Cisco ASR 9000 Series Aggregation Services Router Multicast Command Reference, Release 5.1.x
Bias-Free Language
The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
- Updated:
- December 12, 2017
Chapter: Multicast Routing and Forwarding Commands
- accounting per-prefix
- accounting per-prefix forward-only
- address-family (multicast)
- boundary
- clear mfib counter
- clear mfib database
- clear mfib hardware resource-counters
- clear mfib hardware route statistics
- disable (multicast)
- enable (multicast)
- forwarding-latency
- interface (multicast)
- interface all enable
- interface-inheritance disable
- log-traps
- maximum disable
- mdt c-multicast-routing
- mdt data
- mdt data ingress replication
- mdt default
- mdt mtu
- mdt source
- migration route-policy
- multicast-routing
- multipath
- nsf (multicast)
- oom-handling
- rate-per-route
- shared-tree-prune delay
- show mfib bvi
- show mfib connections
- show mfib counter
- show mfib encap-info
- show mfib hardware interface
- show mfib hardware ltrace
- show mfib hardware resource-counters
- show mfib hardware route accept-bitmap
- show mfib hardware route internal
- show mfib hardware route location
- show mfib hardware route mofrr
- show mfib hardware route olist
- show mfib hardware route statistics
- show mfib hardware route summary
- show mfib hardware table
- show mfib interface
- show mfib nsf
- show mfib route
- show mfib table-info
- show mrib client
- show mrib bvi
- show mrib nsf
- show mrib route
- show mrib route-collapse
- show mrib route outgoing-interface
- show mrib table-info
- show mrib tlc
- static-rpf
- source-tree-prune-delay
- suppress-pim-data-signaling
- suppress-shared-tree-join
- ttl-threshold (multicast)
- unicast-reachability
- vrf (multicast)
Multicast Routing
and Forwarding Commands
This module describes the commands used to configure and monitor multicast routing.
For detailed information about multicast routing concepts, configuration tasks, and examples, refer to the Implementing Multicast Routing on Cisco IOS XR Software configuration module in the Cisco ASR 9000 Series Aggregation Services Router Multicast Configuration Guide.
- accounting per-prefix
- accounting per-prefix forward-only
- address-family (multicast)
- boundary
- clear mfib counter
- clear mfib database
- clear mfib hardware resource-counters
- clear mfib hardware route statistics
- disable (multicast)
- enable (multicast)
- forwarding-latency
- interface (multicast)
- interface all enable
- interface-inheritance disable
- log-traps
- maximum disable
- mdt c-multicast-routing
- mdt data
- mdt data ingress replication
- mdt default
- mdt mtu
- mdt source
- migration route-policy
- multicast-routing
- multipath
- nsf (multicast)
- oom-handling
- rate-per-route
- shared-tree-prune delay
- show mfib bvi
- show mfib connections
- show mfib counter
- show mfib encap-info
- show mfib hardware interface
- show mfib hardware ltrace
- show mfib hardware resource-counters
- show mfib hardware route accept-bitmap
- show mfib hardware route internal
- show mfib hardware route location
- show mfib hardware route mofrr
- show mfib hardware route olist
- show mfib hardware route statistics
- show mfib hardware route summary
- show mfib hardware table
- show mfib interface
- show mfib nsf
- show mfib route
- show mfib table-info
- show mrib client
- show mrib bvi
- show mrib nsf
- show mrib route
- show mrib route-collapse
- show mrib route outgoing-interface
- show mrib table-info
- show mrib tlc
- static-rpf
- source-tree-prune-delay
- suppress-pim-data-signaling
- suppress-shared-tree-join
- ttl-threshold (multicast)
- unicast-reachability
- vrf (multicast)
accounting per-prefix
To enable accounting for multicast routing, use the accounting per-prefix command in the appropriate configuration mode. To return to the default behavior, use the no form of this command.
accounting per-prefix
no accounting per-prefix
Syntax Description
This command has no keywords or arguments.
Command Default
This feature is disabled by default.
Command Modes
Multicast routing configuration
Multicast routing address family IPv4 configuration
Multicast VRF configuration
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The accounting per-prefix command is used to enable per-prefix counters only in hardware. Cisco IOS XR Software counters are always present. When enabled, every existing and new (S, G) route is assigned forward, punt, and drop counters on the ingress route and forward and punt counters on the egress route. The (*, G) routes are assigned a single counter.
There are a limited number of counters on all nodes. When a command is enabled, counters are assigned to routes only if they are available.
To display packet statistics, use the show mfib route and the show mfib hardware route statistics commands. These commands display “N/A” for counters when no hardware statistics are available or whenthe accounting per-prefix command is disabled .
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write |
Examples
The following example shows how to enable accounting for multicast routing:
RP/0/RSP0/CPU0:router(config)# multicast-routing RP/0/RSP0/CPU0:router(config-mcast)# accounting per-prefix
Related Commands
Command | Description |
| Displays platform-specific Multicast Forwarding Information Base (MFIB) information for the packet and byte counters for each route. |
| Displays route entries in the Multicast Forwarding Information Base (MFIB). |
accounting per-prefix forward-only
To reduce hardware statistics resource allocations when enabling accounting, particularly for multicast VPN (MVPN), use the accounting per-prefix forward-only command under multicast routing configuration mode. To return to the default mode of accounting per-prefix, use the no form of this command.
accounting per-prefix forward-only
no accounting per-prefix forward-only
Syntax Description
This command has no keywords or arguments.
Command Default
If no counters were configured, there is no default.
If the accounting per-prefix counter was previously configured, it becomes the default.
If no accounting was configured for multicast routing, forwarding-only is the default mode and triggers a data MDT transition in the case of MVPN deployment.
Command Modes
Multicast routing configuration
Multicast routing address family IPv4 and IPv6 configuration
Multicast VRF configuration
Command History
|
Release |
Modification |
|---|---|
|
Release 3.8.0 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
 Note | The accounting per-prefix forward-only command has only one fwd-only counter. In other words, there is no punt or drop counter allocated. |
We recommended this command for configuration of multicast VPN routing or for any line card that has a route-intensive configuration. Each individual router can support up to 150,000 routes.
Note | To verify the number of statistics allocated or free on a line card, use the show mfib hardware resource-counters command in EXEC mode. |
There are a limited number of counters on all nodes. When accounting on a prefix is enabled, counters are assigned to routes only if they are available.
To display packet statistics, use the show mfib route and the show mfib hardware route statistics commands. These commands display “N/A” for counters when no hardware statistics are available or when neither the accounting per-prefix command nor the accounting per-prefix forward-only command are enabled.
You may switch between accounting-perprefix and accounting per-prefix forward-only statistics for ipv4 or ipv6 multicast family. However, be aware that only one set of counters is supported on the (*,G) routes (with fwd/punt/drop on ingress and fwd/drop on egress) regardless of whether you enabled the accounting-perprefix or accounting-perprefix fwd-only command.
Although you can switch accounting modes, this involves freeing the hardware statistics and reallocating them, thereby resulting in a loss of any previously collected data. Therefore, it is preferable to decide which statistics mode you want to use at the start to avoid the resource cost entailed by resetting the statistics counter values with a change in mode.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write |
Examples
The following example shows how to enable accounting per-prefix forward-only for MVPN routing:
RP/0/RSP0/CPU0:router(config)# multicast-routing RP/0/RSP0/CPU0:router(config-mcast)# accounting per-prefix forward-only
Related Commands
Command | Description |
| Enables accounting for multicast routing. |
| Clears global resource counters. |
address-family (multicast)
To display available IP prefixes to enable multicast routing and forwarding on all router interfaces, use the address-family command in multicast-routing configuration mode or multicast VRF configuration submode. To disable use of an IP address prefix for routing, use the no form of this command.
address-family [ vrf vrf-name ] { ipv4 | ipv6 }
no address-family [ vrf vrf-name ] { ipv4 | ipv6 }
Syntax Description
|
vrf vrf-name |
(Optional) Specifies a VPN routing and forwarding (VRF) instance. |
|
ipv4 |
Specifies IPv4 address prefixes. |
|
ipv6 |
Specifies IPv6 address prefixes. |
Command Default
No default behavior or values
Command Modes
Multicast routing configuration
Multicast VRF configuration
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
|
Release 4.2.0 |
The ipv6 keyword was added. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the address-family command either from multicast routing configuration mode or from multicast VRF configuration sub to enter either the multicast IPv4 or IPv6 address family configuration submode, depending on which keyword was chosen. Use the address-family command with the multicast-routing command to start the following multicast processes:
- Multicast Routing Information Base (MRIB)
- Multicast Forwarding Engine (MFWD)
- Protocol Independent Multicast Sparse mode (PIM-SM)
- Internet Group Management Protocol (IGMP)
- Multicast Listener Discovery Protocol (MLD)
Basic multicast services start automatically when the multicast PIE is installed, without any explicit configuration required. The following multicast services are started automatically:
- Multicast Routing Information Base (MRIB)
- Multicast Forwarding Engine (MFWD)
- Protocol Independent Multicast Sparse mode (PIM-SM)
- Internet Group Management Protocol (IGMP)
Other multicast services require explicit configuration before they start. For example, to start the Multicast Source Discovery Protocol (MSDP) process, you must enter the router msdp command and explicitly configure it.
To enable multicast routing and protocols on interfaces, you must explicitly enable the interfaces using the interface command in multicast routing configuration mode. This action can be performed on individual interfaces or by configuring a wildcard interface using the alias command.
To enable multicast routing on all interfaces, use the interface all enable command in multicast routing configuration mode. For any interface to be fully enabled for multicast routing, it must be enabled specifically (or configured through the interface all enable command for all interfaces) in multicast routing configuration mode, and it must not be disabled in the PIM and IGMP configuration modes.
Note | The enable and disable keywords available under the IGMP and PIM interface configuration modes have no effect unless the interface is enabled in multicast routing configuration mode—either by default or by explicit interface configuration. |
To allow multicast forwarding functionality, while turning multicast routing functionality off, interface-inheritance disable command on a per interface or interface all enable basis in PIM or IGMP configuration mode.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write |
Examples
This example shows how to enter IPv4 and IPv6 multicast routing configuration mode:
RP/0/RSP0/CPU0:router(config)# multicast-routing RP/0/RSP0/CPU0:router(config-mcast)# address-family ipv4 RP/0/RSP0/CPU0:router(config-mcast-default-ipv4)# RP/0/RSP0/CPU0:router(config-mcast)# address-family ipv6 RP/0/RSP0/CPU0:router(config-mcast-default-ipv6)#
This example shows how to enter IPv4 and IPv6 VRF multicast routing configuration submode:
RP/0/RSP0/CPU0:router(config)# multicast-routing RP/0/RSP0/CPU0:router(config-mcast)# vrf vrf-name address-family ipv4 RP/0/RSP0/CPU0:router(config-mcast-vrf-name-ipv4)# RP/0/RSP0/CPU0:router(config-mcast)# vrf vrf-name address-family ipv6 RP/0/RSP0/CPU0:router(config-mcast-vrf-name-ipv6)#-
Related Commands
|
Command |
Description |
|---|---|
|
alias |
Creates a command alias. |
|
Enables multicast routing and forwarding on all new and existing interfaces. |
|
|
interface all disable |
Disables PIM processing on all new and existing interfaces. |
|
Separates the disabling of multicast routing and forwarding. |
|
|
Configures multicast interface properties. |
boundary
To configure the multicast boundary on an interface for administratively scoped multicast addresses, use the boundary command in the appropriate configuration mode. To return to the default behavior, use the no form of this command.
boundary access-list
no boundary access-list
Syntax Description
|
access-list |
Access list specifying scoped multicast groups. The name cannot contain a space or quotation mark; it may contain numbers. |
Command Default
A multicast boundary is not configured.
Command Modes
Multicast routing interface configuration
Multicast routing VRF interface configuration
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
The boundary command is used to set up a boundary to keep multicast packets from being forwarded.
The boundary acl can specify a mcast source address in addition to a mcast group address. The keyword "any" can be added before the mcast group range.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write |
Examples
The following example shows how to set up a boundary for all administratively scoped addresses:
RP/0/RSP0/CPU0:router(config) # ipv4 access-list myboundary2 RP/0/RSP0/CPU0:router (config) # 10 deny ipv4 any 239.0.0.0 0.255.255.255 RP/0/RSP0/CPU0:router(config) # 20 permit ipv4 any 224.0.0.0 15.255.255.255 RP/0/RSP0/CPU0:router(config)# multicast-routing RP/0/RSP0/CPU0:router (config-mcast) # address-family ipv4 RP/0/RSP0/CPU0:router(config-mcast-default-ipv4)# interface GigE 0/2/0/2 RP/0/RSP0/CPU0:router(config-mcast-default-ipv4-if)# boundary myboundary2
clear mfib counter
To clear Multicast Forwarding Information Base (MFIB) route packet counters, use the clear mfib counter command in the appropriate mode.
clear mfib [ vrf vrf-name ] ipv4 counter [ group-address | source-address ] [ location { node-id | all } ]
Syntax Description
|
vrf vrf-name |
(Optional) Specifies a VPN routing and forwarding (VRF) instance. |
|
ipv4 |
(Optional) Specifies IPv4 address prefixes. |
|
group-address |
(Optional) IP address of the multicast group. |
|
source-address |
(Optional) IP address of the source of the multicast route. |
|
location node-id |
(Optional) Clears route packet counters from the designated node. |
|
all |
The all keyword clears route packet counters on all nodes |
Command Default
IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Note | This command only clears MFIB route packet software counters. To clear MFIB hardware statistics counters use the clear mfib hardware route statistics command. |
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write |
Examples
The following example shows how to clear MFIB route packet counters on all nodes:
RP/0/RSP0/CPU0:router# clear mfib counter location all
clear mfib database
To clear the Multicast Forwarding Information Base (MFIB) database, use the clear mfib database command in the appropriate mode.
clear mfib [ ipv4 | ipv6 ] database [ location { node-id | all } ]
Syntax Description
|
ipv4 |
(Optional) Specifies IPv4 address prefixes. |
|
location node-id |
(Optional) Clears global resource counters from the designated node. |
|
all |
The all keyword clears all global resource counters. |
Command Default
IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write, execute |
Examples
The following example shows how to clear the Multicast Forwarding Information Base (MFIB) database on all nodes:
RP/0/RSP0/CPU0:router# clear mfib database location all
clear mfib hardware resource-counters
To clear global resource counters, use the clear mfib hardware resource-counters command in EXEC mode.
clear mfib [ vrf vrf-name ] [ ipv4 | ipv6 ] hardware resource-counters [ location { node-id | all } ]
Syntax Description
|
vrf vrf-name |
(Optional) Specifies a VPN routing and forwarding (VRF) instance. |
|
ipv4 |
(Optional) Specifies IPv4 address prefixes. |
|
ipv6 |
(Optional) Specifies IPv6 address prefixes. |
|
location node-id |
(Optional) Clears global resource counters from the designated node. |
|
all |
The all keyword clears all global resource counters. |
Command Default
IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the clear mfib hardware resource-counters to estimate resource usage for an operation.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write, execute |
Examples
The following example shows how to clear all global resource counters:
RP/0/RSP0/CPU0:router# clear mfib hardware resource-counters location all
Related Commands
Command | Description |
| Displays the allocated and freed hardware resources for the Multicast Forwarding Information Base (MFIB) process. |
clear mfib hardware route statistics
To reset all allocated counter values regardless of the Multicast Forwarding Information Base (MFIB) hardware statistics mode (accounting per-prefix or accounting per-prefix forward-only), use the clear mfib hardware route statistics command in EXEC mode.
clear mfib [ vrf vrf-name ] [ ipv4 | ipv6 ] hardware route statistics { egress | ingress | ingress-and-egress } [ * | source-address ] [ group-address [ /prefix-length ] ] [ location { node-id | all } ]
Syntax Description
|
vrf vrf-name |
(Optional) Specifies a VPN routing and forwarding (VRF) instance. |
|
ipv4 |
(Optional) Specifies IPv4 address prefixes. |
|
ipv6 |
(Optional) Specifies IPv6 address prefixes. |
|
ingress-and-egress |
(Optional) Clears hardware statistics on both the incoming (ingress) and outgoing (egress) routes. |
|
* |
(Optional) Clears shared tree route statistics. |
|
source-address |
(Optional) IP address or hostname of the multicast route source. |
|
group-address |
(Optional) IP address or hostname of the multicast group. |
|
/ prefix-length |
(Optional) Prefix length of the multicast group. A decimal value that indicates how many of the high-order contiguous bits of the address compose the prefix (the network portion of the address). A slash must precede the decimal value. |
|
location |
(Optional) Clears route packet counters from the designated node. |
|
node-id |
The node-id argument is entered in the rack/slot/module notation. |
|
all |
The all keyword clears route packet counters on all nodes |
Command Default
If not specified, IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs.
The Multicast Forwarding (MFWD) process exists on each line card and assigns hardware counters to each (S, G) route. Additionally, one global counter is assigned for all (*, G) routes, depending on resource availability.
To clear the set of counters for (*, G) routes, the MFWD process assigns a single set of counters to count packets that match (*, G) routes. Consequently, the clear mfib hardware route statistics command must be used in a form that either clears counters on all routes or matches all (*, G) routes.
Note | This command only clears MFIB hardware statistics counters. To clear MFIB route packet software counters, use the clear mfib counter command. |
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write, execute |
Examples
The following command shows how to clear counters by route statistics for all multicast routes on both ingress and egress forwarding engines for the line card 0/1/CPU0:
RP/0/RSP0/CPU0:router# clear mfib ipv4 hardware route statistics ingress-and-egress location 0/1/CPU0
Related Commands
Command | Description |
| Displays platform-specific Multicast Forwarding Information Base (MFIB) information for the packet and byte counters for each route. |
disable (multicast)
To disable multicast routing and forwarding on an interface, use the disable command in the appropriate configuration mode. To return to the default behavior, use the no form of this command.
disable
no disable
Syntax Description
This command has no keywords or arguments.
Command Default
Multicast routing and forwarding settings are inherited from the global interface enable all command. Otherwise, multicast routing and forwarding is disabled.
Command Modes
Multicast routing interface configuration
Multicast routing VRF interface configuration
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The disable command modifies the behavior of a specific interface to disabled. This command is useful if you want to disable multicast routing on specific interfaces, but leave it enabled on all remaining interfaces.
The following guidelines apply when the enable and disable commands (and the no forms) are used in conjunction with the interface all enable command:
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write |
Examples
The following example shows how to enable multicast routing on all interfaces and disable the feature only on GigabitEthernet interface 0/1/0/0:
RP/0/RSP0/CPU0:router(config)# multicast-routing RP/0/RSP0/CPU0:router(config-mcast)# interface all enable RP/0/RSP0/CPU0:router(config-mcast-default-ipv4)# interface GigE 0/1/0/0 RP/0/RSP0/CPU0:router(config-mcast-default-ipv4-if)# disable
Related Commands
Command | Description |
| Enables multicast routing and forwarding on an interface. |
| Enables multicast routing and forwarding on all new and existing interfaces. |
enable (multicast)
To enable multicast routing and forwarding on an interface, use the enable command in the appropriate configuration mode. To return to the default behavior, use the no form of this command.
enable
no enable
Syntax Description
This command has no keywords or arguments.
Command Default
Multicast routing and forwarding settings are inherited from the global interface enable all command. Otherwise, multicast routing and forwarding is disabled.
Command Modes
Multicast routing interface configuration
Multicast routing VRF interface configuration
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The enable command modifies the behavior of a specific interface to enabled. This command is useful if you want to enable multicast routing on specific interfaces, but leave it disabled on all remaining interfaces.
The following guidelines apply when the enable and disable commands (and the no forms) are used in conjunction with the interface all enable command:
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write |
Examples
The following example shows how to enable multicast routing on a specific interface only:
RP/0/RSP0/CPU0:router(config)# multicast-routing RP/0/RSP0/CPU0:router(config-mcast)# interface GigE 0/1/0/0 RP/0/RSP0/CPU0:router(config-mcast-default-ipv4-if)# enable
Related Commands
Command | Description |
| Disables multicast routing and forwarding on an interface. |
| Enables multicast routing and forwarding on all new and existing interfaces. |
forwarding-latency
To delay traffic being forwarded on a route, use the forwarding-latency command. To return to the default behavior, use the no form of this command.
forwarding-latency [ delay milliseconds ]
no forwarding-latency
Syntax Description
|
delay milliseconds |
(Optional) Specifies the delay time in miliseconds. Range is 5 - 500. |
Command Default
The default delay time is 30 milliseconds.
Command Modes
Multicast routing configuration
IPv4 and IPv6 multicast routing configuration
Command History
|
Release |
Modification |
|---|---|
|
Release 3.8.0 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the forwarding-latency command when you expect a receiver to leave and rejoin the same multicast group within a very short period such as 20 or 30 milliseconds. The delay may be required to provide the router sufficient time to update its Multicast Forwarding Information Base (MFIB) table.
When the forwarding-latency command is enabled, each interface is allocated a separate table lookup unit (TLU) block in the output interface list (olist), thereby increasing TLU hardware resource usage, and, for this reason, it should be used with caution when many multicast routes are present.
When the forwarding-latency command is disabled, up to three interfaces may share a single TLU block in the olist.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write |
Examples
The following example shows how to delay traffic from being forwarded for 120 milliseconds:
RP/0/RSP0/CPU0:router# configure RP/0/RSP0/CPU0:router(config)# multicast-routing RP/0/RSP0/CPU0:router# forwarding-latency delay 120
interface (multicast)
To configure multicast interface properties, use the interface command in the appropriate configuration mode. To disable multicast routing for interfaces, use the no form of this command.
interface type interface-path-id
no interface type interface-path-id
Syntax Description
|
type |
Interface type. For more information, use the question mark (?) online help function. |
||
|
interface-path-id |
Physical interface or virtual interface.
For more information about the syntax for the router, use the question mark ( ? ) online help function. |
Command Default
No default behavior or values
Command Modes
Multicast routing configuration
IPv4 or multicast routing configuration
Multicast VRF configuration
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the interface command to configure multicast routing properties for specific interfaces.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write |
Examples
The following example shows how to enable multicast routing on all interfaces and disable the feature only on GigabitEthernet interface 0/1/0/0:
RP/0/RSP0/CPU0:router(config)# multicast-routing RP/0/RSP0/CPU0:router(config-mcast)# interface all enable RP/0/RSP0/CPU0:router(config-mcast-default-ipv4-if)# interface GigE 0/1/0/0 RP/0/RSP0/CPU0:router(config-mcast-default-ipv4-if)# disable
Related Commands
Command | Description |
| Disables multicast routing and forwarding on an interface. |
| Enables multicast routing and forwarding on an interface. |
| Enables multicast routing and forwarding on all new and existing interfaces. |
interface all enable
To enable multicast routing and forwarding on all new and existing interfaces, use the interface all enable command in the appropriate configuration mode. To return to the default behavior, use the no form of this command.
interface all enable
no interface all enable
Syntax Description
This command has no keywords or arguments.
Command Default
Multicast routing and forwarding is disabled by default.
Command Modes
Multicast routing configuration
Multicast VRF configuration
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
This command modifies the default behavior for all new and existing interfaces to enabled unless overridden by the enable or disable keywords available in interface configuration mode.
The following guidelines apply when the enable and disable commands (and the no forms) are used in conjunction with the interface all enable command:
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write |
Examples
The following example shows how to enable multicast routing on all interfaces and disable the feature only on GigabitEthernet interface 0/1/0/0:
RP/0/RSP0/CPU0:router(config)# multicast-routing RP/0/RSP0/CPU0:router(config-mcast)# interface all enable RP/0/RSP0/CPU0:router(config-mcast)# interface GigE 0/1/0/0 RP/0/RSP0/CPU0:router(config-mcast-default-ipv4-if)# disable
Related Commands
Command | Description |
| Disables multicast routing and forwarding on an interface. |
| Enables multicast routing and forwarding on an interface. |
interface-inheritance disable
To separate PIM and IGMP routing from multicast forwarding on all interfaces, use the interface-inheritance disable command under multicast routing address-family IPv4 submode. To restore the default functionality, use the no form of the command.
interface-inheritance disable
no interface-inheritance disable
Syntax Description
This command has no keywords or arguments.
Command Default
This feature is not enabled by default.
Command Modes
Multicast routing configuration
Address- family IPv4 configuration
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use of the interface-inheritance disable command together with the interface type interface-path-id or interface all enable command under multicast routing address-family IPv4 submode separates PIM and IGMP routing functionality from multicast forwarding on specified interfaces. You can nonetheless enable multicast routing functionality explicitly under PIM or IGMP routing configuration mode for individual interfaces.
Note | Although you can explicitly configure multicast routing functionality on individual interfaces, you cannot explicitly disable the functionality. You can only disable the functionality on all interfaces. |
Used from the address-family ipv4 configuration submode, it prevents IGMP and PIM from inheriting the multicast-routing interface configuration.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write |
Examples
The following configuration disables PIM and IGMP routing functionality on all the interfaces using the interface-inheritance disable command, but multicast forwarding is still enabled on all the interfaces in the example, based on use of the keywords interface all enable .
