Read the Regulatory Compliance and Safety Information document before installing the chassis.

Take note of the following warnings:

Warning

Statement 1071—Warning Definition IMPORTANT SAFETY INSTRUCTIONS Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Read the installation instructions before using, installing, or connecting the system to the power source. Use the statement number provided at the end of each warning statement to locate its translation in the translated safety warnings for this device. SAVE THESE INSTRUCTIONS

Warning

Statement 1005—Circuit Breaker This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not great than: 250 V, 15 A.

Warning

Statement 1006—Chassis Warning for Rack-Mounting and Servicing To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety: This unit should be mounted at the bottom of the rack if it is the only unit in the rack. When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack. If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack.

Warning

Statement 1015—Battery Handling To reduce risk of fire, explosion or leakage of flammable liquid or gas: Replace the battery only with the same or equivalent type recommended by the manufacturer. Do not dismantle, crush, puncture, use sharp tool to remove, short external contacts, or dispose of in fire. Do not use if battery is warped or swollen. Do not store or use battery in a temperature > 60° C. Do not store or use battery in low air pressure environment < 69.7 kPa.

Warning

Statement 1017—Restricted Area This unit is intended for installation in restricted access areas. A restricted access area can be accessed by skilled, instructed, or qualified personnel.

Warning

Statement 1019—Main Disconnecting Device The plug-socket combination must be accessible at all times, because it serves as the main disconnecting device.

Warning

Statement 1053—Class 1M Laser Radiation Hazard level 1M invisible laser radiation is present. Do not view directly with nonattenuating optical instruments.

Warning

Statement 1047—Overheating Prevention To prevent the system from overheating, do not operate it in an area that exceeds the maximum recommended ambient temperature of: 95° F (35° C).

Warning

Statement 1074—Comply with Local and National Electrical Codes To reduce risk of electric shock or fire, installation of the equipment must comply with local and national electrical codes.

Observe these safety guidelines:

• Keep the area clear and dust free before, during, and after installation.

• Keep tools away from walkways, where you and others might trip over them.

• Do not wear loose clothing or jewelry, such as earrings, bracelets, or chains that could get caught in the chassis.

• Wear safety glasses if you are working under any conditions that might be hazardous to your eyes.

• Do not perform any action that creates a potential hazard to people or makes the equipment unsafe.

• Never attempt to lift an object that is too heavy for one person.

Warning

Before working on a chassis, be sure the power cord is unplugged.

Read the Regulatory Compliance and Safety Information document before installing the chassis.

Follow these guidelines when working on equipment powered by electricity:

• Before beginning procedures that require access to the interior of the chassis, locate the emergency power-off switch for the room in which you are working. Then, if an electrical accident occurs, you can act quickly to turn off the power.

• Do not work alone if potentially hazardous conditions exist anywhere in your work space.

• Never assume that power is disconnected; always check.

• Look carefully for possible hazards in your work area, such as moist floors, ungrounded power extension cables, frayed power cords, and missing safety grounds.

• If an electrical accident occurs:

  • Use caution; do not become a victim yourself.

  • Disconnect power from the chassis.

  • If possible, send another person to get medical aid. Otherwise, assess the condition of the victim, and then call for help.

  • Determine whether the person needs rescue breathing or external cardiac compressions; then take appropriate action.

• Use the chassis within its marked electrical ratings and product usage instructions.

• The Cisco Content Security Appliance x95 Series are equipped with an AC-input power supply, which is shipped with a three-wire electrical cord with a grounding-type plug that fits into a grounding-type power outlet only. Do not circumvent this safety feature. Equipment grounding should comply with local and national electrical codes.

ESD occurs when electronic components are improperly handled, and it can damage equipment and impair electrical circuitry, which can result in intermittent or complete failure of your equipment.

Always follow ESD-prevention procedures when removing and replacing components. Ensure that the chassis is electrically connected to an earth ground. Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact. Connect the grounding clip to an unpainted surface of the chassis frame to safely ground ESD voltages. To properly guard against ESD damage and shocks, the wrist strap and cord must operate effectively. If no wrist strap is available, ground yourself by touching the metal part of the chassis.

For safety, periodically check the resistance value of the antistatic strap, which should be between one and 10 megohms.

See Hardware Specifications for information about physical specifications.

See Power Supply for more detailed information about the power supply in the chassis.

When installing the chassis, consider the following:

• Check the power at the site before installing the chassis to ensure that it is free of spikes and noise. Install a power conditioner, if necessary, to ensure proper voltages and power levels in the appliance-input voltage.

• Install proper grounding for the site to avoid damage from lightning and power surges.

• The chassis does not have a user-selectable operating range. Refer to the label on the chassis for the correct appliance input-power requirement.

• Several styles of AC-input power supply cords are available for the chassis; make sure that you have the correct style for your site.

• If you are using dual redundant (1+1) power supplies, we recommend that you use independent electrical circuits for each power supply.

• Install an uninterruptible power source for your site, if possible.

See Rack-Mount the Chassis for the rack-mount procedure.

Consider the following when planning a rack configuration:

• If you are mounting a chassis in an open rack, make sure that the rack frame does not block the intake or exhaust ports.

• Be sure enclosed racks have adequate ventilation. Make sure that the rack is not overly congested as each chassis generates heat. An enclosed rack should have louvered sides and a fan to provide cooling air.

• In an enclosed rack with a ventilation fan in the top, heat generated by equipment near the bottom of the rack can be drawn upward and into the intake ports of the equipment above it in the rack. Ensure that you provide adequate ventilation for equipment at the bottom of the rack.

• Baffles can help to isolate exhaust air from intake air, which also helps to draw cooling air through the chassis. The best placement of the baffles depends on the airflow patterns in the rack. Experiment with different arrangements to position the baffles effectively.