Document ID: 107615
This document describes situations in which a Cisco IOS® router might experience high CPU utilization due to either the Border Gateway Protocol (BGP) router process or the BGP scanner process, as shown in the output of the show process cpu command. The duration of the high CPU condition varies based on a number of conditions, in particular the size of the Internet routing table and the number of routes that a particular router holds in its routing and BGP tables.
The show process cpu command shows CPU utilization averaged over the past five seconds, one minute, and five minutes. CPU utilization numbers do not provide a true linear indication of the utilization with respect to the offered load. These are some of the major reasons:
In a real world network, the CPU has to handle various system maintenance functions, such as network management.
The CPU has to process periodic and event-triggered routing updates.
There are other internal system overhead operations, such as polling for resource availability, that are not proportional to traffic load.
You can also use the show processes cpu command in order to obtain some indication of CPU activity.
Once you read this document, you should understand the role of each BGP process and when each process runs. In addition, you should understand BGP convergence and techniques to optimize convergence time.
Refer to Cisco Technical Tips Conventions for more information on document conventions.
This document requires an understanding of how to interpret the show process cpu command. Refer to Troubleshooting High CPU Utilization on Cisco Routers as reference material.
The information in this document is based on Cisco IOS Software Release 12.0.
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
A Cisco IOS process, in general, consists of the individual threads and associated data that perform tasks, such as system maintenance, switching packets, and implementing routing protocols. Several Cisco IOS processes executed on the router enable BGP to run. Use the show process cpu | include BGP command to see the amount of CPU utilization due to BGP processes.
This table lists the function of the BGP processes and shows that each process runs at different times, depending on the tasks that it handles. Because the BGP scanner and BGP router processes are responsible for a large amount of calculations, you may see high CPU due to either one of these processes. The following sections discuss these processes in greater detail.
|BGP Open||Performs BGP peer establishment.||At initialization, when establishing a TCP connection with a BGP peer.|
|BGP I/O||Handles queueing and processing of BGP packets, such as UPDATES and KEEPALIVES.||As BGP control packets are received.|
|BGP Scanner||Walks the BGP table and confirms reachability of the next hops. BGP scanner also checks conditional-advertisement to determine whether or not BGP should advertise condition prefixes, performs route dampening. In an MPLS VPN environment, BGP scanner imports and exports routes into a particular VPN routing and forwarding instance (VRF).||Once a minute.|
|BGP Router||Calculates the best BGP path and processes any route "churn". It also sends and receives routes, establishes peers, and interacts with the routing information base (RIB).||Once per second and when adding, removing, or soft-reconfiguring a BGP peer.|
High CPU due to the BGP scanner process can be expected for short durations on a router carrying a large Internet routing table. Once a minute, BGP scanner walks the BGP RIB table and performs important maintenance tasks. These tasks include checking the next-hop referenced in the router's BGP table and verifying that the next-hop devices can be reached. Thus, a large BGP table takes an equivalently large amount of time to be walked and validated.
Because the BGP Scanner process runs through the entire BGP table, the duration of the high CPU condition varies with the number of neighbors and the number of routes learned per neighbor. Use the show ip bgp summary and show ip route summary commands to capture this information.
The BGP scanner process walks the BGP table to update any data structures and walks the routing table for route redistribution purposes. (In this context, the routing table is also known as the routing information base (RIB), which the router outputs when you execute the show ip route command). Both tables are stored separately in the router's memory and can be very large, thus consuming CPU cycles.
The following sample output of the debug ip bgp updates command captures an execution of BGP scanner, which starts scanning at the lowest numbered prefix or 0.0.0.0.
router# 2d17h: BGP: scanning routing tables 2d17h: BGP: 220.127.116.11 computing updates, neighbor version 8, table version 9, starting at 0.0.0.0 2d17h: BGP: 18.104.22.168 update run completed, ran for 0ms, neighbor version 8, start version 9, throttled to 9, check point net 0.0.0.0 2d17h: BGP: 22.214.171.124 computing updates, neighbor version 8, table version 9, starting at 0.0.0.0 2d17h: BGP: 126.96.36.199 update run completed, ran for 4ms, neighbor version 8, start version 9, throttled to 9, check point net 0.0.0.0 router#
While BGP scanner runs, low priority processes need to wait a longer time to access the CPU. One low priority process controls Internet Control Message Protocol (ICMP) packets such as pings. Packets destined to or originated from the router may experience higher than expected latency since the ICMP process must wait behind BGP scanner. The cycle is that BGP scanner runs for some time and suspends itself, and then ICMP runs. In contrast, pings sent through a router should be switched via Cisco Express Forwarding (CEF) and should not experience any additional latency. When troubleshooting periodic spikes in latency, compare forwarding times for packets forwarded through a router against packets processed directly by the CPU on the router.
