The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
Enable the Link Layer Discovery Protocol (LLDP) for devices that require longer wakeup times before they are able to accept data on their receive paths. Doing so enables the device to negotiate for extended system wakeup times from the transmitting link partner.
Changing the Energy Efficient Ethernet (EEE) configuration resets the interface because the device has to restart Layer 1 autonegotiation.
EEE is an IEEE 802.3az standard that is designed to reduce power consumption in Ethernet networks during idle periods.
EEE is enabled by default.
You can enable or disable EEE on an interface that is connected to an EEE-capable link partner. Starting in the Privileged EXEC mode, complete the following steps to enable EEE:
| Command or Action | Purpose | |
|---|---|---|
| Step 1 |
configure terminal Example: |
Enters global configuration mode. |
| Step 2 |
interface interface-id Example: |
Specifies the interface to be configured, and enter interface configuration mode. |
| Step 3 |
power efficient-ethernet auto Example: |
Enables EEE on the specified interface. When EEE is enabled, the device advertises and autonegotiates EEE to its link partner. Enter the no form of the command to disable EEE. |
| Step 4 |
end Example: |
Returns to privileged EXEC mode. |
| Step 5 |
copy running-config startup-config Example: |
(Optional) Saves your entries in the configuration file. |
|
Command |
Purpose |
|---|---|
|
show eee capabilities interface interface-id |
Displays EEE capabilities for the specified interface. |
|
show eee status interface interface-id |
Displays EEE status information for the specified interface. |
The following are sample outputs of the show eee commands:
Device# show eee capabilities interface gigabitethernet 1/0/1
Gi0/1
EEE(efficient-ethernet): yes (100-Tx and 1000T auto)
Link Partner : yes (100-Tx and 1000T auto)
ASIC/Interface : EEE Capable/EEE EnabledDevice# show eee status interface gigabitethernet 1/0/1
Gi0/1 is up
EEE(efficient-ethernet): Operational
Rx LPI Status : Low Power
Tx LPI Status : Low Power
Wake Error Count : 0
ASIC EEE STATUS
Rx LPI Status : Receiving LPI
Tx LPI Status : Transmitting LPI
Link Fault Status : Link Up
Sync Status : Code group synchronization with data stream intactThe following example shows how to disable EEE on an interface:
Device# configure terminal
Device(config)# interface gigabitethernet 1/0/1
Device(config-if)# no power efficient-ethernet auto
The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.
Use the Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.|
Feature Name |
Release |
Feature Information |
|---|---|---|
|
Energy Efficient Ethernet (EEE) |
Cisco IOS Release 15.2(7)E1 |
This feature was introduced Energy Efficient Ethernet (EEE) is an IEEE 802.3az standard that is designed to reduce power consumption in Ethernet networks during idle periods. |
Feedback