Alarm Profiling

The router software can monitor the status of the chassis, card or interface module, and ports. It generates alarm messages that are based on the alarm conditions set. To save time and effort, you can change the alarm severity in the alarm configuration using the alarm profiling feature.

The alarm profiling feature enables you to create a unique alarm profile for chassis, card or interface module, and port. Each alarm profile, for example, the chassis alarm profile, is defined with an alarm name. Each alarm profile is classified based on controller types. For each controller type, there is a set of alarms defined with a default severity. You can overwrite the default severity using the alarm profile and suppress the syslog facility based on their preferences. By default, the syslog facility is enabled for an alarm profile.

You can also enable Auto In Service (AINS) through the Alarm Profile. By default, AINS is not enabled for an alarm profile. You must configure it using the ains command.

To configure alarm profiles, create profiles for either chassis, card, or port, then define severities for each alarm, and finally, attach the profile at the corresponding chassis, card, or port.

The highest precedence is maintained at the port level and the lowest precedence is maintained at the chassis level. For example, if the chassis profile is already attached and if you want to have a separate profile for a port, you can still create a port profile and attach it to that port. The port inherits the properties of the port profile.

After the alarm profile is attached, these behaviors are shown about the entity:

  • Chassis alarm profile—When a chassis alarm profile is attached, by default, the profile is attached to all the interface modules available in the chassis. All these interfaces configured under the chassis are applied with the new alarm severity and AINS.

  • Card alarm profile—When a card profile is attached, by default, the profile, along with AINS is attached to all ports that are enabled on the interface module.

  • Port alarm profile—When a port profile is attached, the profile, along with the AINS is applied only to that port.


Note

Card and port alarm profiles with the same name can be attached to multiple cards and ports, respectively.

The alarm profile attached to the chassis, card or interface module, and port can be detached, if the profile is no longer required. Before deleting the alarm profile, ensure that you detach the alarm profile from entity; for example, card or port.

To log the alarms, you need to enable the logging alarm [critical | major | minor | informational] command at the global configuration mode. Only then are the alarms that are configured for the alarm profile are system logged.

For example, if you have enabled the logging alarm using the logging alarm critical command, then for the alarm profile, the alarms with critical severity get system logged only when the syslog is enabled in the alarm profile.


Note

  • If a port is created on the subslot after configuring the alarm profile, that port starts with default secondary admin state as "auto-in-service". The port moves to "in-service" secondary admin state after completing the default soak-timer.

  • If ports are already created before the alarm profile is enabled, the ports move to "in-service" secondary admin state.

Limitations of Alarm Profiles

  • The alarm profile name must not exceed 32 characters.

  • For various alarms, the alarm profiles are not supported for service affecting and non-service affecting classification.

  • For various alarms, the alarm severities such as "Not Reported" and "Not Alarmed" are not supported.

  • The alarm profile created for chassis, card, or port should be attached to the respective entity. the attaching of the alarm profile of one entity to another entity is not supported. For example, the card alarm profile cannot be attached to the chassis alarm profile, or vice versa.

  • The attaching of alarm profile to entities such as, PSU, FAN, and RSP is not supported.

  • AINS States is not supported on the PSU, FAN, and RSP in Cisco IOS XE Release 16.6.1vS.

  • Maximum of one hundred alarm profiles can be created for the system or node (chassis).

  • When a port having line alarm such as SLOS, SLOF, LAIS, and LRDI is shutdown, then after performing the no shutdown operation, the show facility-alarm status does not display the asserted line alarm. Only LINK DOWN alarm is displayed.

  • Clearing an alarm requires more than 10 seconds.

Alarm Profile Classification

Alarm Profile Types

The chassis, card or interface module, and port alarm profiles are classified based on the controller type.

Controller types supported for each alarm profile:

  • 48 X T1/E1 CEM Interface Module

  • 48 X T3/E3 CEM Interface Module

  • 1 x OC-192 Interface module or 8-port Low Rate Interface Module

  • 8-port 10 Gigabit Ethernet Interface Module (8X10GE)

  • 2-port 40 Gigabit Ethernet QSFP Interface Module (2X40GE)

  • 1-port 100 Gigabit Ethernet Interface Module (1X100GE)

  • SFP Combo IM-8-port Gigabit Ethernet (8X1GE) + 1-port 10 Gigabit Ethernet Interface Module (1X10GE)

  • 8/16-port 1 Gigabit Ethernet (SFP/SFP) + 1-port 10 Gigabit Ethernet (SFP+) / 2-port 1 Gigabit Ethernet (CSFP) Interface Module

Alarm Severity

Alarms are filtered based on the severity level. Depending on a requirement, you can override the default severity to a new severity.

