|
|
CSCee18959 |
Core dump to server fails because extra information such as date/time is concatenated to the configured file name to be written to the server. |
CSCti12590 |
Querying "getnext" with ipCidrRouteDest returns an OID that is not lexicographically larger than the queried OID. |
CSCtk15093 |
When the CPEs, connected to DOCSIS 2.0 cable modems from two multicast VPNs and sharing a physical downstream forwarding interface, have joined same IGMP group with Multicast traffics, one CPE in one multicast VPN incorrectly receives traffic destined to a CPE in another multicast VPN. |
CSCti66880 |
The show ip rsvp counters command does not display the port values. |
CSCti72173 |
When there is are a high number of PPPoE sessions on the Cisco uBR10000 series universal broadband router, the LDP high availability process causes high CPU utilization on the secondary PRE. This forces the router to switchover. |
CSCtk96446 |
When creating the OBFL file system for the first time and the uptime_exthist file is empty, there could be a temporary corruption in the flash device. This causes the OBFL Uptime application to stop functioning. |
CSCtl16221 |
When the show licenses command is used, it displays incorrect count of licenses. |
CSCtl22266 |
The DOCSIS general load balancing group information is lost from the mac domain cable modem service group after a PRE switchover occurs. |
CSCtn96470 |
The carrier-to-noise ratio (CNR) accuracy varies on the Cisco uBR-MC3GX60V line card. |
CSCty18719 |
While configuring ACLs from multiple CLI terminals at the same time, the CPU utilization is high and Cisco IOS crashes. |
CSCty99658 |
Packetcable bit is not set for PacketCable Multimedia (PCMM) multicast. |
CSCtz23513 |
During system bootup, the message "%SCHED-7-WATCH" and traceback is observed. |
CSCtz29975 |
In a large scale performance environment, such as eight Cisco uBR-MC3GX60V line cards in (7 + 1) redundancy mode, 120 MAC Domains, and 1000 cable modems, the standby PRE crashes on PRE switchover. |
CSCtz68573 |
When configurations of modular cable controller are deleted, the changes are not synchronized on the protect line card |
CSCtz71368 |
On the Cisco uBR10012 running Cisco IOS Release 12.2(33)SCG, the output of the show hccp linecard subslot modem summary total command does not synchronize with the output of the show cable modem summary total command. |
CSCtz80972 |
After moving the CM from IPv6 online/w-online to IPv4 online/w-online, a traceback occurs. |
CSCua06500 |
When HCCP is unconfigured after a line card switchover, the error message "Bad refcount in datagram_done" is displayed with traceback. |
CSCua11055 |
when HCCP is configured for the Cisco uBR-MC3GX60V line card, followed by a switchover and a revertback occurs, and the card is physically removed and replaced again, |
CSCua11695 |
Spurious memory access when changing the RF channel frequency through SNMP. |
CSCua12085 |
After a Cisco uBR-MC3GX60V line card switchover, the show interface cable command displays incorrect packets input counter after a Cisco uBR-MC3GX60V line card switchover. |
CSCua12456 |
The values for ccwbRFChannelUtilization and docsIfCmtsChannelUtUtilization are calculated incorrectly. |
CSCua13328 |
When a running-configuration that does not have HCCP configured is replaced with a running-configuration that has HCCP configured, error messages are displayed. |
CSCua15263 |
%HCCP-3-CFG_FAIL error message with error code 1 is displayed and traceback is observed when a line card switches over after the wideband SPA is removed. |
CSCua20383 |
The throughput is 8.9 Mpps in system when the traffic is sent from WAN to CPE . |
CSCua25760 |
After a Cisco UBR-MC20X20 line card switchover, error and warning messages are displayed while configuring HCCP. |
CSCua25855 |
When DMIC is enabled and the configuration file name is different for IPv4 and IPv6 policies, cable modem can get IPv4 and IPv6 addresses from the CNR, but fails to get the configuration file. |
CSCua33517 |
When an IP address is not configured as the secondary address, configuration of dhcp-giaddr policy host and secondary addresses under bundle interface is not accepted by the Cisco CMTS. However, no warning message is displayed that the configuration was not accepted. |
CSCua34434 |
Although Alternative Provisioning Mode (APM) is configured as the IP provisioning mode, CM gets dual stack online. |
CSCua35518 |
The cable modem name max-hosts command does not execute correctly. |
CSCua36877 |
When cable modem registration throttling is enabled, cable modem throttling queue size is much larger than actual number of cable modems |
CSCua38362 |
After performing line card and PRE switchover on the Cisco uBR-MC3GX60V line card, The show interface bundle command reports very high input and output rate, as well as high input and output counter values. |
CSCua43769 |
When the same IP address is assigned to two different bundle interfaces, DHCP IP address assign mismatch error is displayed when the same IP address is assigned to two bundle interfaces. |
CSCua45329 |
When Cisco CMTS is configured for IPv4 or IPv6 source-verify dhcp, Cisco CMTS is configured for DOCSIS 3.0 SAV for IPv4 or IPv6 and an upstream packet fails source-verify and to match the SAV subnet prefix, the Cisco CMTS does not issue DHCP Leasequery (LQ). |
CSCua46000 |
When standby PRE fails during the bootup and the "%IDBINDEX_SYNC-4-RESERVE: Failed to lookup existing ifindex for an interface on the Standby, allocating a new ifindex from the Active" error message is observed on the active PRE. |
