eth0
server /chassis/adapter/host-eth-if # create iscsi-boot 0
server /chassis/adapter/host-eth-if/iscsi-boot*# set initiator-tcp-timeout 60
server /chassis/adapter/host-eth-if/iscsi-boot*# commit
server /chassis/adapter/host-eth-if/iscsi-boot #

Related Commands

Command	Description
set initiator-chap-name
set initiator-chap-secret
set initiator-gateway
set initiator-ipaddr
set initiator-name
set initiator-primary-dns
set initiator-secondary-dns
set initiator-subnet-mask

set IntelHyperThread

To specify whether the processor uses Intel Hyper-Threading Technology, use the set IntelHyperThread command.

set IntelHyperThread { Disabled | Enabled }

Syntax Description

Disabled	The processor does not permit hyperthreading.
Enabled	The processor allows for the parallel execution of multiple threads.

Command Default

The processor allows for the parallel execution of multiple threads.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Intel Hyper-Threading Technology allows multithreaded software applications to execute threads in parallel within each processor.

Note

We recommend that you contact your operating system vendor to make sure the operating system supports this feature.

Examples

This example specifies that the processor does not permit hyperthreading and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set IntelHyperThread Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set IntelTurboBoostTech

To specify whether the processor uses Intel Turbo Boost Technology, use the set IntelTurboBoostTech command.

set IntelTurboBoostTech { Disabled | Enabled }

Syntax Description

Disabled	The processor does not automatically increase its frequency.
Enabled	The processor uses Intel Turbo Boost Technology if required.

Command Default

The processor uses Intel Turbo Boost Technology if required.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Intel Turbo Boost Technology allows the processor to automatically increase its frequency if it is running below power, temperature, or voltage specifications.

Note

The server ignores the setting for this command unless Power Management is set to Custom in the GUI, or the set CPUPowerManagement command is set to Custom in the CLI.

Examples

This example specifies that Intel Turbo Boost Technology is not used and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set IntelTurboBoostTech Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set CPUPowerManagement

set IntelVT

To specify whether the processor uses Intel Virtualization Technology, use the set IntelVT command.

set IntelVT { Disabled | Enabled }

Syntax Description

Disabled	The processor does not permit virtualization.
Enabled	The processor allows virtualization.

Command Default

The processor allows virtualization.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Use this command to specify whether the processor uses Intel Virtualization Technology (VT), which allows a platform to run multiple operating systems and applications in independent partitions.

Note

If you change this option, you must power cycle the server before the setting takes effect.

Examples

This example specifies that the processor does not permit virtualization and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set IntelVT Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set IntelVTD

To specify whether the processor uses Intel Virtualization Technology for Directed I/O (VT-d), use the set IntelVTD command.

set IntelVTD { Disabled | Enabled }

Syntax Description

Disabled	The processor does not use virtualization technology for directed I/O.
Enabled	The processor uses virtualization technology for directed I/O.

Command Default

The processor uses virtualization technology for directed I/O.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example specifies that the processor does not use virtualization technology for directed I/O and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set IntelVTD Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set interrupt-count

To specify the number of interrupt resources, use the set interrupt-count command.

set interrupt-count count

Syntax Description

count

The number of interrupt resources. The range is 1 to 514.

Command Default

The default is 8.

Command Modes

Interrupt (/chassis/adapter/host-eth-if/interrupt)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the interrupt count:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # scope interrupt
Server /chassis/adapter/host-eth-if/interrupt # set interrupt-count 10 
Server /chassis/adapter/host-eth-if/interrupt *# commit
Committed host-eth-if eth0 settings will take effect upon the next server reset
Server /chassis/adapter/host-eth-if/interrupt #

Related Commands

Command	Description
set coalescing-time
set coalescing-type

set interrupt-mode

To set the Ethernet interrupt mode, use the set interrupt-mode command.

set interrupt-mode { intx | msi | msix }

Syntax Description

intx	Line-based interrupt (PCI INTx).
msi	Message-Signaled Interrupt (MSI).
msix	Message Signaled Interrupts with the optional extension (MSI-X). This is the recommended and default option.

Command Default

The default option is msix.

Command Modes

Interrupt (/chassis/adapter/host-eth-if/interrupt)

Interrupt (/chassis/adapter/host-fc-if/interrupt)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the interrupt mode:

Server# scope chassis
Server /chassis/ # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if/ # scope interrupt
Server /chassis/adapter/host-eth-if/interrupt # set interrupt-mode msix 
Server /chassis/adapter/host-eth-if/interrupt *# commit
Committed host-eth-if eth0 settings will take effect upon the next server reset
Server /chassis/adapter/host-eth-if/interrupt #

Related Commands

Command	Description
set interrupt-count

set InterruptRemap

To specify whether the processor supports Intel VT-d Interrupt Remapping, use the set InterruptRemap command.

set InterruptRemap { Disabled | Enabled }

Syntax Description

Disabled	The processor does not support remapping.
Enabled	The processor uses VT-d Interrupt Remapping as required.

Command Default

The processor uses VT-d Interrupt Remapping as required.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example specifies that the processor does not use remapping and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set InterruptRemap Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set ip-ver

To set the IP version to use during iSCSI boot, use the set ip-ver command.

set ip-ver IPv4 IPv6

Syntax Description

IPv4	The IPv4 version to use during iSCSI boot.
IPv6	The IPv6 version to use during iSCSI boot.

Command Default

None

Command Modes

iSCSI boot (chassis/adapter/host-eth-if/iscsi-boot)

Command History

Release	Modification
1.5(1)	The command was introduced.

Usage Guidelines

To set the IP version, an iSCSI boot target for a vNIC must be created.

Examples

This example shows how to set the IP version to use during iSCSI boot:

server# scope chassis
server /chassis # scope adapter 1
server /chassis/adapter # scope host-eth-if eth0
server /chassis/adapter/host-eth-if # create iscsi-boot 0
server /chassis/adapter/host-eth-if/iscsi-boot*# set ip-ver ipv4
server /chassis/adapter/host-eth-if/iscsi-boot*# commit
server /chassis/adapter/host-eth-if/iscsi-boot #

set iqn

To specify a name of the iSCSI initiator for the target, use the set iqn command.

set iqn name

Syntax Description

name	Name of the iSCSI initiator in the IQN format. You can specify up to 223 alphanumeric characters.

Command Default

None

Command Modes

iSCSI target (/chassis/adapter/host-eth-if/iscsi-boot/iscsi-target)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

None

Examples

This example shows how to set the IQN for the iSCSI target:

Server # scope chassis
Server /chassis # scope adapter 3
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # scope iscsi-boot 0
Server /chassis/adapter/host-eth-if/iscsi-boot # create iscsi-target 1
Server /chassis/adapter/host-eth-if/iscsi-boot/iscsi-target* # set iqn sample_name1
Server /chassis/adapter/host-eth-if/iscsi-boot/iscsi-target* # commit
Server /chassis/adapter/host-eth-if/iscsi-boot/iscsi-target #

Related Commands

Command	Description
set boot-lun
set chap-name
set chap-secret
set ipaddr

set kvm-port

To specify the port used for KVM communication, use the set kvm-port command.

set kvm-port port-number

Syntax Description

port-number

The port used for KVM communication.

Command Default

Port number 2068 is used for KVM communication.

Command Modes

KVM (/kvm)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example specifies that port number 2068 is used for KVM communication:

server# scope kvm
server /kvm # set enabled yes
server /kvm* # set kvm-port 2068
server /kvm* # commit
server /kvm #

Related Commands

Command	Description
show kvm

set LaunchPXEOptionROM

To specify whether the server can perform a PXE boot, use the set LaunchPXEOptionROM command.

set LaunchPXEOptionROM { Disabled | Enabled }

Syntax Description

Disabled	The server cannot perform a PXE boot.
Enabled	The server can perform a PXE boot.

Command Default

The server can perform a PXE boot.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(4)	This command was introduced.

Examples

This example specifies that the server can perform a PXE boot and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set LaunchPXEOptionROM Enabled
Server /bios/advanced *# commit
Server /bios/advanced #

set LegacyOSRedir

To specify whether redirection from a legacy operating system, such as DOS, is enabled on the serial port, use the set LegacyOSRedir command.

set LegacyOSRedir { Disabled | Enabled }

Syntax Description

Disabled	The serial port enabled for console redirection is hidden from the legacy operating system.
Enabled	The serial port enabled for console redirection is visible to the legacy operating system.

Command Default

Disabled

Command Modes

Server Management BIOS (/bios/server-management)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example makes the serial port enabled for console redirection visible to the legacy operating system and commits the transaction:

Server# scope bios
Server /bios # scope server-management
Server /bios/server-management # set LegacyOSRedir Enabled
Server /bios/server-management *# commit
Server /bios/server-management #

Related Commands

Command	Description
show server-management

set LegacyUSBSupport

To specify whether the system supports legacy USB devices, use the set LegacyUSBSupport command.

set LegacyUSBSupport { Auto | Disabled | Enabled }

Syntax Description

Auto	Disables legacy USB support if no USB devices are connected.
Disabled	USB devices are available only to EFI applications.
Enabled	Legacy USB support is always available.

Command Default

Legacy USB support is always available.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(4)	This command was introduced.

Examples

This example specifies that legacy USB support is always available and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set LegacyUSBSupport Enabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set UsbEmul6064

set link-busy-retry-count

To set the number of times to retry the connection in case of a failure during iSCSI LUN discovery, use the set link-busy-retry-count command.

set link-busy-retry-count value

Syntax Description

value

Enter an integer between 0 and 255.

Command Default

None

Command Modes

iSCSI boot (chassis/adapter/host-eth-if/iscsi-boot)

Command History

Release	Modification
1.5(1)	The command was introduced.

Usage Guidelines

To set LUN busy retry count, an iSCSI boot target for a vNIC must be created.

Examples

This example shows how to set LUN busy retry count:

server# scope chassis
server /chassis # scope adapter 1
server /chassis/adapter # scope host-eth-if eth0
server /chassis/adapter/host-eth-if # create iscsi-boot 0
server /chassis/adapter/host-eth-if/iscsi-boot*# set link-busy-retry-count 60
server /chassis/adapter/host-eth-if/iscsi-boot*# commit
server /chassis/adapter/host-eth-if/iscsi-boot #

set link-down-timeout

To set the link down timeout of the host Fibre Channel Interface, use the set link-down-timeout command.

set link-down-timeout msec

Syntax Description

msec	Specifies the link down timeout value, the number of milliseconds the uplink port should be offline before it informs the system that the uplink port is down and fabric connectivity has been lost. The range is 0 to 240000.

Command Default

The default is 30000 milliseconds.

Command Modes

Error-recovery (/chassis/adapter/host-fc-if/error-recovery)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the link down timeout:

Server# scope chassis
Server /chassis/ # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0 
Server /chassis/adapter/host-fc-if # scope error-recovery
Server /chassis/adapter/host-fc-if/error-recovery # set link-down-timeout 2000
Server /chassis/adapter/host-fc-if/error-recovery *# commit
Committed host-fc-if fc0 settings will take effect upon the next server reset

set linkup-timeout

To set the number of seconds to wait before the initiator assumes that the link is unavailable, use the set linkup-timeout command.

set linkup-timeout value

Syntax Description

value

Number of seconds. Enter an integer between 0 and 255.

Command Default

None

Command Modes

iSCSI boot (chassis/adapter/host-eth-if/iscsi-boot)

Command History

Release	Modification
1.5(1)	The command was introduced.

Usage Guidelines

To set the linkup timeout, iSCSI boot must be created.

Examples

This example shows how to set linkup timeout value:

server# scope chassis
server /chassis # scope adapter 1
server /chassis/adapter # scope host-eth-if eth0
server /chassis/adapter/host-eth-if # create iscsi-boot 0
server /chassis/adapter/host-eth-if/iscsi-boot*# set linkup-timeout 60
server /chassis/adapter/host-eth-if/iscsi-boot*# commit
server /chassis/adapter/host-eth-if/iscsi-boot #

set local-syslog-severity

To specify the lowest level of messages that will be included in the CIMC log, use the set local-syslog-severity command.

set local-syslog-severity level

Syntax Description

level

The lowest level of messages that will be included in the CIMC log. See the Usage Guidelines for valid values.

Command Default

Messages of level Debug and higher are logged.

Command Modes

CIMC log (/cimc/log)

Command History

Release	Modification
1.4(3)	This command was introduced.

Usage Guidelines

The severity level can be one of the following, in decreasing order of severity:

emergency
alert
critical
error
warning
notice
informational
debug

CIMC does not log any messages with a severity below the selected severity. For example, if you select error, the CIMC log will contain all messages with the severity Emergency, Alert, Critical, or Error. It will not show Warning, Notice, Informational, or Debug messages.

Examples

This example shows how to configure the logging of messages with a minimum severity of Warning:

Server# scope cimc
Server /cimc # scope log
Server /cimc/log # set local-syslog-severity warning
Server /cimc/log *# commit
Server /cimc/log #

Related Commands

Command	Description
show local-syslog-severity

set local-video

To enable or disable the display of the KVM session on any monitor attached to the server, use the set local-video command.

set local-video { no | | yes }

Syntax Description

no	The KVM session is not displayed on any monitor attached to the server.
yes	The KVM session is displayed on any monitor attached to the server.

Command Default

The KVM session is displayed on any monitor attached to the server.

Command Modes

KVM (/kvm)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example enables the display of the KVM session on any monitor attached to the server:

server# scope kvm
server /kvm # set enabled yes
server /kvm* # set local-video yes
server /kvm* # commit
server /kvm #

Related Commands

Command	Description
show kvm

set locator-led

To turn the server locator LED on or off, use the set locator-led command.

set locator-led { off | on }

Syntax Description

off	Turns the locator LED off.
on	Turns the locator LED on.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to turn on or off the locator LED for the chassis.

Examples

This example shows how to turn on the locator LED for the chassis:

server# scope chassis
server /chassis # set locator-led on
server /chassis* # commit
server /chassis #

Related Commands

Command	Description
show chassis
show led

set LomOpromControlPortn

To specify whether Option ROM is available on a legacy LOM port, use the set LomOpromControlPortn command.

set LomOpromControlPortn { Disabled | Enabled }

Syntax Description

n	Specifies a legacy LOM port number.
Disabled	Option ROM is not available on the specified LOM port.
Enabled	Option ROM is available on the specified LOM port.

Command Default

Option ROM is available on legacy LOM ports.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(5)	This command was introduced.

Usage Guidelines

Use this command to specify whether Option ROM is available on the legacy LOM port designated by n in the command name set LomOpromControlPortn.

Examples

This example specifies that Option ROM is not available on the legacy LOM port 2 and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set LomOpromControlPort2 Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set low-power-usb-enabled

To enable the low power USB for the virtual media, use the set low-power-usb-enabled command.

set low-power-usb-enabled { yes | no }

Syntax Description

yes	Enables the low power USB. When enabled, after mapping the ISO, and rebooting the host the card resets and ISO mapping is lost. The virtual drives are not visible on the boot selection menu.
no	Disables the low power USB. When disabled, after mapping the ISO, and rebooting the host and the CIMC, the virtual drivers appear on the boot selection menu as expected.

Command Default

The default state of low power USB is enabled.

Command Modes

Low power USB (/Server/vmedia)

Command History

Release	Modification
1.5(2)	This command was introduced.

Usage Guidelines

Disable while mapping the ISO, this will ensure that the mapping is successful and the virtual drives appear on the boot selection menu.

Examples

This example shows how to disable the low power USB:

Server# scope vmedia
Server /vmedia # set enabled yes
Server /vmedia *# set encryption yes
Server /vmedia *# set low-power-use-enabled no
Server /vmedia *# commit
Server /vmedia # show detail
vMedia Settings:
    Encryption Enabled: yes
    Enabled: yes
    Max Sessions: 1
    Active Sessions: 0
				Low Power USB Enabled: no

Server /vmedia #

set LvDDRMode

To specify whether the system prioritizes low voltage or high frequency memory operations, use the set LvDDRMode command.

set LvDDRMode { Performance_Mode | Power_Saving_Mode }

Syntax Description

Performance_Mode	The system prioritizes high frequency operations over low voltage operations.
Power_Saving_Mode	The system prioritizes low voltage memory operations over high frequency memory operations. This mode may lower memory frequency in order to keep the voltage low.

Command Default

The system prioritizes low voltage memory operations over high frequency memory operations.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example specifies that high frequency memory operations are optimized and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set LvDDRMode Performance_Mode
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set mac-addr

To specify a MAC address for an interface, use the set mac-addr command.

set mac-addr mac-addr

Syntax Description

mac-addr

Specifies a MAC address in the form hh:hh:hh:hh:hh:hh or hhhh:hhhh:hhhh.

Command Default

None

Command Modes

Ethernet host interface (/chassis/adapter/host-eth-if)

Fibre Channel host interface (/chassis/adapter/host-fc-if)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to specify a MAC address for the Fibre Channel host interface fc0:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # set mac-addr 0123:4567:89ab
Server /chassis/adapter/host-fc-if *# commit
Server /chassis/adapter/host-fc-if #

Related Commands

Command	Description

set MakeUSBDeviceNonBootable

To specify whether the server can boot from a USB device, use the set MakeUSBDeviceNonBootable command.

set MakeUSBDeviceNonBootable { Disabled | Enabled }

Syntax Description

Disabled	The server can boot from a USB device.
Enabled	The server cannot boot from a USB device.

Command Default

The server can boot from a USB device.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example allows the server to boot from a USB device and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set MakeUSBDeviceNonBootable Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set USBController
show advanced

set ManagedBootRule

To specify how the server changes the boot order list defined through the CIMC GUI or CLI when there are no devices of a particular device type available or when the user defines a different boot order using the server's BIOS Setup Utility, use the set ManagedBootRule command.

set ManagedBootRule { Strict | Loose }

Syntax Description

Strict

When no devices of a particular type are available, the system creates a placeholder for that device type in the boot order list. When a device of that type becomes available, it is added to the boot order in the previously defined position.

If the user defines a boot order through the server's BIOS Setup Utility, that boot order is given priority over the boot order configured through the CIMC GUI or CLI. All device types defined through CIMC that are not present in the boot order defined through the BIOS Setup Utility are removed from the boot order list.

Loose

When no devices of a particular type are available, the system removes that device type from the boot order. When a device of that type becomes available, the system adds it to the end of the boot order list.

If the boot order is configured through the server's BIOS Setup Utility, that boot order is given priority over the boot order configured through the CIMC GUI or CLI. All device types defined through CIMC that are not present in the boot order defined through the BIOS Setup Utility are moved to the end of the boot order list.

Command Default

The Boot Order Rules option is loose.

Command Modes

Server Management BIOS (/bios/server-management)

Command History

Release	Modification
1.4(6)	This command was introduced.

Usage Guidelines

Use this command to specify how the server changes the boot order list defined through the CIMC GUI or CLI when there are no devices of a particular device type available or when the user defines a different boot order using the server's BIOS Setup Utility, use the set ManagedBootRule command.

The supported device types are:

HDD—Hard disk drive
FDD—Floppy disk drive
CDROM—Bootable CD-ROM or DVD
PXE—PXE boot
EFI—Extensible Firmware Interface

Examples

This example changes the Boot Order Rules option to strict and commits the transaction:

Server# scope bios
Server /bios # scope server-management
Server /bios/server-management # set ManagedBootRule Strict
Server /bios/server-management *# commit
Server /bios/server-management #

Related Commands

Command	Description
show actual-boot-order (bios)

set max-data-field-size

To specify the maximum data field size for the Fibre Channel interface, use the set max-data-field-size command.

set max-data-field-size size

Syntax Description

size	The maximum data field size. Specify a number between 256 and 2112.

Command Default

The maximum data field size is 2112.

Command Modes

Fibre Channel host interface (/chassis/adapter/host-fc-if)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example shows how to set the maximum data field size to 1024 on interface fc0 on adapter card 1:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # set max-data-field-size 1024
Server /chassis/adapter/host-fc-if *# commit
Server /chassis/adapter/host-fc-if #

Related Commands

Command	Description
show host-fc-if detail

set max-sessions

To specify the maximum number of concurrent KVM sessions allowed, use the set max-sessions command.

set max-sessions sessions

Syntax Description

sessions

The maximum number of concurrent KVM sessions allowed. This can be an integer between 1 and 4.

Command Default

A maximum of four concurrent KVM sessions is allowed.

Command Modes

KVM (/kvm)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example specifies that a maximum of two concurrent KVM sessions is allowed:

server# scope kvm
server /kvm # set enabled yes
server /kvm* # set max-sessions 2
server /kvm* # commit
server /kvm #

Related Commands

Command	Description
show kvm

set max-target-luns

To set the maximum logical unit numbers (LUNs) per target, use the set max-target-luns command.

set max-target-luns count

Syntax Description

count

The maximum logical unit numbers (LUNs) per target; the maximum number of LUNs that the driver will discover. The range is 1 to 1024.

Command Default

The default is 256 LUNs.

Command Modes

Port (/chassis/adapter/host-fc-if/port)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the max-target-luns:

Server# scope chassis
Server /chassis scope adapter 1
Server /chassis/adapter scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # scope port
Server /chassis/adapter/host-fc-if/port # set max-target-luns 334
Server /chassis/adapter/host-fc-if/port *# commit
Server /chassis/adapter/host-fc-if/port #

Related Commands

None

set MemoryMappedIOAbove4GB

To enable or disable memory mapped I/O of 64-bit PCI devices to 4GB or greater address space, use the set MemoryMappedIOAbove4GB command.

set MemoryMappedIOAbove4GB { Disabled | Enabled }

Syntax Description

Disabled	The server does not map I/O of 64-bit PCI devices to 4GB or greater address space.
Enabled	The server maps I/O of 64-bit PCI devices to 4GB or greater address space.

Command Default

The server does not map I/O of 64-bit PCI devices to 4GB or greater address space.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Use this command to enable or disable memory mapped I/O of 64-bit PCI devices to 4GB or greater address space. Legacy option ROMs are not able to access addresses above 4GB. PCI devices that are 64-bit compliant but use a legacy option ROM may not function correctly with this setting enabled.

Examples

This example allows the server to map I/O of 64-bit PCI devices to 4GB or greater address space and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set MemoryMappedIOAbove4GB Enabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set MirroringMode

To specify how memory is mirrored, use the set MirroringMode command.

set MirroringMode { Intersocket | Intrasocket }

Syntax Description

Intersocket	Each IMC is mirrored across two sockets.
Intrasocket	One IMC is mirrored with another IMC in the same socket.

Command Default

One IMC is mirrored with another IMC in the same socket.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to specify how memory is mirrored. Mirroring is supported across Integrated Memory Controllers (IMCs) where one memory riser is mirrored with another.

Note

This command is operative only if the set SelectMemoryRAS command is set to Mirroring.

Examples

This example configures memory mirroring across two sockets and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set SelectMemoryRAS Mirroring
Server /bios/advanced *# set MirroringMode Intersocket
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set SelectMemoryRAS
show advanced

set mode

To specify the server NIC mode, use the set mode command.

set mode { dedicated | shared_lom | shared_lom_10g | cisco_card | shipping }

Syntax Description

dedicated

The management Ethernet port is used to access the CIMC.

shared_lom

The LAN On Motherboard (LOM) Ethernet host ports are used to access the CIMC.

Note

If you select Shared LOM, make sure that all host ports belong to the same subnet.

shared_lom_10g

(If supported) The 10G LOM Ethernet host ports are used to access the CIMC.

cisco_card

The ports on the installed adapter card are used to access the CIMC.

shipping

(If supported) The management Ethernet port or ports provide a limited factory default configuration for initial connection. Select another mode for normal operation.

Command Default

None

Command Modes

Network (/cimc/network)

Command History

Release	Modification
1.0(1)	This command was introduced.
1.0(1x)	The shipping keyword was introduced.

Examples

This example sets the server NIC mode to dedicated:

server# scope cimc
server /cimc # scope network
server /cimc/network # set mode dedicated
server /cimc/network* # commit
server /cimc/network #

Related Commands

Command	Description
show network

set mtu

To specify an MTU for a vNIC, use the set mtu command.

set mtu mtu-value

Syntax Description

mtu-value

Specifies the maximum transmission unit (MTU) or packet size that the vNIC accepts. Valid MTU values are 1500 to 9000 bytes; the default is 1500.

Command Default

The MTU is 1500 bytes.

Command Modes

Ethernet host interface (/chassis/adapter/host-eth-if)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to specify an MTU of 9000 for the Ethernet host interface eth0:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # set mtu 9000
Server /chassis/adapter/host-eth-if *# commit
Server /chassis/adapter/host-eth-if #

Related Commands

Command	Description

set name

To specify a user name, use the set name command.

set name user-name

Syntax Description

user-name

The name of the user. The name can contain up to 70 characters.

Command Default

None

Command Modes

User (/user)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example configures a user name, password, and role:

server# scope user
server /user # set enabled yes
server /user* # set name user15
server /user* # set password cisco123
server /user* # set role read-only
server /user* # commit
server /user #

Related Commands

Command	Description
show user

set NIC-ROM

To enable or disable an onboard NIC ROM, use the set NIC-ROM command.

set NIC-n-ROM { Disabled | Enabled }

Syntax Description

n	The number of the onboard NIC ROM.
Disabled	The onboard NIC ROM is disabled.
Enabled	The onboard NIC ROM is enabled.

Command Default

The onboard NIC ROM is enabled.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to enable or disable an onboard network interface card (NIC) ROM.

Examples

This example disables the onboard NIC 2 ROM and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set NIC-2-ROM Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set niv-mode

To enable or disable Network Interface Virtualization (NIV) on the adapter card, use the set niv-mode command.

set niv-mode { disabled | enabled }

Syntax Description

disabled	Disables NIV mode on the card.
enabled	Enables NIV mode on the card.

Command Default

NIV mode is disabled.

Command Modes

Adapter (/chassis/adapter)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Use this command to enable or disable NIV mode on the adapter card. When NIV mode is enabled, vNICs have the following features:

Can be assigned to a specific channel
Can be associated with a port profile
Can fail over to another vNIC if there are communication problems

Examples

This example shows how to enable NIV mode on adapter card 1:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # set niv-mode enabled
Server /chassis/adapter *# commit
Server /chassis/adapter #

Related Commands

Command	Description
show adapter

set non-compliance-action

To specify the action the system should take if power capping is enabled and the server requests more than its peak power allotment, use the set non-compliance-action command.

set non-compliance-action { force-power-reduction | none | power-off-host | throttle }

Syntax Description

force-power-reduction	The server is forced to reduce its power consumption by any means necessary. This option is not available on some server models.
none	No action is taken and the server is allowed to use more power than specified in the peak power setting.
power-off-host	The server is shut down.
throttle	Processes running on the server are throttled to bring the total power consumption down.

Command Default

None

Command Modes

Power cap (/power-cap)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Use this command to specify the action the system should take if power capping is enabled and the server requests more than its peak power allotment.

Examples

This example sets the non-compliance action to throttle processes on the server and commits the transaction:

Server# scope power-cap
Server /power-cap # set enabled yes
Server /power-cap *# set peak-power 1000
Server /power-cap *# set non-compliance-action throttle
Server /power-cap *# commit
Server /power-cap #  show detail
    Cur Consumption (W): 688
    Max Consumption (W): 1620
    Min Consumption (W): 48
    Minimum Configurable Limit (W): 500
    Maximum Configurable Limit (W): 2000
    Power Cap Enabled: yes
    Peak Power: 1000
    Non Compliance Action: throttle

Server /power-cap #

Related Commands

Command	Description
set peak-power
show power-cap

set NUMAOptimize

To specify whether the BIOS supports Non-Uniform Memory Access (NUMA), use the set NUMAOptimize command.

set NUMAOptimize { Disabled | Enabled }

Syntax Description

Disabled	The BIOS does not support NUMA.
Enabled	The BIOS includes the ACPI tables that are required for NUMA-aware operating systems.

Command Default

NUMA support is enabled.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Use this command to specify whether the BIOS supports NUMA. When NUMA support is enabled, the BIOS includes the ACPI tables that are required for NUMA-aware operating systems.

