FlexPod Datacenter with VMware vSphere 6.7 U2, Cisco UCS 4th Generation Fabric and NetApp ONTAP 9.6

FlexPod Datacenter with VMware vSphere 6.7 U2, Cisco UCS 4^th Generation Fabric and NetApp ONTAP 9.6

Deployment Guide for FlexPod Datacenter with NetApp

ONTAP 9.6 on NetApp AFF A-Series, Cisco UCS M5 Servers with 2^nd Generation Intel Xeon Scalable Processors, and VMware vSphere 6.7 U2

Published: February 2020

NOTE: Works with document’s Advanced Properties “Last Updated” property. Click File | Properties | Advanced Properties | Custom.

In partnership with:

About the Cisco Validated Design Program

The Cisco Validated Design (CVD) program consists of systems and solutions designed, tested, and documented to facilitate faster, more reliable, and more predictable customer deployments. For more information, go to:

http://www.cisco.com/go/designzone.

ALL DESIGNS, SPECIFICATIONS, STATEMENTS, INFORMATION, AND RECOMMENDATIONS (COLLECTIVELY, "DESIGNS") IN THIS MANUAL ARE PRESENTED "AS IS," WITH ALL FAULTS.  CISCO AND ITS SUPPLIERS DISCLAIM ALL WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.  IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THE DESIGNS, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

THE DESIGNS ARE SUBJECT TO CHANGE WITHOUT NOTICE.  USERS ARE SOLELY RESPONSIBLE FOR THEIR APPLICATION OF THE DESIGNS.  THE DESIGNS DO NOT CONSTITUTE THE TECHNICAL OR OTHER PROFESSIONAL ADVICE OF CISCO, ITS SUPPLIERS OR PARTNERS.  USERS SHOULD CONSULT THEIR OWN TECHNICAL ADVISORS BEFORE IMPLEMENTING THE DESIGNS.  RESULTS MAY VARY DEPENDING ON FACTORS NOT TESTED BY CISCO.

CCDE, CCENT, Cisco Eos, Cisco Lumin, Cisco Nexus, Cisco StadiumVision, Cisco TelePresence, Cisco WebEx, the Cisco logo, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are service marks; and Access Registrar, Aironet, AsyncOS, Bringing the Meeting To You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unified Computing System (Cisco UCS), Cisco UCS B-Series Blade Servers, Cisco UCS C-Series Rack Servers, Cisco UCS S-Series Storage Servers, Cisco UCS Manager, Cisco UCS Management Software, Cisco Unified Fabric, Cisco Application Centric Infrastructure, Cisco Nexus 9000 Series, Cisco Nexus 7000 Series. Cisco Prime Data Center Network Manager, Cisco NX-OS Software, Cisco MDS Series, Cisco Unity, Collaboration Without Limitation, EtherFast, EtherSwitch, Event Center, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, iQuick Study,  LightStream, Linksys, MediaTone, MeetingPlace, MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, Network Registrar, PCNow, PIX, PowerPanels, ProConnect, ScriptShare, SenderBase, SMARTnet, Spectrum Expert, StackWise, The Fastest Way to Increase Your Internet Quotient, TransPath, WebEx, and the WebEx logo are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0809R)

© 2020 Cisco Systems, Inc. All rights reserved.

 

Table of Contents

Executive Summary. 9

Solution Overview.. 10

Introduction. 10

Audience. 10

Purpose of this Document 10

What’s New in this Release?. 10

Deployment Hardware and Software. 12

Architecture. 12

Topology. 13

Software Revisions. 13

Configuration Guidelines. 14

Physical Infrastructure. 16

Network Switch Configuration. 18

Physical Connectivity. 18

FlexPod Cisco Nexus Base. 18

Set Up Initial Configuration. 18

FlexPod Cisco Nexus Switch Configuration. 20

Enable Licenses. 20

Set Global Configurations. 20

Create VLANs. 21

Add NTP Distribution Interface. 21

Add Individual Port Descriptions for Troubleshooting and Enable UDLD for UCS Interfaces. 21

Create Port Channels. 23

Configure Port Channel Parameters. 23

Configure Virtual Port Channels. 24

Uplink into Existing Network Infrastructure. 25

Switch Testing Commands. 25

Storage Configuration. 27

NetApp All Flash FAS A320 Controllers. 27

NetApp Hardware Universe. 27

Controllers. 27

Disk Shelves. 27

NetApp ONTAP 9.6. 27

Complete Configuration Worksheet 27

Configure ONTAP Nodes. 28

Set Up Node. 31

Log into the Cluster 39

Verify Storage Failover 39

Set Auto-Revert on Cluster Management 39

Zero All Spare Disks. 40

Set Up Service Processor Network Interface. 40

Create Aggregates. 40

Remove Ports from Default Broadcast Domain. 41

Disable Flow Control on 10GbE and 100GbE ports. 41

Disable Auto-Negotiate on 100GbE Ports. 41

Disable Auto-Negotiate on Fibre Channel Ports. 42

Enable Cisco Discovery Protocol 42

Enable Link-layer Discovery Protocol on all Ethernet Ports. 42

Create Management Broadcast Domain. 43

Create NFS Broadcast Domain. 43

Create Interface Groups. 43

Change MTU on Interface Groups. 43

Create VLANs. 43

Configure Network Time Protocol 44

Configure Simple Network Management Protocol 44

Configure SNMPv1 Access. 45

Create SVM.. 45

Create Load-Sharing Mirrors of SVM Root Volume. 45

Create Block Protocol (FC) Service. 46

Configure HTTPS Access. 46

Configure NFSv3. 47

Create FlexVol Volumes. 48

Create Boot LUNs. 48

Modify Volume Efficiency. 48

Create FC LIFs. 48

Create NFS LIFs. 49

Add Infrastructure SVM Administrator 49

Configure and Test AutoSupport 50

Cisco UCS Configuration. 51

Cisco UCS Base Configuration. 51

Perform Initial Setup of Cisco UCS 6454 Fabric Interconnects for FlexPod Environments. 51

Cisco UCS Setup. 52

Log into Cisco UCS Manager 52

Upgrade Cisco UCS Manager Software to Version 4.0(4g) 53

Anonymous Reporting. 53

Configure Cisco UCS Call Home. 53

Configure Unified Ports (FCP) 54

Add Block of IP Addresses for KVM Access. 56

Synchronize Cisco UCS to NTP. 56

Add Additional DNS Server(s) 57

Add an Additional Administrative User 58

Enable Port Auto-Discovery Policy. 59

Enable Info Policy for Neighbor Discovery. 60

Edit Chassis Discovery Policy. 61

Enable Server and Uplink Ports. 61

Acknowledge Cisco UCS Chassis and FEX. 62

Create Uplink Port Channels to Cisco Nexus Switches. 63

Add UDLD to Uplink Port Channels. 66

Create an Organization. 68

Create a WWNN Pool for FC Boot (FCP) 69

Create WWPN Pools (FCP) 71

Create VSANs (FCP) 74

Enable FC Uplink VSAN Trunking (FCP) 75

Create FC Uplink Port Channels (FCP) 76

Disable Unused FC Uplink Ports (FCP) 79

Create vHBA Templates (FCP) 79

Create SAN Connectivity Policy (FCP) 81

Create MAC Address Pools. 83

Create UUID Suffix Pool 85

Create Server Pool 86

Create VLANs. 86

Modify Default Host Firmware Package. 89

Set Jumbo Frames in Cisco UCS Fabric. 90

Create Local Disk Configuration Policy (Optional) 91

Create Network Control Policy for Cisco Discovery Protocol (CDP) and Link Layer Discovery Protocol (LLDP) 93

Create Power Control Policy. 93

Create Server BIOS Policy. 95

Update the Default Maintenance Policy. 100

Create vNIC Templates. 101

Create High Traffic VMware Adapter Policy. 105

Create LAN Connectivity Policy for FC Boot (FCP) 107

Create vMedia Policy for VMware ESXi 6.7U2 ISO Install Boot 110

Create FC Boot Policy (FCP) 112

Create Service Profile Template (FCP) 117

Configure Storage Provisioning. 118

Configure Networking. 118

Configure SAN Connectivity. 119

Configure Zoning. 120

Configure vNIC/HBA Placement 120

Configure vMedia Policy. 120

Configure Server Boot Order 121

Configure Maintenance Policy. 121

Configure Server Assignment 122

Configure Operational Policies. 123

Create vMedia-Enabled Service Profile Template. 124

Create Service Profiles. 125

Add More Servers to FlexPod Unit 125

Gather Necessary Information. 126

SAN Switch Configuration. 127

Physical Connectivity. 127

FlexPod Cisco MDS Base. 127

Cisco MDS 9132T A. 127

FlexPod Cisco MDS Switch Configuration. 130

Enable Licenses. 130

Add Second NTP Server 130

Configure Individual Ports. 130

Create VSANs. 132

Create Device Aliases. 133

Create Zones and Zoneset 133

Storage Configuration – Boot LUNs. 135

ONTAP Boot Storage Setup. 135

Create igroups. 135

Map Boot LUNs to igroups. 135

VMware vSphere 6.7U2 Setup. 136

VMware ESXi 6.7U2. 136

Download ESXi 6.7U2 from VMware. 136

Log into Cisco UCS 6454 Fabric Interconnect 136

Set Up VMware ESXi Installation. 137

Install ESXi 137

Set Up Management Networking for ESXi Hosts. 138

Reset VMware ESXi Host VMkernel Port vmk0 MAC Address (Optional) 140

Install VMware Drivers for the Cisco Virtual Interface Card (VIC) and ESXi Host 140

Log into the First VMware ESXi Host by Using VMware Host Client 141

Set Up VMkernel Ports and Virtual Switch. 142

Mount Required Datastores. 144

Configure NTP on First ESXi Host 146

Configure ESXi Host Swap. 147

VMware vCenter 6.7U2. 148

Build the VMware vCenter Server Appliance. 148

Adjust vCenter CPU Settings. 159

Setup VMware vCenter Server 161

Add AD User Authentication to vCenter (Optional) 165

FlexPod VMware vSphere Distributed Switch (vDS) 166

Configure the VMware vDS in vCenter 167

Add and Configure a VMware ESXi Host in vCenter 171

Add the ESXi Host to vCenter 171

Set Up VMkernel Ports and Virtual Switch. 172

Mount Required Datastores. 175

Configure NTP on ESXi Host 175

Configure ESXi Host Swap. 176

Check ESXi Host Fibre Channel Pathing. 177

Add the ESXi Host(s) to the VMware Virtual Distributed Switch. 178

Add the vMotion VMkernel Port to the ESXi Host 179

VMware ESXi 6.7U2 TPM Attestation. 180

FlexPod Management Tools Setup. 182

Cisco UCS Manager Plug-in for VMware vSphere Web Client 182

Cisco UCS Manager Plug-in Installation. 182

FlexPod UCS Domain Registration. 184

Register the Proactive High Availability Provider for Cisco UCS (Optional) 185

Use the Cisco UCS vCenter Plugin. 187

NetApp Virtual Storage Console 9.6 Deployment Procedure. 190

Virtual Storage Console 9.6 Pre-installation Considerations. 190

The requirements for deploying VSC are listed here. 190

Install Virtual Storage Console 9.6. 190

Download the NetApp NFS VAAI Plug-In. 193

Install the NetApp NFS VAAI Plug-In. 193

Enable the VASA Provider 194

Discover and Add Storage Resources. 195

Optimal Storage Settings for ESXi Hosts. 197

Virtual Storage Console 9.6 Provisioning Datastores. 198

NetApp SnapCenter 4.2. 205

Deploy NetApp SnapCenter 205

SnapCenter Server Requirements. 206

SnapCenter 4.2 License Requirements. 207

SnapCenter Server 207

SnapCenter Plug-In for VMware vSphere. 208

Support for Virtualized Databases and File Systems. 208

SnapCenter Installation. 208

SnapCenter Configuration. 208

Install SnapCenter Plug-In for VMware. 210

Host and Privilege Requirements for the NetApp Data Broker 210

Download and Deploy the NetApp Data Broker OVA (Open Virtual Appliance) 211

Create a Virtual Appliance Credential for Migrating Backups. 216

Register the SnapCenter Plug-in for VMware vSphere with SnapCenter Server 217

Register the SnapCenter Plug-in for VMware vSphere with VMware Vcenter 217

SnapCenter Plug-in for VMware vSphere in VCenter Server 218

Add Storage Systems (SVM) 219

View Virtual Machine Backups and Restore from vCenter by Using SnapCenter Plug-In. 227

View Backups. 227

Restore from vCenter by Using SnapCenter Plug-In. 230

Provision Virtual Volumes (VVols) 234

Verify NDMP Vserver Scope Mode. 234

OnCommand API Services for ONTAP VASA Provider 235

Create the Storage Capability Profile. 238

Provision VVOL from Virtual Storage Console. 239

Create Virtual Machine with Assigned VM Storage Policy. 242

VSC VVOl Dashboard and Reports. 243

Active IQ Unified Manager 9.6. 244

Configure Active IQ Unified Manager 250

Add Storage to Active IQ Unified Manager 251

Sample Tenant Provisioning. 254

Provision a Sample Application Tenant 254

Appendix. 256

FlexPod iSCSI Addition. 256

Cisco Nexus Switch Configuration. 256

NetApp Storage Configuration – Part 1. 256

Cisco UCS iSCSI Configuration. 258

NetApp Storage Configuration – Part 2. 280

VMware vSphere Configuration. 281

ESXi Dump Collector Setup for iSCSI-Booted Hosts. 296

Create a FlexPod ESXi Custom ISO using VMware vCenter 296

FlexPod Backups. 301

Cisco UCS Backup. 301

Cisco Nexus and MDS Backups. 303

VMware VCSA Backup. 304

About the Authors. 306

Acknowledgements. 306

 

 

Cisco Validated Designs (CVDs) include systems and solutions that are designed, tested, and documented to facilitate and improve customer deployments. These designs incorporate a wide range of technologies and products into a portfolio of solutions that have been developed to address the business needs of customers. Cisco and NetApp have partnered to deliver FlexPod, which serves as the foundation for a variety of workloads and enables efficient architectural designs that are based on customer requirements. A FlexPod solution is a validated approach for deploying Cisco and NetApp technologies as a shared cloud infrastructure.

This document describes the Cisco and NetApp® FlexPod Datacenter with NetApp ONTAP 9.6, Cisco UCS Manager unified software release 4.0(4) with 2^nd Generation Intel Xeon Scalable Processors and VMware vSphere 6.7 U2. Cisco UCS Manager (UCSM) 4.0(4) provides consolidated support of all current Cisco UCS Fabric Interconnect models (6200, 6300, 6324 (Cisco UCS Mini)), 6454,2200/2300/2400 series IOM, Cisco UCS B-Series, and Cisco UCS C-Series.  FlexPod Datacenter with NetApp ONTAP 9.6, Cisco UCS unified software release 4.0(4), and VMware vSphere 6.7 U2 is a predesigned, best-practice data center architecture built on the Cisco Unified Computing System (Cisco UCS), the Cisco Nexus® 9000 family of switches, MDS 9000 multilayer fabric switches, and NetApp AFF A-Series storage arrays running ONTAP® 9.6 storage OS.

Introduction

The current industry trend in datacenter design is towards shared infrastructures. By using virtualization along with pre-validated IT platforms, enterprise customers have embarked on the journey to the cloud by moving away from application silos and toward shared infrastructure that can be quickly deployed, thereby increasing agility and reducing costs. Cisco and NetApp have partnered to deliver FlexPod, which uses best of breed storage, server and network components to serve as the foundation for a variety of workloads, enabling efficient architectural designs that can be quickly and confidently deployed.

Audience

The audience for this document includes, but is not limited to; sales engineers, field consultants, professional services, IT managers, partner engineers, and customers who want to take advantage of an infrastructure built to deliver IT efficiency and enable IT innovation.

Purpose of this Document

This document provides a step-by-step configuration and implementation guide for the FlexPod Datacenter with Cisco UCS Fabric Interconnects, NetApp AFF storage, Cisco MDS, and Cisco Nexus 9000 solution.

What’s New in this Release?

The following design elements distinguish this version of FlexPod from previous FlexPod models:

·       Support for the Cisco UCS 4.0(4) unified software release, Cisco UCS B200-M5 and C220-M5 servers with 2^nd Generation Intel Xeon Scalable Processors, and Cisco 1400 Series Virtual Interface Cards (VICs)

·       Support for the latest Cisco UCS 6454 Fabric Interconnect

·       Support for the latest Cisco UCS 2408 Fabric Extender

·       Support for the NetApp AFF A320 Storage Controller

·       Support for the latest release of NetApp ONTAP® 9.6

·       Support for NetApp Virtual Storage Console (VSC) 9.6

·       Support for NetApp SnapCenter 4.2 and NetApp Data Broker 1.0

·       Support for NetApp Active IQ Unified Manager 9.6

·       Fibre channel, NFS, iSCSI (appendix) storage design

·       Validation of VMware vSphere 6.7 U2

·       Unified Extensible Firmware Interface (UEFI) Secure Boot of VMware ESXi 6.7 U2

·       Trusted Platform Module (TPM) 2.0 Attestation of UEFI Secure Boot of VMware ESXi 6.7 U2

·       100 Gigabit per second Ethernet Connectivity

·       32 Gigabit per second Fibre Channel Connectivity

Architecture

FlexPod is a defined set of hardware and software that serves as an integrated foundation for both virtualized and non-virtualized solutions. VMware vSphere® built on FlexPod includes NetApp All Flash FAS storage, Cisco Nexus® networking, Cisco MDS storage networking, the Cisco Unified Computing System (Cisco UCS®), and VMware vSphere software in a single package. The design is flexible enough that the networking, computing, and storage can fit in one data center rack or be deployed according to a customer's data center design. Port density enables the networking components to accommodate multiple configurations of this kind.

One benefit of the FlexPod architecture is the ability to customize or "flex" the environment to suit a customer's requirements. A FlexPod can easily be scaled as requirements and demand change. The unit can be scaled both up (adding resources to a FlexPod unit) and out (adding more FlexPod units). The reference architecture detailed in this document highlights the resiliency, cost benefit, and ease of deployment of a Fibre Channel and IP-based storage solution. A storage system capable of serving multiple protocols across a single interface allows for customer choice and investment protection because it truly is a wire-once architecture.

Figure 1 shows the VMware vSphere built on FlexPod components and the network connections for a configuration with the Cisco UCS 6454 Fabric Interconnects. This design has port-channeled 25 Gb Ethernet connections between the Cisco UCS 5108 Blade Chassis and the Cisco UCS Fabric Interconnects via the Cisco UCS 2408 Fabric Extenders, port-channeled 25 Gb Ethernet connections between the C-Series rackmounts and the Cisco UCS Fabric Interconnects, and 100 Gb Ethernet connections between the Cisco UCS Fabric Interconnect and Cisco Nexus 9000, and between Cisco Nexus 9000 and NetApp AFF A320 storage array. This infrastructure option expanded with Cisco MDS switches sitting between the Cisco UCS Fabric Interconnect and the NetApp AFF A320 to provide FC-booted hosts with 32 Gb FC block-level access to shared storage.  The reference architecture reinforces the "wire-once" strategy, because as additional storage is added to the architecture, no re-cabling is required from the hosts to the Cisco UCS fabric interconnect.

Topology

The reference 100Gb based hardware configuration includes:

·       Two Cisco Nexus 9336c-FX2 switches

·       Two Cisco UCS 6454 fabric interconnects

·       Two Cisco MDS 9132T multilayer fabric switches

·       One NetApp AFF 320 (HA pair) running ONTAP 9.6 with internal NVMe SSD disks

Software Revisions

Table 1   lists the software revisions for this solution.

Table 1    Software Revisions

Configuration Guidelines

This document explains how to configure a fully redundant, highly available configuration for a FlexPod unit with ONTAP storage. Therefore, reference is made to which component is being configured with each step, either 01 or 02 or A and B. For example, node01 and node02 are used to identify the two NetApp storage controllers that are provisioned with this document, and Cisco Nexus A or Cisco Nexus B identifies the pair of Cisco Nexus switches that are configured. The Cisco UCS Fabric Interconnects are similarly configured. Additionally, this document details the steps for provisioning multiple Cisco UCS hosts, and these examples are identified as: VM-Host-Infra-01, VM-Host-Infra-02 to represent infrastructure hosts deployed to each of the fabric interconnects in this document. Finally, to indicate that you should include information pertinent to your environment in a given step, <text> appears as part of the command structure. See the following example for the network port vlan create command:

Usage:

network port vlan create ?

 [-node] <nodename>                  Node

 { [-vlan-name] {<netport>|<ifgrp>}  VLAN Name

 |  -port {<netport>|<ifgrp>}        Associated Network Port

 [-vlan-id] <integer> }              Network Switch VLAN Identifier

Example:

network port vlan create -node <node01> -vlan-name a0a-<vlan id>

This document is intended to enable you to fully configure the customer environment. In this process, various steps require you to insert customer-specific naming conventions, IP addresses, and VLAN schemes, as well as to record appropriate MAC addresses. Table 2  describes the VLANs necessary for deployment as outlined in this guide.

Table 2    Necessary VLANs

Table 3   lists the VMs necessary for deployment as outlined in this document.

Table 3    Virtual Machines

Physical Infrastructure

FlexPod Cabling

The information in this section is provided as a reference for cabling the physical equipment in a FlexPod environment. To simplify cabling requirements, a cabling diagram was used.

The cabling diagram in this section contains details for the prescribed and supported configuration of the NetApp AFF 320 running NetApp ONTAP® 9.6.

This document assumes that out-of-band management ports are plugged into an existing management infrastructure at the deployment site. These interfaces will be used in various configuration steps.

The NetApp storage controller and disk shelves should be connected according to best practices for the specific storage controller and disk shelves. For disk shelf cabling, refer to NetApp Support.

Figure 2 details the cable connections used in the validation lab for the FlexPod topology based on the Cisco UCS 6454 fabric interconnect.  Two 32Gb uplinks connect as port-channels to each Cisco UCS Fabric Interconnect from the MDS switches, and a total of four 32Gb links connect the MDS switches to the NetApp AFF controllers.  Also, 100Gb links connect the Cisco UCS Fabric Interconnects to the Cisco Nexus Switches and the NetApp AFF controllers to the Cisco Nexus Switches. Additional 1Gb management connections will be needed for an out-of-band network switch that sits apart from the FlexPod infrastructure.  Each Cisco UCS fabric interconnect and Cisco Nexus switch is connected to the out-of-band network switch, and each AFF controller has two connections to the out-of-band network switch. Layer 3 network connectivity is required between the Out-of-Band (OOB) and In-Band (IB) Management Subnets.

This section provides a detailed procedure for configuring the Cisco Nexus 9000s for use in a FlexPod environment. Follow these steps precisely because failure to do so could result in an improper configuration.

Physical Connectivity

Follow the physical connectivity guidelines for FlexPod as explained in FlexPod Cabling.

FlexPod Cisco Nexus Base

The following procedures describe how to configure the Cisco Nexus switches for use in a base FlexPod environment.  This procedure assumes the use of Cisco Nexus 9000 7.0(3)I7(7), the Cisco suggested Nexus switch release at the time of this validation.

 

Set Up Initial Configuration

Cisco Nexus A

To set up the initial configuration for the Cisco Nexus A switch on <nexus-A-hostname>, follow these steps:

1.     Configure the switch.

2.     Review the configuration summary before enabling the configuration.

Cisco Nexus B

To set up the initial configuration for the Cisco Nexus B switch on <nexus-B-hostname>, follow these steps:

1.     Configure the switch.

2.     Review the configuration summary before enabling the configuration.

Use this configuration and save it? (yes/no) [y]: Enter

FlexPod Cisco Nexus Switch Configuration

Enable Licenses

Cisco Nexus A and Cisco Nexus B

To license the Cisco Nexus switches, follow these steps:

1.     Log in as admin.

2.     Run the following commands:

Set Global Configurations

Cisco Nexus A and Cisco Nexus B

To set global configurations, follow this step on both switches:

1.     Run the following commands to set global configurations:

Create VLANs

Cisco Nexus A and Cisco Nexus B

To create the necessary virtual local area networks (VLANs), follow this step on both switches:

1.     From the global configuration mode, run the following commands:

Add NTP Distribution Interface

Cisco Nexus A

1.     From the global configuration mode, run the following commands:

Cisco Nexus B

1.     From the global configuration mode, run the following commands:

Add Individual Port Descriptions for Troubleshooting and Enable UDLD for UCS Interfaces

Cisco Nexus A

To add individual port descriptions for troubleshooting activity and verification for switch A, follow this step:

1.     From the global configuration mode, run the following commands:

Cisco Nexus B

To add individual port descriptions for troubleshooting activity and verification for switch B and to enable aggressive UDLD on copper interfaces connected to Cisco UCS systems, follow this step:

1.     From the global configuration mode, run the following commands:

Create Port Channels

Cisco Nexus A and Cisco Nexus B

To create the necessary port channels between devices, follow this step on both switches:

1.     From the global configuration mode, run the following commands:

Configure Port Channel Parameters

Cisco Nexus A and Cisco Nexus B

To configure port channel parameters, follow this step on both switches:

1.     From the global configuration mode, run the following commands:

Configure Virtual Port Channels

Cisco Nexus A

To configure virtual port channels (vPCs) for switch A, follow this step:

1.     From the global configuration mode, run the following commands:

Cisco Nexus B

To configure vPCs for switch B, follow this step:

1.     From the global configuration mode, run the following commands:

Uplink into Existing Network Infrastructure

Depending on the available network infrastructure, several methods and features can be used to uplink the FlexPod environment. If an existing Cisco Nexus environment is present, we recommend using vPCs to uplink the Cisco Nexus switches included in the FlexPod environment into the infrastructure. The previously described procedures can be used to create an uplink vPC to the existing environment. Make sure to run copy run start to save the configuration on each switch after the configuration is completed.

