Cisco ONS 15454 and Cisco ONS 15327 TL1 Command Guide, Release 4.0

•ML1000

•EXTSYNCH

•AEP

•FAN

•AIP

•FUDC

• BITS

•HDGE (G1000)

•BP

•MSUDC

•CC

•NBR

•CKT

•NE

•DS1

•NERING

•DS3

•NESYNCH

•DWDM Client

•OCN

•ECN

•STSMON

•ENV

•STSTERM

•EQPT

•VT-MON

•ETHER

•VT-TERM

EQPT

CR/SA

An Equipment Failure alarm indicates that a hardware failure has occurred on the reporting card.

MFGMEM

CR/SA

The manufacturing data memory failure alarm means that the ONS 15454/15327 cannot access the data on the erasable programmable read-only memory (EPROM).

INVMACADR

MJ/NSA

The ONS 15454/15327 media access control layer address (MAC address) is invalid.

MEA

CR/SA

If the Mismatch of Equipment Attributes alarm is reported against the AIP, the fuse in the AIP board blew or is missing. The MEA alarm also occurs when an old AIP board with a 2-Amp fuse is installed in a newer 10 Gbps-compatible or ANSI shelf assembly (15454-SA-ANSI).

MFGMEM

CR/SA

The manufacturing data memory failure alarm means that the ONS 15454/15327 cannot access the data on the erasable programmable read-only memory (EPROM).

LOF

MJ/SA

A port on the TCC/MIC BITS input detects a loss of frame (LOF) on the incoming BITS timing reference signal.

LOS

MJ/SA

The TCC/MIC card has a loss of signal (LOS) condition from the BITS timing source.

SSM-FAIL

MN/NSA

Synchronization status messaging failed.

MEA

CR/SA

The Mismatch of Equipment and Attributes (MEA) alarm for the backplane means that the revision of the backplane is incompatible with XC10G equipment.

MFGMEM

CR/SA

The Manufacturing Data Memory Failure (MFGMEM) alarm means that the ONS 15454/15327 cannot access the data on the erasable programmable read-only memory (EPROM).

CKTDOWN

CR/SA

The Unified Control Plane (UCP) Circuit Down alarm applies to logical circuits created within the UCP between devices.

LMP-HELLODOWN

MN/NSA

The Link Management Protocol (LMP) Hello Down alarm means that Hello protocol, which monitors unified control plane (UCP) control channel status, is not available for link management.

LMP-NDFAIL

MN/NSA

The LMP Neighbor Detection Fail alarm means that neighbor detection within the UCP has failed.

CKTDOWN

CR/SA

The Unified Control Plane (UCP) Circuit Down alarm applies to logical circuits created within the UCP between devices and It occurs when the there is signaling failure across a UCP interface..

LOF

MJ/SA

The receiving ONS 15454/15327 has lost frame delineation in the incoming data.

LOS

MJ/SA

A loss of signal (LOS) at the card for either a DS-3 port or a DS-1 port.

RCVR-MISS

MJ/SA

The facility termination equipment detects an incorrect amount of impedance on its backplane connector.

TRMT

MJ/SA

There is a transmit failure on the DS1-14 card due to an internal hardware failure.

TRMT-MISS

MJ/SA

The facility termination equipment detects an incorrect amount of impedance on its backplane connector.

LOF

CR/SA

The receiving ONS 1545415327 has lost frame delineation in the incoming data.

LOS

CR/SA

This LOS for either a DS-3 port or a DS1-14 port occurs when the port on the card is in service but no signal is being received.

AUTOLSROFF

CR/SA

The Auto Laser Shutdown alarm occurs when the OC-192 card temperature exceeds 194° F (90 ° C).

CARLOSS (ML-Series)

MJ/SA

The Ethernet port has lost its link and is not receiving a valid signal.

EOC

MJ/NSA

The SONET Data Communications Channel (DCC) Termination Failure alarm occurs when the ONS 15454 loses its data communications channel.

HI-LASERBIAS

MN/NSA

The Equipment High Transmit Laser Bias Current alarm is raised against the TXP and MXP card laser performance. The alarm indicates that the card laser has reached the maximum laser bias tolerance.

HI-LASERTEMP

MN/NSA

The Equipment High Laser Optical Transceiver Temperature alarm applies to the TXP and MXP cards. This alarm occurs when the internally measured transceiver temperature exceeds the card default level.

HI-RXPOWER

MN/NSA

The Equipment High Receive Power alarm is an indicator for TXP card and MXP card received optical signal power. This alarm occurs when the measured optical power of the received signal exceeds the threshold.

HI-TXPOWER

MN/NSA

The Equipment High Transmit Power alarm is an indicator for TXP card and MXP card transmitted optical signal power. This alarm occurs when the measured optical power of the transmitted signal exceeds the threshold.

LOF (OC-N)

CR/SA

The LOF alarm occurs when a port on the reporting OC-N card has an LOF condition. LOF indicates that the receiving ONS 15454 has lost frame delineation in the incoming data.

LO-LASERBIAS

MN/NSA

The Equipment Low Transmit Laser Bias Current alarm is raised against the TXP and MXP card laser performance. The alarm indicates that the card laser has reached the minimum laser bias tolerance.

LO-LASERTEMP

MN/NSA

The Equipment Low Laser Optical Transceiver Temperature alarm applies to the TXP and MXP cards. This alarm occurs when the internally measured transceiver temperature falls under the card default level.

LO-RXPOWER

MN/NSA

The Equipment Low Receive Power alarm is an indicator for TXP card and MXP card received optical signal power. This alarm occurs when the measured optical power of the received signal falls under the threshold.

LOS (OC-N)

CR/SA

An OC-N LOS alarm occurs when a SONET receiver detects an all-zero pattern for 10 microseconds or longer.

LO-TXPOWER

MN/NSA

The Equipment Low Transmit Power alarm is an indicator for TXP card and MXP card transmitted optical signal power. This alarm occurs when the measured optical power of the transmitted signal falls under the threshold.

