Cisco Nexus 7000 Series NX-OS Unicast Routing Command Reference

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Book Contents

Find Matches in This Book

Available Languages

Download Options

Book Title

Cisco Nexus 7000 Series NX-OS Unicast Routing Command Reference

Chapter Title

Show Commands

PDF - Complete Book (7.67 MB) PDF - This Chapter (0.99 MB)
View with Adobe Reader on a variety of devices

Results

Updated:: January 17, 2019

Chapter: Show Commands

show bgp
show bgp community
show bgp community-list
show bgp extcommunity
show bgp extcommunity-list
show bgp ipv4 unicast labels
show bgp neighbors
show bgp sessions
show bgp vpnv4 unicast
show bgp vpnv6 unicast
show event manager events action-log policy
show event manager policy-state
show fhrp
show forwarding
show forwarding distribution
show forwarding inconsistency
show glbp
show glbp capability
show hardware forwarding dynamic-allocation status
show hardware forwarding ip verify
show hardware proxy layer-3 counters
show hardware proxy layer-3 detail
show hsrp
show hsrp bfd-sessions
show hsrp delay
show hsrp mgo
show hsrp summary
show ip adjacency
show ip adjacency summary
show ip adjacency throttle statistics
show ip arp
show ip arp summary
show ip as-path-access-list
show ip bgp
show ip bgp community-list
show ip bgp dampening
show ip bgp extcommunity
show ip bgp extcommunity-list
show ip bgp filter-list
show ip bgp flap-statistics
show ip bgp history-paths
show ip bgp neighbors
show ip bgp nexthop
show ip bgp nexthop-database
show ip bgp peer-policy
show ip bgp peer-session
show ip bgp peer-template
show ip bgp prefix-list
show ip client
show ip community-list
show ip eigrp
show ip eigrp accounting
show ip eigrp interfaces
show ip eigrp neighbors
show ip eigrp policy statistics
show ip eigrp route-map statistics
show ip eigrp topology
show ip eigrp traffic
show ip fib
show ip fib distribution
show ip interface
show ip load-sharing
show ip mbgp
show ip mbgp community
show ip mbgp community-list
show ip mbgp dampening
show ip mbgp extcommunity
show ip mbgp extcommunity-list
show ip mbgp filter-list
show ip mbgp flap-statistics
show ip mbgp history-paths
show ip mbgp neighbors
show ip mbgp nexthop
show ip mbgp nexthop-database
show ip mbgp prefix-list
show ip ospf
show ip ospf border-routers
show ip ospf database
show ip ospf interface
show ip ospf lsa-content-changed-list
show ip ospf memory
show ip ospf neighbors
show ip ospf policy statistics area
show ip ospf policy statistics redistribute
show ip ospf request-list
show ip ospf retransmission-list
show ip ospf routes
show ip ospf statistics
show ip ospf summary-address
show ip ospf traffic
show ip ospf virtual-links
show ip policy
show ip prefix-list
show ip process
show ip rip
show ip rip interface
show ip rip neighbor
show ip rip policy statistics
show ip rip route
show ip rip statistics
show ip route
show ip static-route
show ip static-route track-table
show ip traffic
show ip wccp
show ipv6 adjacency
show ipv6 bgp
show ipv6 bgp community
show ipv6 bgp community-list
show ipv6 bgp dampening
show ipv6 bgp extcommunity-list
show ipv6 bgp filter-list
show ipv6 bgp flap-statistics
show ipv6 bgp history-paths
show ipv6 bgp neighbors
show ipv6 bgp nexthop
show ipv6 bgp nexthop-database
show ipv6 bgp prefix-list
show ipv6 client
show ipv6 eigrp
show ipv6 eigrp accounting
show ipv6 eigrp interfaces
show ipv6 eigrp neighbors
show ipv6 eigrp route-map statistics
show ipv6 eigrp topology
show ipv6 eigrp traffic
show ipv6 fragments
show ipv6 icmp interface
show ipv6 interface
show ipv6 mbgp
show ipv6 mbgp community
show ipv6 mbgp community-list
show ipv6 mbgp neighbors
show ipv6 nd interface
show ipv6 neighbor
show ipv6 policy
show ipv6 prefix-list
show ipv6 process
show ipv6 route
show ipv6 routers
show ipv6 static-route
show ipv6 traffic
show isis
show isis adjacency
show isis database
show isis hostname
show isis interface
show isis ip route-map statistics redistribute
show isis mesh-group
show isis protocol
show isis redistribute route
show isis route
show isis route-map statistics distribute
show isis rrm
show isis spf-log
show isis srm
show isis ssn
show isis statistics
show isis summary-address
show isis traffic
show local policy
show mac-list
show ospfv3
show ospfv3 border-routers
show ospfv3 database
show ospfv3 interface
show ospfv3 memory
show ospfv3 neighbors
show ospfv3 policy statistics area
show ospfv3 policy statistics redistribute
show ospfv3 request-list
show ospfv3 retransmission-list
show ospfv3 routes
show ospfv3 statistics
show ospfv3 summary-address
show ospfv3 traffic
show ospfv3 virtual-links
show routing
show routing ipv6 memory estimate routes
show routing memory estimate
show routing-context
show routing hash
show running-config wccp
show sockets client
show sockets connection
show sockets statistics
show track
show version internal build-identifier
show vrrp
show vrrs client
show vrrs pathway
show vrrs server
show vrrs tag

Show Commands

This chapter describes the Cisco NX-OS unicast routing show commands.

show bgp

To display Border Gateway Protocol (BGP) routes, use the show bgp command.

show bgp {{ ipv4 | ipv6 } { unicast | multicast } | all} [ addr | prefix [ longer-prefixes ]] [ vrf vrf-name ]

Syntax Description

ipv4	Displays BGP information for the IPv4 address family.
ipv6	Displays BGP information for the IPv4 address family.
unicast	Displays BGP information for the unicast address family.
multicast	Displays BGP information for the multicast address family.
all	Displays BGP information for all address families.
addr	(Optional) Network from the selected address family. The format is A.B.C.D for IPv4 and A:B::C:D for IPv6.
prefix	Optional) Prefix from the selected address family. The format is A.B.C.D/length for IPv4 and A:B::C:D/length for IPv6.
longer-prefixes	(Optional) Displays the prefix and any more specific routes.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
6.1(1)	Changed the command output.(existing command will show the configured weight value).
4.0(1)	This command was introduced.
4.2(1)	Added support for IPv6 addresses and prefixes.

Usage Guidelines

Use the show bgp command to display information about BGP.This command does not require a license.

Examples

This example shows how to display an entry in the BGP table:

switch(config-router)# show bgp ipv6 unicast

BGP routing table information for VRF default, address family IPv4 Unicast

BGP table version is 10, local router ID is 3.3.3.3

Status: s-suppressed, x-deleted, S-stale, d-dampened, h-history, *-valid, >-best

Path type: i-internal, e-external, c-confed, l-local, a-aggregate, r-redist

Origin codes: i - IGP, e - EGP, ? - incomplete, | - multipath

Network Next Hop Metric LocPrf Weight Path

* i200.0.1.100/32 201.0.25.1 100 100 6553601 i

*>e 201.0.13.1 0 6553601 i

* i200.0.2.100/32 201.0.25.1 100 100 6553601 i

*>e 201.0.13.1 0 6553601 i

*>l200.0.3.100/32 0.0.0.0 100 32768 i

Related Commands

Command	Description
clear bgp	Clears entries in the BGP table.

show bgp community

To display Border Gateway Protocol (BGP) routes that match a community, use the show bgp community command.

show bgp {{ ipv4 | ipv6 } { unicast | multicast } | all } community [ as-number ] [ internet] [ no-advertise ] [ no-export ] [ no-export-subconfed ] [ exact-match ]} [ vrf vrf-name ]

Syntax Description

ipv4	Displays BGP information for the IPv4 address family.
ipv6	Displays BGP information for the IPv4 address family.
unicast	Displays BGP information for the unicast address family.
multicast	Displays BGP information for the multicast address family.
all	Displays BGP information for all address families.
as-number	(Optional) AS number. The AS number can be a 16-bit integer or a 32-bit integer in the form of <higher 16-bit decimal number>.<lower 16-bit decimal number>.
internet	(Optional) Displays the internet community.
no-advertise	(Optional) Displays the no-advertise community.
no-export	(Optional) Displays the no-export community.
no-export-subconfed	(Optional) Displays the no-export-subconfed community.
exact-match	(Optional) Displays an exact match of the community.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display routes that match a community:

switch(config)# show bgp ip unicast community

Related Commands

Command	Description
ip community-list	Creates a community list.

show bgp community-list

To display Border Gateway Protocol (BGP) routes that match a community list, use the show bgp community-list command.

show bgp {{ ipv4 | ipv6 } { unicast | multicast } | all } community-list commlist-name [ exact-match ] [ vrf vrf-name ]

Syntax Description

ipv4	Displays BGP information for the IPv4 address family.
ipv6	Displays BGP information for the IPv4 address family.
unicast	Displays BGP information for the unicast address family.
multicast	Displays BGP information for the multicast address family.
all	Displays BGP information for all address families.
commlist-name	Name of a community-list. The commlist-name can be any case-sensitive, alphanumeric string up to 63 characters.
exact-match	(Optional) Displays an exact match of the communities.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display routes that match a community list:

switch(config)# show bgp ip unicast community-list test1

Related Commands

Command	Description
ip community-list	Creates a community list.

show bgp extcommunity

To display Border Gateway Protocol (BGP) routes that match an extended community, use the show bgp extcommunity command.

show bgp {{ ipv4 | ipv6 } { unicast | multicast } | all } extcommunity generic { non-transitive | transitive } [ as4-number ] [ exact-match ] [ vrf vrf-name ]

Syntax Description

ipv4	Displays BGP information for the IPv4 address family.
ipv6	Displays BGP information for the IPv4 address family.
unicast	Displays BGP information for the unicast address family.
multicast	Displays BGP information for the multicast address family.
all	Displays BGP information for all address families.
generic	Displays the routes that match the generic specified extended communities.
non-transitive	Displays the routes that match the non-transitive extended communities.
transitive	Displays the routes that match the transitive extended communities.
as4-number	AS number. The as4-number is a 32-bit integer in the form of a plaintext integer or <higher 16-bit decimal number>.<lower 16-bit decimal number>.
exact-match	(Optional) Displays an exact match of the extended community.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.2(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows hoe to display routes that match an extended community:

switch(config)# show bgp ip unicast extcommunity generic transitive 1.3:30

Related Commands

Command	Description
ip extcommunity-list	Creates an extended community list.

show bgp extcommunity-list

To display Border Gateway Protocol (BGP) routes that match an extended community list, use the show bgp extcommunity-list command.

show bgp {{ ipv4 | ipv6 } { unicast | multicast } | all } extcommunity-list commlist-name [ exact-match ] [ vrf vrf-name ]

Syntax Description

ipv4	Displays BGP information for the IPv4 address family.
ipv6	Displays BGP information for the IPv4 address family.
unicast	Displays BGP information for the unicast address family.
multicast	Displays BGP information for the multicast address family.
all	Displays BGP information for all address families.
commlist-name	Name of an extended community-list. The commlist-name can be any case-sensitive, alphanumeric string up to 63 characters.
exact-match	(Optional) Displays an exact match of the extended communities.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.2(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display routes that match a community list:

switch(config)# show bgp ipv6 unicast extcommunity-list test1

Related Commands

Command	Description
ip extcommunity-list	Creates an extended community list.

show bgp ipv4 unicast labels

To display Border Gateway Protocol (BGP) labels for prefixes, use the show bgp ipv4 unicast labels command.

show bgp ipv4 unicast labels vrf {vrf-name | all | default | management}

Syntax Description

vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 32 characters.
all	Specifies all VRF.
default	Specifies default VRF name.
management	Specifies management VRF name.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
15.2(2)SNG	This command was implemented on the Cisco ASR 901 Series Aggregation Services Router.
4.1(2)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display BGP labels for prefixes:

switch(config)# show bgp ipv4 unicast labels

Related Commands

Command	Description
show ip bgp neighbors	Displays the IPv4 BGP information.

show bgp neighbors

To display Border Gateway Protocol (BGP) neighbors, use the show bgp neighbors command.

show bgp { ip | ipv6 } { unicast | multicast } neighbors [ addr [ advertised-routes | flap-statistics | paths | received-routes | routes [ advertised | dampened | received ]] | prefix ] [ vrf { all | vrf-name }]

Syntax Description

ip	Displays the IPv4 neighbor information.
ipv6	Displays the IPv6 neighbor information.
unicast	Displays the unicast neighbor information.
multicast	Displays the multicast neighbor information.
addr	IPv4 address. The format is x.x.x.x
advertised-routes	(Optional) Displays all the routes advertised to this neighbor.
flap-statistics	(Optional) Displays flap statistics for the routes received from this neighbor.
paths	(Optional) Displays AS paths learned from this neighbor.
received-routes	(Optional) Displays all the routes received from this neighbor.
routes	(Optional) Displays the routes received or advertised to or from this neighbor.
advertised	(Optional) Displays all the routes advertised for this neighbor.
dampened	(Optional) Displays all dampened routes received from this neighbor.
received	(Optional) Displays all the routes received from this neighbor.
prefix	(Optional) IPv6 prefix. The format is x.x.x.x/length.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.
all	Specifies all VRF.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.
4.1(2)	Added the paths keyword.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the BGP neighbors:

switch(config)# show bgp ip unicast neighbors

Related Commands

Command	Description
show ip bgp neighbors	Displays the IPv4 BGP information.
show ipv6 bgp neighbors	Displays the IPv6 BGP information.

show bgp sessions

To display Border Gateway Protocol (BGP) sessions, use the show bgp sessions command.

show bgp sessions [ vrf vrf-name ]

Syntax Description

vrf vrf-name

(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display BGP sessions:

switch# show bgp sessions

Total peers 0, established peers 0

ASN 33.33

VRF default, local ASN 33.33

peers 0, established peers 0, local router-id 192.168.1.222

State: I-Idle, A-Active, O-Open, E-Established, C-Closing, S-Shutdown

Flaps LastUpDn|LastRead|LastWrit St Port(L/R) Notif(S/R)

Related Commands

Command	Description
clear bgp	Clears BGP sessions.

show bgp vpnv4 unicast

To display VPNv4 routes from BGP table, use the show bgp vpnv4 unicast command.

show bgp vpnv4 unicast [ ip-prefix/length [ longer-prefixes ] | network-address [ mask ] [ longer-prefixes ]] [ community community ] [ community-list community-list ] [ dampening ] [ extcommunity extcommunity ] [ extcommunity-list extcommunity-list ] [ filter-list filter-list ] [ flap-statistics ] [ neighbors neighbor ] [ nexthop [ nexthop ]] [ regexp regexp ] [ imported ] [ exported ] [ summary ] [ labels ] { vrf { vrf-name | all } | rd route-distinguisher }

Syntax Description

ip-prefix/length	(Optional) IP prefix address in the dotted decimal format and the length of the mask from 0 to 32.
longer-prefixes	(Optional) Displays the entry, if any, that exactly matches the specified prefix parameter and all entries that match the prefix in a “longest-match” sense. That is, prefixes for which the specified prefix is an initial substring.
network-address	(Optional) IP address of a network in the BGP routing table.
mask	(Optional) Mask of the network address, in dotted decimal format.
community community	(Optional) Displays routes that match this community.
community-list community-list	(Optional) Displays routes that match this community list.
dampening	(Optional) Displays dampening information.
extcommunity extcommunity	(Optional) Displays routes that match this extcommunity.
extcommunity-list extcommunity-list	(Optional) Displays routes that match this extcommunity list.
filter-list filter-list	(Optional) Displays routes that match this filter list.
flap-statistics	(Optional) Displays route flap statistics.
neighbors neighbor	(Optional) Displays all configured BGP neighbors.
nexthop nexthop	(Optional) Displays routes that match this nexthop.
regexp regexp	(Optional) Displays routes that match AS path regular expression.
imported	(Optional) Displays imported routes only.
exported	(Optional) Displays exported routes only.
summary	(Optional) Displays summarized information of BGP state.
labels	(Optional) Displays incoming and outgoing BGP labels for each NLRI prefix.
vrf vrf-name	Displays routes for a specific VRF.
all	Displays routes for all VRFs.
rd route-distinguisher	Displays routes matching specified route-distinguisher.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.2(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display VPNv4 routes from BGP table:

switch# show bgp vpnv4 unicast summary

BGP summary information for VRF default, address family VPNv4 Unicast

switch#

Related Commands

Command	Description
show bgp vpnv6 unicast	Displays VPNv6 routes from BGP table.

show bgp vpnv6 unicast

To display VPNv6 routes from BGP table, use the show bgp vpnv6 unicast command.

show bgp vpnv6 unicast [ ipv6-prefix/length [ longer-prefixes ] | network-address [ mask ] [ longer-prefixes ]] [ community community ] [ community-list community-list ] [ dampening ] [ extcommunity extcommunity ] [ extcommunity-list extcommunity-list ] [ filter-list filter-list ] [ flap-statistics ] [ neighbors neighbor ] [ nexthop [ nexthop ]] [ regexp regexp ] [ imported ] [ exported ] [ summary ] [ labels ] { vrf { vrf-name | all } | rd route-distinguisher }

Syntax Description

ipv6-prefix/length	(Optional) IPv6 prefix address.
longer-prefixes	(Optional) Displays the entry, if any, that exactly matches the specified prefix parameter and all entries that match the prefix in a “longest-match” sense. That is, prefixes for which the specified prefix is an initial substring.
network-address	(Optional) IP address of a network in the BGP routing table.
mask	(Optional) Mask of the network address, in dotted decimal format.
community community	(Optional) Displays routes that match this community.
community-list community-list	(Optional) Displays routes that match this community list.
dampening	(Optional) Displays dampening information.
extcommunity extcommunity	(Optional) Displays routes that match this extcommunity.
extcommunity-list extcommunity-list	(Optional) Displays routes that match this extcommunity list.
filter-list filter-list	(Optional) Displays routes that match this filter list.
flap-statistics	(Optional) Displays route flap statistics.
neighbors neighbor	(Optional) Displays all configured BGP neighbors.
nexthop nexthop	(Optional) Displays routes that match this nexthop.
regexp regexp	(Optional) Displays routes that match AS path regular expression.
imported	(Optional) Displays imported routes only.
exported	(Optional) Displays exported routes only.
summary	(Optional) Displays summarized information of BGP state.
labels	(Optional) Displays incoming and outgoing BGP labels for each NLRI prefix.
vrf vrf-name	Displays routes for a specific VRF.
all	Displays routes for all VRFs.
rd route-distinguisher	Displays routes matching specified route-distinguisher.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.2(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display VPNv6 routes from BGP table:

switch# show bgp vpnv6 unicast vrf all

l3dc3-1# show bgp vpnv6 unicast vrf all

BGP routing table information for VRF default, address family VPNv6 Unicast

BGP table version is 4, local router ID is 1.1.1.1

Status: s-suppressed, x-deleted, S-stale, d-dampened, h-history, *-valid, >-best

Path type: i-internal, e-external, c-confed, l-local, a-aggregate, r-redist

Origin codes: i - IGP, e - EGP, ? - incomplete, | - multipath

Network Next Hop Metric LocPrf Weight Path

Route Distinguisher: 1.1.1.1:1 (VRF redist-bgp-l3vpn)

*>i100:1:1::1/128 20:5::2 100 0 i

*>e200:1:1::1/128 20:6::2 0 200 i

switch#

Related Commands

Command	Description
show bgp vpnv4 unicast	Displays VPNv4 routes from BGP table.

show event manager events action-log policy

To display an event action log for the specified Embedded Event Manager (EEM) policy, use the show event manager events action-log policy command.

show event manager events action-log policy applet-name

Syntax Description

applet-name

Applet name. The maximum range is 29 alphanumeric, case-sensitive characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
6.2(2)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display an event action log for the specified EEM policy:

switch# show event manager events action-log policy Route1

switch#

Related Commands

Command	Description
show event manager policy-state	Displays information about the status of the specified event policy.

show event manager policy-state

To display information about the status of the specified event policy, use the show event manager policy-state command.

show event manager policy-state applet-name

Syntax Description

applet-name

Applet name. The maximum range is 29 alphanumeric, case-sensitive characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
6.2(2)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about the status of the specified event policy:

switch# show event manager policy-state applet 1

switch#

Related Commands

Command	Description
show event manager events action-log policy	Displays an event action log for the specified EEM policy.

show fhrp

To display First Hop Redundancy Protocol (FHRP) information, use the show fhrp command.

show fhrp [ interface-type interface-number ] [ verbose ]

Syntax Description

interface-type	Interface type.
interface-number	Interface number.
verbose	(Optional) Specifies verbose.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
6.2(2)	This command was introduced.

Usage Guidelines

Use the verbose keyword to view detailed information.

This command does not require a license.

Examples

This example shows how to display FHRP information:

switch# show fhrp port-channel 101 verbose

Interface L2 IPv4 IPv6 Hardware Ref Cnt

Ethernet6/1 down down down present 3

switch#

Related Commands

Command	Description
vfhrp delay	Specifies the delay period for the initialization of First Hop Redundancy Protocol (FHRP) clients.

show forwarding

To display forwarding information, use the show forwarding command.

show forwarding [ ip | ipv4 | ipv6 ] { adjacency | interfaces | route | trace [ clear ] | table id pss route } [ module slot ] [ vrf vrf-name ]

Syntax Description

ip	(Optional) Displays the IPv4 forwarding information.
ipv4	(Optional) Displays the IPv4 forwarding information.
ipv6	(Optional) Displays the IPv6 forwarding information.
adjacency	Displays the adjacency information.
interfaces	Displays the forwarding information for interfaces on a module.
route	Displays the forwarding information for routes on a module.
trace	Displays the forwarding trace buffer on a module.
clear	(Optional) Clears the forwarding trace buffer on a module.
table id	Displays the forwarding information for a route table. The id range is from 0 to 2147483647.
pss route	Displays route information from persistent storage.
module slot	(Optional) Displays information for the module. The slot range depends on the hardware platform.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.
4.1(2)	Added the trace and clear keywords.
4.2(1)	Added the table pss route keywords.