Note

If you enable this option, the system must disable Inter-Socket Memory interleaving on some platforms.

Examples

This example disables NUMA support in the BIOS and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set NUMAOptimize Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set OEMAESNIControl

To specify whether the server uses the AES-NI encryption instruction set, use the set OEMAESNIControl command.

set OEMAESNIControl { Disabled | Enabled }

Syntax Description

Disabled	The server does not use the AES-NI instruction set.
Enabled	The server uses the AES-NI instruction set when possible.

Command Default

The server does not use the AES-NI instruction set.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(3)	This command was introduced.

Usage Guidelines

Use this command to specify whether the server uses the processor's AES-NI (New Instructions) encryption instruction set that improves on the Advanced Encryption Standard (AES) algorithm.

Examples

This example specifies that the server uses the processor's AES-NI instruction set and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set OEMAESNIControl Enabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description

set OnboardNic1

To enable or disable the first onboard Network Interface Card (NIC) on the server, use the set OnboardNic1 command.

set OnboardNic1 { Disabled | Enabled }

Syntax Description

Disabled	NIC 1 is not available.
Enabled	NIC 1 is available.

Command Default

NIC 1 is available.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

By replacing the numeral 1 in the command with the numeral 2, you can modify this command to specify whether the onboard NIC2 is available. For example, to enable or disable NIC 2, use the set OnboardNic2 command.

Examples

This example disables NIC 1 and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set OnboardNic1 Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set OnboardNic1ROM
show advanced

set OnboardNic1ROM

To specify whether the system loads the embedded PXE option ROM for the first onboard NIC on the server, use the set OnboardNic1ROM command.

set OnboardNic1ROM { Disabled | Enabled }

Syntax Description

Disabled	The PXE option ROM is not available for NIC 1.
Enabled	The PXE option ROM is available for NIC 1.

Command Default

The PXE option ROM is available for NIC 1.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

By replacing the numeral 1 in the command with the numeral 2, you can modify this command to specify whether the PXE option ROM for onboard NIC2 is available. For example, to specify the option ROM for NIC 2, use the set OnboardNic2ROM command.

Examples

This example specifies that the PXE option ROM is available for NIC 1 and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set OnboardNic1ROM Enabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set OnboardNic1
show advanced

set OnboardSATA

To specify whether the server uses its onboard built-in SATA controller, use the set OnboardSATA command.

set OnboardSATA { Disabled | Enabled }

Syntax Description

Disabled	The server does not use its onboard built-in SATA controller.
Enabled	The server uses its onboard built-in SATA controller.

Command Default

The server uses its onboard built-in SATA controller.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Note

This command is not available on all models and configurations.

Examples

This example specifies that the server does not use its onboard built-in SATA controller and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set OnboardSATA Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set OptionROMPriority

To specify which Option ROM the server should launch, use the set OptionROMPriority command.

set OptionROMPriority { EFI_Compatible_ROM | Legacy_ROM | Enabled }

Syntax Description

EFI_Compatible_ROM	The server launches the EFI compatible PCI Option ROM.
Legacy_ROM	The server launches the legacy PCI Option ROM.

Command Default

The server launches the EFI compatible PCI Option ROM.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(4)	This command was introduced.

Usage Guidelines

If the server has both legacy and EFI compatible PCI Option ROMs, this command specifies which Option ROM the server should launch.

Examples

This example specifies that the server launches the EFI compatible PCI Option ROM and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set OptionROMPriority EFI_Compatible_ROM
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set MemoryMappedIOAbove4GB

set order

To specify the relative order of this device for PCI bus device number assignment, use the set order command.

set order { any | order }

Syntax Description

any	No relative order is specified.
order	Specifies a relative order. The range is 0 to 99.

Command Default

No relative order is specified.

Command Modes

Ethernet host interface (/chassis/adapter/host-eth-if)

Fibre Channel host interface (/chassis/adapter/host-fc-if)

Command History

Release	Modification
1.2(1)	This command was introduced.

Usage Guidelines

Use this command to specify the order of PCI bus number assignment of this device relative to other PCI bus devices. PCI bus numbers are assigned to devices by increasing relative order followed by devices for which no order is specified.

Examples

This example shows how to specify a relative PC bus number assignment order of 30 for the Fibre Channel host interface fc0:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # set order 30
Server /chassis/adapter/host-fc-if *# commit
Server /chassis/adapter/host-fc-if #

Related Commands

Command	Description

set OSBootWatchdogTimer

To specify whether the BIOS programs the operating system boot watchdog timer with a timeout value, use the set OSBootWatchdogTimer command.

set OSBootWatchdogTimer { Disabled | Enabled }

Syntax Description

Disabled	The OS boot watchdog timer is disabled.
Enabled	The OS boot watchdog timer is enabled.

Command Default

The OS boot watchdog timer is disabled.

Command Modes

Server Management BIOS (/bios/server-management)

Command History

Release	Modification
1.4(4)	This command was introduced.

Usage Guidelines

Use this command to specify whether the BIOS programs the operating system (OS) boot watchdog timer with a timeout value. This can be one of the following:

Disabled—The watchdog timer is not used to track how long the server takes to boot.
Enabled—The watchdog timer tracks how long the server takes to boot. If the server does not boot within the length of time specified by the set OSBootWatchdogTimerTimeout command, the CIMC logs an error and takes the action specified by the set OSBootWatchdogTimerPolicy command.

Examples

This example enables the OS boot watchdog timer with a duration of 10 minutes and an action of reset and commits the transaction:

Server# scope bios
Server /bios # scope server-management
Server /bios/server-management # set OSBootWatchdogTimer Enabled
Server /bios/server-management *# set OSBootWatchdogTimerTimeout 10_mins
Server /bios/server-management *# set OSBootWatchdogTimerPolicy Reset
Server /bios/server-management *# commit
Server /bios/server-management #

Related Commands

Command	Description
set OSBootWatchdogTimerPolicy
set OSBootWatchdogTimerTimeout

set OSBootWatchdogTimerPolicy

To specify what action the system takes if the operating system boot watchdog timer expires, use the set OSBootWatchdogTimerPolicy command.

set OSBootWatchdogTimerPolicy { Do_Nothing | Power_Down | Reset }

Syntax Description

Do_Nothing	No action is taken if the timer expires.
Power_Down	The server is powered off if the timer expires.
Reset	The server is reset if the timer expires.

Command Default

The server is reset if the timer expires.

Command Modes

Server Management BIOS (/bios/server-management)

Command History

Release	Modification
1.4(4)	This command was introduced.

Usage Guidelines

Use this command to specify what action the system takes if the operating system (OS) boot watchdog timer expires. This can be one of the following:

Do_Nothing—No action is taken if the OS boot watchdog timer expires.
Power_Down—The server is powered off if the server does not boot before the OS boot watchdog timer expires.
Reset—The server is reset if the server does not boot before the OS boot watchdog timer expires.

The duration of the OS boot watchdog timer is specified by the set OSBootWatchdogTimerTimeout command.

Note

This command is operative only if the OS boot watchdog timer is enabled by the set OSBootWatchdogTimer command.

Examples

This example enables the OS boot watchdog timer with a duration of 10 minutes and an action of reset and commits the transaction:

Server# scope bios
Server /bios # scope server-management
Server /bios/server-management # set OSBootWatchdogTimer Enabled
Server /bios/server-management *# set OSBootWatchdogTimerTimeout 10_mins
Server /bios/server-management *# set OSBootWatchdogTimerPolicy Reset
Server /bios/server-management *# commit
Server /bios/server-management #

Related Commands

Command	Description
set OSBootWatchdogTimer
set OSBootWatchdogTimerTimeout

set OSBootWatchdogTimerTimeout

To specify the duration of the operating system boot watchdog timer, use the set OSBootWatchdogTimerTimeout command.

set OSBootWatchdogTimerTimeout { 5_mins | 10_mins | 15_mins | 20_mins }

Syntax Description

5_mins	The timer duration is 5 minutes.
10_mins	The timer duration is 10 minutes.
15_mins	The timer duration is 15 minutes.
20_mins	The timer duration is 20 minutes.

Command Default

The timer duration is 10 minutes.

Command Modes

Server Management BIOS (/bios/server-management)

Command History

Release	Modification
1.4(4)	This command was introduced.

Usage Guidelines

Use this command to specify the duration of the operating system (OS) boot watchdog timer. If the server does not boot within the length of time specified by this command, the CIMC logs an error and takes the action specified by the set OSBootWatchdogTimerPolicy command.

Note

This command is operative only if the OS boot watchdog timer is enabled by the set OSBootWatchdogTimer command.

Examples

This example enables the OS boot watchdog timer with a duration of 10 minutes and an action of reset and commits the transaction:

Server# scope bios
Server /bios # scope server-management
Server /bios/server-management # set OSBootWatchdogTimer Enabled
Server /bios/server-management *# set OSBootWatchdogTimerTimeout 10_mins
Server /bios/server-management *# set OSBootWatchdogTimerPolicy Reset
Server /bios/server-management *# commit
Server /bios/server-management #

Related Commands

Command	Description
set OSBootWatchdogTimer
set OSBootWatchdogTimerPolicy

set outstanding-io-count

To set the outstanding IO count of the host Fibre Channel interface, use the set outstanding-io-count command.

set outstanding-io-count count

Syntax Description

count

Specifies the number of I/O operations that can be pending in the vHBA at one time. The range is 1 to 1024.

Command Default

The default is 512 operations.

Command Modes

Port (/chassis/adapter/host-fc-if/port)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the outstanding-io-count:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # scope port
Server /chassis/adapter/host-fc-if/port # set outstanding-io-count 343
Server /chassis/adapter/host-fc-if/port *# commit
Server /chassis/adapter/host-fc-if/port #

Related Commands

None

set PackageCStateLimit

To specify the amount of power available to the server components when they are idle, use the set PackageCStateLimit command.

set PackageCStateLimit { C0_state | C1_state | C3_state | C6_state | C7_state | No_Limit }

Syntax Description

Cn_state	Depending on n, the server provides full power to minimal power to the components. See the Usage Guidelines.
No_Limit	The server may enter any available C state.

Command Default

The default limit is C3_state.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to specify the amount of power available to the server components when they are idle. This can be one of the following:

C0_state—The server provides all server components with full power at all times. This option maintains the highest level of performance and requires the greatest amount of power.
C1_state—When the CPU is idle, the system slightly reduces the power consumption. This option requires less power than C0 and allows the server to return quickly to high performance mode.
C3_state—When the CPU is idle, the system reduces the power consumption further than with the C1 option. This requires less power than C1 or C0, but it takes the server slightly longer to return to high performance mode.
C6_state—When the CPU is idle, the system reduces the power consumption further than with the C3 option. This option saves more power than C0, C1, or C3, but there may be performance issues until the server returns to full power.
C7_state—When the CPU is idle, the server makes a minimal amount of power available to the components. This option saves the maximum amount of power but it also requires the longest time for the server to return to high performance mode.
No_Limit—The server may enter any available C state.

Note

This command is operative only if the set ProcessorCcxEnable command is set to Enabled.

Examples

This example specifies that a minimal amount of power is made available to the components when the CPU is idle and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set ProcessorCcxEnable Enabled
Server /bios/advanced # set PackageCStateLimit C7_state
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set ProcessorCcxEnable
show advanced

set PassThroughDMA

To specify whether the processor supports Intel VT-d Pass-through DMA, use the set PassThroughDMA command.

set PassThroughDMA { Disabled | Enabled }

Syntax Description

Disabled	The processor does not support pass-through DMA.
Enabled	The processor uses VT-d Pass-through DMA as required.

Command Default

The processor uses VT-d Pass-through DMA as required.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example specifies that the processor does not support VT-d Pass-through DMA and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set PassThroughDMA Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set password

To specify a user password, use the set password command.

set password user-password

Syntax Description

user-password

The password of the user. The password can contain up to 80 characters.

Command Default

None

Command Modes

User (/user)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example configures a user name, password, and role:

server# scope user
server /user # set enabled yes
server /user* # set name user15
server /user* # set password cisco123
server /user* # set role read-only
server /user* # commit
server /user #

Related Commands

Command	Description
show user

set path (tech-support)

To set the TFTP path, use the set path command in tech-support mode.

set path tftp-path

Syntax Description

tftp-path

The TFTP path.

Command Default

None

Command Modes

Technical support (/cimc/tech-support)

Command History

Release	Modification
1.0(1)	This command was introduced.
1.5(1)	This command has been replaced with the set remote-path command.

Usage Guidelines

Specifies the path to the support data file should be stored.

Perform this task along with set tftp-ip when requested by the Cisco Technical Assistance Center (TAC). This utility creates a summary report containing configuration information, logs and diagnostic data that will help TAC in troubleshooting and resolving technical issues.

Examples

This example shows how to set the TFTP path:

server# scope cimc
server /cimc # scope tech-support
server /cimc/tech-support # set path /test/test.bin
server /cimc/tech-support* # commit
server /cimc/tech-support #

Related Commands

Command	Description
set tftp-ip
show tech-support

set PatrolScrub

To specify whether the system actively searches for, and corrects, single bit memory errors, use the set PatrolScrub command.

set PatrolScrub { Disabled | Enabled }

Syntax Description

Disabled	The system checks for memory ECC errors only when the CPU reads or writes a memory address.
Enabled	The system periodically reads and writes memory searching for ECC errors.

Command Default

The system periodically reads and writes memory searching for ECC errors.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to specify whether the system actively searches for, and corrects, single bit memory errors even in unused portions of the memory on the server. If enabled and any errors are found, the system attempts to fix them. This option may correct single bit errors before they become multi-bit errors, but it may adversely affect performance when the patrol scrub is running.

When this function is disabled, the system checks for memory ECC errors only when the CPU reads or writes a memory address.

Examples

This example specifies that the system actively searches for and corrects single bit memory errors and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set PatrolScrub Enabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set PatrolScrubDuration
show advanced

set PatrolScrubDuration

To specify the interval between each patrol scrub memory access, use the set PatrolScrubDuration command.

set PatrolScrubDuration interval

Syntax Description

interval

A value between 5 and 23.

Command Default

The interval is 8.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to specify the interval between each patrol scrub memory access. A lower interval scrubs the memory more often but requires more memory bandwidth.

Note

This command is operative only if the set PatrolScrub command is set to Enabled.

Examples

This example specifies an interval of 20 between each patrol scrub memory access and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set PatrolScrub Enabled
Server /bios/advanced # set PatrolScrubDuration 20
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set PatrolScrub
show advanced

set Pci-Opt-Roms

To specify whether the server can use the PCIe Option ROM expansion slots, use the set Pci-Opt-Roms command.

set Pci-Opt-Roms { Disabled | Enabled }

Syntax Description

Disabled	The PCIe Option ROMs are not available.
Enabled	The PCIe Option ROMs are available.

Command Default

The PCIe Option ROMs are available.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example specifies that the PCIe Option ROMs are not available and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set Pci-Opt-Roms Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set PciMezzOptionROM

To specify whether the PCIe mezzanine slot expansion ROM is available to the server, use the set PciMezzOptionROM command.

set PciMezzOptionROM { Disabled | Enabled }

Syntax Description

Disabled	The PCIe mezzanine slot expansion ROM is not available to the server.
Enabled	The PCIe mezzanine slot expansion ROM is available to the server.

Command Default

The PCIe mezzanine slot expansion ROM is available to the server.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(5)	This command was introduced.

Examples

This example specifies that the PCIe mezzanine slot expansion ROM is available to the server and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set PciMezzOptionROM Enabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set PcieOptionROMs

To specify whether the server can use the PCIe Option ROM expansion slots, use the set PcieOptionROMs command.

set PcieOptionROMs { Disabled | Enabled }

Syntax Description

Disabled	The PCIe Option ROMs are not available.
Enabled	The PCIe Option ROMs are available.

Command Default

The PCIe Option ROMs are available.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(5)	This command was introduced.

Examples

This example specifies that the PCIe Option ROMs are not available and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set PcieOptionROMs Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set PcieSlotnOptionROM

To specify whether a PCIe Option ROM expansion slot is available to the server, use the set PcieSlotnOptionROM command.

set PcieSlotnOptionROM { Disabled | Enabled }

Syntax Description

n	The number or letter of the PCIe slot.
Disabled	The specified expansion slot is not available.
Enabled	The specified expansion slot is available.

Command Default

The PCIe Option ROM expansion slot is available.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(5)	This command was introduced.

Usage Guidelines

Use this command to specify the availability of the PCIe Option ROM expansion slot designated by n in the command name set PcieSlotnOptionROM.

Examples

This example specifies that PCIe Option ROM expansion slot 2 is not available and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set PcieSlot2OptionROM Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set PciOptRomsDisable

To specify whether the server can use the PCIe Option ROM expansion slots, use the set PciOptRomsDisable command.

set PciOptRomsDisable { Disabled | Enabled }

Syntax Description

Disabled	The PCIe Option ROMs are not available.
Enabled	The PCIe Option ROMs are available.

Command Default

The PCIe Option ROMs are available.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example specifies that the PCIe Option ROMs are not available and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set PciOptRomsDisable Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set peak-power

To specify the maximum number of watts that can be allocated to the server, use the set peak-power command.

set peak-power watts

Syntax Description

watts

The maximum number of watts that can be allocated to the server.

Command Default

Zero watts are allocated.

Command Modes

Power cap (/power-cap)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Use this command to specify the maximum number of watts that can be allocated to this server. Enter a number of watts within the range defined by the Minimum Configurable Limit field and the Maximum Configurable Limit field of the show power-cap detail command output. These fields are determined by the server model.

If the server requests more power than specified in this command, the system takes the action defined by the set non-compliance-action command.

Examples

This example sets the maximum number of watts allocated to 1000 and commits the transaction:

Server# scope power-cap
Server /power-cap # set enabled yes
Server /power-cap *# set peak-power 1000
Server /power-cap *# set non-compliance-action throttle
Server /power-cap *# commit
Server /power-cap #  show detail
    Cur Consumption (W): 688
    Max Consumption (W): 1620
    Min Consumption (W): 48
    Minimum Configurable Limit (W): 500
    Maximum Configurable Limit (W): 2000
    Power Cap Enabled: yes
    Peak Power: 1000
    Non Compliance Action: throttle

Server /power-cap #

Related Commands

Command	Description
set non-compliance-action
show power-cap

set penalty-time

To specify a blocking time after multiple login failures, use the set penalty-time command.

set penalty-time penalty-seconds

Syntax Description

penalty-seconds

The number of seconds the user remains locked out after exceeding the maximum number of login attempts within the specified time window. The range of valid values is 300 to 900.

Command Default

The default blocking time is 300 seconds.

Command Modes

IP blocking (/cimc/network/ipblocking)

Command History

Release	Modification
1.0(1X)	This command was introduced.

Examples

This example sets the IP blocking time to 600 seconds:

server# scope cimc
server /cimc # scope network
server /cimc/network # scope ipblocking
server /cimc/network/ipblocking # set enable yes
server /cimc/network/ipblocking* # set penalty-time 600
server /cimc/network/ipblocking* # commit
server /cimc/network/ipblocking #

Related Commands

Command	Description
set fail-count
show ipblocking

set persistent-lun-binding

To enable or disable the persistent binding for the vHBA, use the set persistent-lun-binding command.

set persistent-lun-binding { disable | enable }

Syntax Description

disable	Disables persistent-lun binding.
enable	Enables persistent-lun binding.

Command Default

None

Command Modes

Persistent binding (/chassis/adapter/host-fc-if/perbi)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to enable the persistent-lun binding of the host Fibre Channel interface:

Server# scope chassis
Server/chassis # scope adapter 1
Server/chassis/adapter # scope host-fc-if fc0
Server/chassis/adapter/host-fc-if # scope perbi
Server/chassis/adapter/host-fc-if/perbi # set persistent-lun-binding enable
Server/chassis/adapter/host-fc-if/perbi *# commit
Server/chassis/adapter/host-fc-if/perbi #

Related Commands

None

set platform-event-enabled

To enable or disable platform event alerts, use the set platform-event-enabled command.

set platform-event-enabled { no | | yes }

Syntax Description

no	Disables platform event alerts.
yes	Enables platform event alerts.

Command Default

Platform event alerts are enabled.

Command Modes

Fault (/fault)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example enables platform event alerts:

server# scope fault
server /fault # set platform-event-enabled yes
server /fault* # commit
server /fault #

Related Commands

Command	Description
show fault
show pef

set plogi-retries

To set the port login (PLOGI) retries value, use the set plogi-retries command.

set plogi-retries count

Syntax Description

count

Specifies the number of times that the system tries to log in to the fabric after the first failure. The range is 0 and 255.

Command Default

The default is 8 retries.

Command Modes

Port-p-logi (/chassis/adapter/host-fc-if/port-p-logi)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the plogi-retries of the host Fibre Channel interface:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # scope port-p-logi
Server /chassis/adapter/host-fc-if/port-p-logi # set plogi-retries 03
Server /chassis/adapter/host-fc-if/port-p-logi *# commit
Server /chassis/adapter/host-fc-if/port-p-logi #

Related Commands

Command	Description
set plogi-timeout

set plogi-timeout

To set the port login (PLOGI) timeout value of the host Fibre Channel interface, use the set plogi-timeout command.

set plogi-timeout msec

Syntax Description

msec	Specifies the number of milliseconds that the system waits before it tries to log in again. The range is 1 to 255000.

Command Default

The default is 2000 milliseconds.

Command Modes

Port-p-logi (/chassis/adapter/host-fc-if/port-p-logi)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the port login (PLOGI) timeout value of the host Fibre Channel Interface:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if
Server/chassis/adapter/host-fc-if # scope port-p-logi
Server/chassis/adapter/host-fc-if/port-p-logi # set plogi-timeout 203
Server/chassis/adapter/host-fc-if/port-p-logi *# commit
Server/chassis/adapter/host-fc-if/port-p-logi #

Related Commands

Command	Description
set port-plogi-retries

set policy

To specify the action to be taken when chassis power is restored, use the set policy command.

set policy { power-off | power-on | restore-last-state }

Syntax Description

power-off	Server power will remain off until manually turned on.
power-on	Server power will be turned on when chassis power is restored.
restore-last-state	Server power will return to the state before chassis power was lost.

Command Default

The default action is power-off.

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Use this command to specify the action to be taken when chassis power is restored after an outage.

When the selected action is power-on, you can select a delay in the restoration of power to the server.

Examples

This example sets the power restore policy to power-on with a fixed delay of 180 seconds (3 minutes) and commits the transaction:

Server# scope chassis
Server /chassis # set policy power-on
Server /chassis *# set delay fixed
Server /chassis *# set delay-value 180
Server /chassis *# commit
Server /chassis #  show detail
Chassis:
    Power: on
    Serial Number: QCI1404A1IT
    Product Name: UCS C200 M1
    PID : R200-1120402
    UUID: 01A6E738-D8FE-DE11-76AE-8843E138AE04
    Locator LED: off
    Description: Testing power restore
    Power Restore Policy: power-on
    Power Delay Type: fixed
    Power Delay Value(sec): 180

Server /chassis #

Related Commands

Command	Description
set delay
set delay-value

set port-down-io-retry-count

To set the port-down-io-retry-count of the host Fibre Channel interface, use the set port-down-io-retry-count command.

set port-down-io-retry-count count

Syntax Description

count

The number of times an I/O request to a port is returned because the port is busy before the system decides the port is unavailable. The range is 0 to 255.

Command Default

The default is 8 retries.

Command Modes

Error-recovery (/chassis/adapter/host-fc-if/error-recovery)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the port-down-io-retry-count:

Server# scope chassis
Server /chassis/ # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0 
Server /chassis/adapter/host-fc-if/ # scope error-recovery
Server /chassis/adapter/host-fc-if/error-recovery # set port-down-io-retry-count 200
Server /chassis/adapter/host-fc-if/error-recovery *# commit
Committed host-fc-if fc0 settings will take effect upon the next server reset
Server /chassis/adapter/host-fc-if/error-recovery #

Related Commands

Command	Description
set port-down-timeout

set port-down-timeout

To set the port-down-timeout, use the set port-down-timeout command.

set port-down-timeout msec

Syntax Description

msec	Specifies the number of milliseconds the uplink port should be offline before it informs the system that the uplink port is down and fabric connectivity has been lost. The range is 0 to 240000.

Command Default

The default is 10000 milliseconds.

Command Modes

Error-recovery (/chassis/adapter/host-fc-if/error-recovery)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the port-down-io-retry-timeout:

Server# scope chassis
Server /chassis/ # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0 
Server /chassis/adapter/host-fc-if # scope error-recovery
Server /chassis/adapter/host-fc-if/error-recovery # set port-down-timeout 9343
Server /chassis/adapter/host-fc-if/error-recovery *# commit
Committed host-fc-if fc0 settings will take effect upon the next server reset
Server /chassis/adapter/host-fc-if/error-recovery #

Related Commands

Command	Description
set port-down-io-retry-count

set port-profile (host-eth-if)

To specify a port profile that should be associated with the vNIC, use the set port-profile command in host-eth-if mode.

set port-profile name

Syntax Description

name	The name of a port profile.

Command Default

None

Command Modes

Ethernet host interface (/chassis/adapter/host-eth-if)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Note

To use this command, you must enable NIV mode for the adapter.

The name must be a port profile defined on the switch to which this server is connected.

Examples

This example shows how to specify a port profile on interface eth0 on adapter card 1:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # set niv-mode enabled
Server /chassis/adapter *# scope host-eth-if eth0
Server /chassis/adapter/host-eth-if *# set port-profile TestProfile5
Server /chassis/adapter/host-eth-if *# commit
Server /chassis/adapter/host-eth-if #

Related Commands

Command	Description
set niv-mode
show port-profiles

set port-profile (network)

To configure the server to connect to the network using a port profile, use the set port-profile command in network mode.

set port-profile name

Syntax Description

name

Specifies the port profile CIMC should use to configure the management interface, the virtual Ethernet, and the VIF on supported adapter cards such as the Cisco UCS VIC1225 Virtual Interface Card.

Enter up to 80 alphanumeric characters. You cannot use spaces or other special characters except for - (hyphen) and _ (underscore). In addition, the port profile name cannot begin with a hyphen.

Note

The port profile must be defined on the switch to which this server is connected.

Command Default

None

Command Modes

network (/network)

Command History

Release	Modification
1.4(6)	This command was introduced.

Usage Guidelines

Use this command to configure the network using a port profile.

Examples

This example connects to port profile abcde12345:

Server# scope cimc
Server /cimc # scope network
Server /cimc/network # set port-profile abcde12345
Server /cimc/network *# commit
Server /cimc/network # show detail
Network Setting:
    IPv4 Address: 10.193.66.174
    IPv4 Netmask: 255.255.248.0
    IPv4 Gateway: 10.193.64.1
    DHCP Enabled: no
    Obtain DNS Server by DHCP: no
    Preferred DNS: 0.0.0.0
    Alternate DNS: 0.0.0.0
    VLAN Enabled: no
    VLAN ID: 1
    VLAN Priority: 0
    Port Profile: abcde12345
    Hostname: Server
    MAC Address: 50:3D:E5:9D:63:3C
    NIC Mode: dedicated
    NIC Redundancy: none   

Server /cimc/network #

set POSTErrorPause

To specify the action when the server encounters a critical error during power-on self test (POST), use the set POSTErrorPause command.

set POSTErrorPause { Disabled | Enabled }

Syntax Description

Disabled	The BIOS continues to attempt to boot the server when a critical error occurs during POST.
Enabled	The BIOS pauses the attempt to boot the server and opens the Error Manager when a critical error occurs during POST.

Command Default

The BIOS continues to attempt to boot the server when a critical error occurs during POST.

Command Modes

Main BIOS (/bios/main)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example configures the boot to pause when a critical error occurs during POST and commits the transaction:

Server# scope bios
Server /bios # scope main
Server /bios/main # set POSTErrorPause Enabled
Server /bios/main *# commit
Server /bios/main *# show detail
Set-up parameters:
    Boot option retry: Disabled
    POST Error Pause: Enabled

Server /bios/main #

Related Commands

Command	Description
show main

set preferred-dns-server

To specify the IP address of the primary DNS server, use the set preferred-dns-server command.

set preferred-dns-server dns1-ipv4-address

Syntax Description

dns1-ipv4-address

The IP address of the primary DNS server.