PORT-CODE-MISM

MJ/MSA

The Pluggable Port Security Code Mismatch alarm refers to ML-series Ethernet cards, MXP and TXP cards and occurs when the SFP connector that is plugged into the card is not supported by Cisco.

PORT-COMM-FAIL

MJ/SA

The Port Communication Failure alarm applies to TXP and MXP card SFPs and occurs when the card cannot communicate with the SFP.

PORT-MISMATCH

MJ/NSA

The Pluggable Port Mismatch alarm applies to ML-series Ethernet card small form pluggable (SFP) connectors. The alarm indicates that the provisioned payload for the connector does not match the SFP configuration.

PORT-MISSING

MJ/NSA

The Pluggable Port Missing alarm applies to ML-series Ethernet card small form pluggable (SFP) connectors. The alarm indicates that the connector is not plugged into the card port.

SQUELCHED

MJ/SA

The DWDM Client Signal Squelched alarm is raised by an MXP or TXP card when G.709 monitoring is enabled and the card is operating in transparent mode.

SSM-FAIL

MN/NSA

The SSM Failed alarm occurs when the synchronization status messaging received by the ONS 15454 fails.

TIM-P

CR/SA
MN/NSA

CR/SA for STSTERM
MN/NSA for STSMON
The TIM Path alarm occurs when the expected path trace string does not match the received path trace string. Path Trace Mode must be set to manual or auto for the TIM-P alarm to occur.

AUTOLSROFF

CR/SA

The Auto Laser Shutdown alarm occurs when the OC-192 card temperature exceeds 194° F (90° C).

CARLOSS (ML-Series)

MJ/SA

The Ethernet port has lost its link and is not receiving a valid signal.

DSP-COMM-FAIL

MJ/SA

The DSP Communication Failure alarm indicates that there is a communications failure between an MXP or TXP card microprocessor and the on-board DSP chip that controls the trunk (DWDM) port.

DSP-FAIL

MJ/SA

The DSP Failure alarm indicates that a DSP-COMM-FAIL has persisted for an extended period on an MXP or TXP card and that the card is faulty.

EOC

MJ/NSA

The SONET Data Communications Channel (DCC) Termination Failure alarm occurs when the ONS 15454 loses its data communications channel.

GCC-EOC

MJ/NSA

The GCC Embedded Operation Channel Failure alarm applies to the OTN communication channel for TXP and MXP cards. It is raised when the channel cannot operate.

HI-LASERBIAS

MN/NSA

The Equipment High Transmit Laser Bias Current alarm is raised against the TXP and MXP card laser performance. The alarm indicates that the card laser has reached the maximum laser bias tolerance.

HI-LASERTEMP

MN/NSA

The Equipment High Laser Optical Transceiver Temperature alarm applies to the TXP and MXP cards. This alarm occurs when the internally measured transceiver temperature exceeds the card default level.

HI-RXPOWER

MN/NSA

The Equipment High Receive Power alarm is an indicator for TXP card and MXP card received optical signal power. This alarm occurs when the measured optical power of the received signal exceeds the threshold.

HI-RXTEMP

MN/NSA

The Equipment High Receive temperature alarm refers to the temperature of the receiver port on the TXP and MXP cards.

HI-TXPOWER

MN/NSA

The Equipment High Transmit Power alarm is an indicator for TXP card and MXP card transmitted optical signal power. This alarm occurs when the measured optical power of the transmitted signal exceeds the threshold.

LOF (OC-N)

CR/SA

The receiving ONS 15454/15327 has lost frame delineation in the incoming data.

LO-LASERBIAS

MN/NSA

The Equipment Low Transmit Laser Bias Current alarm is raised against the TXP and MXP card laser performance. The alarm indicates that the card laser has reached the minimum laser bias tolerance.

LO-LASERTEMP

MN/NSA

The Equipment Low Laser Optical Transceiver Temperature alarm applies to the TXP and MXP cards. This alarm occurs when the internally measured transceiver temperature falls under the card default level.

LOM

MN/NSA

The Loss of Multiframe alarm applies to MXP and TXP cards when the MFAS overhead field is errored for more than five frames and persists for more than three milliseconds.

LO-RXPOWER

MN/NSA

The Equipment Low Receive Power alarm is an indicator for TXP card and MXP card received optical signal power. This alarm occurs when the measured optical power of the received signal falls under the threshold.

LOS (OC-N)

CR/SA

An OC-N LOS alarm occurs when a SONET receiver detects an all-zero pattern for 10 microseconds or longer.

LO-TXPOWER

MN/NSA

The Equipment Low Transmit Power alarm is an indicator for TXP card and MXP card transmitted optical signal power. This alarm occurs when the measured optical power of the transmitted signal falls under the threshold.

OTUK-IAE

MJ/SA

The OTUK Incoming Alignment Error (IAE) alarm applies to TXP cards and MXP cards when G.709 monitoring is enabled for the cards. OTUK-IAE refers to a single bit that allows the input port to notify the output port that the incoming signal has an alignment error.

OTUK-LOF

CR/SA

The OTUK LOF alarm applies to TXP cards and MXP cards when G.709 monitoring is enabled for the cards. The alarm indicates that the card has lost frame delineation on the input data. Loss of frame occurs when the optical transport unit overhead frame alignment (FAS) area is errored for more than five frames and that the error persists more than three milliseconds.

OTUK-TIM

MN/NSA

The OTUK TIM alarm applies to TXP cards and MXP cards when G.709 monitoring is enabled and section trace mode is set to manual. The alarm indicates that the expected TT1 string does not match the received TTI string in the optical transport unit overhead of the digital wrapper.

PTIM

MN/NSA

The Payload TIM alarm applies to TXP cards and MXP cards when G.709 is enabled for the cards.

SECURITYCODE

MJ/NSA

The Pluggable Port Security Code Mismatch alarm refers to the ML-series Ethernet cards. I means that the SFP connector plugged into the ML-series Ethernet card is not supported by Cisco.

