Command Reference, Cisco IOS XE Denali 16.3.x (Catalyst 3850 Switches)

ap hyperlocation

To configure hyperlocation and related parameters, use the ap hyperlocation command. To disable hyperlocation and related parameters, use the no form of this command.

ap hyperlocation [ ble-beacon{ beacon-id | interval interval-value} | threshold { detection value-in-dBm | reset value-btwn-0-99 | trigger value-btwn-1-100} ]

[no] ap hyperlocation [ ble-beacon{ beacon-id | interval interval-value} | threshold { detection value-in-dBm | reset value-btwn-0-99 | trigger value-btwn-1-100} ]

Syntax Description

ble-beacon

Enables BLE beacon parameters.

beacon-id

BLE beacon ID. The range is from 1 to 4.

interval

Sets the BLE beacon interval.

interval-value

BLE beacon interval value, in hertz. The range is from 1 to 10. The default is1.

threshold detection value-in-dBm

Sets threshold to filter out packets with low RSSI. The [no] form of the command resets the threshold to its default value.

threshold reset value-btwn-0-99

Resets value in scan cycles after trigger. The [no] form of the command resets the threshold to its default value.

threshold trigger value-btwn-1-100

Sets the number of scan cycles before sending a BAR to clients. The [no] form of the command resets the threshold to its default value.

Note

Ensure that the hyperlocation threshold reset value is less than the threshold trigger value.

Command History

Release	Modification
Cisco IOS XE Denali 16.2.1	This command was introduced.
Cisco IOS XE Denali 16.3.1	This command was modified. The ble-beacon keyword was added.

Related References

show ap hyperlocation

ap name hyperlocation

To configure hyperlocation and related parameters for an access point (AP), use the ap name hyperlocation command. To disable hyperlocation and related parameters, use the no form of this command.

ap name ap-namehyperlocation ble-beacon beacon-id{ major major-value | minor minor-value | txpwr att-value }

Syntax Description

ap-name	Access point name.
ble-beacon	Configures BLE beacon parameters.
beacon-id	BLE beacon ID.
major	Configures BLE beacon major parameter.
major-value	BLE beacon major value. The range is from 0 to 65535. The default is 0.
minor	Configures BLE beacon minor parameter.
minor-value	BLE beacon minor value. The range is from 0 to 65535. The default is 0.
txpwr	Configures BLE beacon attenuation level.
att-value	BLE beacon attenuation value, in dBm. The range is from 0 to 52. The default is 0.

Command Default

BLE beacon details are not configured.

Command Modes

Privileged EXEC (#)

Command History

Release	Modification
Cisco IOS XE Denali 16.3.1	This command was introduced.

Example

This example shows how to configure hyperlocation and related parameters for an AP:

Controller# ap name test-ap hyperlocation ble-beacon 3 txpwr 50

hyperlocation

To configure Hyperlocation and related parameters for an AP group, use the hyperlocation command in the WLAN AP Group configuration (Device(config-apgroup)#) mode. To disable Hyperlocation and related parameter configuration for the AP group, use the no form of the command.

[no] hyperlocation [ threshold { detection value-in-dBm | reset value-btwn-0-99 | trigger value-btwn-1-100} ]

Syntax Description

[no] hyperlocation

Enables or disables Hyperlocation for an AP group.

threshold detection value-in-dBm

Sets threshold to filter out packets with low RSSI. The [no] form of the command resets the threshold to its default value.

threshold reset value-btwn-0-99

Resets value in scan cycles after trigger. The [no] form of the command resets the threshold to its default value.

threshold trigger value-btwn-1-100

Sets the number of scan cycles before sending a BAR to clients. The [no] form of the command resets the threshold to its default value.

Note

Ensure that the Hyperlocation threshold reset value is less than the threshold trigger value.

Command Modes

WLAN AP Group configuration

Command History

Release	Modification
Cisco IOS XE Denali 16.3.1	This command was introduced.

This example shows how to set threshold to filter out packets with low RSSI:
```
Device(config-apgroup)# [no] hyperlocation threshold detection -100
```
This example shows how to reset value in scan cycles after trigger:
```
Device(config-apgroup)# [no] hyperlocation threshold reset 8
```
This example shows how to set the number of scan cycles before sending a BAR to clients:
```
Device(config-apgroup)# [no] hyperlocation threshold trigger 10
```

ap ntp ip

To configure the IPv4 address of the NTP server, directly reachable by the access points, use the ap ntp ip command. To remove the IPv4 address that is configured for the NTP server, use the no form of the command.

NTP is mandatory for Hyperlocation to work. If NTP is not defined, Hyperlocation will not be operational.
NTP server must be reachable from the AP VLAN.

If the IPv4 address of the NTP server is not configured, the IP address of the globally configured NTP server is used.

Note

The show commands display the details of the NTP server that is effectively used. For example, if the globally configured IPv4 address of the NTP server is 0.0.0.0, the show ap hyperlocation {summary | detail} command shows the details of the globally configured NTP server.

[no] ap ntp ip ipv4-addr

Syntax Description

ipv4-addr

IPv4 address of the NTP server. The [no] form of the command resets the NTP value to 0.0.0.0.

Command History

Release	Modification
Cisco IOS XE Denali 16.2.1	This command was introduced.

ntp ip

To set the IPv4 address of the NTP server, directly reachable by the APs of an AP group, use the ntp ip command in the WLAN AP Group configuration (Device(config-apgroup)#) mode. To remove the IPv4 address that is configured for the NTP server, use the no form of the command.

NTP is mandatory for Hyperlocation to work. If NTP is not defined, Hyperlocation will not be operational.
NTP server must be reachable from the AP VLAN.

If the IPv4 address of the NTP server is not configured, the IP address of the globally configured NTP server is used.

Note

The show commands display the details of the NTP server that is effectively used. For example, if the AP NTP server (configured via the ntp ip ip-addr command) is set to 0.0.0.0, the show ap group hyperlocation {summary | detail} command shows the details of one of the NTP servers from the system-wide IOS NTP configuration.

[no] ntp ip ipv4-addr

Syntax Description

ipv4-addr

IPv4 address of the NTP server. The [no] form of the command resets the NTP value to 0.0.0.0.

Command Modes

WLAN AP Group configuration

Command History

Release	Modification
Cisco IOS XE Denali 16.3.1	This command was introduced.

arp

To display the contents of the Address Resolution Protocol (ARP) table, use the arp command in boot loader mode.

arp [ip_address]

Syntax Description

ip_address

(Optional) Shows the ARP table or the mapping for a specific IP address.

Command Default

No default behavior or values.

Command Modes

Boot loader

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

The ARP table contains the IP-address-to-MAC-address mappings.

Example

This example shows how to display the ARP table:

Device: arp 172.20.136.8
arp'ing 172.20.136.8...
172.20.136.8 is at 00:1b:78:d1:25:ae, via port 0

Related References

set

boot

To load and boot an executable image and display the command-line interface (CLI), use the boot command in boot loader mode.

boot [ -post | -n | -p | flag] filesystem:/file-url...

Syntax Description

-post	(Optional) Run the loaded image with an extended or comprehensive power-on self-test (POST). Using this keyword causes POST to take longer to complete.
-n	(Optional) Pause for the Cisco IOS Debugger immediately after launching.
-p	(Optional) Pause for the JTAG Debugger right after loading the image.
filesystem:	Alias for a file system. Use flash: for the system board flash device; use usbflash0: for USB memory sticks.
/file-url	Path (directory) and name of a bootable image. Separate image names with a semicolon.

Command Default

No default behavior or values.

Command Modes

Boot loader

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

When you enter the boot command without any arguments, the device attempts to automatically boot the system by using the information in the BOOT environment variable, if any.

If you supply an image name for the file-url variable, the boot command attempts to boot the specified image.

When you specify boot loader boot command options, they are executed immediately and apply only to the current boot loader session.

These settings are not saved for the next boot operation.

Filenames and directory names are case sensitive.

Example

This example shows how to boot the device using the new-image.bin image:

Device: set BOOT flash:/new-images/new-image.bin
Device: boot

After entering this command, you are prompted to start the setup program.

cat

To display the contents of one or more files, use the cat command in boot loader mode.

cat filesystem:/file-url...

Syntax Description

filesystem:	Specifies a file system.
/file-url	Specifies the path (directory) and name of the files to display. Separate each filename with a space.

Command Default

No default behavior or values.

Command Modes

Boot loader

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

Filenames and directory names are case sensitive.

If you specify a list of files, the contents of each file appears sequentially.

Example

This example shows how to display the contents of an image file:

Device: cat flash:image_file_name
version_suffix: universal-122-xx.SEx
version_directory: image_file_name
image_system_type_id: 0x00000002
image_name: image_file_name.bin
ios_image_file_size: 8919552
total_image_file_size: 11592192
image_feature: IP|LAYER_3|PLUS|MIN_DRAM_MEG=128
image_family: family
stacking_number: 1.34
board_ids: 0x00000068 0x00000069 0x0000006a 0x0000006b 
info_end:

clear location

To clear a specific radio frequency identification (RFID) tag or all of the RFID tags information in the entire database, use the clear location command in EXEC mode.

clear location [mac-address mac-address | rfid]

Syntax Description

mac-address mac-address	MAC address of a specific RFID tag.
rfid	Specifies all of the RFID tags in the database.

Command Default

No default behavior or values.

Command Modes

User EXEC

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

This example shows how to clear information about all of the RFID tags in the database:

Device> clear location rfid

clear location statistics

To clear radio-frequency identification (RFID) statistics, use the clear location statistics command in EXEC mode.

clear location statistics

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

User EXEC

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

The following is sample output from the clear location rfid command and shows how to clear RFID statistics:

Device> clear location statistics

clear nmsp statistics

To clear the Network Mobility Services Protocol (NMSP) statistics, use the clear nmsp statistics command in EXEC mode.

clear nmsp statistics

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

User Exec

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

The following is sample output from the clear nmsp statistics command and shows how to clear all statistics about NMSP information exchanged between the controller and the connected Cisco Mobility Services Engine (MSE):

Device> clear nmsp statistics

clear wireless ccx statistics

To clear CCX statistics, use the clear wireless ccx statistics command in EXEC mode.

clear wireless ccx statistics

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

User EXEC

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

The following is sample output from the clear wireless ccx statistics command and shows how to clear all collected statistics about CCX clients:

Device> clear wireless ccx statistics

clear wireless client tsm dot11

To clear the traffic stream metrics (TSM) statistics for a particular access point or all of the access points to which this client is associated, use the clear wireless client tsm dot11 command in EXEC mode.

clear wireless client tsm dot11 { 24ghz | 5ghz } client-mac-addr { all | name ap-name }

Syntax Description

24ghz	Specifies the 802.11a network.
5ghz	Specifies the 802.11b network.
client-mac-addr	MAC address of the client.
all	Specifies all access points.
name ap-name	Name of a Cisco lightweight access point.

Command Default

No default behavior or values.

Command Modes

User EXEC

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

The following is sample output from the clear wireless client tsm dot11 command and shows how to clear the TSM for the MAC address 00:40:96:a8:f7:98 on all of the access points 5-GHz radios where this client is known:

Device> clear wireless client tsm dot11 5ghz 00:40:96:a8:f7:98 all

clear wireless location s69 statistics

To clear statistics about S69 exchanges with CCXv5 clients, use the clear wireless location s69 statistics command in EXEC mode.

clear wireless location s69 statistics

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

User EXEC

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

S69 messages are exchanged between CCXv5 clients and the wireless infrastructure. The CCXv5 client uses S69 message to request location information, that is then returned by the wireless infrastructure through a S69 response message.

Example

The following is sample output from the clear wireless location s69 statistics command and shows how to clear statistics about S69 exchanges with CCXv5 clients:

Device> clear wireless location s69 statistics

copy

To copy a file from a source to a destination, use the copy command in boot loader mode.

copy filesystem:/source-file-urlfilesystem:/destination-file-url

Syntax Description

filesystem:	Alias for a file system. Use usbflash0: for USB memory sticks.
/source-file-url	Path (directory) and filename (source) to be copied.
/destination-file-url	Path (directory) and filename of the destination.

Command Default

No default behavior or values.

Command Modes

Boot loader

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

Filenames and directory names are case sensitive.

Directory names are limited to 127 characters between the slashes (/); the name cannot contain control characters, spaces, deletes, slashes, quotes, semicolons, or colons.

Filenames are limited to 127 characters; the name cannot contain control characters, spaces, deletes, slashes, quotes, semicolons, or colons.

If you are copying a file to a new directory, the directory must already exist.

Example

This example shows how to copy a file at the root:

Device: copy usbflash0:test1.text usbflash0:test4.text
File "usbflash0:test1.text" successfully copied to "usbflash0:test4.text"

You can verify that the file was copied by entering the dir filesystem: boot loader command.

config-ble

To configure a BLE beacon value, use the config-ble command.

config-ble { default { enable | txpwr | uuid } | enable | exit | no { enable | txpwr | uuid uuid-name } | txpwratt-value| uuid}

Syntax Description

default	Sets a command to its default value.
enable	Enables a BLE beacon.
txpwr	Configures the BLE beacon attenuation level.
uuid	Configures universally unique identifier (UUID).
uuid-string	UUID hexadecimal string. As defined by RFC standards (RFC4122), the GUI accepts user input in both upper and lowercase characters, but the input is stored in lowercase.
exit	Exits the config-ble submode.
no	Negate a command or sets it to default values.
att-value	BLE beacon attenuation value, in dBm. The range is from 0 to 52. The default is 0.

Command Default

BLE beacon values are not configured.

Command Modes

config-ble

Command History

Release	Modification
Cisco IOS XE Denali 16.3.1	This command was introduced.

Usage Guidelines

Use this command to configure BLE beacon parameters.

Example

The following example shows how to enable BLE beacon:

Controller(config-ble)# enable

copy startup-config tftp:

To copy the configuration settings from a switch to a TFTP server, use the copy startup-config tftp: command in Privileged EXEC mode.

copy startup-config tftp: remote host {ip-address}/{name}

Syntax Description

remote host {ip-address}/{name}

Host name or IP-address of Remote host.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE Release 16.1	This command was introduced.

Usage Guidelines

To copy your current configurations from the switch, run the command copy startup-config tftp: and follow the instructions. The configurations are copied onto the TFTP server.

Then, login to another switch and run the command copy tftp: startup-config and follow the instructions. The configurations are now copied onto the other switch.

Example

This example shows how to copy the configuration settings onto a TFTP server:

Device: copy startup-config tftp:
Address or name of remote host []?

copy tftp: startup-config

To copy the configuration settings from a TFTP server onto a new switch, use the copy tftp: startup-config command in Privileged EXEC mode on the new switch.

copy tftp: startup-config remote host {ip-address}/{name}

Syntax Description

remote host {ip-address}/{name}

Host name or IP-address of Remote host.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE Release 16.1	This command was introduced.

Usage Guidelines

After the configurations are copied, to save your configurations, use write memory command and then either reload the switch or run the copy startup-config running-config command.

Example

This example shows how to copy the configuration settings from the TFTP server onto a switch:

Device: copy tftp: startup-config
Address or name of remote host []?

debug call-admission wireless all

To enable debugging of the wireless Call Admission Control (CAC) feature, use the debug call-admission wireless all command in privileged EXEC mode. To disable debugging, use the no form of this command.

debug call-admission wireless all [ switch switch ]

no debug call-admission wireless all [ switch switch ]

Syntax Description

switch

Configures debugging options for all wireless CAC messages associated to a particular switch.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

The following is sample output from the debug call-admission wireless switch command and shows how to enable debugging options for CAC messages:

Device# debug call-admission wireless switch 1 all

debug rfid

To configure radio-frequency identification (RFID) debug options, use the debug rfid command in privileged EXEC mode. To disable debugging, use the no form of this command.

debug rfid { debug_leaf_name| all | detail | error| nmsp| receive} [ filter| switch switch ]

no debug rfid { debug_leaf_name| all | detail | error | nmsp | receive} [ filter | switch switch ]

Syntax Description

debug_leaf_name	Debug leaf name.
all	Configures debugging of all RFID.
detail	Configures debugging of RFID detail.
error	Configures debugging of RFID error messages.
nmsp	Configures debugging of RFID Network Mobility Services Protocol (NMSP) messages.
receive	Configures debugging of incoming RFID tag messages.
filter	Debug flag filter name.
switch switch	Configures RFID debugging for device.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

The following is sample output from the debug rfid command and shows how to enable debugging of RFID error messages:

Device# debug rfid error switch 1

debug voice diagnostics mac-address

To enable debugging of voice diagnostics for voice clients, use the debug voice diagnostics mac-address command in privileged EXEC mode. To disable debugging, use the no form of this command.

debug voice diagnostics mac-address mac-address1 verbose mac-address mac-address2 verbose

nodebug voice diagnostics mac-address mac-address1 verbose mac-address mac-address2 verbose

Syntax Description

voice diagnostics	Configures voice debugging for voice clients.
mac-address mac-address1 mac-address mac-address2	Specifies MAC addresses of the voice clients.
verbose	Enables verbose mode for voice diagnostics.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

The following is sample output from the debug voice diagnostics mac-address command and shows how to enable debugging of voice diagnostics for voice client with MAC address of 00:1f:ca:cf:b6:60:

Device# debug voice diagnostics mac-address 00:1f:ca:cf:b6:60

debug wps mfp

To enable WPS MFP debugging options, use the debug wps mfp command in privileged EXEC mode. To disable debugging, use the no form of this command.

debug wps mfp { all | capwap| client | detail| mm| report}[ switch switch]

Syntax Description

wps mfp	Configures WPS MFP debugging options.
all	Displays all WPS MFP debugging messages.
capwap	Displays MFP messages.
client	Displays client MFP messages.
detail	Displays detailed MFP CAPWAP messages.
mm	Displays MFP mobility (inter-controller) messages.
report	Displays MFP reports.
switch switch	Displays the WPS MFP debugging for the device.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

This example shows how to enable WPS MFP debugging options for client:

Device# debug wps mfp client switch 1

delete

To delete one or more files from the specified file system, use the delete command in boot loader mode.

delete filesystem:/file-url...