CSCua48865 |
When the configured service class is removed via SNMP, service class removed via SNMP is removed only in the active PRE, and exists in the standby PRE. |
CSCua49227 |
When multiple telnet sessions are open to operate fiber-node configuration, fiber node configuration error occurs when two telnet sessions are open. |
CSCua57078 |
The standby PRE reloads when redundancy configuration is changed on the active PRE. |
CSCua59985 |
The new active PRE parses an invalid command card x/x No Card license 72X60 after the PRE crash and switchover. |
CSCua60092 |
When there is no SPA card in a slot but the card and no card commands are executed for this slot and then the standby PRE4 is loaded, tracebacks are observed on the standby PRE. |
CSCua62457 |
When two CPEs with duplicate MAC address are online simultaneously, one clear cable host mac-address command can clear only one of these CPEs. |
CSCua65785 |
When a working card switches over to standby mode, wideband configuration cannot be performed using CLI. However, wideband configuration can be performed using SNMP, which causes RF channel inconsistencies between the working and protect line card. |
CSCua69999 |
%NICKEL10G-3-N10GERREVT error message is observed during PXF reload. |
CSCua70281 |
The downstream traffic goes down after PRE switchover. |
CSCua70408 |
The deleted DOCSIS LBG appears in the show running and show cable load commands. |
CSCua73564 |
When a Cisco uBR-MC3GX60 cable interface line card is added to Cisco uBR10012 router, a system log message (%LINEPROTO-X) is generated with a swidb_if_index_link_identity traceback. |
CSCua74462 |
DBG resiliency count and time statistics information is lost after a line card switchover followed by a PRE switchover. |
CSCua74782 |
Line card crashes due to FAUNA fatal error. However, the bits of "FAUNA_GBL_FATAL_INT" register are not set in the crashinfo file. |
CSCua75101 |
DEPI sessions on the Cisco Wideband SPA go down after using shutdown and no shutdown commands for Cisco Wideband SPA. |
CSCua75312 |
When MIB value is set via SNMP, the configuration is inconsistent between working and protect line cards. |
CSCua75325 |
When configuring RF channel bandwidth for interface Wideband-Cable by SNMP operation, if the RF channel is from a different controller, then the RF channel is incorrectly configured on the standby PRE. |
CSCua80124 |
Cable modem is not synchronized with the standby PRE. |
CSCua84970 |
After the no card command is used to remove a line card from running-config, the modular-host subslot configuration for a Wideband SPA can still point to the removed line card. |
CSCua88497 |
Traceback is observed after resetting the SPA card and executing the show controller modular command. |
CSCua90051 |
Fiber node upstream and downstream is inconsistent when the line card is added to HCCP group. |
CSCua90867 |
When the no downstream modular-cable rf-channel command is executed, the system crashes. |
CSCua92314 |
Cable modem may access uninitialized memory address. |
CSCua93169 |
When the IPv6 address is changed in the bundle, DHCPv6 relay source address is incorrect. The old source address still exists. |
CSCua95263 |
MQoS session range with invalid source prefix IP mask defaults to null IP mask (0.0.0.0). |
CSCua97690 |
Inconsistency in different configuration sequences with rate-adapt when upstream utilization optimization is configured locally first and then enabled globally. |
CSCub00817 |
During PXF microcode reload or PRE switchover, the transient error message "%NICKEL10G-3-N10GERREVT: TBB - ERR EVENT MSOP, port 0” is observed. |
CSCub04150 |
After using the hw-module subslot 1/0 shutdown command, saving and reloading the system, DTI card in slot 1/1 cannot bootup. |
CSCub04599 |
On Cisco uBR10000 router, the SAV may not work for DOCSIS 3.0 CM. |
CSCub04652 |
Invalid logging on standby PRE in RPR mode while performing auto-generate on the active PRE. |
CSCub10176 |
When the DTCC card is moved from one slot to another, the MIBs do not change. |
CSCub10389 |
On a primary channel with narrowband modems, when wideband modem is online, those modems should select other channels as the primary channel. |
CSCub14757 |
CM cannot come online when the fiber node contains two controllers RF channel with overlapping frequencies. |
CSCub15514 |
After all the CMs are cleared from CMTS, CMs can still be seen in the pending list of DOCSIS 2.0 LBG. |
CSCub17050 |
When the line card crashes, traceback and the error message “SYS-2-INSCHED” is observed when the line card crashes. |
CSCub17736 |
When large number of CPEs are behind CM online, and test cable dcc command is executed for DCC initialization technique 1, CPUHOG and traceback are observed if DCC is performed when 250 CPEs are behind one modem. |
CSCub23036 |
%SYS-2-MALLOCFAIL error message is observed on cable line cards. |
CSCub25025 |
Cable monitor configuration is rejected for SPA WB interface. |
CSCub25128 |
With a large fiber node and dual-stack configured, "Unexpected fragment sequence number. Got 2 and expected 1" error message is observed on the modem console. Modems cannot come online with IPv6 when the error message appears. |
CSCub27638 |
When one modem is configured with more than two different classifiers and the microcode reload pxf command is executed, the DS traffic, except for the first and last classifierstrafficonthemodem,isdropped.' |
CSCub27686 |
Assertion fails with spurious memory access when the show cable modem service-flow verbose command is executed. |