SQUELCHED

MJ/SA

The DWDM Client Signal Squelched alarm is raised by an MXP or TXP card when G.709 monitoring is enabled and the card is operating in transparent mode.

SSM-FAIL

MN/NSA

The SSM Failed alarm occurs when the synchronization status messaging received by the ONS 15454 fails.

TIM-P

CR/SA
MN/NSA

CR/SA for STSTERM
MN/NSA for STSMON
The TIM Path alarm occurs when the expected path trace string does not match the received path trace string. Path Trace Mode must be set to manual or auto for the TIM-P alarm to occur.

WVL-MISMATCH

MJ/SA

The Equipment Wavelength Mismatch alarm applies to the TXP and MXP cards. It occurs when you provision the card in CTC with a wavelength that the card does not support.

LOF (EC1-12)

CR/SA

The receiving ONS 15454 has lost frame delineation in the incoming data.

LOS (EC1-12)

CR/SA

A port on the reporting EC-1 card has a loss of signal condition. A SONET receiver detects an all-zero pattern for 10 microseconds or longer.

EXT

MN/NSA

A Failure Detected External to the NE alarm occurs because an environmental alarm is present, for example, a door is open or flooding has occurred.

AUTORESET

MN/NSA

The Automatic System Reset alarm occurs when you change an IP address or perform any other operation that causes an automatic card-level reboot.

BKUPMEMP

CR/NSA

A problem with the TCC/XTC card's flash memory.

CARLOSS

MJ/SA

A Carrier Loss on the LAN Equipment alarm occurs when the ONS 15454 and the workstation hosting CTC do not have a TCP/IP connection.

COMIOXC

CR/SA

The I/O Slot To Cross-Connect (XCON) Communication Failure alarm is caused by the cross-connect card. It occurs when there is a communication failure for a particular I/O slot.

CONTBUS-A

MJ/NSA

The TCC/XTC card in Slot 7/Slot 5 has lost communication with a traffic card.

CONTBUS-A-18

MJ/NSA

The main processor on the TCC/XTC card in Slot 7/Slot 5 has lost communication with the coprocessor on the second TCC/XTC card in Slot 11/Slot 6.

CONTBUS-B

MJ/NSA

The TCC/XTC card in Slot 11/Slot 6 has lost communication with a traffic card.

CONTBUS-B-18

MJ/NSA

The main processor on the TCC/XTC card in Slot 11/Slot 6 has lost communication with the coprocessor on the TCC/XTC card in Slot 7/Slot 5.

CTNEQPT-PBPROT

CR/SA

A failure of the main payload between the protect cross-connect (XC/XCVT/XC10G) card in Slot 10, or the protect XTC card, and the reporting traffic card.

CTNEQPT-PBWORK

CR/SA

A failure of the main payload bus between the active cross-connect (XC/XCVT/XC10G) card in Slot 8, or the active XTC card, and the reporting traffic card.

ERROR-CONFIG

MN/NSA

The Error in Startup Configuration alarm applies to the ML-series Ethernet cards. These cards process startup configuration files line by line. If one or more lines cannot be executed, the error causes the ERROR-CONFIG alarm.

EQPT

CR/SA

A hardware failure occurred on the reporting card.

EXCCOL

MN/NSA

There are too many collisions are occurring between data packets on the network management LAN, and communications between the ONS 15454/15327 and CTC may be affected.

HITEMP

CR/SA
MN/NSA

CR/SA for NE.
MN/NSA for EQPT.
The High Temperature alarm occurs when the temperature of the ONS 15454 is above 122° F (50° C).

IMPROPRMVL

CR/SA

A card was physically removed from its slot before the card was deleted from CTC.

MEA

CR/SA

The MEA alarm for equipment is reported against a card slot when the physical card inserted into a slot does not match the card type that is provisioned for that slot in CTC.

MEM-GONE

MJ/NSA

Data generated by software operations exceeds the memory capacity of the TCC/XTC card.

MEM-LOW

MN/NSA

Data generated by software operations is close to exceeding the memory capacity of the TCC/XTC card.

NO-CONFIG

MN/NSA

The No Startup Configuration alarm applies to ML-series Ethernet cards and occurs when you pre-provision a high-speed slot for the card without inserting the card first, or when you insert a card without pre-provisioning.

PEER-
NORESPONSE

MJ/NSA

The switch agent raises a Peer Card Not Responding alarm if either traffic card in a protection group does not receive a response to the peer status request message

PROTNA

MN/NSA

The Protection Unit Not Available is raised by an out-of-service protection when a TCC/XTC or cross-connect card or port that is provisioned as part of a protection group is not available.

PWR-REDUN

MN/NSA

The Redundant Power Capability Lost alarm applies to cards (such as the TCC2 and newer optical cards) that have two built-in fuses. The alarm indicates that one of the fuses has blown, and must be serviced.

SFTWDOWN

MN/NSA

A Software Download in progress alarm occurs when the TCC/XTC is downloading or transferring software.

SWMTXMOD

CR/SA

The Switching Matrix Module Failure alarm occurs on the cross-connect card or a traffic card. If the alarm reports against a traffic card, it means that the logic component on the cross-connect card is out of frame (OOF) with the logic component on the reporting traffic card.

CARLOSS (E-Series)

MJ/SA

A Carrier Loss on the LAN E-Series Ethernet Card alarm is the data equivalent of an LOS (OC-N). The Ethernet card has lost its link and is not receiving a valid signal.

CARLOSS (G-Series)

MJ/SA

A Carrier Loss on the LAN G-Series Ethernet Card alarm is the data equivalent of an LOS (OC-N). The Ethernet card has lost its link and is not receiving a valid signal.

SYNCPRI

MN/NSA

A loss of the primary timing source (reference 1).

SYNCSEC

MN/NSA

A loss of the secondary timing source (reference 2).

SYNCTHIRD

MN/NSA

A loss of the third timing source (reference 3).