Note: Ping commands that specify IP options, such as record route, also require direct processing by the CPU and may experience longer forwarding delays.
Use the show process | include bgp scanner command to see the CPU priority. The value of "Lsi" in the following sample output uses "L" to refer to a low priority process.
6513# show processes | include BGP Scanner 172 Lsi 407A1BFC 29144 29130 1000 8384/9000 0 BGP Scanner
The BGP router process runs about once per second to check for work. BGP convergence defines the duration between the time when the first BGP peer is established and the point at which BGP is converged. In order to ensure the shortest possible convergence times, BGP router consumes all free CPU cycles. However, after it starts, it relinquishes (or suspends) the CPU intermittently.
Convergence time is a direct measurement of how long BGP router spends on the CPU, not the total time. This procedure shows a high CPU condition during BGP convergence and exchanges BGP prefixes with two external BGP (eBGP) peers.
Capture a baseline for normal CPU utilization before starting the test.
router# show process cpu CPU utilization for five seconds: 0%/0%; one minute: 4%; five minutes: 5%
Once the test starts, the CPU reaches 100 percent utilization. The show process cpu command shows that the high CPU condition is caused by BGP router, denoted by 139 (the IOS process ID for BGP router) in the following output.
router# show process cpu CPU utilization for five seconds: 100%/0%; one minute: 99%; five minutes: 81% !--- Output omitted. 139 6795740 1020252 6660 88.34% 91.63% 74.01% 0 BGP Router
Monitor the router by capturing multiple outputs of the show ip bgp summary and show process cpu commands during the event. The show ip bgp summary command captures the state of the BGP neighbors.
router# show ip bgp summary Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 10.1.1.1 4 64512 309453 157389 19981 0 253 22:06:44 111633 172.16.1.1 4 65101 188934 1047 40081 41 0 00:07:51 58430
When the router completes prefix exchange with its BGP peers, the CPU utilization rates should return to normal levels. The computed one minute and five minute averages will settle back down as well and may show higher than normal levels for a longer period than the five seconds rate.
router# show process cpu CPU utilization for five seconds: 3%/0%; one minute: 82%; five minutes: 91%
Use the captured output of the above show commands to calculate the BGP convergence time. In particular, use the "Up/Down" column of the show ip bgp summary command and compare the start and stop times of the high CPU condition. Typically, BGP convergence can take several minutes when exchanging a large Internet routing table.
Note: The high CPU on the device could also be due to the instability of the BGP table. If the router is receiving two copies of the routing table, one from the EBGP peering with the ISP and the other from the IBGP peering in the network. The root cause for this is the amount of memory on the device. Cisco recommends a minimum of 1 Gig of RAM for a single copy of the internet routing table. To circumvent this instability, increase the RAM on the device or filter the prefixes so that the BGP table and the memory occupied by it is relieved.
As the number of routes in the Internet routing table grows, so too does the time it takes for BGP to converge. In general, convergence is defined as the process of bringing all route tables to a state of consistency. BGP is considered to be converged when the following conditions are true:
All routes have been accepted.
All routes have been installed in the routing table.
The table version for all peers equals the table version of the BGP table.
The InQ and OutQ for all peers is zero.
This section describes some IOS performance improvements to reduce BGP convergence time, which result in a reduction of a high CPU condition due to a BGP process.
Instead of queueing data once a second, BGP now queues data aggressively from the BGP OutQ to the TCP socket for each peer until the OutQs have drained completely. Since BGP now sends at a faster rate, BGP converges more quickly.
While they help simplify BGP configuration, BGP peer groups also can enhance scalability. All peer group members must share a common outbound policy. Thus, the same update packets can be sent to each group member, reducing the number of CPU cycles that BGP requires to advertise routes to peers. In other words, with peer groups, BGP walks the BGP table only on the peer group leader, filters the prefixes through the outbound policies, and generates updates, which it sends to the peer group leader. In turn, the leader replicates the updates to group members with which it is synchronized. Without peer groups, BGP must walk the table for every peer, filter prefixes through outbound policies, and generate updates that are sent only to the one peer.