Switch Testing Commands

The following commands can be used to check for correct switch configuration:

NetApp All Flash FAS A320 Controllers

See the following section (NetApp Hardware Universe) for planning the physical location of the storage systems:

·       Site Preparation

·       System Connectivity Requirements

·       Circuit Breaker, Power Outlet Balancing, System Cabinet Power Cord Plugs, and Console Pinout Requirements

·       AFF Series Systems

NetApp Hardware Universe

The NetApp Hardware Universe (HWU) application provides supported hardware and software components for any specific ONTAP version. It also provides configuration information for all the NetApp storage appliances currently supported by ONTAP software and a table of component compatibilities.

To confirm that the hardware and software components that you would like to use are supported with the version of ONTAP that you plan to install, follow these steps at the NetApp Support site.

1.     Access the HWU application to view the System Configuration guides. Click the Platforms menu to view the compatibility between different version of the ONTAP software and the NetApp storage appliances with your desired specifications.

2.     Alternatively, to compare components by storage appliance, click Compare Storage Systems.

Controllers

Follow the physical installation procedures for the controllers found in the AFF A320 Series product documentation at the NetApp Support site.

Disk Shelves

NetApp storage systems support a wide variety of disk shelves and disk drives. The complete list of disk shelves that are supported by the AFF A320 is available at the NetApp Support site.

When using SAS disk shelves with NetApp storage controllers, refer to the SAS cabling rules section in the AFF and FAS System Documentation Center for proper cabling guidelines.

NetApp ONTAP 9.6

Complete Configuration Worksheet

Before running the setup script, complete the Cluster setup worksheet in the ONTAP 9 Documentation Center. You must have access to the NetApp Support site to open the cluster setup worksheet.

Configure ONTAP Nodes

Before running the setup script, review the configuration worksheets in the Software setup section of the ONTAP 9 Documentation Center to learn about configuring ONTAP. Table 4  lists the information needed to configure two ONTAP nodes. Customize the cluster-detail values with the information applicable to your deployment.

Table 4    ONTAP Software Installation Prerequisites

Configure Node 01

To configure node 01, follow these steps:

1.     Connect to the storage system console port. You should see a Loader-A prompt. However, if the storage system is in a reboot loop, press Ctrl-C to exit the autoboot loop when the following message displays:

2.     Allow the system to boot up.

3.     Press Ctrl-C when prompted.

4.     To install new software, select option 7.

5.     Enter y to perform an upgrade.

6.     Select e0M for the network port you want to use for the download.

7.     Enter y to reboot now.

8.     Enter the IP address, netmask, and default gateway for e0M.

9.     Enter the URL where the software can be found.

10.  Press Enter for the user name, indicating no user name.

11.  Enter y to set the newly installed software as the default to be used for subsequent reboots.

12.  Enter y to reboot the node.

13.  Press Ctrl-C when the following message displays:

14.  Select option 4 for Clean Configuration and Initialize All Disks.

15.  Enter y to zero disks, reset config, and install a new file system.

16.  Enter y to erase all the data on the disks.

Configure Node 02

To configure node 02, follow these steps:

1.     Connect to the storage system console port. You should see a Loader-A prompt. However, if the storage system is in a reboot loop, press Ctrl-C to exit the autoboot loop when the following message displays:

2.     Allow the system to boot up.

3.     Press Ctrl-C when prompted.

4.     To install new software, select option 7.

5.     Enter y to perform an upgrade.

6.     Select e0M for the network port you want to use for the download.

7.     Enter y to reboot now.

8.     Enter the IP address, netmask, and default gateway for e0M.

9.     Enter the URL where the software can be found.

10.  Press Enter for the user name, indicating no user name.

11.  Enter y to set the newly installed software as the default to be used for subsequent reboots.

12.  Enter y to reboot the node.

13.  Press Ctrl-C when you see this message:

14.  Select option 4 for Clean Configuration and Initialize All Disks.

15.  Enter y to zero disks, reset config, and install a new file system.

16.  Enter y to erase all the data on the disks.

Set Up Node

From a console port program attached to the storage controller A (node 01) console port, run the node setup script. This script appears when ONTAP 9.6 boots on the node for the first time.

1.     Follow the prompts to set up node 01.

2.     To complete cluster setup, open a web browser and navigate to https://<node01-mgmt-ip>.

Table 5    Cluster Create in ONTAP Prerequisites

3.     Click Guided Setup on the Welcome screen.

 

4.     In the Cluster screen, follow these steps:

a.     Enter the cluster and node names.

b.     Select the cluster configuration.

c.     Enter and confirm the password.

d.     (Optional) Enter the cluster base and feature licenses.

5.     Click Submit.

6.     In the network page, complete the following sections:

a.     Cluster Management

§  Enter the IP address, netmask, gateway, and port details.

b.     Node Management

§  Enter the node management IP addresses and port details for all the nodes.

c.     Service Processor Management

§  Enter the IP addresses for all nodes.

d.     DNS Details

§  Enter the DNS domain names and server address.

e.     NTP Details

§  Enter the primary and alternate NTP server.

7.     Click Submit.

8.     In the Support page, configure the AutoSupport and Event Notifications sections.

9.     Click Submit.

10.  In the Storage page, review the configuration details.

11.  Skip this step if you want to configure it later. Otherwise, click Submit and Continue.

12.  In the SVM Tab, you can create your own SVM, or you can skip this step.

13.  Click Skip this Step.

14.  In the Summary page, review the configuration details if needed and click Manage Your Cluster.

Log into the Cluster

To log into the cluster, follow these steps:

1.     Open an SSH connection to either the cluster IP or the host name.

2.     Log in to the admin user with the password you provided earlier.

Verify Storage Failover

To confirm that storage failover is enabled, run the following commands for a failover pair:

1.     Verify the status of the storage failover.

2.     Enable failover on one of the two nodes if it was not completed during the installation.

3.     Verify the HA status for a two-node cluster.

4.     Continue with step 5 if high availability is not configured.

5.     Only enable HA mode for two-node clusters. Do not run this command for clusters with more than two nodes because it causes problems with failover.

6.     Verify that hardware assist is correctly configured.

Set Auto-Revert on Cluster Management

To set the auto-revert parameter on the cluster management interface, follow this step:

Run the following command:

Zero All Spare Disks

To zero all spare disks in the cluster, run the following command:

Set Up Service Processor Network Interface

To assign a static IPv4 address to the service processor on each node, run the following commands:

Create Aggregates

An aggregate containing the root volume is created during the ONTAP setup process. To create additional aggregates, determine the aggregate name, the node on which to create it, and the number of disks it should contain.

To create new aggregates, run the following commands:

Remove Ports from Default Broadcast Domain

By default, all network ports are included in the default broadcast domain. Network ports used for data services (for example, e5a, e5b, and so on) should be removed from the default broadcast domain, leaving just the management network port (e0M). To perform this task, run the following commands:

Disable Flow Control on 10GbE and 100GbE ports

NetApp recommends disabling flow control on all the 10/40/100GbE and UTA2 ports that are connected to external devices. To disable flow control, follow these steps:

1.     Run the following commands to configure node 01:

2.     Run the following commands to configure node 02:

Disable Auto-Negotiate on 100GbE Ports

To disable auto-negotiate on the 100GbE ports, follow these steps:

1.     Run the following command to configure the ports on node 01:

2.     Run the following command to configure the ports on node 02:

Disable Auto-Negotiate on Fibre Channel Ports

In accordance with the best practices for Fibre Channel host ports, disable auto-negotiate on each FCP adapter in each controller node.

1.     Disable each Fibre Channel adapter in the controllers with the fcp adapter modify command.

2.     Set the desired speed on the adapter and return it to the online state.

Enable Cisco Discovery Protocol

To enable the Cisco Discovery Protocol (CDP) on the NetApp storage controllers, run the following command to enable CDP on ONTAP:

Enable Link-layer Discovery Protocol on all Ethernet Ports

Enable the exchange of Link-layer Discovery Protocol (LLDP) neighbor information between the storage and network switches with the following step:

1.     Enable LLDP on all ports of all nodes in the cluster.

Create Management Broadcast Domain

If the management interfaces are required to be on a separate VLAN, create a new broadcast domain for those interfaces.

Create NFS Broadcast Domain

To create an NFS data broadcast domain with an MTU of 9000, run the following commands to create a broadcast domain for NFS in ONTAP:

Create Interface Groups

To create the LACP interface groups for the 100GbE data interfaces, run the following commands:

Change MTU on Interface Groups

Change the MTU size on the base interface-group ports before creating the VLAN ports.

Create VLANs

To create VLANs, follow these steps:

1.     Create the management VLAN ports and add them to the management broadcast domain.

2.     Create the NFS VLAN ports and add them to the Infra_NFS broadcast domain.

Configure Network Time Protocol

To configure time synchronization on the cluster, follow these steps:

1.     Set the time zone for the cluster.

2.     Set the date for the cluster.

3.     Configure the Network Time Protocol (NTP) servers for the cluster.

Configure Simple Network Management Protocol

To configure the Simple Network Management Protocol (SNMP), follow these steps:

1.     Configure basic SNMP information, such as the location and contact. When polled, this information is visible as the sysLocation and sysContact variables in SNMP.

2.     Configure SNMP traps to send to remote hosts, such as a DFM server or another fault management system.

Configure SNMPv1 Access

To configure SNMPv1 access, set the shared, secret plain-text password (called a community).

Create SVM

To create an infrastructure SVM, follow these steps:

1.     Run the vserver create command.

2.     Remove the unused data protocols from the SVM: CIFS, iSCSI, and NVMe.

3.     Add the two data aggregates to the Infra-SVM aggregate list for the NetApp VSC.

4.     Enable and run the NFS protocol in the Infra-SVM.

5.     Turn on the SVM vstorage parameter for the NetApp NFS VAAI plug-in.

Create Load-Sharing Mirrors of SVM Root Volume

To create a load-sharing mirror of an SVM root volume, follow these steps:

1.     Create a volume to be the load-sharing mirror of the infrastructure SVM root volume on each node.

2.     Create a job schedule to update the root volume mirror relationships every 15 minutes.

3.     Create the mirroring relationships.

4.     Initialize the mirroring relationship.

Create Block Protocol (FC) Service

Run the following command to create the FCP service on each SVM. This command also starts the FCP service and sets the WWN for the SVM.

Configure HTTPS Access

To configure secure access to the storage controller, follow these steps:

1.     Increase the privilege level to access the certificate commands.

2.     Generally, a self-signed certificate is already in place. Verify the certificate and obtain parameters (for example, the <serial-number>) by running the following command:

3.     For each SVM shown, the certificate common name should match the DNS FQDN of the SVM. Delete the two default certificates and replace them with either self-signed certificates or certificates from a certificate authority (CA). To delete the default certificates, run the following commands:

4.     To generate and install self-signed certificates, run the following commands as one-time commands. Generate a server certificate for the Infra-SVM and the cluster SVM. Use TAB completion to aid in the completion of these commands.

5.     To obtain the values for the parameters required in step 5 (<cert-ca> and <cert-serial>), run the security certificate show command.

6.     Enable each certificate that was just created by using the –server-enabled true and –client-enabled false parameters. Use TAB completion to aid in the completion of these commands.

7.     Disable HTTP cluster management access.

8.     Change back to the normal admin privilege level and verify that the system logs are available in a web browser.

 

Configure NFSv3

To configure NFSv3 on the SVM, follow these steps:

1.     Create a new rule for the infrastructure NFS subnet in the default export policy.

2.     Assign the FlexPod export policy to the infrastructure SVM root volume.

Create FlexVol Volumes

The following information is required to create a NetApp FlexVol^® volume:

·       The volume name

·       The volume size

·       The aggregate on which the volume exists

To create a FlexVol volume, run the following commands:

Create Boot LUNs

To create three boot LUNs, run the following commands:

Modify Volume Efficiency

On NetApp All Flash FAS systems, deduplication is enabled by default. To disable the efficiency policy on the infra_swap volume, follow this step:

Create FC LIFs

Run the following commands to create four FC LIFs (two on each node):

Create NFS LIFs

To create NFS LIFs, run the following commands:

Add Infrastructure SVM Administrator

To add the infrastructure SVM administrator and SVM administration LIF in the out-of-band management network, follow these steps:

1.     Run the following commands:

2.     Create a default route that enables the SVM management interface to reach the outside world.

3.     Set a password for the SVM vsadmin user and unlock the user.

Configure and Test AutoSupport

NetApp AutoSupport® sends support summary information to NetApp through HTTPS. To configure AutoSupport, run the following command:

Test the AutoSupport configuration by sending a message from all nodes of the cluster:

Cisco UCS Base Configuration

This FlexPod deployment explains the configuration steps for the Cisco UCS 6454 Fabric Interconnects (FI) in a design that will support Fibre Channel SAN boot.

Perform Initial Setup of Cisco UCS 6454 Fabric Interconnects for FlexPod Environments

This section provides the detailed procedures for configuring the Cisco Unified Computing System (Cisco UCS) for use in a FlexPod environment. The steps are necessary to provision the Cisco UCS B-Series and C-Series servers and should be followed precisely to avoid improper configuration.

Cisco UCS Fabric Interconnect A

To configure the Cisco UCS for use in a FlexPod environment, follow these steps:

1.     Connect to the console port on the first Cisco UCS fabric interconnect.

2.     Wait for the login prompt for UCS Fabric Interconnect A before proceeding to the next section.

Cisco UCS Fabric Interconnect B

To configure the Cisco UCS for use in a FlexPod environment, follow these steps:

1.     Connect to the console port on the second Cisco UCS fabric interconnect.

2.     Wait for the login prompt for UCS Fabric Interconnect B before proceeding to the next section.

Cisco UCS Setup

Log into Cisco UCS Manager

To log into the Cisco Unified Computing System (UCS) environment, follow these steps:

1.     Open a web browser and navigate to the Cisco UCS fabric interconnect cluster address.

2.     Click the Launch UCS Manager link to launch Cisco UCS Manager.

3.     If prompted to accept security certificates, accept as necessary.

4.     When prompted, enter admin as the user name and enter the administrative password.

5.     Click Login to log in to Cisco UCS Manager.

Upgrade Cisco UCS Manager Software to Version 4.0(4g)

This document assumes the use of Cisco UCS 4.0(4g). To upgrade the Cisco UCS Manager software and the Cisco UCS Fabric Interconnect software to version 4.0(4g), refer to Cisco UCS Manager Install and Upgrade Guides.

Anonymous Reporting

To enable anonymous reporting, follow this step:

1.     In the Anonymous Reporting window, select whether to send anonymous data to Cisco for improving future products. If you select Yes, enter the IP address of your SMTP Server.  Click OK.

Configure Cisco UCS Call Home

It is highly recommended by Cisco to configure Call Home in Cisco UCS Manager.  Configuring Call Home will accelerate resolution of support cases.  To configure Call Home, follow these steps:

1.     In Cisco UCS Manager, click Admin.

2.     Select All > Communication Management > Call Home.

3.     Change the State to On.

4.     Fill in all the fields according to your Management preferences and click Save Changes and OK to complete configuring Call Home.

Configure Unified Ports (FCP)

Fibre Channel port configurations differ between the 6454, 6332-16UP and the 6248UP Fabric Interconnects.  All Fabric Interconnects have a slider mechanism within the Cisco UCS Manager GUI interface, but the fibre channel port selection options for the 6454 are from the first 8 ports starting from the first port and configured in increments of 4 ports from the left. For the 6332-16UP the port selection options are from the first 16 ports starting from the first port, and configured in increments of the first 6, 12, or all 16 of the unified ports.  With the 6248UP, the port selection options will start from the right of the 32 fixed ports, or the right of the 16 ports of the expansion module, going down in contiguous increments of 2. The remainder of this section shows configuration of the 6454. Modify as necessary for the 6332-16UP or 6248UP.

To enable the fibre channel ports, follow these steps for the 6454:

1.     In Cisco UCS Manager, click Equipment.

2.     Select Equipment > Fabric Interconnects > Fabric Interconnect B (subordinate).

3.     Select Configure Unified Ports.

4.     Click Yes on the pop-up window warning that changes to the fixed module will require a reboot of the fabric interconnect and changes to the expansion module will require a reboot of that module.

5.     Within the Configured Fixed Ports pop-up window move the gray slider bar from the left to the right to select either 4 or 8 ports to be set as FC Uplinks.

6.     Click OK, then click Yes, then click OK to continue.

7.     Select Equipment > Fabric Interconnects > Fabric Interconnect A (primary).

8.     Select Configure Unified Ports.

9.     Click Yes on the pop-up window warning that changes to the fixed module will require a reboot of the fabric interconnect and changes to the expansion module will require a reboot of that module.

10.  Within the Configured Fixed Ports pop-up window move the gray slider bar from the left to the right to select either 4 or 8 ports to be set as FC Uplinks.

11.  Click OK, then click Yes, then OK to continue.

12.  Wait for both Fabric Interconnects to reboot.

13.  Log back into Cisco UCS Manager.

Add Block of IP Addresses for KVM Access

To create a block of IP addresses for in band server Keyboard, Video, Mouse (KVM) access in the Cisco UCS environment, follow these steps:

1.     In Cisco UCS Manager, click LAN.

2.     Expand Pools > root > IP Pools.

3.     Right-click IP Pool ext-mgmt and select Create Block of IPv4 Addresses.

4.     Enter the starting IP address of the block, number of IP addresses required, and the subnet mask and gateway information. Optionally, enter the Primary and Secondary DNS server addresses.

5.     Click OK to create the block.

6.     Click OK in the confirmation message.

Synchronize Cisco UCS to NTP

To synchronize the Cisco UCS environment to the NTP servers in the Nexus switches, follow these steps:

1.     In Cisco UCS Manager, click Admin.

2.     Expand All > Time Zone Management.

3.     Select Timezone.

4.     In the Properties pane, select the appropriate time zone in the Timezone menu.

5.     Click Save Changes, and then click OK.

6.     Click Add NTP Server.

7.     Enter <nexus-A-mgmt0-ip> and click OK. Click OK on the confirmation.

8.     Click Add NTP Server.

9.     Enter <nexus-B-mgmt0-ip> and click OK. Click OK.

Add Additional DNS Server(s)

To add one or more additional DNS servers to the UCS environment, follow these steps:

1.     In Cisco UCS Manager, click Admin.

2.     Expand All > Communications Management.

3.     Select DNS Management.

4.     In the Properties pane, select Specify DNS Server.

5.     Enter the IP address of the additional DNS server.

6.     Click OK and then click OK again. Repeat this process for any additional DNS servers.

Add an Additional Administrative User

To add an additional locally authenticated Administrative user (flexadmin) to the Cisco UCS environment in case issues arise with the admin user, follow these steps:

1.     In Cisco UCS Manager, click Admin.

2.     Expand User Management > User Services > Locally Authenticated Users.

3.     Right-click Locally Authenticated Users and select Create User.

4.     In the Create User fields it is only necessary to fill in the Login ID, Password, and Confirm Password fields. Fill in the Create User fields according to your local security policy.

5.     Leave the Account Status field set to Active.

6.     Set Account Expires according to your local security policy.

7.     Under Roles, select admin.

8.     Leave Password Required selected for the SSH Type field.

9.     Click OK and then click OK again to complete adding the user.

Enable Port Auto-Discovery Policy

Setting the port auto-discovery policy enables automatic discovery of Cisco UCS B-Series chassis server ports. To modify the port auto-discovery policy, follow these steps:

1.     In Cisco UCS Manager, click Equipment, select All > Equipment in the Navigation Pane, and select the Policies tab on the right.

2.     Under Port Auto-Discovery Policy, set Auto Configure Server Port to Enabled.

3.     Click Save Changes and then OK.

Enable Info Policy for Neighbor Discovery

Enabling the info policy enables Fabric Interconnect neighbor information to be displayed. To modify the info policy, follow these steps:

1.     In Cisco UCS Manager, click Equipment, select All > Equipment in the Navigation Pane, and select the Policies tab on the right.

2.     Under Global Policies, scroll down to Info Policy and select Enabled for Action.

3.     Click Save Changes and then OK.

4.     Under Equipment, select Fabric Interconnect A (primary). On the right, select the Neighbors tab. CDP information is shown under the LAN tab and LLDP information is shown under the LLDP tab.

Edit Chassis Discovery Policy

Setting the discovery policy simplifies the addition of Cisco UCS B-Series chassis and of additional fabric extenders for further Cisco UCS C-Series connectivity. To modify the chassis discovery policy, follow these steps:

1.     In Cisco UCS Manager, click Equipment and select the Policies tab on the right.

2.     Under Global Policies, set the Chassis/FEX Discovery Policy to match the minimum number of ports that are cabled between the chassis or fabric extenders (FEXes) and the fabric interconnects.

3.     On the 6454 Fabric Interconnects, the Link Grouping Preference is automatically set to Port Channel and is greyed out.  On a 6300 Series or 6200 Series Fabric Interconnect, set the Link Grouping Preference to Port Channel. If Backplane Speed Preference appears, leave it set at 40G.

4.     If any changes have been made, click Save Changes and then click OK.

Enable Server and Uplink Ports

To enable and verify server and uplink ports, follow these steps:

1.     In Cisco UCS Manager, click Equipment.

2.     Expand Equipment > Fabric Interconnects > Fabric Interconnect A (primary) > Fixed Module.

3.     Expand and select Ethernet Ports.

4.     Verify that all ports connected to UCS chassis are configured as Server ports and have a status of Up.

5.     Select the ports that are connected to Cisco FEXes and direct connect Cisco UCS C-Series servers, right-click them, and select Configure as Server Port.

6.     Click Yes to confirm server ports and click OK.

7.     Verify that the ports connected to the chassis, C-series servers and Cisco FEX are now configured as server ports.

8.     Select the ports that are connected to the Cisco Nexus switches, right-click them, and select Configure as Uplink Port.

9.     Click Yes to confirm uplink ports and click OK.

10.  Select Equipment > Fabric Interconnects > Fabric Interconnect B (subordinate) > Fixed Module.

11.  Expand and select Ethernet Ports.

12.  Verify that all ports connected to UCS chassis are configured as Server ports and have a status of Up.

13.  Select the ports that are connected to Cisco FEXes and direct connect C-series servers, right-click them, and select Configure as Server Port.

14.  Click Yes to confirm server ports and click OK.

15.  Verify that the ports connected to the chassis, C-series servers and Cisco FEX are now configured as server ports.

16.  Select the ports that are connected to the Cisco Nexus switches, right-click them, and select Configure as Uplink Port.

17.  Click Yes to confirm the uplink ports and click OK.

Acknowledge Cisco UCS Chassis and FEX

To acknowledge all Cisco UCS chassis and any external FEX modules, follow these steps:

1.     In Cisco UCS Manager, click Equipment.

2.     Expand Chassis and select each chassis that is listed.

3.     Right-click each chassis and select Acknowledge Chassis.

4.     Click Yes and then click OK to complete acknowledging the chassis.

5.     If Nexus FEXes are part of the configuration, expand Rack Mounts and FEX.

6.     Right-click each FEX that is listed and select Acknowledge FEX.

7.     Click Yes and then click OK to complete acknowledging the FEX.

Create Uplink Port Channels to Cisco Nexus Switches

To configure the necessary port channels out of the Cisco UCS environment, follow these steps:

1.     In Cisco UCS Manager, click LAN.

2.     Under LAN > LAN Cloud, expand the Fabric A tree.

3.     Right-click Port Channels under Fabric A.

4.     Select Create Port Channel.

5.     Enter 153 as the unique ID of the port channel.

6.     Enter Po153-Nexus as the name of the port channel.

7.     Click Next.

8.     Select the uplink ports connected to the Nexus switches to be added to the port channel.

9.     Click >> to add the ports to the port channel.

10.  Click Finish to create the port channel.

11.  Click OK.

12.  In the navigation pane, under LAN > LAN Cloud > Fabric A > Port Channels, select Port-Channel 153. Select 100 Gbps for the Admin Speed.

13.  Click Save Changes and OK. After a few minutes, verify that the Overall Status is Up and the Operational Speed is correct.