EQPT-MISS

CR/SA

Indicates the replaceable fan-tray assembly unit is missing or not fully inserted.

FAN

CR/SA

A problem with the fan-tray assembly.

FANDEGRADE

MJ/NSA

The Partial Fan Failure alarm is raised if fan speed for one of the fans in the fan-tray assembly falls below 500 RPM when read by a tachometry counter.

MEA

CR/SA

The MEA alarm is reported against the fan tray when a newer fan-tray assembly (15454-FTA3) with a 5 Amp fuse is used with an older shelf assembly or when an older fan tray with a 2 Amp fuse is used with a newer 10 Gbps compatible or ANSI shelf assembly (15454-SA-ANSI) that contains cards introduced in Release 3.1 or later.

MFGMEM

CR/SA

The manufacturing data memory failure alarm occurs if the ONS 15454 cannot access the data in the erasable programmable read-only memory (EEPROM).

LOS

CR/SA

An OC-N LOS alarm occurs when a SONET receiver detects an all-zero pattern for 10 microseconds or longer. An LOS means the upstream transmitter has failed.

CARLOSS

MJ/SA

A carrier loss on the LAN G-series card is the data equivalent of an LOS (OC-N) alarm. The Ethernet card has lost its link and is not receiving a valid signal.

TPTFAIL

MJ/SA

Indicates a break in the end-to-end Ethernet link integrity feature of the G1000-4 cards. This alarm indicates a far-end condition and not a problem with the port reporting TPTFAIL.

CARLOSS

MJ/SA

The Ethernet port has lost its link and is not receiving a valid signal.

TPTFAIL

MJ/SA

The TPT Layer Failure alarm for the ML-series Ethernet cards indicates a break in the end-to-end POS link integrity feature of the ML-series POS cards.

LOS

CR/SA

An OC-N LOS alarm occurs when a SONET receiver detects an all-zero pattern for 10 microseconds or longer. An LOS means the upstream transmitter has failed.

RSVP-HELLODOWN

MN/NSA

The Resource Reservation Protocol (RSVP) Hello Down alarm means that Hello protocol, which monitors UCP control channel status, is not available for reserving resources.

DATAFLT

MN/NSA

The TCC/XTC exceeds its flash memory.

DBOSYNC

MJ/NSA

The standby TCC/XTC "To be Active" database does not synchronize with the "Active" database on the active TCC/XTC.

EHIBATVG-A

MN/NSA

The voltage level on battery lead A exceeds -56.7 Vdc. (ONS 15454)

EHIBATVG-B

MN/NSA

The voltage level on battery lead B exceeds -56.7 Vdc. (ONS 15454)

ELWBATVG-A

MN/NSA

The voltage on battery feed A is extremely low or has been lost, and power redundancy is no longer guaranteed. (ONS 15454)

ELWBATVG-B

MN/NSA

The voltage on battery feed B is extremely low or has been lost, and power redundancy is no longer guaranteed. (ONS 15454)

HITEMP

CR/SA
MN/NSA

CR/SA for NE
MN/NSA for EQPT

The temperature of the ONS 15454/ONS 15327 is above 122° F (50° C).

PRC-DUPID

MJ/SA

Two identical node IDs exist in the same ring.

PWR-A

MJ/SA

This alarm applies to the NE shelf. It occurs when there is no power supplied to the main power connector. (ONS 15454)

PWR-B

MJ/SA

This alarm applies to the NE rack. It occurs when there is no power supplied to the backup power connector. (ONS 15454)

SNTP-HOST

MN/NSA

The SNTP (Simple Network Timing Protocol) Host Failure alarm indicates that an ONS node serving as an IP proxy for the other ONS nodes in the ring is not forwarding SNTP information to the other ONS nodes in the network.

SYSBOOT

MJ/SA

New software is booting on the TCC/XTC card.

BLSROSYNC

MJ/SA

The BLSR Out Of Sync alarm occurs when a node on a working ring loses its DCC connection because all transmit and receive fiber is removed, and you attempt to add or delete a circuit.

PRC-DUPID

MJ/SA

The Procedural Error Duplicate Node ID alarm indicates that two identical node IDs exist in the same ring.

RING-MISMATCH

MJ/SA

A Procedural Error Mismatch Ring alarm occurs when the ring ID of the ONS node that is reporting the alarm does not match the ring ID of another ONS node in the BLSR.

FRNGSYNC

MJ/SA

The reporting ONS node is in free run synchronization mode.

FSTSYNC

MN/NSA

A Fast Start Synchronization alarm occurs when the ONS node is choosing a new timing reference.

HLDOVRSYNC

MJ/SA

A loss of primary/secondary timing reference.

SYNCPRI

MN/NSA

A loss of the primary timing source (reference 1).

SYNCSEC

MN/NSA

A loss of the secondary timing source (reference 2).

SYNCTHIRD

MN/NSA

A loss of the third timing source (reference 3).

APSB

MN/NSA

The line terminating equipment detects protection switching byte failure in the incoming automatic protection switching (APS) signal.

APSCDFLTK

MN/NSA

A BLSR is not properly configured.

APSC-IMP

MN/NSA

Invalid K bytes.

APSCINCON

MN/SA

The SONET overhead contains K1/K2 APS bytes that notify receiving equipment, such as the ONS 15454/ONS 15327, to switch the SONET signal from a working to a protect path.

APSCM

MJ/SA

The ONS 15454/ONS 15327 expects a working channel but receives a protection channel.

APSCNMIS

MJ/SA

The source node ID contained in the K2 byte of the APS channel being received is not present in the ring map.

APSMM

MN/NSA

There is a mismatch of the protection switching schemes at the two ends of the span.

AUTOLSROFF

CR/SA

The OC-192 card temperature exceeds 194° F (90 ° C). (ONS 15454)

EOC

MJ/NSA

The ONS 15454/ONS 15327 has lost its data communications channel (DCC).

E-W-MISMATCH

MJ/SA

Nodes in a ring have an east slot/port misconnected to another east slot/port or a west slot/port misconnected to another west slot/port.