Usage Guidelines

Use the show forwarding command on the supervisor to view forwarding information on a module. Optionally, you can use the attach module command to attach to a module and use the show forwarding command on the module.

This command does not require a license.

Examples

This example shows how to display forwarding information for module 2:

switch# show forwarding route module 2

IPv4 routes for table default/base

------------------+------------------+---------------------

Prefix | Next-hop | Interface

------------------+------------------+---------------------

0.0.0.0/32 Drop Null0

255.255.255.255/32 Receive sup-eth1

Related Commands

Command	Description
show ip fib	Displays information about the FIB.

show forwarding distribution

To display forwarding distribution information, use the show forwarding distribution command.

show forwarding distribution [ clients | fib-state ]

Syntax Description

clients	(Optional) Displays the forwarding distribution information for unicast clients.
fib-state	(Optional) Displays the forwarding distribution state for unicast Forwarding Information Base (FIB).

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display forwarding information for unicast clients:

switch# show forwarding distribution clients

id pid shmem-start shmem-end shmem-name

-- ----- ----------- --------- ----------

1 3646 0x64f70120 0x64fc0000 u6rib-ufdm

2 3647 0x64b50120 0x64d50000 urib-ufdm

Related Commands

Command	Description
show ip fib distribution	Displays distribution information about the FIB.

show forwarding inconsistency

To display the results of the forwarding inconsistency checker, use the show forwarding inconsistency command.

show forwarding inconsistency [ ip | ipv4 | ipv6 ] [ unicast ] module slot [ vrf vrf-name ]

Syntax Description

ip	(Optional) Displays the IPv4 forwarding inconsistency information.
ipv4	(Optional) Displays the IPv4 forwarding inconsistency information.
ipv6	(Optional) Displays the IPv6 forwarding inconsistency information.
unicast	(Optional) Displays the forwarding inconsistency information for unicast routes
module slot	Displays inconsistency information for the module. The slot range depends on the hardware platform.
vrf vrf-name	(Optional) Displays inconsistency information for the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(3)	This command was introduced.
4.2(1)	Added support for ipv6 keyword.

Usage Guidelines

Use the show forwarding inconsistency command to display the results of the test forwarding inconsistency command.

This command does not require a license.

Examples

This example shows how to display forwarding inconsistency information for module 2:

switch# show forwarding inconsistency module 2

Consistency check : table_id(0x1) slot(2)

No inconsistent adjacencies.

No inconsistent routes.

Related Commands

Command	Description
clear forwarding inconsistency	Clears the forwarding inconsistency checker.
test forwarding inconsistency	Triggers the forwarding inconsistency checker.

show glbp

To display Gateway Load Balancing Protocol (GLBP) information, use the show glbp command.

show glbp [ interface type number ] [ group number ] [ state ] [ brief ] [ vrf vrf-name ]

Syntax Description

interface type number	(Optional) Specifies the interface to display GLBP information.
group number	(Optional) Specifies the GLBP group number. The range is from 0 to 1023.
state	(Optional) State of the GLBP router. The states are as follows: active, disabled, init, listen, or standby.
brief	(Optional) Summarizes each virtual gateway or virtual forwarder with a single line of output.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names. Supported in Cisco NX-OS Release 4.0(2) and later releases.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.
4.0(2)	Added support for vrf keyword.

Usage Guidelines

Use the show glbp command to display information about GLBP groups. The brief keyword displays a single line of information about each virtual gateway or virtual forwarder.

This command does not require a license.

Examples

This example shows how to display GLBP information:

switch# show glbp

Ethernet2/1 - Group 10

State is Active

2 state changes, last state change 23:50:33

Virtual IP address is 192.0.2.10

Hello time 5 sec, hold time 18 sec

Next hello sent in 4.300 secs

Redirect time 600 sec, forwarder time-out 7200 sec

Authentication MD5, key "ThisStringIsTheSecretKey"

Preemption enabled, min delay 60 sec

Active is local

Standby is unknown

Priority 254 (configured)

Weighting 105 (configured 110), thresholds: lower 95, upper 105

Track object 2 state Down decrement 5

Load balancing: host-dependent

Group members:

0016.C76C.85DC (7.199.10.1) local

There is 1 forwarder (1 active)

Forwarder 1

State is Active

1 state change, last state change 23:50:15

MAC address is 0007.b400.0101 (default)

Owner ID is 0005.0050.6c08

Redirection enabled

Preemption enabled, min delay 60 sec

Active is local, weighting 105

This example shows how to display a brief summary of GLBP information:

switch# show glbp brief

Interface Grp Fwd Pri State Address Active router Standby router

Eth2/1 10 - 254 Active 192.0.2.10 local unknown

Eth1/2 10 1 7 Active 0007.b400.0101 local -

This example shows how to specify the GLBP interface and group number:

switch# show glbp interface ethernet2/2 group 1

Ethernet2/2 - Group 1

State is Listen

64 state changes, last state change 00:00:54

Virtual IP address is 10.1.0.7

Hello time 50 msec, hold time 200 msec

Next hello sent in 0.030 secs

Redirect time 600 sec, forwarder time-out 14400 sec

Authentication text "authword"

Preemption enabled, min delay 0 sec

Active is 10.1.0.2, priority 105 (expires in 0.184 sec)

Standby is 10.1.0.3, priority 100 (expires in 0.176 sec)

Priority 96 (configured)

Weighting 100 (configured 100), thresholds: lower 95, upper 100

Track object 1 state Up decrement 10

Load balancing: round-robin

Group members:

0004.4d83.4801 (10.0.0.0)

0010.7b5a.fa41 (10.0.0.1)

00d0.bbd3.bc21 (10.0.0.2) local

Table 17-1 describes the significant fields shown in the displays.

Table 17-1 show glbp Field Descriptions
Field	Description
Ethernet2/1 - Group	Interface type and number and GLBP group number for the interface.
State is	State of the virtual gateway. For a virtual gateway, the state can be one of the following: Active—The gateway is the active virtual gateway (AVG) and is responsible for responding to Address Resolution Protocol (ARP) requests for the virtual IP address. Disabled—The virtual IP address has not been configured or learned yet, but another GLBP configuration exists. Initial—The virtual IP address has been configured or learned, but the virtual gateway configuration is not complete. An interface must be up and configured to route IP, and an interface IP address must be configured. Listen—The virtual gateway is receiving hello packets and is ready to change to the Speak state if the active or standby virtual gateway becomes unavailable. Speak—The virtual gateway is attempting to become the active or standby virtual gateway. Standby—The gateway is next in line to be the AVG. For a virtual forwarder, the state can be one of the following: Active—The gateway is the active virtual forwarder (AVF) and is responsible for forwarding packets sent to the virtual forwarder MAC address. Disabled—The virtual MAC address has not been assigned or learned. This state is transitory because a virtual forwarder that changes to a disabled state is deleted. Initial—The virtual MAC address is known, but the virtual forwarder configuration is not complete. An interface must be up and configured to route IP, an interface IP address must be configured, and the virtual IP address must be known. Listen—The virtual forwarder is receiving hello packets and is ready to change to the Active state if the AVF becomes unavailable.
State is
Virtual IP address is	Virtual IP address of the GLBP group. All secondary virtual IP addresses are listed on separate lines. If a virtual IP address is a duplicate of an address configured for another device, it will be marked as a duplicate. A duplicate address indicates that the router has failed to defend its ARP cache entry.
Hello time, hold time	Time between hello packets, in seconds or milliseconds, that indicates the hello time. The hold time is the time (in seconds or milliseconds) before other routers declare the active router to be down. All routers in a GLBP group use the hello-time and hold-time values of the current AVG. If the locally configured values are different, the configured values appear in parentheses after the hello-time and hold-time values.
Redirect time, forwarder time-out	Redirect and timeout times for an AVF transition to a standby virtual forwarder. The redirect time is the time during which the AVG for a GLBP group continues to redirect clients to a secondary AVF. The timeout is the time (in seconds) before the secondary virtual forwarder becomes unavailable.
Preemption	Whether GLBP gateway preemption is enabled. If enabled, the minimum delay is the time, in seconds, for which a higher-priority nonactive router will wait before preempting the lower-priority active router. This field is also displayed under the forwarder section where it indicates GLBP forwarder preemption.
Active is	Active state of the virtual gateway. The value can be local, unknown, or an IP address. The address (and the expiration date of the address) is the address of the current AVG. This field is also displayed under the forwarder section where it indicates the address of the current AVF.
Standby is	Standby state of the virtual gateway. The value can be local, unknown, or an IP address. The address (and the expiration date of the address) is the address of the standby gateway (the gateway that is next in line to be the AVG).
Weighting	Initial weighting value with lower and upper threshold values.
Track object	List of objects that are being tracked and their corresponding states.
Load balancing	Load-balancing method configured for the GLBP group.
Group members	List of gateways that are members of this group.
Forwarder	List of forwarders in this group.

Table 17-2 describes the fields for the show glbp brief command output.

Table 17-2 show glbp brief Field Descriptions
Field	Description
Interface	Interface type and number. GLBP group number for the interface.
Grp	GLBP group number for the interface.
Fwd	Number of forwarders in the GLBP group.
Pri	Configured priority for this gateway.
State is	State of the virtual gateway. For a virtual gateway, the state can be one of the following: Active—The gateway is the active virtual gateway (AVG) and is responsible for responding to Address Resolution Protocol (ARP) requests for the virtual IP address. Disabled—The virtual IP address has not been configured or learned yet, but another GLBP configuration exists. Initial—The virtual IP address has been configured or learned, but the virtual gateway configuration is not complete. An interface must be up and configured to route IP, and an interface IP address must be configured. Listen—The virtual gateway is receiving hello packets and is ready to change to the Speak state if the active or standby virtual gateway becomes unavailable. Speak—The virtual gateway is attempting to become the active or standby virtual gateway. Standby—The gateway is next in line to be the AVG. For a virtual forwarder, the state can be one of the following: Active—The gateway is the active virtual forwarder (AVF) and is responsible for forwarding packets sent to the virtual forwarder MAC address. Disabled—The virtual MAC address has not been assigned or learned. This state is transitory because a virtual forwarder that changes to a disabled state is deleted. Initial—The virtual MAC address is known, but the virtual forwarder configuration is not complete. An interface must be up and configured to route IP, an interface IP address must be configured, and the virtual IP address must be known. Listen—The virtual forwarder is receiving hello packets and is ready to change to the Active state if the AVF becomes unavailable.
State is
Address	Virtual IP address of the GLBP group. All secondary virtual IP addresses are listed on separate lines. If a virtual IP address is a duplicate of an address configured for another device, it will be marked as a duplicate. A duplicate address indicates that the router has failed to defend its ARP cache entry.
Active router	IP address of the AVG.
Standby router	IP address of the standby virtual gateway.

Related Commands

Command	Description
glbp ip	Enables GLBP.
glbp timers	Configures the time between hello messages and the time before other routers declare the active GLBP router to be down.
glbp weighting track	Specifies an object to be tracked that affects the weighting of a GLBP gateway.

show glbp capability

To display which interfaces support Gateway Load Balancing Protocol (GLBP), use the show glbp capability command.

show glbp [ interface type number ] [ port-channel number ] [ vlan number ]

Syntax Description

interface type number	(Optional) Specifies the interface for which output is displayed.
port-channel number	(Optional) Specifies the port channel for which output is displayed.
vlan number	(Optional) VLAN for which output is displayed.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show glbp capability command to display which interfaces support GLBP.

This command does not require a license.

Examples

This example shows how to display the interfaces that support GLBP :

switch# show glbp capability

Nexus 7010 (10 Slot) Chassis * means interface may support GLBP

Interface Type | Potential Max Groups

Eth1/1 2 Gigabit Ethernet * 1024

Eth1/2 2 Gigabit Ethernet * 1024

Eth2/1 2 Gigabit Ethernet * 1024

Eth2/2 2 Gigabit Ethernet * 1024

Eth2/3 2 Gigabit Ethernet * 1024

Eth2/4 2 Gigabit Ethernet * 1024

Eth2/5 2 Gigabit Ethernet * 1024

Eth2/6 2 Gigabit Ethernet * 1024

Eth2/7 2 Gigabit Ethernet * 1024

Eth2/8 2 Gigabit Ethernet * 1024

mgmt0 5 Management Sup Port 0

Eth Inband Port 21 Inband Port 0

Table 17-3 describes the significant fields shown in the output.

Table 17-3 show glbp capability Field Descriptions
Field	Description
Interface	Interface name.
Type	Interface type.
GLBP support (represented by the \| character)	* indicates the interface may support GLBP.
Potential Max Groups	Maximum number of groups supported by this interface.

Related Commands

Command	Description
glbp ip	Enables GLBP.
glbp timers	Configures the time between hello messages and the time before other routers declare the active GLBP router to be down.
glbp weighting track	Specifies an object to be tracked that affects the weighting of a GLBP gateway.

show hardware forwarding dynamic-allocation status

To display information about the ternary content addressable memory (TCAM) allocation in the Forwarding Information Base (FIB), use the show hardware forwarding dynamic-allocation status command.

show hardware forwarding dynamic-allocation status

Syntax Description

This command has no keywords or arguments.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.2(1)	This command was introduced.
5.0(x)	This command was deprecated.

Usage Guidelines

As of Cisco NX-OS Release 5.0(x), dynamic TCAM allocation is enabled by default and cannot be disabled.

Use the show hardware forwarding dynamic-allocation status command to display the TCAM allocation for one or more modules.

This command does not require a license.

Examples

This example shows how to display the TCAM allocation:

switch(config)# show hardware forwarding dynamic-allocation status

slot 7

=======

Num 288 bit blocks : 1 (Same as default setting)

Num 144 bit blocks : 8 (Same as default setting)

Num 72 bit blocks : 7 (Same as default setting)

slot 12

=======

Num 288 bit blocks : 1 (Same as default setting)

Num 144 bit blocks : 7 (Different from default setting)

Num 72 bit blocks : 9 (Different from default setting)

Related Commands

Command	Description
hardware forwarding dynamic-allocation	Configures dynamic TCAM allocation for each module.

show hardware forwarding ip verify

To display information about IP packet verification, use the show hardware forwarding ip verify command.

show hardware forwarding ip verify

Syntax Description

This command has no keywords or arguments.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to configure IP packet verification settings:

switch# show hardware forwarding ip verify

IPv4 and v6 IDS Checks Status Packets Failed

-----------------------------+---------+------------------

address source broadcast Enabled 0

address source multicast Enabled 0

address destination zero Enabled 0

address identical Enabled 0

address source reserved Enabled 0

address class-e Disabled 0

checksum Enabled 0

protocol Enabled 0

fragment Enabled 0

length minimum Enabled 0

length consistent Enabled 0

length maximum max-frag Enabled 0

length maximum udp Disabled 0

length maximum max-tcp Enabled 0

tcp flags Disabled 0

tcp tiny-frag Enabled 0

version Enabled 0

-----------------------------+---------+------------------

IPv6 IDS Checks Status Packets Failed

-----------------------------+---------+------------------

length consistent Enabled 0

length maximum max-frag Enabled 0

length maximum udp Disabled 0

length maximum max-tcp Enabled 0

tcp tiny-frag Enabled 0

version Enabled 0

Related Commands

Command	Description
platform ip verify address	Configures IPv4 and IPv6 packet verification checks based on addresses.
platform ip verify length	Configures IPv4 packet verification checks based on length.
platform ipv6 verify	Configures IPv6 packet verification.

show hardware proxy layer-3 counters

To displays proxy layer 3 counter information, use the show hardware proxy layer-3 counters command.

show hardware proxy layer-3 counters {brief | detail}

Syntax Description

brief	Displays brief information for the proxy.
detail	Displays detailed information for the proxy.

Defaults

None

Command Modes

EXEC

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
5.1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display brief proxy layer 3 counters information:

switch# show hardware proxy layer-3 counters brief

Summary:

--------

Proxy packets sent by all F-series module:

-----------------------------------------------------------------------

Router Interfaces Tx-Pkts Tx-Rate (pkts/sec approx.

-----------------------------------------------------------------------

Eth6/1 0 0

Eth6/2 0 0

Eth6/3 0 0

Eth6/4 0 0

Eth6/5 0 0

Eth6/6 0 0

Eth6/7 0 0

Eth6/8 0 0

Eth7/1-12 0 0

Eth7/13-24 0 0

Eth7/25-36 0 0

Eth7/37-48 0 0

Eth8/1-12 0 0

Eth8/13-24 0 0

Eth8/25-36 0 0

Eth8/37-48 0 0

switch#

This example shows how to display detailed proxy layer 3 counters information:

switch# show hardware proxy layer-3 counters detail

Proxy packets sent by F-series module: 5

-----------------------------------------------------------------------

Router Interfaces Tx-Pkts Tx-Rate (pkts/sec approx.

-----------------------------------------------------------------------

Eth6/1 0 0

Eth6/2 0 0

Eth6/3 0 0

Eth6/4 0 0

Eth6/5 0 0

Eth6/6 0 0

Eth6/7 0 0

Eth6/8 0 0

Eth7/1-12 0 0

Eth7/13-24 0 0

Eth7/25-36 0 0

Eth7/37-48 0 0

Eth8/1-12 0 0

Eth8/13-24 0 0

Eth8/25-36 0 0

Eth8/37-48 0 0

==========================================================

Total 0 0

==========================================================

--More--

Related Commands

Command	Description
show hardware proxy layer-3 detail	Displays detail information on the proxy layer 3 functionality.

show hardware proxy layer-3 detail

To displays detail proxy layer 3 forwarding information, use the show hardware proxy layer-3 detail command.

show hardware proxy layer-3 detail

Syntax Description

This command has no arguments or keywords.

Defaults

None

Command Modes

EXEC

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
5.1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display detail proxy layer 3 forwarding information:

switch# show hardware proxy layer-3 detail

Global Information:

F1 Modules: Count: 0 Slot:

M1 Modules: Count: 0 Slot:

Replication Rebalance Mode: Manual

Number of proxy layer-3 forwarders: 0

Number of proxy layer-3 replicators: 0

switch#

Related Commands

Command	Description
show hardware proxy layer-3 detail	Displays detail information on the proxy layer 3 functionality.

show hsrp

To display Hot Standby Router Protocol (HSRP) information for each HSRP group, use the show hsrp command.

show hsrp [ interface type number ] [ group group -number ] [ active | init | listen | standby ] [ all ] [ brief {all}] [ detail ] [ ipv4 | ipv6 ]

Syntax Description

interface type number	(Optional) Specifies the interface type and number for which to display HSRP information.
group group -number	(Optional) Specifies the HSRP group number of the interface to display information about.
active	(Optional) Displays HSRP groups that are in an active state.
init	(Optional) Displays HSRP groups that are in an initialization state.
listen	(Optional) Displays HSRP groups that are in an listen state.
standby	(Optional) Displays HSRP groups that are in an standby state.
all	(Optional) Displays all HSRP groups.
brief	(Optional) Summarizes each virtual gateway or virtual forwarder with a single line of output.
all	(Optional) Displays all the virtual IPs on the group only for the IPV6 HSRP groups.
detail	(Optional) Displays detailed information about HSRP groups.
ipv4	(Optional) Displays only IPv4 HSRP groups.
ipv6	(Optional) Displays only IPv6 HSRP groups.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.
4.1(2)	Added the ipv4 keyword.
4.2(1)	Added the detail keyword.
5.0(2)	Added the ipv6 keyword.
5.1(1)	Added all to the brief keyword.

Usage Guidelines

Use the show hsrp command to display information about HSRP groups. The brief keyword displays a single line of information about each virtual gateway or virtual forwarder.

If you have not configured authentication, the show hsrp command will display the following string:

Authentication text "cisco"

This is the default behavior of HSRP as defined in RFC 2281 :

If no authentication data is configured, the RECOMMENDED default
value is 0x63 0x69 0x73 0x63 0x6F 0x00 0x00 0x00.

This command does not require a license.

Examples

This example shows how to display the default information about HSRP:

switch# show hsrp

Vlan1 - Group 1 (HSRP-V1) (IPv4)

Local state is Active, priority 150 (Cfged 150), may preempt

Forwarding threshold(for vPC), lower: 1 upper: 150

Preemption Delay (Seconds) Reload:300

Hellotime 3 sec, holdtime 10 sec

Next hello sent in 0.793000 sec(s)

Virtual IP address is 10.1.1.3 (Cfged)

Active router is local

Standby router is unknown

Authentication text "cisco"

Virtual mac address is 0000.0c07.ac01 (Default MAC)

17 state changes, last state change 1w0d

IP redundancy name is hsrp-Vlan1-1 (default)

...

Note The authentication text string in the preceding example indicates that authentication has not been configured on the interface.

This example shows how to display a brief summary of HSRP information:

switch# show hsrp brief all

P indicates configured to preempt.

Interface Grp Prio P State Active addr Standby addr Group

addr

Eth1/1 1 100 Active local unknown

fe80::5:73ff:f

ea0:1 (conf auto EUI64)

Eth1/1 1 100 Active local unknown 1::2

Eth1/1 1 100 Active local unknown 1::1

Related Commands

Command	Description
feature hsrp	Enables the HSRP feature.

show hsrp bfd-sessions

To display Hot Standby Router Protocol (HSRP) bfd sessions, use the show hsrp bfd-sessions command.

show hsrp bfd-sessions

Syntax Description

This command has no keywords or arguments

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
5.0(2)	This command was introduced.