CSCub28061 |
The following error message and traceback are observed: | | |"%HCCP-3-CFG_FAIL: Configuration failed. Parsing on Cable5/0/0 (error 1) -Process= "HCCP_LC_CTRL", ipl= 0, pid= 386" |
CSCub30613 |
Error message "DSID_DUPLICATE" and traceback observed after doing LC switch over on Cisco uBR-MC20X20V line card |
CSCub33063 |
The show controllers integrated-cable mapping rf-channel command output is unclear on CiscouBR7200 routers. |
CSCub33605 |
When a cable modem is assigned a load balancing group ID (LBG ID), it fails to move into the designated load balancing group and the modem is not listed in the load balancing group modem list. |
CSCub35871 |
The standby RP may show "%UBR10K_REDUNDANCY-4-RP_HA_STDBY_INCONSISTENT" messages on console, when the line card is reset. |
CSCub37666 |
The CPE type remains static instead of DHCPv6. |
CSCub41631 |
The output of show controllers integrated-cable mapping wb-channel is unclear for Cisco uBR7246 router. |
CSCub41655 |
Inconsistent output of the show controller integrated-cable c ommand. |
CSCub42368 |
The outputs of the show cable l2-vpn xconnect dot1q-vc-map modem-mac verbose and show cable l2-vpn xconnect mpls-vc-map modem-mac verbose commands are the same for dot1q L2VPN service. |
CSCub43523 |
Switchover fails during the Cisco UBR-RFSW-ADV image upgrade. |
CSCub44765 |
Cable modem cannot get all the IPv4 and IPv6 address via MIB cdxCmToCpeTable when more than 255 IPv6and IPv4 addresses exist in hosts under one cable modem. |
CSCub45028 |
The pending counter does not clear on channel shutdown. |
CSCub47047 |
The shutdown and no shutdown of Cisco uBR-MC3GX60V GE (SFP) port causes insert OIR event in call home. |
CSCub47647 |
When the protect line card is down and the line card switches over, the cable modem or CPE goes offline. However, the show ipv6 dhcp relay binding and show ipv6 route static commands still show the PD route. |
CSCub52401 |
IPv6 spoof MAC detection is not available in IPv6 calling path. |
CSCub53183 |
Two CISCO-ENTITY-FRU-CONTROL MIB errors are seen when the hw-module subslot subslot# reload command is used for any SPA on the UBR1000 platform. |
CSCub54877 |
A dynamic bonding group (DBG) is not automatically shut after the RF impairment recovery. |
CSCub54975 |
The error message "%C10K-3-LC_ERR" is observed during normal system bootup. |
CSCub57967 |
One Cisco uBR-MC3GX60V line card works as the modular host line card of SPA and protect card at the same time. |
CSCub59823 |
The value of docsIf3BondingGrpCfgChList using SNMP GET is null for cross controller. |
CSCub64405 |
A wrong "IP MTU" configuration message appears in interface configuration when 10 Gigabit Ethernet SPA is configured with MTU and the 10 Gigabit Ethernet SPA interface is removed and added. |
CSCub64465 |
The show pxf cpu mpls command displays incorrect VRF table IDs for MPLS labels. |
CSCub64552 |
Configuration is not recovered after shutdown operation on Cisco UBR-MC20X20V line card. |
CSCub65411 |
All routed packets are incorrectly counted in the show interface stats command on tunnel interface. |
CSCub67370 |
IPv6 ACL cannot be applied to GRE tunnel interface through startup-config file after reboot. |
CSCub69512 |
Error message and tracebacks are observed when configuring Q-in-Q backhaul sub-interfaces. |
CSCub69658 |
The Cisco uBR10012 router creates a MAC address-based filter if TLV35 is configured in modem.config file. If some CPEs have multiple IPv4 addresses, the number of CPEs behind the modem could exceed limit set by TLV35. This violates DOCSIS 3.0 specification. |
CSCub74764 |
If docsLoadBalGrpDefaultPolicy is configured with a non-existent policy ID, then the show running-config command displays the non-existent policy ID. |
CSCub76060 |
When the cable ds-resiliency command is used, the warning message "Wideband-Cable6/0/0:0 is set to WB resiliency bonding group. Remove all existing configurations" is displayed. However, only rf-channel and bundle configurations are removed. The admission-control or other configurations are not removed. |
CSCub76172 |
Memory leakage occurs when the virtual bundle fails. |
CSCub76413 |
When QoS is disabled on PRE5, the throughput is downgraded to 3.3Mpps for IPv4 MPLS VPN downstream traffic (WAN->CPE). |
CSCub79220 |
Using the show idb comand, the link status of GigabitEthernet interfaces on standby PRE on Cisco uBR-MC3GX60V line card is hsown erroneously. |
CSCub79278 |
When IPv6 address is added to rogue database DHCPv6 leasequery sending should be be disabled. However, DHCPv6 leasequery sending continues and traffic continues to be sent from the rogue IPv6 address. |
CSCub79300 |
After repeatedly adding and removing trusted IPv6 addresses with the same IP address, mask, and ToS values, the "no" form of the service divert-rate-limit trusted-site-ipv6 command fails. |
CSCub83514 |
When timeout parameters are configured using commands, the no form of the activity-timeout and admission-timeout arguments of the cable service class command fail. |
CSCub83630 |
When an unsupported tunnel mode is configured, all Generic Routing Encapsulation (GRE) tunnel packets are lost. |
CSCub83745 |
When CPEs join and leave mcast groups, the 'Failed to write BPI entry to Jib3DS 0" error is displayed. |
CSCub88667 |
After a Dynamic Bonding Change (DBC) operation, the cable modem cannot be pinged. |
CSCub88707 |
The Cisco CMTS router denies requests for giant IPC packets after a route processor switchover. |
CSCub88833 |