EXTRA-TRAF-
PREEMPT

MN/NSA

An Extra Traffic Preempted alarm occurs on OC-N cards in two-fiber and four-fiber BLSRs because low-priority traffic directed to the protect system has been preempted by a working system protection switch.

FEPRLF

MN/NSA

an APS switching channel SF occurs on the protect card coming into the node.

LASEREOL

MN/NSA

The Laser Approaching End of Life alarm applies to TXP and MXP cards and occurs when the laser in the card will need to be replaced.

LOF

CR/SA

A port on the reporting OC-N card has an LOF condition.

LOS

CR/SA

A SONET receiver detects an all-zero pattern for 10 microseconds or longer.

SSM-FAIL

MN/NSA

Synchronization status messaging received by the ONS 15454/ONS 15327 fails.

LOP-P

CR/SA

A loss of pointer (LOP) condition at the path level.

PLM-P

CR/SA

A signal label mismatch failure (SLMF).

TIM-P

MN/SA

The expected path trace string does not match the received path trace string.

UNEQ-P

CR/SA

The path does not have a valid sender.

LOP-P

CR/SA

A loss of pointer (LOP) condition at the path level.

PLM-P

CR/SA

A signal label mismatch failure (SLMF).

TIM-P

MN/SA

The expected path trace string does not match the received path trace string. Path trace mode can be set to auto or manual for this alarm to occur.

UNEQ-P

CR/SA

The path does not have a valid sender.

AUTOSW-LOP

MN/SA

Automatic path protection configuration protection switching occurred because of an LOP alarm.

AUTOSW-
UNEQ

MN/SA

Automatic path protection configuration protection switching occurred because of an UNEQ alarm.

LOP-V

MJ/SA

A loss of pointer at the VT level.

UNEQ-V

MJ/SA

The node is receiving SONET path overhead with bits 5, 6 and 7 of the V5 overhead byte all set to zeroes.

LOP-V

MJ/SA

A loss of pointer at the VT level.

PLM-V

MN/SA

The content of the V5 byte in the SONET overhead is inconsistent or invalid.

UNEQ-V

MJ/SA

The node is receiving SONET path overhead with bits 5, 6 and 7 of the V5 overhead byte all set to zeroes.

ENEQ

Control Not Provisioned

Environmental Control Interface Not Found

Equipment Not Found

Equipment Not Present

Equipment Not Provisioned

Internal Communication Error

Sensor Interface Not Found

IBEX

Invalid AID Block. Extra Datablock

Invalid Payload Block. Extra Datablock

ICNV

Cannot Set DCC When G709 Is Enabled

Equipment Does Not Match Request

Equipment In Use

Invalid Command

Operation Not Supported By This Card

Performance Monitoring Type Not Supported

IDMS

Loopback Type Missing

Missing Internal Data

IDNC

Invalid Data

Invalid PST Value

Invalid SST Value

IDNC (continued)

Primary Source Cannot Be INTERNAL When Secondary Source Is Not INTERNAL

Primary Source Cannot Be INTERNAL When Third Source Is Not INTERNAL

Secondary Source Cannot Be INTERNAL When Third Source Is Not INTERNAL

IDNV

2F-BLSR Architecture Does Not Permit Manual/Forced Span Switching

AUTO Trace Mode Not Allowed

At least an XC10G XC card is needed for this equipment type

Cannot Change Protection Type

Command Not Valid On Protect Card

DCC Not Supported In Transparent Term Mode

Equipment Does Not Support Payload Type

Equipment Does Not Support Regeneration Group

Facility Loopback Not Supported

Frame Format Contains Invalid Data

Frame Format Not Supported On Equipment

GCC Not Supported On CLNT Port

Incompatible Equipment Type

Incompatible Equipment Type For Protection

Incompatible Protect Slot For Protection

Interval Out Of Range

Invalid AID For PCA Cross-Connection

Invalid Data For 2F-BLSR

Invalid Drop Path

Invalid Equipment Type

Invalid Ethernet Frame Size

Invalid Holdoff Timer Value

Invalid Log Name

Invalid MONLEV Value

Invalid MONTYPE Value

Invalid Mac Address

Invalid PM Interval

Invalid Peer Id

Invalid Protid

Invalid Reference

Invalid Report Interval

IDNV (continued)

Invalid Start Time

Invalid Switch Type For BLSR

Invalid TAP Number

Invalid Time Offset

Invalid Trace Level

J0 Section Trace Not Supported In Transparent Term Mode

Keyword All Not Allowed

Line Code Not Supported

Multiple AIDs Not Allowed

Multiple Protection Group Card Slot Identifiers Not Allowed

Multiple References Not Allowed

Null Userid Or Range In Userid List Not Allowed

Number Of Reports Is Negative

Parameter Not Supported By Payload Type

Parameter Not Supported On Client DWDM Port

Payload Type Does Not Support DCC

Protect Card Does Not Support Protection Type

Protect Slot Not Provisioned

Protection Group Card Slot Identifier Field Required

Protection Group Does Not Exist

Protection Group Name Exceeds Maximum Length

Ring Lockout BLSR Switching Is Not Supported

Switch Type Is Not Allowed On 1+1

Term Mode Does Not Support Synchronization/Timing Parameters

Threshold Value Out Of Range

Trace Level Not Supported By Client Port

Trace Level Required

Trace Not Supported In Transparent Term Mode

Transponder Does Not Support Synchronization/Timing Parameters

VOA Out Of Range

IDRG

Difference Value Range Error

Invalid PJMON Value

Invalid Threshold Value

IIAC

AID Does Not Match with Requested BLSR Path Type

ALL, Ranging and Grouping Are Not Supported

CCT=1WAY Not Allowed When G1000 Or ML Series Ports Are Used

Cannot Make Changes To Protect Card

Cross-Connection Cannot Overlap PCA Boundary

Equipment Can Not Be Provisioned On Low Speed Slot

Equipment Does Not Match Request

Expected Trace Not Supported On This Card Type

Expected Trace String Exceeds Maximum Length (62)