Usage Guidelines

Use the show hsrp bfd-sessions command to display information about HSRP BFD sessions.

This command does not require a license.

show hsrp delay

To display Hot Standby Router Protocol (HSRP) group delay information, use the show hsrp delay command.

show hsrp delay [ interface type number ] [ group group -number ] [ all ] [ brief ]

Syntax Description

interface type number	(Optional) Specifies the interface type and number for which to display HSRP information.
group group -number	(Optional) Specifies the HSRP group number of the interface to display information about.
all	(Optional) Specifies all HSRP information.
brief	(Optional) Specifies brief HSRP information.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show hsrp delay command to display delay information about HSRP groups.

This command does not require a license.

Examples

This example shows how to display GLBP delay information:

switch# show hsrp delay

show hsrp mgo

To display the relationships between Hot Standby Redundancy Protocol (HSRP) groups that are in use for multiple group optimization (MGO) and their slave sessions, use the show hsrp mgo command.

show hsrp mgo name name [brief]

Syntax Description

name	Restricts the output to the session with a matching configured name.
name	HRSP group name.
brief	(Optional) Provides a summary of each MGO session with the associated slave sessions

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
6.2(2)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the relationships between HSRP groups that are in use for MGO and their slave sessions:

switch# show hsrp mgo name Master_Group-1

switch#

Related Commands

Command	Description
show hsrp	Displays HSRP information.

show hsrp summary

To display Hot Standby Router Protocol (HSRP) summary information for each HSRP group, use the show hsrp summary command.

show hsrp summary

Syntax Description

This command has no keywords or arguments.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.2(1)	This command was introduced.

Usage Guidelines

Use the show hsrp summary command to display summary information about HSRP groups.

This command does not require a license.

Examples

This example shows how to display a summary of HSRP information:

switch# show hsrp summary

PHSRP Summary:

--------------------------------

Extended-hold (NSF) disabled

Total Groups: 1

Version:: V1-IPV4: 1 V2-IPV4: 0

State:: Active: 0 Standby: 0 Listen: 0

Total HSRP Enabled interfaces: 1

Total Packets:

Tx - Pass: 0 Fail: 0

Rx - Good: 0

Packet for unknown groups: 0

Total MTS: Rx: 142

--------------------------------

Related Commands

Command	Description
feature hsrp	Enables the HSRP feature.

show ip adjacency

To display adjacency information, use the show ip adjacency command.

show ip adjacency [ ip-addr | interface ] [ detail ] [ non-best ] [ statistics ] [ summary ] [ vrf vrf-name ]

Syntax Description

ip-addr	(Optional) IPv4 source address. The format is x.x.x.x.
interface	(Optional) Interface. Use ? to determine the supported interface types.
detail	(Optional) Displays detailed adjacency information.
non-best	(Optional) Displays both the best and nonbest adjacency information.
statistics	(Optional) Displays adjacency statistics.
summary	(Optional) Displays a summary of the adjacency information.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
6.1	Modified the command output.
4.0(1)	This command was introduced.

Usage Guidelines

The counter values in the output of show ip adjacency { statistics | detail } command are cleared after a supervisor module switchover.

This command does not require a license.

Examples

This example shows how to display the adjacencies of vPC peer with G/W MAC:

switch(config)# show ip adjacency

Flags: # - Adjacencies Throttled for Glean

G - Adjacencies of vPC peer with G/W bit

IP Adjacency Table for VRF default

Total number of entries: 3

Address MAC Address Pref Source Interface

1.1.1.2 0018.bad8.457e 50 arp Ethernet2/11

10.10.10.2 0018.bad8.457e 50 arp Vlan100 G

This example shows how to display a summary of the adjacency information:

switch# show ip adjacency summary

IP AM Table - Adjacency Summary

Static : 1

Dynamic : 22

Others : 0

Total : 23

Related Commands

Command	Description
show forwarding adjacency	Displays forwarding adjacency information.

show ip adjacency summary

To display an IP adjacency summary, use the show ip adjacency summary command.

show ip adjacency summary

Syntax Description

This command has no arguments or keywords.

Defaults

None

Command Modes

Global configuration

Supported User Roles

network-admin

vdc-admin

Command History

Release	Modification
4.2(8)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display an IP adjacency summary:

switch# show ip adjacency summary

IP AM Table - Adjacency Summary

Static : 0

Dynamic : 0

Others : 0 (Throttled : 0)

Total : 0

switch#

Related Commands

Command	Description
ip arp timeout	Configures ARP.

show ip adjacency throttle statistics

To display all the throttled adjacency statistics, use the show ip adjacency throttle statistics command.

show ip adjacency throttle statistics

Syntax Description

This command has no arguments or keywords.

Defaults

None

Command Modes

Global configuration

Supported User Roles

network-admin

vdc-admin

Command History

Release	Modification
4.2(8)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display all the throttled adjacency statistics:

switch# show ip adjacency throttle statistics

No. of Adjacency hit with type INVALID: Packet count 0, Byte count 0

No. of Adjacency hit with type GLOBAL DROP: Packet count 0, Byte count 0

No. of Adjacency hit with type GLOBAL PUNT: Packet count 0, Byte count 0

No. of Adjacency hit with type GLOBAL GLEAN: Packet count 0, Byte count 0

No. of Adjacency hit with type GLEAN: Packet count 0, Byte count 0

No. of Adjacency hit with type NORMAL: Packet count 0, Byte count 0

Adjacency statistics last updated before: 00:01:05

IP Adjacency Table for VRF default

Total number of entries: 0

Address MAC Address Interface Packet Count Byte Count

switch#

Related Commands

Command	Description
show hardware proxy layer-3 detail	Displays layer-3 proxy detail information.

show ip arp

To display the Address Resolution Protocol (ARP) information, use the show ip arp command.

show ip arp [ ip-addr | interface ] [ client ] [ static ] [ statistics ] [ summary ] [ vrf vrf-name ]

Syntax Description

ip-addr	(Optional) IPv4 source address. The format is x.x.x.x.
interface	(Optional) Interface. Use ? to determine the supported interface types.
client	(Optional) Displays the ARP client table.
static	(Optional) Displays static ARP entries.
statistics	(Optional) Displays ARP statistics.
summary	(Optional) Displays a summary of the ARP table.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display a summary of the ARP table:

switch# show ip arp summary

IP ARP Table - Adjacency Summary

Resolved : 33

Incomplete : 0

Unknown : 0

Total : 33

Related Commands

Command	Description
ip arp timeout	Configures ARP.

show ip arp summary

To display an Address Resolution Protocol (ARP) adjacency summary, use the show ip arp summary command.

show ip arp summary

Syntax Description

This command has no arguments or keywords.

Defaults

None

Command Modes

Global configuration

Supported User Roles

network-admin

vdc-admin

Command History

Release	Modification
4.2(8)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display an ARP adjacency summary:

switch# show ip arp summary

IP ARP Table - Adjacency Summary

Resolved : 0

Incomplete : 0 (Throttled : 0)

Unknown : 0

Total : 0

switch#

Related Commands

Command	Description
ip arp timeout	Configures ARP.

show ip as-path-access-list

To display the Autonomous System (AS) Path access lists for the Border Gateway Protocol (BGP), use the show ip as-path-access-list command.

show ip as-path-access-list [ name ]

Syntax Description

name

(Optional) AS path access list name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the AS path access lists:

switch# show ip as-path-access-list

ip as-path access-list Test1 permit "10.0.0.1"

Related Commands

Command	Description
ip as-path access-list	Configures an AS path access list.

show ip bgp

To display entries in the Border Gateway Protocol (BGP) table, use the show ip bgp command.

show ip bgp [ ip-addr | ip-prefix [ longer-prefixes ]] [ received-paths ] [ regexp expression ] [ route-map map-name ] [ summary ] [ vrf vrf-name ]

Syntax Description

ip-addr	(Optional) Network from the BGP route table. The format is x.x.x.x.
ip-prefix	(Optional) Prefix from the BGP route table. The format is x.x.x.x/length.
longer-prefixes	(Optional) Displays the prefix and any more specific routes.
received-paths	(Optional) Displays paths stored for soft reconfiguration.
regexp expression	(Optional) Displays information that matches the regular expression.
route-map map-name	(Optional) Displays routes that match the route map. The map name can be any case-sensitive, alphanumeric string up to 63 characters.
summary	(Optional) Displays the summary of the routes.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the BGP route table:

switch(config-router)# show ip bgp

BGP routing table information for VRF default, address family IPv4 Unicast

Related Commands

Command	Description
clear ip bgp	Clears entries in the BGP route table.

show ip bgp community-list

To display Border Gateway Protocol (BGP) routes that match a community list, use the show ip bgp community-list command.

show ip bgp [ ipv4 { unicast | multicast } | all ] community-list commlist-name [ exact-match ]} [ vrf vrf-name ]

Syntax Description

ipv4	(Optional) Displays BGP information for the IPv4 address family.
ipv6	(Optional) Display BGP information for the IPv4 address family.
unicast	Displays BGP information for the unicast address family.
multicast	Displays BGP information for the multicast address family.
all	Displays BGP information for all address families.
community-list commlist-name	Display routes matching the community-list. The commlist-name can be any case-sensitive, alphanumeric string up to 63 characters.
exact-match	(Optional) Displays an exact match of the communities.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display routes that match a community list:

switch(config)# show ip bgp community-list test1

Related Commands

Command	Description
ip community-list	Creates a community list.

show ip bgp dampening

To display Border Gateway Protocol (BGP) dampening information, use the show ip bgp dampening command.

show ip bgp [ ipv4 { unicast | multicast } | all ] dampening { dampened-paths [ regexp expression ] | flap-statistics | history-paths [ regexp expression ] | parameters } [ vrf vrf-name ]

Syntax Description

ipv4	(Optional) Displays BGP information for the IPv4 address family.
ipv6	(Optional) Displays BGP information for the IPv4 address family.
unicast	Displays BGP information for the unicast address family.
multicast	Displays BGP information for the multicast address family.
all	Displays BGP information for all address families.
dampened-paths	Displays all dampened paths.
regexp expression	(Optional) Display information that matches the regular expression.
flap-statistics	Displays flap statistics for routes.
history-paths	Displays all history paths.
parameters	Displays all dampening parameters.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display dampening information:

switch(config)# show ip bgp dampening dampened-paths

Related Commands

Command	Description
show ipv6 bgp dampening	Displays BGP dampening information.

show ip bgp extcommunity

To display Border Gateway Protocol (BGP) routes that match an extended community, use the show ip bgp extcommunity command.

show ip bgp extcommunity generic { non-transitive | transitive } [ as4-number ] [ exact-match ] [ vrf vrf-name ]

Syntax Description

generic	Displays the routes that match the generic specified extended communities.
non-transitive	Displays the routes that match the non-transitive extended communities.
transitive	Displays the routes that match the transitive extended communities.
as4-number	(Optional) AS number. The as4-number is a 32-bit integer in the form of a plaintext integer or <higher 16-bit decimal number>.<lower 16-bit decimal number>.
exact-match	(Optional) Displays an exact match of the extended community.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.2(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display routes that match an extended community:

switch(config)# show ip bgp extcommunity generic transitive 1.3:30

Related Commands

Command	Description
ip extcommunity-list	Creates an extended community list.

show ip bgp extcommunity-list

To display Border Gateway Protocol (BGP) routes that match an extended community list, use the show ip bgp extcommunity-list command.

show ip bgp extcommunity-list commlist-name [ exact-match ] [ vrf vrf-name ]

Syntax Description

commlist-name	Name of an extended community-list. The commlist-name can be any case-sensitive, alphanumeric string up to 63 characters.
exact-match	(Optional) Displays an exact match of the extended communities.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.2(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display routes that match a community list:

switch(config)# show ip bgp extcommunity-list test1

Related Commands

Command	Description
ip extcommunity-list	Creates an extended community list.

show ip bgp filter-list

To display Border Gateway Protocol (BGP) routes that match a filter list, use the show ip bgp filter-list command.

show ip bgp filter-list list-name [ exact-match ] [ vrf vrf-name ]

Syntax Description

list-name	Name of a filter list. The name can be any case-sensitive, alphanumeric string up to 63 characters.
exact-match	(Optional) Displays an exact match of the filter.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display routes that match a filter list:

switch(config)# show ip bgp filter-list test1

Related Commands

Command	Description
show ipv6 bgp filter-list	Displays BGP routes that match a filter list.

show ip bgp flap-statistics

To display Border Gateway Protocol (BGP) flap statistics, use the show ip bgp flap-statistics command.

show ip bgp flap-statistics [ prefix ] [ vrf vrf-name ]

Syntax Description

prefix	(Optional) IPv6 prefix. The format is x.x.x.x/length.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the flap statistics:

switch(config)# show ip bgp flap-statistics

Related Commands

Command	Description
show ipv6 bgp	Displays BGP information.

show ip bgp history-paths

To display Border Gateway Protocol (BGP) history paths, use the show ip bgp history-paths command.

show ip bgp [ ipv4 { unicast | multicast } | all ] history-paths [ regexp expression ] [ vrf vrf-name ]

Syntax Description

ipv4	(Optional) Displays BGP information for the IPv4 address family.
unicast	Displays BGP information for the unicast address family.
multicast	Displays BGP information for the multicast address family.
all	(Optional) Displays BGP information for all address families.
history-paths	Specifies history path for the BGP information.
regexp expression	(Optional) Displays information that matches the regular expression.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display BGP history path information:

switch(config)# show ip bgp history-paths

Related Commands

Command	Description
show ipv6 bgp history-paths	Displays BGP history paths information.

show ip bgp neighbors

To display Border Gateway Protocol (BGP) neighbors, use the show ip bgp neighbors command.

show ip bgp neighbors [ addr [ advertised-routes | flap-statistics | paths | received-routes | routes [ advertised | dampened | received ]] | prefix ] [ vrf { all | vrf-name }]

Syntax Description

addr	IPv4 address. The format is x.x.x.x
advertised-routes	(Optional) Displays all the routes advertised to this neighbor.
flap-statistics	(Optional) Displays flap statistics for the routes received from this neighbor.
paths	(Optional) Displays AS paths learned from this neighbor.
received-routes	(Optional) Displays all the routes received from this neighbor.
routes	(Optional) Displays the routes received or advertised to or from this neighbor.
advertised	(Optional) Displays all the routes advertised for this neighbor.
dampened	(Optional) Displays all dampened routes received from this neighbor.
received	(Optional) Displays all the routes received from this neighbor.
prefix	(Optional) IPv6 prefix. The format is x.x.x.x/length.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.
all	(Optional) Specifies all VRF.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.
4.1(2)	Added paths keyword.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the BGP neighbors:

switch(config)# show ip bgp neighbors

Related Commands

Command	Description
show ipv6 bgp neighbors	Displays BGP information.

show ip bgp nexthop

To display Border Gateway Protocol (BGP) next hop information, use the show ip bgp nexthop command.

show ip bgp nexthop addr [ vrf vrf-name ]

Syntax Description

addr	IPv4 address. The format is x.x.x.x
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the BGP next-hop information:

switch(config)# show ip bgp nexthop 192.0.2.1

Related Commands

Command	Description
show ipv6 bgp nexthop	Displays BGP information.

show ip bgp nexthop-database

To display Border Gateway Protocol (BGP) next-hop database, use the show ip bgp nexthop-database command.

show ip bgp nexthop-database [ vrf vrf-name ]

Syntax Description

vrf vrf-name

(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the BGP next-hop database:

switch(config)# show ip bgp nexthop-database

Related Commands

Command	Description
show ipv6 bgp nexthop-database	Displays BGP information.

show ip bgp peer-policy

To display Border Gateway Protocol (BGP) peer policy template information, use the show ip bgp peer-policy command.

show ip bgp peer-policy name

Syntax Description

name

Name of a BGP template. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the BGP peer policy:

switch(config)# show ip bgp peer-policy test1

Commands configured in this template:

Send Community

Suppress Inactive

Default Originate - route-map:

Inherited commands:

Inherited by the following peers:

VRF default: 192.0.2.3

Related Commands

Command	Description
inherit peer-policy	Inherits a peer policy template for a neighbor.
template peer-policy	Configures a peer policy template.

show ip bgp peer-session

To display Border Gateway Protocol (BGP) peer session template information, use the show ip bgp peer-session command.

show ip bgp peer-session name

Syntax Description

name

Name of a BGP template. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the BGP peer session:

switch(config)# show ip bgp peer-session test1

Commands configured in this template:

Update Source - interface: Vlan33

EBGP Multihop - hop limit: 33

Inherited commands:

Inherited by the following peers:

VRF default: 192.0.2.3

Related Commands

Command	Description
inherit peer-session	Inherits a peer session template for a neighbor.
template peer-session	Configures a peer session template.

show ip bgp peer-template

To display Border Gateway Protocol (BGP) peer template information, use the show ip bgp peer-template command.

show ip bgp peer-template name

Syntax Description

name

Name of a BGP template. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the BGP peer template:

switch(config)# show ip bgp peer-template peer1

BGP peer-template is peer1

Connected check is disabled

Hold time = 0, keepalive interval is 0 seconds

Message statistics:

Sent Rcvd

Opens: 0 0

Notifications: 0 0

Updates: 0 0

Keepalives: 0 0

Route Refresh: 0 0

Capability: 0 0

Total: 0 0

Total bytes: 0 0

Bytes in queue: 0 0

Members of peer-template peer1:

default:192.0.2.3

Related Commands

Command	Description
inherit peer-template	Inherits a peer template for a neighbor.
template peer	Configures a peer template.

show ip bgp prefix-list

To display Border Gateway Protocol (BGP) routes that match a prefix list, use the show ip bgp prefix-list command.

show ip bgp prefix-list list-name [ exact-match ] [ vrf vrf-name ]

Syntax Description

list-name	Name of a prefix list. The commlist-name can be any case-sensitive, alphanumeric string up to 63 characters.
exact-match	(Optional) Displays an exact match of the filter.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display routes that match a prefix list:

switch(config)# show ip bgp prefix-list test1

Related Commands

Command	Description
show ipv6 bgp prefix-list	Displays BGP routes that match a prefix list.

show ip client

To display information about the internal IP clients, use the show ip client command.

show ip client [ name ]

Syntax Description

name

(Optional) Name of the client.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the IP client information for ARP:

switch(config)# show ip client arp

Client: arp, uuid: 268, pid: 3687, extended pid: 3687

Protocol: (none), client-index: 2, routing VRF id: 255

Data MTS-SAP: 0

Data messages, send successful: 33, failed: 0

Related Commands

Command	Description
show ip process	Displays information about the IP process.

show ip community-list

To display community lists for the Border Gateway Protocol (BGP), use the show ip community-list command.

show ip community-list [ name ]

Syntax Description

name

(Optional) Name of the community list. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the community lists:

switch(config)# show ip community-list

Standard Community List test2

permit internet local-AS

Related Commands

Command	Description
ip community-list	Configures a BGP community list.

show ip eigrp

To display a summary of the Enhanced Interior Gateway Routing Protocol (EIGRP) processes, use the show ip eigrp command.

show ip eigrp [ instance-tag ]

Syntax Description

instance-tag

(Optional) Name of the EIGRP instance. The instance-tag can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(3)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display all the EIGRP instances:

switch# show ip eigrp foo

P-EIGRP AS 0 ID 0.0.0.0 VRF default

Process-tag: foo

Status: shutdown

Authentication mode: none

Authentication key-chain: none

Metric weights: K1=1 K2=0 K3=1 K4=0 K5=0 K6=0

Rib scale: 128

metric version: 64bit

IP proto: 88 Multicast group: 224.0.0.10

Int distance: 90 Ext distance: 170

Max paths: 8

Number of EIGRP interfaces: 0 (0 loopbacks)

Number of EIGRP passive interfaces: 0

Number of EIGRP peers: 0

Graceful-Restart: Enabled

Stub-Routing: Disabled

NSF converge time limit/expiries: 120/0

NSF route-hold time limit/expiries: 240/0

NSF signal time limit/expiries: 20/0

Redistributed max-prefix: Disabled

show ip eigrp accounting

To display prefix accounting information for the Enhanced Interior Gateway Routing Protocol (EIGRP) processes, use the show ip eigrp accounting command.

show ip eigrp [ instance-tag ] accounting [ vrf { vrf-name | * }]

Syntax Description

instance-tag	(Optional) Name of the EIGRP instance. This option is available when a virtual routing and forwarding (VRF) instance is not specified. The instance tag can be any case-sensitive, alphanumeric string up to 63 characters.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.
vrf *	(Optional) Specifies all VRF instances.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display the EIGRP accounting information:

switch# show ip eigrp accounting

IP-EIGRP accounting for AS(100)/ID(192.0.2.1) vrf RED

Total Prefix Count: 4

States: A-Adjacency, P-Pending, D-Down

State Address/Source Interface Prefix Restart Restart/

Count Count Reset(s)

P Redistributed ---- 0 3 211

A 192.0.2.2 e2/1 2 0 84

P 192.0.2.4 e3/3 0 2 114

D 192.0.2.3 e4/1 0 3 0

Table 17-4 describes the significant fields shown in the display.