Syntax Description

filesystem:	Alias for a file system. Use usbflash0: for USB memory sticks.
/file-url...	Path (directory) and filename to delete. Separate each filename with a space.

Command Default

No default behavior or values.

Command Modes

Boot loader

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

Filenames and directory names are case sensitive.

The device prompts you for confirmation before deleting each file.

Example

This example shows how to delete two files:

Device: delete usbflash0:test2.text usbflash0:test5.text
Are you sure you want to delete "usbflash0:test2.text" (y/n)?y
File "usbflash0:test2.text" deleted
Are you sure you want to delete "usbflash0:test5.text" (y/n)?y
File "usbflash0:test2.text" deleted

You can verify that the files were deleted by entering the dir usbflash0: boot loader command.

dir

To display the list of files and directories on the specified file system, use the dir command in boot loader mode.

dir filesystem:/file-url

Syntax Description

filesystem:	Alias for a file system. Use flash: for the system board flash device; use usbflash0: for USB memory sticks.
/file-url	(Optional) Path (directory) and directory name that contain the contents you want to display. Separate each directory name with a space.

Command Default

No default behavior or values.

Command Modes

Boot Loader

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

Directory names are case sensitive.

Example

This example shows how to display the files in flash memory:

Device: dir flash:
Directory of flash:/
    2  -rwx        561   Mar 01 2013 00:48:15  express_setup.debug
    3  -rwx    2160256   Mar 01 2013 04:18:48  c2960x-dmon-mz-150-2r.EX
    4  -rwx       1048   Mar 01 2013 00:01:39  multiple-fs
    6  drwx        512   Mar 01 2013 23:11:42  c2960x-universalk9-mz.150-2.EX
   645 drwx        512   Mar 01 2013 00:01:11  dc_profile_dir
   647 -rwx       4316   Mar 01 2013 01:14:05  config.text
   648 -rwx          5   Mar 01 2013 00:01:39  private-config.text

   96453632 bytes available (25732096 bytes used)

Table 1 dir Field Descriptions
Field	Description
2	Index number of the file.
-rwx	File permission, which can be any or all of the following: d—directory r—readable w—writable x—executable
1644045	Size of the file.
<date>	Last modification date.
env_vars	Filename.

Related References

mkdir

rmdir

emergency-install

To perform an emergency installation on your system, use the emergency-install command in boot loader mode.

emergency-install url://<url>

Syntax Description

<url>

URL and name of the file containing the emergency installation bundle image.

Command Default

No default behavior or values.

Command Modes

Boot loader

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

The boot flash is erased during the installation operation.

Example

This example shows how to perform the emergency install operation using the contents of an image file:

Device: emergency-install tftp:<url> 
The bootflash will be erased during install operation, continue (y/n)?y
Starting emergency recovery (tftp:<url> ...
Reading full image into memory......................done
Nova Bundle Image
--------------------------------------
Kernel Address    : 0x6042d5c8
Kernel Size       : 0x317ccc/3243212
Initramfs Address : 0x60745294
Initramfs Size    : 0xdc6774/14444404
Compression Format: .mzip

Bootable image at @ ram:0x6042d5c8
Bootable image segment 0 address range [0x81100000, 0x81b80000] is in range          \
[0x80180000, 0x90000000].
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
File "sda9:c3850-recovery.bin" uncompressed and installed, entry point: 0x811060f0
Loading Linux kernel with entry point 0x811060f0 ...
Bootloader: Done loading app on core_mask: 0xf

### Launching Linux Kernel (flags = 0x5)



Initiating Emergency Installation of bundle                                          \
tftp:<url> 


Downloading bundle tftp:<url>... 

Validating bundle tftp:<url>... 
Installing bundle tftp:<url>... 
Verifying bundle tftp:<url>... 
Package cat3k_caa-base.SPA.03.02.00SE.pkg is Digitally Signed
Package cat3k_caa-drivers.SPA.03.02.00.SE.pkg is Digitally Signed
Package cat3k_caa-infra.SPA.03.02.00SE.pkg is Digitally Signed
Package cat3k_caa-iosd-universalk9.SPA.150-1.EX.pkg is Digitally Signed
Package cat3k_caa-platform.SPA.03.02.00.SE.pkg is Digitally Signed
Package cat3k_caa-wcm.SPA.10.0.100.0.pkg is Digitally Signed
Preparing flash... 
Syncing device... 
Emergency Install successful... Rebooting
Restarting system.\ufffd


Booting...(use DDR clock 667 MHz)Initializing and Testing RAM                        \
+++@@@@####...++@@++@@++@@++@@++@@++@@++@@++@@done.
Memory Test Pass!

Base ethernet MAC Address: 20:37:06:ce:25:80
Initializing Flash...

flashfs[7]: 0 files, 1 directories
flashfs[7]: 0 orphaned files, 0 orphaned directories
flashfs[7]: Total bytes: 6784000
flashfs[7]: Bytes used: 1024
flashfs[7]: Bytes available: 6782976
flashfs[7]: flashfs fsck took 1 seconds....done Initializing Flash.

The system is not configured to boot automatically. The
following command will finish loading the operating system
software:

    boot

exit

To return to the previous mode or exit from the CLI EXEC mode, use the exit command.

exit

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Global configuration

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

This example shows how to exit the configuration mode:

Device(config)# exit
Device#

flash_init

To initialize the flash: file system, use the flash_init command in boot loader mode.

flash_init

Syntax Description

This command has no arguments or keywords.

Command Default

The flash: file system is automatically initialized during normal system operation.

Command Modes

Boot loader

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

During the normal boot process, the flash: file system is automatically initialized.

Use this command to manually initialize the flash: file system. For example, you use this command during the recovery procedure for a lost or forgotten password.

help

To display the available commands, use the help command in boot loader mode.

help

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

Boot loader

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Example

This example shows how to display a list of available boot loader commands:

Device:help
? -- Present list of available commands
arp -- Show arp table or arp-resolve an address
boot -- Load and boot an executable image
cat -- Concatenate (type) file(s)
copy -- Copy a file
delete -- Delete file(s)
dir -- List files in directories
emergency-install -- Initiate Disaster Recovery
...
...
...
unset -- Unset one or more environment variables
version -- Display boot loader version

license right-to-use

To configure right-to-use access point adder licenses on the device, use the license right-to-use command in privileged EXEC mode.

license right-to-use { activate | deactivate } apcount | ipbase | ipservices | lanbase

Syntax Description

activate	Activates permanent or evaluation ap-count licenses.
deactivate	Deactivates permanent or evaluation ap-count licenses.
apcount count	Specifies the number of ap-count licenses added. You can configure the number of adder licenses from 5 to 50.
ipbase count	Activates ipbase licenses on the switch.
ipservices count	Activates ipservices licenses on the switch.
lanbase count	Activates lanbase licenses on the switch.

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

This example shows how to activate an ap-count evaluation license:

Device# license right-to-use activate apcount evaluation  
Device# end

This example shows how to activate an ap-count permanent license:


Device# license right-to-use deactivate apcount evaluation 
Device# end

This example shows how to add a new ap-count license:


Device# license right-to-use activate apcount 500 slot 1  
Device# end

location

To configure location information for an endpoint, use the location command in global configuration mode. To remove the location information, use the no form of this command.

location { admin-tag string | algorithm | civic-location identifier { host | id } | civic-location identifier { host | id } | elin-location { string | identifier id} | expiry { calibrating-clienttimeout-value| clienttimeout-value| rouge-apstimeout-value| tagstimeout-value } | geo-location identifier { host | id } | notify-threshold { clientdb| rouge-apsdb| tagsdb | plm { calibrating | { multiband | uniband } | clientburst-interval } | prefer { cdp weightpriority-value | lldp-med weightpriority-value | static config weightpriority-value } | rfid { status | timeoutrfid-timeout-value| vendor-namename } | rssi-half-life { calibrating-clientseconds| clientseconds| rogue-apsseconds| tagsseconds }

no location { admin-tag string | algorithm | civic-location identifier { host | id } | civic-location identifier { host | id } | elin-location { string | identifier id} | expiry { calibrating-clienttimeout-value| clienttimeout-value| rouge-apstimeout-value| tagstimeout-value } | geo-location identifier { host | id } | notify-threshold { clientdb| rouge-apsdb| tagsdb | plm { calibrating | { multiband | uniband } | clientburst-interval } | prefer { cdp weightpriority-value | lldp-med weightpriority-value | static config weightpriority-value } | rfid { status | timeoutrfid-timeout-value| vendor-namename } | rssi-half-life { calibrating-clientseconds| clientseconds| rogue-apsseconds| tagsseconds }

Syntax Description

admin-tagstring

Configures administrative tag or site information. Site or location information in alphanumeric format.

algorithm

Configures the algorithm used to average RSSI and SNR values.

civic-location

Configures civic location information.

identifier

Specifies the name of the civic location, emergency, or geographical location.

host

Defines the host civic or geo-spatial location.

id

Name of the civic, emergency, or geographical location.

Note

The identifier for the civic location in the LLDP-MED switch TLV is limited to 250 bytes or less. To avoid error messages about available buffer space during switch configuration, be sure that the total length of all civic-location information specified for each civic-location identifier does not exceed 250 bytes.

elin-location

Configures emergency location information (ELIN).

expiry {calibrating-client | client | rogue-aps | tags} timeout-value

Configures the timeout for RSSI values for calibrating clients, clients, rouge access points, and RFID tags.

The valid range for the timeout parameter for calibrating clients is 1 to 3600 seconds, and the default value is 5 seconds.

The valid range for the timeout parameter for clients, rogue access points, and RFID tags is 5 to 3600 seconds, and the default value is 5 seconds

geo-location

Configures geo-spatial location information.

notify-threshold {client| rogue-aps| tags} db

Configures the NMSP notification threshold for RSSI measurements.

The valid range for the threshold parameter is 0 to 10 dB, and the default value is 0 dB.

calibrating {multiband | uniband} | client seconds

Configures path loss measurement (CCX S60) request for calibrating clients and burst interval for clients.

The valid range for the burst interval parameter is 0 to 3600 seconds.

prefer

Sets location information source priority.

rfid

Configures RFID tag tracking for a location.

rssi-half-life

Configures the RSSI half life for various devices.

Command Default

No default behavior or values.

Command Modes

Global configuration

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

After entering the location civic-location identifier global configuration command, you enter civic location configuration mode. After entering the location geo-location identifier global configuration command, you enter geo location configuration mode.

The civic-location identifier must not exceed 250 bytes.

The host identifier configures the host civic or geo-spatial location. If the identifier is not a host, the identifier only defines a civic location or geo-spatial template that can be referenced on the interface.

The host keyword defines the device location. The civic location options available for configuration using the identifier and the host keyword are the same. You can specify the following civic location options in civic location configuration mode:

additional-code—Sets an additional civic location code.
additional-location-information—Sets additional civic location information.
branch-road-name—Sets the branch road name.
building—Sets building information.
city—Sets the city name.
country—Sets the two-letter ISO 3166 country code.
county—Sets the county name.
default—Sets a command to its defaults.
division—Sets the city division name.
exit—Exits from the civic location configuration mode.
floor—Sets the floor number.
landmark—Sets landmark information.
leading-street-dir—Sets the leading street direction.
name—Sets the resident name.
neighborhood—Sets neighborhood information.
no—Negates the specified civic location data and sets the default value.
number—Sets the street number.
post-office-box—Sets the post office box.
postal-code—Sets the postal code.
postal-community-name—Sets the postal community name.
primary-road-name—Sets the primary road name.
road-section—Sets the road section.
room—Sets room information.
seat—Sets seat information.
state—Sets the state name.
street-group—Sets the street group.
street-name-postmodifier—Sets the street name postmodifier.
street-name-premodifier—Sets the street name premodifier.
street-number-suffix—Sets the street number suffix.
street-suffix—Sets the street suffix.
sub-branch-road-name—Sets the sub-branch road name.
trailing-street-suffix—Sets the trailing street suffix.
type-of-place—Sets the type of place.
unit—Sets the unit.

You can specify the following geo-spatial location information in geo-location configuration mode:

altitude—Sets altitude information in units of floor, meters, or feet.
latitude—Sets latitude information in degrees, minutes, and seconds. The range is from -90 degrees to 90 degrees. Positive numbers indicate locations north of the equator.
longitude—Sets longitude information in degrees, minutes, and seconds. The range is from -180 degrees to 180 degrees. Positive numbers indicate locations east of the prime meridian.
resolution—Sets the resolution for latitude and longitude. If the resolution value is not specified, default value of 10 meters is applied to latitude and longitude resolution parameters. For latitude and longitude, the resolution unit is measured in meters. The resolution value can also be a fraction.
default—Sets the geographical location to its default attribute.
exit—Exits from geographical location configuration mode.
no—Negates the specified geographical parameters and sets the default value.

Use the no lldp med-tlv-select location information interface configuration command to disable the location TLV. The location TLV is enabled by default.

This example shows how to configure civic location information on the switch:

Device(config)# location civic-location identifier 1
Device(config-civic)# number 3550
Device(config-civic)# primary-road-name “Cisco Way”
Device(config-civic)# city “San Jose”
Device(config-civic)# state CA
Device(config-civic)# building 19
Device(config-civic)# room C6
Device(config-civic)# county “Santa Clara”
Device(config-civic)# country US
Device(config-civic)# end

You can verify your settings by entering the show location civic-location privileged EXEC command.

This example shows how to configure the emergency location information on the switch:

Device(config)# location elin-location 14085553881 identifier 1

You can verify your settings by entering the show location elin privileged EXEC command.

The example shows how to configure geo-spatial location information on the switch:

Device(config)# location geo-location identifier host
Device(config-geo)# latitude 12.34
Device(config-geo)# longitude 37.23
Device(config-geo)# altitude 5 floor
Device(config-geo)# resolution 12.34

You can use the show location geo-location identifier command to display the configured geo-spatial location details.

location algorithm

To configure the algorithm used to average RSSI and SNR values, use the location algorithm command in global configuration mode. To remove the algorithm used to average RSSI and SNR values, use the no form of this command.

location algorithm { rssi-average | simple }

no location algorithm { rssi-average | simple }

Syntax Description

rssi-average	Specifies a more accurate algorithm but with more CPU overhead.
simple	Specifies faster algorithm with smaller CPU overhead but less accuracy.

Command Default

RSSI average

Command Modes

Global configuration

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

This example shows how to configure a more accurate algorithm but with more CPU overhead:

Device# configure terminal
Device(config)# location algorithm rssi-average
Device(config)# end

location expiry

To configure the timeout for RSSI values, use the location expiry command in global configuration mode.

location expiry { calibrating-client | client | rogue-aps | tags } timeout-value

Syntax Description

calibrating-client	Specifies the RSSI timeout value for calibrating clients.
client	(Optional) Specifies the RSSI timeout value for clients.
rogue-aps	Specifies the RSSI timeout value for rogue access points.
tags	Specifies the RSSI timeout value for RFID tags.
timeout-value	The valid range for the timeout parameter for calibrating clients is 1 to 3600 seconds, and the default value is 5 seconds. The valid range for the timeout parameter for clients, rogue access points, and RFID tags is 5 to 3600 seconds, and the default value is 5 seconds.

Command Default

No default behavior or values.