The following are severity of alarms supported for each alarm profile associated with the controller type:

  • critical

  • major

  • minor

  • informational

Alarm Profiling Hierarchy

Based on the alarm profile applied to the chassis, card or interface module, or port, the corresponding alarms and their severity levels are applied in the following order of priority:

Table 1. Alarm Profile with Alarm Priority

Alarm Profile

Alarm Priority

port profile

1

card profile

2

chassis profile

3

Behavior of the "ains" Command

  • If a port is provisioned on the card after attaching the alarm profile, that port starts with default secondary admin state as "auto-in-service". The port moves to "in-service" secondary admin state after completing the default soak-timer.

  • If ports are already provisioned before the alarm profile is attached, the ports move to "in-service" secondary admin state.


Note

The secondary admin state cannot be configured unless the alarm profile is configured.

When AINS is enabled on a port, one of the following events takes place:

  • Event-1—If there is an alarm on the port, soaking timer does not start. Existing alarms are displayed in the output of the show facility-conditions status command.

  • Event-2—If there is no alarm on the port, soaking timer is started, and after 15 minutes, the port is displayed in "in-service" state.


    Note

    Default AINS soak time is 8 hours, and it is configurable to a value from 15 minutes to 48 hours, with steps of 15 minutes

    Before the soaking timer expires, alarms are considered as conditions and displayed in the output of the show facility-conditions status command.

    After the soaking timer expires, any further alarms on that port are displayed in the output the show facility-alarms status command.

For example, at time T1, an alarm is present on a port, Event-1 applies. If after an hour, the alarm is cleared, then Event-2 applies.

How to Configure Alarm Profile

This section provides information about configuring alarm profile for chassis, card, or port.

Creating Alarm Profile

You can create an alarm profile for chassis, card or interface module, and port. The alarm profile name should be a string with alpha numeric characters. The alarm profile is associated with an alarm with controller types such as T1 or E1. You can suppress syslog and provide a new severity for the alarm.


Note

Before including syslog for the alarm, ensure that you enable the logging alarm command at the global level. To enable the logging alarms, use the logging alarm [critical | major | minor | informational] command.


Note

You cannot provide the same profile name for chassis, card, or port.

Creating Alarm Profile for Chassis

To create the alarm profile CHASSIS, use the following commands: 

router(config)#alarm profile CHASSIS chassis 
router(config-alarm-profile)#alarm ds1
router(config-alarm-properties)#DS1_LOS suppress
router(config-alarm-properties)#DS1_LOS severity critical
router(config-alarm-properties)# ains

The command ains enables Auto In-Service (AINS) on the chassis.


Note

When the alarm profile is attached to the chassis, all cards and ports on the chassis inherit the severity from the chassis profile.

Creating Alarm Profile for Card

To create the alarm profile CARD, use the following commands: 

router(config)#alarm profile CARD card 
router(config-alarm-profile)#alarm ds1
router(config-alarm-properties)#DS1_LOS suppress
router(config-alarm-properties)#DS1_LOS severity major
router(config-alarm-properties)# ains

The command ains enables AINS on the card.


Note

When the alarm profile is attached to a card, all ports on the card inherit the severity from the card profile.

Note

If a chassis profile is already attached and if you want to have a separate profile for a card, you can still create a card profile and attach it to that card. The card and all its ports inherit the properties of the card profile.

Creating Alarm Profile for Port

To create the alarm profile PORT, use the following commands: 

 router(config)#alarm profile PORT port 
router(config-alarm-profile)#alarm ds1
router(config-alarm-properties)#DS1_LOS suppress
router(config-alarm-properties)#DS1_LOS severity major
router(config-alarm-properties)# ains

The command ains enables AINS on the port.


Note

When the alarm profile attached to a port, only the port inherits the severity from the port profile.