14.  In the navigation pane, under LAN > LAN Cloud, expand the fabric B tree.

15.  Right-click Port Channels under Fabric B.

16.  Select Create Port Channel.

17.  Enter 154 as the unique ID of the port channel.

18.  Enter Po154-Nexus as the name of the port channel.

19.  Click Next.

20.  Select the ports connected to the Nexus switches to be added to the port channel:

21.  Click >> to add the ports to the port channel.

22.  Click Finish to create the port channel.

23.  Click OK.

24.  In the navigation pane, under LAN > LAN Cloud > Fabric B > Port Channels, select Port-Channel 154. Select 100 Gbps for the Admin Speed.

25.  Click Save Changes and OK. After a few minutes, verify that the Overall Status is Up and the Operational Speed is correct.

26.  In the navigation pane, under LAN > LAN Cloud > Fabric A > Port Channels, expand Port-Channel 153. Under Port-Channel 153, select Eth Interface 1/53. In the center pane under Properties, enter a User Label to indicate the port connectivity, such as <nexus-a-hostname>:1/5. Click Save Changes and OK. Repeat this process for the remaining three uplink ports.

Add UDLD to Uplink Port Channels

To configure the unidirectional link detection (UDLD) on the Uplink Port Channels to the Nexus switches for fibre optic connections, follow these steps:

1.     In Cisco UCS Manager, click LAN.

2.     Expand Policies > LAN Cloud > UDLD Link Policy.

3.     Right-click UDLD Link Policy and select Create UDLD Link Policy.

4.     Name the Policy UDLD-Normal and select Enabled for the Admin State and Normal for the Mode.

5.     Click OK, then OK again to complete creating the policy.

6.     Expand Policies > LAN Cloud > Link Profile.

7.     Right-click Link Profile and select Create Link Profile.

8.     Name the Profile UDLD-Normal and select the UDLD-Normal Link Policy created above.

9.     Click OK, then click OK again to complete creating the profile.

10.  In the navigation pane, under LAN > LAN Cloud > Fabric A > Port Channels, expand Port-Channel 153. Select the first Eth Interface under Port-Channel 153. From the drop-down list, select the UDLD-Normal Link Profile created above, click Save Changes and OK. Repeat this process for each Eth Interface under Port-Channel 153 and for each Eth Interface under Port-Channel 154 on Fabric B.

Create an Organization

To this point in the UCS deployment, all items have been deployed at the root level in Cisco UCS Manager. To allow this UCS to be shared among different projects, UCS Organizations can be created.  In this validation, the organization for this FlexPod deployment in NA-FlexPod. To create an organization for this FlexPod deployment, follow these steps:

1.     In Cisco UCS Manager, click Servers.

2.     In the Navigation Pane, expand Servers > Service Profiles.

3.     Right-click root under Service Profiles and select Create Organization.

4.     Provide a name for the Organization to indicate this FlexPod deployment and optionally provide a Description.

5.     Click OK, then click OK again to complete creating the organization.

Create a WWNN Pool for FC Boot (FCP)

To configure the necessary WWNN pool for the Cisco UCS environment, follow these steps on Cisco UCS Manager.

1.     Select SAN.

2.     Select Pools > root.

3.     Right-click WWNN Pools under the root organization.

4.     Select Create WWNN Pool to create the WWNN pool.

5.     Enter WWNN-Pool for the name of the WWNN pool.

6.     Optional: Enter a description for the WWNN pool.

7.     Select Sequential for Assignment Order.

8.     Click Next.

9.     Click Add.

10.  Modify the From field as necessary for the UCS Environment

11.  Specify a size of the WWNN block sufficient to support the available server resources.

12.  Click OK.

13.  Click Finish and click OK to complete creating the WWNN pool.

Create WWPN Pools (FCP)

To configure the necessary WWPN pools for the Cisco UCS environment, follow these steps:

1.     In Cisco UCS Manager, click SAN.

2.     Select Pools > root.

3.     Right-click WWPN Pools under the root organization.

4.     Select Create WWPN Pool to create the WWPN pool.

5.     Enter WWPN-Pool-A as the name of the WWPN pool.

6.     Optional: Enter a description for the WWPN pool.

7.     Select Sequential for Assignment Order.

8.     Click Next.

9.     Click Add.

10.  Specify a starting WWPN.

11.  Specify a size for the WWPN pool that is sufficient to support the available blade or server resources remembering that servers could have multiple vHBAs and unassociated service profiles could be created.

12.  Click OK.

13.  Click Finish.

14.  In the confirmation message, click OK.

15.  Right-click WWPN Pools under the root organization.

16.  Select Create WWPN Pool to create the WWPN pool.

17.  Enter WWPN-Pool-B as the name of the WWPN pool.

18.  Optional: Enter a description for the WWPN pool.

19.  Select Sequential for Assignment Order.

20.  Click Next.

21.  Click Add.

22.  Specify a starting WWPN.

23.  Specify a size for the WWPN address pool that is sufficient to support the available blade or server resources remembering that servers could have multiple vHBAs and unassociated service profiles could be created.

24.  Click OK.

25.  Click Finish.

26.  In the confirmation message, click OK.

Create VSANs (FCP)

To configure the necessary virtual storage area networks (VSANs) for the FlexPod Organization in the Cisco UCS environment, follow these steps:

1.     In Cisco UCS Manager, click SAN.

2.     Select SAN > SAN Cloud.

3.     Right-click VSANs.

4.     Select Create VSAN.

5.     Enter VSAN-A as the name of the VSAN to be used for Fabric A.

6.     Leave FC Zoning set at Disabled.

7.     Select Fabric A.

8.     Enter a unique VSAN ID and a corresponding FCoE VLAN ID that matches the configuration in the MDS switch for Fabric A.  It is recommended to use the same ID for both parameters and to use something other than 1.

9.     Click OK and then click OK again.

10.  Under SAN Cloud, right-click VSANs.

11.  Select Create VSAN.

12.  Enter VSAN-B as the name of the VSAN to be used for Fabric B.

13.  Leave FC Zoning set at Disabled.

14.  Select Fabric B.

15.  Enter a unique VSAN ID and a corresponding FCoE VLAN ID that matches the configuration in the MDS switch for Fabric B.  It is recommended use the same ID for both parameters and to use something other than 1.

16.  Click OK and then click OK again.

Enable FC Uplink VSAN Trunking (FCP)

To enable VSAN trunking on the FC Uplinks in the Cisco UCS environment, follow these steps:

1.     In Cisco UCS Manager, click SAN.

2.     Expand SAN > SAN Cloud.

3.     Select Fabric A and in the Actions pane select Enable FC Uplink Trunking.

4.     Click Yes on the Confirmation and Warning.

5.     Click OK.

6.     Select Fabric B and in the Actions pane select Enable FC Uplink Trunking.

7.     Click Yes on the Confirmation and Warning.

8.     Click OK.

Create FC Uplink Port Channels (FCP)

To create the FC Uplink Port Channels and assign the appropriate VSANs to them for the Cisco UCS environment, follow these steps:

1.     In Cisco UCS Manager, click SAN.

2.     Select SAN > SAN Cloud.

3.     Expand Fabric A and select FC Port Channels.

4.     Right-click FC Port Channels and select Create FC Port Channel.

5.     Set a unique ID for the port channel and provide a unique name for the port channel.

6.     Click Next.

7.     Select the appropriate Port Channel Admin Speed.

8.     Select the ports connected to Cisco MDS A and use >> to add them to the port channel.

9.     Click Finish to complete creating the port channel.

10.  Click OK the confirmation.

11.  Under FC Port-Channels, select the newly created port channel.

12.  In the right pane, view the drop-down list to select NA-VSAN-A.

13.  Click Save Changes to assign the VSAN.

14.  Click OK.

15.  On the left under FC Port Channels, expand FC Port-Channel 11. Under FC Port-Channel 11 select FC Interface 1/1. Enter a User Label to indicate the connectivity on the MDS 9132T switch, such as <mds-A-hostname>:fc1/5. Click Save Changes and OK. Repeat this process for FC Interface 1/2.

16.  Expand Fabric B and select FC Port Channels.

17.  Right-click FC Port Channels and select Create FC Port Channel.

18.  Set a unique ID for the port channel and provide a unique name for the port channel.

19.  Click Next.

20.  Select the ports connected to Cisco MDS B and use >> to add them to the port channel.

21.  Click Finish to complete creating the port channel.

22.  Click OK on the confirmation.

23.  Under FC Port-Channels, select the newly created port channel.

24.  In the right pane, use the drop-down to select VSAN-B.

25.  Click Save Changes to assign the VSAN.

26.  Click OK.

27.  On the left under FC Port Channels, expand FC Port-Channel 12. Under FC Port-Channel 12 select FC Interface 1/1. Enter a User Label to indicate the connectivity on the MDS 9132T switch, such as <mds-B-hostname>:fc1/5. Click Save Changes and OK. Repeat this process for FC Interface 1/2.

Disable Unused FC Uplink Ports (FCP)

When Unified Ports were configured earlier in this procedure, on the Cisco UCS 6454 FI and the Cisco UCS 6332-16UP FI, FC ports were configured in groups. Because of this group configuration, some FC ports are unused and need to be disabled to prevent alerts. To disable the unused FC ports 3 and 4 on the Cisco UCS 6454 FIs, follow these steps:

1.     In Cisco UCS Manager, click Equipment.

2.     In the Navigation Pane, expand Equipment > Fabric Interconnects > Fabric Interconnect A > Fixed Module > FC Ports.

3.     Select FC Port 3 and FC Port 4. Right-click and select Disable.

4.     Click Yes and OK to complete disabling the unused FC ports.

5.     In the Navigation Pane, expand Equipment > Fabric Interconnects > Fabric Interconnect B > Fixed Module > FC Ports.

6.     Select FC Port 3 and FC Port 4. Right-click and select Disable.

7.     Click Yes and OK to complete disabling the unused FC ports.

Create vHBA Templates (FCP)

To create the necessary virtual host bus adapter (vHBA) templates for the Cisco UCS environment within the FlexPod organization, follow these steps:

1.     In Cisco UCS Manager, click SAN.

2.     Expand Policies > root > Sub-Organizations > NA-FlexPod.

3.     Right-click vHBA Templates under the FlexPod Organization.

4.     Select Create vHBA Template.

5.     Enter FCP-vHBA-A as the vHBA template name.

6.     Keep Fabric A selected.

7.     Leave Redundancy Type set to No Redundancy.

8.     Select VSAN-A.

9.     Leave Initial Template as the Template Type.

10.   Select WWPN-Pool-A as the WWPN Pool.

11.  Click OK to create the vHBA template.

12.  Click OK.

13.  Right-click vHBA Templates under the FlexPod Organization.

14.  Select Create vHBA Template.

15.  Enter FCP-vHBA-B as the vHBA template name.

16.  Select Fabric B as the Fabric ID.

17.  Leave Redundancy Type set to No Redundancy.

18.  Select VSAN-B.

19.  Leave Initial Template as the Template Type.

20.  Select WWPN-Pool-B as the WWPN Pool.

21.  Click OK to create the vHBA template.

22.  Click OK.

Create SAN Connectivity Policy (FCP)

To configure the necessary Infrastructure SAN Connectivity Policy within the FlexPod organization, follow these steps:

1.     In Cisco UCS Manager, click SAN.

2.     Select SAN > Policies > root > Sub-Organizations > NA-FlexPod.

3.     Right-click SAN Connectivity Policies under the FlexPod Organization.

4.     Select Create SAN Connectivity Policy.

5.     Enter FC-Boot as the name of the policy.

6.     Select the previously created WWNN-Pool for the WWNN Assignment.

7.     Click the Add button at the bottom to add a vHBA.

8.     In the Create vHBA dialog box, enter FCP-Fabric-A as the name of the vHBA.

9.     Select the Use vHBA Template checkbox.

10.  In the vHBA Template list, select FCP-vHBA-A.

11.  In the Adapter Policy list, select VMWare.

12.  Click OK.

13.  Click the Add button at the bottom to add a second vHBA.

14.  In the Create vHBA dialog box, enter FCP-Fabric-B as the name of the vHBA.

15.  Select the Use vHBA Template checkbox.

16.  In the vHBA Template list, select FCP-vHBA-B.

17.  In the Adapter Policy list, select VMWare.

18.  Click OK.

19.  Click OK to create the SAN Connectivity Policy.

20.  Click OK to confirm creation.

Create MAC Address Pools

To configure the necessary MAC address pools for the Cisco UCS environment, follow these steps:

1.     In Cisco UCS Manager, click LAN.

2.     Select Pools > root.

3.     Right-click MAC Pools under the root organization.

4.     Select Create MAC Pool to create the MAC address pool.

5.     Enter MAC-Pool-A as the name of the MAC pool.

6.     Optional: Enter a description for the MAC pool.

7.     Select Sequential as the option for Assignment Order.

8.     Click Next.

9.     Click Add.

10.  Specify a starting MAC address.

11.  Specify a size for the MAC address pool that is sufficient to support the available blade or server resources remembering that a server may contain multiple vNICs and that multiple unassociated Service Profiles can be created.

12.  Click OK.

13.  Click Finish.

14.  In the confirmation message, click OK.

15.  Right-click MAC Pools under the root organization.

16.  Select Create MAC Pool to create the MAC address pool.

17.  Enter MAC-Pool-B as the name of the MAC pool.

18.  Optional: Enter a description for the MAC pool.

19.  Select Sequential as the option for Assignment Order.

20.  Click Next.

21.  Click Add.

22.  Specify a starting MAC address.

23.  Specify a size for the MAC address pool that is sufficient to support the available blade or server resources remembering that a server may contain multiple vNICs and that multiple unassociated Service Profiles can be created.

24.  Click OK.

25.  Click Finish.

26.  In the confirmation message, click OK.

Create UUID Suffix Pool

To configure the necessary universally unique identifier (UUID) suffix pool for the Cisco UCS environment, follow these steps:

1.     In Cisco UCS Manager, click Servers.

2.     Select Pools > root.

3.     Right-click UUID Suffix Pools.

4.     Select Create UUID Suffix Pool.

5.     Enter UUID-Pool as the name of the UUID suffix pool.

6.     Optional: Enter a description for the UUID suffix pool.

7.     Keep the prefix at the derived option.

8.     Select Sequential for the Assignment Order.

9.     Click Next.

10.  Click Add to add a block of UUIDs.

11.  Keep the From field at the default setting.

12.  Specify a size for the UUID block that is sufficient to support the available blade or server resources.

13.  Click OK.

14.  Click Finish.

15.  Click OK.

Create Server Pool

To configure the necessary server pool for the Cisco UCS environment in the FlexPod Organization, follow these steps:

1.     In Cisco UCS Manager, click Servers.

2.     Select and expand Pools > root > Sub-Organizations > NA-FlexPod.

3.     Right-click Server Pools under the FlexPod Organization.

4.     Select Create Server Pool.

5.     Enter Infra-Pool as the name of the server pool.

6.     Optional: Enter a description for the server pool.

7.     Click Next.

8.     Select three (or more) servers to be used for the VMware management cluster and click >> to add them to the Infra-Pool server pool.

9.     Click Finish.

10.  Click OK.

Create VLANs

To configure the necessary virtual local area networks (VLANs) for the Cisco UCS environment, follow these steps:

1.     In Cisco UCS Manager, click LAN.

2.     Expand LAN > LAN Cloud.

3.     Right-click VLANs.

4.     Select Create VLANs.

5.     Enter Native-VLAN as the name of the VLAN to be used as the native VLAN.

6.     Keep the Common/Global option selected for the scope of the VLAN.

7.     Enter the native VLAN ID.

8.     Keep the Sharing Type as None.

9.     Click OK and then click OK again.

10.  Expand the list of VLANs in the navigation pane, right-click the newly created Native-VLAN and select Set as Native VLAN.

11.  Click Yes and then click OK.

12.  Right-click VLANs.

13.  Select Create VLANs

14.  Enter IB-MGMT as the name of the VLAN to be used for management traffic.

15.  Keep the Common/Global option selected for the scope of the VLAN.

16.  Enter the In-Band management VLAN ID.

17.  Keep the Sharing Type as None.

18.  Click OK, and then click OK again.

19.  Right-click VLANs.

20.  Select Create VLANs.

21.  Enter Infra-NFS as the name of the VLAN to be used for NFS.

22.  Keep the Common/Global option selected for the scope of the VLAN.

23.  Enter the Infrastructure NFS VLAN ID.

24.  Keep the Sharing Type as None.

25.  Click OK, and then click OK again.

26.  Right-click VLANs.

27.  Select Create VLANs.

28.  Enter vMotion as the name of the VLAN to be used for vMotion.

29.  Keep the Common/Global option selected for the scope of the VLAN.

30.  Enter the vMotion VLAN ID.

31.  Keep the Sharing Type as None.

32.  Click OK and then click OK again.

33.  Select Create VLANs.

34.  Enter VM-Traffic as the name of the VLAN to be used for VM Traffic.

35.  Keep the Common/Global option selected for the scope of the VLAN.

36.  Enter the VM-Traffic VLAN ID.

37.  Keep the Sharing Type as None.

38.  Click OK and then click OK again.

Modify Default Host Firmware Package

Firmware management policies allow the administrator to select the corresponding packages for a given server configuration. These policies often include packages for adapter, BIOS, board controller, FC adapters, host bus adapter (HBA) option ROM, and storage controller properties.

To modify the default firmware management policy in the Cisco UCS environment, follow these steps:

1.     In Cisco UCS Manager, click Servers.

2.     Expand Policies > root.

3.     Expand Host Firmware Packages.

4.     Select default.

5.     In the Actions pane, select Modify Package Versions.

6.     Select version 4.0(4g) for both the Blade and Rack Packages.

7.     Click OK, then click OK again to modify the host firmware package.

Set Jumbo Frames in Cisco UCS Fabric

Jumbo Frames are used in FlexPod for the NFS and iSCSI storage protocols. The normal best practice in FlexPod has been to set the MTU of the Best Effort QoS System Class in Cisco UCS Manager to 9216 for Jumbo Frames. In the Cisco UCS 6454 Fabric Interconnect the MTU for the Best Effort QoS System Class is fixed at normal and cannot be changed.  With this setting of normal in the 6454, Jumbo Frames can pass through the Cisco UCS fabric without being dropped. The screenshot below is from Cisco UCS Manager on a 6454 Fabric Interconnect, where the MTU for the Best Effort class is not settable.  To configure jumbo frames in the Cisco UCS fabric in a 6300 or 6200 series Fabric Interconnect, follow these steps:

1.     In Cisco UCS Manager, click LAN.

2.     Expand LAN > LAN Cloud > QoS System Class.

3.     In the right pane, click the General tab.

4.     On the Best Effort row, enter 9216 in the box under the MTU column.

5.     Click Save Changes.

6.     Click OK.

Create Local Disk Configuration Policy (Optional)

A local disk configuration specifying no local disks for the Cisco UCS environment is necessary if the servers in the environment do not have a local disk.

To create a local disk configuration policy, follow these steps:

1.     In Cisco UCS Manager, click Servers.

2.     Expand Policies > root.

3.     Right-click Local Disk Config Policies.

4.     Select Create Local Disk Configuration Policy.

5.     Enter SAN-Boot as the local disk configuration policy name.

6.     Change the mode to No Local Storage.

7.     Click OK to create the local disk configuration policy.

8.     Click OK.

Create Network Control Policy for Cisco Discovery Protocol (CDP) and Link Layer Discovery Protocol (LLDP)

To create a network control policy that enables CDP and LLDP on server virtual network controller (vNIC) ports, follow these steps:

1.     In Cisco UCS Manager, click LAN.

2.     Expand Policies > root.

3.     Right-click Network Control Policies.

4.     Select Create Network Control Policy.

5.     Enter Enable-CDP-LLDP as the policy name.

6.     For CDP, select the Enabled option.

7.     For LLDP, scroll down and select Enabled for both Transmit and Receive.

8.     Click OK to create the network control policy.

9.     Click OK.

Create Power Control Policy

To create a power control policy for the Cisco UCS environment, follow these steps:

1.     In Cisco UCS Manager, click Servers.

2.     Expand Policies > root.

3.     Right-click Power Control Policies.

4.     Select Create Power Control Policy.

5.     Enter No-Power-Cap as the power control policy name.

6.     Change the power capping setting to No Cap.

7.     Click OK to create the power control policy.

8.     Click OK.

 Create Server Pool Qualification Policy (Optional)

To create an optional server pool qualification policy for the Cisco UCS environment, follow these steps:

1.     In Cisco UCS Manager, click Servers.

2.     Expand Policies > root.

3.     Right-click Server Pool Policy Qualifications.

4.     Select Create Server Pool Policy Qualification.

5.     Name the policy UCS-B200M5.

6.     Select Create Server PID Qualifications.

7.     Select UCSB-B200-M5 from the PID drop-down list.

8.     Click OK

9.     Optionally select additional qualifications to refine server selection parameters for the server pool.

10.  Click OK to create the policy then OK for the confirmation.

Create Server BIOS Policy

To create a server BIOS policy for VMware ESXi hosts within the FlexPod organization, follow these steps:

1.     In Cisco UCS Manager, click Servers.

2.     Expand Policies > root > Sub-Organizations > NA-FlexPod.

3.     Right-click BIOS Policies under FlexPod Organization.

4.     Select Create BIOS Policy.

5.     Enter VM-Host as the BIOS policy name.

6.     Click OK, then click OK again to create the BIOS Policy.

7.     Under the FlexPod Organization, expand BIOS Policies and select the newly created BIOS Policy. Set the following within the Main tab of the Policy:

a.     CDN Control -> Enabled

b.     Quiet Boot -> Disabled

8.     Click the Advanced tab, leaving the Processor tab selected within the Advanced tab. Set the following within the Processor tab:

a.     DRAM Clock Throttling -> Performance

b.     Frequency Floor Override -> Enabled

9.     Scroll down to the remaining Processor options and select:

a.     Processor C State -> Disabled

b.     Processor C1E -> Disabled

c.     Processor C3 Report -> Disabled

d.     Processor C7 Report -> Disabled

e.     Energy Performance -> Performance

10.  Click the RAS Memory tab, and select:

a.     LV DDR Mode -> Performance Mode

11.  Click Save Changes.

12.  Click OK.

Update the Default Maintenance Policy

To update the default Maintenance Policy to either require user acknowledgement before server boot when service profiles change or to make the changes on the next server reboot, follow these steps:

1.     In Cisco UCS Manager, click Servers.

2.     Expand Policies > root.

3.     Select Maintenance Policies > default.

4.     Change the Reboot Policy to User Ack.

5.     Select “On Next Boot” to delegate maintenance windows to server administrators.

6.     Click Save Changes.

7.     Click OK to accept the changes.

Create vNIC Templates

To create multiple virtual network interface card (vNIC) templates within the FlexPod organization, follow these steps. A total of 4 vNIC Templates will be created. Two of the vNIC templates (Infra-A and Infra-B) will be created for vNICs to connect to VMware ESXi vSwitch0. vSwitch0 will have port groups for the IB-MGMT, Infra-NFS, vMotion, and VM-Traffic VLANs.  The third and fourth vNIC templates (Infra-vDS-A and Infra-vDS-B) will be created for vNICs to connect to the VMware Virtual Distributed Switch (vDS). The vDS will have port groups for the IB-MGMT, vMotion, and VM-Traffic VLANs. The vMotion VLAN is being placed on both vSwitch0 and the vDS so that the vMotion VMkernel port can initially be created on vSwitch0 then migrated to the vDS to allow QoS marking of vMotion packets to occur within the vDS if QoS policies need to be applied to vMotion in the future. The IB-MGMT VLAN is being placed on both vSwitch0 and the vDS so that management virtual machines other than vCenter can be placed on the vDS. The VM-Traffic VLAN is being placed on both vSwitch0 and the vDS so that it will be allowed on vSwitch0 in case the customer chooses not to implement the vDS on the management ESXi hosts.