PIM is enabled on Loopback 0 based on its explicit configuration ( interface Loopback0 enable ) under router pim configuration mode.
IGMP protocol is enabled on GigabitEthernet0/6/0/3, because it too has been configured explicitly under router igmp configuration mode ( interface GigabitEthernet0/6/0/3 router enable ):
RP/0/RSP0/CPU0:router(config)# multicast-routing RP/0/RSP0/CPU0:router(config-mcast)# address-family ipv4 RP/0/RSP0/CPU0:router(config-mcast-default-ipv4)# interface-inheritance disable RP/0/RSP0/CPU0:router(config-mcast-default-ipv4)# interface loopback 1 enable RP/0/RSP0/CPU0:router(config-mcast-default-ipv4)# show run router pim
With the interface-inheritance disable command in use, IGMPand PIM configuration are enabled in the protocol configuration as follows:
router igmp
interface loopback 0
router enable
router pim
interface loopback 0
enable
router pim vrf default address-family ipv4
interface Loopback0
enable
RP/0/RSP0/CPU0:router(config-mcast-default-ipv4)# show run router igmp
router igmp
vrf default
interface GigabitEthernet0/6/0/3
router enable
log-traps
To enable logging of trap events, use the log-traps command in the appropriate configuration mode. To remove this functionality, use the no form of this command.
log-traps
no log-traps
Syntax Description
This command has no keywords or arguments.
Command Default
This command is disabled by default.
Command Modes
Multicast routing configuration
Multicast routing address family IPv4 configuration
Multicast VRF configuration
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write |
Examples
The following example shows how to enable logging of trap events:
RP/0/RSP0/CPU0:router# multicast-routing RP/0/RSP0/CPU0:router(config-mcast)# log-traps
maximum disable
To disable maximum state limits, use the maximum disable command in the appropriate configuration mode. To remove this functionality, use the no form of this command.
maximum disable
no maximum disable
Syntax Description
This command has no keywords or arguments.
Command Default
Maximum state limits are enabled.
Command Modes
Multicast routing configuration
Multicast routing address family IPv4 configuration
Multicast VRF configuration
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the maximum disable command to override the default software limit on the number of multicast routes.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write |
Examples
The following example shows how to disable maximum state limits:
RP/0/RSP0/CPU0:router# multicast-routing RP/0/RSP0/CPU0:router(config-mcast)# maximum disable
mdt c-multicast-routing
To configure customer multicast routing (c-multicast-routing) for multicast distribution trees (MDT) and to enter the c-multicast-routing mode, use the mdt c-multicast-routing command in the appropriate mode. To delete the configuration, use the no form of the command.
mdt c-multicast-routing [ bgp | pim ]
no mdt c-multicast-routing [ bgp | pim ]
Syntax Description
| bgp |
Enables customer multicast routing for BGP. |
| pim |
Enables customer multicast routing for PIM. |
Command Default
None
Command Modes
PIM VRF address-family configuration mode
Command History
| Release | Modification |
|---|---|
|
Release 4.3 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Task ID
| Task ID | Operation |
|---|---|
| multicast |
read, write |
Examples
This example show how to run the mdt c-multicast-routing:
RP/0/RSP0/CPU0:router(config-pim-v1-ipv4) # mdt c-multicast-routing bgp
mdt data
To configure multicast data to be part of a multicast distribution tree (MDT) data group for multicast VPN (MVPN), use the mdt data command in the appropriate configuration mode. To remove this functionality, use the no form of this command.
mdt data mdt-group-address /mask [ threshold threshold-value ] [acl-name]
no mdt data mdt-group-address /prefix-length [ threshold threshold-value ] [acl-name]
Syntax Description
|
mdt-group-address |
IP address of the MDT group. |
|
/ mask |
A decimal value that indicates how many of the high-order contiguous bits of the address compose the prefix (the network portion of the address). A slash must precede the decimal value. |
|
threshold threshold |
Specifies the traffic rate threshold to trigger data MDT. Range is 1 to 4294967295. |
|
acl-name |
Access list (ACL) for the customer’s VRF groups allowed to perform data MDT. |
Command Default
threshold : 1
Command Modes
Multicast routing configuration
Multicast routing address family IPv4 and IPv6 configuration
Multicast VRF configuration
Command History
|
Release |
Modification |
|---|---|
|
Release 3.5.0 |
This command was introduced. |
|
Release 3.7.0 |
Additional keyword information was added to the command. The bottom of the threshold value range was increased by 1. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
When certain multicast streams exceed a configured bandwidth, the multicast data is moved to an MDT data group that is dynamically chosen from an available pool of multicast addresses. If the traffic bandwidth falls below the threshold, the source is switched back to the default MDT. To avoid transitions between the MDTs, traffic only reverts to the default MDT if traffic below the data MDT threshold is at least one minute old.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write |
Examples
The following example shows how to configure the data MDT group:
RP/0/RSP0/CPU0:router# multicast-routing RP/0/RSP0/CPU0:router(config-mcast)# mdt data 172.23.2.2/24 threshold 1200 acl_A
Related Commands
Command | Description |
| Configures the default group address of the multicast VPN (MVPN) multicast distribution tree (MDT). |
| Configures the maximum transmission unit (MTU) configuration of the multicast VPN (MVPN) multicast distribution tree (MDT). |
| Configures the interface used to set the multicast VPN (MVPN) data multicast distribution tree (MDT) source address. |
mdt data ingress replication
To configure ingress replication (IR) data for Multicast Distribution Trees (MDT), use the mdt data ingress replicationcommand in the appropriate mode. To remove the configuration, use the no form of the command.
mdt data ingress replication[ acl_name | immediate-switch | numbervalue | threshold value]
no mdt data ingress replication[ acl_name | immediate-switch | numbervalue | threshold value]
Syntax Description
| immediate-switch |
Enables switching to data MDT immediately. |
| acl_name |
ACL fo vrf groups that are enabled for data MDT |
| number value |
Maximum number of data MDTs to be triggered. Range is 1 to 262143. |
| immediate-switch value |
Traffic rate threshold (in kbps) to trigger data MDT. Range is 1 to 4294967. |
Command Default
None
Command Modes
Multicast routing VRF address-family configuration
Command History
| Release | Modification |
|---|---|
| Release 5.1.1 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Task ID
| Task ID | Operation |
|---|---|
| multicast |
read, write |
Examples
This example shows how to run the mdt data ingress replication command:
RP/0/RSP0/CPU0:router (config-mcast-v1-ipv4) # mdt data ingress-replication immediate-switch
mdt default
To configure the default group address of the multicast VPN (MVPN) multicast distribution tree (MDT), use the mdt default command in the appropriate configuration mode. To remove this functionality, use the no form of this command.
mdt default { mdt-default-group-address | ipv4 mdt-default-address }
no mdt default { mdt-default-group-address | ipv4 mdt-default-address }
Syntax Description
|
mdt-default-group-address |
IP address of the MDT default group entered in A.B.C.D. format. |
|
ipv4 |
Specifies IPv4-encapsulated MDT. |
|
mdt-default-address |
MDT IPv4 default address entered in A.B.C.D. format |
Command Default
The MDT default group address must be unique.
Command Modes
Multicast routing configuration
Multicast routing address family IPv4 and IPv6 configuration
Multicast VRF configuration
Command History
|
Release |
Modification |
|---|---|
|
Release 3.5.0 |
This command was introduced. |
|
Release 3.7.0 |
Additional keyword information was added. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The default MDT has a unique group address used to create MVPN multicast tunnel interfaces.
Although within the multicast VRF configuration submode, the MDT configuration uses either the ipv4 or ipv6 keyword to distinguish the appropriate multicast VPN, the MDT core tree is IPv4.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write |
Examples
The following example shows how to configure the MDT default group address from multicast routing configuration mode:
RP/0/RSP0/CPU0:router# multicast-routing RP/0/RSP0/CPU0:router(config-mcast)# mdt default 172.16.10.1
The following example shows how to configure the MDT default group address from multicast VRF configuration submode for an IPv6 address family:
RP/0/RSP0/CPU0:router# multicast-routing RP/0/RSP0/CPU0:router(config-mcast)# vrf vrf-name address-family ipv6 RP/0/RSP0/CPU0:router(config-mcast-vrf-name-ipv6)#mdt default 172.16.10.1
Related Commands
Command | Description |
| Configures multicast data to be part of a multicast distribution tree (MDT) data group for multicast VPN (MVPN). |
| Configures the maximum transmission unit (MTU) configuration of the multicast VPN (MVPN) multicast distribution tree (MDT). |
| Configures the interface used to set the multicast VPN (MVPN) data multicast distribution tree (MDT) source address. |
mdt mtu
To configure the maximum transmission unit (MTU) configuration of the multicast VPN (MVPN) multicast distribution tree (MDT), use the mdt mtu command in multicast VPN configuration mode. To remove this functionality, use the no form of this command.
mdt mtu value
no mdt mtu value
Syntax Description
|
value |
Specifies the MTU value and ranges between 401 to 65535. The configured mdt mtu value includes 24 bytes of GRE encapsulation. |
Command Default
The MDT tunnel default size is 1376.
Command Modes
Multicast VRF configuration
Command History
|
Release |
Modification |
|---|---|
|
Release 3.5.0 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write |
Examples
The following example shows how to configure the MTU of the multicast distribution tree:
RP/0/RSP0/CPU0:router# multicast-routing RP/0/RSP0/CPU0:router(config-mcast)# vrf vrf_A RP/0/RSP0/CPU0:router(config-mcast-vrf_A-ipv4)# mdt mtu 2345
Related Commands
Command | Description |
| Configures multicast data to be part of a multicast distribution tree (MDT) data group for multicast VPN (MVPN). |
| Configures the default group address of the multicast VPN (MVPN) multicast distribution tree (MDT). |
| Configures the interface used to set the multicast VPN (MVPN) data multicast distribution tree (MDT) source address. |
mdt source
To configure the interface used to set the multicast VPN (MVPN) data multicast distribution tree (MDT) source address, use the mdt source command in the appropriate configuration mode. To remove this functionality, use the no form of this command.
mdt source type interface-path-id
no mdt source type interface-path-id
Syntax Description
|
type |
Interface type. For more information, use the question mark (?) online help function. |
||
|
interface-path-id |
Physical interface or virtual interface.
For more information about the syntax for the router, use the question mark ( ? ) online help function. |
Command Default
No default behavior or values
Command Modes
Multicast routing configuration
Multicast routing address family IPv4 configuration
Multicast VRF configuration
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the mdt source command to identify the root of the multicast distribution tree in the service provider network. This address is used to update all MVPN peers through multiprotocol BGP.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write |
Examples
The following example shows how to configure the interface used to set the MDT source address:
RP/0/RSP0/CPU0:router# multicast-routing RP/0/RSP0/CPU0:router(config-mcast)# mdt source POS 0/1/0/0
Note | Per VRF MDT Source is a new feature introduced in IOS XR Software Release 3.9.0 apart from the existing default MDT source. Each VRF can have its own MDT source interface co-existing with the default MDT source to achieve core diversity. |
The following example shows how to configure a per VRF MDT source:
RP/0/RSP0/CPU0:router# configure RP/0/RSP0/CPU0:router(config)# multicast-routing RP/0/RSP0/CPU0:router(config-mcast)# address-family ipv4 RP/0/RSP0/CPU0:router(config-mcast-default-ipv4)# mdt source loopback0 RP/0/RSP0/CPU0:router(config-mcast)# vrf foo RP/0/RSP0/CPU0:router(config-mcast-foo)# address-family ipv4 RP/0/RSP0/CPU0:router(config-mcast-foo-ipv4)# mdt source loopback1 !
Related Commands
Command | Description |
| Configures multicast data to be part of a multicast distribution tree (MDT) data group for multicast VPN (MVPN). |
| Configures the default group address of the multicast VPN (MVPN) multicast distribution tree (MDT). |
| Configures the maximum transmission unit (MTU) configuration of the multicast VPN (MVPN) multicast distribution tree (MDT). |
migration route-policy
To support PIM And BGP c-multicast joins over the same or different MDTs, use the migration route-policycommand in the appropriate mode. To disable the migration, use the noform of the command.
migration route-policy policy-name
nomigration route-policy policy-name
Syntax Description
| policy-name |
Name of the policy. |
Command Default
None
Command Modes
C-multicast routing configuration mode
Command History
| Release | Modification |
|---|---|
|
Release 4.3 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The policy name is used to match the upstream PEs (nexthop) and send joins through BGP or PIM.
Task ID
| Task ID | Operation |
|---|---|
| multicast |
read, write |
Examples
This example shows how to use the migration route-policycommand:
RP/0/RSP0/CPU0:router (config-pim-v1-ipv4-mdt-cmcast) # migration route-policy p1
multicast-routing
global
configuration mode. To return to the default behavior, use the no form of this command.multicast-routing
no multicast-routing
Syntax Description
This command has no keywords or arguments.
Command Default
No default behavior or values.
Command Modes
Global configuration
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write |
Examples
The following example shows how to enter multicast routing configuration mode:
RP/0/RSP0/CPU0:router(config)# multicast-routing RP/0/RSP0/CPU0:router(config-mcast)#
Related Commands
|
Command |
Description |
|---|---|
|
Enables per-prefix counters only in hardware. |
|
|
alias |
Creates a command alias. |
|
Configures multicast interface properties. |
|
|
Enables multicast routing and forwarding on all new and existing interfaces. |
multipath
To enable Protocol Independent Multicast (PIM) to divide the multicast load among several equal cost paths, use the multipath command in the appropriate configuration mode. To return to the default behavior, use the no form of this command.
[ address-family ipv4 ] multipath [ hash { source | source next-hop } ]
no multipath
Syntax Description
|
hash |
(Optional) Enables multipath hashing. |
|
source |
Enables source-based multipath hashing. |
|
source-nexthop |
(Optional) Enables source with next-hop hashing. |
Command Default
This command is disabled by default.
Command Modes
Multicast routing configuration
Multicast routing address-family ipv4
Multicast VRF configuration
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
By default, equal-cost multipath (ECMP) paths are not load balanced. A single path from each unicast route is used for all multicast routes (which is the equivalent of the no form of the multipath command).
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write |
Examples
The following example shows how to enable multipath functionality:
RP/0/RSP0/CPU0:router(config)# multicast-routing RP/0/RSP0/CPU0:router(config-mcast)# multipath hash
nsf (multicast)
To turn on the nonstop forwarding (NSF) capability for the multicast routing system, use the nsf command in multicast routing configuration mode. To turn off this function, use the no form of this command.
nsf [ lifetime seconds ]
no nsf [lifetime]
Syntax Description
|
lifetime seconds |
(Optional) Specifies the maximum time (in seconds) for NSF mode. Range is 30 to 3600. |
Command Default
This command is disabled by default.
Command Modes
Multicast routing configuration
Multicast routing address family ipv4 configuration
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The nsf command does not enable or disable the multicast routing system, but just the NSF capability for all the relevant components. When the no form of this command is used, the NSF configuration is returned to its default disabled state.
Enable multicast NSF when you require enhanced availability of multicast forwarding. When enabled, failures of the control-plane multicast routing components Multicast Routing Information Base (MRIB) or Protocol Independent Multicast (PIM) will not cause multicast forwarding to stop. When these components fail or communication with the control plane is otherwise disrupted, existing Multicast Forwarding Information Base (MFIB) entries continue to forward packets until either the control plane recovers or the MFIB NSF timeout expires.
Enable multicast NSF when you upgrade control-plane Cisco IOS XR Software packages so that the live upgrade process does not interrupt forwarding.
When the MFIB partner processes enter NSF mode, forwarding on stale (nonupdated) MFIB entries continues as the control-plane components attempt to recover gracefully. Successful NSF recovery is signaled to the Multicast Forwarding Engine (MFWD) partner processes by MRIB. MRIB remains in NSF mode until Internet Group Management Protocol (IGMP) has recovered state from the network and host stack and until PIM has recovered state from the network and IGMP. When both PIM and IGMP have recovered and fully updated the MRIB, MRIB signals the MFIBs that NSF is ending, and begins updating the stale MFIB entries. When all updates have been sent, the MFWD partner processes delete all remaining stale MFIB entries and returns to normal operation, ending the NSF mode. MFIB NSF timeout prior to the signal from MRIB may cause NSF to end, and thus forwarding to stop.
When forwarding is in NSF mode, multicast flows may continue longer than necessary when network conditions change due to multicast routing protocols, unicast routing protocol reachability information, or local sender and receiver changes. The MFWD partner processes halt forwarding on stale MFIB entries when the potential for a multicast loop is detected by receipt of incoming data on a forwarding interface for the matching MFIB entry.
Note | For NSF to operate successfully in your multicast network, you must also enable NSF for the unicast protocols (such as Intermediate System-to-Intermediate System [IS-IS], Open Shortest Path First [OSPF] and Border Gateway Protocol [BGP]) that PIM relies on for Reverse Path Forwarding (RPF) information. See the appropriate configuration modules to learn how to configure NSF for unicast protocols. |
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write |
Examples
The following example shows how to enable NSF for the multicast routing system:
RP/0/RSP0/CPU0:router(config)# multicast-routing RP/0/RSP0/CPU0:router(config-mcast)# nsf
Related Commands
|
Command |
Description |
|---|---|
|
nsf lifetime (IGMP) |
Configures the maximum time for the NSF timeout value under IGMP. |
|
nsf lifetime (PIM) |
Configures the NSF timeout value for the PIM process. |
|
show igmp nsf |
Displays the state of NSF operation in IGMP. |
|
show mfib nsf |
Displays the state of NSF operation for the MFIB line cards. |
|
Displays the state of NSF operation in the MRIB. |
|
|
show pim nsf |
Displays the state of NSF operation for PIM. |
oom-handling
To enable the out-of-memory (OOM) functionality on multicast routing software components, use the oom-handling command in multicast routing configuration mode. To remove this functionality, use the no form of this command.
oom-handling
no oom-handling
Syntax Description
This command has no keywords or arguments.
Command Default
This command is disabled by default.
Command Modes
Multicast routing configuration
Multicast routing address family ipv4 configuration
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
When the oom-handling command is enabled, and the router memory is low or in a warning state, the following states are not created:
- Protocol Independent Multicast (PIM) route states in response to PIM join and prune messages, and register messages
- Internet Group Management Protocol (IGMP) group states
- External Source-Active (SA) states in Multicast Source Discovery Protocol (MSDP)
Multicast routing show commands such as the show pim topology command indicate when the router is running low on memory and that new state creation has stopped.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write |
Examples
The following example shows how to enable the out-of-memory functionality:
RP/0/RSP0/CPU0:router# multicast-routing RP/0/RSP0/CPU0:router(config-mcast)# oom-handling
Related Commands
|
Command |
Description |
|---|---|
|
show pim topology |
Displays PIM topology table information. |
rate-per-route
To enable individual (source, group [S, G]) rate calculations, use the rate-per-route command in the appropriate configuration mode. To remove this functionality, use the no form of this command.
rate-per-route
no rate-per-route
Syntax Description
This command has no keywords or arguments.
Command Default
This command is disabled by default.
Command Modes
Multicast routing configuration
Multicast routing address family ipv4 configuration
Multicast VRF configuration
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write |
Examples
The following example shows how to enable individual route calculations:
RP/0/RSP0/CPU0:router# multicast-routing vrf vpn12 address-family ipv4 RP/0/RSP0/CPU0:router(config-mcast)# rate-per-route
Related Commands
Command | Description |
| Displays route entries in the Multicast Forwarding Information Base (MFIB). |
shared-tree-prune delay
To set or change the prune installation time, use the shared-tree-prune-delaycommand in the appropriate mode. To disable the set time, use the no form of the command.
shared-tree-prune-delay time
noshared-tree-prune-delay time
Syntax Description
| time |
Delay in seconds. Range is 0 to 1800. |
Command Default
60 seconds (for upstream prune)
Command Modes
C-multicast-routing configuration mode
Command History
| Release | Modification |
|---|---|
|
Release 4.3 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
This command is used to change the prune installation time(C-S, C-G, RPT). This is required on PEs connected to the C-RP (under certain conditions), when a Type-5 route is received. This is applicable only to BGP C-multicast Routing.
Task ID
| Task ID | Operation |
|---|---|
| multicast |
read, write |
Examples
This example shows how to use the shared-tree-prune-delay command:
RP/0/RSP0/CPU0:router (config-pim-v1-ipv4-mdt-cmcast) # shared-tree-prune-delay 100
show mfib bvi
To display the Bridge Virtual Interface (BVI) details in the Multicast Forwarding Information Base (MFIB), use the show mfib bvi command EXEC mode.
show mfib bvi[ interface| route] bvibvi_number
Syntax Description
| interface |
MFIB BVI interface. |
| route |
BVI route entry. |
| bvi_number |
BVI interface number. Range is from 1 to 65535. |
Command Default
None
Command Modes
EXEC
Command History
| Release | Modification |
|---|---|
| Release 5.1.1 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Task ID
| Task ID | Operation |
|---|---|
| multicast |
read |
Examples
This example shows how to run the show mfib bvi command:
RP/0/RSP0/CPU0:router # show mfib bvi route bvi 200
show mfib connections
To display the status of Multicast Forwarding Information Base (MFIB) connections to servers, use the show mfib connections command in the appropriate mode.
Syntax Description
|
ipv4 |
(Optional) Specifies IPv4 address prefixes. |
|
ipv6 |
(Optional) Specifies IPv6 address prefixes. |
|
location node-id |
(Optional) Specifies MFIB connections associated with an interface of the designated node. |
Command Default
IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the show mfib connections command to display a list of servers connected to the MFIB and the status of the connections.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read |
Examples
The following is sample output from the show mfib connections command:
RP/0/RSP0/CPU0:router# show mfib connections
Netio : connected
IM : connected
Pakman : connected
MRIB : connected
IFH : connected
SysDB-Global : connected
SysDB-Local : connected
SysDB-NSF : connected
SYSDB-EDM : connected
SYSDB-Action : connected
AIB : connected
MLIB : connected
IDB : connected
IIR : connected
IPARM : connected
GSP : connected
Related Commands
Command | Description |
| Displays interface-related information used during software multicast switching in the Multicast Forwarding Information Base (MFIB) process. |
| Displays route entries in the Multicast Forwarding Information Base (MFIB). |
show mfib counter
To display Multicast Forwarding Information Base (MFIB) counter statistics for packets that have dropped, use the show mfib counter command in the appropriate mode.
show mfib [ vrf vrf-name ] ipv4 counter [ location node-id ]
Syntax Description
|
vrf vrf-name |
(Optional) Specifies a VPN routing and forwarding (VRF) instance. |
|
ipv4 |
(Optional) Specifies IPv4 address prefixes. |
|
location node-id |
(Optional) Specifies MFIB counter statistics associated with an interface of the designated node. |
Command Default
IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The show mfib counter command displays packet drop statistics for packets that cannot be accounted for under route counters.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read |
Examples
The following is sample output from the show mfib counter command:
RP/0/RSP0/CPU0:router# show mfib counter location 0/1/CPU0
MFIB global counters are :
* Packets [no input idb] : 0
* Packets [failed route lookup] : 0
* Packets [Failed idb lookup] : 0
* Packets [Mcast disabled on input I/F] : 0
* Packets [encap drops due to ratelimit] : 0
* Packets [MC disabled on input I/F (iarm nfn)] : 0
|
Field |
Description |
|---|---|
|
Packets [no input idb] |
Packets dropped because no input interface information was found in the packet. |
|
Packets [failed route lookup] |
Packets dropped because of failure to match any multicast route. |
|
Packets [Failed idb lookup] |
Packets dropped because the descriptor block was not found for an interface (incoming or outgoing). |
|
Packets [Mcast disabled on input I/F] |
Packets dropped because arriving on an interface that was not enabled for the multicast routing feature. |
|
Packets [encap drops due to ratelimit] |
Packets dropped because of rate limit. |
Related Commands
Command | Description |
| Displays interface-related information used during software multicast switching in the Multicast Forwarding Information Base (MFIB) process. |
| Displays route entries in the Multicast Forwarding Information Base (MFIB). |
show mfib encap-info
To display the status of encapsulation information for Multicast Forwarding Information Base (MFIB), use the show mfib encap-info command in the appropriate mode.
show mfib [ vrf vrf-name ] [ ipv4 | ipv6 ] encap-info [ location node-id ]
Syntax Description
|
vrf vrf-name |
(Optional) Specifies a VPN routing and forwarding (VRF) instance. |
|
ipv4 |
(Optional) Specifies IPv4 address prefixes. |
|
ipv6 |
(Optional) Specifies IPv6 address prefixes. |
|
location node-id |
(Optional) Specifies MFIB connections associated with an interface of the designated node. |
Command Default
IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read |
Examples
The following is sample output from the show mfib encap-info command:
RP/0/RSP0/CPU0:router# show mfib vrf vrf_a encap-info
----------------------------
Encaps String Dependent Encaps MDT Name/
Routes # Table ID Handle
(192.168.5.203, 255.1.1.1) 5 0xe0000000 mdtA1 (0x100a480)
Related Commands
Command | Description |
| Displays interface-related information used during software multicast switching in the Multicast Forwarding Information Base (MFIB) process. |
| Displays route entries in the Multicast Forwarding Information Base (MFIB). |
show mfib hardware interface
EXEC mode
.show mfib [ vrf vrf-name ] [ ipv4 | ipv6 ] hardware interface [detail] [ type interface-path-id ] [ location node-id ]
Syntax Description
|
vrf vrf-name |
(Optional) Specifies a VPN routing and forwarding (VRF) instance. |
||
|
ipv4 |
(Optional) Specifies IPv4 address prefixes. |
||
|
ipv6 |
(Optional) Specifies IPv6 address prefixes. |
||
|
detail |
(Optional) Displays detailed information about the MFIB interface. |
||
|
type |
(Optional) Interface type. For more information, use the question mark (?) online help function. |
||
|
interface-path-id |
(Optional) Physical interface or virtual interface.