Incoming Trace Not Supported On This Card Type

Incorrect Card Type

Input, Invalid Access

Invalid AID

Invalid DS1 AID

Invalid G1000 Facility Port

Invalid Month Or Day

Invalid NodeId

Invalid Operation On Drop AID

Invalid PJMON Value

Invalid Protect AID

Invalid Protect AID Or Working AID

Invalid Reference

Invalid RingId

Invalid Source/Destination AID Count For Cross-Connection Type

Invalid TAP

Invalid Time

Invalid Year

J1 Trace Not Supported On This Card

List AID Not Allowed For ALL AID

List Or All AID Not Supported

Multiple AIDs Not Supported

Multiple Destination AID Exceeds Limit

Multiple Destinations Not Supported By Cross-Connection

Multiple Source AID Exceeds Limit

Multiple TAP AIDs Not Supported

Not Allowed On 1+1 Protect Line

IIAC (continued)

Not Allowed On BLSR Protect Line

Optional AIDs Are Not Supported

RingId Does Not Match with AID Number

Trace Mode Not Supported On This Card Type

Trace Not Supported On This Card Type

Trace String Exceeds Maximum Length (62)

UPSR Cross-Connections Not Allowed When G1000 Or ML-Series Ports Are Used

IICM

Input, Invalid MOD1

Input, Invalid VERB

IICT

Invalid Correlation Tag

IIDT

2F-BLSR Does Not Support SRVRTV/SRVTM/EASTPROT/WESTPROT Parameters

Cannot Activate To Older Software

Cannot Add And Remove Drops Together

Cannot Revert From R2 To R1

Cannot Revert To Newer Software

Command Already In Progress

DEST Incompatible With RFR Type

DEST Incompatible With SWDL Type

DEST Required For RFBU Type

Duplicate BLSR Working/Protect Facilities

Duplicate Performance Monitoring Schedule

File Name Missing in FTP URL

Flash Manager Not Active

Hostname Missing In FTP URL

IOS Config File Too Big

Invalid BLSR Mode

Invalid BLSR Protect Facility

Invalid BLSR Working Facility

Invalid Data Parameter

Invalid Port In FTP URL

Invalid Revertive Time

Invalid Software Switch Type

Invalid State Value

Mandatory FTP URL Not Provided

Maximum Performance Monitoring Schedule Limit Reached

IIDT (continued)

Memory Out Of Range

Missing/Invalid Destination

Missing/Invalid Source

Non-IP Hostname In FTP URL

Null Outputs In FTP URL Parsing

Only NORM CMD_MODE Is Supported

Only OOS PST Is Supported

Only Port 21 Is Supported

Only SWDL Is Supported For The xfertype Argument

Password Missing In FTP URL

Performance Monitoring Schedule Does Not Exist

Port Missing In FTP URL

SRC Incompatible With RFBU Type

SRC Required For RFR Type

SRC Required For SWDL Type

SWDL Incompatible With RFILE-PKG Aid

Software Activate/Revert Failed

Software Not Available For Switch

Unknown Error Processing FTP URL.

Username Missing In FTP URL

ftp:// Missing In FTP URL

IIFM

Invalid AID Block. Invalid Data Format.

Invalid Payload Block. Invalid Data Format.

IISP

Input, Garbage

IITA

Input, Invalid Target Identifier

INUP

General Block Unsupported

IPEX

Invalid Payload Block. Extra Parameters.

Invalid Payload Block. Extra Parameters.

IPMS

Invalid AID Block. Missing Mandatory Field.

Invalid Payload Block. Missing Mandatory Field.

IPNC

Cannot Change Existing Protection Type

Description Cannot Have More Than 64 Characters

Invalid Flow Control Value

Invalid Maximum Frame Size

Invalid Parameter

Parameters Are Not Consistent

IPNC (continued)

Parameters Not Compatible

IPNV

Cannot Set Expected Path Trace For Source Path

Cannot Set Expected Path Trace In Auto Mode

Cannot Set Outgoing Path Trace For Drop Path

Cross-Connection Does Not Have UPSR Path Selector

Exercise Is Not Allowed On Protected Facility

Far End Performance Monitoring Values Not Supported

Holdoff Timer Not Supported For Non-DRI Cross-Connections

INT Not Valid For BITS-OUT

Internal-Ip Lookup Failed

Internal-Network Nodes Lookup Failed

Invalid Clock Source

Invalid Default Router Address

Invalid IIOP Port number

Invalid IP Address

Invalid IP Configuration Parameter

Invalid IP Mask

Invalid Parameter

Invalid Payload Block. Empty Parameter.

Invalid SNTP Host Address

Invalid Switch Command For Synchronization

Invalid Switch Type

New Source Must Be Specified

Node Name Exceeds Maximum Length (62)

PM Not Supported

Primary Reference Incompatible With Timing Mode

Protection Type Does Not Support Reversion Mode

Reference Type Not Supported

SPNWTR Parameter Not Supported

Secondary Reference Incompatible With Timing Mode

Synchronization Source Already Defined For The Slot

TMGREF Parameter Not Supported

Third Reference Incompatible With Timing Mode

Time Period Not Applicable

Timing Mode Not Compatible

PICC

AID Required

Invalid User Access Privilege Value

Invalid User Identifier - Must Conform To TL1 Rules

Invalid User Password - Must Conform To TL1 Rules

New Password Same As Old Password

Unknown CORBA Exception (Internal Error)