Table 17-4 show ip eigrp accounting Field Descriptions
Field	Description
IP-EIGRP accounting for AS...	EIGRP instance, AS number, router ID, and table ID.
Total Prefix Count:	Aggregate sum of the prefixes in an EIGRP instance topology table. The count includes prefixes learned from all neighbors or from redistribution.
States: A-Adjacency, P-Pending, D-Down	A-Adjacency: Indicates a stable adjacency with the neighbor or a normal redistribution state. P-Pending: Neighbor adjacency or redistribution is suspended or in a penalized state because the maximum prefix limit was exceeded. D-Down: Neighbor adjacency or redistribution is suspended permanently until a manual reset is performed with the clear route command.
Address/Source	Peer IP address of the redistribution source.
Prefix Count	Total number of learned prefixes by source. Note Routes can be learned for the same prefix from multiple sources, and the sum of all prefix counts in this column may be greater than the figure displayed in the “Prefix Count” field.
Restart Count	Number of times that a route source exceeded the maximum prefix limit.
Restart Reset(s)	Time, in seconds, that a route source is in a P (penalized) state. If the route source is in an A (stable or normal) state, the displayed time, in seconds, is the time period until penalization history is reset.

show ip eigrp interfaces

To display information about interfaces configured for the Enhanced Interior Gateway Routing Protocol (EIGRP), use the show ip eigrp interfaces command.

show ip eigrp [ instance-tag ] interfaces [ type instance ] [ brief ] [ vrf { vrf-name | * }]

Syntax Description

instance-tag	(Optional) Instance. The instance tag can be any case-sensitive, alphanumeric string up to 63 characters.
type	(Optional) Interface type. For more information, use the question mark (?) online help function.
instance	(Optional) Either a physical interface instance or a virtual interface instance. Specifying instance removes all entries learned through this interface from the neighbor table. The instance argument has the following syntax: Physical interface instance. Naming notation is slot/port and a slash mark between values is required as part of the notation. Virtual interface instance. The number range varies depending on the interface type. For more information about the syntax for the router, use the question mark (?) online help function.
brief	(Optional) Displays a brief summary of EIGRP interface information.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.
vrf *	(Optional) Specifies all VRF instances.

Defaults

This command shows all interfaces for the default VRF if no VRF or no interface is specified.

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.
4.0(3)	Added the brief keyword.

Usage Guidelines

Use the show ip eigrp interfaces command to determine on which interfaces EIGRP is active and learn information about EIGRP related to those interfaces.

If you specify an interface, only that interface is displayed. Otherwise, all interfaces on which EIGRP is running are displayed.

If you specify an autonomous system, only the routing process for the specified autonomous system is displayed. Otherwise, all EIGRP processes are displayed.

This command requires the Enterprise Services license.

Examples

This example shows how to display information about EIGRP interfaces:

switch# show ip eigrp interfaces brief

IP EIGRP interfaces for process 1 vrf default

Xmit Queue Mean Pacing Time Multicast Pending

Interface Peers Un/Reliable SRTT Un/Reliable Flow Timer Routes

e2/2 0 0/0 0 11/434 0 0

e2/20 1 0/0 337 0/10 0 0

e4/2 1 0/0 10 1/63 103 0

e3/2 1 0/0 330 0/16 0 0

switch#

Table 17-5 describes the significant fields shown in the display.

Table 17-5 show ip eigrp interfaces Field Descriptions
Field	Description
Interface	Interface over which EIGRP is configured.
Peers	Number of directly connected EIGRP neighbors.
Xmit Queue Un/Reliable	Number of packets remaining in the unreliable and reliable transmit queues.
Mean SRTT	Mean smoothed round-trip time (SRTT) internal (in milliseconds).
Pacing Time Un/Reliable	Pacing time used to determine when EIGRP packets should be sent out the interface (unreliable and reliable packets).
Multicast Flow Timer	Maximum number of seconds in which the router sends multicast EIGRP packets.
Pending Routes	Number of routes in the packets in the transmit queue waiting to be sent.

Related Commands

Command	Description
show ip eigrp neighbors	Displays the neighbors discovered by EIGRP.

show ip eigrp neighbors

To display information about neighbors discovered by the Enhanced Interior Gateway Routing Protocol (EIGRP), use the show ip eigrp neighbors command.

show ip eigrp [ instance-tag ] neighbors [ detail ] [ interface-type interface-instance ] [ static ] [ vrf { vrf-name | * }]

Syntax Description

instance-tag	(Optional) Name of the EIGRP instance. The instance tag can be any case-sensitive, alphanumeric string up to 63 characters.
detail	(Optional) Displays detailed EIGRP neighbor information.
interface-type	(Optional) Interface type. For more information, use the question mark (?) online help function.
interface-instance	(Optional) Either a physical interface instance or a virtual interface instance. Specifying instance removes all entries learned through this interface from the neighbor table. The instance argument has the following syntax: Physical interface instance. Naming notation is slot/port and a slash mark between values is required as part of the notation. Virtual interface instance. The number range varies depending on the interface type. For more information about the syntax for the router, use the question mark (?) online help function.
static	(Optional) Displays static EIGRP interface information.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.
vrf *	(Optional) Specifies all VRF instances.

Defaults

This command displays all neighbors for the default VRF on all interfaces if no VRF or interface is specified.

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show ip eigrp neighbors command to determine when neighbors become active and inactive. This command is also useful for debugging certain types of transport problems.

This command requires the Enterprise Services license.

Examples

This example shows how to display information about EIGRP neighbors:

switch# show ip eigrp neighbors

IP-EIGRP Neighbors for process 77 vrf default

Address Interface Holdtime Uptime Q Seq SRTT RTO

(secs) (h:m:s) Count Num (ms) (ms)

192.0.2.28 e1/3 13 0:00:41 0 11 4 20

192.0.2.2 e4/4 14 0:02:01 0 10 12 24

switch#

Table 17-6 describes the significant fields shown in the display.

Table 17-6 show ip eigrp neighbors Field Descriptions
Field	Description
process	Autonomous system number specified in the router configuration command.
vrf	VRF name.
Address	IP address of the EIGRP peer.
Interface	Interface on which the router is receiving hello packets from the peer.
Holdtime	Length of time (in seconds) that the Cisco NX-OS oftware waits to hear from the peer before declaring that the peer is down.
Uptime	Elapsed time (in hours, minutes, and seconds) since the local router first heard from this neighbor.
Q Count	Number of EIGRP packets (update, query, and reply) that the software waits to send.
Seq Num	Sequence number of the last update, query, or reply packet that was received from this neighbor.
SRTT	Smoothed round-trip time. This field indicates the number of milliseconds required for an EIGRP packet to be sent to this neighbor and for the local router to receive an acknowledgment of that packet.
RTO	Retransmission timeout (in milliseconds). This field indicates the amount of time that the software waits before resending a packet from the retransmission queue to a neighbor.

This example shows how to display detailed information about EIGRP neighbors:

switch# show ip eigrp neighbors detail

IP-EIGRP neighbors for AS 1 vrf default

H Address Interface Hold Uptime SRTT RTO Q Seq

(sec) (ms) Cnt Num

0 192.0.2.10 e1/5 14 01:00:52 3 200 0 10

Version 12.4/1.2, Retrans: 0, Retries: 0, Prefixes: 3

switch#

Table 17-7 describes the significant fields shown in the display.

Table 17-7 show ip eigrp neighbors detail Field Descriptions
Field	Description
Version	Version of EIGRP software running on the node and neighbor.
Retrans:	Number of retransmissions sent to this neighbor.
Retries:	Number of retransmissions sent to this neighbor since the last acknowledgment (ACK).
Prefixes	Number of prefixes learned from this neighbor.

Related Commands

Command	Description
clear ip eigrp neighbors	Clears neighbors for EIGRP.

show ip eigrp policy statistics

To display the policy statistics for the Enhanced Interior Gateway Routing Protocol (EIGRP), use the show ip eigrp policy statistics command in any mode.

show ip eigrp [ instance-tag ] policy statistics redistribute { bgp id | direct | eigrp id | isis id | ospf id | rip id | static } [ vrf { vrf-name | * }]

Syntax Description

instance-tag	(Optional) Name of the EIGRP instance. The instance tag can be any case-sensitive, alphanumeric string up to 63 characters.
bgp	Displays policy statistics for the Border Gateway Protocol (BGP).
direct	Displays policy statistics for directly connected routes only.
eigrp	Displays policy statistics for EIGRP.
isis	Displays policy statistics for the Intermediate-System to Intermediate-System (IS-IS) routing protocol.
ospf	Displays policy statistics for the Open Shortest Path First (OSPF) protocol.
rip	Displays policy statistics for the Routing Information Protocol (RIP).
static	Displays policy statistics for IP static routes.
id	For the bgp keyword, an autonomous system number. The range for 2-byte numbers is from 1 to 65535. The range for 4-byte numbers is from 1.0 to 65535.65535. For the eigrp keyword, an EIGRP instance name from which routes are to be redistributed. The value takes the form of a string. You can enter a decimal number, but Cisco NX-OS stores it internally as a string. For the isis keyword, an IS-IS instance name from which routes are to be redistributed. The value takes the form of a string. You can enter a decimal number, but Cisco NX-OS stores it internally as a string. For the ospf keyword, an OSPF instance name from which routes are to be redistributed. The value takes the form of a string. You can enter a decimal number, but Cisco NX-OS stores it internally as a string.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.
vrf *	(Optional) Specifies all VRF instances.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.
4.0(13	This command was removed and replaced by the show ip eigrp route-map statistics command.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display policy statistics for EIGRP:

switch(config)# show ip eigrp policy statistics redistribute direct

C: No. of comparisons, M: No. of matches

route-map rmap1 permit 1

Total accept count for policy: 10

Total reject count for policy: 0

Related Commands

Command	Description
clear ip eigrp policy statistics	Clears policy statistics for EIGRP.
show ip eigrp traffic	Displays EIGRP traffic statistics.

show ip eigrp route-map statistics

To display the route redistribution statistics for the Enhanced Interior Gateway Routing Protocol (EIGRP, use the show ip eigrp route-map statistics command in any mode.

show ip eigrp [ instance-tag ] [ route-map statistics redistribute { bgp id | direct | eigrp id | isis id | ospf id | rip id | static } vrf { vrf-name | * }]

Syntax Description

instance-tag	(Optional) Name of the EIGRP instance. The instance tag can be any case-sensitive, alphanumeric string up to 63 characters.
bgp	Displays policy statistics for the Border Gateway Protocol (BGP).
direct	Displays policy statistics for directly connected routes only.
eigrp	Displays policy statistics for EIGRP.
isis	Displays policy statistics for the Intermediate-System to Intermediate-System (IS-IS) routing protocol.
ospf	Displays policy statistics for the Open Shortest Path First (OSPF) protocol.
rip	Displays policy statistics for the Routing Information Protocol (RIP).
static	Displays policy statistics for IP static routes.
id	For the bgp keyword, an autonomous system number. The range for 2-byte numbers is from 1 to 65535. The range for 4-byte numbers is from 1.0 to 65535.65535. For the eigrp keyword, an EIGRP instance name from which routes are to be redistributed. The value takes the form of a string. You can enter a decimal number, but Cisco NX-OS stores it internally as a string. For the isis keyword, an IS-IS instance name from which routes are to be redistributed. The value takes the form of a string. You can enter a decimal number, but Cisco NX-OS stores it internally as a string. For the ospf keyword, an OSPF instance name from which routes are to be redistributed. The value takes the form of a string. You can enter a decimal number, but Cisco NX-OS stores it internally as a string.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.
vrf *	(Optional) Specifies all VRF instances.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(3)	This command was introduced.

Usage Guidelines

This command replaces the show ip eigrp policy statistics command. This command does not require a license.

Examples

This example shows how to display route-map statistics for EIGRP:

switch(config)# show ip eigrp route-map statistics redistribute direct

C: No. of comparisons, M: No. of matches

route-map rmap1 permit 1

Total accept count for policy: 10

Total reject count for policy: 0

Related Commands

Command	Description
clear ip eigrp route-map statistics	Clears route-map statistics for EIGRP.
show ip eigrp traffic	Displays EIGRP traffic statistics.

show ip eigrp topology

To display the Enhanced Interior Gateway Routing Protocol (EIGRP) topology table, use the show ip eigrp topology command.

show ip eigrp [ instance-tag ] topology [ ip-address/length ] [ active | all-links | detail-links | pending | summary | zero-successors ] [ vrf { vrf-name | * }]

Syntax Description

instance-tag	(Optional) Name of the EIGRP instance. The instance tag can be any case-sensitive, alphanumeric string up to 63 characters.
ip-address/length	(Optional) IP address in four-part, dotted-decimal notation with a network mask indicated as a slash (/) and number. For example, /8 indicates that the first 8 bits of the mask are 1s, and the corresponding bits of the address are the network address.
active	(Optional) Displays only active entries in the EIGRP topology table.
all-links	(Optional) Displays all entries in the EIGRP topology table.
detail-links	(Optional) Displays detailed information for all entries in the EIGRP topology table.
pending	(Optional) Displays all entries in the EIGRP topology table that are waiting for an update from a neighbor or are waiting to reply to a neighbor.
summary	(Optional) Displays a summary of the EIGRP topology table.
zero-successors	(Optional) Displays available routes in the EIGRP topology table.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.
vrf *	(Optional) Specifies all VRF instances.

Defaults

This command displays information for the default VRF if no VRF is specified.

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show ip eigrp topology command to determine Diffusing Update Algorithm (DUAL) states and to debug possible DUAL problems.

When you use the show ip eigrp topology command without any keywords or arguments, Cisco NX-OS displays only routes that are feasible successors.

This command requires the Enterprise Services license.

Examples

This example shows how to display the EIGRP topology table. The EIGRP metrics for specified internal routes and external routes are displayed.

switch# show ip eigrp topology 192.0.2.0/24

IP-EIGRP (AS 1): Topology entry for 192.0.2.0/24

State is Passive, Query origin flag is 1, 1 Successor(s), FD is 281600

Routing Descriptor Blocks:

192.0.2.22 (Ethernet 2/1), from 192.0.2.1, Send flag is 0x0

Composite metric is (409600/128256), Route is External

Vector metric:

Minimum bandwidth is 10000 Kbit

Total delay is 6000 microseconds

Reliability is 255/255

Load is 1/255

Minimum MTU is 1500

Hop count is 1

External data:

Originating router is 10.89.245.1

AS number of route is 0 External protocol is Connected, external metric is 0

Administrator tag is 0 (0x00000000)

switch#

This example show how to use all-links option:

switch(config)# show ip eigrp topology all-links

IP-EIGRP Topology Table for AS(100)/ID(4.4.4.4) VRF default

Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply,

r - reply Status, s - sia Status

P 3.3.3.0/24, 1 successors, FD is 130816, serno 58

via 192.168.6.2 (130816/128256), Ethernet2/2

via 192.168.5.2 (153856/128256), Ethernet2/1

P 2.2.2.0/24, 1 successors, FD is 130816, serno 57

via 192.168.6.2 (130816/128256), Ethernet2/2

via 192.168.5.2 (153856/128256), Ethernet2/1

P 1.1.1.0/24, 1 successors, FD is 130816, serno 56

via 192.168.6.2 (130816/128256), Ethernet2/2

via 192.168.5.2 (153856/128256), Ethernet2/1

P 192.168.6.0/24, 1 successors, FD is 2816, serno 25

via Connected, Ethernet2/2

via 192.168.5.2 (26112/2816), Ethernet2/1

P 6.6.6.0/24, 1 successors, FD is 128256, serno 24

via Connected, loopback6

P 5.5.5.0/24, 1 successors, FD is 128256, serno 23

via Connected, loopback5

P 4.4.4.0(1)/24, 1 successors, FD is 128256, serno 16

via Connected, loopback4

P 192.168.5.0/24, 1 successors, FD is 25856, serno 1

via Connected, Ethernet2/1

via 192.168.6.2 (3072/2816), Ethernet2/2

This example shows how to display more details:

switch(config)# show ip eigrp topology detail-links

IP-EIGRP Topology Table for AS(100)/ID(4.4.4.4) VRF default

Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply,

r - reply Status, s - sia Status

P 3.3.3.0/24, 1 successors, FD is 130816, serno 58

via 192.168.6.2 (130816/128256), Ethernet2/2

via 192.168.5.2 (153856/128256), Ethernet2/1

P 2.2.2.0/24, 1 successors, FD is 130816, serno 57

via 192.168.6.2 (130816/128256), Ethernet2/2

via 192.168.5.2 (153856/128256), Ethernet2/1

P 1.1.1.0/24, 1 successors, FD is 130816, serno 56

via 192.168.6.2 (130816/128256), Ethernet2/2

via 192.168.5.2 (153856/128256), Ethernet2/1

P 192.168.6.0/24, 1 successors, FD is 2816, serno 25

via Connected, Ethernet2/2

via 192.168.5.2 (26112/2816), Ethernet2/1

P 6.6.6.0/24, 1 successors, FD is 128256, serno 24

via Connected, loopback6

P 5.5.5.0/24, 1 successors, FD is 128256, serno 23

via Connected, loopback5

P 4.4.4.0(1)/24, 1 successors, FD is 128256, serno 16

via Connected, loopback4

P 192.168.5.0/24, 1 successors, FD is 25856, serno 1

via Connected, Ethernet2/1

via 192.168.6.2 (3072/2816), Ethernet2/2

This example shows how to display a summary of the topology table:

switch(config)# show ip eigrp topology summary

IP-EIGRP Topology Table for AS(100)/ID(4.4.4.4) VRF default

Head serial 1, next serial 59

8 routes, 0 pending replies, 0 dummies

IP-EIGRP(0) enabled on 5 interfaces, 2 neighbors present on 2 interfaces

Quiescent interfaces: Eth2/2 Eth2/1

This example shows how to display the active entries in the topology table:

switch(config-if)# show ip eigrp topology active

IP-EIGRP Topology Table for AS(101)/ID(80.86.2.3) VRF default

Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply,

r - reply Status, s - sia Status

A 8.3.2.0/24, 1 successors, FD is Inaccessible

1 replies, active 00:00:04, query-origin: Local origin

via Connected (Infinity/Infinity), loopback8

Remaining replies:

via 5.5.5.6, r, Ethernet2/6

This example shows how to display zero-successors in the topology table:

switch(config-router)# show ip eigrp topology zero-successors

IP-EIGRP Topology Table for AS(101)/ID(10.1.48.4) VRF default

Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply,

r - reply Status, s - sia Status

P 10.1.49.0/24, 0 successors, FD is Inaccessible

via 5.5.5.5 (28416/28160), Ethernet2/6

This example shows how to display pending entries:

switch(config)# show ip eigrp topology pending

IP-EIGRP Topology Table for AS(100)/ID(1.1.1.1) VRF default

Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply,

r - reply Status, s - sia Status

P 6.6.6.0/24, 1 successors, FD is 130816, U

via 192.168.5.1 (130816/128256), Ethernet2/1

P 5.5.5.0/24, 1 successors, FD is 130816, U

via 192.168.5.1 (130816/128256), Ethernet2/1

P 4.4.4.0(1)/24, 1 successors, FD is 130816, U

via 192.168.5.1 (130816/128256), Ethernet2/1

P 8.8.8.0/24, 1 successors, FD is 130816, U

via 192.168.5.1 (130816/128256), Ethernet2/1

Table 17-8 describes the significant fields shown in the display.

Table 17-8 show ip eigrp topology Field Descriptions
Field	Description
Query origin	Query origin state.
Successors	Number of feasible successors for this prefix.
FD	Feasible distance for this prefix.
192.0.2.22(Ethernet 2/1)	Next hop and interface from which this path was learned.
from 192.0.2.1	Information source for this path.
Send flag	Status of whether the sending of this prefix is pending to this neighbor.
Composite metric is...	The first number is the EIGRP metric that represents the cost to the destination. The second number is the EIGRP metric that this peer advertised.
Route is	Type of route (internal or external).
Vector Metric	Metric (bandwidth, delay, reliability, load, MTU, and hop count) advertised by the neighbor.
External Data	External information (originating router ID, AS number, external protocol, metric, and tag) advertised by the neighbor.

show ip eigrp traffic

To display the number of Enhanced Interior Gateway Routing Protocol (EIGRP) packets sent and received, use the show ip eigrp traffic command.

show ip eigrp [ instance-tag ] traffic [ vrf { vrf-name | * }]

Syntax Description

instance-tag	(Optional) Name of the EIGRP instance. The instance tag can be any case-sensitive, alphanumeric string up to 63 characters.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.
vrf *	(Optional) Specifies all VRF instances.

Defaults

This command displays information for the default VRF if no VRF is specified.

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show ip eigrp traffic command to find the number of packets sent and received by this EIGRP instance.

In addition, this command is useful in determining whether packets from one node are not reaching the neighboring node due to connectivity or configuration problems.

This command requires the Enterprise Services license.

Examples

This example shows how to display the EIGRP traffic statistics:

switch# show ip eigrp traffic

IP-EIGRP Traffic Statistics for AS 1 vrf default

Hellos sent/received: 736/797

Updates sent/received: 6/6

Queries sent/received: 0/1

Replies sent/received: 1/0

Acks sent/received: 6/6

Input queue high water mark 0, 0 drops

SIA-Queries sent/received: 0/0

SIA-Replies sent/received: 0/0

Table 17-9 describes the significant fields shown in the display.

Table 17-9 show ip eigrp traffic Field Descriptions
Field	Description
AS	Autonomous system number specified in the router eigrp command.
vrf	VRF specified in the show command.
Hellos sent/received:	Number of hello packets sent and received.
Updates sent/received:	Number of update packets sent and received.
Queries sent/received:	Number of query packets sent and received.
Replies sent/received:	Number of reply packets sent and received.
Acks sent/received:	Number of acknowledgment packets sent and received.
Input queue high water mark	Maximum number of packets in the input queue and number of drops.
SIA-Queries sent/received	Number of Stuck-in-Active query packets sent and received.
SIA-Replies sent/received:	Number of Stuck-in-Active reply packets sent and received.

show ip fib

To display forwarding information, use the show ip fib command.

show ip fib { adjacency | interfaces | route } module slot

Syntax Description

adjacency	Displays the adjacency information.
interfaces	Displays the forwarding information for interfaces on a module.
route	Displays the forwarding information for routes on a module.
module slot	Displays information for the module. The slot range depends on the hardware platform.