Note

If the chassis profile is already attached and if you want to have a separate profile for a port, you can still create a port profile and attach it to that port. The port inherits the properties of the port profile.

Use Case 1

The following example explains default alarm profile having DS1_TX_AIS alarm with severity as MINOR and syslog is enabled, and when the alarm is configured as suppressed with default severity, the alarm is not displayed under the show alarm profile command.

Use the following steps to suppress the default alarm profile:

  1. Create a chassis profile, for example, chassis and verity that the DS1_TX_AIS alarm is listed under the show alarm profile chassis command.

  2. Set the alarm DS1_TX_AIS as suppressed.

The alarm DS1_TX_AIS is not displayed under the show alarm profile chassis command.

Create chassis profile


Router#configure terminal
Router(config)#alarm-profile chassis chassis 
Router(config-alarm-profile)#end
Router#show alarm profile chassis
Alarm profile chassis:
  DS1:
  Alarm Name                                                                                        Severity   Syslog    
  Transmitter is sending AIS                                                                        MINOR       Enabled 
  Receiver has loss of signal                                                                       CRITICAL    Enabled   
  Receiver has loss of frame                                                                        INFO        Enabled   
  Receiver has remote alarm INFO                                                                    INFO        Enabled

Set the alarm DS1_TX_AIS as suppressed


Router(config)#alarm-profile chassis chassis 
Router(config-alarm-profile)#alarm ds1 
Router(config-alarm-properties)#DS1_TX_AIS suppress 
Router(config-alarm-properties)#end

Note that the DS1_TX_AIS alarm is not displayed under the show alarm profile chassis command.

Router#show alarm profile chassis
Alarm profile chassis:
  DS1:
  Alarm Name                                                                                        Severity   Syslog    
  Receiver has loss of signal                                                                       CRITICAL    Enabled   
  Receiver has loss of frame                                                                        INFO        Enabled   
  Receiver has remote alarm                                                                         INFO        Enabled

Use Case 2

The following example displays default profile having DS1_TX_AIS alarm with severity as MINOR and syslog enabled, and when the alarm is configured as suppressed with severity set to INFO, the alarm is displayed under the show alarm profile command.

Use the following steps to change the DS1_TX_AIS alarm severity:

  1. Create a chassis profile, for example, chassis.

  2. Set the alarm DS1_TX_AIS as suppressed and alarm DS1_TX_AIS severity to INFO.

The alarm DS1_TX_AIS is displayed under the show alarm profile chassis command.

Create chassis profile


Router#configure terminal
Router(config)#alarm-profile chassis chassis 
Router(config-alarm-profile)#end

Set the alarm DS1_TX_AIS as suppressed and severity to INFO


Router(config)#alarm-profile chassis chassis 
Router(config-alarm-profile)#alarm ds1 
Router(config-alarm-properties)#DS1_TX_AIS suppress 
Router(config-alarm-properties)#DS1_TX_AIS severity INFO
Router(config-alarm-properties)#end

Note that the DS1_TX_AIS alarm is displayed under the show alarm profile chassis command.

Router#show alarm profile chassis
Alarm profile chassis:
  DS1:
 Alarm Name                                                                                        Severity   Syslog    
 Transmitter is sending AIS                                                                        MINOR       Enabled
 Receiver has loss of signal                                                                       CRITICAL    Enabled   
 Receiver has loss of frame                                                                        INFO        Enabled   
 Receiver has remote alarm                                                                         INFO        Enabled

Use Case 3

The following example displays default profile having DS1_LOF and DS1_RX_RAI alarms with severities as CRITICAL and MINOR respectively. Using the chassis profile, you can set the DS1_LOF alarm severity to INFO and verify using the show alarm profile command. The show output displays the DS1_LOF as INFO and DS1_RX_RAI as MINOR.

Use the following steps to change the DS1_LOF alarm severity:

  1. Create a chassis profile, for example, chassis.

  2. Set the alarm DS1_LOF severity to INFO.

The alarm DS1_LOF is displayed under the show alarm profile chassis command.

