Document ID: 27000
The Terminal Access Controller Access Control System (TACACS+) protocol provides access control for routers, Network Access Servers (NASs), or other devices through one or more daemon servers. It encrypts all traffic between the NAS and daemon using TCP communications for reliable delivery.
This document provides troubleshooting information for the Content Services Switch (CSS) and TACACS+. You can configure the CSS as a client of a TACACS+ server, providing a method for authentication of users, and authorization and accounting of configuration and non-configuration commands. This feature is available in WebNS 5.03.
Note: Refer to Configuring the CSS as a Client of a TACACS+ Server for more information.
There are no specific requirements for this document.
This document is not restricted to specific software and hardware versions.
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Refer to Cisco Technical Tips Conventions for more information on document conventions.
When you attempt to log in to the CSS with a TACACS+ user, the login does not work.
Generally, when TACACS+ authentication does not work with a CSS, the problem is usually either a configuration issue on either the CSS or the TACACS+ server. The first thing that you need to check is whether you have configured the CSS as a client of a TACACS+ server.
When you have checked this, there is additional logging that you can use on the CSS in order to determine the problem. Complete these steps to turn on logging.
On the CSS, enter debug mode.
CSS# llama CSS(debug)# mask tac 0x3 CSS(debug)# exit CSS# configure CSS(config)# logging subsystem security level debug-7 CSS(config)# logging subsystem netman level info-6 CSS(config)# exit CSS# logon !--- This logs messages to the screen.
In order to disable logging, issue these commands:
CSS# llama CSS(debug)# mask tac 0x0 CSS(debug)# exit CSS# no logon
These messages can appear:
SEP 10 08:30:10 5/1 99 SECURITY-7: SECMGR:SecurityAuth:Request from 0x20204b0c SEP 10 08:30:10 5/1 100 SECURITY-7: SECMGR:SecurityMgrProc:Try Primary SEP 10 08:30:10 5/1 101 SECURITY-7: Security Manager sending error 7 reply to ller 20201c00
These messages indicate that the CSS tries to communicate with the TACACS+ server, but the TACACS+ server rejects the CSS. error 7 means that the TACACS+ key entered in the CSS does not match the key on the TACACS+ server.
A successful login through a TACACS+ server shows this message (note the sending success 0 reply):
SEP 10 08:31:46 5/1 107 SECURITY-7: SECMGR:SecurityAuth:Request from 0x20204b0d SEP 10 08:31:46 5/1 108 SECURITY-7: SECMGR:SecurityMgrProc:Try Primary SEP 10 08:31:47 5/1 109 SECURITY-7: Security Manager sending success 0 reply to caller 20201c00 SEP 10 08:31:47 5/1 110 SECURITY-7: SECMGR:SecurityMgrProc:Try Done, Send 0x2020 4b0d
The most common mistake when you set up a CSS to work with a TACACS+ server is actually very simple. This command tells the CSS what key to use to communicate with the TACACS+ server:
CSS(config)# tacacs-server key system enterkeyhere
This key can be either clear text or DES encrypted. The clear text key is DES encrypted before the key is placed in the running configuration. To make a key clear text, put it in quotes. To make it DES encrypted, do not use quotes. The important thing is to know if the TACACS+ key is DES encrypted or if the key is clear text. After you issue the command, match the key of the CSS to the key that the TACACS+ server uses.
- Configuring the CSS as a Client of a TACACS+ Server
- Configuring TACACS+ and Extended TACACS+
- Password Recovery Procedure for the Cisco CSS 11000 Series
- Technical Support & Documentation - Cisco Systems
|Updated: May 03, 2004||Document ID: 27000|