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show ip fib command on the supervisor to view forwarding information on a module. Optionally, you can use the attach module command to attach to a module and use the show ip fib command on the module.

This command does not require a license.

Examples

This example shows how to display forwarding information for module 2:

switch# show ip fib route module 2

IPv4 routes for table default/base

------------------+------------------+---------------------

Prefix | Next-hop | Interface

------------------+------------------+---------------------

0.0.0.0/32 Drop Null0

255.255.255.255/32 Receive sup-eth1

Related Commands

Command	Description
show forwarding	Displays information about the FIB.

show ip fib distribution

To display forwarding distribution information, use the show ip fib distribution command.

show ip fib distribution [ clients | state ]

Syntax Description

clients	(Optional) Displays the forwarding distribution information for unicast clients.
state	(Optional) Displays the forwarding distribution state for unicast Forwarding Information Base (FIB).

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display forwarding information for unicast clients:

switch# show ip fib distribution clients

id pid shmem-start shmem-end shmem-name

-- ----- ----------- --------- ----------

1 3646 0x64f70120 0x64fc0000 u6rib-ufdm

2 3647 0x64b50120 0x64d50000 urib-ufdm

Related Commands

Command	Description
show forwarding distribution	Displays distribution information about the FIB.

show ip interface

To display IP information for an interface, use the show ip interface command.

show ip interface [ type number ] [ brief ] [ vrf vrf-name ]

Syntax Description

type	(Optional) Interface type. Use ? to see the options.
number	(Optional) Interface number. Use ? to see the range.
brief	(Optional) Displays a summary of IP information.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

If the ip load-sharing per-packet command is configured, the output for the show ip interface command shows per-packet load sharing as enabled.

If the ip load-sharing per-packet command is not configured, the output of the show ip interface command shows the load sharing mode as none.

If the ip load-sharing address { destination port destination | source-destination [ port source-destination ]} [ universal-id seed ] command is configured, then the load-sharing mode can be checked by using the show ip load-sharing command.

This command does not require a license.

Examples

This example shows how to display IP information for Ethernet 4/17:

switch# show ip interface ethernet 4/17

IP Interface Status for VRF "default"(1)

Ethernet4/17, Interface status: protocol-down/link-down/admin-up, iod: 102,

IP address: 192.168.17.1, IP subnet: 192.168.17.0/24

IP broadcast address: 255.255.255.255

IP multicast groups locally joined: none

IP MTU: 1500 bytes (using link MTU)

IP primary address route-preference: 0, tag: 0

IP proxy ARP : disabled

IP Local Proxy ARP : disabled

IP multicast routing: disabled

IP icmp redirects: enabled

IP directed-broadcast: disabled

IP icmp unreachables (except port): disabled

IP icmp port-unreachable: enabled

IP unicast reverse path forwarding: none

IP load sharing: none

IP interface statistics last reset: never

IP interface software stats: (sent/received/forwarded/originated/consumed)

Unicast packets : 0/0/0/0/0

Unicast bytes : 0/0/0/0/0

Multicast packets : 0/0/0/0/0

Multicast bytes : 0/0/0/0/0

Broadcast packets : 0/0/0/0/0

Broadcast bytes : 0/0/0/0/0

Labeled packets : 0/0/0/0/0

Labeled bytes : 0/0/0/0/0

WCCP Redirect outbound: disabled

WCCP Redirect inbound: disabled

WCCP Redirect exclude: disabled

Related Commands

Command	Description
show ipv6 interface	Displays IPv6 information about an interface.

show ip load-sharing

To display IP load sharing information, use the show ip load-sharing command.

show ip load-sharing

Syntax Description

This command has no arguments or keywords.

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display IP load sharing information:

switch# show ip load-sharing

IPv4/IPv6 ECMP load sharing:

Universal-id (Random Seed): 2823428857

Load-share mode : address source-destination port source-destination Broadcast bytes : 0/0/0/0/0

Labeled packets : 0/0/0/0/0

Labeled bytes : 0/0/0/0/0

Related Commands

Command	Description
show ip load-sharing	Displays IP load sharing.

show ip mbgp

To display entries in the Multiprotocol Border Gateway Protocol (MP-BGP) table, use the show ip mbgp command.

show ip mbgp [ p-addr | ip-prefix [ longer-prefixes ]] [ received-paths ] [ regexp expression ] [ route-map map-name ] [ summary ] [ vrf vrf-name ]

Syntax Description

ip-addr	(Optional) Network from the MBGP route table. The format is x.x.x.x.
ip-prefix	(Optional) Prefix from the MBGP route table. The format is x.x.x.x/length.
longer-prefixes	(Optional) Displays the prefix and any more specific routes.
received-paths	(Optional) Displays paths stored for soft reconfiguration.
regexp expression	(Optional) Displays information that matches the regular expression.
route-map map-name	(Optional) Displays routes that match the route map. The map name can be any case-sensitive, alphanumeric string up to 63 characters.
summary	(Optional) Displays the summary of the routes.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the MBGP route table:

switch(config-router)# show ip mbgp

BGP routing table information for VRF default, address family IPv4 Multicast

Related Commands

Command	Description
clear ip mbgp	Clears entries in the MBGP route table.

show ip mbgp community

To display Multiprotocol Border Gateway Protocol (MP-BGP) routes that match a community, use the show ip mbgp community command.

show ip mbgp community [ as-number ] [ internet] [no-advertise] [no-export] [no-export-subconfed ] [ exact-match ]} [ vrf vrf-name ]

Syntax Description

as-number	Autonomous system (AS). The AS number can be a 16-bit integer or a 32-bit integer in the form of <higher 16-bit decimal number>.<lower 16-bit decimal number>.
internet	(Optional) Displays the internet community.
no-advertise	(Optional) Displays the no-advertise community.
no-export	(Optional) Displays the no-export community.
no-export-subconfed	(Optional) Displays the no-export-subconfed community.
exact-match	(Optional) Displays an exact match of the community.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display routes that match a community:

switch(config)# show ip mbgp community

Related Commands

Command	Description
ip community-list	Creates a community list.

show ip mbgp community-list

To display Multiprotocol Border Gateway Protocol (MP-BGP) routes that match a community list, use the show ip mbgp community-list command.

show ip mbgp community-list commlist-name [ exact-match ] [ vrf vrf-name ]

Syntax Description

commlist-name	Name of a community-list. The commlist-name can be any case-sensitive, alphanumeric string up to 63 characters.
exact-match	(Optional) Displays an exact match of the communities.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display routes that match a community list:

switch(config)# show ip mbgp community-list test1

Related Commands

Command	Description
ip community-list	Creates a community list.

show ip mbgp dampening

To display Multiprotocol Border Gateway Protocol (MP-BGP) dampening information, use the show ip mbgp dampening command.

show ip mbgp dampening { dampened-paths [ regexp expression ] | flap-statistics | history-paths [ regexp expression ] | parameters } [ vrf vrf-name ]

Syntax Description

dampened-paths	Displays all dampened paths.
regexp expression	(Optional) Displays information that matches the regular expression.
flap-statistics	(Optional) Displays flap statistics for routes.
history-paths	(Optional) Displays all history paths.
parameters	Displays all dampening parameters.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display dampening information:

switch(config)# show ip mbgp dampening dampened-paths

Related Commands

Command	Description
show ipv6 bgp dampening	Displays BGP dampening information.

show ip mbgp extcommunity

To display Multiprotocol Border Gateway Protocol (MP-BGP) routes that match an extended community, use the show ip mbgp extcommunity command.

show ip mbgp extcommunity generic { non-transitive | transitive } [ as4-number ] [ exact-match ] [ vrf vrf-name ]

Syntax Description

generic	Displays the routes that match the generic specific extended communities.
non-transitive	Displays the routes that match the non-transitive extended communities.
transitive	Displays the routes that match the transitive extended communities.
as4-number	AS number. The as4-number is a 32-bit integer in the form of a plaintext integer or <higher 16-bit decimal number>.<lower 16-bit decimal number>.
exact-match	(Optional) Displays an exact match of the extended community.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.2(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display routes that match an extended community:

switch(config)# show ip mbgp extcommunity generic transitive 1.3:30

Related Commands

Command	Description
ip extcommunity-list	Creates an extended community list.

show ip mbgp extcommunity-list

To display Multiprotocol Border Gateway Protocol (MP-BGP) routes that match an extended community list, use the show ip mbgp extcommunity-list command.

show ip mbgp extcommunity-list commlist-name [ exact-match ] [ vrf vrf-name ]

Syntax Description

commlist-name	Name of an extended community-list. The commlist-name can be any case-sensitive, alphanumeric string up to 63 characters.
exact-match	(Optional) Displays an exact match of the extended communities.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.2(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display routes that match a community list:

switch(config)# show ip mbgp extcommunity-list test1

Related Commands

Command	Description
ip extcommunity-list	Creates an extended community list.

show ip mbgp filter-list

To display Multiprotocol Border Gateway Protocol (MP-BGP) routes that match a filter list, use the show ip mbgp filter-list command.

show ip m bgp filter-list list-name [ exact-match ] [ vrf vrf-name ]

Syntax Description

list-name	Name of a filter list. The name can be any case-sensitive, alphanumeric string up to 63 characters.
exact-match	(Optional) Displays an exact match of the filter.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display routes that match a filter list:

switch(config)# show ip mbgp filter-list test1

Related Commands

Command	Description
show ipv6 bgp filter-list	Displays BGP routes that match a filter list.

show ip mbgp flap-statistics

To display Multiprotocol Border Gateway Protocol (MP-BGP) flap statistics, use the show ip mbgp flap-statistics command.

show ip mbgp flap-statistics [ prefix ] [ vrf vrf-name ]

Syntax Description

prefix	(Optional) IPv6 prefix. The format is x.x.x.x/length.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the flap statistics:

switch(config)# show ip mbgp flap-statistics

Related Commands

Command	Description
show ipv6 bgp	Displays BGP information.

show ip mbgp history-paths

To display Multiprotocol Border Gateway Protocol (MP-BGP) history paths, use the show ip mbgp history-paths command.

show ip mbgp history-paths [ regexp expression ] [ vrf vrf-name ]

Syntax Description

regexp expression	(Optional) Displays information that matches the regular expression.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display BGP history path information:

switch(config)# show ip mbgp history-paths

Related Commands

Command	Description
show ipv6 bgp history-paths	Displays BGP history paths information.

show ip mbgp neighbors

To display Multiprotocol Border Gateway Protocol (MP-BGP) neighbors, use the show ip mbgp neighbors command.

show ip bgp neighbors [a ddr [ advertised-routes | flap-statistics | paths | received-routes | routes [ advertised | dampened | received ]] | prefix ] [ vrf { all | vrf-name }]

Syntax Description

addr	IPv4 address. The format is x.x.x.x
advertised-routes	(Optional) Displays all the routes advertised to this neighbor.
flap-statistics	(Optional) Displays flap statistics for the routes received from this neighbor.
paths	(Optional) Displays AS paths learned from this neighbor.
received-routes	(Optional) Displays all the routes received from this neighbor.
routes	(Optional) Displays the routes received or advertised to or from this neighbor.
advertised	(Optional) Displays all the routes advertised for this neighbor.
dampened	(Optional) Displays all dampened routes received from this neighbor.
received	(Optional) Displays all the routes received from this neighbor.
prefix	(Optional) IPv6 prefix. The format is x.x.x.x/length.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.
all	(Optional) Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.
4.1(2)	Added paths keyword.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the MBGP neighbors:

switch(config)# show ip mbgp neighbors

Related Commands

Command	Description
show ipv6 bgp neighbors	Displays BGP information.

show ip mbgp nexthop

To display Multiprotocol Border Gateway Protocol (MP-BGP) next hop information, use the show ip mbgp nexthop command.

show ip mbgp nexthop addr [ vrf vrf-name ]

Syntax Description

addr	IPv4 address. The format is x.x.x.x
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the BGP next-hop information:

switch(config)# show ip mbgp nexthop 192.0.2.1

Related Commands

Command	Description
show ipv6 bgp nexthop	Displays BGP information.

show ip mbgp nexthop-database

To display Multiprotocol Border Gateway Protocol (MP-BGP) next-hop database, use the show ip mbgp nexthop-database command.

show ip mbgp nexthop-database [ vrf vrf-name ]

Syntax Description

vrf vrf-name

(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the BGP next-hop database:

switch(config)# show ip mbgp nexthop-database

Related Commands

Command	Description
show ipv6 bgp nexthop-database	Displays BGP information.

show ip mbgp prefix-list

To display Multiprotocol Border Gateway Protocol (MP-BGP) routes that match a prefix list, use the show ip mbgp prefix-list command.

show ip mbgp prefix-list list-name [ exact-match ] [ vrf vrf-name ]

Syntax Description

list-name	Name of a prefix list. The commlist-name can be any case-sensitive, alphanumeric string up to 63 characters.
exact-match	(Optional) Displays an exact match of the filter.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display routes that match a prefix list:

switch(config)# show ip mbgp prefix-list test1

Related Commands

Command	Description
show ipv6 bgp prefix-list	Displays BGP routes that match a prefix list.

show ip ospf

To display general information about Open Shortest Path First (OSPF) routing instances, use the show ip ospf command.

show ip ospf [ instance-tag ] [ vrf vrf-name ]

Syntax Description

instance-tag	(Optional) Name of the OSPF instance. Use this tag to display OSPF information about a specific OSPF instance. The instance-tag argument can be any alphanumeric string.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show ip ospf command to display information about one or more OSPF instances.

This command requires the Enterprise Services license.

Examples

This example shows how to display information about one specific OSPF instance:

switch# show ip ospf 201

Routing Process 201 with ID 192.0.2.15 vrf default

Stateful High Availability enabled

Graceful-restart is configured

Notify period: 15, grace period: 60, state: Inactive

Last graceful restart exit status: (null)

Supports only single TOS(TOS0) routes

Supports opaque LSA

Reference Bandwidth is 40000 Mbps

Initial SPF schedule delay 200.000 msecs,

minimum inter SPF delay of 1000.000 msecs,

maximum inter SPF delay of 5000.000 msecs

Minimum hold time for Router LSA throttle 5000.000 ms

Minimum hold time for Network LSA throttle 5000.000 ms

Minimum LSA arrival 1000.000 msec

Maximum paths to destination 8

Number of external LSAs 0, checksum sum 0

Number of opaque AS LSA 0, checksum sum 0

Number of areas is 2, 2 normal, 0 stub, 0 nssa

Number of active areas is 0, 0 normal, 0 stub, 0 nssa

BFD is enabled

Area BACKBONE(0) (Inactive)

Area has existed for 1w0d

Interfaces in this area: 1 Active interfaces: 0

No authentication available

SPF calculation has run 3 times

Last SPF ran for 0.000132s

Area ranges are

Number of LSAs: 0, checksum sum 0

Area (10) (Inactive)

Area has existed for 1w0d

Interfaces in this area: 1 Active interfaces: 0

No authentication available

SPF calculation has run 3 times

Last SPF ran for 0.000035s

Area ranges are

Number of LSAs: 0, checksum sum 0

Table 17-10 describes the significant fields shown in the display.

Table 17-10 show ip ospf Field Descriptions
Field	Description
Routing Process...	OSPF instance tag and OSPF router ID.
Stateful High Availability	Status of stateful restart capability.
Graceful-restart	Status of graceful restart configuration.
grace period	Number of seconds that OSPF has to trigger a graceful restart.
Last graceful restart exit status	Exit status for last graceful restart.
Supports...	Number of types of service supported (Type 0 only).
Reference Bandwidth	Bandwidth used for cost calculation.
Initial SPF schedule delay	Delay time of SPF calculations.
Minimum LSA arrival	Minimum interval between link-state advertisements.
Number of...	Number and type of link-state advertisements that have been received.
Number of areas is...	Number and type of areas configured for the router.

show ip ospf border-routers

To display the Open Shortest Path First (OSPF) routing table entries to an Area Border Router (ABR) and Autonomous System Boundary Router (ASBR), use the show ip ospf border-routers command.

show ip ospf [ instance-tag ] border-routers [ vrf vrf-name ]

Syntax Description

instance-tag	(Optional) Name of the OSPF instance. Use this tag to display OSPF information about a specific OSPF instance. The instance-tag argument can be any alphanumeric string.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show ip ospf border-routers command to display information on ABRs. and ASBRs.

This command requires the Enterprise Services license.

Examples

This example shows how to display information about border routers:

switch# show ip ospf border-routers

OSPF Process ID p1, vrf default Internal Routing Table

Codes: i - Intra-area route, I - Inter-area route

i 40.40.40.40 [10], ABR, Area 0.0.0.0, SPF 71 via

192.0.2.1, Ethernet2/1

i 60.60.60.60 [20], ABR, Area 0.0.0.0, SPF 71 via

192.0.2.1, Ethernet2/1

i 40.40.40.40 [10], ABR, Area 0.0.0.1, SPF 71 via

192.0.2.1, Ethernet2/2

i 60.60.60.60 [20], ABR, Area 0.0.0.1, SPF 71 via

192.0.2.1, Ethernet2/2

Table 17-11 describes the significant fields shown in the display.

Table 17-11 **show ip ospf border-routers** Field Descriptions
Field	Description
40.40.40.40	Router ID of the destination.
[10]	Cost of using this route.
ABR	Router type of the destination; the type is either an ABR, ASBR, or both.
Area	Area ID of the area from which this route is learned.
SPF 71	Internal number of the shortest path first (SPF) calculation that installs this route.
via 192.0.2.1	Next hop toward the destination.
Ethernet2/1	Interface type for the outgoing interface.

show ip ospf database

To display the Open Shortest Path First (OSPF) database for a specific router, use the show ip ospf database command.

show ip ospf [ instance-tag ] database [ area-id ] [ link-state-id ] [ adv-router ip-address | self-originated ] [ detail ] [ vrf vrf-name ]

show ip ospf [ instance-tag ] database asbr-summary [ area-id ] [ link-state-id ] [ adv-router ip-address | self-originated ] [ detail ] [ vrf vrf-name ]

show ip ospf [ instance-tag ] database database-summary [ vrf vrf-name ]

show ip ospf [ instance-tag ] database external [ ext_tag value ] [ link-state-id ] [ adv-router ip-address | self-originated ] [ detail ] [ vrf vrf-name ]

show ip ospf [ instance-tag ] database network [ area-id ] [ link-state-id ] [ adv-router ip-address | self-originated ] [ detail ] [ vrf vrf-name ]

show ip ospf [ instance-tag ] database nssa-external [ area-id ] [ link-state-id ] [ adv-router ip-address | self-originated ] [ detail ] [ vrf vrf-name ]

show ip ospf [ instance-tag ] database opaque-area [ area-id ] [ link-state-id ] [ adv-router ip-address | self-originated ] [ detail ] [ vrf vrf-name ]

show ip ospf [ instance-tag ] database opaque-as [ link-state-id ] [ adv-router ip-address | self-originated ] [ detail ] [ vrf vrf-name ]

show ip ospf [ instance-tag ] database opaque-link [ area-id ] [ link-state-id ] [ adv-router ip-address | self-originated ] [ detail ] [ vrf vrf-name ]

show ip ospf [ instance-tag ] database router [ area-id ] [ link-state-id ] [ adv-router ip-address | self-originated ] [ detail ] [ vrf vrf-name ]

show ip ospf [ instance-tag ] database summary [ area-id ] [ link-state-id ] [ adv-router ip-address | self-originated ] [ detail ] [ vrf vrf-name ]

Syntax Description

instance-tag	(Optional) Name of the OSPF instance. Specify as an alphanumeric string.
area-id	(Optional) Area number used to define the particular area. Specify as either an IP address or a number from 0 to 4294967295.
link-state-id	(Optional) Portion of the Internet environment that is being described by the advertisement. The value entered depends on the advertisement’s link-state type. Specify in the form of an IP address.
adv-router ip-address	(Optional) Displays all the link-state advertisements (LSAs) of the specified router.
self-originate	(Optional) Displays self-originated LSAs (from the local router).
asbr-summary	(Optional) Displays information about the autonomous system boundary router summary LSAs.
database-summary	(Optional) Displays each type of LSA for each area in the database, and the total number of LSAs.
external	(Optional) Displays information about the external LSAs.
ext_tag value	(Optional) Displays information based on an external tag. The range is from 1 to 4294967295.
network	(Optional) Displays information about the network LSAs.
nssa-external	(Optional) Displays information about the not-so-stubby area (NSSA) external LSAs.
opaque-area	(Optional) Displays information about the opaque area LSAs.
opaque-as	(Optional) Displays information about the opaque AS LSAs.
opaque-link	(Optional) Displays information about the opaque link-local LSAs.
router	(Optional) Displays information about the router LSAs.
summary	(Optional) Displays information about the summary LSAs.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the ip ospf database command to display information about different OSPF LSAs.

When the link state advertisement is describing a network, the link-state-id argument can take one of two forms:

The network’s IP address (such as Type 3 summary link advertisements and autonomous system external link advertisements).
A derived address obtained from the link state ID. (Note that masking a network links advertisement’s link state ID with the network’s subnet mask yields the network’s IP address.)
When the link state advertisement is describing a router, the link state ID is always the described router’s OSPF router ID.
When an autonomous system external advertisement (LS Type = 5) is describing a default route, its link state ID is set to Default Destination (0.0.0.0).

This command requires the Enterprise Services license.