Create Infrastructure vNIC Templates

To create the infrastructure vNIC templates, follow these steps:

1.     In Cisco UCS Manager, click LAN.

2.     Expand Policies > root > Sub-Organizations > NA-FlexPod.

3.     Under the FlexPod Organization, right-click vNIC Templates.

4.     Select Create vNIC Template.

5.     Enter vSwitch0-A as the vNIC template name.

6.     Keep Fabric A selected.

7.     Do not select the Enable Failover checkbox.

8.     Select Primary Template for Redundancy Type.

9.     Leave the Peer Redundancy Template set to <not set>.

10.  Under Target, make sure that only the Adapter checkbox is selected.

11.  Select Updating Template as the Template Type.

12.  Under VLANs, select the checkboxes for IB-MGMT, Infra-NFS, vMotion, VM-Traffic, and Native-VLAN VLANs.

13.  Set Native-VLAN as the native VLAN.

14.  Select vNIC Name for the CDN Source.

15.  For MTU, enter 9000.

16.  In the MAC Pool list, select MAC-Pool-A.

17.  In the Network Control Policy list, select Enable-CDP-LLDP.

 

18.  Click OK to create the vNIC template.

19.  Click OK.

20.  Under the FlexPod organization, right-click vNIC Templates.

21.  Select Create vNIC Template.

22.  Enter vSwitch0-B as the vNIC template name.

23.  Select Fabric B.

24.  Do not select the Enable Failover checkbox.

25.  Set Redundancy Type to Secondary Template.

26.  Select vSwitch0-A for the Peer Redundancy Template.

27.  In the MAC Pool list, select MAC-Pool-B.

28.  Click OK to create the vNIC template.

29.  Click OK.

30.  Under the FlexPod Organization, right-click vNIC Templates.

31.  Select Create vNIC Template.

32.  Enter vDS0-A as the vNIC template name.

33.  Keep Fabric A selected.

34.  Do not select the Enable Failover checkbox.

35.  Select Primary Template for Redundancy Type.

36.  Leave the Peer Redundancy Template set to <not set>.

37.  Under Target, make sure that only the Adapter checkbox is selected.

38.  Select Updating Template as the Template Type.

39.  Under VLANs, select the checkboxes for IB-MGMT, vMotion, VM-Traffic, and Native-VLAN VLANs.

40.  Set Native-VLAN as the native VLAN.

41.  Select vNIC Name for the CDN Source.

42.  For MTU, enter 9000.

43.  In the MAC Pool list, select MAC-Pool-A.

44.  In the Network Control Policy list, select Enable-CDP-LLDP.

 

45.  Click OK to create the vNIC template.

46.  Click OK.

47.  Under the FlexPod organization, right-click vNIC Templates.

48.  Select Create vNIC Template

49.  Enter vDS0-B as the vNIC template name.

50.  Select Fabric B.

51.  Do not select the Enable Failover checkbox.

52.  Set Redundancy Type to Secondary Template.

53.  Select vDS0-A for the Peer Redundancy Template.

54.  In the MAC Pool list, select MAC-Pool-B.

55.  Click OK to create the vNIC template.

56.  Click OK.

Create High Traffic VMware Adapter Policy

To create the optional VMware-High-Traffic Ethernet Adapter policy to provide higher vNIC performance, follow these steps:

1.     In Cisco UCS Manager, click Servers.

2.     Expand Policies > root.

3.     Right-click Adapter Policies and select Create Ethernet Adapter Policy.

4.     Name the policy VMware-HighTrf.

5.     Expand Resources and set the values as shown below.

6.     Expand Options and select Enabled for Receive Side Scaling (RSS).

 

7.     Click OK, then click OK again to complete creating the Ethernet Adapter Policy.

Create LAN Connectivity Policy for FC Boot (FCP)

To configure the necessary Infrastructure LAN Connectivity Policy within the FlexPod organization, follow these steps:

1.     In Cisco UCS Manager, click LAN.

2.     Expand LAN > Policies > root > Sub-Organizations > NA-FlexPod.

3.     Under the FlexPod Organization, right-click LAN Connectivity Policies.

4.     Select Create LAN Connectivity Policy.

5.     Enter FC-Boot as the name of the policy.

6.     Click the upper Add button to add a vNIC.

7.     In the Create vNIC dialog box, enter 00-vSwitch0-A as the name of the vNIC.

8.     Select the Use vNIC Template checkbox.

9.     In the vNIC Template list, select vSwitch0-A.

10.  In the Adapter Policy list, select VMWare.

11.  Click OK to add this vNIC to the policy.

12.  Click Add to add another vNIC to the policy.

13.  In the Create vNIC box, enter 01-vSwitch0-B as the name of the vNIC.

14.  Select the Use vNIC Template checkbox.

15.  In the vNIC Template list, select vSwitch0-B.

16.  In the Adapter Policy list, select VMWare.

17.  Click OK to add the vNIC to the policy.

18.  Click Add to add another vNIC to the policy.

19.  In the Create vNIC dialog box, enter 02-vDS0-A as the name of the vNIC.

20.  Select the Use vNIC Template checkbox.

21.  In the vNIC Template list, select vDS0-A.

22.  In the Adapter Policy list, select VMWare-HighTrf.

23.  Click OK to add this vNIC to the policy.

24.  Click Add to add another vNIC to the policy.

25.  In the Create vNIC box, enter 03-vDS0-B as the name of the vNIC.

26.  Select the Use vNIC Template checkbox.

27.  In the vNIC Template list, select vDS0-B.

28.  In the Adapter Policy list, select VMWare-HighTrf.

29.  Click OK to add this vNIC to the policy.

 

30.  Click OK, then click OK again to create the LAN Connectivity Policy.

Create vMedia Policy for VMware ESXi 6.7U2 ISO Install Boot

In the NetApp ONTAP setup steps, an HTTP web server is required, which is used for hosting ONTAP as well as VMware software. The vMedia Policy created will map the VMware ESXi 6.7U2 Cisco Custom ISO to the Cisco UCS server in order to boot the ESXi installation.  To create this policy, follow these steps:

1.     In Cisco UCS Manager, select Servers.

2.     Select Policies > root.

3.     Right-click vMedia Policies.

4.     Select Create vMedia Policy.

5.     Name the policy ESXi-6.7U2-HTTP.

6.     Enter “Mounts Cisco Custom ISO for ESXi 6.7U2” in the Description field.

7.     Click Add.

8.     Name the mount ESXi-6.7U2-HTTP.

9.     Select the CDD Device Type.

10.  Select the HTTP Protocol.

11.  Enter the IP Address of the web server.

12.  Enter VMware_ESXi_6.7.0_13006603_Custom_Cisco_6.7.2.1.iso as the Remote File name.

13.  Enter the web server path to the ISO file in the Remote Path field.

 

14.  Click OK to create the vMedia Mount.

15.  Click OK then click OK again to complete creating the vMedia Policy.

Create FC Boot Policy (FCP)

This procedure applies to a Cisco UCS environment in which two Fibre Channel logical interfaces (LIFs) are on cluster node 1 (fcp-lif011a and fcp-lif011b) and two Fibre Channel LIFs are on cluster node 2 (fcp-lif021a and fcp-lif021b). Also, it is assumed that the A LIFs are connected to Fabric A (Cisco UCS Fabric Interconnect A) and the B LIFs are connected to Fabric B (Cisco UCS Fabric Interconnect B).

To create a boot policy for the within the FlexPod organization, follow these steps:

1.     In Cisco UCS Manager, click Servers.

2.     Expand Policies > root > Sub-Organizations > NA-FlexPod.

3.     Under the FlexPod Organization, right-click Boot Policies.

4.     Select Create Boot Policy.

5.     Enter Boot-FCP-A as the name of the boot policy.

6.     Optional: Enter a description for the boot policy.

7.     Do not select the Reboot on Boot Order Change checkbox.

8.     Select the Uefi Boot Mode.

9.     Select the Boot Security checkbox.

10.  Expand Local Devices and select Add Remote CD/DVD.

11.  Expand vHBAs and select Add SAN Boot.

12.  Select Primary for the type field.

13.  Enter FCP-Fabric-A in the vHBA field.

14.  Click OK.

15.  From vHBAs, select Add SAN Boot Target.

16.  Keep 0 as the value for Boot Target LUN.

17.  Enter the WWPN for fcp-lif011a.

18.  Select Primary for the SAN boot target type.

19.  Click OK to add the SAN boot target.

20.  From vHBAs, select Add SAN Boot Target.

21.  Enter 0 as the value for Boot Target LUN.

22.  Enter the WWPN for fcp-lif021a.

23.  Click OK to add the SAN boot target.

24.  From vHBAs, select Add SAN Boot.

25.  In the Add SAN Boot dialog box, enter FCP-Fabric-B in the vHBA box.

26.  The SAN boot type should automatically be set to Secondary.

27.  Click OK.

28.  From vHBAs, select Add SAN Boot Target.

29.  Keep 0 as the value for Boot Target LUN.

30.  Enter the WWPN for fcp-lif011b.

31.  Select Primary for the SAN boot target type.

32.  Click OK to add the SAN boot target.

33.  From vHBAs, select Add SAN Boot Target.

34.  Keep 0 as the value for Boot Target LUN.

35.  Enter the WWPN for fcp-lif021b.

36.  Click OK to add the SAN boot target.

37.  Expand CIMC Mounted Media and select Add CIMC Mounted CD/DVD.

38.  Expand San > SAN Primary and select SAN Target Primary. Select Set Uefi Boot Parameters.

39.  Fill in the Set Uefi Boot Parameters exactly as shown in the following screenshot:

40.  Click OK to complete setting the Uefi Boot Parameters for the SAN Boot Target.

41.  Repeat this process to set Uefi Boot Parameters for each of the 4 SAN Boot Targets.

42.  Click OK, then click OK again to create the boot policy.

Create Service Profile Template (FCP)

In this procedure, one service profile template for Infrastructure ESXi hosts is created for Fabric A boot within the FlexPod organization. To create the service profile template, follow these steps:

1.     In Cisco UCS Manager, click Servers.

2.     Expand Service Profile Templates > root > Sub-Organizations > NA-FlexPod.

3.     Right-click the FlexPod Organization.

4.     Select Create Service Profile Template to open the Create Service Profile Template wizard.

5.     Enter VM-Host-Infra-FCP-A as the name of the service profile template. This service profile template is configured to boot from storage node 1 on fabric A.

6.     Select the “Updating Template” option.

7.     Under UUID, select UUID_Pool as the UUID pool.

8.     Click Next.

Configure Storage Provisioning

To configure storage provisioning, follow these steps:

1.     If you have servers with no physical disks, click on the Local Disk Configuration Policy and select the SAN-Boot Local Storage Policy. Otherwise, select the default Local Storage Policy.

2.     Click Next.

Configure Networking

To configure networking, follow these steps:

1.     Keep the default setting for Dynamic vNIC Connection Policy.

2.     Select the “Use Connectivity Policy” option to configure the LAN connectivity.

3.     Select FC-Boot from the LAN Connectivity Policy drop-down list.

4.     Leave Initiator Name Assignment at <not set>.

5.     Click Next.

Configure SAN Connectivity

To configure SAN connectivity, follow these steps:

1.     Select the Use Connectivity Policy option for the “How would you like to configure SAN connectivity?” field.

2.     Select the FC-Boot option from the SAN Connectivity Policy drop-down list.

3.     Click Next.

Configure Zoning

To configure zoning, follow this step:

1.     Set no zoning options and click Next.

Configure vNIC/HBA Placement

To configure vNIC/HBA placement, follow these steps:

1.     In the Select Placement list, retain the placement policy as Let System Perform Placement.

2.     Click Next.

Configure vMedia Policy

To configure the vMedia policy, follow these steps:

1.     Do not select a vMedia Policy.

2.     Click Next.

Configure Server Boot Order

To configure the server boot order, follow these steps:

1.     Select Boot-FCP-A for Boot Policy.

2.     Click Next.

Configure Maintenance Policy

To configure the maintenance policy, follow these steps:

1.     Change the Maintenance Policy to default.

 

2.     Click Next.

Configure Server Assignment

To configure server assignment, follow these steps:

1.     In the Pool Assignment list, select Infra-Pool.

2.     Select Down as the power state to be applied when the profile is associated with the server.

3.     Optional: select “B200-M5” for the Server Pool Qualification to select only B200 M5 servers in the pool.

4.     Expand Firmware Management and select the default Host Firmware Package.

 

5.     Click Next.

Configure Operational Policies

To configure the operational policies, follow these steps:

1.     In the BIOS Policy list, select VM-Host.

2.     Expand Power Control Policy Configuration and select No-Power-Cap in the Power Control Policy list.

 

3.     Click Finish to create the service profile template.

4.     Click OK in the confirmation message.

Create vMedia-Enabled Service Profile Template

To create a service profile template with vMedia enabled, follow these steps:

1.     Connect to UCS Manager and click Servers.

2.     Select Service Profile Templates > root > Sub-Organizations > NA-FlexPod  > Service Template VM-Host-Infra-FCP-A.

3.     Right-click VM-Host-Infra-FCP-A and select Create a Clone.

4.     Name the clone VM-Host-Infra-FC-A-vM.

5.     Click OK then click OK again to create the Service Profile Template clone.

6.     Select the newly-created VM-Host-Infra-FCP-A-vM and select the vMedia Policy tab.

7.     Click Modify vMedia Policy.

8.     Select the ESXi-6.7U2-HTTP vMedia Policy and click OK.

9.     Click OK to confirm.

Create Service Profiles

To create service profiles from the service profile template within the FlexPod organization, follow these steps:

1.     Connect to UCS Manager and click Servers.

2.     Select Service Profile Templates > root > Sub-Organizations > NA-FlexPod > Service Template VM-Host-Infra-FCP-A-vM.

3.     Right-click VM-Host-Infra-FCP-A-vM and select Create Service Profiles from Template.

4.     Enter VM-Host-Infra-0 as the service profile prefix.

5.     Enter 1 as “Name Suffix Starting Number.”

6.     Enter 3 as the “Number of Instances.”

7.     Click OK to create the service profiles.

8.     Click OK in the confirmation message.

9.     When VMware ESXi 6.7U2 has been installed on the hosts, the host Service Profiles can be bound to the VM-Host-Infra-FCP-A Service Profile Template to remove the vMedia Mapping from the host.

Add More Servers to FlexPod Unit

Additional server pools, service profile templates, and service profiles can be created in the respective organizations to add more servers to the FlexPod unit. All other pools and policies are at the root level and can be shared among the organizations.

Gather Necessary Information

After the Cisco UCS service profiles have been created, each infrastructure server in the environment will have a unique configuration. To proceed with the FlexPod deployment, specific information must be gathered from each Cisco UCS server and from the NetApp controllers. Insert the required information into Table 6  and Table 7  .

Table 6    WWPNs from NetApp Storage

Table 7    WWPNs for Cisco UCS Service Profiles

This section explains how to configure the Cisco MDS 9000s for use in a FlexPod environment. Follow the steps precisely because failure to do so could result in an improper configuration.

If directly connecting storage to the Cisco UCS fabric interconnects, skip this section.

Physical Connectivity

Follow the physical connectivity guidelines for FlexPod as explained in the section FlexPod Cabling.

FlexPod Cisco MDS Base

The following procedures describe how to configure the Cisco Nexus switches for use in a base FlexPod environment. This procedure assumes you are using the Cisco MDS 9132T with NX-OS 8.4(1).

Cisco MDS 9132T A

To set up the initial configuration for the Cisco MDS A switch, <mds-A-hostname>, follow these steps:

1.     Configure the switch using the command line.

2.     Review the configuration.

Cisco MDS 9132T B

To set up the initial configuration for the Cisco MDS B switch, <mds-B-hostname>, follow these steps:

1.     Configure the switch using the command line.

2.     Review the configuration.

FlexPod Cisco MDS Switch Configuration

Enable Licenses

Cisco MDS 9132T A and Cisco MDS 9132T B

To enable the correct features on the Cisco MDS switches, follow these steps:

1.     Log in as admin.

2.     Run the following commands:

Add Second NTP Server

Cisco MDS 9132T A and Cisco MDS 9132T B

To configure the second NTP server, follow this step:

From the global configuration mode, run the following command:

Configure Individual Ports

Cisco MDS 9132T A

To configure individual ports and port-channels for switch A, follow this step:

From the global configuration mode, run the following commands:

Cisco MDS 9132T B

To configure individual ports and port-channels for switch B, follow this step:

From the global configuration mode, run the following commands:

Create VSANs

Cisco MDS 9132T A

To create the necessary VSANs for fabric A and add ports to them, follow these steps:

From the global configuration mode, run the following commands:

Cisco MDS 9132T B

To create the necessary VSANs for fabric B and add ports to them, follow these steps:

From the global configuration mode, run the following commands:

Create Device Aliases

Cisco MDS 9132T A

To create device aliases for Fabric A that will be used to create zones, follow these steps:

From the global configuration mode, run the following commands:

Cisco MDS 9132T B

To create device aliases for Fabric B that will be used to create zones, follow these steps:

From the global configuration mode, run the following commands:

Create Zones and Zoneset

Cisco MDS 9132T A

To create the required zones and zoneset on Fabric A, run the following commands:

Cisco MDS 9132T B

To create the required zones and zoneset on Fabric B, run the following commands:

ONTAP Boot Storage Setup

Create igroups

Create igroups by entering the following commands from the storage cluster management node SSH connection:

To view the three igroups just created, use the command lun igroup show.

Map Boot LUNs to igroups

From the storage cluster management SSH connection, enter the following commands:

VMware ESXi 6.7U2

This section provides detailed instructions for installing VMware ESXi 6.7U2 in a FlexPod environment. After the procedures are completed, two booted ESXi hosts will be provisioned.

Several methods exist for installing ESXi in a VMware environment. These procedures focus on how to use the built-in keyboard, video, mouse (KVM) console and virtual media features in Cisco UCS Manager to map remote installation media to individual servers and connect to their boot logical unit numbers (LUNs).

Download ESXi 6.7U2 from VMware

If the VMware ESXi ISO has not been downloaded, follow these steps:

1.     Click the following link: Cisco Custom ESXi 6.7U2 ISO.

2.     You will need a user id and password on vmware.com to download this software.

3.     Download the .iso file.

Log into Cisco UCS 6454 Fabric Interconnect

Cisco UCS Manager

The Cisco UCS IP KVM enables the administrator to begin the installation of the operating system (OS) through remote media. It is necessary to log in to the Cisco UCS environment to run the IP KVM.

To log into the Cisco UCS environment, follow these steps:

1.     Open a web browser and enter the IP address for the Cisco UCS cluster address. This step launches the Cisco UCS Manager application.

2.     Click the Launch UCS Manager link to launch the HTML 5 UCS Manager GUI.

3.     If prompted to accept security certificates, accept as necessary.

4.     When prompted, enter admin as the user name and enter the administrative password.

5.     To log in to Cisco UCS Manager, click Login.

6.     From the main menu, click Servers.

7.     Select Servers > Service Profiles > root > Sub-Organizations > FlexPod Organization > VM-Host-Infra-01.

8.     In the Actions pane, click >> to the right of KVM Console.

9.     Select the “Launch Java KVM Console” checkbox and click OK to launch the console.

10.  Follow the prompts to launch the Java-based KVM console.

11.  Select Servers > Service Profiles > root > Sub-Organizations > FlexPod Organization > VM-Host-Infra-02.

12.  In the Actions pane, click >> to the right of KVM Console.

13.  Select the “Launch Java KVM Console” checkbox and click OK to launch the console.

14.  Follow the prompts to launch the Java-based KVM console.

Set Up VMware ESXi Installation

ESXi Hosts VM-Host-Infra-01, VM-Host-Infra-02, and VM-Host-Infra-03

To prepare the server for the OS installation, follow these steps on each ESXi host:

1.     In the KVM window, click Virtual Media.

2.     Select Activate Virtual Devices.

3.     If prompted to accept an Unencrypted KVM session, accept as necessary.

4.     Click Virtual Media and select Map CD/DVD.

5.     Browse to the ESXi installer ISO image file and click Open.

6.     Click Map Device.

7.     Click the KVM Console tab to monitor the server boot.

Install ESXi

ESXi Hosts VM-Host-Infra-01, VM-Host-Infra-02, and VM-Host-Infra-03

To install VMware ESXi to the bootable LUN of the hosts, follow these steps on each host:

1.     Boot the server by selecting Boot Server in the KVM and click OK, then click OK again.

2.     On boot, the machine detects the presence of the ESXi installation media and loads the ESXi installer.

3.     After the installer is finished loading, press Enter to continue with the installation.

4.     Read and accept the end-user license agreement (EULA). Press F11 to accept and continue.

5.     Select the LUN that was previously set up as the installation disk for ESXi and press Enter to continue with the installation.

6.     Select the appropriate keyboard layout and press Enter.

7.     Enter and confirm the root password and press Enter.

8.     The installer issues a warning that the selected disk will be repartitioned. Press F11 to continue with the installation.

9.     After the installation is complete, press Enter to reboot the server.

10.  In Cisco UCS Manager, bind the current service profile to the non-vMedia service profile template to prevent mounting the ESXi installation iso over HTTP.

Set Up Management Networking for ESXi Hosts

Adding a management network for each VMware host is necessary for managing the host. To add a management network for the VMware hosts, follow these steps on each ESXi host:

ESXi Host VM-Host-Infra-01, VM-Host-Infra-02, and VM-Host-Infra-03

To configure each ESXi host with access to the management network, follow these steps:

1.     After the server has finished rebooting, press F2 to customize VMware ESXi.

2.     Log in as root, enter the corresponding password, and press Enter to log in.

3.     Select Troubleshooting Options and press Enter.

4.     Select Enable ESXi Shell and press Enter.

5.     Select Enable SSH and press Enter.

6.     Press Esc to exit the Troubleshooting Options menu.

7.     Select the Configure Management Network option and press Enter.

8.     Select Network Adapters and press Enter.

9.     Verify that the numbers in the Hardware Label field match the numbers in the Device Name field.

10.  Using the spacebar, select vmnic1.

 

11.  Press Enter.

12.  Select the VLAN (Optional) option and press Enter.

13.  Enter the <ib-mgmt-vlan-id> and press Enter.

14.  Select IPv4 Configuration and press Enter.

15.  Select the “Set static IPv4 address and network configuration” option by using the arrow keys and space bar.

16.  Move to the IPv4 Address field and enter the IP address for managing the ESXi host.

17.  Move to the Subnet Mask field and enter the subnet mask for the ESXi host.

18.  Move to the Default Gateway field and enter the default gateway for the ESXi host.

19.  Press Enter to accept the changes to the IP configuration.

20.  Select the IPv6 Configuration option and press Enter.

21.  Using the spacebar, select Disable IPv6 (restart required) and press Enter.

22.  Select the DNS Configuration option and press Enter.

23.  Using the spacebar, select “Use the following DNS server addresses and hostname:”

24.  Move to the Primary DNS Server field and enter the IP address of the primary DNS server.

25.  Optional: Move to the Alternate DNS Server field and enter the IP address of the secondary DNS server.

26.  Move to the Hostname field and enter the fully qualified domain name (FQDN) for the ESXi host.

27.  Press Enter to accept the changes to the DNS configuration.

28.  Press Esc to exit the Configure Management Network submenu.

29.  Press Y to confirm the changes and reboot the ESXi host.

Reset VMware ESXi Host VMkernel Port vmk0 MAC Address (Optional)

ESXi Host VM-Host-Infra-01, VM-Host-Infra-02, and VM-Host-Infra-03

By default, the MAC address of the management VMkernel port vmk0 is the same as the MAC address of the Ethernet port it is placed on.  If the ESXi host’s boot LUN is remapped to a different server with different MAC addresses, a MAC address conflict will exist because vmk0 will retain the assigned MAC address unless the ESXi System Configuration is reset.  To reset the MAC address of vmk0 to a random VMware-assigned MAC address, follow these steps:

1.     From the ESXi console menu main screen, type Ctrl-Alt-F1 to access the VMware console command line interface.  In the UCSM KVM, Ctrl-Alt-F1 appears in the list of Static Macros.

2.     Log in as root.

3.     Type esxcfg-vmknic –l to get a detailed listing of interface vmk0.  vmk0 should be a part of the “Management Network” port group. Note the IP address and netmask of vmk0.

4.     To remove vmk0, type esxcfg-vmknic –d “Management Network”.

5.     To re-add vmk0 with a random MAC address, type esxcfg-vmknic –a –i <vmk0-ip> -n <vmk0-netmask> “Management Network”.

6.     Verify vmk0 has been re-added with a random MAC address by typing esxcfg-vmknic –l.

7.     Tag vmk0 as the management interface by typing esxcli network ip interface tag add -i vmk0 -t Management.

8.     When vmk0 was re-added, if a message popped up saying vmk1 was marked as the management interface, type esxcli network ip interface tag remove -i vmk1 -t Management.

9.     Type exit to log out of the command line interface.

10.  Type Ctrl-Alt-F2 to return to the ESXi console menu interface.

Install VMware Drivers for the Cisco Virtual Interface Card (VIC) and ESXi Host

Download and extract the offline bundle for the following VMware VIC Drivers and the NetApp NFS Plug-in for VMware VAAI to the Management workstation:

nfnic Driver version 4.0.0.38

nenic Driver version 1.0.29.0

NetApp NFS Plug-in 1.1.2 for VMware VAAI (This is the offline bundle and does not need to be extracted.)

ESXi Hosts VM-Host-Infra-01, VM-Host-Infra-02, and VM-Host-Infra-03

To install VMware VIC Drivers and the NetApp NFS Plug-in for VMware VAAI on the ESXi host VM-Host-Infra-01 and VM-Host-Infra-02, follow these steps:

1.     Using an SCP program such as WinSCP, copy the three offline bundles referenced above to the /tmp directory on each ESXi host.