Command Default

None

Command Modes

Network (/cimc/network)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example specifies the IP address of the primary DNS server:

server# scope cimc
server /cimc # scope network
server /cimc/network # set preferred-dns-server 192.0.20.1
server /cimc/network* # commit
server /cimc/network #

Related Commands

Command	Description
set alternate-dns-server
show network

set privilege-level

To specify the highest privilege level that can be assigned to an IPMI session, use the set privilege-level command.

set privilege-level { admin | readonly | user }

Syntax Description

admin	IPMI users can perform all available actions.
readonly	IPMI users can view information but cannot make any changes.
user	IPMI users can perform some functions but cannot perform administrative tasks.

Command Default

IPMI users can perform all available actions.

Command Modes

IPMI (/ipmi)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to specify the highest privilege level that can be assigned to an IPMI session on this server. This can be one of the following levels:

admin — IPMI users can perform all available actions. If you select this option, IPMI users with the "Administrator" user role can create admin, user, and read-only sessions on this server.
readonly — IPMI users can view information but cannot make any changes. If you select this option, IPMI users with the "Administrator", "Operator", or "User" user roles can only create read-only IPMI sessions, regardless of their other IPMI privileges.
user — IPMI users can perform some functions but cannot perform administrative tasks. If you select this option, IPMI users with the "Administrator" or "Operator" user role can create user and read-only sessions on this server.

Examples

This example sets the highest privilege level that can be assigned to an IPMI session to read-only:

server# scope ipmi
server /ipmi # set enabled yes
server /ipmi* # set privilege-level readonly
server /ipmi* # commit
server /ipmi #

Related Commands

Command	Description
show ipmi

set ProcessorC1eEnable

To specify whether the CPU transitions to its minimum frequency when entering the C1 state, use the set ProcessorC1eEnable command.

set ProcessorC1eEnable { Disabled | Enabled }

Syntax Description

Disabled	The CPU continues to run at its maximum frequency in the C1 state.
Enabled	The CPU transitions to its minimum frequency. This option saves the maximum amount of power in the C1 state.

Command Default

The CPU transitions to its minimum frequency in C1 state.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to specify whether the CPU transitions to its minimum frequency when entering the C1 state. Enabling this option saves the maximum amount of power in the C1 state.

Note

This command is operative only if the set ProcessorCcxEnable command is set to Enabled.

Examples

This example configures the CPU to run at its maximum frequency in the C1 state and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set ProcessorC1eEnable Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set ProcessorCcxEnable
show advanced

set ProcessorC1EReport

To specify whether the CPU transitions to its minimum frequency when entering the C1 state, use the set ProcessorC1EReport command.

set ProcessorC1EReport { Disabled | Enabled }

Syntax Description

Disabled	The CPU continues to run at its maximum frequency in the C1 state.
Enabled	The CPU transitions to its minimum frequency. This option saves the maximum amount of power in the C1 state.

Command Default

The CPU transitions to its minimum frequency in C1 state.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(5)	This command was introduced.

Usage Guidelines

Use this command to specify whether the CPU transitions to its minimum frequency when entering the C1 state. Enabling this option saves the maximum amount of power in the C1 state.

Examples

This example configures the CPU to run at its maximum frequency in the C1 state and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set ProcessorC1EReport Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set ProcessorC3Report

To specify whether the BIOS sends the C3 report to the operating system, use the set ProcessorC3Report command.

set ProcessorC3Report { Disabled | ACPI_C2 | ACPI_C3 }

Syntax Description

Disabled	The BIOS does not send the C3 report.
ACPI_C2	The BIOS sends the C3 report using the ACPI C2 format.
ACPI_C3	The BIOS sends the C3 report using the ACPI C3 format.

Command Default

The BIOS does not send the C3 report.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Use this command to specify whether the BIOS sends the C3 report to the operating system. When the OS receives the report, it can transition the processor into the lower C3 power state to decrease energy usage while maintaining optimal processor performance. This can be one of the following:

Disabled—The BIOS does not send the C3 report.
ACPI_C2—The BIOS sends the C3 report using the ACPI C2 format, allowing the OS to transition the processor to the C3 low power state.
ACPI_C3—The BIOS sends the C3 report using the ACPI C3 format, allowing the OS to transition the processor to the C3 low power state.

Examples

This example specifies that the BIOS sends the C3 report using the ACPI C3 format and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set ProcessorC3Report ACPI_C3
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set ProcessorC6Report

To specify whether the BIOS sends the C6 report to the operating system, use the set ProcessorC6Report command.

set ProcessorC6Report { Disabled | Enabled }

Syntax Description

Disabled	The BIOS does not send the C6 report.
Enabled	The BIOS sends the C6 report.

Command Default

The BIOS sends the C6 report.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Use this command to specify whether the BIOS sends the C6 report to the operating system. When the OS receives the report, it can transition the processor into the lower C6 power state to decrease energy usage while maintaining optimal processor performance. This can be one of the following:

Disabled—The BIOS does not send the C6 report.
Enabled—The BIOS sends the C6 report, allowing the OS to transition the processor to the C6 low power state.

Examples

This example specifies that the BIOS does not send the C6 report and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set ProcessorC6Report Disable
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set ProcessorC7Report

To specify whether the processor sends the C7 report to the operating system, use the set ProcessorC7Report command.

set ProcessorC7Report { Disabled | Enabled }

Syntax Description

Disabled	The processor does not send the C7 report.
Enabled	The processor sends the C7 report.

Command Default

The processor does not send the C7 report.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(1)	This command was introduced.

Examples

This example specifies that the processor sends the C7 report and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set ProcessorC7Report Enable
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set ProcessorCcxEnable

To specify whether the system can enter a power savings mode during idle periods, use the set ProcessorCcxEnable command.

set ProcessorCcxEnable { Disabled | Enabled }

Syntax Description

Disabled	The system remains in high performance state even when idle.
Enabled	The system can reduce power to system components such as the DIMMs and CPUs.

Command Default

The system can reduce power to system components when idle.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to specify whether the system can enter a power savings mode during idle periods. The amount of power reduction is specified by the set PackageCStateLimit command.

Examples

This example specifies that the system remains in high performance state even when idle and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set ProcessorCcxEnable Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set QPILinkFrequency

To specify the Intel QuickPath Interconnect (QPI) link frequency in gigatransfers per second (GT/s), use the set QPILinkFrequency command.

set QPILinkFrequency { Auto | 6.4_GT/s | 7.2_GT/s | 8.0_GT/s }

Syntax Description

Auto	The CPU determines the QPI link frequency.
6.4_GT/s	The QPI link frequency is 6.4 GT/s.
7.2_GT/s	The QPI link frequency is 7.2 GT/s.
8.0_GT/s	The QPI link frequency is 8.0 GT/s.

Command Default

The CPU determines the QPI link frequency.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(5)	This command was introduced.

Examples

This example specifies that the QPI link frequency is 6.4 GT/s and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set QPILinkFrequency 6.4_GT/s
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set raid-primary-member

To specify the slot in which the primary copy of the data resides, use the set raid-primary-member command.

set raid-primary-member { slot1 | slot2 }

Syntax Description

slot1	The primary copy of the data resides in slot 1.
slot2	The primary copy of the data resides in slot 2.

Command Default

The primary copy of the data resides in slot 1.

Command Modes

FlexFlash operational profile (/chassis/flexflash/operational-profile)

Command History

Release	Modification
1.3(3)	This command was introduced.

Usage Guidelines

Use this command to specify the slot in which the primary copy of the data resides.

Note

Currently, Cisco Flexible Flash cards are supported only in slot 1.

Examples

This example shows how to specify that the primary copy of the data resides in slot 1:

Server# scope chassis
Server /chassis # scope flexflash FlexFlash-0
Server /chassis/flexflash # scope operational-profile
Server /chassis/flexflash/operational-profile # set raid-primary-member slot1
Server /chassis/flexflash/operational-profile *# commit
Server /chassis/flexflash/operational-profile #

Related Commands

Command	Description
scope operational-profile

set raid-secondary-role

To set the RAID secondary role, use the set raid-secondary-role command.

set raid-secondary-role active initializing

Syntax Description

active	Sets the secondary role as Active.
initializing	Sets the secondary role as Initializing.

Command Default

None

Command Modes

Operational profile (/chassis/flexflash/operational-profile)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

None

Examples

This example shows how to set the RAID secondary role:

Server # scope chassis
Server /chassis # scope flexflash FlexFlash-0
Server /chassis/flexflash # scope operational-profile 
Server /chassis/flexflash/operational-profile # set raid-secondary-role active
Server /chassis/flexflash/operational-profile* # commit
Server /chassis/flexflash/operational-profile #

Related Commands

Command	Description
scope operational-profile
set raid-primary-member
set read-error-count-threshold
set virtual-drives-enabled
set write-error-count-threshold

set RankInterLeave

To specify how the CPU performs interleaving of physical ranks of memory, use the set RankInterLeave command.

set RankInterLeave { Auto | 1_Way | 2_Way | 4_Way | 8_Way }

Syntax Description

Auto	The CPU determines what interleaving is done.
1_Way	Some rank interleaving is used.
2_Way	Additional rank interleaving is used.
4_Way	Additional rank interleaving is used.
8_Way	The maximum amount of rank interleaving is used.

Command Default

The CPU determines what interleaving is done.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(5)	This command was introduced.

Usage Guidelines

Use this command to specify how the CPU interleaves physical ranks of memory so that one rank can be accessed while another is being refreshed.

Examples

This example configures the CPU to perform the maximum amount of rank interleaving and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set RankInterLeave 8_Way
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set rate-limit

To specify a maximum data rate for the host interface, use the set rate-limit command.

set rate-limit { off | rate }

Syntax Description

off	Rate limiting is disabled.
rate	Specifies the rate limit in Mbps. The range is 1 to 10000.

Command Default

Rate limiting is disabled.

Command Modes

Ethernet host interface (/chassis/adapter/host-eth-if)

Fibre Channel host interface (/chassis/adapter/host-fc-if)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example shows how to specify a rate limit of 500 Mbps on interface eth0 on adapter card 1:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # set rate-limit 500
Server /chassis/adapter/host-eth-if *# commit
Server /chassis/adapter/host-eth-if #

Related Commands

Command	Description
show host-eth-if

set read-error-count-threshold

To specify the number of read errors that can occur before CIMC decides that the Cisco Flexible Flash card has failed, use the set read-error-count-threshold command.

set read-error-count-threshold value

Syntax Description

value

Number between 0 and 255. The value indicates the number of read errors that can occur before CIMC decides that the Cisco Flexible Flash card has failed.

Command Default

None

Command Modes

FlexFlash Operational Profile (/chassis/flexflash/operational-profile)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

Use this command to specify the number of read errors that can occur before CIMC decides that the Cisco Flexible Flash card has failed. Once this threshold has been reached, you must reset the Cisco Flexible Flash card before CIMC attempts to access it again.

Enter an integer between 1 and 255, or enter 0 (zero) if you want CIMC to continue using the card no matter how many errors it encounters.

Examples

This example shows how to set the read error threshold count to 100 for the Cisco Flexible Flash card:

Server # scope chassis
Server /chassis # scope flexflash FlexFlash-0
Server /chassis/flexflash # scope operational-profile
Server /chassis/flexflash/operational-profile # set read-error-count-threshold 100
Server /chassis/flexflash/operational-profile* # commit
Server /chassis/flexflash/operational-profile #

Related Commands

Command	Description
set raid-primary-member
set raid-secondary-role
set write-error-count-threshold
set virtual-drives-enabled

set redundancy

To specify the server NIC redundancy mode when the NIC mode is Shared LOM, use the set redundancy command.

set redundancy { none | active-active | active-standby }

Syntax Description

none	The LAN On Motherboard (LOM) Ethernet ports operate independently and do not fail over if there is a problem.
active-active	If supported, all LOM Ethernet ports are utilized.
active-standby	If one LOM Ethernet port fails, traffic fails over to another LOM port.

Command Default

None

Command Modes

Network (/cimc/network)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example sets the server NIC redundancy mode to active-standby:

server# scope cimc
server /cimc # scope network
server /cimc/network # set redundancy active-standby
server /cimc/network* # commit
server /cimc/network #

Related Commands

Command	Description
set mode
show network

set remote-ip

To set a remote server IP address to download the technical support data, use the set remote-ip command.

set remote-ip value

Syntax Description

value

IP address of the remote server. The format is X.X.X.X.

Command Default

None

Command Modes

Technical support (/cimc/tech-support)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

Specifies the IP address of the remote server on which the support data file should be stored.

Perform this task along with set remote-path and set remote-protocol when requested by the Cisco Technical Assistance Center (TAC). This utility creates a summary report containing configuration information, logs and diagnostic data that will help TAC in troubleshooting and resolving technical issues.

You must set a remote username and password if you select the remote protocol as FTP, SFTP, or SCP.

Examples

This example shows how to set the IP address of a TFTP server on which the support data file must be stored:

Server # scope cimc
Server /cimc # scope tech-support
Server /cimc/tech-support # set remote-ip 209.165.200.225
Server /cimc/tech-support* # commit
Server /cimc/tech-support #

Related Commands

Command	Description
set remote-path
set remote-password
set remote-protocol
set remote-username

set remote-password

To set a password for the remote server username, use the set remote-password command.

set remote-password

This command has no keywords or arguments.

Command Default

None

Command Modes

Tech support (/cimc/tech-support)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must set a username and password for the remote server if you select the remote protocol as FTP, SFTP, or SCP.

Perform this task along with set remote-ip, set remote-path and set remote-username commands when requested by the Cisco Technical Assistance Center (TAC). This utility creates a summary report containing configuration information, logs and diagnostic data that will help TAC in troubleshooting and resolving technical issues.

Examples

This example shows how to set the password for the remote server username:

Server # scope cimc
Server /cimc # scope tech-support
Server /cimc/tech-support # set remote-password

Please enter remote-password: **** 
Please confirm remote-password: ****

Server /cimc/tech-support* # commit
Server /cimc/tech-support #

Related Commands

Command	Description
set remote-ip
set remote-path
set remote-username
set remote-protocol

set remote-path

To set a file path on a remote server for the summary report in the tech-support command mode, use the set remote-path command.

set remote-path value

Syntax Description

value

The file path to the summary report.

Command Default

None

Command Modes

Tech Support (/cimc/tech-support)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

Perform this task along with set remote-ip when requested by the Cisco Technical Assistance Center (TAC). This utility creates a summary report containing configuration information, logs and diagnostic data that will help TAC in troubleshooting and resolving technical issues.

Examples

This example shows how to set the file path on a TFTP server on which the support data file must be stored:

Server # scope cimc
Server /cimc # scope tech-support
Server /cimc/tech-support # set remote-path sample_filename.tar.gz
Server /cimc/tech-support* # commit
Server /cimc/tech-support #

Related Commands

Command	Description
set remote-ip
set remote-password
set remote-protocol
set remote-username

set remote-protocol

To specify a protocol to connect to the remote server in the tech-support command mode, use the set remote-protocol command.

set remote-protocol value

Syntax Description

value

Specifies the protocol to connect to the remote server. It can be one of the following values:

tftp
ftp
sftp
scp
http

Command Default

None

Command Modes

Tech-support (/cimc/tech-support)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

Perform this task along with set remote-ip and set remote-path commands when requested by the Cisco Technical Assistance Center (TAC). This utility creates a summary report containing configuration information, logs and diagnostic data that will help TAC in troubleshooting and resolving technical issues.

You must set a remote username and password if you select the remote protocol as FTP, SFTP, or SCP.

Examples

This example shows how to set the remote protocol to TFTP:

Server # scope cimc
Server /cimc # scope tech-support
Server /cimc/tech-support # set remote-protocol tftp
Server /cimc/tech-support* # commit
Server /cimc/tech-support #

Related Commands

Command	Description
set remote-ip
set remote-path
set remote-password
set remote-username

set remote-syslog-severity

To specify the lowest level of CIMC log messages that will be sent to the remote syslog server, use the set remote-syslog-severity command.

set remote-syslog-severity level

Syntax Description

level

The lowest level of messages that will be sent to the remote syslog server. See the Usage Guidelines for valid values.

Command Default

Messages of level Warning and higher are sent.

Command Modes

CIMC log (/cimc/log)

Command History

Release	Modification
1.4(3)	This command was introduced.

Usage Guidelines

The severity level can be one of the following, in decreasing order of severity:

emergency
alert
critical
error
warning
notice
informational
debug

CIMC does not send any log messages with a severity below the selected severity. For example, if you select error, CIMC will send all messages with the severity Emergency, Alert, Critical, or Error. It will not send Warning, Notice, Informational, or Debug messages.

Examples

This example shows how to configure the sending of CIMC log entries with a minimum severity level of Warning:

Server# scope cimc
Server /cimc # scope log
Server /cimc/log # set remote-syslog-severity warning
Server /cimc/log *# commit
Server /cimc/log #

Related Commands

Command	Description
show remote-syslog-severity

set remote-username

To set a username to connect to the remote server that stores the technical support data, use the set remote-username command.

set remote-username username

Syntax Description

username

The user name to connect to the remote server.

Command Default

None

Command Modes

Tech support (/cimc/tech-support)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must set a remote username and password if you select the remote protocol as FTP, SFTP, or SCP.

Perform this task along with set remote-ip, set remote-path and set remote-password commands when requested by the Cisco Technical Assistance Center (TAC). This utility creates a summary report containing configuration information, logs and diagnostic data that will help TAC in troubleshooting and resolving technical issues.

Examples

This example shows how to set the remote user name:

Server # scope cimc
Server /cimc # scope tech-support
Server /cimc/tech-support # set remote-username sample_user
Server /cimc/tech-support* # commit
Server /cimc/tech-support #

Related Commands

Command	Description
set remote-ip
set remote-path
set remote-password
set remote-protocol

set resource-allocation-timeout

To set the the resource allocation timeout value (RATOV), use the set error-detect-timeout command.

set resource-allocation-timeout msec

Syntax Description

msec	Specifies the resource allocation timeout value (RATOV), the number of milliseconds to wait before the system assumes that a resource cannot be properly allocated. The range is 5000 to 100000; the default is 10000 milliseconds.

Command Default

The default is 10000 milliseconds.

Command Modes

Fibre Channel host interface (/chassis/adapter/host-fc-if)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the resource allocation timeout value to 5000 milliseconds:

Server# scope chassis
Server /chassis/ # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0 
Server /chassis/adapter/host-fc-if # set resource-allocation-timeout 5000
Server /chassis/adapter/host-fc-if *# commit
Server /chassis/adapter/host-fc-if #

Related Commands

Command	Description
set error-detect-timeout

set role

To specify a user role, use the set role command.

set role { admin | readonly | user }

Syntax Description

admin	The user can perform all configuration and control tasks.
readonly	The user can only read configuration and status.
user	The user can perform control tasks but cannot change the configuration.

Command Default

None

Command Modes

LDAP role group (/ldap/role-group)

User (/user)

Command History

Release	Modification
1.0(1)	This command was introduced.
1.4(1)	This command was added in the LDAP role group command mode.

Usage Guidelines

Use this command to specify the permission level (role) for a user. A user can be assigned one of the following roles:

admin—The user can perform all actions available.
user—The user can perform the following tasks:
- View all information
- Manage the power control options such as power on, power cycle, and power off
- Launch the KVM console and virtual media
- Clear all logs
- Toggle the locator LED
readonly—The user can view information but cannot make any changes.

Examples

This example configures a user name, password, and role for user number 15:

Server# scope user 15
Server /user # set enabled yes
Server /user* # set name user15
Server /user* # set password ex4mpl3
Server /user* # set role readonly
Server /user* # commit
Server /user #

Related Commands

Command	Description
show user

set rq-count

To set the receive queue count of the host Ethernet interface, use the set rq-count command.

set rq-count count

Syntax Description

count

The number of receive queue resources to allocate. The range is 1 to 256.

Command Default

The default is 4.

Command Modes

Receive queue (/chassis/adapter/host-eth-if/recv-queue)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the number of receive queue resources to allocate:

Server# scope chassis
Server /chassis/ # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0 
Server /chassis/adapter/host-eth-if # scope recv-queue
Server /chassis/adapter/host-eth-if/recv-queue # set rq-count 3
Server /chassis/adapter/host-eth-if/recv-queue *# commit
Committed host-eth-if eth0 settings will take effect upon the next server reset
Server /chassis/adapter/host-eth-if/recv-queue #

Related Commands

Command	Description
set rq-ring-size

set rq-ring-size

To set the receive queue ring size, use the set rq-ring-size command.

set rq-ring-size size

Syntax Description

size	The number of descriptors in the receive queue. The range is 64 to 4094; the default is 512.

Command Default

The default is 512.

Command Modes

Receive queue (/chassis/adapter/host-eth-if/recv-queue)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the number of descriptors in the receive queue:

Server# scope chassis
Server /chassis/ # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # scope recv-queue
Server /chassis/adapter/host-eth-if/recv-queue # set eth-rq-ring-size 68
Server /chassis/adapter/host-eth-if/recv-queue *# commit
Committed host-eth-if eth0 settings will take effect upon the next server reset
Server /chassis/adapter/host-eth-if/recv-queue #

Related Commands

Command	Description
set rq-count

set rss

To enable or disable Receive-side Scaling (RSS), use the set rss command.

set rss { disable | enable }

Syntax Description

disable	Disables RSS.
enable	Enables RSS.

Command Default

The default is enable for the two default vNICs and disable for user-created vNICs.

Command Modes

RSS (/chassis/adapter/host-eth-if/rss)

Command History

Release	Modification
1.2(1)	This command was introduced.

Usage Guidelines

Use this command to enable or disable RSS, which allows the efficient distribution of network receive processing across multiple CPUs in multiprocessor systems.

Examples

This example shows how to disable RSS:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # scope rss
Server /chassis/adapter/host-eth-if/rss # set rss disable
Server /chassis/adapter/host-eth-if/rss *# commit
Committed host-eth-if eth0 settings will take effect upon the next server reset
Server /chassis/adapter/host-eth-if/rss #

Related Commands

Command	Description
set rss-hash-ipv4
set rss-hash-ipv6

set rss-hash-ipv4

To enable or disable the IPv4 RSS of the host Ethernet interface, use the set rss-hash-ipv4 command.

set rss-hash-ipv4 { disable | enable }

Syntax Description

disable	Disables IPv4 RSS.
enable	Enables IPv4 RSS.

Command Default

The default is enable.

Command Modes

RSS (/chassis/adapter/host-eth-if/rss)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the rss-hash-ipv4:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # scope rss
Server /chassis/adapter/host-eth-if/rss # set rss-hash-ipv4 disable
Server /chassis/adapter/host-eth-if/rss *# commit
Committed host-eth-if eth0 settings will take effect upon the next server reset
Server /chassis/adapter/host-eth-if/rss #

Related Commands

Command	Description
set rss-hash-ipv6
set rss

set rss-hash-ipv6

To enable or disable the IPv6 RSS of the host Ethernet interface, use the set rss-hash-ipv6 command.

set rss-hash-ipv6 { disable | enable }

Syntax Description

disable	Disables IPv6 RSS.
enable	Enables IPv6 RSS.

Command Default

The default is enable.

Command Modes

RSS (/chassis/adapter/host-eth-if/rss)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the rss-hash-ipv6:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # scope rss
Server /chassis/adapter/host-eth-if/rss # set rss-hash-ipv6 disable
Server /chassis/adapter/host-eth-if/rss *# commit
Committed host-eth-if eth0 settings will take effect upon the next server reset
Server /chassis/adapter/host-eth-if/rss #

Related Commands

Command	Description
set rss-hash-ipv4
set rss

set rss-hash-ipv6-ex

To enable or disable the IPv6 Extension RSS of the host Ethernet interface, use the set rss-hash-ipv6-ex command.

set rss-hash-ipv6-ex { disable | enable }

Syntax Description

disable	Disables IPv6 extension RSS.
enable	Enables IPv6 extension RSS.

Command Default

The default is disable.

Command Modes

RSS (/chassis/adapter/host-eth-if/rss)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the rss-hash-ipv6-ex:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0 
Server /chassis/adapter/host-eth-if # scope rss
Server /chassis/adapter/host-eth-if/rss # set rss-hash-ipv6-ex disable
Server /chassis/adapter/host-eth-if/rss *# commit
Committed host-eth-if eth0 settings will take effect upon the next server reset
Server /chassis/adapter/host-eth-if/rss #

Related Commands

Command	Description
set rss-hash-ipv6
set rss

set rss-hash-tcp-ipv4

To enable or disable TCP/IPv4 RSS on the host Ethernet interface, use the set rss-hash-tcp-ipv4 command.

set rss-hash-tcp-ipv4 { disable | enable }

Syntax Description

disable	Disables TCP/IPv4 RSS.
enable	EnablesTCP/IPv4 RSS.

Command Default

The default is enable.

Command Modes

RSS (/chassis/adapter/host-eth-if/rss)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to enable TCP/IPv4 RSS:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0 
Server /chassis/adapter/host-eth-if # scope rss
Server /chassis/adapter/host-eth-if/rss # set rss-hash-tcp-ipv4 enable
Server /chassis/adapter/host-eth-if/rss *# commit
Committed host-eth-if eth0 settings will take effect upon the next server reset
Server /chassis/adapter/host-eth-if/rss #

Related Commands

Command	Description
set rss
set rss-hash-tcp-ipv6

set rss-hash-tcp-ipv6

To enable or disable the TCP/IPv6 RSS of the host Ethernet interface, use the set rss-hash-tcp-ipv6 command.

set rss-hash-tcp-ipv6 { disable | enable }

Syntax Description

disable	Disables TCP/IPv6 RSS.
enable	Enables TCP/IPv6 RSS.

Command Default

The default is enable.

Command Modes

RSS (/chassis/adapter/host-eth-if/rss)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the rss-hash-tcp-ipv6:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # scope rss
Server /chassis/adapter/host-eth-if/rss # set rss-hash-tcp-ipv6 disable
Server /chassis/adapter/host-eth-if/rss *# commit
Committed host-eth-if eth0 settings will take effect upon the next server reset
Server /chassis/adapter/host-eth-if/rss #

Related Commands

Command	Description
set rss-hash-tcp-ipv4
set rss

set rss-hash-tcp-ipv6-ex

To set the TCP/IPv6 Extension RSS of the host Ethernet interface, use the set rss-hash-tcp-ipv6-ex command.

set rss-hash-tcp-ipv6-ex { disable | enable }

Syntax Description

disable	Disables TCP/IPv6 extension RSS.
enable	Enables TCP/IPv6 extension RSS.

Command Default

The default is disable.

Command Modes

RSS (/chassis/adapter/host-eth-if/rss)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the rss-hash-tcp-ipv6-ex:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # scope rss
Server /chassis/adapter/host-eth-if/rss # set rss-hash-tcp-ipv6-ex
Server /chassis/adapter/host-eth-if/rss *# commit
Committed host-eth-if eth0 settings will take effect upon the next server reset
Server /chassis/adapter/host-eth-if/rss #

Related Commands

Command	Description
set rss-hash-tcp-ipv4-ex
set rss

set SelectMemoryRAS

To specify how the memory reliability, availability, and serviceability (RAS) is configured for the server, use the set SelectMemoryRAS command.

set SelectMemoryRAS { Lockstep | Maximum_Performance | Mirroring | Sparing }

Syntax Description

Lockstep	If the DIMM pairs in the server have an identical type, size, and organization and are populated across the SMI channels, you can enable lockstep mode to minimize memory access latency and provide better performance. This option offers better system performance than Mirroring and better reliability than Maximum Performance but lower reliability than Mirroring and lower system performance than Maximum Performance.
Maximum_Performance	System performance is optimized.
Mirroring	System reliability is optimized by using half the system memory as backup.
Sparing	The system reserves some memory for use in the event a DIMM fails. If that happens, the server takes the DIMM offline and replaces it with the reserved memory. This option provides less redundancy than mirroring, but it leaves more of the memory available for programs running on the server.

