System Setup and Software Installation Guide for Cisco NCS 1014, IOS XR Release 7.11.x

Inventory Support in NCS 1014

Table 1. Feature History
Feature Name	Release Information	Description
Inventory Support	Cisco IOS XR Release 7.11.1	Inventory support and pluggable optics support for QSFP28,QSFP-DD and Coherent Interface Module (CIM 8) are enabled in NCS 1014 system.

The NCS 1014 inventory model consists of the following components.

One NCS 1014 controller card.
NCS 1014 chassis.
Two AC or DC power supply units (PSU) of 2KW and 2.5KW.
Three FAN trays.
Four line cards.

The components are connected to a 2RU chassis. NCS 1014 can support upto four line cards at once at any given point in time. The line cards supported are , 1.2T, NCS1K4-2.4T-K9, CCMD-16-C and CCMD-16-L cards.

Note

CCMD-16-C: refers to the NCS1K14-CCMD-16-C card.

CCMD-16-L: refers to the NCS1K14-CCMD-16-L card.

1.2T : refers to the NCS1K4-1.2T-K9 C-band card.

2.4T: refers to the NCS1K4-2.4T-K9 C-band card.

The show inventory command retrieves and displays the inventory information about each Cisco product in the form of a Unique Device Identifier (UDI). The UDI is a combination of three separate data elements: a product identifier (PID), a version identifier (VID), and the serial number (SN). The PID is the name by which the product is ordered. It is also known as product name or part number.

The VID is the version of the product. Whenever a product is upgraded the VID gets incremented according to the changes added. The SN is the vendor based unique serial number assigned to any product. It is used to identifying any specific product.

Verify Inventory

The show inventory command displays the details of the hardware inventory of NCS 1014.

To verify the inventory information for all the physical entities, use the following command.

Note

The various options available under show inventory command are listed below.

Word: Partially qualified location specification
All: Inventory information for all the physical entities
Chassis: Inventory information about chassis
Details: Detailed entity information
Fan: Inventory information about fan
Location: Location of node for inventory
Power: Inventory information about power
Raw: Raw information
Vendor-type: Vendor type information

Example

RP/0/RP0/CPU0:ios#show inventory ?
  WORD         Partially qualified location specification
  all          Inventory information for all the physical entities
  chassis      Inventory information about chassis
  details      detailed entity information
  fan          Inventory information about fan
  location     Location of node for inventory
  power        Inventory information about power
  raw          raw information
  vendor-type  vendor-type information
  |            Output Modifiers
  <cr>

Procedure

show inventory

When you execute this command in the Cisco IOS XR EXEC mode, it displays the summary of NCS 1014 inventory based on different card and optics pluggables on all the slots or ports.

Example:

RP/0/RP0/CPU0:ios# 
RP/0/RP0/CPU0:ios# show inventory 
Thu Oct  5 02:32:14.231 UTC

NAME: "Rack 0", DESCR: "Network Convergence System 1014 chassis with timing support"
PID: NCS1014           , VID: V00, SN: FCB2717B151

NAME: "0/RP0/CPU0", DESCR: "Network Convergence System 1014 Controller"
PID: NCS1K14-CNTLR-K9  , VID: V00, SN: FCB2718B1AX

NAME: "0/0/NXR0", DESCR: "NCS1K4 12x QSFP28 2 Trunk C-Band DWDM card"
PID: NCS1K4-1.2T-K9    , VID: V00, SN: CAT2250B0B9

NAME: "0/1/NXR0", DESCR: "Network Convergence System 1014 2.4T Line Card"
PID: NCS1K14-2.4T-K9   , VID: V00, SN: FCB2710B0L5

NAME: "Optics0/1/0/0", DESCR: "Cisco CIM8 C K9 Pluggable Optics Module"
PID: CIM8-C-K9         , VID: VES1, SN: SIM-AX12-SW

NAME: "Optics0/1/0/1", DESCR: "Cisco 100G QSFP28 SR4-S Pluggable Optics Module"
PID: QSFP-100G-SR4-S   , VID: ES1 , SN: AVF1933G18C     

NAME: "Optics0/1/0/2", DESCR: "Non-Cisco UNKNOWN TYPE Pluggable Optics Module"
PID: TR-IQ13L-N00      , VID: 1B, SN: INFBH1940242    

NAME: "Optics0/1/0/3", DESCR: "Cisco UNKNOWN TYPE Pluggable Optics Module"
PID: ONS-QSFP-4X10-MLR , VID: V01 , SN: INL21010375     

NAME: "Optics0/1/0/4", DESCR: "Cisco 100G QSFP28 SR4-S Pluggable Optics Module"
PID: QSFP-100G-SR4-S   , VID: ES1 , SN: AVF1933G16A     

NAME: "Optics0/1/0/6", DESCR: "Cisco QSFP DD 400G FR4 S Pluggable Optics Module"
PID: QDD-400G-FR4-S    , VID: V01 , SN: FIW250504DL

NAME: "Optics0/1/0/7", DESCR: "Cisco CIM8 C K9 Pluggable Optics Module"
PID: CIM8-C-K9         , VID: VES1, SN: ACA27370055

NAME: "0/2/NXR0", DESCR: "NCS1K4 12x QSFP28 2 Trunk C-Band DWDM card"
PID: NCS1K4-1.2T-K9    , VID: V03, SN: CAT2329B32K

NAME: "Optics0/2/0/10", DESCR: "Cisco QSFP28 100G CU1M Pluggable Optics Module"
PID: QSFP-100G-CU1M    , VID: V01 , SN: LCC2402GKJ3-B   

NAME: "Optics0/2/0/11", DESCR: "Cisco 100G QSFP28 LR-S Pluggable Optics Module"
PID: QSFP-100G-LR-S    , VID: ES0 , SN: FBN2321A013     

NAME: "Optics0/2/0/12", DESCR: "Cisco 100G QSFP28 AOC Pluggable Optics Module"
PID: QSFP-100G-AOC3M   , VID: V03 , SN: INL23302076-B   

NAME: "Optics0/2/0/13", DESCR: "Cisco 100G QSFP28 LR-S Pluggable Optics Module"
PID: QSFP-100G-LR-S    , VID: ES0 , SN: FBN2321A024     

NAME: "Optics0/2/0/3", DESCR: "Cisco QSFP28 100G CU1M Pluggable Optics Module"
PID: QSFP-100G-CU1M    , VID: V01 , SN: LCC2402GKJ3-A   

NAME: "Optics0/2/0/4", DESCR: "Cisco 100G QSFP28 CWDM4 Pluggable Optics Module"
PID: QSFP-100G-CWDM4-S , VID: V02 , SN: JFQ2210800T     

NAME: "Optics0/2/0/5", DESCR: "Cisco 100G QSFP28 AOC Pluggable Optics Module"
PID: QSFP-100G-AOC3M   , VID: V03 , SN: INL23302076-A   

NAME: "Optics0/2/0/6", DESCR: "Non-Cisco 100G QSFP28 CWDM4 Pluggable Optics Module"
PID: FTLC1152RGPL2-G2  , VID: A0, SN: UYL0AL9         

NAME: "Optics0/2/0/7", DESCR: "Non-Cisco 100G QSFP28 LR4 Pluggable Optics Module"
PID: FIM37700/171      , VID: 01, SN: 37700171ZZ00PK  

NAME: "Optics0/2/0/8", DESCR: "Cisco 100G QSFP28 LR4 Pluggable Optics Module"
PID: ONS-QSFP28-LR4    , VID: V01 , SN: FNS20520RM6     

NAME: "0/3/NXR0", DESCR: "Network Convergence System 1014 Filler"
PID: NCS1K14-BLANK     , VID: V01, SN: N/A
          
NAME: "0/FT0", DESCR: "Network Convergence System 1014 FAN Module"
PID: NCS1K14-FAN       , VID: V00, SN: FCB2720B15J

NAME: "0/FT1", DESCR: "Network Convergence System 1014 FAN Module"
PID: NCS1K14-FAN       , VID: V00, SN: FCB2720B15L

NAME: "0/FT2", DESCR: "Network Convergence System 1014 FAN Module"
PID: NCS1K14-FAN       , VID: V00, SN: FCB2720B15E

NAME: "0/PM0", DESCR: "Network Convergence System 1004 AC Power Supply Unit"
PID: NCS1K4-AC-PSU     , VID: V00, SN: POG2221CL0Z

NAME: "0/PM1", DESCR: "Network Convergence System 1004 AC Power Supply Unit"
PID: NCS1K4-AC-PSU     , VID: V01, SN: POG2505CL53
RP/0/RP0/CPU0:ios#  
RP/0/RP0/CPU0:ios#


RP/0/RP0/CPU0:ios#show inventory all
Mon Nov 27 11:01:53.452 UTC

NAME: "Rack 0", DESCR: "Network Convergence System 1014 chassis with timing support"
PID: NCS1014           , VID: V00, SN: FCB2717B13C