Command Modes

Global configuration

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

This example shows how to set the RSSI timeout value for wireless clients:

Device# configure terminal
Device(config)# location expiry client 1000
Device(config)# end

location notify-threshold

To configure the NMSP notification threshold for RSSI measurements, use the location notify-threshold command in global configuration mode. To remove the NMSP notification threshold for RSSI measurements, use the no form of this command.

location notify-threshold { client | rogue-aps | tags } db

no location notify-threshold { client | rogue-aps | tags }

Syntax Description

client	Specifies the NMSP notification threshold (in dB) for clients and rogue clients. The valid range for the threshold parameter is 0 to 10 dB, and the default value is 0 dB.
rogue-aps	Specifies the NMSP notification threshold (in dB) for rogue access points. The valid range for the threshold parameter is 0 to 10 dB, and the default value is 0 dB.
tags	Specifies the NMSP notification threshold (in dB) for RFID tags. The valid range for the threshold parameter is 0 to 10 dB, and the default value is 0 dB.
db	The valid range for the threshold parameter is 0 to 10 dB, and the default value is 0 dB.

Command Default

No default behavior or values.

Command Modes

Global configuration

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

This example shows how to configure the NMSP notification threshold to 10 dB for clients. A notification NMSP message is sent to MSE as soon as the client RSSI changes by 10 dB:

Device# configure terminal
Device(config)# location notify-threshold client 10
Device(config)# end

location plm calibrating

To configure path loss measurement (CCX S60) request for calibrating clients, use the location plm calibrating command in global configuration mode.

location plm calibrating { multiband | uniband }

Syntax Description

multiband	Specifies the path loss measurement request for calibrating clients on the associated 802.11a or 802.11b/g radio.
uniband	Specifies the path loss measurement request for calibrating clients on the associated 802.11a/b/g radio.

Command Default

No default behavior or values.

Command Modes

Global configuration

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

The uniband is useful for single radio clients (even if the radio is a dual band and can operate in the 2.4-GHz and the 5-GHz bands). The multiband is useful for multiple radio clients.

This example shows how to configure the path loss measurement request for calibrating clients on the associated 802.11a/b/g radio:

Device# configure terminal
Device(config)# location plm calibrating uniband
Device(config)# end

location rfid

To configure RFID tag tracking for a location, use the location rfid command in global configuration mode. To remove a RFID tag tracking for a location, use the no form of this command.

location rfid { status | timeout seconds | vendor-name name }

no location rfid { status | timeout seconds | vendor-name }

Syntax Description

status

Enables location tracking for RFID tags.

The no location rfid status command disables location tracking for tags.

timeout seconds

Specifies the location RFID timeout value.

Determines the amount of time for which a detected RFID location information is considered as valid. Any RSSI change (below the RSSI threshold) in the configured interval do not result in a new location computation and a message is sent to the MSE.

The valid timeout range is from 60 through 7200 seconds.

vendor-name name

Specifies the RFID tag vendor name.

Command Default

No default behavior or values.

Command Modes

Global configuration

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

The no location rfid status command disables location RFID status. The no location rfid timeout command returns to the default timeout value. The no location rfid vendor-name disables tracking for a particular vendor.

The example shows how to configure the static RFID tag data timeout:

Device# configure terminal
Device(config)# location rfid timeout 1000 
Device(config)# end

location rssi-half-life

To configure the RSSI half life for various devices, use the location rssi-half-life command in global configuration mode. To remove a RSSI half life for various devices, use the no form of this command.

location rssi-half-life { calibrating-client | client | rogue-aps | tags } seconds

no location rssi-half-life { calibrating-client | client | rogue-aps | tags }

Syntax Description

calibrating-client	Specifies the RSSI half life for calibrating clients.
client	Specifies the RSSI half life for clients.
rogue-aps	Specifies the RSSI half life for rogue access points.
tags	Specifies the RSSI half life for RFID tags.
seconds	The valid range for the half-life parameter is 0, 1, 2, 5, 10, 20, 30, 60, 90, 120, 180, or 300 seconds, and the default value is 0 seconds.

Command Default

No default behavior or values.

Command Modes

Global configuration

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

This example shows how to configure the half life value for a client RSSI to 100 seconds:

Device# configure terminal
Device(config)# location rssi-half-life client 100
Device(config)# end

mac address-table move update

To enable the MAC address table move update feature, use the mac address-table move update command in global configuration mode on the switch stack or on a standalone switch. To return to the default setting, use the no form of this command.

mac address-table move update { receive | transmit }

no mac address-table move update { receive | transmit }

Syntax Description

receive	Specifies that the switch processes MAC address-table move update messages.
transmit	Specifies that the switch sends MAC address-table move update messages to other switches in the network if the primary link goes down and the standby link comes up.

Command Default

By default, the MAC address-table move update feature is disabled.

Command Modes

Global configuration

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

The MAC address-table move update feature allows the switch to provide rapid bidirectional convergence if a primary (forwarding) link goes down and the standby link begins forwarding traffic.

You can configure the access switch to send the MAC address-table move update messages if the primary link goes down and the standby link comes up. You can configure the uplink switches to receive and process the MAC address-table move update messages.

Examples

This example shows how to configure an access switch to send MAC address-table move update messages:

Device# configure terminal
Device(config)# mac address-table move update transmit
Device(config)# end

This example shows how to configure an uplink switch to get and process MAC address-table move update messages:

Device# configure terminal
Device(config)# mac address-table move update receive
Device(config)# end

You can verify your setting by entering the show mac address-table move update privileged EXEC command.

mgmt_init

To initialize the Ethernet management port, use the mgmt_init command in boot loader mode.

mgmt_init

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

Boot loader

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

Use the mgmt_init command only during debugging of the Ethernet management port.

Example

This example shows how to initialize the Ethernet management port:

Device: mgmt_init

mkdir

To create one or more directories on the specified file system, use the mkdir command in boot loader mode.

mkdir filesystem:/directory-url...

Syntax Description

filesystem:	Alias for a file system. Use usbflash0: for USB memory sticks.
/directory-url...	Name of the directories to create. Separate each directory name with a space.

Command Default

No default behavior or values.

Command Modes

Boot loader

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

Directory names are case sensitive.

Directory names are limited to 127 characters between the slashes (/); the name cannot contain control characters, spaces, deletes, slashes, quotes, semicolons, or colons.

Example

This example shows how to make a directory called Saved_Configs:

Device: mkdir usbflash0:Saved_Configs
Directory "usbflash0:Saved_Configs" created

Related References

dir

rmdir

more

To display the contents of one or more files, use the more command in boot loader mode.

more filesystem:/file-url...

Syntax Description

filesystem:	Alias for a file system. Use flash: for the system board flash device.
/file-url...	Path (directory) and name of the files to display. Separate each filename with a space.

Command Default

No default behavior or values.

Command Modes

Boot loader

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

Filenames and directory names are case sensitive.

If you specify a list of files, the contents of each file appears sequentially.

Example

This example shows how to display the contents of a file:

Device: more flash:image_file_name
version_suffix: universal-122-xx.SEx
version_directory: image_file_name
image_system_type_id: 0x00000002
image_name: image_file_name.bin
ios_image_file_size: 8919552
total_image_file_size: 11592192
image_feature: IP|LAYER_3|PLUS|MIN_DRAM_MEG=128
image_family: family
stacking_number: 1.34
board_ids: 0x00000068 0x00000069 0x0000006a 0x0000006b 
info_end:

nmsp notification interval

To modify the Network Mobility Services Protocol (NMSP) notification interval value on the controller to address latency in the network, use the nmsp notification interval command in global configuration mode.

nmsp notification interval { attachment | location | rssi { clients | rfid | rogues { ap | client } } }

Syntax Description

attachment	Specifies the time used to aggregate attachment information.
location	Specifies the time used to aggregate location information.
rssi	Specifies the time used to aggregate RSSI information.
clients	Specifies the time interval for clients.
rfid	Specifies the time interval for rfid tags.
rogues	Specifies the time interval for rogue APs and rogue clients .
ap	Specifies the time used to aggregate rogue APs .
client	Specifies the time used to aggregate rogue clients.

Command Default

No default behavior or values.

Command Modes

Global configuration

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

This example shows how to set the NMSP notification interval for the active RFID tags to 25 seconds:


Device# configure terminal
Device(config)# nmsp notification-interval rfid 25
Device(config)# end

This example shows how to modify NMSP notification intervals for device attachment (connecting to the network or disconnecting from the network) every 10 seconds:

Device# configure terminal
Device(config)# nmsp notification-interval attachment 10
Device(config)# end

This example shows how to configure NMSP notification intervals for location parameters (location change) every 20 seconds:

Device# configure terminal
Device(config)# nmsp notification-interval location 20
Device(config)# end

no debug all

To disable debugging on a switch, use the no debug all command in Privileged EXEC mode.

no debug all

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE Release 16.1	This command was introduced.

Example

This example shows how to disable debugging on a switch.

Device: no debug all
All possible debugging has been turned off.

rename

To rename a file, use the rename command in boot loader mode.

rename filesystem:/source-file-urlfilesystem:/destination-file-url

Syntax Description

filesystem:	Alias for a file system. Use usbflash0: for USB memory sticks.
/source-file-url	Original path (directory) and filename.
/destination-file-url	New path (directory) and filename.

Command Default

No default behavior or values.

Command Modes

Boot loader

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

Filenames and directory names are case sensitive.

Directory names are limited to 127 characters between the slashes (/); the name cannot contain control characters, spaces, deletes, slashes, quotes, semicolons, or colons.

Filenames are limited to 127 characters; the name cannot contain control characters, spaces, deletes, slashes, quotes, semicolons, or colons.

Example

This example shows a file named config.text being renamed to config1.text:

Device: rename usbflash0:config.text usbflash0:config1.text

You can verify that the file was renamed by entering the dir filesystem: boot loader command.

reset

To perform a hard reset on the system, use the reset command in boot loader mode. A hard reset is similar to power-cycling the device; it clears the processor, registers, and memory.

reset

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

Boot loader

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Example

This example shows how to reset the system:

Device: reset
Are you sure you want to reset the system (y/n)? y
System resetting...

Related References

reset

test cable-diagnostics tdr

rmdir

To remove one or more empty directories from the specified file system, use the rmdir command in boot loader mode.

rmdir filesystem:/directory-url...

Syntax Description

filesystem:	Alias for a file system. Use usbflash0: for USB memory sticks.
/directory-url...	Path (directory) and name of the empty directories to remove. Separate each directory name with a space.

Command Default

No default behavior or values.

Command Modes

Boot loader

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

Directory names are case sensitive and limited to 45 characters between the slashes (/); the name cannot contain control characters, spaces, deletes, slashes, quotes, semicolons, or colons.

Before removing a directory, you must first delete all of the files in the directory.

The device prompts you for confirmation before deleting each directory.

Example

This example shows how to remove a directory:

Device: rmdir usbflash0:Test

You can verify that the directory was deleted by entering the dir filesystem: boot loader command.

Related References

dir

sdm prefer

To specify the SDM template for use on the switch, use the sdm prefer command in global configuration mode.

sdm prefer { advanced}

Syntax Description

advanced

Supports advanced features such as NetFlow.

Command Default

No default behavior or values.

Command Modes

Global configuration

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

In a device stack, all stack members must use the same SDM template that is stored on the active device.

When a new device is added to a stack, the SDM configuration that is stored on the active device overrides the template configured on an individual device.

Example

This example shows how to configure the advanced template:

Device(config)# sdm prefer advanced
Device(config)# exit
Device# reload

Related References

show sdm prefer

set

To set or display environment variables, use the set command in boot loader mode. Environment variables can be used to control the boot loader or any other software running on the device.

set variable value

Syntax Description

variable value	Use one of the following keywords for variable and the appropriate value for value: MANUAL_BOOT—Decides whether the device automatically or manually boots. Valid values are 1/Yes and 0/No. If it is set to 0 or No, the boot loader attempts to automatically boot the system. If it is set to anything else, you must manually boot the device from the boot loader mode.
	BOOT filesystem:/file-url—Identifies a semicolon-separated list of executable files to try to load and execute when automatically booting. If the BOOT environment variable is not set, the system attempts to load and execute the first executable image it can find by using a recursive, depth-first search through the flash: file system. If the BOOT variable is set but the specified images cannot be loaded, the system attempts to boot the first bootable file that it can find in the flash: file system.
	ENABLE_BREAK—Allows the automatic boot process to be interrupted when the user presses the Break key on the console. Valid values are 1, Yes, On, 0, No, and Off. If set to 1, Yes, or On, you can interrupt the automatic boot process by pressing the Break key on the console after the flash: file system has initialized.
	HELPER filesystem:/file-url—Identifies a semicolon-separated list of loadable files to dynamically load during the boot loader initialization. Helper files extend or patch the functionality of the boot loader.
	PS1 prompt—Specifies a string that is used as the command-line prompt in boot loader mode.
	CONFIG_FILE flash: /file-url—Specifies the filename that Cisco IOS uses to read and write a nonvolatile copy of the system configuration.
	BAUD rate—Specifies the number of bits per second (b/s) that is used for the baud rate for the console. The Cisco IOS software inherits the baud rate setting from the boot loader and continues to use this value unless the configuration file specifies another setting. The range is from 0 to 128000 b/s. Valid values are 50, 75, 110, 150, 300, 600, 1200, 1800, 2000, 2400, 3600, 4800, 7200, 9600, 14400, 19200, 28800, 38400, 56000, 57600, 115200, and 128000. The most commonly used values are 300, 1200, 2400, 9600, 19200, 57600, and 115200.
	SWITCH_NUMBER stack-member-number—Changes the member number of a stack member.
	SWITCH_PRIORITY priority-number—Changes the priority value of a stack member.

Command Default

The environment variables have these default values:

MANUAL_BOOT: No (0)

BOOT: Null string

ENABLE_BREAK: No (Off or 0) (the automatic boot process cannot be interrupted by pressing the Break key on the console).

HELPER: No default value (helper files are not automatically loaded).

PS1 device:

CONFIG_FILE: config.text

BAUD: 9600 b/s

SWITCH_NUMBER: 1

SWITCH_PRIORITY: 1

Note

Environment variables that have values are stored in the flash: file system in various files. Each line in the files contains an environment variable name and an equal sign followed by the value of the variable.

A variable has no value if it is not listed in these files; it has a value if it is listed even if the value is a null string. A variable that is set to a null string (for example, “ ”) is a variable with a value.

Many environment variables are predefined and have default values.

Command Modes

Boot loader

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

Environment variables are case sensitive and must be entered as documented.

Environment variables that have values are stored in flash memory outside of the flash: file system.

Under typical circumstances, it is not necessary to alter the setting of the environment variables.

The MANUAL_BOOT environment variable can also be set by using the boot manual global configuration command.

The BOOT environment variable can also be set by using the boot system filesystem:/file-url global configuration command.

The ENABLE_BREAK environment variable can also be set by using the boot enable-break global configuration command.

The HELPER environment variable can also be set by using the boot helper filesystem: / file-url global configuration command.

The CONFIG_FILE environment variable can also be set by using the boot config-file flash: /file-url global configuration command.

The SWITCH_NUMBER environment variable can also be set by using the switch current-stack-member-number renumber new-stack-member-number global configuration command.

The SWITCH_PRIORITY environment variable can also be set by using the device stack-member-number priority priority-number global configuration command.

The boot loader prompt string (PS1) can be up to 120 printable characters not including the equal sign (=).

Example

This example shows how to set the SWITCH_PRIORITY environment variable:

Device: set SWITCH_PRIORITY 2

You can verify your setting by using the set boot loader command.

Related References

reset

unset

show avc client

To display information about top number of applications, use the show avc client command in privileged EXEC mode.

show avc client client-mac top n application [ aggregate | upstream | downstream]

Syntax Description

client client-mac	Specifies the client MAC address.
top n application	Specifies the number of top "N" applications for the given client.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.3SE	This command was introduced.

The following is sample output from the show avc client command:

Device# sh avc client 0040.96ae.65ec top 10 application aggregate

Cumulative Stats:

No.  AppName      Packet-Count    Byte-Count       AvgPkt-Size     usage%
---------------------------------------------------------------------------
1    skinny          7343           449860           61             94
2    unknown         99             13631            137            3
3    dhcp            18             8752             486            2
4    http            18             3264             181            1
5    tftp            9              534              59             0
6    dns             2              224              112            0

Last Interval(90 seconds) Stats:

No.  AppName     Packet-Count     Byte-Count       AvgPkt-Size      usage%
----------------------------------------------------------------------------
1    skinny          9              540              60              100

show avc wlan

To display information about top applications and users using the applications, use the show avc wlan command in privileged EXEC mode.

show avc wlan ssid top n application [ aggregate | upstream | downstream]

Syntax Description

wlan ssid	Specifies the Service Set IDentifier (SSID) for WLAN.
top n application	Specifies the number of top "N" applications.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.3SE	This command was introduced.