Unknown User

User Access Privilege Required

User Already Exists

User Identifier Exceeds Maximum Length Allowed

User Not Authorized

User Password Required

PIMA

Memory Out Of Range

PIUC

Cannot Delete The Logged In User

User Currently Logged Into Another Session

User Is Not Superuser

User Not Allowed To Change User Access Privilege

User Not Allowed To Change User Password

User Not Allowed To Lock/Unlock Self

RALB

Requested DCC In Use

RRNG

Invalid Slot Number

Invalid Slot Number For Sdh Electrical Cards

RTBY

Connection In Service

TAP Already In Use

TAP Number In Use

RTEN

Cannot Access VT

Cannot Change Access Mode

Cannot Set Access Mode

Invalid Access Mode

Invalid STS TAP Number

Invalid TAP AID

Invalid TAP Mode

Invalid TAP Number

Invalid VT TAP Number

Requested TAP Does Not Exist

TAP Not Found

SAAL

Already Allowed

SAAS

Equipment Already Provisioned

SADC

TAP Not Connected

SADS

Loopback Applied On Cross-connection

SAIN

Already Inhibited

SAIS

Port Already In Service

SAMS

Already In Clear Maintenance State

Already In Force Maintenance State

Already In Lockout Maintenance State

Already In Manual Maintenance State

SAOP

Control Already Operated

Control Already Released

Control Operated In Mntry

SAOS

Port Already In OOS-AINS

Port Already In OOS-MT

Port Already Out Of Service

SCAT

STS Is Already Connected

Test Access Busy

VT Is Already Connected

SDBE

AID Parser Failed

Cannot Access Conditions

Cannot Access Controls

Cannot Access Date/Time

Cannot Access Defaults Description

Cannot Access Environmental Settings

Cannot Access Equipment

Cannot Access Facility

Cannot Access IP Configuration

Cannot Access Interface

Cannot Access Node ID

Cannot Access Object

Cannot Access Orderwire

Cannot Access Protection Group

Cannot Access Protection State

Cannot Access SNTP Host

Cannot Access STS

SDBE (continued)

Cannot Access Software Version

Cannot Access Synchronization Configuration

Cannot Access Timezone

Cannot Access Trace Information

Cannot Access VT

Cannot Access VT Performance Monitoring Parameters

Cannot Create 1+1 Protection Group

Cannot Edit STS

Cannot Get Line Information

Cannot Get Synchronization Configuration

Cannot Set Date

Cannot Set Date When Using SNTP

Cannot Set IP Configuration

Cannot Set Node Name

Cannot Set Pointer Justification Monitoring Parameter (PJMON)

Cannot Set SNTP Host Configuration

Cannot Set Timezone

Cannot Switch To E2 Byte With Express Orderwire IS

Card Type Not Supported

Delete Protection Group Failed

Equipment Not Found

Facility Does Not Exist

Facility Does Not Match Request

Facility Does Not Support Mac Address

Facility Is Not Provisioned

File Transfer In Progress

IOS Config Update In Progress

Incompatible Parameter Values

Incorrect Facility Type

Interface Does Not Support Loopback Type

Internal Access Failed

Internal Database Error

Invalid DCC

Invalid Performance Monitoring Mode

Invalid Protection Group

Invalid Time Period

SDBE (continued)

Location Value Invalid

Loopback Is Invalid

Loopback Port In Service

Mac Address Not Supported By Payload

Object Not Provisioned

Operation Not Supported On EC1 Interface

STS Not Provisioned

Synchronization Configuration Not Available

Synchronization Status Messaging(SSM) Not Supported On EC1 Interface

Synchronization Status Messaging(SSM) Not Supported On SDH

Used Frame Format Does Not Support Synchronization Status Messaging(SSM)

VT Not Provisioned

SDLD

Duplex Unit Locked

SDNA

Active TCC Not Ready

Standby TCC Not Ready

SNCC

Replace This Message When A SNCC message is needed

SNCN

Cannot Switch To Inferior Reference Source

Clock Source Failed

Command Not Implemented

Cross-Connection Type Not Supported In TL1

Invalid Clock Source

Requested Direction Not Supported

STS Rate Changing Not Supported

SNNS

Reference Not From Optical Card

SNPR

Cannot Get Role Of Port

SNVS

Already Switched To Internal Reference Source

BLSR East Operation Already Set

BLSR West Operation Already Set

Cannot Operate Loopback In Current Cross-connection State

Cannot Operate Loopback In Current State

Facility Not Part Of BLSR

Invalid AINS Soak Time

Invalid Admin State

Invalid BLSR Element

Invalid Clock Source

SNVS (continued)

Invalid Equipment State

Loopback Already In Progress

Loopback Not In Progress

No Switch In Progress

Protection Group Does Not Exist

Protection Unit Active

Working Unit Already Active

Working Unit Already Standby

SOSE

Unrecognized Message Type

SPFA

Cannot Get Current Card Status

Protection Unit Failed Or Missing

SPLD

Cannot Create 1+1 Protection Group

Cannot Delete Equipment

Equipment In Use

FTP Task Is Busy

Facility Is Busy

Protection Unit Locked

SRAC

Invalid Connection Type

SRCN

Already In Requested Mode

Requested Condition Already Exists

SROF

1+1 Protection Group Not Found

ALS Mode Does Not Allow Laser Restart

Active Flash Not Ready

All DCCs In Use

BLSR In Use

BLSR Protect STS Path List Is Empty

Can Not Get IOS Config Source Origin

Cannot Access 1+1 Line

Cannot Access 1+1 Protected Line

Cannot Access 2 Fiber BLSR

Cannot Access 4 Fiber BLSR East Protection

Cannot Access 4 Fiber BLSR West Protection

Cannot Access 4F BLSR

Cannot Access Alarm Log

Cannot Access BLSR

Cannot Access BLSR 2 Wire Line

SROF (continued)