NAME: "0/RP0/CPU0", DESCR: "Network Convergence System 1014 Controller"
PID: NCS1K14-CNTLR-K9  , VID: V00, SN: FCB2723B0CX

NAME: "0/0/NXR0", DESCR: "Network Convergence System 1014 Filler"
PID: NCS1K14-BLANK     , VID: V01, SN: N/A

NAME: "0/1/NXR0", DESCR: "Network Convergence System 1014 Filler"
PID: NCS1K14-BLANK     , VID: V01, SN: N/A

NAME: "0/2/NXR0", DESCR: "Network Convergence System 1014 2.4T Line Card"
PID: NCS1K14-2.4T-K9   , VID: V00, SN: FCB2726B067

NAME: "Optics0/2/0/4", DESCR: "Cisco QSFP DD 400G DR4 S Pluggable Optics Module"
PID: QDD-400G-DR4-S    , VID: V01 , SN: CGC25512003

NAME: "Optics0/2/0/5", DESCR: "Cisco QSFP DD 400G FR4 S Pluggable Optics Module"
PID: QDD-400G-FR4-S    , VID: V01 , SN: CGC26371408

NAME: "Optics0/2/0/7", DESCR: "Cisco CIM8 C K9 Pluggable Optics Module"
PID: CIM8-C-K9         , VID: VES1, SN: ACA274500CR

NAME: "0/3/NXR0", DESCR: "Network Convergence System 1014 Filler"
PID: NCS1K14-BLANK     , VID: V01, SN: N/A

NAME: "0/FT0", DESCR: "Network Convergence System 1014 FAN Module"
PID: NCS1K14-FAN       , VID: V00, SN: FCB2720B192

NAME: "0/FT1", DESCR: "Network Convergence System 1014 FAN Module"
PID: NCS1K14-FAN       , VID: V00, SN: FCB2720B197

NAME: "0/FT2", DESCR: "Network Convergence System 1014 FAN Module"
PID: NCS1K14-FAN       , VID: V00, SN: FCB2720B19U

NAME: "0/PM0", DESCR: "Network Convergence System 1004 AC Power Supply Unit"
PID: NCS1K4-AC-PSU     , VID: V01, SN: POG2727CLP6

NAME: "0/PM1", DESCR: "Network Convergence System 1004 AC Power Supply Unit"
PID: NCS1K4-AC-PSU     , VID: V01, SN: POG2727CLKS
RP/0/RP0/CPU0:ios#
RP/0/RP0/CPU0:ios#
RP/0/RP0/CPU0:ios#

To display location based inventory details use this command.


RP/0/RP0/CPU0:ios#show inventory location 0/2/NXR0 
Thu Oct  5 02:35:30.251 UTC

NAME: "0/2/NXR0", DESCR: "NCS1K4 12x QSFP28 2 Trunk C-Band DWDM card"
PID: NCS1K4-1.2T-K9    , VID: V03, SN: CAT2329B32K

NAME: "Optics0/2/0/10", DESCR: "Cisco QSFP28 100G CU1M Pluggable Optics Module"
PID: QSFP-100G-CU1M    , VID: V01 , SN: LCC2402GKJ3-B   

NAME: "Optics0/2/0/11", DESCR: "Cisco 100G QSFP28 LR-S Pluggable Optics Module"
PID: QSFP-100G-LR-S    , VID: ES0 , SN: FBN2321A013     

NAME: "Optics0/2/0/12", DESCR: "Cisco 100G QSFP28 AOC Pluggable Optics Module"
PID: QSFP-100G-AOC3M   , VID: V03 , SN: INL23302076-B   

NAME: "Optics0/2/0/13", DESCR: "Cisco 100G QSFP28 LR-S Pluggable Optics Module"
PID: QSFP-100G-LR-S    , VID: ES0 , SN: FBN2321A024     

NAME: "Optics0/2/0/3", DESCR: "Cisco QSFP28 100G CU1M Pluggable Optics Module"
PID: QSFP-100G-CU1M    , VID: V01 , SN: LCC2402GKJ3-A   

NAME: "Optics0/2/0/4", DESCR: "Cisco 100G QSFP28 CWDM4 Pluggable Optics Module"
PID: QSFP-100G-CWDM4-S , VID: V02 , SN: JFQ2210800T     

NAME: "Optics0/2/0/5", DESCR: "Cisco 100G QSFP28 AOC Pluggable Optics Module"
PID: QSFP-100G-AOC3M   , VID: V03 , SN: INL23302076-A   
          
NAME: "Optics0/2/0/6", DESCR: "Non-Cisco 100G QSFP28 CWDM4 Pluggable Optics Module"
PID: FTLC1152RGPL2-G2  , VID: A0, SN: UYL0AL9         

NAME: "Optics0/2/0/7", DESCR: "Non-Cisco 100G QSFP28 LR4 Pluggable Optics Module"
PID: FIM37700/171      , VID: 01, SN: 37700171ZZ00PK  

NAME: "Optics0/2/0/8", DESCR: "Cisco 100G QSFP28 LR4 Pluggable Optics Module"
PID: ONS-QSFP28-LR4    , VID: V01 , SN: FNS20520RM6     
RP/0/RP0/CPU0:ios#


RP/0/RP0/CPU0:ios#
RP/0/RP0/CPU0:ios#show inventory location 0/1/NXR0 
Thu Oct  5 02:38:13.791 UTC

NAME: "0/1/NXR0", DESCR: "Network Convergence System 1014 2.4T Line Card"
PID: NCS1K14-2.4T-K9   , VID: V00, SN: FCB2710B0L5

NAME: "Optics0/1/0/0", DESCR: "Cisco CIM8 C K9 Pluggable Optics Module"
PID: CIM8-C-K9         , VID: VES1, SN: SIM-AX12-SW

NAME: "Optics0/1/0/1", DESCR: "Cisco 100G QSFP28 SR4-S Pluggable Optics Module"
PID: QSFP-100G-SR4-S   , VID: ES1 , SN: AVF1933G18C     

NAME: "Optics0/1/0/2", DESCR: "Non-Cisco UNKNOWN TYPE Pluggable Optics Module"
PID: TR-IQ13L-N00      , VID: 1B, SN: INFBH1940242    

NAME: "Optics0/1/0/3", DESCR: "Cisco UNKNOWN TYPE Pluggable Optics Module"
PID: ONS-QSFP-4X10-MLR , VID: V01 , SN: INL21010375     

NAME: "Optics0/1/0/4", DESCR: "Cisco 100G QSFP28 SR4-S Pluggable Optics Module"
PID: QSFP-100G-SR4-S   , VID: ES1 , SN: AVF1933G16A     

NAME: "Optics0/1/0/6", DESCR: "Cisco QSFP DD 400G FR4 S Pluggable Optics Module"
PID: QDD-400G-FR4-S    , VID: V01 , SN: FIW250504DL

NAME: "Optics0/1/0/7", DESCR: "Cisco CIM8 C K9 Pluggable Optics Module"
PID: CIM8-C-K9         , VID: VES1, SN: ACA27370055
RP/0/RP0/CPU0:ios#  
RP/0/RP0/CPU0:ios#

To display chassis based inventory details use this command.


RP/0/RP0/CPU0:ios#show inventory chassis
Mon Nov 27 11:02:05.083 UTC

NAME: "Rack 0", DESCR: "Network Convergence System 1014 chassis with timing support"
PID: NCS1014           , VID: V00, SN: FCB2717B13C
RP/0/RP0/CPU0:ios#
RP/0/RP0/CPU0:ios#
RP/0/RP0/CPU0:ios#sh inventory details
Mon Nov 27 11:02:23.095 UTC

NAME: "Rack 0", DESCR: "Network Convergence System 1014 chassis with timing support"
PID: NCS1014           , VID: V00, SN: FCB2717B13C
MFG_NAME: Cisco Systems, Inc., SNMP_IDX: 8384513   , Type: Rack
PN: 800-111211-01, HW Ver: 0.1

NAME: "0/RP0/CPU0", DESCR: "Network Convergence System 1014 Controller"
PID: NCS1K14-CNTLR-K9  , VID: V00, SN: FCB2723B0CX
MFG_NAME: Cisco Systems, Inc., SNMP_IDX: 16385     , Type: Module
PN: 800-111209-01, HW Ver: 0.2

NAME: "0/0/NXR0", DESCR: "Network Convergence System 1014 Filler"
PID: NCS1K14-BLANK     , VID: V01, SN: N/A
MFG_NAME: Cisco Systems, Inc., SNMP_IDX: 1         , Type: Module
PN: 800-39505-01, HW Ver: 0.1

NAME: "0/1/NXR0", DESCR: "Network Convergence System 1014 Filler"
PID: NCS1K14-BLANK     , VID: V01, SN: N/A
MFG_NAME: Cisco Systems, Inc., SNMP_IDX: 4097      , Type: Module
PN: 800-39505-01, HW Ver: 0.1