The following is sample output from the show avc wlan command:

Device# show avc wlan Lobby_WLAN top 10 application aggregate

Cumulative Stats:

No.  AppName           Packet-Count          Byte-Count          AvgPkt-Size  usage%
--------------------------------------------------------------------------------------
1    ssl                10598677              1979525706            997          42
2    vnc                5550900               3764612847            678          14
3    http               3043131               2691327197            884          10
4    unknown            1856297               1140264956            614          4
5    video-over-http    1625019               2063335150            1269         8
6    binary-over-http   1329115               1744190344            1312         6
7    webex-meeting      1146872               540713787             471          2
8    rtp                923900                635650544             688          2
9    unknown            752341                911000213             1210         3
10   youtube            631085                706636186             1119         3

Last Interval(90 seconds) Stats:

No.  AppName          Packet-Count          Byte-Count            AvgPkt-Size  usage%
---------------------------------------------------------------------------------------
1    vnc                687093                602731844             877          68
2    video-over-http    213272                279831588             1312         31
3    ssl                6515                  5029365               771          1
4    webex-meeting      3649                  1722663               472          0
5    http               2634                  1334355               506          0
6    unknown            1436                  99412                 69           0
7    google-services    722                   378121                523          0
8    linkedin           655                   393263                600          0
9    exchange           432                   167390                387          0
10   gtalk-chat         330                   17330                 52           0

show cable-diagnostics tdr

To display the Time Domain Reflector (TDR) results, use the show cable-diagnostics tdr command in privileged EXEC mode.

show cable-diagnostics tdr interface interface-id

Syntax Description

interface-id

Specifies the interface on which TDR is run.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

TDR is supported only on 10/100/100 copper Ethernet ports. It is not supported on 10-Gigabit Ethernet ports and small form-factor pluggable (SFP) module ports.

Examples

This example shows the output from the show cable-diagnostics tdr interface interface-id command on a device:

Device# show cable-diagnostics tdr interface gigabitethernet1/0/23
		TDR test last run on: March 01 00:04:08 
		Interface  Speed  Local pair  Pair length         Remote pair   Pair status
		--------- ----- ---------- ------------------ ----------- --------------------
		Gi1/0/23   1000M  Pair A      1    +/- 1 meters   Pair A        Normal
		                  Pair B      1    +/- 1 meters   Pair B        Normal 
		                  Pair C      1    +/- 1 meters   Pair C        Normal 
		                  Pair D      1    +/- 1 meters   Pair D        Normal

Table 2 Field Descriptions for the show cable-diagnostics tdr Command Output
Field	Description
Interface	The interface on which TDR is run.
Speed	The speed of connection.
Local pair	The name of the pair of wires that TDR is testing on the local interface.
Pair length	The location of the problem on the cable, with respect to your device. TDR can only find the location in one of these cases: The cable is properly connected, the link is up, and the interface speed is 1000 Mb/s. The cable is open. The cable has a short.
Remote pair	The name of the pair of wires to which the local pair is connected. TDR can learn about the remote pair only when the cable is properly connected and the link is up.
Pair status	The status of the pair of wires on which TDR is running: Normal—The pair of wires is properly connected. Not completed—The test is running and is not completed. Not supported—The interface does not support TDR. Open—The pair of wires is open. Shorted—The pair of wires is shorted. ImpedanceMis—The impedance is mismatched. Short/Impedance Mismatched—The impedance mismatched or the cable is short. InProgress—The diagnostic test is in progress.

This example shows the output from the show interface interface-id command when TDR is running:

Device# show interface gigabitethernet1/0/2
		gigabitethernet1/0/2 is up, line protocol is up (connected: TDR in Progress)

This example shows the output from the show cable-diagnostics tdr interface interface-id command when TDR is not running:

Device# show cable-diagnostics tdr interface gigabitethernet1/0/2
		% TDR test was never issued on gigabitethernet1/0/2

If an interface does not support TDR, this message appears:

% TDR test is not supported on device 1

Related References

test cable-diagnostics tdr

show ap hyperlocation

To view a summary or detailed information about the hyperlocation configuration, use the show ap hyperlocation command.

show ap hyperlocation { ble-beacon | summary | detail}

Syntax Description

ble-beacon	Shows the list of configured BLE beacons.
summary	Shows the overall configuration and operational values.
detail	Shows the overall configuration and operation values as well as detailed information about each AP.

Command Default

None

Command History

Release	Modification
Cisco IOS XE Denali 16.2.1	This command was introduced.
Cisco IOS XE Denali 16.3.1	This command was modified. The ble-beacon keyword was added.

Usage Guidelines

For hyperlocation to be operational, the following conditions must be met:

At least one Cisco Connected Mobile Experiences (CMX) must be present with hyperlocation enabled.
The hyperlocation admin state should be operational.
Either AP Network Time Protocol (NTP) or IOS NTP should be configured.

Example

This example shows how to view a summary of the hyperlocation configuration:

Device# show ap hyperlocation summary

Hyperlocation operational status: Up
Hyperlocation NTP server currently used: 9.0.0.4
Hyperlocation admin status: Enabled
Hyperlocation detection threshold: -100 dBm
Hyperlocation trigger threshold: 10
Hyperlocation reset threshold: 8

This example shows how to view detailed information about hyperlocation configuration:

Device# show ap hyperlocation detail

Hyperlocation operational status: Up
Hyperlocation NTP server currently used: 9.0.0.4
Hyperlocation admin status: Enabled
Hyperlocation detection threshold: -100 dBm
Hyperlocation trigger threshold: 10
Hyperlocation reset threshold: 8

AP Name                 Radio MAC        Method    Hyperlocation
----------------------------------------------------------------
AP84b8.0252.b930        84b8.0216.c721   HALO      Enabled
AP84b8.0265.5540        84b8.0243.8796   WSM       Enabled
APf07f.0635.2d40        f07f.0676.3b89   WSM       Enabled
APf4cf.e272.4ed0        f4cf.e223.ba31   HALO      Enabled

show ap name hyperlocation

To view a summary or detailed information about the hyperlocation configuration for an access point (AP), use the show ap name hyperlocation command.

show ap name ap-name hyperlocation ble-beacon

Syntax Description

ap-name	Access point name.
hyperlocation	Displays AP hyperlocation information.
ble-beacon	Displays BLE beacon configuration of an AP.

Command Modes

Privileged EXEC (#)

Command History

Release	Modification
Cisco IOS XE Denali 16.3.1	This command was introduced.

Example

This example shows how to view the BLE beacon configuration of an AP:

Switch# show ap name test-ap hyperlocation ble-beacon

ID  Major  Minor  TX Power(dBm)
-------------------------------
0   0      0      0              
1   0      0      0              
2   0      0      0             
3   0      0      0

show ap group hyperlocation

To view a summary or detailed information of Hyperlocation configuration for an AP group, use the show ap group ap-group-name hyperlocation command.

show ap group hyperlocation { summary | detail}

Syntax Description

summary	Shows the overall configuration values (AP group specific) and operational status and parameters for the AP group.
detail	Shows both overall (AP group specific) and per-AP configuration values and operational status for the AP group. The APs listed are only those that belong to the AP group.

Command Modes

User EXEC

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE Denali 16.3.1	This command was introduced.

This example shows how to view a summary of Hyperlocation configuration for an AP group:

Device# show ap group my-ap-group hyperlocation summary

Site Name: my-ap-group
Site Description: This is an AP group
Hyperlocation operational status: Up
Reason: N/A
Hyperlocation NTP server: 9.0.0.4
Hyperlocation admin status: Enabled
Hyperlocation detection threshold: -100 dBm
Hyperlocation trigger threshold: 11
Hyperlocation reset threshold: 9

Note

For Hyperlocation to be operational, the following conditions must be met:

At least one Cisco CMX with Hyperlocation enabled
Hyperlocation admin state operational
Either AP NTP or IOS NTP configured

This example shows how to view detailed information about Hyperlocation configuration for an AP group:

Device# show ap group my-ap-group hyperlocation detail

Site Name: my-ap-group
Site Description: This is an AP group
Hyperlocation operational status: Up
Reason: N/A
Hyperlocation NTP server: 9.0.0.4
Hyperlocation admin status: Enabled
Hyperlocation detection threshold: -100 dBm
Hyperlocation trigger threshold: 11
Hyperlocation reset threshold: 9

Values for APs in all AP Groups:

AP Name                 Radio MAC        Method    Hyperlocation
----------------------------------------------------------------
APf07f.0635.2d40        f07f.0676.3b89   WSM       Enabled
APf4cf.e272.4ed0        f4cf.e223.ba31   Local     Enabled

show debug

To display all the debug commands available on a switch, use the show debug command in Privileged EXEC mode.

show debug

show debug condition Condition identifier| All conditions

Syntax Description

Condition identifier	Sets the value of the condition identifier to be used. Range is between 1 and 1000.
All conditions	Shows all conditional debugging options available.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE Release 16.1	This command was introduced.

Usage Guidelines

Because debugging output is assigned high priority in the CPU process, it can render the system unusable. For this reason, use debug commands only to troubleshoot specific problems or during troubleshooting sessions with Cisco technical support staff. Moreover, it is best to use debug commands during periods of lower network traffic and fewer users. Debugging during these periods decreases the likelihood that increased debug command processing overhead will affect system use.

Example

This example shows the output of a show debug command:

Device# show debug condition all

To disable debugging, use the no debug all command.

show env

To display fan, temperature, and power information for the switch (standalone switch, stack master, or stack member), use the show env command in EXEC modes.

show env { all | fan | power [ all | switch [ switch-number]] | stack [ stack-number] | temperature [ status] }

Syntax Description

all	Displays fan, temperature and power environmental status.
fan	Displays the switch fan status.
power	Displays the power supply status.
all	(Optional) Displays the status for all power supplies.
switch switch-number	(Optional) Displays the power supply status for a specific switch.
stack switch-number	(Optional) Displays all environmental status for each switch in the stack or for a specified switch. The range is 1 to 9, depending on the switch member numbers in the stack.
temperature	Displays the switch temperature status.
status	(Optional) Displays the temperature status and threshold values.

Command Default

No default behavior or values.

Command Modes

User EXEC

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

Use the show env stack [switch-number] command to display information about any switch in the stack from any member switch.

Use the show env temperature status command to display the switch temperature states and threshold levels.

Example

This example shows how to display information about stack member 1 from the master switch:

Device> show env stack 1
Device 1:
Device Fan 1 is OK
Device Fan 2 is OK
Device Fan 3 is OK
FAN-PS1 is OK
FAN-PS2 is NOT PRESENT
Device 1: SYSTEM TEMPERATURE is OK
Temperature Value: 32 Degree Celsius
Temperature State: GREEN
Yellow Threshold : 41 Degree Celsius
Red Threshold : 56 Degree Celsius

Device>

This example shows how to display temperature value, state, and threshold values:

Device> show env temperature status
Temperature Value: 32 Degree Celsius
Temperature State: GREEN
Yellow Threshold : 41 Degree Celsius
Red Threshold : 56 Degree Celsius

Device>

Table 3 States in the show env temperature status Command Output
State	Description
Green	The switch temperature is in the normal operating range.
Yellow	The temperature is in the warning range. You should check the external temperature around the switch.
Red	The temperature is in the critical range. The switch might not run properly if the temperature is in this range.

show env xps

To display budgeting, configuration, power, and system power information for the Cisco eXpandable Power System (XPS) 2200, use the show env xps command in privileged EXEC mode.

show env xps { budgeting | configuration | port [ all | number ] | power | system | thermal | upgrade | version }

Syntax Description

budgeting	Displays XPS power budgeting, the allocated and budgeted power of all switches in the power stack.
configuration	Displays the configuration resulting from the power xps privileged EXEC commands. The XPS configuration is stored in the XPS. Enter the show env xps configuration command to retrieve the non-default configuration.
port [all \| number ]	Displays the configuration and status of all ports or the specified XPS port. Port numbers are from 1 to 9.
power	Displays the status of the XPS power supplies.
system	Displays the XPS system status.
thermal	Displays the XPS thermal status.
upgrade	Displays the XPS upgrade status.
version	Displays the XPS version details.

Command Modes

Privileged EXEC

Command History

Release	Modification
12.2(55)SE1	This command was introduced.

Usage Guidelines

Use the show env xps privileged EXEC command to display the information for XPS 2200.

Example

This is an example of output from the show env xps budgeting command:

Switch#
=======



XPS 0101.0100.0000 :
=========================================================
Data                  Current    Power     Power Port  Switch #  PS A  PS B  Role-State Committed  
Budget
----  --------  ----  ----  ---------- ---------  ------ 1     -        -    715  SP-PS      223    
    1543
2     -        -    -    SP-PS      223       223
3     -        -    -    -          -         -
4     -        -    -    -          -         -
5     -        -    -    -          -         -
6     -        -    -    -          -         -
7     -        -    -    -          -         -
8     -        -    -    -          -         -
9     1        1100 -    RPS-NB     223        070
XPS  -        -    1100  -          -

This is an example of output from the show env xps configuration command:

Switch# show env xps configuration
=============================================
XPS 0101.0100.0000 :
=============================================
power xps port 4 priority 5
power xps port 5 mode disable
power xps port 5 priority 6
power xps port 6 priority 7
power xps port 7 priority 8
power xps port 8 priority 9
power xps port 9 priority 4

This is an example of output from the show env xps port all command:

Switch#
XPS 010



-----------------------------------------
Port name          : -
Connected          : Yes
Mode               : Enabled (On)
Priority           : 1
Data stack switch # : - Configured role    : Auto-SP
Run mode            : SP-PS : Stack Power Power-Sharing Mode
Cable faults        : 0x0 XPS 0101.0100.0000 Port 2
-----------------------------------------
Port name          : -
Connected          : Yes
Mode               : Enabled (On)
Priority           : 2
Data stack switch # : - Configured role    : Auto-SP
Run mode            : SP-PS : Stack Power Power-Sharing Mode
Cable faults        : 0x0 XPS 0101.0100.0000 Port 3
-----------------------------------------
Port name          : -
Connected          : No
Mode               : Enabled (On)
Priority           : 3
Data stack switch # : - Configured role    : Auto-SP Run mode            : -
Cable faults
<output truncated>

This is an example of output from the show env xps power command:

=============================================================================
XPS 0101.0100.0000 :
=============================================================================
Port-Supply SW PID                 Serial#     Status         Mode Watts
----------- -- ------------------  ----------- --------------  ----  -----
XPS-A           Not present
XPS-B           NG3K-PWR-1100WAC   LIT13320NTV OK             SP   1100
1-A         -  -                   -           -
1-B         -  -                   -           -               SP    715
2-A         -  -                   -           -
2-B         -  -                   -           -
9-A                       100WAC    LIT141307RK OK              RPS  1100
9-B                   esent

This is an example of output from the show env xps system command:

Switch#
=======


XPS 0101.0100.0000 :
============================================================================
XPS                        Cfg  Cfg      RPS Switch  Current    Data Port  XPS Port Name        
Mode Role    Pri Conn    Role-State  Switch #
----  --------------------  ---- -------  --- ------  ----------  --------
1     -                    On   Auto-SP  1   Yes     SP-PS      -
2     -                    On   Auto-SP  2   Yes     SP-PS      -
3     -                    On   Auto-SP  3   No      -          -
4     none                 On   Auto-SP  5   No      -          -
5     -                    Off  Auto-SP  6   No      -          -
6     -                    On   Auto-SP  7   No      -          -
7     -                    On   Auto-SP  8   No      -          -
8     -                    On   Auto-SP  9   No      -
9     test                 On   Auto-SP  4   Yes     RPS-NB

This is an example of output from the show env xps thermal command:

Switch#
=======



XPS 0101.0100.0000 :
=============================================
Fan  Status
----  -----------
1     OK
2     OK
3     NOT PRESENT PS-1  NOT PRESENT PS-2  OK Temperature is OK

This is an example of output from the show env xps upgrade command when no upgrade is occurring:

Switch# show env xps upgrade
No XPS is connected and upgrading.

These are examples of output from the show env xps upgrade command when an upgrade is in process:

Switch# show env xps upgrade
XPS Upgrade Xfer

SW Status Prog
-- ----------- ----
1 Waiting 0%
Switch#
*Mar 22 03:12:46.723: %PLATFORM_XPS-6-UPGRADE_START: XPS 0022.bdd7.9b14 upgrade has
started through the Service Port.
Switch# show env xps upgrade
XPS Upgrade Xfer
SW Status Prog
-- ----------- ----
1 Receiving 1%
Switch# show env xps upgrade
XPS Upgrade Xfer
SW Status Prog
-- ----------- ----
1 Receiving 5%
Switch# show env xps upgrade
XPS Upgrade Xfer
SW Status Prog
-- ----------- ----
1 Reloading 100%
Switch#
*Mar 22 03:16:01.733: %PLATFORM_XPS-6-UPGRADE_DONE: XPS 0022.bdd7.9b14 upgrade has
completed and the XPS is reloading.