Examples

This example shows how to display the OSPF database:

Router# show ip ospf database

OSPF Router with ID (50.50.50.50) (Process ID p1)

Router Link States (Area 0)

Link ID ADV Router Age Seq# Checksum Link Count

40.40.40.40 40.40.40.40 930 0x80000004 0x2ea1 3

50.50.50.50 50.50.50.50 935 0x80000002 0x8b52 1

60.60.60.60 60.60.60.60 943 0x800003c5 0x9854 2

Network Link States (Area 0)

Link ID ADV Router Age Seq# Checksum

209.165.201.3 60.60.60.60 944 0x80000001 0x7179

192.0.2.1 50.50.50.50 935 0x80000001 0x516a

Summary Network Link States (Area 0)

Link ID ADV Router Age Seq# Checksum

209.165.201.1 40.40.40.40 929 0x80000001 0x2498

209.165.201.1 50.50.50.50 928 0x80000001 0x5b2f

209.165.201.1 60.60.60.60 1265 0x800003c3 0xf49b

192.0.2.0 40.40.40.40 943 0x80000001 0x53f3

192.0.2.0 50.50.50.50 935 0x80000001 0x26f8

192.0.2.0 60.60.60.60 930 0x80000001 0x7b51

Table 17-12 describes the significant fields shown in the display.

Table 17-12 show ip ospf database Field Descriptions
Field	Description
Link ID	Router ID number.
ADV Router	Advertising router’s ID.
Age	Link state age.
Seq#	Link state sequence number (detects old or duplicate link state advertisements).
Checksum	Checksum of the complete contents of the link state advertisement.
Link count	Number of interfaces detected for the router.

This example shows how to display a summary of autonomous system border routers:

Router# show ip ospf database asbr-summary

OSPF Router with id(192.168.239.66) (Process ID 300)

Displaying Summary ASB Link States(Area 0.0.0.0)

LS age: 1463

Options: (No TOS-capability)

LS Type: Summary Links(AS Boundary Router)

Link State ID: 172.16.245.1 (AS Boundary Router address)

Advertising Router: 172.16.241.5

LS Seq Number: 80000072

Checksum: 0x3548

Length: 28

Network Mask: 0.0.0.0 TOS: 0 Metric: 1

Table 17-13 describes the significant fields shown in the display.

Table 17-13 show ip ospf database asbr-summary Field Descriptions
Field	Description
OSPF Router with id	Router ID number.
Process ID	OSPF process ID.
LS age	Link state age.
Options	Type of service options (Type 0 only).
LS Type	Link state type.
Link State ID	Link state ID (autonomous system boundary router).
Advertising Router	Advertising router’s ID.
LS Seq Number	Link state sequence (detects old or duplicate link state advertisements).
Checksum	Checksum of the complete contents of the link state advertisement.
Length	Length in bytes of the link state advertisement.
Network Mask	Network mask implemented.
TOS	Type of service.
Metric	Link state metric.

This example shows how to display information about external links:

Router# show ip ospf database external

OSPF Router with id(192.168.239.66) (Autonomous system 300)

Displaying AS External Link States

LS age: 280

Options: (No TOS-capability)

LS Type: AS External Link

Link State ID: 10.105.0.0 (External Network Number)

Advertising Router: 172.16.70.6

LS Seq Number: 80000AFD

Checksum: 0xC3A

Length: 36

Network Mask: 255.255.0.0

Metric Type: 2 (Larger than any link state path)

TOS: 0

Metric: 1

Forward Address: 0.0.0.0

External Route Tag: 0

Table 17-14 describes the significant fields shown in the display.

Table 17-14 show ip ospf database external Field Descriptions
Field	Description
OSPF Router with id	Router ID number.
Autonomous system	OSPF autonomous system number (OSPF process ID).
LS age	Link state age.
Options	Type of service options (Type 0 only).
LS Type	Link state type.
Link State ID	Link state ID (external network number).
Advertising Router	Advertising router’s ID.
LS Seq Number	Link state sequence number (detects old or duplicate link state advertisements).
Checksum	Checksum of the complete contents of the LSA.
Length	Length in bytes of the link state advertisement.
Network Mask	Network mask implemented.
Metric Type	External type.
TOS	Type of service.
Metric	Link state metric.
Forward Address	Forwarding address. Data traffic for the advertised destination will be forwarded to this address. If the forwarding address is set to 0.0.0.0, data traffic will be forwarded instead to the advertisement’s originator.
External Route Tag	External route tag; a 32-bit field attached to each external route. This field is not used by the OSPF protocol itself.

This example shows how to display a summary of the OSPF database:

Router# show ip ospf database database-summary

OSPF Router with ID (100.0.0.1) (Process ID 1)

Area 0 database summary

LSA Type Count Delete Maxage

Router 3 0 0

Network 0 0 0

Summary Net 0 0 0

Summary ASBR 0 0 0

Type-7 Ext 0 0 0

Self-originated Type-7 0

Opaque Link 0 0 0

Opaque Area 0 0 0

Subtotal 3 0 0

Process 1 database summary

LSA Type Count Delete Maxage

Router 3 0 0

Network 0 0 0

Summary Net 0 0 0

Summary ASBR 0 0 0

Type-7 Ext 0 0 0

Opaque Link 0 0 0

Opaque Area 0 0 0

Type-5 Ext 0 0 0

Self-originated Type-5 200

Opaque AS 0 0 0

Total 203 0 0

Table 17-15 describes the significant fields shown in the display.

Table 17-15 show ip ospf database database-summary Field Descriptions
Field	Description
Area 0 database summary	Area number.
Count	Count of LSAs of the type identified in the first column.
Router	Number of router link state advertisements in that area.
Network	Number of network link state advertisements in that area.
Summary Net	Number of summary link state advertisements in that area.
Summary ASBR	Number of summary autonomous system boundary router (ASBR) link state advertisements in that area.
Type-7 Ext	Type-7 LSA count.
Self-originated Type-7	Self-originated Type-7 LSA.
Opaque Link	Type-9 LSA count.
Opaque Area	Type-10 LSA count.
Subtotal	Sum of LSAs for that area.
Delete	Number of link state advertisements that are marked “Deleted” in that area.
Maxage	Number of link state advertisements that are marked “Maxaged” in that area.
Process 1 database summary	Database summary for the process.
Count	Count of LSAs of the type identified in the first column.
Router	Number of router link state advertisements in that process.
Network	Number of network link state advertisements in that process.
Summary Net	Number of summary link state advertisements in that process.
Summary ASBR	Number of summary autonomous system boundary router (ASBR) link state advertisements in that process.
Type-7 Ext	Type-7 LSA count.
Opaque Link	Type-9 LSA count.
Opaque Area	Type-10 LSA count.
Type-5 Ext	Type-5 LSA count.
Self-Originated Type-5	Self-originated Type-5 LSA count.
Opaque AS	Type-11 LSA count.
Total	Sum of LSAs for that process.

show ip ospf interface

To display Open Shortest Path First (OSPF)-related interface information, use the show ip ospf interface command.

show ip ospf interface [ instance-tag ] [ interface - type interface-number ] [ brief ] [ vrf vrf-name ]

Syntax Description

instance-tag	(Optional) Name of the OSPF instance. Specify as an alphanumeric string.
interface-type	(Optional) Interface type. If the interface-type argument is included, only information for the specified interface type is included. Type ? on the CLI for help on available options for this argument.
interface-number	(Optional) Interface number. If the interface-number argument is included, only information for the specified interface number is included. Type ? on the CLI for help on available options for this argument.
brief	(Optional) Displays brief overview information for OSPF interfaces, states, addresses, masks, and areas on the router.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show ip ospf interface command to display the OSPF status for the interface.

This command requires the Enterprise Services license.

Examples

This example shows how to display OSPF information for Ethernet interface 1/2:

switch# show ip ospf interface ethernet 1/2

Ethernet1/2 is up, line protocol is up

IP address 192.0.2.1, Process ID 201 vrf default, area 10

State UP, Network type BROADCAST, cost 65535

Index 2, Transmit delay 1 sec, Router Priority 1

No designated router on this network

No backup designated router on this network

0 Neighbors, flooding to 0, adjacent with 0

Timer intervals: Hello 10, Dead 40, Wait 40, Retransmit 5

Simple authentication

Number of link LSAs: 0, checksum sum 0

Table 17-16 describes the significant fields shown in the display.

Table 17-16 **show ip ospf interface** F ield Descriptions
Field	Description
Ethernet	Status of physical link and operational status of protocol.
IP Address	Interface IP address, subnet mask, and area address.
vrf	Virtual routing and forwarding (VRF) instance.
Transmit Delay	Transmit delay, interface state, and router priority.
designated router	Designated router ID and interface IP address.
backup designated router	Backup designated router ID and interface IP address.
Timer intervals	Configuration of timer intervals.
Hello	Number of seconds until next hello packet is sent out this interface.

show ip ospf lsa-content-changed-list

To display a list of all link-state advertisements (LSAs) with changed content, use the show ip ospf lsa-content-changed-list command.

show ip ospf lsa-content-changed-list neighbor-id interface-type interface-number

Syntax Description

neighbor id	Router ID for the neighbor.
interface-type	(Optional) Interface type. If the interface-type argument is included, only information for the specified interface type is included. Type ? on the CLI for help on available options for this argument.
interface-number	(Optional) Interface number. If the interface-number argument is included, only information for the specified interface number is included. Type ? on the CLI for help on available options for this argument.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display a list of LSAs that changed for Ethernet 2/1:

Router# show ip ospf lsa-content-changed-list 192.0.2.2 ethernet 2/1

show ip ospf memory

To display the memory usage statistics for the Open Shortest Path First (OSPF) protocol, use the show ip ospf memory command.

show ip ospf memory

Syntax Description

This command has no keywords or arguments.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.
4.0(3)	This command was removed.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display the memory statistics for OSPF:

Router# show ip ospf memory

OSPF Process ID sd, Memory statistics

Process memory: 2096 KB

Byte usage: needed 0, overhead 192, using 192 bytes

Allocations: current 6, created 6, failed 0, free 0

Bitfields: current 30, created 30, failed 0, free 0, using 248010 bytes

Slabs: current 2, created 2, failed 0, free 0, using 80 bytes

Index failure: Interface 0, Neighbor 0

Slab Memory

OSPF vertex slab

Alloc 1, max allocs 1, total allocs 1, total frees 0

Total block allocs 1, total block frees 0, max blocks 1

Bytes (size/allocated) 68/69720

OSPF IPv4 prefix routes slab

Alloc 0, max allocs 0, total allocs 0, total frees 0

Total block allocs 0, total block frees 0, max blocks 0

Bytes (size/allocated) 188/64

OSPF router routes slab

Alloc 0, max allocs 0, total allocs 0, total frees 0

Total block allocs 0, total block frees 0, max blocks 0

Bytes (size/allocated) 100/64

OSPF IPv4 next-hops slab

Alloc 1, max allocs 1, total allocs 1, total frees 0

Total block allocs 1, total block frees 0, max blocks 1

Bytes (size/allocated) 32/262232

show ip ospf neighbors

To display Open Shortest Path First (OSPF)-neighbor information on a per-interface basis, use the show ip ospf neighbor command.

show ip ospf [ instance-tag ] neighbors [ interface - type interface-number ] [ neighbor-id ] [ detail ] [ summary ] [ vrf vrf-name ]

Syntax Description

instance-tag	(Optional) Name of the OSPF instance. Specify as an alphanumeric string.
area-id	(Optional) Area number used to define the particular area. Specify as an IP address or a number from 0 to 4294967295.
interface-type	(Optional) Interface type. If the interface-type argument is included, only information for the specified interface type is included. Type ? on the CLI for help on available options for this argument.
interface-number	(Optional) Interface number. If the interface-number argument is included, only information for the specified interface number is included. Type ? on the CLI for help on available options for this argument.
neighbor-id	(Optional) Router ID of the neighbor. Specify as an IP address.
detail	(Optional) Displays all neighbors given in detail (lists all neighbors).
summary	(Optional) Displays a summary of the neighbors.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show ip ospf neighbors command to display information about all or some of the neighbors for this OSPF instance.

This command requires the Enterprise Services license.

Examples

This example shows how to display the summary information about the neighbor that matches the neighbor ID:

Router# show ip ospf neighbors 10.199.199.137

Neighbor 10.199.199.137, interface address 192.0.2.37

In the area 0.0.0.0 via interface Ethernet2/1

Neighbor priority is 1, State is FULL

Options 2

Dead timer due in 0:00:32

Link State retransmission due in 0:00:04

Neighbor 10.199.199.137, interface address 209.165.201.189

In the area 0.0.0.0 via interface Ethernet4/3

Neighbor priority is 5, State is FULL

Options 2

Dead timer due in 0:00:32

Link State retransmission due in 0:00:03

This example shows how to display the neighbors that match the neighbor ID on an interface:

Router# show ip ospf neighbors ethernet 2/1 10.199.199.137

Neighbor 10.199.199.137, interface address 192.0.2.37

In the area 0.0.0.0 via interface Ethernet2/1

Neighbor priority is 1, State is FULL

Options 2

Dead timer due in 0:00:37

Link State retransmission due in 0:00:04

This example shows how to display detailed information about OSPF neighbors:

Router# show ip ospf neighbors detail

Neighbor 192.168.5.2, interface address 10.225.200.28

In the area 0 via interface GigabitEthernet1/0/0

Neighbor priority is 1, State is FULL, 6 state changes

DR is 10.225.200.28 BDR is 10.225.200.30

Options is 0x42

LLS Options is 0x1 (LR), last OOB-Resync 00:03:08 ago

Dead timer due in 00:00:36

Neighbor is up for 00:09:46

Index 1/1, retransmission queue length 0, number of retransmission 1

First 0x0(0)/0x0(0) Next 0x0(0)/0x0(0)

Last retransmission scan length is 1, maximum is 1

Last retransmission scan time is 0 msec, maximum is 0 msec

Table 17-17 describes the significant fields shown in the displays.

Table 17-17 **show ip ospf neighbor detail** Field Descriptions
Field	Description
Neighbor	Neighbor router ID.
interface address	IP address of the interface.
In the area	Area and interface through which the OSPF neighbor is known.
Neighbor priority	Router priority of the neighbor.
State	OSPF state.
state changes	Number of state changes since the neighbor was created.This value can be reset using the clear ip ospf counters neighbor command.
DR is	Router ID of the designated router for the interface.
BDR is	Router ID of the backup designated router for the interface.
Options	Hello packet options field contents. (E-bit only. Possible values are 0 and 2; 2 indicates the area is not a stub; 0 indicates the area is a stub.)
LLS Options..., last OOB-Resync	Link-Local Signaling and out-of-band (OOB) link-state database resynchronization performed hours:minutes:seconds ago (NSF information). The field indicates the last successful out-of-band resynchronization with the NSF-capable router.
Dead timer due in	Expected time before Cisco NX-OS declares the neighbor dead.
Neighbor is up for	Number of hours:minutes:seconds since the neighbor went into a two-way state.
Index	Neighbor location in the area-wide and autonomous system-wide retransmission queue.
retransmission queue length	Number of elements in the retransmission queue.
number of retransmission	Number of times that update packets have been resent during flooding.
First	First memory location of the flooding details.
Next	Next memory location of the flooding details.
Last retransmission scan length	Number of link state advertisements (LSAs) in the last retransmission packet.
maximum	Maximum number of LSAs sent in any retransmission packet.
Last retransmission scan time	Time taken to build last retransmission packet.
maximum	Maximum time taken to build any retransmission packet.

show ip ospf policy statistics area

To display Open Shortest Path First (OSPF) policy statistics for an area, use the show ip ospf policy statistics area command.

show ip ospf [ instance-tag ] policy statistics area area id filter-list { in | out } [ vrf vrf-name ]

Syntax Description

instance-tag	(Optional) Name of the OSPF instance. Specify as an alphanumeric string.
area area-id	Specifies the area number used to define the particular area. Specify as an IP address or a number from 0 to 4294967295.
filter-list	Filters prefixes between OSPF areas.
in	Displays policy statistics for incoming routes.
out	Displays policy statistics for outgoing routes.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show ip ospf policy statistics area command to display information about the filter lists applied to an area.

This command requires the Enterprise Services license.

Examples

This example shows how to display policy statistics for OSPF:

switch# show ip ospf policy statistics area 201

show ip ospf policy statistics redistribute

To display Open Shortest Path First (OSPF) policy statistics, use the show ip ospf policy statistics redistribute command.

show ip ospf [ instance-tag ] policy statistics redistribute { bgp id | direct | eigrp id | isis id | ospf id | rip id | static } [ vrf vrf-name ]

Syntax Description

instance-tag	(Optional) Name of the OSPF instance. Specify as an alphanumeric string.
bgp	Displays policy statistics for the Border Gateway Protocol (BGP).
direct	Displays policy statistics for directly connected routes only.
eigrp	Displays policy statistics for the Enhanced Interior Gateway Routing Protocol (EIGRP).
isis	Displays policy statistics for the Intermediate-System to Intermediate-System (IS-IS) routing protocol.
ospf	Displays policy statistics for OSPF.
rip	Displays policy statistics for the Routing Information Protocol (RIP).
static	Displays policy statistics for IP static routes.
id	For the bgp keyword, an autonomous system number. The range for 2-byte numbers is from 1 to 65535. The range for 4-byte numbers is from 1.0 to 65535.65535. For the eigrp keyword, an autonomous system number. The range is from 1 to 65535. For the isis. ospf, and rip keywords, an instance name from which routes are to be redistributed. The value takes the form of a string. You can enter a decimal number, but Cisco NX-OS stores it internally as a string.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show ip ospf policy statistics redistribute command to display redistribution statistics.

This command requires the Enterprise Services license.

Examples

This example shows how to display policy statistics for redistributed routes:

switch# show ip ospf policy statistics redistribute

show ip ospf request-list

To display a list of all link-state advertisements (LSAs) requested by a router, use the show ip ospf request-list command.

show ip ospf request-list neighbor-id interface interface - number

Syntax Description

neighbor-id	Router ID of the neighbor. Specify as an IP address.
interface-type	Interface type. If the interface-type argument is included, only information for the specified interface type is included. Type ? on the CLI for help on available options for this argument.
interface-number	Interface number. If the interface-number argument is included, only information for the specified interface number is included. Type ? on the CLI for help on available options for this argument.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show ip ospf request-list command to troubleshoot Open Shortest Path First (OSPF) routing operations.

This command requires the Enterprise Services license.

Examples

This example shows how to display a list of all LSAs requested by a router:

Router# show ip ospf request-list 40.40.40 ethernet 2/1

OSPF Process ID p1

Neighbor 40.40.40.40, interface Ethernet2/1, address 192.0.2.1

1 LSAs on request-list

Type LS ID ADV RTR Seq NO Age Checksum

1 192.0.2.12 192.0.2.12 0x8000020D 8 0x6572

Table 17-18 describes the significant fields shown in the displays.

Table 17-18 **show ip ospf request-list** Field Descriptions
Field	Description
Type	LSA type.
LS ID	IP address of the neighbor router.
ADV RTR	IP address of the advertising router.
Seq NO	Packet sequence number of the LSA.
Age	Age, in seconds, of the LSA.
Checksum	Checksum number of the LSA.

show ip ospf retransmission-list

To display a list of all link-state advertisements (LSAs) waiting to be resent to neighbors, use the show ip ospf retransmission-list command.

show ip ospf retransmission-list neighbor-id interface interface - number

Syntax Description

neighbor-id	Router ID of the neighbor. Specify as an IP address.
interface-type	Interface type. If the interface-type argument is included, only information for the specified interface type is included. Type ? on the CLI for help on available options for this argument.
interface-number	Interface number. If the interface-number argument is included, only information for the specified interface number is included. Type ? on the CLI for help on available options for this argument.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show ip ospf retransmission-list command to troubleshoot Open Shortest Path First (OSPF) routing operations.

This command requires the Enterprise Services license.

Examples

This example shows how to display all LSAs waiting to be resent to neighbors:

Router# show ip ospf retransmission-list 192.0.2.11 ethernet 2/1

OSPF Router with ID (192.0.2.12) (Process ID 1)

Neighbor 192.0.2.11, interface Ethernet2/1 address 209.165.201.11

Link state retransmission due in 3764 msec, Queue length 2

Type LS ID ADV RTR Seq NO Age Checksum

1 192.0.2.12 192.0.2.12 0x80000210 0 0xB196

Table 17-19 describes the significant fields shown in the displays.

Table 17-19 **show ip ospf retransmission-list** Field Descriptions
Field	Description
Type	LSA type.
LS ID	IP address of the neighbor router.
ADV RTR	IP address of the advertising router.
Seq NO	Packet sequence number of the LSA.
Age	Age, in seconds, of the LSA.
Checksum	Checksum number of the LSA.

show ip ospf routes

To display the Open Shortest Path First (OSPF) topology table, use the show ip ospf routes command.

show ip ospf [ instance-tag ] routes [ prefix / length | summary } [ vrf vrf-name ]

Syntax Description

instance-tag	(Optional) Name of the OSPF instance. Specify as an alphanumeric string.
prefix /length	(Optional) IP prefix, which limits output to a specific route. Indicate the length as a slash (/) and number from 1 to 31. For example, /8 indicates that the first eight bits in the IP prefix are network bits.
summary	(Optional) Displays a summary of all routes.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show ospf routes command to display the OSPF private routing table (which contains only routes that are calculated by OSPF). If something is wrong with a route in the routing information base (RIB), then you should check the OSPF copy of the route to determine if it matches the RIB contents. If it does not match, a synchronization problem exists between OSPF and the RIB.

This command requires the Enterprise Services license.