For more information about the syntax for the router, use the question mark (?) online help function. |
||
|
location node-id |
(Optional) Specifies an MFIB-designated node. |
Command Default
IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The show mfib hardware interface command displays multicast-specific information about the software switching interfaces of the router hardware. This command will not display any useful output if only RSP is specified or if no location is specified.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read |
Examples
The following is sample output from the show mfib hardware interface command.
RP/0/RSP0/CPU0:router# show mfib hardware interface location 0/0/CPU0
LC Type: Trident
--------------------------------------------------------------------
Interface Handle RefCnt TTL Routes uIDB Enbld Comment
--------------------------------------------------------------------
Gi0/0/0/4 0x180 5 0 2 5 True success
Gi0/0/0/5 0x1c0 27 0 0 6 True success
Gi0/0/0/6 0x200 5 0 2 7 True success
Gi0/0/0/7 0x240 25 0 0 8 True success
Gi0/0/0/8 0x280 30 0 2 9 True success
--------------------------------------------------------------------
ROUTE INFORMATION:
Legend:
S: Source, G: Group, P: Prefix length, PI: Packets cn, PO: packets out,
RF: RPF failures, TF: TTL failures, OF: OLIST failures, F: Other failures
Route flags - (Ingress)
C: Chip ID, IC: BACL check, IP: Punt this packet to LC CPU,
ID: Directly connected, IS: RPF interface signal, IU: Punt copy to RP,
IF: Punt to LC CPU if forwarded, IM: Result match, IV: Valid entry,
IR: RPF IF, IA: Fabric slotmask, IG: Mulicast group ID
Route flags - (Egress)
ET: Table ID to be used for OLIST lookup, EO: OLIST count bit,
ER: Route MGID to be used for OLIST/NRPF lookup, EM: Result match,
EV: Valid entry, EC: Count of OLIST members on this chip,
BS: Base of the statistics pointer
Interface: Gi0/0/0/4
S:4.0.0.2 G:227.0.0.1 P:32 PI:1 PO:0 RF:0 TF:0 OF:0 F:0
---------------------------------------------------------------------------------
C IC IP ID IS IU IF IM IV IR IA IG ET EO ER EM EV EC BS
---------------------------------------------------------------------------------
0 F F F F F F T T 0x180 0x1 0x8006 0 F 6 T T 0 0x5518a
1 F F F F F F T T 0x180 0x1 0x8006 0 F 6 T T 0 0x5518a
2 F F F F F F T T 0x180 0x1 0x8006 0 F 6 T T 0 0x5518a
3 F F F F F F T T 0x180 0x1 0x8006 1 T 6 T T 3 0x555c2
---------------------------------------------------------------------------------
S:0.0.0.0 G:227.0.0.1 P:32 PI:4 PO:0 RF:0 TF:0 OF:0 F:0
---------------------------------------------------------------------------------
C IC IP ID IS IU IF IM IV IR IA IG ET EO ER EM EV EC BS
---------------------------------------------------------------------------------
0 F F T F F F T T 0x0 0x1 0x8004 0 F 5 T T 0 0x55185
1 F F T F F F T T 0x0 0x1 0x8004 0 F 5 T T 0 0x55185
2 F F T F F F T T 0x0 0x1 0x8004 0 F 5 T T 0 0x55185
3 F F T F F F T T 0x0 0x1 0x8004 1 T 5 T T 3 0x555bd
---------------------------------------------------------------------------------
Interface: Gi0/0/0/5
This interface is not part of the olist of any route
Interface: Gi0/0/0/6
S:4.0.0.2 G:227.0.0.1 P:32 PI:1 PO:0 RF:0 TF:0 OF:0 F:0
---------------------------------------------------------------------------------
C IC IP ID IS IU IF IM IV IR IA IG ET EO ER EM EV EC BS
---------------------------------------------------------------------------------
0 F F F F F F T T 0x180 0x1 0x8006 0 F 6 T T 0 0x5518a
1 F F F F F F T T 0x180 0x1 0x8006 0 F 6 T T 0 0x5518a
2 F F F F F F T T 0x180 0x1 0x8006 0 F 6 T T 0 0x5518a
3 F F F F F F T T 0x180 0x1 0x8006 1 T 6 T T 3 0x555c2
---------------------------------------------------------------------------------
S:0.0.0.0 G:227.0.0.1 P:32 PI:4 PO:0 RF:0 TF:0 OF:0 F:0
---------------------------------------------------------------------------------
C IC IP ID IS IU IF IM IV IR IA IG ET EO ER EM EV EC BS
---------------------------------------------------------------------------------
0 F F T F F F T T 0x0 0x1 0x8004 0 F 5 T T 0 0x55185
1 F F T F F F T T 0x0 0x1 0x8004 0 F 5 T T 0 0x55185
2 F F T F F F T T 0x0 0x1 0x8004 0 F 5 T T 0 0x55185
3 F F T F F F T T 0x0 0x1 0x8004 1 T 5 T T 3 0x555bd
---------------------------------------------------------------------------------
Interface: Gi0/0/0/7
This interface is not part of the olist of any route
Interface: Gi0/0/0/8
S:4.0.0.2 G:227.0.0.1 P:32 PI:1 PO:0 RF:0 TF:0 OF:0 F:0
---------------------------------------------------------------------------------
C IC IP ID IS IU IF IM IV IR IA IG ET EO ER EM EV EC BS
---------------------------------------------------------------------------------
0 F F F F F F T T 0x180 0x1 0x8006 0 F 6 T T 0 0x5518a
1 F F F F F F T T 0x180 0x1 0x8006 0 F 6 T T 0 0x5518a
2 F F F F F F T T 0x180 0x1 0x8006 0 F 6 T T 0 0x5518a
3 F F F F F F T T 0x180 0x1 0x8006 1 T 6 T T 3 0x555c2
---------------------------------------------------------------------------------
S:0.0.0.0 G:227.0.0.1 P:32 PI:4 PO:0 RF:0 TF:0 OF:0 F:0
---------------------------------------------------------------------------------
C IC IP ID IS IU IF IM IV IR IA IG ET EO ER EM EV EC BS
---------------------------------------------------------------------------------
0 F F T F F F T T 0x0 0x1 0x8004 0 F 5 T T 0 0x55185
1 F F T F F F T T 0x0 0x1 0x8004 0 F 5 T T 0 0x55185
2 F F T F F F T T 0x0 0x1 0x8004 0 F 5 T T 0 0x55185
3 F F T F F F T T 0x0 0x1 0x8004 1 T 5 T T 3 0x555bd
---------------------------------------------------------------------------------
The following example shows a sample output for show mfib hardware interface command on the Cisco ASR 9000 Series SIP-700 line card:
RP/0/RSP0/CPU0:router# show mfib hardware interface serial 0/4/0/0/1 location 0/4/CPU0
LC Type: A9K-SIP-700
Hardware Interface Information
-------------------------------------------------------------
Interface Handle Type TTL Number of Routes Multicast Enabled Num bundles
-------------------------------------------------------------
Se0/4/0/0/1 0xc000ec0 0 0 2 True 0
-------------------------------------------------------------
Header : IDB Route Information
Source : Source address
Group : Group Address
M : Mask Length
PI : Packets in
PO : Packets out
RF : RPF failures
TF : TTL failures
OF : OLIST failures
F : Other failures
C : Directly connected check flag
RPF : Accepting interface for non-bidir entries
S : Signal if packet arrived on RPF interface
IC : Aggregated Internal copy flag
PR : Punt to RP flag for Internal copy in the Loopback interface
PK : PEEK flag
FGID : Fabric Group ID
MGID : Multicast Group ID
Interface: Se0/4/0/0/1
Source: 12.12.12.2 Group: 225.0.0.0 M: 64 PI: 1 PO: 0 RF: 0 TF: 0 OF: 0 F: 0
C: F RPF: Se0/4/0/0/1 S: F IC: F PR: F PK: F FGID: 64 MGID: 17024
Ingress CPP Prefix Information
-----------------------------------------------------
=== QFP Multicast prefix info ===
Root: 9dcbcfb0, Flags: 0 First leaf: 9dcbccfc
Number of nodes: 0x000001, leaves: 0x000001 RPF i/f: 0x007fff
RPF Fast Convergence flags: 00000000 Secondary RPF: 00000000
RPF Fast Convergence timer: 0 ext_leaf: 0x8b900200
Egress CPP Prefix Information
-----------------------------------------------------
=== QFP Multicast prefix info ===
Root: 9dcbcfb0, Flags: 0 First leaf: 9dcbccfc
Number of nodes: 0x000001, leaves: 0x000001 RPF i/f: 0x007fff
RPF Fast Convergence flags: 00000000 Secondary RPF: 00000000
RPF Fast Convergence timer: 0 ext_leaf: 0x8ce80200
Route OCE Entry Information
-----------------------------------------------------
**** Leaf Info (in cp) : [9dcbccfc]
oce flags = 0x2 next obj type : 11 next obj handle : a73e9104
**** Leaf Info (in cpp): [0]
leaf_flags= 0x1 oce_flags: 0 oce_ptr: 0x8c5800c0
Source: 0.0.0.0 Group: 225.0.0.0 M: 32 PI: 1 PO: 0 RF: 0 TF: 0 OF: 0 F: 0
C: T RPF: Se0/4/0/0/1 S: F IC: F PR: F PK: F FGID: 64 MGID: 17013
Ingress CPP Prefix Information
-----------------------------------------------------
=== QFP Multicast prefix info ===
Root: 9dcbd530, Flags: 2 First leaf: 9dcbd9bc
Number of nodes: 0x000001, leaves: 0x000001 RPF i/f: 0x007fff
RPF Fast Convergence flags: 00000000 Secondary RPF: 00000000
RPF Fast Convergence timer: 0 ext_leaf: 0x8b900080
Egress CPP Prefix Information
-----------------------------------------------------
=== QFP Multicast prefix info ===
Root: 9dcbd530, Flags: 2 First leaf: 9dcbd9bc
Number of nodes: 0x000001, leaves: 0x000001 RPF i/f: 0x007fff
RPF Fast Convergence flags: 00000000 Secondary RPF: 00000000
RPF Fast Convergence timer: 0 ext_leaf: 0x8ce80080
Route OCE Entry Information
-----------------------------------------------------
**** Leaf Info (in cp) : [9dcbd9bc]
oce flags = 0x6 next obj type : 11 next obj handle : a73e9104
**** Leaf Info (in cpp): [0]
leaf_flags= 0x1 oce_flags: 0 oce_ptr: 0x8c5800c0
|
Field |
Description |
|---|---|
|
Interface |
MFIB interface name. |
|
Handle |
A 32-bit system-wide identifier of the MFIB interface. |
|
RefCnt |
Number of times various data structures referred to this MFIB interface structure. |
|
TTL |
Multicast time-to-live threshold that was configured on this MFIB interface. |
|
Routes |
The number of routes that include this interface as a member. |
|
uIDB |
The ucode Interface Descriptor Block index. |
|
Enbld |
If true, multicast is enabled on the MFIB interface. |
|
Comment |
Indicates whether there were problems when reading hardware information. |
Related Commands
Command | Description |
| Displays interface-related information used during software multicast switching in the Multicast Forwarding Information Base (MFIB) process. |
show mfib hardware ltrace
EXEC mode
.show mfib [ vrf vrf-name ] [ ipv4 | ipv6 ] hardware ltrace [ error | event | frequent-event | hexdump | init | last | netio | reverse | stats | tailf | unique | verbose | wrapping ] file file-name location node-id
Syntax Description
|
vrf vrf-name |
(Optional) Specifies a VPN routing and forwarding (VRF) instance. |
|
ipv4 |
(Optional) Specifies IPv4 address prefixes. |
|
ipv6 |
(Optional) Specifies IPv6 address prefixes. |
|
error |
(Optional) Displays error events. |
|
event |
(Optional) Displays non-frequent events. |
|
frequent-event |
(Optional) Displays frequent events. |
|
hexdump |
(Optional) Displays traces in hexadecimal ouput. |
|
init |
(Optional) Displays initiation and configuration events. |
|
last |
(Optional) Displays the last n entries. |
|
netio |
(Optional) Displays the netio events. |
|
reverse |
(Optional) Displays the traces in the reverse order starting with the latest events. |
|
stats |
(Optional) Displays the statistics. |
|
tailf |
(Optional) Displays the new traces as they are added. |
|
unique |
(Optional) Displays the unique entries with the counts. |
|
verbose |
(Optional) Displays the internal debugging information. |
|
wrapping |
(Optional) Displays the wrapping entries. |
|
file file-name |
(Optional) Specifies the file name. |
|
location node-id |
Specifies an MFIB-designated node. |
Command Default
IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
|
Release 4.0.0 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Note | This command will not display any useful output if only RSP is specified or if no location is specified. |
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read |
Examples
The following is sample output from the show mfib hardware ltrace command:
RP/0/RSP0/CPU0:router# show mfib hardware ltrace error location 0/1/cpu
3079 wrapping entries (4096 possible, 0 filtered, 4242 total)
May 21 01:45:32.865 ipmcast/error 0/1/CPU0 t1 Traffic Loss msg rxed, Null Route
, cntid=0x705f0
May 21 01:45:32.877 ipmcast/error 0/1/CPU0 t1 Traffic Loss msg rxed, Null Route
, cntid=0x705f2
May 21 01:58:37.019 ipmcast/error 0/1/CPU0 t1 Traffic Loss msg rxed, Null Route
, cntid=0x705f0
May 21 01:58:37.019 ipmcast/error 0/1/CPU0 t1 Traffic Loss msg rxed, Null Route
, cntid=0x705f2
May 21 02:15:38.620 ipmcast/error 0/1/CPU0 t1 Traffic Loss msg rxed, Null Route
, cntid=0x705f0
May 21 02:15:38.620 ipmcast/error 0/1/CPU0 t1 Traffic Loss msg rxed, Null Route
, cntid=0x705f2
May 21 02:26:06.440 ipmcast/error 0/1/CPU0 t1 Traffic Loss msg rxed, Null Route
, cntid=0x705f0
May 21 02:26:06.440 ipmcast/error 0/1/CPU0 t1 Traffic Loss msg rxed, Null Route
, cntid=0x705f2
May 21 03:11:18.805 ipmcast/error 0/1/CPU0 t1 Traffic Loss msg rxed, Null Route
, cntid=0x705f0
May 21 03:11:18.805 ipmcast/error 0/1/CPU0 t1 Traffic Loss msg rxed, Null Route
, cntid=0x705f2
May 21 03:36:31.240 ipmcast/error 0/1/CPU0 t1 Traffic Loss msg rxed, Null Route
, cntid=0x705f0
The following is a sample output for the show mfib hardware ltrace command on the Cisco ASR 9000 Series SIP-700 line card:
RP/0/RSP0/CPU0:router# show mfib hardware ltrace location 0/4/CPU0
438 wrapping entries (88064 possible, 0 filtered, 438 total)
Aug 25 00:22:02.978 mfwd_ipv4_hw/init 0/4/CPU0 t1 ===>> Proc started jid=199, pid=163944
Aug 25 00:22:02.978 mfwd_ipv4_hw/event 0/4/CPU0 t1 ===>> Proc started jid=199, pid=163944
Aug 25 00:22:02.978 mfwd_ipv4_hw/error 0/4/CPU0 t1 ===>> Proc started jid=199, pid=163944
Aug 25 00:22:02.978 mfwd_ipv4_hw/fevent 0/4/CPU0 t1 ===>> Proc started jid=199, pid=163944
Aug 25 00:22:02.978 mfwd_ipv4_hw/netio 0/4/CPU0 t1 ===>> Proc started jid=199, pid=163944
Aug 25 00:22:03.001 mfwd_ipv4_hw/init 0/4/CPU0 t1 MFWD: Platform lib initializiation started
Aug 25 00:22:03.001 mfwd_ipv4_hw/init 0/4/CPU0 t1 Successfully got shared memory window header
Aug 25 00:22:03.001 mfwd_ipv4_hw/init 0/4/CPU0 t1 Platform extension does not exist - cold boot
Aug 25 00:22:03.042 mfwd_ipv4_hw/init 0/4/CPU0 t1 CPP IPMC Gtrie Lib Init done: rc=0
Aug 25 00:22:03.075 mfwd_ipv4_hw/init 0/4/CPU0 t1 Library not initialized previously, establishing connections
Aug 25 00:22:23.990 mfwd_ipv4_hw/init 0/4/CPU0 t1 CPP IPMC PAL Lib Init done: rc=0
Aug 25 00:22:24.851 mfwd_ipv4_hw/init 0/4/CPU0 t1 CPP IPMC iox Init done: rc=0
Aug 25 00:22:24.852 mfwd_ipv4_hw/init 0/4/CPU0 t1 Successfully initiated thread ctx and API ctx
Aug 25 00:22:24.871 mfwd_ipv4_hw/init 0/4/CPU0 t1 Successfully done binding with CPP GIC Server
Aug 25 00:22:24.898 mfwd_ipv4_hw/init 0/4/CPU0 t1 Successfully done binding with CPP GIC Server
Aug 25 00:22:24.902 mfwd_ipv4_hw/init 0/4/CPU0 t1 Successfully binded with CPP Rx Adjacency APIs Lib
Aug 25 00:22:24.904 mfwd_ipv4_hw/init 0/4/CPU0 t1 Successfully binded with CPP Tx Adjacency APIs Lib
Aug 25 00:22:24.906 mfwd_ipv4_hw/init 0/4/CPU0 t1 Successfully binded with CPP Tx Adjacency APIs Lib
Aug 25 00:22:24.906 mfwd_ipv4_hw/init 0/4/CPU0 t1 Initialized interface lib
Aug 25 00:22:24.979 mfwd_ipv4_hw/init 0/4/CPU0 t1 Initialized EDM backend
Aug 25 00:22:24.999 mfwd_ipv4_hw/init 0/4/CPU0 t1 Initialized utilities lib
Aug 25 00:22:25.000 mfwd_ipv4_hw/init 0/4/CPU0 t1 MFWD: Platform lib initializiation completed
Aug 25 00:22:26.046 mfwd_ipv4_hw/event 0/4/CPU0 t1 table: table id -536870912 vrf id 1610612736 got created/commit table_ext 0x9dc89c10
Aug 25 00:22:26.098 mfwd_ipv4_hw/init 0/4/CPU0 t1 gtrie: Platform gtrie lib init started
Aug 25 00:22:26.099 mfwd_ipv4_hw/init 0/4/CPU0 t1 CPP IPMC gtrie init done prot=2 tab=0 rc=0
Aug 25 00:22:26.099 mfwd_ipv4_hw/init 0/4/CPU0 t1 gtrie: successfully initiated gtrie 0xa6039dec for protocol 0, table id 0, use shmem 1, shmem id 1
Aug 25 00:23:00.459 mfwd_ipv4_hw/event 0/4/CPU0 t1 CPP Create adj cpp 1 adj handle 0xa73e907c ifh 91 link 1 enctype 0 flags 1 hw addr 0x8c580000
Aug 25 00:24:25.780 mfwd_ipv4_hw/event 0/4/CPU0 t1 CPP Create adj cpp 1 adj handle 0xa73e90c0 ifh 98 link 1 enctype 0 flags 1 hw addr 0x8c580010
Aug 25 21:43:52.966 mfwd_ipv4_hw/init 0/4/CPU0 t1 MFWD: Platform lib terminate started, terminate reason 2
Aug 25 21:43:52.982 mfwd_ipv4_hw/init 0/4/CPU0 t1 MFWD: Platform lib terminate completed
Aug 25 21:43:55.783 mfwd_ipv4_hw/fevent 0/4/CPU0 t1 ===>> Proc started jid=199, pid=217192
Aug 25 21:43:55.783 mfwd_ipv4_hw/netio 0/4/CPU0 t1 ===>> Proc started jid=199, pid=217192
Aug 25 21:43:55.783 mfwd_ipv4_hw/error 0/4/CPU0 t1 ===>> Proc started jid=199, pid=217192
Aug 25 21:43:55.783 mfwd_ipv4_hw/event 0/4/CPU0 t1 ===>> Proc started jid=199, pid=217192
Aug 25 21:43:55.783 mfwd_ipv4_hw/init 0/4/CPU0 t1 ===>> Proc started jid=199, pid=217192
Aug 25 21:43:55.784 mfwd_ipv4_hw/init 0/4/CPU0 t1 MFWD: Platform lib initializiation started
Aug 25 21:43:55.784 mfwd_ipv4_hw/init 0/4/CPU0 t1 Successfully got shared memory window header
Aug 25 21:43:55.784 mfwd_ipv4_hw/init 0/4/CPU0 t1 Platform extension exists - warm boot
Aug 25 21:43:55.785 mfwd_ipv4_hw/init 0/4/CPU0 t1 CPP IPMC Gtrie Lib Init done: rc=0
Aug 25 21:43:55.797 mfwd_ipv4_hw/init 0/4/CPU0 t1 gtrie: Platform gtrie lib re-init started for gtrie 0xa6039dec, shmem id 1
Aug 25 21:43:55.797 mfwd_ipv4_hw/init 0/4/CPU0 t1 CPP IPMC gtrie re init done prot=2 tab=0 rc=0
Aug 25 21:43:55.797 mfwd_ipv4_hw/init 0/4/CPU0 t1 gtrie: successfully re-initiated gtrie 0xa6039dec for protocol 0, table id 0, use shmem 1, shmem id 1
Aug 25 21:43:55.826 mfwd_ipv4_hw/init 0/4/CPU0 t1 Library not initialized previously, establishing connections
Aug 25 21:43:56.241 mfwd_ipv4_hw/init 0/4/CPU0 t1 CPP IPMC PAL Lib Init done: rc=0
Aug 25 21:43:56.422 mfwd_ipv4_hw/init 0/4/CPU0 t1 CPP IPMC iox Init done: rc=0
Aug 25 21:43:56.423 mfwd_ipv4_hw/init 0/4/CPU0 t1 Successfully initiated thread ctx and API ctx
Aug 25 21:43:56.431 mfwd_ipv4_hw/init 0/4/CPU0 t1 Successfully done binding with CPP GIC Server
Aug 25 21:43:56.442 mfwd_ipv4_hw/init 0/4/CPU0 t1 Successfully done binding with CPP GIC Server
Aug 25 21:43:56.444 mfwd_ipv4_hw/init 0/4/CPU0 t1 Successfully binded with CPP Rx Adjacency APIs Lib
Aug 25 21:43:56.445 mfwd_ipv4_hw/init 0/4/CPU0 t1 Successfully binded with CPP Tx Adjacency APIs Lib
Aug 25 21:43:56.445 mfwd_ipv4_hw/init 0/4/CPU0 t1 Successfully binded with CPP Tx Adjacency APIs Lib
Aug 25 21:43:56.445 mfwd_ipv4_hw/init 0/4/CPU0 t1 Initialized interface lib
Aug 25 21:43:56.464 mfwd_ipv4_hw/init 0/4/CPU0 t1 Initialized EDM backend
Aug 25 21:43:56.466 mfwd_ipv4_hw/init 0/4/CPU0 t1 Initialized utilities lib
Aug 25 21:43:56.471 mfwd_ipv4_hw/init 0/4/CPU0 t1 MFWD: Platform lib initializiation completed
Aug 25 21:43:58.412 mfwd_ipv4_hw/event 0/4/CPU0 t1 CPP Modify adj cpp 1 adj handle 0xa73e907c ifh 91 link 1 enctype 0 flags 1 hw addr 0x8c580000
Aug 25 21:43:58.412 mfwd_ipv4_hw/event 0/4/CPU0 t1 CPP Modify adj cpp 1 adj handle 0xa73e90c0 ifh 98 link 1 enctype 0 flags 1 hw addr 0x8c580010
Aug 26 22:25:50.253 mfwd_ipv4_hw/error 0/4/CPU0 t1 ===>> Proc started jid=227, pid=163930
Aug 26 22:25:50.253 mfwd_ipv4_hw/netio 0/4/CPU0 t1 ===>> Proc started jid=227, pid=163930
Aug 26 22:25:50.253 mfwd_ipv4_hw/fevent 0/4/CPU0 t1 ===>> Proc started jid=227, pid=163930
Aug 26 22:25:50.253 mfwd_ipv4_hw/event 0/4/CPU0 t1 ===>> Proc started jid=227, pid=163930
show mfib hardware resource-counters
To display the allocated and freed hardware resources for the Multicast Forwarding Information Base (MFIB) process, use the show mfib hardware resource-counters command in EXEC mode .
show mfib [ vrf vrf-name ] [ ipv4 | ipv6 ] hardware resource-counters location node-id
Syntax Description
|
vrf vrf-name |
(Optional) Specifies a VPN routing and forwarding (VRF) instance. |
|
ipv4 |
(Optional) Specifies IPv4 address prefixes. |
|
ipv6 |
(Optional) Specifies IPv6 address prefixes. |
|
location node-id |
Specifies an MFIB-designated node. |
Command Default
IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the show mfib hardware resource-counters command to understand the table lookup unit (TLU) resource usage by MFIB.