This is an example of output from the show env xps version command:

Switch# show env xps version
=============================================
XPS 0022.bdd7.9b14:
=============================================
Serial Number: FDO13490KUT
Hardware Version: 8
Bootloader Version: 7
Software Version: 18

Table 4 Related Commands
Command	Description
power xps(global configuration command)	Configures XPS and XPS port names.
power xps(privileged EXEC command)	Configures the XPS ports and system.

show flow monitor

To display the status and statistics for a Flexible NetFlow flow monitor, use the show flow monitor command in privileged EXEC mode.

show flow monitor [ broker [ detail | picture ] | [ name ] monitor-name [ cache [ format { csv | record | table } ] ] | provisioning | statistics ]

Syntax Description

broker	(Optional) Displays information about the state of the broker for the flow monitor
detail	(Optional) Displays detailed information about the flow monitor broker.
picture	(Optional) Displays a picture of the broker state.
name	(Optional) Specifies the name of a flow monitor.
monitor-name	(Optional) Name of a flow monitor that was previously configured.
cache	(Optional) Displays the contents of the cache for the flow monitor.
format	(Optional) Specifies the use of one of the format options for formatting the display output.
csv	(Optional) Displays the flow monitor cache contents in comma-separated variables (CSV) format.
record	(Optional) Displays the flow monitor cache contents in record format.
table	(Optional) Displays the flow monitor cache contents in table format.
provisioning	(Optional) Displays the flow monitor provisioning information.
statistics	(Optional) Displays the statistics for the flow monitor.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

The cache keyword uses the record format by default.

The uppercase field names in the display output of the show flowmonitor monitor-name cache command are key fields that Flexible NetFlow uses to differentiate flows. The lowercase field names in the display output of the show flow monitor monitor-name cache command are nonkey fields from which Flexible NetFlow collects values as additional data for the cache.

The following example displays the status for a flow monitor:

Device# show flow monitor FLOW-MONITOR-1
 
Flow Monitor FLOW-MONITOR-1:
  Description:       Used for basic traffic analysis
  Flow Record:       flow-record-1
  Flow Exporter:     flow-exporter-1
                     flow-exporter-2
  Cache:
    Type:              normal
    Status:            allocated
    Size:              4096 entries / 311316 bytes
    Inactive Timeout:  15 secs
    Active Timeout:    1800 secs

This table describes the significant fields shown in the display.

Table 5 show flow monitor monitor-name Field Descriptions
Field	Description
Flow Monitor	Name of the flow monitor that you configured.
Description	Description that you configured or the monitor, or the default description User defined.
Flow Record	Flow record assigned to the flow monitor.
Flow Exporter	Exporters that are assigned to the flow monitor.
Cache	Information about the cache for the flow monitor.
Type	Flow monitor cache type. The value is always normal, as it is the only supported cache type.
Status	Status of the flow monitor cache. The possible values are: allocated—The cache is allocated. being deleted—The cache is being deleted. not allocated—The cache is not allocated.
Size	Current cache size.
Inactive Timeout	Current value for the inactive timeout in seconds.
Active Timeout	Current value for the active timeout in seconds.

The following example displays the status, statistics, and data for the flow monitor named FLOW-MONITOR-1:

Device# show flow monitor FLOW-MONITOR-1 cache
  Cache type:                               Normal (Platform cache)
  Cache size:                              Unknown
  Current entries:                               1

  Flows added:                                   3
  Flows aged:                                    2
    - Active timeout      (   300 secs)          2

DATALINK MAC SOURCE ADDRESS INPUT:       0000.0000.1000
DATALINK MAC DESTINATION ADDRESS INPUT:  6400.F125.59E6
IPV6 SOURCE ADDRESS:                     2001:DB8::1
IPV6 DESTINATION ADDRESS:                2001:DB8:1::1
TRNS SOURCE PORT:                        1111
TRNS DESTINATION PORT:                   2222
IP VERSION:                              6
IP PROTOCOL:                             6
IP TOS:                                  0x05
IP TTL:                                  11
tcp flags:                               0x20
counter bytes long:                      132059538
counter packets long:                    1158417

This table describes the significant fields shown in the display.

Table 6 show flow monitor monitor-name cache Field Descriptions
Field	Description
Cache type	Flow monitor cache type. The value is always normal, as it is the only supported cache type.
Cache Size	Number of entries in the cache.
Current entries	Number of entries in the cache that are in use.
Flows added	Flows added to the cache since the cache was created.
Flows aged	Flows expired from the cache since the cache was created.
Active timeout	Current value for the active timeout in seconds.
Inactive timeout	Current value for the inactive timeout in seconds.
DATALINK MAC SOURCE ADDRESS INPUT	MAC source address of input packets.
DATALINK MAC DESTINATION ADDRESS INPUT	MAC destination address of input packets.
IPV6 SOURCE ADDRESS	IPv6 source address.
IPV6 DESTINATION ADDRESS	IPv6 destination address.
TRNS SOURCE PORT	Source port for the transport protocol.
TRNS DESTINATION PORT	Destination port for the transport protocol.
IP VERSION	IP version.
IP PROTOCOL	Protocol number.
IP TOS	IP type of service (ToS) value.
IP TTL	IP time-to-live (TTL) value.
tcp flags	Value of the TCP flags.
counter bytes	Number of bytes that have been counted.
counter packets	Number of packets that have been counted.

The following example displays the status, statistics, and data for the flow monitor named FLOW-MONITOR-1 in a table format:

Device# show flow monitor FLOW-MONITOR-1 cache format table
  Cache type:                           Normal (Platform cache)
  Cache size:                          Unknown
  Current entries:                           1

  Flows added:                               3
  Flows aged:                                2
    - Active timeout      (   300 secs)      2

DATALINK MAC SRC ADDR INPUT  DATALINK MAC DST ADDR INPUT  IPV6 SRC ADDR  IPV6 DST ADDR  TRNS SRC PORT  TRNS DST PORT  IP VERSION  IP PROT  IP TOS  IP TTL  tcp flags  bytes long  pkts long
===========================  ===========================  =============  =============  =============  =============  ==========  =======  ======  ======  =========  ==========  =========
0000.0000.1000               6400.F125.59E6               2001:DB8::1    2001:DB8:1::1           1111           2222           6        6  0x05        11  0x20        132059538    1158417

The following example displays the status, statistics, and data for the flow monitor named FLOW-MONITOR-IPv6 (the cache contains IPv6 data) in record format:

Device# show flow monitor name FLOW-MONITOR-IPv6 cache format record
  Cache type:                               Normal (Platform cache)
  Cache size:                              Unknown
  Current entries:                               1

  Flows added:                                   3
  Flows aged:                                    2
    - Active timeout      (   300 secs)          2

DATALINK MAC SOURCE ADDRESS INPUT:       0000.0000.1000
DATALINK MAC DESTINATION ADDRESS INPUT:  6400.F125.59E6
IPV6 SOURCE ADDRESS:                     2001::2
IPV6 DESTINATION ADDRESS:                2002::2
TRNS SOURCE PORT:                        1111
TRNS DESTINATION PORT:                   2222
IP VERSION:                              6
IP PROTOCOL:                             6
IP TOS:                                  0x05
IP TTL:                                  11
tcp flags:                               0x20
counter bytes long:                      132059538
counter packets long:                    1158417

The following example displays the status and statistics for a flow monitor:

Device# show flow monitor FLOW-MONITOR-1 statistics
  Cache type:                               Normal (Platform cache)
  Cache size:                              Unknown
  Current entries:                               1

  Flows added:                                   3
  Flows aged:                                    2
    - Active timeout      (   300 secs)          2

Related References

clear flow monitor

debug flow monitor

show license right-to-use

To display detailed information for apcount adder licenses installed on the device, use the show license right-to-use command in EXEC modes.

show license right-to-use { default | detail | eula | mismatch | slot | summary | usage }

Syntax Description

default	Displays the default license information.
detail	Displays details of all the licenses in the stack.
eula	Displays the EULA text.
mismatch	Displays mismatch license information.
slot	Specifies the switch number.
summary	Displays consolidated stack-wide license information.
usage	Displays the usage details of all licenses.

Command Default

No default behavior or values.

Command Modes

User EXEC

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

The following is sample output from the show license right-to-use usage command and displays all the detailed information:

Device# show license right-to-use usage
 
 Slot#  License Name     Type     usage-duration(y:m:d)  In-Use  EULA
-----------------------------------------------------------------------
 1      ipservices     permanent    0 :0 :1                yes   yes
 1      ipbase         permanent    0 :0 :0                no    no
 1      ipbase         evaluation   0 :0 :0                no    no
 1      lanbase        permanent    0 :0 :7                no    yes
 1      apcount        evaluation   0 :0 :0                no    no
 1      apcount        base         0 :0 :0                no    no
 1      apcount        adder        0 :0 :0                no    yes
 1      apcount        adder        0 :0 :0                no    yes
 1      apcount        adder        0 :0 :0                no    yes
 1      apcount        adder        0 :0 :0                no    yes
 1      apcount        adder        0 :0 :0                no    yes


Device#

The following is sample output from the show license right-to-use detail command and displays the detailed information of licenses:

Device# show license right-to-use detail

Index 1:  License Name: apcount
           Period left: 16
           License Type: evaluation
           License State: Not Activated
           License Count: 1000
           License Location: Slot 1
Index 2:  License Name: apcount
           Period left: Lifetime
           License Type: adder
           License State: Active, In use
           License Count: 125
           License Location: Slot 1

The following is sample output from the show license right-to-use summary command when the evaluation license is active:

Device# show license right-to-use summary
  License Name    Type     Count   Period left
-----------------------------------------------
  apcount      evaluation  1000     50
 
--------------------------------------------
 
Evaluation AP-Count: Enabled
Total AP Count Licenses: 1000
AP Count Licenses In-use: 100
AP Count Licenses Remaining: 900

The following is sample output from the show license right-to-use summary command when the adder licenses are active:

Device# show license right-to-use summary
  License Name    Type     Count   Period left
-----------------------------------------------
apcount      adder       125      Lifetime
 
--------------------------------------------
 
Evaluation AP-Count: Disabled
Total AP Count Licenses: 125
AP Count Licenses In-use: 100
AP Count Licenses Remaining: 25

show location

To display location information, use the show location command in privileged EXEC mode.

show location { detail mac-addr | plm | statistics| summary rfid | rfid { client | config | detail MAC-addr | summary } }

Syntax Description

detail mac-addr	Displays detailed location information with the RSSI table for a particular client.
plm	Displays location path loss measurement (CCX S60) configuration.
statistics	Displays location-based system statistics.
summary	Displays location-based system summary information.
rfid	Displays the RFID tag tracking information.
client	Displays the summary of RFID tags that are clients.
config	Displays the configuration options for RFID tag tracking.
detail MAC-addr	Displays the detailed information for one rfid tag.
summary	Displays summary information for all known rfid tags.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

The following is sample output from the show location plm command:

Device# show location plm
Location Path Loss Configuration

Calbration client      : Disabled, Radio: Multiband
Normal clients         : Disabled
Burst interval         : 60

show location ap-detect

To display the location information detected by specified access point, use the show location ap-detect command in privileged EXEC mode.

show location ap-detect { all | client | rfid | rogue-ap | rogue-client } ap-name

Syntax Description

all	Displays information of the client, RFID, rogue access point, and rogue client.
client	Displays the client information.
rfid	Displays RFID information.
rogue-ap	Displays rogue access point information.
rogue-client	Displays rogue client information.
ap-name	Specified access point name.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

The following is sample output from the show location ap-detect client command:

Device# show location ap-detect client AP02
Clients

MAC Address       Status            Slot  Antenna     RSSI
----------------------------------------------------------
2477.0389.96ac    Associated           1        0      -60
2477.0389.96ac    Associated           1        1      -61
2477.0389.96ac    Associated           0        0      -46
2477.0389.96ac    Associated           0        1      -41


RFID Tags



Rogue AP's



Rogue Clients

MAC Address         State               Slot     Rssi
--------------------------------------------------------
0040.96b3.bce6      Alert               1        -58
586d.8ff0.891a      Alert               1        -72

show mac address-table move update

To display the MAC address-table move update information on the device, use the show mac address-table move update command in EXEC mode.

show mac address-table move update

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

User EXEC

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Example

This example shows the output from the show mac address-table move update command:


Device# show mac address-table move update

Switch-ID : 010b.4630.1780
Dst mac-address : 0180.c200.0010
Vlans/Macs supported : 1023/8320
Default/Current settings: Rcv Off/On, Xmt Off/On
Max packets per min : Rcv 40, Xmt 60
Rcv packet count : 10
Rcv conforming packet count : 5
Rcv invalid packet count : 0
Rcv packet count this min : 0
Rcv threshold exceed count : 0
Rcv last sequence# this min : 0
Rcv last interface : Po2
Rcv last src-mac-address : 0003.fd6a.8701
Rcv last switch-ID : 0303.fd63.7600
Xmt packet count : 0
Xmt packet count this min : 0
Xmt threshold exceed count : 0
Xmt pak buf unavail cnt : 0
Xmt last interface : None

show nmsp

To display the Network Mobility Services Protocol (NMSP) configuration settings, use the show nmsp command.

show nmsp { attachment | { suppress interfaces } | capability | notification interval | statistics { connection | summary } | status | subscription detail [ ip-addr ] | summary }

Syntax Description

attachment suppress interfaces	Displays attachment suppress interfaces.
capability	Displays NMSP capabilities.
notification interval	Displays the NMSP notification interval.
statistics connection	Displays all connection-specific counters.
statistics summary	Displays the NMSP counters.
status	Displays status of active NMSP connections.
subscription detail ip-addr	The details are only for the NMSP services subscribed to by a specific IP address.
subscription summary	Displays details for all of the NMSP services to which the controller is subscribed. The details are only for the NMSP services subscribed to by a specific IP address.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

The following is sample output from the show nmsp notification interval command:

Device#  show nmsp notification interval
NMSP Notification Intervals
---------------------------

RSSI Interval:
 Client               : 2 sec
 RFID                 : 2 sec
 Rogue AP             : 2 sec
 Rogue Client         : 2 sec
Attachment Interval   : 30 sec
Location Interval     : 30 sec

show platform integrity

To display checksum record for the boot stages , use the show platform integrity command in privileged EXEC mode.

show platform integrity [ sign [ nonce < nonce>]]

Syntax Description

sign	(Optional) Show signature
nonce	(Optional) Enter a nonce value

Command Modes

Privileged EXEC (#)

Command History

Release	Modification
Cisco IOS XE Denali 16.3.2	This command was introduced.

Example

This example shows how to view the checksum record for boot stages :

Device# show platform integrity sign

PCR0: EE47F8644C2887D9BD4DE3E468DD27EB93F4A606006A0B7006E2928C50C7C9AB
PCR8: E7B61EC32AFA43DA1FF4D77F108CA266848B32924834F5E41A9F6893A9CB7A38
Signature version: 1
Signature:
816C5A29741BBAC1961C109FFC36DA5459A44DBF211025F539AFB4868EF91834C05789
5DAFBC7474F301916B7D0D08ABE5E05E66598426A73E921024C21504383228B6787B74
8526A305B17DAD3CF8705BACFD51A2D55A333415CABC73DAFDEEFD8777AA77F482EC4B
731A09826A41FB3EFFC46DC02FBA666534DBEC7DCC0C029298DB8462A70DBA26833C2A
1472D1F08D721BA941CB94A418E43803699174572A5759445B3564D8EAEE57D64AE304
EE1D2A9C53E93E05B24A92387E261199CED8D8A0CE7134596FF8D2D6E6DA773757C70C
D3BA91C43A591268C248DF32658999276FB972153ABE823F0ACFE9F3B6F0AD1A00E257
4A4CC41C954015A59FB8FE
Platform: WS-C3650-12X48UZ

show platform sudi certificate

To display checksum record for the specific SUDI, use the show platform sudi certificate command in privileged EXEC mode.

show platform sudi certificate [ sign [ nonce < nonce>]]

Syntax Description

sign	(Optional) Show signature
nonce	(Optional) Enter a nonce value

Command Modes

Privileged EXEC (#)

Command History

Release	Modification
Cisco IOS XE Denali 16.3.2	This command was introduced.