NAME: "0/2/NXR0", DESCR: "Network Convergence System 1014 2.4T Line Card"
PID: NCS1K14-2.4T-K9   , VID: V00, SN: FCB2726B067
MFG_NAME: Cisco Systems, Inc., SNMP_IDX: 8193      , Type: Module
PN: 800-51107-01, HW Ver: 0.1

NAME: "Optics0/2/0/4", DESCR: "Cisco QSFP DD 400G DR4 S Pluggable Optics Module"
PID: QDD-400G-DR4-S    , VID: V01 , SN: CGC25512003
MFG_NAME: CISCO-CIG         , SNMP_IDX: 3129345   , Type: Module
PN: 10-3320-01, HW Ver: 0.0

NAME: "Optics0/2/0/5", DESCR: "Cisco QSFP DD 400G FR4 S Pluggable Optics Module"
PID: QDD-400G-FR4-S    , VID: V01 , SN: CGC26371408
MFG_NAME: CISCO-CIG         , SNMP_IDX: 3133441   , Type: Module
PN: 10-3321-01, HW Ver: 0.0

NAME: "Optics0/2/0/7", DESCR: "Cisco CIM8 C K9 Pluggable Optics Module"
PID: CIM8-C-K9         , VID: VES1, SN: ACA274500CR
MFG_NAME: CISCO-ACACIA      , SNMP_IDX: 3141633   , Type: Module
PN: 10-100471-01, HW Ver: 0.0

NAME: "0/3/NXR0", DESCR: "Network Convergence System 1014 Filler"
PID: NCS1K14-BLANK     , VID: V01, SN: N/A
MFG_NAME: Cisco Systems, Inc., SNMP_IDX: 12289     , Type: Module
PN: 800-39505-01, HW Ver: 0.1

NAME: "0/FT0", DESCR: "Network Convergence System 1014 FAN Module"
PID: NCS1K14-FAN       , VID: V00, SN: FCB2720B192
MFG_NAME: Cisco Systems, Inc., SNMP_IDX: 28673     , Type: Fantray
PN: 800-111210-01, HW Ver: 0.1

NAME: "0/FT1", DESCR: "Network Convergence System 1014 FAN Module"
PID: NCS1K14-FAN       , VID: V00, SN: FCB2720B197
MFG_NAME: Cisco Systems, Inc., SNMP_IDX: 32769     , Type: Fantray
PN: 800-111210-01, HW Ver: 0.1

NAME: "0/FT2", DESCR: "Network Convergence System 1014 FAN Module"
PID: NCS1K14-FAN       , VID: V00, SN: FCB2720B19U
MFG_NAME: Cisco Systems, Inc., SNMP_IDX: 36865     , Type: Fantray
PN: 800-111210-01, HW Ver: 0.1

NAME: "0/PM0", DESCR: "Network Convergence System 1004 AC Power Supply Unit"
PID: NCS1K4-AC-PSU     , VID: V01, SN: POG2727CLP6
MFG_NAME: Cisco Systems, Inc., SNMP_IDX: 20481     , Type: Power Supply
PN: 341-100825-01, HW Ver: 0.1

NAME: "0/PM1", DESCR: "Network Convergence System 1004 AC Power Supply Unit"
PID: NCS1K4-AC-PSU     , VID: V01, SN: POG2727CLKS
MFG_NAME: Cisco Systems, Inc., SNMP_IDX: 24577     , Type: Power Supply
PN: 341-100825-01, HW Ver: 0.1
RP/0/RP0/CPU0:ios#
RP/0/RP0/CPU0:ios#
RP/0/RP0/CPU0:ios#

To display fan based inventory details use this command.


RP/0/RP0/CPU0:ios#show inventory fan
Mon Nov 27 11:02:39.811 UTC

NAME: "0/FT0", DESCR: "Network Convergence System 1014 FAN Module"
PID: NCS1K14-FAN       , VID: V00, SN: FCB2720B192

NAME: "0/FT1", DESCR: "Network Convergence System 1014 FAN Module"
PID: NCS1K14-FAN       , VID: V00, SN: FCB2720B197

NAME: "0/FT2", DESCR: "Network Convergence System 1014 FAN Module"
PID: NCS1K14-FAN       , VID: V00, SN: FCB2720B19U
RP/0/RP0/CPU0:ios#
RP/0/RP0/CPU0:ios#
RP/0/RP0/CPU0:ios#sh inventory location 0/3/NXR0
Mon Nov 27 11:02:46.903 UTC

NAME: "0/3/NXR0", DESCR: "Network Convergence System 1014 Filler"
PID: NCS1K14-BLANK     , VID: V01, SN: N/A
RP/0/RP0/CPU0:ios#
RP/0/RP0/CPU0:ios#
RP/0/RP0/CPU0:ios#sh inventory power
Mon Nov 27 11:03:04.566 UTC

NAME: "0/PM0", DESCR: "Network Convergence System 1004 AC Power Supply Unit"
PID: NCS1K4-AC-PSU     , VID: V01, SN: POG2727CLP6

Verify Status of Hardware Components

To verify the status of all the hardware components installed on NCS 1014, perform the following procedure.

Before you begin

Ensure that all the required hardware components are installed on NCS 1014. For installation details, see Cisco Network Convergence System 1014 Hardware Installation Guide.

Procedure

Step 1

show platform

When you execute this command from the Cisco IOS XR EXEC mode, the status of Cisco IOS XR is displayed.

Example:

RP/0/RP0/CPU0:ios#show platform
Node              Type                     State                    Config state
--------------------------------------------------------------------------------
0/RP0/CPU0        NCS1K14-CNTLR-K9(Active) IOS XR RUN               NSHUT,NMON
0/PM0             NCS1K4-AC-PSU            OPERATIONAL              NSHUT,NMON
0/PM1             NCS1K4-AC-PSU            OPERATIONAL              NSHUT,NMON
0/FT0             NCS1K14-FAN              OPERATIONAL              NSHUT,NMON
0/FT1             NCS1K14-FAN              OPERATIONAL              NSHUT,NMON
0/FT2             NCS1K14-FAN              OPERATIONAL              NSHUT,NMON
0/0/NXR0          NCS1K4-1.2T-K9           OPERATIONAL              NSHUT,NMON
0/1/NXR0          NCS1K14-2.4T-K9          OPERATIONAL              NSHUT,NMON
0/2/NXR0          NCS1K4-1.2T-K9           OPERATIONAL              NSHUT,NMON
0/3/NXR0          NCS1K4-1.2T-K9           OPERATIONAL              NSHUT,NMON

Step 2

show inventory

Displays details of the physical entities of NCS 1014 along with the details of QSFPs when you execute this command in Cisco IOS XR EXEC mode.

Example:

RP/0/RP0/CPU0:ios#show platform
Node              Type                     State                    Config state
--------------------------------------------------------------------------------
0/RP0/CPU0        NCS1K14-CNTLR-K9(Active) IOS XR RUN               NSHUT,NMON
0/PM0             NCS1K4-AC-PSU            OPERATIONAL              NSHUT,NMON
0/PM1             NCS1K4-AC-PSU            OPERATIONAL              NSHUT,NMON
0/FT0             NCS1K14-FAN              OPERATIONAL              NSHUT,NMON
0/FT1             NCS1K14-FAN              OPERATIONAL              NSHUT,NMON
0/FT2             NCS1K14-FAN              OPERATIONAL              NSHUT,NMON
0/0/NXR0          NCS1K4-1.2T-K9           OPERATIONAL              NSHUT,NMON
0/1/NXR0          NCS1K14-2.4T-K9          OPERATIONAL              NSHUT,NMON
0/2/NXR0          NCS1K4-1.2T-K9           OPERATIONAL              NSHUT,NMON
0/3/NXR0          NCS1K4-1.2T-K9           OPERATIONAL              NSHUT,NMON


Step 2	show inventory

RP/0/RP0/CPU0:ios#show inventory 

NAME: "Rack 0", DESCR: "Network Convergence System 1014 chassis with timing support"
PID: NCS1014           , VID: V00, SN: FCB2726B0AR

NAME: "0/RP0/CPU0", DESCR: "Network Convergence System 1014 Controller"
PID: NCS1K14-CNTLR-K9  , VID: V00, SN: FCB2726B0LR

NAME: "0/0/NXR0", DESCR: "NCS1K4 12x QSFP28 2 Trunk C-Band DWDM card"
PID: NCS1K4-1.2T-K9    , VID: V00, SN: CAT2250B0C4

NAME: "Optics0/0/0/9", DESCR: "Cisco 100G QSFP28 FR-S Pluggable Optics Module"
PID: QSFP-100G-FR-S    , VID: V02 , SN: FBN2638A153     

NAME: "Optics0/0/0/10", DESCR: "Cisco 100G QSFP28 FR-S Pluggable Optics Module"
PID: QSFP-100G-FR-S    , VID: V02 , SN: FBN2638A6J0     