2.     Using an ssh tool such as PuTTY, ssh to each VMware ESXi host. Log in as root with the root password.

3.     Type cd /tmp.

4.     Run the following commands on each host:

Log into the First VMware ESXi Host by Using VMware Host Client

ESXi Host VM-Host-Infra-01

To log into the VM-Host-Infra-01 ESXi host by using the VMware Host Client, follow these steps:

1.     Open a web browser on the management workstation and navigate to the VM-Host-Infra-01 management IP address.

2.     Enter root for the user name.

3.     Enter the root password.

4.     Click Login to connect.

5.     Decide whether to join the VMware Customer Experience Improvement Program and click OK.

Set Up VMkernel Ports and Virtual Switch

ESXi Host VM-Host-Infra-01

To set up the VMkernel ports and the virtual switches on the first ESXi host, follow these steps:

1.     From the Host Client, select Networking.

2.     In the center pane, select the Virtual switches tab.

3.     Highlight the vSwitch0 line.

4.     Select Edit settings.

5.     Change the MTU to 9000.

6.     Expand NIC teaming.

7.     In the Failover order section, select vmnic1 and click Mark active.

8.     Verify that vmnic1 now has a status of Active.

9.     Click Save.

10.  Select Networking, then select the Port groups tab.

11.  In the center pane, right-click VM Network and select Remove.

12.  Click Remove to complete removing the port group.

13.  In the center pane, select Add port group.

14.  Name the port group IB-MGMT Network and enter <ib-mgmt-vlan-id> in the VLAN ID field, and make sure Virtual switch vSwitch0 is selected.

15.  Click Add to finalize the edits for the IB-MGMT Network.

16.  At the top, select the VMkernel NICs tab.

17.  Click Add VMkernel NIC.

18.  For New port group, enter VMkernel-vMotion.

19.  For Virtual switch, select vSwitch0.

20.  Enter <vmotion-vlan-id> for the VLAN ID.

21.  Change the MTU to 9000.

22.  Select Static IPv4 settings and expand IPv4 settings.

23.  Enter the ESXi host vMotion IP address and netmask.

24.  Select the vMotion stack for TCP/IP stack.

25.  Click Create.

26.  Click Add VMkernel NIC.

27.  For New port group, enter VMkernel-Infra-NFS

28.  For Virtual switch, select vSwitch0.

29.  Enter <infra-nfs-vlan-id> for the VLAN ID

30.  Change the MTU to 9000.

31.  Select Static IPv4 settings and expand IPv4 settings.

32.  Enter the ESXi host Infrastructure NFS IP address and netmask.

33.  Do not select any of the Services.

34.  Click Create.

35.  Select the Virtual Switches tab, then vSwitch0. The properties for vSwitch0 VMkernel NICs should be similar to the following example:

36.  Select Networking and the VMkernel NICs tab to confirm configured virtual adapters. The adapters listed should be similar to the following example:

Mount Required Datastores

ESXi Host VM-Host-Infra-01

To mount the required datastores, follow these steps on the first ESXi host:

1.     From the Host Client, select Storage.

2.     In the center pane, select the Datastores tab.

3.     In the center pane, select New Datastore to add a new datastore.

4.     In the New datastore popup, select Mount NFS datastore and click Next.

 

5.     Input infra_datastore for the datastore name.  Input the IP address for the nfs-lif02 LIF for the NFS server.  Input /infra_datastore for the NFS share.  Leave the NFS version set at NFS 3.  Click Next.

6.     Click Finish. The datastore should now appear in the datastore list.

7.     In the center pane, select New Datastore to add a new datastore.

8.     In the New datastore popup, select Mount NFS datastore and click Next.

9.     Input infra_swap for the datastore name.  Input the IP address for the nfs-lif01 LIF for the NFS server.  Input /infra_swap for the NFS share.  Leave the NFS version set at NFS 3.  Click Next.

10.  Click Finish. The datastore should now appear in the datastore list.

Configure NTP on First ESXi Host

ESXi Host VM-Host-Infra-01

To configure Network Time Protocol (NTP) on the first ESXi host, follow these steps:

1.     From the Host Client, select Manage.

2.     In the center pane, select System > Time & Date.

3.     Click Edit settings.

4.     Make sure Use Network Time Protocol (enable NTP client) is selected.

5.     Use the drop-down list to select Start and stop with host.

6.     Enter the two Nexus switch NTP addresses in the NTP servers box separated by a comma.

 

7.     Click Save to save the configuration changes.

8.     Select Actions > NTP service > Start.

9.     Verify that NTP service is now running and the clock is now set to approximately the correct time. The timezone will be UTC.

Configure ESXi Host Swap

ESXi Host VM-Host-Infra-01

To configure host swap on the first ESXi host, follow these steps on the host:

1.     From the Host Client, select Manage.

2.     In the center pane, select System > Swap.

3.     Click Edit settings.

4.     Use the drop-down list to select infra_swap. Leave all other settings unchanged.

5.     Click Save to save the configuration changes.

6.     If you are implementing iSCSI boot, execute the VMware ESXi setup scripts in the iSCSI Addition Appendix.

VMware vCenter 6.7U2

The procedures in the following subsections provide detailed instructions for installing the VMware vCenter 6.7U2 Server Appliance in a FlexPod environment. After the procedures are completed, a VMware vCenter Server will be configured.

Build the VMware vCenter Server Appliance

The VCSA deployment consists of 2 stages: install and configuration. To build the VMware vCenter virtual machine, follow these steps:

1.     Locate and copy the VMware-VCSA-all-6.7.0-13643870.iso file to the desktop of the management workstation.  This ISO is for the VMware vSphere 6.5 U2 vCenter Server Appliance.

2.     Using ISO mounting software, mount the ISO image as a disk on the management workstation. (For example, with the Mount command in Windows Server 2012).

3.     In the mounted disk directory, navigate to the vcsa-ui-installer > win32 directory and double-click installer.exe. The vCenter Server Appliance Installer wizard appears.

4.     Click Install to start the vCenter Server Appliance deployment wizard.

5.     Click Next in the Introduction section.

6.     Read and accept the license agreement and click NEXT.

7.     In the “Select deployment type” section, select Embedded Platform Services Controller and click NEXT.

8.     In the “Appliance deployment target”, enter the host name or IP address of the first ESXi host, User name (root) and Password.

   

9.     Click Yes to accept the certificate.

10.  Enter the Appliance VM name and password details in the “Set up appliance VM” section. Click NEXT.

   

11.  In the “Select deployment size” section, Select the deployment size and Storage size. For example, “Small.”

12.  Click NEXT.

 

13.  Select infra_datastore. Click NEXT.

 

14.  In the “Network Settings” section, configure the below settings:

a.     Choose a Network: IB-MGMT Network.

b.     IP version: IPV4

c.     IP assignment: static

d.     System name: <vcenter-fqdn>

e.     IP address: <vcenter-ip>

f.      Subnet mask or prefix length: <vcenter-subnet-mask>

g.     Default gateway: <vcenter-gateway>

h.     DNS Servers: <dns-server1>, <dns-server2>

15.  Click NEXT.

16.  Review all values and click Finish to complete the installation.

17.  The vCenter appliance installation will take a few minutes to complete.

18.  Click CONTINUE to proceed with stage 2 configuration.

19.  Click NEXT.

20.  In the Appliance Configuration, configure these settings:

a.     Time Synchronization Mode: Synchronize time with NTP servers.

b.     NTP Servers: <switch-a-ntp-ip>, <switch-b-ntp-ip>

c.     SSH access: Enabled.

21.  Click NEXT.

22.  Complete the SSO configuration as shown below:

23.  Click NEXT.

24.  Decide whether to join VMware’s Customer Experience Improvement Program (CEIP).

25.  Click NEXT.

26.  Review the configuration and click FINISH.

27.  Click OK.

 

28.  Click CLOSE. Eject or unmount the VCSA installer ISO.

Adjust vCenter CPU Settings

If a vCenter deployment size of Small or larger was selected in the vCenter setup, it is possible that the VCSA’s CPU setup does not match the UCS server CPU hardware configuration. Cisco UCS B200 and C220 servers are 2-socket servers. In this validation, the Small deployment size was selected and vCenter was setup for a 4-socket server.  This setup will cause issues in the VMware ESXi cluster Admission Control.  To resolve the Admission Control issue, follow these steps:

1.     Open a web browser on the management workstation and navigate to the VM-Host-Infra-01 management IP address.

2.     Click Open the VMware Host Client.

3.     Enter root for the user name.

4.     Enter the root password.

5.     Click Login to connect.

6.     On the left, select Virtual Machines.

7.     In the center pane, right-click the vCenter VM and select Edit settings.

8.     In the Edit settings window, expand CPU and check the value of Sockets.

9.     If the number of Sockets is greater than 2, it will need to be adjusted. Click Cancel.

10.  If the number of Sockets needs to be adjusted:

a.     Right-click the vCenter VM and select Guest OS > Shut down. Click Yes on the confirmation.

b.     Once vCenter is shut down, right-click the vCenter VM and select Edit settings.

c.     In the Edit settings window, expand CPU and change the Cores per Socket value to make the Sockets value 2.

d.     Click Save.

e.     Right-click the vCenter VM and select Power > Power on. Wait approximately 10 minutes for vCenter to come up.

Setup VMware vCenter Server

To setup the VMware vCenter Server, follow these steps:

1.     Using a web browser, navigate to https://<vcenter-ip-address>. You will need to navigate security screens.

2.     Select LAUNCH VSPHERE CLIENT (HTML5).

3.     Log in using the Single Sign-On username (administrator@vsphere.local) and password created during the vCenter installation.

4.     In the center pane, select ACTIONS > New Datacenter.

5.     Type “FlexPod-DC” in the Datacenter name field.

6.     Click OK.

7.     Right-click the datacenter FlexPod-DC in the list in the left pane. Select New Cluster.

8.     Name the cluster FlexPod-Management.

9.     Turn on DRS and vSphere HA. Do not turn on vSAN.

10.  Click OK to create the new cluster.

11.   Expand “FlexPod-DC”.

12.  Right-click “FlexPod-Management” and select Settings.

13.  Select Configuration > General in the list located on the left and select EDIT located on the right of General.

14.  Select Datastore specified by host and click OK.

 

15.  Right-click “FlexPod-Management” and click Add Hosts.

16.  In the IP address or FQDN field, enter either the IP address or the FQDN name of the first VMware ESXi host. Enter root as the Username and the root password. Click NEXT.

17.  Verify the Host summary information and click NEXT.

18.  Ignore warnings about the host being moved to Maintenance Mode and click FINISH to complete adding the host to the cluster.

19.  The added ESXi host will have Warnings that the ESXi Shell and SSH have been enabled. These warnings can be suppressed.

20.  In the list, right-click the added ESXi host and select Settings.

21.  In the center pane under Virtual Machines, select Swap file location.

22.  On the right, click EDIT.

23.  Select the infra_swap datastore and click OK.

24.  In the list under Storage, select Storage Devices. Make sure the NETAPP Fibre Channel Disk 0 is selected.

25.  Select the Paths tab.

26.  Ensure that 4 fibre channel paths appear, two of which should have the status Active (I/O).

Add AD User Authentication to vCenter (Optional)

If an AD Infrastructure is set up in this FlexPod environment, you can setup in AD and authenticate from vCenter.

To add an AD user authentication to the vCenter, follow these steps:

1.     In the AD Infrastructure, using the Active Directory Users and Computers tool, setup a Domain Administrator user with a user name such as flexadmin (FlexPod Admin).

2.     Connect to https://<vcenter-ip> and select LAUNCH VSPHERE CLIENT (HTML5).

3.     Log in as Administrator@vsphere.local (or the SSO user set up in vCenter installation) with the corresponding password.

4.     Under Menu, select Administration. In the list on the left, under Single Sign On, select Configuration.

5.     In the center pane, under Configuration, select the Active Directory Domain tab.

6.     Select JOIN AD.

7.     Fill in the AD domain name, the Administrator user, and the domain Administrator password.  Do not fill in an Organizational unit. Click JOIN.

8.     In the list on the left under Deployment, select System Configuration. Select the radio button to select the vCenter, then select REBOOT NODE.

9.     Input a reboot reason and click OK.  The reboot will take approximately 10 minutes for full vCenter initialization. 

10.  Log back into the vCenter vSphere HTML5 Client.

11.  Under Menu, select Administration. In the list on the left, under Single Sign On, select Configuration.

12.  In the center pane, under Configuration, select the Active Directory Domain tab.

13.  Make sure your Active Directory Domain is listed.

14.  Select the Identity Sources tab.

15.  Select ADD IDENTITY SOURCE.

16.  Select the Active Directory (Integrated Windows Authentication) Identity source type. Your AD domain name should be filled in.  Leave Use machine account selected and click ADD. Your AD domain should now appear in the Identity Sources list.

17.  On the left under Access Control, select Global Permissions.

18.  In the center pane, click the + sign to add a Global Permission.

19.  In the Add Permission window, select your AD domain for the User.

20.  On the search line, enter either the FlexPod Admin username or the Domain Admins group. Leave the Role set to Administrator. Select the Propagate to children checkbox.

21.  Click OK to add the selected User or Group. The user or group should now appear in the Global Permissions list with the Administrator role.

22.  Log out and log back into the vCenter HTML5 Client as the FlexPod Admin user.  You will need to add the domain name to the user, for example, flexadmin@domain.

FlexPod VMware vSphere Distributed Switch (vDS)

This section provides detailed procedures for installing the VMware vDS on the FlexPod ESXi Management Host. 

In the Cisco UCS setup section of this document two sets of vNICs were setup.  The vmnic ports associated with the vDS0-A and B vNICs will be placed on the VMware vDS in this procedure. The vMotion VMkernel port will be placed on the vDS.

An IB-MGMT, vMotion, and a VM-Traffic port group will be added to the vDS.  Any additional VLAN-based port groups added to the vDS would need to have the corresponding VLANs added to the Cisco UCS LAN cloud, to the Cisco UCS vDS0-A and B vNIC templates, and to the Cisco Nexus 9K switches and vPC peer-link interfaces on the switches.

In this document, the infrastructure ESXi management VMkernel ports, the vCenter management interface, and the infrastructure NFS VMkernel ports are left on vSwitch0 to facilitate bringing the virtual environment back up in the event it needs to be completely shut down. The vMotion VMkernel ports are moved to the vDS to allow QoS marking of vMotion to be done at the VLAN level in the vDS if vMotion needs to have QoS policies applied in the future. The vMotion port group is also pinned to Cisco UCS fabric B.  Pinning is better done in a vDS to ensure consistency across all ESXi hosts.

Configure the VMware vDS in vCenter

VMware vSphere Web Client

To configure the vDS, follow these steps:

1.     After logging into the VMware vSphere HTML5 Client, select Networking under Menu. 

2.     Right-click the FlexPod-DC datacenter and select Distributed Switch > New Distributed Switch.

3.     Give the Distributed Switch a descriptive name (vDS0) and click NEXT.

4.     Make sure Distributed switch: 6.6.0 is selected and click NEXT.

5.     Change the Number of uplinks to 2. If VMware Network I/O Control is to be used for Quality of Service, leave Network I/O Control Enabled.  Otherwise, Disable Network I/O Control. Enter VM-Traffic for the Port group name. Click NEXT.

6.     Review the information and click FINISH to complete creating the vDS.

7.     Expand the FlexPod-DC datacenter and the newly created vDS.  Select the newly created vDS.

8.     Right-click the VM-Traffic port group and select Edit Settings.

9.     Select VLAN.

10.  Select VLAN for VLAN type and enter the VM-Traffic VLAN ID. Click OK.

11.  Right-click the vDS and select Settings > Edit Settings.

12.   in the Edit Settings window, select Advanced.

13.  Change the MTU to 9000.  The Discovery Protocol can optionally be changed to Link Layer Discovery Protocol and the Operation to Both.  Click OK.

14.  For the first port group used for vMotion, right-click the vDS, select Distributed Port Group, and select New Distributed Port Group.

15.  Enter vMotion as the name and click NEXT.

16.  Set the VLAN type to VLAN, enter the VLAN ID used for vMotion, click the Customize default policies configuration check box, and click NEXT.

17.  Leave the Security options set to Reject and click NEXT.

18.  Leave the Ingress and Egress traffic shaping options as Disabled and click NEXT.

19.  Select Uplink 1 from the list of Active uplinks and click the down arrow icon twice to place Uplink 1 in the list of Standby uplinks. This will pin all vMotion traffic to UCS Fabric Interconnect B except when a failure occurs.

 

20.  Click NEXT.

21.  Leave NetFlow disabled and click NEXT.

22.  Leave Block all ports set as No and click NEXT.

23.  Confirm the options and click FINISH to create the port group.

24.  For the second port group used for Infrastructure In-Band Management, right-click the vDS, select Distributed Port Group, and select New Distributed Port Group.

25.  Enter IB-MGMT as the name and click NEXT.

26.  Set the VLAN type to VLAN, enter the VLAN ID used for In-Band Management, do not select the Customize default policies configuration check box, and click NEXT.

27.  Confirm the options and click FINISH to create the port group.

28.  Right-click the vDS and select Add and Manage Hosts.

29.  Make sure Add hosts is selected and click NEXT.

30.  Click the green + sign to add New hosts.  Select the one configured FlexPod Management host and click OK. Click NEXT.

31.  Select vmnic2 and click Assign uplink. Select Uplink 1 and click OK. Select vmnic3 and click Assign uplink. Select Uplink 2 and click OK.

32.  Click NEXT.

33.  Select vmk1 (VMkernel vMotion) and click Assign port group.

34.  Select the vMotion destination port group and click OK.

35.  Do not migrate the other VMkernel ports.

36.  Confirm the vMotion VMkernel adapter has a valid and correct Destination Port Group and click NEXT.

37.  Click NEXT.

38.  Click FINISH to complete adding the ESXi host to the vDS.

Add and Configure a VMware ESXi Host in vCenter

This section details the steps to add and configure an ESXi host in vCenter. This section assumes the host has had VMware ESXi 6.7U2 installed, the management IP address set, and the VIC drivers and NetApp NFS Plug-in for VMware VAAI installed. This procedure is initially being run on the second and third ESXi management hosts but can be run on any added ESXi host.

Add the ESXi Host to vCenter

ESXi Host VM-Host-Infra-02 and VM-Host-Infra-03

To add the ESXi host(s) to vCenter, follow these steps:

1.     From the Home screen in the VMware vCenter HTML5 Interface, select Menu > Hosts and Clusters.

2.     Right-click the “FlexPod-Management” cluster and click Add Hosts.

3.     In the IP address or FQDN field, enter either the IP address or the FQDN name of the configured VMware ESXi host. Also enter the user id (root) and associated password. If more than one host is being added, add the corresponding host information. Click NEXT.

4.     Select all hosts being added and click OK to accept the certificate(s).

5.     Review the host details and click NEXT to continue.

6.     Review the configuration parameters and click FINISH to add the host.

7.     The added ESXi host(s) will have Warnings that the ESXi Shell and SSH have been enabled. These warnings can be suppressed.

Set Up VMkernel Ports and Virtual Switch

ESXi Host VM-Host-Infra-02 and VM-Host-Infra-03

To set up the VMkernel ports and the virtual switches on the ESXi host, follow these steps:

1.     In the vCenter HTML5 Interface, under Hosts and Clusters select the ESXi host.

2.     In the center pane, select the Configure tab.

3.     In the list, select Virtual switches under Networking.

4.     Select vSwitch0.

5.     Select EDIT to Edit settings.

6.     Change the MTU to 9000.

7.     Select Teaming and failover located on the left.

8.     In the Failover order section, use the arrow icons to move the vmnics until both are Active adapters.

9.     Click OK.

10.  In the center pane, select VM Network and click … > Edit Settings to edit settings.

11.  Rename the port group IB-MGMT Network and enter <ib-mgmt-vlan-id> in the VLAN ID field.

12.  Click OK to finalize the edits for the IB-MGMT Network.

13.  Located on the left under Networking, select VMkernel adapters.

14.  In the center pane, click Add Networking.

15.  Make sure VMkernel Network Adapter is selected and click NEXT.

16.  Select an existing standard switch and click BROWSE. Select vSwitch0 and click OK. Click NEXT.

17.  For Network label, enter VMkernel-Infra-NFS.

18.  Enter <infra-nfs-vlan-id> for the VLAN ID.

19.  Select Custom for MTU and make sure 9000 is entered.

20.  Leave the Default TCP/IP stack selected and do not select any of the Enabled services. Click NEXT.

21.  Select Use static IPv4 settings and enter the IPv4 address and subnet mask for the Infra-NFS VMkernel port for this ESXi host.

22.  Click NEXT.

23.  Review the settings and click FINISH to create the VMkernel port.

24.  On the left under Networking, select Virtual switches. Then select vSwitch0. The properties for vSwitch0 should be similar to the following example:

25.  Repeat this procedure for all hosts being added.

Mount Required Datastores

ESXi Host VM-Host-Infra-02 and VM-Host-Infra-03

To mount the required datastores, follow these steps on the ESXi host(s):

1.     From the vCenter Home screen, select Menu > Storage.

2.     Located on the left, expand FlexPod-DC.

3.     Located on the left, right-click infra_datastore and select Mount Datastore to Additional Hosts.

4.     Select the ESXi host(s) and click OK.

 

5.     Repeat this process to mount the infra_swap datastore to the ESXi host(s).

6.     On the left, select infra_datastore. In the center pane, select Hosts. Verify the ESXi host(s) now has the datastore mounted. Repeat this process to also verify that infra_swap is also mounted.

Configure NTP on ESXi Host

ESXi Host VM-Host-Infra-02 and VM-Host-Infra-03

To configure Network Time Protocol (NTP) on the ESXi host(s), follow these steps:

1.     In the vCenter HTML5 Interface, under Hosts and Clusters select the ESXi host.

2.     In the center pane, select the Configure tab.

3.     In the list under System, select Time Configuration.

4.     Located on the right, click EDIT.

5.     Select Use Network Time Protocol (enable NTP client).

6.     Enter the two Nexus switch NTP IP addresses in the NTP servers box separated by a comma.

7.     Click the Start NTP Service checkbox.

8.     Use the drop-down list to select Start and stop with host.

9.     Click OK to save the configuration changes.

10.  Verify that NTP service is now enabled and running and the clock is now set to approximately the correct time.

Configure ESXi Host Swap

ESXi Host VM-Host-Infra-02 and VM-Host-Infra-03

To configure host swap on the ESXi host(s), follow these steps on the host:

1.     In the vCenter HTML5 Interface, under Hosts and Clusters select the ESXi host.

2.     In the center pane, select the Configure tab.

3.     In the list under System, select System Swap.

4.     Located on the right, click EDIT.

5.     Select Can use datastore and use the drop-down list to select infra_swap. Leave all other settings unchanged.

6.     Click OK to save the configuration changes.

7.     In the list under Virtual Machines, select Swap File Location.

8.     Located on the right, select Edit.

9.     Select infra_swap and click OK.

Check ESXi Host Fibre Channel Pathing

ESXi Host VM-Host-Infra-02 and VM-Host-Infra-03

To ensure that the ESXi host(s) boot disk contains all required fibre channel paths, follow these steps:

1.     In the list under Storage, select Storage Devices. Make sure the NETAPP Fibre Channel Disk is selected.

2.     Select the Paths tab.

3.     Ensure that 4 fibre channel paths appear, two of which should have the status Active (I/O).

Add the ESXi Host(s) to the VMware Virtual Distributed Switch

ESXi Host VM-Host-Infra-02 and VM-Host-Infra-03

To add the ESXi host(s) to the VMware vDS, follow these steps on the host:

1.     After logging into the VMware vSphere HTML5 Client, select Networking under Menu.

2.     Right-click the vDS (vDS0) and select Add and Manage Hosts.

3.     Make sure Add hosts is selected and click NEXT.

4.     Click the green + sign to add New hosts.  Select the configured FlexPod Management host(s) and click OK. Click NEXT.

5.     Select vmnic2 on each host and click Assign uplink. Select Uplink 1 and click OK. Select vmnic3 on each host and click Assign uplink. Select Uplink 2 and click OK. If more than one host is being connected to the vDS, use the Apply this uplink assignment to the rest of the hosts checkbox.

6.     Click NEXT.

7.     Do not migrate any VMkernel ports and click NEXT.

8.     Do not migrate any VM ports and click NEXT.

9.     Click FINISH to complete adding the ESXi host(s) to the vDS.

Add the vMotion VMkernel Port to the ESXi Host

ESXi Host VM-Host-Infra-02 and VM-Host-Infra-03

To add the vMotion VMkernel Port to the ESXi host(s) on the VMware vDS, follow these steps on the host:

1.     In the vCenter HTML5 Interface, under Hosts and Clusters select the ESXi host.

2.     In the center pane, select the Configure tab.

3.     In the list under Networking, select VMkernel adapters.

4.     Select Add Networking to Add host networking.

5.     Make sure VMkernel Network Adapter is selected and click NEXT.

6.     Select BROWSE to the right of Select an existing network.

7.     Select vMotion on the vDS and click OK.

8.     Click NEXT.

9.     Make sure the Network label is vMotion with the vDS in parenthesis. Using the pulldown, select Custom for MTU and make sure the MTU is set to 9000. Select the vMotion TCP/IP stack and click NEXT.