Example

This example shows how to view the checksum record for a specific SUDI :

Device# show platform sudi certificate

-----BEGIN CERTIFICATE-----
MIIDQzCCAiugAwIBAgIQX/h7KCtU3I1CoxW1aMmt/zANBgkqhkiG9w0BAQUFADA1
MRYwFAYDVQQKEw1DaXNjbyBTeXN0ZW1zMRswGQYDVQQDExJDaXNjbyBSb290IENB
IDIwNDgwHhcNMDQwNTE0MjAxNzEyWhcNMjkwNTE0MjAyNTQyWjA1MRYwFAYDVQQK
Ew1DaXNjbyBTeXN0ZW1zMRswGQYDVQQDExJDaXNjbyBSb290IENBIDIwNDgwggEg
MA0GCSqGSIb3DQEBAQUAA4IBDQAwggEIAoIBAQCwmrmrp68Kd6ficba0ZmKUeIhH
xmJVhEAyv8CrLqUccda8bnuoqrpu0hWISEWdovyD0My5jOAmaHBKeN8hF570YQXJ
FcjPFto1YYmUQ6iEqDGYeJu5Tm8sUxJszR2tKyS7McQr/4NEb7Y9JHcJ6r8qqB9q
VvYgDxFUl4F1pyXOWWqCZe+36ufijXWLbvLdT6ZeYpzPEApk0E5tzivMW/VgpSdH
jWn0f84bcN5wGyDWbs2mAag8EtKpP6BrXruOIIt6keO1aO6g58QBdKhTCytKmg9l
Eg6CTY5j/e/rmxrbU6YTYK/CfdfHbBcl1HP7R2RQgYCUTOG/rksc35LtLgXfAgED
o1EwTzALBgNVHQ8EBAMCAYYwDwYDVR0TAQH/BAUwAwEB/zAdBgNVHQ4EFgQUJ/PI
FR5umgIJFq0roIlgX9p7L6owEAYJKwYBBAGCNxUBBAMCAQAwDQYJKoZIhvcNAQEF
BQADggEBAJ2dhISjQal8dwy3U8pORFBi71R803UXHOjgxkhLtv5MOhmBVrBW7hmW
Yqpao2TB9k5UM8Z3/sUcuuVdJcr18JOagxEu5sv4dEX+5wW4q+ffy0vhN4TauYuX
cB7w4ovXsNgOnbFp1iqRe6lJT37mjpXYgyc81WhJDtSd9i7rp77rMKSsH0T8lasz
Bvt9YAretIpjsJyp8qS5UwGH0GikJ3+r/+n6yUA4iGe0OcaEb1fJU9u6ju7AQ7L4
CYNu/2bPPu8Xs1gYJQk0XuPL1hS27PKSb3TkL4Eq1ZKR4OCXPDJoBYVL0fdX4lId
kxpUnwVwwEpxYB5DC2Ae/qPOgRnhCzU=
-----END CERTIFICATE-----
-----BEGIN CERTIFICATE-----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-----END CERTIFICATE-----
-----BEGIN CERTIFICATE-----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-----END CERTIFICATE-----

show sdm prefer

To display information about the templates that can be used to maximize system resources for a particular feature, use the show sdm prefer command in privileged EXEC mode. To display the current template, use the command without a keyword.

show sdm prefer [ advanced]

Syntax Description

advanced

(Optional) Displays information on the advanced template.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

If you did not reload the switch after entering the sdm prefer global configuration command, the show sdm prefer privileged EXEC command displays the template currently in use and not the newly configured template.

The numbers displayed for each template represent an approximate maximum number for each feature resource. The actual number might vary, depending on the actual number of other features configured. For example, in the default template if your device had more than 16 routed interfaces (subnet VLANs), the number of possible unicast MAC addresses might be less than 6000.

Example

The following is sample output from the show sdm prefer command:

Device# show sdm prefer

Showing SDM Template Info

This is the Advanced template.
	Number of VLANs: 																																4094
	Unicast MAC addresses:																										 32768
	Overflow Unicast MAC addresses:																	 512
	IGMP and Multicast groups: 																						8192
	Overflow IGMP and Multicast groups:													 512
	Directly connected routes: 																						32768
	Indirect routes: 																																7680
	Security Access Control Entries:																	3072
	QoS Access Control Entries: 																					3072
	Policy Based Routing ACEs: 																						1024
	Netflow ACEs: 																																			1024
	Input Microflow policer ACEs: 																			256
	Output Microflow policer ACEs: 																		256
	Flow SPAN ACEs: 																																	256
	Tunnels: 																																								256
	Control Plane Entries:																										 512
	Input Netflow flows:																												 8192
	Output Netflow flows:																										 16384
 SGT/DGT entries:                                 4096
 SGT/DGT Overflow entries:                        512
These numbers are typical for L2 and IPv4 features.
Some features such as IPv6, use up double the entry size;
so only half as many entries can be created.

Device#

Related References

sdm prefer

show tech-support wireless

To display Cisco wireless LAN controller variables frequently requested by Cisco Technical Assistance Center (TAC), use the show tech-support wireless command in privileged EXEC mode.

show tech-support wireless

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

The following is sample output from the show tech-support wireless command:

Device# show tech-support wireless
*** show ap capwap timers ***

Cisco AP CAPWAP timers

AP Discovery timer : 10
AP Heart Beat timeout : 30
Primary Discovery timer : 120
Primed Join timeout : 0
Fast Heartbeat : Disabled
Fast Heartbeat timeout : 1
*** show ap capwap retransmit ***
Global control packet retransmit interval : 3
Global control packet retransmit count : 5

AP Name Retransmit Interval Retransmit Count
------------------------------------------------------------------------------------------------
TSIM_AP-2 3 5
TSIM_AP-3 3 5
*** show ap dot11 24ghz cleanair air-quality summary ***

AQ = Air Quality
DFS = Dynamic Frequency Selection

*** show ap dot11 24ghz cleanair air-quality worst ***

AQ = Air Quality
DFS = Dynamic Frequency Selection
AP Name Channel Avg AQ Min AQ Interferers DFS
--------------------------------------------------------------
0 0 0 0 No
*** show ap dot11 24ghz cleanair config ***

Clean Air Solution............................... : Disabled
Air Quality Settings:
Air Quality Reporting........................ : Disabled
Air Quality Reporting Period (min)........... : 15
Air Quality Alarms........................... : Enabled
Air Quality Alarm Threshold.................. : 10
Interference Device Settings:
Interference Device Reporting................ : Enabled
Bluetooth Link........................... : Enabled
Microwave Oven........................... : Enabled
802.11 FH................................ : Enabled
Bluetooth Discovery...................... : Enabled
TDD Transmitter.......................... : Enabled
Jammer................................... : Enabled
Continuous Transmitter................... : Enabled
DECT-like Phone.......................... : Enabled
Video Camera............................. : Enabled
802.15.4................................. : Enabled
WiFi Inverted............................ : Enabled
WiFi Invalid Channel..................... : Enabled
SuperAG.................................. : Enabled
Canopy................................... : Enabled
Microsoft Device......................... : Enabled
WiMax Mobile............................. : Enabled
WiMax Fixed.............................. : Enabled
Interference Device Types Triggering Alarms:
Bluetooth Link........................... : Disabled
Microwave Oven........................... : Disabled
802.11 FH................................ : Disabled
Bluetooth Discovery...................... : Disabled
TDD Transmitter.......................... : Disabled
Jammer................................... : Disabled
Continuous Transmitter................... : Disabled
DECT-like Phone.......................... : Disabled
Video Camera............................. : Disabled
802.15.4................................. : Disabled
WiFi Inverted............................ : Enabled
WiFi Invalid Channel..................... : Enabled
SuperAG.................................. : Disabled
Canopy................................... : Disabled
Microsoft Device......................... : Disabled
WiMax Mobile............................. : Disabled
WiMax Fixed.............................. : Disabled
Interference Device Alarms................... : Enabled
Additional Clean Air Settings:
CleanAir Event-driven RRM State.............. : Disabled
CleanAir Driven RRM Sensitivity.............. : LOW
CleanAir Persistent Devices state............ : Disabled

show wireless band-select

To display the status of the band-select configuration, use the show wireless band-select command in privileged EXEC mode.

show wireless band-select

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

The following is sample output from the show wireless band-select command:

Device# show wireless band-select
Band Select Probe Response    : per WLAN enabling
Cycle Count                  : 2
Cycle Threshold (millisec)   : 200
Age Out Suppression (sec)    : 20
Age Out Dual Band (sec)      : 60
Client RSSI (dBm)            : 80

show wireless client calls

To display the total number of active or rejected calls on the device, use the show wireless client calls command in privileged EXEC mode.

show wireless client calls { active | rejected}

Syntax Description

active	Displays active calls.
rejected	Displays rejected calls.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

The following is sample output from the show wireless client calls command:

device# show wireless client calls active

TSPEC Calls:

----------------------------------------------------------------------------
MAC Address     AP Name             Status               WLAN  Authenticated
-----------------------------------------------------------------------------
0000.1515.000f    AP-2           Associated              1  Yes

SIP Calls:
------------------
Number of Active TSPEC calls on 802.11a and 802.11b/g: 1
Number of Active SIP calls on 802.11a and 802.11b/g: 0

show wireless client dot11

To display the total number of active or rejected calls for a specific band (2.4 Ghz or 5 Ghz), use the show wireless client dot11 command in privileged EXEC mode.

show wireless client dot11 { 24ghz | 5ghz} calls { active | rejected}

Syntax Description

24ghz	Displays the 802.11b/g network.
5ghz	Displays the 802.11a network.
calls	Displays the wireless client calls.
active	Displays active calls.
rejected	Displays rejected calls.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

The following is sample output from the show wireless client dot11 command:

Device# show wireless client dot11 5ghz calls active

 TSPEC Calls:
------------------


SIP Calls:
------------------
Number of Active TSPEC calls on 802.11a: 0
Number of Active SIP calls on 802.11a: 0

show wireless client location-calibration

To display the list of clients currently used to perform location calibration, use the show wireless client location-calibration command in privileged EXEC mode.

show wireless client location-calibration

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

The following is sample output from the show wireless client location-calibration command:

Device# show wireless client location-calibration

show wireless client probing

To display the number of probing clients, use the show wireless client probing command in privileged EXEC mode.

show wireless client probing

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

The following is sample output from the show wireless client probing command:

Device# show wireless client probing
MAC Address         
------------------
000b.cd15.0001      
000b.cd15.0002      
000b.cd15.0003      
000b.cd15.0004      
000b.cd15.0005      
000b.cd15.0006

show wireless client summary

To display a summary of active clients associated with the controller, use the show wireless client summary command in privileged EXEC mode.

show wireless client summary

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

The following is sample output from the show wireless client summary command:

Use the show wireless exclusionlist command to display clients on the exclusion list (blacklisted).

Device# show wireless client summary
Number of Local Clients : 1


MAC Address    AP Name                          WLAN State              Protocol
--------------------------------------------------------------------------------
0000.1515.000f  AP-2                        1    UP                 11a

show wireless client timers

To display 802.11 system timers, use the show wireless client timers command in privileged EXEC mode.

show wireless client timers

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

The following is sample output from the show wireless client timers command:

Device# show wireless client timers
 Authentication Response Timeout (seconds)      : 10

show wireless client voice diagnostics

To display wireless client voice diagnostic parameters, use the show wireless client voice diagnostics command in privileged EXEC mode.

show wireless client voice diagnostics { qos-map | roam-history | rssi | status | tspec}

Syntax Description

qos-map	Displays information about the QoS and DSCP mapping and packet statistics in each of the four queues: VO, VI, BE, BK. The different DSCP values are also displayed.
roam-history	Displays information about the last 3 roaming histories for each known client. The output contains the timestamp, access point associated with roaming, roaming reason, and if there is a roaming failure, a reason for the roaming failure.
rssi	Displays the client's RSSI values in the last 5 seconds when voice diagnostics are enabled.
status	Displays status of voice diagnostics for clients.
tspec	Displays voice diagnostics that are enabled for TSPEC clients.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

Debug voice diagnostics must be enabled for voice diagnostics to work.

The following is sample output from the show wireless client voice diagnostics status command:

Device# show wireless client voice diagnostics status
Voice Diagnostics Status: FALSE

show wireless country

To display the configured country and the radio types supported, use the show wireless country command in privileged EXEC mode.

show wireless country { channels | configured | supported [tx-power] }

Syntax Description

channels	Displays the list of possible channels for each band, and the list of channels allowed in the configured countries.
configured	Display configured countries.
supported tx-power	Displays the list of allowed Tx powers in each supported country.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

The following is sample output from the show wireless country channels command:

Device# show wireless country channels
  Configured Country.............................: US  - United States
      KEY: * = Channel is legal in this country and may be configured manually.
           A = Channel is the Auto-RF default in this country.
           . = Channel is not legal in this country.
           C = Channel has been configured for use by Auto-RF.
           x = Channel is available to be configured for use by Auto-RF.
         (-,-) = (indoor, outdoor) regulatory domain allowed by this country.
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
    802.11bg     :
    Channels     :                   1 1 1 1 1
                 : 1 2 3 4 5 6 7 8 9 0 1 2 3 4
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
 (-A   ,-AB  )  US  :  A * * * * A * * * * A . . .
 Auto-RF         : . . . . . . . . . . . . . .
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
 802.11a         :                         1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
 Channels        : 3 3 3 4 4 4 4 4 5 5 6 6 0 0 0 1 1 2 2 2 3 3 4 4 5 5 6 6
                 : 4 6 8 0 2 4 6 8 2 6 0 4 0 4 8 2 6 0 4 8 2 6 0 9 3 7 1 5
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
 (-A   ,-AB  )  US  :  . A . A . A . A A A A A * * * * * . . . * * * A A A A *
 Auto-RF         : . . . . . . . . . . . . . . . . . . . . . . . . . . . .
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
 4.9GHz 802.11a  :
   Channels      :                   1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2
                 : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
 US (-A   ,-AB  ): * * * * * * * * * * * * * * * * * * * A * * * * * A
 Auto-RF         : . . . . . . . . . . . . . . . . . . . . . . . . . .
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

The following is sample output from the show wireless country configured command:

Device# show wireless country configured
 Configured Country.............................: US  - United States
 Configured Country Codes
        US  - United States : 802.11a Indoor,Outdoor/ 802.11b / 802.11g

The following is sample output from the show wireless country supported tx-power command:

Device# show wireless country supported tx-power
      KEY: ##    = Tx Power in dBm.
           ##*   = Channel supports radar detection .
           .     = Channel is not legal in this country.
           (-)   = Regulatory Domains allowed by this country.
           (-,-) = (indoor, outdoor) regulatory Domains allowed by this country.
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
    802.11bg     :
    Channels     :                   1 1 1 1 1
                 : 1 2 3 4 5 6 7 8 9 0 1 2 3 4
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
 (-CE  ,-CE  )  AE  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  AL  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-AR  )  AR  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-E   )  AT  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-NA  )  AU  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-    )  BA  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  BE  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  BG  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-    )  BH  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-A   )  BO  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-A   ,-AR  )  BR  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-    )  BY  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-ABN )  CA  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-A   ,-ABN )  CA2 :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-E   )  CH  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-AER ,-AR  )  CL  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  CM  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-CE  ,-CE  )  CN  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-AR  )  CO  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-A   ,-AB  )  CR  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-E   )  CY  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  CZ  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  DE  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  DK  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-ABN )  DO  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-    )  DZ  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-AB  )  EC  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-E   )  EE  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  EG  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  ES  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  FI  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  FR  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  GB  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  GI  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  GR  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-NA  )  HK  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-    )  HR  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  HU  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-ER  )  ID  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  IE  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-EI  ,-IE  )  IL  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-I   ,-I   )  ILO :   .  .  .  . 20 20 20 20 20 20 20 20 20  .
 (-A   ,-AN  )  IN  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-E   )  IQ  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  IS  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  IT  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-JPU ,-JPU )  J2  :  23 23 23 23 23 23 23 23 23 23 23 23 23 23
 (-JPU ,-JPU )  J3  :  23 23 23 23 23 23 23 23 23 23 23 23 23 23
 (-JPQU,-PQ  )  J4  :  23 23 23 23 23 23 23 23 23 23 23 23 23 23
 (-E   ,-    )  JO  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-JPU ,-JPU )  JP  :  23 23 23 23 23 23 23 23 23 23 23 23 23 23
 (-ACE ,-ACEK)  KE  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  KN  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-ACE ,-ACEK)  KR  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  KW  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  KZ  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  LB  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  LI  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,     )  LK  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  LT  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  LU  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  LV  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  MC  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  ME  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  MK  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,     )  MO  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  MT  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-NA  )  MX  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-ACE ,-AEC )  MY  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  NL  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  NO  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-NA  )  NZ  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-E   )  OM  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-AR  )  PA  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-A   ,-AR  )  PE  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-A   ,-ABN )  PH  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-A   ,-ABN )  PH2 :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-E   )  PK  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  PL  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-A   )  PR  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-E   )  PT  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-A   )  PY  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-E   )  QA  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  RO  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  RS  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-AER ,-ER  )  RU  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-AE  ,-AE  )  SA  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  SE  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-SE  )  SG  :  20 20 20 20 20 20 20 20 20 20 20 20 20 20
 (-E   ,-E   )  SI  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  SK  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-ER  )  TH  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  TN  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-EI  ,-E   )  TR  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-ANT )  TW  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-E   )  UA  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-AB  )  US  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-A   ,-AB  )  US2 :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-A   ,-AB  )  USL :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-A   ,-    )  USX :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-A   ,-A   )  UY  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-A   ,-AR  )  VE  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-E   )  VN  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  ZA  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .

show wireless detail

To display the details of the wireless parameters configured, use the show wireless detail command in privileged EXEC mode.

show wireless detail

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

The following parameters are displayed:

The wireless user idle timeout
The controller configured RF group name
Fast SSID change

The following is sample output from the show wireless detail command:

Device# show wireless detail
User Timeout               : 300
RF network                 : default
Fast SSID                  : Disabled

show wireless dtls connections

To display the Datagram Transport Layer Security (DTLS) server status, use the show wireless dtls connections command in privileged EXEC mode.

show wireless dtls connections

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

The following is sample output from the show wireless dtls connections command:

Device# show wireless dtls connections
 AP Name         Local Port   Peer IP    Peer Port  Ciphersuite
----------------------------------------------------------------------
  AP-2       Capwap_Ctrl   10.0.0.16     52346      TLS_RSA_WITH_AES_128_CBC_SHA
  AP-3       Capwap_Ctrl   10.0.0.17     52347      TLS_RSA_WITH_AES_128_CBC_SHA

show wireless flow-control

To display the information about flow control on a particular channel, use the show wireless flow-control command in privileged EXEC mode.

show wireless flow-control channel-id

Syntax Description

channel-id

Identification number for a channel through which flow control is monitored.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.3SE	This command was introduced.

