Cisco Firepower 4100/9300 Upgrade Guide, Firepower 6.0.1–7.0.x or ASA 9.4(1)–9.16(x) with FXOS 1.1.1–2.10.1

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Book Contents
Find Matches in This Book
Available Languages
Download Options

Book Title

Cisco Firepower 4100/9300 Upgrade Guide, Firepower 6.0.1–7.0.x or ASA 9.4(1)–9.16(x) with FXOS 1.1.1–2.10.1

Chapter Title

Monitor Upgrade Progress and Verify Installation

Results

Updated:
October 26, 2018

Chapter: Monitor Upgrade Progress and Verify Installation

Monitor Upgrade Progress and Verify Installation

Monitor the Upgrade Progress

You can monitor the upgrade process using the FXOS CLI:

Procedure

Step 1

Connect to the FXOS CLI.

Step 2

Enter scope system .

Step 3

Enter show firmware monitor .

Step 4

Wait for all components (FPRM, Fabric Interconnect, and Chassis) to show Upgrade-Status: Ready.

Note 

After the FPRM component is upgraded, the system will reboot and then continue upgrading the other components.

Example

Firepower-chassis# scope system
Firepower-chassis /system # show firmware monitor 
FPRM:
    Package-Vers: 2.3(1.58)
    Upgrade-Status: Ready

Fabric Interconnect A:
    Package-Vers: 2.3(1.58)
    Upgrade-Status: Ready

Chassis 1:
    Server 1:
        Package-Vers: 2.3(1.58)
        Upgrade-Status: Ready
    Server 2:
        Package-Vers: 2.3(1.58)
        Upgrade-Status: Ready

Verify the Installation

Enter the following commands to verify the status of the security modules/security engine and any installed applications:

Procedure

Step 1

Connect to the FXOS CLI.

Step 2

Enter top .

Step 3

Enter scope ssa .

Step 4

Enter show slot .

Step 5

Verify that the Admin State is Ok and the Oper State is Online for the security engine on a Firepower 4100 series appliance or for any security modules installed on a Firepower 9300 appliance.

Example:
Step 6

Enter show app-instance .

Step 7

Verify that the Oper State is Online for any logical devices installed on the chassis and that the correct version is listed.

If this chassis is part of a cluster, verify that the cluster operational state is “In-Cluster” for all security modules installed in the chassis. Also, verify that the control unit is not on the chassis for which you are upgrading—there should not be any instance with Cluster Role set to “Master”.

Example

Firepower-chassis# scope ssa
Firepower-chassis /ssa # show slot

Slot:
    Slot ID    Log Level Admin State  Oper State
    ---------- --------- ------------ ----------
    1          Info      Ok           Online
    2          Info      Ok           Online
    3          Info      Ok           Not Available
Firepower-chassis /ssa #
Firepower-chassis /ssa # show app-instance
App Name   Identifier Slot ID    Admin State Oper State       Running Version Startup Version Cluster State   Cluster Role
---------- ---------- ---------- ----------- ---------------- --------------- --------------- --------------- ------------
asa        asa1       1          Enabled     Online           9.10.0.85       9.10.0.85       Not Applicable  None
asa        asa2       2          Enabled     Online           9.10.0.85       9.10.0.85       Not Applicable  None
Firepower-chassis /ssa #

Was this Document Helpful?

FeedbackFeedback

Contact Cisco