Create a chassis profile


Router#configure terminal
Router(config)#alarm-profile chassis chassis 
Router(config-alarm-profile)#end

Set the alarm DS1_LOF severity to INFO


Router(config)#alarm-profile chassis chassis 
Router(config-alarm-profile)#alarm t1 
Router(config-alarm-properties)#DS1_LOF severity INFO 
Router(config-alarm-properties)#end

Note that the DS1_LOF alarm is displayed under the show alarm profile chassis command.


Router#show alarm profile chassis
Alarm profile chassis:
 T1:
  Alarm Name                                                                                        Severity   Syslog    
 Transmitter is sending AIS                                                                        MINOR       Enabled
 Receiver has loss of signal                                                                       CRITICAL    Enabled   
 Receiver has loss of frame                                                                        INFO        Enabled   
 Receiver has remote alarm                                                                         MINOR        Enabled

Use Case 4

The following example displays default profile having DS1_LOF and DS1_RX_RAI alarms with severities as CRITICAL and MINOR respectively. Using the card profile, you can set the DS1_LOF alarm severity to MAJOR and verify using the show alarm profile command. The show output displays the DS1_LOF as MAJOR and DS1_RX_RAI as MINOR.

Use the following steps to change the DS1_LOF alam severity:

  1. Create a card profile, for example, card.

  2. Set the alarm DS1_LOF severity to MAJOR.

The alarm DS1_LOF with severity MAJOR is displayed under the show alarm profile command.

Create a card profile and set the alarm DS1_LOF severity to MAJOR 


Router#configure terminal
Router(config)#alarm-profile card card 
Router(config-alarm-profile)#alarm ds1 
Router(config-alarm-properties)#DS1_LOF severity MAJOR 
Router(config-alarm-properties)#end

Note that the DS1_LOF with severity MAJOR and DS1_RX_RAI with severity MINOR are displayed under the show alarm profile command.


Router#show alarm profile 
Alarm profile card:
 DS1:
Alarm Name                                                                                         Severity   Syslog    
 Transmitter is sending AIS                                                                        MINOR       Enabled
 Receiver has loss of signal                                                                       CRITICAL    Enabled   
 Receiver has loss of frame                                                                        MAJOR        Enabled   
 Receiver has remote alarm                                                                         MINOR        Enabled

Use Case 5

The following example displays default profile having DS1_LOF and DS1_RX_RAI alarms with severities as CRITICAL and MINOR respectively. Using the port profile, you can set the DS1_LOF alarm severity to MAJOR and DS1_RX_RAI alarm severity to INFO. Verify using the show alarm profile command. The show output displays the DS1_LOF as MAJOR and DS1_RX_RAI as INFO.

Use the following steps to change the DS1_LOF and DS1_RX_RAI alarm severities:

  1. Create a port profile, for example, port.

  2. Set the alarm severities DS1_LOF to MAJOR and DS1_RX_RAI to INFO.

The alarm DS1_LOF with severity MAJOR and DS1_RX_RAI with severity INFO are displayed under the show alarm profile command.

Create a port profile and set the alarm severities of DS1_LOF to MAJOR and DS1_RX_RAI to INFO


Router#configure terminal
Router(config)#alarm-profile port port 
Router(config-alarm-profile)#alarm ds1 
Router(config-alarm-properties)#DS1_LOF severity MAJOR 
Router(config-alarm-properties)#DS1_RX_RAI severity MINOR 
Router(config-alarm-properties)#end

Note that the DS1_LOF with severity MAJOR and DS1_RX_RAI with severity INFO are displayed under the show alarm profile command.


Router#show alarm profile 
Alarm profile port:
 DS1:
Alarm Name                                                                                         Severity   Syslog    
 Transmitter is sending AIS                                                                        MINOR       Enabled
 Receiver has loss of signal                                                                       CRITICAL    Enabled   
 Receiver has loss of frame                                                                        MAJOR        Enabled   
 Receiver has remote alarm                                                                         INFO        Enabled

Attaching Alarm Profile to Entity

After the alarm profile is created for chassis, card, or port, you need to attach the alarm profile to chassis, card, or port. Only after attaching the alarm profile, the alarm serverity and other alarm functionalities are applied to the chassis, card, or port.

Attaching Alarm Profile to Chassis

To attach the alarm profile to chassis, use the following commands:

 router>enable
router#configure terminal
router(config)#alarm-profile chassis attach chassis
router(config)#end

Note

When an alarm profile is attached to chassis, the profile is applicable to all the cards available on the node but not to cards that are inserted after the profile attach is performed. To attach alarm profile to cards, you need to reattach the alarm profile to the chassis.