Running the clear ip access-list dynamic counters command triggers spurious memory access and adds traceback information in the logging buffer of the Cisco uBR10012 router. |
CSCub89046 |
CPE is added to wrong cable modem after leasequery. |
CSCub89510 |
The Cisco CMTS router does not reject real-time polling service (RTPS) service flow with an invalid policy. |
CSCub91406 |
The output of show pxf cable feature-table does not distinguish between DHCPv4 and DHCPv6 source verify inquiries when the source verification of the IPv6 packets is configured on the bundle interface. |
CSCub92875 |
The IPv6 neighbor table is not recovered, and some cable modems cannot be pinged after the multicast downstream service identifier (DSID) forwarding capability is disabled on the Cisco CMTS router. |
CSCuc00074 |
Duplicated DSID cable modem fail to synchronise on Cisco Shared Port Adapter (SPA) 520 series. |
CSCuc03382 |
When bays 2 and 3 of Cisco uBR10012 router have Shared Port Adapter cards, and the show diag command is used to get the SPA card information, the show diag command fails. |
CSCuc05554 |
When Performance Routing Engine (PRE) high availability is activated on a bundle interface configured for IPv4 and IPv6 unicast and multicast traffic, Multicast Listener Discovery (MLD) on the bundle interface is disabled. |
CSCuc10438 |
Upstream Bonding Group with ID greater than 65535 do not have any upstream channel members. |
CSCuc11266 |
Error message "cmts_chk_any_spa_ds: p_info is NULL" is displayed for modems that register with the downstream channels on Cisco uBR-MC20X20V line card as primary downstream channels and bonding groups on remote Shared Port Adapter card as downstream bonding groups. |
CSCuc12684 |
Ping DOCSIS test failed for modems showing status as online. Modem fails to drop offline after line card switchover/reverback performance. |
CSCuc15140 |
The SNMP agent does not send any traps when cTap2StreamInterceptEnable is false and cTap2StreamStatus is changed from active to "nonService." |
CSCuc15156 |
When cTap2StreamInterceptEnable is set to false, two debug entries are created (cTap2DebugEntry). |
CSCuc18671 |
The Cisco 5-Port Gigabit Ethernet SPA does not forward downstream TLS dot1q Layer 2 VPN traffic. |
CSCuc21450 |
The Cisco CMTS router allows you to set the submanagement default value to a filter group that does not exist. |
CSCuc33742 |
An FPGA firmware issue might cause a line card crash. |
CSCuc37333 |
JIB3 Register information that is usually collected by using show tech-support or any command used to collect debug information on controllers is missing for Cisco IOS Release 12.2(33)SCG. |
CSCuc37650 |
Field-Programmable Device image upgrade failure while upgrading two or more Shared Port Adapter at the same time. |
CSCuc38680 |
Information for narrow-band downstream channels is not updated when show controller down command is used. |
CSCuc40752 |
When CPU or memory threshold and cable admission-control event cm-register are configured, show cable admission control global command displayed that the counter is increased when current value is higher than threshold. If only cable admission-control event dynamic service command is configured, the counter is not inscreased even when current value is higher than threshold. |
CSCuc41201 |
On reload with a number of interfaces, if line card redundancy is configured in start-up, default service flow is not created on Wideband interface. |
CSCuc43190 |
If you execute the all version of the clear cable modem commands when the number of modems are greater than 1000 and there are more than 10 classifiers per modem the %SYS-2-INTSCHED error message and traceback are displayed. |
CSCuc51823 |
The session on seventh channel drops into IDLE mode when the Cisco CMTS is configured with Cisco IOS Release 12.2(33)SCF4 and the frequency is shifted to 6 MHz. |
CSCuc55282 |
Field-Programmable Device image upgrade using Trivial File Transfer Protocol (TFTP) failed for Shared Port Adapter (SPA) using the upgrade hw-module [ slot slot-number ] file file-url command. |
CSCuc55351 |
After Dynamic Bonding Change (DBC), ping test to online cable modem failed. |
CSCuc57679 |
For a Cisco uBR10012 router configured with more than five Cisco uBR-MC3GX60V line cards, the “%IDBINDEX_SYNC-4-RESERVE: Failed to lookup existing ifindex for an interface on the Standby, allocating a new ifindex from the Active” error message and traceback is displayed. |
CSCuc57809 |
show cable load-balance docsis-group n target command displayed target although there were no load balancing action, after line card high availability activation. |
CSCuc66994 |
Following the use of the show cable modem command, a cable line card (Cisco uBR-MC20X20V or Cisco uBR-MC3GX60V) crashed and %REQGRP-3-SYSCALL error message and traceback is displayed. |
CSCuc69863 |
While configuring a protect tunnel in Downstream External PHY Interface (DEPI) tunnel configuration, configuration of a working tunnel as protect tunnel should be rejected. |
CSCuc70582 |
After deleting a line card using the no form of card slot/subslot command, the no form of cable monitor interface command fails. |
CSCuc71501 |
In the CMTS IOS downstream data forwarding path, if the CMTS subscriber database has a Customer-premises equipment (CPE), the CMTS does not issue a DHCPv6 leasequery which can recover all CPE data including adding the CPE to the Neighbor Discovery (ND) cache. |
CSCuc72969 |
Cable filter group configuration lost on leasequery after CMTS reload or line card Online Insertion and Removal (OIR). |