- Usage for each channel
- Storing of specific data
- Allocation counts for metro statistics
- Failure counts for metro statistics
Note | Use the location option in the show mfib hardware resource-counters command to indicate for which linecard you need information. The command will not display any useful output if only RSP is specified or if no location is specified. |
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read |
Examples
The following is a sample output from the show mfib hardware resource-counters command on the Cisco ASR 9000 Series SIP-700 line card:
RP/0/RSP0/CPU0:router# show mfib hardware resource-counters location 0/4/CPU0
LC Type: A9K-SIP-700
PD Memory Alloc/Free/In Use Stats:
--------------------------------------------------------
Type Allocated Freed In Use
--------------------------------------------------------
global 0 0 0
table extension 1 0 1
route extension 18 11 7
interface extension 18 10 8
idb extension 3 0 3
EDM bag data 26 24 2
vpn extension 0 0 0
mdt ea extension 0 0 0
--------------------------------------------------------
Ingress Hardware Resource Counters:
--------------------------------------------------------
Type Allocated Freed In Use
--------------------------------------------------------
prefix stats resource 18 11 7
PLU prefix resource 18 11 7
prefix replica resource 0 0 0
--------------------------------------------------------
Egress Hardware Resource Counters:
--------------------------------------------------------
Type Allocated Freed In Use
--------------------------------------------------------
prefix stats resource 18 11 7
PLU prefix resource 18 11 7
prefix replica resource 21 12 9
--------------------------------------------------------
Ingress Hardware Global Multicast Statistics:
--------------------------------------------------------
Punt Packets: 3
Punt Drop Packets: 0
Inject Packets: 0
Inject Drop Packets: 0
Drop Packets/Bytes: 0/0
--------------------------------------------------------
Egress Hardware Global Multicast Statistics:
--------------------------------------------------------
Punt Packets: 0
Punt Drop Packets: 0
Inject Packets: 0
Inject Drop Packets: 0
Drop Packets/Bytes: 0/0
--------------------------------------------------------
The following is a sample out put of show mfib hardware resource-counters command:
RP/0/RSP0/CPU0:router# show mfib hardware resource-counters location 0/0/CPU0
LC Type: Trident
prm_stat success calls: ingress: 4250,4092 egress: 0,0
prm_stat failure calls: ingress: 0,0 egress: 0,0
Memory alloc stats
-----------------------------------------------------
Type Allocated Freed Delta
-----------------------------------------------------
global 0 0 0
table extension 0 0 0
route extension 187 180 7
interface extension 221 215 6
idb extension 52 47 5
kmrs 159 159 0
kmrs key 652 652 0
kmrs result 488 488 0
uidb data 437 437 0
EDM bag data 5 3 2
-----------------------------------------------------
|
Field |
Description |
|---|---|
|
prm_stat success calls |
The number of successful calls to allocate and free statistics blocks, for ingress and egress statistics. |
|
prm_stat failure calls |
The number of failed calls to allocate and free statistics blocks, for ingress and egress statistics. |
|
Type |
Describes the structure type. |
|
Allocated |
The number of blocks allocated per structure type. |
|
Freed |
The number of blocks freed per structure type. |
|
Delta |
The difference between allocated and freed blocks per structure type. |
Related Commands
Command | Description |
| Displays interface-related information used during software multicast switching in the Multicast Forwarding Information Base (MFIB) process. |
show mfib hardware route accept-bitmap
To display platform-specific Multicast Forwarding Information Base (MFIB) information for the interface list that accepts bidirectional routes, use the show mfib hardware route accept-bitmap command in EXEC mode .
show mfib [ vrf vrf-name ] [ ipv4 | ipv6 ] hardware route accept-bitmap [*] [ group-address [ /prefix-length ] ] [detail] [ location node-id ]
Syntax Description
|
vrf vrf-name |
(Optional) Specifies a VPN routing and forwarding (VRF) instance. |
|
ipv4 |
(Optional) Specifies IPv4 address prefixes. |
|
ipv6 |
(Optional) Specifies IPv6 address prefixes. |
|
* |
(Optional) Displays shared tree entry. |
|
source-address |
(Optional) IP address or hostname of the multicast route source: |
|
group-address |
(Optional) IP address or hostname of the multicast group. |
|
/ prefix-length |
(Optional) Prefix length of the multicast group. A decimal value that indicates how many of the high-order contiguous bits of the address compose the prefix (the network portion of the address). A slash must precede the decimal value. |
|
detail |
(Optional) Detailed list of the routing database. |
|
location node-id |
(Optional) Specifies an MFIB-designated node. |
Command Default
IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Note | The command does not display any useful output if only RSP is specified or if no location is specified. |
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read |
Examples
The following is sample output from the show mfib hardware route accept-bitmap command:
RP/0RSP0/CPU0:RTP-VIKING-MCAST-04#show mfib hardware route accept-bitmap detail 227.0.0.0/8 location 0/2/cPU0
LC Type: Typhoon A9K-MOD80-SE
------------------------------------------------------------------------
Source: * Group: 227.0.0.0 Mask: 8 RPF Int: None
Accept bitmap summary (HW)
----------------------------------------------------
NP IIF Count Row Count
----------------------------------------------------
0 2 1
1 2 1
----------------------------------------------------
IIFs in Accept bitmap (HW)
----------------------------------------------------
NP: 0
----------------------------------------------------
Interface Ifhandle uIDB
----------------------------------------------------
GigabitEthernet0/2/0/16 0x080004c0 17
GigabitEthernet0/2/0/17 0x08000500 18
----------------------------------------------------
NP: 1
----------------------------------------------------
Interface Ifhandle uIDB
----------------------------------------------------
GigabitEthernet0/2/0/16 0x080004c0 17
GigabitEthernet0/2/0/17 0x08000500 18
----------------------------------------------------
----------------------------------------------------
Raw Accept bitmap (HW)
----------------------------------------------------
NP: 0 [Parent MLI: 305]
----------------------------------------------------
Key Bits 0 4 8 12
----------------------------------------------------
0x0000 2 00000600 00000000 00000000 00000000
----------------------------------------------------
NP: 1 [Parent MLI: 305]
----------------------------------------------------
Key Bits 0 4 8 12
----------------------------------------------------
0x0000 2 00000600 00000000 00000000 00000000
----------------------------------------------------
Related Commands
Command | Description |
| Displays interface-related information used during software multicast switching in the Multicast Forwarding Information Base (MFIB) process. |
show mfib hardware route internal
EXEC mode
.show mfib [ vrf vrf-name ] [ ipv4 | ipv6 ] hardware route internal [*] [source-address] [ group-address [ /prefix-length ] ] [detail] [ location node-id ]
Syntax Description
|
* |
(Optional) Displays shared tree entries. |
|
A.B.C.D |
(Optional) Source IP address or hostname of the MFIB route. |
|
A.B.C.D/length |
(Optional) Group IP address or hostname of the MFIB route and the prefix length. Prefix length of the MFIB group address is a decimal value that indicates how many of the high-order contiguous bits of the address compose the prefix (the network portion of the address). A slash must precede the decimal value. |
|
detail |
(Optional) Details of each route (requires 140 columns). |
|
location node-id |
(Optional) Specifies the MFIB location. |
|
ipv4 |
(Optional) Specifies IPv4 address prefixes. |
|
ipv6 |
(Optional) Specifies IPv6 address prefixes. |
Command Default
IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
|
Release 3.9.1 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Note | The command does not display any useful output if only RSP is specified or if no location is specified. |
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read |
Examples
The following example shows a sample output of the command:
RP/0/RSP0/CPU0:router# show mfib hardware route internal detail location 0/1/CPU0
LC Type: Trident
--------------------------------------------------------------------------
Legend:
Route Information - (Ingress)
NP: Network Processor, IC: BACL check, IP: Punt this packet to LC CPU,
ID: Directly connected, IS: RPF interface signal, IU: Punt copy to RP,
IF: Punt to LC CPU if forwarded, IM: Result match, IV: Valid entry,
IR: RPF IF, IA: Fabric slotmask, IG: Multicast group ID
Route Information - (Egress)
ET: Table ID to be used for OLIST lookup, EO: OLIST count bit,
ER: Route MGID to be used for OLIST/NRPF lookup, EM: Result match,
EV: Valid entry, EC: Count of OLIST members on this chip,
BS: Base of the statistics pointer
Route Information - (MDT)
TU: Tunnel Route, TE: Tunnel Encap, TD: Tunnel Decap,
CD: Conditional Decap, MI: MVET Index
MDT Encap Information
NP: Network Processor, UC: Use Customer ToS,
Csum: IP Checksum, TID: Table ID, UIDB: Tunnnel UIDB,
T-ifh: Tunnel Interface Handle, StatP: Tunnnel Stat Ptr,
CMG: Core Route Multicast Group ID, TMTU: Tunnnel MTU
Software Route Information (PD)
T: Tunnel Route, E: Encap, D: Decap, CD: Conditional Decap,
MVET-ID: MDT Encap Table ID, MVD: MVET Entry Dirty,
TUS: Tunnel UIDB Set, TID: Table ID, UIDB: Tunnnel UIDB
TMTU: Tunnnel MTU
--------------------------------------------------------------------------
Source: * Group: 224.0.0.0 Mask length: 4 RPF Int: None
Route Information
-----------------
------------------------------------------------------------------------------
N I I I I I I I I I I I E E E E E E B T T T
P C P D S U F M V R A G T O R M V C S U E D
------------------------------------------------------------------------------
0 T F T F F F T T 0x0 0x0 0x8080 0 F 3 T T 0 0x3640f F F F
1 T F T F F F T T 0x0 0x0 0x8080 0 F 3 T T 0 0x3640f F F F
2 T F T F F F T T 0x0 0x0 0x8080 0 F 3 T T 0 0x3640f F F F
3 T F T F F F T T 0x0 0x0 0x8080 0 F 3 T T 0 0x3640f F F F
Software Route Information (PD)
-------------------------------
T E D CD MVET-ID MVD TUS TID UIDB T-ifh TMTU
-----------------------------------------------------------
F F F F 0x0 F F 0x0 0x0 0x0 0
-----------------------------------------------------------
Source: * Group: 224.0.0.0 Mask length: 24 RPF Int: None
Route Information
-----------------
------------------------------------------------------------------------------
N I I I I I I I I I I I E E E E E E B T T T
P C P D S U F M V R A G T O R M V C S U E D
------------------------------------------------------------------------------
0 T F F F F F T T 0x0 0x0 0x8084 0 F 0 T T 0 0x36400 F F F
1 T F F F F F T T 0x0 0x0 0x8084 0 F 0 T T 0 0x36400 F F F
2 T F F F F F T T 0x0 0x0 0x8084 0 F 0 T T 0 0x36400 F F F
3 T F F F F F T T 0x0 0x0 0x8084 0 F 0 T T 0 0x36400 F F F
Software Route Information (PD)
-------------------------------
T E D CD MVET-ID MVD TUS TID UIDB T-ifh TMTU
-----------------------------------------------------------
F F F F 0x0 F F 0x0 0x0 0x0 0
-----------------------------------------------------------
Source: * Group: 224.0.1.39 Mask length: 32 RPF Int: None
Route Information
-----------------
------------------------------------------------------------------------------
N I I I I I I I I I I I E E E E E E B T T T
P C P D S U F M V R A G T O R M V C S U E D
------------------------------------------------------------------------------
0 F T F F F F T T 0x0 0x0 0x8085 0 F 1 T T 0 0x36405 F F F
1 F T F F F F T T 0x0 0x0 0x8085 0 F 1 T T 0 0x36405 F F F
2 F T F F F F T T 0x0 0x0 0x8085 0 F 1 T T 0 0x36405 F F F
3 F T F F F F T T 0x0 0x0 0x8085 0 F 1 T T 0 0x36405 F F F
Software Route Information (PD)
-------------------------------
T E D CD MVET-ID MVD TUS TID UIDB T-ifh TMTU
-----------------------------------------------------------
F F F F 0x0 F F 0x0 0x0 0x0 0
-----------------------------------------------------------
Source: * Group: 224.0.1.40 Mask length: 32 RPF Int: None
Route Information
-----------------
------------------------------------------------------------------------------
N I I I I I I I I I I I E E E E E E B T T T
P C P D S U F M V R A G T O R M V C S U E D
------------------------------------------------------------------------------
0 F T F F F F T T 0x0 0x0 0x8086 0 F 7 T T 0 0x36423 F F F
1 F T F F F F T T 0x0 0x0 0x8086 0 F 7 T T 0 0x36423 F F F
2 F T F F F F T T 0x0 0x0 0x8086 0 F 7 T T 0 0x36423 F F F
3 F T F F F F T T 0x0 0x0 0x8086 0 F 7 T T 0 0x36423 F F F
Software Route Information (PD)
-------------------------------
T E D CD MVET-ID MVD TUS TID UIDB T-ifh TMTU
-----------------------------------------------------------
F F F F 0x0 F F 0x0 0x0 0x0 0
-----------------------------------------------------------
Source: * Group: 232.0.0.0 Mask length: 8 RPF Int: None
Route Information
-----------------
------------------------------------------------------------------------------
N I I I I I I I I I I I E E E E E E B T T T
P C P D S U F M V R A G T O R M V C S U E D
------------------------------------------------------------------------------
0 T F F F F F T T 0x0 0x0 0x8087 0 F 2 T T 0 0x3640a F F F
1 T F F F F F T T 0x0 0x0 0x8087 0 F 2 T T 0 0x3640a F F F
2 T F F F F F T T 0x0 0x0 0x8087 0 F 2 T T 0 0x3640a F F F
3 T F F F F F T T 0x0 0x0 0x8087 0 F 2 T T 0 0x3640a F F F
Software Route Information (PD)
-------------------------------
T E D CD MVET-ID MVD TUS TID UIDB T-ifh TMTU
-----------------------------------------------------------
F F F F 0x0 F F 0x0 0x0 0x0 0
-----------------------------------------------------------
Source: * Group: 239.60.0.0 Mask length: 16 RPF Int: Gi0/1/
Route Information
-----------------
------------------------------------------------------------------------------
N I I I I I I I I I I I E E E E E E B T T T
P C P D S U F M V R A G T O R M V C S U E D
------------------------------------------------------------------------------
0 T F F F F F T T 0x2000500 0x0 0x8081 0 F 6 T T 0 0x3641e F F F
1 T F F F F F T T 0x2000500 0x0 0x8081 0 F 6 T T 0 0x3641e F F F
2 T F F F F F T T 0x2000500 0x0 0x8081 0 F 6 T T 0 0x3641e F F F
3 T F F F F F T T 0x2000500 0x0 0x8081 0 F 6 T T 0 0x3641e F F F
Software Route Information (PD)
-------------------------------
T E D CD MVET-ID MVD TUS TID UIDB T-ifh TMTU
-----------------------------------------------------------
F F F F 0x0 F F 0x0 0x0 0x0 0
-----------------------------------------------------------
Source: * Group: 239.60.60.60 Mask length: 32 RPF Int: None
Route Information
-----------------
------------------------------------------------------------------------------
N I I I I I I I I I I I E E E E E E B T T T
P C P D S U F M V R A G T O R M V C S U E D
------------------------------------------------------------------------------
0 T F F F F F T T 0x0 0x40 0x8089 0 F 5 T T 0 0x36419 F F F
1 T F F F F F T T 0x0 0x40 0x8089 0 F 5 T T 0 0x36419 F F F
2 T F F F F F T T 0x0 0x40 0x8089 0 F 5 T T 0 0x36419 F F F
3 T F F F F F T T 0x0 0x40 0x8089 0 F 5 T T 0 0x36419 F F F
Software Route Information (PD)
-------------------------------
T E D CD MVET-ID MVD TUS TID UIDB T-ifh TMTU
-----------------------------------------------------------
F F F F 0x0 F F 0x0 0x0 0x0 0
-----------------------------------------------------------
Source: * Group: 239.60.62.62 Mask length: 32 RPF Int: None
Route Information
-----------------
------------------------------------------------------------------------------
N I I I I I I I I I I I E E E E E E B T T T
P C P D S U F M V R A G T O R M V C S U E D
------------------------------------------------------------------------------
0 T F F F F F T T 0x0 0x40 0x8088 0 F 4 T T 0 0x36414 F F F
1 T F F F F F T T 0x0 0x40 0x8088 0 F 4 T T 0 0x36414 F F F
2 T F F F F F T T 0x0 0x40 0x8088 0 F 4 T T 0 0x36414 F F F
3 T F F F F F T T 0x0 0x40 0x8088 0 F 4 T T 0 0x36414 F F F
Software Route Information (PD)
-------------------------------
T E D CD MVET-ID MVD TUS TID UIDB T-ifh TMTU
-----------------------------------------------------------
F F F F 0x0 F F 0x0 0x0 0x0 0
-----------------------------------------------------------
Source: * Group: 239.60.64.64 Mask length: 32 RPF Int: None
Route Information
-----------------
------------------------------------------------------------------------------
N I I I I I I I I I I I E E E E E E B T T T
P C P D S U F M V R A G T O R M V C S U E D
------------------------------------------------------------------------------
0 T F F F F F T T 0x0 0x2 0x8082 0 F 8 T T 0 0x36428 F F F
1 T F F F F F T T 0x0 0x2 0x8082 1 T 8 T T 1 0x36428 F F F
2 T F F F F F T T 0x0 0x2 0x8082 0 F 8 T T 0 0x36428 F F F
3 T F F F F F T T 0x0 0x2 0x8082 0 F 8 T T 0 0x36428 F F F
Software Route Information (PD)
-------------------------------
T E D CD MVET-ID MVD TUS TID UIDB T-ifh TMTU
-----------------------------------------------------------
F F F F 0x0 F F 0x0 0x0 0x0 0
-----------------------------------------------------------
Source: * Group: 239.60.66.66 Mask length: 32 RPF Int: None
Route Information
-----------------
------------------------------------------------------------------------------
N I I I I I I I I I I I E E E E E E B T T T
P C P D S U F M V R A G T O R M V C S U E D
------------------------------------------------------------------------------
0 T F F F F F T T 0x0 0x2 0x8083 0 F 9 T T 0 0x3642d F F F
1 T F F F F F T T 0x0 0x2 0x8083 1 T 9 T T 1 0x3642d F F F
2 T F F F F F T T 0x0 0x2 0x8083 0 F 9 T T 0 0x3642d F F F
3 T F F F F F T T 0x0 0x2 0x8083 0 F 9 T T 0 0x3642d F F F
Software Route Information (PD)
-------------------------------
T E D CD MVET-ID MVD TUS TID UIDB T-ifh TMTU
-----------------------------------------------------------
F F F F 0x0 F F 0x0 0x0 0x0 0
-----------------------------------------------------------
show mfib hardware route location
EXEC mode
.show mfib [ vrf vrf-name ] [ ipv4 | ipv6 ] [*] [source-address] [ group-address [ /prefix-length ] ] location node-id
Syntax Description
|
vrf vrf-name |
(Optional) Specifies a VPN routing and forwarding (VRF) instance. |
|
ipv4 |
(Optional) Specifies IPv4 address prefixes. |
|
ipv6 |
(Optional) Specifies IPv6 address prefixes. |
|
(Optional) Displays shared tree entry. |
|
|
source-address |
(Optional) IP address or hostname of the multicast route source. |
|
group-address |
(Optional) IP address or hostname of the multicast group. |
|
/ prefix-length |
(Optional) Prefix length of the multicast group. A decimal value that indicates how many of the high-order contiguous bits of the address compose the prefix (the network portion of the address). A slash must precede the decimal value. |
|
node-id |
Node ID for an MFIB-designated node. |
Command Default
IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
| Release 5.0.0 |
This command was introduced. |
Usage Guidelines
Note | The command does not display any useful output if only RSP is specified or if no location is specified. |
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read |
Examples
The following is sample output from the show mfib hardware route location command:
RP/0/RSP0CPU0:RTP-VIKING-MCAST-04#show mfib hardware route detail 227.0.0.0/8 location 0/2/cPU0
LC Type: Typhoon A9K-MOD80-SE
--------------------------------------------------------------------------
Legend:
Route Information
NP: NP ID B: BACL check
S: RPF Interface signal DC: Directly connected
PL: Punt to LC CPU PR: Punt to RP
PF: Punt if forwarded DR: Drop all
RI: RPF interface T: Table ID for lookup
OC: Count of OLIST members MF: MoFRR enabled
TR: Tunnel Route TE: Tunnel Encap
TD: Tunnel Decap CD: Conditional Decap
MI: MVET index Base: Base of the statistics pointer
NI: Not Installed BD: Bidir
MVPN Information
MLI: MVPN table index VTID: VRF Table ID
RPFID: RPF Identifier TUS: Tunnel uIDB set
MVD: MVET entry dirty NP: NP ID
TStat: Tunnel stat pointer TUIDB: Tunnel uIDB
TIFH: Tunnel Interface handle
MoFRR Information
MLI: Multicast leaf index A: Active RPF interface
RI: RPF interface (or RPF ID) WDI: Watchdog counter index
--------------------------------------------------------------------------
Source: * Group: 227.0.0.0 Mask: 8 RPF Int: None
MGID: 17178 MLI: 305 Fabric Slotmask: 0x10 FGID: 0x10
Parent MLI: 305 IIF Count: 2 AB Rows: 1
Route Information
---------------------------------------------------------------------------
NP B S DC PL PR PF DR BD RI T OC MF TR TE TD CD MI Base
---------------------------------------------------------------------------
0 F F F F F F F T 0x0 0 1 F F F F F 0x0 0x5302ed
1 F F F F F F F T 0x0 0 0 F F F F F 0x0 0x530106
---------------------------------------------------------------------------
Software MGID Information
----------------------------------------------------
MGID: 17178 Mask: 0x1 Old MGID: 0 Old Mask: 0x1
----------------------------------------------------
Related Commands
Command | Description |
| Displays route entries in the Multicast Forwarding Information Base (MFIB). |
show mfib hardware route mofrr
EXEC mode
.show mfib hardware route mofrr { [*] | [source-address] [ group-address [ /prefix-length ] ] [detail] } [ location node-id ]
Syntax Description
|
* |
(Optional) Displays all the MoFRR routes configured in the platform. |
|
source-address |
(Optional) IP address or hostname of the multicast route source. |
|
group-address |
(Optional) IP address or hostname of the multicast group. |
|
detail |
(Optional) Displays a detailed list of the MoFRR routing database. |
|
location node-id |
Specifies the Node ID for an MFIB-designated node. |
Command Default
IPv4 addressing is the default. Currently, MoFRR supports only IPv4 routes.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
|
Release 3.9.0 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
MoFRR is a mechanism in which two copies of the same multicast stream flow through disjoint paths in the network. At the point in the network (usually the PE closer to the receivers) where the two streams merge, one of the streams is accepted and forwarded on the downstream links, while the other stream is discarded. When a failure is detected in the primary stream due to a link or node failure in the network, MoFRR instructs the forwarding plane to start accepting packets from the backup stream (which now becomes the primary stream).
MoFRR is triggered when the hardware detects traffic loss on the primary path of a given flow or route. Traffic loss is defined as no data packet having been received for 30 ms. When MoFRR is triggered, the primary and secondary reverse-path forwarding (RPF) interfaces are exposed to the forwarding plane and switchover occurs entirely at the hardware level.
The show mfib hardware route mofrr command displays the output MoFRR route list of the platform. If there is no MoFRR route enabled in the platform, then the output result is “There are no MoFRR routes configured”.
