Explore Cisco
How to Buy

Have an account?

  •   Personalized content
  •   Your products and support

Need an account?

Create an account

Lightweight Access Point Configuration Guide, Cisco IOS XE Release 3SE (Catalyst 3850 Switches)

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Book Contents
Find Matches in This Book
Available Languages
Download Options

Book Title

Lightweight Access Point Configuration Guide, Cisco IOS XE Release 3SE (Catalyst 3850 Switches)

Chapter Title

Optimizing RFID Tracking

Results

Updated:
January 17, 2018

Chapter: Optimizing RFID Tracking

Optimizing RFID Tracking

Finding Feature Information

Optimizing RFID Tracking on Access Points

To optimize the monitoring and location calculation of RFID tags, you can enable tracking optimization on up to four channels within the 2.4-GHz band of an 802.11b/g access point radio. This feature allows you to scan only the channels on which tags are usually programmed to operate (such as channels 1, 6, and 11).

How to Optimize RFID Tracking on Access Points

Optimizing RFID Tracking on Access Points (CLI)

SUMMARY STEPS

    1.    ap name Cisco_AP mode monitor submode none

    2.    ap name Cisco_AP dot11 24ghz shutdown

    3.    ap name Cisco_AP monitor-mode tracking-opt

    4.    ap name Cisco_AP monitor-mode dot11b {fast-channel [first_channel second_channel third_channel fourth_channel]}

    5.    ap name Cisco_AP no dot11 24ghz shutdown

    6.    show ap monitor-mode summary


DETAILED STEPS
     Command or ActionPurpose
    Step 1ap name Cisco_AP mode monitor submode none


    Example:
    Switch# ap name 3602a mode monitor
 submode none
     

    Specifies the monitor submode for the access point as none.

    Note   

    A warning message indicates that changing the access point's mode will cause the access point to reboot and prompts you to specify whether you want to continue by entering Y.

    After you enter Y, the access point reboots.

     
    Step 2ap name Cisco_AP dot11 24ghz shutdown


    Example: 
    Switch# ap name AP01 dot11 24ghz shutdown
     

    Disables the access point radio.

     
    Step 3ap name Cisco_AP monitor-mode tracking-opt


    Example:
    Switch# ap name TSIM_AP1 monitor-mode
 tracking-opt
     

    Configures the access point to scan only the Dynamic Channel Assignment (DCA) channels supported by its country of operation.

    Note   

    To disable tracking optimization for an access point, enter the ap name Cisco_AP monitor-mode tracking-opt no-optimization command.

     
    Step 4ap name Cisco_AP monitor-mode dot11b {fast-channel [first_channel second_channel third_channel fourth_channel]}


    Example:
    Switch# ap name AP01 monitor-mode dot11b
 fast-channel 1 2 3 4
     
    Chooses up to four specific 802.11b channels to be scanned by the access point.
    Note   

    In the United States, you can assign any value from 1 to 11 (inclusive) to the channel variable. Other countries support additional channels. You must assign at least one channel.

     
    Step 5ap name Cisco_AP no dot11 24ghz shutdown


    Example:
    Switch# ap name AP01 no dot11 24ghz shutdown
     

    Enables the access point radio.

     
    Step 6show ap monitor-mode summary


    Example:
    Switch# show ap monitor-mode summary
     

    Displays all the access points in monitor mode.

     

    Configuration Examples for Optimizing RFID Tracking

    Displaying all the Access Points in Monitor Mode: Example

    This example shows how to display all the access points in monitor mode:

    Switch# show ap monitor-mode summary

AP Name       Ethernet MAC   Status   Scanning
                                      Channel
                                      List
------------- -------------- -------- ---------
AP1131:4f2.9a 00:16:4:f2:9:a Tracking 1,6,NA,NA

    Was this Document Helpful?

    FeedbackFeedback

    Contact Cisco