Cannot Access Cross-Connection

Cannot Access DCC

Cannot Access Facility

Cannot Access Performance Monitoring Statistics

Cannot Access Protected Equipment

Cannot Access Protection Group Information

Cannot Access Protection Group Name

Cannot Access Protection Group Reversion Information

Cannot Access STS

Cannot Access TAP

Cannot Access Unprotected Line

Cannot Access Unprotected Line

Cannot Access VT

Cannot Change Ethernet IP With DHCP Provisioned

Cannot Change Ethernet IP With OSPF Provisioned

Cannot Change XTC Protection Group

Cannot Create Cross-Connection Between Incompatible Interfaces

Cannot Create Protection Group

Cannot Create TAP

Cannot Create TAP On Last VT

Cannot Create Ycable Protection

Cannot Delete Cross-Connection

Cannot Delete Last Drop

Cannot Delete Protection Group

Cannot Disable DWRAP With FEC Enabled

Cannot Disable DWRAP With GCC Enabled

Cannot Edit Ethernet IP

Cannot Edit STS

Cannot Enable FEC When G.709 Is Disabled

Cannot Enable FEC With DWRAP Disabled

Cannot Perform ACO

Cannot Provision Equipment

Cannot Provision Protection Equipment

Cannot Set Bidirectional Protection Group

Cannot Set DCC When Digital Wrapper Is Enabled

Cannot Set GCC When DWRAP Is Disabled

SROF (continued)

Cannot Set NodeId

Cannot Set Payload Type

Cannot Set Protection Group Name

Cannot Set Protection Group Revertive Behavior

Cannot Set RingId

Cannot Set Span Revertive Mode Unless 4-Fiber Ring

Cannot Set Span Revertive Time In Non-revertive Mode

Cannot Set Span Revertive Time Unless 4-Fiber Ring

Cannot Set Termination Mode

Cannot Set Wave Length

Cannot Switch For Specified Connection Type

Cannot Switch For Specified Path

Cannot Update Synchronization Reference List

Command Not Supported

Cross-Connection Creation Failed

Cross-Connection Does Not Exist

DCC Does Not Exist

DCC Not In Use

DWRAP Not Enabled

Database Is Busy

Element Not Found

Equipment Does Not Match Request

Equipment Does Not Support Cross-connection Loopback

Ethernet IP And Default Router IP Subnets Are Different

Expected Trace Size Exceeds Trace Format Limit

Facility Does Not Support Laser Restart

Facility Not Protected

Facility Not Provisioned

Flash Is Busy

Generation1 Does Not Support Given Quality Of RES

Get IOR Failed

Host Not In IP Address Format

Insufficient Path Width For Cross-Connection

Insufficient Path Width For Test Access

Internal Exercise Failure

Internal Facility Type Failure

SROF (continued)

Invalid ALS Recovery Interval

Invalid ALS Recovery Pulse Width

Invalid Control Type (CONTTYPE) For AID

Invalid Cross-Connection Path

Invalid Cross-Connection Type For Drops

Invalid Drop Path

Invalid FTP Username/Password

Invalid Loopback Provision

Invalid Operation For Connection Type

Invalid Operation For Specified Path

Invalid Path

Invalid Protection Group

Invalid Protection Switch Operation

Invalid State When Loopback Present

Invalid Subnet Mask

Invalid Synchronization Source

Invalid UPSR Path

J0 Section Trace Level Not Supported By 10GE Payload Type

Laser Was Not Shutdown.Cannot Restart Laser

Loopback Not Allowed On Drop Path

Loopback Type Does Not Match

MIC Cards Cannot Be Reset

Maximum User Limit Reached

No Start-Up IOS Config

Operate Alarm Cutoff Failed

Operation Not Supported

Parameter Not Supported When DWRAP Is Enabled

Path Already In Use

Path Specified Is Not Valid

Path Used For Test Access

Peer Equipment Attributes Do Not Match

Peer Equipment Type Does Not Match

Peer Payload Type Does Not Match

Peer Termination Mode Does Not Match

Pool Does Not Exist

Protect Port Active

SROF (continued)

Protection Switching Failed

Protection Type Mismatch

Provisioning Rules Failed

Regeneration Group Already Exist

Regeneration Group Does Not Exist

Requested Operation Failed

Ring Reversion Failed

SDBER Out Of Range

SFBER Out Of Range

STS Does Not Exist

STS Does Not Have TAP

STS Path Width Does Not Match

STS Path Width Does Not Match

Section Termination Mode Not Supported

Software Activation Failed

Software Download Failed

Software Error

Software Error

Software Revertion Failed

Span Reversion Failed

Specified Operation Is Not Valid

Standby Flash Not Ready

Synchronization/Timing Parameters Not Supported With DWRAP Enabled

TTI Trace Not Allowed With G709 Disabled

Test Access Active

Trace Format Not Supported By J0 Section Trace

Trace Format Not Supported By TTI Section Trace

Trace Message Size Exceeds Trace Format Limit

Trace Mode Incompatible With Termination Mode

Trace Mode Not Supported

Trace Not Supported By 10GE Payload Type

Unprovisioning Rules Failed

Unsupported BLSR STS Path Operation

Unsupported Command Type

Unsupported Element Type

VT Does Not Exist

SROF (continued)

VT Does Not Have TAP

Wavelength Value Not Supported

Working/Peer Card In Use

XC Card Does Not Support VT Cross-Connection

XC Card Not Present

Y-Cable Protection Does Not Exist

SRQN

BLSR Creation Failed

BLSR Deletion Failed

BLSR Does Not Exist

BLSR Editing Failed

Cannot Edit SENDDUS On Protect Port

Cannot Edit SYNCMSG On Protect Port

DCC Not Allowed In SDH Mode

DCC Not Allowed On Protect Port

Data Access Request Failed

Invalid Mode For Current Configuration

Invalid Request

Protect Card Does Not Support Electrical Protection

Protect Card Does Not Support Protection Type

SDH Not Allowed

SDH Not Allowed On Protect Port

SDH Not Allowed With DCC

SDH Not Allowed With SENDDUS

SDH Not Allowed With SYNCMSG

SENDDUS Not Allowed With SDH Mode

SYNCMSG Not Allowed With SDH Mode

Sync Status Messaging(SSM) Not Allowed With SDH Mode

SSRD

Manual Switch Cannot Override Forced Switch

Switch Request Denied

SSRE

Memory Resources Exceeded

SWFA

Working Unit Failed Or Missing

SWLD

Working Unit Locked