The command does not display any useful output if only RSP is specified or if no location is specified.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read |
Examples
The following is a sample output from the show mfib hardware route mofrr command:
RP/0/RSP0/CPU0:router# show mfib hardware route mofrr location 0/0/cpu0
LC Type: Trident
--------------------------------------------------------------------------
Legend:
Route MoFRR Information
A: Active RPF interface, MS: Monitoring State,
WDI: Watchdog Count Index, NP: Network Processor,
--------------------------------------------------------------------------
Source: 20.20.20.1 Group: 225.0.0.1 Mask length: 64 RPF Int: Gi0/0/0/8
-----------------------------------------------------
RPFS Interface A MS WDI
-----------------------------------------------------
Primary: Gi0/0/0/8 T 2 1846768
Backup: Gi0/0/0/18 F 0 1846769
-----------------------------------------------------
OIFS
---------------
NP Intf
---------------
1 Gi0/0/0/28
---------------
Sequence num: 1 Num of switchovers: 0
WatchDog Counters:
-----------------------------------------------------------
NP Profile Valid Current-Cnt Last-cnt
-----------------------------------------------------------
Prim WDC 0 0 0 3848 12
Prim WDC 1 0 0 3848 12
Prim WDC 2 0 0 3848 12
Prim WDC 3 1 1 3848 12
Back WDC 0 0 0 3848 12
Back WDC 1 0 0 3848 12
Back WDC 2 0 0 3848 12
Back WDC 3 0 0 3848 12
-----------------------------------------------------------
MoFRR Statistics:
-----------------------------------------------------------
NP Prim pkt rx Back pkt rx Interrupts Punts
-----------------------------------------------------------
0 0 0 0 0
1 0 0 0 0
2 0 0 0 0
3 406213 0 1 1
-----------------------------------------------------------
Source: 20.20.20.1 Group: 225.0.0.2 Mask length: 64 RPF Int: Gi0/0/0/8
-----------------------------------------------------
RPFS Interface A MS WDI
-----------------------------------------------------
Primary: Gi0/0/0/8 T 2 1846770
Backup: Gi0/0/0/18 F 0 1846771
-----------------------------------------------------
OIFS
---------------
NP Intf
---------------
1 Gi0/0/0/28
---------------
Sequence num: 1 Num of switchovers: 0
WatchDog Counters:
-----------------------------------------------------------
NP Profile Valid Current-Cnt Last-cnt
-----------------------------------------------------------
Prim WDC 0 0 0 3848 12
Prim WDC 1 0 0 3848 12
Prim WDC 2 0 0 3848 12
Prim WDC 3 1 1 3848 12
Back WDC 0 0 0 3848 12
Back WDC 1 0 0 3848 12
Back WDC 2 0 0 3848 12
Back WDC 3 0 0 3848 12
-----------------------------------------------------------
MoFRR Statistics:
-----------------------------------------------------------
NP Prim pkt rx Back pkt rx Interrupts Punts
-----------------------------------------------------------
0 0 0 0 0
1 0 0 0 0
2 0 0 0 0
3 406212 0 1 1
-----------------------------------------------------------
The following is sample output from the show mfib hardware route MoFRR command with only one multicast group:
RP/0/RSP0/CPU0:router# show mfib hardware route mofrr 225.0.0.1 location 0/0/CPU0
LC Type: Trident
--------------------------------------------------------------------------
Legend:
Route MoFRR Information
A: Active RPF interface, MS: Monitoring State,
WDI: Watchdog Count Index, NP: Network Processor,
--------------------------------------------------------------------------
Source: 20.20.20.1 Group: 225.0.0.1 Mask length: 64 RPF Int: Gi0/0/0/8
-----------------------------------------------------
RPFS Interface A MS WDI
-----------------------------------------------------
Primary: Gi0/0/0/8 T 2 1846772
Backup: Gi0/0/0/18 F 0 1846773
-----------------------------------------------------
OIFS
---------------
NP Intf
---------------
1 Gi0/0/0/28
---------------
Sequence num: 1 Num of switchovers: 0
WatchDog Counters:
-----------------------------------------------------------
NP Profile Valid Current-Cnt Last-cnt
-----------------------------------------------------------
Prim WDC 0 0 0 3848 12
Prim WDC 1 0 0 3848 12
Prim WDC 2 0 0 3848 12
Prim WDC 3 1 1 3848 12
Back WDC 0 0 0 3848 12
Back WDC 1 0 0 3848 12
Back WDC 2 0 0 3848 12
Back WDC 3 0 0 3848 12
-----------------------------------------------------------
MoFRR Statistics:
-----------------------------------------------------------
NP Prim pkt rx Back pkt rx Interrupts Punts
-----------------------------------------------------------
0 0 0 0 0
1 0 0 0 0
2 0 0 0 0
3 400465 0 1 1
-----------------------------------------------------------
The following is sample output from the show mfib hardware route MoFRR command with only one multicast source:
RP/0/RSP0/CPU0:router# show mfib hardware route mofrr 20.20.20.1 location 0/0/CPU0
LC Type: Trident
--------------------------------------------------------------------------
Legend:
Route MoFRR Information
A: Active RPF interface, MS: Monitoring State,
WDI: Watchdog Count Index, NP: Network Processor,
--------------------------------------------------------------------------
Source: 20.20.20.1 Group: 225.0.0.1 Mask length: 64 RPF Int: Gi0/0/0/8
-----------------------------------------------------
RPFS Interface A MS WDI
-----------------------------------------------------
Primary: Gi0/0/0/8 T 2 1846772
Backup: Gi0/0/0/18 F 0 1846773
-----------------------------------------------------
OIFS
---------------
NP Intf
---------------
1 Gi0/0/0/28
---------------
Sequence num: 1 Num of switchovers: 0
WatchDog Counters:
-----------------------------------------------------------
NP Profile Valid Current-Cnt Last-cnt
-----------------------------------------------------------
Prim WDC 0 0 0 3848 12
Prim WDC 1 0 0 3848 12
Prim WDC 2 0 0 3848 12
Prim WDC 3 1 1 3848 12
Back WDC 0 0 0 3848 12
Back WDC 1 0 0 3848 12
Back WDC 2 0 0 3848 12
Back WDC 3 0 0 3848 12
-----------------------------------------------------------
MoFRR Statistics:
-----------------------------------------------------------
NP Prim pkt rx Back pkt rx Interrupts Punts
-----------------------------------------------------------
0 0 0 0 0
1 0 0 0 0
2 0 0 0 0
3 0 0 1 1
-----------------------------------------------------------
Source: 20.20.20.1 Group: 225.0.0.2 Mask length: 64 RPF Int: Gi0/0/0/8
-----------------------------------------------------
RPFS Interface A MS WDI
-----------------------------------------------------
Primary: Gi0/0/0/8 T 2 1846774
Backup: Gi0/0/0/18 F 0 1846775
-----------------------------------------------------
OIFS
---------------
NP Intf
---------------
1 Gi0/0/0/28
---------------
Sequence num: 1 Num of switchovers: 0
WatchDog Counters:
-----------------------------------------------------------
NP Profile Valid Current-Cnt Last-cnt
-----------------------------------------------------------
Prim WDC 0 0 0 3848 12
Prim WDC 1 0 0 3848 12
Prim WDC 2 0 0 3848 12
Prim WDC 3 1 1 3848 12
Back WDC 0 0 0 3848 12
Back WDC 1 0 0 3848 12
Back WDC 2 0 0 3848 12
Back WDC 3 0 0 3848 12
-----------------------------------------------------------
MoFRR Statistics:
-----------------------------------------------------------
NP Prim pkt rx Back pkt rx Interrupts Punts
-----------------------------------------------------------
0 0 0 0 0
1 0 0 0 0
2 0 0 0 0
3 0 0 1 1
-----------------------------------------------------------
|
Field |
Description |
|---|---|
|
RPFS |
Primary and backup RPF of the route. |
|
A |
Currently active RPF for forwarding the traffic to the egress (OLIST). T: means true, F: means false. |
|
MS |
Monitoring state. It has three states. MS=0, indicates that the monitoring state disabled. MS=1, indicates that active RPF is monitoring traffic activity. MS=2, indicates that active RPF is monitoring traffic loss. |
|
WDI |
Watchdog Count Index. Each MoFRR route has two Line card specific watchdog indexes, associated with primary and backup RPF, respectively. |
|
OIFS |
Output Interfaces in the local line card. |
|
Sequence num |
MoFRR specific route sequence number. |
|
Num of switchovers |
Total number of switchovers triggered by traffic loss detection in the data plane. |
|
Watchdog Counters |
Internal Hardware watchdog counters |
|
MoFRR Statistics |
Internal software watchdog counters |
If there is no MoFRR route enabled in the platform, the output result will be as follows:
RP/0/RSP0/CPU0:router# show mfib hardware route mofrr location 0/0/CPU0
LC Type: Trident
No matching routes in MFIB
There are no MoFRR routes configured.
Related Commands
Command | Description |
| Displays platform-specific Multicast Forwarding Information Base (MFIB) information in the output interface list (olist) stored in the hardware. |
| Displays platform-specific Multicast Forwarding Information Base (MFIB) information for the packet and byte counters for each route. |
| Displays summary platform-specific Multicast Forwarding Information Base (MFIB) hardware information for each route entry. |
| Displays route entries in the Multicast Forwarding Information Base (MFIB). |
| Displays all entries in the Multicast Routing Information Base (MRIB). |
show mfib hardware route olist
To display platform-specific Multicast Forwarding Information Base (MFIB) information in the output interface list (olist) stored in the hardware, use the show mfib hardware route olist command in the appropriate mode.
show mfib [ vrf vrf-name ] [ ipv4 | ipv6 ] hardware route olist { [*] | [source-address] [ group-address [ /prefix-length ] ] } [ location node-id ]
Syntax Description
|
vrf vrf-name |
(Optional) Specifies a VPN routing and forwarding (VRF) instance. |
|
ipv4 |
(Optional) Specifies IPv4 address prefixes. |
|
ipv6 |
(Optional) Specifies IPv6 address prefixes. |
|
* |
(Optional) Displays shared tree entries. |
|
source-address |
(Optional) IP address or hostname of the multicast route source. |
|
group-address |
(Optional) IP address or hostname of the multicast group. |
|
/ prefix-length |
(Optional) Prefix length of the multicast group. A decimal value that indicates how many of the high-order contiguous bits of the address compose the prefix (the network portion of the address). A slash must precede the decimal value. |
|
location node-id |
Specifies an MFIB-designated node. |
Command Default
IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The show mfib hardware route olist command displays the output interface list (olist) for each route. The Multicast Forwarding (MFWD) process stores olist interfaces in a table lookup unit (TLU) block (in groups of three). As such, the command displays each route three times. The command does not display any useful output if only RSP is specified or if no location is specified.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read |
Examples
The following is sample output from the show mfib hardware route olist command. (The output fields are described in the header.)
RP/0/RSP0/CPU0:router# show mfib hardware route olist location 0/0/CPU0 LC Type: Trident -------------------------------------------------------------------------- Legend: Route Information - (Ingress) C: Chip ID, IC: BACL check, IP: Punt this packet to LC CPU, ID: Directly connected, IS: RPF interface signal, IU: Punt copy to RP, IF: Punt to LC CPU if forwarded, IM: Result match, IV: Valid entry, IR: RPF IF, IA: Fabric slotmask, IG: Multicast group ID Route Information - (Egress) ET: Table ID to be used for OLIST lookup, EO: OLIST count bit, ER: Route MGID to be used for OLIST/NRPF lookup, EM: Result match, EV: Valid entry, EC: Count of OLIST members on this chip, BS: Base of the statistics pointer Hardware Information C: Chip ID; T: Table ID; M: Member ID; Intf: Interface, U: uIDB index, I: HW IC flag, B: HW BACL bit, Base: Base of statistics pointer -------------------------------------------------------------------------- Source: * Group: 224.0.0.0 Mask length: 24 Route Information ---------------------------------------------------------------------------------- C IC IP ID IS IU IF IM IV IR IA IG ET EO ER EM EV EC BS ---------------------------------------------------------------------------------- 0 T F F F F F T T 0x0 0x0 0x8002 0 F 2 T T 0 0x5516c 1 T F F F F F T T 0x0 0x0 0x8002 0 F 2 T T 0 0x5516c 2 T F F F F F T T 0x0 0x0 0x8002 0 F 2 T T 0 0x5516c 3 T F F F F F T T 0x0 0x0 0x8002 0 F 2 T T 0 0x555a4 ---------------------------------------------------------------------------------- Source: * Group: 224.0.1.39 Mask length: 32 Route Information ---------------------------------------------------------------------------------- C IC IP ID IS IU IF IM IV IR IA IG ET EO ER EM EV EC BS ---------------------------------------------------------------------------------- 0 F T F F F F T T 0x0 0x0 0x8000 0 F 0 T T 0 0x55162 1 F T F F F F T T 0x0 0x0 0x8000 0 F 0 T T 0 0x55162 2 F T F F F F T T 0x0 0x0 0x8000 0 F 0 T T 0 0x55162 3 F T F F F F T T 0x0 0x0 0x8000 0 F 0 T T 0 0x5559a ---------------------------------------------------------------------------------- Source: * Group: 224.0.1.40 Mask length: 32 Route Information ---------------------------------------------------------------------------------- C IC IP ID IS IU IF IM IV IR IA IG ET EO ER EM EV EC BS ---------------------------------------------------------------------------------- 0 F T F F F F T T 0x0 0x0 0x8001 0 F 1 T T 0 0x55167 1 F T F F F F T T 0x0 0x0 0x8001 0 F 1 T T 0 0x55167 2 F T F F F F T T 0x0 0x0 0x8001 0 F 1 T T 0 0x55167 3 F T F F F F T T 0x0 0x0 0x8001 0 F 1 T T 0 0x5559f ---------------------------------------------------------------------------------- Source: * Group: 227.0.0.0 Mask length: 16 Route Information ---------------------------------------------------------------------------------- C IC IP ID IS IU IF IM IV IR IA IG ET EO ER EM EV EC BS ---------------------------------------------------------------------------------- 0 T F F F F F T T 0x280 0x0 0x8009 0 F 6 T T 0 0x55199 1 T F F F F F T T 0x280 0x0 0x8009 0 F 6 T T 0 0x55199 2 T F F F F F T T 0x280 0x0 0x8009 0 F 6 T T 0 0x55199 3 T F F F F F T T 0x280 0x0 0x8009 0 F 6 T T 0 0x555d1 ---------------------------------------------------------------------------------- Source: * Group: 227.0.0.1 Mask length: 32 Route Information ---------------------------------------------------------------------------------- C IC IP ID IS IU IF IM IV IR IA IG ET EO ER EM EV EC BS ---------------------------------------------------------------------------------- 0 T F F F F F T T 0x0 0x1 0x8004 0 F 5 T T 0 0x55185 1 T F F F F F T T 0x0 0x1 0x8004 0 F 5 T T 0 0x55185 2 T F F F F F T T 0x0 0x1 0x8004 0 F 5 T T 0 0x55185 3 T F F F F F T T 0x0 0x1 0x8004 1 T 5 T T 3 0x555bd ---------------------------------------------------------------------------------- Interface Information ----------------------------------------------------- C T M Intf U I B Base ----------------------------------------------------- 3 1 0 Gi0/0/0/8 9 F F 0x5540c 3 1 1 Gi0/0/0/4 5 F F 0x5540f 3 1 2 Gi0/0/0/6 7 F F 0x55412 ----------------------------------------------------- Source: * Group: 230.0.0.0 Mask length: 8 Route Information ---------------------------------------------------------------------------------- C IC IP ID IS IU IF IM IV IR IA IG ET EO ER EM EV EC BS ---------------------------------------------------------------------------------- 0 T F T F F F T T 0x0 0x0 0x8005 0 F 4 T T 0 0x55176 1 T F T F F F T T 0x0 0x0 0x8005 0 F 4 T T 0 0x55176 2 T F T F F F T T 0x0 0x0 0x8005 0 F 4 T T 0 0x55176 3 T F T F F F T T 0x0 0x0 0x8005 0 F 4 T T 0 0x555ae ---------------------------------------------------------------------------------- Source: * Group: 232.0.0.0 Mask length: 8 Route Information ---------------------------------------------------------------------------------- C IC IP ID IS IU IF IM IV IR IA IG ET EO ER EM EV EC BS ---------------------------------------------------------------------------------- 0 T F F F F F T T 0x0 0x0 0x8003 0 F 3 T T 0 0x55171 1 T F F F F F T T 0x0 0x0 0x8003 0 F 3 T T 0 0x55171 2 T F F F F F T T 0x0 0x0 0x8003 0 F 3 T T 0 0x55171 3 T F F F F F T T 0x0 0x0 0x8003 0 F 3 T T 0 0x555a9 ---------------------------------------------------------------------------------- Source: * Group: 233.1.0.0 Mask length: 16 Route Information ---------------------------------------------------------------------------------- C IC IP ID IS IU IF IM IV IR IA IG ET EO ER EM EV EC BS ---------------------------------------------------------------------------------- 0 T F F F F F T T 0x180 0x0 0x8007 0 F 7 T T 0 0x5518f 1 T F F F F F T T 0x180 0x0 0x8007 0 F 7 T T 0 0x5518f 2 T F F F F F T T 0x180 0x0 0x8007 0 F 7 T T 0 0x5518f 3 T F F F F F T T 0x180 0x0 0x8007 0 F 7 T T 0 0x555c7 ---------------------------------------------------------------------------------- Source: * Group: 233.4.0.0 Mask length: 16 Route Information ---------------------------------------------------------------------------------- C IC IP ID IS IU IF IM IV IR IA IG ET EO ER EM EV EC BS ---------------------------------------------------------------------------------- 0 T F F F F F T T 0x180 0x0 0x8008 0 F 8 T T 0 0x55194 1 T F F F F F T T 0x180 0x0 0x8008 0 F 8 T T 0 0x55194 2 T F F F F F T T 0x180 0x0 0x8008 0 F 8 T T 0 0x55194 3 T F F F F F T T 0x180 0x0 0x8008 0 F 8 T T 0 0x555cc ---------------------------------------------------------------------------------- RP/0/RSP0/CPU0:router# show mfib hardware route olist location 0/4/CPU0 LC Type: A9K-SIP-700 Header : Hardware Route Information Source : Source address Group : Group Address M : Mask Length C : Directly connected check flag RPF : Accepting interface for non-bidir entries S : Signal if packet arrived on RPF interface IC : Aggregated Internal copy flag PR : Punt to RP flag for Internal copy in the Loopback interface PK : PEEK flag FGID : Fabric Group ID MGID : Multicast Group ID PAL Olist : PAL Olist handle CPP Olist : CPP Olist handle Num OCE : Number of OCE entries Header : Route OCE Entry Information Interface : Interface name Handle : Interface handle IC : Internal copy flag Accept : Accept flag NS : Negate Signal flag F/EG : Forwarding flag Hardware Route Information ---------------------------------------------------------- Source |Group |M |C|RPF |S|IC|PR|PK|FGID |MGID |PAL Olist Handle|CPP OLIST Handle|Num OCE| ---------------------------------------------------------- * |224.0.0.0 |4 |T|Null |F| F| F|F |0 |16964|0xa6039538 |0x9dc8688c |0 | Ingress CPP Prefix Information ---------------------------------------------------------- === QFP Multicast prefix info === Root: a60394c4, Flags: 2 First leaf: 0 Number of nodes: 0x000001, leaves: 00000000 RPF i/f: 00000000 RPF Fast Convergence flags: 00000000 Secondary RPF: 00000000 RPF Fast Convergence timer: 0 ext_leaf: 0x8b900100 Egress CPP Prefix Information ---------------------------------------------------------- === QFP Multicast prefix info === Root: a60394c4, Flags: 2 First leaf: 0 Number of nodes: 0x000001, leaves: 00000000 RPF i/f: 00000000 RPF Fast Convergence flags: 00000000 Secondary RPF: 00000000 RPF Fast Convergence timer: 0 ext_leaf: 0x8ce80100 Route OCE Entry Information Route OLIST Information ---------------------------------------------------------- TREE .. : root : a60394c4 num_nodes 1 num_leaves 0 (in cp) Node: a60394c4 num_child:0 cum[wt:0 free:7] (in cpp) Node : 0x8d080060 flags : 0x4 child[0]: [NULL] child[1]: [NULL] child[2]: [NULL] child[3]: [NULL] child[4]: [NULL] child[5]: [NULL] child[6]: [NULL] Route Rx Adjacency Information ---------------------------------------------------------- OCE RX Adj Data for 0x8bb00000: base: 39(CPP HW RX ADJ IPV4 MCAST) adj_flags: 0x0 pd_16: 0x0 pd_32: 0x4244 output_uidb: 0x1fab counters_ptr: 0x893f5c30 byte count: 0 packet count: 0 Hardware Route Information ---------------------------------------------------------- Source |Group |M |C|RPF |S|IC|PR|PK|FGID |MGID |PAL Olist Handle|CPP OLIST Handle|Num OCE| ---------------------------------------------------------- * |224.0.0.0 |24 |F|Null |F| F| F|F |0 |16962|0x9e07d2e4 |0x9dc86924 |0 | Ingress CPP Prefix Information ---------------------------------------------------------- === QFP Multicast prefix info === Root: 9e07d270, Flags: 0 First leaf: 0 Number of nodes: 0x000001, leaves: 00000000 RPF i/f: 00000000 RPF Fast Convergence flags: 00000000 Secondary RPF: 00000000 RPF Fast Convergence timer: 0 ext_leaf: 0x8b900180 Egress CPP Prefix Information ---------------------------------------------------------- === QFP Multicast prefix info === Root: 9e07d270, Flags: 0 First leaf: 0 Number of nodes: 0x000001, leaves: 00000000 RPF i/f: 00000000 RPF Fast Convergence flags: 00000000 Secondary RPF: 00000000 RPF Fast Convergence timer: 0 ext_leaf: 0x8ce80180 Route OCE Entry Information Route OLIST Information ---------------------------------------------------------- TREE .. : root : 9e07d270 num_nodes 1 num_leaves 0 (in cp) Node: 9e07d270 num_child:0 cum[wt:0 free:7] (in cpp) Node : 0x8d080120 flags : 0x4 child[0]: [NULL] child[1]: [NULL] child[2]: [NULL] child[3]: [NULL] child[4]: [NULL] child[5]: [NULL] child[6]: [NULL] Route Rx Adjacency Information ---------------------------------------------------------- OCE RX Adj Data for 0x8bb00120: base: 39(CPP HW RX ADJ IPV4 MCAST) adj_flags: 0x0 pd_16: 0x0 pd_32: 0x4242 output_uidb: 0x1fab counters_ptr: 0x893f5c10 byte count: 0 packet count: 0 Hardware Route Information ---------------------------------------------------------- Source |Group |M |C|RPF |S|IC|PR|PK|FGID |MGID |PAL Olist Handle|CPP OLIST Handle|Num OCE| ---------------------------------------------------------- * |224.0.1.39|32 |F|Null |T| F| F|F |0 |16960|0x9e07d678 |0x9dc86970 |0 | Ingress CPP Prefix Information ---------------------------------------------------------- === QFP Multicast prefix info === Root: 9e07d604, Flags: 1 First leaf: 0 Number of nodes: 0x000001, leaves: 00000000 RPF i/f: 00000000 RPF Fast Convergence flags: 00000000 Secondary RPF: 00000000 RPF Fast Convergence timer: 0 ext_leaf: 0x8b9001c0 Egress CPP Prefix Information ---------------------------------------------------------- === QFP Multicast prefix info === Root: 9e07d604, Flags: 1 First leaf: 0 Number of nodes: 0x000001, leaves: 00000000 RPF i/f: 00000000 RPF Fast Convergence flags: 00000000 Secondary RPF: 00000000 RPF Fast Convergence timer: 0 ext_leaf: 0x8ce801c0 Route OCE Entry Information Route OLIST Information ---------------------------------------------------------- TREE .. : root : 9e07d604 num_nodes 1 num_leaves 0 (in cp) Node: 9e07d604 num_child:0 cum[wt:0 free:7] (in cpp) Node : 0x8d080140 flags : 0x4 child[0]: [NULL] child[1]: [NULL] child[2]: [NULL] child[3]: [NULL] child[4]: [NULL] child[5]: [NULL] child[6]: [NULL] Route Rx Adjacency Information ---------------------------------------------------------- OCE RX Adj Data for 0x8bb000f0: base: 39(CPP HW RX ADJ IPV4 MCAST) adj_flags: 0x0 pd_16: 0x0 pd_32: 0x4240 output_uidb: 0x1fab counters_ptr: 0x893f5c00 byte count: 0 packet count: 0 Hardware Route Information ---------------------------------------------------------- Source |Group |M |C|RPF |S|IC|PR|PK|FGID |MGID |PAL Olist Handle|CPP OLIST Handle|Num OCE| ---------------------------------------------------------- * |224.0.1.40|32 |F|Null |T| F| F|F |0 |16961|0x9dcbdab4 |0x9dc869bc |0 | Ingress CPP Prefix Information ---------------------------------------------------------- === QFP Multicast prefix info === Root: 9dcbda40, Flags: 1 First leaf: 0 Number of nodes: 0x000001, leaves: 00000000 RPF i/f: 00000000 RPF Fast Convergence flags: 00000000 Secondary RPF: 00000000 RPF Fast Convergence timer: 0 ext_leaf: 0x8b9000c0 Egress CPP Prefix Information ---------------------------------------------------------- === QFP Multicast prefix info === Root: 9dcbda40, Flags: 1 First leaf: 0 Number of nodes: 0x000001, leaves: 00000000 RPF i/f: 00000000 RPF Fast Convergence