Consolidated Platform Configuration Guide, Cisco IOS XE 15.2(5)E (Catalyst 2960-XR Switch)

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Book Contents
Find Matches in This Book

Results

Updated:
October 15, 2019

Chapter: Configuring IPv6 ACL

Configuring IPv6 ACL

Information About Configuring IPv6 ACLs

You can filter IP version 6 (IPv6) traffic by creating IPv6 access control lists (ACLs) and applying them to interfaces similarly to the way that you create and apply IP version 4(IPv4) named ACLs. You can also create and apply input router ACLs to filter Layer 3 management traffic.


Note
To use IPv6, you must configure the dual IPv4 and IPv6 Switch Database Management (SDM) template on the switch. You select the template by entering the sdm prefer {default } global configuration command.

Understanding IPv6 ACLs

A switch image supports two types of IPv6 ACLs:

  • IPv6 router ACLs - Supported on inbound or outbound traffic on Layer 3 interfaces, which can be routed ports, switch virtual interfaces (SVIs), or Layer 3 EtherChannels. Applied to only IPv6 packets that are routed.
  • IPv6 port ACLs - Supported on inbound traffic on Layer 2 interfaces only. Applied to all IPv6 packets entering the interface.

Note
If you configure unsupported IPv6 ACLs, an error message appears and the configuration does not take affect.

The switch does not support VLAN ACLs (VLAN maps) for IPv6 traffic.

You can apply both IPv4 and IPv6 ACLs to an interface.

As with IPv4 ACLs, IPv6 port ACLs take precedence over router ACLs:

  • When an input router ACL and input port ACL exist in an SVI, packets received on ports to which a port ACL is applied are filtered by the port ACL. Routed IP packets received on other ports are filtered by the router ACL. Other packets are not filtered.

  • When an output router ACL and input port ACL exist in an SVI, packets received on the ports to which a port ACL is applied are filtered by the port ACL. Outgoing routed IPv6 packets are filtered by the router ACL. Other packets are not filtered.


Note
If any port ACL (IPv4, IPv6, or MAC) is applied to an interface, that port ACL is used to filter packets, and any router ACLs attached to the SVI of the port VLAN are ignored.

Supported ACL Features

IPv6 ACLs on the switch have these characteristics:

  • Fragmented frames (the fragments keyword as in IPv4) are supported.

  • The same statistics supported in IPv4 are supported for IPv6 ACLs.

  • If the switch runs out of TCAM space, packets associated with the ACL label are forwarded to the CPU, and the ACLs are applied in software.

  • Routed or bridged packets with hop-by-hop options have IPv6 ACLs applied in software.

  • Logging is supported for router ACLs, but not for port ACLs.

IPv6 ACL Limitations

With IPv4, you can configure standard and extended numbered IP ACLs, named IP ACLs, and MAC ACLs. IPv6 supports only named ACLs.

The switch supports most Cisco IOS-supported IPv6 ACLs with some exceptions:

  • IPv6 source and destination addresses-ACL matching is supported only on prefixes from /0 to /64 and host addresses (/128) that are in the extended universal identifier (EUI)-64 format. The switch supports only these host addresses with no loss of information:

    -aggregatable global unicast addresses

    -link local addresses

  • The switch does not support matching on these keywords: flowlabel, routing header, and undetermined-transport.

  • The switch does not support reflexive ACLs (the reflect keyword).

  • This release supports only port ACLs and router ACLs for IPv6; it does not support VLAN ACLs (VLAN maps).

  • The switch does not apply MAC-based ACLs on IPv6 frames.

  • You cannot apply IPv6 port ACLs to Layer 2 EtherChannels.

  • The switch does not support output port ACLs.

  • Output router ACLs and input port ACLs for IPv6 are supported only on . Switches support only control plane (incoming) IPv6 ACLs.

  • When configuring an ACL, there is no restriction on keywords entered in the ACL, regardless of whether or not they are supported on the platform. When you apply the ACL to an interface that requires hardware forwarding (physical ports or SVIs), the switch checks to determine whether or not the ACL can be supported on the interface. If not, attaching the ACL is rejected.

  • If an ACL is applied to an interface and you attempt to add an access control entry (ACE) with an unsupported keyword, the switch does not allow the ACE to be added to the ACL that is currently attached to the interface.

