For detailed information about the hardware supported in Cisco 1x2 / Compact Shelf RPD Software and its maintenance releases, see:

http://www.cisco.com/c/en/us/td/docs/cable/cbr/installation/guide/b_cbr_how_and_what_to_order.html.

The new software feature for Cisco 1x2 / Compact Shelf RPD Software 6.3 release is:

The new software features for Cisco 1x2 / Compact Shelf RPD Software 6.2 release are:

SFP support for 1RU shelf

The following SFPs are supported:

• SFP-10G-AOC3M(10-2847-01)

• SFP-10G-LR-S(10-3107-01)

• DWDM-SFP10G-C(10-3036-01)

R-PHY(config)#sfp itu [port_no] [channel_no]

For more information on the mapping relationship between channel_no with wavelength, go through Cisco 10GBASE Dense Wavelength-Division Multiplexing SFP+ Modules Data Sheet.

Read count TLV 100.21/22/23/17 support

Read count TLV 100.21 HostResourcesSystem, TLV 100.22 HostResourcesStorage, TLV 100.23 HostResourcesSwRun and TLV 100.17 IpDefaultRouter is supported in RPD V6.2 Release.

Read count TLV 74/75 support

Read count TLV 100.74 DsOob551Perf and TLV 100.75 DsOob552Perf is supported in RPD V6.2 Release

Analog Tx/Rx modules alarm threshold setting

You can set Analog Tx/Rx modules alarm threshold by TLV 21 VendorSpecificExtension sub TLV 21.13 AnalogTxPower and TLV 21.14 AnalogRxPower.

• TLV definition:

  Table 2. AnalogTxPower Object

  Attribute Name	Type	Access	Type constraints	Units	TLV Type
  TxIndex	UnsignedByte	Key			21.13.1
  MajorLowTH	UnsignedShort	Write-only			21.13.2
  MinorLowTH	UnsignedShort	Write-only			21.13.3
  NormalTH	UnsignedShort	Write-only			21.13.4
  MinorHighTH	UnsignedShort	Write-only			21.13.5

  Table 3. AnalogRxPower Object

  Attribute Name	Type	Access	Type constraints	Units	TLV Type
  RxIndex	UnsignedByte	Key			21.14.1
  MajorLowTH	UnsignedShort	Write-only			21.14.2
  MinorLowTH	UnsignedShort	Write-only			21.14.3
  NormalTH	UnsignedShort	Write-only			21.14.4
  MinorHighTH	UnsignedShort	Write-only			21.14.5

• You can verify Analog Tx/Rx modules alarm threshold setting on RPD by below CLI:

  R-PHY#show environment table 49
  sensor_id: 49
  name: TX1_OPT_PWR_MON
  type: power
  unit: mW
  state            low            high
  ------------------------------------
  MAJOR-LOW        N/A            0.00
  MINOR-LOW        0.00           0.49
  NORMAL           0.50           0.99
  MINOR-HIGH       1.00           1.49
  MAJOR-HIGH       1.50           N/A
  poll_interval: 2
  sensor_state: N/A
  sensor_value: N/A
  
  Configured Values (Currently Used Values):
  
  state            low            high
  ------------------------------------
  MAJOR-LOW        N/A            0.00
  MINOR-LOW        0.00           0.49
  NORMAL           0.50           0.99
  MINOR-HIGH       1.00           1.49
  MAJOR-HIGH       1.50           N/A
  sensor_state: N/A
  R-PHY#show environment table 50
  sensor_id: 50
  name: RX1_OPT_PWR_MON
  type: power
  unit: mW
  state            low            high
  ------------------------------------
  MAJOR-LOW        N/A            0.00
  MINOR-LOW        0.00           0.49
  NORMAL           0.50           1.49
  MINOR-HIGH       1.50           1.99
  MAJOR-HIGH       2.00           N/A
  poll_interval: 2
  sensor_state: N/A
  sensor_value: N/A
  
  Configured Values (Currently Used Values):
  state            low            high
  ------------------------------------
  MAJOR-LOW        N/A            0.00
  MINOR-LOW        0.00           0.49
  NORMAL           0.50           1.49
  MINOR-HIGH       1.50           1.99
  MAJOR-HIGH       2.00           N/A
  sensor_state: N/A
  
  

The new software features for Cisco 1x2 / Compact Shelf RPD Software 6.1 release are:

Disable LLDP by TLV

In Cisco 1x2 / Compact Shelf RPD Software 6.1, LldpEnable TLV is introduced to enable or disable the LLDP protocol. The RPD which supports this attribute MUST preserve the value of this attribute in it non-volatile configuration store.