The following is sample output from the show wireless flow-control channel-id command:

Device# show wireless flow-control 3 
Channel Name                           : CAPWAP
FC State                               : Disabled
Remote Server State                    : Enabled
Pass-thru Mode                         : Disabled
EnQ Disabled                           : Disabled
Queue Depth                            : 2048
Max Retries                            : 5
Min Retry Gap (mSec)                   : 3

show wireless flow-control statistics

To display the complete information about flow control on a particular channel, use the show wireless flow-control statistics command in privileged EXEC mode.

show wireless flow-control channel-id statistics

Syntax Description

channel-id

Identification number for a channel through which flow control is monitored.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.3SE	This command was introduced.

The following is sample output from the show wireless flow-control channel-id statistics command:

Device# show wireless flow-control 3 statistics
 Channel Name                                 : CAPWAP
# of times channel went into FC               : 0
# of times channel came out of FC             : 0
Total msg count received by the FC Infra      : 1
Pass-thru msgs send count                     : 0
Pass-thru msgs fail count                     : 0
# of msgs successfully queued                 : 0
# of msgs for which queuing failed            : 0
# of msgs sent thru after queuing             : 0
# of msgs sent w/o queuing                    : 1
# of msgs for which send failed               : 0
# of invalid EAGAINS received                 : 0
Highest watermark reached                     : 0
# of times Q hit max capacity                 : 0
Avg time channel stays in FC (mSec)           : 0

show wireless load-balancing

To display the status of the load-balancing feature, use the show wireless load-balancing command in privileged EXEC mode.

show wireless load-balancing

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

The following is sample output from the show wireless load-balancing command:

 > show wireless load-balancing
Aggressive Load Balancing............................: per WLAN enabling
Aggressive Load Balancing Window (clients).................:: 5
Aggressive Load Balancing Denial Count.....................:: 3

Statistics
Total Denied Count (clients)................................:: 0
Total Denial Sent (messages)................................:: 0
Exceeded Denial Max Limit Count (times).....................:: 0
None 5G Candidate Count (times).............................:: 0
None 2.4G Candidate Count (times)...........................:: 0

show wireless performance

To display aggressive load balancing configuration, use the show wireless performance command in privileged EXEC mode.

show wireless performance { ap | client } summary

Syntax Description

ap summary	Displays aggressive load balancing configuration of access points configured to the controller.
client summary	Displays aggressive load balancing configuration details of the clients.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

The following is sample output from the show wireless performance ap summary command.

Device# show wireless performance ap summary
Number of APs:

The following is sample output from the show wireless performance client summary command.

Device# show wireless performance client summary
Number of Clients:

MAC Address        AP Name           Status        WLAN/Guest-Lan Auth Protocol Port Wired
------------------------------------------------------------------------------------------

show wireless pmk-cache

To display information about the pairwise master key (PMK) cache, use the show wireless pmk-cache command in privileged EXEC mode.

show wireless pmk-cache [ mac-address mac-addr ]

Syntax Description

mac-address mac-addr

(Optional) Information about a single entry in the PMK cache.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

The following is sample output from the show wireless pmk-cache mac-address command:

Device# show wireless pmk-cache mac-address H.H.H 
Number of PMK caches in total : 0

show wireless probe

To display the advanced probe request filtering configuration and the number of probes sent to the WLAN controller per access point per client and the probe interval in milliseconds, use the show wireless probe command in privileged EXEC mode.

show wireless probe

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

The following is sample output from the show wireless probe command:

Device# show wireless probe
Probe request filtering                          : Enabled
Number of probes per client per radio fwd from AP: 2
Probe request rate-limiting interval             : 500 msec
Aggregate probe request interval                 : 500 msec

show wireless sip preferred-call-no

To display SIP preferred call numbers, use the show wireless sip preferred-call-no command in privileged EXEC mode.

show wireless sip preferred-call-no

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

The following is sample output from the show wireless sip preferred-call-no command:

Device# show wireless sip preferred-call-no
Index Preferred-Number
----------------------
1     1031
2     1032
4     1034

show wireless summary

To display the number of access points, radios and wireless clients known to the controller, use the show wireless summary command in privileged EXEC mode.

show wireless summary

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

The following is sample output from the show wireless summary command:

Device# show wireless summary

Access Point Summary

               Total    Up    Down
-----------------------------------
802.11a/n          2     2       0
802.11b/g/n        2     2       0
All APs            2     2       0

Client Summary

Current Clients : 1
Excluded Clients: 0
Disabled Clients: 0

shutdown

To shut down VLAN switching, use the shutdown command in global configuration mode. To disable the configuration set, use the no form of this command.

shutdown [ vlan vlan-id ]

no shutdown

Syntax Description

vlan vlan-id

VLAN ID of VLAN to shutdown.

Command Default

No default behavior or values.

Command Modes

Global configuration

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Examples

This example shows how to shutdown a VLAN:

Device(config)# vlan open1
Device(config-wlan)# shutdown

This example shows that the access point is not shut down:

Device# configure terminal
Device(config)# ap name 3602a no shutdown

system env temperature threshold yellow

To configure the difference between the yellow and red temperature thresholds that determines the value of yellow threshold, use the system env temperature threshold yellow command in global configuration mode. To return to the default value, use the no form of this command.

system env temperature threshold yellow value

no system env temperature threshold yellow value

Syntax Description

value

Specifies the difference between the yellow and red threshold values (in Celsius). The range is 10 to 25.

Command Default

These are the default values

Table 7 Default Values for the Temperature Thresholds
Device	Difference between Yellow and Red	Red¹
Catalyst 3850	14°C	60°C

¹ You cannot configure the red temperature threshold.

Command Modes

Global configuration

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

You cannot configure the green and red thresholds but can configure the yellow threshold. Use the system env temperature threshold yellow value global configuration command to specify the difference between the yellow and red thresholds and to configure the yellow threshold. For example, if the red threshold is 66 degrees C and you want to configure the yellow threshold as 51 degrees C, set the difference between the thresholds as 15 by using the system env temperature threshold yellow 15 command. For example, if the red threshold is 60 degrees C and you want to configure the yellow threshold as 51 degrees C, set the difference between the thresholds as 15 by using the system env temperature threshold yellow 9 command.

Note

The internal temperature sensor in the device measures the internal system temperature and might vary ±5 degrees C.

Example

This example sets 15 as the difference between the yellow and red thresholds:

		Device(config)# system env temperature threshold yellow 15
		Device(config)#

test cable-diagnostics tdr

To run the Time Domain Reflector (TDR) feature on an interface, use the test cable-diagnostics tdr command in privileged EXEC mode.

test cable-diagnostics tdr interface interface-id

Syntax Description

interface-id

The interface on which to run TDR.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

TDR is supported only on 10/100/100 copper Ethernet ports. It is not supported on 10-Gigabit Ethernet ports or small form-factor pluggable (SFP) module ports.

After you run TDR by using the test cable-diagnostics tdr interface interface-id command, use the show cable-diagnostics tdr interface interface-id privileged EXEC command to display the results.

This example shows how to run TDR on an interface:

Device# test cable-diagnostics tdr interface gigabitethernet1/0/2
TDR test started on interface Gi1/0/2
A TDR test can take a few seconds to run on an interface
Use 'show cable-diagnostics tdr' to read the TDR results

If you enter the test cable-diagnostics tdr interface interface-id command on an interface that has an link up status and a speed of 10 or 100 Mb/s, these messages appear:

Device# test cable-diagnostics tdr interface gigabitethernet1/0/3
TDR test on Gi1/0/9 will affect link state and traffic
TDR test started on interface Gi1/0/3
A TDR test can take a few seconds to run on an interface
Use 'show cable-diagnostics tdr' to read the TDR results.

Related References

show cable-diagnostics tdr

traceroute mac

To display the Layer 2 path taken by the packets from the specified source MAC address to the specified destination MAC address, use the traceroute mac command in privileged EXEC mode.

traceroute mac [ interface interface-id ] source-mac-address [ interface interface-id ] destination-mac-address [ vlan vlan-id ] [detail]

Syntax Description

interface interface-id	(Optional) Specifies an interface on the source or destination device.
source-mac-address	The MAC address of the source device in hexadecimal format.
destination-mac-address	The MAC address of the destination device in hexadecimal format.
vlan vlan-id	(Optional) Specifies the VLAN on which to trace the Layer 2 path that the packets take from the source device to the destination device. Valid VLAN IDs are 1 to 4094.
detail	(Optional) Specifies that detailed information appears.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

For Layer 2 traceroute to function properly, Cisco Discovery Protocol (CDP) must be enabled on all of the devicees in the network. Do not disable CDP.

When the device detects a device in the Layer 2 path that does not support Layer 2 traceroute, the device continues to send Layer 2 trace queries and lets them time out.

The maximum number of hops identified in the path is ten.

Layer 2 traceroute supports only unicast traffic. If you specify a multicast source or destination MAC address, the physical path is not identified, and an error message appears.

The traceroute mac command output shows the Layer 2 path when the specified source and destination addresses belong to the same VLAN.

If you specify source and destination addresses that belong to different VLANs, the Layer 2 path is not identified, and an error message appears.

If the source or destination MAC address belongs to multiple VLANs, you must specify the VLAN to which both the source and destination MAC addresses belong.

If the VLAN is not specified, the path is not identified, and an error message appears.

The Layer 2 traceroute feature is not supported when multiple devices are attached to one port through hubs (for example, multiple CDP neighbors are detected on a port).

When more than one CDP neighbor is detected on a port, the Layer 2 path is not identified, and an error message appears.

This feature is not supported in Token Ring VLANs.

Examples

This example shows how to display the Layer 2 path by specifying the source and destination MAC addresses:

Device# traceroute mac 0000.0201.0601 0000.0201.0201
		Source 0000.0201.0601 found on con6[WS-C3750E-24PD] (2.2.6.6)
		con6 (2.2.6.6) :Gi0/0/1 => Gi0/0/3
		con5                 (2.2.5.5        )  :    Gi0/0/3 => Gi0/0/1
		con1                 (2.2.1.1        )  :    Gi0/0/1 => Gi0/0/2
		con2                 (2.2.2.2        )  :    Gi0/0/2 => Gi0/0/1
		Destination 0000.0201.0201 found on con2[WS-C3550-24] (2.2.2.2)
		Layer 2 trace completed

This example shows how to display the Layer 2 path by using the detail keyword:

Device# traceroute mac 0000.0201.0601 0000.0201.0201 detail
		Source 0000.0201.0601 found on con6[WS-C3750E-24PD] (2.2.6.6)
		con6 / WS-C3750E-24PD / 2.2.6.6 :
		        Gi0/0/2 [auto, auto] => Gi0/0/3 [auto, auto]
		con5 / WS-C2950G-24-EI / 2.2.5.5 :
		        Fa0/3 [auto, auto] => Gi0/1 [auto, auto]
		con1 / WS-C3550-12G / 2.2.1.1 :
		        Gi0/1 [auto, auto] => Gi0/2 [auto, auto]
		con2 / WS-C3550-24 / 2.2.2.2 :
		        Gi0/2 [auto, auto] => Fa0/1 [auto, auto]
		Destination 0000.0201.0201 found on con2[WS-C3550-24] (2.2.2.2)
		Layer 2 trace completed.

This example shows how to display the Layer 2 path by specifying the interfaces on the source and destination devicees:

Device# traceroute mac interface fastethernet0/1 0000.0201.0601 interface fastethernet0/3 0000.0201.0201
		Source 0000.0201.0601 found on con6[WS-C3750E-24PD] (2.2.6.6)
		con6 (2.2.6.6) :Gi0/0/1 => Gi0/0/3
		con5                 (2.2.5.5        )  :    Gi0/0/3 => Gi0/0/1
		con1                 (2.2.1.1        )  :    Gi0/0/1 => Gi0/0/2
		con2                 (2.2.2.2        )  :    Gi0/0/2 => Gi0/0/1
		Destination 0000.0201.0201 found on con2[WS-C3550-24] (2.2.2.2)
		Layer 2 trace completed

This example shows the Layer 2 path when the device is not connected to the source device:

Device# traceroute mac 0000.0201.0501 0000.0201.0201 detail
		Source not directly connected, tracing source .....
		Source 0000.0201.0501 found on con5[WS-C3750E-24TD] (2.2.5.5)
		con5 / WS-C3750E-24TD / 2.2.5.5 :
		        Gi0/0/1 [auto, auto] => Gi0/0/3 [auto, auto]
		con1 / WS-C3550-12G / 2.2.1.1 :
		        Gi0/1 [auto, auto] => Gi0/2 [auto, auto]
		con2 / WS-C3550-24 / 2.2.2.2 :
		        Gi0/2 [auto, auto] => Fa0/1 [auto, auto]
		Destination 0000.0201.0201 found on con2[WS-C3550-24] (2.2.2.2)
		Layer 2 trace completed.

This example shows the Layer 2 path when the device cannot find the destination port for the source MAC address:

Device# traceroute mac 0000.0011.1111 0000.0201.0201
		Error:Source Mac address not found. 
		Layer2 trace aborted.

This example shows the Layer 2 path when the source and destination devices are in different VLANs:

Device# traceroute mac 0000.0201.0601 0000.0301.0201
		Error:Source and destination macs are on different vlans. 
		Layer2 trace aborted.

This example shows the Layer 2 path when the destination MAC address is a multicast address:

Device# traceroute mac 0000.0201.0601 0100.0201.0201
  Invalid destination mac address

This example shows the Layer 2 path when source and destination devicees belong to multiple VLANs:

Device# traceroute mac 0000.0201.0601 0000.0201.0201
		Error:Mac found on multiple vlans.
		Layer2 trace aborted.

Related References

traceroute mac ip

To display the Layer 2 path taken by the packets from the specified source IP address or hostname to the specified destination IP address or hostname, use the traceroute mac ip command in privileged EXEC mode.

traceroute mac ip { source-ip-address | source-hostname } { destination-ip-address | destination-hostname } [detail]

Syntax Description

source-ip-address	The IP address of the source device as a 32-bit quantity in dotted-decimal format.
source-hostname	The IP hostname of the source device.
destination-ip-address	The IP address of the destination device as a 32-bit quantity in dotted-decimal format.
destination-hostname	The IP hostname of the destination device.
detail	(Optional) Specifies that detailed information appears.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

For Layer 2 traceroute to function properly, Cisco Discovery Protocol (CDP) must be enabled on each device in the network. Do not disable CDP.

When the device detects a device in the Layer 2 path that does not support Layer 2 traceroute, the device continues to send Layer 2 trace queries and lets them time out.

The maximum number of hops identified in the path is ten.

The traceroute mac ip command output shows the Layer 2 path when the specified source and destination IP addresses are in the same subnet.