NAME: "Optics0/0/0/11", DESCR: "Cisco 100G QSFP28 FR-S Pluggable Optics Module"
PID: QSFP-100G-FR-S    , VID: V02 , SN: FBN2638A73V     

NAME: "Optics0/0/0/12", DESCR: "Cisco 100G QSFP28 FR-S Pluggable Optics Module"
PID: QSFP-100G-FR-S    , VID: V02 , SN: FBN2544A687     

NAME: "Optics0/0/0/13", DESCR: "Cisco 100G QSFP28 FR-S Pluggable Optics Module"
PID: QSFP-100G-FR-S    , VID: V02 , SN: FBN2638A2D4     

NAME: "Optics0/0/0/2", DESCR: "Cisco 100G QSFP28 LR4 Pluggable Optics Module"
PID: ONS-QSFP28-LR4    , VID: V01 , SN: FNS2333080H     

NAME: "Optics0/0/0/3", DESCR: "Cisco 100G QSFP28 FR-S Pluggable Optics Module"
PID: QSFP-100G-FR-S    , VID: V02 , SN: FBN2638A6J2     

NAME: "Optics0/0/0/4", DESCR: "Cisco 100G QSFP28 FR-S Pluggable Optics Module"
PID: QSFP-100G-FR-S    , VID: V01 , SN: INL23243050     

NAME: "Optics0/0/0/5", DESCR: "Cisco 100G QSFP28 LR4 Pluggable Optics Module"
PID: ONS-QSFP28-LR4    , VID: V01 , SN: FNS23320DZF     

NAME: "Optics0/0/0/6", DESCR: "Cisco 100G QSFP28 LR4 Pluggable Optics Module"
PID: ONS-QSFP28-LR4    , VID: V01 , SN: FNS26140JRK     

NAME: "Optics0/0/0/7", DESCR: "Cisco 100G QSFP28 LR4-S Pluggable Optics Module"
PID: QSFP-100G-LR4-S   , VID: V02 , SN: FNS263509QL     

NAME: "Optics0/0/0/8", DESCR: "Cisco 100G QSFP28 FR-S Pluggable Optics Module"
PID: QSFP-100G-FR-S    , VID: V02 , SN: FBN2638A5G5     

NAME: "0/1/NXR0", DESCR: "Network Convergence System 1014 2.4T Line Card"
PID: NCS1K14-2.4T-K9   , VID: V00, SN: FCB2726B072

Verify Software Version

NCS 1014 is shipped with the Cisco IOS XR Software preinstalled. Verify that the latest version of the software is installed.

Procedure

show version

Displays the software version and details such as system uptime.

Example:

RP/0/RP0/CPU0:ios#sh version 
Cisco IOS XR Software, Version 7.11.1.49I LNT
Copyright (c) 2013-2023 by Cisco Systems, Inc.

Build Information:
 Built By     : sajshah
 Built On     : Sun Nov 19 20:31:06 UTC 2023
 Build Host   : iox-ucs-077
 Workspace    : /auto/ioxdepot6/GISO/giso_build_lindt/giso_eng_create/yshivapp_2023-11-20_04-28-49_UTC
 Version      : 7.11.1.49I
 Label        : 7.11.1.49I-Weekly

cisco NCS1010 (C3758R @ 2.40GHz)
cisco NCS1014 (C3758R @ 2.40GHz) processor with 32GB of memory
KEPLER_PF6 uptime is 1 hour, 40 minutes
NCS 1014 - Chassis

Verify Environmental Parameters

The show environment command displays the environmental parameters of NCS 1014.

The following example shows sample output of the show environment command with the fan keyword.

RP/0/RP0/CPU0:ios#show environment fan
=============================================================
                                              Fan speed (rpm)
Location      FRU Type                        FAN_0    FAN_1
-------------------------------------------------------------

0/PM0        NCS1K4-DC-PSU-2                   11520   11216
0/PM1        NCS1K4-DC-PSU-2                   12256   12128
0/FT0        NCS1K14-FAN                       11400    9960
0/FT1        NCS1K14-FAN                       11340    9960
0/FT2        NCS1K14-FAN                       11400    9960

The following example shows sample output of the show environment command with the power keyword.

RP/0/RP0/CPU0:ios#sh environment power 
Tue Nov 28 14:14:52.169 UTC
================================================================================
CHASSIS LEVEL POWER INFO: 0
================================================================================
   Total output power capacity (Group 0 + Group 1) :    2000W +     2000W
   Total output power required                     :    1896W
   Total power input                               :     741W
   Total power output                              :     653W

Power Group 0:
================================================================================
   Power       Supply         ------Input----   ------Output---     Status
   Module      Type            Volts     Amps    Volts     Amps    
================================================================================
   0/PM0       NCS1K4-AC-PSU   224.0     1.8     12.1      28.9     OK

Total of Group 0:              403W/1.8A         349W/28.9A

Power Group 1:
================================================================================
   Power       Supply         ------Input----   ------Output---     Status
   Module      Type            Volts     Amps    Volts     Amps    
================================================================================
   0/PM1       NCS1K4-AC-PSU   225.2     1.5     12.1      25.2     OK

Total of Group 1:              337W/1.5A         304W/25.2A

================================================================================
   Location     Card Type               Power       Power        Status
                                        Allocated   Used
                                        Watts       Watts
================================================================================
   0/FT0        NCS1K14-FAN             170         27           ON
   0/FT1        NCS1K14-FAN             170         27           ON
   0/FT2        NCS1K14-FAN             170         28           ON
   0/0/NXR0     NCS1K4-1.2T-K9          260         220          ON
   0/1/NXR0     NCS1K4-1.2T-K9          260         221          ON
   0/2/NXR0     NCS1K4-1.2T-K9          260         54           ON
   0/3/NXR0     NCS1K14-2.4T-K9         460         15           ON
   0/Rack       NCS1014                 73          14           ON

The following example shows sample output of the show environment command with the temperature keyword.

RP/0/RP0/CPU0:ios#show environment temperature location 0/rp0/CPU0
================================================================================                                                                                                             =============================
Location  TEMPERATURE                          Value     Crit    Major    Minor                                                                                                                 Minor    Major    Crit
          Sensor                             (deg C)     (Lo)     (Lo)     (Lo)                                                                                                                  (Hi)     (Hi)    (Hi)
--------------------------------------------------------------------------------                                                                                                             -----------------------------
0/RP0/CPU0
          RP_TEMP_PCB                            38      -10       -5        0                                                                                                                    80       85       90
          RP_TEMP_HOT_SPOT                       38      -10       -5        0                                                                                                                    80       85       90
          RP_TEMP_LTM4638_0                      38      -10       -5        0                                                                                                                    85       90       95
          RP_TEMP_LTM4644_0                      37      -10       -5        0                                                                                                                    85       90       95
          RP_TEMP_LTM4644_1                      38      -10       -5        0                                                                                                                    85       90       95
          RP_TEMP_LTM4638_1                      37      -10       -5        0                                                                                                                    80       90       95
          RP_TEMP_LTM4644_2                      38      -10       -5        0                                                                                                                    85       90       95
          RP_TEMP_LTM4638_2                      38      -10       -5        0                                                                                                                    80       90       95
          TEMP_CPU_DIE                           39      -10       -5        0                                                                                                                    80       85       90
          TEMP_DDR_DIMM                          39      -10       -5        0                                                                                                                    80       85       90
          TEMP_CPU_SSD                           48      -10       -5        0                                                                                                                    70       75       80
          TEMP_EITU_SSD                          39      -10       -5        0                                                                                                                    70       75       80

The following example shows sample output of the show environment command with the voltage keyword.

RP/0/RP0/CPU0:ios#show environment voltage location 0/rp0/cpu0
=============================================================================================================
Location  VOLTAGE                             Value      Crit    Minor    Minor     Crit
          Sensor                              (mV)       (Lo)    (Lo)     (Hi)      (Hi)
-------------------------------------------------------------------------------------------------------------
0/RP0/CPU0
          RP_ADM1266_12V0                     12035    10800    11280    12720    13200
          RP_ADM1266_1V8_CPU                   1801     1670     1750     1850     1930
          RP_ADM1266_1V24_VCCREF               1238     1150     1200     1280     1330
          RP_ADM1266_1V05_CPU                  1053      980     1020     1080     1120
          RP_ADM1266_1V2_DDR_VDDQ              1205     1120     1160     1240     1280
          RP_ADM1266_1V0_VCC_RAM               1123      650      700     1250     1300
          RP_ADM1266_1V0_VNN                    946      550      600     1250     1300
          RP_ADM1266_1V0_VCCP                   704      450      500     1250     1300
          RP_ADM1266_0V6_DDR_VTT                600      560      580      620      640
          RP_ADM1266_12V0_DB                  12028    10800    11280    12720    13200
          RP_ADM1266_3V3_STAND_BY_DB           3302     3069     3201     3399     3531
          RP_ADM1266_3V3_STAND_BY              3306     3070     3200     3400     3530
          RP_ADM1266_5V0_DB                    5000     4650     4850     5150     5350
          RP_ADM1266_3V3_DB                    3328     3069     3201     3399     3531
          RP_ADM1266_2V5_DB                    2507     2325     2425     2575     2675
          RP_ADM1266_1V8_DB                    1804     1674     1746     1854     1926
          RP_ADM1266_1V0_PHY                    997      930      970     1030     1070
          RP_ADM1266_5V0                       5048     4650     4850     5150     5350
          RP_ADM1266_3V3                       3330     3070     3200     3400     3530
          RP_ADM1266_2V5_PLL                   2516     2330     2430     2580     2680
          RP_ADM1266_2V5_FPGA                  2505     2330     2430     2580     2680
          RP_ADM1266_1V2_FPGA                  1196     1120     1160     1240     1280
          RP_ADM1266_3V3_CPU                   3332     3070     3200     3400     3530
          RP_ADM1266_2V5_CPU                   2498     2330     2430     2580     2680

The following example shows sample output of the show environment command with the current keyword.

