Step 1 |
enable
Example:
|
Enables privileged EXEC mode.
|
Step 2 |
configure
terminal
Example:
Device# configure terminal
|
Enters global configuration mode.
|
Step 3 |
ip
sla
operation-number
Example:
|
Begins configuration for an IP SLAs operation and enters IP SLA configuration mode.
|
Step 4 |
ethernet
echo
mpid
mp-id
domain
domain-name
{evc
evc-id |
port |
vlan
vlan-id}
Example:
Device(config-ip-sla)# ethernet echo mpid 23 domain testdomain vlan 34
|
For a ping operation only: Configures the IP SLAs operation as an Ethernet ping operation and enters Ethernet echo configuration mode.
Note
| Depending on your release, the
evc evc-id keyword and argument combination may not be available for this command.
|
|
Step 5 |
ethernet
jitter
mpid
mp-id
domain
domain-name
{evc
evc-id |
port |
vlan
vlan-id} [interval
interframe-interval] [num-frames
frames-number]
Example:
Device(config-ip-sla)# ethernet jitter mpid 23 domain testdomain evc testevc interval 20 num-frames 30
|
For a jitter operation only: Configures the IP SLAs operation as an Ethernet jitter operation and enters Ethernet jitter configuration mode.
Note
| Depending on your release, the
evc evc-id keyword and argument combination may not be available for this command.
|
|
Step 6 |
cos
cos-value
Example:
Device(config-ip-sla-ethernet-echo)# cos 2
|
(Optional) Sets the class of service for an IP SLAs Ethernet operation.
Note
| For this and the remaining steps, the configuration mode shown in the example is for configuring an Ethernet echo operation. However, the commands are the same in the Ethernet jitter configuration mode.
|
|
Step 7 |
frequency
seconds
Example:
Device(config-ip-sla-ethernet-echo)# frequency 30
|
(Optional) Sets the rate at which a specified IP SLAs operation repeats.
|
Step 8 |
history
history-parameter
Example:
Device(config-ip-sla-ethernet-echo)# history hours-of-statistics-kept 3
|
(Optional) Specifies the parameters used for gathering statistical history information for an IP SLAs operation.
|
Step 9 |
owner
owner-id
Example:
Device(config-ip-sla-ethernet-echo)# owner admin
|
(Optional) Configures the Simple Network Management Protocol (SNMP) owner of an IP SLAs operation.
|
Step 10 |
request-data-size
bytes
Example:
Device(config-ip-sla-ethernet-echo)# request-data-size 64
|
(Optional) Sets the padding size for the data frame of an IP SLAs Ethernet operation.
The default value for IP SLAs Ethernet ping operations is 66 bytes. The default value for IP SLAs Ethernet jitter operations is 51 bytes.
|
Step 11 |
tag
text
Example:
Device(config-ip-sla-ethernet-echo)# tag TelnetPollSever1
|
(Optional) Creates a user-specified identifier for an IP SLAs operation.
|
Step 12 |
threshold
milliseconds
Example:
Device(config-ip-sla-ethernet-echo)# threshold 10000
|
(Optional) Sets the upper threshold value for calculating network monitoring statistics created by an IP SLAs operation.
|
Step 13 |
timeout
milliseconds
Example:
Device(config-ip-sla-ethernet-echo)# timeout 10000
|
(Optional) Sets the amount of time an IP SLAs operation waits for a response from its request packet.
|
Step 14 |
end
Example:
Device(config-ip-sla-ethernet-echo)# end
|
Exits to privileged EXEC mode.
|
Step 15 |
show
ip
sla
configuration
[operation-number]
Example:
Device# show ip sla configuration 1
|
(Optional) Displays configuration values including all defaults for all IP SLAs operations or a specified operation.
|
Step 16 |
show
ip
sla
application
Example:
Device# show ip sla application
|
(Optional) Displays global information about supported IP SLAs features.
|