Configuring IPv6 ACLs

To filter IPv6 traffic, you perform these steps:

Before you begin

Before configuring IPv6 ACLs, you must select one of the dual IPv4 and IPv6 SDM templates.

Procedure

  Command or Action Purpose
Step 1

Create an IPv6 ACL, and enter IPv6 access list configuration mode.

Step 2

Configure the IPv6 ACL to block (deny) or pass (permit) traffic.

Step 3

Apply the IPv6 ACL to an interface. For router ACLs, you must also configure an IPv6 address on the Layer 3 interface to which the ACL is applied.

Default IPv6 ACL Configuration

There are no IPv6 ACLs configured or applied.

Interaction with Other Features and Switches

  • If an IPv6 router ACL is configured to deny a packet, the packet is not routed. A copy of the packet is sent to the Internet Control Message Protocol (ICMP) queue to generate an ICMP unreachable message for the frame.

  • If a bridged frame is to be dropped due to a port ACL, the frame is not bridged.

  • You can create both IPv4 and IPv6 ACLs on a switch or switch stack, and you can apply both IPv4 and IPv6 ACLs to the same interface. Each ACL must have a unique name; an error message appears if you try to use a name that is already configured.

    You use different commands to create IPv4 and IPv6 ACLs and to attach IPv4 or IPv6 ACLs to the same Layer 2 or Layer 3 interface. If you use the wrong command to attach an ACL (for example, an IPv4 command to attach an IPv6 ACL), you receive an error message.

  • You cannot use MAC ACLs to filter IPv6 frames. MAC ACLs can only filter non-IP frames.

  • If the hardware memory is full, for any additional configured ACLs, packets are dropped to the CPU, and the ACLs are applied in software. When the hardware is full a message is printed to the console indicating the ACL has been unloaded and the packets will be dropped on the interface.


    Note
    Only packets of the same type as the ACL that could not be added (ipv4, ipv6, MAC) will be dropped on the interface.

Creating an IPv6 ACL

Procedure

  Command or Action Purpose
Step 1

enable

Example:


Switch> enable

Enables privileged EXEC mode.

Enter your password if prompted.

Step 2

configure terminal

Example:


Switch# configure terminal

Enters global configuration mode.

Step 3

ipv6 access-list acl_name

Example:

Switch# ipv6 access-list access-list-name

Use a name to define an IPv6 access list and enter IPv6 access-list configuration mode.

Step 4

{deny|permit} protocol

Example:

{deny | permit} protocol {source-ipv6-prefix/prefix-length | any | host source-ipv6-address}
[operator [port-number]]{destination-ipv6-prefix/prefix-length | any |host destination-ipv6-address}
[operator [port-number]][dscp value] [fragments][log] [log-input] [routing][sequence value]
[time-range name]

Enter deny or permit to specify whether to deny or permit the packet if conditions are matched. These are the conditions:

  • For protocol, enter the name or number of an Internet protocol: ahp, esp, icmp, ipv6, pcp, stcp, tcp, or udp, or an integer in the range 0 to 255 representing an IPv6 protocol number.

  • The source-ipv6-prefix/prefix-length or destination-ipv6-prefix/ prefix-length is the source or destination IPv6 network or class of networks for which to set deny or permit conditions, specified in hexadecimal and using 16-bit values between colons (see RFC 2373).

  • Enter any as an abbreviation for the IPv6 prefix ::/0.

  • For host source-ipv6-address or destination-ipv6-address, enter the source or destination IPv6 host address for which to set deny or permit conditions, specified in hexadecimal using 16-bit values between colons.

  • (Optional) For operator, specify an operand that compares the source or destination ports of the specified protocol. Operands are lt (less than), gt (greater than), eq (equal), neq (not equal), and range.

If the operator follows the source-ipv6-prefix/prefix-length argument, it must match the source port. If the operator follows the destination-ipv6- prefix/prefix-length argument, it must match the destination port.

  • (Optional) The port-number is a decimal number from 0 to 65535 or the name of a TCP or UDP port. You can use TCP port names only when filtering TCP. You can use UDP port names only when filtering UDP.

  • (Optional) Enter dscp value to match a differentiated services code point value against the traffic class value in the Traffic Class field of each IPv6 packet header. The acceptable range is from 0 to 63.