Command Default

System performance is optimized.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.
1.4(4)	This command was modified to add the Lockstep keyword.

Usage Guidelines

Note

This command is not available on all models and configurations. Some keywords are not supported on all models and configurations.

Examples

This example configures memory mirroring for system reliability and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set SelectMemoryRAS Mirroring
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set MirroringMode
set SparingMode

set send-alert (pef)

To enable performance event filter alerts on the server, use the set send-alert command in pef mode.

set send-alert { no | | yes }

Syntax Description

no	Specifies that performance event filter alerts are not enabled.
yes	Specifies that performance event filter alerts are enabled.

Command Default

None

Command Modes

Performance event filters (/fault/pef)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to enable performance event filter alerts on the server:

server# scope fault
server /fault # scope pef 3
server /fault/pef # set send-alert yes
server /fault/pef* # commit
server /fault/pef #

Related Commands

Command	Description
show pef

set Serial-PortA

To enable or disable serial port A, use the set Serial-PortA command.

set Serial-PortA { Disabled | Enabled }

Syntax Description

Disabled	The port is disabled.
Enabled	The port is enabled.

Command Default

The port is enabled.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Note

This command is not available on all models and configurations.

Examples

This example disables serial port A and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set Serial-PortA Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set SerialPortAAddress
show advanced

set SerialPortAAddress

To specify the address to be used by serial port A, use the set SerialPortAAddress command.

set SerialPortAAddress { 2E8 | 3E8 | 3F8 }

Syntax Description

2E8	The port uses address 2E8.
3E8	The port uses address 3E8.
3F8	The port uses address 3F8.

Command Default

The port uses address 3F8.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

By replacing the port letter A in the command with the letter B, you can modify this command to specify an address for serial port B. For example, to specify an address for serial port B, use the set SerialPortBAddress command.

Note

This command is not available on all models and configurations.

Examples

This example specifies that serial port A uses address 3E8 and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set SerialPortAAddress 3E8
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set Serial-PortA
show advanced

set Serial-PortB

To enable or disable serial port B, use the set Serial-PortB command.

set Serial-PortB { Disabled | Enabled }

Syntax Description

Disabled	The port is disabled.
Enabled	The port is enabled.

Command Default

The port is enabled.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Note

This command is not available on all models and configurations.

Examples

This example disables serial port B and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set Serial-PortB Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set SerialPortBAddress
show advanced

set SerialPortBAddress

To specify the address to be used by serial port B, use the set SerialPortBAddress command.

set SerialPortBAddress { 2E8 | 2F8 | 3E8 | 3F8 }

Syntax Description

2E8	The port uses address 2E8.
2F8	The port uses address 2F8.
3E8	The port uses address 3E8.
3F8	The port uses address 3F8.

Command Default

The port uses address 2F8.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Note

This command is not available on all models and configurations.

Examples

This example specifies that serial port B uses address 3E8 and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set SerialPortBAddress 3E8
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set Serial-PortB
show advanced

set server-1

To specify a Network Time Protocol (NTP) server that will act as a time source for CIMC, use the set server-1 command.

set server-1 IP address

Syntax Description

IP address

IP/DNS address of the time source for the server. The preferred value is the IP address of the server.

Command Default

None

Command Modes

NTP (/cimc/network/ntp)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must enable NTP to use this command.

You must be logged in as an admin to use this command.

Examples

This example shows how to specify the IP address of one of the four servers that act as NTP servers:

Server # scope cimc
Server /cimc # scope network
Server /cimc/network # scope ntp
Server /cimc/network/ntp # set enabled yes 
Warning: IPMI Set SEL Time Command will be 
disabled if NTP is enabled. 
Do you wish to continue? [y|N]  
y
Server /cimc/network/ntp* # commit
Server /cimc/network/ntp # set server-1 10.120.33.44
Server /cimc/network/ntp* # set server-2 10.120.34.45
Server /cimc/network/ntp* # set server-3 10.120.35.46
Server /cimc/network/ntp* # set server-4 10.120.36.48
Server /cimc/network/ntp* # commit
Server /cimc/network/ntp #

This example shows how to clear the IP address of an NTP server, when there are fewer than four NTP servers:

Server # scope cimc
Server /cimc # scope network
Server /cimc/network # scope ntp
Server /cimc/network/ntp # set enabled yes 
Warning: IPMI Set SEL Time Command will be 
disabled if NTP is enabled. 
Do you wish to continue? [y|N]  
y
Server /cimc/network/ntp* # commit
Server /cimc/network/ntp # set server-1 ""
Server /cimc/network/ntp* # commit
Server /cimc/network/ntp #

Related Commands

Command	Description
scope ntp
set enabled
show ntp

set server-2

To specify a second Network Time Protocol (NTP) server that will act as a time source for CIMC, use the set server-2 command.

set server-2 IP address

Syntax Description

IP address

IP/DNS address of the time source for the server. The preferred value is the IP address of the server.

Command Default

None

Command Modes

NTP (/cimc/network/ntp)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must enable NTP to use this command.

You must be logged in as an admin to use this command.

Examples

This example shows how to specify the IP address for a second server that acts as an NTP server:

Server # scope cimc
Server /cimc # scope network
Server /cimc/network # scope ntp
Server /cimc/network/ntp # set enabled yes 
Warning: IPMI Set SEL Time Command will be 
disabled if NTP is enabled. 
Do you wish to continue? [y|N]  
y
Server /cimc/network/ntp* # commit
Server /cimc/network/ntp # set server-1 10.120.33.44
Server /cimc/network/ntp* # set server-2 10.120.34.45
Server /cimc/network/ntp* # set server-3 10.120.35.46
Server /cimc/network/ntp* # set server-4 10.120.36.48
Server /cimc/network/ntp* # commit
Server /cimc/network/ntp #

This example shows how to clear the IP address of an NTP server, when there are fewer than four NTP servers:

Server # scope cimc
Server /cimc # scope network
Server /cimc/network # scope ntp
Server /cimc/network/ntp # set enabled yes 
Warning: IPMI Set SEL Time Command will be 
disabled if NTP is enabled. 
Do you wish to continue? [y|N]  
y
Server /cimc/network/ntp* # commit
Server /cimc/network/ntp # set server-2 ""
Server /cimc/network/ntp* # commit
Server /cimc/network/ntp #

Related Commands

Command	Description
scope ntp
set enabled
show ntp

set server-3

To specify a third Network Time Protocol (NTP) server that will act as a time source for CIMC, use the set server-3 command.

set server-3 IP address

Syntax Description

IP address

IP/DNS address of the time source for the server. The preferred value is the IP address of the server.

Command Default

None

Command Modes

NTP (/cimc/network/ntp)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must enable NTP to use this command.

You must be logged in as an admin to use this command.

Examples

This example shows how to specify the IP address of a third server that acts as an NTP server:

Server # scope cimc
Server /cimc # scope network
Server /cimc/network # scope ntp
Server /cimc/network/ntp # set enabled yes 
Warning: IPMI Set SEL Time Command will be 
disabled if NTP is enabled. 
Do you wish to continue? [y|N]  
y
Server /cimc/network/ntp* # commit
Server /cimc/network/ntp # set server-1 10.120.33.44
Server /cimc/network/ntp* # set server-2 10.120.34.45
Server /cimc/network/ntp* # set server-3 10.120.35.46
Server /cimc/network/ntp* # set server-4 10.120.36.48
Server /cimc/network/ntp* # commit
Server /cimc/network/ntp #

This example shows how to clear the IP address of an NTP server, when there are fewer than four NTP servers:

Server # scope cimc
Server /cimc # scope network
Server /cimc/network # scope ntp
Server /cimc/network/ntp # set enabled yes 
Warning: IPMI Set SEL Time Command will be 
disabled if NTP is enabled. 
Do you wish to continue? [y|N]  
y
Server /cimc/network/ntp* # commit
Server /cimc/network/ntp # set server-3 ""
Server /cimc/network/ntp* # commit
Server /cimc/network/ntp #

Related Commands

Command	Description
scope ntp
set enabled
show ntp

set server-4

To specify a fourth Network Time Protocol (NTP) server that will act as a time source for CIMC, use the set server-4 command.

set server-4 IP address

Syntax Description

IP address

IP/DNS address of the time source for the server. The preferred value is the IP address of the server.

Command Default

None

Command Modes

NTP (/cimc/network/ntp)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must enable NTP to use this command.

You must be logged in as an admin to use this command.

Examples

This example shows how to specify the IP address of a fourth server that acts as an NTP server:

Server # scope cimc
Server /cimc # scope network
Server /cimc/network # scope ntp
Server /cimc/network/ntp # set enabled yes 
Warning: IPMI Set SEL Time Command will be 
disabled if NTP is enabled. 
Do you wish to continue? [y|N]  
y
Server /cimc/network/ntp* # commit
Server /cimc/network/ntp # set server-1 10.120.33.44
Server /cimc/network/ntp* # set server-2 10.120.34.45
Server /cimc/network/ntp* # set server-3 10.120.35.46
Server /cimc/network/ntp* # set server-4 10.120.36.48
Server /cimc/network/ntp* # commit
Server /cimc/network/ntp #

This example shows how to clear the IP address of an NTP server, when there are fewer than four NTP servers:

Server # scope cimc
Server /cimc # scope network
Server /cimc/network # scope ntp
Server /cimc/network/ntp # set enabled yes 
Warning: IPMI Set SEL Time Command will be 
disabled if NTP is enabled. 
Do you wish to continue? [y|N]  
y
Server /cimc/network/ntp* # commit
Server /cimc/network/ntp # set server-4 ""
Server /cimc/network/ntp* # commit
Server /cimc/network/ntp #

Related Commands

Command	Description
scope ntp
set enabled
show ntp

set server-ip

To specify the IP address of a remote server, use the set server-ip command.

set server-ip ip-address

Syntax Description

ip-address

Specifies the IP address of a remote server.

Command Default

None

Command Modes

CIMC log server (/cimc/log/server)

Command History

Release	Modification
1.0(1)	This command was introduced.
1.1(2)	This command was added to the CIMC log server command mode.
1.4(1)	This command was removed from the LDAP command mode.

Usage Guidelines

Use this command to configure the IP address of a remote syslog server for sending CIMC log entries.

Examples

This example shows how to configure a remote syslog server profile and enable the sending of CIMC log entries:

Server# scope cimc
Server /cimc # scope log
Server /cimc/log # scope server 2
Server /cimc/log/server # set server-ip 192.0.2.34
Server /cimc/log/server *# set enabled yes
Server /cimc/log/server *# commit
Server /cimc/log/server #

Related Commands

Command	Description
show server

set Slot-n-ROM

To enable or disable a PCIe slot ROM, use the set Slot-n-ROM command.

set Slot-n-ROM { Disabled | Enabled }

Syntax Description

n	The number or letter of the PCIe slot.
Disabled	The PCIe slot ROM is disabled.
Enabled	The PCIe slot ROM is enabled.

Command Default

The PCIe slot ROM is enabled.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to enable or disable a Peripheral Component Interconnect Express (PCIe) slot ROM designated by n in the command name Slot-n-ROM.

Examples

This example disables the PCIe slot 2 ROM and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set Slot-2-ROM Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set Slot1Disable

To specify whether the PCIe expansion slot 1 is available to the server, use the set Slot1Disable command.

set Slot1Disable { Disabled | Enabled }

Syntax Description

Disabled	The expansion slot is not available.
Enabled	The expansion slot is available.

Command Default

The expansion slot is available.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

By replacing the numeral 1 in the command with the number of another PCIe expansion slot, you can modify this command to specify whether other expansion slots are available. For example, to configure expansion slot 2, use the set Slot2Disable command.

Examples

This example specifies that PCIe expansion slot 1 is not available and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set Slot1Disable Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set SlotMezzDisable
show advanced

set SlotMezzDisable

To specify whether the PCIe mezzanine slot expansion ROM is available to the server, use the set SlotMezzDisable command.

set SlotMezzDisable { Disabled | Enabled }

Syntax Description

Disabled	The mezzanine slot is not available.
Enabled	The mezzanine slot is available.

Command Default

The mezzanine slot is available.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example specifies that the PCIe mezzanine slot expansion ROM is not available and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set SlotMezzDisable Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set Slot1Disable
show advanced

set SparingMode

To specify how spared memory is allocated, use the set SparingMode command.

set SparingMode { Rank_Sparing | DIMM_Sparing }

Syntax Description

Rank_Sparing	Spared memory is allocated at the rank level.
DIMM_Sparing	Spared memory is allocated at the DIMM level.

Command Default

Spared memory is allocated at the rank level.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to specify how spared memory is allocated.

Note

This command is operative only if the set SelectMemoryRAS command is set to Sparing.

Examples

This example configures allocation of spared memory at the DIMM level and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set SelectMemoryRAS Sparing
Server /bios/advanced *# set SparingMode DIMM_Sparing
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set SelectMemoryRAS
show advanced

set ssh-port

To specify the port number for SSH connections to CIMC, use the set ssh-port command.

set ssh-port port-number

Syntax Description

port-number

The port number for SSH connections to CIMC.

Command Default

The default port number is 22.

Command Modes

Secure shell (/ssh)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example configures a port number of 22 for SSH connections:

server# scope ssh
server /ssh # set enabled yes
server /ssh* # set ssh-port 22
server /ssh* # commit
server /ssh #

Related Commands

Command	Description
show ssh

set sys-contact

To specify the SNMP system contact information, use the set sys-contact command.

set sys-contact contact

Syntax Description

contact

The SNMP contact information.

Command Default

None

Command Modes

SNMP (/snmp)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Use this command to specify the system contact person responsible for the SNMP implementation. The contact information can be up to 254 characters, such as an email address or a name and telephone number. To enter a value that contains spaces, you must enclose the entry with quotation marks.

SNMP must be enabled and saved before this command can be accepted.

Examples

This example configures the SNMP parameters and commits the transaction:

scope snmp
Server /snmp # set enabled yes
Server /snmp *# commit
Server /snmp # set community-str cimcpublic
Server /snmp *# set sys-contact "User Name <username@example.com> +1-408-555-1212"
Server /snmp *# set sys-location "San Jose, California"
Server /snmp *# commit
Server /snmp #  show detail
SNMP Settings:
    SNMP Port: 161
    System Contact: User Name <username@example.com> +1-408-555-1212
    System Location: San Jose, California
    SNMP Community: cimcpublic
    SNMP Trap community: 0
    Enabled: yes
    SNMP Trap Version: 1
    SNMP Inform Type: inform

Server /snmp #

Related Commands

Command	Description
scope snmp
show snmp

set sys-location

To specify the SNMP system server location, use the set sys-location command.

set sys-location location

Syntax Description

location

The SNMP system server location information.

Command Default

None

Command Modes

SNMP (/snmp)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Use this command to specify the location of the host on which the SNMP agent (server) runs. The location information can be up to 254 characters. To enter a value that contains spaces, you must enclose the entry with quotation marks.

SNMP must be enabled and saved before this command can be accepted.

Examples

This example configures the SNMP parameters and commits the transaction:

scope snmp
Server /snmp # set enabled yes
Server /snmp *# commit
Server /snmp # set community-str cimcpublic
Server /snmp *# set sys-contact "User Name <username@example.com> +1-408-555-1212"
Server /snmp *# set sys-location "San Jose, California"
Server /snmp *# commit
Server /snmp #  show detail
SNMP Settings:
    SNMP Port: 161
    System Contact: User Name <username@example.com> +1-408-555-1212
    System Location: San Jose, California
    SNMP Community: cimcpublic
    SNMP Trap community: 0
    Enabled: yes
    SNMP Trap Version: 1
    SNMP Inform Type: inform

Server /snmp #

Related Commands

Command	Description
scope snmp
show snmp

set tcp-large-receive-offload

To enable or disable the TCP Large Packet Receive Offload, use the set tcp-large-receive offload command.

settcp-large-receive-offload { disable | enable }

Syntax Description

disable	The CPU processes all large packets.
enable	The hardware reassembles all segmented packets before sending them to the CPU. This option may reduce CPU utilization and increase inbound throughput.

Command Default

The default is enable.

Command Modes

Offload (/chassis/adapter/host-eth-if/offload)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the TCP Large Packet Receive Offload:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0 
Server /chassis/adapter/host-eth-if # scope offload
Server /chassis/adapter/host-eth-if/offload # set tcp-large-receive-offload disable
Server /chassis/adapter/host-eth-if/offload *# commit
Committed host-eth-if eth0 settings will take effect upon the next server reset
Server /chassis/adapter/host-eth-if/offload #

Related Commands

Command	Description
set tcp-tx-checksum-offload

set tcp-rx-checksum-offload

To enable or disable the TCP receive checksum validation offload, use the set tcp-rx-checksum-offload command.

set tcp-rx-checksum-offload { disable | enable }

Syntax Description

disable	The CPU validates all packet checksums.
enable	The CPU sends all packet checksums to the hardware for validation. This option may reduce CPU overhead.

Command Default

The default is enable.

Command Modes

Offload (/chassis/adapter/host-eth-if/offload)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the TCP rx checksum offload:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # scope offload
Server /chassis/adapter/host-eth-if/offload # set tcp-rx-checksum-offload disable
Server /chassis/adapter/host-eth-if/offload *# commit
Committed host-eth-if eth0 settings will take effect upon the next server reset
Server /chassis/adapter/host-eth-if/offload #

Related Commands

Command	Description
set tcp-tx-checksum-offload
set tcp-segment-offload

set tcp-segment-offload

To enable or disable the TCP segment offload, use the set tcp-segment-offload command.

set tcp-segment-offload { disable | enable }

Syntax Description

disable	Disables the CPU segments large TCP packets.
enable	Enables the CPU to send large TCP packets to the hardware to be segmented.

Command Default

The default is enable.

Command Modes

Offload (/chassis/adapter/host-eth-if/offload)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the TCP segment offload:

Server# scope chassis 
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # scope offload
Server /chassis/adapter/host-eth-if/offload # set tcp-segment-offload disable
Server /chassis/adapter/host-eth-if/offload *# commit
Committed host-eth-if eth0 settings will take effect upon the next server reset
Server /chassis/adapter/host-eth-if/offload #

Related Commands

Command	Description
set tcp-tx-checksum-offload
set tcp-rx-checksum-offload

set tcp-tx-checksum-offload

To enable or disable the TCP Transmit Offload Checksum Validation, use the set tcp-tx-checksum-offload command.

set tcp-tx-checksum-offload { disable | | enable }

Syntax Description

disable	The CPU validates all packet checksums.
enable	The CPU sends all packet checksums to the hardware for validation. This option may reduce CPU overhead.

Command Default

The default is enable.

Command Modes

Offload (/chassis/adapter/host-eth-if/offload)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the TCP rx checksum offload:

Server# scope chassis 
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # scope offload
Server /chassis/adapter/host-eth-if/offload # set tcp-tx-checksum-offload disable
Server /chassis/adapter/host-eth-if/offload *# commit
Committed host-eth-if eth0 settings will take effect upon the next server reset
Server /chassis/adapter/host-eth-if/offload #

Related Commands

Command	Description
set tcp-tx-checksum-offload
set tcp-rx-checksum-offload

set TerminalType

To specify the type of character formatting for console redirection, use the set TerminalType command.

set TerminalType { PC-ANSI | VT100 | VT-100-PLUS | VT-UTF8 }

Syntax Description

PC-ANSI	The PC-ANSI terminal font is used.
VT-UTF8	A video terminal with the UTF-8 character set is used.
VT100	A supported vt100 video terminal and its character set are used.
VT-100-PLUS	A supported vt100-plus video terminal and its character set are used.

Command Default

A supported vt100 video terminal and its character set are used.

Command Modes

Server Management BIOS (/bios/server-management)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Use this command to specify the type of character formatting for console redirection.

Note

This setting must match the setting on the remote terminal application.

Examples

This example specifies a video terminal with the UTF-8 character set and commits the transaction:

Server# scope bios
Server /bios # scope server-management
Server /bios/server-management # set TerminalType VT-UTF8
Server /bios/server-management *# commit
Server /bios/server-management #

Related Commands

Command	Description
show server-management

set tftp-ip (tech-support)

To set the TFTP server IP address, use the set tftp-ip command in tech-support mode.

set tftp-ip ip-address

Syntax Description

ip-address

The IP address of the TFTP server. The format is X.X.X.X.

Command Default

None

Command Modes

Technical support (/cimc/tech-support)

Command History

Release	Modification
1.0(1)	This command was introduced.
1.5(1)	This command is replaced with the set remote-ip command.

Usage Guidelines

Specifies the IP address of the TFTP server on which the support data file should be stored.

Perform this task along with set path when requested by the Cisco Technical Assistance Center (TAC). This utility creates a summary report containing configuration information, logs and diagnostic data that will help TAC in troubleshooting and resolving technical issues.

Examples

This example shows how to set the TFTP server IP address:

server# scope cimc
server /cimc # scope tech-support
server /cimc/tech-support # set tftp-ip 209.165.200.225
server /cimc/tech-support* # commit
server /cimc/tech-support #

Related Commands

Command	Description
set tftp-path
show tech-support

set timeout

To specify a timeout period, use the set timeout command.

set timeout time

Syntax Description

time	The timeout period, in seconds.

Command Default

The default HTTP timeout is 1800 seconds.

The default LDAP timeout is 60 seconds.

The default SSH timeout is 1800 seconds.

Command Modes

HTTP (/http)

LDAP (/ldap)

Secure shell (/ssh)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

In the HTTP and SSH scopes, use this command to specify the connection timeout period in seconds.

In the LDAP scope, use this command to specify the period in seconds until the LDAP search operation times out.

For different types of connections, the timeout period ranges and defaults are as follows:

HTTP — The range is 60 to 10800; the default is 1800.
LDAP — The range is 0 to 1800; the default is 60.
SSH — The range is 60 to 10800; the default is 1800.

Examples

This example shows how to set the HTTP connection timeout to 600 seconds:

server# scope http
server /http # set timeout 600
server /http* # commit
server /http #

Related Commands

Command	Description
show http
show ldap
show ssh

set TPMAdminCtrl

To specify whether the server uses the Trusted Platform Module (TPM) to ensure all data is securely encrypted, use the set TPMAdminCtrl command.

set TPMAdminCtrl { Disabled | Enabled }

Syntax Description

Disabled	The server does not use the TPM for data encryption.
Enabled	Data encryption is handled by the TPM.

Command Default

The server does not use the TPM for data encryption.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(3)	This command was introduced.

Examples

This example specifies that the server uses the TPM to ensure all data is securely encrypted and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set TPMAdminCtrl Enable
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
show advanced

set trap-community-str

To specify the SNMP community to which trap information should be sent, use the set trap-community-str command.

set trap-community-str trap-community

Syntax Description

trap-community

The SNMP v1 or v2c community name or SNMP v3 username.

Command Default

None

Command Modes

SNMP (/snmp)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to specify the SNMP community to which trap information should be sent.

SNMP must be enabled and saved before this command can be accepted.

Examples

This example configures the SNMP parameters and commits the transaction:

scope snmp
Server /snmp # set enabled yes
Server /snmp *# commit
Server /snmp # set trap-community-str public-trap
Server /snmp *# commit
Server /snmp #  show detail
SNMP Settings:
    SNMP Port: 161
    System Contact: 
    System Location: 
    SNMP Community: 
    SNMP Trap community: public-trap
    Enabled: yes
    SNMP Trap Version: 1
    SNMP Inform Type: inform

Server /snmp #

Related Commands

Command	Description
show snmp

set trap-ver

To specify the SNMP version of trap messages, use the set trap-ver command.

set trap-ver { 1 | 2 | 3 }

Syntax Description

1 | 2 | 3

The SNMP version number of trap messages.

Command Default

Trap messages are of type SNMPv1.

Command Modes

SNMP (/snmp)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to specify the SNMP version number for trap messages. Valid values are 1, 2, or 3 for SNMP v1, v2c, or v3.

Note

SNMPv3 traps will be delivered only to locations where the SNMPv3 user and key values are configured correctly.

SNMP must be enabled and saved before this command can be accepted.

Examples

This example specifies SNMPv3 trap messages and commits the transaction:

scope snmp
Server /snmp # set enabled yes
Server /snmp *# commit
Server /snmp # set trap-ver 3
Server /snmp *# commit
Server /snmp #  show detail
SNMP Settings:
    SNMP Port: 161
    System Contact: User Name <username@example.com> +1-408-555-1212
    System Location: San Jose, California
    SNMP Community: cimcpublic
    SNMP Trap community: 0
    Enabled: yes
    SNMP Trap Version: 3
    SNMP Inform Type: inform

Server /snmp #

Related Commands

Command	Description
scope trap-destination

set trust-host-cos

To specify whether the vNIC will trust host CoS or will remark packets, use the set trust-host-cos command.

set trust-host-cos { disable | enable }

Syntax Description

disable	Received packets are remarked with the configured CoS value.
enable	The existing CoS value of received packets is preserved.

Command Default

Received packets are remarked.

Command Modes

Ethernet host interface (/chassis/adapter/host-eth-if)

Command History

Release	Modification
1.2(1)	This command was introduced.

Usage Guidelines

Use this command to specify whether the vNIC will trust host CoS or will remark packets. By default, the received host CoS is not trusted, and the vNIC will remark the packets with the CoS value configured by the set cos command or with a value of zero (0) if no CoS value is configured. If this command is enabled, the vNIC will preserve the CoS value of received packets.

Examples

This example shows how to specify that received CoS values are preserved (trusted) by Ethernet host interface eth0:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # set trust-host-cos enable
Server /chassis/adapter/host-eth-if *# commit
Server /chassis/adapter/host-eth-if #

Related Commands

Command	Description
set cos

set uplink

To specify the uplink port associated with a vNIC, use the set uplink command.

set uplink { 0 | 1 }

Syntax Description

0	All traffic for this vNIC goes through uplink port 0.
1	All traffic for this vNIC goes through uplink port 1.

Command Default

None

Command Modes

Ethernet host interface (/chassis/adapter/host-eth-if)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to associate uplink port 1 with the Ethernet host interface eth0:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # set uplink 1
Server /chassis/adapter/host-eth-if *# commit
Server /chassis/adapter/host-eth-if #

Related Commands

Command	Description
show host-eth-if

set uplink-failback-timeout

To specify the NIV uplink failback timeout for the host interface, use the set uplink-failback-timeout command.

set uplink-failback-timeout seconds

Syntax Description

seconds

Specifies the timeout in seconds. The range is 0 to 600.

Command Default

None

Command Modes

Ethernet host interface (/chassis/adapter/host-eth-if)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

After a vNIC has started using its secondary interface, this setting controls how long the primary interface must be available before the system resumes using the primary interface for the vNIC.

Note

To use this command, you must enable NIV mode for the adapter.

Examples

This example shows how to specify an NIV uplink failback timeout of 60 seconds on interface eth0 on adapter card 1:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # set niv-mode enabled
Server /chassis/adapter *# scope host-eth-if eth0
Server /chassis/adapter/host-eth-if *# set uplink-failover enabled
Server /chassis/adapter/host-eth-if *# set uplink-failback-timeout 60
Server /chassis/adapter/host-eth-if *# commit
Server /chassis/adapter/host-eth-if #

Related Commands

Command	Description
set niv-mode
set uplink-failover

set uplink-failover

To allow the vNIC to fail over to the secondary interface, use the set uplink-failover command.

set uplink-failover { disabled | enabled }

Syntax Description

disabled	Disables failover.
enabled	Allows failover.

Command Default

None

Command Modes

Ethernet host interface (/chassis/adapter/host-eth-if)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Enable this setting if traffic on this vNIC should fail over to the secondary interface if there are communication problems.

Note

To use this command, you must enable NIV mode for the adapter.

Examples

This example shows how to enable uplink failover on interface eth0 on adapter card 1:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # set niv-mode enabled
Server /chassis/adapter *# scope host-eth-if eth0
Server /chassis/adapter/host-eth-if *# set uplink-failover enabled
Server /chassis/adapter/host-eth-if *# set uplink-failback-timeout 60
Server /chassis/adapter/host-eth-if *# commit
Server /chassis/adapter/host-eth-if #

Related Commands

Command	Description
set niv-mode
set uplink-failback-timeout

set USBController

To specify whether the server uses its built-in USB controller, use the set USBController command.

set USBController { Disabled | Enabled }

Syntax Description

Disabled	The server does not use its built-in USB controller.
Enabled	The server uses its built-in USB controller.