flags: 00000000 Secondary RPF: 00000000 RPF Fast Convergence timer: 0 ext_leaf: 0x8ce800c0 Route OCE Entry Information Route OLIST Information ---------------------------------------------------------- TREE .. : root : 9dcbda40 num_nodes 1 num_leaves 0 (in cp) Node: 9dcbda40 num_child:0 cum[wt:0 free:7] (in cpp) Node : 0x8d0800c0 flags : 0x4 child[0]: [NULL] child[1]: [NULL] child[2]: [NULL] child[3]: [NULL] child[4]: [NULL] child[5]: [NULL] child[6]: [NULL] Route Rx Adjacency Information ---------------------------------------------------------- OCE RX Adj Data for 0x8bb00040: base: 39(CPP HW RX ADJ IPV4 MCAST) adj_flags: 0x0 pd_16: 0x0 pd_32: 0x4241 output_uidb: 0x1fab counters_ptr: 0x893f5c40 byte count: 0 packet count: 0 Hardware Route Information ---------------------------------------------------------- Source |Group |M |C|RPF |S|IC|PR|PK|FGID |MGID |PAL Olist Handle|CPP OLIST Handle|Num OCE| ---------------------------------------------------------- * |225.0.0.0 |32 |T|Se0/4/0/0/1|F| F| F|F |64 |17013|0x9dcbd5a4 |0x9dc86a08 |2 | Ingress CPP Prefix Information ---------------------------------------------------------- === QFP Multicast prefix info === Root: 9dcbd530, Flags: 2 First leaf: 9dcbd9bc Number of nodes: 0x000001, leaves: 0x000001 RPF i/f: 0x007fff RPF Fast Convergence flags: 00000000 Secondary RPF: 00000000 RPF Fast Convergence timer: 0 ext_leaf: 0x8b900080 Egress CPP Prefix Information ---------------------------------------------------------- === QFP Multicast prefix info === Root: 9dcbd530, Flags: 2 First leaf: 9dcbd9bc Number of nodes: 0x000001, leaves: 0x000001 RPF i/f: 0x007fff RPF Fast Convergence flags: 00000000 Secondary RPF: 00000000 RPF Fast Convergence timer: 0 ext_leaf: 0x8ce80080 Route OCE Entry Information ---------------------------------------------------------- Interface Handle IC Accept NS F/EG ---------------------------------------------------------- Se0/4/0/0/1 0xc000ec0 F T T F **** Leaf Info (in cp) : [9dcbd9bc] oce flags = 0x6 next obj type : 11 next obj handle : a73e9104 **** Leaf Info (in cpp): [0] leaf_flags= 0x1 oce_flags: 0 oce_ptr: 0x8c5800c0 ---------------------------------------------------------- Interface Handle IC Accept NS F/EG ---------------------------------------------------------- Gi0/4/3/0 0xc000080 F F T T **** Leaf Info (in cp) : [9dcbd450] oce flags = 0x5 next obj type : 11 next obj handle : a73e907c **** Leaf Info (in cpp): [0x8c5800f0] leaf_flags= 0x1 oce_flags: 0x2 oce_ptr: 0x8c580000 Route OLIST Information ---------------------------------------------------------- TREE .. : root : 9dcbd530 num_nodes 1 num_leaves 1 (in cp) Node: 9dcbd530 num_child:1 cum[wt:1 free:6] (in cpp) Node : 0x8d080080 flags : 0x4 child[0]: [Leaf] in cp : 9dcbd450 in cpp : 0x8c5800f0) child[1]: [NULL] child[2]: [NULL] child[3]: [NULL] child[4]: [NULL] child[5]: [NULL] child[6]: [NULL] Route Rx Adjacency Information ---------------------------------------------------------- OCE RX Adj Data for 0x8bb00160: base: 39(CPP HW RX ADJ IPV4 MCAST) adj_flags: 0x0 pd_16: 0x40 pd_32: 0x4275 output_uidb: 0x1fab counters_ptr: 0x893f5c50 byte count: 9800 packet count: 196 Hardware Route Information ---------------------------------------------------------- Source |Group |M |C|RPF |S|IC|PR|PK|FGID |MGID |PAL Olist Handle|CPP OLIST Handle|Num OCE| ---------------------------------------------------------- 12.12.12.2|225.0.0.0 |64 |F|Se0/4/0/0/1|F| F| F|F |64 |17024|0x9dcbcecc |0x9dc86a54 |2 | Ingress CPP Prefix Information ---------------------------------------------------------- === QFP Multicast prefix info === Root: 9dcbcfb0, Flags: 0 First leaf: 9dcbccfc Number of nodes: 0x000001, leaves: 0x000001 RPF i/f: 0x007fff RPF Fast Convergence flags: 00000000 Secondary RPF: 00000000 RPF Fast Convergence timer: 0 ext_leaf: 0x8b900200 Egress CPP Prefix Information ---------------------------------------------------------- === QFP Multicast prefix info === Root: 9dcbcfb0, Flags: 0 First leaf: 9dcbccfc Number of nodes: 0x000001, leaves: 0x000001 RPF i/f: 0x007fff RPF Fast Convergence flags: 00000000 Secondary RPF: 00000000 RPF Fast Convergence timer: 0 ext_leaf: 0x8ce80200 Route OCE Entry Information ---------------------------------------------------------- Interface Handle IC Accept NS F/EG ---------------------------------------------------------- Se0/4/0/0/1 0xc000ec0 F T F F **** Leaf Info (in cp) : [9dcbccfc] oce flags = 0x2 next obj type : 11 next obj handle : a73e9104 **** Leaf Info (in cpp): [0] leaf_flags= 0x1 oce_flags: 0 oce_ptr: 0x8c5800c0 ---------------------------------------------------------- Interface Handle IC Accept NS F/EG ---------------------------------------------------------- Gi0/4/3/0 0xc000080 F F T T **** Leaf Info (in cp) : [9dcbcddc] oce flags = 0x5 next obj type : 11 next obj handle : a73e907c **** Leaf Info (in cpp): [0x8c5800d0] leaf_flags= 0x1 oce_flags: 0x2 oce_ptr: 0x8c580000 Route OLIST Information ---------------------------------------------------------- TREE .. : root : 9dcbcfb0 num_nodes 1 num_leaves 1 (in cp) Node: 9dcbcfb0 num_child:1 cum[wt:1 free:6] (in cpp) Node : 0x8d080000 flags : 0x4 child[0]: [Leaf] in cp : 9dcbcddc in cpp : 0x8c5800d0) child[1]: [NULL] child[2]: [NULL] child[3]: [NULL] child[4]: [NULL] child[5]: [NULL] child[6]: [NULL] Route Rx Adjacency Information ---------------------------------------------------------- OCE RX Adj Data for 0x8bb00050: base: 39(CPP HW RX ADJ IPV4 MCAST) adj_flags: 0x0 pd_16: 0x40 pd_32: 0x4280 output_uidb: 0x1fab counters_ptr: 0x893f5c60 byte count: 348116500 packet count: 6962330 Hardware Route Information ---------------------------------------------------------- Source |Group |M |C|RPF |S|IC|PR|PK|FGID |MGID |PAL Olist Handle|CPP OLIST Handle|Num OCE| ---------------------------------------------------------- * |232.0.0.0 |8 |F|Null |F| F| F|F |0 |16963|0x9e07d184 |0x9dc868d8 |0 | Ingress CPP Prefix Information ---------------------------------------------------------- === QFP Multicast prefix info === Root: 9e07d110, Flags: 0 First leaf: 0 Number of nodes: 0x000001, leaves: 00000000 RPF i/f: 00000000 RPF Fast Convergence flags: 00000000 Secondary RPF: 00000000 RPF Fast Convergence timer: 0 ext_leaf: 0x8b900140 Egress CPP Prefix Information ---------------------------------------------------------- === QFP Multicast prefix info === Root: 9e07d110, Flags: 0 First leaf: 0 Number of nodes: 0x000001, leaves: 00000000 RPF i/f: 00000000 RPF Fast Convergence flags: 00000000 Secondary RPF: 00000000 RPF Fast Convergence timer: 0 ext_leaf: 0x8ce80140 Route OCE Entry Information Route OLIST Information ---------------------------------------------------------- TREE .. : root : 9e07d110 num_nodes 1 num_leaves 0 (in cp) Node: 9e07d110 num_child:0 cum[wt:0 free:7] (in cpp) Node : 0x8d0800e0 flags : 0x4 child[0]: [NULL] child[1]: [NULL] child[2]: [NULL] child[3]: [NULL] child[4]: [NULL] child[5]: [NULL] child[6]: [NULL] Route Rx Adjacency Information ---------------------------------------------------------- OCE RX Adj Data for 0x8bb00080: base: 39(CPP HW RX ADJ IPV4 MCAST) adj_flags: 0x0 pd_16: 0x0 pd_32: 0x4243 output_uidb: 0x1fab counters_ptr: 0x893f5c20 byte count: 0 packet count: 0
The following is sample output from the show mfib hardware route olist command with only one multicast group:
RP/0/RSP0/CPU0:router# show mfib hardware route olist 227.0.0.1 location 0/0/CPU0
--------------------------------------------------------------------------
Legend:
Route Information - (Ingress)
C: Chip ID, IC: BACL check, IP: Punt this packet to LC CPU,
ID: Directly connected, IS: RPF interface signal, IU: Punt copy to RP,
IF: Punt to LC CPU if forwarded, IM: Result match, IV: Valid entry,
IR: RPF IF, IA: Fabric slotmask, IG: Multicast group ID
Route Information - (Egress)
ET: Table ID to be used for OLIST lookup, EO: OLIST count bit,
ER: Route MGID to be used for OLIST/NRPF lookup, EM: Result match,
EV: Valid entry, EC: Count of OLIST members on this chip,
BS: Base of the statistics pointer
Hardware Information
C: Chip ID; T: Table ID; M: Member ID; Intf: Interface, U: uIDB index,
I: HW IC flag, B: HW BACL bit, Base: Base of statistics pointer
--------------------------------------------------------------------------
Source: * Group: 227.0.0.1 Mask length: 32
Route Information
----------------------------------------------------------------------------------
C IC IP ID IS IU IF IM IV IR IA IG ET EO ER EM EV EC BS
----------------------------------------------------------------------------------
0 T F F F F F T T 0x0 0x1 0x8004 0 F 5 T T 0 0x55185
1 T F F F F F T T 0x0 0x1 0x8004 0 F 5 T T 0 0x55185
2 T F F F F F T T 0x0 0x1 0x8004 0 F 5 T T 0 0x55185
3 T F F F F F T T 0x0 0x1 0x8004 1 T 5 T T 3 0x555bd
----------------------------------------------------------------------------------
Interface Information
-----------------------------------------------------
C T M Intf U I B Base
-----------------------------------------------------
3 1 0 Gi0/0/0/8 9 F F 0x5540c
3 1 1 Gi0/0/0/4 5 F F 0x5540f
3 1 2 Gi0/0/0/6 7 F F 0x55412
-----------------------------------------------------
Related Commands
Command | Description |
| Displays platform-specific Multicast Forwarding Information Base (MFIB) information for the interface list that accepts bidirectional routes. |
| Displays platform-specific Multicast Forwarding Information Base (MFIB) information for the packet and byte counters for each route. |
| Displays summary platform-specific Multicast Forwarding Information Base (MFIB) hardware information for each route entry. |
| Displays route entries in the Multicast Forwarding Information Base (MFIB). |
show mfib hardware route statistics
To display platform-specific Multicast Forwarding Information Base (MFIB) information for the packet and byte counters for each route, use the show mfib hardware route statistics command in EXEC mode.
show mfib [ vrf vrf-name ] [ ipv4 | ipv6 ] hardware route statistics [detail] [*] [source-address] [ group-address [ /prefix-length ] ] [ location node-id ]
Syntax Description
|
vrf vrf-name |
(Optional) Specifies a VPN routing and forwarding (VRF) instance. |
|
ipv4 |
(Optional) Specifies IPv4 address prefixes. |
|
ipv6 |
(Optional) Specifies IPv6 address prefixes. |
|
* |
(Optional) Displays shared tree entries. |
|
source-address |
(Optional) IP address or hostname of the multicast route source. |
|
group-address |
(Optional) IP address or hostname of the multicast group. |
|
/ prefix-length |
(Optional) Prefix length of the multicast group. A decimal value that indicates how many of the high-order contiguous bits of the address compose the prefix (the network portion of the address). A slash must precede the decimal value. |
|
detail |
(Optional) Displays a detailed list of the routing database. |
|
location node-id |
(Optional) Specifies an MFIB-designated node. |
Command Default
IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the show mfib hardware route statistics command to display the hardware packet and byte counter for a route. Route counters are kept for (S, G) routes only. A single set of counters is provided for all
(*, G) routes.
This command displays the hardware packet and bytes count on a per-route basis. Per-route hardware counters are kept for (S, G) routes only. However, counters are managed dynamically and allocated on a priority basis and may not be available for each (S, G) route. There is a single set of counters for all
(*, G) routes. For example, interface counters and access list counters have higher priority than route counters.
Note | Route counters are local to each line card. |
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read |
Examples
The following is sample output from the show mfib hardware route statistics command.
RP/0/RSP0/CPU0:router# show mfib hardware route statistics location 0/4/CPU0 LC Type: A9K-SIP-700 Hardware Prefix Statistics ----------------------------------------------------------------------------------------------- (s, g) RX/TX: Pkt/Byte: Forward(Pkt/Byte) Punt(Pkt/Byte) RPF Fail(Pkt/Byte) Drop(Pkt/Byte) ----------------------------------------------------------------------------------------------- (* , 224.0.0.0 ) RX: 0/0 0/0 0/0 0/0 (* , 224.0.0.0 ) TX: 0/0 0/0 0/0 0/0 (* , 224.0.0.0 ) RX: 0/0 0/0 0/0 0/0 (* , 224.0.0.0 ) TX: 0/0 0/0 0/0 0/0 (* , 224.0.1.39) RX: 0/0 0/0 0/0 0/0 (* , 224.0.1.39) TX: 0/0 0/0 0/0 0/0 (* , 224.0.1.40) RX: 0/0 0/0 0/0 0/0 (* , 224.0.1.40) TX: 0/0 0/0 0/0 0/0 (* , 225.0.0.0 ) RX: 196/9016 1/46 0/0 0/0 (* , 225.0.0.0 ) TX: 196/9016 0/0 0/0 0/0 (12.12.12.2, 225.0.0.0 ) RX: 7931284/364839064 3/138 0/0 0/0 (12.12.12.2, 225.0.0.0 ) TX: 7931288/364839248 0/0 0/0 0/0 (* , 232.0.0.0 ) RX: 0/0 0/0 0/0 0/0 (* , 232.0.0.0 ) TX: 0/0 0/0 0/0 0/0 RP/0/RSP0/CPU0:router# show mfib hardware route statistics location 0/0/CPU0 LC Type: Trident Legend: S: Source, G: Group, Pr: Prefix Length, C: Chip ID, R: Received, P: Punted to CPU, F: Forwarded, ID: Ingress Drop, ED: Egress Drop S: * G: 224.0.0.0 Pr:24 ----------------------------------------------------------------------- C R(packets:bytes)/F(packets:bytes)/P(packets)/ID(packets)/ED(packets) ----------------------------------------------------------------------- 0 0:0 / 0:0 / 0 / 0 / 0 1 0:0 / 0:0 / 0 / 0 / 0 2 0:0 / 0:0 / 0 / 0 / 0 3 0:0 / 0:0 / 0 / 0 / 0 ----------------------------------------------------------------------- No OLIST interfaces found for this route S: * G: 224.0.1.39 Pr:32 ----------------------------------------------------------------------- C R(packets:bytes)/F(packets:bytes)/P(packets)/ID(packets)/ED(packets) ----------------------------------------------------------------------- 0 0:0 / 0:0 / 0 / 0 / 0 1 0:0 / 0:0 / 0 / 0 / 0 2 0:0 / 0:0 / 0 / 0 / 0 3 0:0 / 0:0 / 0 / 0 / 0 ----------------------------------------------------------------------- No OLIST interfaces found for this route S: * G: 224.0.1.40 Pr:32 ----------------------------------------------------------------------- C R(packets:bytes)/F(packets:bytes)/P(packets)/ID(packets)/ED(packets) ----------------------------------------------------------------------- 0 0:0 / 0:0 / 0 / 0 / 0 1 0:0 / 0:0 / 0 / 0 / 0 2 0:0 / 0:0 / 0 / 0 / 0 3 0:0 / 0:0 / 0 / 0 / 0 ----------------------------------------------------------------------- No OLIST interfaces found for this route S: * G: 227.0.0.1 Pr:32 ----------------------------------------------------------------------- C R(packets:bytes)/F(packets:bytes)/P(packets)/ID(packets)/ED(packets) ----------------------------------------------------------------------- 0 0:0 / 0:0 / 0 / 0 / 0 1 0:0 / 0:0 / 0 / 0 / 0 2 0:0 / 0:0 / 0 / 0 / 0 3 504844:30290640 / 504843:23222778 / 504856 / 0 / 0 ----------------------------------------------------------------------- Interface Statistics: ----------------------------------------------------------------------- Interface F/P/D (packets:bytes) ----------------------------------------------------------------------- Gi0/0/0/8 504843:23222778 / 0:0 / 0:0 Gi0/0/0/4 0:0 / 0:0 / 0:0 Gi0/0/0/6 504843:23222778 / 0:0 / 0:0 ----------------------------------------------------------------------- S: 4.0.0.2 G: 227.0.0.1 Pr:64 ----------------------------------------------------------------------- C R(packets:bytes)/F(packets:bytes)/P(packets)/ID(packets)/ED(packets) ----------------------------------------------------------------------- 0 0:0 / 0:0 / 0 / 0 / 0 1 0:0 / 0:0 / 0 / 0 / 0 2 0:0 / 0:0 / 0 / 0 / 0 3 3869:232140 / 3869:177974 / 0 / 0 / 0 ----------------------------------------------------------------------- Interface Statistics: ----------------------------------------------------------------------- Interface F/P/D (packets:bytes) ----------------------------------------------------------------------- Gi0/0/0/4 0:0 / 0:0 / 0:0 Gi0/0/0/8 3869:177974 / 0:0 / 0:0 Gi0/0/0/6 3869:177974 / 0:0 / 0:0 ----------------------------------------------------------------------- S: * G: 230.0.0.0 Pr:8 ----------------------------------------------------------------------- C R(packets:bytes)/F(packets:bytes)/P(packets)/ID(packets)/ED(packets) ----------------------------------------------------------------------- 0 0:0 / 0:0 / 0 / 0 / 0 1 0:0 / 0:0 / 0 / 0 / 0 2 0:0 / 0:0 / 0 / 0 / 0 3 0:0 / 0:0 / 0 / 0 / 0 ----------------------------------------------------------------------- No OLIST interfaces found for this route S: * G: 232.0.0.0 Pr:8 ----------------------------------------------------------------------- C R(packets:bytes)/F(packets:bytes)/P(packets)/ID(packets)/ED(packets) ----------------------------------------------------------------------- 0 0:0 / 0:0 / 0 / 0 / 0 1 0:0 / 0:0 / 0 / 0 / 0 2 0:0 / 0:0 / 0 / 0 / 0 3 0:0 / 0:0 / 0 / 0 / 0 ----------------------------------------------------------------------- No OLIST interfaces found for this route
|
Field |
Description |
|---|---|
|
Ingress Counter |
Unique identifier of the ingress counter. |
|
Egress Counter |
Unique identifier of the egress counter. |
|
Forward |
Number of forwarded packets and bytes. |
|
Punt |
Number of bytes punted from the line card CPU. |
|
Drop |
Number of dropped bytes. |
Related Commands
Command | Description |
| Displays platform-specific Multicast Forwarding Information Base (MFIB) information for the interface list that accepts bidirectional routes. |
| Displays platform-specific Multicast Forwarding Information Base (MFIB) information in the output interface list (olist) stored in the hardware. |
| Displays summary platform-specific Multicast Forwarding Information Base (MFIB) hardware information for each route entry. |
| Displays route entries in the Multicast Forwarding Information Base (MFIB). |
show mfib hardware route summary
To display summary platform-specific Multicast Forwarding Information Base (MFIB) hardware information for each route entry, use the show mfib hardware route summary command in EXEC mode.
show mfib [ vrf vrf-name ] [ ipv4 | ipv6 ] hardware route summary location node-id
Syntax Description
|
vrf vrf-name |
(Optional) Specifies a VPN routing and forwarding (VRF) instance. |
|
ipv4 |
(Optional) Specifies IPv4 address prefixes. |
|
ipv6 |
(Optional) Specifies IPv6 address prefixes. |
|
location node-id |
(Optional) Specifies an MFIB-designated node. |
Command Default
IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Use the show mfib hardware summary command to display hardware information for the route of the node.
The hardware information of MoFRR (multicast only fast reroute) enabled routes are also displayed. In IOS XR Software Release 3.9.0, the maximum platform supported MoFRR routes are 1024.
The longest-prefix match route is displayed depending on the provided source and group addresses. The command does not display any useful output if only RSP is specified or if no location is specified.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read |
Examples
The following is sample output from the show mfib hardware route summary command:
RP/0/RSP0/CPU0:router# show mfib hardware route summary location 0/1/cpu0
LC Type: Trident
H/W IP Multicast Forwarding Information Base Summary
No. of (*,G) routes = 5
No. of (S,G) routes = 10
RP/0/RSP0/CPU0:router# show mfib hardware route summary location 0/0/CPU0
LC Type: Trident
H/W IP Multicast Forwarding Information Base Summary
No. of (*,G) routes = 6
No. of (S,G) routes = 5
No. of (S,G) MoFRR routes = 0, Maximum supported MoFRR routes = 1024
RP/0/RSP0/CPU0:router# show mfib hardware route summary location 0/4/cPU0
LC Type: A9K-SIP-700
Hardware IP Multicast Forwarding Information Base Route Summary
Number of hardware (*, G) routes = 6
Number of hardware (S, G) routes = 1
Number of hardware route-interfaces = 4
Number of hardware Rx adjacencies = 7
Number of hardware Tx adjacencies = 3
Number of ref to decap adjacency = 0
Mvpn master LC status = False
If there is no MoFRR configured in the platform:
RP/0/RSP0/CPU0:router# show mfib hardware route summary location 0/0/CPU0
LC Type: Trident
H/W IP Multicast Forwarding Information Base Summary
No. of (*,G) routes = 6
No. of (S,G) routes = 5
No. of (S,G) MoFRR routes = 0, Maximum supported MoFRR routes = 1024
|
Field |
Description |
|---|---|
|
No. of (*,G) routes |
Number of (*,G) routes installed in hardware. |
|
No. of (S,G) routes |
Number of (S,G) routes installed in hardware. |
|
No. of (S,G) MoFRR routes |
Number of MoFRR (S,G) routes installed in hardware. |
|
Maximum supported MoFRR routes |
Maximum number of MoFRR routes supported in hardware. |
Related Commands
Command | Description |
| Displays platform-specific Multicast Forwarding Information Base (MFIB) information for the interface list that accepts bidirectional routes. |
| Displays the platform-specific Multicast Forwarding Information Base (MFIB) information for the MoFRR (multicast only fast reroute)- enabled list stored in the hardware. |
| Displays platform-specific Multicast Forwarding Information Base (MFIB) information in the output interface list (olist) stored in the hardware. |
| Displays platform-specific Multicast Forwarding Information Base (MFIB) information for the packet and byte counters for each route. |
| Displays route entries in the Multicast Forwarding Information Base (MFIB). |
show mfib hardware table
To display the platform-specific multicast table information for the Multicast Forwarding Information Base (MFIB) in the hardware, use the show mfib hardware table command in EXEC mode.
show mfib [ vrf vrf-name ] [ ipv4 | ipv6 ] hardware table [detail] [ location node-id ]
Syntax Description
|
vrf vrf-name |
(Optional) Specifies a VPN routing and forwarding (VRF) instance. |
|
ipv4 |
(Optional) Specifies IPv4 address prefixes. |
|
ipv6 |
(Optional) Specifies IPv6 address prefixes. |
|
detail |
(Optional) Displays detailed platform-specific multicast table information. |
|
location node-id |
(Optional) Specifies the MFIB location. |
Command Default
IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
|
Release 3.9.1 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Note | The command does not display any useful output if only RSP is specified or if no location is specified. |
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read |
Examples
The following example shows a sample output of the show mfib hardware table command:
RP/0/RSP0/CPU0:router# show mfib hardware table detail location 0/1/CPU0
LC Type: Trident
-------------------------------------------------------------------
Legend:
NP: Network Processor, MNP: Master NP, SW OC: Software OLIST Count
TID: Table ID, MLC: Master Linecard (PD Flag)
MNP_id: Master NP ID, C_NP_MASK: Composite NP Mask
-------------------------------------------------------------------
---------------
NP MNP SW OC
---------------
0 F 0
1 F 0
2 F 0
3 F 0
---------------
---------------------------
TID MLC MNP_id C_NP_MASK
---------------------------
0x0 F 0 0x0
---------------------------
|
Field |
Description |
|---|---|
|
NP |
Specifies the network processor. |
|
MNP |
Specifies the master network processor. |
|
SW OC |
Specifies the software OLIST count. |
|
TID |
Specifies the Table ID. |
show mfib interface
To display interface-related information used during software multicast switching in the Multicast Forwarding Information Base (MFIB) process, use the show mfib interface command in EXEC mode.
show mfib [ vrf vrf-name ] ipv4 interface [ type interface-path-id ] [ detail | route ] [ location node-id ]
Syntax Description
|
vrf vrf-name |
(Optional) Specifies a VPN routing and forwarding (VRF) instance. |
||
|
ipv4 |
(Optional) Specifies IPv4 address prefixes. |
||
|
type |
(Optional) Interface type. For more information, use the question mark (?) online help function. |
||
|
interface-path-id |
(Optional) Physical interface or virtual interface.