10.  Select Use static IPv4 settings and input the host’s vMotion IPv4 address and Subnet mask.

11.  Click NEXT.

12.  Review the parameters and click FINISH to add the vMotion VMkernel port.

13.  If NetApp VSC is installed, under Hosts and Clusters, right-click the host and select NetApp VSC > Set Recommended Values. Reboot the host.

VMware ESXi 6.7U2 TPM Attestation

If your Cisco UCS servers have Trusted Platform Module (TPM) 2.0 modules installed, the TPM can provide assurance that ESXi has booted with UEFI Secure Boot enabled and using only digitally signed code. In the Cisco UCS section of this document, UEFI secure boot was enabled in the boot policy. A server can boot with UEFI Secure Boot with or without a TPM 2.0 module. If it has a TPM, VMware vCenter can attest that the server booted with UEFI Secure Boot. Follow these steps:

1.     If your Cisco UCS servers have TPM 2.0 modules installed, TPM Attestation can be verified in the vSphere HTML5 Client.  To get to the HTML5 client from the Web Client, click “Launch vSphere Client (HTML5) in the upper center portion of the Web Client window.

2.     From the Hosts and Clusters window in the vSphere Client, select the vCenter. In the center pane, select Monitor > Security. The Attestation status will appear as shown below:

Cisco UCS Manager Plug-in for VMware vSphere Web Client

The Cisco UCS Manager Plug-in for VMware vSphere Web Client allows administration of UCS domains through the VMware vCenter administrative interface.  The capabilities of the plug-in include:

·       View Cisco UCS physical hierarchy

·       View inventory, installed firmware, faults, power and temperature statistics

·       Map the ESXi host to the physical server

·       Manage firmware for Cisco UCS B and C-Series Servers

·       View VIF paths for servers

·       Launch the Cisco UCS Manager GUI

·       Launch the KVM consoles of Cisco UCS Servers

·       Switch the existing state of the locator LEDs

The installation is only valid for VMware vCenter 5.5 or higher and will require revisions of .NET Framework 4.5 and VMware PowerCLI 5.1 or greater.

Cisco UCS Manager Plug-in Installation

To begin the plug-in installation on a Windows system that meets the previously stated requirements, follow these steps:

1.     Download the plugin and registration tool from: https://software.cisco.com/download/home/286282669/type/286282010/release/2.0.5?catid=282558030.

2.     Place the downloaded ucs-vcplugin-2.0.5.zip file onto the web server used for hosting the ONTAP software and VMware ESXi ISO.

3.     Unzip the Cisco_UCS_Plugin_Registration_Tool_1.2.2.zip and open the executable file within it.

4.     Leave Register Plugin selected for the Action, fill in the following vCenter information and click Submit:

a.     IP/Hostname

b.     Username

c.     Password

d.     URL that plugin has been uploaded to

 

5.     A pop-up will appear explaining that ‘allowHttp=true’ will need to be added to the webclient.properties file on the VCSA in the /etc/vmware/vsphere-client directory.

 

6.     This issue can be taken care of after the plugin has been registered, click OK to close the Information dialogue box.

7.     Click OK to confirm that the Cisco UCS Plugin registered successfully.

8.     To resolve the change needed for the HTTP download of the vSphere Web Client launch, connect to the VCSA with ssh using the root account, open the BASH shell, and type:

echo ‘allowHttp=true’ >> /etc/vmware/vsphere-client/webclient.properties

9.     Reboot the VCSA.

FlexPod UCS Domain Registration

Registration of the FlexPod UCS Domain can now be performed. The account used will correlate to the permissions allowed to the plugin, admin will be used in our example, but a read only account could be used with the plugin if that was appropriate for the environment.

To register the UCS Domain, follow these steps:

1.     Open the vSphere Web Client.

2.     Select the Home from the Navigator or drop-down list and select the Cisco UCS icon appearing in the Administration section.

3.     Click the Register button and provide the following options in the Register UCS Domain dialogue box that appears:

a.     UCS Hostname/IP

b.     Username

c.     Password

d.     Port (if different than 443)

e.     Leave SSL selected and click the Visible to All users option

 

4.     Click OK then click OK again to register the UCS Domain.

Register the Proactive High Availability Provider for Cisco UCS (Optional)

Cisco UCS Provider for Proactive high availability feature allows the system to assess the health of the server running the ESXi host. It assesses if the server is healthy, moderately or severely degraded. Any fault which occurs from the Cisco approved predefined list of faults with critical or major severity is reported to the vCenter.

To register the proactive HA provider for Cisco UCS, follow these steps:

1.     From the Cisco UCS Management Center page in the vSphere Web Client, select the Proactive HA Registration tab.

2.     Enter administrator@vsphere.local and the associated password. Click Register.

3.     Click OK to confirm registration.

4.     Enable the Proactive HA Provider for Cisco UCS by selecting Hosts and Clusters > FlexPod-Management > Configure > vSphere Availability in the vSphere Web Client. Select Turn on Proactive HA.

5.     In the list on the left, select Proactive HA Failures and Responses.

6.     Select the Automated Automation Level, Mixed Mode Remediation and the checkbox next to Cisco UCS Provider. Click OK.

Use the Cisco UCS vCenter Plugin

The plugin can now enable the functions described at the start of this section by double-clicking the registered UCS Domain under the Home tab in the Cisco UCS Management Center:

 

You can view the components associated to the domain:

Selecting within the chassis or rack mounts will provide a list of ESXi or non-ESXi servers to perform operations on the following:

 

In addition to viewing and working within objects shown in the UCS Plugin’s view of the UCS Domain, direct access of UCS functions provided by the plugin can be selected within the drop-down list of hosts registered to vCenter:

For detailed installation instructions and usage information, please refer to the Cisco UCS Manager Plug-in for VMware vSphere Web Client User Guide: http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/vmware_tools/vCenter/vCenter_Plugin_User_Guide/2x/b_vCenter_2x.html.

NetApp Virtual Storage Console 9.6 Deployment Procedure

This section describes the deployment procedures for the NetApp Virtual Storage Console (VSC).

Virtual Storage Console 9.6 Pre-installation Considerations

The following licenses are required for VSC on storage systems that run ONTAP 9.6:

·       Protocol licenses (NFS)

·       NetApp FlexClone® (for provisioning and cloning only)

·       NetApp SnapRestore® (for backup and recovery)

·       The NetApp SnapManager® Suite

The requirements for deploying VSC are listed here.

Install Virtual Storage Console 9.6

To install the VSC 9.6 software by using an Open Virtualization Format (OVF) deployment, follow these steps:

1.     Go to vSphere HTML5 Client > Host Cluster > Deploy OVF Template.

2.     Browse to the VSC OVA file downloaded from the NetApp Support site.

3.     Enter the VM name and select a datacenter or folder in which to deploy. Click NEXT.

4.     Select a host cluster resource in which to deploy OVA. Click NEXT.

5.     Review the details and accept the license agreement.

6.     Select Storage (infra_datastore – Thin Provision).

7.     From Select Networks, choose a destination network (IB-MGMT – vDS0) and click NEXT.

8.     From Customize Template, enter the VSC administrator password, vCenter name or IP address and other configuration details and click NEXT.   

9.     Review the configuration details entered and click FINISH to complete the deployment of NetApp-VSC VM.

10.  Power on the NetApp-VSC VM and open the VM console.

11.  During the NetApp-VSC VM boot process, you see a prompt to install VMware Tools. From vCenter, select NetApp-VSC VM > Guest OS > Install VMware Tools.

12.  Networking configuration and vCenter registration information was provided during the OVF template customization, therefore after NetApp-VSC VM is running, VSC, vSphere API for Storage Awareness (VASA), and VMware Storage Replication Adapter (SRA) are registered with vCenter.

13.  From the Home screen, confirm that the NetApp VSC is installed.

 

Download the NetApp NFS VAAI Plug-In

To download the NetApp NFS VAAI Plug-In, follow this step:

1.     Download the NetApp NFS Plug-In 1.1.2 for VMware .vib file from the NFS Plugin Download  page and save it to your local machine or admin host.

Install the NetApp NFS VAAI Plug-In

To install the NetApp NFS VAAI plug-in, follow these steps:

1.     Rename the .vib file that you downloaded from the NetApp Support Site to NetAppNasPlugin.vib to match the predefined name that VSC uses.

2.     Click Settings in the VSC home page.

3.     Click NFS VAAI Tools tab.

4.     Click Change in the Existing version section.

5.     Browse and select the renamed .vib file, and then click Upload to upload the file to the virtual appliance.

6.     In the Install on ESXi Hosts section, select the ESXi host on which you want to install the NFS VAAI plug-in, and then click Install.

7.     Reboot the ESXi host after the installation finishes.

Enable the VASA Provider

To enable the VASA provider, follow these steps:

1.     From the vSphere Client, click Menu > Virtual Storage Console.

2.     Click Settings.

3.     Click Manage Capabilities in the Administrative Settings tab.

4.     In the Manage Capabilities dialog box, select the VASA Provider extension to enable.

5.     Enter the IP address of the virtual appliance for VSC, VASA Provider, and SRA and the administrator password, and then click Apply.

Discover and Add Storage Resources

To Add storage resources for the Monitoring and Host Configuration capability and the Provisioning and Cloning capability, follow these steps:

1.     Using the vSphere web client, log in to the vCenter Server as the FlexPod admin user. If the vSphere web client was previously opened, close it and then reopen it.

2.     In the Home screen, click the Home tab and click Virtual Storage Console.

3.     Select Storage Systems >Add

4.     Click Overview > Getting Started, and then click ADD button under Add Storage System.

5.     Specify the vCenter Server instance where the storage will be located.

6.     In the IP Address/Hostname field, enter the storage cluster management IP.

7.      Confirm Port 443 to Connect to this storage system.

8.     Enter admin for the user name and the admin password for password.

9.     Click Save to add the storage configuration to VSC.

10.  Wait for the Storage Systems to update. You might need to click Refresh to complete this update.

To Discover the cluster and SVMs with the cluster admin account, follow these steps:

1.     From the vSphere Client Home page, select Hosts and Clusters.

2.     From the Actions menu of required datacenter, select NetApp VSC > Update Host and Storage Data. 

3.     VSC displays a Confirm dialog box that informs you that this operation might take a few minutes.

4.     Click OK.

Optimal Storage Settings for ESXi Hosts

VSC enables the automated configuration of storage-related settings for all ESXi hosts that are connected to NetApp storage controllers. To use these settings, follow these steps:

1.     From the VMware vSphere Web Client Home page, click vCenter > Hosts. 

2.     Select a host, and then select Actions > NetApp VSC > Set Recommended Values. 

3.     In the NetApp Recommended Settings dialog box, select all the values for your system. 

4.     Click OK.

  

Virtual Storage Console 9.6 Provisioning Datastores

Using VSC, the administrator can provision an NFS, FC or iSCSI datastore and attach it to a single host or multiple hosts in the cluster. The following steps describe provisioning a datastore and attaching it to the cluster.

Storage Capabilities

A storage capability is a set of storage system attributes that identifies a specific level of storage performance (storage service level), storage efficiency, and other capabilities such as encryption for the storage object that is associated with the storage capability. Use the default storage capabilities.

Provision NFS Datastore

To provision the NFS datastore, follow these steps:

1.     From the Virtual Storage Console Home page,  click Overview

2.     In the Getting Started Tab , Click Provision Button.

3.     Click Browse to select the destination to provision the datastore as per the next step.

4.     Select the type as NFS and Enter the datastore name.

5.     Provide the size of the datastore and the NFS Protocol.

6.     Check the storage capability profile and click Next

7.     Select the Storage Capability Profile, cluster name and the desired SVM to create the datastore. In this example, the Infra-SVM is selected.

8.     Click Next.

9.     Select the aggregate name and Click Next.

 

10.  Review the Summary and click Finish.

Provision FC Datastore

To provision the FC datastore, follow these steps:

1.     From the Virtual Storage Console Home page,  click Overview

2.     In the Getting Started Tab , Click Provision Button.

3.     Click Browse to select the destination to provision the datastore as per the next step.

4.     Select the type as VMFS and Enter the datastore name.

5.     Provide the size of the datastore and the FC Protocol.

6.     Check the storage capability profile and click Next

7.     Select the Storage Capability Profile, cluster name and the desired SVM to create the datastore. In this example, the Infra-SVM is selected.

8.     Click Next.

 

9.     Select the aggregate name and click Next.

 

10.  Review the Summary and click Finish.

 

11.   Click Ok.

NetApp SnapCenter 4.2

SnapCenter Software is a simple, centralized, scalable platform that provides application-consistent data protection for applications, databases, host file systems, and VMs running on ONTAP systems anywhere in the Hybrid Cloud.

Deploy NetApp SnapCenter

The SnapCenter platform is based on a multitier architecture that includes a centralized management server (SnapCenter Server) and a SnapCenter host agent. Snap Center Plug-in for VMware vSphere is packaged as a Linux Appliance (Debian-based Open Virtual Appliance format) and will no longer be part of the SnapCenter Plug-ins Package for Windows. The new virtual appliance is called NetApp Data Broker.

You need to install SnapCenter Server and the necessary plug-ins to support application-consistent backups. The NetApp Data Broker, SnapCenter Plug-in for VMware vSphere, documentation has more information.

·       Deployment Guide for SnapCenter Plug-in for VMware vSphere

·       Data Protection Guide for VMs, Datastores, and VMDKs using the SnapCenter Plug-in for VMware vSphere

SnapCenter Server Requirements

Table 8  lists the minimum requirements for installing SnapCenter Server and the SnapCenter plug-in on a Windows server. For the latest version compatibility and other plug-in information, refer to the NetApp Interoperability Matrix Tool.

See the SnapCenter 4.2 Installation and Setup Guide for the complete documentation.

Table 8     SnapCenter Server Requirements

Table 9    Port Requirements

SnapCenter 4.2 License Requirements

The following licenses are required for SnapCenter on storage systems that run ONTAP 9.6. These licenses do not need to be added into the SnapCenter GUI:

·       SnapCenter Standard controller-based licenses

·       Protocol licenses (NFS, FCP, or iSCSI as per protocol selection for deployment)

·       NetApp FlexClone (for provisioning and cloning only)

·       NetApp SnapRestore (for backup and recovery)

·       The NetApp SnapManager Suite

SnapCenter Server

The SnapCenter Server includes a web server, a centralized HTML5-based user interface, PowerShell cmdlets, APIs, and the SnapCenter repository. SnapCenter enables load balancing, high availability, and horizontal scaling across multiple SnapCenter Servers within a single user interface. You can accomplish high availability by using network load balancing (NLB) and Application Request Routing (ARR) with SnapCenter. For larger environments with thousands of hosts, adding multiple SnapCenterServers can help balance the load.

SnapCenter Plug-In for VMware vSphere

For SnapCenter 4.2 and later, the SnapCenter Plug-in for VMware vSphere is deployed as part of the NetApp Data Broker virtual appliance Linux-based VM. It provides a vSphere web client GUI on vCenter to protect VMware virtual machines (VMs) and datastores and supports SnapCenter application-specific plug-ins in protecting virtualized databases on primary and secondary storage.

Support for Virtualized Databases and File Systems

The Plug-in for VMware vSphere provides native backup, recovery, and cloning of virtualized applications (virtualized SQL and Oracle databases and Windows file systems) when using the SnapCenter GUI. 

SnapCenter natively leverages the Plug-in for VMware vSphere for all SQL, Oracle, and Windows file system data protection operations on VM disks (VMDKs), raw device mappings (RDMs), and NFS datastores.

SnapCenter Installation

To install SnapCenter, follow these steps. However, before you install SnapCenter, the SnapCenter Server host system must be up-to-date with Windows updates and no pending system restarts.

1.     Download the SnapCenter Server installation package from NetApp Support Site.

NetApp Downloads: SnapCenter Software

2.     Initiate the SnapCenter Server installation by double-clicking the downloaded .exe file.

After you initiate the installation, all the prechecks are performed and if the minimum requirements are not met appropriate error or warning messages are displayed.

You can ignore the warning messages and proceed with installation; however, errors should be fixed.

3.     Review the pre-populated values required for the SnapCenter Server installation and modify if required.

You do not have to specify the password for MySQL Server repository database. During SnapCenter Server installation the password is auto generated.

4.     Click Install Now.

SnapCenter Configuration

The default GUI URL is a secure connection to the default port 8146 on the server where the SnapCenter Server is installed (https://server:8146). If you provided a different server port during the SnapCenter installation, that port is used instead.

For NLB deployment, you must access SnapCenter using the NLB cluster IP (https://NLB_Cluster_IP:8146). If you do not see the SnapCenter UI when you navigate to https://NLB_Cluster_IP:8146 in IE, you must add the NLB IP address as a trusted site in IE on each plug-in host, or you must disable IE Enhanced Security on each plug-in host.

Add a User or Group to a Role

To add a user or group to a role, follow these steps:

1.     In the left navigation pane, click Settings.

2.     In the Settings page, click <Users and Access >.

3.     Select Domain or Workgroup as the Access type. For Domain authentication type, you should specify the domain name of the user or group to which you want to add the user to a role.

4.     Select User/Group for Type and add the User Name.  Repeat this step to add additional users or groups to the selected role.

5.     Select the role to which add the user.

6.     Click Assign and add assets to the user.

7.     Click Submit.

Configure Storage System Connections

To perform data protection and provisioning operations with SnapCenter, you must first set up the storage system connections that give SnapCenter access to ONTAP storage. Storage systems can also be added thru SnapCenter Plugin for vCenter. Both methods require the same set of information.

To add storage systems in SnapCenter GUI, follow these steps:

1.     Select Storage Systems -> Add

2.     Provide Storage system IP/FQDN and credentials.

3.     Check all event management options.

4.     Click Submit.

Install SnapCenter Plug-In for VMware

NetApp Data Broker is a linux-based virtual appliance (Open Virtual Appliance format) which enables the SnapCenter Plug-in for VMware vSphere.

Host and Privilege Requirements for the NetApp Data Broker

Review the following requirements before you install the NetApp Data Broker virtual appliance for SnapCenter Plug-in for VMware vSphere:

·       You must deploy the NetApp Data Broker virtual appliance as a Linux VM.

·       You should deploy the virtual appliance on the vCenter Server.

·       You must not deploy the virtual appliance in a folder that has a name with special characters.

·       You must deploy and register a separate, unique instance of the virtual appliance for each vCenter Server.

Table 10      Port Requirements

Download and Deploy the NetApp Data Broker OVA (Open Virtual Appliance)

To download and deploy the NetApp Data Broker OVA, follow these steps:

1.     Download NetApp Data Broker for VMware vSphere .ova file from Netapp support site (https://mysupport.netapp.com).

2.     From the VMware VCenter, VMs and Templates Tab, In Actions> Deploy OVF Template.

3.     Specify the location of the OVF Template and Click Next.

4.     On the Select a name and folder page, enter a unique name for the VM or vApp, and select a deployment location, and then click Next.

5.     On the Select a compute resource page, select a resource where you want to run the deployed VM template, and click Next.

6.     On the Review details page, verify the .ova template details and click Next.

7.     On the License agreements page, select the checkbox for I accept all license agreements.

8.     On the Select storage page, define where and how to store the files for the deployed OVF template:

a.     Select the disk format for the VMDKs.

b.     Select a VM Storage Policy.

c.     Select a datastore to store the deployed OVA template.

9.     On the Select networks page, select a source network and map it to a destination network, and then click Next.

10.  On the Customize template page, do the following:

a.     In Register to existing vCenter, enter the vCenter credentials.

b.     In Create NetApp Data Broker credentials, enter the NetApp Data Broker credentials.

c.     In Setup Network Properties, enter the network information.

d.     In Setup Date and Time, select the time zone where the vCenter is located.

11.  On the Ready to complete page, review the page and click Finish.

12.  Navigate to the VM where the virtual appliance was deployed, then click the Summary tab, and then click the Power On box to start the virtual appliance.

13.  While the virtual appliance is powering on, right-click the deployed virtual appliance and then click Install VMware tools.

14.  Log in to NetApp Data Broker using the IP address displayed on the deployment screen and the credentials that you provided in the deployment wizard, then verify on the Dashboard that the virtual appliance is successfully connected to vCenter and the SnapCenter Plug-in for VMware vSphere is successfully enabled and connected.

15.  The maintenance console user name is set to “maint” and the password is set to “admin123” by default.

Create a Virtual Appliance Credential for Migrating Backups

For VM consistent or VM crash-consistent backups, or application-consistent backups of virtualized data, you must migrate those backups to the virtual appliance for SnapCenter Plug-in for VMware vSphere. Before migrating, you must add the virtual appliance credentials to Snap-Center Server.

To create a virtual appliance credential for migrating backups, follow these steps:

1.     In the left navigation pane of the SnapCenter GUI, click Settings.

2.     In the Settings page, click Credentials, and then click New to start the wizard.

3.     Enter the credential information:

 

Register the SnapCenter Plug-in for VMware vSphere with SnapCenter Server

If you want to perform application-over-VMDK workflows in SnapCenter (application-based protection workflows for virtualized databases and file systems), you must register the SnapCenter Plug-in for VMware vSphere virtual appliance with the SnapCenter Server.

To register the SnapCenter plug-in, follow these steps:

1.     In the SnapCenter GUI left navigation pane, click Hosts.

2.     Verify that the Managed Hosts tab is selected at the top.

3.     Click Add to start the wizard.

4.     On the Add Hosts dialog box, specify the host you want to add to the SnapCenter Server:

5.     Click Submit.
When the VM host is successfully added, it is displayed on the Managed Hosts tab.

6.     Provide the credential information that was created above.

Register the SnapCenter Plug-in for VMware vSphere with VMware Vcenter

To register the SnapCenter plug-in, follow these steps:

1.      In your browser, navigate to http://<Data Broker IP>:8144/register.html

2.     Provide the VCenter Server Information and Click on Register.

3.     You should see the message Registration successful.

SnapCenter Plug-in for VMware vSphere in VCenter Server

After you have successfully installed the Plug-in for VMware vSphere, to configure SnapCenter and make it ready to backup virtual machines, follow these steps:

1.     In your browser, navigate to VMware vSphere web client URL https://<vCenter Server>/vsphere-client/?csp.

2.     On the VMware vCenter Single Sign-On page, login.

3.     On the VMware vSphere web client page, click Home and select SnapCenter Plug-In for VMware vSphere to bring up the SnapCenter Plug-In for VMware GUI. It will take you to the SnapCenter Plug-In for VMware dashboard.

Add Storage Systems (SVM)

To add storage systems, follow these steps:

1.     Go to the Storage Systems tab.

2.     Click + Add Storage System to add an SVM.

3.     Enter vCenter, Storage System, user credentials, and other required information in following dialog box.

Create Backup Policies for Virtual Machines and Datastores

To create backup policies for VMs and datastores, follow these steps:

1.     In the left Navigator pane of the VMware vSphere web client, click Policies.

2.     On the Policies page, click + New Policy in the toolbar.

3.     On the New Backup Policy page, follow these steps:

a.     Enter the policy name and a description.

b.     Enter the backups to keep.

c.     From the Frequency drop-down list, select the backup frequency (hourly, daily, weekly, monthly, and on-demand only).

d.     Click Add.

4.     Create multiple policies as required for different sets of VMs or datastores.

Create Resource Groups

Resource groups are groups of virtual machine or datastores that are backed up together. A backup policy is associated with the resource group to back up the virtual machines and retain a certain number of backups as defined in the policy.

To create resource groups, follow these steps:

1.     In the left Navigator pane of the VMware vSphere web client, click Resource Groups and then click Create Resource Group. This is the easiest way to create a resource group. However, you can also create a resource group with one resource by performing one of the following steps:

a.     To create a resource group for one virtual machine, click VMs and Templates, right-click a virtual machine, select NetApp SnapCenter from the drop-down list, and then select Create Resource Group from the secondary drop-down list.

b.     To create a resource group for one datastore, click Storage, right-click a datastore, select NetApp SnapCenter from the drop-down list, and then select Create Resource Group from the secondary drop-down list.

2.     In the General Info & Notification page, enter the resource group name and complete the notification settings. Click Next.

3.     Select a datastore as a parent entity to create a resource group of virtual machines, and then select the virtual machines from the available list. Click Next.

4.     From the Spanning Disks options, select the Always Include all Spanning Datastores option.

5.     From the Policies options, select the policies (from those already created earlier) that you want to associate with the resource group. Click Next.

6.     From the Schedules options, select the schedule for backups for each selected policy. Click Next.

7.     Review the summary and click Finish to complete the creation of the resource group.

View Virtual Machine Backups and Restore from vCenter by Using SnapCenter Plug-In

View Backups

Backups of the resources included in the resource group occurs according to the schedule of the policies associated with the resource group. To view the backups associated with each schedule, follow these steps:

1.     Go to any virtual machine that has been added to Resource Group > More Objects > Backups. It shows all the backups for that resource.