Examples

This example shows how to display OSPF routes:

RP/0/RP0/CPU0:router# show ip ospf routes

OSPF Process ID sd vrf default, Routing Table

(D) denotes route is directly attached (R) denotes route is in RIB

61.61.61.61/32 (i) area 1

via 192.168.2.1/Ethernet2/2, cost 21

100.100.2.0/24 (i) area 1

via 192.168.2.1/Ethernet2/22, cost 20

192.168.2.0/24 (i) area 1

via directly connected

Table 17-20 describes the significant fields shown in the display.

Table 17-20 **show ospf route** Field Descriptions
Field	Description
61.61.61.61/32	Router ID for the router that advertised this route.
via...	Packets destined for the given prefix are sent over the listed interface or directly connected to this device.

show ip ospf statistics

To display Open Shortest Path First (OSPF) shortest path first (SPF) calculation statistics, use the show ip ospf statistics command.

show ip ospf [ instance-tag ] statistics [ vrf vrf-name ]

Syntax Description

instance-tag	(Optional) Name of the OSPF instance. Specify as an alphanumeric string up to 20 characters.
vrf vrf-name	(Optional) Name of the VRF. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show ip ospf statistics command to display information about link-state advertisements (LSAs). This information can be useful for both OSPF network maintenance and troubleshooting. For example, we recommend that you use the show ip ospf statistics command as the first troubleshooting step for LSA flapping.

This command requires the Enterprise Services license.

Examples

This example shows how to display information about the SPF calculations:

Router# show ip ospf statistics

OSPF Process p1 vrf default, Event statistics (cleared 2w3d ago)

Router ID changes: 0

DR elections: 50

Older LSAs received: 16

Neighbor state changes: 82

Neighbor dead postponed: 0

Neighbor dead interval expirations: 2

Neighbor bad lsreqs: 0

Neighbor sequence number mismatches: 0

SPF computations: 101 full, 23 summary, 23 external

LSA Type Generated Refreshed Flushed Aged out

Router 41 1678 4 3

Network 12 2 15 1

Summary Net 53 6 120 6

Summary ASBR 0 0 0 0

AS External 0 0 0 0

Opaque Link 0 0 0 0

Opaque Area 0 0 0 0

Opaque AS 0 0 0 0

Following counters can not be reset:

LSA deletions: 0 pending, 14 hwm, 183 deleted, 14 revived, 27 runs

Hello queue: 0/200, hwm 2, drops 0

Flood queue: 0/100, hwm 2, drops 0

LSDB additions failed: 0

Buffers: in use hwm permanent alloc free

128 bytes 0 2 2 350300 350300

512 bytes 0 2 2 114 114

1520 bytes 0 0 0 0 0

4500 bytes 0 1 1 355 355

huge 0 0 0 0 0

Table 17-21 describes the significant fields shown in the display.

Table 17-21 **show ip ospf statistics** F ield Descriptions
Field	Description
OSPF process	Unique value assigned to the OSPF instance in the configuration.
vrf	Virtual routing and forwarding (VRF) for this OSPF instance.
DR elections	Number of times that a new designated router was elected.
Neighbor...	Details about neighbors.
LSA Type	Number of each type of LSA sent.
Hello queue	Queue of hello packets to be processed: current number in queue/maximum number allowed in queue hwm—high water mark. The maximum number of packets ever stored in the queue. drops—The number of packets dropped because the queue was full.
flood queue	Queue of flood packets to be processed.
buffers	Chunks of memory used to store packets.

show ip ospf summary-address

To display a list of all summary address redistribution information configured in an Open Shortest Path First (OSPF) instance, use the show ip ospf summary-address command.

show ip ospf [ instance-tag ] summary-address [ vrf vrf-name ]

Syntax Description

instance-tag	(Optional) Name of the OSPF instance. Specify as an alphanumeric string.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about summary addresses:

Router# show ip ospf summary-address

OSPF Process 2, Summary-address

10.2.0.0/255.255.0.0 Metric -1, Type 0, Tag 0

10.2.0.0/255.255.0.0 Metric -1, Type 0, Tag 10

Table 17-17 describes the significant fields shown in the displays.

Table 17-22 **show ip ospf summary-address** Field Descriptions
Field	Description
10.2.0.0/255.255.0.0	IP address and mask of the router for the OSPF process.
Metric -1	OSPF metric type.
Type 0	Type of LSA.
Tag 0	OSPF process tag identifier.

show ip ospf traffic

To display Open Shortest Path First (OSPF) traffic statistics, use the show ip ospf traffic command.

show ip ospf [ instance-tag ] traffic [ vrf vrf-name ]

Syntax Description

instance-tag	(Optional) Name of the OSPF instance. Specify as an alphanumeric string.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show ip ospf traffic command to display traffic statistics for one or more OSPF instances.

This command requires the Enterprise Services license.

Examples

This example shows how to display OSPF traffic statistics:

Router# show ip ospf traffic

OSPF Process ID p1, vrf Red, Packet Counters (cleared 2w3d ago)

Total: 1690 in, 349230 out

LSU transmissions: first 100, rxmit 108, for req 16

Flooding packets output throttled (IP/tokens): 0 (0/0)

Ignored LSAs: 0, LSAs dropped during SPF: 0

LSAs dropped during graceful restart: 0

Errors: drops in 0, drops out 0, errors in 0

errors out 0, unknown in 0, unknown out 0

no ospf 0, bad version 0, bad crc 0

dup rid 0, dup src 0, invalid src 0

invalid dst 0, no nbr 0, passive 0

wrong area 0, nbr changed rid/ip addr 0

bad auth 0

hellos dbds lsreqs lsus acks

In: 1411 70 16 136 57

Out: 348871 62 4 224 69

Table 17-23 describes the significant fields shown in the display.

Table 17-23 show ospf traffic Field Descriptions
Field	Description
OSPF Process	OSPF instance tag for these traffic statistics.
vrf	Virtual routing and forwarding (VRF) for this OSPF instance.
Errors
drops	Number of packets dropped.
bad version	Number of packets received with bad version.
dup rid	Number of packets with a duplicate router-id.
dup src	Number of packets with a duplicate source address.
no nbr	Number of packets from a router that is not a full neighbor.
nbr changed rid/ip addr	Number of packets with router-id/ip address pair not matching our neighbor's values.
lsreq	Number of packets of type LSREQ (LSA required).
lsacks	Number of packets of type LSACK (LSA acknowledged).s

Related Commands

Command	Description
clear ip ospf traffic	Clears OSPF traffic statistics.

show ip ospf virtual-links

To display parameters and the current state of Open Shortest Path First (OSPF) virtual links, use the show ip ospf virtual-links command.

show ip ospf [ instance-tag ] virtual-links [ brief ] [ vrf vrf-name ]

Syntax Description

instance-tag	(Optional) Instance tag. Specify as an alphanumeric string.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.
instance-tag	(Optional) Instance tag. Use this tag to display OSPF information about a specific OSPF instance.
brief	(Optional) Displays a summary of the configured virtual links.
vrf vrf-name	(Optional) Name of the OSPF VRF. The vrf-name argument can be specified as an arbitrary string. The strings “default” and “all” are reserved vrf-names.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

Use the show ip ospf virtual-links command to display information about configured virtual links.

This command requires the Enterprise Services license.

Examples

This example shows how to display information about virtual links:

Router# show ip ospf virtual-links

Virtual link 2 to router 40.40.40.40 is up

Process ID p1 vrf default, Transit area 1, via interface Ethernet1/2, cost 10

Local Address 192.0.2.2, Remote Address 192.0.2.1

Index 4, Transmit delay 1 sec

1 Neighbors, flooding to 1, adjacent with 1

Timer intervals: hello 10, dead 40, wait 40, retransmit 5

Hello timer due in 00:00:04

No authentication

Number of link LSAs: 0, checksum sum 0

Neighbor State is FULL, 4 state changes, last change 00:00:03

Hello options 0x2, dbd options 0x42

Last non-hello packet received 00:00:01

Dead timer due in 00:00:36

Table 17-24 describes the significant fields shown in the display.

Table 17-24 **show ip ospf virtual-links** Field Descriptions
Field	Description
Virtual Link	OSPF neighbor and whether the link to that neighbor is up or down.
vrf	Virtual routing and forwarding (VRF) for this OSPF instance.
Transit area...	Transit area through which the virtual link is formed.
via interface...	Interface through which the virtual link is formed.
cost	Cost of reaching the OSPF neighbor through the virtual link.
Transmit delay	Transmit delay (in seconds) on the virtual link.
Timer intervals...	Various timer intervals configured for the link.
Hello timer due in 0:00:04	Time when the next hello is expected from the neighbor.

show ip policy

To display the route policy information, use the show ip policy command.

show ip policy [ vrf vrf-name ]

Syntax Description

vrf vrf-name

(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows the policies attached to interfaces:

switch(config-if)# show ip policy

Interface Route-map Status VRF-Name

Ethernet2/45 floor1 Inactive --

Related Commands

Command	Description
ip policy	Configures a route policy on an interface.

show ip prefix-list

To display prefix lists for the Border Gateway Protocol (BGP), use the show ip prefix-list command.

show ip prefix-list [ name ]

Syntax Description

name

(Optional) Name of community list. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the prefix lists:

switch(config)# show ip prefix-list

ip prefix-list test2: 1 entries

seq 5 permit 10.0.0.0/8

Related Commands

Command	Description
ip prefix-list	Configures a BGP prefix list.

show ip process

To display information about the IP process, use the show ip process command.

show ip process [ vrf vrf-name ]

Syntax Description

vrf vrf-name

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows details on the IP process:

switch(config)# show ip process

VRF default

VRF id is 1

Base table id is 1

Auto discard is disabled

Auto discard is not added

Auto Null broadcast is configured

Auto Punt broadcast is configured

Static discard is not configured

Number of static default route configured is 0

Number of ip unreachable configured is 0

Iodlist: 80

Local address list:

Related Commands

Command	Description
show ipv6 process	Displays information about the IPv6 process.

show ip rip

To display the configuration and status of the Routing Information Protocol (RIP), use the show ip rip command in any mode.

show ip rip [ instance-tag ] [ vrf vrf-name ]

Syntax Description

instance-tag	(Optional) Selects a RIP instance.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.

Defaults

No default behavior or values

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display RIP information:

switch(config-if)# show ip rip

Process Name "rip-sd" vrf "default"

RIP port 520, multicast-group 224.0.0.9

Admin-distance: 40

Updates every 30 sec, expire in 180 sec

Collect garbage in 120 sec

Default-metric: 1

Max-paths: 8

Process is up and running

Interfaces supported by ipv4 RIP :

Ethernet1/2

Table 17-25 describes the significant fields shown in the display.

Table 17-25 show ip rip Field Descriptions
Field	Description
Process Name	RIP instance tag.
Admin-distance	Administrative distance assigned to RIP. You can configure this value using the distance command in router address-family configuration mode.
Updates	Timer value for RIP updates. Configure this value with the ip rip timer basic command in interface configuration mode.
expire	Timer value for expiring RIP updates. Configure this value with the ip rip timer basic command in interface configuration mode.
Collect garbage	Timer value for garbage collecting in the RIP route table. Configure this value with the ip rip timer basic command in interface configuration mode.
Default metric	Default metric value. Configure this value with the default-metric command in router address-family mode.
Max-paths	Number of maximum paths allowed per RIP route. Configure this value with the max-paths command in router address-family mode.
Process	Administrative and operational state of this RIP instance.
Interfaces supported	RIP version and list of interfaces configured for this RIP instance. Add or remove interfaces using the ip router rip command in interface configuration mode.

Related Commands

Command	Description
show ip rip interface	Displays RIP information for an interface.
show ip rip policy statistics	Displays RIP policy statistics.
show ip rip route	Displays RIP route information.
show ip rip statistics	Displays RIP statistics.

show ip rip interface

To display interface entry information from the Routing Information Protocol (RIP) topology table, use the show ip rip interface command in any mode.

show ip rip interface [ type instance ] [ vrf vrf-name ]

Syntax Description

interface type slot/port	(Optional) Specifies the interface.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.

Defaults

This command has no default settings.

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display interface entry information from the RIP topology table:

switch(config-if)# show ip rip interface ethernet 1/2

Process Name "rip-sd" vrf "default"

RIP-configured interface information

GigabitEthernet1/2, protocol-down/link-down/admin-down, RIP state : down

address/mask NotConfigured, metric 1, split-horizon

Table 17-26 describes the significant fields shown in the display.

Table 17-26 show ip rip interface Field Descriptions
Field	Description
Process Name	RIP instance tag.
vrf	Virtual routing and forwarding (VRF) of this interface.
Interface information	Interface administrative and operational state.
RIP state	RIP information for this interface.

Related Commands

Command	Description
show ip rip	Displays RIP information.
show ip rip policy statistics	Displays RIP policy statistics.
show ip rip route	Displays RIP route information.
show ip rip statistics	Displays RIP statistics.

show ip rip neighbor

To display the neighbor information from the Routing Information Protocol (RIP) topology table, use the command in any mode.

show ip rip neighbor [ interface-type instance ] [ vrf vrf-name ]

Syntax Description

interface-type	(Optional) Interface type. For more information, use the question mark (?) online help function.
instance	(Optional) Either a physical interface instance or a virtual interface instance.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.

Defaults

No default behavior or values

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

The following example shows how to display neighbor information from the RIP topology table:

switch(config-if)#

Process Name "rip-sd" vrf "default"

RIP Neighbor Information (number of neighbors = 0)

('dead' means more than 300 seconds ago)

Table 17-27 describes the significant fields shown in the display.

Table 17-27 Field Descriptions
Field	Description
Process Name	RIP instance tag.
vrf	Virtual routing and forwarding (VRF) of this interface.
Neighbor information	Number of RIP neighbors recognized on this interface.

Related Commands

Command	Description
show ip rip	Displays RIP information.
show ip rip interface	Displays RIP information for an interface.
show ip rip policy statistics	Displays RIP policy statistics.
show ip rip route	Displays RIP route information.
show ip rip statistics	Displays RIP statistics.

show ip rip policy statistics

To display the policy statistics for the Routing Information Protocol (RIP), use the show ip rip policy statistics command in any mode.

show ip rip policy statistics redistribute { bgp id | direct | eigrp id | isis id | ospf id | ospfv3 id | static } [ vrf vrf-name ]

Syntax Description

bgp	Displays policy statistics for the Border Gateway Protocol (BGP).
direct	Displays policy statistics for directly connected routes only.
eigrp	Displays policy statistics for Enhanced Interior Gateway Routing Protocol (EIGRP).
isis	Displays policy statistics for Intermediate-System to Intermediate-System (IS-IS) routing protocol.
ospf	Displays policy statistics for Open Shortest Path First (OSPF) protocol.
ospfv3	Displays policy statistics for Open Shortest Path First version 3 (OSPFv3) protocol.
static	Displays policy statistics for IP static routes.
id	For the bgp keyword, an autonomous system number. The range for 2-byte numbers is from 1 to 65535. The range for 4-byte numbers is from 1.0 to 65535.65535. For the eigrp keyword, an EIGRP instance name from which routes are to be redistributed. The value takes the form of a string. You can enter a decimal number, but Cisco NX-OS stores it internally as a string. For the isis keyword, an IS-IS instance name from which routes are to be redistributed. The value takes the form of a string. You can enter a decimal number, but Cisco NX-OS stores it internally as a string. For the ospf keyword, an OSPF instance name from which routes are to be redistributed. The value takes the form of a string. You can enter a decimal number, but Cisco NX-OS stores it internally as a string.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.

Defaults

No default behavior or values.

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display policy statistics for EIGRP:

switch# show ip rip policy statistics redistribute eigrp 201

Related Commands

Command	Description
clear ip rip policy statistics	Clears policy statistics for RIP.
show ip rip	Displays RIP information.
show ip rip interface	Displays RIP information for an interface.
show ip rip route	Displays RIP route information.
show ip rip statistics	Displays RIP statistics.

show ip rip route

To display route information from the Routing Information Protocol (RIP) topology table, use the show ip rip route command in any mode.

show ip rip route [ prefix/length ] [ summary ] [ vrf vrf-name ]

Syntax Description

prefix/length	(Optional) IP or IPv6 prefix about which routing information should be displayed.
summary	(Optional) Displays information about summary routes.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.

Defaults

No default behavior or values

Command Modes

Any

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

The following is sample output from the show ip rip route command:

:switch# show ip rip route

Related Commands

Command	Description
show ip rip	Displays RIP information.
show ip rip interface	Displays RIP information for an interface.
show ip rip policy statistics	Displays policy statistics for RIP.
show ip rip statistics	Displays RIP statistics.

show ip rip statistics

To display statistical entry information from the Routing Information Protocol (RIP) topology table, use the show ip rip statistics command in any mode.

show ip rip statistics [ interface-type instance ] [ vrf vrf-name ]

Syntax Description

interface-type	(Optional) Interface type. For more information, use the question mark (?) online help function.
instance	(Optional) Either a physical interface instance or a virtual interface instance.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.

Command Default

No default behavior or values.

Command Modes

Any

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example is sample output from the show ip rip statistics command:

switch# show ip rip statistics

Global update stats:

Sent Multicast Updates: periodic 0,triggered 0

Sent Multicast Requests: 0

Sent Unicast Updates: 544

Sent Unicast Requests: 544

Recv Multicast Updates: 0

Recv Multicast Requests: 0

Recv Unicast Updates: 500

Recv Unicast Requests: 544

Recv Bad Pkts: 0

Recv Bad Routes: 0

Table 17-28 describes the significant fields shown in the display.

Table 17-28 show rip statistics Field Descriptions
Field	Description
Sent Multicast Updates:	Number of RIP multicast updates sent.
Sent Multicast Requests:	Number of RIP multicast requests sent.
Sent Unicast Updates:	Number of RIP unicast updates sent.
Sent Unicast Requests:	Number of RIP unicast requests sent.
Recv Multicast Updates:	Number of RIP multicast updates received.
Recv Multicast Requests:	Number of RIP multicast requests received.
Recv Unicast Updates:	Number of RIP unicast updates received.
Recv Unicast Requests:	Number of RIP unicast requests received.
Recv Bad Pkts:	Number of bad RIP packets received.
Recv Bad Routes:	Number of bad RIP routes received.

Related Commands

Command	Description
show ip rip	Displays RIP information.
show ip rip interface	Displays RIP information for an interface.
show ip rip policy statistics	Displays policy statistics for RIP.
show ip rip route	Displays RIP route information.

show ip route

To display routes from the unicast RIB, use the show ip route command.

Syntax Description

all	(Optional) Displays all routes.
addr	(Optional) IPv4 address. The format is x.x.x.x.
hostname	(Optional) Host name. The name can be any case-sensitive, alphanumeric string up to 80 characters.
prefix	(Optional) IPv4 prefix. The format is x.x.x.x/length. The length range is from 1 to 32.
route-type	(Optional) Type of route. Use ? to see the list of types.
interface type number	(Optional) Displays the routes for an interface. Use ? to see the supported interfaces.
next-hop addr	(Optional) Displays routes with this next-hop address. The format is x.x.x.x.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(3)	This command was introduced.
4.1(2)	Added hostname argument.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the route table:

switch(config)# show ip route all

IP Route Table for VRF "default"

'*' denotes best ucast next-hop '**' denotes best mcast next-hop

'[x/y]' denotes [preference/metric]

0.0.0.0/32, 1 ucast next-hops, 0 mcast next-hops

*via Null0, [220/0], 00:45:24, local, discard

255.255.255.255/32, 1 ucast next-hops, 0 mcast next-hops

*via sup-eth1, [0/0], 00:45:24, local

Related Commands

Command	Description
clear ip route	Clears entries in the route table.

show ip static-route

To display static routes from the unicast RIB, use the show ip static-route command.

show ip static-route [ vrf { vrf-name | all }]

Syntax Description

vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.
all	(Optional) Specifies all virtual router contexts (VRF) name.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.
4.2(1)	Added all keyword.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the static routes:

switch(config)# show ip static-route

IPv4 Unicast Static Routes:

Total number of routes: 0, unresolved: 0

Related Commands

Command	Description
ip route	Configures a static route.

show ip static-route track-table

To display information on the IPv4 or IPv6 static-route track table, use the show ip static-route track-table command.

show {ipv4 | ipv6} static-route track-table

Syntax Description

This command does not have any arguments or keywords.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
6.2(2)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about the IPv4 or IPv6 static-route track table:

switch# show ip static-route track-table

Static-route for VRF "default"(1)

IPv4 Unicast Static Routes:

0.0.0.0/0, configured nh: 0.0.0.0/32 Null0

(installed in urib)

rnh(not installed in urib)

switch(config)#

Related Commands

Command	Description
ip route track	Configures a static route associated with the track object.

show ip traffic

To display IP traffic information, use the show ip traffic command.

show ip traffic

Syntax Description

This command has no keywords or arguments.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the IP traffic information:

switch(config)# show ip traffic

IP Software Processed Traffic Statistics

----------------------------------------

Transmission and reception:

Packets received: 14121, sent: 3415, consumed: 0,

Forwarded, unicast: 0, multicast: 0, Label: 0

Opts:

end: 0, nop: 0, basic security: 0, loose source route: 0

timestamp: 0, extended security: 0, record route: 0

stream ID: 0, strict source route: 0, alert: 45, cipso: 0, ump: 0

other: 0

Errors:

Bad checksum: 0, packet too small: 0, bad version: 0,

Bad header length: 0, bad packet length: 0, bad destination: 0,

Bad ttl: 0, could not forward: 126, no buffer dropped: 0,

Bad encapsulation: 0, no route: 0, non-existent protocol: 0

Fragmentation/reassembly:

Fragments received: 0, fragments sent: 0, fragments created: 0,

Fragments dropped: 0, packets with DF: 0, packets reassembled: 0,

Fragments timed out: 0

ICMP Software Processed Traffic Statistics

------------------------------------------

Transmission:

Redirect: 0, unreachable: 0, echo request: 0, echo reply: 1,

Mask request: 0, mask reply: 0, info request: 0, info reply: 0,

Parameter problem: 0, source quench: 0, timestamp: 0,

Timestamp response: 0, time exceeded: 0,

Irdp solicitation: 0, irdp advertisement: 0

Reception:

Redirect: 0, unreachable: 337, echo request: 1, echo reply: 0,

Mask request: 0, mask reply: 0, info request: 0, info reply: 0,

Parameter problem: 0, source quench: 0, timestamp: 0,

Timestamp response: 0, time exceeded: 0,

Irdp solicitation: 0, irdp advertisement: 0,

Format error: 0, checksum error: 0

Statistics last reset: never

Related Commands

Command	Description
show ip process	Displays information about the IP process.

show ip wccp

To display global statistics that are related to the Web Cache Communication Protocol (WCCP), use the show ip wccp command.

show ip wccp [ vrf vrf-name ] [ service-number | web-cache ] [ detail | mask | service | view ]

Syntax Description

vrf vrf-name	(Optional) Specifies the VRF in which the service group needs to be created. If no VRF is specified, then the service number is created in the default global VRF. The vrf-name can be any case-sensitive, alphanumeric string up to 32 characters.
service-number	(Optional) Dynamic service identifier. The service-number range is from 1 to 255.
web-cache	(Optional) Displays information about the web-cache well-known service.
detail	(Optional) Displays information about the device and all web caches.
mask	(Optional) Displays information about the WCCP mask.
service	(Optional) Displays information about the WCCP service.
view	(Optional) Displays information about the members of a service group that have or have not been detected.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.2(0) to 6.1(0)	Changed the command output.
4.2(1)	This command was introduced.