Command Default

The server uses its built-in USB controller.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example disables the built-in USB controller and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set USBController Disabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set MakeUSBDeviceNonBootable
show advanced

set UsbEmul6064

To specify whether the system supports 60h/64h emulation for complete USB keyboard legacy support, use the set UsbEmul6064 command.

set UsbEmul6064 { Disabled | Enabled }

Syntax Description

Disabled	60h/64 emulation is not supported.
Enabled	60h/64 emulation is supported.

Command Default

60h/64 emulation is supported.

Command Modes

Advanced BIOS (/bios/advanced)

Command History

Release	Modification
1.4(4)	This command was introduced.

Usage Guidelines

Use this command to specify whether the system supports 60h/64h emulation for complete USB keyboard legacy support. You should select this option if you are using a non-USB aware operating system on the server.

Examples

This example enables 60h/64 emulation and commits the transaction:

Server# scope bios
Server /bios # scope advanced
Server /bios/advanced # set UsbEmul6064 Enabled
Server /bios/advanced *# commit
Server /bios/advanced #

Related Commands

Command	Description
set LegacyUSBSupport

set v3add

To add or modify an SNMPv3 user, use the set v3add command.

set v3add { yes | no }

Syntax Description

yes	This user is enabled as an SNMPv3 user and is allowed to access the SNMP OID tree.
no	This user configuration is deleted.

Command Default

None

Command Modes

SNMPv3 users (/snmp/v3users)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to add or delete the configuration for an SNMPv3 user. You can configure up to 15 users.

Note

When you add a user configuration, you must also configure the security name and security level at the same time or the user addition will fail.

Examples

This example adds and then deletes SNMPv3 user number 2:

Server# scope snmp
Server /snmp # scope v3users 2
Server /snmp/v3users # set v3add yes
Server /snmp/v3users *# set v3security-name ucsSNMPV3user
Server /snmp/v3users *# set v3security-level noauthnopriv
Server /snmp/v3users *# commit
Settings are being applied ... allow a few minutes for the process to complete
Server /snmp/v3users # show detail
User 2:
    Add User: yes
    Security Name: ucsSNMPV3user
    Security Level: noauthnopriv
    Auth Type: (N/A)
    Auth Key: ******
    Encryption: (N/A)
    Private Key: ******

Server /snmp/v3users # set v3add no
Warning: Are you sure you want to delete the user? If not, use "discard" to cancel this 
operation
Server /snmp/v3users *# commit
All parameters discarded and user disabled.

Server /snmp/v3users #

Related Commands

Command	Description
set v3security-level
set v3security-name

set v3auth-key

To specify an authorization key for an SNMPv3 user, use the set v3auth-key command.

set v3auth-key

This command has no arguments or keywords.

Command Default

None

Command Modes

SNMPv3 users (/snmp/v3users)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to specify an authorization key for an SNMPv3 user. When you enter the command, you are prompted to type an authorization key twice.

Examples

This example specifies an authorization key for SNMPv3 user number 2:

Server# scope snmp
Server /snmp # scope v3users 2
Server /snmp/v3users # set v3add yes
Server /snmp/v3users *# set v3security-name ucsSNMPV3user
Server /snmp/v3users *# set v3security-level authnopriv
Server /snmp/v3users *# set v3proto SHA
Server /snmp/v3users *# set v3auth-key
Please enter v3auth-key:ex4mp1ek3y
Please confirm v3auth-key:ex4mp1ek3y
Server /snmp/v3users *# commit
Settings are being applied ... allow a few minutes for the process to complete
Server /snmp/v3users #

Related Commands

Command	Description
set v3proto

set v3priv-auth-key

To specify a private encryption key for an SNMPv3 user, use the set v3priv-auth-key command.

set v3priv-auth-key

This command has no arguments or keywords.

Command Default

None

Command Modes

SNMPv3 users (/snmp/v3users)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to specify a private encryption key (privacy password) for an SNMPv3 user. When you enter the command, you are prompted to type an encryption key twice.

Examples

This example specifies an encryption key for SNMPv3 user number 2:

Server# scope snmp
Server /snmp # scope v3users 2
Server /snmp/v3users # set v3add yes
Server /snmp/v3users *# set v3security-name ucsSNMPV3user
Server /snmp/v3users *# set v3security-level authpriv
Server /snmp/v3users *# set v3proto SHA
Server /snmp/v3users *# set v3auth-key
Please enter v3auth-key:ex4mp1ek3y
Please confirm v3auth-key:ex4mp1ek3y
Server /snmp/v3users *# set v3priv-proto AES
Server /snmp/v3users *# set v3priv-auth-key 
Please enter v3priv-auth-key:!1@2#3$4%5^6&7*8
Please confirm v3priv-auth-key:!1@2#3$4%5^6&7*8
Server /snmp/v3users *# commit
Settings are being applied ... allow a few minutes for the process to complete
Server /snmp/v3users #

Related Commands

Command	Description
set v3priv-proto

set v3priv-proto

To specify the data encryption protocol for an SNMPv3 user, use the set v3priv-proto command.

set v3priv-proto { DES | AES }

Syntax Description

DES	Specifies encryption using the Data Encryption Standard (DES) protocol.
AES	Specifies encryption using the Advanced Encryption Standard (AES) protocol.

Command Default

None

Command Modes

SNMPv3 users (/snmp/v3users)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to specify the data encryption protocol for an SNMPv3 user. AES is more secure than DES but requires more computation power and may not be supported in older systems.

Examples

This example specifies AES encryption for SNMPv3 user number 2:

Server# scope snmp
Server /snmp # scope v3users 2
Server /snmp/v3users # set v3add yes
Server /snmp/v3users *# set v3security-name ucsSNMPV3user
Server /snmp/v3users *# set v3security-level authpriv
Server /snmp/v3users *# set v3proto SHA
Server /snmp/v3users *# set v3auth-key
Please enter v3auth-key:ex4mp1ek3y
Please confirm v3auth-key:ex4mp1ek3y
Server /snmp/v3users *# set v3priv-proto AES
Server /snmp/v3users *# set v3priv-auth-key 
Please enter v3priv-auth-key:!1@2#3$4%5^6&7*8
Please confirm v3priv-auth-key:!1@2#3$4%5^6&7*8
Server /snmp/v3users *# commit
Settings are being applied ... allow a few minutes for the process to complete
Server /snmp/v3users #

Related Commands

Command	Description
set v3priv-auth-key

set v3proto

To specify the authentication protocol for an SNMPv3 user, use the set v3proto command.

set v3proto { MD5 | SHA }

Syntax Description

MD5	Specifies authentication using the Message Digest 5 (MD5) protocol.
SHA	Specifies encryption using the Secure Hash Algorithm (SHA) protocol.

Command Default

None

Command Modes

SNMPv3 users (/snmp/v3users)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to specify the authentication protocol for an SNMPv3 user. SHA is more secure but requires more computation power and may not be supported in older systems.

Examples

This example specifies SHA authentication for SNMPv3 user number 2:

Server# scope snmp
Server /snmp # scope v3users 2
Server /snmp/v3users # set v3add yes
Server /snmp/v3users *# set v3security-name ucsSNMPV3user
Server /snmp/v3users *# set v3security-level authnopriv
Server /snmp/v3users *# set v3proto SHA
Server /snmp/v3users *# set v3auth-key 
Please enter v3auth-key:ex4mp1ek3y
Please confirm v3auth-key:ex4mp1ek3y
Server /snmp/v3users *# commit
Settings are being applied ... allow a few minutes for the process to complete
Server /snmp/v3users #

Related Commands

Command	Description
set v3auth-key

set v3security-level

To specify the security level for an SNMPv3 user, use the set v3security-level command.

set v3security-level { noauthnopriv | authnopriv | authpriv }

Syntax Description

noauthnopriv	The user does not require an authorization or privacy password.
authnopriv	The user requires an authorization password but not a privacy password.
authpriv	The user requires both an authorization password and a privacy password.

Command Default

None

Command Modes

SNMPv3 users (/snmp/v3users)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to specify the security level for an SNMPv3 user. If authentication is required, you must configure an authentication protocol and key. If privacy (encryption) is required, you must configure a private encryption protocol and key (privacy password).

Examples

This example specifies authentication but no privacy for SNMPv3 user number 2:

Server# scope snmp
Server /snmp # scope v3users 2
Server /snmp/v3users # set v3add yes
Server /snmp/v3users *# set v3security-name ucsSNMPV3user
Server /snmp/v3users *# set v3security-level authnopriv
Server /snmp/v3users *# set v3proto SHA
Server /snmp/v3users *# set v3auth-key 
Please enter v3auth-key:ex4mp1ek3y
Please confirm v3auth-key:ex4mp1ek3y
Server /snmp/v3users *# commit
Settings are being applied ... allow a few minutes for the process to complete
Server /snmp/v3users #

Related Commands

Command	Description
set v3auth-key
set v3proto
set v3priv-auth-key
set v3priv-proto

set v3security-name

To specify a security name for an SNMPv3 user, use the set v3security-name command.

set v3security-name security-name

Syntax Description

security-name

The security name for the SNMPv3 user.

Command Default

None

Command Modes

SNMPv3 users (/snmp/v3users)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to specify the security name for an SNMPv3 user.

Examples

This example specifies a the security name for SNMPv3 user number 2:

Server# scope snmp
Server /snmp # scope v3users 2
Server /snmp/v3users # set v3add yes
Server /snmp/v3users *# set v3security-name ucsSNMPV3user
Server /snmp/v3users *# set v3security-level noauthnopriv
Server /snmp/v3users *# commit
Settings are being applied ... allow a few minutes for the process to complete
Server /snmp/v3users #

Related Commands

Command	Description
set v3security-level

set v4-addr

To specify the IPv4 address of the server, use the set v4-addr command.

set v4-addr ip-address

Syntax Description

ip-address

An IPv4 address in the format X.X.X.X.

Command Default

None

Command Modes

Network (/cimc/network)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example sets the IPv4 address of the server:

server# scope cimc
server /cimc # scope network
server /cimc/network # set v4-addr 192.0.20.111
server /cimc/network* # commit
server /cimc/network #

Related Commands

Command	Description
show network

set v4-gateway

To specify the IPv4 address of the local gateway, use the set v4-gateway command.

set v4-gateway ip-address

Syntax Description

ip-address

An IPv4 address in the format X.X.X.X.

Command Default

None

Command Modes

Network (/cimc/network)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example specifies the IPv4 address of the gateway:

server# scope cimc
server /cimc # scope network
server /cimc/network # set v4-gateway 192.0.20.254
server /cimc/network* # commit
server /cimc/network #

Related Commands

Command	Description
show network

set v4-netmask

To specify the IPv4 netmask of the server, use the set v4-netmask command.

set v4-netmask ip-address

Syntax Description

ip-address

An IPv4 netmask in the format X.X.X.X.

Command Default

None

Command Modes

Network (/cimc/network)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example specifies the IPv4 netmask of the server:

server# scope cimc
server /cimc # scope network
server /cimc/network # set v4-netmask 255.255.240.0
server /cimc/network* # commit
server /cimc/network #

Related Commands

Command	Description
show network

set virtual-drives-enabled

To specify the virtual drives to be made available to the server, use the set virtual-drives-enabled command.

set virtual-drives-enabled drive-list

Syntax Description

drive-list

A list of virtual drives. See the Usage Guidelines for options and format.

Command Default

None

Command Modes

FlexFlash operational profile (/chassis/flexflash/operational-profile)

Command History

Release	Modification
1.3(3)	This command was introduced.

Usage Guidelines

Use this command to specify the virtual drives to be made available to the server as a USB-style drive. List each virtual drive you want the server to access. The options are as follows:

SCU—The server can access the Cisco UCS Server Configuration Utility.
DRIVERS—The server can access the Cisco drivers volume.
HV—The server can access the user-installed hypervisor.
HUU—The server can access the Cisco Host Upgrade Utility.

When listing more than one option, you must enclose the list in quotation marks (").

Examples

This example shows how to specify the virtual drives to be made available to the server for the first flash device:

Server# scope chassis
Server /chassis # scope flexflash FlexFlash-0
Server /chassis/flexflash # scope operational-profile
Server /chassis/flexflash/operational-profile # set virtual-drives-enabled "SCU DRIVERS"
Server /chassis/flexflash/operational-profile *# commit
Server /chassis/flexflash/operational-profile #

Related Commands

Command	Description
scope operational-profile

set vlan

To specify the assigned VLAN for an interface, use the set vlan command.

set vlan { none | vlan-id }

Syntax Description

none	The interface belongs to no VLAN. This is the default.
vlan-id	The interface belongs to the specified VLAN. Valid VLAN identifiers are 1 to 4094.

Command Default

The interface belongs to no VLAN.

Command Modes

Ethernet host interface (/chassis/adapter/host-eth-if)

Fibre Channel host interface (/chassis/adapter/host-fc-if)

Command History

Release	Modification
1.2(1)	This command was introduced.

Usage Guidelines

In an FCoE application, use this command to associate the vHBA with the FCoE VLAN.

Examples

This example shows how to assign the Fibre Channel host interface fc0 to VLAN 5:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # set vlan 5
Server /chassis/adapter/host-fc-if *# commit
Server /chassis/adapter/host-fc-if #

Related Commands

Command	Description

set vlan-enabled

To enable or disable VLAN membership for the server, use the set vlan-enabled command.

set vlan-enabled { no | yes }

Syntax Description

no	VLAN membership is disabled.
yes	VLAN membership is enabled.

Command Default

VLAN membership is disabled.

Command Modes

Network (/cimc/network)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example configures a VLAN connection for the CIMC to VLAN 200:

server# scope cimc
server /cimc # scope network
server /cimc/network # set vlan-enabled yes
server /cimc/network* # set vlan-id 200
server /cimc/network* # commit
server /cimc/network #

Related Commands

Command	Description
set vlan-id
show network

set vlan-id

To specify the VLAN number for connection to the server, use the set vlan-id command.

set vlan-id id

Syntax Description

id	The VLAN number.

Command Default

None

Command Modes

Network (/cimc/network)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example configures a VLAN connection for the CIMC to VLAN 200:

server# scope cimc
server /cimc # scope network
server /cimc/network # set vlan-enabled yes
server /cimc/network* # set vlan-id 200
server /cimc/network* # commit
server /cimc/network #

Related Commands

Command	Description
set vlan-enabled
show network

set vlan-mode

To specify the VLAN mode for a vNIC, use the set vlan-mode command.

set vlan-mode { access | trunk }

Syntax Description

access	The vNIC belongs to only one VLAN.
trunk	The vNIC can belong to more than one VLAN.

Command Default

The vNIC can belong to more than one VLAN.

Command Modes

Ethernet host interface (/chassis/adapter/host-eth-if)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to specify trunk VLAN mode for the Ethernet host interface eth0:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # set vlan-mode trunk
Server /chassis/adapter/host-eth-if *# commit
Server /chassis/adapter/host-eth-if #

Related Commands

Command	Description

set vlan-priority

To specify the VLAN priority, use the set vlan-priority command.

set vlan-priority priority

Syntax Description

priority

The VLAN priority. The range is 0 to 7.

Command Default

The default VLAN priority is 0.

Command Modes

Network (/cimc/network)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example configures a VLAN connection with a priority of 5:

server# scope cimc
server /cimc # scope network
server /cimc/network # set vlan-enabled yes
server /cimc/network* # set vlan-id 200
server /cimc/network* # set vlan-priority 5
server /cimc/network* # commit
server /cimc/network #

Related Commands

Command	Description
set vlan-enabled
show network

set wq-count

To set the transmit queue count of the host Ethernet interface, use the set wq-count command.

set wq-count count

Syntax Description

count

The number of transmit queue resources to allocate. The range is 1 to 256.

Command Default

The default is 1.

Command Modes

Transmit queue (/chassis/adapter/host-eth-if/trans-queue)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the number of transmit queue resources to allocate:

Server# scope chassis
Server /chassis/ # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0 
Server /chassis/adapter/host-eth-if # scope trans-queue
Server /chassis/adapter/host-eth-if/trans-queue # set wq-count 3
Server /chassis/adapter/host-eth-if/trans-queue *# commit
Committed host-eth-if eth0 settings will take effect upon the next server reset
Server /chassis/adapter/host-eth-if/trans-queue #

Related Commands

Command	Description
set wq-ring-size

set wq-ring-size

To set the transmit queue ring size, use the set wq-ring-size command.

set wq-ring-size size

Syntax Description

size	The number of descriptors in the transmit queue. The range is 64 to 4094; the default is 256.

Command Default

The default is 256.

Command Modes

Transmit queue (/chassis/adapter/host-eth-if/trans-queue)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to set the number of descriptors in the transmit queue:

Server# scope chassis
Server /chassis/ # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # scope trans-queue
Server /chassis/adapter/host-eth-if/trans-queue # set wq-ring-size 68
Server /chassis/adapter/host-eth-if/trans-queue *# commit
Committed host-eth-if eth0 settings will take effect upon the next server reset
Server /chassis/adapter/host-eth-if/trans-queue #

Related Commands

Command	Description
set rq-count

set write-error-count-threshold

To specify the number of write errors that can occur before CIMC decides that the Cisco Flexible Flash card has failed, use the set write-error-count-threshold command.

set write-error-count-threshold value

Syntax Description

value

Number between 0 and 255. The value indicates the number of write errors that can occur before CIMC decides that the Cisco Flexible Flash card has failed.

Command Default

None

Command Modes

FlexFlash Operational Profile (/chassis/flexflash/operational-profile)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

Use this command to specify the number of write errors that can occur before CIMC decides that the Cisco Flexible Flash card has failed. Once this threshold has been reached, you must reset the Cisco Flexible Flash card before CIMC attempts to access it again.

Enter an integer between 1 and 255, or enter 0 (zero) if you want CIMC to continue using the card no matter how many errors it encounters.

Examples

This example shows how to set the write error threshold count to 100 for the Cisco Flexible Flash card:

Server # scope chassis
Server /chassis # scope flexflash FlexFlash-0
Server /chassis/flexflash # scope operational-profile
Server /chassis/flexflash/operational-profile # set write-error-count-threshold 100
Server /chassis/flexflash/operational-profile* # commit
Server /chassis/flexflash/operational-profile #

Related Commands

Command	Description
set raid-primary-member
set raid-secondary-role
set read-error-count-threshold
set virtual-drives-enabled

set wwnn

To specify the WWNN for an interface, use the set wwnn command.

set wwnn wwnn

Syntax Description

wwnn	Specifies a unique World Wide Node Name (WWNN) for the adapter in the form hh:hh:hh:hh:hh:hh:hh:hh.

Command Default

None

Command Modes

Fibre Channel host interface (/chassis/adapter/host-fc-if)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to assign a WWNN to the Fibre Channel host interface fc0:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # set wwnn 01:23:45:67:89:ab:cd:ef
Server /chassis/adapter/host-fc-if *# commit
Server /chassis/adapter/host-fc-if #

Related Commands

Command	Description
set wwpn

set wwpn

To specify the WWPN for an interface, use the set wwpn command.

set wwpn wwpn

Syntax Description

wwpn	Specifies a unique World Wide Port Name (WWPN) for the adapter in the form hh:hh:hh:hh:hh:hh:hh:hh.

Command Default

None

Command Modes

Fibre Channel host interface (/chassis/adapter/host-fc-if)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to assign a WWPN to the Fibre Channel host interface fc0:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # set wwpn 01:23:45:67:89:ab:cd:ef
Server /chassis/adapter/host-fc-if *# commit
Server /chassis/adapter/host-fc-if #

Related Commands

Command	Description
set wwnn

show (firmware)

To show whether basic server component firmware needs to be updated, use the show command.

Caution

This command should only be used under the direction of Cisco TAC.

show

Command Default

None

Command Modes

Firmware (/chassis/firmware)

Command History

Release	Modification
1.4(5)	This command was introduced.

Examples

This example shows how to update server firmware:

server# scope chassis
server /chassis # scope firmware
server /chassis/firmware # show
 Firmware update not required, all components are up to date

Related Commands

Command	Description
update-all

show actual-boot-order (bios)

To display the actual boot order, use the show actual-boot-order command in bios mode.

show actual-boot-order [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the actual boot order in list format.

Command Default

None

Command Modes

BIOS (/bios)

Command History

Release	Modification
1.0(1x)	This command was introduced.

Examples

This example shows how to display the actual boot order:

server# scope bios
server /bios # show actual-boot-order

Boot Order   Type                      Boot Device                         
------------ ------------------------- ----------------------------------- 
1            CD/DVD                    CD-ROM                              
2            CD/DVD                    Cisco   Virtual CD/DVD  1.18        
3            Network Device (PXE)      Cisco NIC 23:0.0                    
4            Network Device (PXE)      MBA v5.0.5  Slot 0100               
5            Network Device (PXE)      MBA v5.0.5  Slot 0101               
6            Network Device (PXE)      MBA v5.0.5  Slot 0200               
7            Network Device (PXE)      MBA v5.0.5  Slot 0201               
8            Network Device (PXE)      Cisco NIC 22:0.0                    
9            Internal EFI Shell        Internal EFI Shell                  
10           FDD                       Cisco   Virtual HDD     1.18        
11           FDD                       Cisco   Virtual Floppy  1.18
        
server /bios #

Related Commands

Command	Description
set boot-order

show adapter

To show the adapter properties, use the show adapter command.

show adapter index [detail]

Syntax Description

index	The PCI slot number of the adapter card.
detail	(Optional) Displays detailed adapter properties in list form.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to display information about the adapter:

Server# scope chassis
Server /chassis # show adapter 1
PCI Slot Product Name   Serial Number  Product ID     Vendor               
-------- -------------- -------------- -------------- -------------------- 
1        UCS VIC P81E   QCI1421A6SI    N2XX-ACPCI01   Cisco Systems Inc    
2        UCS VIC P81E   QCI1409A1RY    N2XX-ACPCI01   Cisco Systems Inc    

Server /chassis # show adapter 1 detail
PCI Slot 1:
    Product Name: UCS VIC P81E
    Serial Number: QCI1421A6SI
    Product ID: N2XX-ACPCI01
    Adapter Hardware Revision: 4
    Current FW Version: 1.6(0.11)
    NIV: Enabled
    FIP: Enabled
    Configuration Pending: no
    CIMC Management Enabled : no
    VID: V00
    Vendor: Cisco Systems Inc
    Description: LA-s4a
    FW Image 1 Version: 1.6(0.11)
    FW Image 1 State: RUNNING ACTIVATED
    FW Image 2 Version: 1.3(1.114)
    FW Image 2 State: BACKUP INACTIVATED
    FW Update Status: Idle
    FW Update Error: No error
    FW Update Stage: No operation (0%)
    FW Update Overall Progress: 0%

Server /chassis #

Related Commands

Command	Description
activate-adapter-fw
update-adapter-fw

show advanced

To display the advanced BIOS configuration settings, use the show advanced command.

show advanced [detail]

Syntax Description

detail

(Optional) Displays detailed advanced BIOS configuration settings in list format.

Command Default

None

Command Modes

BIOS (/bios)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example displays the advanced BIOS configuration details:

Server# scope bios
Server /bios # show advanced detail
Set-up parameters:
    Intel(R) VT-d Address Translati: Enabled
    Adjacent Cache Line prefetch: Enabled
    CPU Performance: Enterprise
    Intel(R) VT-d Coherency Support: Disabled
    Number of enabled cores: All
    Direct Cache Access: Enabled
    Enhanced Intel Speedstep(R) Tec: Enabled
    Execute Disable: Enabled
    Hardware Prefetcher: Enabled
    Intel(R) Hyper-Threading Techno: Enabled
    Intel(R) Turbo Boost Technology: Enabled
    Intel(R) Virtualization Technol: Enabled
    Intel(R) VT for Directed IO: Enabled
    Intel(R) VT-d Interrupt Remappi: Enabled
    Low Voltage DDR Mode: Power Saving Mode
    Make Device Non Bootable: Disabled
    Memory Mapped I/O above 4GB: Disabled
    NUMA Optimized: Enabled
    Onboard Gbit NIC 1: Enabled
    Onboard Gbit NIC 1 ROM: Enabled
    Onboard Gbit NIC 2: Enabled
    Onboard Gbit NIC 2 ROM: Enabled
    Intel(R) VT-d PassThrough DMA: Enabled
    PCIe OptionROMs: Enabled
    Processor C3 Report: Disabled
    Processor C6 Report: Enabled
    Select Memory RAS: Maximum Performance
    Serial A Enable: Enabled
    Serial A Address: 3F8h
    PCIe Slot A ROM: No
    PCIe Slot B ROM: No
    PCIe Slot C ROM: No
    PCIe Slot D ROM: No
    PCIe Slot E ROM: Enabled
    USB Controller: Enabled

Server /bios #

Related Commands

Command	Description
scope advanced

show bbu

To display battery backup information for a storage adapter, use the show bbu command.

show bbu [detail]

Syntax Description

detail

(Optional) Displays detailed information in list format.

Command Default

None

Command Modes

Storage adapter (/chassis/storageadapter)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example shows how to display battery backup information for a storage adapter in the SAS PCI slot:

server# scope chassis
server /chassis # scope storageadapter SAS
server /chassis/storageadapter # show bbu
Controller Battery Type Battery Present Voltage    Current    Charge Charging State 
---------- ------------ --------------- ---------- ---------- ------ -------------- 
SAS        iBBU         true            4.021 V    0.000 A    100%   fully charged  

server /chassis/storageadapter #

Related Commands

Command	Description
show storageadapter

show bios

To display information about the BIOS, use the show bios command.

show bios [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the bios, in list format.

Command Default

None

Command Modes

Root (server#)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

show bios displays the server boot order. show bios detail and show detail in bios mode displays the server boot order and firmware update/recovery information.

When you use the detail keyword, the boot order of the following available boot devices displays:

CDROM—Bootable CD-ROM
FDD—Floppy disk drive
HDD—Hard disk drive
PXE—PXE boot
EFI—Extensible Firmware Interface

Examples

This example shows how to display the server boot order:

server# show bios

BIOS Version                             Boot Order                   
---------------------------------------- ---------------------------- 
C250.1.1.0.6.031920100857                (none)  
server#

Related Commands

Command	Description
set boot-order
recover

show boot

To display information about the boot table of the host Fibre Channel interface, use the show boot command.

show boot [detail]

Syntax Description

detail

(Optional) Displays detailed information about the boot table in list format.

Command Default

None

Command Modes

Host Fibre Channel interface (/chassis/adapter/host-fc-if )

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to display the boot table of the host Fibre Channel interface.

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # show boot
Boot Table Entry Boot Target WWPN Boot LUN ID
----------------- -------------------------- ------------
0 20:00:00:11:22:33:44:55 3
1 20:00:00:11:22:33:44:56 5

Server /chassis/adapter/host-fc-if #

Related Commands

Command	Description
create-boot-entry
delete boot

show capabilities

To display RAID levels supported by a storage adapter, use the show capabilities command.

show capabilities [detail]

Syntax Description

detail

(Optional) Displays detailed information in list format.

Command Default

None

Command Modes

Storage adapter (/chassis/storageadapter)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example shows how to display RAID levels supported by a storage adapter in the SAS PCI slot:

server# scope chassis
server /chassis # scope storageadapter SAS
server /chassis/storageadapter # show capabilities
PCI Slot SAS:
        RAID-0
        RAID-1
        RAID-5
        RAID-6
        RAID-00
        RAID-10
        RAID-50
        RAID-60
        RAID-1e-rlq0
        RAID-1e0-rlq0
        RAID-srl-03

server /chassis/storageadapter #

Related Commands

Command	Description
show storageadapter

show certificate

To display informaion about the server certificate, use the show certificate command.

show certificate [ detail ]

Syntax Description

detail

(Optional) Displays the whole certificate.