RP/0/RP0/CPU0:ios#show environment current
=============================================================================================================
Location  CURRENT                              Value
          Sensor                               (mA)
-------------------------------------------------------------------------------------------------------------
0/RP0/CPU0
          RP_JMAC_1V0_VCCP_IMON                   0
          RP_JMAC_1V0_VNN_IMON                   93
          RP_JMAC_1V0_VCC_RAM_IMON                0
          RP_JMAC_1V2_DDR_VDDQ_IMON             156
          RP_CURRMON_LTM4638_0                  345
          RP_CURRMON_LTM4644_0                  145
          RP_CURRMON_LTM4644_1                  250
          RP_CURRMON_LTM4638_1                  199
          RP_CURRMON_DB                         455
0/0/NXR0
          IMON_CLI                             2979
          IMON_CTLPL                            974
          IMON_MODULE                         11270
          IMON_CDR                             3357
          SA_ADM1275_12V_IMON_LC              18624
0/1/NXR0
          IMON_CTLPL                            887
          IMON_CLI                             4587
          IMON_META0_IN0                        807
          IMON_META0_CORE_IOUT0                5648
          IMON_META0_CORE_IOUT1                4570
          IMON_META0_IN2                        669
          IMON_META0_CORE_IOUT2                3726
          IMON_META0_AVD_IOUT                  5085
          IMON_META1_IN0                        326
          IMON_META1_CORE_IOUT0                2566
          IMON_META1_CORE_IOUT1                1578
          IMON_META1_IN2                        650
          IMON_META1_CORE_IOUT2                3718
          IMON_META1_AVD_IOUT                  4593
          SA_ADM1275_12V_IMON_LC               9433
0/2/NXR0
          IMON_OPTM                             867
          IMON_CTLPL                            512
          SA_ADM1275_12V_IMON_LC               1209
0/3/NXR0
          IMON_CLI                             2867
          IMON_CTLPL                           1017
          IMON_MODULE                         11153
          IMON_CDR                             3457
          SA_ADM1275_12V_IMON_LC              17582
0/Rack
          SA_ADM1275_12V_IMON_CPU              1843
 --More--

This example shows sample output of the show environment command with the all keyword.

RP/0/RP0/CPU0:sanity_176#sh environment all
=============================================================================================================
Location  TEMPERATURE                          Value     Crit    Major    Minor    Minor    Major    Crit
          Sensor                             (deg C)     (Lo)     (Lo)     (Lo)     (Hi)     (Hi)    (Hi)
-------------------------------------------------------------------------------------------------------------
0/RP0/CPU0
          RP_TEMP_PCB                            31      -10       -5        0       80       85       90
          RP_TEMP_HOT_SPOT                       32      -10       -5        0       80       85       90
          RP_TEMP_LTM4638_0                      32      -10       -5        0       85       90       95
          RP_TEMP_LTM4644_0                      30      -10       -5        0       85       90       95
          RP_TEMP_LTM4644_1                      32      -10       -5        0       85       90       95
          RP_TEMP_LTM4638_1                      31      -10       -5        0       80       90       95
          RP_TEMP_LTM4644_2                      30      -10       -5        0       85       90       95
          RP_TEMP_LTM4638_2                      31      -10       -5        0       80       90       95
          TEMP_CPU_DIE                           36      -10       -5        0       80       85       90
          TEMP_DDR_DIMM                          33      -10       -5        0       80       85       90
          TEMP_CPU_SSD                           44      -10       -5        0       70       75       80
          TEMP_CHASSIS_SSD                       31      -10       -5        0       70       75       80
0/PM0
          Air Inlet Temperature                  30      -10       -5        0       62       67       72
          Air Outlet Temperature                 32      -10       -5        0       82       87       92
          Oring MOSFET                           35      -10       -5        0       77       82       87
0/PM1
          Air Inlet Temperature                  31      -10       -5        0       62       67       72
          Air Outlet Temperature                 32      -10       -5        0       82       87       92
          Oring MOSFET                           34      -10       -5        0       77       82       87
0/1/NXR0
          TEMP_DX_PCB                             -      -10       -5        0       95      100      105
          TEMP_DX_ZYNQ                            -      -10       -5        0       95      100      105
          SA_TEMP_OUTLET_LC                       -      -10       -5        0       75       85       90
0/3/NXR0
          TEMP_DX_PCB                            24      -10       -8       -5       85       90       95
          TEMP_DX_ZYNQ                           27      -10       -8       -5       95       98      100
          SA_TEMP_OUTLET_LC                      25      -10       -5        0       75       85       90
0/Rack
          SA_TEMP_CHASSIS_INLET0                 21      -10       -5        0       45       55       60
          SA_TEMP_CHASSIS_INLET1                 21      -10       -5        0       45       55       60
          SA_TEMP_LTM4647_HOTSPOT                32      -10       -5        0       95      105      110
          SA_TEMP_ALDRIN_HOTSPOT                 26      -10       -5        0       80       85       90
          SA_TEMP_INLET_PSU0                     30      -10       -5        0       80       85       90
          SA_TEMP_INLET_PSU1                     30      -10       -5        0       80       85       90
          SA_TEMP_INLET_FAN0                     25      -10       -5        0       80       85       90
          SA_TEMP_INLET_FAN1                     20      -10       -5        0       80       85       90
=============================================================================================================
Location  VOLTAGE                             Value      Crit    Minor    Minor     Crit
          Sensor                              (mV)       (Lo)    (Lo)     (Hi)      (Hi)
-------------------------------------------------------------------------------------------------------------
0/RP0/CPU0
          RP_ADM1266_12V0                     12050    10800    11280    12720    13200
          RP_ADM1266_3V3_STAND_BY              3304     3070     3200     3400     3530
          RP_ADM1266_5V0                       5056     4650     4850     5150     5350
          RP_ADM1266_3V3                       3334     3070     3200     3400     3530
          RP_ADM1266_2V5_PLL                   2515     2330     2430     2580     2680
          RP_ADM1266_2V5_FPGA                  2511     2330     2430     2580     2680
          RP_ADM1266_1V2_FPGA                  1202     1120     1160     1240     1280
          RP_ADM1266_3V3_CPU                   3332     307

Verify Management Interface Status

To verify the management interface status, perform the following procedure.

Procedure

show interfaces mgmtEth instance

Displays the management interface configuration.

Example:

RP/0/RP0/CPU0:ios#show interfaces MgmtEth 0/RP0/CPU0/0
MgmtEth0/RP0/CPU0/0 is up, line protocol is up 
  Interface state transitions: 3
  Hardware is Management Ethernet, address is 4014.82ba.d26e (bia 4014.82ba.d26e)
  Internet address is 10.105.57.37/25
  MTU 1514 bytes, BW 1000000 Kbit (Max: 1000000 Kbit)
     reliability 255/255, txload 0/255, rxload 0/255
  Encapsulation ARPA,
  Full-duplex, 1000Mb/s, CX, link type is autonegotiation
  loopback not set,
  Last link flapped 00:09:12
  ARP type ARPA, ARP timeout 04:00:00
  Last input 00:00:00, output 00:00:00
  Last clearing of "show interface" counters never
  5 minute input rate 1000 bits/sec, 2 packets/sec
  5 minute output rate 5000 bits/sec, 1 packets/sec
     6715 packets input, 640515 bytes, 0 total input drops
     0 drops for unrecognized upper-level protocol
     Received 2213 broadcast packets, 4430 multicast packets
              0 runts, 0 giants, 0 throttles, 0 parity
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     944 packets output, 355004 bytes, 0 total output drops
     Output 94 broadcast packets, 114 multicast packets
     0 output errors, 0 underruns, 0 applique, 0 resets
     0 output buffer failures, 0 output buffers swapped out
     3 carrier transitions

In the previous output, the management interface is administratively down.

You can also use the show interfaces summary and show interfaces brief commands in the Cisco IOS XR EXEC mode to verify the management interface status.