  • (Optional) Enter fragments to check noninitial fragments. This keyword is visible only if the protocol is ipv6.

  • (Optional) Enter log to cause an logging message to be sent to the console about the packet that matches the entry. Enter log-input to include the input interface in the log entry. Logging is supported only for router ACLs.

  • (Optional) Enter routing to specify that IPv6 packets be routed.

  • (Optional) Enter sequence value to specify the sequence number for the access list statement. The acceptable range is from 1 to 4294967295

  • (Optional) Enter time-range name to specify the time range that applies to the deny or permit statement.

Step 5

{deny|permit} tcp

Example:

{deny | permit} tcp {source-ipv6-prefix/prefix-length | any | hostsource-ipv6-address}
[operator [port-number]]{destination-ipv6-prefix/prefix-length | any |hostdestination-ipv6-address}
[operator [port-number]][ack] [dscp value][established] [fin] 
[log][log-input] [neq {port |protocol}] [psh] [range{port | protocol}] [rst][routing] [sequence value]
[syn] [time-range name][urg]

(Optional) Define a TCP access list and the access conditions.

Enter tcp for Transmission Control Protocol. The parameters are the same as those described in Step 3, with these additional optional parameters:

  • ack—Acknowledgment bit set.

  • established—An established connection. A match occurs if the TCP datagram has the ACK or RST bits set.

  • fin—Finished bit set; no more data from sender.

  • neq {port | protocol}—Matches only packets that are not on a given port number.

  • psh—Push function bit set.

  • range {port | protocol}—Matches only packets in the port number range.

  • rst—Reset bit set.

  • syn—Synchronize bit set.

  • urg—Urgent pointer bit set.

Step 6

{deny|permit} udp

Example:

{deny | permit} udp {source-ipv6-prefix/prefix-length | any | hostsource-ipv6-address}
[operator [port-number]]{destination-ipv6-prefix/prefix-length | any | hostdestination-ipv6-address}
[operator [port-number]][dscp value] [log][log-input] 
[neq {port |protocol}] [range {port |protocol}] [routing][sequence value][time-range name]

(Optional) Define a UDP access list and the access conditions.

Enter udp for the User Datagram Protocol. The UDP parameters are the same as those described for TCP, except that the operator [port]] port number or name must be a UDP port number or name, and the established parameter is not valid for UDP.

Step 7

{deny|permit} icmp

Example:

{deny | permit} icmp {source-ipv6-prefix/prefix-length | any | hostsource-ipv6-address}
[operator [port-number]] {destination-ipv6-prefix/prefix-length | any | hostdestination-ipv6-address}
[operator [port-number]][icmp-type [icmp-code] |icmp-message] [dscpvalue] [log] [log-input]
[routing] [sequence value][time-range name]

(Optional) Define an ICMP access list and the access conditions.

Enter icmp for Internet Control Message Protocol. The ICMP parameters are the same as those described for most IP protocols in Step 3a, with the addition of the ICMP message type and code parameters. These optional keywords have these meanings:

  • icmp-type—Enter to filter by ICMP message type, a number from 0 to 255.

  • icmp-code—Enter to filter ICMP packets that are filtered by the ICMP message code type, a number from 0 to 255.

  • icmp-message—Enter to filter ICMP packets by the ICMP message type name or the ICMP message type and code name. To see a list of ICMP message type names and code names, use the ? key or see command reference for this release.

Step 8

end

Example:

Device(config)# end

Returns to privileged EXEC mode. Alternatively, you can also press Ctrl-Z to exit global configuration mode.

Step 9

show ipv6 access-list

Example:

show ipv6 access-list

Verify the access list configuration.

Step 10

copy running-config startup-config

Example:

copy running-config startup-config

(Optional) Save your entries in the configuration file.

Applying an IPv6 to an Interface

This section describes how to apply IPv6 ACLs to network interfaces. You can apply an IPv6 ACL to outbound or inbound traffic on layer 2 and Layer 3 interfaces. You can apply IPv6 ACLs only to inbound management traffic on Layer 3 interfaces.

To control access to an interface, perform this procedure:

Procedure

  Command or Action Purpose
Step 1

enable

Example:


Switch> enable

Enables privileged EXEC mode.