When you specify the IP addresses, the device uses Address Resolution Protocol (ARP) to associate the IP addresses with the corresponding MAC addresses and the VLAN IDs.

If an ARP entry exists for the specified IP address, the device uses the associated MAC address and identifies the physical path.
If an ARP entry does not exist, the device sends an ARP query and tries to resolve the IP address. The IP addresses must be in the same subnet. If the IP address is not resolved, the path is not identified, and an error message appears.

The Layer 2 traceroute feature is not supported when multiple devices are attached to one port through hubs (for example, multiple CDP neighbors are detected on a port).

When more than one CDP neighbor is detected on a port, the Layer 2 path is not identified, and an error message appears.

This feature is not supported in Token Ring VLANs.

Examples

This example shows how to display the Layer 2 path by specifying the source and destination IP addresses and by using the detail keyword:

		Device# traceroute mac ip 2.2.66.66 2.2.22.22 detail
  Translating IP to mac ..... 
		2.2.66.66 => 0000.0201.0601
		2.2.22.22 => 0000.0201.0201
		
		Source 0000.0201.0601 found on con6[WS-C2950G-24-EI] (2.2.6.6)
		con6 / WS-C3750E-24TD / 2.2.6.6 :
		        Gi0/0/1 [auto, auto] => Gi0/0/3 [auto, auto]
		con5 / WS-C2950G-24-EI / 2.2.5.5 :
		        Fa0/3 [auto, auto] => Gi0/1 [auto, auto]
		con1 / WS-C3550-12G / 2.2.1.1 :
		        Gi0/1 [auto, auto] => Gi0/2 [auto, auto]
		con2 / WS-C3550-24 / 2.2.2.2 :
		        Gi0/2 [auto, auto] => Fa0/1 [auto, auto]
		Destination 0000.0201.0201 found on con2[WS-C3550-24] (2.2.2.2)
		Layer 2 trace completed.

This example shows how to display the Layer 2 path by specifying the source and destination hostnames:

		Device# traceroute mac ip con6 con2
		Translating IP to mac ..... 
		2.2.66.66 => 0000.0201.0601
		2.2.22.22 => 0000.0201.0201
		
		Source 0000.0201.0601 found on con6
		con6 (2.2.6.6) :Gi0/0/1 => Gi0/0/3
		con5                 (2.2.5.5        )  :    Gi0/0/3 => Gi0/1
		con1                 (2.2.1.1        )  :    Gi0/0/1 => Gi0/2
		con2                 (2.2.2.2        )  :    Gi0/0/2 => Fa0/1
		Destination 0000.0201.0201 found on con2
		Layer 2 trace completed

This example shows the Layer 2 path when ARP cannot associate the source IP address with the corresponding MAC address:

		Device# traceroute mac ip 2.2.66.66 2.2.77.77
		Arp failed for destination 2.2.77.77.
		Layer2 trace aborted.

Related References

traceroute mac

trapflags

To enable sending rogue access point detection traps, use the trapflags command in privileged EXEC mode. To disable sending rogue access point detection traps, use the no form of this command.

trapflags rogueap

no trapflags rogueap

Syntax Description

rogueap

Enables sending rogue access point detection traps.

Command Default

Enabled.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

This example shows how to disable the sending of rogue access point detection traps:

Device# configure terminal
Device(config)# no trapflags rogueap
Device(config)# end

trapflags client

To enable the sending of client-related DOT11 traps, use the trapflags client command in privileged EXEC mode. To disable the sending of client-related DOT11 traps, use the no form of this command.

trapflags client [ dot11 { assocfail | associate | authfail | deauthenticate | disassociate } | excluded ]

no trapflags client [ dot11 { assocfail | associate | authfail | deauthenticate | disassociate } | excluded ]

Syntax Description

dot11	Client-related DOT11 traps.
assocfail	Enables the sending of Dot11 association fail traps to clients.
associate	Enables the sending of Dot11 association traps to clients.
authfail	Enables the sending of Dot11 authentication fail traps to clients.
deauthenticate	Enables the sending of Dot11 deauthentication traps to clients.
disassociate	Enables the sending of Dot11 disassociation traps to clients.
excluded	Enables the sending of excluded trap to clients.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

This example shows how to enable the sending of Dot11 disassociation trap to clients:

Device# configure terminal
Device(config)# trapflags client dot11 disassociate
Device(config)# end

type

To display the contents of one or more files, use the type command in boot loader mode.

type filesystem:/file-url...

Syntax Description

filesystem:	Alias for a file system. Use flash: for the system board flash device; use usbflash0: for USB memory sticks.
/file-url...	Path (directory) and name of the files to display. Separate each filename with a space.

Command Default

No default behavior or values.

Command Modes

Boot loader

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

Filenames and directory names are case sensitive.

If you specify a list of files, the contents of each file appear sequentially.

Example

This example shows how to display the contents of a file:

Device: type flash:image_file_name
version_suffix: universal-122-xx.SEx
version_directory: image_file_name
image_system_type_id: 0x00000002
image_name: image_file_name.bin
ios_image_file_size: 8919552
total_image_file_size: 11592192
image_feature: IP|LAYER_3|PLUS|MIN_DRAM_MEG=128
image_family: family
stacking_number: 1.34
board_ids: 0x00000068 0x00000069 0x0000006a 0x0000006b 
info_end:

unset

To reset one or more environment variables, use the unset command in boot loader mode.

unset variable...

Syntax Description

variable	Use one of these keywords for variable: MANUAL_BOOT—Specifies whether the device automatically or manually boots.
	BOOT—Resets the list of executable files to try to load and execute when automatically booting. If the BOOT environment variable is not set, the system attempts to load and execute the first executable image it can find by using a recursive, depth-first search through the flash: file system. If the BOOT variable is set but the specified images cannot be loaded, the system attempts to boot the first bootable file that it can find in the flash: file system.
	ENABLE_BREAK—Specifies whether the automatic boot process can be interrupted by using the Break key on the console after the flash: file system has been initialized.
	HELPER—Identifies the semicolon-separated list of loadable files to dynamically load during the boot loader initialization. Helper files extend or patch the functionality of the boot loader.
	PS1—Specifies the string that is used as the command-line prompt in boot loader mode.
	CONFIG_FILE—Resets the filename that Cisco IOS uses to read and write a nonvolatile copy of the system configuration.
	BAUD—Resets the rate in bits per second (b/s) used for the console. The Cisco IOS software inherits the baud rate setting from the boot loader and continues to use this value unless the configuration file specifies another setting.

Command Default

No default behavior or values.

Command Modes

Boot loader

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

Under typical circumstances, it is not necessary to alter the setting of the environment variables.

The MANUAL_BOOT environment variable can also be reset by using the no boot manual global configuration command.

The BOOT environment variable can also be reset by using the no boot system global configuration command.

The ENABLE_BREAK environment variable can also be reset by using the no boot enable-break global configuration command.

The HELPER environment variable can also be reset by using the no boot helper global configuration command.

The CONFIG_FILE environment variable can also be reset by using the no boot config-file global configuration command.

Example

This example shows how to unset the SWITCH_PRIORITY environment variable:

Device: unset SWITCH_PRIORITY

Related References

set

reset

version

To display the boot loader version, use the version command in boot loader mode.

version

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

Boot loader

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Example

This example shows how to display the boot loader version on a device:



Device: version
CAT3K_CAA Boot Loader (CAT3K_CAA-HBOOT-M) Version 1.3, RELEASE SOFTWARE (P) 
Compiled Sun Jun 16 18:31:15 PDT 2013 by rel

wireless client

To configure client parameters, use the wireless client command in global configuration mode.

wireless client { association limit assoc-number interval interval | band-select { client-rssi rssi | cycle-count count | cycle-threshold threshold | expire dual-band timeout | expire suppression timeout } | max-user-login max-user-login | timers auth-timeout seconds | user-timeout user-timeout }

Syntax Description

association limit assoc-number interval interval	Enables association request limit per access point slot at a given interval and configures the association request limit interval. You can configure number of association request per access point slot at a given interval from one through 100. You can configure client association request limit interval from 100 through 10000 milliseconds.
band-select	Configures the band select options for the client.
client-rssi rssi	Sets the client received signal strength indicator (RSSI) threshold for band select. The minimum dBm of a client RSSI to respond to probe is between -90 and -20.
cycle-count count	Sets the band select probe cycle count. You can configure the cycle count from 1 to 10.
cycle-threshold threshold	Sets the time threshold for a new scanning cycle. You can configure the cycle threshold from 1 to 1000 milliseconds.
expire dual-band timeout	Sets the timeout before stopping to try to push a given client to the 5-GHz band. You can configure the timeout from 10 to 300 seconds, and the default value is 60 seconds.
expire suppression timeout	Sets the expiration time for pruning previously known dual-band clients. You can configure the suppression from 10 to 200 seconds, and the default timeout value is 20 seconds.
max-user-login max-user-login	Configures the maximum number of login sessions for a user.
timers auth-timeout seconds	Configures the client timers.
user-timeout user-timeout	Configures the idle client timeout.

Command Default

No default behavior or values.

Command Modes

Global configuration

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

This example shows how to set the proble cycle count for band select to 8:

Device# configure terminal
Device(config)# wireless client band-select cycle-count 8 
Device(config)# end

This example shows how to set the time threshold for a new scanning cycle with threshold value of 700 milliseconds:

Device# configure terminal
Device(config)# wireless client band-select cycle-threshold 700
Device(config)# end

This example shows how to suppress dual-band clients from the dual-band database after 70 seconds:

Device# configure terminal
Device(config)# wireless client band-select expire suppression 70
Device(config)# end

wireless client mac-address deauthenticate

To disconnect a wireless client, use the wireless client mac-address deauthenticate command in global configuration mode.

wirelessclientmac-address mac-addr deauthenticate

Syntax Description

mac-address mac-addr

Wireless client MAC address.

Command Default

No default behavior or values.

Command Modes

Global configuration

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

This example shows how to disconnect a wireless client:

Device# configure terminal
Device(config)# wireless client mac-address 00:1f:ca:cf:b6:60 deauthenticate   
Device(config)# end

wireless client mac-address

To configure the wireless client settings, use the wireless client mac-address command in global configuration mode.

wireless client mac-address mac-addr ccx { clear-reports | clear-results | default-gw-ping | dhcp-test | dns-ping | dns-resolve hostname host-name | get-client-capability | get-manufacturer-info | get-operating-parameters | get-profiles | log-request { roam | rsna | syslog } | send-message message-id | stats-request measurement-duration { dot11 | security } | test-abort | test-association ssid bssid dot11 channel | test-dot1x [profile-id] bssid dot11 channel | test-profile { any | profile-id } }

Syntax Description

mac-addr

MAC address of the client.

ccx

Cisco client extension (CCX).

clear-reports

Clears the client reporting information.

clear-results

Clears the test results on the controller.

default-gw-ping

Sends a request to the client to perform the default gateway ping test.

dhcp-test

Sends a request to the client to perform the DHCP test.

dns-ping

Sends a request to the client to perform the Domain Name System (DNS) server IP address ping test.

dns-resolve hostname host-name

Sends a request to the client to perform the Domain Name System (DNS) resolution test to the specified hostname.

get-client-capability

Sends a request to the client to send its capability information.

get-manufacturer-info

Sends a request to the client to send the manufacturer's information.

get-operating-parameters

Sends a request to the client to send its current operating parameters.

get-profiles

Sends a request to the client to send its profiles.

log-request

Configures a CCX log request for a specified client device.

roam

(Optional) Specifies the request to specify the client CCX roaming log

rsna

(Optional) Specifies the request to specify the client CCX RSNA log.

syslog

(Optional) Specifies the request to specify the client CCX system log.

send-message message-id

Sends a message to the client.

Message type that involves one of the following:

1—The SSID is invalid
2—The network settings are invalid.
3—There is a WLAN credibility mismatch.
4—The user credentials are incorrect.
5—Please call support.
6—The problem is resolved.
7—The problem has not been resolved.
8—Please try again later.
9—Please correct the indicated problem.
10—Troubleshooting is refused by the network.
11—Retrieving client reports.
12—Retrieving client logs.
13—Retrieval complete.
14—Beginning association test.
15—Beginning DHCP test.
16—Beginning network connectivity test.
17—Beginning DNS ping test.
18—Beginning name resolution test.
19—Beginning 802.1X authentication test.
20—Redirecting client to a specific profile.
21—Test complete.
22—Test passed.
23—Test failed.
24—Cancel diagnostic channel operation or select a WLAN profile to resume normal operation.
25—Log retrieval refused by the client.
26—Client report retrieval refused by the client.
27—Test request refused by the client.
28—Invalid network (IP) setting.
29—There is a known outage or problem with the network.
30—Scheduled maintenance period.
31—The WLAN security method is not correct.
32—The WLAN encryption method is not correct.
33—The WLAN authentication method is not correct.

stats-request measurement-duration

Senda a request for statistics.

dot11

Optional) Specifies dot11 counters.

security

(Optional) Specifies security counters.

test-abort

Sends a request to the client to abort the current test.

test-association ssid bssid dot11 channel

Sends a request to the client to perform the association test.

test-dot1x

Sends a request to the client to perform the 802.1x test.

profile-id

(Optional) Test profile name.

bssid

Basic SSID.

dot11

Specifies the 802.11a, 802.11b, or 802.11g network.

channel

Channel number.

test-profile

Sends a request to the client to perform the profile redirect test.

any

Sends a request to the client to perform the profile redirect test.

profile-id

Test profile name.

Note

The profile ID should be from one of the client profiles for which client reporting is enabled.

Command Default

No default behavior or values.

Command Modes

Global configuration

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

The default-gw-ping test does not require the client to use the diagnostic channel.

This example shows how to clear the reporting information of the client MAC address 00:1f:ca:cf:b6:60:

Device# configure terminal
Device(config)# wireless client mac-address 00:1f:ca:cf:b6:60 ccx clear-reports 
Device(config)# end

wireless load-balancing

To globally configure aggressive load balancing on the controller, use the wireless load-balancing command in global configuration mode.

wireless load-balancing { denial denial-count | window client-count }

Syntax Description

denial denial-count

Specifies the number of association denials during load balancing.

Maximum number of association denials during load balancing is from 1 to 10 and the default value is 3.

window client-count

Specifies the aggressive load balancing client window, with the number of clients needed to trigger aggressive load balancing on a given access point.

Aggressive load balancing client window with the number of clients is from 0 to 20 and the default value is 5.

Command Default

Disabled.

Command Modes

Global configuration

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

Load-balancing-enabled WLANs do not support time-sensitive applications like voice and video because of roaming delays.

When you use Cisco 7921 and 7920 Wireless IP Phones with controllers, make sure that aggressive load balancing is disabled on the voice WLANs for each controller. Otherwise, the initial roam attempt by the phone might fail, causing a disruption in the audio path.

This example shows how to configure association denials during load balancing:

Device# configure terminal
Device(config)# wireless load-balancing denial 5
Device(config)# end

wireless sip preferred-call-no

To add a new preferred call or configure voice prioritization, use the wireless sip preferred-call-no command in global configuration mode. To remove a preferred call, use the no form of this command.

wireless sip preferred-call-no callIndex call-no

no wireless sip preferred-call-no callIndex

Syntax Description

callIndex	Call index with valid values between 1 and 6.
call-no	Preferred call number that can contain up to 27 characters.

Command Default

No default behavior or values.

Command Modes

Global configuration

Command History

Release	Modification
Cisco IOS XE 3.2SE	This command was introduced.

Usage Guidelines

Before you configure voice prioritization, you must complete the following prerequisites:

Set WLAN QoS to allow voice calls to pass through.
Enable ACM for the radio.
Enable SIP call snooping on the WLAN.

This example shows how to add a new preferred call or configure voice prioritization:

Device# configure terminal
Device(config)# wireless sip preferred-call-no 2 0123456789
Device(config)# end

Bias-Free Language

Results

Chapter: System Management

System Management

ap hyperlocation

Syntax Description

Command History

ap name hyperlocation

Syntax Description

Command Default

Command Modes

Command History

Example

hyperlocation

Syntax Description

Command Modes

Command History

ap ntp ip

Syntax Description

Command History

ntp ip

Syntax Description

Command Modes

Command History

arp

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Example

boot

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Example

cat

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Example

clear location

Syntax Description

Command Default

Command Modes

Command History

clear location statistics

Syntax Description

Command Default

Command Modes

Command History

clear nmsp statistics

Syntax Description

Command Default

Command Modes

Command History

clear wireless ccx statistics

Syntax Description

Command Default

Command Modes

Command History

clear wireless client tsm dot11

Syntax Description

Command Default

Command Modes

Command History

clear wireless location s69 statistics

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Example

copy

Syntax Description