The following example shows sample output from the show interfaces summary command.

RP/0/RP0/CPU0:ios#show interfaces summary
Interface Type          Total    UP       Down     Admin Down
--------------          -----    --       ----     ----------
ALL TYPES               5        2        0        3       
--------------         
IFT_ETHERNET            2        1        0        1       
IFT_NULL                1        1        0        0       
IFT_PTP_ETHERNET        2        0        0        2

The following example shows sample output from the show interfaces brief command.

RP/0/RP0/CPU0:KEPLER_PF6#show interfaces brief

               Intf       Intf        LineP              Encap  MTU        BW
               Name       State       State               Type (byte)    (Kbps)
--------------------------------------------------------------------------------
                Nu0          up          up               Null  1500          0
     Mg0/RP0/CPU0/0          up          up               ARPA  1514    1000000
     Mg0/RP0/CPU0/1  admin-down  admin-down               ARPA  1514    1000000
     PT0/RP0/CPU0/0  admin-down  admin-down               ARPA  1514    1000000
     PT0/RP0/CPU0/1  admin-down  admin-down               ARPA  1514    1000000

What to do next

If the management interface is administratively down, perform the following steps:

Check the Ethernet cable connection.
Verify the IP configuration of the management interface. For details on configuring the management interface, see Configure Management Interface.
Verify whether the management interface is in the no shut state using the show running-config interface mgmtEth command.

The following example shows sample output from the show running-config interface mgmtEth command.
```
RP/0/RP0/CPU0:ios#show running-config interface mgmtEth 0/RP0/CPU0/0
interface MgmtEth0/RP0/CPU0/0
 ipv4 address 10.105.57.37 255.255.255.128
!
```

Verify Firmware Version

The firmware on various hardware components of NCS 1014 must be compatible with the installed Cisco IOS XR image. Incompatibility may cause the NCS 1014 to malfunction.

To verify the firmware version, perform the following procedure.

Before you begin

Procedure

Step 1

show hw-module fpd

Example:

RP/0/RP0/CPU0:ios#show hw-module fpdAuto-upgrade:Enabled
Attribute codes: B golden, P protect, S secure, A Anti Theft aware
                                                                         FPD Versions
                                                                        ==============
Location   Card type             HWver FPD device       ATR Status   Running Programd  Reload Loc
-------------------------------------------------------------------------------------------------
0/RP0/CPU0 NCS1K14-CNTLR-K9      0.2   ADM-DB               CURRENT    2.10    2.10       NOT REQ
0/RP0/CPU0 NCS1K14-CNTLR-K9      0.2   ADM-MB               CURRENT    2.30    2.30       NOT REQ
0/RP0/CPU0 NCS1K14-CNTLR-K9      0.2   BIOS             S   CURRENT    4.70    4.70         0/RP0
0/RP0/CPU0 NCS1K14-CNTLR-K9      0.2   BIOS-Golden      BS  CURRENT            4.70         0/RP0
0/RP0/CPU0 NCS1K14-CNTLR-K9      0.2   CpuFpga          S   CURRENT    1.09    1.09         0/RP0
0/RP0/CPU0 NCS1K14-CNTLR-K9      0.2   CpuFpgaGolden    BS  NEED UPGD          1.03         0/RP0
0/RP0/CPU0 NCS1K14-CNTLR-K9      0.2   SsdMicron5300    S   CURRENT    0.01    0.01         0/RP0
0/RP0/CPU0 NCS1K14-CNTLR-K9      0.2   TamFw            S   CURRENT    9.04    9.04         0/RP0
0/RP0/CPU0 NCS1K14-CNTLR-K9      0.2   TamFwGolden      BS  CURRENT            9.04         0/RP0
0/PM0      NCS1K4-AC-PSU         0.1   PO-PriMCU            CURRENT    2.04    2.04       NOT REQ
0/PM0      NCS1K4-AC-PSU         0.1   PO-SecMCU            CURRENT    2.06    2.06       NOT REQ
0/PM1      NCS1K4-AC-PSU         0.1   PO-PriMCU            CURRENT    2.04    2.04       NOT REQ
0/PM1      NCS1K4-AC-PSU         0.1   PO-SecMCU            CURRENT    2.06    2.06       NOT REQ
0/0/NXR0   NCS1K4-1.2T-K9        0.1   CpuModFw         S   CURRENT  234.10  234.10       NOT REQ
0/0/NXR0   NCS1K4-1.2T-K9        0.1   OptModFw         S   CURRENT    1.38    1.38       NOT REQ
0/1/NXR0   NCS1K14-2.4T-K9       0.1   CpuModFw         S   CURRENT  234.10  234.10       NOT REQ
0/2/NXR0   NCS1K4-1.2T-K9        0.1   CpuModFw         S   CURRENT  234.10  234.10       NOT REQ
0/2/NXR0   NCS1K4-1.2T-K9        0.1   OptModFw         S   CURRENT    1.38    1.38       NOT REQ
0/3/NXR0   NCS1K4-1.2T-K9        0.1   CpuModFw         S   CURRENT  234.10  234.10       NOT REQ
0/3/NXR0   NCS1K4-1.2T-K9        0.1   OptModFw         S   CURRENT    1.38    1.38       NOT REQ
0/Rack     NCS1014               0.1   ADM-CHASSIS          CURRENT    0.21    0.21       NOT REQ
0/Rack     NCS1014               0.1   IoFpga           S   CURRENT    1.10    1.10       NOT REQ
0/Rack     NCS1014               0.1   IoFpgaGolden     BS  CURRENT            1.05       NOT REQ
0/Rack     NCS1014               0.1   SsdIntelSC2KB    S   CURRENT    1.20    1.20        0/Rack

Status—Upgrade status of the firmware. The different states are:
- CURRENT—The firmware version is the latest version.
- NOT READY—The firmware of the FPD is not ready for upgrade.
- NEED UPGD—A newer firmware version is available in the installed image. We recommended that upgrade be performed.
- UPGD PREP—The firmware of the FPD is preparing for upgrade.
- RLOAD REQ—The upgrade is completed, and the card requires a reload.
- UPGD DONE—The firmware upgrade is successful.
- UPGD FAIL—The firmware upgrade has failed.
- UPGD SKIP—The upgrade is skipped because the installed firmware version is higher than the version available in the image.
- Running—Current version of the firmware running on the FPD.

Step 2

show fpd package

Use the show fpd package command to display the FPD image version available with this software release for each hardware component.

Example:

RP/0/RP0/CPU0:ios#show fpd package 

=============================== ================================================
                                        Field Programmable Device Package
                                ================================================
                                               Req     SW      Min Req   Min Req
Card Type            FPD Description           Reload  Ver     SW Ver  Board Ver
=================== ========================== ====== ======= ======== =========
--------------------------------------------------------------------------------
NCS1014-SA           ADM-CHASSIS                NO      0.21      0.21      0.0  
                     IoFpga                     NO      1.10      1.10      0.0  
                     IoFpgaGolden               NO      1.05      1.05      0.0  
                     SsdIntelSC2KB              YES     1.20      1.20      0.0  
--------------------------------------------------------------------------------
NCS1K14-2.4T-K9      CpuModFw                   NO    234.10    234.10      0.0  
--------------------------------------------------------------------------------
NCS1K14-2.4T-L-K9    CpuModFw                   NO    234.10    234.10      0.0  
--------------------------------------------------------------------------------
NCS1K14-CCMD-16-C    CpuModFw                   NO    234.10    234.10      0.0  
                     OptModFw                   NO     15.01     15.01      0.0  
--------------------------------------------------------------------------------
NCS1K14-CCMD-16-L    CpuModFw                   NO    234.10    234.10      0.0  
                     OptModFw                   NO     15.01     15.01      0.0  
--------------------------------------------------------------------------------
NCS1K14-CNTLR-K9     ADM-DB                     NO      2.10      2.10      0.2  
                     ADM-MB                     NO      2.30      2.30      0.2  
                     BIOS                       YES     4.70      4.70      0.0  
                     BIOS-Golden                YES     4.70      0.01      0.0  
                     CpuFpga                    YES     1.09      1.09      0.0  
                     CpuFpgaGolden              YES     1.09      1.09      0.0  
                     SsdIntelS4510              YES    11.32     11.32      0.0  
                     SsdIntelSC2KB              YES     1.20      1.20      0.0  
                     SsdMicron5300              YES     0.01      0.01      0.0  
                     TamFw                      YES     9.04      9.04      0.0  
                     TamFwGolden                YES     9.04      9.04      0.0  
--------------------------------------------------------------------------------
NCS1K14-CTLR-B-K9    ADM-DB                     NO      2.10      2.10      0.2  
                     ADM-MB                     NO      2.30      2.30      0.2  
                     BIOS                       YES     4.70      4.70      0.0  
                     BIOS-Golden                YES     4.70      0.01      0.0  
                     CpuFpga                    YES     1.09      1.09      0.0  
                     CpuFpgaGolden              YES     1.09      1.09      0.0  
                     SsdIntelS4510              YES    11.32     11.32      0.0  
                     SsdIntelSC2KB              YES     1.20      1.20      0.0  
                     SsdMicron5300              YES     0.01      0.01      0.0  
                     TamFw                      YES     9.04      9.04      0.0  
                     TamFwGolden                YES     9.04      9.04      0.0  
--------------------------------------------------------------------------------
NCS1K4-1.2T-K9       CpuModFw                   NO    234.10    234.10      0.0  
                     OptModFw                   NO      1.38      1.38      0.0  
--------------------------------------------------------------------------------
NCS1K4-AC-PSU        PO-PriMCU                  NO      2.04      2.04      0.1  
                     PO-SecMCU                  NO      2.06      2.06      0.1  
--------------------------------------------------------------------------------
NCS1K4-AC-PSU-2      PO-PriMCU                  NO      1.03      1.03      0.1  
                     PO-SecMCU                  NO      1.05      1.05      0.1

What to do next

Upgrade all the FPDs using the upgrade hw-module location all fpd all command in the Cisco IOS XR EXEC mode. After upgrade is completed, the Status column shows RLOAD REQ if the software requires reload.