Command Default

None

Command Modes

Root (server#)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

show certificate displays the serial number of the certificate, and the dates the certificate is valid for. show certificate detail in root mode and show detail in certificate mode displays the whole certificate.

Examples

This example shows how to display the serial number of the certificate, and the dates the certificate is valid for:

server# show certificate

Serial Number    Valid From               Valid To                 
---------------- ------------------------ ------------------------ 
001              Apr 13 13:49:00 2009 GMT Apr 11 13:49:00 2019 GMT

server#

This example shows how to display the whole certificate:

server# show certificate detail

Certificate Information:
    Serial Number: 00
    Subject Country Code (CC): US
    Subject State (S): California
    Subject Locality (L): San Jose
    Subject Organization (O): ABC Inc.
    Subject Organizational Unit (OU): 
    Subject Common Name (CN): abcinc.com
    Issuer Country Code (CC): US
    Issuer State (S): California
    Issuer Locality (L): San Jose
    Issuer Organization (O): Cisco Systems Inc.
    Issuer Organizational Unit (OU): 
    Issuer Common Name (CN): cisco.com
    Valid From: Sep  8 22:53:59 2009 GMT
    Valid To: Sep  6 22:53:59 2019 GMT

server#

Related Commands

Command	Description
generate-csr
upload

show chassis

To display information about the chassis, use the show chassis command.

show chassis [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the chassis, in list format.

Command Default

None

Command Modes

Root (server#)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

show chassis displays information about the chassis in table format. show chassis detail and show detail in chassis mode displays serial number, product name, PID, UUID, and description. Additionally, it displays chassis power state and the state of the locator LED.

Examples

This example shows how to display information about the chassis in table format:

server# show chassis

Power Serial Number Product Name  UUID                                 
----- ------------- ------------- ------------------------------------ 
on    QTF-0934-00   R100-1120402  208F4277020FBADBADBEA80000DEAD00
     
server#

Related Commands

Command	Description
set locator-led

show cimc

To display information about CIMC, use the show cimc command.

show cimc [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about CIMC, in list format.

Command Default

None

Command Modes

Root (server#)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

show cimc displays information about CIMC in table format. show cimc detail and show detail in cimc mode displays firmware version and boot loader version.

Examples

This example shows how to display information about CIMC in table format:

server# show cimc

Firmware Version     Current Time             
-------------------- ------------------------ 
1.0(0.86)            Fri Oct  2 12:19:17 2009
 
server#

Related Commands

Command	Description
show firmware
show log (cimc)

show comp-queue

To display information about the completion queue of the host Ethernet interface, use the show comp-queue command.

show comp-queue [detail]

Syntax Description

detail

(Optional) Displays detailed information in list format.

Command Default

None

Command Modes

Host Ethernet interface (/chassis/adapter/host-eth-if)

VM FEX interface (/chassis/adapter/vmfex)

Command History

Release	Modification
1.2(1)	This command was introduced.
1.4(1)	This command was added to the VM FEX interface.

Examples

This example shows how to display information about the completion queue of the host Ethernet interface:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # show comp-queue
Completion Queue Count    Completion Queue Ring Size 
------------------------- -------------------------- 
5                         1                          

Server /chassis/adapter/host-eth-if #

Related Commands

Command	Description
set cq-count

show configuration pending

To display uncommitted configuration commands, use the show configuration pending command.

show configuration pending

This command has no arguments or keywords.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example displays uncommitted configuration commands:

server /cimc/network *# show configuration pending
 
Modify  /cimc/network  
  hostname  SanJoseServer3  
  dhcp-enabled  yes  
  v4-addr  10.20.30.111  
  dns-use-dhcp  yes  

server /cimc/network *#

Related Commands

Command	Description
commit
discard

show cpu (chassis)

To display information about the CPU, use the show cpu command in the chassis mode.

show cpu [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the CPU, in list format.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

show cpu displays a list of CPUs. show cpu detail displays information for each CPU .

Following are commands you use to manage your view of the list of CPUs:

Enter key—Next line
Space bar—Next page
q key—Quit
r key—Show the rest

Examples

This example shows how to display detailed information about the CPUs:

server# scope chassis
server /chassis # show cpu detail

Name CPU1:
    Manufacturer: Intel(R) Corporation
    Family: Xeon
    Thread Count : 8
    Cores : 4
    Serial No.: Not Specified
    Version: Intel(R) Xeon(R) CPU           L5520  @ 2.27GHz
    Speed (Mhz) : 2266
    Max. Speed (Mhz) : 4000
    Signature: "Signature: Type 0, Family 6, Model 26, Stepping 5
    Status: Enabled
Name CPU2:
    Manufacturer: Intel(R) Corporation
    Family: Xeon
    Thread Count : 8
    Cores : 4
    Serial No.: Not Specified
    Version: Intel(R) Xeon(R) CPU           L5520  @ 2.27GHz
    Speed (Mhz) : 2266
    Max. Speed (Mhz) : 4000
    Signature: "Signature: Type 0, Family 6, Model 26, Stepping 5
    Status: Enabled

server /chassis #

Related Commands

Command	Description
show dimm
show psu

show current (sensor)

To display information about the status of the current sensors, use the show current command in sensor mode.

show current [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the status of the voltage sensors in list form.

Command Default

None

Command Modes

Sensor (/sensor)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to display information about the status of the current sensors:

server# scope sensor
server /sensor # show current detail
Name VR_CPU1_IOUT:
    Sensor Status: Normal
    Reading: 15.65
    Units: AMP
    Min. Warning: N/A
    Max. Warning: 152.68
    Min. Failure: N/A
    Max. Failure: 164.04
Name VR_CPU2_IOUT:
    Sensor Status: Normal
    Reading: 11.39
    Units: AMP
    Min. Warning: N/A
    Max. Warning: 152.68
    Min. Failure: N/A
    Max. Failure: 164.04

server /sensor #

show dimm (chassis)

To display information about the DIMMs (dual inline memory modules) in the chassis, use the show dimm command in chassis mode.

show dimm [detail]

Syntax Description

detail

(Optional) Displays detailed information about the DIMMs, in list format.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.0(1)	This command was introduced.
1.3(1)	This command was modified to display enhanced property information.

Usage Guidelines

This command can display many screen pages of information. Following are commands you use to manage your view of the list of DIMMs:

Enter key—Next line
Space bar—Next page
q key—Quit
r key—Show the rest

The detailed enhanced properties are described in the following table:

Name	Description
Name column	The name of the DIMM slot in which the memory module is installed.
Capacity column	The size of the DIMM.
Channel Speed column	The clock speed of the memory channel, in megahertz.
Channel Type column	The type of memory channel.
Memory Type Detail column	The type of memory used in the device.
Bank Locator column	The location of the DIMM within the memory bank.
Manufacturer column	The vendor ID of the manufacturer. This can be one of the following: 0x2C00—Micron Technology, Inc. 0x5105—Qimonda AG i. In. 0x802C—Micron Technology, Inc. 0x80AD—Hynix Semiconductor Inc. 0x80CE—Samsung Electronics, Inc. 0x8551—Qimonda AG i. In. 0xAD00—Hynix Semiconductor Inc. 0xCE00—Samsung Electronics, Inc.
Serial Number column	The serial number of the DIMM.
Asset Tag column	The asset tag associated with the DIMM, if any.
Part Number column	The part number for the DIMM assigned by the vendor.
Visibility column	Whether the DIMM is available to the server.
Operability column	Whether the DIMM is currently operating correctly.
Data Width column	The amount of data the DIMM supports, in bits.

Examples

This example shows how to display detailed information about the DIMMs:

server# scope chassis
server /chassis # show dimm detail

Name MEM1 DIMM_1B:
    Capacity: 8192 MB
    Channel Speed (MHz): 1067
    Channel Type: DDR3
    Memory Type Detail: Synchronous
    Bank Locator: MEM1 SLOT
    Visibility: Yes
    Operability: NA
    Manufacturer: 0x802C
    Part Number: 36JSZS1G72PY-1G1A1
    Serial Number: 0xEA27C463
    Asset Tag: Unknown
    Data Width: 72 bits
Name MEM1 DIMM_1A:
    Capacity: 8192 MB
    Channel Speed (MHz): 1067
    Channel Type: DDR3
    Memory Type Detail: Synchronous
    Bank Locator: MEM1 SLOT
    Visibility: Yes
    Operability: NA
    Manufacturer: 0x802C
    Part Number: 36JSZS1G72PY-1G1A1
--More--

Related Commands

Command	Description
show cpu

show entries (log)

To display the CIMC event log, use the show entries command in log mode.

show entries [ detail ]

Syntax Description

detail

(Optional) Displays the CIMC event log in detail.

Command Default

None

Command Modes

Log (/cimc/log)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

show entries displays trace log entries in continuous string format. show entries detail displays time, source, and description for each trace log entry, in list format.

Following are commands you use to manipulate your view of the log:

Enter key—Next line
Space bar—Next page
q key—Quit
r key—Show the rest

Examples

This example shows how to display the detailed event log:

server# scope cimc
server /cimc # scope log
server /cimc/log # show entries detail

Trace Log:
    Time: 2010 Jun 6 15:52:18
    Source: BMC:AUDIT:-
    Description: Session open (user:admin, ip:10.21.115.69, id:45, type:CLI)
    Order: 0
Trace Log:
    Time: 2010 Jun 6 15:52:18
    Source: BMC:dropbear:-
    Description: "  pam_session_manager(sshd:session): session (45) opened for user admin from 10.21.115.69 by (uid=0) "
    Order: 1
Trace Log:
    Time: 2010 Jun 6 15:52:18
    Source: BMC:AUDIT:-
    Description: Login success (user:admin, ip:10.21.115.69, service:sshd)
    Order: 2
Trace Log:
    Time: 2010 Jun 6 15:52:18
    Source: BMC:dropbear:-
    Description: "  pam_auth_status(sshd:session): Login Successfull for user=admin, host=10.21.115.69 "
    Order: 3
Trace Log:
--More--

Related Commands

Command	Description
show entries (sel)

show entries (sel)

To display the system event log, use the show entries command in sel mode.

show entries [ detail ]

Syntax Description

detail

(Optional) Displays the system event log in detail.

Command Default

None

Command Modes

SEL (/sel )

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

show entries displays system event log entries in continuous strings. show entries detail displays time, source, and description for each system event log entry, in list format.

Following are commands you use to manipulate your view of the log:

Enter key—Next line
Space bar—Next page
q key—Quit
r key—Show the rest

Examples

This example shows how to display the system event log:

server# scope sel
server /sel # show entries

System Event Log:
    Time: 2010-06-05 22:19:55
    Severity: Warning
    Description: " FRU_RAM P1V5_IOH: Voltage sensor for FRU_RAM, failure event was deasserted"
System Event Log:
    Time: 2010-06-05 22:19:55
    Severity: Critical
    Description: " FRU_RAM P1V5_IOH: Voltage sensor for FRU_RAM, non-recoverable event was deasserted"
System Event Log:
    Time: 2010-06-05 22:19:49
    Severity: Non-Recoverable
    Description: " FRU_RAM P1V5_IOH: Voltage sensor for FRU_RAM, non-recoverable event was asserted"
System Event Log:
    Time: 2010-06-05 22:19:49
    Severity: Critical
    Description: " FRU_RAM P1V5_IOH: Voltage sensor for FRU_RAM, failure event was asserted"
System Event Log:
    Time: 2010-06-05 19:45:32
    Severity: Warning
--More--

Related Commands

Command	Description
show entries (log)

show error-counters

To display the number of errors seen by a storage adapter, use the show error-counters command.

show error-counters [detail]

Syntax Description

detail

(Optional) Displays detailed information in list format.

Command Default

None

Command Modes

Storage adapter (/chassis/storageadapter)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example shows how to display the number of errors seen by a storage adapter in the SAS PCI slot:

server# scope chassis
server /chassis # scope storageadapter SAS
server /chassis/storageadapter # show error-counters
PCI Slot SAS:
    Memory Correctable Errors: 0
    Memory Uncorrectable Errors: 0

server /chassis/storageadapter #

Related Commands

Command	Description
show storageadapter

show error-recovery

To display information about the Fibre Channel error recovery, use the show error-recovery command.

show error-recovery [detail]

Syntax Description

detail

(Optional) Displays detailed information about the error-recovery in list format.

Command Default

None

Command Modes

Host Fibre Channel Interface (/chassis/adapter/host-fc-if)

Command History

Release	Modification
1.2(1)	This command was introduced.

Usage Guidelines

Use this command to show details of the host Fibre Channel interface errror recovery.

Examples

This example shows how to display the error recovery of the host Fibre Channel interface:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if show error-recovery
Error Recovery Link Down Timeout(ms)  Port Down Timeout(ms)  
-------------- ---------------------- ---------------------- 
Disabled       30000                  10000                  
Server /chassis/adapter/host-fc-if/error-recovery #

Related Commands

Command	Description
set cq-count

show ext-eth-if

To display information about the external Ethernet interface, use the show ext-eth-if command.

show ext-eth-if [detail]

Syntax Description

detail

(Optional) Displays detailed information in list format.

Command Default

None

Command Modes

Adapter (/chassis/adapter)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to display the external Ethernet interface:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # show ext-eth-if
Port ID Uplink port MAC address  Link State          Encapsulation Mode   
------- ------------------------ ------------------- -------------------- 
0       00:22:BD:D6:40:E0        Link Up             CE                   
1       00:22:BD:D6:40:E1        SFP Not Installed   CE         

Server /chassis/adapter #

Related Commands

Command	Description
show host-eth-if

show fan (sensor)

To display information about the fan sensors, use the show fan command in sensor mode.

show fan [ detail ]

Syntax Description

detail

(Optional) Displays .

Command Default

None

Command Modes

Sensor (/sensor)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to display information about the fan sensors:

Server# scope sensor
Server /sensor # show fan

Name                 Sensor Status        Reading    Units      Min. Warning    Max. Warning    Min. Failure    Max. Failure    
-------------------- -------------------- ---------- ---------- --------------- --------------- --------------- --------------- 
PSU1_FAN_1           Normal               6592       RPM        N/A             N/A             N/A             N/A             
PSU2_FAN_1           Normal               2560       RPM        N/A             N/A             N/A             N/A             
W793_FAN1_TACH1      Normal               5300       RPM        N/A             N/A             800             N/A             
W793_FAN1_TACH2      Normal               5400       RPM        N/A             N/A             800             N/A             
W793_FAN2_TACH1      Normal               5500       RPM        N/A             N/A             800             N/A             
W793_FAN2_TACH2      Normal               5400       RPM        N/A             N/A             800             N/A             
W793_FAN3_TACH1      Normal               5300       RPM        N/A             N/A             800             N/A             
W793_FAN3_TACH2      Normal               5500       RPM        N/A             N/A             800             N/A             
W793_FAN4_TACH1      Normal               5300       RPM        N/A             N/A             800             N/A             
W793_FAN4_TACH2      Normal               5500       RPM        N/A             N/A             800             N/A             
--More-- 

Server /sensor # show fan detail
Name PSU1_FAN_1:
    Sensor Status: Normal
    Reading: 7872
    Units: RPM
    Min. Warning: N/A
    Max. Warning: N/A
    Min. Failure: N/A
    Max. Failure: N/A
Name PSU2_FAN_1:
    Sensor Status: Normal
    Reading: 2496
    Units: RPM
    Min. Warning: N/A
    Max. Warning: N/A
    Min. Failure: N/A
    Max. Failure: N/A
Name W793_FAN1_TACH1:
    Sensor Status: Normal
    Reading: 5300
    Units: RPM
    Min. Warning: N/A
    Max. Warning: N/A
    Min. Failure: 800
    Max. Failure: N/A
Name W793_FAN1_TACH2:
    Sensor Status: Normal
    Reading: 5400
    Units: RPM
    Min. Warning: N/A
    Max. Warning: N/A
    Min. Failure: 800
    Max. Failure: N/A
Name W793_FAN2_TACH1:
    Sensor Status: Normal
    Reading: 5500
    Units: RPM
    Min. Warning: N/A
    Max. Warning: N/A
    Min. Failure: 800
    Max. Failure: N/A
Name W793_FAN2_TACH2:
    Sensor Status: Normal
--More--

Related Commands

Command	Description
show cpu

show fan-policy

To view information on the configured fan policy, use the show fan-policy command.

show fan-policy detail

Syntax Description

detail

Displays detailed information on the configured fan policy.

Command Default

Displays information on the fan policy in a tabular format

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.5(2)	This command was introduced.

Usage Guidelines

None

Examples

This example shows how to view information on the configured fan policy:

server # scope chassis
server /chassis # show fan-policy

Fan Policy
----------
Balanced

server /chassis #

Related Commands

Command	Description
scope fan-policy
set fan-policy

show fault

To display whether platform event alerts are enabled or disabled on the server, use the show fault command.

show fault [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about SNMP services, in list format.

Command Default

None

Command Modes

Root (server#)

Command History

Release	Modification
1.0(1)	This command was introduced.
1.4(1)	This command was modified to remove display of the SNMP community string.

Usage Guidelines

This command displays whether platform event alerts are enabled or disabled.

Examples

This example shows how to display whether platform event alerts are enabled or disabled:

server# show fault

Platform Event Enabled
----------------------
yes

server#

Related Commands

Command	Description
show pef
show trap-destination

show fault-entries

To view the fault logs, use the show fault-entries command.

show fault-entries detail

Syntax Description

detail

(Optional) Displays detailed information on the fault logs.

Command Default

Lists the fault entries in a tabular format

Command Modes

Faults (/fault)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must be an admin to use this command.

Examples

This example shows how to view the fault logs for the server:

Server # scope fault
Server /fault # show fault-entries
Time                     Severity      Description
------------------------ ------------ -----------------
Sun Jun 27 04:00:52 2013  info        Storage Local disk 12 missing
Sat Jun 26 05:00:22 2013  warning     Power Supply redundancy is lost
            
Server /fault #

Related Commands

Command	Description
scope fault
show pef
show pef-destinations

show firmware (cimc)

To display information about the firmware on the server, use the show firmware command in cimc mode.

show firmware [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about firmware, in list format.

Command Default

None

Command Modes

CIMC (/cimc)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

show firmware displays information about firmware in table format. show firmware detail and show detail in firmware mode display information about updates, firmware version, and boot loader version.

Examples

This example shows how to display information about updates, firmware version, and boot loader version:

server# scope cimc
server /cimc # show firmware detail
Firmware Image Information:
    Update Stage: NONE
    Update Progress: 0
    Current FW Version: 1.1(0.3)
    FW Image 1 Version: 1.1(0.3)
    FW Image 1 State: BACKUP INACTIVATED
    FW Image 2 Version: 1.1(0.3)
    FW Image 2 State: RUNNING ACTIVATED
    Boot-loader Version: 1.1(0.3)
server /cimc #

Related Commands

Command	Description
show cimc
show version

show firmware (/flexflash)

To display information about the firmware version installed on the Cisco Flexible Flash card, use the show firmware command.

show firmware detail

Syntax Description

detail

(Optional) Displays detailed information on the installed firmware version, in the list format.

Command Default

None

Command Modes

FlexFlash (/chassis/flexflash)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

The show firmware command displays information about the firmware in a tabular format. The show firmware detail command displays information in a list format.

Examples

This example shows how to display firmware information in a list format:

Server # scope chassis
Server /chassis # scope flexflash FlexFlash-0
Server /chassis/flexflash # show firmware detail

Controller FlexFlash-0:
  Product Name: Cisco FlexFlash
  Firmware Version: 1.2(1)
  Running Firmware: 1.2(1)
  Startup Firmware Version: 1.2(2)

Server /chassis/flexflash #

Related Commands

Command	Description
show operational-profile
show physical-drive
show physical-drive-count
show virtual-drive
show virtual-drive-count

show firmware-versions

To display firmware version information for a storage adapter, use the show firmware-versions command.

show firmware-versions [detail]

Syntax Description

detail

(Optional) Displays detailed information in list format.

Command Default

None

Command Modes

Storage adapter (/chassis/storageadapter)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example shows how to display firmware version information for a storage adapter in the SAS PCI slot:

server# scope chassis
server /chassis # scope storageadapter SAS
server /chassis/storageadapter # show firmware-versions
PCI Slot SAS:
    Product Name: LSI MegaRAID SAS 9260-8i
    Serial No: SV93404392
    Firmware Package Build: 12.12.0-0038

server /chassis/storageadapter #

Related Commands

Command	Description
show storageadapter

show flexflash

To display summary information about installed Cisco Flexible Flash controllers, use the show flexflash command.

show flexflash [index] [detail]

Syntax Description

index	(Optional) The name of the Cisco Flexible Flash controller.
detail	(Optional) Displays detailed information in list format.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.3(3)	This command was introduced.

Examples

This example shows how to display information about the first flash device:

Server# scope chassis
Server /chassis # show flexflash FlexFlash-0
Controller   Product Name     Has Error  Firmware Version  Vendor   Internal State
------------ ---------------- ---------- ----------------- -------- ---------------
FlexFlash-0  Cisco FlexFlash  No         1.2 build 247     Cypress  Connected   

Server /chassis #

Related Commands

Command	Description
show operational-profile

show gpu

To view available Nvidia GPU cards on the system, use the show gpu command.

show gpu detail

Syntax Description

detail

Displays detailed information on the available Nvidia GPU card instead of the default brief mode.

Command Default

Information on the Nvidia card is displayed in the brief mode.

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

This command is only available on Cisco UCS C-240 servers.

The server must be powered on to use this command.

Examples

This example shows how to view the available Nvidia GPU cards on the system:

Server # scope chassis
Server /chassis # show gpu

Slot         Product Name              Num of GPUs
----         ------------              -----------
5            Nvidia GRID K2 @ BD        2

Server /chassis #

Related Commands

Command	Description
scope gpu
show gpu list

show gpu-list

To view the temperatures of the GPU cards on the system, use the show gpu-list command.

show gpu-list

This command has no arguments or keywords.

Command Default

None

Command Modes

GPU card (/chassis/gpu)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

This command is only available on Cisco UCS C-240 servers.

The server must be powered on to use this command.

Examples

This example shows how to view the temperature information of the Nvidia GPU cards on the system:

Server # scope chassis
Server /chassis # show gpu

Slot         Product Name              Num of GPUs
----         ------------              -----------
5            Nvidia GRID K2 @ BD        2

Server /chassis # scope gpu 5
Server /chassis/gpu # show gpu-list

GPU ID        Temperature
------        -----------
0               32
1               33
2               n/a
3               n/a

Server /chassis/gpu #

show hdd (chassis)

To display information about installed hard disk drives (HDD) in the chassis, use the show hdd command.

show hdd [detail]

Syntax Description

detail

(Optional) Displays detailed information about the HDDs in list form.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to display information about hard disk drives in the chassis:

Server# scope chassis
Server /chassis # show hdd
Name                 Status               
-------------------- -------------------- 
HDD_01_STATUS        present              
HDD_02_STATUS        present              
HDD_03_STATUS        present              
HDD_04_STATUS        present     

Server /chassis # show hdd detail
Name HDD_01_STATUS:
    Status : present
Name HDD_02_STATUS:
    Status : present
Name HDD_03_STATUS:
    Status : present
Name HDD_04_STATUS:
    Status : present

Server /chassis #

Related Commands

Command	Description
show psu

show host-eth-if

To display information about a host Ethernet interface, use the show host-eth-if command.

show host-eth-if [ eth0 | eth1 | name ] [detail]

Syntax Description

eth0	(Optional) Displays information about the eth0 Ethernet interface.
eth1	(Optional) Displays information about the eth1 Ethernet interface.
name	(Optional) Displays information about the named Ethernet interface.
detail	(Optional) Displays detailed information in list form.

Command Default

None

Command Modes

Adapter (/chassis/adapter)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to display information about the eth0 Ethernet interface of adapter card 1:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # show host-eth-if eth0
Name             MTU  Uplink Port MAC Address       CoS VLAN PXE Boot 
---------------- ---- ----------- ----------------- --- ---- -------- 
eth0             1500 0           00:22:BD:D6:40:E3 0   NONE enabled  
 
Server /chassis/adapter #

Related Commands

Command	Description
show ext-eth-if

show host-fc-if

To display information about the host Fibre Channel interface, use the show host-fc-if command.

show host-fc-if [ fc0 | fc1 | name ] [detail]

Syntax Description

fc0	(Optional) Displays information about vHBA fc0.
fc1	(Optional) Displays information about vHBA fc1.
name	(Optional) Displays information about a user-defined vHBA.
detail	(Optional) Displays detailed information in list form.

Command Default

None

Command Modes

Adapter (/chassis/adapter)

Command History

Release	Modification
1.2(1)	This command was introduced.
1.4(1)	This command was modified to add the name variable.

Examples

This example shows how to display all vHBAs on adapter card 1 and the detailed properties of fc0:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # show host-fc-if
Name     World Wide Port Name     FC SAN Boot Uplink Port 
-------- ------------------------ ----------- ----------- 
fc0      20:00:00:22:BD:D6:5C:35  Enabled     0           
fc1      20:00:00:22:BD:D6:5C:36  Disabled    1    

Server /chassis/adapter # show host-fc-if fc0 detail
Name fc0:
    World Wide Node Name: 10:00:00:22:BD:D6:5C:35
    World Wide Port Name: 20:00:00:22:BD:D6:5C:35
    FC SAN Boot: Enabled
    Persistent LUN Binding: Disabled
    Uplink Port: 0
    MAC Address: 00:22:BD:D6:5C:35
    CoS: 3
    VLAN: NONE
    Rate Limiting: OFF
    PCIe Device Order: ANY
    EDTOV: 2000
    RATOV: 10000
    Maximum Data Field Size: 2112
    Channel Number: 3
    Port Profile:

Server /chassis/adapter #

Related Commands

Command	Description
create host-fc-if

show http

To display information about HTTP services on the server, use the show http command.

show http [ detail ]

Syntax Description

detail

(Optional) Displays detailed information in list format.

Command Default

None

Command Modes

Root (server#)

Command History

Release	Modification
1.0(1)	This command was introduced.

Usage Guidelines

Use this command to display information about HTTP ports, session timeout, and session activity.

Examples

This example shows how to display information about HTTP services:

Server# show http
HTTP Port  HTTPS Port Timeout  Active Sessions Enabled HTTP Redirected  
---------- ---------- -------- --------------- ------- ---------------- 
80         443        1800     0               yes     yes   
     
Server#

Related Commands

Command	Description
set http-port
set https-port

show hw-config

To display hardware information for a storage adapter, use the show hw-config command.

show hw-config [detail]

Syntax Description

detail

(Optional) Displays detailed information in list format.

Command Default

None

Command Modes

Storage adapter (/chassis/storageadapter)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example shows how to display hardware information for a storage adapter in the SAS PCI slot:

server# scope chassis
server /chassis # scope storageadapter SAS
server /chassis/storageadapter # show hw-config
PCI Slot SAS:
    SAS Address 0: 500605b0000272bf
    SAS Address 1: 0000000000000000
    SAS Address 2: 0000000000000000
    SAS Address 3: 0000000000000000
    SAS Address 4: 0000000000000000
    SAS Address 5: 0000000000000000
    SAS Address 6: 0000000000000000
    SAS Address 7: 0000000000000000
    BBU Present: true
    NVRAM Present: true
    Serial Debugger Present: true
    Memory Present: true
    Flash Present: true
    Memory Size: 512 MB
    Cache Memory Size: 394 MB
    Number of Backend Ports: 8

server /chassis/storageadapter #

Related Commands

Command	Description
show storageadapter

show interrupt

To display information about the interrupt of the host Ethernet interface or the host Fibre Channel Interface, use the show interrupt command.

show interrupt

Syntax Description

detail

(Optional) Displays detailed information in list format.

Command Modes

Host Ethernet interface (/chassis/adapter/host-eth-if )

Host Fibre Channel interface (/chassis/adapter/host-fc-if )

VM FEX interface (/chassis/adapter/vmfex)

Command History

Release	Modification
1.2(1)	This command was introduced.
1.4(1)	This command was added to the VM FEX interface.