CSCuc75845 |
When cable clock dti command is configured or removed, UC Command 403 failure error is displayed. |
CSCuc77773 |
When multiple SNMP traps are configured to one snmp-server host, some traps are lost. |
CSCuc77926 |
Spurious memory access error message and traceback displayed on both active and standby Performance Router Engines (PREs). |
CSCuc78831 |
The effect of plim input map ip precedence command configured on wide area network Shared Port Adapter (SPA) interface is not removed after plim input map ip dscp-based command configured. |
CSCuc80671 |
When the show cr10k-rp wideband-cable queue command is used, the queues corresponding to the single SID specified in the command, are not displayed. |
CSCuc82877 |
Route Processor console displays the “SPA TSM Error: PSM_GOT_INSERTED_WHEN_NOT_EXPECTED” error. |
CSCuc83205 |
The error message “Spurious access@cmts_hccp_process_inter_sid_instance_loc” is displayed when Hot Standby Connection to Connection Protocol (HCCP) is configured on Cisco uBR-MC3GX60V line card. |
CSCuc84764 |
A DEPI tunnel that is configured as protect-tunnel for another tunnel, can be removed using the no depi-tunnel command, if no sessions are established using that DEPI tunnel. If any sessions are established using the DEPI tunnel then it cannot be removed and a warning message is displayed. |
CSCuc87108 |
When a DEPI class name is configured with the maximum number of characters (80), the DEPI class name is saved. However, the name is displayed with only 79 characters when the show running-config command is used. |
CSCuc87362 |
When c802tapStreamStatus is configured to 2 (nonService) from 1 (active), no trap or cTap2DebugEntry is generated for it. However, when c802tapStreamStatus is changed from nonService to Active, a trap and cTap2DebugEntry is generated.The cTap2DebugMessage displayed is "MAC Stream modification successful". |
CSCuc88089 |
Memory leakage observed on HCCP_DATA_P2 process, when HCCP is configured on Cisco uBR-MC3GX60V line card. |
CSCuc92143 |
The subinterface configured on DEPI interface is still displayed after the SPA card has been removed using the no card command. |
CSCuc92908 |
When a protect tunnel is overwritten by another tunnel configuration, it cannot be configured again. To configure it again, the overwritten tunnel must be configured with the protect-tunnel command and then the no form of the protect-tunnel command must be used. |
CSCuc92930 |
When the show interface command is used on the 1Gbps SPA card to display Flow Control, Flow Control is not displayed. |
CSCuc99577 |
If the destination IP is used to configure a protect tunnel, belongs to a working tunnel, the show depi session command displays wrong information about the primary and secondary activity status. |
CSCuc99918 |
When the show depi session endpoints command is executed, the result does not have any header line. |
CSCud00216 |
When a cable bundle is configured with wrong cable bundle number and Request for Services (RFS) is configured, the cable bundle mismatch error is displayed. Then if the cable bundle is configured with the correct bundle number, “Bundle already exists on this interface” is displayed. This occurs on Cisco uBR10012 router with Cisco uBR-MC3GX60V line card. |
CSCud00474 |
Peer QAM State remains in the Idle state during line card high availability recovery for the primary DEPI session, resulting in modems dropping offline for service groups configured on the working Cisco uBR-MC3GX60V line card. This event is observed on hardware module subslot reset as well as line card OIR. |
CSCud05267 |
When Policy-map configuration on interfaces is reloaded, the configuration fails and the error message “%MCE-3-TCAM_FULL_NOMERGE: TCAM full, QoS Policy-map <policy-map name> could not be loaded” is displayed. |
CSCud06317 |
Traceback error occurs when no card command is executed on Cisco uBR10012 router with wideband SPA. |
CSCud06503 |
One vty is configured with a QOS rule using cable qos enforce-rule command and the rule is removed on second vty using no form of the command. When the Synchronous Transport Module (STM) is configured through the second vty, the PRE crashes. |
CSCud06636 |
When two Telnet sessions running in cable fiber-node configuration mode and one Telnet mode exits from the configuration mode, the second Telnet session does not exit from the cable fiber-node configuration mode. |
CSCud06765 |
When one vty session is in redundancy configuration mode and line card redundancy group is removed in another vty session, line card redundancy configuration on the first vty is unsuccessfull. |
CSCud06795 |
The PRE crashes after exiting from a non-existent pseudowire class. |
CSCud07118 |
When one user is accessing a Broadband Aggregation group (BBA-Group), and another user removes the BBA-Group, the PRE crashes because the first user is still accessing the removed BBA-Group. |
CSCud09868 |
When no forms of cable qos enforce-rule commands are used, the configuration develops errors. |
CSCud11596 |
After LCSO reverts back to the primary line card, the cable upstream resiliency on-failure reset-modem command fails. |
CSCud11616 |
During cable modem configuration, if the slot range is 5 to 8, the RF channel status is displayed as Integrated-cable rf-channel instead of modular-cable rf-channel, although the RF channel is configured as modular-cable rf-channel. |
CSCud13370 |