If Reload is required

If the FPGA location is 0/RP0, use the admin hw-module location 0/RP0 reload command. This command reboots only the CPU. As a result, traffic is not impacted. If the FPGA location is 0/0, use the admin hw-module location all reload command. This command reboots the chassis. As a result, traffic is impacted. After the reload is completed, the new FPGA runs the current version.

If Firmware Upgrade Fails

If firmware upgrade fails, use the show logging command to view the details and upgrade the firmware again using the above commands.

Note

You can upgrade the firmware version of power modules, only when both the power modules are present and powered on.

Verify Alarms

You can view the alarm information using the show alarms command.

Procedure

Displays alarms in brief or detail.

Example:

RP/0/RP0/CPU0:ios#show alarms brief card location 0/RP0/CPU0 active

------------------------------------------------------------------------------------
Active Alarms 
------------------------------------------------------------------------------------
Location        Severity     Group            Set Time                   Description                                                                                                                                                                                                                                                
------------------------------------------------------------------------------------
0/0             Major        Ethernet         11/21/2023 11:11:35 UTC    HundredGigECtrlr0/0/0/2 - Carrier Loss On The LAN                                                                                                                                                                                                          
0/3             Major        Ethernet         11/21/2023 11:11:37 UTC    HundredGigECtrlr0/3/0/2 - Remote Fault                                                                                                                                                                                                                     
0/0             Major        Ethernet         11/21/2023 11:11:38 UTC    HundredGigECtrlr0/0/0/4 - Local Fault                                                                                                                                                                                                                      
0/3             Major        Ethernet         11/21/2023 11:11:38 UTC    HundredGigECtrlr0/3/0/3 - Local Fault                                                                                                                                                                                                                      
0/3             Major        Ethernet         11/21/2023 11:11:38 UTC    HundredGigECtrlr0/3/0/4 - Local Fault                                                                                                                                                                                                                      
0/0             Major        Ethernet         11/21/2023 11:11:38 UTC    HundredGigECtrlr0/0/0/5 - Local Fault                                                                                                                                                                                                                      
0/0             Major        Ethernet         11/21/2023 11:11:38 UTC    HundredGigECtrlr0/0/0/6 - Local Fault                                                                                                                                                                                                                      
0/0             Major        Ethernet         11/21/2023 11:11:38 UTC    HundredGigECtrlr0/0/0/7 - Local Fault                                                                                                                                                                                                                      
0/3             Major        Ethernet         11/21/2023 11:11:39 UTC    HundredGigECtrlr0/3/0/5 - Local Fault                                                                                                                                                                                                                      
0/3             Major        Ethernet         11/21/2023 11:11:39 UTC    HundredGigECtrlr0/3/0/6 - Local Fault                                                                                                                                                                                                                      
0/3             Major        Ethernet         11/21/2023 11:11:38 UTC    HundredGigECtrlr0/3/0/7 - Local Fault                                                                                                                                                                                                                      
0/0             Major        Ethernet         11/21/2023 11:11:43 UTC    HundredGigECtrlr0/0/0/3 - Local Fault                                                                                                                                                                                                                      
0/3             Major        Ethernet         11/21/2023 11:11:57 UTC    HundredGigECtrlr0/3/0/8 - Local Fault                                                                                                                                                                                                                      
0/3             Major        Ethernet         11/21/2023 11:11:57 UTC    HundredGigECtrlr0/3/0/9 - Local Fault                                                                                                                                                                                                                      
0/3             Major        Ethernet         11/21/2023 11:11:59 UTC    HundredGigECtrlr0/3/0/12 - Local Fault                                                                                                                                                                                                                     
0/3             Major        Ethernet         11/21/2023 11:11:59 UTC    HundredGigECtrlr0/3/0/13 - Local Fault                                                                                                                                                                                                                     
0/0             Major        Ethernet         11/21/2023 11:12:03 UTC    HundredGigECtrlr0/0/0/9 - Local Fault                                                                                                                                                                                                                      
0/0             Major        Ethernet         11/21/2023 11:12:04 UTC    HundredGigECtrlr0/0/0/8 - Local Fault                                                                                                                                                                                                                      
0/0             Major        Ethernet         11/21/2023 11:12:04 UTC    HundredGigECtrlr0/0/0/10 - Local Fault                                                                                                                                                                                                                     
0/0             Major        Ethernet         11/21/2023 11:12:04 UTC    HundredGigECtrlr0/0/0/11 - Local Fault                                                                                                                                                                                                                     
0/0             Major        Ethernet         11/21/2023 11:12:04 UTC    HundredGigECtrlr0/0/0/12 - Local Fault                                                                                                                                                                                                                     
0/0             Major        Ethernet         11/21/2023 11:12:04 UTC    HundredGigECtrlr0/0/0/13 - Local Fault                                                                                                                                                                                                                     
0/3             Major        Ethernet         11/21/2023 11:12:04 UTC    HundredGigECtrlr0/3/0/11 - Local Fault                                                                                                                                                                                                                     
0/3             Major        Ethernet         11/21/2023 11:12:05 UTC    HundredGigECtrlr0/3/0/10 - Local Fault

Note

In the maintenance mode, all the alarms are suppressed and the show alarms command will not show the alarms details. Use the show controllers controllertype R/S/I/P command to view the client and trunk alarms.

Verify Context

The show context command displays core dump context information of NCS 1014.

Procedure

show context

When you excecute the show context command in Cisco IOS XR EXEC mode, the output displays the core dump context information of any process on the NCS 1014 as well as up to 10 last instances.

Example:

RP/0/RP0/CPU0:ios#sh context

node: node0_RP0_CPU0
Context number: 1
----------------------------------------------------------------
Core location: 0/RP0/CPU0:/misc/disk1                                                                                                              
Core for pid = 6232 (Terminal_Device)
Core for process: opt_terminal_device_6232.by.11.20231204-170249.node0_RP0_CPU0.877b9.core.gz
Core dump time: 2023-12-04 17:02:50.144240146 +0000

Process:
Core was generated by `opt_terminal_device'.

Build information:
### XR Information

User = deenayak
Host = iox-ucs-061
Workspace = /auto/iox-ucs-061-san1/prod/24.1.1.32I.SIT_IMAGE/ncs1010/ws/
Built on = Fri Nov 17 17:17:31 UTC 2023
Lineup = r241x.lu%EFR-00000453356
XR version = 24.1.1.32I

### Leaba Information


Platform information:
card_product_id: NCS1014
platform: ncs1010

Signal information:
Program terminated with signal 11, Segmentation fault.