Attaching Alarm Profile to Card

To attach an alarm profile to the card, use the following commands:

 router>enable
router#configure terminal
router(config)#alarm-profile card attach card slot/bay
router(config)#end

Note

The alarm profile cannot be attached to a slot when there is no card available in the slot.

Attaching Alarm Profile to Port

Depending on the controller type, the alarm profile is attached to the port. Supported controller types are T1 and E1. You need to select the controller and the port, and then attach the profile

To attach the alarm profile to port, use the following commands:

 

router>enable
router#configure terminal
router(config)#controller {t1 | e1}  slot/bay/port
router(config-controller)#  attach profile port
router(config-controller)#end

To attach the port profile to Ethernet interface, use the following commands:

 

router>enable
router#configure terminal
router(config)#interface gigabitethernet 0/7/0
router(config-controller)#  attach profile port
router(config-controller)#end

Note

The following restrictions apply to the 8/16-port 1 Gigabit Ethernet (SFP/SFP) + 1-port 10 Gigabit Ethernet (SFP+) / 2-port 1 Gigabit Ethernet (CSFP) Interface Module:

  • Only the following three AINS modes are supported:

    • 8x1G + 1x10G (default mode) Fully Subscribed

    • 16x1G+1x10G – Over Subscribed

    • 18x1G – Over Subscribed

  • If you change any of the above modes, the chassis and card profiles stay unaffected; however, port profile is disabled and requires to be reattached.

Modifying Alarm Profile

You can modify the existing alarm profile associated with chassis, port, or card. The options that you can modify are the alarm severity and suppress syslog facility. The alarm severity that you can modify are critical, major, minor, and informational.

Modifying Chassis Alarm Profile

To modify the existing alarm confugured for chassis, use the follwing commands:

 router(config)#alarm profile CHASSIS chassis 
router(config-alarm-profile)#alarm ds1
router(config-alarm-properties)#DS1_LOS suppress
router(config-alarm-properties)#DS1_LOS severity minor

Modifying Card Alarm Profile

To modify the existing alarm confugured for card, use the follwing commands:

 
router(config)#alarm profile CARD card 
router(config-alarm-profile)#alarm ds1
router(config-alarm-properties)#DS1_LOS suppress
router(config-alarm-properties)#DS1_LOS severity minor

Modifying Port Alarm Profile

To modify the existing alarm confugured for port, use the follwing commands:

 
router(config)#alarm profile PORT port 
router(config-alarm-profile)#alarm ds1
router(config-alarm-properties)#DS1_LOS suppress
router(config-alarm-properties)#DS1_LOS severity minor

Detaching Alarm Profile

You can detach the existing alarm profile from chassis, card, or port and attach a new profile. If a new alarm profile is not attached, then the default profile is attached.

Detaching Alarm Profile from Chassis

When the alarm profile assocaited with chassis is detached, the profile is removed from all the interfaces that are available in the chassis. The alarms configured for the profile have no effect on these interfaces even when alarm conditions occur.

To detach the alarm profile associated with chassis, use the following command:

Router(config)#no alarm-profile attach CHASSIS chassis

Detaching Alarm Profile from Card

For the alarm profile assocaited with card, when detached, the profile is removed from all the ports and the interfaces. While detaching the alarm profile, you need to specify the slot and subslot.

To detach the alarm profile associated with card, use the following command:

Router(config)#no alarm-profile attach CARD 0/3

Detaching Alarm Profile from Port

You need to access specific controller and interface to detach the alarm profile associated with the port. The alarm profile is detached from specific interface for the controller.

To detach the alarm profile associated with port, use the following commands:


router(config)#controller t1 0/4/0
router(config-controller)#no attach profile  port


router(config)#controller e1 0/3/2
router(config-controller)#no attach profile  port

Deleting Alarm Profile


Note

Before deleting the alarm profile, detach the profile from chassis, card, or port. Alarm profiles cannot be deleted when profiles are attached.

If the alarm profile is not required anymore, you can delete the alarm profile.