For more information about the syntax for the router, use the question mark ( ? ) online help function. |
||
|
detail |
(Optional) Specifies detailed information for packet statistics on interfaces. |
||
|
route |
(Optional) Specifies a list of routes associated with the interface. This option is available if an interface type and instance are specified. |
||
|
location node-id |
(Optional) Specifies packet statistics associated with an interface of the designated node. |
Command Default
IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The show mfib interface command displays counters for the number of packets and bytes that are handled by software switching. Counters for packets processed by hardware are displayed by the appropriate show mfib hardware command.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read |
Examples
The following is sample output from the show mfib interface command for the multicast route on node 0/2/CPU0 that is associated with the Gigabit Ethernet interface 0/2/0/2:
RP/0/RSP0/CPU0:router# show mfib interface GigE 0/2/0/2 location 0/2/CPU0
Interface : GigE0/2/0/2 (Enabled)
Mcast pkts in : 5839, Mcast pkts out : 0 TTL Threshold : 0 Ref Count : 18
The following is sample output from the show mfib interface command with the detail and location keywords specified:
RP/0/RSP0/CPU0:router# show mfib interface detail location 0/2/CPU0
Interface : FINT0/2/CPU0 [0x3000000] (Disabled) PHYSICAL Create Unknown Mcast pkts in: 0, Mcast pkts out: 0 TTL Threshold : 0, VRF ID: 0x60000000, Multicast Adjacency Ref Count: 2, Route Count: 0, Handle: 0x3000000 Primary address : 0.0.0.0/32 Secondary address : 0.0.0.0/32
Interface : GigE0/2/0/2 [0x3000900] (Enabled) PHYSICAL Create Rcvd Mcast pkts in: 5844, Mcast pkts out: 0 TTL Threshold : 0, VRF ID: 0x60000000, Multicast Adjacency Ref Count: 18, Route Count: 15, Handle: 0x3000900 Primary address : 112.112.112.203/24 Secondary address : 0.0.0.0/32
|
Field |
Description |
|---|---|
|
Interface |
Interface name. Enabled if the interface is configured for multicast routing. The word “PHYSICAL” is displayed if the interface is a nonvirtual interface. |
|
Mcast pkts in |
Number of incoming multicast packets entering the interface during software switching. |
|
Mcast pkts out |
Number of outgoing multicast packets exiting the interface during software switching. |
|
TTL Threshold |
Number of multicast packets that reach the configured multicast time-to-live threshold. |
|
VRF ID |
VPN Routing and Forwarding instance ID. |
|
Ref Count |
Number of references to this interface structure in the MFIB process. |
|
Primary address |
Primary IP address of the interface. |
|
Secondary address |
Secondary IP address of the interface. |
Related Commands
Command | Description |
| Displays hardware switching interface information for the Multicast Forwarding Information Base (MFIB) process. |
show mfib nsf
To display the state of a nonstop forwarding (NSF) operation for the Multicast Forwarding Information Base (MFIB) line cards, use the show mfib nsf command in EXEC mode.
show mfib [ ipv4 ] nsf [ location node-id ]
Syntax Description
|
ipv4 |
(Optional) Specifies IPv4 address prefixes. |
|
location node-id |
(Optional) Specifies the MFIB NSF designated node. |
Command Default
IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The show mfib nsf command displays the current multicast NSF state for the MFIB process contained on all line cards and route processors (RPs) in the router.
For multicast NSF, the state may be one of the following:
- Normal—Normal operation: The MFIBs in the card contain only up-to-date MFIB entries.
- Boot Card Booting—Card is initializing and has not yet determined its NSF state.
- Not Forwarding—Multicast Forwarding Disabled: Multicast routing failed to recover from a failure-induced NSF state prior to the MFIB NSF timeout.
- Non-stop Forwarding Activated—Multicast NSF active: The router is operating in NSF mode while attempting to recover from a control-plane failure. In this mode, data is forwarded based on MFIB entries that are either updated by the recovered Multicast Routing Information Base (MRIB), or MFIB entries that were marked stale when NSF mode began. The times remaining until multicast NSF and multicast-unicast NSF expiration are displayed.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read |
Examples
The following is sample output from the show mfib nsf command:
RP/0/RSP0/CPU0:router# show mfib nsf
IP MFWD Non-Stop Forwarding Status:
NSF Lifetime: 00:15:00
On node 0/1/CPU0 :
Multicast routing state: Non-Stop Forwarding is activated
NSF Time Remaining: 00:14:54
On node 0/3/CPU0 :
Multicast routing state: Non-Stop Forwarding is activated
NSF Time Remaining: 00:14:54
On node 0/4/CPU0 :
Multicast routing state: Non-Stop Forwarding is activated
NSF Time Remaining: 00:14:53
On node 0/6/CPU0 :
Multicast routing state: Non-Stop Forwarding is activated
NSF Time Remaining: 00:14:53
|
Field |
Description |
|---|---|
|
IP MFWD Non-Stop Forwarding Status |
MFIB NSF status of each node in the system: booting, normal, not forwarding, or activated. |
|
NSF Time Remaining |
If MSB NSF is activated, the time remaining until NSF fails and all routes are deleted displays. Before timeout, MRIB signals that NSF (in the control plane) is finished and new, updated routes are populated in the MFIB (which makes the transition to Normal status). |
Related Commands
|
Command |
Description |
|---|---|
|
nsf lifetime (IGMP) |
Configures the maximum time for the NSF timeout value under IGMP. |
|
Configures the NSF capability for the multicast routing system. |
|
|
nsf lifetime (PIM) |
Configures the NSF timeout value for the PIM process. |
|
show igmp nsf |
Displays the state of NSF operation in IGMP. |
|
Displays the state of NSF operation in the MRIB. |
|
|
show pim nsf |
Displays the state of NSF operation for PIM. |
show mfib route
To display route entries in the Multicast Forwarding Information Base (MFIB), use the show mfib route command in EXEC mode.
show mfib [ vrf vrf-name ] ipv4 route [ rate | * | source-IP-address | group-IP-address /prefix-length | detail | summary | location node-id ]
Syntax Description
|
* |
(Optional) Display shared tree entries. |
|
source-IP-address |
(Optional) IP address or hostname of the multicast route source. Format is: A.B.C.D |
|
group-IP-address |
(Optional) IP address or hostname of the multicast group. Format is: A.B.C.D |
|
/prefix-length |
(Optional) Group IP prefix length of the multicast group. A decimal value that indicates how many of the high-order contiguous bits of the address compose the prefix (the network portion of the address). Format is: A.B.C.D/length |
|
vrf vrf-name |
(Optional) Specifies a VPN routing and forwarding (VRF) instance. |
|
ipv4 |
(Optional) Specifies IPv4 address prefixes. |
|
ipv6 |
(Optional) Specifies IPv6 address prefixes. |
|
detail |
(Optional) Specifies detailed route information. |
|
location node-id |
(Optional) Specifies an MFIB-designated node. |
|
rate |
(Optional) Displays individual (S, G) rates. |
|
sources-only |
(Optional) Restricts display of any shared-tree entries. |
|
summary |
(Optional) Displays a brief list of the routing database. |
|
tech-support |
(Optional) Displays technical support information. |
Command Default
IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
All entries in the MFIB table are derived from the Multicast Routing Information Base (MRIB). The flags have the same connotation as in the MRIB. The flags determine the forwarding and signaling behavior according to a set of forwarding rules for multicast packets. In addition to the list of interfaces and flags, each route entry shows various counters. Byte count is the number of total bytes forwarded. Packet count is the number of packets received for this entry.
The show mfib counter command displays global counters independent of the routes.
This command displays counters for the number of packets and bytes that are handled by software switching. Counters for packets processed by hardware are displayed by the appropriate show mfib hardware command.
The command displays the cumulative rates per route for all line cards in the Multicast Forwarding Information Base (MFIB) table when the rate keyword is used with the source and group IP addresses.
The show mfib route rate command is not supported on interfaces such as bundle virtual interfaces and Bridge Group virtual interfaces (BVIs).
The command displays the rate per route for one line card in Multicast Forwarding Information Base (MFIB) table when the statistics keyword is used.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read |
Examples
The following is sample output from the show mfib route command with the location keyword specified (the output fields are described in the header):
RP/0/RSP0/CPU0:router# show mfib route location 0/1/CPU0
IP Multicast Forwarding Information Base
Entry flags: C - Directly-Connected Check, S - Signal, D - Drop,
IA - Inherit Accept, IF - Inherit From, MA - MDT Address,
ME - MDT Encap, MD - MDT Decap, MT - MDT Threshold Crossed,
MH - MDT interface handle, CD - Conditional Decap,
DT - MDT Decap True
Interface flags: F - Forward, A - Accept, IC - Internal Copy,
NS - Negate Signal, DP - Don't Preserve, SP - Signal Present,
EG - Egress, EI - Encapsulation Interface, MI - MDT Interface
Forwarding Counts: Packets in/Packets out/Bytes out
Failure Counts: RPF / TTL / Empty Olist / Encap RL / Other
(*,224.0.0.0/24), Flags: D
Up: 02:16:52
Last Used: never
SW Forwarding Counts: 0/0/0
SW Failure Counts: 0/0/0/0/0
(*,224.0.1.39), Flags: S
Up: 02:16:52
Last Used: never
SW Forwarding Counts: 0/0/0
SW Failure Counts: 0/0/0/0/0
(*,224.0.1.40), Flags: S
Up: 02:16:52
Last Used: never
SW Forwarding Counts: 0/0/0
SW Failure Counts: 0/0/0/0/0
(*,227.0.0.1), Flags: C
Up: 02:16:51
Last Used: 02:16:50
SW Forwarding Counts: 282/0/0
SW Failure Counts: 205/0/0/0/0
GigabitEthernet0/0/0/4 Flags: NS EG, Up:02:16:46
GigabitEthernet0/0/0/8 Flags: NS EG, Up:02:16:50
GigabitEthernet0/0/0/6 Flags: NS EG, Up:02:16:50
(4.0.0.2,227.0.0.1), Flags:
Up: 02:16:50
Last Used: 00:00:12
SW Forwarding Counts: 125/0/0
SW Failure Counts: 0/0/0/0/0
GigabitEthernet0/0/0/8 Flags: NS EG, Up:02:16:50
GigabitEthernet0/0/0/6 Flags: NS EG, Up:02:16:50
GigabitEthernet0/0/0/4 Flags: A EG, Up:02:16:50
(*,232.0.0.0/8), Flags: D
Up: 02:16:52
Last Used: never
SW Forwarding Counts: 0/0/0
SW Failure Counts: 0/0/0/0/0
The following is sample output from the show mfib route command with the summary and location keywords specified:
RP/0/RSP0/CPU0:router# show mfib route summary location 0/0/CPU0
IP Multicast Forwarding Information Base Summary for VRF default
No. of (*,G) routes = 5
No. of (S,G) routes = 1
The following is sample output from the show mfib route command with the statistics and location keywords specified. If the hardware counters show N/A, it means no hardware statistic blocks were assigned to the route. However, routes may show that both hardware and software statistic blocks are assigned. The output fields are described in the header.
RP/0/RSP0/CPU0:router# show mfib route statistics location 0/0/CPU0
IP Multicast Forwarding Information Base
Entry flags: C - Directly-Connected Check, S - Signal, D - Drop,
IA - Inherit Accept, IF - Inherit From, MA - MDT Address,
ME - MDT Encap, MD - MDT Decap, MT - MDT Threshold Crossed,
MH - MDT interface handle, CD - Conditional Decap,
DT - MDT Decap True
Interface flags: F - Forward, A - Accept, IC - Internal Copy,
NS - Negate Signal, DP - Don't Preserve, SP - Signal Present,
EG - Egress, EI - Encapsulation Interface, MI - MDT Interface
SW/HW Forwarding Counts: Packets in/Packets out/Bytes out
SW Failure Counts: RPF / TTL / Empty Olist / Encap RL / Other
HW Drop Counts: Ingress / Egress
HW Forwarding Rates: bps In/pps In/bps Out/pps Out
(*,224.0.0.0/24), Flags: D
Up: 02:21:15
Last Used: never
SW Forwarding Counts: 0/0/0
SW Failure Counts: 0/0/0/0
HW Forwarding Counts: 0/0/0
HW Drop Counts: 0/0
HW Forwarding Rates: N/A /N/A /N/A /N/A
(*,224.0.1.39), Flags: S
Up: 02:21:15
Last Used: never
SW Forwarding Counts: 0/0/0
SW Failure Counts: 0/0/0/0
HW Forwarding Counts: 0/0/0
HW Drop Counts: 0/0
HW Forwarding Rates: N/A /N/A /N/A /N/A
(*,224.0.1.40), Flags: S
Up: 02:21:15
Last Used: never
SW Forwarding Counts: 0/0/0
SW Failure Counts: 0/0/0/0
HW Forwarding Counts: 0/0/0
HW Drop Counts: 0/0
HW Forwarding Rates: N/A /N/A /N/A /N/A
(*,227.0.0.1), Flags: C
Up: 02:21:14
Last Used: 02:21:14
SW Forwarding Counts: 282/0/0
SW Failure Counts: 205/0/0/0
HW Forwarding Counts: 0/0/0
HW Drop Counts: 0/0
HW Forwarding Rates: N/A /N/A /N/A /N/A
GigabitEthernet0/0/0/4 Flags: NS EG, Up:02:21:10
GigabitEthernet0/0/0/8 Flags: NS EG, Up:02:21:14
GigabitEthernet0/0/0/6 Flags: NS EG, Up:02:21:14
(4.0.0.2,227.0.0.1), Flags:
Up: 02:21:14
Last Used: 00:01:06
SW Forwarding Counts: 128/0/0
SW Failure Counts: 0/0/0/0
HW Forwarding Counts: 8474282/8474283/389817018
HW Drop Counts: 0/0
HW Forwarding Rates: N/A /N/A /N/A /N/A
GigabitEthernet0/0/0/8 Flags: NS EG, Up:02:21:14
GigabitEthernet0/0/0/6 Flags: NS EG, Up:02:21:14
GigabitEthernet0/0/0/4 Flags: A EG, Up:02:21:14
(*,232.0.0.0/8), Flags: D
Up: 02:21:15
Last Used: never
SW Forwarding Counts: 0/0/0
SW Failure Counts: 0/0/0/0
HW Forwarding Counts: 0/0/0
HW Drop Counts: 0/0
HW Forwarding Rates: N/A /N/A /N/A /N/A
The following is a sample output for MoFRR enabled route without and with the detail keyword:
RP/0/RSP0/CPU0:router# show mfib route
IP Multicast Forwarding Information Base
Entry flags: C - Directly-Connected Check, S - Signal, D - Drop,
IA - Inherit Accept, IF - Inherit From, MA - MDT Address,
ME - MDT Encap, MD - MDT Decap, MT - MDT Threshold Crossed,
MH - MDT interface handle, CD - Conditional Decap,
DT - MDT Decap True, EX - Extranet
MoFE - MoFRR Enabled, MoFS - MoFRR State
Interface flags: F - Forward, A - Accept, IC - Internal Copy,
NS - Negate Signal, DP - Don't Preserve, SP - Signal Present,
EG - Egress, EI - Encapsulation Interface, MI - MDT Interface,
EX - Extranet, A2 - Secondary Accept
Forwarding/Replication Counts: Packets in/Packets out/Bytes out
Failure Counts: RPF / TTL / Empty Olist / Encap RL / Other
(20.20.20.1,225.0.0.1), Flags: MoFE MoFS
Up: 03:22:30
Last Used: never
SW Forwarding Counts: 0/0/0
SW Replication Counts: 0/0/0
SW Failure Counts: 0/0/0/0/0
GigabitEthernet0/0/0/8 Flags: A, Up:03:22:30
GigabitEthernet0/0/0/18 Flags: A2, Up:03:22:30
GigabitEthernet0/0/0/28 Flags: NS, Up:03:22:30
(20.20.20.1,225.0.0.2), Flags: MoFE MoFS
Up: 03:22:30
Last Used: never
SW Forwarding Counts: 0/0/0
SW Replication Counts: 0/0/0
SW Failure Counts: 0/0/0/0/0
GigabitEthernet0/0/0/8 Flags: A, Up:03:22:30
GigabitEthernet0/0/0/18 Flags: A2, Up:03:22:30
GigabitEthernet0/0/0/28 Flags: NS, Up:03:22:30
In the above command, A flag represents the primary RPF of the MoFRR route, and A2 flag represents the backup RPF of the MoFRR route.
RP/0/RSP0/CPU0:router# show mfib route detail
IP Multicast Forwarding Information Base
Entry flags: C - Directly-Connected Check, S - Signal, D - Drop,
IA - Inherit Accept, IF - Inherit From, MA - MDT Address,
ME - MDT Encap, MD - MDT Decap, MT - MDT Threshold Crossed,
MH - MDT interface handle, CD - Conditional Decap,
DT - MDT Decap True, EX - Extranet
MoFE - MoFRR Enabled, MoFS - MoFRR State
Interface flags: F - Forward, A - Accept, IC - Internal Copy,
NS - Negate Signal, DP - Don't Preserve, SP - Signal Present,
EG - Egress, EI - Encapsulation Interface, MI - MDT Interface,
EX - Extranet, A2 - Secondary Accept
Forwarding/Replication Counts: Packets in/Packets out/Bytes out
Failure Counts: RPF / TTL / Empty Olist / Encap RL / Other
(20.20.20.1,225.0.0.1), Flags: MoFE MoFS
Up: 03:25:31
Last Used: never
SW Forwarding Counts: 0/0/0
SW Replication Counts: 0/0/0
SW Failure Counts: 0/0/0/0/0
Route ver: 0x4a13
MVPN Info :-
MDT Handle: 0x0, MDT Probe:N [N], Rate:N, Acc:N
MDT SW Ingress Encap V4/V6, Egress decap: 0 / 0, 0
MOFRR State: Inactive Sequence No 1
GigabitEthernet0/0/0/8 Flags: A, Up:03:25:31
GigabitEthernet0/0/0/18 Flags: A2, Up:03:25:31
GigabitEthernet0/0/0/28 Flags: NS, Up:03:25:31
(20.20.20.1,225.0.0.2), Flags: MoFE MoFS
Up: 03:25:31
Last Used: never
SW Forwarding Counts: 0/0/0
SW Replication Counts: 0/0/0
SW Failure Counts: 0/0/0/0/0
Route ver: 0x443e
MVPN Info :-
MDT Handle: 0x0, MDT Probe:N [N], Rate:N, Acc:N
MDT SW Ingress Encap V4/V6, Egress decap: 0 / 0, 0
MOFRR State: Inactive Sequence No 1
GigabitEthernet0/0/0/8 Flags: A, Up:03:25:31
GigabitEthernet0/0/0/18 Flags: A2, Up:03:25:31
GigabitEthernet0/0/0/28 Flags: NS, Up:03:25:31
The detail option illustrates the MoFRR state of each MoFRR route. At any moment, only one RPF forwards the traffic to the egress. The inactive state means the primary RPF forwards the traffic to the egress. The active state means that the backup RPF forwards the traffic to the egress. The sequence number reflects the number of switchovers of the MoFRR route.
Related Commands
Command | Description |
| Displays Multicast Forwarding Information Base (MFIB) counter statistics for packets that have dropped. |
| Displays platform-specific Multicast Forwarding Information Base (MFIB) information for the interface list that accepts bidirectional routes. |
| Displays platform-specific Multicast Forwarding Information Base (MFIB) information in the output interface list (olist) stored in the hardware. |
| Displays platform-specific Multicast Forwarding Information Base (MFIB) information for the packet and byte counters for each route. |
| Displays interface-related information used during software multicast switching in the Multicast Forwarding Information Base (MFIB) process. |
| Displays all entries in the Multicast Routing Information Base (MRIB). |
show mfib table-info
To display Multicast Forwarding Information Base (MFIB) table information, use the show mfib table-info command in EXEC mode.
show mfib [ ipv4 | ipv6 ] table-info { table-id | vrf-name } [ local | remote ] [ location node-id ]
Syntax Description
|
ipv4 |
(Optional) Specifies IPv4 address prefixes. |
|
ipv6 |
(Optional) Specifies IPv6 address prefixes. |
|
table-id |
Specifies the table identifier. Range is 0 to 4294967295. |
|
vrf-name |
Specifies the VRF name. |
|
local |
Specifies local tables only. |
|
remote |
Specifies remote tables only. |
|
location node-id |
(Optional) Specifies MFIB connections associated with an interface of the designated node. |
Command Default
IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read |
Examples
The following is sample output from the show mfib table-info command:
RP/0/RSP0/CPU0:router# show mfib table-info table-id location 0/0/CPU0
Table Name : default
VRid/TID/VID : 0x0 / 0xe0000000 / 0x60000000
Table type : TBL_TYPE_TID
Active/Linked : Y / Y
Prev Table ID : 0x0
Location : Local
Local ifcount : 16
Default MDT Encap : (*, */32)
MDT Master LC : N
Loopback (Encap Src) : 0x0 (Ha0x0)
Local EG intf cnt : 6
Data MDT : Acl - (-), All vrf routes N, 0 Kbps
RP/0/RSP0/CPU0:router#show mfib table-info vrf 101
Table Name : vrf15
VRid/TID/VID : 0x0 / 0xe000000f / 0x6000000f
Table type : TBL_TYPE_NAME_VID
Active/Linked : Y / Y
Prev Table ID : 0x0
Location : Local
Local ifcount : 2
Child routes : (5.5.5.5, 225.101.1.15/32)
Default MDT Handle : 0x0 (Ha0x0)
MDT Master LC : Y
Loopback (Encap Src) : 0x9000180 (Loopback0)
Local EG intf cnt : 508
Data MDT : Acl - (-), All vrf routes N, 0 Kbps
|
Field |
Description |
|---|---|
|
Table Name |
Name of the MFIB table. |
|
VRid/TID/VID |
Table identifiers. |
|
Table type |
Type of MFIB table. |
|
Active/Linked |
Table is active and linked. |
|
Location |
Location of the MFIB table. |
|
Local ifcount |
Local interface count. |
|
Child routes |
Child routes shows the number of extranet routes in receiver VRFs that reference this source VRF. |
|
Default MDT Encap |
Default MDT encapsulation. |
|
Default MDT Handle |
Default MDT interface handle for this VRF. |
|
MDT Master LC |
Field contains "Y" if this line card is a master line card for this VRF. |
|
Loopback (Encap Src) |
Loopback (encapsulation source). |
|
Local EG intf cnt |
Shows the number of local egress interfaces for this VRF and location. |
|
Data MDT |
Routes for which multicast data for a multicast distribution tree (MDT) was triggered. |
show mrib client
To display the state of the Multicast Routing Information Base (MRIB) client connections, use the show mrib client command in the appropriate mode.