Examples

This example shows how to display the interrupt of the host Ethernet interface:


Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0 
Server /chassis/adapter/host-eth-if # show interrupt
Interrupt Count Coalescing Time (us) Coalescing Type Interrupt Mode  
--------------- -------------------- --------------- --------------- 
8               125                  MIN             MSIx        

Server /chassis/adapter/host-eth-if #

Related Commands

Command	Description
set interrupt-type

show ipblocking (network)

To display information about the network IP blocking configuration, use the show ipblocking command in network mode.

show ipblocking [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the IP blocking configuration in list format.

Command Default

None

Command Modes

IP blocking (/cimc/network)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to display information about the IP blocking configuration:

server# scope cimc
Server /cimc # scope network      
server /cimc/network # show ipblocking detail

IP Blocking Setting:
    Enabled: no
    Fail Count: 5
    Fail Window: 60
    Blocking Time: 300

server /cimc/network #

Related Commands

Command	Description
show network

show ipmi

To display information about the configuration and status of IPMI (Intelligent Platform Management Interface) on the server, use the show ipmi command.

show ipmi [detail]

Syntax Description

detail

(Optional) Displays detailed iinformation about the configuration and status of IPMI on the server in list format.

Command Default

None

Command Modes

Root (server#)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to display information about the configuration and status of IPMI:

server# show ipmi detail

IPMI over LAN Settings:
    Enabled: yes
    Encryption Key: abcdef01234567890abcdef01234567890abcdef
    Privilege Level Limit: admin

server#

Related Commands

Command	Description
set enabled (ipmi)
set encryption-key (ipmi)

show iscsi-boot

To display information about the iSCSI boot configuration for a vNIC, use the show iscsi-boot command.

show iscsi-boot detail

Syntax Description

detaill

(Optional) Displays detailed information on the iSCSI boot configuration

Command Default

None

Command Modes

Host Ethernet Interface (/chassis/adapter/host-eth-if)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

None

Examples

This example shows how to display information on the iSCSI boot configuration for a vNIC:

Server # scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # show iscsi-boot 

Index DHCP Network DHCP iSCSI IQN                     IP Address      Gateway
----- ------------ ---------- ----------------------- --------------- --------
0     enabled      disabled   alkjdshfalkhfalsdjhf...

Server /chassis/adapter/host-eth-if #

show kvm

To display information about the KVM, use the show kvm command.

show kvm [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the KVM in list format.

Command Default

None

Command Modes

Root (server#)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to display information about the KVM:

server# show kvm

Encryption Enabled Local Video      Active Sessions Enabled KVM Port 
------------------ ---------------- --------------- ------- -------- 
no                 no               0               yes     2068
     
server#

Related Commands

Command	Description
set kvm-port
set max-sessions (kvm)

show ldap

To display information about the configuration and status of Active Directory, use the show ldap command.

show ldap [detail]

Syntax Description

detail

(Optional) Displays detailed information about the configuration and status of Active Directory in list format.

Command Default

None

Command Modes

Root (server#)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to display information about the configuration and status of Active Directory:

Server# show ldap detail
LDAP Settings:
    Domain Controller 1: 192.0.20.123
    Domain Controller 2: 0.0.0.0
    Domain Controller 3: 0.0.0.0
    BaseDN: example.com
    Encrypted: no
    Timeout: 60
    Enabled: no
    Attribute: CiscoAvPair
    Group Authorization: yes
    Global Catalog 1: 192.0.20.11
    Global Catalog 2: 0.0.0.0
    Global Catalog 3: 0.0.0.0

Server#

Related Commands

Command	Description
set base-dn
set dc

show led (chassis)

To display information about the server LEDs, use the show led command in the chassis command mode.

show led [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the server LEDs in list format.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to display information about the server LEDs:

server# scope chassis
server /chassis # show led

LED Name                  LED State  LED Color 
------------------------- ---------- -------- 
DDR3_P2_D1_INFO           OFF        AMBER    
DDR3_P1_A1_INFO           OFF        RED      
LED_HLTH_STATUS           ON         GREEN    
LED_FPID                  OFF        BLUE     
LED_PSU_STATUS            OFF        AMBER    
LED_DIMM_STATUS           ON         GREEN    
LED_CPU_STATUS            ON         GREEN

Related Commands

Command	Description
set locator-led

show local-syslog-severity

To display the lowest level of messages that are included in the CIMC log, use the show local-syslog-severity command.

show local-syslog-severity [detail]

Syntax Description

detail

Displays output in list form.

Command Default

None

Command Modes

CIMC log (/cimc/log)

Command History

Release	Modification
1.4(3)	This command was introduced.

Usage Guidelines

Use this command to display the lowest level of messages that are included in the CIMC log. The displayed minimum severity level can be one of the following, in decreasing order of severity:

emergency
alert
critical
error
warning
notice
informational
debug

Examples

This example displays the lowest level of messages that are included in the CIMC log:

Server# scope cimc
Server /cimc # scope log
Server /cimc/log # show local-syslog-severity
    Local Syslog Severity: warning

Server /cimc/log #

Related Commands

Command	Description
set local-syslog-severity

show log

To display information on the storage controllers, use the show log command.

show log detail

Syntax Description

detail

Displays all details on the logs.

Command Default

Displays log information in brief mode

Command Modes

Storage Adapter (/chassis/storageadapter)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must be logged in as an admin to use this command.

Examples

This example shows how to display storage controller logs:

Server # scope chassis
Server /chassis # scope storageadapter SLOT-3
Server /chassis/storageadapter # show log

Time                        Severity         Description
----                        --------        -------------
Fri March 1 09:52:19 2013   Warning      Predictive Failure
Fri March 1 07:50:19 2013   Info         Battery charge complete 
Fri March 1 07:50:19 2013   Info         Battery charge started
Fri March 1 07:48:19 2013   Info         Battery relearn complete
Fri March 1 07:47:19 2013   Info         Battery is discharging
Fri March 1 07:45:19 2013   Info         Battery relearn started

Server /chassis/storageadapter #

show lom-mac-list

To display the MAC addresses of the LAN On Motherboard (LOM) Ethernet host ports, use the show lom-mac-list command.

show lom-mac-list [detail]

Syntax Description

detail

(Optional) Displays detailed information in list format.

Command Default

None

Command Modes

Network (/cimc/network)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to display the MAC addresses of the LAN On Motherboard (LOM) Ethernet host ports.

Examples

This example shows how to display the MAC addresses of the LOM ports:

Server# scope cimc
Server /cimc # scope network
Server /cimc/network # show lom-mac-list
Interface       MAC Address          
--------------- -------------------- 
eth0            010000002000         
eth1            010000002000  

Server /cimc/network #

Related Commands

Command	Description
set mode

show main

To display the main BIOS configuration settings, use the show main command.

show main [detail]

Syntax Description

detail

(Optional) Displays detailed main BIOS configuration settings in list format.

Command Default

None

Command Modes

BIOS (/bios)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example displays the main BIOS configuration details:

Server# scope bios
Server /bios # show main detail
Set-up parameters:
    Boot option retry: Disabled
    POST Error Pause: Disabled

Server /bios #

Related Commands

Command	Description
scope main

show mappings

To display information on all CIMC-mapped vmedia volumes, use the show mappings command.

show mappings detail

Syntax Description

detail

(Optional) Displays detailed information on the CIMC-mapped vmedia volumes in a list format.

Command Default

None

Command Modes

vmedia (/vmedia)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must be logged in as an admin to use this command.

Examples

This example shows how to display information on all current local vmedia mapping:

Server # scope vmedia
Server /vmedia # show mappings detail

Volume: Sample
  Map status: "Stale (reason: bad file descriptor)"
  Drive Type: CD
  Remote-Share: //19.10.23.23/projects
  Remote-file: swbld/sample/file/name.iso
  Mount-type: cifs
  Mount-options: nolock,soft
  
Server /vmedia #

show mfg-data

To display manufacturer data for a storage adapter, use the show mfg-data command.

show mfg-data [detail]

Syntax Description

detail

(Optional) Displays detailed information in list format.

Command Default

None

Command Modes

Storage adapter (/chassis/storageadapter)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example shows how to display manufacturer data for a storage adapter in the SAS PCI slot:

server# scope chassis
server /chassis # scope storageadapter SAS
server /chassis/storageadapter # show mfg-data
PCI Slot SAS:
    Manufactured Date: 2009-09-19
    Rework Date: 
    Revision No: 
    Battery FRU: 

server /chassis/storageadapter #

Related Commands

Command	Description
show storageadapter

show network (cimc)

To display information about the server network configuration, use the show network command in cimc mode.

show network [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the server network configuration in list format.

Command Default

None

Command Modes

CIMC (/cimc)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to display information about the server network configuration:

server# scope cimc
server /cimc # show network

DHCP Enabled VLAN Enabled 
------------ ------------ 
no           no
           
server#

Related Commands

Command	Description
set dhcp-enabled
show ipblocking

show ntp

To display details about the Network Time Protocol (NTP) service settings, use the show ntp command.

show ntp detail

Syntax Description

detail

Displays detailed information about the NTP service settings.

Command Default

By default, this command displays if the NTP service is enabled or not.

Command Modes

Network (/cimc/network)

Command History

Release	Modification
1.5(1)	This command was introduced.

Examples

This example shows how to display information about the NTP service settings:

Server # scope cimc
Server /cimc # scope network
Server /cimc/network # show ntp detail

NTP Service Settings:
  Enabled: Yes
  Server 1: 1.2.3.4
  Server 2: 1.pool.ntp.org
  Server 3: 2.pool.ntp.org
  Server 4: 3.pool.ntp.org

Server /cimc/network #

Related Commands

Command	Description
scope ntp
set enabled
set server-1
set server-2
set server-3
set server-4

show offload

To display information about TCP offload of the host interface, use the show offload command.

show offload [detail]

Syntax Description

detail

(Optional) Displays detailed information in list format.

Command Default

None

Command Modes

Host Ethernet interface (/chassis/adapter/host-eth-if)

Host Fibre Channel interface (/chassis/adapter/host-fc-if)

VM FEX interface (/chassis/adapter/vmfex)

Command History

Release	Modification
1.2(1)	This command was introduced.
1.4(1)	This command was added to the VM FEX interface.

Examples

This example shows how to display the TCP offload of the host Ethernet interface:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # show offload
TCP Segment Offload  TCP Rx Checksum  TCP Tx Checksum  Large Receive 
-------------------- ---------------- ---------------- ------------- 
Enabled              Enabled          Enabled          Enabled   

Server /chassis/adapter/host-eth-if #

Related Commands

Command	Description
set tcp-segment-offload
set tcp-rx-checksum-offload
set tcp-tx-checksum-offload

show operational-profile

To display operational profile information about a Cisco Flexible Flash controller, use the show operational-profile command.

show operational-profile [detail]

Syntax Description

detail

(Optional) Displays detailed information in list format.

Command Default

None

Command Modes

FlexFlash (/chassis/flexflash)

Command History

Release	Modification
1.3(3)	This command was introduced.

Examples

This example shows how to display operational profile information about the first flash device:

Server# scope chassis
Server /chassis # scope flexflash FlexFlash-0
Server /chassis/flexflash # show operational-profile detail
FlexFlash Operational Profile:
    Primary Member Slot: slot1
    I/O Error Threshold: 0
    Host Accessible VDs: SCU HV Drivers HUU

Server /chassis/flexflash #

Related Commands

Command	Description
scope operational-profile

show pci-adapter

To display the properties of installed PCI adapters, use the show pci-adapter command.

show pci-adapter [detail]

Syntax Description

detail

(Optional) Displays detailed properties of installed PCI adapters in list format.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example displays the pci-adapter configuration details:

Server# scope chassis
Server /chassis # show pci-adapter
Name             Slot   Vendor ID        Device ID        Product Name              
---------------- ------ ---------------- ---------------- ------------------------- 
PCIe Adapter1    7      0x8086           0x10fb           Intel 10 Gbps 2 port x... 
PCIe Adapter2    6      0x14e4           0x164f           Broadcom 57711 10 Gbps... 
PCIe Adapter3    3      0x8086           0x10e8           Intel 1 Gbps 4 port E1... 
PCIe Adapter4    2      0x1077           0x8000           Qlogic QLE 8152-CNA 10... 

Server /chassis #

Related Commands

Command	Description
scope chassis

show pci-info

To display PCI information for a storage adapter, use the show pci-info command.

show pci-info [detail]

Syntax Description

detail

(Optional) Displays detailed information in list format.

Command Default

None

Command Modes

Storage adapter (/chassis/storageadapter)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example shows how to display PCI information for a storage adapter in the SAS PCI slot:

server# scope chassis
server /chassis # scope storageadapter SAS
server /chassis/storageadapter # show pci-info
PCI Slot SAS:
    Vendor ID: 1000
    Device ID: 79
    SubVendor ID: 1000
    SubDevice ID: 9261

server /chassis/storageadapter #

Related Commands

Command	Description
show storageadapter

show pef (fault)

To display information about the configuration and status of PEFs (Platform Event Filters), use the show pef command in fault mode.

show pef [ pef-number ] [ detail ]

Syntax Description

pef-number	Displays information about the specified PEF. If the pef-number variable is omitted, the command displays information about all PEFs.
detail	(Optional) Displays detailed information in list form.

Command Default

None

Command Modes

Fault (/fault)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to display information about the configuration and status of all PEFs:

Server# scope fault
Server /fault # show pef

Platform Event Filter Event                               Action      Send Alert         
--------------------- ----------------------------------- ----------- ------------------ 
1                     Temperature Critical Assert Filter  none        no                 
2                     Temperature Warning Assert Filter   none        no                 
3                     Voltage Critical Assert Filter      none        no                 
4                     Voltage Warning Assert Filter       none        no                 
5                     Current Assert Filter               none        no                 
6                     Fan Critical Assert Filter          none        no                 
7                     Fan Warning Assert Filter           none        no                 
8                     Processor Assert Filter             none        no                 
9                     Power Supply Critical Assert Filter none        no                 
10                    Power Supply Warning Assert Filter  none        no                 
11                    Power Supply Redundancy Lost Filter none        no                 
12                    Discrete Power Supply Assert Filter none        no                 
13                    Memory Assert Filter                none        no                 
14                    Drive Slot Assert Filter            none        no                 

server /fault #

Related Commands

Command	Description
set platform-event-enabled

show perbi

To display information about the persistent LUN binding of the host Fibre Channel interface, use the show perbi command.

show perbi [detail]

Syntax Description

detail

(Optional) Displays detailed information about the persistent LUN binding in list format.

Command Default

None

Command Modes

Host Fibre Channel interface (/chassis/adapter/host-fc-if)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to display information about the persistent LUN binding of the host Fibre Channel interface:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc 1
Server /chassis/adapter/host-fc-if # scope perbi
Server /chassis/adapter/host-fc-if/perbi # show
Server /chassis/adapter/host-fc-if/perbi #

Related Commands

Command	Description
scope perbi

show physical-drive

To display physical drive information for a storage adapter or for a virtual drive or for the Cisco Flexible Flash card, use the show physical-drive command.

show physical-drive drive-number [detail]

Syntax Description

drive-number	(Optional) The drive number of the physical drive.
detail	(Optional) Displays detailed information in list format.

Command Default

None

Command Modes

Storage adapter (/chassis/storageadapter)

Virtual drive (/chassis/storageadapter/virtual-drive)

FlexFlash (/chassis/flexflash)

Command History

Release	Modification
1.3(1)	This command was introduced.
1.5(1)	This command was introduced in the FlexFlash command mode.

Examples

This example shows how to display detailed physical drive information for physical drive number 1 on the storage adapter in the SAS PCI slot:

server# scope chassis
server /chassis # scope storageadapter SAS
server /chassis/storageadapter # show physical-drive 1 detail
Slot Number 1:
    Controller: SAS
    Status: online
    Manufacturer: FUJITSU
    Model: MBD2300RC
    Predictive Failure Count: 0
    Drive Firmware: 5701
    Coerced Size: 285568 MB
    Type: HDD

server /chassis/storageadapter #

This example shows how to display detailed physical drive information on the Cisco Flexible Flash card:

server# scope chassis
server /chassis # scope flexflash FlexFlash-0
server /chassis/flexflash # show physical-drive detail

Physical Drive Slot-1:
 Slot: 1
 Controller: FlexFlash-0
 Role: Primary
 Health: Healthy
 Status: present
 Card Type: SD253 card
 Capacity: 15806 MB
 Write enabled: true
 Read Error Count: 20
 Read Error Threshold: 30
 Write Error Count: 15
 Write Error Threshold: 30
 Product Name: DST
 Product revision: 1.0
 Serial# : 0x3103
 Manufacturer ID: 1111
 OEM ID: 
 Manufacturing date: 5/12
 Block size: 512 bytes
 Password Protected: false
 Partition Count: 4
 Drives enabled: SCU HV Drivers, HUU
 RAID Signatures: 6f1300000000000000000

Physical Drive Slot-2: 
 Slot: 2
 Controller: FlexFlash-0
 Role: Secondary
 Health: Healthy
 Status: present
 Card Type: SD253 card
 Capacity: 15806 MB
 Write enabled: true
 Read Error Count: 20
 Read Error Threshold: 30
 Write Error Count: 15
 Write Error Threshold: 30
 Product Name: DST
 Product revision: 1.0
 Serial# : 0x3103
 Manufacturer ID: 1111
 OEM ID: 
 Manufacturing date: 5/12
 Block size: 512 bytes
 Password Protected: false
 Partition Count: 4
 Drives enabled: SCU HV Drivers, HUU
 RAID Signatures: 6f1300000000000000000

server /chassis/flexflash #

Related Commands

Command	Description
show storageadapter
show flexflash

show physical-drive-count

To display the number of physical drives for a storage adapter, use the show physical-drive-count command.

show physical-drive-count [detail]

Syntax Description

detail

(Optional) Displays detailed information in list format.

Command Default

None

Command Modes

Storage adapter (/chassis/storageadapter)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example shows how to display the number of physical drives on the storage adapter in the SAS PCI slot:

server# scope chassis
server /chassis # scope storageadapter SAS
server /chassis/storageadapter # show physical-drive-count
PCI Slot SAS:
    Physical Drive Count: 12
    Critical Physical Drive Count: 1
    Failed Physical Drive Count: 0

server /chassis/storageadapter #

Related Commands

Command	Description
show storageadapter

show port

To display port information about the host Fibre Channel interface, use the show port command.

show port [detail]

Syntax Description

detail

(Optional) Displays detailed port information in list format.

Command Default

None

Command Modes

Host Fibre Channel interface (/chassis/adapter/host-fc-if)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to display port information for the host Fibre Channel interface:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # show port
I/O Throttle Count   Maximum LUNS per Target  
-------------------- ------------------------ 
512                  256                      

Server /chassis/adapter/host-fc-if #

Related Commands

Command	Description
show port-p-logi
show port-f-logi

show port-f-logi

To display information about the Fibre Channel fabric login, use the show port-f-logi command.

show port-f-logi [detail]

Syntax Description

detail

(Optional) Displays detailed information about the fabric login in list format.

Command Default

None

Command Modes

Host Fibre Channel interface (/chassis/adapter/host-fc-if )

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to display information about the fabric login of the host interface:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # show port-f-logi
FLOGI Retries FLOGI Timeout (milli-secs)   
------------- ---------------------------- 
INFINITE      2000                              

Server /chassis/adapter/host-fc-if #

Related Commands

Command	Description
show port-p-logi

show port-p-logi

To display information about the Fibre Channel port login, use the show port-p-logi command.

show port-p-logi [detail]

Syntax Description

detail

(Optional) Displays detailed information about the port login in list format.

Command Default

None

Command Modes

Host Fibre Channel interface (/chassis/adapter/host-fc-if )

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to display information about the port login of the host Fibre Channel interface:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # show port-p-login
PLOGI Retries PLOGI Timeout (milli-secs) 
------------- -------------------------- 
8             2000                       

Server /chassis/adapter/host-fc-if #

Related Commands

Command	Description
show port-f-logi

show port-profiles

To display information about port profiles of the adapter card, use the show port-profiles command.

show port-profiles [detail]

Syntax Description

detail

(Optional) Displays detailed information in list format.

Command Default

None

Command Modes

Adapter (/chassis/adapter)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example shows how to display the port profiles of adapter card 1:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # show port-profiles
Port Profile Name                
-------------------------------- 

Server /chassis/adapter #

Related Commands

Command	Description
set port-profile

show power-cap

To display the server power consumption statistics and the power cap policy, use the show power-cap command.

show power-cap [detail]

Syntax Description

detail

(Optional) Displays detailed information about the power consumption statistics and the power cap policy, in list format.

Command Default

None

Command Modes

Root (/server#)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

The displayed fields are described in the following table:

Name	Description
Current Consumption	The power currently being used by the server, in watts.
Maximum Consumption	The maximum number of watts consumed by the server since the last time it was rebooted.
Minimum Consumption	The minimum number of watts consumed by the server since the last time it was rebooted.
Minimum Configurable Limit	The minimum amount of power that can be specified as the peak power cap for this server, in watts.
Maximum Configurable Limit	The maximum amount of power that can be specified as the peak power cap for this server, in watts.

Additional fields are described in the following table:

Name

Description

Enable Power Capping

, the system monitors how much power is allocated to the server and takes the specified action if the server goes over its maximum allotment.

Peak Power

The maximum number of watts that can be allocated to this server. If the server requests more power than specified in this field, the system takes the action defined in the Non-Compliance Action field.

Enter a number of watts within the range defined by the Minimum Configurable Limit field and the Maximum Configurable Limit field.

Non-Compliance Action

The action the system should take if power capping is enabled and the server requests more than its peak power allotment. This can be one of the following:

—The server is forced to reduce its power consumption by any means necessary. This option is available only on some C-Series servers.
—No action is taken and the server is allowed to use more power than specified in the Peak Power field.
—The server is shut down.
—Processes running on the server are throttled to bring the total power consumption down.

Examples

This example shows how to display detailed information about the DIMMs:

server# show power-cap detail 
    Cur Consumption (W): 247
    Max Consumption (W): 286
    Min Consumption (W): 229
    Minimum Configurable Limit (W): 285
    Maximum Configurable Limit (W): 1250
    Power Cap Enabled: yes
    Peak Power: 0
    Non Compliance Action: throttle

Server#

Related Commands

Command	Description
set peak-power
set non-compliance-action

show psu (chassis)

To display information about the PSUs (power supply units), use the show psu command in chassis mode.

show psu [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the PSUs in list format.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to display information about the chassis PSUs:

server# scope chassis
server /chassis # show psu detail

Name PSU1:
    In. Power (Watts): 103
    Out. Power (Watts): 0
    Firmware : 
    Status : Present

server /chassis #

Related Commands

Command	Description
show voltage

show psu (sensor)

To display information about the status of the PSU (power supply unit) sensors, use the show psu command in sensor mode.

show psu [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the PSU sensors in list format.

Command Default

None

Command Modes

Sensor (/sensor)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to display information about the status of the PSU sensors:

server# scope sensor
server /sensor # show psu

Name                 Sensor Status        Reading    Units      Min. Warning    Max. Warning    Min. Failure    Max. Failure    
-------------------- -------------------- ---------- ---------- --------------- --------------- --------------- --------------- 
PSU1_POUT            Normal               68         Watts      N/A             652             N/A             680             
PSU1_PIN             Normal               76         Watts      N/A             652             N/A             680             
PSU1_STATUS          Normal               present                                                                               
PSU2_STATUS          Critical             absent
                                                                                
server /sensor #

Related Commands

Command	Description
show voltage

show psu-redundancy (sensor)

To display information about the status of PSU (power supply unit) redundancy, use the show psu-redundancy command in sensor mode.

show psu-redundancy [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the status of PSU redundancy in list format.

Command Default

None

Command Modes

Sensor (/sensor)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to display information about the status of PSU redundancy:

server# scope sensor
server /sensor #  show psu-redundancy detail

Name PS_RDNDNT_MODE:
    Reading: full
    Sensor Status: Normal

server /sensor #

Related Commands

Command	Description
show psu

show recv-queue

To display information about the host interface receive queue, use the show recv-queue command.

show recv-queue [detail]

Syntax Description

detail

(Optional) Displays detailed information in list format.

Command Default

None

Command Modes

Host Ethernet interface (/chassis/adapter/host-eth-if )

Host Fibre Channel interface (/chassis/adapter/host-fc-if )

VM FEX interface (/chassis/adapter/vmfex)

Command History

Release	Modification
1.2(1)	This command was introduced.
1.4(1)	This command was added to the VM FEX interface.

Examples

This example shows how to display information about the host Ethernet interface receive queue:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter/ # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # show recv-queue
Receive Queue Count Receive Queue Ring Size        
------------------- ------------------------------ 
4                   512                            

Server /chassis/adapter/host-eth-if #

Related Commands

Command	Description
scope recv-queue

show remote-syslog-severity

To display the lowest level of CIMC log messages that are sent to the remote syslog server, use the show remote-syslog-severity command.

show remote-syslog-severity [detail]

Syntax Description

detail

Displays output in list form.

Command Default

None

Command Modes

CIMC log (/cimc/log)

Command History

Release	Modification
1.4(3)	This command was introduced.

Usage Guidelines

Use this command to display the lowest level of CIMC log messages that are sent to a remote syslog server. The displayed minimum severity level can be one of the following, in decreasing order of severity:

emergency
alert
critical
error
warning
notice
informational
debug

Examples

This example displays the lowest level of CIMC log messages that are sent to a remote syslog server:

Server# scope cimc
Server /cimc # scope log
Server /cimc/log # show remote-syslog-severity
    Remote Syslog Severity: warning

Server /cimc/log #

Related Commands

Command	Description
set remote-syslog-severity

show role-group

To display the properties of an Active Directory role group, use the show role-group command.

show role-group [index] [detail]

Syntax Description

index	(Optional) The numeric identifier of the specific role group, from 1 to 5.
detail	(Optional) Displays detailed information in list form.

Command Default

None

Command Modes

LDAP (/ldap)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to display the properties of an Active Directory (AD) authorization (role) group. Five role groups are available, with index numbers 1 to 5. To display the properties of a single group, enter its index. To display the properties of all groups, omit the index.

Examples

This example shows how to display the properties of all AD role groups:

Server# scope ldap
Server /ldap # show role-group
Group  Name             Domain           Role     
------ ---------------- ---------------- -------- 
1      (n/a)            (n/a)            admin    
2      (n/a)            (n/a)            user     
3      Training         example.com      readonly 
4      (n/a)            (n/a)            (n/a)    
5      (n/a)            (n/a)            (n/a)  

Server /ldap #

Related Commands

Command	Description
scope role-group

show rss

To display information about the Receive-side Scaling (RSS) of the host Ethernet Interface, use the show rss command.

show rss [detail]

Syntax Description

detail

(Optional) Displays detailed information in list format.

Command Default

None

Command Modes

Host Ethernet interface (/chassis/adapter/host-eth-if)

VM FEX interface (/chassis/adapter/vmfex)

Command History

Release	Modification
1.2(1)	This command was introduced.
1.4(1)	This command was added to the VM FEX interface.

Examples

This example shows how to display information about RSS:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # show rss
TCP Rx Side Scaling  
-------------------- 
Enabled              

Server /chassis/adapter/host-eth-if #

Related Commands

Command	Description
scope rss
set rss

show running-firmware-images

To display running firmware information for a storage adapter, use the show running-firmware-images command.

show running-firmware-images [detail]

Syntax Description

detail

(Optional) Displays detailed information in list format.

Command Default

None

Command Modes

Storage adapter (/chassis/storageadapter)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example shows how to display running firmware information for a storage adapter in the SAS PCI slot:

server# scope chassis
server /chassis # scope storageadapter SAS
server /chassis/storageadapter # show running-firmware-images
PCI Slot SAS:
    Firmware Version: 2.120.13-1133
    BIOS Version: 3.20.00_4.11.05.00_0x0418A000
    Preboot CLI Version: 04.04-017:#%00008
    WebBIOS Version: 6.0-34-e_29-Rel
    NVDATA Version: 2.09.03-0009
    Boot Block Version: 2.02.00.00-0000
    BOOT Version: 01.250.04.219

server /chassis/storageadapter #

Related Commands

Command	Description
show storageadapter

show scsi-io

To display information about the SCSI-IO of the host Fibre Channel interface, use the show scsi-io command.

show scsi-io

This command has no arguments or keywords.