All TCP sessions are bounded by a limit on the number of bytes that can be transported in a single packet. This limit, known as the Maximum Segment Size (MSS), is 536 bytes by default. In other words, TCP breaks up packets in a transmit queue into 536 byte chunks before passing packets down to the IP layer. Use the show ip bgp neighbors | include max data command to display the MSS of BGP peers:
Router# show ip bgp neighbors | include max data Datagrams (max data segment is 536 bytes): Datagrams (max data segment is 536 bytes): Datagrams (max data segment is 536 bytes): Datagrams (max data segment is 536 bytes):
The advantage of a 536 byte MSS is that packets are not likely to be fragmented at an IP device along the path to the destination since most links use an MTU of at least 1500 bytes. The disadvantage is that smaller packets increase the amount of bandwidth used to transport overhead. Since BGP builds a TCP connection to all peers, a 536 byte MSS affects BGP convergence times.
The solution is to enable the Path MTU (PMTU) feature, using the ip tcp path-mtu-discovery command. You can use this feature to dynamically determine how large the MSS value can be without creating packets that need to be fragmented. PMTU allows TCP to determine the smallest MTU size among all links in a TCP session. TCP then uses this MTU value, minus room for the IP and TCP headers, as the MSS for the session. If a TCP session only traverses Ethernet segments, then the MSS will be 1460 bytes. If it only traverses Packet over SONET (POS) segments, then the MSS will be 4430 bytes. The increase in MSS from 536 to 1460 or 4430 bytes reduces TCP/IP overhead, which helps BGP converge faster.
After enabling PMTU, again use the show ip bgp neighbors | include max data command to see the MSS value per peer:
Router# show ip bgp neighbors | include max data Datagrams (max data segment is 1460 bytes): Datagrams (max data segment is 1460 bytes): Datagrams (max data segment is 1460 bytes): Datagrams (max data segment is 1460 bytes):
If BGP is advertising thousands of routes to many peers, TCP must transmit thousands of packets in a short duration. The BGP peers receive these packets and send TCP acknowledgements to the advertising BGP speaker, which causes the BGP speaker to receive a flood of TCP ACKs in a short period of time. If the ACKs arrive at a rate that is too high for the route processor, packets back up in inbound interface queues. By default, router interfaces use an input queue size of 75 packets. In addition, special control packets such as BGP UPDATES use a special queue with Selective Packet Discard (SPD). This special queue holds 100 packets. During BGP convergence, TCP ACKs can fill quickly the 175 spots of input buffering and newly arriving packets must be dropped. On routers with 15 or more BGP peers and exchange of the full Internet routing table, over 10,000 drops per interface per minute may be seen. Here is example output from a router 15 minutes after reboot:
Router# show interface pos 8/0 | include input queue Output queue 0/40, 0 drops; input queue 0/75, 278637 drops Router#
Increasing the interface input queue depth (using the hold-queue <1-4096> in command) helps reduce the number of dropped TCP ACKs, which reduces the amount of work BGP must do to converge. Normally, a value of 1000 resolves problems caused by input queue drops.
Note: The Cisco 12000 Series now uses a default SPD headroom value of 1000. It retains the default input queue size of 75. Use the show spd command to view these special input queues.
IOS 12.0(19)S includes several optimizations to the BGP peer group code to improve update packing and replication. Before we discuss these improvements, let's look at update packing and replication in more detail.
A BGP update consists of a combination of attributes (such as MED = 50 and LOCAL_PREF = 120) and a list of Network Layer Reachability Information (NLRI) prefixes which share that combination of attributes. The more NLRI prefixes that BGP can list in a single update, the faster BGP can converge since overhead (such as IP, TCP, and BGP headers) is reduced. "Update packing" refers to the packing of NLRI into BGP updates. For example, if a BGP table holds 100,000 routes with 15,000 unique attribute combinations, BGP needs to send only 15,000 updates if NLRI is packed with 100 percent efficiency.
Note: Zero percent packing efficiency means that BGP would need to send 100,000 updates in this environment.
Use the show ip bgp peer-group command to view the efficiency of the BGP updates.