show mrib [ vrf vrf-name ] ipv4 client [filter] [client-name]
Syntax Description
|
vrf vrf-name |
(Optional) Specifies a VPN routing and forwarding (VRF) instance. |
|
ipv4 |
(Optional) Specifies IPv4 address prefixes. |
|
ipv6 |
(Optional) Specifies IPv6 address prefixes. |
|
filter |
(Optional) Displays route and interface level flag changes that various MRIB clients have registered and shows what flags are owned by the MRIB clients. |
|
client-name |
(Optional) Name of a multicast routing protocol that acts as a client of MRIB, such as Protocol Independent Multicast (PIM) or Internet Group Management Protocol (IGMP). |
Command Default
IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read |
Examples
The following is sample output from the show mrib client command using the filter option:
RP/0/RSP0/CPU0:router# show mrib client filter
IP MRIB client-connections
igmp:417957 (connection id 0)
ownership filter:
interface attributes: II ID LI LD
groups:
include 0.0.0.0/0
interfaces:
include All
pim:417959 (connection id 1)
interest filter:
entry attributes: E
interface attributes: SP II ID LI LD
groups:
include 0.0.0.0/0
interfaces:
include All
ownership filter:
entry attributes: L S C IA IF D
interface attributes: F A IC NS DP DI EI
groups:
include 0.0.0.0/0
interfaces:
include All
bcdl_agent:1 (connection id 2)
interest filter:
entry attributes: S C IA IF D
interface attributes: F A IC NS DP SP EI
groups:
include 0.0.0.0/0
interfaces:
include All
ownership filter:
groups:
include 0.0.0.0/0
interfaces:
include All
|
Field |
Description |
|---|---|
|
igmp |
Name of the client. |
|
417957 |
Personal identifier (PID) or a unique ID assigned by MRIB. |
|
(connection id 0) |
Unique client connection identifier. |
|
ownership filter: |
Specifies all the route entry and interface-level flags that are owned by the client. As the owner of the flag, only the client can add or remove the flag. For example, only the Internet Group Management Protocol (IGMP) client can add the II flag on an interface. MRIB does not allow a non-owner to register or modify the same flag. |
|
groups: include 0.0.0.0/0interfaces: include All |
Groups and interfaces registered by the clients consisting of two lists. One is an include list (items for which the client requests to be notified.) The use of “All” implies all interfaces and 0.0.0.0/0 to indicate all groups. Not shown in this example is the exclude list. This list contains items for which the client requests not to be notified when modifications occur. |
|
interface attributes: II ID LI LD |
Interface-level flags set on the interface belong to a route. |
|
interest filter: |
Specifies all the flags, groups, and interfaces from which the client requests information. When a flag of interest for a client is modified, the client is notified. |
|
entry attributes: S C IA IF D |
Entry-level flags that are set on the route. |
Related Commands
Command | Description |
| Displays the state of a nonstop forwarding (NSF) operation for the Multicast Forwarding Information Base (MFIB) line cards. |
| Displays route entries in the Multicast Forwarding Information Base (MFIB). |
| Displays the state of nonstop forwarding (NSF) operation in the Multicast Routing Information Base (MRIB). |
show mrib bvi
To display the Bridge Virtual Interface (BVI) details in the Multicast Routing Information Base (MRIB), use the show mrib bvi command EXEC mode.
show mrib bvi[ interface| route] bvibvi_number
Syntax Description
| interface |
MRIB BVI interface. |
| route |
BVI route entry. |
| bvi_number |
BVI interface number. Range is from 1 to 65535. |
Command Default
None
Command Modes
EXEC
Command History
| Release | Modification |
|---|---|
| Release 5.1.1 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Task ID
| Task ID | Operation |
|---|---|
| multicast |
read |
Examples
This example shows how to run the show mrib bvi command:
RP/0/RSP0/CPU0:router # show mrib bvi route bvi 200
show mrib nsf
To display the state of nonstop forwarding (NSF) operation in the Multicast Routing Information Base (MRIB), use the show mrib nsf command in the appropriate mode.
show mrib ipv4 nsf
Syntax Description
|
ipv4 |
(Optional) Specifies IPv4 address prefixes. |
Command Default
IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The show mrib nsf command displays the current multicast NSF state for the MRIB. The state may be normal or activated for NSF. The activated state indicates that recovery is in progress due to a failure in MRIB or Protocol Independent Multicast (PIM). The total NSF timeout and time remaining are displayed until NSF expiration.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read |
Examples
The following is sample output from the show mrib nsf command:
RP/0/RSP0/CPU0:router# show mrib nsf
IP MRIB Non-Stop Forwarding Status:
Multicast routing state: Non-Stop Forwarding Activated
NSF Lifetime: 00:03:00
NSF Time Remaining: 00:01:40
|
Field |
Description |
|---|---|
|
Multicast routing state |
Multicast NSF status of the MRIB (Normal or NSF Activated). |
|
NSF Lifetime |
Timeout for MRIB NSF, computed as the maximum of the PIM and Internet Group Management Protocol (IGMP) NSF lifetimes, plus 60 seconds. |
|
NSF Time Remaining |
If MRIB NSF state is activated, the time remaining until MRIB reverts to Normal mode displays. Before this timeout, MRIB receives notifications from IGMP and PIM, triggering a successful end of NSF and cause the transition to normal state. If notifications are not received, the timer triggers a transition back to normal mode, causing new routes to download to MFIB and old routes to be deleted. |
Related Commands
|
Command |
Description |
|---|---|
|
Configures the NSF capability for the multicast routing system. |
|
|
nsf lifetime (IGMP) |
Configures the maximum time for the NSF timeout value under IGMP . |
|
nsf lifetime (PIM) |
Configures the NSF timeout value for the PIM process. |
|
show igmp nsf |
Displays the state of NSF operation in IGMP. |
|
show mfib nsf |
Displays the state of NSF operation in the MFIB line cards. |
|
show pim nsf |
Displays the state of NSF operation for PIM. |
show mrib route
To display all entries in the Multicast Routing Information Base (MRIB), use the show mrib route command in the appropriate mode .
show mrib [ vrf vrf-name ] [ ipv4 | ipv6 ] [old-output] route [ summary | outgoing-interface | [ * | source-address ] [ group-address [ /prefix-length ] ] ] [detail]
Syntax Description
|
vrf vrf-name |
(Optional) Specifies a VPN routing and forwarding (VRF) instance. |
|
ipv4 |
(Optional) Specifies IPv4 address prefixes. |
|
* |
(Optional) Displays shared tree entries. |
|
source-address |
(Optional) Source IP address or hostname of the MRIB route. Format is: A.B.C.D or X:X::X. |
|
group-address |
(Optional) Group IP address or hostname of the MRIB route. F ormat is: A.B.C.D or X:X::X. |
|
/prefix-length |
(Optional) Prefix length of the MRIB group address. A decimal value that indicates how many of the high-order contiguous bits of the address compose the prefix (the network portion of the address). A slash must precede the decimal value. Format is: A.B.C.D or X:X::X. |
|
outgoing-interface |
(Optional) Displays the outgoing-interface information. |
|
summary |
(Optional) Displays a summary of the routing database. |
|
detail |
(Optional) Displays the routing database with the platform data. |
Command Default
IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Each line card has an individual Multicast Forwarding Information Base (MFIB) table. The MFIB table maintains a subset of entries and flags updated from MRIB. The flags determine the forwarding and signaling behavior according to a set of forwarding rules for multicast packets. In addition to the list of interfaces and flags, each route entry shows various counters. Byte count is the number of total bytes forwarded. Packet count is the number of packets received for this entry.
The show mfib counter command displays global counters independent of the routes.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read |
Related Commands
|
Command |
Description |
|---|---|
|
Displays MFIB counter statistics for packets that have dropped. |
|
|
Displays the contents of the MRIB route collapse database. |
|
|
Displays all entries in the MFIB table. |
show mrib route-collapse
To display the contents of the Multicast Routing Information Base (MRIB) route-collapse database, use the show mrib route-collapse command in the appropriate mode.
show mrib [ vrf vrf-name ] ipv4 route-collapse [core-tree]
Syntax Description
|
vrf vrf-name |
(Optional) Specifies a VPN routing and forwarding (VRF) instance. |
|
ipv4 |
(Optional) Specifies IPv4 address prefixes. |
|
core-tree |
(Optional) IPv4 Multicast Distribution Tree (MDT) group address. |
Command Default
IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read |
Examples
The following is sample output from the show mrib route-collapse command:
RP/0/RSP0/CPU0:router# show mrib route-collapse
226.1.1.1 TID: 0xe0000038 TLC TID: 0xe0000038
Customer route database count: 5
(192.168.5.204,224.0.1.40/32)
(*,226.226.226.226/32)
(*,228.228.228.228/32)
(192.168.113.17,228.228.228.228/32)
(*,229.229.229.229/32)
Core route database count: 4
(*,226.1.1.1/32)
(192.168.5.201,226.1.1.1/32)
(192.168.5.202,226.1.1.1/32)
(192.168.5.204,226.1.1.1/32)
Core egress node database count: 1
nodeid slot refcount
0x20 0/2/CPU0 1
192.168.27.1 TID: 0xe0000039 TLC TID: 0xe0000039
Customer route database count: 1
(192.168.113.33,227.227.227.227/32)
Core route database count: 3
(*,227.27.27.1/32)
(192.168.5.201,227.27.27.1/32)
(192.168.5.202,227.27.27.1/32)
Core egress node database count: 1
nodeid slot refcount
0x20 0/2/CPU0 1
192.168.28.1 TID: 0xe000003a TLC TID: 0xe000003a
Customer route database count: 2
(192.168.5.204,224.0.1.40/32)
(192.168.113.49,229.229.229.229/32)
Core route database count: 3
(192.168.5.201,228.28.28.1/32)
(192.168.5.202,228.28.28.1/32)
(192.168.5.204,228.28.28.1/32)
Core egress node database count: 1
nodeid slot refcount
0x20 0/2/CPU0 1
Related Commands
Command | Description |
| Displays all entries in the Multicast Routing Information Base (MRIB). |
show mrib route outgoing-interface
To display the outgoing-interface information on the Multicast Routing Information Base (MRIB), use the show mrib route outgoing-interface command in the appropriate mode.
show mrib route outgoing-interface [ * | source-address ] [ group-address [ /prefix-length ] ]
Syntax Description
|
* |
(Optional) Displays shared tree entries. |
|
A.B.C.D |
(Optional) Source IP address or hostname of the MRIB route. Format is: A.B.C.D |
|
A.B.C.D |
(Optional) Group IP address or hostname of the MRIB route and the prefix length. |
|
/prefix-length |
(Optional) Prefix length of the MRIB group address. A decimal value that indicates how many of the high-order contiguous bits of the address compose the prefix (the network portion of the address). A slash must precede the decimal value. Format is: A.B.C.D |
Command Default
IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
|
Release 3.9.0 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read |
Examples
The following is sample output from the show mrib route outgoing-interface command:
RP/0/RSP0/CPU0:router# show mrib route outgoing-interface IP Multicast Routing Information Base Entry flags: L - Domain-Local Source, E - External Source to the Domain, C - Directly-Connected Check, S - Signal, IA - Inherit Accept, IF - Inherit From, D - Drop, MA - MDT Address, ME - MDT Encap, MD - MDT Decap, MT - MDT Threshold Crossed, MH - MDT interface handle CD - Conditional Decap, MPLS - MPLS Decap, MF - MPLS Encap, EX - Extranet MoFE - MoFRR Enabled, MoFS - MoFRR State (*,224.0.0.0/4), Up:6d10h, OIF count:0, flags: C (*,224.0.0.0/24), Up:6d10h, OIF count:0, flags: D (*,224.0.1.39), Up:6d10h, OIF count:3, flags: S (10.1.1.1,224.0.1.39), Up:6d10h, OIF count:11, flags: (10.2.2.2,224.0.1.39), Up:6d10h, OIF count:11, flags: (10.3.3.3,224.0.1.39), Up:6d10h, OIF count:11, flags: (10.4.4.4,224.0.1.39), Up:6d10h, OIF count:11, flags: (10.5.5.5,224.0.1.39), Up:6d10h, OIF count:11, flags: (10.6.6.6,224.0.1.39), Up:6d10h, OIF count:11, flags: (10.7.7.7,224.0.1.39), Up:00:04:17, OIF count:11, flags: (10.8.8.8,224.0.1.39), Up:6d10h, OIF count:11, flags: (10.9.9.9,224.0.1.39), Up:6d10h, OIF count:11, flags: (10.10.10.10,224.0.1.39), Up:6d10h, OIF count:11, flags: (10.21.21.21,224.0.1.39), Up:6d06h, OIF count:11, flags: (*,224.0.1.40), Up:6d10h, OIF count:2, flags: S (10.1.1.1,224.0.1.40), Up:6d10h, OIF count:11, flags: (10.2.2.2,224.0.1.40), Up:6d10h, OIF count:11, flags: (10.6.6.6,224.0.1.40), Up:6d10h, OIF count:11, flags: (10.13.4.3,224.0.1.40), Up:6d10h, OIF count:11, flags: (10.14.4.4,224.0.1.40), Up:6d10h, OIF count:11, flags: (10.14.8.4,224.0.1.40), Up:6d10h, OIF count:11, flags: (10.21.21.21,224.0.1.40), Up:6d06h, OIF count:11, flags: (10.23.4.3,224.0.1.40), Up:00:02:38, OIF count:11, flags: (10.23.8.3,224.0.1.40), Up:00:02:38, OIF count:11, flags: (10.34.4.3,224.0.1.40), Up:6d10h, OIF count:11, flags: (10.34.8.3,224.0.1.40), Up:6d10h, OIF count:11, flags: (10.35.4.3,224.0.1.40), Up:00:02:38, OIF count:11, flags: (10.35.4.5,224.0.1.40), Up:6d10h, OIF count:11, flags: (10.38.4.8,224.0.1.40), Up:6d10h, OIF count:11, flags: (10.45.4.5,224.0.1.40), Up:6d10h, OIF count:11, flags: (10.49.4.9,224.0.1.40), Up:6d10h, OIF count:11, flags: (10.105.4.10,224.0.1.40), Up:6d10h, OIF count:11, flags: (*,225.0.0.0/8), Up:6d06h, OIF count:0, flags: C (*,226.0.0.0/8), Up:6d06h, OIF count:0, flags: C (*,232.0.0.0/8), Up:6d10h, OIF count:0, flags: D (10.6.6.6,232.1.1.1), Up:6d10h, OIF count:3, flags: (10.7.7.7,232.1.1.1), Up:6d10h, OIF count:2, flags: (10.8.8.8,232.1.1.1), Up:6d10h, OIF count:2, flags: (10.9.9.9,232.1.1.1), Up:6d10h, OIF count:2, flags: (10.10.10.10,232.1.1.1), Up:6d10h, OIF count:2, flags: (10.21.21.21,232.1.1.1), Up:6d06h, OIF count:3, flags:
Related Commands
Command | Description |
| Displays all entries in the Multicast Routing Information Base (MRIB). |
show mrib table-info
To display Multicast Routing Information Base (MRIB) table information, use the show mrib table-info command in the appropriate mode.
show mrib [ vrf vrf-name ] ipv4 table-info
Syntax Description
|
vrf vrf-name |
(Optional) Specifies a VPN routing and forwarding (VRF) instance. |
|
ipv4 |
(Optional) Specifies IPv4 address prefixes. |
Command Default
IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read |
Examples
The following is sample output from the show mrib table-info command:
RP/0/RSP0/CPU0:router# show mrib vrf vrf101 table-info VRF: default [tid 0xe0000000] Registered Client: igmp [ccbid: 0 cltid: 4485366] pim [ccbid: 1 cltid: 4485368] bcdl_agent [ccbid: 2 cltid: 1] msdp [ccbid: 3 cltid: 8827135]
|
Field |
Description |
|---|---|
|
VRF |
Default VRF or a VRF configured for the purpose of an override in MVPN. |
|
cltid |
Client ID. |
|
bcdl_agent |
A process like igmp and pim, which is used to download routes to line card. |
|
MDT handle |
MDT interface handle for this VRF. |
|
MDT group |
Default MDT group associated with this VRF. |
|
MDT source |
Per-VRF MDT source information. |
Related Commands
Command | Description |
| Displays the contents of the Multicast Routing Information Base (MRIB) table-line card (TLC) database. |
show mrib tlc
To display the contents of the Multicast Routing Information Base (MRIB) table-line card (TLC) database, use the show mrib tlc command in the appropriate mode .
show mrib [ vrf vrf-name ] ipv4 tlc
Syntax Description
|
vrf vrf-name |
(Optional) Specifies a VPN routing and forwarding (VRF) instance. |
|
ipv4 |
(Optional) Specifies IPv4 address prefixes. |
Command Default
IPv4 addressing is the default.
Command Modes
EXEC
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read |
Examples
The following is sample output from the show mrib tlc command:
RP/0/RSP0/CPU0:router# show mrib tlc VRF: default [tid 0xe0000000] Master LC slot: Not selected Associated MDT group: 0 Forwarding LC node: 0
|
Field |
Description |
|---|---|
|
Associated MDT group |
IP address of the MSDP peer. |
|
Master LC slot |
Indicates whether the master LC slot has been selected. |
|
Forwarding LC node |
Autonomous system to which the peer belongs. |
|
Associated MDT group |
Indicates the number of associated MDT groups. |
static-rpf
To configure a static Reverse Path Forwarding (RPF) rule for a specified prefix mask, use the static-rpf command in an appropriate configuration mode. To return to the default behavior, use the no form of this command.
static-rpf prefix-address prefix-mask type path-id next-hop-address
no static-rpf
Syntax Description
|
prefix-address |
IP address of a prefix for an address range. |
||
|
prefix-mask |
Prefix mask for an address range. Range is 0 to 32 for IPv4 . |
||
|
type |
Interface type. For more information, use the question mark (?) online help function. |
||
|
interface-path-id |
Physical interface or virtual interface.
For more information about the syntax for the router, use the question mark ( ? ) online help function. |
||
|
next-hop-address |
IP address for an RPF neighbor. |
Command Default
A static RPF rule for a specified prefix mask is not configured.
Command Modes
Multicast routing address family ipv4 and ipv6 configuration
Multicast VRF configuration
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
The static-rpf command is used to configure incompatible topologies for unicast and multicast traffic.
Use the static-rpf command to configure a static route to be used for RPF checking in Protocol Independent Multicast (PIM) instead of using the unicast routing table.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write |
Examples
The following example configures the static RPF rule for IP address 10.0.0.1:
RP/0/RSP0/CPU0:router(config)# multicast-routing RP/0/RSP0/CPU0:router(config-mcast)# vrf green RP/0/RSP0/CPU0:router(config-mcast)# static-rpf 10.0.0.1 32 GigE 0/0/5/0 10.1.1.1
Related Commands
|
Command |
Description |
|---|---|
|
show pim context |
Displays reverse path forwarding (RPF) table information configured for a VRF context. |
source-tree-prune-delay
To set the delay-time for the (S,G) prune of the ingress-PE (provider edge), use the source-tree-prune-delay command in the appropriate mode. To remove the set delay, use the noform of the command.
source-tree-prune-delay time
nosource-tree-prune-delay time
Syntax Description
| time |
Delay in seconds. Range is 0 to 300. |
Command Default
60 seconds
Command Modes
C-multicast-routing configuration mode
Command History
| Release | Modification |
|---|---|
|
Release 4.3 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
This command is used to delay (S,G) Prune on the Ingress-PE, when the last Type-7 route is withdrawn.
Task ID
| Task ID | Operation |
|---|---|
| multicast |
read, write |
Examples
This example shows how to use the source-tree-prune-delay command:
RP/0/RSP0/CPU0:router (config-pim-v1-ipv4-mdt-cmcast) # source-tree-prune-delay 100
suppress-pim-data-signaling
To suppress PIM data signaling, use the suppress-pim-data-signaling command in the appropriate mode. To remove the suppressed condition, use the no form of the command.
suppress-pim-data-signaling
nosuppress-pim-data-signaling
Syntax Description
This command has no keywords or arguments.
Command Default
None
Command Modes
PIM C-multicast routing configuration mode
Command History
| Release | Modification |
|---|---|
|
Release 4.3 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
This command supports c-anycast RP and can be used only under the PIM c-multicast routing mode.
Task ID
| Task ID | Operation |
|---|---|
| multicast |
read, write |
Examples
This example shows how to use the suppress-pim-data-signalingcommand:
RP/0/RSP0/CPU0:router (config-pim-v1-ipv4-mdt-cmcast) # suppress-pim-data-signaling
suppress-shared-tree-join
To suppress shared tree joins and support the SPT-only mode, use the suppress-shared-tree-join command in the appropriate mode.
To remove the suppress condition, use the noform of the command.suppress-shared-tree-join
nosuppress-shared-tree-join
Syntax Description
This command has no keywords or arguments.
Command Default
None
Command Modes
C-multicast-routing configuration mode
Command History
| Release | Modification |
|---|---|
|
Release 4.3 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
This command enables the SPT-only (Shortest Path Tree) mode.
Task ID
| Task ID | Operation |
|---|---|
| multicast |
read, write |
Examples
This command shows how to use the suppress-shared-tree-join command:
RP/0/RSP0/CPU0:router(config-pim-v1-ipv4-mdt-cmcast) # suppress-shared-tree-join
ttl-threshold (multicast)
To configure the time-to-live (TTL) threshold for packets being forwarded out an interface, use the ttl-threshold command in the appropriate configuration mode. To return to the default behavior, use the no form of this command.
ttl-threshold ttl
no ttl-threshold ttl
Syntax Description
|
ttl |
Time to live value. Range is 1 to 255. |
Command Default
ttl : 0
Command Modes
Multicast routing interface configuration
Multicast routing VRF interface configuration
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
Only multicast packets with a TTL value greater than the threshold are forwarded out of the interface. The TTL threshold is compared to the TTL of the packet after it has been decremented by one and before being forwarded.
Configure the TTL threshold only on border routers.
Note | Do not confuse this command with the ttl-threshold (MSDP) command in router MSDP configuration mode that is used to confine the multicast data packet TTL to be sent by an Multicast Source Discovery Protocol (MSDP) Source-Active (SA) message. |
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write |
Examples
The following example shows how to configure the TTL threshold to 23, which means that a multicast packet is dropped and not forwarded out of the GigE 0/1/0/0 interface:
RP/0/RSP0/CPU0:router(config)# multicast-routing RP/0/RSP0/CPU0:router(config-mcast)# interface GigE 0/1/0/CPU0 RP/0/RSP0/CPU0:router(config-mcast-default-ipv4-if)# ttl-threshold 23
Related Commands
|
Command |
Description |
|---|---|
|
ttl-threshold (MSDP) |
Limits which multicast data packets are sent in SA messages to an MSDP peer. |
unicast-reachability
To disable VPN-IP attributes, use the unicast-reachability command in the appropriate mode. To restore the attributes, use the noform of the command.
unicast-reachability [ connector-disable | source-as-disable | vrf-route-import-disable ]
nounicast-reachability [ connector-disable | source-as-disable | vrf-route-import-disable ]
Syntax Description
| connector-disable |
Disables connector addition. |
| source-as-disable |
Disables source AS extended community addition. |
| vrf-route-import-disable |
Disables VRF route import extended community addition. |
Command Default
None
Command Modes
C-multicast routing configuration mode
Command History
| Release | Modification |
|---|---|
|
Release 4.3 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
This command controls addition of extended communities to unicast VPN-IP routes. These attributes have specific purposes in PIM and BGP C-multicast Routing.
Task ID
| Task ID | Operation |
|---|---|
| multicast |
read, write |
Examples
This example shows how to use the unicast-reachability command:
RP/0/RSP0/CPU0:router (config-pim-v1-ipv4-mdt-cmcast) # unicast-reachability connector-disable
vrf (multicast)
To configure a virtual routing and forwarding (VRF) instance for a VPN table, use the vrf command in multicast routing configuration mode. To remove the VRF instance from the configuration file and restore the system to its default condition, use the no form of this command.
vrf vrf-name ipv4
no vrf vrf-name ipv4
Syntax Description
|
vrf-name |
Name of the VRF instance. The following names cannot be used: all, default, and global. |
|
ipv4 |
(Optional) Configures IPv4 address prefixes. |
Command Default
No default behavior or values.
Command Modes
Multicast routing configuration
Command History
|
Release |
Modification |
|---|---|
|
Release 3.7.2 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
A VRF instance is a collection of VPN routing and forwarding tables maintained at the provider edge (PE) router.
Task ID
|
Task ID |
Operations |
|---|---|
|
multicast |
read, write |
Examples
The following example shows how to configure a VRF instance and enter VRF configuration mode:
RP/0/RSP0/CPU0:router(config)# multicast-routing RP/0/RSP0/CPU0:router(config-mcast)# vrf vrf_1 RP/0/RSP0/CPU0:router(config-mcast-vrf_1-ipv4)# mdt ? data Data MDT group configuration default MDT default group address mtu MDT mtu configuration source Interface used to set MDT source address
Related Commands
|
Command |
Description |
|---|---|
|
Configures a boundary to keep multicast packets from being forwarded. |
|
|
Enables per-prefix counters only in hardware. |
|
|
Configures multicast interface properties. |
|
|
Enables logging of trap events. |
|
|
Enables Protocol Independent Multicast (PIM) to divide the multicast load among several equal-cost paths. |
|
|
Enables individual (source, group [S, G]) rate calculations. |
|
|
ssm |
Defines the Protocol Independent Multicast (PIM)-Source Specific Multicast (SSM) range of IP multicast addresses. |
|
Configures a static Reverse Path Forwarding (RPF) rule for a specified prefix mask. |
Feedback