Deleting Alarm Profile for Chassis

To delete the alarm profile associated with chassis, use the following command:

Router(config)no alarm-profile CHASSIS chassis

Deleting Alarm Profile for Card

To delete the alarm profile associated with card, use the following command:

Router(config)no alarm-profile CARD card

Deleting Alarm Profile for Port

To delete the alarm profile associated with port, use the following command:

Router(config)no alarm-profile PORT port

Verifying Alarm Profile

Use the following commands to verity the alarm profile configuration:

  • show alarm profile—Displays the alarm profile configured for chassis.

  • show facility-alarm status—Displays the alarms status attached to a specific profile.

  • show controller—Displays the alarm profiles configured for a specific port.

  • show logging—Displays the alarms reporting in syslog.

To display the alarm profile configured for chassis, use the show alarm profile command: 

Router# show alarm profile
Alarm profile CHASSIS:
  DS1:
  Alarm Name                           Severity   Syslog    
  Receiver has loss of signal          CRITICAL   Enabled    
  Receiver has loss of frame           INFO       Enabled   
  Receiver has remote alarm            INFO       Enabled

To display the alarm status attached to a specfic profile, use the show alarm profile command: 

Router# show facility-alarm status | inc 0/3/0 
t1 0/3/0  Feb 01 2018 19:23:10  CRITICAL  Section Receiver has loss of signal  [1]

Verifying Alarm Profile for Severity Change for T1 or E1 Alarms

The following example verifies when the severity of the T1 or E1 alarms are modified for a Chassis profile. The alarm severity changes are verified using the show alarm profile command:

Create a CHASSIS alarm profile for the DS1 alarms:

Router(config)#alarm-profile CHASSIS chassis
Router(config-alarm-properties)#alarm ds1
Router(config-alarm-properties)#DS1_LOF severity critical
Router(config-alarm-properties)#DS1_LOF suppress
Router(config-alarm-properties)#alarm ds1
Router(config-alarm-properties)#DS1_RX_RAI severity info
Router(config-alarm-properties)#DS1_RX_RAI suppress

Verify the CHASSIS alarm profile using the show alarm profile command: 

Router#show alarm profile
Alarm profile CHASSIS:
  Alarm Name                                          Severity       Syslog    
  Receiver has loss of signal                         CRITICAL       Enabled   
  Receiver has remote alarm                           MINOR          Enabled

Attach the CHASSIS alarm profile to chassis:

 
router>enable
router#configure terminal
router(config)#alarm-profile CHASSIS attach chassis
router(config)#end

Modify the severity of the CHASSIS alarm profile for the DS1 alarms:


Router(config)#alarm-profile CHASSIS chassis
Router(config-alarm-properties)#alarm ds1
Router(config-alarm-properties)#DS1_LOF severity major
Router(config-alarm-properties)#DS1_LOF suppress
Router(config-alarm-properties)#alarm ds1
Router(config-alarm-properties)#DS1_RX_RAI severity info
Router(config-alarm-properties)#DS1_RX_RAI suppress

Verify the CHASSIS alarm profile with modified severity:

Router#show alarm profile
Alarm profile CHASSIS:
DS1:
  Alarm Name                                          Severity       Syslog    
  Receiver has loss of signal                         MAJOR          Enabled   
  Receiver has remote alarm                           INFO           Enabled

Verifying AINS Alarm Profiles

Verifying AINS Alarm Profile on the Chassis

Router# show running-config | sec alarm-profile

alarm-profile chassis1 chassis
  ains
alarm-profile chassis1 attach chassis
alarm-profile chassis1 attach card 0/0
alarm-profile chassis1 attach card 0/1
alarm-profile chassis1 attach card 0/2
alarm-profile chassis1 attach card 0/3
alarm-profile chassis1 attach card 0/4
alarm-profile chassis1 attach card 0/5
alarm-profile chassis1 attach card 0/6
alarm-profile chassis1 attach card 0/7
alarm-profile chassis1 attach card 0/8
alarm-profile chassis1 attach card 0/9
alarm-profile chassis1 attach card 0/10
alarm-profile chassis1 attach card 0/11
alarm-profile chassis1 attach card 0/12
alarm-profile chassis1 attach card 0/13
alarm-profile chassis1 attach card 0/14
alarm-profile chassis1 attach card 0/15
Router#