During bootup, if the jacket cards are reset and PRE switches over before two line cards are online, the modems on both the line cards drop offline. This occurs when only DOCSIS Timing Interface (DTI) of a line card is not connected to DTI server and modems on all line cards use that line card as clock. |
CSCud16147 |
When DTI status error (bug CSCud44570) occurs during Route Processor Redundancy mode switchover, and the jacket card is removed incorrectly, errors and tracebacks occur. |
CSCud16252 |
Traceback error occurs when standby PRE5 is removed and modems are online via IPv4 and IPv6 with call-home configurations enabled. |
CSCud17425 |
show cable rf-status command with integrated-cable option displays status of cable interface although there is no integrated cable interface on Cisco uBR10012 router. |
CSCud17431 |
PRE resets in silent mode when parser error and traceback occurs and the “%SNMP-5-LINK_DOWN” and “%REDUNDANCY-3-STANDBY_LOST” errors are displayed: |
CSCud18726 |
show diag crashdump command is not supported in Cisco uBR10012 router. |
CSCud19901 |
During DTCC OIR, Wrong TSS Phy error messages are displayed. |
CSCud21149 |
When more than one sub-interface is configured in DEPI, removal of the interface with no card command fails. After SSO the standby PRE resets repeatedly due to bulk-sync failure. |
CSCud22477 |
%PARSER-4-BADRANGELONGLONG error message is displayed when cable admission-control max-reserved-bandwidth command is used. |
CSCud23971 |
If the secondary channel width ( last-choice-width in cable upstream channel-width command) is greater than 1.6 MHz in the A-TDMA configuration, then the secondary channel width is not changed when the DOCSIS mode is changed from A-TDMA to SCDMA mode. |
CSCud25251 |
MATCHED cmts_ipv6_match_prefix messages displayed for PRE5 running Version 12.2(122SC_20121115) should be hidden. |
CSCud25721 |
When CMTS connects first to low-priority collector and then high-priority collector, the CMTS switches over. After the high-priority collector is disconnected, the CMTS switches over to the low-priority collector, but the IPDR data exporter fails. |
CSCud25804 |
After PXF is reloaded, “%IPC-5-INVALID: Message Port index Dest Port” error message is displayed and the PRE5 crashes. |
CSCud25827 |
After the PRE switches over, the jacket card resets and the “%PXF_NICKEL-3-IRONBUS_NOTRUNNING”, and “%IPC-2-INVALIDZONE: Invalid IPC Zone 0xF00000” error messages are displayed. |
CSCud26231 |
When two different types of SPA cards are located on the same Spumoni, one type of SPA card is recognised as the other type of SPA card. |
CSCud26404 |
The show interface counters command displays wrong packet counter information when 10 G EtherChannel port-channel sends high amount of traffic to the 10G SPA. |
CSCud28665 |
When line card redundancy is configured and the line card is removed from the slot, no card inserted message is displayed and removal of redundancy configuration is not allowed. Support for removal of redundancy configuration after removal of line card is required. |
CSCud30202 |
Cable modems do not come online after upgrading an image and reloading the PRE. The cable modems come online after completing shut/no shut operation on the interface and activation of line card high availability. |
CSCud31088 |
The onboard failure logging (OBFL) uptime application fails due to a temporary corruption of flash drive and the uptime extend history file is empty, when the OBFL file system is created for the first time. The OBFL uptime application does not recover from this error. |
CSCud32155 |
When the license revoke command is used, the license count does not reduce or change, on Cisco uBR10012 router with Cisco uBR-MC3GX60V line card running Cisco IOS Release 12.2(33)SCF4. |
CSCud32428 |
During feature interaction testing on PRE5 for Cross Controller Bonding, Dynamic Bonding Group Resiliency and Multicast on Pre5 features, while doing line card switchover, the "Error - STAT_SET non local ReMan 5/1 nui30" error occured. |
CSCud32588 |
When configuring output service policy on port-channel interface, the MQC queues are not created for port-channel interface. This behavior is seen on PRE5 10GE and SPA 10GE interfaces. |
CSCud33825 |
During PRE reload after it has crashed, all the line cards fail to reboot and the poer LED indicators of the line cards remain OFF. |
CSCud33959 |
After a successful dynamic bonding change (DBC) to Modena Receive Channel Configuration (RCC) by configuring a rcc-template, the traffic is lost because Modena does not support Baseline Privacy Interface(BPI) Advanced Encryption Standard (AES). |
CSCud34360 |
PacketCable MultiMedia (PCMM) multicast session does not recover after a PRE switchover on a SPA wideband interface on Cisco uBR-MC3GX60V line card. |
CSCud35507 |
While configuring multiple IA_PD/IA_NA addresses for CPE, the maximum number of IPv6 address configurable is 8. |
CSCud37649 |
The show cable modem summary cable upstream command fails and shows the wrong prompt. |
CSCud37833 |
When the NGSPA on slots 3/2 and 3/3 and the Jacket card is reset, the "obfl_process_dequeue" error and traceback occurs. |
CSCud37959 |
When the start-up configuration runs, the no card command in the configuration fails in the active PRE. The no card command succeeds in the standby PRE. |
CSCud39795 |
The shut command executed in the Modena IP interface fails and the physical link does not shut down. |
CSCud40161 |
When line card switchover occurs, "cmts_dsg_adv_check_rule_validity" fails, displaying the "%SCHED-2-EDISMSCRIT" error and "HCCP_LC_DATA" traceback. |