Faulting thread: 6232

Registers for Thread 6232
rax:    0x7f2d0d7be000
rbx:    0x0
rcx:    0x0
rdx:    0x7f
rsi:    0x0
rdi:    0x7fff2f3d3420
rbp:    0x0
rsp:    0x7fff2f3d3410
r8:     0x0
r9:     0x7fff2f3d3510
r10:    0xffffffffffffff80
r11:    0x5287
r12:    0x7f
r13:    0x7fff2f3d3420
r14:    0x7f2d0dac4684
r15:    0x7fff2f3d3598
rip:    0x7f2d0d6701ca
eflags: 0x10206
cs:     0x33
ss:     0x2b
ds:     0x0
es:     0x0
fs:     0x0
gs:     0x0


Backtrace for Thread 6232
#0  0x00007f2d0d6701ca in ?? () from /lib64/libc-2.31.so
#1  0x00007f2d0d64b4d5 in snprintf+0x85 from /lib64/libc-2.31.so
#2  0x00007f2d0dadf5cf in ?? () from /opt/cisco/install-iosxr/base/lib/libopenconfig_cmn.so
#3  0x00007f2d0dade7a2 in ?? () from /opt/cisco/install-iosxr/base/lib/libopenconfig_cmn.so
#4  0x00007f2d0dfd6b35 in ?? () from /opt/cisco/install-iosxr/base/lib/libinfra_sysdb_combine_82eb6a4d2fa15d0e.so
#5  0x00007f2d0dfd4b0e in sysdb_process_pending_pulse+0x512 from /opt/cisco/install-iosxr/base/lib/libinfra_sysdb_combine_82eb6a4d2fa15d0e.so
#6  0x00007f2d0e11e3bd in ?? () from /opt/cisco/install-iosxr/base/lib/libinfra_combine_82eb6a4d2fa15d0e.so
#7  0x00007f2d0e12831e in xr_event_dispatch+0x48 from /opt/cisco/install-iosxr/base/lib/libinfra_combine_82eb6a4d2fa15d0e.so
#8  0x00005607924be6a9 in ?? ()
#9  0x00007f2d0d61cd1b in __libc_start_main+0xeb from /lib64/libc-2.31.so
#10 0x00005607924be31a in ?? ()

----------------------------------------------------------------

node: node0_RP0_CPU0
Context number: 2
----------------------------------------------------------------
Core location: 0/RP0/CPU0:/misc/disk1                                                                                                              
Core for pid = 5155 (sh_proc_mem_edm)
Core for process: sh_proc_mem_edm_5155.by.user.20231204-105935.node0_RP0_CPU0.4b884.core.gz
Core Dump time: Mon Dec  4 10:59:35 2023

Process:
Core was generated by: user requested dump of pid 5155

Build information:
### XR Information

User = deenayak
Host = iox-ucs-061
Workspace = /auto/iox-ucs-061-san1/prod/24.1.1.32I.SIT_IMAGE/ncs1010/ws/
Built on = Fri Nov 17 17:17:31 UTC 2023
Lineup = r241x.lu%EFR-00000453356
XR version = 24.1.1.32I

### Leaba Information


Registers for Thread (LWP 5155)
rax:    0xfffffffffffffffc
rbx:    0x5570ec6edd60
rcx:    0x7f0239431cd6
rdx:    0x20
rsi:    0x5570ec6ee060
rdi:    0x1b
rbp:    0x7ffca2a8b690
rsp:    0x7ffca2a8b4e0
r8:     0x0
r9:     0x436
r10:    0xffffffff
r11:    0x293
r12:    0x5570ec6ee020
r13:    0x5570ec6ede70
r14:    0x5570ec6ee060
r15:    0x5570ec6edd60
rip:    0x7f0239431cd6
eflags: 0x293
cs:     0x33
ss:     0x2b
ds:     0x0
es:     0x0
fs:     0x0
gs:     0x0


Backtrace for Thread (LWP 5155)
#0  0x00007f0239431cd6 in ?? () from /lib64/libc-2.31.so
#1  0x00007f0238fefd2a in event_del_nolock_+0x3a from /usr/lib64/libevent-2.1.so.7.0.0
#2  0x00007f0238fe3dbe in ?? () from /usr/lib64/libevent-2.1.so.7.0.0
#3  0x00007f0239799034 in event_block+0x204 from /opt/cisco/install-iosxr/base/lib/libinfra_combine_82eb6a4d2fa15d0e.so
#4  0x00005570ec41fba8 in ?? () from /opt/cisco/install-iosxr/base/bin/sh_proc_mem_edm
#5  0x00007f023935ed1b in ?? () from /lib64/libc-2.31.so
#6  0x00005570ec41f8fa in ?? () from /opt/cisco/install-iosxr/base/bin/sh_proc_mem_edm

----------------------------------------------------------------

node: node0_RP0_CPU0
Context number: 3
----------------------------------------------------------------
Core location: 0/RP0/CPU0:/misc/disk1                                                                                                              
Core for pid = 4316 (sysdb_mc_main)
Core for process: sysdb_mc_4316.by.user.20231203-161922.node0_RP0_CPU0.3f09d.core.gz
Core Dump time: Sun Dec  3 16:19:22 2023

Process:
Core was generated by: user requested dump of pid 4316

Build information:
### XR Information

User = deenayak
Host = iox-ucs-061
Workspace = /auto/iox-ucs-061-san1/prod/24.1.1.32I.SIT_IMAGE/ncs1010/ws/
Built on = Fri Nov 17 17:17:31 UTC 2023
Lineup = r241x.lu%EFR-00000453356
XR version = 24.1.1.32I

### Leaba Information


Registers for Thread (LWP 4316)
rax:    0xfffffffffffffffc
rbx:    0x0
rcx:    0x7f46904eca92
rdx:    0x0
rsi:    0x0
rdi:    0x7ffd281477c0
rbp:    0x7ffd28147a00
rsp:    0x7ffd281476e0
r8:     0x0
r9:     0x0
r10:    0x8
r11:    0x293
r12:    0x1
r13:    0x0
r14:    0x0
r15:    0x7ffd281477c0
rip:    0x7f46904eca92
eflags: 0x293
cs:     0x33
ss:     0x2b
ds:     0x0
es:     0x0
fs:     0x0
gs:     0x0


Backtrace for Thread (LWP 4316)
#0  0x00007f46904eca92 in ?? () from /lib64/libc-2.31.so
#1  0x00005583860ea640 in ?? () from /opt/cisco/install-iosxr/base/sbin/sysdb_mc
#2  0x00005583860bbbd1 in ?? () from /opt/cisco/install-iosxr/base/sbin/sysdb_mc
#3  0x00007f46904d7d1b in ?? () from /lib64/libc-2.31.so
#4  0x00005583860bbada in ?? () from /opt/cisco/install-iosxr/base/sbin/sysdb_mc

----------------------------------------------------------------

node: node0_RP0_CPU0
Context number: 4
----------------------------------------------------------------
Core location: 0/RP0/CPU0:/misc/disk1                                                                                                              
Core for pid = 4212 (sysdb_svr_local)
Core for process: sysdb_svr_local_4212.by.user.20231203-161920.node0_RP0_CPU0.bf2d1.core.gz
Core Dump time: Sun Dec  3 16:19:20 2023

Process:
Core was generated by: user requested dump of pid 4212

Build information:
### XR Information

User = deenayak
Host = iox-ucs-061
Workspace = /auto/iox-ucs-061-san1/prod/24.1.1.32I.SIT_IMAGE/ncs1010/ws/
Built on = Fri Nov 17 17:17:31 UTC 2023
Lineup = r241x.lu%EFR-00000453356
XR version = 24.1.1.32I

### Leaba Information


Registers for Thread (LWP 4212)
rax:    0xfffffffffffffffc
rbx:    0x0
rcx:    0x7f1fcb1c4a92
rdx:    0x0
rsi:    0x0
rdi:    0x7fff60339f50
rbp:    0x7fff6033a200
rsp:    0x7fff60339e80
r8:     0x0
r9:     0x0
r10:    0x8
r11:    0x293
r12:    0x0
r13:    0x0
r14:    0x7fff60339f50
r15:    0x7f1fcb50da9e
rip:    0x7f1fcb1c4a92
eflags: 0x293
cs:     0x33
ss:     0x2b
ds:     0x0
es:     0x0
fs:     0x0
gs:     0x0


Backtrace for Thread (LWP 4212)
#0  0x00007f1fcb1c4a92 in ?? () from /lib64/libc-2.31.so
#1  0x00007f1fcb5af472 in sysdb_svr_main+0xd15 from /opt/cisco/install-iosxr/base/lib/libsysdbsvr_only.so
#2  0x000055e2fd529851 in ?? () from /opt/cisco/install-iosxr/base/sbin/sysdb_svr_local
#3  0x00007f1fcb1afd1b in ?? () from /lib64/libc-2.31.so
#4  0x000055e2fd52975a in ?? () from /opt/cisco/install-iosxr/base/sbin/sysdb_svr_local

----------------------------------------------------------------

Verify Core Files

The dir harddisk:/*core.gz command checks for core files of NCS 1014.

Procedure

dir harddisk:/*core.gz

Example:

RP/0/RP0/CPU0:ios#dir harddisk:/*core.gz
Wed Dec 6 04:54:16.336 UTC

Directory of harddisk:/*core.gz
2476 -rw-r--r--. 1 8120038 Oct 30 15:08 cma_server_41264.by.6.20231030-150817.node0_RP0_CPU0.502a7.core.gz

Bias-Free Language

Results

Chapter: Perform Preliminary Checks

Perform Preliminary Checks

Inventory Support in NCS 1014

Verify Inventory

Procedure

Example:

Verify Status of Hardware Components

Before you begin

Procedure

Example:

Example:

Verify Software Version

Procedure

Example:

Verify Environmental Parameters

Verify Management Interface Status

Procedure

Example:

What to do next

Verify Firmware Version

Before you begin

Procedure

Example:

Example:

What to do next

Verify Alarms

Procedure

Example:

Verify Context

Procedure

Example:

Verify Core Files

Procedure

Example:

Was this Document Helpful?

Contact Cisco