This sample configuration demonstrates how to set up the Cisco Security Appliances (PIX/ASA) for use on a single internal network.
For more information about the PIX/ASA Security Appliance Version 7.x and later with multiple internal networks that connect to the Internet (or an external network) with the command line interface (CLI) or Adaptive Security Device Manager (ASDM) 5.x and later, refer to PIX/ASA 7.x and later: Connecting Multiple Internal Networks with Internet Configuration Example.
Refer to ASA 8.3(x): Connect a Single Internal Network to the Internet for more information on identical configuration with Cisco Adaptive Security Appliance (ASA) with version 8.3 and later.
There are no specific prerequisites for this document.
The information in this document is based on the software and hardware versions below.
Cisco PIX Firewall Software Release 6.x and later
The information presented in this document was created from devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If you are working in a live network, ensure that you understand the potential impact of any command before using it.
This configuration can also be used with the Cisco 5500 Series Adaptive Security Appliance, which runs version 7.x and later.
For more information about document conventions, refer to Cisco Technical Tips Conventions.
In this section, you are presented with the information to configure the features described in this document.
This document uses the network setup shown in the diagram below.
Note: The IP addressing schemes used in this configuration are not legally routable on the Internet. They are RFC 1918 addresses, which have been used in a lab environment.
This document uses the configurations shown below.
|PIX 6.3 Configuration|
PIX Version 6.3(3) nameif ethernet0 outside security0 nameif ethernet1 inside security100 nameif ethernet2 intf2 security10 enable password 8Ry2YjIyt7RRXU24 encrypted passwd 2KFQnbNIdI.2KYOU encrypted hostname pixfirewall !--- Output Suppressed !--- Enable logging. logging on !--- Output Suppressed !--- All interfaces are shutdown by default. interface ethernet0 auto interface ethernet1 auto interface ethernet2 100full mtu outside 1500 mtu inside 1500 mtu intf2 1500 ip address outside 10.165.200.226 255.255.255.224 ip address inside 10.1.1.1 255.255.255.0 ip address intf2 127.0.0.1 255.255.255.255 no failover failover timeout 0:00:00 failover ip address outside 0.0.0.0 failover ip address inside 0.0.0.0 failover ip address intf2 0.0.0.0 arp timeout 14400 !--- Output Suppressed !--- Define a Network Address Translation (NAT) pool that !--- internal hosts use when going out to the Internet. global (outside) 1 10.165.200.227-10.165.200.254 netmask 255.255.255.224 !--- Allow all internal hosts to use !--- the NAT or PAT addresses specified previously. nat (inside) 1 0.0.0.0 0.0.0.0 0 0 !--- Define a default route to the ISP router. route outside 0.0.0.0 0.0.0.0 10.165.200.225 1 !--- Output Suppressed : end [OK]
Building configuration... Current configuration: ! version 12.0 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname R3640_out ! ! username cisco password 0 cisco ! ! ! ! ip subnet-zero ip domain-name cisco.com ! isdn voice-call-failure 0 ! ! interface Ethernet0/1 ip address 10.165.200.225 255.255.255.224 no ip directed-broadcast ! ip classless no ip http server ! ! line con 0 exec-timeout 0 0 length 0 transport input none line aux 0 line vty 0 4 password ww login ! end
Note: Nondefault commands are shown in bold.
pixfirewall# sh run : Saved : PIX Version 8.0(2) ! hostname pixfirewall enable password 2KFQnbNIdI.2KYOU encrypted names ! interface Ethernet0 nameif outside security-level 0 ip address 10.165.200.226 255.255.255.0 ! interface Ethernet1 nameif inside security-level 100 ip address 10.1.1.1 255.255.255.0 ! !--- Output Suppressed !--- Enable logging. logging enable !--- Define a Network Address Translation (NAT) pool that !--- internal hosts use when going out to the Internet. global (outside) 1 10.165.200.227-10.165.200.254 netmask 255.255.255.2244 !--- Allow all internal hosts to use !--- the NAT or PAT addresses specified previously. nat (inside) 1 0.0.0.0 0.0.0.0 0 0 !--- Define a default route to the ISP router. route outside 0.0.0.0 0.0.0.0 10.165.200.225 1 !--- Output Suppressed : end
NOTE:For more information about the configuration of NAT and PAT on PIX/ASA, refer to PIX/ASA 7.x NAT and PAT Statements.
For more information about the configuration of access lists on PIX/ASA, refer toPIX/ASA 7.x : Port Redirection (Forwarding) with nat, global, static and access-list Commands.
There is currently no verification procedure available for this configuration.
This section provides information you can use to troubleshoot your configuration.
NOTE:For more information about how to troubleshoot PIX/ASA, refer to Troubleshoot Connections through the PIX and ASA.
Note: Before issuing debug commands, please see Important Information on Debug Commands.
debug icmp trace - Shows whether ICMP requests from the hosts reach the PIX. To run this debug, you need to add the conduit permit icmp any any command to your configuration. However, when you have finished debugging, remove conduit permit icmp any any command to avoid security risks.
The Cisco Support Community is a forum for you to ask and answer questions, share suggestions, and collaborate with your peers.
Refer to Cisco Technical Tips Conventions for information on conventions used in this document.