CSCud40550 |
When the 4jacket-1 card resets and is reloading, the SNMP requests fail, displaying traceback error. |
CSCud40556 |
Cable modem status messages for static multicast downstream ID display the unicast downstream IDs in logs. |
CSCud42262 |
If the SPA is used as downstream channel while the Cisco uBR-MC3GX60V line card switches over, traffic is interrupted for 10 seconds. |
CSCud42325 |
After RPR switchover, irrespective of whether there is an NGSPA loaded on the router or not, the DOCSIS Timing, Communication and Control (DTCC) is not detected and DTI status is reported wrongly. The DTCC cannot be ecovered without the power cycle of the router chassis. (HUDSON?) |
CSCud44283 |
With DOCSIS 3.0 and wideband modems connected to Cisco uBR10012 router, after a dynamic bonding change, the timing effect of modems increases to two times the normal timing effect. |
CSCud44570 |
In Route Processor Redundancy mode, during PRE switch over, DTCC is not detected and DOCSIS Timing Interface (DTI) displays wrong status. |
CSCud44837 |
When there is no change in Management Console (MC) interface, but wideband interface channel has changed, valid wideband interface does not associate with mac-domain. Wideband interfaces are not displayed in rcc-list. |
CSCud45121 |
When VPN Routing and Forwarding (VRF) is enabled, some cable modems on the VPN do not have correct Customer-premises Equipment (CPE) prefix and cannot be pinged. |
CSCud45313 |
When load balancing group configuration is written on line card with protect downstream channels and the CMTS is reloaded, the protect member of the line card is removed. |
CSCud45920 |
When the system is configured with logging console and logging console guaranteed commands, the log messages are not displayed in proper order on the console. |
CSCud45934 |
When the number of channels in a MD-DS-SG is greater than 24, the wideband cable modems do not move to w-online state on certain primary interface. |
CSCud46092 |
PRE4 on Cisco uBR10012 router running Cisco IOS Release 12.2(33) SCF3 crashes with the "%SYS-6-STACKLOW: Stack for process C10K card_oir_up_action_process running low, 0/6000" error message. |
CSCud47331 |
When a logical upstream DOCSIS mode is configured as TDMA or TDMA/A-TDMA mixed mode and channel width is configured as 200000 Hz, Cisco uBR-MC20X20V line card crashes. |
CSCud48789 |
When the CMTS sends an incomplete dynamic bonding change request (DBC-REQ), a modem responds with a dynamic bonding change response (DBC-RSP) to indicate the error to the CMTS. The CMTS resends the DBC-REQ but does not respond to the bandwidth request from the modem's transmit channel set (TCS). |
CSCud50053 |
After cable modems are in w-online mode, when dynamic bonding change is executed using test cable dbc Mac-address sfid SFID Bonding-group-id command, the CMTS log indicates successful dynamic bonding change, but the show cable modem Mac-address service-flow command displays that the related FrwdIF change failed. |
CSCud52134 |
If the modem is dual-stack, and comes online after the protect line card is ready, after line card switchover, both md_ds_sg_id and md_us_sg_id of modem are reset to zero. |
CSCud52766 |
When the PRE switches from active PRE A to standby PRE B; line card switches from working line card to protect line card and the PRE switches back to PRE A with upstream traffic of more than 10M pps ipv6, a traceback observed |
CSCud53156 |
PRE crashes with the "TCP-2-INVALIDTCB Invalid TCB pointer: 0x14A20804 -Process="IPDR_EXP_PROC", ipl= 0, pid= 89" error message and a traceback. |
CSCud53756 |
All the modems on a specific upstream channel drop offline and the Map Late Flush Count increases with "test cable bcm3142 errors 2" reports. Other upstream channels on the same line card are not affected. |
CSCud54997 |
When a large number of modems come online simultaneously and undergo dynamic bonding change, the status of a number of modems is wrongly displayed as cloned. |
CSCud55368 |
SNMP MIB ifXTable provides wrong values for BroadcastPkts value. |
CSCud56136 |
When CPE with multiple IA_NA/IA_PD IPv6 addresses comes online and line card switches over, some or all the addresses are lost. |
CSCud56903 |
When CMTS is reloaded, “Config Sync: Bulk-sync failure” error leads to standby PRE reset. |
CSCud57765 |
When two different types of SPA cards are located on the same Spumoni, one type of SPA card is recognised as the other type of SPA card. |
CSCud58359 |
After dynamic bonding change, the service-flow management selected the wideband interface with lower bandwidth instead of the wideband interface with higher bandwidth. |
CSCud58757 |
When all MAC domain interfaces are put into the online insertion and removal (OIR) state, by using the hw-module stop command on the Cisco uBR-MC88V line cards, the DOCSIS Set-Top Gateway (DSG) configuration on cable interfaces is not restored. |
CSCud59107 |
After line card is reset using hw_module reset command and PRE switchover, all the DEPI sessions fail and the "%C10KEVENTMGR-4-IRONBUS_FAULT" error message is displayed. |
CSCud59604 |
After line card is reset using hw_module reset command and PRE switchover, all the DEPI sessions fail and the "%C10KEVENTMGR-4-IRONBUS_FAULT" error message is displayed. |
CSCud60444 |
When the connection is unstable, though the outstanding queue is full, the IPDR exporter fails. |
CSCud60449 |
When no ipdr template command when IPDR exporter running, the CMTS crashes. |
CSCud60925 |