Enter your password if prompted.

Step 2

configure terminal

Example:


Switch# configure terminal

Enters global configuration mode.

Step 3

interface interface_id

Example:

Switch# interface interface-id

Identifies a Layer 2 interface (for port ACLs) or Layer 3 Switch Virtual interface (for router ACLs) on which to apply an access list, and enters interface configuration mode.

Step 4

no switchport

Example:

Switch# no switchport

Changes the interface from Layer 2 mode (the default) to Layer 3 mode (only if applying a router ACL).

Step 5

ipv6 address ipv6_address

Example:

Switch# ipv6 address ipv6-address

Configures an IPv6 address on a Layer 3 interface (for router ACLs).

Note 
This command is not required on Layer 2 interfaces or if the interface has already been configured with an explicit IPv6 address.
Step 6

ipv6 traffic-filter acl_name

Example:

Switch# ipv6 traffic-filter access-list-name {in | out}

Applies the access list to incoming or outgoing traffic on the interface.

Step 7

end

Example:

Device(config)# end

Returns to privileged EXEC mode. Alternatively, you can also press Ctrl-Z to exit global configuration mode.

Step 8

show running-config interface tenGigabitEthernet 1/0/3

Example:

Switch# show running-config interface tenGigabitEthernet 1/0/3
..........................
..........................
Building configuration ............
..........................
Current configuration : 98 bytes
!
interface TenGigabitEthernet1/0/3
 switchport mode trunk
 ipv6 traffic-filter MyFilter out
end

Shows the configuration summary.

Step 9

copy running-config startup-config

Example:

copy running-config startup-config

(Optional) Saves your entries in the configuration file.

Displaying IPv6 ACLs

To displayIPv6 ACLs, perform this procedure:

Procedure

  Command or Action Purpose
Step 1

enable

Example:


Switch> enable

Enables privileged EXEC mode.

Enter your password if prompted.

Step 2

configure terminal

Example:


Switch# configure terminal

Enters global configuration mode.

Step 3

show access-list

Example:

Switch# show access-lists

Displays all access lists configured on the switch
Step 4

show ipv6 access-list acl_name

Example:

Switch# show ipv6 access-list [access-list-name]

Displays all configured IPv6 access list or the access list specified by name.

Configuration Examples for IPv6 ACL

Example: Creating IPv6 ACL

This example configures the IPv6 access list named CISCO. The first deny entry in the list denies all packets that have a destination TCP port number greater than 5000. The second deny entry denies packets that have a source UDP port number less than 5000. The second deny also logs all matches to the console. The first permit entry in the list permits all ICMP packets. The second permit entry in the list permits all other traffic. The second permit entry is necessary because an implicit deny -all condition is at the end of each IPv6 access list.

Note
Logging is supported only on Layer 3 interfaces. 
Switch(config)# ipv6 access-list CISCO
Switch(config-ipv6-acl)# deny tcp any any gt 5000
Switch (config-ipv6-acl)# deny ::/0 lt 5000 ::/0 log
Switch(config-ipv6-acl)# permit icmp any any
Switch(config-ipv6-acl)# permit any any

Example: Applying IPv6 ACLs

This example shows how to apply the access list Cisco to outbound traffic on a Layer 3 interface. 


Switch(config-if)# no switchport
Switch(config-if)# ipv6 address 2001::/64 eui-64
Switch(config-if)# ipv6 traffic-filter CISCO out

Example: Displaying IPv6 ACLs

This is an example of the output from the show access-lists privileged EXEC command. The output shows all access lists that are configured on the switch or switch stack.
Switch #show access-lists
Extended IP access list hello
10 permit ip any any
IPv6 access list ipv6
permit ipv6 any any sequence 10
This is an example of the output from the show ipv6 access-lists privileged EXEC command. The output shows only IPv6 access lists configured on the switch or switch stack.
Switch# show ipv6 access-list
IPv6 access list inbound
permit tcp any any eq bgp (8 matches) sequence 10
permit tcp any any eq telnet (15 matches) sequence 20
permit udp any any sequence 30

IPv6 access list outbound
deny udp any any sequence 10
deny tcp any any eq telnet sequence 20

Was this Document Helpful?

FeedbackFeedback

Contact Cisco