Value is defined as the boolean value to enable/disable LLDP operation on the RPD. The values are:

• 0 – LLDP is disabled.

• 1 – LLDP is enabled.

The selection of a default value is left to vendor’s choice.

New added events

New events are supported for DHCPv6 and supported networks.

Factory reset support

Starting from Cisco 1x2 / Compact Shelf RPD Software 6.1, factory reset and NVRAM reset via TLV and CLI are supported.

• factoryReset: The device restores the factory configuration and performs a hard reset. You can perform a factoryReset by running the following:

  
  R-PHY>enable 
  R-PHY#reboot factory-reset
  

• nvReset: The device clears non-volatile configuration and performs a hard reset. You can perform a nvReset by running the following:

  
  R-PHY>enable 
  R-PHY#reboot nvreset
  

Support for Narrowband Digital Forward And Narrowband Digital Return

Narrowband Digital Forward (NDF) refers to the digitizing of an analog portion of the downstream spectrum at the headend, sending the digital samples as payload in [DEPI] packets to the RPD, and then re-creating the original analog stream at the RPD. NDF supports services such as FM Broadcast, DAB+ Broadcast, and OOB signals for Forward Sweep, DS Leakage, and Element management.

Narrowband Digital Return (NDR) refers to the digitizing of an analog portion of the upstream spectrum at the RPD, sending the digital samples as payload in [R-UEPI] packets to the CMTS, and then re-creating the original analog stream at the headend. NDR supports legacy OOB signals for Reverse Sweep, Return Path Monitoring, FSK based HMS, and other FSK based telemetry signals.

The following commands are introduced on the Cisco 1x2 / Compact Shelf RPD Software 6.1 release:

• show downstream oob configuration ndf – Provides the NDF configuration in RPD for each NDF channel configured. It displays PHY information for the NDF session.

• show upstream oob configuration ndr – Provides the NDR configuration in RPD for each of NDR channel configured. It displays PHY and L2TP information.

• show downstream oob counter ndf – Provides the NDF packet counter from BCM for each NDF channel configured. It is a clear on read counter.

• show upstream oob counter ndr – Provides the internal mapping of RPD channels and its corresponding channel configured in core.

• show oob fpga ndf-status – Provides the NDF FPGA status for each NDF channel configured.

• show oob ds-mapping – Provides the internal mapping of RPD channels and its corresponding channel configured in the core.

For more information, see the Cisco cBR Series Converged Broadband Routers Quality of Services Configuration Guide for Cisco IOS XE Fuji 16.10.x and the Cisco CMTS Cable Command Reference Guide.

The modified software features for Cisco 1x2 / Compact Shelf RPD Software 6.3 release are:

R-PHY#show sfp info 0
== SFP A0 EEPROM CONTENT ==
Reg 0x0000: 03 04 07 10 00 00 00 00  00 00 00 06 67 00 00 00 
Reg 0x0010: 08 02 00 1e 43 49 53 43  4f 2d 46 49 4e 49 53 41 
Reg 0x0020: 52 20 20 20 00 00 90 65  46 54 4c 58 38 35 37 34 
Reg 0x0030: 44 33 42 43 4c 2d 43 53  41 20 20 20 03 52 00 c9 
Reg 0x0040: 00 1a 00 00 46 4e 53 32  31 31 37 30 35 4e 33 20 
Reg 0x0050: 20 20 20 20 31 37 30 34  32 33 20 20 68 80 05 b0 
Reg 0x0060: 00 00 02 f1 56 b3 87 75  7d 68 08 b3 35 21 09 66 
Reg 0x0070: f4 da 7e 00 00 00 00 00  00 00 00 00 ba a3 f6 f2 
Base ID Fields:
 Identifier              :0x03
 Ext.Identifier          :0x04
 Connector               :0x07
 Compliance Code         :0x10
 Transceiver Codes       :0x10 0x0 0x0 0x0 0x0 0x0 0x0 0x0 
 Encoding                :0x06
 BR,Nominal              :10300 Mbps
 Rate Identifier         :0x00
 Length(9um)-km          :0x00
 Length(9um)             :0x00
 Length(50 um OM2)       :0x08
 Length(62.5 um OM1)     :0x02
 Length(Copper)          :0x00
 Length(OM3)             :0x1e
 Vendor name             :CISCO-FINISAR   
 Vendor OUI              :0x0 0x90 0x65 
 Vendor PN               :FTLX8574D3BCL-CS
 Vendor Rev              :0x41 0x20 0x20 0x20 
 Wavelength              :850 nM
 CC Base                 :0xc9
Extended ID Fields:
 Options                 :0x0 0x1a 
 BR, max                 :0x00
 BR, min                 :0x00
 Vendor SN               :FNS211705N3     
 Date                    :2017-04-23
 Diagnostic Type         :0x68
 Enhanced Options        :0x80
 SFP-8472 Compliance     :0x05
 CC EXT                  :0xb0
 Vendor Specific         :0x0 0x0 0x2 0xf1 0x56 0xb3 0x87 0x75 0x7d 0x68 0x8 0xb3 0x35 0x21 0x9 0x66 
                         :0xf4 0xda 0x7e 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0xba 0xa3 0xf6 0xf2 
== SFP A2 EEPROM CONTENT ==
Reg 0x0000: 4b 00 fb 00 46 00 00 00  8d cc 74 04 87 5a 7a 76 
Reg 0x0010: 19 64 07 d0 18 6a 09 c4  39 c7 02 e5 1c f5 07 46 
Reg 0x0020: 3d e9 01 97 1f 07 03 ff  00 00 00 00 00 00 00 00 
Reg 0x0030: 00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00 
Reg 0x0040: 00 00 00 00 3f 80 00 00  00 00 00 00 01 00 00 00 
Reg 0x0050: 01 00 00 00 01 00 00 00  01 00 00 00 00 00 00 bf 
Reg 0x0060: 26 88 80 8a 11 4f 14 70  16 f6 00 00 00 00 00 00 
Reg 0x0070: 00 40 00 00 00 40 00 00  ff ff ff ff ff ff ff 01 
Reg 0x0080: 43 4f 55 49 41 38 4e 43  41 41 31 30 2d 32 34 31 
Reg 0x0090: 35 2d 30 33 56 30 33 20  01 00 46 00 00 00 00 c6 
Reg 0x00a0: 00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00 
Reg 0x00b0: 00 00 00 00 00 00 00 00  00 00 00 00 00 00 aa aa 
Reg 0x00c0: 53 46 50 2d 31 30 47 2d  53 52 20 20 20 20 20 20 
Reg 0x00d0: 20 20 20 20 34 38 00 00  00 00 00 00 00 00 00 3c 
Reg 0x00e0: 1e 20 2a 2a 31 34 29 36  00 00 00 00 00 00 00 00 
Reg 0x00f0: 00 00 00 00 00 56 00 00  ff ff ff ff 00 00 00 00 
 
SFP Detail Diagnostic Information (Internal Calibration):
                 Measured    High Alarm  High Warning  Low Alarm   Low Warning:
 Temperature:       38 C         75 C         70 C         -5 C         0 C
 Voltage    :     3.29 V       3.63 V       3.46 V       2.97 V      3.13 V
 BiasCurrent:     8.86 mA     13.00 mA     12.50 mA      4.00 mA     5.00 mA
 Tx Power   :    -2.81 dBm     1.70 dBm    -1.30 dBm   -11.30 dBm   -7.30 dBm
 Rx Power   :    -2.31 dBm     2.00 dBm    -1.00 dBm   -13.90 dBm   -9.90 dBm
 
Checking for Alarms and Warnings:
Done Checking for Alarms and Warnings
 
Diag & Control/Status:
 Alarm & Warning         :0x4b 0x0 0xfb 0x0 0x46 0x0 0x0 0x0 0x8d 0xcc 0x74 0x4 0x87 0x5a 0x7a 0x76 
                         :0x19 0x64 0x7 0xd0 0x18 0x6a 0x9 0xc4 0x39 0xc7 0x2 0xe5 0x1c 0xf5 0x7 0x46 
                         :0x3d 0xe9 0x1 0x97 0x1f 0x7 0x3 0xff 
 Calibration Constants   :0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x3f 0x80 0x0 0x0 
                         :0x0 0x0 0x0 0x0 0x1 0x0 0x0 0x0 0x1 0x0 0x0 0x0 0x1 0x0 0x0 0x0 
                         :0x1 0x0 0x0 0x0 
 CC_DMI                  :0xbf
 Diag Monitor Data       :0x26 0x88 0x80 0x8a 0x11 0x4f 0x14 0x70 0x16 0xf6 
 Status & Control        :0x00
 Reserved SFF-8079       :0x00
 Alarm Flags             :0x00 0x40
 Warning Flags           :0x00 0x40
 Ext Status/Control      :0x00 0x00

There are no integrated features in Cisco 1x2 / Compact Shelf RPD Software 6.3 release.

There are no new hardware feature for Cisco 1x2 / Compact Shelf RPD Software 6.3 release.

There are no new MIBs in Cisco 1x2 / Compact Shelf RPD Software 6.3.