Usage Guidelines

Use the show ip wccp service-number command to provide the Total Packets Redirected count. The Total Packets Redirected count is the number of flows, or sessions, that are redirected.

Use the show ip wccp service-number detail command to provide the Packets Redirected count. The Packets Redirected count is the number of flows, or sessions, that are redirected.

This command does not require a license.

Examples

This example shows how to display the WCCP information:

switch# show ip wccp

Global WCCP information:

Router information:

Router Identifier: 10.10.12.10

Protocol Version: 2.0

Service Identifier: 61

Number of Service Group Clients: 1

Number of Service Group Routers: 1

Service mode: Open

Service Access-list: -none-

Redirect Access-list: -none-

Service Identifier: 62

Number of Service Group Clients: 1

Number of Service Group Routers: 1

Service mode: Open

Service Access-list: -none-

Redirect Access-list: -none-

switch#

Table 17-29 describes the significant fields shown in the display.

Table 17-29 show ip wccp Field Descriptions
Field	Description
Service Identifier	Service that is detailed.
Number of Service Group Clients	Number of clients in the service group.
Number of Service Group Routers	Number of routers in the service group.
Service mode	WCCP service mode. Options are open or closed.
Service Access-list	Named IP access list that defines the packets that match the service.
Redirect Access-list	Name of the access list that determines which packets are redirected.

This example shows how to display the WCCP group member details for service 10:

switch(config)# show ip wccp 10 view

WCCP Router Informed of:

10.168.88.10

10.168.88.20

WCCP Cache Engines Visible

10.168.88.11

10.168.88.12

WCCP Cache Engines Not Visible:

-none-

If any cache engine is displayed under the WCCP Cache Engines Not Visible field, the router needs to be reconfigured to map the cache engine that is not visible to it.

Table 17-30 describes the significant fields shown in the display.

Table 17-30 show ip wccp view Field Descriptions
Field	Description
WCCP Router Informed of	List of routers detected by the current router.
WCCP Clients Visible	List of clients that is visible to the router and other clients in the service group.
WCCP Clients Not Visible	List of clients in the service group that is not visible to the router and other clients in the service group.

This example shows how to display the WCCP client information and WCCP router statistics that include the type of services:

switch(config)# show ip wccp 91 detail

WCCP Client information:

WCCP Client ID: 10.1.1.1

Protocol Version: 2.0

State: Usable (Usable)

Redirection: L2

Packet Return: L2

Packets Redirected: 0

Connect Time: 00:01:15

Assignment: MASK

Bypassed Packets: 0

Mask SrcAddr DstAddr SrcPort DstPort

---- ------- ------- ------- -------

0001: 0x00000001 0x00000000 0x0000 0x0000

Value SrcAddr DstAddr SrcPort DstPort CE-IP

----- ------- ------- ------- ------- -----

0001: 0x00000000 0x00000000 0x0000 0x0000 0x0a010101 (10.1.1.1)

0002: 0x00000001 0x00000000 0x0000 0x0000 0x0a010101 (10.1.1.1)

Table 17-31 describes the significant fields shown in the display.

Table 17-31 show ip wccp detail Field Descriptions
Field	Description
WCCP Router information	Header for the area that contains fields for the IP address and version of WCCP associated with the router connected to the cache engine in the service group.
IP Address	IP address of the router connected to the cache engine in the service group.
WCCP Client Information	Header for the area that contains fields for information on clients.
IP Address	IP address of the cache engine in the service group.
State	Whether the cache engine is operating properly and can be contacted by a router and other cache engines in the service group.
Packets Redirected	Number of packets that are redirected to the cache engine.
Connect Time	Amount of time that the cache engine is connected to the router.
Bypassed Packets	Number of packets that-are bypassed.

Related Commands

Command	Description
clear ip wccp	Clears the counter for packets redirected by WCCP.
ip wccp	Enables WCCP on a router and specifies the type of services to be used.
show ip interface	Lists a summary of the IP information and status of an interface.

show ipv6 adjacency

To display adjacency information, use the show ipv6 adjacency command.

show ipv6 adjacency [ ipv6-addr | interface ] [ detail ] [ non-best ] [ statistics ] [ summary ] [ vrf vrf-name ]

Syntax Description

ipv6-addr	(Optional) An IPv6 source address. The format is A:B::C:D
interface	(Optional) An interface. Use ? to determine the supported interface types.
detail	(Optional) Displays detailed adjacency information.
non-best	(Optional) Displays the best adjacency entries and the alternate adjacency entries.
statistics	(Optional) Displays adjacency statistics.
summary	(Optional) Displays a summary of the adjacency information.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
6.1	Modified the command output.
4.2(1)	Added non-best and summary keywords.
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display IPv6 adjacency table information:

switch(config)# show ipv6 adjacency

Flags: # - Adjacencies Throttled for Glean

G - Adjacencies of vPC peer with G/W bit

IPv6 Adjacency Table for VRF default

Total number of entries: 1

Address Age MAC Address Pref Source Interface

10::20 07:52:52 0018.bad8.457e 50 icmpv6 Vlan100 G

This example shows how to display a summary of the adjacency information:

switch# show ipv6 adjacency summary

IPv6 Adjacency Table for VRF default

Total number of entries: 0

Address Age MAC Address Pref Source Interface

Related Commands

Command	Description
show forwarding adjacency	Displays forwarding adjacency information.

show ipv6 bgp

To display entries in the Border Gateway Protocol (BGP) table, use the show ipv6 bgp command.

show iv6p bgp [ ipv6-addr | ipv6-prefix [ longer-prefixes ]] [ received-paths ] [ regexp expression ] [ route-map map-name ] [ summary] [vrf vrf-name ]

Syntax Description

ipv6-addr	(Optional)A network from the BGP route table. The format is A:B::C:D.
ipv6-prefix	(Optional) A prefix from the BGP route table. The format isA:B::C:D/length.
longer-prefixes	(Optional) Displays the prefix and any more specific routes.
received-paths	(Optional) Displays paths stored for soft reconfiguration.
regexp expression	(Optional) Display information that matches the regular expression.
route-map map-name	(Optional) Displays routes that match the route map. The map name can be any case-sensitive, alphanumeric string up to 63 characters.
summary	(Optional) Displays the summary of the routes.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the BGP route table:

switch(config-router)# show ipv6 bgp

BGP routing table information for VRF default, address family IPv6 Unicast

Related Commands

Command	Description
clear bgp	Clears entries in the BGP route table.

show ipv6 bgp community

To display Border Gateway Protocol (MP-BGP) routes that match a community, use the show ipv6 bgp community command.

show iv6 bgp community [ as-number ] [ internet] [no-advertise] [no-export] [no-export-subconfed ] [ exact-match ]} [ vrf vrf-name ]

Syntax Description

as-number	AS number. The AS number can be a 16-bit integer or a 32-bit integer in the form of <higher 16-bit decimal number>.<lower 16-bit decimal number>.
internet	(Optional) Displays the internet community.
no-advertise	(Optional) Displays the no-advertise community.
no-export	(Optional) Displays the no-export community.
no-export-subconfed	(Optional) Displays the no-export-subconfed community.
exact-match	(Optional) Displays an exact match of the community.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display routes that match a community:

switch(config)# show ipv6 bgp community

Related Commands

Command	Description
ip community-list	Creates a community list.

show ipv6 bgp community-list

To display Border Gateway Protocol (BGP) routes that match a community list, use the show ipv6 bgp community-list command.

show ipv6 bgp [ community-list commlist-name [ exact-match ]} [ vrf vrf-name ]

Syntax Description

community-list commlist-name	Display routes matching the community-list. The commlist-name can be any case-sensitive, alphanumeric string up to 63 characters.
exact-match	(Optional) Displays an exact match of the communities.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display routes that match a community list:

switch(config)# show ipv6 bgp community-list test1

Related Commands

Command	Description
ip community-list	Creates a community list.

show ipv6 bgp dampening

To display Border Gateway Protocol (BGP) dampening information, use the show ipv6 bgp dampening command.

show ipv6 bgp dampening { dampened-paths [ regexp expression ] | flap-statistics | history-paths [ regexp expression ] | parameters } [ vrf vrf-name ]

Syntax Description

dampened-paths	Display all dampened paths.
regexp expression	(Optional) Display information that matches the regular expression.
flap-statistics	Displays flap statistics for routes.
history-paths	Displays all history paths.
parameters	Displays all dampening parameters.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display dampening information:

switch(config)# show ipv6 bgp dampening dampened-paths

Related Commands

Command	Description
show ip bgp dampening	Displays BGP dampening information.

show ipv6 bgp extcommunity-list

To display Border Gateway Protocol (BGP) routes that match an extended community list, use the show ipv6 bgp extcommunity-list command.

show ipv6 bgp extcommunity-list commlist-name [ exact-match ] [ vrf vrf-name ]

Syntax Description

commlist-name	Name of an extended community-list. The commlist-name can be any case-sensitive, alphanumeric string up to 63 characters.
exact-match	(Optional) Displays an exact match of the extended communities.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.2(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display routes that match a community list:

switch(config)# show ipv6 bgp extcommunity-list test1

Related Commands

Command	Description
ip extcommunity-list	Creates an extended community list.

show ipv6 bgp filter-list

To display Border Gateway Protocol (BGP) routes that match a filter list, use the show ipv6 bgp filter-list command.

show ipv6 bgp filter-list list-name [ exact-match ] [ vrf vrf-name ]

Syntax Description

list-name	Name of a filter-list. The commlist-name can be any case-sensitive, alphanumeric string up to 63 characters.
exact-match	(Optional) Displays an exact match of the filter.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display routes that match a filter list:

switch(config)# show ipv6 bgp filter-list test1

Related Commands

Command	Description
show ip bgp filter-list	Displays BGP routes that match a filter list.

show ipv6 bgp flap-statistics

To display Border Gateway Protocol (BGP) flap statistics, use the show ipv6 bgp flap-statistics command.

show ipv6 bgp flap-statistics [ prefix ] [ vrf vrf-name ]

Syntax Description

prefix	(Optional) IPv6 prefix. The format is A:B::C:D/length.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the flap statistics:

switch(config)# show ipv6 bgp flap-statistics

Related Commands

Command	Description
show ip bgp	Displays BGP information.

show ipv6 bgp history-paths

To display Border Gateway Protocol (BGP) history paths, use the show ipv6 bgp history-paths command.

show ipv6 bgp history-paths [ regexp expression ] [ vrf vrf-name ]

Syntax Description

regexp expression	(Optional) Display information that matches the regular expression.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display BGP history path information:

switch(config)# show ipv6 bgp history-paths

Related Commands

Command	Description
show ip bgp history-paths	Displays BGP history paths information.

show ipv6 bgp neighbors

To display Border Gateway Protocol (BGP) neighbors, use the show ipv6 bgp neighbors command.

show ipv6 bgp neighbors [ addr [ advertised-routes | flap-statistics | paths | received-routes | routes [ advertised | dampened | received ]] | prefix ] [ vrf { all | vrf-name }]

Syntax Description

addr	IPv6 address. The format is A:B::C:D.
advertised-routes	(Optional) Displays all the routes advertised to this neighbor.
flap-statistics	(Optional) Displays flap statistics for the routes received from this neighbor.
paths	(Optional) Displays AS paths learned from this neighbor.
received-routes	(Optional) Displays all the routes received from this neighbor.
routes	(Optional) Displays the routes received or advertised to or from this neighbor.
advertised	(Optional) Displays all the routes advertised for this neighbor.
dampened	(Optional) Displays all dampened routes received from this neighbor.
received	(Optional) Displays all the routes received from this neighbor.
prefix	(Optional) IPv6 prefix. The format is A:B::C:D/length.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.
all	(Optional) Specifies all VRFS.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.
4.1(2)	Added paths keyword.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the BGP neighbors:

switch(config)# show ipv6 bgp neighbors

Related Commands

Command	Description
show ip bgp neighbors	Displays BGP information.

show ipv6 bgp nexthop

To display Border Gateway Protocol (BGP) next hop information, use the show ipv6 bgp nexthop command.

show ipv6 bgp nexthop addr [ vrf vrf-name ]

Syntax Description

addr	IPv4 address. The format is A:B::C:D.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the BGP next-hop information:

switch(config)# show ipv6 bgp nexthop 2001:0DB8::1

Related Commands

Command	Description
show ip bgp nexthop	Displays BGP information.

show ipv6 bgp nexthop-database

To display Border Gateway Protocol (BGP) next-hop database, use the show ipv6 bgp nexthop-database command.

show ipv6 bgp nexthop-database [ vrf vrf-name ]

Syntax Description

vrf vrf-name

(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the BGP next-hop database:

switch(config)# show ipv6 bgp nexthop-database

Related Commands

Command	Description
show ip bgp nexthop-database	Displays BGP information.

show ipv6 bgp prefix-list

To display Border Gateway Protocol (BGP) routes that match a prefix list, use the show ipv6 bgp prefix-list command.

show ipv6 bgp prefix-list list-name [ exact-match ] [ vrf vrf-name ]

Syntax Description

list-name	Name of a prefix list. The commlist-name can be any case-sensitive, alphanumeric string up to 63 characters.
exact-match	(Optional) Displays an exact match of the filter.
vrf vrf-name	(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display routes that match a prefix list:

switch(config)# show ipv6 bgp prefix-list test1

Related Commands

Command	Description
show ip bgp prefix-list	Displays BGP routes that match a prefix list.

show ipv6 client

To display information about the internal IPv6 clients, use the show ipv6 client command.

show ipv6 client [ name ]

Syntax Description

name

(Optional) Name of client.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
4.0(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the IPv6 client information for ICMPv6:

switch(config-if)# show ipv6 client icmpv6

IPv6 Registered Client Status

Client: icmpv6, status: up, pid: 3688, extended pid: 3688

Protocol: 58, pib-index: 2, routing context id: 255

Control mts SAP: 1551

Data mts SAP: 1552

IPC messages to control mq: 3

IPC messages to data mq: 0

Related Commands

Command	Description
show ipv6 process	Displays information about the IPv6 process.

show ipv6 eigrp

To display a summary of the Enhanced Interior Gateway Routing Protocol (EIGRP) for IPv6 processes, use the show ipv6 eigrp command.

show ipv6 eigrp [ instance-tag ]

Syntax Description

instance-tag

(Optional) Name of the EIGRP instance. The instance tag can be any case-sensitive, alphanumeric string up to 63 characters.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.1(2)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display all the EIGRP for IPv6 instances:

switch# show ipv6 eigrp

IP-EIGRP AS 0 ID 0.0.0.0 VRF default

Process-tag: Test1

Status: shutdown

Authentication mode: none

Authentication key-chain: none

Metric weights: K1=1 K2=0 K3=1 K4=0 K5=0

IP proto: 88 Multicast group: ff02::000a

Int distance: 90 Ext distance: 170

Max paths: 8

Number of EIGRP interfaces: 0 (0 loopbacks)

Number of EIGRP peers: 0

show ipv6 eigrp accounting

To display prefix accounting information for the Enhanced Interior Gateway Routing Protocol (EIGRP) for IPv6 processes, use the show ipv6 eigrp accounting command.

show ipv6 eigrp [ instance-tag ] accounting [ vrf { vrf-name | * }]

Syntax Description

instance-tag	(Optional) Name of the EIGRP instance. This option is available when a virtual routing and forwarding (VRF) instance is not specified. The instance tag can be any case-sensitive, alphanumeric string up to 63 characters.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.
vrf *	(Optional) Specifies all VRF instances.

Defaults

None

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.1(2)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display the EIGRP accounting information:

switch# show ipv6 eigrp accounting

IPv6-EIGRP accounting for AS(100)/ID(192.0.2.1) vrf RED

Total Prefix Count: 4

States: A-Adjacency, P-Pending, D-Down

State Address/Source Interface Prefix Restart Restart/

Count Count Reset(s)

P Redistributed ---- 0 3 211

A 2001:0DB8::2 e2/1 2 0 84

P 2001:0DB8::3 e3/3 0 2 114

D 2001:0DB8::4 e4/1 0 3 0

Table 17-4 describes the significant fields shown in the display.

Table 17-32 show ipv6 eigrp accounting Field Descriptions
Field	Description
IPv6-EIGRP accounting for AS...	EIGRP instance, AS number, router ID, and table ID.
Total Prefix Count:	Aggregate sum of the prefixes in an EIGRP instance topology table. The count includes prefixes learned from all neighbors or from redistribution.
States: A-Adjacency, P-Pending, D-Down	A-Adjacency—Indicates a stable adjacency with the neighbor or a normal redistribution state. P-Pending—Neighbor adjacency or redistribution is suspended or in a penalized state because the maximum prefix limit was exceeded. D-Down—Neighbor adjacency or redistribution is suspended permanently until a manual reset is performed with the clear route command.
Address/Source	Peer IP address of the redistribution source.
Prefix Count	Total number of learned prefixes by source. Note Routes can be learned for the same prefix from multiple sources, and the sum of all prefix counts in this column may be greater than the figure displayed in the “Prefix Count” field.
Restart Count	Number of times that a route source exceeded the maximum prefix limit.
Restart Reset(s)	Time, in seconds, that a route source is in a P (penalized) state. If the route source is in an A (stable or normal) state, the displayed time, in seconds, is the time period until penalization history is reset.

show ipv6 eigrp interfaces

To display information about interfaces configured for the Enhanced Interior Gateway Routing Protocol (EIGRP) for IPv6, use the show ipv6 eigrp interfaces command.

show ipv6 eigrp [ instance-tag ] interfaces [ type instance ] [ brief ] [ vrf { vrf-name | * }]

Syntax Description

instance-tag	(Optional) Name of the EIGRP instance. The instance tag can be any case-sensitive, alphanumeric string up to 63 characters.
vrf *	(Optional) Specifies all VRF instances.
type	(Optional) Interface type. For more information, use the question mark (?) online help function.
instance	(Optional) Either a physical interface instance or a virtual interface instance. Specifying instance removes all entries learned through this interface from the neighbor table. For more information, use the question mark (?) online help function.
brief	(Optional) Displays a brief summary of EIGRP interface information.
vrf vrf-name	(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-insensitive alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.

Defaults

This command shows all interfaces for the default VRF if no VRF or interface is specified.

Command Modes

Any

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
4.1(2)	This command was introduced.

Usage Guidelines

Use the show ipv6 eigrp interfaces command to determine on which interfaces EIGRP is active and to learn information about EIGRP related to those interfaces.

If you specify an interface, only that interface is displayed. Otherwise, all interfaces on which EIGRP is running are displayed.

If you specify an autonomous system, only the routing process for the specified autonomous system is displayed. Otherwise, all EIGRP processes are displayed.

This command requires the Enterprise Services license.

Examples

This example shows how to display information about EIGRP interfaces:

switch# show ipv6 eigrp interfaces brief

IPv6 EIGRP interfaces for process 1 vrf default

Xmit Queue Mean Pacing Time Multicast Pending

Interface Peers Un/Reliable SRTT Un/Reliable Flow Timer Routes

e2/2 0 0/0 0 11/434 0 0

e2/20 1 0/0 337 0/10 0 0

e4/2 1 0/0 10 1/63 103 0

e3/2 1 0/0 330 0/16 0 0

switch#

Table 17-5 describes the significant fields shown in the display.

Table 17-33 show ip eigrp interfaces Field Descriptions
Field	Description
Interface	Interface over which EIGRP is configured.
Peers	Number of directly connected EIGRP neighbors.
Xmit Queue Un/Reliable	Number of packets remaining in the unreliable and reliable transmit queues.
Mean SRTT	Mean smoothed round-trip time (SRTT) internal (in milliseconds).
Pacing Time Un/Reliable	Pacing time used to determine when EIGRP packets should be sent out the interface (unreliable and reliable packets).
Multicast Flow Timer	Maximum number of seconds in which the router sends multicast EIGRP packets.
Pending Routes	Number of routes in the packets in the transmit queue waiting to be sent.

Related Commands

Command