This document shows you how to configure the Nortel PBX Option 11 E&M Trunk Card. This configuration allows you to connect this card to a Cisco E&M voice port.
There are no specific requirements for this document.
The information in this document is based on these software and hardware versions:
Nortel PBX Software Release 23 or later
Nortel PBX Option 11 Model
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
For more information on document conventions, refer to the Cisco Technical Tips Conventions .
In this section, you are presented with the information you can use in order to configure the features described in this document.
The <RET> throughout the configuration indicates that you need to hit the return key after the respective command parameter.
This document uses this configuration.
#ADDING E&M CARD: !--- Building route data block. Use double digits with !--- route data block. LD16(LOAD 16) REQ:NEW TYPE:RDB CUST:0 DMOD:<RET> ROUT:21 TKTP:TIE ESN:<RET> !--- All returns until ICOG prompt. ICOG:IAO !--- Incoming and outgoing. SRCH:<RET> TRMB:<RET> STEP:<RET> ACOD:71 TARG:0 !--- TGAR 0 and ENDCOST 0. BILN:<RET> !--- All returns until CNTL prompt. CNTL:YES TIMR:<RET> SST:<RET> NEDC:ETH !--. Near end disconnect is set for either. FEDC:ETH !--- Far end disconnect is set for either. CPDC:<RET> !--- All returns until ALRM. <SHIFT>**** LD21 !--- Load 21 to view RDB. REQ:PRT TYPE:RDB CUST:0 ROUT:21 <SHIFT>******** !--- If you need to change from 2 wire to 4 wire cables !--- or vice versa, also change in the PBX config. LD14 !--- Load 14 to add new trunk. REQ:NEW TYPE:TIE TN:9 0 !--- Analog starts at 0, digital starts at 1. XTRK:XEM CUST:0 NCOS:0 RTMB:21 1 MNDN:<RET> TGAR:0 SIGL<RET> EMTY:TY1 !--- Depends on the cabling. CPAD:<RET> STRI:IMM STR0:IMM SUPN:<RET> CLS:UNR DTN !--- Class of service. TKID:<RET> <SHIFT>******** VIEW TRUNK. LD20(LOAD 20) REQ: PRT TYPE: TRK TN: 9 0 RTMB: !--- All returns until the end. <SHIFT>******** !--- After you finish all four trunks, you must enable !--- the trunks. LD32 STAT 9 DISC 9 !--- Disable card 9: the E&M card. ENLC 9 !--- Enable card 9. <SHIFT>******** !--- To modify E&M type, operation (2 or 4 wires) !--- and signaling. LD14 !--- Load 14 to add new trunk. REQ:CHG TYPE:TIE TN:9 0 !--- Analog starts at 0, digital starts at 1. XTRK:XEM CUST:0 NCOS:0 RTMB:21 1 MNDN:<RET> TGAR:0 SIGL<EM4> !--- EM4 For 4-wires, EAM For 2-wires. EMTY:TY2 !--- E&M type 2 depends on cabling. CPAD:<RET> STRI:WNK STR0:WNK SUPN:<RET> CLS:UNR DTN !--- Class of service TKID:<RET> <SHIFT>********
There is currently no verification procedure available for this configuration.
There is currently no specific troubleshooting information available for this configuration.
The Cisco Support Community is a forum for you to ask and answer questions, share suggestions, and collaborate with your peers.
Refer to Cisco Technical Tips Conventions for information on conventions used in this document.