If a peer group member is "in sync", a BGP router takes an update message formatted for the peer group leader and replicates it for the member. It is far more efficient to replicate an update for a peer group member than it is to reformat the update. For example, assume a peer group has 20 members and all members need to receive 100 BGP messages. One hundred percent replication means that a BGP router formats the 100 messages for the peer group leader and replicates those messages to the other 19 peer group members. To confirm replication improvements, compare the number of messages replicated to the number of messages formatted, as shown by the show ip bgp peer-group command. The improvements make a dramatic difference in convergence times and allow BGP to support many more peers. Let's look at an example.
Use the show ip bgp peer-group command to check the efficiency of update packing and update replication. The following output is from a convergence test with 6 peer groups, 20 peers in each of the first 5 peer groups (eBGP peers) and 100 peers in the sixth peer group (internal BGP (iBGP) peers). Also, the BGP table that was used had 36,250 attribute combinations.
The following sample output of the show ip bgp peer-group | include replicated command on a router running IOS 12.0(18)S displays the following information:
Update messages formatted 836500, replicated 1668500 Update messages formatted 1050000, replicated 1455000 Update messages formatted 660500, replicated 1844500 Update messages formatted 656000, replicated 1849000 Update messages formatted 501250, replicated 2003750 !-- The first five lines are for eBGP peer groups. Update messages formatted 2476715, replicated 12114785 !-- The last line is for an iBGP peer group.
In order to calculate the replication rate for each peer group, divide the number of updates replicated by the number of updates formatted:
1668500/836500 = 1.99 1455000/1050000 = 1.38 1844500/660500 = 2.79 1849000/656000 = 2.81 2003750/501250 = 3.99 12114785/2476715 = 4.89
If BGP replicated perfectly, then the eBGP peer groups would each have a replication rate of 19 because there are 20 peers in the peer group. The update should be formatted for the peer group leader and then replicated to the other 19 peers, providing an optimal replication rate of 19. The ideal replication rate for the iBGP peer group would be 99 since there are 100 peers.
If BGP packed updates perfectly, then we would have only formatted 36,250 updates. We should only need to generate 36,250 updates for each peer group because that is the number of attribute combinations in the BGP table. The iBGP peer group alone formats almost 2,500,000 updates while the eBGP peer groups each generate anywhere from 500,000 to 1,000,000 updates.
On a router running IOS 12.0(19)S, the show ip bgp peer-group | include replicated command provides this information:
Update messages formatted 36250, replicated 688750 Update messages formatted 36250, replicated 688750 Update messages formatted 36250, replicated 688750 Update messages formatted 36250, replicated 688750 Update messages formatted 36250, replicated 688750 Update messages formatted 36250, replicated 3588750
Note: Update packing is optimal. Exactly 36,250 updates are formatted for each peer group.
688750/36250 = 19 688750/36250 = 19 688750/36250 = 19 688750/36250 = 19 688750/36250 = 19 3588750/36250 = 99
Note: Update replication is also perfect.
Use these procedures in order to troubleshoot high CPU due to BGP scanner or BGP router:
Gather information on your BGP topology. Determine the number of BGP peers and the number of routes being advertised by each peer. Is the duration of the high CPU condition reasonable based on your environment?
Determine when the high CPU happens. Does it coincide with a regularly scheduled walk of the BGP table?
Execute the show ip bgp flap-statistics command. Did the high CPU follow an interface flap?
Ping through the router and then ping from the router. ICMP echoes are handled as a low priority process. The document Understanding the Ping and Traceroute Commands explains this in more detail. Ensure regular forwarding is not affected.
Ensure that packets can follow a fast forwarding path by checking whether fast switching and/or CEF are enabled on the inbound and the outbound interfaces. Ensure that you do not see the no ip route-cache cef command on the interface or the no ip cef command on the global configuration. In order to enable CEF in global configuration mode, use the ip cef command.
Obtain output from these commands:
Command Description Show mls cef summary Displays the number of routes in the Multilayer Switching (MLS) hardware Layer 3 switching table for all the protocols. show mls cef maximum-routes Displays the current maximum route system configuration. show mls cef exception <status> Displays information about the Cisco Express Forwarding exception status.
Verify the DRAM on router. As per the recommendation, there should be a minimum of 512 KB of DRAM per BGP peer sending full Internet routing table. If the router has two EBGP peers running full Internet routing table, then 1 GB of DRAM is recommended.
|Updated: Jul 25, 2008||Document ID: 107615|