2.     On the SnapCenter Plugin  for VMware vSphere  check-out the Dashboard.

3.     In the SnapCenter Plug-In for VMware vSphere, Click Resource Groups and select any resource group. In the right pane, the completed backups are displayed.

4.     An on-demand backup can also be created for any resource group by following these steps:

a.     Click the virtual machine or datastore resource > More Objects > Resource Groups. Select the Resource Group and click Actions. Select Run Now. This process triggers the backup of the resource group containing a particular resource.

Restore from vCenter by Using SnapCenter Plug-In

To restore from vCenter by using SnapCenter Plug-In, follow these steps:

1.     The Plug-In for VMware vSphere provides native backup, recovery, and cloning of virtualized applications. Go to vCenter Web Client GUI > Select a VM > right-click and select NetApp SnapCenter.

2.     Select a backup from which to restore. Click Next.

3.     From the Restore Scope drop-down list, select either Entire virtual machine to restore the virtual machine with all VMDKs, or select Particular Virtual Disk to restore the VMDK without affecting the virtual machine configuration and other VMDKs.

4.     Select the destination datastore. Click Next.

5.     Review the Summary and click Finish to complete the restore process.

Provision Virtual Volumes (VVols)

The NetApp vSphere APIs for Storage Awareness or VASA enables the vSphere Administrator to take advantage of the new capabilities for storage-based policy management and automation.  The NetApp VASA provider is used to provide automation for DevOps and private cloud deployments and enable the vSphere Administrator to provision storage for virtual machines based on pre-configured policies created by the Storage Administrator.  Specific storage types, performance, and storage efficiency characteristics for each storage tier in the environment can be expressed in a set of policies to ensure the appropriate type of storage is provisioned to the virtual machine every time. 

Verify NDMP Vserver Scope Mode

To verify the NDMP Vserver scope mode, follow these steps:

1.     View NDMP scope mode with the following command:

2.     Disable NDMP node-scoped mode.

3.     Enable NDMP services on the vserver.

OnCommand API Services for ONTAP VASA Provider

OnCommand API Services enables you to add storage systems running ONTAP, Cloud Volumes ONTAP, ONTAP Select to retrieve storage-related information, and to provision storage resources.

To configure API services to enable the VSC rich dashboard for Virtual Volumes, follow these steps:

Download the following packages before beginning the installation and upload them to the /tmp directory on a RHEL 7.5 or CentOS 7.5 host you will used as the API services host:

·       MySQL YUM Repository: https://dev.mysql.com/downloads/repo/yum

·       mysql80-community-release-el7-3.noarch.rpm

·       OnCommand API Services 2.2.0 binary

1.     Install a separate CentOS 7.5 VM.

2.     Open the required firewall ports with the following command:

3.     Download the Extra Package for Enterprise Linux (EPEL).

4.     Install the EPEL repository.

5.     Install the MySQL community edition repository.

6.     Remove any mariadb components.

7.     Set the executable bit on the OnCommand API Services binary.

8.     Edit the /etc/yum.repos.d/mysql-community.repo.  Locate the subrepository block and set enable=0 on mysql80-community, and enable=1 on mysql57-community.

9.     Install the MySQL 5.7 community server and additional libraries.

10.  Install OnCommand API Services 2.2.

11.  When OnCommand API services installation is complete record the URL for use to connect with the VSC.

12.  Navigate to the NetApp Virtual Storage Console from Home.

13.  Select Manage VASA Provider Extensions and enter the configuration information recorded from step 11

14.  Click Apply and notice that the API-Services registered successfully.

 

15.  Navigate back to the Summary option in the Navigator pane to display the VVOL dashboard

Create the Storage Capability Profile

In order to leverage the automation features of VASA and Virtual Volumes two primary components must first be configured.  The Storage Capability Profile (SCP) and the VM Storage Policy.  The Storage Capability Profile expresses a specific set of storage characteristics into one or more profiles used to when provisioning a Virtual Volume.  The SCP is specified as part of VM Storage Policy which is specified when you deploy a virtual machine.  NetApp Virtual Storage Console comes with Five pre-configured Storage Capability Profiles mapped to different storages types from FAS to AFF.  These storage profiles match the adaptive QoS policies in ONTAP 9.6.

To review or edit one of the built-in profiles pre-configured with VSC 7.2.1, follow these steps:

1.     In the NetApp Virtual Storage Console select Storage Capability Profiles.

2.     Select the Gold Storage Capability Profile and choose Update from the toolbar.

3.     Click number 4. Storage Attributes to edit the storage capabilities.

4.     Review the Storage Attributes and make any desired changes.

5.     Click Cancel or Finish if any changes were made.

Provision VVOL from Virtual Storage Console

To provision VVOL from Virtual Storage Console, follow these steps:

1.     Starting from Home > Hosts and Clusters.

2.     Select FlexPod-Management datacenter > Actions > Provision Datastore.

3.     Provide a name, a description for the volume, and choose NFS for the protocol.  Select Next.

4.     In the Storage System section Select the Gold Storage Capability Profile or another appropriate SCP for the target workload. Provide the Storage system and the Storage VM detail. Choose Next.

5.     In the Storage Attributes Section, select Create New Volume and provide the details.

6.     Review the details and click Finish.

Create Virtual Machine with Assigned VM Storage Policy

To create a virtual machine and assigned a VM storage policy, follow these steps:

1.     Navigate to the VMs and Templates tab and select the FlexPod-DC datacenter.

2.     Click Actions and select New Virtual Machine.

3.     Select Create a new virtual machine and choose Next.

4.     Enter a name for the VM and select the FlexPod-DC datacenter.

5.     Choose the FlexPod-Management Data compute Resource

6.     Select the VVOl Datastore for the storage and click Next.

7.     Select Compatibility and click Next.

8.     Select the Guest OS and click Next.

9.     Customize the hardware for the VM and click Next.

10.  Review the details and click Finish.

VSC VVOl Dashboard and Reports

To configure the VSC VVOL dashboard and reports, follow these steps:

1.     In the Virtual Storage Console-> Overview-> Click the VVol dashboard.

2.     In the VSC -> Reports -> click the VVOL Datastore reports.

3.     In the VSC-> Reports -> Click the VVol VM reports.

Active IQ Unified Manager 9.6

Active IQ Unified Manager (formerly OnCommand Unified Manager) enables you to monitor and manage the health and performance of your ONTAP storage systems from a single interface. Unified Manager provides a graphical interface that displays the capacity, availability, protection, and performance status of the monitored storage systems.

This section describes the steps to deploy NetApp Active IQ Unified Manager 9.6 on a CentOS Linux 7.6 virtual machine.  The following table lists the recommended configuration for the virtual machine to install and run Active IQ Unified Manager to ensure acceptable performance.

Table 11      Virtual Machine Configuration

To install Unified Manager 9.6, follow these steps:

1.     Download NetApp Active IQ Unified Manager for VMware vSphere .ova file from Netapp support site (https://mysupport.netapp.com).

2.     From the VMware VCenter, click the VMs and Templates Tab, then click In Actions> Deploy OVF Template.

3.     Specify the location of the OVF Template and click Next.

4.     On the Select a name and folder page, enter a unique name for the VM or vApp, and select a deployment location, and then click Next.

5.     On the Select a compute resource page, select a resource where you want to run the deployed VM template, and click Next.

6.     On the Review details page, verify the .ova template details and click Next.

7.     On the License agreements page, select the checkbox for I accept all license agreements.

8.     On the Select storage page, define where and how to store the files for the deployed OVF template.

a.     Select the disk format for the VMDKs.

b.     Select a VM Storage Policy.

c.     Select a datastore to store the deployed OVA template.

9.     On the Select networks page, select a source network and map it to a destination network, and then click Next.

10.  On the Customize template page, provide network details.

11.  On the Ready to complete page, review the page and click Finish.

12.  Navigate to the VM in the VMs and Templates Tab, then click the Summary tab, and then click the Power On box to start the virtual machine.

13.  While the virtual Machine is powering on, right-click the deployed virtual machine and then click Install VMware tools.

14.  Log into NetApp Active IQ UM using the IP address displayed on the deployment screen. Please use the credentials for the admin user or the maintenance user.

Configure Active IQ Unified Manager

To configure Active IQ Unified Manager and add a storage system for monitoring, follow these steps:

1.     Log into the web browser of Active IQ Unified Manger.

2.     Enter the email address that Unified Manager will use to send alerts, enter the mail server configuration, and the IP address or hostname of the NTP server.  Select Next and complete the AutoSupport configuration.

3.     Save and complete the configuration and continue to the next step.

Add Storage to Active IQ Unified Manager

To add storage to the Active IQ Unified Manager, follow these steps:

1.     Click Add on the Configuration/Cluster Data Sources screen to add the storage cluster.

2.     Enter the hostname and login credentials to the storage cluster.

3.     When prompted to trust the self-signed certificate from Active IQ Unified Manager, select Yes to finish and add the storage system.  The initial discovery process can take up to 15 minutes to complete.

Provision a Sample Application Tenant

This section describes a sample procedure for provisioning an application tenant. The procedure refers to previous sections of this document and can be used as a guide and modified as needed when provisioning an application tenant.

1.     Plan your application tenant and determine what storage protocols will be provided in the tenant.  In the architecture explained in this document, fibre channel, NFS, iSCSI, and CIFS/SMB (CIFS/SMB have not been discussed in this document) can be provided to the tenant.  Also, plan what network VLANs the tenant will use.  It is recommended to have a VLAN for virtual machine management traffic.  One or two VLANs (iSCSI needs two if VMware RDM LUNs or iSCSI datastores will be provisioned) are also needed for each storage protocol used except fibre channel.  Fibre channel will have new storage LIFs defined with the same VSANs configured for the FlexPod Infrastructure.

2.     In the Nexus switches, declare all added VLANs and configure the VM VLAN as an allowed VLAN on the UCS port channels and the vPC peer link.  Also, Layer 3 with HSRP or VRRP can be configured in the Nexus switches to provide this VLAN access to the outside.  Layer 3 setup is not explained in this document but is explained in the Nexus 9000 documentation. Configure the storage VLANs on the UCS and storage port channels, and on the vPC peer link. The VM VLAN can also be added to the storage port channels in order to configure the tenant SVM management interface on this VLAN.

3.     In the storage cluster:

a.     Create a broadcast domain with MTU 1500 for the tenant SVM management interface. Create a broadcast domain with MTU 9000 for each tenant storage protocol except fibre channel.

b.     Create VLAN interface ports on the node interface group on each node for tenant SVM management (VM VLAN) and for the VLAN for each storage protocol except fibre channel.  Add these VLAN ports to the appropriate broadcast domains.

c.     Create the tenant SVM and follow all procedures in that section.

d.     Create Load-Sharing Mirrors for the tenant SVM.

e.     Create the FC or iSCSI service for the tenant SVM if fibre channel or iSCSI is being deployed in this tenant.

f.      Optionally, create a self-signed security certificate for the tenant SVM.

g.     Configure NFSv3 for the tenant SVM.

h.     Create a VM datastore volume in the tenant SVM.

i.       If fibre channel is being deployed in this tenant, configure four FCP LIFs in the tenant SVM on the same fibre channel ports as in the Infrastructure SVM.

j.       If iSCSI is being deployed in this tenant, configure four iSCSI LIFs in the tenant SVM on the iSCSI VLAN interfaces.

k.     Create an NFS LIF in the tenant SVM on each storage node.

l.       Create a boot LUN in the esxi_boot volume in the Infra-SVM for each tenant VMware ESXi host.

m.    Add the tenant SVM Administrator, SVM management LIF on the SVM management VLAN port, and default route for the SVM.

4.     In Cisco UCS, one method of tenant setup is to dedicate a VMware ESXi cluster and set of UCS servers to each tenant.  Service profiles will be generated for at least two tenant ESXi hosts.  These hosts can boot from LUNs from the esxi_boot volume in the Infra-SVM but will also have access to FC storage in the tenant SVM.

a.     Create a Server Pool for the tenant ESXi host servers.

b.     Create all tenant VLANs in the LAN Cloud.

c.     Add the tenant VLANs to the vDS vNIC templates. 

d.     Generate service profiles from the service profile template with the vMedia policy for the tenant ESXi hosts.  Remember to bind these service profiles to the service profile template without the vMedia policy after VMware ESXi installation.

5.     In the Cisco MDS 9132T switches:

a.     Create device aliases for the tenant ESXi host vHBAs and the FC LIFs in the tenant storage SVM.

b.     Create zones for the tenant ESXi hosts with fibre channel targets from both the storage Infra-SVM and the tenant SVM. 

c.     Add these zones to the Fabric zoneset and activate the zoneset.

6.     In the storage cluster:

a.     Create igroups for the tenant ESXi hosts in both the Infra-SVM and tenant SVM.  Also, create an igroup in the tenant SVM that includes the WWPNs for all tenant ESXi hosts to support shared storage from the tenant SVM.

b.     In Infra-SVM, map the boot LUNs created earlier to the tenant ESXi hosts.  Tenant FC or iSCSI storage can be created later using NetApp VSC.

7.     Install and configure VMware ESXi on all tenant host servers. It is not necessary to map infra_datastore unless you want the tenant ESXi hosts to have access to VMs or VM templates in these datastores.

8.     In VMware vCenter, create a cluster for the tenant ESXi hosts.  Add the hosts to the cluster.

9.     Using the vCenter Web Client, add the tenant hosts to vDS0 or create a tenant vDS and add the hosts to it. In vDS0, add port-profiles for the tenant VLANs. When migrating the hosts to the vDS, leave only the ESXi management interfaces on vSwitch0.

10.  Back in vCenter, add in any necessary VMkernel ports for storage interfaces remembering to set the MTU correctly on these interfaces.  Mount the tenant NFS datastore on the tenant cluster if one was created. Tenant iSCSI VMkernel ports can be created on the vDS with the port groups pinned to the appropriate fabric.

11.  Using the NetApp VSC plugin to the vCenter Web Client, set recommended values for all tenant ESXi hosts.  Ensure the NetApp NFS Plug-in for VMware VAAI is installed on all tenant hosts and reboot each host.

12.  You can now begin provisioning virtual machines on the tenant cluster.  The NetApp VSC plugin can be used to provision fibre channel, iSCSI, and NFS datastores.

13.  Optionally, use NetApp SnapCenter to provision backups of tenant virtual machines.

FlexPod iSCSI Addition

Cisco Nexus Switch Configuration

This section is a delta section for adding infrastructure iSCSI to the Nexus switches.  This section should be executed after the Cisco Nexus Switch Configuration section in the main document is completed.

Create Infrastructure iSCSI VLANs on Cisco Nexus A and Cisco Nexus B

To create the necessary virtual local area networks (VLANs), follow this step on both switches:

1.     From the global configuration mode, run the following commands:

Add Infrastructure iSCSI VLANs to Port-Channels on Cisco Nexus A and Cisco Nexus B

To create the necessary virtual local area networks (VLANs), follow this step on both switches:

1.     From the global configuration mode, run the following commands:

NetApp Storage Configuration – Part 1

When using the iSCSI protocol for SAN boot connectivity, use the Storage Configuration steps outlined in the body of this document.  Where appropriate, replace the Fibre Channel configuration steps with the steps listed here.

Create Block Protocol (iSCSI) Service

1.     Remove FCP protocol from the vserver.

2.     Enable the iSCSI protocol on the vserver.

3.     Create the iSCSI block service.

Create iSCSI Broadcast Domains

To create the broadcast domains for each of the iSCSI VLANs, run the following commands:

Create iSCSI VLANs

To create iSCSI VLANs, follow these steps:

1.     Modify the MTU size on the parent interface group hosting the iSCSI traffic using the following commands:

2.     Create VLAN ports for the iSCSI LIFs on each storage controller.

Add VLANs to iSCSI Broadcast Domains

To add each of the iSCSI VLAN ports to the corresponding broadcast domain, run the following commands:

Create iSCSI LIFs

To create four iSCSI LIFs, run the following commands (two on each node):

Cisco UCS iSCSI Configuration

The following subsections can be completed to add infrastructure iSCSI to the Cisco UCS.  These subsections can be completed in place of the subsections in the Cisco UCS Configuration section of this document labeled (FCP), or they can be completed in addition to the FCP sections to have the option of FCP or iSCSI boot.

Create IQN Pools for iSCSI Boot

To configure the necessary IQN pools for the Cisco UCS environment, follow these steps:

1.     In Cisco UCS Manager, click SAN.

2.     Expand Pools > root.

3.     Right-click IQN Pools.

4.     Select Create IQN Suffix Pool to create the IQN pool.

5.     Enter IQN-Pool for the name of the IQN pool.

6.     Optional: Enter a description for the IQN pool.

7.     Enter iqn.2010-11.com.flexpod as the prefix.

8.     Select Sequential for Assignment Order.

9.     Click Next.

10.  Click Add.

11.  Enter ucs-host as the suffix.

12.  Enter 1 in the From field.

13.  Specify the size of the IQN block sufficient to support the available server resources.

14.  Click OK.

15.  Click Finish and OK to complete creating the IQN pool.

Create IP Pools for iSCSI Boot

To configure the necessary IP pools for iSCSI boot for the Cisco UCS environment, follow these steps:

1.     In Cisco UCS Manager, click LAN.

2.     Expand Pools > root.

3.     Right-click IP Pools.

4.     Select Create IP Pool.

5.     Enter iSCSI-IP-Pool-A as the name of IP pool.

6.     Optional: Enter a description for the IP pool.

7.     Select Sequential for the assignment order.

8.     Click Next.

9.     Click Add to add a block of IP addresses.

10.  In the From field, enter the beginning of the range to assign as iSCSI boot IP addresses on Fabric A.

11.  Set the size to enough addresses to accommodate the servers.

12.  Enter the appropriate Subnet Mask.

13.  Click OK.

14.  Click Next.

15.  Click Finish and OK to complete creating the Fabric A iSCSI IP Pool.

16.  Right-click IP Pools.

17.  Select Create IP Pool.

18.  Enter iSCSI-IP-Pool-B as the name of IP pool.

19.  Optional: Enter a description for the IP pool.

20.  Select Sequential for the assignment order.

21.  Click Next.

22.  Click Add to add a block of IP addresses.

23.  In the From field, enter the beginning of the range to assign as iSCSI IP addresses on Fabric B.

24.  Set the size to enough addresses to accommodate the servers.

25.  Enter the appropriate Subnet Mask.

26.  Click OK.

27.  Click Next.

28.  Click Finish and OK to complete creating the Fabric B iSCSI IP Pool.

Create iSCSI VLANs

To configure the necessary iSCSI virtual local area networks (VLANs) for the Cisco UCS environment, follow these steps:

1.     In Cisco UCS Manager, click LAN.         

2.     Expand LAN > LAN Cloud.        

3.     Right-click VLANs.

4.     Select Create VLANs.

5.     Enter Infra-iSCSI-A as the name of the VLAN to be used for iSCSI-A.

6.     Keep the Common/Global option selected for the scope of the VLAN.

7.     Enter the Infra-iSCSI-A VLAN ID.

8.     Keep the Sharing Type as None.

9.     Click OK and then click OK again.

10.  Right-click VLANs.

11.  Select Create VLANs.

12.  Enter Infra-iSCSI-B as the name of the VLAN to be used for iSCSI-B.

13.  Keep the Common/Global option selected for the scope of the VLAN.

14.  Enter the iSCSI-B VLAN ID.

15.  Keep the Sharing Type as None.

16.  Click OK and then click OK again.

Create iSCSI vNIC Templates

To create iSCSI virtual network interface card (vNIC) templates for the Cisco UCS environment within the FlexPod Organization, follow these steps:

1.     Select LAN.

2.     Expand Policies > root > Sub-Organizations > FlexPod Organization.

3.     Right-click vNIC Templates under the FlexPod Organization.

4.     Select Create vNIC Template.

5.     Enter iSCSI-Template-A as the vNIC template name.

6.     Select Fabric A. Do not select the Enable Failover checkbox.

7.     Leave Redundancy Type set at No Redundancy.

8.     Under Target, make sure that only the Adapter checkbox is selected.

9.     Select Updating Template for Template Type.

10.  Under VLANs, select only Infra-iSCSI-A.

11.  Select Infra-iSCSI-A as the native VLAN.

12.  Leave vNIC Name set for the CDN Source.

13.  Under MTU, enter 9000.

14.  From the MAC Pool list, select MAC-Pool-A.

15.  From the Network Control Policy list, select Enable-CDP-LLDP.

16.  Click OK to complete creating the vNIC template.

17.  Click OK.

18.  Right-click vNIC Templates.

19.  Select Create vNIC Template.

20.  Enter iSCSI-Template-B as the vNIC template name.

21.  Select Fabric B. Do not select the Enable Failover checkbox.

22.  Leave Redundancy Type set at No Redundancy.

23.  Under Target, make sure that only the Adapter checkbox is selected.

24.  Select Updating Template for Template Type.

25.  Under VLANs, select only Infra-iSCSI-B.

26.  Select Infra-iSCSI-B as the native VLAN.

27.  Leave vNIC Name set for the CDN Source.

28.  Under MTU, enter 9000.

29.  From the MAC Pool list, select MAC-Pool-B.

30.  From the Network Control Policy list, select Enable-CDP-LLDP.

31.  Click OK to complete creating the vNIC template.

32.  Click OK.

Create LAN Connectivity Policy for iSCSI Boot

To configure the necessary Infrastructure LAN Connectivity Policy within the FlexPod Organization, follow these steps:

1.     In Cisco UCS Manager, click LAN.

2.     Expand LAN > Policies > root > Sub-Organizations > FlexPod Organization.

3.     Right-click LAN Connectivity Policies under the FlexPod Organization.

4.     Select Create LAN Connectivity Policy.

5.     Enter iSCSI-Boot as the name of the policy.

6.     Click the upper Add button to add a vNIC.

7.     In the Create vNIC dialog box, enter 00-vSwitch0-A as the name of the vNIC.

8.     Select the Use vNIC Template checkbox.

9.     In the vNIC Template list, select vSwitch0-A.

10.  In the Adapter Policy list, select VMWare.

11.  Click OK to add this vNIC to the policy.

12.  Click the upper Add button to add another vNIC to the policy.

13.  In the Create vNIC box, enter 01-vSwitch0-B as the name of the vNIC.

14.  Select the Use vNIC Template checkbox.

15.  In the vNIC Template list, select vSwitch0-B.

16.  In the Adapter Policy list, select VMWare.

17.  Click OK to add the vNIC to the policy.

18.  Click the upper Add button to add a vNIC.

19.  In the Create vNIC dialog box, enter 02-vDS0-A as the name of the vNIC.

20.  Select the Use vNIC Template checkbox.

21.  In the vNIC Template list, select vDS0-A.

22.  In the Adapter Policy list, select VMWare.

23.  Click OK to add this vNIC to the policy.

24.  Click the upper Add button to add another vNIC to the policy.

25.  In the Create vNIC box, enter 03-vDS0-B as the name of the vNIC.

26.  Select the Use vNIC Template checkbox.

27.  In the vNIC Template list, select vDS0-B.

28.  In the Adapter Policy list, select VMWare.

29.  Click OK to add the vNIC to the policy.

30.  Click the upper Add button to add a vNIC.

31.  In the Create vNIC dialog box, enter 04-iSCSI-A as the name of the vNIC.

32.  Select the Use vNIC Template checkbox.

33.  In the vNIC Template list, select iSCSI-Template-A.

34.  In the Adapter Policy list, select VMWare.

35.  Click OK to add this vNIC to the policy.

36.  Click Add to add a vNIC to the policy.

37.  In the Create vNIC dialog box, enter 05-iSCSI-B as the name of the vNIC.

38.  Select the Use vNIC Template checkbox.

39.  In the vNIC Template list, select iSCSI-Template-B.

40.  In the Adapter Policy list, select VMWare.

41.  Click OK to add this vNIC to the policy.

42.  Expand Add iSCSI vNICs.

43.  Select Add in the Add iSCSI vNICs section.

44.  Set the name to iSCSI-Boot-A.

45.  Select 04-iSCSI-A as the Overlay vNIC.

46.  Set the iSCSI Adapter Policy to default.

47.  Leave the VLAN set to Infra-iSCSI-A (native).

48.  Leave the MAC Address set to None.

49.  Click OK.

50.  Select Add in the Add iSCSI vNICs section.

51.  Set the name to iSCSI-Boot-B.

52.  Select 05-iSCSI-B as the Overlay vNIC.

53.  Set the iSCSI Adapter Policy to default.

54.  Leave the VLAN set to Infra-iSCSI-B (native).

55.  Leave the MAC Address set to None.

 

56.  Click OK, then click OK again to create the LAN Connectivity Policy.

Create iSCSI Boot Policy

This procedure applies to a Cisco UCS environment in which two iSCSI logical interfaces (LIFs) are on cluster node 1 (iscsi-lif01a and iscsi-lif01b) and two iSCSI LIFs are on cluster node 2 (iscsi-lif02a and iscsi-lif02b). Also, it is assumed that the A LIFs are connected to Fabric A (Cisco UCS Fabric Interconnect A) and the B LIFs are connected to Fabric B (Cisco UCS Fabric Interconnect B).