Command Default

None

Command Modes

Host Fibre Channel interface (/chassis/adapter/host-fc-if)

Command History

Release	Modification
1.2(1)	This command was introduced.

Examples

This example shows how to display the SCSI-IO of the host Fibre Channel interface:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # scope host-fc-if fc0
Server /chassis/adapter/host-fc-if # scope scsi-io
Server /chassis/adapter/host-fc-if/scsi io # show
CDB Transmit Queue Count  CDB Transmit Ring Size             
------------------------- ---------------------------------- 
1                         512              
Server /chassis/adapter/host-fc-if/scsi io #

Related Commands

Command	Description
scope scsi-io

show server

To display the configured remote syslog servers, use the show server command.

show server [detail]

Syntax Description

detail

Displays output in list form.

Command Default

None

Command Modes

CIMC log (/cimc/log)

Command History

Release	Modification
1.1(2)	This command was introduced.

Examples

This example displays the configured remote syslog servers:

Server# scope cimc
Server /cimc # scope log
Server /cimc/log # show server
Syslog Server    IP Address       Enabled  
---------------- ---------------- -------- 
1                192.0.20.3       yes       
2                0.0.0.0          no       

Server /cimc/log #

Related Commands

Command	Description
scope log

show server-management

To display the server management BIOS configuration settings, use the show server-management command.

show server-management [detail]

Syntax Description

detail

(Optional) Displays detailed server management BIOS configuration settings in list format.

Command Default

None

Command Modes

BIOS (/bios)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example displays the server management BIOS configuration details:

Server# scope bios
Server /bios # show server-management detail
Set-up parameters:
    ACPI1.0 Support: Disabled
    Assert NMI on PERR: Enabled
    Assert NMI on SERR: Enabled
    PlugNPlay BMC detection: Disabled
    Baud rate: 9.6k
    Console redirection: Disabled
    FRB2 Enable: Enabled
    Flow Control: None
    Legacy OS redirection: Disabled
    Terminal type: VT100

Server /bios #

Related Commands

Command	Description
scope server-management

show settings

To display firmware settings for a storage adapter, use the show settings command.

show settings [detail]

Syntax Description

detail

(Optional) Displays detailed information in list format.

Command Default

None

Command Modes

Storage adapter (/chassis/storageadapter)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example shows how to display firmware settings for a storage adapter in the SAS PCI slot:

server# scope chassis
server /chassis # scope storageadapter SAS
server /chassis/storageadapter # show settings
PCI Slot SAS:
    Predictive Fail Poll Interval: 300 sec
    Rebuild Rate: 50 MB/s
    Patrol Read Rate: 30 MB/s
    Consistency Check Rate: 30 MB/s
    Reconstruction Rate: 30 MB/s
    Cache Flush Interval: 4 sec
    Max Drives to Spin Up at Once: 4
    Delay Among Spinup Groups: 2 sec
    Physical Drive Coercion Mode: None
    Cluster Mode: false
    Battery Warning: true
    ECC Bucket Leak Rate: 1440 min
    Expose Enclosure Devices: true
    Maintain PD Fail History: true
    Enable Copyback on SMART: false
    Enable Copyback to SSD on SMART Error: true
    NCQ: false
    Enable Spin Down of Unconfigured Drives: true
    Enable SSD Patrol Read: false
    AutoEnhancedImport: false

server /chassis/storageadapter #

Related Commands

Command	Description
show storageadapter

show snmp

To display the SNMP configuration, use the show snmp command.

show snmp [detail]

Syntax Description

detail

(Optional) Displays detailed SNMP configuration information in list format.

Command Default

None

Command Modes

Root (server#)

Command History

Release	Modification
1.3(1)	This command was introduced.

Usage Guidelines

Use this command to display the following SNMP configuration information:

Name	Description
SNMP Port	The UDP port on which the SNMP agent receives requests.
System Contact	The system contact person responsible for the SNMP implementation.
System Location	The location of the host on which the SNMP agent runs.
SNMP Community	The SNMP v1 or v2c community name or SNMP v3 username that CIMC includes on any trap messages it sends to the SNMP host.
Enabled	Whether the SNMP agent is enabled or disabled.

Examples

This example displays the SNMP configuration details:

Server# show snmp detail
SNMP Settings:
    SNMP Port: 161
    System Contact: User Name <username@example.com> +1-408-555-1212
    System Location: San Jose, California
    SNMP Community: cimcpublic
    Enabled: yes

Server#

Related Commands

Command	Description
scope snmp

show sol

To display information about the SoL (Serial over LAN) configuration, use the show sol command.

show sol [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the SoL (serial over LAN) configuration in list format.

Command Default

None

Command Modes

Root (/server#)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to display information about the SoL configuration:

server# show sol detail

Serial Over LAN:
    Enabled: no
    Baud Rate(bps): 115200

server#

Related Commands

Command	Description
set baud-rate

show ssh

To display information about the SSH (Secure Shell) configuration on the server, use the show ssh command.

show ssh [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the SSH configuration in list format.

Command Default

None

Command Modes

Root (server#)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to display information about the SSH configuration:

server# show ssh detail

SSH Settings:
    SSH Port: 22
    Timeout: 10800
    Max Sessions: 4
    Active Sessions: 1
    Enabled: yes

server#

Related Commands

Command	Description
set enabled (ssh)
set ssh-port (ssh)

show startup-firmware-images

To display firmware images to be activated onstartup for a storage adapter, use the show startup-firmware-images command.

show startup-firmware-images [detail]

Syntax Description

detail

(Optional) Displays detailed information in list format.

Command Default

None

Command Modes

Storage adapter (/chassis/storageadapter)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example shows how to display startup firmware information for a storage adapter in the SAS PCI slot:

server# scope chassis
server /chassis # scope storageadapter SAS
server /chassis/storageadapter # show startup-firmware-images
PCI Slot SAS:
    Startup Firmware Version: N/A
    Startup BIOS Version: N/A
    Startup Preboot CLI Version: N/A
    Startup WebBIOS Version: N/A
    Startup NVDATA Version: N/A
    Startup Boot Block Version: N/A
    Startup BOOT Version: N/A

server /chassis/storageadapter #

Related Commands

Command	Description
show storageadapter

show storageadapter

To display summary information about installed storage adapters, use the show storageadapter command.

show storageadapter [slot] [detail]

Syntax Description

slot	(Optional) The PCI slot name or number of a storage adapter.
detail	(Optional) Displays detailed storage adapter information in list format.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example shows how to display information about the storage adapter in the SAS PCI slot:

Server# scope chassis
Server /chassis # show storageadapter SAS
PCI Slot SAS:
    Product Name: LSI MegaRAID SAS 9260-8i
    Serial Number: SV93404392
    Firmware Package Build: 12.12.0-0038
    Product ID: LSI Logic
    Battery Status: fully charged
    Cache Memory Size: 394 MB

Server /chassis #

Related Commands

Command	Description
scope storageadapter

show tech-support (cimc)

To display information about the configuration of the tech-support utility, use the show tech-support command in cimc mode.

show tech-support [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the configuration of the tech-support utility in list format.

Command Default

None

Command Modes

CIMC (/cimc)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to display information about the configuration of the tech-support utility:

server# scope cimc
server /cimc # show tech-support detail

Tech Support:
    TFTP Server Address: 10.20.30.211
    TFTP Path: /user/tech-support
    Progress(%): 100
    Status: COMPLETED

server /cimc #

Related Commands

Command	Description
set path (tech-support)
set tftp-ip (tech-support)

show temperature (sensor)

To display information about the status of the temperature sensors, use the show temperature command in sensor mode.

show temperature [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the status of the temperature sensors in list format.

Command Default

None

Command Modes

Sensor (/sensor)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to display information about the status of the temperature sensors:

server# scope sensor
server /sensor # show temperature

Name                      Sensor Status  Reading    Units      Min. Warning Max. Warning Min. Failure Max. Failure 
------------------------- -------------- ---------- ---------- ------------ ------------ ------------ ------------ 
IOH_TEMP_SENS             Normal         42.0       C          N/A          80.0         N/A          85.0         
P2_TEMP_SENS              Normal         43.0       C          N/A          80.0         N/A          81.0         
P1_TEMP_SENS              Normal         45.0       C          N/A          80.0         N/A          81.0         
DDR3_P2_D1_TMP            Normal         28.0       C          N/A          90.0         N/A          95.0         
DDR3_P1_A1_TMP            Normal         30.0       C          N/A          90.0         N/A          95.0         
PSU1_TEMP_1               Normal         40.0       C          N/A          60.0         N/A          65.0         
PSU2_TEMP_1               Normal         40.0       C          N/A          60.0         N/A          65.0         
FP_AMBIENT_TEMP           Normal         22.0       C          N/A          40.0         N/A          45.0         

server /sensor #

show trans-queue

To display information about the host interface transmit queue, use the show trans-queue command.

show trans-queue [detail]

Syntax Description

detail

(Optional) Displays detailed information in list format.

Command Default

None

Command Modes

Host Ethernet interface (/chassis/adapter/host-eth-if )

Host Fibre Channel interface (/chassis/adapter/host-fc-if )

VM FEX interface (/chassis/adapter/vmfex)

Command History

Release	Modification
1.2(1)	This command was introduced.
1.4(1)	This command was added to the VM FEX interface.

Examples

This example shows how to display information about the transmit queue for the host Ethernet interface:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter/ # scope host-eth-if eth0
Server /chassis/adapter/host-eth-if # show trans-queue
Transmit Queue Count Transmit Queue Ring Size        
-------------------- ------------------------------- 
1                    256                             

Server /chassis/adapter/host-eth-if #

Related Commands

Command	Description
scope trans-queue

show trap-destination

To display information about SNMP trap destinations, use the show trap-destination command.

show trap-destination [ trap-destination-number ] [ detail ]

Syntax Description

trap-destination-number	Displays information about only the specified SNMP trap destination. If the trap-destination-number variable is omitted, displays information about all SNMP trap destinations.
detail	(Optional) Displays detailed information about SNMP trap destinations in list format.

Command Default

None

Command Modes

SNMP (/snmp)

Command History

Release	Modification
1.0(1)	This command was introduced.
1.4(1)	This command was moved from the fault scope to the snmp scope.

Examples

This example shows how to display information about the SNMP trap destinations:

server# scope snmp
server /snmp # show trap-destination
 
Trap Destination IP Address       Enabled  
---------------- ---------------- -------- 
1                209.165.200.225  yes      
2                0.0.0.0          no       
3                0.0.0.0          no       
4                0.0.0.0          no       

server /snmp #

Related Commands

Command	Description
set addr (trap-destination)

show user

To display information about user profiles on the server, use the show user command.

show user [ user-number ] [ detail ]

Syntax Description

user-number	(Optional) Displays only the specified user profile. If the user-number variable is omitted, displays all user profiles.
detail	(Optional) Displays detailed information in list form.

Command Default

None

Command Modes

Root (server#)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to display information about all user profiles:

server# show user

User   Name             Role     Enabled  
------ ---------------- -------- -------- 
1      admin            admin    yes      
2      jsmith           admin    yes      
3      (n/a)            (n/a)    no       
4      (n/a)            (n/a)    no       
5      bjones           readonly yes      
6      (n/a)            (n/a)    no       
7      (n/a)            (n/a)    no       
8      (n/a)            (n/a)    no       
9      (n/a)            (n/a)    no       
10     (n/a)            (n/a)    no       
11     (n/a)            (n/a)    no       
12     (n/a)            (n/a)    no       
13     (n/a)            (n/a)    no       
14     (n/a)            (n/a)    no       
15     (n/a)            (n/a)    no       

server#

Related Commands

Command	Description
set enabled (user)
set name (user)

show user-session

To display information about current user sessions, use the show user-session command.

show user-session [ session-number ] [ detail ]

Syntax Description

session-number	Displays information about a specific session.
detail	(Optional) Displays detailed information about current user sessions in list format.

Command Default

None

Command Modes

Root (server#)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to display user session information for all current user sessions:

server# show user-session
 
ID     Name             IP Address        Type         Killable 
------ ---------------- ----------------- ------------ -------- 
4      admin            10.20.30.123      CLI          yes      
2      admin            10.20.30.185      vKVM         yes
5      read-only        10.20.30.187      CLI          no

server#

This example shows how to display user session information about a specific user session:

server# show user-session 2
 
ID     Name             IP Address        Type         Killable 
------ ---------------- ----------------- ------------ -------- 
2      admin            10.20.30.185      vKVM         yes      

server#

Related Commands

Command	Description
show user

show v3users

To display the properties of SNMPv3 users, use the show v3users command.

show v3users [user-index] [detail]

Syntax Description

user-index	(Optional) The numeric identifier of a user.
detail	(Optional) Displays detailed information in list format.

Command Default

None

Command Modes

SNMP (/snmp)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to display the configuration of SNMPv3 users. To display the configuration of a specific user, specify a user number between 1 and 15. To display the configuration of all SNMPv3 users, do not specify a user number.

Examples

This example displays the configuration for SNMPv3 user number 1:

Server# scope snmp
Server /snmp # show v3users 1
User  Add User Security Name  Security Level  
----- -------- -------------- --------------- 
1     no       (n/a)          (n/a)           
              
Server /snmp # show v3users 1 detail
User 1:
    Add User: no
    Security Name: (n/a)
    Security Level: (n/a)
    Auth Type: (n/a)
    Auth Key: ******
    Encryption: (n/a)
    Private Key: ******

Server /snmp #

Related Commands

Command	Description
scope v3users

show version

To display the version number of the running firmware, use the show version command.

show version [ detail ]

Syntax Description

detail

(Optional) Displays the version number of the running firmware in list format.

Command Default

None

Command Modes

Root (server#)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to display the version of the running firmware:

server# show version

Firmware Version     
-------------------- 
1.1(0.3)            

server#

Related Commands

Command	Description
activate (firmware)

show virtual-drive

To display virtual drive information for a storage adapter, use the show virtual-drive command.

show virtual-drive drive-number [detail]

Syntax Description

drive-number	(Optional) The drive number of the virtual drive.
detail	(Optional) Displays detailed information in list format.

Command Default

None

Command Modes

Storage adapter (/chassis/storageadapter)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example shows how to display virtual drive information for the storage adapter in the SAS PCI slot:

server# scope chassis
server /chassis # scope storageadapter SAS
server /chassis/storageadapter # show virtual-drive 1
Virtual Drive  Status               Name                     Size       RAID Level 
-------------- -------------------- ------------------------ ---------- ---------- 
0              Optimal              SLES1SP1beta5            30720 MB   RAID 0     
1              Optimal              RHEL5.5                  30720 MB   RAID 0     
2              Optimal              W2K8R2_DC                30720 MB   RAID 0     
3              Optimal              VD_3                     30720 MB   RAID 0     
4              Optimal              ESX4.0u2                 30720 MB   RAID 0     
5              Optimal              VMs                      285568 MB  RAID 0     
6              Optimal              RHEL6-35GB               35840 MB   RAID 0     
7              Optimal              OS_Ins_Test_DR           158720 MB  RAID 0     
8              Optimal                                       285568 MB  RAID 1   

server /chassis/storageadapter #

Related Commands

Command	Description
show storageadapter

show virtual-drive-count

To display the number of virtual drives for a storage adapter, use the show virtual-drive-count command.

show virtual-drive-count [detail]

Syntax Description

detail

(Optional) Displays detailed information in list format.

Command Default

None

Command Modes

Storage adapter (/chassis/storageadapter)

Command History

Release	Modification
1.3(1)	This command was introduced.

Examples

This example shows how to display the number of virtual drives on the storage adapter in the SAS PCI slot:

server# scope chassis
server /chassis # scope storageadapter SAS
server /chassis/storageadapter # show virtual-drive-count
PCI Slot SAS:
    Virtual Drive Count: 9
    Degraded Virtual Drive Count: 0
    Offline Virtual Drive Count: 0

server /chassis/storageadapter #

Related Commands

Command	Description
show storageadapter

show vmedia

To display information about the status and configuration of virtual media, use the show vmedia command.

show vmedia [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the status and configuration of virtual media in list format.

Command Default

None

Command Modes

Root (server#)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to display information about the status and configuration of virtual media:

server# show vmedia
Encryption Enabled Enabled Active Sessions 
------------------ ------- --------------- 
no                 yes     0               
server#

Related Commands

Command	Description
set encryption (vmedia)

show vmfex

To display the VM FEX properties, use the show vmfex command.

show vmfex [name] [detail]

Syntax Description

name	The name or number of the VM FEX interface.
detail	(Optional) Displays detailed information in list format.

Command Default

None

Command Modes

Adapter (/chassis/adapter)

Command History

Release	Modification
1.4(1)	This command was introduced.

Usage Guidelines

Use this command to display the virtual machine fabric extender (VM FEX) properties for all or for only the specified host interface. NIV mode must be enabled.

Examples

This example shows how to display the VM FEX properties for the host interface named pts0:

Server# scope chassis
Server /chassis # scope adapter 1
Server /chassis/adapter # show vmfex pts0
Name        MTU  Uplink Port MAC Address       CoS VLAN PXE Boot 
----------- ---- ----------- ----------------- --- ---- -------- 
pts0        1500 0           00:00:00:00:00:00 N/A N/A  disabled 

Server /chassis/adapter # show vmfex pts0 detail
Name pts0:
    MTU: 1500
    Uplink Port: 0
    MAC Address: 00:00:00:00:00:00
    CoS: N/A
    Trust Host CoS: disabled
    PCI Order: ANY
    VLAN: N/A
    VLAN Mode: N/A
    Rate Limiting: N/A
    PXE Boot: disabled
    Channel Number: 
    Port Profile: 
    Uplink Failover: 
    Uplink Failback Timeout: 

Server /chassis/adapter #

Related Commands

Command	Description
scope vmfex

show voltage (sensor)

To display information about the status of the voltage sensors, use the show voltage command in sensor mode.

show voltage [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the status of the voltage sensors in list form.

Command Default

None

Command Modes

Sensor (/sensor)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to display information about the status of the voltage sensors:

server# scope sensor
server /sensor # show voltage

Name                      Sensor Status  Reading    Units      Min. Warning Max. Warning Min. Failure Max. Failure 
------------------------- -------------- ---------- ---------- ------------ ------------ ------------ ------------ 
P3V_BAT_SCALED            Normal         3.022      V          N/A          N/A          2.798        3.088        
P12V_SCALED               Normal         12.095     V          N/A          N/A          11.623       12.331       
P5V_SCALED                Normal         5.061      V          N/A          N/A          4.844        5.157        
P3V3_SCALED               Normal         3.318      V          N/A          N/A          3.191        3.381        
P5V_STBY_SCALED           Normal         4.988      V          N/A          N/A          4.844        5.157        
PV_VCCP_CPU1              Normal         0.940      V          N/A          N/A          0.725        1.391        
PV_VCCP_CPU2              Normal         0.891      V          N/A          N/A          0.725        1.391        
P1V5_DDR3_CPU1            Normal         1.499      V          N/A          N/A          1.450        1.548        
P1V5_DDR3_CPU2            Normal         1.499      V          N/A          N/A          1.450        1.548        
P1V1_IOH                  Normal         1.087      V          N/A          N/A          1.068        1.136        
P1V8_AUX                  Normal         1.773      V          N/A          N/A          1.744        1.852        
PSU1_VOUT                 Normal         12.000     V          N/A          N/A          N/A          13.000       
PSU2_VOUT                 Normal         12.000     V          N/A          N/A          N/A          13.000

server /sensor #

start

To start the technical support process, use the start command.

start

This command has no arguments or keywords.

Command Default

None

Command Modes

Technical support (/cimc/tech-support)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to start the technical support process:

server# scope cimc

server /cimc # scope tech-support
server /cimc/tech-support # start 
Tech Support upload started.
server /cimc/tech-support #

Related Commands

Command	Description
cancel

start-initialization

To initialize a virtual drive, use the start-initialization command.

start-initialization

This command has no arguments or keywords.

Command Default

None

Command Modes

Virtual drive (/chassis/storageadapter/virtual-drive)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must be logged in as an admin to use this command.

All data on a virtual drive is lost when you initialize the drive. So, prior to running this command, you must back up the data on the virtual drive.

Examples

This example shows how to initialize virtual drive 3:

Server # scope chassis
Server /chassis # scope storageadapter SLOT-3
Server /chassis/storageadapter # scope virtual-drive 3
Server /chassis/storageadapter/virtual-drive # start-initialization
Are you sure you want to initialize virtual drive 3?
All data on the drive will be lost. Enter 'yes' to confirm. yes
Fast (0) or full (1) initialization? 0
Server /chassis/storage/adapter/virtual-drive #

start-learn-cycle

To start a learn cycle for a battery immediately, use the start-learn-cycle command.

start-learn-cycle

This command has no arguments or keywords.

Command Default

None

Command Modes

Battery Backup Unit (/chassis/storageadapter/bbu)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must be logged in as an admin to use this command.

Examples

This example shows how to initiate the learn cycles for a battery:

Server # scope chassis
Server /chassis # scope storageadapter SLOT-2
Server /chassis/storageadapter # scope bbu
Server /chassis/storageadapter/bbu # start-learn-cycle
Server /chassis/storageadapter/bbu #

terminate (user-session)

To terminate a CLI session, use the terminate command in user-session mode.

terminate

This command has no arguments or keywords.

Command Default

None

Command Modes

User session (/user-session)

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to terminate a CLI session:

server# scope user-session 3
server /user-session # terminate

Related Commands

Command	Description
show user-session

top

To return to root mode from any other mode, use the top command.

top

This command has no arguments or keywords.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
1.0(1)	This command was introduced.

Examples

This example shows how to enter root mode from log mode:

server /cimc/log # top
server#

Related Commands

Command	Description
exit

undo-prepare-for-removal

To undo the preparation for removing a physical drive, use the undo-prepare-for-removal command.

undo-prepare-for-removal

This command has no arguments or keywords.

Command Default

None

Command Modes

Physical drive (/chassis/storageadapter/physical-drive)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must be logged in as an admin to use this command.

Examples

This example shows how to re-spin physical drive 3 after preparing the drive for removal:

Server # scope chassis
Server /chassis # scope storageadapter SLOT-3
Server /chassis/storageadapter # scope physical-drive 3
Server /chassis/storageadapter/physical-drive # undo-prepare-for-removal
Server /chassis/storageadapter/physical-drive #

unmap

To unmap a CIMC-mapped vmedia volume, use the unmap command.

unmap volume-name

Syntax Description

volume-name

Name of the volume.

Command Default

None

Command Modes

vMedia (/vmedia)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

You must be logged in as an admin to use this command.

Examples

This example shows how to unmap a CIMC-mapped vmedia volume:

Server # scope vmedia
Server /vmedia # show mappings

Volume  Map-status   Drive-type     remote-share        remote-file                mount-type
------  ----------  ------------  --------------------- -------------------        ----------- 
Huu     OK           removable    http://10.104.236.99/ rhel-server-6.1-x86_6.iso      www
Rhel    OK           CD           http://10.104.236.99/ rhel-server-6.1-x86_6.iso      www           


Server /vmedia # unmap huu
Server /vmedia # show mappings

Volume  Map-status   Drive-type     remote-share        remote-file                mount-type
------  ----------  ------------  --------------------- -------------------        ----------- 
Rhel    OK           CD           http://10.104.236.99/ rhel-server-6.1-x86_6.iso      www 

Server /vmedia #

update (/bios)

To update the BIOS version from the remote server, use the update command.

update protocol IP address or hostname path

Syntax Description

protocol	The protocol to use to connect to the server. It can be one of the following: tftp ftp sftp scp http
IP address or hostname	IP address or the host name of the remote server. The format is X.X.X.X.
path	The path to the update file on the remote server.

Command Default

None

Command Modes

BIOS (/bios)

Command History

Release	Modification
1.5(1)	This command was introduced.

Usage Guidelines

This command is available only on a few C-series servers.

You must log in with admin privileges to perform this task.

Examples

This example shows how to update the BIOS version from a remote TFTP server:

Server # scope bios
Server /bios # update tftp 10.103.102.134 /sampe/file.tar.gz

BIOS update has started.
Please check the status using "show detail"

Server /bios #

update (firmware)

To update the CIMC firmware, use the update command.

update protocol ip-address file-path

Syntax Description

protocol	The protocol to use. It can be one of the following: tftp ftp sftp scp http
ip-address	The IP address of the remote server. The format is X.X.X.X.
file-path	The path to the update file on the the remote server.

Command Default

None

Command Modes

Firmware (/cimc/firmware)

Command History

Release	Modification
1.0(1)	This command was introduced.
1.5(1)	This command was modified to include new protocols.

Examples

This example shows how to update server firmware:

server# scope cimc
server /cimc # scope firmware
server /cimc/firmware # update tftp 209.165.200.225 //test/cimc66-78.bin
  <CR>  Press Enter key
Firmware update has started.
Please check the status using "show detail"
server /cimc/firmware #

Related Commands

Command	Description
show cimc
show version

update-adapter-fw

To update the adapter firmware, use the update-adapter-fw command.

update-adapter-fw tftp-ip-address path-and-filename { activate | no-activate } [pci-slot] [pci-slot]

Syntax Description

tftp-ip-address	The IP address of the remote server hosting the adapter firmware.
filename	The path and file name of the adapter firmware on the remote server.
activate	Activates the new firmware on the next boot.
no-activate	The new firmware will not be activated on the next boot.
pci-slot	The PCI slot number of the adapter card.

Command Modes

Chassis (/chassis)

Command History

Release	Modification
1.2(1)	This command was introduced.

Usage Guidelines

Use this command to download the specified adapter firmware file from the TFTP server, and then install the firmware as the backup image on one or two specified adapters or, if no adapter is specified, on all adapters. If the activate keyword is specified, the new firmware is activated on the next boot.

Examples

This example shows how to update and activate the adapter firmware on the adapter in slot 1:

Server # scope chassis
Server /chassis # update-adapter-fw 192.0.2.34 /ucs/adapters/adapter4.bin activate 1
Server /chassis #

Related Commands

Command	Description
recover-adapter-update

update-all

To update basic server component firmware, use the update-all command.

Caution

This command should only be used under the direction of Cisco TAC.

update-all

Command Default

None

Command Modes

Firmware (/chassis/firmware)

Command History

Release	Modification
1.4(5)	This command was introduced.

Examples

This example shows how to update server firmware:

server# scope chassis
server /chassis # scope firmware
server /chassis/firmware # update-all

Related Commands

Command	Description
show (firmware)

upload (certificate)

To upload a certificate, use the upload command in certificate mode.

This command has no arguments or keywords.

Command Default

None

Command Modes

Certificate (/certificate)

Command History

Release	Modification
1.0(1x)	This command was introduced.

Examples

This example shows how to upload a certificate:

server# scope certificate
server /certificate # upload
Please paste your certificate here, when finished, press CTRL+D.
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server /certificate #

Related Commands

Command	Description
generate-csr (certificate)
show certificate

Bias-Free Language

Results

Chapter: Commands

Commands

activate (firmware)

Command Default

Command Modes

Command History

Examples

Related Commands

activate-adapter-fw

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Examples

Related Commands

adapter-reset

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Examples

Related Commands

adapter-reset-defaults

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Examples

Related Commands

bios-setup-defaults

Command Default

Command Modes

Command History

Usage Guidelines

Examples

Related Commands

cancel

Command Default

Command Modes

Command History

Examples

Related Commands

cancel-initialization

Command Default

Command Modes

Command History

Usage Guidelines

Examples

carve-virtual-drive

Command Default

Command Modes

Command History

Usage Guidelines

Examples

clear (log)

Command Default

Command Modes

Command History

Examples

Related Commands

clear (sel)

Command Default

Command Modes

Command History

Examples

Related Commands

clear-cmos

Command Default

Command Modes

Command History

Examples

Related Commands

clear-foreign-config

Command Default