Verifying AINS Alarm Profile on the Card

Router# show running-config | sec alarm-profile

alarm-profile card1 card
  ains
alarm-profile card1 attach card 0/7
Router#

Verifying AINS Alarm Profile on the Port

Router# show running-config | sec alarm-profile

alarm-profile port1 port
  ains
Router#show running-config | sec 0/7/0
interface GigabitEthernet0/7/0
 no ip address
 negotiation auto
 secondary-admin-state in-service
 attach profile port1
Router#

Verifying the AINS States on Cards and Ports


Note

AINS States are not supported on the PSU, Fans, and RSP in Cisco IOS XE Release 16.6.1vS.

 

Router# show facility-ains status

Slot   Cfg IM Type         Actual IM Type      Op State           Ad State Op Mode        BW
------ ------------------- ------------------- ------------------ -------- ------------   --
 0/0   -                   -                   Empty              N/A      -
 0/1   -                   -                   Empty              N/A      -
 0/2   -                   -                   Empty              N/A      -
 0/3   -                   NCS4200-48T1E1-CE   IS-NR              IS       -
 0/4   -                   -                   Empty              N/A      -
 0/5   -                   -                   Empty              N/A      -
 0/6   -                   -                   Empty              N/A      -
 0/7   NCS4200-1T16G-PS    NCS4200-1T16G-PS    IS-NR              IS       8x1G+1x10G
 0/8   -                   -                   Empty              N/A      -
 0/9   -                   -                   Empty              N/A      -
 0/10  -                   -                   Empty              N/A      -
 0/11  -                   -                   Empty              N/A      -
 0/12  -                   -                   Empty              N/A      -
 0/13  -                   -                   Empty              N/A      -
 0/14  -                   -                   Empty              N/A      -
 0/15  -                   -                   Empty              N/A      -

IFNAME                        Op State            Ad State            Alarm
------                        ------------------  --------            -----

T1 0/3/0                      IS-NR               in-service          -
T1 0/3/1                      IS-NR               in-service          -
T1 0/3/2                      IS-NR               in-service          -
T1 0/3/3                      IS-NR               in-service          -
T1 0/3/4                      IS-NR               in-service          -
T1 0/3/5                      IS-NR               in-service          -
T1 0/3/6                      IS-NR               in-service          -
T1 0/3/7                      IS-NR               in-service          -
T1 0/3/8                      IS-NR               in-service          -
T1 0/3/9                      IS-NR               in-service          -
T1 0/3/10                     IS-NR               in-service          -
T1 0/3/11                     OOS-AU,AINS & FLT   auto-in-service     -
T1 0/3/12                     IS-NR               in-service          -
T1 0/3/13                     IS-NR               in-service          -
T1 0/3/14                     IS-NR               in-service          -
T1 0/3/15                     OOS-AU,FLT          in-service          -
T1 0/3/16                     OOS-AU,FLT          in-service          -
T1 0/3/17                     IS-NR               in-service          -
T1 0/3/18                     IS-NR               in-service          -
T1 0/3/19                     IS-NR               in-service          -
T1 0/3/20                     IS-NR               in-service          -
T1 0/3/21                     IS-NR               in-service          -
T1 0/3/22                     IS-NR               in-service          -
T1 0/3/23                     IS-NR               in-service          -
T1 0/3/24                     IS-NR               in-service          -
T1 0/3/25                     IS-NR               in-service          -
T1 0/3/26                     IS-NR               in-service          -
T1 0/3/27                     IS-NR               in-service          -
T1 0/3/28                     IS-NR               in-service          -
T1 0/3/29                     IS-NR               in-service          -
T1 0/3/30                     IS-NR               in-service          -
T1 0/3/31                     OOS-AU,FLT          in-service          -
T1 0/3/32                     IS-NR               in-service          -
T1 0/3/33                     IS-NR               in-service          -
T1 0/3/34                     IS-NR               in-service          -
T1 0/3/35                     IS-NR               in-service          -
T1 0/3/36                     IS-NR               in-service          -
T1 0/3/37                     IS-NR               in-service          -
T1 0/3/38                     IS-NR               in-service          -
T1 0/3/39                     IS-NR               in-service          -
T1 0/3/40                     IS-NR               in-service          -
T1 0/3/41                     IS-NR               in-service          -
T1 0/3/42                     IS-NR               in-service          -
T1 0/3/43                     IS-NR               in-service          -
T1 0/3/44                     IS-NR               in-service          -
T1 0/3/45                     OOS-AU,FLT          in-service          -
T1 0/3/46                     OOS-AU,FLT          in-service          -
T1 0/3/47                     IS-NR               in-service          -
GigabitEthernet0/7/0          IS-NR               in-service          -
GigabitEthernet0/7/2          IS-NR               in-service          -
GigabitEthernet0/7/4          OOS-AU,FLT          in-service          -
GigabitEthernet0/7/6          OOS-AU,FLT          in-service          -
GigabitEthernet0/7/8          OOS-AU,FLT          in-service          -
GigabitEthernet0/7/10         OOS-AU,FLT          in-service          -
GigabitEthernet0/7/12         OOS-AU,FLT          in-service          -
GigabitEthernet0/7/14         OOS-AU,FLT          in-service          -
TenGigabitEthernet0/7/16      OOS-AU,FLT          in-service          -