When CPU usage is high, and bi-direction traffic is sent, then "spurious memory access" error when do linecard switchover & revert. |
CSCud61008 |
Configuring upstream channel for Load Balancing Group (LBG) in descending order fails without displaying an error message. |
CSCud61083 |
After multiple line card switches over, the line card crashes due to memory shortfall. |
CSCud64045 |
If cable ip-init command is configured on cable interface, then line card switched over, the configuration synchronises with the protect line card, but if docsIf3MdCfgIpProvMode is set through SNMP, the configuration does not synchronise with the protect line card causing inconsistency issues. |
CSCud66762 |
After no dest-ip command is used and PRE switched over, the DEPI tunnel fails. |
CSCud76053 |
When the active PRE switches over to the standby PRE, the cable interface ifSpeed value changes. |
CSCud76618 |
Under normal conditions, the fiber node information is not updated when the frequency for the upstream group is changed through spectrum management. |
CSCud78232 |
When show cable modem resiliency status command is used wrongly, show cable modem summary wb-rfs command displays the same output for both modular-cable and integrated-cable options |
CSCud78262 |
During normal operation, when a crash occurs or the hw-module command resets the protect line card no SNMP trap is sent. |
CSCud78401 |
In the output of show cable modem, if the IP address of a modem is a long value, it extends to next column. |
CSCud78797 |
When the show packetcable gate ipv6 summary command is used, wrong output for PacketCable gates associated with IPv6 subscriber IDs for DQOS, is displayed. |
CSCud78839 |
When the fiber-node is configured and the show cable fiber-node association command is used, the narrow band channel ID is zero for Cisco uBR-MC20X20V and Cisco uBR-MC3GX60V line cards. |
CSCud79411 |
When one Gigabit Ethernet interface is shutdown and no shutdown command used for interface range mode without configuring the begin interface range , the IF state of standby PRE is erroneous. |
CSCud80873 |
When configuring the downstream modular-cable rf-channel command, the standby PRE crashes. |
CSCud81164 |
With Cisco uBR-MC3GX60V line card configured as protect line card, when snmp (setccwbRFChannelModulation) is set on the protect line card, inconsistency issues are observed between working line card and protect line card. |
CSCud83345 |
When the 4jacket-1 card is pre-configure without the physical jacket on the CMTS and PRE switchover is performed, the elements of entPhysicalEntry table for 4jacket-1 containers are not synchronised. |
CSCud83465 |
When the modem configuration file is changed and shut/no shut operation is performed on the Gigabit Ethernet port to allow the modems offline or online, status of some modems is displayed as w-online but the modems and the CPEs behind them cannot be pinged. The BPI key for these modems is not correct. |
CSCud84792 |
When the free memory in the router is very low, the PRE crashes with the the exception vector 1500 error message. |
CSCud85776 |
When there are several DOCSIS Set-top gateway (DSG) classifiers and channel grouping domains (CGDs) in one mac-domain, then adding more CGDs to the mac-domain leads to CPU Hog and traceback messages. |
CSCud85809 |
When a SNMP polling script is used to poll SNMP objects with a large number of online cable modems, CPU Hog occurs with DTCC card and line card crash. |
CSCud86014 |
The upstream scheduling for Unsolicited Grants (UGS) service flows (SFs) does not work correctly when the upstream channel bonding (USCB) feature is enabled in D-PON mode. The traffic flows only on one upstream channel with no packets flowing on the other channel. |
CSCud86837 |
When default class is not configured in the policy map, the sum of class bandwidth configured in one policy map could exceed 100 percent and no alert message is displayed. |
CSCud87301 |
If priority is configured first and then schedule type is configured, priority configutation is not valid and an error message is not displayed to show invalid configuration sequence. |
CSCud89401 |
On Cisco uBR10012 router with Cisco uBR-MC3GX60V line card running Cisco IOS Release 12.2(33)SCF4, the Cisco uBR-MC3GX60V line card crashed and displayed the "SYS-2-INTSCHED 'idle' at level 1 -Process= "CMTS MAC Parser", ipl= 1, pid= 84" error message with tracebacks. |
CSCud90921 |
Spacing between "Prim Sid" and "Online Status" columns in the output of the of show cable modem registered/unregister command. |
CSCud91095 |
When a certain configuration sequence is used, the A and L bits are set wrongly in the router advertisement (RA) message sent out by CMTS bundle interface. |
CSCud91942 |
When an invalid RF channel number is configured on a wideband SPA and Cisco uBR-MC3GX60V line card, the PRE crashes. |
CSCud92352 |
When hostname styled DSG classifiers were configured successfully, CPU Hog message on DSG process is displayed. |
CSCue44744 |
During the inital configuration of DEPI tunnels, the Cisco CMTS router experiences issues with establishing DEPI tunnels connections. The Cisco CMTS router may also stop responding when interfacing with RF Gateway-1 or other third-party EQAM devices. |
CSCue53762 |
When packetcable is enabled, the following error message is displayed on the console and is logged in the sytem log:
%UBR10000-4-PKTCBL_GATE_FAILURE: Packetcable gate failed
This occurs when packetcable call is going to be deleted. This message is a false alarm. There is no actual error and no impact on services. |