To create a boot policy for the Cisco UCS environment within the FlexPod Organization, follow these steps:

1.     In Cisco UCS Manager, click Servers.

2.     Expand Policies > root > Sub-Organizations > FlexPod Organization.

3.     Right-click Boot Policies under the FlexPod Organization.

4.     Select Create Boot Policy.

5.     Enter Boot-iSCSI-A as the name of the boot policy.

6.     Optional: Enter a description for the boot policy.

7.     Do not select the Reboot on Boot Order Change checkbox.

8.     Select the Legacy Boot Mode.

9.     Expand the Local Devices drop-down menu and select Add Remote CD/DVD.

10.  Expand the iSCSI vNICs drop-down menu and select Add iSCSI Boot.

11.  In the Add iSCSI Boot dialog box, enter iSCSI-Boot-A.

12.  Click OK.

13.  Select Add iSCSI Boot.

14.  In the Add iSCSI Boot dialog box, enter iSCSI-Boot-B.

15.  Click OK.

16.  Expand CIMC Mounted Media and select Add CIMC Mounted CD/DVD.

 

17.  Click OK then click OK again to create the policy.

Create iSCSI Boot Service Profile Template

In this procedure, one service profile template for Infrastructure ESXi hosts within the FlexPod Organization is created for Fabric A boot.

To create the service profile template, follow these steps:

1.     In Cisco UCS Manager, click Servers.

2.     Expand Service Profile Templates > root > Sub-Organizations > FlexPod Organization.

3.     Right-click the FlexPod Organization.

4.     Select Create Service Profile Template to open the Create Service Profile Template wizard.

5.     Enter VM-Host-Infra-iSCSI-A as the name of the service profile template. This service profile template is configured to boot from storage node 1 on fabric A.

6.     Select the “Updating Template” option.

7.     Under UUID Assignment, select UUID_Pool.

8.     Click Next.

Configure Storage Provisioning

To configure the storage provisioning, follow these steps:

1.     If you have servers with no physical disks, click on the Local Disk Configuration Policy tab and select the SAN-Boot Local Storage Policy. Otherwise, select the default Local Storage Policy.

2.     Click Next.

Configure Networking Options

To configure the network options, follow these steps:

1.     Keep the default setting for Dynamic vNIC Connection Policy.

2.     Select the “Use Connectivity Policy” option to configure the LAN connectivity.

3.     Select iSCSI-Boot from the LAN Connectivity Policy drop-down list.

4.     Select IQN_Pool in Initiator Name Assignment.

 

5.     Click Next.

Configure Storage Options

To configure the storage options, follow these steps:

1.     Select No vHBAs for the “How would you like to configure SAN connectivity?” field.

2.     Click Next.

Configure Zoning Options

To configure the zoning options, follow this step:

1.     Make no changes and click Next.

Configure vNIC/HBA Placement

To configure the vNIC/HBA placement, follow these steps:

1.     In the “Select Placement” list, leave the placement policy as “Let System Perform Placement”.

2.     Click Next.

Configure vMedia Policy

To configure the vMedia policy, follow these steps:

1.     Do not select a vMedia Policy.

2.     Click Next.

Configure Server Boot Order

To configure the server boot orders, follow these steps:

1.     Select Boot-iSCSI-A for Boot Policy.

2.     In the Boot order, expand iSCSI and select iSCSI-Boot-A.

3.     Click Set iSCSI Boot Parameters.

4.     In the Set iSCSI Boot Parameters pop-up, leave Authentication Profile to <not set> unless you have in-dependently created one appropriate to your environment.

5.     Leave the “Initiator Name Assignment” dialog box <not set> to use the single Service Profile Initiator Name defined in the previous steps.

6.     Set iSCSI-IP-Pool-A as the “Initiator IP address Policy.”

7.     Select iSCSI Static Target Interface option.

8.     Click Add.

9.     Enter the iSCSI Target Name. To get the iSCSI target name of Infra-SVM, log into the storage cluster management interface and run the “iscsi show” command”.

10.   Enter the IP address of iscsi-lif-2a for the IPv4 Address field.

 

11.  Click OK to add the iSCSI static target.

12.  Click Add.

13.  Enter the iSCSI Target Name.

14.  Enter the IP address of iscsi-lif-1a for the IPv4 Address field.

15.  Click OK to add the iSCSI static target.

 

16.  Click OK to complete setting the iSCSI Boot Parameters.

17.  In the Boot order, select iSCSI-Boot-B.

18.  Click Set iSCSI Boot Parameters.

19.  In the Set iSCSI Boot Parameters pop-up, leave Authentication Profile to <not set> unless you have in-dependently created one appropriate to your environment.

20.  Leave the “Initiator Name Assignment” dialog box <not set> to use the single Service Profile Initiator Name defined in the previous steps.

21.  Set iSCSI-IP-Pool-B as the “Initiator IP address Policy”.

22.  Select the iSCSI Static Target Interface option.

23.  Click Add.

24.  Enter the iSCSI Target Name. To get the iSCSI target name of Infra-SVM, login into storage cluster management interface and run “iscsi show” command”.

25.   Enter the IP address of iscsi-lif-2b for the IPv4 Address field.

26.   Click OK to add the iSCSI static target.

27.  Click Add.

28.  Enter the iSCSI Target Name.

29.  Enter the IP address of iscsi-lif-1b for the IPv4 Address field.

30.   Click OK to add the iSCSI static target.

 

31.  Click OK to complete setting the iSCSI Boot Parameters.

32.  Click Next.

Configure Maintenance Policy

To configure the maintenance policy, follow these steps:

1.     Change the Maintenance Policy to default.

2.     Click Next.

Configure Server Assignment

To configure server assignment, follow these steps:

1.     In the Pool Assignment list, select Infra-Pool.

2.     Select Down as the power state to be applied when the profile is associated with the server.

3.     Optional: select “UCS-B200-M5” for the Server Pool Qualification to select only B200 M5 servers in the pool.

4.     Expand Firmware Management at the bottom of the page and select the default policy.

 

5.     Click Next.

Configure Operational Policies

To configure the operational policies, follow these steps:

1.     In the BIOS Policy list, select VM-Host.

2.     Expand Power Control Policy Configuration and select No-Power-Cap in the Power Control Policy list.

  

3.     Click Finish to create the service profile template.

4.     Click OK in the confirmation message.

Create vMedia-Enabled Service Profile Template

To create a service profile template with vMedia enabled, follow these steps:

1.     Connect to Cisco UCS Manager and click Servers.

2.     Select Service Profile Templates > root > Sub-Organizations > FlexPod Organization > Service Template VM-Host-Infra-iSCSI-A.

3.     Right-click VM-Host-Infra-iSCSI-A and select Create a Clone.

4.     Name the clone VM-Host-Infra-iSCSI-A-vM and click OK then click OK again to create the clone.

5.     Select the newly-created VM-Host-Infra-iSCSI-A-vM and select the vMedia Policy tab.

6.     Click Modify vMedia Policy.

7.     Select the ESXi-6.7U2-HTTP vMedia Policy and click OK.

8.     Click OK to confirm.

Create Service Profiles

To create service profiles from the service profile template, follow these steps:

1.     Connect to Cisco UCS Manager and click Servers.

2.     Select Service Profile Templates > root > Sub-Organizations > FlexPod Organization > Service Template VM-Host-Infra-iSCSI-A-vM.

3.     Right-click VM-Host-Infra-iSCSI-A-vM and select Create Service Profiles from Template.

4.     Enter VM-Host-Infra-0 as the service profile prefix.

5.     Enter 1 as “Name Suffix Starting Number.”

6.     Enter 2 as the “Number of Instances.”

7.     Click OK to create the service profiles.

8.     Click OK in the confirmation message.

When VMware ESXi 6.7 U2 has been installed on the hosts, the host Service Profiles can be bound to the VM-Host-Infra-iSCSI-A Service Profile Template to remove the vMedia Mapping from the host.

NetApp Storage Configuration – Part 2

Create igroups

It is assumed that boot LUNs have already been created for the two ESXi management hosts.

Table 12      iSCSI IQN for SVM

Table 13      iSCSI vNIC IQN Configuration

Create igroups by entering the following commands from the storage cluster management LIF SSH connection:

To view the two igroups just created, use the command lun igroup show.

Map Boot LUNs to igroups

From the storage cluster management LIF SSH connection, run the following commands:

VMware vSphere Configuration

Set Up VMkernel Ports and Virtual Switch on ESXi Host VM-Host-Infra-01

To add the iSCSI networking configuration on the first ESXi host, follow the steps at the end of section Set Up VMkernel Ports and Virtual Switch. In this section, a single iSCSI Boot vSwitch is configured with two uplinks, one to UCS fabric A and the other to fabric B. The first VMkernel port will be mapped only to the fabric A uplink and the second one will be mapped to the fabric B uplink.

To setup Vmkernel ports and virtual switches on ESXi hosts on VM-Host-Infra-01, follow these steps:

1.     From the Host Client, select Networking.

2.     In the center pane, select the Virtual switches tab.

3.     Highlight the iScsiBootvSwitch line.

4.     Select Edit settings.

5.     Change the MTU to 9000.

6.     Select Add uplink to add an uplink to iScsiBootvSwitch.

7.     Use the pulldown to select vmnic5 for Uplink 2.

8.     Expand NIC teaming, select vmnic5, and select Mark standby.

9.     Click Save.

10.  Select the VMkernel NICs tab.

11.  Select the vmk1 iScsiBootPG line. Select Edit Settings to edit the properties of this VMkernel port.

12.  Change the MTU to 9000.

13.  Expand IPv4 Settings and enter a unique IP address in the Infra-iSCSI-A subnet but outside of the Cisco UCS iSCSI-IP-Pool-A.

14.  Click Save to save the changes to the VMkernel port.

15.  Select the Port groups tab.

16.  Select the iScsiBootPG line. Select Edit Settings to edit the properties of this port group.

17.  Expand NIC teaming and select Yes to the right of Override failover order.

18.  Select vmnic5 and select Mark unused.

19.  Click Save to complete the changes to the iScsiBootPG.

20.  At the top, select the Virtual switches tab.

21.  Select the iScsiBootvSwitch line and click Edit settings.

22.  Expand NIC teaming and select vmnic5. Select Mark active to make vmnic5 active within the vSwitch.

23.  Click Save to save the changes to the vSwitch.

24.  At the top, select the VMkernel NICs tab.

25.  Click Add VMkernel NIC.

26.  For New port group, enter iScsiBootPG-B

27.  For Virtual switch, select iScsiBootvSwitch.

28.  Leave the VLAN ID set at 0.

29.  Change the MTU to 9000.

30.  Select Static IPv4 settings and expand IPv4 settings.

31.  Enter a unique IP address and netmask in the Infra-iSCSI-B subnet but outside of the Cisco UCS iSCSI-IP-Pool-B.

32.  Do not select any of the Services.

33.  Click Create.

34.  Select the Port groups tab.

35.  Select the iScsiBootPG-B line. Select Edit Settings to edit the properties of this port group.

36.  Expand NIC teaming and select Yes to the right of Override failover order.

37.  To the right of Failover order, select vmnic4 and select Mark unused.

38.  Click Save to save the changes to the port group.

39.  On the left select Storage, then in the center pane select the Adapters tab.

40.  Click Software iSCSI to configure software iSCSI for the host.

41.  In the Configure iSCSI window, under Dynamic targets, select Add dynamic target.

42.  Select to add address and enter the IP address of iscsi-lif-1a from storage SVM Infra-SVM. Press Return.

43.  Repeat this process to add the IP addresses for iscsi-lif-2a, iscsi-lif-1b, and iscsi-lif-2b.

44.  Click Save configuration.

45.  Click Software iSCSI to configure software iSCSI for the host.

46.  Verify that four static targets and four dynamic targets are listed for the host.

47.  Click Cancel to close the window.

48.  Add the host to vCenter, set the swap datastore on the host, and add the host to the VMware vDS, including migrating the vMotion VMkernel port to the vDS.

49.  Using NetApp VSC, set recommended values for the host.

Add iSCSI Configuration to a VMware ESXi Host Added in vCenter

This section details the steps to add iSCSI configuration to an ESXi host added and configured in vCenter. This section assumes the host has been added to vCenter and the basic networking completed, NFS datastores set up, and the time configuration and swap files added.

To add an iSCSI configuration to an ESXi host, follow these steps:

1.     In the vSphere HTML5 Client, under Hosts and Clusters, select the ESXi host.

2.     In the center pane, select Configure. In the list under Networking, select Virtual switches.

3.     In the center pane, expand iScsiBootvSwitch. Click EDIT to edit settings for the vSwitch.

4.     Change the MTU to 9000 and click OK.

5.     Click MANAGE PHYSICAL ADAPTERS to add a network adapter to the vSwitch.

6.     Click the green plus sign to add an adapter.

7.     Select vmnic5.

8.     Click OK. Use the blue down arrow to move vmnic5 under Unused adapters.

9.     Click OK to complete adding the vmnic to the vSwitch.

10.  Select VMkernel adapters.

11.  Select the iScsiBootPG VMkernel adapter. Select EDIT to edit adapter settings.

12.  Change the MTU to 9000.

13.  Click IPv4 settings on the left. Change the IP address to a unique IP address in the Infra-iSCSI-A subnet but outside of the Cisco UCS iSCSI-IP-Pool-A.

14.  Click OK.

15.  Select Virtual switches. In the center pane, expand iScsiBootvSwitch.

16.  Select … to the right of iScsiBootPG in the center of the window. Select Edit Settings.

17.  In the Edit Settings window, select Teaming and failover. In the center of the window under Failover order, select Override.

18.  Click OK to complete editing the port group.

19.  In the list located on the left under Networking, select Virtual switches.

20.  In the center pane, expand iScsiBootvSwitch. Click EDIT to edit settings for the vSwitch.

21.  Select Teaming and failover. Under Failover order, select vmnic5. Use the blue up arrow icon to move vmnic5 to the Active adapters list.

22.  Click OK to complete the changes to the vSwitch.

23.  In the list on the left under Networking, select VMkernel adapters.

24.  In the center pane, select Add Networking to add a VMkernel adapter.

25.  Make sure VMkernel Network Adapter is selected and click NEXT.

26.  Select an existing standard switch and click BROWSE.

27.  Select iScsiBootvSwitch and click OK.

28.  Click NEXT.

29.  Enter iScsiBootPG-B for the Network label, leave VLAN ID set to None (0), select Custom – 9000 for MTU, and click NEXT.

30.  Select Use static IPv4 settings. Enter a unique IP address and netmask in the Infra-iSCSI-B subnet but outside of the Cisco UCS iSCSI-IP-Pool-B.

31.  Click NEXT.

32.  Review the settings and click FINISH to complete creating the VMkernel port.

33.  In the list under Networking, select Virtual switches. Expand iScsiBootvSwitch.

34.  In the center of the window, select … to the right of iScsiBootPG-B. Select Edit Settings.

35.  Select Teaming and failover.  In the center of the window under Failover order, select Override.

36.  Select vmnic4. Use the blue down arrow to move vmnic4 to Unused adapters.

37.  Click OK to complete the changes to the port group.

38.  In the list under Storage, select Storage Adapters.

39.  Select the iSCSI Software Adapter and below, select the Dynamic Discovery tab.

40.  Click Add.

41.  Enter the IP address of the storage controller’s Infra-SVM LIF iscsi-lif-1a and click OK.

42.  Repeat this process to add the IPs for iscsi-lif-2a, iscsi-lif-1b, and iscsi-lif-2b.

43.  Under Storage Adapters, click Rescan Adapter to rescan the iSCSI Software Adapter.

44.  Under Static Discovery. Four static targets should be listed.

45.  Using NetApp VSC, set recommended values for the host.

ESXi Dump Collector Setup for iSCSI-Booted Hosts

ESXi hosts booted with iSCSI using the VMware iSCSI software initiator need to be configured to do core dumps to the ESXi Dump Collector that is part of vCenter. The Dump Collector is not enabled by default on the vCenter Appliance. This procedure should be run at the end of the vCenter deployment section. To setup the ESXi Dump Collector, follow these steps:

1.     Log into the vSphere Web Client as administrator@vsphere.local and select Home.

2.     In the center pane, click System Configuration.

3.     In the left pane, select Services.

4.     Under Services, click VMware vSphere ESXi Dump Collector.

5.     In the center pane, click the green start icon  to start the service.

6.     In the Actions menu, click Edit Startup Type.

7.     Select Automatic.

8.     Click OK.

9.     Connect to each ESXi host via ssh as root

10.  Run the following commands:

Create a FlexPod ESXi Custom ISO using VMware vCenter

In this validation document, the Cisco Custom Image for ESXi 6.7 U2 GA Install CD ISO was used to install VMware ESXi. After this installation the Cisco VIC nfnic and nenic drivers had to be updated and the NetApp NFS Plug-in for VMware VAAI had to be installed during the FlexPod deployment.  vCenter 6.7 U2 can be used to produce a FlexPod custom ISO containing the updated VIC drivers and the NetApp NFS Plug-in for VMware VAAI. This ISO can be used to install VMware ESXi 6.7 U2 without having to do any additional driver updates.  This ISO can be produced by following these steps:

1.     Download the Cisco Custom Image for ESXi 6.7 U2 Offline Bundle. This file (VMware_ESXi_6.7.0_13006603_Custom_Cisco_6.7.2.1_Bundle.zip) can be used to produce the Cisco Custom Image for ESXi 6.7 U2 GA Install CD ISO.

2.     Download the following driver images and extract the listed .zip file:

-      VMware ESXi 6.7 nfnic 4.0.0.38 FC Driver for Cisco nfnic - VMW-ESX-6.7.0-nfnic-4.0.0.38-offline_bundle-14003014.zip

-      VMware ESXi 6.7 nenic 1.0.29.0 NIC Driver for Cisco nenic - VMW-ESX-6.7.0-nenic-1.0.29.0-offline_bundle-12897497.zip

-      NetApp NFS Plug-in for VMware VAAI 1.1.2 – NetAppNasPlugin.v23.zip

3.     Connect to the VMware Appliance Management interface (https://<vcenter-IP>:5480) and login as root.

4.     In the menu on the left, select Services.

5.     In the center pane, select ImageBuilder Service and at the top, click START.

6.     Verify that the ImageBuilder Service now is Healthy and Started. Log out of the VMware Appliance Management interface.

7.     Log into the VMware vCenter HTML5 Client as administrator@vsphere.local.

8.     Under Menu, select Auto Deploy.

9.     In the center pane, select Software Depots.

10.  Click the IMPORT to upload a software depot.

11.  Name the depot ESXi-6.7U2-Custom-Cisco. Click BROWSE. Browse to the local location of the zip file, highlight it, and click Open.

12.  Click UPLOAD to upload the software depot.

13.  Repeat steps 9-12 to add software depots for nfnic-4.0.0.38 and NetAppNasPlugin-v23.

14.  Click NEW to add a custom software depot.

15.  Select Custom depot and name the custom depot FlexPod-ESXi-6.7U2.

16.  Click ADD to add the custom software depot.

17.  From the drop-down list, select the ESXi-6.7U2- Custom-Cisco software depot. Make sure the Image Profiles tab is selected and then use the radio button to select the VMware-ESXi-6.7.0-13006603-Custom-Cisco-6.7.2.1 image profile. Click CLONE to clone the image profile.

18.  Name the clone FlexPod-ESXi-6.7U2. For Vendor, enter Cisco-NetApp. For Description, enter “Cisco Custom ISO for ESXi 6.7U2 GA with nfnic-4.0.0.38, nenic-1.0.29.0, and NetAppNasPlugin-v23”. Select FlexPod-ESXi-6.7U2 for Software depot.

19.  Click NEXT.

20.  Under Available software packages, check NetAppNasPlugin 1.1.2-3, make sure nenic 1.0.29.0 is checked, uncheck nfnic 4.0.0.35, and check nfnic 4.0.0.38.  Leave the remaining selections unchanged.

21.  Click NEXT.

22.  Click FINISH.

23.  Using the Software Depot pulldown, select the FlexPod-ESXi-6.7U2 custom software depot. Under Image Profiles select the FlexPod-ESXi-6.7U2 image profile. Click … > Export to export an image profile. ISO should be selected. Click OK to generate a bootable ESXi installable image.

24.  Once the Image profile export completes, click DOWNLOAD to download the ISO.

25.  Optionally, generate the ZIP archive to generate an offline bundle for the FlexPod image.

FlexPod Backups

Cisco UCS Backup

Automated backup of the UCS domain is important for recovery of the UCS Domain from issues ranging catastrophic failure to human error.  There is a native backup solution within Cisco UCS that allows local or remote backup using FTP/TFTP/SCP/SFTP as options.

Backups created can be a binary file containing the Full State, which can be used for a restore to the original or a replacement pair of fabric interconnects.  Alternately this XML configuration file consisting of All configurations, just System configurations, or just Logical configurations of the UCS Domain.  For scheduled backups, options will be Full State or All Configuration, backup of just the System or Logical configurations can be manually initiated.

To configure the backup, using the Cisco UCS Manager GUI, follow these steps:

1.     Select Admin within the Navigation pane and select All.

2.     Click the Policy Backup & Export tab within All.

3.     For a Full State Backup, All Configuration Backup, or both, specify the following:

a.     Hostname: <IP or FQDN of host that will receive the backup>

b.     Protocol: [FTP/TFTP/SCP/SFTP]

c.     User: <account on host to authenticate>

d.     Password: <password for account on host>

e.     Remote File: <full path and filename prefix for backup file>

f.      Admin State: <select Enable to activate the schedule on save, Disable to disable schedule on Save>

g.     Schedule: [Daily/Weekly/Bi Weekly]

 

4.     Click Save Changes to create the Policy.

Cisco Nexus and MDS Backups

The configuration of the Cisco Nexus 9000 and Cisco MDS 9132T switches can be backed up manually at any time with the copy command, but automated backups can be put in place with the NX-OS feature scheduler.  An example of setting up automated configuration backups of one of the FlexPod 9336C-FX2 switches is shown below:

Show the job that has been setup:

 

The documentation for the feature scheduler can be found here: http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus9000/sw/7-x/system_management/configuration/guide/b_Cisco_Nexus_9000_Series_NX-OS_System_Management_Configuration_Guide_7x/b_Cisco_Nexus_9000_Series_NX-OS_System_Management_Configuration_Guide_7x_chapter_01010.html

VMware VCSA Backup

Basic backup of the vCenter Server Appliance is also available within the native capabilities of the VCSA, though within the default solution this is manually initiated provide a scheduled solution.  To create a backup, follow these steps:

1.     Connect to the VCSA Console at https://<VCSA IP>:5480 as root.

 

2.     Click Time to set the vCenter time zone.

3.     In the center pane, to the right of Timezone, click EDIT.

4.     From the drop-down list select the current time zone and click SAVE.

5.     Click Backup in the list to open up the Backup Appliance Dialogue.

6.     To the right of Backup Schedule, click CONFIGURE.

7.     Specify:

a.     The Backup location with the protocol to use [HTTPS/HTTP/SCP/FTPS/FTP]

b.     The User name and password.

c.     The Number of backups to retain.

8.     Click Create.

9.     The Backup Schedule should now show a Status of Enabled.

10.  Restoration can be initiated with the backed-up files using the Restore function of the VCSA 6.7 Installer.

John George, Technical Marketing Engineer, Data Center Solutions Engineering, Cisco Systems, Inc.

John has been involved in designing, developing, validating, and supporting the FlexPod Converged Infrastructure since it was developed almost nine years ago. Before his roles with FlexPod, he supported and administered a large worldwide training network and VPN infrastructure. John holds a Master's degree in Computer Engineering from Clemson University.

Sree Lakshmi Lanka, Solutions Engineer, Infrastructure and Cloud Engineering, NetApp

Sree is a Solutions Engineer in the Converged Infrastructure Engineering team at NetApp. She has been with NetApp since 2007, serving in a variety of Member Technical Staff- SAN Interoperability Engineering roles. Sree has over 15 years of experience in the IT industry specializing in data management, SAN and security.

Acknowledgements

For their support and contribution to the design, validation, and creation of this Cisco Validated Design, the authors would like to thank:

·       Haseeb Niazi, Technical Marketing Engineer, Cisco Systems, Inc.

·       Ramesh Isaac, Technical Marketing Engineer, Cisco Systems, Inc.

·       Scott Kovacs, Technical Marketing Engineer, NetApp

NOTE: Available paragraph styles are listed in the Quick Styles Gallery in the Styles group on the Home tab. Alternatively, they can be accessed via the Styles window (press Alt + Ctrl + Shift + S).