Verifying Alarms on the Chassis

This command displays all system alarms.

Router# show facility-alarm status

System Totals  Critical: 11  Major: 11  Minor: 1

Source                     Time                   Severity      Syslog String                  Description [Index]
------                     ------                 --------      -------------                  -------------------
Power Supply Bay 0         Mar 21 2018 08:15:39   CRITICAL      PSU_MISSING                    Power Supply/FAN Module Missing [0]
Power Supply Bay 1         Mar 21 2018 08:15:39   CRITICAL      PSU_MISSING                    Power Supply/FAN Module Missing [0]
T1 0/3/15                  Mar 21 2018 08:17:16   MAJOR         DS1_LINK_DOWN                  Ds1 Physical Port Link Down [12]
T1 0/3/16                  Mar 21 2018 08:17:16   MAJOR         DS1_LINK_DOWN                  Ds1 Physical Port Link Down [12]
T1 0/3/31                  Mar 21 2018 08:17:16   MAJOR         DS1_LINK_DOWN                  Ds1 Physical Port Link Down [12]
T1 0/3/45                  Mar 21 2018 08:17:16   MAJOR         DS1_LINK_DOWN                  Ds1 Physical Port Link Down [12]
T1 0/3/46                  Mar 21 2018 08:17:31   MINOR         DS1_RAI                        Receiver has remote alarm [8]
T1 0/3/46                  Mar 21 2018 08:17:16   MAJOR         DS1_LINK_DOWN                  Ds1 Physical Port Link Down [12]
xcvr container 0/7/4       Mar 21 2018 08:16:47   CRITICAL      XCVR_MISSING_LINK_DOWN         Transceiver Missing - Link Down [1]
xcvr container 0/7/6       Mar 21 2018 08:16:47   CRITICAL      XCVR_MISSING_LINK_DOWN         Transceiver Missing - Link Down [1]
xcvr container 0/7/8       Mar 21 2018 08:16:47   CRITICAL      XCVR_MISSING_LINK_DOWN         Transceiver Missing - Link Down [1]
xcvr container 0/7/10      Mar 21 2018 08:16:47   CRITICAL      XCVR_MISSING_LINK_DOWN         Transceiver Missing - Link Down [1]
xcvr container 0/7/12      Mar 21 2018 08:16:47   CRITICAL      XCVR_MISSING_LINK_DOWN         Transceiver Missing - Link Down [1]
xcvr container 0/7/14      Mar 21 2018 08:16:47   CRITICAL      XCVR_MISSING_LINK_DOWN         Transceiver Missing - Link Down [1]
xcvr container 0/7/16      Mar 21 2018 08:16:47   CRITICAL      XCVR_MISSING_LINK_DOWN         Transceiver Missing - Link Down [1]

Displaying Alarm Conditions on the Chassis

This command displays all port alarms.

Router# show facility-condition status

Source                     Time                   Severity      Syslog String                  Description [Index]
------                     ------                 --------      -------------                  -------------------
T1 0/3/11                  Mar 21 2018 08:17:16   MAJOR         DS1_LINK_DOWN                  Ds1 Physical Port Link Down [12]